HP Compaq W185q User's Manual

v185e/v185es/v185w/v185ws/w185/W185q LCD
Monitor User’s Guide
The only warranties for HP products and services are set forth in the express warranty statements accompanying such products
and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or
editorial errors or omissions contained herein.
HP assumes no responsibility for the use or reliability of its software on equipment that is not furnished by HP.
This document contains proprietary information that is protected by copyright. No part of this document may be photocopied,
reproduced, or translated to another language without the prior written consent of HP.
Hewlett-Packard Company
10955 Tantau Avenue
Cupertino, CA 95014-0770
USA
Copyright © 2009 Hewlett-Packard Development Company, L.P.
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights.
Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited payper-view viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.
Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation.
Adobe and Acrobat are trademarks of Adobe Systems Incorporated.
Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license.
HP supports lawful use of technology and does not endorse or encourage the use of its products for purposes other than those
permitted by copyright law.
The information in this document is subject to change without notice.
Preface
About This Guide
This guide is intended for anyone who uses the v185e / v185es / v185w / v185ws / w185 / W185q LCD Monitor. It
describes the monitor’s features, setup, and operation.
The sections are as follows:
y Safety and Maintenance Guidelines
y Setup
y Using the Monitor
y Installing Drivers and Using the Auto-Adjustment Feature
y Technical Support FAQs
y Specifications
y LCD Monitor Quality and Pixel Policy
y Agency Regulatory Notices
Notational Conventions
The following subsections describe notational conventions used in this document.
Notes, Cautions, and Warnings
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These
blocks are notes, cautions, and warnings, and they are used as follows:
NOTE: A NOTE indicates important information that helps you make better use of your monitor.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data, and tells you how to
avoid the problem.
WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the problem.
Some warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specific
presentation of the warning is mandated by regulatory authority.
3
Safety and Maintenance Guidelines
Important Safety Information
The power cord is designed for use with your monitor. To use a different cord, use only a power source and
connection compatible with this monitor. For information on the correct power cord set to use with your monitor, see
Power Cord Set Requirements.
WARNING: To reduce the risk of electric shock or damage to your equipment, do not disable the power cord
grounding feature. The grounding plug is an important safety feature. Connect the equipment to a grounded
(earthed) power outlet.
For your safety, be sure that the grounded power outlet you plug the power cord into is easily accessible to
the operator and located as close to the equipment as possible. To disconnect power from the equipment,
unplug the power cord from the power outlet by grasping the plug firmly. Never pull on the cord.
Before connecting cables, disconnect power from the monitor by unplugging the power cord from the
electrical outlet.
Do not place anything on power cords or cables. Arrange them so that no one can accidentally step on or trip
over them. Do not pull on a cord or cable. When unplugging from the electrical outlet, grasp the cord by its
plug.
CAUTION: To protect your monitor, as well as your computer, connect all power cords for your computer and
its peripheral devices (such as a monitor, printer, or scanner) to a surge protection device such as a power
strip with surge protection or uninterruptible power supply (UPS).
Not all power strips provide surge protection; the power strips must be specifically labeled as having this
ability. Use a power strip whose manufacturer offers a damage replacement policy so you can replace your
equipment if surge protection fails.
Safety Precautions
CAUTION: Avoid applying pressure to the LCD screen; doing so can cause damage.
y Use only a power source and connection compatible with this monitor, as indicated on the label/back plate
of the monitor.
y Be sure the total ampere rating of the products connected to the outlet does not exceed the current rating
of the electrical outlet, and the total ampere rating of the products connected to the cord does not exceed
the rating of the cord. Look on the power label to determine the ampere rating (Amps or A) for each device.
4
y Install your monitor near an outlet that you can easily reach. Disconnect the monitor by grasping the plug
firmly and pulling it from the outlet. Never disconnect the monitor by pulling the cord.
y Do not allow anything to rest on the power cord. Do not walk on the cord.
Maintenance Guidelines
To enhance the performance and extend the life of your monitor:
y Do not open your monitor cabinet or attempt to service this product yourself. If your monitor is not operating
properly or has been dropped or damaged, contact your HP authorized dealer, reseller, or service provider.
y Adjust only those controls that are described in the operating instructions.
y Turn your monitor off when not in use. You can substantially increase the life expectancy of your monitor by using a
screen saver and turning off the monitor when not in use.
y Keep your monitor in a well-ventilated area, away from excessive light, heat, or moisture.
y Slots and openings in the cabinet are provided for ventilation. These openings must not be blocked or
covered. Never push objects of any kind into cabinet slots or other openings.
y Unplug your monitor from the wall outlet before cleaning.
y Do not drop your monitor or place it on an unstable surface.
y When removing the monitor pedestal base, you must lay the monitor face down on a soft area to prevent it from
getting scratched, defaced, or broken.
