Installation and
Getting Started Guide
ProCurve Series
6400cl Switches
www.procurve.com
ProCurve Series 6400cl Switch
Installation and Getting Started Guide
© Copyright 2005, 2006 Hewlett-Packard Development Company,
L.P. The information contained herein is subject to change
without notice.
This document contains proprietary information, which is
protected by copyright. No part of this document may be
photocopied, reproduced, or translated into another
language without prior written consent of Hewlett-Packard.
Publication Number
5991-4701
March 2006
Applicable Products
ProCurve Switch 10-GbE CX4 6400cl-6XG (J8433A)
ProCurve Switch 10-GbE X2 6410cl-6XG (J8474A)
ProCurve 600 Redundant and External
Power Supply (J8168A)
ProCurve 10-GbE X2-SC SR Optic (J8436A)
ProCurve 10-GbE X2-SC LR Optic (J8437A)
ProCurve 10-GbE X2-SC ER Optic (J8438A)
ProCurve 10-GbE CX4 Media Converter (J8439A)
ProCurve 10-GbE X2 CX4 Transceiver (J8440A)
ProCurve 10-GbE Copper Module (J8434A)
ProCurve 10-GbE Media Flex Module (J8435A)
Trademark Credits
Windows NT®, Windows®, and MS Windows® are US
registered trademarks of Microsoft Corporation. Adobe® and
Acrobat® are trademarks of Adobe Systems Incorporated.
Java™ is a US trademark of Sun Microsystems, Inc.
Hewlett-Packard Company
8000 Foothills Boulevard, m/s 5552
Roseville, California 95747-5552
http://www.procurve.com
Disclaimer
HEWLETT-PACKARD COMPANY MAKES NO
WARRANTY OF ANY KIND WITH REGARD TO THIS
MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. Hewlett-Packard
shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing,
performance, or use of this material.
The only warranties for HP products and services are set forth in
the express warranty statements accompanying such products and
services. Nothing herein should be construed as constituting an
additional warranty. HP shall not be liable for technical or editorial
errors or omissions contained herein.
Hewlett-Packard assumes no responsibility for the use or
reliability of its software on equipment that is not furnished by
Hewlett-Packard.
Warranty
See the Customer Support/Warranty booklet included with
the product.
A copy of the specific warranty terms applicable to your
Hewlett-Packard products and replacement parts can be
obtained from your HP Sales and Service Office or
authorized dealer.
Safety
Before installing and operating these products, please read
the “Installation Precautions” in chapter 2, “Installing the
Switch”, and the safety statements in appendix B, “Safety
and EMC Regulatory Statements”.
Contents
Introducing the Switch
Front of the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Console Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Network Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Clear Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Location of Status Indicator LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Expansion cl Module LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Back of the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
cl Module Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
RPS Input Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
Power Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
Switch Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
Installing the Switch
Included Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Installation Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Installation Precautions: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
1. Prepare the Installation Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
2. (Optional) Install or Remove a cl Module . . . . . . . . . . . . . . . . . . . . . 2-7
3. (Optional) Install or Remove a Transceiver . . . . . . . . . . . . . . . . . . . 2-8
To remove the transceiver: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
4. Verify the Switch Passes Self Test . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
LED Behavior: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
5. Mount the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rack or Cabinet Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rack Mounting the Series 6400cl Switch Devices . . . . . . . . . . . .
Horizontal Surface Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-11
2-11
2-12
2-13
iii
6. Connect the Switch to a Power Source . . . . . . . . . . . . . . . . . . . . . . 2-13
7. Connect the Network Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
Connecting a fiber cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
Connecting a copper cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
8. (Optional) Connect a Redundant Power Supply to the
Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15
9.(Optional) Connect a Console to the Switch . . . . . . . . . . . . . . . . . . 2-18
Terminal Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
Direct Console Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19
Sample Network Topologies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20
Three Tier Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20
Remote Campus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21
Flexible Stacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22
High performance stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22
Resiliency Using 6400cl Series as a meshed Cluster . . . . . . . . . . . . . 2-23
Getting Started With Switch Configuration
Recommended Minimal Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Using the Console Setup Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Where to Go From Here . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
To Recover from a Lost Manager Password: . . . . . . . . . . . . . . 3-4
Using the IP Address for Remote Switch Management . . . . . . . . . . . . . . . . 3-5
Starting a Telnet Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Starting a Web Browser Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Troubleshooting
Basic Troubleshooting Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Diagnosing with the LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Proactive Networking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Hardware Diagnostic Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Testing the Switch by Resetting It . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Checking the Switch LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Checking Console Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Testing Switch-to-Device Network Communications . . . . . . . . . . . . . 4-8
Testing End-to-End Network Communications . . . . . . . . . . . . . . . . . . 4-8
iv
Restoring the Factory Default Configuration . . . . . . . . . . . . . . . . . . . . . . . . 4-9
Downloading New Switch Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
ProCurve Customer Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
Before Calling Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
Specifications
Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Acoustic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Lasers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Safety and EMC Regulatory Statements
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Informations concernant la sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2
Hinweise zur Sicherheit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3
Considerazioni sulla sicurezza . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4
Consideraciones sobre seguridad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5
Safety Information (Japan) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6
Safety Information (China) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-7
EMC Regulatory Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-8
U.S.A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-8
Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-8
Australia/New Zealand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-8
Japan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-8
Korea . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-9
Taiwan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-9
European Community . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-10
v
Recycle Statements
Waste Electrical and Electronic Equipment (WEEE) Statements . . . . . . C-1
Index
vi
1
The ProCurve Series 6400cl Switch are multiport switches that can be used to
build high-performance switched workgroup networks. These switches are
store-and-forward devices offering low latency for high-speed networking.
ProCurve Switch 10-Gig CX4 6400cl-6XG (J8433A)
ProCurve Switch 10-Gig 6410cl-6XG (J8474A)
Throughout this manual, this switch will be abbreviated as the Switch 6400cl6XG or Switch 6410cl-6XG and collectively as the Series 6400cl Switch devices.
The Switch 6400cl-6XG and Switch 6410cl-6XG have respectively, six fixed
copper or six flexible media X2 transceiver slots, and one slot is provided in
the back of the device to support a two port 10-Gigabit per second Ethernet
(10-GbE) module to provide box connectivity to other switch boxes, to a
10-GbE concentrator or to any Ethernet compatible uplink.
The Series 6400cl Switch devices can be connected to a ProCurve 600 Redundant and External Power supply (RPS/EPS (J8168A)) and receive full redundant power if the internal power supply in the switch fails. The RPS/EPS unit
will immediately provide all the power necessary to keep the switch running.
1-1
Introducing the Switch
Introducing the Switch
Introducing the Switch
Introducing the Switch
These switches are designed to be used primarily in a high-density wiring
closet or in a data center. These switches can directly connect computers and
servers to provide dedicated bandwidth to those devices, and can build a
switched network infrastructure by connecting the switch to other switches
and routers that support 10-GbE. In addition, the Series 6400cl Switch devices
offer full network management capabilities.
This chapter describes the Series 6400cl Switch devices, including:
■
■
1-2
Front and back of the switches
Switch features
Introducing the Switch
Front of the Switch
Power
and Fault
LEDs
Test, Fan, RPS, and
Module Status LEDs
Auxiliary port
LED
ProCurve Switch 10-Gig 6400cl-6XG (J8433A)
Network ports
Reset and Clear
buttons
Power
and Fault
LEDs
Console port
Test, Fan, RPS, and
Module Status LEDs
Auxiliary port
Auxiliary port
LED
Switch port LEDs
ProCurve Switch 10-Gig 6410cl-6XG (J8474A)
Media Flex X2 transceiver slots
Reset and Clear
buttons
Console port
Auxiliary port
Switch port LEDs
1-3
Introducing the Switch
Front of the Switch
Introducing the Switch
Front of the Switch
Introducing the Switch
Console Port
This port is used to connect a console to the switch by using the serial cable
supplied with the switch. This connection is described under “Connect a
Console to the Switch” in chapter 2, “Installing the Switch.” The console can
be a PC or workstation running a VT-100 terminal emulator, or a VT-100
terminal. The console port is located on the front of both 6400cl devices.
Network Ports
■
Six fixed copper ports or six flexible media X2 transceiver 10-GbE slots.
■
One, 10-GbE expansion slot. These switches provide a single slot in the
back of the device that can accept a 2 by 10-GbE transceiver module. There
are two types of modules:
•
10-GbE Copper cl Module (J8434A) - provides two CX4 fixed copper
ports
•
10-GbE Media-Flex cl Module (J8435A) - provides two flexible media
slots
For more information see the ProCurve Switch cl Modules Installation Guide.
Reset Button
This button is used to reset the switch while it is powered on. This action clears
any temporary error conditions that may have occurred and executes the
switch self test.
Clear Button
This button is used for these purposes:
■
Deleting Passwords - When pressed by itself for at least one second, the
button deletes any switch console access passwords that you may have
configured. Use this feature if you have misplaced the password and need
console access.
This button is provided for your convenience, but its presence means that
if you are concerned with the security of the switch configuration and
operation, you should make sure the switch is installed in a secure
location, such as a locked wiring closet.
The Clear button can also be disabled using a CLI command, see your
“Access Security Guide, the Configuring Font-Panel Security section,”
which is on the Documentation CD-ROM that came with your switch.
1-4
Introducing the Switch
Front of the Switch
■
LEDs
Table 1-1.
Switch LEDs
Switch LEDs
State
Meaning
Power
(green)
On
Off
The switch is receiving power.
The switch is NOT receiving power.
Fault
(orange)
Off
The normal state; indicates there are no fault conditions on the switch.
Blinking*
A fault has occurred on the switch, one of the switch ports, or the fan. The Status LED
for the component with the fault will blink simultaneously.
On
On briefly after the switch is powered on or reset, at the beginning of switch self test.
If this LED is on for a prolonged time, the switch has encountered a fatal hardware
failure, or has failed its self test. See chapter 4, “Troubleshooting” for more information.
Port LEDs
(green – overlaid with the
port number)
Displays port link information and network activity information.
(2 green LEDs)
Link
Indicates the port LEDs are displaying link information:
• if the port LED is on, the port is enabled and receiving a link indication from the
connected device.
• if the port LED is off, the port has no active network cable connected, or is not
receiving link beat or sufficient light. Otherwise, the port may have been disabled
through the switch console, the web browser interface, or ProCurve Manager.
• if the port LED is blinking* simultaneously with the Fault LED, the corresponding port
has failed its self test.
Activity
Indicates the port LEDs are displaying network activity information.
On
Expansion module is plugged into expansion slot and operating correctly
Blinking
Expansion module is plugged into expansion slot but has experienced a fault
Off
Expansion module is not plugged into expansion slot
Mdl (Module
Status, green)
1-5
Introducing the Switch
Restoring Factory Default Configuration - When pressed with the
Reset button in a specific pattern, any configuration changes you may
have made through the switch console, the web browser interface, and
SNMP management are removed, and the factory default configuration is
restored to the switch. For the specific method to restore the factory
default configuration, see “Restoring the Factory Default Configuration”
on page 9, in chapter 4, “Troubleshooting” of this manual.
Introducing the Switch
Introducing the Switch
Front of the Switch
Switch LEDs
State
Meaning
RPS Status
(green)
On
Blinking
Normal operation. RPS is connected and operating correctly. RPS could be powering
the unit - see table below.
RPS is connected but has experienced a fault.
Off
RPS is not connected or is not powered.
Fan Status
(green)
On
Normal operation, all fans are ok.
Blinking*
One of the unit’s fans has failed. The switch Fault LED will be blinking simultaneously.
Test
(green)
Off
The normal operational state; the switch is not undergoing self test.
On
The switch self test and initialization are in progress after the switch has been power
cycled or reset. The switch is not operational until this LED goes off. The Self Test LED
also comes on briefly when you “hot swap” a mini-GBIC into the switch; the mini-GBIC
is self tested when it is hot swapped.
Blinking*
A component of the switch has failed its self test and the switch Fault LED will blink
simultaneously.
On
Port is in use
Off
Port is not in use
Auxiliary
(green)
* The blinking behavior is an on/off cycle once every 1.6 seconds, approximately.
Table 1-2.
RPS LED Behavior
RPS modes
This table describes the behavior of the RPS LED associated with 600 RPS/EPS operation. (Power, RPS/
EPS, Fault)
Power LED
RPS LED
Fault LED
Description
On
Off
Off
Normal operation. 600 RPS/EPS is not connected or not powered.
On
On
Off
Normal operation. 600 RPS/EPS is available.
On
On/Off
Blinking
Unit has experienced a fault and another LED will be blinking to
determine fault.
Off
On
Blinking
600 RPS/EPS is running the switch in failover mode. No AC power to the
unit, or the internal power supply has failed.
Off
Off
Off
Unit is un-powered by AC input line and the external 600 RPS/EPS
On
Blinking
Blinking
The 600 RPS/EPS unit has experienced a fault.
On
Blinking
Off
The 600 RPS/EPS unit is unavailable to power the Switch in event of an
internal power supply failure. The 600 RPS/EPS is designed to provide
power to one of its connected switch devices at a time. The Power
Status LED on the 600 RPS/EPS unit will also be blinking for this device.
