HP NC7770 User guide

Add to my manuals
22 Pages

advertisement

HP NC7770 User guide | Manualzz
HP NC7770 PCI-X
Gigabit Server Adapter
User Guide
June 2007 (Second Edition)
Part Number 336419-00B
© 2003, 2007 Hewlett-Packard Development Company, L.P.
Broadcom® is a registered trademark of Broadcom Corporation and/or its subsidiaries.
Hewlett-Packard Company shall not be liable for technical or editorial errors or omissions contained herein. The
information in this document is provided “as is” without warranty of any kind and is subject to change without
notice. The warranties for HP products are set forth in the express limited warranty statements accompanying such
products. Nothing herein should be construed as constituting an additional warranty.
Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with
FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical
Data for Commercial Items are licensed to the U.S. Government under vendor's standard commercial license.
HP NC7770 PCI-X Gigabit Server Adapter User Guide
June 2007 (Second Edition)
Part Number 336419-00B
HP Contents
About This Guide
Technician Notes...........................................................................................................................................v
Where to Go for Additional Help.................................................................................................................vi
Telephone Numbers ...............................................................................................................................vi
Chapter 1
Introduction
Overview ................................................................................................................................................... 1-1
Hardware Overview .................................................................................................................................. 1-1
LED Indicators .......................................................................................................................................... 1-2
UTP Category 5 Cable .............................................................................................................................. 1-2
Chapter 2
Installing the Adapter
Overview ................................................................................................................................................... 2-1
Electrostatic Discharge Precautions .......................................................................................................... 2-1
Installing the Adapter in a Server.............................................................................................................. 2-2
Connecting the Network Cable ................................................................................................................. 2-3
Appendix A
Regulatory Notice
Federal Communications Commissions Notice ....................................................................................... A-1
Class A Equipment ............................................................................................................................ A-1
Class B Equipment............................................................................................................................. A-2
Modifications ..................................................................................................................................... A-2
Cables................................................................................................................................................. A-2
Canadian Notice (Avis Canadien) ............................................................................................................ A-3
Class A Equipment ............................................................................................................................ A-3
Class B Equipment............................................................................................................................. A-3
European Union Notice ............................................................................................................................ A-4
BSMI Notice............................................................................................................................................. A-4
Japanese Notice ........................................................................................................................................ A-5
PCI-X Notice............................................................................................................................................ A-5
Appendix B
Electrostatic Discharge
Overview ...................................................................................................................................................B-1
Grounding Methods...................................................................................................................................B-1
HP NC7770 PCI-X Gigabit Server Adapter User Guide
iii
Contents
Appendix C
Specifications
NC7770 PCI-X Gigabit Server Adapter Specifications............................................................................ C-1
UTP Cable Specifications ......................................................................................................................... C-2
Using UTP Category 5 Cable in Gigabit Over Copper Installations.................................................. C-2
RJ-45 Pinouts and Crossover Function..................................................................................................... C-2
10/100 Straight-Through Pinouts ....................................................................................................... C-2
10/100 Crossover Pinouts................................................................................................................... C-3
Gigabit over Copper Internal Straight- Through Pinouts ................................................................... C-4
Gigabit over Copper External Crossover Pinouts............................................................................... C-4
iv
HP NC7770 PCI-X Gigabit Server Adapter User Guide
About This Guide
Use this guide as reference when installing and maintaining the HP NC7770 PCI-X Gigabit
Server Adapter.
WARNING: To reduce the risk of personal injury from electric shock and hazardous
energy levels, only authorized service technicians should attempt to repair this
equipment. Improper repairs can create conditions that are hazardous.
Technician Notes
WARNING: Only authorized technicians trained by HP should attempt to repair this
equipment. All troubleshooting and repair procedures are detailed to allow only
subassembly/module-level repair. Because of the complexity of the individual boards
and subassemblies, no one should attempt to make repairs at the component level or
to make modifications to any printed wiring board. Improper repairs can create a safety
hazard.
WARNING: To reduce the risk of personal injury from electric shock and hazardous
energy levels, do not exceed the level of repairs specified in these procedures.
Because of the complexity of the individual boards and subassemblies, do not attempt
to make repairs at the component level or to make modifications to any printed wiring
board. Improper repairs can create conditions that are hazardous.
WARNING: To reduce the risk of electric shock or damage to the equipment:
•
Disconnect power from the system by unplugging all power cords from the power
supplies.
•
Do not disable the power cord grounding plug. The grounding plug is an important
safety feature.