Cleaning the Monitor
The monitor is a high-quality optical device that requires special care when cleaning. To clean the monitor, follow
these steps:
1 Turn off the computer and the monitor.
2 Unplug your monitor from the wall outlet before cleaning.
CAUTION: Do not use benzene, thinner, ammonia, or any volatile substances to clean the monitor screen or
cabinet. These chemicals may damage the monitor. Do not use liquid cleaners or aerosol cleaners. Never use
water to clean an LCD screen.
3 Wipe the screen with a dry, soft, clean cloth.
• If the screen requires additional cleaning, use an antistatic screen cleaner.
4 Dust the monitor housing. Use a damp cloth to clean the cabinet.
• If the cabinet requires additional cleaning, use a clean cloth dampened with isopropyl alcohol.
5 Plug in the monitor.
6 Turn on the monitor and the computer.
5
Setup
Base and Tilt
Attaching the Base
1 Set the panel face down on a flat , protected surface , such as a table top.
2 Using both hands , align the base with the pedestal and push in firmly to lock in place.
Make sure that the base is securely locked in place before continuing with the setup procedure.
CAUTION: To prevent damage, avoid applying pressure to the panel front.
6
Removing the Base
1 Set the panel face-down on a flat, protected surface.
2 Squeeze the tabs in the bottom of the base to release the lock.
3 Remove the base from the pedestal.
CAUTION: To prevent damage, avoid applying pressure to the panel front.
Adjusting the Tilt
For optimal viewing, adjust the screen tilt to your own preference, as follows:
1 Face the front of the monitor and hold the stand so that you do not topple the monitor while changing the tilt.
2 Adjust the tilt by moving the monitor’s top edge toward or away from you.
CAUTION: To avoid breakage or other damage, do not touch the LCD screen while changing the tilt.
7
Cables
Attaching the Cables
1 Turn off your computer.
2 If you are attaching a VGA cable, connect one end of the 15-pin D-Sub VGA cable (blue connector) to the back of
the monitor and connect the other end to the computer VGA port.
3 If attaching a DVI cable, connect one end of the cable to the back of the monitor and connect the other end to the
computer.
8
4 Connect one end of the power cord to the back of the monitor and plug the other end into a grounded outlet.
5 Turn on your monitor and computer.
If your monitor displays an image, installation is complete. If it does not display an image,
see Technical Support FAQs and Using the Monitor.
9
Wall Mounting Arm
Preparing to Install a Wall Mounting Arm (Not supplied)
This monitor can be attached to a wall mounting arm that you purchase separately.
CAUTION: Before disassembling the monitor, turn off the monitor power, and disconnect all power, video, and
audio cables.
1 Disconnect the cables from the monitor.
2 With the panel face-down on a protected surface, remove the screws and the pedestal/base attachment.
3 Follow the manufacturer’s instructions to assemble the wall mounting arm.
Installing a Wall Mounting Arm
1 Set the monitor screen down on a flat, soft, protected surface.
2 Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the mounting holes in
the back of the monitor.
3 Insert four screws into the mounting holes and tighten.
4 Reconnect the cables. Refer to the user’s manual that came with the wall mounting arm (purchased separately)
for instructions on attaching it to the wall.
10
Using the Monitor
Operating Instructions
Control buttons are located on the front of the panel, as shown below. Use the Menu button (B) to adjust the display
settings to your personal preferences:
y Set up the monitor, attach the cables, and adjust the tilt as described in the Setup section above.
y Press the Power button (E) to turn the monitor on and off. The power indicator lights up when the monitor is on.
y The monitor must be turned on for the other control buttons to work.
y Set the resolution (Setting the Optimal Resolution) and adjust the volume (Adjusting the Volume).
y Adjust the onscreen display (OSD) settings (Adjusting On-screen Display Settings).
11
External Controls
A
Auto button
Automatically fine-tunes the image quality.
B
Menu button
Opens, selects, or exits the OSD menu.