1-6
Introducing the Switch
Front of the Switch
Location of Status Indicator LEDs
Status indicator LEDs
Introducing the Switch
Expansion Module LED
ProCurve Switch 6400cl-6XG
Port LED
(one for each port)
ProCurve Switch 6410cl-6XG
Expansion Module LEDs
Status indicator LEDs
Port LED
(one for each port)
■
If the Link indicator LED is lit, each port LED displays link information
for the associated port
■
If the Activity indicator LED is lit, each port LED displays activity
information for the associated port—it flickers as network traffic is
received and transmitted through the port.
1-7
Introducing the Switch
Front of the Switch
Introducing the Switch
Expansion cl Module LEDs
Expansion cl Module LEDs refer to the LEDs specific to the expansion
module. These LEDs are located on the physical expansion module bulkhead.
These LEDs are only viewable in the rear of the Switch on the Expansion
Module itself.
Table 1-3.
Name
Color
Mode
Expansion cl Module LEDs
Description
Expansion Module LEDs per module
Module
Power
(ports A & B)
Green
On
Expansion cl module is plugged into expansion slot and operating
correctly
Off
Expansion cl module's power has been turned OFF, and the card can be
removed from the box if necessary.
Module
Fault
(ports A & B)
Orange
On
Expansion cl module is plugged into expansion slot but has experienced
a fault
Expansion Module LEDs per port
Link
Green
On
Off
Blinking
Activity
Caution
1-8
Green
On
Indicates the port LEDs are displaying link information:
• if the port LED is on, the port is enabled and receiving a link indication
from the connected device.
• if the port LED is off, the port has no active network cable connected,
or is not receiving link beat or sufficient light. Otherwise, the port may
have been disabled through the switch console, the web browser
interface, or ProCurve Manager.
• if the port LED is blinking* simultaneously with the Fault LED, the
corresponding port has failed its self test.
Indicates the port LEDs are displaying network activity information.
It is recommended the power to the switch be removed before inserting or
extracting the expansion module. If the expansion module is inserted or
removed with the switch powered on, a reset will occur. Only install or remove
these modules during scheduled downtime.
Introducing the Switch
Back of the Switch
Introducing the Switch
Back of the Switch
The back of both 6400cl Series switches look the same.
Cooling vents - make sure this is not
obstructed for proper switch operation
Optional cl module slot
ProCurve Series 6400cl Switch
RPS Input Port
AC power connector
cl Module Slot
This switch supports one of two types of cl modules:
■
10-GbE Copper cl Module (J8434A) - provides two CX4 fixed copper ports
■
10-GbE Media-Flex cl Module (J8435A) - provides two flexible media slots
that support a number of different transceivers. See the ProCurve Switch
cl Modules Installation Guide for more information on supported
transceivers.
RPS Input Port
The Series 6400cl Switch supports connectivity to a redundant power supply.
The “ProCurve 600 Redundant and External Power Supply (RPS/EPS)
(J8168A) is an accessory product for the Series 6400cl Switch devices. The
RPS/EPS provides redundant power to any one of up to six switch products,
to back up the power supply in the switch in case of loss of AC power. See
Step 8 of the installation instructions page 2-15 for more information.
Power Connector
The Series 6400cl Switch devices do not have a power switch; they are
powered on when connected to an active AC power source. These switches
automatically adjust to any voltage between 100--240 volts and either 50 or 60
Hz. There are no voltage range settings required.
1-9
Introducing the Switch
Switch Features
Introducing the Switch
Switch Features
The features of the Series 6400cl Switch devices include:
1-10
■
The Switch 6400cl-6XG and Switch 6410cl-6XG have respectively, six fixed
copper or six flexible media X2 transceiver slots, to support 10-GbE
connectivity to other switch boxes, to a 10-GbE concentrator or to any
Ethernet compatible uplink.
■
One slot (optional cl module slot) is provided in the back of the device to
support a series of transceivers to provide box connectivity to other
switch boxes, to a 10-GbE concentrator or to any Ethernet compatible
uplink.
■
One auxiliary port is provided.
■
The Series 6400cl Switch devices can be connected to a ProCurve
RPS/EPS (J8168A) and receive full redundant power if the internal power
supply in the switch fails. The RPS/EPS unit will immediately provide all
the power necessary to keep the switch running.
■
Plug-and-play networking—all ports are enabled—just connect the
network cables to active network devices and your switched network is
operational.
■
Easy management of the switch through several available interfaces:
•
console interface—a full featured, easy to use, VT-100 terminal
interface that is especially good for out-of-band switch management
or for Telnet access to the switch.
•
web browser interface—an easy to use built-in graphical interface
that can be accessed from common web browsers.
•
ProCurve Manager—an SNMP-based, graphical network management tool that you can use to manage your entire network. This
product is included with your new switch.
■
Support for the Spanning Tree Protocol to eliminate network loops.
■
Support for IEEE 802.1Q-compatible VLANs so you can divide the
attached end nodes into logical groupings that fit your business needs.
■
Support for many advanced features to enhance network performance—
for a description, see the Management and Configuration Guide, which
is on the Documentation CD-ROM that is included with your switch.
■
Download of new switch software for product enhancements or bug fixes.
2
Installing the Switch
The ProCurve Series 6400cl Switch devices come with an accessory kit that
includes the brackets for mounting the switch in a standard 19-inch telco rack,
in an equipment cabinet, and with rubber feet that can be attached so the
switch can be securely located on a horizontal surface. The brackets are
designed to allow mounting the switch in a variety of locations and
orientations. This chapter shows how to install the switch.
The Series 6400cl Switch devices have the following components shipped with
them:
■
ProCurve Series 6400cl Switch Installation and Getting Started Guide,
this manual
■
ProCurve Product Documentation CD ROM
(contains PDF file copies of the documentation for the Series 6400cl
Switch devices, including the Management and Configuration Guide,
and for most other ProCurve switches)
■
ProCurve Manager - CD ROM and booklet
■
Read Me First
■
Customer Support/Warranty booklet
■
Console cable
■
Accessory kit (5069-5705)
•
two mounting brackets
•
eight 8-mm M4 screws to attach the mounting brackets to the switch
•
four 5/8-inch number 12-24 screws to attach the switch to a rack
•
four rubber feet
2-1
Installing the Switch
Included Parts
Installing the Switch
Included Parts
■
Power cord, one of the following:
Australia/New Zealand
China
Continental Europe
Denmark
Japan
Switzerland
United Kingdom/Hong Kong/Singapore
United States/Canada/Mexico
8120-6803
8120-8377
8120-6802
8120-6806
8120-6804
8120-6807
8120-8709
8120-6805
Installing the Switch
Japan Power
Cord Warning
Please use the power cord supplied with your product. This power cord
is not to be used with other products.
2-2
Installing the Switch
Installation Procedures
Installation Procedures
Summary
1.
Prepare the installation site (page 2-5). Ensure the physical environment is properly prepared, including having the correct network cabling
ready to connect to the switch and having an appropriate location for the
switch. See page 2-4 for some installation precautions.
2. Install a cl module (optional—page 2-7).
4.
Verify the switch passes self test (page 2-9). Plug the switch into a
power source and observe that the LEDs on the switch’s front panel
indicate correct switch operation. When self test is complete, unplug the
switch.
5.
Mount the switch (page 2-11). The Switch can be mounted in a 19-inch
telco rack, in an equipment cabinet, or on a horizontal surface.
6.
Connect power to the switch (page 2-13). Once the switch is mounted,
plug it into the nearby main power source.
7.
Connect the network cables (page 2-14). Using the appropriate
network cables, connect the network devices to the switch ports.
8.
Connect a Redundant Power Supply (RPS), (optional—page 2-15).
You may wish to use the RPS option with your Switch. Connect the RPS
using the cables supplied with the RPS, to the back of the switch.
9.
Connect a console to the switch (optional—page 2-18). You may wish
to modify the switch’s configuration, for example, to configure an IP
address so it can be managed using a web browser, from an SNMP network
management station, or through a Telnet session. Configuration changes
can be made easily by using the included console cable to connect a PC
to the switch’s console port.
At this point, the switch is fully installed. See the rest of this chapter if you
need more detailed information on any of these installation steps.
2-3
Installing the Switch
3. Install a transceiver (optional—page 2-8). If you have installed a media
flex cl module, you can now install one or two transceivers.
Installing the Switch
Installation Procedures
Installation Precautions:
Follow these precautions when installing the Series 6400cl Switch devices.
Installing the Switch
WARNING
Cautions
■
The rack or cabinet should be adequately secured to prevent it
from becoming unstable and/or falling over. Devices installed in a
rack or cabinet should be mounted as low as possible, with the
heaviest devices at the bottom and progressively lighter devices
installed above.
■
For safe operation, do not install the switch with the back face of
the switch (with the fan vents) facing either downward or upward.
■
Left side vents cannot be placed downward. (That is, the left side
of the unit while facing the front.)
■
For safe operation, use only screws provided with your rack mount
kit to secure mounting brackets to the switch. Use of longer or
improper screws may damage internal components
■
Ensure the power source circuits are properly grounded, then use the
power cord supplied with the switch to connect it to the power source.
■
If your installation requires a different power cord than the one supplied
with the switch, be sure to use a power cord displaying the mark of the
safety agency that defines the regulations for power cords in your country.
The mark is your assurance that the power cord can be used safely with
the switch.
■
When installing the switch, the AC outlet should be near the switch and
should be easily accessible in case the switch must be powered off.
■
Ensure the switch does not overload the power circuits, wiring, and overcurrent protection. To determine the possibility of overloading the supply
circuits, add together the ampere ratings of all devices installed on the
same circuit as the switch and compare the total with the rating limit for
the circuit. The maximum ampere ratings are usually printed on the
devices near the AC power connectors.
■
Do not install the switch in an environment where the operating ambient
temperature might exceed 55°C (131°F)1.
■
Ensure the air flow around the sides and back of the switch is not
restricted.
■
For safe operation, proper switch cooling, and reduction of electromagnetic emissions, ensure a slot cover is installed on any unused module slot.
1
If you are installing either of the Series 6400cl Switch devices using one of the fiber transceivers,
the operating ambient temperature should not exceed 40°C (104°F). See transceiver
specifications in the ProCurve Switch cl Modules Installation Guide.
2-4
Installing the Switch
Installation Procedures
1. Prepare the Installation Site
Cabling Infrastructure - Ensure the cabling infrastructure meets the
necessary network specifications. The copper ports accept CX4 cable with
Infiniband-style connectors or fiber cable using a CX4 optical media converter
(OMC). The fiber ports accept single-mode fiber optic cable with SC
connectors.
Table 2-1.
Fiber-Optic Cables
Cable Specifications
Connector
Type
Supported Length
10-GbE SR
Multimode fiber-optic cable designed for Gigabit
Ethernet: 62.5/125 µm (core/cladding) diameter
or 50/125 µm, low metal content, complying with
the ITU-T G.652 and ISO/IEC 793-2 Type B1
standards. 1
SC
10-GbE LR
9/125 µm (core/cladding) diameter, low metal
content, single mode fiber-optic cables,
complying with the ITU-T G.652 and ISO/IEC 7932 Type B1 standards. 1,2
SC
single-mode cable: 2 meters - 10 km
10-GbE ER
9/125 µm (core/cladding) diameter, low metal
content, single mode fiber-optic cables,
complying with the ITU-T G.652 and ISO/IEC 7932 Type B1 standards. 1,2
SC
single-mode cable: 2 meters - 30 km (40
kilometers, on an engineered fiber optic
link that meets standards in the
specification).
■
■
OMC CX4 Fiber 12 fiber 50/125 µm (core/cladding) diameter,
multimode Fiber ribbon cable. 12 fiber 62.5/125
µm (core/cladding) diameter, multimode Fiber
ribbon cable is also supported. 1
MTP
62.5 µm cable:
•
160 Mhz*km = 2-26 meters
•
200 Mhz*km = 2-33 meters
50 µm cable:
•
400 Mhz*km = 2-66 meters
•
500 Mhz*km = 2-82 meters
•
2000 Mhz*km = 2-300 meters
1-300 meters
1 Conditioning patch cord cables are not supported.
2 Multimode cables are not supported
Table 2-2.
Copper Cables
Port Type
Cable Specifications
Connector
Type
Supported Length
CX4
Speed 3.125Gbx4
(Cables compatible with the 802.1ak standard)
CX4
0.5-15 meters
Infinibandstyle
2-5
Installing the Switch
Port Type
Installing the Switch
Installation Procedures
Installing the Switch
■
2-6
Installation Location - Before installing the switch, plan its location and
orientation relative to other devices and equipment:
•
In the front of the switch, leave at least 7.6 cm (3 inches) of space for
the twisted-pair and fiber-optic cabling.
•
In the back of the switch, leave at least 10.16 cm (4 inches) of space
for the cl module cabling.
•
On the sides of the switch, leave at least 7.6 cm (3 inches) for cooling,
except if the switch is installed in an open EIA/TIA rack.
Installing the Switch
Installation Procedures
2. (Optional) Install or Remove a cl Module
Caution
It is recommended the power to the switch be removed before inserting or
extracting the expansion module. If the expansion module is inserted or
removed with the switch powered on, a reset will occur. Only install or remove
these modules during scheduled downtime.
1.
Remove the cover plate
Align the edges of the board with guides
Installing the Switch
Extractor Handles
2.
Insert the module aligning with the guides in the slot.
3.
Once the contacts have engaged, use the extractor handles to seat the
module completely.
4.
Tighten the captive screws.