•
Plug the power cord into a grounded (earthed) electrical outlet that is easily
accessible at all times.
CAUTION: To properly ventilate the system, you must provide at least 7.6 cm (3.0 in.) of
clearance at the front and back of the server.
CAUTION: The computer is designed to be electrically grounded (earthed). To ensure proper
operation, plug the AC power cord into a properly grounded AC outlet only.
HP NC7770 PCI-X Gigabit Server Adapter User Guide
v
About This Guide
NOTE: Any indications of component replacement or printed wiring board modifications may void any
warranty.
Where to Go for Additional Help
HP updates networking software frequently to include new functionality and features.
Complete the following steps to get the latest drivers, firmware, and documentation.
1. Go to the HP website (http://www.hp.com).
2. Click Support and Troubleshooting Information from the left menu bar.
3. Type the product name in the for product box and press Enter. For example, type
NC370T.
4. Download the drivers, firmware, or documentation as needed.
Telephone Numbers
For the name of your nearest HP authorized reseller:
•
In the United States, call 1-800-345-1518.
•
In Canada, call 1-800-263-5868.
For HP technical support:
•
In the United States and Canada, call 1-800-652-6672.
•
Outside the United States and Canada, refer to
www.hp.com
vi
HP NC7770 PCI-X Gigabit Server Adapter User Guide
1
Introduction
Overview
The HP NC7770 PCI-X Gigabit Server Adapter is a high-performance Ethernet adapter with
a fully integrated 10/100/1000 controller that delivers up to 1000 Mb/s Ethernet over
twisted-pair (copper) cabling. The HP NC7770 adapter has one auto-negotiating RJ-45 port
and LED indicators showing link, activity, and port speed. The NC7770 PCI-X Gigabit
Server Adapter is a supported option for selected HP ProLiant servers.
For the latest functionality, features, and operating system support for this server adapter,
refer to the networking page at
(http://h18004.www1.hp.com/products/servers/networking/index-nic.html)
Hardware Overview
The NC7770 Server Adapter has one auto-negotiating 10/100/1000 RJ-45 port. LED
indicators show link, activity, and port speed. See Table 1-1 for descriptions of LED
operations.
Figure 1-1: RJ-45 port and LED locations
HP NC7770 PCI-X Gigabit Server Adapter User Guide
1-1
Introduction
LED Indicators
The following table describes the LED indicators located on the front panel of the HP
NC7770 Server Adapter.
Table 1-1: 10/100/1000 LED Operations for the NC7770 Adapter
LED
Display
Description
1000
On
Link to the adapter is established. The adapter is sending or receiving
network data at 1000 Mb/s.
Off
The adapter is not sending or receiving network data at 1000 Mb/s.
On
Link to the adapter is established. The adapter is sending or receiving
network data at 100 Mb/s.
Off
The adapter is not sending or receiving network data at 100 Mb/s.
On
Link to the adapter is established. The adapter is sending or receiving
network data at 10 Mb/s.
Off
The adapter is not sending or receiving network data at 10 Mb/s.
On
The adapter is sending or receiving network data at 10, 100, or 1000
Mb/s, as indicated by the 10, 100, and 1000 LEDs. The adapter is
receiving power, and the cable connection is functional.
Off
No network data is being sent or received. The adapter is not receiving
power, the cable connection is faulty, or the driver is not loaded.
100
10
ACT
UTP Category 5 Cable
The NC7770 Server Adapter can use existing Category 5 UTP (or better) cable to deliver
Gigabit Ethernet over copper, according to the IEEE 802.3ab specifications. For new
installations, Category 5e cable is recommended. For troubleshooting and other information
about cabling, see, “UTP Cable Specifications” in Appendix C.
1-2
HP NC7770 PCI-X Gigabit Server Adapter User Guide
2
Installing the Adapter
Overview
This chapter describes installation precautions and explains how to install the adapter. It also
describes how to connect the network cable.
WARNING: To avoid the risk of personal injury or damage to the equipment, consult
the safety information and user documentation provided with your equipment before
attempting installation of the adapter.
Many servers are capable of producing energy levels that are considered hazardous.
Users should not remove enclosures, nor should they bypass the interlocks provided
for removal of these hazardous conditions.
Installation of this adapter should be performed by individuals who are both qualified in
the servicing of computer equipment, and trained in the hazards associated with
products capable of producing hazardous energy levels.
NOTE: Before removing the cover of your server, refer to the HP documentation for the proper
methods for installing a PCI card and avoiding electric shock hazards.