C
– (minus) button
Navigates backward through the OSD menu and decreases adjustment levels.
If the OSD menu is inactive, activates the Volume decrease.
D
+ (plus) button
E
Power button
Navigates forward through the OSD menu and increases adjustment levels.
If the OSD menu is inactive, activates the Volume increase.
Turns the monitor on or off.
F
Power LED
Fully powered = green
Sleep mode = amber
Sleep timer mode = flashing amber
See Technical Support FAQs for more information.
12
Settings
Setting the Optimal Resolution
The recommended resolution for this monitor is 1366 x 768.To configure the monitor to this resolution, complete the
setup procedure and make sure that the monitor is connected to the computer. Turn the monitor on and do the
following:
1 Click the Windows Start Button®, and then click Control Panel.
2 Under Appearance and Personalization, click Adjust Screen Resolution.
3 Set the resolution slide bar to 1366 x 768.
NOTE: If 1366 x 768 is not shown, download the monitor driver from the Web. See Using the Monitor for instructions.
Adjusting the Volume
While the monitor is turned on but the OSD menu is inactive, press the volume increase and decrease (plus and
minus) buttons to adjust volume to the desired level. Volume can range from 0 (mute) to 100. The preset value is 50.
Locking and Unlocking the OSD
To change the lock status of the on-screen display (from locked to unlocked, or from unlocked to locked) press and
hold the Menu button for 10 seconds while the monitor is on. If the OSD is locked, the message “OSD Lock” displays
for 10 seconds.
13
Adjusting On-Screen Display Settings
Use the OSD menu to adjust the screen image and change settings. To access the OSD menu:
1 If the monitor is not already on, press the Power button to turn the monitor on.
2 Press the Menu button to activate the OSD menu.
3 Press the – (minus) and + (plus) buttons to navigate through the functions. Once the desired function is
highlighted, press the Menu button again to activate it. If the selected function has a sub-menu, it displays.
Press – (minus) or + (plus) again to navigate through the sub-menu functions. Once the desired sub-function is
highlighted, press the Menu button to activate it.
4 Press – (minus) or + (plus) to change the settings of the selected function.
5 To exit and save, select the Exit function. If you want to adjust another function, repeat steps 3–4.
NOTE: If the buttons remain untouched for 30 seconds while displaying a menu, new adjustments will be saved and
exit the menu.
14
OSD Menu
The table below shows the OSD menus and their functions at each level.
OSD Menu Levels
Level 1
Level 2
Level 3
Level 4
Factory Preset
Switch Video Input
(w185 / W185q only)
Brightness
Adjustment Scale
Y
Reset
Cancel
Save and Return
Contrast
Adjustment Scale
Y
Reset
Cancel
Save and Return
Image Control
Auto Adjustment
“Adjusting” Message
Y
Horizontal Position
Adjustment Scale
Y
Vertical Position
Adjustment Scale
Y
Custom Scaling
Fill to Screen
Fill to Aspect Ratio
Clock
Adjustment Scale
Y
Clock Phase
Adjustment Scale
Y
Cancel
Save and Return
Color
9300 K
6500 K
Custom Color
Y
Custom Color
Adjustment
Reset
Cancel
Save and Return
sRGB
Reset
Cancel
Save and Return
15
OSD Menu Levels (continued)
Level 1
Level 2
Quick View
Movie
Level 3
Level 4
Factory Preset
Photo
Gaming
Text
Y
Custom
Cancel
Save and Return
Language
Deutsch
简体中文
日本語
English
English
Español
Français
Italiano
Nederlands
Cancel
Save and Return
Volume(w185 only)
OSD
Control(w185 only)
Horizontal
OSD Position
Adjustment Scale
Y
Vertical
OSD Position
Adjustment Scale
Y
OSD Transparency
Adjustment Scale
Y
OSD Timeout
Adjustment Scale
Y
Cancel
Management
16
Power Saver
Save and Return
Y
Mode Display
On / Off Selection
Y
Power-On
Status Display
On / Off Selection
Y
DDC/CI Support
On / Off Selection
Y
Bezel Power LED
On / Off Selection
Y
Sleep Timer
Timer Set Menu
Y
Default Video Input
(w185 / W185q only)
Analog-VGA
Digital-DVI
Y
OSD Menu Levels (continued)
Level 1
Level 2
Level 3
Level 4
Factory Preset
Cancel
Save and Return
OSD Control
(v185w only)
Horizontal OSD
Position
Adjustment Scale
Y
Vertical OSD
Position
Adjustment Scale
Y
OSD Transparency
Adjustment Scale
Y
OSD Timeout
Adjustment Scale
Y
Cancel
Save and Return
Information
Factory Reset
Yes
No
Exit
17
Installing Drivers and Using the Auto-Adjustment Feature
Downloading Drivers and Software
To download the latest version of drivers and software files from the HP Support Web site:
1
2
3
4
5
Refer to: http://www.hp.com/support
Select your country/region.
