Harbor Freight Tools Solar LED Pathway Markers _ 4 Piece Product manual

Solar Pathway Marker
92067
92129
Construction: Cast Aluminum Frame;
6 Bright White LED Lights;
3 Settings: Flash, Off and Constantly On
Safety Precautions and Installation Instructions
1.
2.
3.
4.
5.
Always wear ANSI approved safety
goggles during installation.
Before drilling holes to install this item,
insure that the location that the holes are
to be drilled in is free from hidden wires,
cables, nails, or other obstructions.
Install these lights only where they will not
cause a tripping hazard.
These lights are only intended for
supplemental path lighting; always make
sure that pathways are properly lit by
additional means. Harbor Freight Tools
is not responsible for any personal
injury or property damage caused by
light failure.
NiCad batteries must be disposed of
properly. Do not incinerate. Batteries may
burst, causing personal injury and/or
property damage. Contact your local
hazardous waste disposal authority for
proper disposal.
Installation
Instructions
1.
2.
3.
1/
4” diameter mounting
hardware is not included
and will need to be
supplied. Select an
appropriate location for
the light that will be in full
sunlight.
After ensuring that no
electrical wires, pipes or
other obstructions are
hidden in the object to be
mounted upon, drill two
holes 2-3/4” apart as per
the mounting hardware
supplier’s instructions.
Mount the Marker using
the hardware mentioned
above. Set the switch on
the side to the desired
setting.
®
READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS
BEFORE INSTALLATION OR USE.
3491 Mission Oaks Blvd./Camarillo, CA 93011
Copyright©
2004 by Harbor Freight Tools®. All rights reserved. No portion of
this instruction sheet or any artwork contained herein may be reproduced in any
shape or form without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
SAVE THIS INSTRUCTION SHEET.
IMPORTANT
1. Allow the solar pathway marker to receive at least 8 hours of direct
sunlight with the toggle switch in the “Flash” (Left) or “Constantly On”
(Right) position before first use. From then on the light will turn on and
off automatically.
Note: Always set the switch in the “Flash” or “Constantly On” position
when charging in sunlight. Never set the switch in the “Off” (Mid)
position when charging.
2. During the day, the solar panel converts sunlight into electricity,
recharging the battery. The amount of light it receives depends on
placement, geographic location, weather, and seasonal lighting ability.
To get maximum results, please make sure you install them in a
sunny location where they can get at least 8 hours of direct sunlight a
day. If the weather is cloudy, the battery will not have enough power
for the light to operate at night. It will recharge the next sunny day.
3. Shadow will prevent the solar panel from fully absorbing sunlight,
such as tree branches, any shadow from trees, buildings, etc. Please
change the location of the solar light to the area with more sun.
4. Any other light source, such as street or porch lights, may prevent the
unit from turning on automatically at night.
TROUBLESHOOTING
The performance of solar light depends upon the amount of direct sunlight
available during daylight hours. If your solar light does not operate properly,
refer to possible reasons listed below:
Dim Light:
1. The switch contacts may be poor. Turn the switch on and off several
times to alleviate the problem.
2. The battery may be low or under charged. Make sure the lights are
located in an unobstructed location where they can receive at least 8
hours of sunlight a day. Allow the battery to recharge for 2 full, sunny
days. Overcast days will limit performance.
3. Dirty Solar Panel. A dirty solar panel will not allow the unit to charge,
shortening the life of the battery. Use a soft, damp cloth to clean the
solar panel. Do not use bleaches or detergents.
No Light:
1. The switch may be in the “Off” position. Turn it to the “On” or “Flash”
position.
2. An external light source (i.e. streetlight, porch light, flood light) may
prevent the light from automatically turning on at night. If the Light
Sensor senses the light, the unit will not be turned on. Reposition the
Solar Light.
3. Batteries may need recharging.