Electrostatic Discharge Precautions
A discharge of static electricity from a finger or other conductor can damage components on
the adapter. This can make the adapter inoperable. In addition to the following information,
see Appendix B for more precautions.
To prevent electrostatic damage, observe the following precautions:
•
Always properly ground yourself when touching a static-sensitive component or
assembly.
•
Avoid hand contact by transporting and storing parts in static-safe containers.
•
Keep electrostatic-sensitive parts in their containers until they arrive at static-free
locations.
•
Place containers on a grounded surface before removing the contents.
•
Avoid touching pins, leads, or circuitry.
HP NC7770 PCI-X Gigabit Server Adapter User Guide
2-1
Installing the Adapter
Installing the Adapter in a Server
Refer to the HP ProLiant server documentation for additional information on how to safely
install a PCI card in your server.
Figure 2-1: Installing the adapter in a server
WARNING: If the server is not PCI Hot Plug compliant, power it down and unplug the
power cord from the power outlet before removing the server cover. Failure to do so
may damage the adapter or server.
1. Remove the server cover and cover bracket from a PCI slot.
WARNING: To reduce the risk of personal injury from hot surfaces, allow the internal
system components to cool before touching them.
2. Firmly seat the adapter in the PCI slot and secure the adapter bracket.
3. Replace the server cover and plug in the power cord.
2-2
HP NC7770 PCI-X Gigabit Server Adapter User Guide
Installing the Adapter
Connecting the Network Cable
Network connections for the NC7770 Server Adapter can employ existing Category 5 UTP
(or better) cable for Gigabit over copper transmissions. For new installations, Category 5e
(enhanced Category 5) or better cable is recommended.
To secure the cable, plug the cable connector into the RJ-45 port. Ensure that the tab on the
plug clicks into position indicating that it is properly seated.
For more information, see “UTP Cable Specifications” in Appendix C.
HP NC7770 PCI-X Gigabit Server Adapter User Guide
2-3
A
Regulatory Notice
Federal Communications Commissions Notice
Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has
established Radio Frequency (RF) emission limits to provide an interference-free radio
frequency spectrum. Many electronic devices, including computers, generate RF energy
incidental to their intended function and are, therefore, covered by these rules. These rules
place computers and related peripheral devices into two classes, A and B, depending upon
their intended installation. Class A devices are those that may reasonably be expected to be
installed in a business or commercial environment. Class B devices are those that may
reasonably be expected to be installed in a residential environment (i.e., personal computers).
The FCC requires devices in both classes to bear a label indicating the interference potential
of the device as well as additional operating instructions for the user.
The rating label on the device shows which class (A or B) the equipment falls into. Class B
devices have an FCC logo or FCC ID on the label. Class A devices do not have an FCC logo
or FCC ID on the label. Once the class of the device is determined, refer to the following
corresponding statement.
Class A Equipment
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference, in which case the user will be required to correct the interference at
personal expense.
HP NC7770 PCI-X Gigabit Server Adapter User Guide
A-1
Regulatory Notice
Class B Equipment
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
•
Consult the dealer or an experienced radio or television technician for help.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this
device that are not expressly approved by Hewlett-Packard Company may void the user's
authority to operate the equipment.
Cables
Connections to this device must be made with shielded cables with metallic RFI/EMI
connector hoods in order to maintain compliance with FCC Rules and Regulations.
Declaration of Conformity for products marked with the FCC logo - United States only
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
For questions regarding your product, contact:
Hewlett-Packard Company
P. O. Box 692000, Mail Stop 530113
Houston, Texas 77269-2000
Or, call
1-800- 652-6672. For continuous quality improvement, calls may be recorded or monitored.
A-2
HP NC7770 PCI-X Gigabit Server Adapter User Guide
Regulatory Notice
For questions regarding this FCC declaration, contact:
Hewlett-Packard Company
P. O. Box 692000, Mail Stop 510101
Houston, Texas 77269-2000
Or, call
(281) 514-3333
To identify this product, refer to the Part, Series, or Model number found on the product.
Canadian Notice (Avis Canadien)
Class A Equipment
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
Class B Equipment
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
HP NC7770 PCI-X Gigabit Server Adapter User Guide
A-3
Regulatory Notice
European Union Notice
Products bearing the CE marking comply with the EMC Directive (89/336/EEC) and the Low
Voltage Directive (73/23/EEC) issued by the Commission of the European Community and if
this product has telecommunication functionality, the R&TTE Directive (1999/5/EC).