Refer to the ProCurve Switch cl Modules Installation Guide for more details.
If you have installed a media flex module, you can now install a transceiver.
See the following step.
2-7
Installing the Switch
Installation Procedures
3. (Optional) Install or Remove a Transceiver
WARNING
The ProCurve X2 fiber optic transceivers are Class 1 or Class 1M laser
devices. Avoid direct eye exposure to the beam coming from the
transmit port.
Installing the Switch
a. Slide the transceiver in until it stops.1
1
If you are installing either of the Series 6400cl Switch devices using a fiber transceiver,
the operating ambient temperature should not exceed 40°C (104°F). See transceiver
specifications in the ProCurve Switch cl Modules Installation Guide.
b. Push firmly until the gasket seats against the bulkhead.
Bail
Note
When switch power is on, the Link and Activity LEDs will come on for
approximately two seconds and then go off. This is confirmation the
transceiver is installed and seated correctly.
c. If your transceiver has a bail, move the bail up, if not your transceiver is
now completely installed. Refer to the ProCurve Switch cl Module
Installation Guide for more details.
To remove the transceiver:
If your transceiver has a bail, lower the bail until it is approximately horizontal,
and then using the bail, pull the transceiver from the slot. If your transceiver
does not have a bail, pull the transceiver straight out.
2-8
Installing the Switch
Installation Procedures
4. Verify the Switch Passes Self Test
Before mounting the switch in its network location, you should first verify it
is working properly by plugging it into a power source and verifying it passes
self test.
1.
Connect the power cord supplied with the switch to the power connector
on the back of the switch, and then into a properly grounded electrical
outlet.
Installing the Switch
Connect power cord
to the power
connector
Note
The Series 6400cl Switch devices do not have a power switch. They are
powered on when the power cord is connected to the switch and to a power
source. For safety, the power outlet should be located near the switch
installation.
The switch automatically adjusts to any voltage between 100-240 volts and
either 50 or 60 Hz. No voltage range settings are required.
If your installation requires a different power cord than the one supplied with
the switch, be sure to use a power cord displaying the mark of the safety
agency that defines the regulations for power cords in your country. The mark
is your assurance that the power cord can be used safely with the switch.
2-9
Installing the Switch
Installation Procedures
Installing the Switch
2.
Power and
Fault LEDs
Power and
Fault LEDs
Check the LEDs on the switch as described below.
Switch port LEDs
ProCurve Switch 6400cl-6XG
Switch port LEDs
ProCurve Switch 6410cl-6XG
Test LED
Test LED
When the switch is powered on, it performs a diagnostic self test. Self test
takes approximately 50 seconds to complete.
LED Behavior:
During the self test:
2-10
•
Initially, all the status and port LEDs are on for most of the duration
of the test.
•
Most of the LEDs go off and then may come on again during phases
of the self test. For the duration of the self test, the Test LED stays on.
Installing the Switch
Installation Procedures
When the self test completes successfully:
•
The Power and Fan Status LEDs remain on.
•
The Fault and Test LEDs go off.
•
The port LEDs (includes the expansion module LEDs) go into their
normal operational mode:
– If the ports are connected to active network devices, the LEDs
behave according to their function, Link or Activity.
– If the ports are not connected to active network devices, the LEDs
will stay off.
3.
After the self test has completed successfully disconnect the power cord
in preparation for mounting the switch.
5. Mount the Switch
After the switch passes self test, you are ready to mount the switch in a stable
location. The Series 6400cl Switch devices can be mounted in these ways:
■
■
in a rack or cabinet
on a horizontal surface
Rack or Cabinet Mounting
The Series 6400cl Switch devices are designed to be mounted in any EIAstandard 19-inch telco rack or communication equipment cabinet.
WARNING
For safe operation, please read the installation precautions on
page 2-4, before mounting a switch.
Equipment
Cabinet
Note
The 12-24 screws supplied with the switch are the correct threading for
standard EIA/TIA open 19-inch racks. If you are installing the switch in an
equipment cabinet such as a server cabinet, use the clips and screws that came
with the cabinet in place of the 12-24 screws that are supplied with the switch.
Complete step 1, and plan which four holes you will be using in the cabinet
and install all four clips. Then proceed to step 2.
2-11
Installing the Switch
If the LED display is different than what is described above, especially if
the Fault and Test LEDs stay on for more than 60 seconds or they start
blinking, the self test has not completed correctly. Refer to chapter 4,
“Troubleshooting” for diagnostic help.
Installing the Switch
Installation Procedures
Rack Mounting the Series 6400cl Switch Devices
WARNING
For safe operation, use only screws provided with your rack mount kit
to secure mounting brackets to the switch. Use of longer or improper
screws may damage internal components
Installing the Switch
1.
Use a #1 Phillips (cross-head) screwdriver and attach the mounting
brackets to the switch with the included 8-mm M4 screws.
8 mm
M4 screws
Note
2-12
The mounting brackets have multiple mounting holes and can be rotated
allowing for a wide variety of mounting options. These include mounting the
switch so its front face is flush with the face of the rack (as in the illustration
above), or mounting it in a more balanced position.
Installing the Switch
Installation Procedures
2.
Hold the switch with attached brackets up to the rack and move it
vertically until rack holes line up with the bracket holes, then insert and
tighten the four number 12-24 screws holding the brackets to the rack.
Installing the Switch
Horizontal Surface Mounting
Place the switch on a table or other horizontal surface. The switch comes with
rubber feet in the accessory kit that can be used to help keep the switch from
sliding on the surface.
Attach the rubber feet to the four corners on the bottom of the switch within
the embossed angled lines. Use a sturdy surface in an uncluttered area. You
may want to secure the networking cables and switch power cord to the table
leg or other part of the surface structure to help prevent tripping over the
cords.
Caution
Make sure the air flow is not restricted around the sides and back of the switch.
6. Connect the Switch to a Power Source
1.
Plug the included power cord into the switch’s power connector and into
a nearby AC power source.
2.
Re-check the LEDs during self test. See “LED Behavior” on page 2-10
2-13
Installing the Switch
Installation Procedures
7. Connect the Network Cables
Connect the network cables, described under “Cabling Infrastructure”
(page 2-5), from the network devices or your patch panels to the fiber or
copper ports on the switch.
Connecting a fiber cable
To connect:
1. Remove the dust covers from
the cable connectors and the
port.
Installing the Switch
2. Aligning the notches on the
cable connectors with the slots
of the port, press the cable
connector into the port until it
snaps into place.
1
2
If the Link LED does not go on
when the network cable is
connected to the port, see
“Diagnosing with the LEDs” on page 4-3, in chapter 4, “Troubleshooting”.
To disconnect:
Pull the cable connector straight out.
Connecting a copper cable
To connect:
1. Push the copper cable
connector into the copper port.
Ensure the locking device locks
the cable connector into place.
To disconnect:
Pull the cable connector straight
out.
When a network cable from an
active network device is connected
to the port, the port LED for that
port should go on. If the port LED
does not go on when the network cable is connected to the port, see
“Diagnosing with the LEDs” on page 4-3 in chapter 4, “Troubleshooting”.
2-14
Installing the Switch
Installation Procedures
8. (Optional) Connect a Redundant Power Supply to the
Switch
The “ProCurve 600 Redundant and External Power Supply (hereafter referred
to as the RPS/EPS)” (J8168A) is an accessory product for the Series 6400cl
Switch devices and specific other ProCurve switches. The RPS/EPS provides
redundant power to any one of up to six switch products, to back up the power
supply in the switch in case of loss of AC power, or a fault condition. The RPS/
EPS is an unmanaged power supply that only provides information by way of
LEDs or through the port interfaces to attached devices.
Operating Characteristics
Connect the RPS/EPS to the switch using one of the 6 supplied RPS cables.
Pin 1 Markings
2-15
Installing the Switch
The RPS/EPS has six connectors, each of which can provide redundant +12V
power to a connected switch, but only one connector can provide this power
at a given time. If a switch with no AC power is connected to an operating
RPS/EPS, it will NOT immediately power up this new switch. Power can only
be provided to a switch if it is first powered on and operating correctly. Then
when the power to the switch fails, power will be provided from the RPS/EPS,
if it is available, that is, if the RPS/EPS is not already providing power to a
higher priority switch. If two or more devices fail, priority goes to the device
plugged into the lower numbered port on the RPS/EPS unit. Consequently the
most important switch must be plugged into port one on the RPS/EPS. In this
state, the “Connected” LED should be ON, and the “Power Status” LED should
be BLINKING. (Refer to the documentation that came with your RPS/EPS.)
Installing the Switch
Installation Procedures
LEDs
The RPS LEDs are located on the back of the RPS/EPS. These LEDs are
duplicated on the front of the device. The following graphic shows an example
of the back of the RPS/EPS. There are two green LEDs for each RPS port:
■
Device Connected
■
Power Status
! RPS Power: 12V
Installing the Switch
RPS 1
Device Connected R1
Power Status
ProCurve 600 RPS/EPS
(J8168A)
Power Status LED
Device Connected LED
RPS 2
R2
backup to one connected device. Lowest-numbered port has priority.
RPS 3
R3
RPS 4
R4
The following states provide status of an RPS/EPS port.
2-16
Fault
Device
Connected
Power
Status
Message
Off
Off
Off
Nothing Connected
On or Off
Off
On
Not a valid state - should never happen
Off
On
Off
Switch is connected, RPS is available but
not required
Off
On
On
RPS is powering the connected device
Blinking
Off
Blinking
RPS port is in fault mode
Off
On
Blinking
Switch is requesting power, RPS can not
provide it
Blinking
On
Off
Switch is unplugged, but RPS is powering
switch
Installing the Switch
Installation Procedures
The following picture demonstrates and example of connectivity between an
RPS/EPS device and a Switch device.
Switch 6400cl device,
RPS input port
RPS Power: 12V
Device Connected R1
Power Status
RPS 2
R2
RPS 3
backup to one connected device. Lowest-numbered port has priority.
R3
RPS 4
EPS Power: 50V
R4
RPS 5
R5
RPS 6
R6
EPS 1
370W total for PoE applications. Power is shared when
E1
both ports are used.
Device
EPS 2
E2 Connected
Power
Status
Line: 50/60 Hz.
40 V~ 9.1A (9,1A)
-2
0
10
RPS output port
RPS/EPS Operation
The RPS/EPS monitors the power signal from the switch by detecting that the
RPS/EPS is connected to a switch with an RPS/EPS cable. When the power
from the switch is no longer detected, the RPS/EPS will turn on and provide
power to the switch within 1ms.
The RPS/EPS supports hot plugging of the RPS/EPS cable without causing a
reboot of the switch or causing the power supply in either the RPS/EPS or
switch to shut down temporarily or permanently. For more information refer
to the documentation that came with the RPS/EPS.
2-17
Installing the Switch
RPS 1
Installing the Switch
Installation Procedures
9.(Optional) Connect a Console to the Switch
The switch has a full-featured, easy to use console interface for performing
switch management tasks including the following:
■
Monitor switch and port status and observe network activity statistics
■
Modify the switch’s configuration to optimize switch performance,
enhance network traffic control, and improve network security
■
Read the event log and access diagnostic tools to help in troubleshooting
■
Download new software to the switch
■
Add passwords to control access to the switch from the console, web
browser interface, and network management stations
Installing the Switch
The console can be accessed through these methods:
■
Out-of-band: The switch comes with a serial cable for connecting a PC
or VT-100 terminal, to be used as a console, directly to the switch.
■
In-Band: Access the console using Telnet from a PC or UNIX station on
the network, and a VT-100 terminal emulator. This method requires that
you first configure the switch with an IP address and subnet mask by using
either out-of-band console access or through DHCP/Bootp. For more
information on IP addressing and on starting a Telnet session, see
chapter 3, “Getting Started With Switch Configuration”, and the Management and Configuration Guide, which is on the Documentation CD-ROM
that came with your switch.
The Switch can simultaneously support one out-of-band console session
through the Console Port and one in-band Telnet console session.
Terminal Configuration
To connect a console to the switch, configure the PC terminal emulator as a
DEC VT-100 (ANSI) terminal or use a VT-100 terminal, and configure either
one to operate with these settings:
■
any baud rate from 1200 to 115200 (the switch senses the speed)
■
8 data bits, 1 stop bit, no parity, and flow control set to Xon/Xoff
■
For the Windows Terminal program, also disable (uncheck) the “Use
Function, Arrow, and Ctrl Keys for Windows” option
■
For the Hilgraeve HyperTerminal program, select the “Terminal keys”
option for the “Function, arrow, and ctrl keys act as” parameter.
If you want to operate the console using a different configuration, make sure
you change the settings on both the terminal and on the switch so they are
compatible. Change the switch settings first, save your changes, then change
the terminal settings, then reboot the switch and reestablish the console
session.
2-18
Installing the Switch
Installation Procedures
Direct Console Access
To connect a console to the
switch, follow these steps:
1.
3.
Turn on the terminal or
PC’s power and, if using a
PC, start the PC terminal
program.
Console port
Console cable supplied
with the switch
Installing the Switch
2.
Connect the PC or
terminal to the switch’s
Console Port using the
console cable included
with the Switch. (If your
PC or terminal has a 25-pin
serial connector, first
attach a 9-pin to 25-pin
straight-through adapter
at one end of the console
cable.)
PC running a terminal
emulator program, or
a VT-100 terminal
Press [Enter] two or three
times and you will see the
copyright page and the message “Press any key to continue”. Press a key,
and you will then see the switch console command (CLI) prompt, for
example:
ProCurve Switch 6400cl-6XG#
If you want to continue with console management of the switch at this time,
see chapter 3, “Getting Started With Switch Configuration” for some basic
configuration steps. For more detailed information, refer to the Management
and Configuration Guide, which is on the Documentation CD-ROM that came
with the switch.
2-19
Installing the Switch
Sample Network Topologies
Sample Network Topologies
This section shows a few sample network topologies in which the Switch is
implemented. For more topology information, see the ProCurve Networking
products Web site, http://www.procurve.com.
Installing the Switch
Three Tier Model
Server with 10-Gigabit
Ethernet NIC
ProCurve Switch 6400cl
ProCurve Switch 3400cl-24G
10-Gigabit Ethernet cable
ProCurve Switch 3400cl-48G
Fast Ethernet
PCs, local servers,
and peripherals
The Switch is designed to be used primarily in a wiring closet or in the data
center as a distribution, high speed (10-GbE) switch to which edge switches
supporting 10-GbE speeds (such as the ProCurve Switch 3400cl Series) would
be connected using fiber or copper cables. The end nodes, printers and other
peripherals, are then connected to the edge switch. The end node devices are
connected to the edge switch by straight-through or crossover twisted-pair
cables. Either cable type can be used because of the “IEEE Auto MDI/MDI-X”
features on the Switch.
2-20
Installing the Switch
Sample Network Topologies
Remote Campus
Main Office Data Center
6400cl
Local Site using 10-GbE SR or
OMC up to 300m
6410cl
Installing the Switch
Remote Site using 10-GbE
LR up to 10 km
Remote Site using 10-GbE
LR up to 10 km
6400cl
6400cl
2-21
Installing the Switch
Sample Network Topologies
Flexible Stacking
The Series 6400cl Switch devices can be connected together in two
configurations depending on your need:
High performance stack
Installing the Switch
This configuration provides:
■
228 gigabit ports
■
4.8 to 1 over-subscription
In this configuration each 3400cl switch is connected separately to it’s own
port on the 6400cl providing 10-GbE connectivity to the 6400cl switch and the
6400cl switch is connected to the core using 10-GbE as well.
This topology also demonstrates an example of incorporating the use of a
redundant power supply to support the 3400cl switches.
ProCurve Switch 6400cl
To Core
ProCurve 600 RPS/EPS
ProCurve Switch 3400cl
10-GbE Cables
2-22
Power Cables
Installing the Switch
Sample Network Topologies
Resiliency Using 6400cl Series as a meshed Cluster
The redundant topology increases the availability of a single switch by
protecting against single points of failure. All hardware and paths are
redundant and active (versus, Spanning Tree Blocking). If any hardware
failure occurs, I/O communications can still be completed through another
path.
To Server or other
Switches (Not
meshed ports)
To Server or other
Switches (Not
meshed ports)
Installing the Switch
ProCurve Switch 6400cl
ProCurve Switch 3400cl
10-GbE Cables
10-GbE Cables
2-23
3
Getting Started With Switch Configuration
This chapter is a guide for using the console Switch Setup screen to quickly
assign an IP (Internet Protocol) address and subnet mask to the switch, set a
Manager password, and, optionally, configure other basic features.
For more information on using the switch console and the other switch
management interfaces: the web browser interface and the SNMP management tool, ProCurve Manager, please see the Management and Configuration
Guide, which is on the Documentation CD-ROM that came with your switch.
Recommended Minimal Configuration
Many other features can be configured through the switch’s console interface,
to optimize the switch’s performance, to enhance your control of the network
traffic, and to improve network security. Once an IP address has been configured on the switch, these features can be accessed more conveniently through
a remote Telnet session, through the switch’s web browser interface, and from
an SNMP network management station running a network management
program, such as ProCurve Manager. For a listing of switch features available
with and without an IP address, refer to “How IP Addressing Affects Switch
Operation” in the Management and Configuration Guide, which is on the
Documentation CD-ROM that came with your switch.
For more information on IP addressing, refer to “IP Configuration” in the
Management and Configuration Guide.
3-1
Getting Started With Switch
Configuration
In the factory default configuration, the switch has no IP (Internet Protocol)
address and subnet mask, and no passwords. In this state, it can be managed
only through a direct console connection. To manage the switch through inband (networked) access, you should configure the switch with an IP address
and subnet mask compatible with your network. Also, you should configure
a Manager password to control access privileges from the console and web
browser interface. Other parameters in the Switch Setup screen can be left at
their default settings or you can configure them with values you enter.
Getting Started With Switch Configuration
Note
By default, the switch is configured to acquire an IP address configuration
from a DHCP or Bootp server. To use DHCP/Bootp instead of the manual
method described in this chapter, see “DHCP/Bootp Operation” in the
Management and Configuration Guide, which is on the Documentation
CD-ROM that came with your switch.
Using the Console Setup Screen
The quickest and easiest way to minimally configure the switch for management and password protection in your network is to use a direct console
connection to the switch, start a console session, and access the Switch Setup
screen.
1.
Using the method described in the preceding section, connect a terminal
device to the switch and display the switch console command (CLI)
prompt (the default display).
The CLI prompt appears displaying the switch model number:
ProCurve Switch 6400cl-6XG#
2.
At the prompt, enter the setup command to display the Switch Setup
screen. The following illustration shows the Setup screen with the default
settings.
Getting Started With Switch
Configuration
6400cl-6xg
6400cl-6xg
3.
3-2
Use the [Tab] key to select the Manager Password field and enter a manager
password of up to 16 characters.
Getting Started With Switch Configuration
[Tab] to the IP Config (DHCP/Bootp) field and use the Space bar to select the
4.
Manual option.
5.
[Tab] to the IP Address field and enter the IP address that is compatible with
your network.
6.
[Tab] to the Subnet Mask field and enter the subnet mask used for your
network.
7.
Press [Enter], then [S] (for Save).
Here is some information on the fields in the Setup screen. For more information on these fields, see the Management and Configuration Guide, which is
on the Documentation CD-ROM that came with your switch:
Parameter
Default
blank
Optional; up to 25 characters, including spaces
System Contact
blank
Optional; up to 48 characters, including spaces
Manager Password
blank
Recommended; up to 16 characters (no blank spaces)
Logon Default
CLI
The default setting selects the command line interface for console access.
The alternative is the menu interface.
Time Zone
0 (none)
Optional; 1440 to -1440. The number of minutes your location is to the West (-)
or East (+) of GMT.
Community Name
public
Default setting recommended.
Spanning Tree Enabled
No
Default setting recommended unless STP is already running on your network
or the switch will be used in complex network topologies.
Default Gateway
blank
Optional; Enter the IP address of the next-hop gateway node if network traffic
needs to be able to reach off-subnet destinations.
Time Sync Method
None
Optional; The protocol the switch uses to acquire a time signal. The options
are SNTP and TimeP.
TimeP Mode
Disabled
Optional; The method the switch uses to acquire the TimeP server address.
IP Config (DHCP/Bootp)
DHCP/Bootp
Set to Manual unless a DHCP/Bootp server is used on your network to
configure IP addressing.
IP Address
xxx.xxx.xxx.xxx Recommended; If you set IP Config to Manual, then enter an IP address
compatible with your network.
Note: The IP address and subnet mask assigned for the switch must be compatible with the IP addressing used in
your network. For more information on IP addressing, see the Management and Configuration Guide, which is on the
Documentation CD-ROM that came with your switch.
Subnet Mask
xxx.xxx.xxx.xxx Recommended; If you entered an IP address, then enter a subnet mask
compatible with your network.
3-3
Getting Started With Switch
Configuration
System Name
Getting Started With Switch Configuration
Where to Go From Here
The above procedure configures your switch with a Manager password, IP
address, and subnet mask. As a result, with the proper network connections,
you can now manage the switch from a PC equipped with Telnet, a web
browser interface, or from an SNMP-based network management station
using a tool such as ProCurve Manager.
Some basic information on managing your switch is included in the next
section. For more information on the console, web browser, and SNMP
management interfaces and all the features that can be configured on the
Switch 6400, please see the Management and Configuration Guide, which is
on the Documentation CD-ROM that came with your switch.
Getting Started With Switch
Configuration
To Recover from a Lost Manager Password: If you cannot start a console session at the manager level because of a lost Manager password, you
can clear all passwords and user names by getting physical access to the
switch and pressing and holding the Clear button for a full second.
3-4
Getting Started With Switch Configuration
Using the IP Address for Remote Switch Management
Using the IP Address for Remote Switch
Management
With your Switch 6400, you can use the switch’s IP address to manage the
switch from any PC that is on the same subnet as the switch. You can use either
a Telnet session or a standard web browser to manage the switch.
Starting a Telnet Session
To access the switch through a Telnet session, follow these steps:
1.
Make sure the switch is configured with an IP address and that the switch
is reachable from the PC that is running the Telnet session (for example,
by using a Ping command to the switch’s IP address).
2.
Start the Telnet program on a PC that is on the same subnet as the switch
and connect to the switch’s IP address.
3.
You will see the copyright page and the message “Press any key to
continue”. Press a key, and you will then see the switch console command
(CLI) prompt, for example:
Enter help or ? to see a list of commands that can be executed at the
prompt. Entering any command followed by help provides more detailed
context help information about the command. Entering any command
followed by ? displays a list of options that are available at that point in
the command entry.
Starting a Web Browser Session
Your Switch 6400 can be managed through a graphical interface that you can
access from any PC or workstation on the network by running your web
browser and typing in the switch’s IP address as the URL. No additional
software installation is required to make this interface available; it is included
in the switch’s onboard software.
3-5
Getting Started With Switch
Configuration
ProCurve Switch 6400cl#
Getting Started With Switch Configuration
Using the IP Address for Remote Switch Management
The operating systems, web browsers, and Java support required to manage
the switch through the browser interface are listed in the following table:
Operating System
Internet Explorer
Java Version
Windows 2000 SP4
5.5 SP2, 6.0 SP1
1.3.1_12 and 1.4.2_05
Windows XP SP1a
6.0 SP1
1.3.1_12 and 1.4.2_05
Windows Server 2003
6.0 SP1
1.3.1_12 and 1.4.2_05
A typical web browser interface screen is shown in the next illustration.
Getting Started With Switch
Configuration
Procur ve Sw itch 6 400cl-6xg
G- S ta tus: Inf orm a tion
J8433A Pr ocur ve Sw itch 6 400cl-6xgG
For more information on using the web browser interface, please see the
Management and Configuration Guide, which is on the Documentation
CD-ROM that came with your switch.
An extensive help system is also available for the web browser interface. To
access the help system though, the subnet on which the switch is installed
must have access to the internet, or ProCurve Manager needs to be installed
on a network management station that is on the subnet.
3-6
4
Troubleshooting
This chapter describes how to troubleshoot your switch. This document
describes troubleshooting mostly from a hardware perspective. You can
perform more in-depth troubleshooting on the switch using the software tools
available with the switch, including the full-featured console interface, the
built-in web browser interface, and ProCurve Manager, the SNMP-based
network management tool. For more information, see the chapter “Troubleshooting” in the Management and Configuration Guide, which is on the
Documentation CD-ROM that came with your switch.
This chapter describes the following:
■
basic troubleshooting tips (page 4-1)
■
diagnosing with the LEDs (page 4-3)
■
Proactive Networking tools (page 4-6)
■
hardware diagnostic tests (page 4-7)
■
restoring the factory default configuration (page 4-9)
■
downloading new software to the Switch 6400 (page 4-10)
■
ProCurve Customer Support Services (page 4-11)
Basic Troubleshooting Tips
Most problems are caused by the following situations. Check for these items
first when starting your troubleshooting:
Faulty or loose cables. Look for loose or obviously faulty connections.
If they appear to be OK, make sure the connections are snug. If that does
not correct the problem, try a different cable.
■
Non-standard cables. Non-standard and miswired cables may cause
network collisions and other network problems, and can seriously impair
network performance. Use a new correctly-wired cable or compare your
cable to the cable in appendix B, “Cables and Connectors” for pinouts and
correct cable wiring.
4-1
Troubleshooting
■
Troubleshooting
Basic Troubleshooting Tips
■
Improper Network Topologies. It is important to make sure you have
a valid network topology. Common topology faults include excessive
cable length and excessive repeater delays between end nodes. If you have
network problems after recent changes to the network, change back to
the previous topology. If you no longer experience the problems, the new
topology is probably at fault. Sample topologies are shown at the end of
chapter 2 in this book, and some topology configuration guidelines can
be found online at the ProCurve Networking Web site,
http://www.procurve.com.
In addition, you should make sure that your network topology contains
no data path loops. Between any two end nodes, there should be only
one active cabling path at any time. Data path loops will cause broadcast
storms that will severely impact your network performance.
For your switch, if you wish to build redundant paths between important
nodes in your network to provide some fault tolerance, you should enable
Spanning Tree Protocol support on the switch. This ensures only one
of the redundant paths is active at any time, thus avoiding data path loops.
Spanning Tree can be enabled through the switch console, the web
browser interface, or ProCurve Manager.
The Series 6400cl Switch devices also support Trunking, which allows
multiple network cables to be used for a single network connection
without causing a data path loop. For more information on Spanning Tree
and Trunking, see the Management and Configuration Guide, which is
on the Documentation CD-ROM that came with your switch.
■
Check the port configuration. A port on your switch may not be
operating as you expect because it has been put into a “blocking” state by
Spanning Tree, meshing, or LACP (automatic trunking). (Note that the
normal operation of the Spanning Tree, meshing, and LACP features may
put the port in a blocking state.) Or, the port just may have been configured
as disabled through software.
Troubleshooting
Use the switch console to determine the port’s configuration and verify
that there is not an improper or undesired configuration of any of the
switch features that may be affecting the port. For more information, see
the Management and Configuration Guide, which is on the Documentation CD-ROM that came with your switch.
For more information on possible network problems and their solutions, refer
to the technical note “Troubleshooting LAN Performance and Intermittent
Connectivity Problems”, which can be found on the ProCurve Networking
Web site, http://www.procurve.com, in the Information Library section.
4-2
Troubleshooting
Diagnosing with the LEDs
Diagnosing with the LEDs
Table 4-1 shows LED patterns on the switch and the switch modules that
indicate problem conditions.
1.
Check in the table for the LED pattern you see on your switch.
2.
Refer to the corresponding diagnostic tip on the next few pages.
Table 4-1.
LED Error Indicators
LED Pattern Indicating Problems
Module
(Mdl)
Status/
Fault**
RPS
Status
Fan
Status
Port LED
Test
(Link)
Diagnostic
Tips
*
*
*
*
*
*
➊
On
Prolonged On
*
*
Prolonged On
*
*
➋
On
Blinking†
*
*
Blinking†
*
*
➌
On
Blinking†
*
*
Off
Blinking†
*
➍
On
Blinking†
See tip 5
*
Blinking†
*
Blinking†
➎
On
Off
*
*
Off
*
Off with cable
connected
➏
On
Off
*
*
Off
*
On, but the port is not
communicating
➐
On
Blinking†
*
On
*
*
*
➑
On
Blinking†
F1 Blinking†
B2 Blinking†
*
Blinking†
*
*
➒
Power
Fault
Off with
power cord
plugged in
Troubleshooting
* This LED is not important for the diagnosis.
† The blinking behavior is an on/off cycle once every 1.6 seconds, approximately.
** The Module Fault LED is located on the module in the rear of the switch.
1 F - Front
2 B - Back
4-3
Troubleshooting
Diagnosing with the LEDs
Diagnostic Tips:
Problem
Solution
➊
The switch is not
plugged into an
active AC power
source, or the
switch’s power
supply may have
failed.
1. Verify the power cord is plugged into an active power source and to the switch. Make
sure these connections are snug.
2. Try power cycling the switch by unplugging and plugging the power cord back in.
3. If the Power LED is still not on, verify that the AC power source works by plugging
another device into the outlet. Or try plugging the switch into a different outlet or try a
different power cord.
If the power source and power cord are OK and this condition persists, the switch power
supply may have failed. Call your ProCurve authorized LAN dealer, or use the electronic
support services from ProCurve to get assistance. See the Customer Support/Warranty
booklet for more information.
➋
A switch
hardware failure
has occurred. All
the LEDs will stay
on indefinitely.
Try power cycling the switch. If the fault indication reoccurs, the switch may have failed.
Call your ProCurve authorized LAN dealer, or use the electronic support services from
ProCurve to get assistance. See the Customer Support/Warranty booklet for more
information.
➌
The switch has
experienced a
software failure
during self test.
1. Try resetting the switch by pressing the Reset button on the front of the switch, or by
power cycling the switch.
2. If the fault indication reoccurs, attach a console to the switch (as indicated in chapter
2) and configure it to operate at 9600 baud. Then, reset the switch. Messages should
appear on the console screen and in the console log identifying the error condition.
You can view the console log at that point by selecting it from the console Main Menu.
If necessary to resolve the problem, contact your ProCurve authorized LAN dealer, or use
the electronic support services from ProCurve to get assistance. See the Customer
Support/Warranty booklet for more information.
➍
One or more of
the switch
cooling fans may
have failed.
Try disconnecting power from the switch and wait a few moments. Then reconnect the
power to the switch and check the LEDs again. If the error indication reoccurs, one or
more of the fans has failed. The switch may continue to operate under this condition if
the ambient temperature does not exceed normal room temperature, but for best
operation, the switch should be replaced. Contact your ProCurve authorized LAN dealer,
or use the electronic support services from ProCure to get assistance. See the Customer
Support/Warranty booklet for more information.
➎
The network port
for which the LED
is blinking has
experienced a
self test or
initialization
failure.
If the Mdl Status
LED is blinking,
the affected port
is on the cl
Module.
Try power cycling the switch. If the fault indication reoccurs, the switch port may have
failed. Call your ProCurve authorized LAN dealer, or use the electronic support services
from ProCurve to get assistance. See the Customer Support/Warranty booklet for more
information.
If the port is a transceiver, verify it is one of the transceivers supported by the switch.
Unsupported transceivers will be identified with this fault condition. The supported
transceivers are listed in the ProCurve Switch cl Modules Installation Guide.
To verify the port has failed, try removing and reinstalling the transceiver without having
to power off the switch. If the port fault indication reoccurs, you will have to replace the
transceiver.
Troubleshooting
Tip
continued on the next page
4-4
Troubleshooting
Diagnosing with the LEDs
Problem
Solution
➏
The network
connection is not
working
properly.
Try the following procedures:
• For the indicated port, verify both ends of the cabling, at the switch and the connected
device, are connected properly.
• Verify the connected device and switch are both powered on and operating correctly.
• Verify you have used the correct cable type for the connection:
– For fiber-optic connections, verify the transmit port on the switch is connected to
the receive port on the connected device, and the switch receive port is connected
to the transmit port on the connected device.
• Verify the port has not been disabled through a switch configuration change.
You can use the console interface, or, if you have configured an IP address on the
switch, use the web browser interface, or ProCurve Manager network management
software to determine the state of the port and re-enable the port if necessary.
• Verify the switch port configuration matches the configuration of the attached device.
For example, if the switch port is configured as “Auto”, the port on the attached device
also MUST be configured as “Auto”. Depending on the port type, twisted-pair or fiberoptic, if the configurations do not match, the results could be a very unreliable
connection, or no link at all.
• If the other procedures do not resolve the problem, try using a different port or a
different cable.
➐
The port may be
improperly
configured, or
the port may be in
a “blocking”
state by the
normal operation
of the Spanning
Tree, LACP, or
IGMP features.
Use the switch console to see if the port is part of a dynamic trunk (through the LACP
feature) or to see if Spanning Tree is enabled on the switch, and to see if the port may
have been put into a “blocking” state by those features. The show lacp command displays
the port status for the LACP feature; the show spanning-tree command displays the port
status for Spanning Tree.
Also check the Port Status screen using the show interfaces command to see if the port
has been configured as “disabled”.
Other switch features that may affect the port operation include VLANs and IGMP. Use
the switch console to see how the port is configured for these features.
For software troubleshooting tips, see the chapter “Troubleshooting” in the Management
and Configuration Guide, which is on the Documentation CD-ROM that came with your
switch.
Make sure also, the device at the other end of the connection is indicating a good link to
the switch. If it is not, the problem may be with the cabling between the devices or the
connectors on the cable.
➑
An RPS is
connected but
the switch has
experienced an
internal power
supply fault.
Refer to the ProCurve 600/610 External Power Supplies documentation. You may have to
replace the switch.
➒
Expansion cl
module is
plugged in but
has experienced
a fault.
Check the rear of the switch. Check the module LEDs for indications. This condition will
only occur during an initialization self test.
4-5
Troubleshooting
Tip
Troubleshooting
Proactive Networking
Proactive Networking
The ProCurve Series 6400cl Switch devices have built-in management capabilities that proactively help you manage your network including:
■
finding and helping you fix the most common network error conditions
(for example, faulty network cabling, and non-standard network
topologies)
■
informing you of the problem with clear, easy-to-understand messages
■
recommending network configuration changes to enhance the
performance of your network
The following interfaces provide tests, indicators, and an event log that can
be used to monitor the switch and its network connections and to help you
take advantage of these proactive networking features:
■
ProCurve Manager - an SNMP-based network management tool that is
included with your switch.
■
A graphical web browser interface that you can use to manage your switch
from a PC running a supported web browser, for example Microsoft
Internet Explorer.
■
A full-featured easy-to-use console interface that you can access by
connecting a standard terminal or PC running a terminal emulator to the
switch’s console port. The cable to make that connection is provided with
your switch. The console interface is also accessible through a Telnet
connection.
Troubleshooting
For more information on using these software tools to diagnose and manage
your switch, see the “Troubleshooting” chapter in the Management and
Configuration Guide, which is on the Documentation CD-ROM that came
with your switch.
4-6
Troubleshooting
Hardware Diagnostic Tests
Hardware Diagnostic Tests
Testing the Switch by Resetting It
If you believe the switch is not operating correctly, you can reset the switch
to test its circuitry and operating code. To reset a switch, either:
■
unplug and plug in the power cord (power cycling)
■
press the Reset button on the front of the switch
Power cycling the switch and pressing the Reset button both cause the switch
to perform its power-on self test, which almost always will resolve any
temporary operational problems. These reset processes also cause any
network traffic counters to be reset to zero, and cause the System Up Time
timer to reset to zero.
Checking the Switch LEDs
The self test passes if the Fault and Test LEDs on the front of the switch go
off after approximately 50 seconds. If these LEDs stay on longer than 60
seconds or begin blinking, there may be a problem with the switch.
See “Diagnosing With the LEDs” on page 4-3 for information on interpreting
the LED patterns and LED behaviors in chapter one.
Checking Console Messages
4-7
Troubleshooting
Useful diagnostic messages may be displayed on the console screen when the
switch is reset. As described in chapter 2 under step 7, “Connect a Console to
the Switch”, connect a PC running a VT-100 terminal emulator program or a
standard VT-100 terminal to the switch’s Console Port and configure it to run
at 9600 baud, and with the other terminal communication settings shown on
page 2-18. Then, when you reset the switch, note the messages that are
displayed. Additionally, you can check the switch event log, which can be
accessed from the console using the show log command, or from the console
Main Menu.
Troubleshooting
Hardware Diagnostic Tests
Testing Switch-to-Device Network Communications
You can perform the following communication tests to verify the network is
operating correctly between the switch and any connected device that can
respond correctly to the communication test.
■
Link Test -- a physical layer test that sends IEEE 802.2 test packets to any
device identified by its MAC address.
■
Ping Test -- a network layer test used on IP networks that sends test
packets to any device identified by its IP address.
These tests can be performed through the switch console interface from a
terminal connected to the switch or through a Telnet connection, or from the
switch’s web browser interface. For more information, see the Management
and Configuration Guide, which is on the Documentation CD-ROM that came
with your switch.
These tests can also be performed from an SNMP network management
station running a program that can manage the switch, for example, ProCurve
Manager.
Testing End-to-End Network Communications
Troubleshooting
Both the switch and the cabling can be tested by running an end-to-end
communications test -- a test that sends known data from one network device
to another through the switch. For example, if you have two PCs on the
network that have LAN adapters between which you can run a link-level test
or Ping test through the switch, you can use this test to verify that the entire
communication path between the two PCs is functioning correctly. See your
LAN adapter documentation for more information on running a link test or
Ping test.
4-8
Troubleshooting
Restoring the Factory Default Configuration
Restoring the Factory Default
Configuration
As part of your troubleshooting process on the switch, it may become necessary to return the switch to the factory default settings. This process momentarily interrupts the switch operation, clears any passwords, clears the console
event log, resets the network counters to zero, performs a complete self test,
and reboots the switch into its factory default configuration including deleting
the IP address, if one is configured.
Note
This process removes all switch configuration changes you have made from
the factory default settings. This includes, for example, configuration of
VLANs, Spanning Tree, trunks, and stacking. Returning the configuration of
these features to their factory default settings (usually disabling them) may
result in network connectivity issues.
If the switch has a valid configuration, and you are restoring the factory default
settings for a reason other than configuration problems, you should save the
switch configuration prior to performing the factory default reset. Then, after
the reset and resolution of the original problem, you can restore the saved
configuration to the switch. For both the save and restore processes, you can
use the console copy command. For more information on this command, see
the Management and Configuration Guide, which is on the Documentation
CD-ROM that came with your switch.
You can restore the factory default configuration either on the switch itself,
or through the switch console.
To execute the factory default reset on the switch, perform these steps:
Using pointed objects, simultaneously press both the Reset and Clear
buttons on the front of the switch.
2.
Continue to press the Clear button while releasing the Reset button.
3.
When the Test LED begins to blink, release the Clear button.
The switch will then complete its self test and begin operating with its
configuration restored to the factory default settings.
To restore the factory default configuration using the console, execute the
erase startup-config command from the console command prompt.
4-9
Troubleshooting
1.
Troubleshooting
Downloading New Switch Software
Downloading New Switch Software
When product enhancements occur for the switch, new software can be
downloaded to the switch through several methods, for product enhancements and new features. For more information, see the Management and
Configuration Guide, which is on the Documentation CD-ROM that came
with your switch.
Troubleshooting
The new switch software would be available on the ProCurve Networking Web
site, http://www.procurve.com.
4-10
Troubleshooting
ProCurve Customer Support Services
ProCurve Customer Support Services
If you are still having trouble with your switch, ProCurve offers support 24
hours a day, seven days a week through the use of a number of automated
electronic services. See the Customer Support/Warranty booklet that came
with your switch for information on how to use these services to get technical
support. The ProCurve Networking Web site, http://www.procurve.com also
provides up-to-date support information.
Additionally, your ProCurve authorized network reseller can provide you with
assistance, both with services that they offer and with services offered by
ProCurve.
Before Calling Support
Before calling your networking dealer or ProCurve Support, to make the
support process most efficient, you first should have retrieved the following
information:
Information Item
Information Location
• product identification
the front of the switch, Switch 6400cl
(J8433A or J8474A)
• details about the switch’s status including the software (OS) version, a copy of
the switch configuration, a copy of the
switch Event Log, and a copy of the
switch status and counters information
switch console: show tech command
• copy of your network topology map, including network addresses assigned to
the relevant devices
your network records
Troubleshooting
4-11
A
Specifications
Specifications
Physical
Width:
44.3 cm (17.4 in)
Depth:
43.0 cm (16.9 in)
Height:
4.4 cm (1.7 in)
Weight:
6400cl (J8433A)
6410cl (J8474A)
5.6 kg (12.35 lbs)
6.15 kg (13.56 lbs)
Electrical
The switch automatically adjusts to any voltage between 100-240 volts and
either 50 or 60 Hz.
AC voltage:
100-240 volts
Maximum current:
3.0A/1.5A
Frequency range:
50/60 Hz
Environmental
Operating
Non-Operating
1
-40°C to 70°C (-40°F to 158°F)
Temperature:
0°C to 55°C (32°F to 131°F)
Relative humidity:
(non-condensing)
15% to 95% at 40°C (104°F)
15% to 90% at 65°C (149°F)
Maximum altitude:
4.6 km (15,000 ft)
4.6 km (15,000 ft)
1 If you are installing either of the Series 6400cl Switch devices using one of the fiber
transceivers, the operating ambient temperature should not exceed 40°C (104°F). See
transceiver specifications in the ProCurve Switch cl Modules Installation Guide.
A-1
Specifications
Acoustic
Specifications
Geraeuschemission LwA=55 dB am fiktiven Arbeitsplatz nach DIN 45635 T.19
Noise Emission LwA=55 dB at virtual workspace according to DIN 45635 T.19
Connectors
■
The copper ports are compatible with the IEEE 802.1ak standards.
■
The fiber-optic ports are compatible with the IEEE 802.1ae standards.
■
The console port is a standard RS-232, (standard DB-9) connector.
Safety
Complies with:
■
EN60950 / IEC60950
■
CSA 22.2 No. 60950
■
UL 60950
Lasers
The following products are Class 1 Laser Products.
Laser Klasse 1:
■
The 10-GbE X2-SC LR transceiver
■
The 10-GbE X2-SC ER transceiver
The following products are Class 1 or Class 1m Laser Products.
Laser Klasse 1 or Klasse 1m:
■
The 10-GbE X2-SC SR transceiver
The transceivers comply with IEC 60825.
A-2
B
Safety and EMC Regulatory Statements
Safety Information
!
Documentation reference symbol. If the product is marked with this
symbol, refer to the product documentation to get more information
about the product.
WARNING
A WARNING in the manual denotes a hazard that can cause injury
or death.
Caution
A Caution in the manual denotes a hazard that can damage equipment.
Do not proceed beyond a WARNING or Caution notice until you
have understood the hazardous conditions and have taken appropriate steps.
For LAN cable grounding:
■
If your LAN covers an area served by more than one power distribution system, be sure their safety grounds are securely interconnected.
■
LAN cables may occasionally be subject to hazardous transient voltages (such as lightning or disturbances in the electrical utilities power
grid). Handle exposed metal components of the network with caution.
Servicing
There are no user-serviceable parts inside these products. Any servicing,
adjustment, maintenance, or repair must be performed only by service-trained
personnel.
These products do not have a power switch; they are powered on when the
power cord is plugged in.
B-1
Safety and EMC Regulatory
Statements
Grounding
These are safety class I products and have protective earthing terminals. There
must be an uninterruptible safety earth ground from the main power source
to the product's input wiring terminals, power cord, or supplied power cord
set. Whenever it is likely that the protection has been impaired, disconnect
the power cord until the ground has been restored.
Safety and EMC Regulatory Statements
Informations concernant la sécurité
Informations concernant la sécurité
!
Symbole de référence à la documentation. Si le produit est marqué de
ce symbole, reportez-vous à la documentation du produit afin d'obtenir
des informations plus détaillées.
WARNING
Dans la documentation, un WARNING indique un danger susceptible
d'entraîner des dommages corporels ou la mort.
Caution
Un texte de mise en garde intitulé Caution indique un danger susceptible de causer des dommages à l'équipement.
Ne continuez pas au-delà d'une rubrique WARNING ou Caution avant
d'avoir bien compris les conditions présentant un danger et pris les
mesures appropriées.
Cet appareil est un produit de classe I et possède une borne de mise à la terre. La source
d'alimentation principale doit être munie d'une prise de terre de sécurité installée aux
bornes du câblage d'entrée, sur le cordon d'alimentation ou le cordon de raccordement
fourni avec le produit. Lorsque cette protection semble avoir été endommagée,
débrancher le cordon d'alimentation jusqu'à ce que la mise à la terre ait été réparée.
Safety and EMC Regulatory
Statements
Mise à la terre du câble de réseau local:
■
si votre réseau local s'étend sur une zone desservie par plus d'un système de
distribution de puissance, assurez-vous que les prises de terre de sécurité
soient convenablement interconnectées.
■
Les câbles de réseaux locaux peuvent occasionnellement être soumis à des
surtensions transitoires dangereuses (telles que la foudre ou des perturbations dans le réseau d'alimentation public). Manipulez les composants
métalliques du réseau avec précautions.
Aucune pièce contenue à l'intérieur de ce produit ne peut être réparée par l'utilisateur.
Tout dépannage, réglage, entretien ou réparation devra être confié exclusivement à un
personnel qualifié.
Cet appareil ne comporte pas de commutateur principal ; la mise sous tension est
effectuée par branchement du cordon d'alimentation.
B-2
Safety and EMC Regulatory Statements
Hinweise zur Sicherheit
Hinweise zur Sicherheit
!
Symbol für Dokumentationsverweis. Wenn das Produkt mit diesem
Symbol markiert ist, schlagen Sie bitte in der Produktdokumentation
nach, um mehr Informationen über das Produkt zu erhalten.
WARNING
Eine WARNING in der Dokumentation symbolisiert eine Gefahr, die
Verletzungen oder sogar Todesfälle verursachen kann.
Caution
Caution in der Dokumentation symbolisiert eine Gefahr, die dis Gerät
beschädigen kann.
Fahren Sie nach dem Hinweis WARNING oder Caution erst fort,
nachdem Sie den Gefahrenzustand verstanden und die entsprechenden Maßnahmen ergriffen haben.
Dies ist ein Gerät der Sicherheitsklasse I und verfügt über einen schützenden Erdungsterminal. Der Betrieb des Geräts erfordert eine ununterbrochene Sicherheitserdung
von der Hauptstromquelle zu den Geräteingabeterminals, den Netzkabeln oder dem
mit Strom belieferten Netzkabelsatz voraus. Sobald Grund zur Annahme besteht, daß
der Schutz beeinträchtigt worden ist, das Netzkabel aus der Wandsteckdose herausziehen, bis die Erdung wiederhergestellt ist.
■
Wenn Ihr LAN ein Gebiet umfaßt, das von mehr als einem Stromverteilungssystem beliefert wird, müssen Sie sich vergewissern, daß die
Sicherheitserdungen fest untereinander verbunden sind.
■
LAN-Kabel können gelegentlich gefährlichen Übergangsspannungen ausgesetzt werden (beispielsweise durch Blitz oder Störungen in dem
Starkstromnetz des Elektrizitätswerks). Bei der Handhabung exponierter
Metallbestandteile des Netzwerkes Vorsicht walten lassen.
Dieses Gerät enthält innen keine durch den Benutzer zu wartenden Teile. Wartungs-,
Anpassungs-, Instandhaltungs- oder Reparaturarbeiten dürfen nur von geschultem
Bedienungspersonal durchgeführt werden.
Dieses Gerät hat keinen Netzschalter; es wird beim Anschließen des Netzkabels
eingeschaltet.
B-3
Safety and EMC Regulatory
Statements
Für LAN-Kabelerdung:
Safety and EMC Regulatory Statements
Considerazioni sulla sicurezza
Considerazioni sulla sicurezza
!
Simbolo di riferimento alla documentazione. Se il prodotto è contrassegnato da questo simbolo, fare riferimento alla documentazione sul
prodotto per ulteriori informazioni su di esso.
WARNING
La dicitura WARNINGdenota un pericolo che può causare lesioni o
morte.
Caution
La dicituraCaution denota un pericolo che può danneggiare le attrezzature.
Non procedere oltre un avviso di WARNING o di Cautionprima di
aver compreso le condizioni di rischio e aver provveduto alle misure
del caso.
Questo prodotto è omologato nella classe di sicurezza I ed ha un terminale protettivo
di collegamento a terra. Dev'essere installato un collegamento a terra di sicurezza, non
interrompibile che vada dalla fonte d'alimentazione principale ai terminali d'entrata,
al cavo d'alimentazione oppure al set cavo d'alimentazione fornito con il prodotto.
Ogniqualvolta vi sia probabilità di danneggiamento della protezione, disinserite il cavo
d'alimentazione fino a quando il collegaento a terra non sia stato ripristinato.
Safety and EMC Regulatory
Statements
Per la messa a terra dei cavi LAN:
■
se la vostra LAN copre un'area servita da più di un sistema di distribuzione
elettrica, accertatevi che i collegamenti a terra di sicurezza siano ben collegati
fra loro;
■
i cavi LAN possono occasionalmente andare soggetti a pericolose tensioni
transitorie (ad esempio, provocate da lampi o disturbi nella griglia d'alimentazione della società elettrica); siate cauti nel toccare parti esposte in metallo
della rete.
Nessun componente di questo prodotto può essere riparato dall'utente. Qualsiasi
lavoro di riparazione, messa a punto, manutenzione o assistenza va effettuato esclusivamente da personale specializzato.
Questo apparato non possiede un commutatore principale; si mette scotto tensione
all'inserirsi il cavo d'alimentazione.
B-4
Safety and EMC Regulatory Statements
Consideraciones sobre seguridad
Consideraciones sobre seguridad
!
Símbolo de referencia a la documentación. Si el producto va
marcado con este símbolo, consultar la documentación del
producto a fin de obtener mayor información sobre el producto.
WARNING
Una WARNING en la documentación señala un riesgo que podría
resultar en lesiones o la muerte.
Caution
Una Caution en la documentación señala un riesgo que podría
resultar en averías al equipo.
No proseguir después de un símbolo de WARNING o Caution hasta
no haber entendido las condiciones peligrosas y haber tomado las
medidas apropiadas.
Este aparato se enmarca dentro de la clase I de seguridad y se encuentra protegido por
una borna de puesta a tierra. Es preciso que exista una puesta a tierra continua desde
la toma de alimentación eléctrica hasta las bornas de los cables de entrada del aparato,
el cable de alimentación o el juego de cable de alimentación suministrado. Si existe la
probabilidad de que la protección a tierra haya sufrido desperfectos, desenchufar el
cable de alimentación hasta haberse subsanado el problema.
■
Si la LAN abarca un área cuyo suministro eléctrico proviene de más de una
red de distribución de electricidad, cerciorarse de que las puestas a tierra
estén conectadas entre sí de modo seguro.
■
Es posible que los cables de la LAN se vean sometidos de vez en cuando a
voltajes momentáneos que entrañen peligro (rayos o alteraciones en la red
de energía eléctrica). Manejar con precaución los componentes de metal de
la LAN que estén al descubierto.
Este aparato no contiene pieza alguna susceptible de reparación por parte del usuario.
Todas las reparaciones, ajustes o servicio de mantenimiento debe realizarlos solamente el técnico.
Este producto no tiene interruptor de potencia; se activa cuando se enchufa el cable
de alimentación.
B-5
Safety and EMC Regulatory
Statements
Puesta a tierra del cable de la red local (LAN):
Safety and EMC Regulatory Statements
Safety Information (Japan)
Safety and EMC Regulatory
Statements
Safety Information (Japan)
Japan Power
Cord Warning
B-6
Safety and EMC Regulatory Statements
Safety Information (China)
Safety Information (China)
Safety and EMC Regulatory
Statements
B-7
Safety and EMC Regulatory Statements
EMC Regulatory Statements
EMC Regulatory Statements
U.S.A.
FCC Class A
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause interference to
radio communications. Operation of this equipment in a residential area may
cause interference in which case the user will be required to correct the
interference at his own expense.
Canada
This product complies with Class A Canadian EMC requirements.
Safety and EMC Regulatory
Statements
Australia/New Zealand
This product complies with Australia/New Zealand EMC Class A
requirements.
Japan
VCCI Class A
B-8
Safety and EMC Regulatory Statements
EMC Regulatory Statements
Korea
Taiwan
Safety and EMC Regulatory
Statements
B-9
Safety and EMC Regulatory Statements
EMC Regulatory Statements
European Community
DECLARATION OF CONFORMITY
according to ISO/IEC Guide 22 and EN 45014
______________________________________________________________________
Manufacturer's Name:
Hewlett-Packard Company
Manufacturer's Address: 8000 Foothills Blvd.
Roseville, CA 95747-5502
U.S.A.
declares, that the product
Product Name:
HP ProCurve Switch 10-GbE CX4 6400cl-6XG
HP ProCurve Switch 10-GbE X2 6410cl-6XG
Product Number(s):
J8433A, J8474A
Regulatory Model:
RSVLC-0409
Product Options:
All
Safety and EMC Regulatory
Statements
conforms to the following Product Specifications:
Safety:
EN 60950:2000 / IEC 60950:1999
EMC:
EN 55022:1998 / CISPR 22:1997 Class A
EN 55024:1998 +A1 / CISPR 24:1997 +A1
EN 61000-3-2:2000 / IEC 61000-3-2:2001
EN 61000-3-3:1995 +A1 / IEC 61000-3-3:1994 +A1
Supplementary Information:
The product herewith complies with the requirements of the Low Voltage Directive
73/23/EEC and the EMC Directive 89/336/EEC and carries the CE marking accordingly.
This product is assigned a Regulatory Model Number which stays with the regulatory
aspects of the design. The Regulatory Model Number is the main product identifier in the
regulatory documentation and test reports. This number should not be confused with the
product marketing name or product numbers.
Roseville, 5 January 2005
European Contact: Your local Hewlett-Packard Sales and Service Office or Hewlett-Packard GmbH, Department
HQ-TRE, Herrenberger Straße 140, D-71034 Böblingen (FAX: + 49-7031-14-3143)
B-10
C
Recycle Statements
Waste Electrical and Electronic
Equipment (WEEE) Statements
Disposal of Waste Equipment by Users in Private Household in the European Union
This symbol on the product or on its packaging indicates that this product must not be disposed of with
your other household waste. Instead, it is your responsibility to dispose of your waste equipment by
handing it over to a designated collection point for the recycling of waste electrical and electronic
equipment. The separate collection and recycling of your waste equipment at the time of disposal will
help to conserve natural resources and ensure that it is recycled in a manner that protects human health
and the environment. For more information about where you can drop off your waste equipment for
recycling, please contact your local city office, your household waste disposal service or the shop where
you purchased the product.
Bortskaffelse af affald fra husstande i den Europæiske Union
Hvis produktet eller dets emballage er forsynet med dette symbol, angiver det, at produktet ikke må
bortskaffes med andet almindeligt husholdningsaffald. I stedet er det dit ansvar at bortskaffe kasseret
udstyr ved at aflevere det på den kommunale genbrugsstation, der forestår genvinding af kasseret
elektrisk og elektronisk udstyr. Den centrale modtagelse og genvinding af kasseret udstyr i forbindelse
med bortskaffelsen bidrager til bevarelse af naturlige ressourcer og sikrer, at udstyret genvindes på en
måde, der beskytter både mennesker og miljø. Yderligere oplysninger om, hvor du kan aflevere kasseret
udstyr til genvinding, kan du få hos kommunen, den lokale genbrugsstation eller i den butik, hvor du købte
produktet.
Seadmete jäätmete kõrvaldamine eramajapidamistes Euroopa Liidus
See tootel või selle pakendil olev sümbol näitab, et kõnealust toodet ei tohi koos teiste majapidamisjäätmetega kõrvaldada. Teie kohus on oma seadmete jäätmed kõrvaldada, viies need elektri- ja elektroonikaseadmete jäätmete ringlussevõtmiseks selleks ettenähtud kogumispunkti. Seadmete jäätmete eraldi
kogumine ja ringlussevõtmine kõrvaldamise ajal aitab kaitsta loodusvarasid ning tagada, et ringlussevõtmine toimub viisil, mis kaitseb inimeste tervist ning keskkonda. Lisateabe saamiseks selle kohta, kuhu
oma seadmete jäätmed ringlussevõtmiseks viia, võtke palun ühendust oma kohaliku linnakantselei,
majapidamisjäätmete kõrvaldamise teenistuse või kauplusega, kust Te toote ostsite.
C-1
Recycle Statements
Likvidace zařízení soukromými domácími uživateli v Evropské unii
Tento symbol na produktu nebo balení označuje výrobek, který nesmí být vyhozen spolu s ostatním
domácím odpadem. Povinností uživatele je předat takto označený odpad na předem určené sběrné
místo pro recyklaci elektrických a elektronických zařízení. Okamžité třídění a recyklace odpadu
pomůže uchovat přírodní prostředí a zajistí takový způsob recyklace, který ochrání zdraví a životní
prostředí člověka. Další informace o možnostech odevzdání odpadu k recyklaci získáte na
příslušném obecním nebo městském úřadě, od firmy zabývající se sběrem a svozem odpadu nebo v
obchodě, kde jste produkt zakoupili.
Recycle Statements
Waste Electrical and Electronic Equipment (WEEE) Statements
Laitteiden hävittäminen kotitalouksissa Euroopan unionin alueella
Jos tuotteessa tai sen pakkauksessa on tämä merkki, tuotetta ei saa hävittää kotitalousjätteiden mukana.
Tällöin hävitettävä laite on toimitettava sähkölaitteiden ja elektronisten laitteiden kierrätyspisteeseen.
Hävitettävien laitteiden erillinen käsittely ja kierrätys auttavat säästämään luonnonvaroja ja
varmistamaan, että laite kierrätetään tavalla, joka estää terveyshaitat ja suojelee luontoa. Lisätietoja
paikoista, joihin hävitettävät laitteet voi toimittaa kierrätettäväksi, saa ottamalla yhteyttä jätehuoltoon tai
liikkeeseen, josta tuote on ostettu.
Élimination des appareils mis au rebut par les ménages dans l'Union européenne
Le symbole apposé sur ce produit ou sur son emballage indique que ce produit ne doit pas être jeté avec
les déchets ménagers ordinaires. Il est de votre responsabilité de mettre au rebut vos appareils en les
déposant dans les centres de collecte publique désignés pour le recyclage des équipements électriques
et électroniques. La collecte et le recyclage de vos appareils mis au rebut indépendamment du reste
des déchets contribue à la préservation des ressources naturelles et garantit que ces appareils seront
recyclés dans le respect de la santé humaine et de l'environnement. Pour obtenir plus d'informations
sur les centres de collecte et de recyclage des appareils mis au rebut, veuillez contacter les autorités
locales de votre région, les services de collecte des ordures ménagères ou le magasin dans lequel vous
avez acheté ce produit.
Entsorgung von Altgeräten aus privaten Haushalten in der EU
Das Symbol auf dem Produkt oder seiner Verpackung weist darauf hin, dass das Produkt nicht über den
normalen Hausmüll entsorgt werden darf. Benutzer sind verpflichtet, die Altgeräte an einer Rücknahmestelle für Elektro- und Elektronik-Altgeräte abzugeben. Die getrennte Sammlung und ordnungsgemäße Entsorgung Ihrer Altgeräte trägt zur Erhaltung der natürlichen Ressourcen bei und garantiert
eine Wiederverwertung, die die Gesundheit des Menschen und die Umwelt schützt. Informationen dazu,
wo Sie Rücknahmestellen für Ihre Altgeräte finden, erhalten Sie bei Ihrer Stadtverwaltung, den örtlichen
Müllentsorgungsbetrieben oder im Geschäft, in dem Sie das Gerät erworben haben
Recycle Statements
Απόρριψη άχρηστου εξοπλισµού από χρήστες σε ιδιωτικά νοικοκυριά στην Ευρωπαϊκή
Ένωση
Το σύµβολο αυτό στο προϊόν ή τη συσκευασία του υποδεικνύει ότι το συγκεκριµένο προϊόν δεν
πρέπει να διατίθεται µαζί µε τα άλλα οικιακά σας απορρίµµατα. Αντίθετα, είναι δική σας ευθύνη να
απορρίψετε τον άχρηστο εξοπλισµό σας παραδίδοντάς τον σε καθορισµένο σηµείο συλλογής για την
ανακύκλωση άχρηστου ηλεκτρικού και ηλεκτρονικού εξοπλισµού. Η ξεχωριστή συλλογή και
ανακύκλωση του άχρηστου εξοπλισµού σας κατά την απόρριψη θα συµβάλει στη διατήρηση των
φυσικών πόρων και θα διασφαλίσει ότι η ανακύκλωση γίνεται µε τρόπο που προστατεύει την
ανθρώπινη υγεία και το περιβάλλον. Για περισσότερες πληροφορίες σχετικά µε το πού µπορείτε να
παραδώσετε τον άχρηστο εξοπλισµό σας για ανακύκλωση, επικοινωνήστε µε το αρµόδιο τοπικό
γραφείο, την τοπική υπηρεσία διάθεσης οικιακών απορριµµάτων ή το κατάστηµα όπου αγοράσατε το
προϊόν.
Készülékek magánháztartásban történő selejtezése az Európai Unió területén
A készüléken, illetve a készülék csomagolásán látható azonos szimbólum annak jelzésére szolgál,
hogy a készülék a selejtezés során az egyéb háztartási hulladéktól eltérő módon kezelendő. A
vásárló a hulladékká vált készüléket köteles a kijelölt gyűjtőhelyre szállítani az elektromos és
elektronikai készülékek újrahasznosítása céljából. A hulladékká vált készülékek selejtezéskori
begyűjtése és újrahasznosítása hozzájárul a természeti erőforrások megőrzéséhez, valamint
biztosítja a selejtezett termékek környezetre és emberi egészségre nézve biztonságos feldolgozását.
A begyűjtés pontos helyéről bővebb tájékoztatást a lakhelye szerint illetékes önkormányzattól, az
illetékes szemételtakarító vállalattól, illetve a terméket elárusító helyen kaphat.
C-2
Recycle Statements
Waste Electrical and Electronic Equipment (WEEE) Statements
Smaltimento delle apparecchiature da parte di privati nel territorio dell'Unione Europea
Questo simbolo presente sul prodotto o sulla sua confezione indica che il prodotto non può essere
smaltito insieme ai rifiuti domestici. È responsabilità dell'utente smaltire le apparecchiature consegnandole presso un punto di raccolta designato al riciclo e allo smaltimento di apparecchiature elettriche ed
elettroniche. La raccolta differenziata e il corretto riciclo delle apparecchiature da smaltire permette di
proteggere la salute degli individui e l'ecosistema. Per ulteriori informazioni relative ai punti di raccolta
delle apparecchiature, contattare l'ente locale per lo smaltimento dei rifiuti, oppure il negozio presso il
quale è stato acquistato il prodotto.
Nolietotu iekārtu iznīcināšanas noteikumi lietotājiem Eiropas Savienības privātajās
mājsaimniecībās
Šāds simbols uz izstrādājuma vai uz tā iesaiņojuma norāda, ka šo izstrādājumu nedrīkst izmest kopā ar
citiem sadzīves atkritumiem. Jūs atbildat par to, lai nolietotās iekārtas tiktu nodotas speciāli iekārtotos
punktos, kas paredzēti izmantoto elektrisko un elektronisko iekārtu savākšanai otrreizējai pārstrādei.
Atsevišķa nolietoto iekārtu savākšana un otrreizējā pārstrāde palīdzēs saglabāt dabas resursus un
garantēs, ka šīs iekārtas tiks otrreizēji pārstrādātas tādā veidā, lai pasargātu vidi un cilvēku veselību.
Lai uzzinātu, kur nolietotās iekārtas var izmest otrreizējai pārstrādei, jāvēršas savas dzīves vietas
pašvaldībā, sadzīves atkritumu savākšanas dienestā vai veikalā, kurā izstrādājums tika nopirkts.
Vartotojų iš privačių namų ūkių įrangos atliekų šalinimas Europos Sąjungoje
Šis simbolis ant gaminio arba jo pakuotės rodo, kad šio gaminio šalinti kartu su kitomis namų ūkio
atliekomis negalima. Šalintinas įrangos atliekas privalote pristatyti į specialią surinkimo vietą elektros ir
elektroninės įrangos atliekoms perdirbti. Atskirai surenkamos ir perdirbamos šalintinos įrangos atliekos
padės saugoti gamtinius išteklius ir užtikrinti, kad jos bus perdirbtos tokiu būdu, kuris nekenkia žmonių
sveikatai ir aplinkai. Jeigu norite sužinoti daugiau apie tai, kur galima pristatyti perdirbtinas įrangos
atliekas, kreipkitės į savo seniūniją, namų ūkio atliekų šalinimo tarnybą arba parduotuvę, kurioje
įsigijote gaminį.
Pozbywanie się zużytego sprzętu przez użytkowników w prywatnych gospodarstwach
domowych w Unii Europejskiej
Ten symbol na produkcie lub jego opakowaniu oznacza, że produktu nie wolno wyrzucać do zwykłych
pojemników na śmieci. Obowiązkiem użytkownika jest przekazanie zużytego sprzętu do
wyznaczonego punktu zbiórki w celu recyklingu odpadów powstałych ze sprzętu elektrycznego i
elektronicznego. Osobna zbiórka oraz recykling zużytego sprzętu pomogą w ochronie zasobów
naturalnych i zapewnią ponowne wprowadzenie go do obiegu w sposób chroniący zdrowie człowieka
i środowisko. Aby uzyskać więcej informacji o tym, gdzie można przekazać zużyty sprzęt do
recyklingu, należy się skontaktować z urzędem miasta, zakładem gospodarki odpadami lub sklepem,
w którym zakupiono produkt.