Select Download Drivers and Software.
Enter the model number of your monitor. The software download pages for your monitor will be displayed.
Download and install the driver and software files using the instructions in the download pages.
Using the Auto-Adjustment Function
Press the Auto button to optimize the screen performance for VGA (analog).
If your monitor is using VGA (analog) input, auto-adjustment can correct the following image quality conditions:
y Fuzzy or unclear focus
y Ghosting, streaking, or shadowing effects
y Faint vertical bars
y Thin, horizontal scrolling lines
y An off-center picture
18
Technical Support FAQs
Technical Support FAQs (Frequently Asked Questions)
Problem & Question
Possible Solutions
Power LED is not on.
y Make sure the Power button is on and the power cord is properly
connected to a grounded power outlet and to the monitor.
No Plug & Play.
y In order for the Plug & Play feature of the monitor to work, you need a
Plug & Play compatible computer and video card. Check with your
computer manufacturer.
y Check the monitor’s video cable and make sure none of the pins are
bent.
y Make sure the HP monitor drivers are installed (HP monitor drivers are
available at: http://www.hp.com/support)
Picture is fuzzy and has ghosting
shadowing problem.
y Adjust the contrast and brightness controls.
y Make sure you are not using an extension cable or switch box. We
recommend plugging the monitor directly into the video card output
connector on the back of your computer.
y For VGA input, the auto-adjustment function may fix this problem.
Picture bounces, flickers or wave
pattern is present in the picture.
y Move electrical devices that may cause electrical interference as far
away from the monitor as possible.
y Use the maximum refresh rate your monitor is capable of at the
resolution you are using.
Monitor is stuck in “Active Off-Mode”.
y The computer power switch should be in the on position.
y The computer video card should be snugly seated in its slot.
y Make sure the monitor’s video cable is properly connected to the
computer.
y Inspect the monitor’s video cable and make sure none of the pins are
bent.
y Make sure your computer is operational by hitting the Caps Lock key
on the keyboard while observing the Caps Lock LED. The LED should
either turn on or off after hitting the Caps Lock key.
19
Technical Support FAQs (Frequently Asked Questions) (continued)
Problem & Question
Possible Solutions
Missing one of the primary colors (red,
green, or blue).
y Inspect the monitor’s video cable and make sure that none of the pins
are bent.
y Make sure the monitor’s video cable is properly connected to the
computer.
Screen image is not centered or sized
properly.
y Adjust horizontal and vertical screen position.
y For VGA input, the auto-adjustment function may fix this problem.
Picture has color defects (white does
not look white).
y Adjust RGB color or select color temperature.
Unable to set the monitor to the
optimal resolution.
y Make sure that the graphics card supports the optimal resolution (1366
x 768).
y Make sure that the latest supported driver is installed for the graphics
card. For HP and Compaq systems, you can download the latest
graphics driver for your system from:
http://www.hp.com/support
y For other systems, refer to the Web site for your graphics card.
20
Specifications
All specifications represent the typical specifications provided by HP’s component manufacturers; actual
performance may vary either higher or lower.
v185e / v185es / v185w / v185ws / w185 / W185q
Display Type
18.51 inches, TFT LCD
47 cm
Viewable Image Size
18.51 -inch diagonal
47 cm
Tilt
–5° to 20°
Face Treatment
Antiglare polarizer with hard coating (select
models only)
Maximum Weight (unpacked)
8.47 lb.
3.8 kg
Dimensions (including pedestal)
Height
Depth
Width
13.54 inches
7.05 inches
17.4 inches
344 mm
179 mm
442 mm
Optimum Display Resolution
1366 x 768 (60 Hz)
Text Mode
720 x 400
Dot Pitch
0.3 (H) x 0.3 (V) mm(v185w/ v185ws/ w185)
0.1 (H) x 0.3 (V) mm(v185e/v185es/W185q)
Horizontal Frequency
24 to 83 kHz (v185e / v185es / W185q)
30 to 64 kHz (v185w / v185ws / w185)
Vertical Refresh Rate
48 to 76 Hz (v185e / v185es / W185q)
50 to 76 Hz (v185w / v185ws / w185)
Audio Power Output
2W / channel @ PC 1 Vrms
Speaker (R/L)
2W / 4 ohm speaker
Power Consumption
<30 watts typical(v185w / v185ws / w185)
<33 watts typical(v185e / v185es / W185q)
Input Terminal
VGA connector or DVI connector
Environmental Requirements
Temperature:
Operating
Non-operating
41 to 95°F
–29 to 140°F
Relative Humidity
20 to 85% (non-condensing)
Power Source
100–240 V∿, 50 / 60 Hz
Altitude:
Operating
Non-operating
0 to 6,561.68 feet
0 to 40,000 feet
5 to 35°C
–20 to +60°C
0 to 2,000 m
0 to12,192 m
21
Preset Display Modes
Preset
22
Pixel Format
Horz Freq
(kHz)
Horz
Polarity
Vert Freq
(Hz)
Vert Polarity
Pixel Clk
(MHz)
Source
1
640 x 480
31.469
-
59.940
-
25.175
VGA
2
640 x 480
37.861
-
72.809
-
31.500
VESA
3
640 x 480
37.500
-
75.000
-
31.500
VESA
4
720 x 400
31.469
-
70.087
+
28.322
VGA
5
800 x 600
37.87
+
60.317
+
40.000
VESA
6
800 x 600
48.077
+
72.188
+
50.000
VESA
7
800 x 600
46.875
+
75.000
+
49.500
VESA
8
832 x 624
49.726
+
74.551
+
57.284
MAC
9
1024x768
48.36
-
60.00
-
65.000
VESA
10
1024x768
56.476
-
70.069
-
75.000
VESA
11
1024x768
60.02
+
75.03
+
78.750
VESA
12
1280 x 720
44.77
-
59.86
+
74.5
13
1366 x 768
47.712
-
59.79
+
85.5
CVT
0.98M9-R
CVT
Power Cord Set Requirements
The monitor power supply is provided with automatic line switching (ALS). This feature allows the monitor to operate
on input voltages in the range of 100–240V∿, 50 / 60 Hz, 1.5A.
The power cord set (flexible cord or wall plug) received with the monitor meets the requirements for use in the
country/region where the equipment was purchased.
If you need to obtain a power cord for a different country/region, you should purchase a power cord that is approved
for use in that country/region.
The power cord must be rated for the product and for the voltage and current marked on the product’s electrical
ratings label. The voltage and current rating of the cord should be greater than the voltage and current rating marked
on the product. In addition, the cross-sectional area of the wire must be a minimum of 0.75 mm² or 18AWG, and the
length of the cord must be between 4.94 ft (1.5 m) and 12 ft (3.6 m). If you have questions about the type of power
cord to use, contact your HP-authorized service provider.
A power cord should be routed so that it is not likely to be walked on or pinched by items placed upon it or against it.
Particular attention should be paid to the plug, electrical outlet, and the point where the cord exits from the product.
VGA Pin Assignments
Pin Number
15-Pin Side of the Signal
Cable
1
Video-Red
2
Video-Green
3
Video-Blue
4
Ground
5
Detect Cable
6
GND-R
7
GND-G
8
GND-B
9
+5V
10
Ground
11
Ground
12
DDC-Serial data
13
H-sync
14
V-sync
15
DDC-Serial clock
DVI Pin Assignments
23
Plug and Play DDC2B Feature
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the
monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional
information about its display capabilities.
The DDC2B is a bi-directional data channel based on the I²C protocol. The host can request EDID information over
the DDC2B channel.
LCD Monitor Quality and Pixel Policy
The HP LCD Monitor uses high-precision technology, manufactured according to high standards, to help guarantee
trouble-free performance. Nevertheless, the display may have cosmetic imperfections that appear as small bright or
dark spots. This is common to all LCD displays used in products supplied by all vendors and is not specific to the HP
LCD Monitor. These imperfections are caused by one or more defective pixels or subpixels.
y A pixel consists of one red, one green, and one blue subpixel.
y A defective whole pixel is always turned on (a bright spot on a dark background), or it is always off (a dark spot on
a bright background). The first is the more visible of the two.
y A defective subpixel (dot defect) is less visible than a defective whole pixel and is small and only visible on a
specific background.