Compliance with these directives implies conformity to the following European Norms (in
parentheses are the equivalent international standards and regulations):
•
EN 55022 (CISPR 22)—Electromagnetic Interference
•
EN55024 (IEC61000-4-2, 3, 4, 5, 6, 8, 11)—Electromagnetic Immunity
•
EN61000-3-2 (IEC61000-3-2)—Power Line Harmonics
•
EN61000-3-3 (IEC61000-3-3)—Power Line Flicker
•
EN 60950 (IEC 60950)—Product Safety
BSMI Notice
A-4
HP NC7770 PCI-X Gigabit Server Adapter User Guide
Regulatory Notice
Japanese Notice
PCI-X Notice
When this product is used in PCI-X mode, it is a “Class A” device.
HP NC7770 PCI-X Gigabit Server Adapter User Guide
A-5
B
Electrostatic Discharge
Overview
To prevent damage to the system, be aware of the precautions you need to follow when
setting up the system or handling parts. A discharge of static electricity from a finger or other
conductor may damage system boards or other static-sensitive devices. This type of damage
may reduce the life expectancy of the device.
To prevent electrostatic damage, observe the following precautions:
•
Avoid hand contact by transporting and storing products in static-safe containers.
•
Keep electrostatic-sensitive parts in their containers until they arrive at static-free
workstations.
•
Place containers on a grounded surface before removing the contents.
•
Avoid touching pins, leads, or circuitry.
•
Always be properly grounded when touching a static-sensitive component or assembly.
Grounding Methods
There are several methods for grounding. Use one or more of the following methods when
handling or installing electrostatic-sensitive parts:
•
Use a wrist strap connected by a ground cord to a grounded workstation or computer
chassis. Wrist straps are flexible straps with a minimum of 1 megohm ±10 percent
resistance in the ground cords. To provide proper ground, wear the strap snug against the
skin.
•
Use heel straps, toe straps, or boot straps at standing workstations. Wear the straps on
both feet when standing on conductive floors or dissipating floor mats.
•
Use conductive field service tools.
•
Use a portable field service kit with a folding static-dissipating work mat.
If you do not have any of the suggested equipment for proper grounding, have a HP
authorized reseller install the part.
NOTE: For more information on static electricity or assistance with product installation, contact your HP
authorized reseller.
HP NC7770 PCI-X Gigabit Server Adapter User Guide
B-1
C
Specifications
NC7770 PCI-X Gigabit Server Adapter Specifications
Table C-1: NC7770 PCI-X Gigabit Server Adapter Specifications
Specification
Description
Network Controller Chipset
Broadcom® 5701KHB
Data Transfer Method
64-bit/133MHz PCI-X, compatible with 64-bit/66MHz or
32-bit/66MHz Bus Master DMA
Power Requirement
Operating Voltage: +5V +/- 5%
Power Consumption: 10 Watts
Maximum: 2A @ 5V(DC)
Standards Supported
IEEE 802.3ab, 802.3u, 802.1p, 802.1z
Dimensions
6.6 x 2.5 inches (L x W), 16.5 cm x 6.4 cm
Connector and distances
10BASE-T: Category 3, 4 or 5 UTP 100 Meters (328 feet)
100BASE-TX: Category 5 UTP 100 Meters (328 feet)
1000BASE-TX: Category 5 UTP 100 Meters (328 feet)
Interrupts Supported
Automatically configured
Temperature Range
Operating: 0°C to 55°C / 32°F to 131°F
Storage: -65°C to 85°C / -85°F to 185°F
Relative Humidity
Operating; 5% to 85%
Storage: 5% to 95%
Emissions Classifications
When used in PCI slot: FCC Class B
When used in PCI-X slot: FCC Class A
European Classifications
EN 55022 (CISPR 22)
EN 50082-1 (IEC 801-2, IEC 801-3, IEC 801-4)
VCCI
Safety Compliance
CE Mark
EN 60590
HP NC7770 PCI-X Gigabit Server Adapter User Guide
C-1
Specifications
UTP Cable Specifications
To connect to the network, the NC7770 Server Adapter uses the following cable for
1000BASE-T transmission.
Category 5 UTP or better
22-26 AWG, 100Ω @ 1MHz
EIA/TIA 568a or EIA/TIA 568b
Using UTP Category 5 Cable in Gigabit Over Copper Installations
For Gigabit over copper installations, Category 5 UTP or better 1000BASE-T cable must
comply with the IEEE 802.3ab 1000BASE-T standard. For new installations, Category 5e
(enhanced Category 5) or better cable is recommended.