C-3
Recycle Statements
Verwijdering van afgedankte apparatuur door privé-gebruikers in de Europese Unie
Dit symbool op het product of de verpakking geeft aan dat dit product niet mag worden gedeponeerd bij
het normale huishoudelijke afval. U bent zelf verantwoordelijk voor het inleveren van uw afgedankte
apparatuur bij een inzamelingspunt voor het recyclen van oude elektrische en elektronische apparatuur.
Door uw oude apparatuur apart aan te bieden en te recyclen, kunnen natuurlijke bronnen worden
behouden en kan het materiaal worden hergebruikt op een manier waarmee de volksgezondheid en het
milieu worden beschermd. Neem contact op met uw gemeente, het afvalinzamelingsbedrijf of de winkel
waar u het product hebt gekocht voor meer informatie over inzamelingspunten waar u oude apparatuur
kunt aanbieden voor recycling.
Recycle Statements
Waste Electrical and Electronic Equipment (WEEE) Statements
Descarte de Lixo Elétrico na Comunidade Européia
Este símbolo encontrado no produto ou na embalagem indica que o produto não deve ser descartado
no lixo doméstico comum. É responsabilidade do cliente descartar o material usado (lixo elétrico),
encaminhando-o para um ponto de coleta para reciclagem. A coleta e a reciclagem seletivas desse
tipo de lixo ajudarão a conservar as reservas naturais; sendo assim, a reciclagem será feita de uma
forma segura, protegendo o ambiente e a saúde das pessoas. Para obter mais informações sobre locais
que reciclam esse tipo de material, entre em contato com o escritório da HP em sua cidade, com o serviço
de coleta de lixo ou com a loja em que o produto foi adquirido.
Likvidácia vyradených zariadení v domácnostiach v Európskej únii
Symbol na výrobku alebo jeho balení označuje, že daný výrobok sa nesmie likvidovať s domovým
odpadom. Povinnosťou spotrebiteľa je odovzdať vyradené zariadenie v zbernom mieste, ktoré je
určené na recykláciu vyradených elektrických a elektronických zariadení. Separovaný zber a
recyklácia vyradených zariadení prispieva k ochrane prírodných zdrojov a zabezpečuje, že recyklácia
sa vykonáva spôsobom chrániacim ľudské zdravie a životné prostredie. Informácie o zberných
miestach na recykláciu vyradených zariadení vám poskytne miestne zastupiteľstvo, spoločnosť
zabezpečujúca odvoz domového odpadu alebo obchod, v ktorom ste si výrobok zakúpili.
Odstranjevanje odslužene opreme uporabnikov v zasebnih gospodinjstvih v Evropski uniji
Ta znak na izdelku ali njegovi embalaži pomeni, da izdelka ne smete odvreči med gospodinjske
odpadke. Nasprotno, odsluženo opremo morate predati na zbirališče, pooblaščeno za recikliranje
odslužene električne in elektronske opreme. Ločeno zbiranje in recikliranje odslužene opreme
prispeva k ohranjanju naravnih virov in zagotavlja recikliranje te opreme na zdravju in okolju neškodljiv
način. Za podrobnejše informacije o tem, kam lahko odpeljete odsluženo opremo na recikliranje, se
obrnite na pristojni organ, komunalno službo ali trgovino, kjer ste izdelek kupili.
Recycle Statements
Eliminación de residuos de equipos eléctricos y electrónicos por parte de usuarios particulares en la
Unión Europea
Este símbolo en el producto o en su envase indica que no debe eliminarse junto con los desperdicios
generales de la casa. Es responsabilidad del usuario eliminar los residuos de este tipo depositándolos
en un "punto limpio" para el reciclado de residuos eléctricos y electrónicos. La recogida y el reciclado
selectivos de los residuos de aparatos eléctricos en el momento de su eliminación contribuirá a
conservar los recursos naturales y a garantizar el reciclado de estos residuos de forma que se proteja
el medio ambiente y la salud. Para obtener más información sobre los puntos de recogida de residuos
eléctricos y electrónicos para reciclado, póngase en contacto con su ayuntamiento, con el servicio de
eliminación de residuos domésticos o con el establecimiento en el que adquirió el producto.
Bortskaffande av avfallsprodukter från användare i privathushåll inom Europeiska Unionen
Om den här symbolen visas på produkten eller förpackningen betyder det att produkten inte får
slängas på samma ställe som hushållssopor. I stället är det ditt ansvar att bortskaffa avfallet genom att
överlämna det till ett uppsamlingsställe avsett för återvinning av avfall från elektriska och elektroniska
produkter. Separat insamling och återvinning av avfallet hjälper till att spara på våra naturresurser och
gör att avfallet återvinns på ett sätt som skyddar människors hälsa och miljön. Kontakta ditt lokala
kommunkontor, din närmsta återvinningsstation för hushållsavfall eller affären där du köpte produkten
för att få mer information om var du kan lämna ditt avfall för återvinning.
C-4
Index
Numerics
10 Gigabit
10-GbE … 1-1, 1-4, 1-10
A
AC power connector
location on back of switch … 1-9
Act LED … 1-5, 1-7–1-8
B
back of switch
cl module slot … 1-9
description … 1-9
power connector … 1-9
RPS input port … 1-9
basic switch configuration
IP address … 3-3
manager password … 3-2
subnet mask … 3-3
Switch Setup screen … 3-2
basic troubleshooting tips … 4-1
blinking LEDs
error indications … 4-3
Bootp
automatic switch configuration … 3-2
for in-band access … 2-18
buttons
Clear button … 1-4
Reset button … 1-4
C
D
deleting passwords … 1-4
Index – 1
Index
cabinet
mounting the switch in … 2-11
cables
connecting cables to switch ports … 2-14
effects of non-standard cables … 4-1
infrastructure requirements … 2-5
serial, for direct console connection … 2-19
cabling infrastructure … 2-5
cl module
install or remove … 2-7
cl module slot … 1-9
Clear button
deleting passwords … 1-4
description … 1-4
location on switch … 1-3–1-4
restoring factory default configuration … 1-5,
4-9
to delete password protection … 3-4
CLI prompt, console
displaying … 2-19
configuration
checking when troubleshooting … 4-2
DHCP/Bootp … 3-2
IP address … 3-3
IP address, manually … 3-2
manager password … 3-2
restoring factory defaults … 1-5, 4-9
subnet mask … 3-3
Switch Setup screen … 3-2
connecting the switch to a power source … 2-13
connecting the switch to an RPS/EPS … 2-17
connector specifications … A-2
console
checking messages during
troubleshooting … 4-7
displaying the CLI prompt … 2-19
features … 2-18
how to connect in-band … 2-18
how to connect out-of-band … 2-18
serial cable connection … 2-19
Switch Setup screen … 3-2
Telnet access … 3-5
terminal configuration … 2-18
console port … 1-4
location on switch … 1-3
description
back of switch … 1-9
front of switch … 1-3
LEDs … 1-5
switch … 1-1
DHCP
automatic switch configuration … 3-2
for in-band access … 2-18
diagnostic tests … 4-7
checking the console messages … 4-7
checking the LEDs … 4-7
end-to-end connectivity … 4-8
testing the switch only … 4-7
downloading new switch software … 4-10
E
electrical specifications, switch … A-1
EMC regulatory statements … B-8
environmental specifications, switch … A-1
expansion modules LEDs … 1-8
F
Index
factory default configuration, restoring … 1-5, 4-9
Fan Status LED … 1-6
Fault LED … 1-5
behavior during self test … 2-11
behaviors … 1-5
blinking definition … 1-6
showing error conditions … 4-3
features
console … 2-18
switch … 1-10
front of switch … 1-3
Clear button … 1-4
LEDs … 1-5
network ports … 1-4
Reset button … 1-4
2 – Index
H
horizontal surface
mounting switch on … 2-13
I
in-band … 3-1
in-band console access
types of … 2-18
included parts … 2-1
installation
cl module … 2-7
connecting the switch to a power source … 2-13
horizontal surface mounting … 2-13
location considerations … 2-6
network cable requirements … 2-5
precautions … 2-4
rack or cabinet mounting … 2-11
site preparation … 2-5
summary of steps … 2-3
transceiver … 2-8
IP address
configuring … 3-3
L
LEDs
Act … 1-5, 1-7–1-8
behavior during self test … 2-10
blinking definition … 1-6
checking during troubleshooting … 4-7
descriptions of … 1-5
EPS/RPS … 2-16
error indications … 4-3
expansion module … 1-8
Fan Status … 1-6
Fault … 1-5
behavior during self test … 2-11
showing error conditions … 4-3
Link … 1-5, 1-7–1-8
location on switch … 1-3
on switch … 1-5
port
description … 1-5
Port LED View select indicators … 1-5
Port View
selecting the display … 1-7
Power … 1-5
behavior during self test … 2-11
Self Test … 1-6
behavior during self test … 2-10
Link LED … 1-7
Link LEDs … 1-5, 1-8
link test … 4-8
location for the switch, considerations … 2-6
P
network cables
required types … 2-5
network devices
connecting to the switch … 2-14
network ports
connecting to … 2-14
location on switch … 1-4
standards compliance … A-2
types of … 1-4
non-standard network cables, effects … 4-1
parts, included with the switch … 2-1
password
configuring … 3-2
passwords
deleting with the Clear button … 3-4
if you lose the password … 3-4
passwords, deleting … 1-4
physical specifications, switch … A-1
Ping test … 4-8
port configuration
checking when troubleshooting … 4-2
Port LED View
indicator LEDs … 1-7
select button … 1-7
selecting the display … 1-7
port LEDs
description … 1-5
Link … 1-5, 1-8
normal operation … 2-11
ports
connecting to … 2-14
console … 2-18
network connections … 2-14
power connector … 1-9
Power LED … 1-5
behavior during self test … 2-11
behaviors … 1-5
power source
connecting the switch to … 2-13
precautions
mounting the switch … 2-4
power requirements … 2-4
preparing the installation site … 2-5
Proactive Network tools
diagnostics with … 4-6
O
R
out-of-band console access … 3-5
rack
M
mounting the switch
in a rack or cabinet … 2-11
precautions … 2-4
on a horizontal surface … 2-13
N
Index
mounting precautions … 2-4
mounting the switch in … 2-11
recycle statements … C-1
Index – 3
Redundant Power Supply … 2-15
redundant power supply
RPS/EPS … 1-1
regulatory statements … B-8
remote campus
topology with … 2-21
Reset button
description … 1-4
location on switch … 1-3–1-4
restoring factory default configuration … 4-9
resetting the switch
factory default reset … 4-9
location of Reset button … 1-4
troubleshooting procedure … 4-7
RPS input port … 1-9
RPS LED behavior … 1-6
RPS/EPS … 2-15
cables … 2-15
connecting to a switch … 2-17
operation … 2-17
switch
connecting to a power source … 2-13
description … 1-1
downloading new software … 4-10
electrical specifications … A-1
environmental specifications … A-1
features … 1-10
front panel description … 1-3
included parts … 2-1
LED descriptions … 1-5
mounting in a rack or cabinet … 2-11
mounting on horizontal surface … 2-13
physical specifications … A-1
switch operation
verifying after installation … 2-9
Switch Setup screen … 3-2
configuring a subnet mask … 3-3
configuring an IP address … 3-3
field descriptions … 3-3
T
Index
S
safety and regulatory statements … B-1
safety specifications … A-2
selecting the Port LED View display … 1-7
self test
Fault LED behavior … 2-11
LED behavior during … 2-10
Power LED behavior … 2-11
Self Test LED … 1-6
behavior during factory default reset … 4-9
serial cable
for direct console connection … 2-19
specifications
connectors … A-2
electrical … A-1
environmental … A-1
physical … A-1
safety … A-2
subnet mask
configuring … 3-3
summary
of switch installation … 2-3
4 – Index
Telnet access to the console … 3-5
terminal configuration … 2-18
Test LED
behavior during self test … 2-10
testing
checking the console messages … 4-7
checking the LEDs … 4-7
diagnostic tests … 4-7
end-to-end communications … 4-8
link test … 4-8
Ping test … 4-8
switch operation … 4-7
switch-to-device communications … 4-8
three tier model
sample topology … 2-20
tips for troubleshooting … 4-1
topologies
effects of improper topology … 4-2
samples of … 2-20
transceiver
install or remove … 2-8
troubleshooting … 4-1
basic tips … 4-1
checking port configuration … 4-2
checking the console messages … 4-7
checking the LEDs … 4-7
common network problems … 4-1
diagnostic tests … 4-7
effects of improper topology … 4-2
effects of non-standard cables … 4-1
link test … 4-8
Ping test … 4-8
Proactive Network tools … 4-6
restoring factory default configuration … 4-9
testing connections to other devices … 4-8
testing end-to-end communications … 4-8
testing the switch … 4-7
V
VT-100 terminal
serial cable connection for … 2-19
Index
Index – 5
Technical information in this document
is subject to change without notice.
©Copyright 2004, 2006
Hewlett-Packard Development Company, L.P.
Reproduction, adaptation, or translation
without prior written permission is prohibited
except as allowed under the copyright laws.
Printed in Singapore
March 2006
Manual Part Number
5991-4701
*5991-4701*