To locate defective pixels, the monitor should be viewed under normal operating conditions and in normal operating
mode at a supported resolution and response rate, from a distance of approximately 50 cm (16 in).
We expect that, over time, the industry will continue to improve its ability to produce displays with fewer cosmetic
imperfections, and we will adjust guidelines as improvements are made.
For more information about your v185e / v185es / v185w / v185ws / w185 / W185q Monitor, refer to the HP Web site
at: http://www.hp.com/support
Agency Regulatory Notices
Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
y Reorient or relocate the receiving antenna.
y Increase the separation between the equipment and the receiver.
y Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
y Consult the dealer or an experienced radio or television technician for help.
24
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are not
expressly approved by Hewlett-Packard Company may void the user’s authority to operate the equipment.
Cables
Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods to maintain
compliance with FCC rules and regulations.
Declaration of Conformity for Products Marked with FCC Logo, United States Only
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
For questions regarding your product, contact:
Hewlett-Packard Company
P. O. Box 692000, Mail Stop 530113
Houston, Texas 77269-2000
Or
call: 1-(800)-474-6836
For questions regarding this FCC declaration, contact:
Hewlett-Packard Company
P. O. Box 692000, Mail Stop 510101
Houston, Texas 77269-2000
Or
call: 1-(281)-514-3333
To identify this product, refer to the part, series, or model number found on the product.
Canadian Notice
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Avis Canadien
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du
Canada.
25
European Union Regulatory Notice
This product complies with the following EU directives:
y Low Voltage Directive 2006/95/EC
y EMC Directive 2004/108/EC
Compliance with these directives implies conformity to applicable harmonized European standards (European
Norms) which are listed on the EU Declaration of Conformity issued by Hewlett-Packard for this product or product
family.
This compliance is indicated by the following conformity marking placed on the product:
xxxx*
This marking is valid for non-Telecom products and EU
harmonized Telecom products (e.g., Bluetooth).
This marking is valid for EU non-harmonized Telecom products.
*Notified body number (used only if applicable — refer to the
product label).
Hewlett-Packard GmbH, HQ-TRE, Herrenberger Straße 140, 71034 Böblingen, Germany
26
Disposal of Waste Equipment by Users in Private Households in the European
Union
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other
household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a
designated collection point for the recycling of waste electrical and electronic equipment. The separate collection
and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that
it is recycled in a manner that protects human health and the environment. For more information about where you
can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal
service or the shop where you purchased the product.
Japanese Notice
27
Japanese Power Cord Notice
Japanese Material Content Declaration
A Japanese regulatory requirement, defined by Specification JIS C 0950, 2005, mandates that manufacturers
provide Material Content Declarations for certain categories of electronic products offered for sale after July 1, 2006.
To view the JIS C 0950 material declaration for this product, visit www.hp.com/go/jisc0950.
Korean Notice
Materials Disposal
This HP product contains Mercury in the fluorescent lamp in the display LCD that might require special handling at
end-of-life.
Disposal of this material can be regulated because of environmental considerations. For disposal or recycling
information, please contact your local authorities or the Electronic Industries Alliance (EIA) (www.eiae.org).
Chemical Substances
HP is committed to providing our customers with information about the chemical substances in our products as
needed to comply with legal requirements such as REACH (Regulation EC No 1907/2006 of the European
Parliament and the Council). A chemical information report for this product can be found
at:http://www.hp.com/go/reach
28
HP Recycling Program EPA
HP offers product end-of-life return programs for HP and other manufacturers’ hardware in several geographic areas.
The terms and availability of these programs vary by geography because of differences in regulatory requirements
and local customer demand. For information on the HP recycling program, refer to the HP Web site at:
http://www.hp.com/recycle
EPA ENERGY STAR® Compliance
Products marked with the ENERGY STAR® logo on the packaging box qualify with the U.S. Environmental
Protection Agency’s ENERGY STAR® guidelines for energy efficiency.
Products with the ENERGY STAR® label are designed to use less energy, help you save money on utility bills, and
help protect the environment.
ENERGY STAR® is a registered trademark owned by the U.S. government.
29
30
Part number: 506356-002