RJ-45 Pinouts and Crossover Function
The Ethernet standard also specifies that each segment implement a crossover function to
connect the transmitter of one device to the receiver of a device at the other end, and viceversa. The crossover function may be implemented internally at the hub or switch, or
externally through the twisted-pair media.
10/100 Straight-Through Pinouts
If the crossover function is implemented internally, the port is labeled MDI-X (Medium
Dependent Interface-Crossover). When an MDI-X port is connected to an MDI port, the
twisted pair media should be wired straight-through using the physical pinouts indicated in
Table C-2.
Table C-2: 10/100 Pinouts Using Internal, Straight-Through Crossover
Pin
Function
Color Match
Function
Pin
1
TD+
White/Orange
TD+
1
2
TD-
Orange/White
TD-
2
3
RD+
White/Green
RD+
3
4
Blue/White
4
5
White/Blue
5
6
RD-
Green/White
RD-
6
7
White/Brown
7
8
Brown/White
8
Figure C-1 shows the straight-through 10/100 connector wiring to be used when the crossover
function is implemented on the hub or switch.
C-2
HP NC7770 PCI-X Gigabit Server Adapter User Guide
Specifications
Figure C-1: 10/100 straight-through wiring for RJ-45 connector
10/100 Crossover Pinouts
When the crossover function is not provided within the hub or switch, you must implement
the crossover through the twisted-pair media using the physical pinouts indicated in
Table C-3.
Table C-3: 10/100 Pinouts Using External Crossover
Pin
Function
Color/Match
Function
Pin
1
TD+
White/Orange
RD+
3
2
TD-
Orange/White
RD-
6
3
RD+
White/Green
TD+
1
TD-
2
4
Blue/White
5
White/Blue
6
RD-
Green/White
7
White/Brown
8
Brown/White
Figure C-2 shows the correct wiring to use when the crossover function is implemented
externally in the twisted-pair cabling.
Figure C-2: 10/100 external crossover for RJ-45 connector
HP NC7770 PCI-X Gigabit Server Adapter User Guide
C-3
Specifications
Gigabit over Copper Internal StraightThrough Pinouts
Unlike connections in which the crossover function is implemented internally at the hub or
switch, the NC7770 Server Adapter provides its own automatic crossover function. This
means you can wire twisted-pair media straight-through for adapter-to-hub, adapter-toswitch, or adapter-to-adapter connections using the pinouts shown in Table C-4.
NOTE: To operate at Gigabit speeds, all four pairs of wires must be terminated within the RJ-45
connector.
Table C-4: Gigabit over Copper Pinouts Using Internal Crossover
Pin
Function
Color Match
Function
Pin
1
BI_DA+
White/Orange
BI_DA+
1
2
BI_DA-
Orange/White
BI_DA-
2
3
BI_DB+
White/Green
BI_DB+
3
4
BI_DC+
Blue/White
BI_DC+
4
5
BI_DC-
White/Blue
BI_DC-
5
6
BI_DB-
Green/White
BI_DB-
6
7
BI_DD+
White/Brown
BI_DD+
7
8
BI_DD-
Brown/White
BI_DD-
8
Figure C-3 shows straight-through Gigabit over copper connector wiring to be used when the
crossover function is implemented within the hub or switch.
Figure C-3: Gigabit straight-through wiring for RJ-45 connector
Gigabit over Copper External Crossover Pinouts
When a crossover function is not provided by the adapter, hub or switch, you must implement
it through the twisted-pair media using the physical pinouts shown in Table C-5.
C-4
HP NC7770 PCI-X Gigabit Server Adapter User Guide
Specifications
Table C-5: Gigabit over Copper Crossover Pinouts
Pin
Function
Color Match
Function
Pin
1
BI_DA+
White/Orange
BI_DB+
3
2
BI_DA-
Orange/White
BI_DB-
6
3
BI_DB+
White/Green
BI_DA+
1
4
BI_DC+
Blue/White
BI_DD+
7
5
BI_DC-
White/Blue
BI_DD-
8
6
BI_DB-
Green/White
BI_DA-
2
7
BI_DD+
White/Brown
BI_DC+
4
8
BI_DD-
Brown/White
BI_DC-
5
Figure C-4 shows the correct Gigabit over copper wiring to be used when the crossover
function is implemented externally in the twisted-pair cabling.
Figure C-4: Gigabit over copper external crossover for RJ-45
connector
HP NC7770 PCI-X Gigabit Server Adapter User Guide
C-5

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement