HP ProCurve Series 6600 User's Manual

Installation and
Getting Started Guide
HP ProCurve
Series 6600 Switches
www.procurve.com
ProCurve Series 6600 Switches
Installation and Getting Started Guide
© Copyright 2009 Hewlett-Packard Development
Company, L.P.
Disclaimer
HEWLETT-PACKARD COMPANY MAKES NO WARRANTY
OF ANY KIND WITH REGARD TO THIS MATERIAL,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not
be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing,
performance, or use of this material.
Publication Number
5992-4962
January 2009
Applicable Products
HP ProCurve 6600-24G Switch
HP ProCurve 6600-24G-4XG Switch
HP ProCurve 6600-24XG Switch
HP ProCurve Switch Power Supply
HP ProCurve Switch Fan Tray
(J9263A)
(J9264A)
(J9265A)
(J9269A)
(J9271A)
The information contained herein is subject to change
without notice. The only warranties for HP products and
services are set forth in the express warranty statements
accompanying such products and services. Nothing herein
should be construed as constituting an additional warranty.
HP shall not be liable for technical or editorial errors or
omissions contained herein.
Hewlett-Packard assumes no responsibility for the use or
reliability of its software on equipment that is not furnished
by Hewlett-Packard.
Warranty
See the Customer Support/Warranty booklet included with
the product.
A copy of the specific warranty terms applicable to your
Hewlett-Packard products and replacement parts can be
obtained from your HP Sales and Service Office or
authorized dealer.
Safety
Before installing and operating these products, please read
the “Installation Precautions” in chapter 2, “Installing the
Switch”, and the safety statements in appendix C, “Safety
and EMC Regulatory Statements”.
Hewlett-Packard Company
8000 Foothills Boulevard, m/s 5552
Roseville, California 95747-5552
www.procurve.com
Contents
1 Introducing the Switch
Front of the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Network Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
LED Power Save Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
LED Mode Select Button and Indicator LEDs . . . . . . . . . . . . . . . . . . . . 1-8
Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
Clear Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
Console Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
Back of the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
Power Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
Switch Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
2 Installing the Switch
Included Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Installation Precautions: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Installation Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
1. Prepare the Installation Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
2. Verify the Switch Passes Self Test . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
LED Behavior: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
3. (Optional) Reversing the air flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
4. Mount the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Rack or Cabinet Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
5. Connect the Switch to a Power Source . . . . . . . . . . . . . . . . . . . . . . 2-14
Securing the power cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
6. (Optional) Install or Remove mini-GBICs or SFPs . . . . . . . . . . . . .
Installing the Mini-GBICs or SFP+ Transceivers: . . . . . . . . . . . .
SFP and SFP+ transceivers Plug-in, Fault and Alert behaviors.
Removing the mini-GBICs: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-15
2-16
2-17
2-17
iii
7. Connect the Network Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
Using the RJ-45 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
Connecting Cables to mini-GBICs . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
8. (Optional) Connect a Console to the Switch . . . . . . . . . . . . . . . . . .
Terminal Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Direct Console Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Console Cable Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-19
2-19
2-20
2-21
Sample Network Topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22
3 Getting Started With Switch Configuration
Recommended Minimal Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Using the Console Setup Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Where to Go From Here . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
To Recover from a Lost Manager Password . . . . . . . . . . . . . . . . . . . . . 3-4
Using the IP Address for Remote Switch Management . . . . . . . . . . . . . . . . 3-5
Starting a Telnet Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Starting a Web Browser Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
4 Replacing Components
Replacing the fan tray assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Replacing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Installing a New Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Replacing the Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
5 Troubleshooting
Basic Troubleshooting Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Diagnosing with the LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Proactive Networking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
Hardware Diagnostic Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
Testing the Switch by Resetting It . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
Checking the Switch LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
Checking Console Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
Testing Twisted-Pair Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
Testing Switch-to-Device Network Communications . . . . . . . . . . . . 5-10
iv
Testing End-to-End Network Communications . . . . . . . . . . . . . . . . . 5-10
Restoring the Factory Default Configuration . . . . . . . . . . . . . . . . . . . . . . . 5-11
Downloading New Switch Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
HP Customer Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
Before Calling Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
A Specifications
Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Acoustic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
B Cabling and Technology Information
Cabling specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Technology distance specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3
Mode Conditioning Patch Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4
Installing the Patch Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5
Twisted-Pair Cable/Connector Pin-Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6
Straight-Through Twisted-Pair Cable for
10 Mbps or 100 Mbps Network Connections . . . . . . . . . . . . . . . . . . . . B-7
Cable Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-7
Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-7
Crossover Twisted-Pair Cable for
10 Mbps or 100 Mbps Network Connection . . . . . . . . . . . . . . . . . . . . . B-8
Cable Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-8
Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-8
Straight-Through Twisted-Pair Cable for
1000 Mbps Network Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-9
Cable Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-9
Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-9
v
C Safety and EMC Regulatory Statements
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1
Informations concernant la sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2
Hinweise zur Sicherheit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3
Considerazioni sulla sicurezza . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4
Consideraciones sobre seguridad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5
Safety Information (Japan) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-6
Safety Information (China) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-7
EMC Regulatory Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-8
U.S.A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-8
Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-8
Australia/New Zealand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-8
Japan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-8
Taiwan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-8
European Community . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-9
D Recycle Statements
Waste Electrical and Electronic Equipment (WEEE) Statements . . . . . . D-1
Index
vi
Introducing the Switch
Introducing the Switch
The HP ProCurve Series 6600 Switches are top-of-rack data center switches
that support advanced Layer three switching, and have reversible front-toback airflow, and two hot-swappable power supplies. These switches can be
used to build high-speed switched networks between servers in the data
center.
HP ProCurve 6600-24G Switch (J9263A)
HP ProCurve 6600-24G-4XG Switch (J9264A)
HP ProCurve 6600-24XG Switch (J9265A)
Throughout this manual, these switches will be referred to as the Series 6600
Switches.
1-1
Introducing the Switch
1
Introducing the Switch
Introducing the Switch
The 6600-24G Switch has 20 auto-sensing 10/100/1000Base-T RJ-45 ports, four
dual-personality ports—either auto-sensing 10/100/1000Base-T RJ-45 or miniGBIC (Small Form-Factor Pluggable (SFP)) ports.
The 6600-24G-4XG Switch has the same ports as the Switch 6600-24G plus it
also has 4 SFP+ slots for 10-GbE connectivity. The specification for SFP+
defines the physical and electrical characteristics of this form-factor (size and
shape). The form-factor is identical to SFP, but the SFP+ is a 10-Gigabit
Ethernet transceiver.
The 6600-24XG Switch has 24 SFP+ slots. All slots are 10-GbE.
Table 1-1.
Speed
These products support optional network connectivity with the
following speeds and technologies:
Technology
Cabling
Transceiver form-factor
and connector
SFP (mini-GBIC)
Connector
100-Mbps
1-Gbps
10-Gbps
SFP+
Connector
100-FX
Fiber (multimode)
LC
100-BX
Fiber (single mode)
LC
1000-SX
Fiber (multimode)
LC
1000-LX
Fiber (multimode or
single mode)
LC
1000-LH
Fiber (single mode)
LC
1000-BX
Fiber (single mode)
LC
10-Gig
Direct Attach
Copper (twinaxial)
N/A1
10-Gig SR
Fiber (multimode)
LC
10-Gig LRM
Fiber (multimode)
LC
10-Gig LR
Fiber (single mode)
LC
1 Direct attach cables (DAC) are low-cost 10-GbE connectivity options consisting of a one,
three, or seven meter cable with SFP+ connectors permanently attached to each end.
For supported transceivers see www.procurve.com/faqs. Both ProCurve 10-GbE transceivers and ProCurve Mini-GBICs and SFPs have links to a list of supported products
(first question in the “General Product Information” category).
For technical details of cabling and technologies see Appendix B, “Cabling and Technology Information”.
1-2
Introducing the Switch
This chapter describes the Series 6600 Switches, including:
■
■
■
■
Front and back of the switches
Network ports
LEDs
Switch features
1-3
Introducing the Switch
These switches are designed to be used primarily in data center environments
mounted in equipment racks along with the servers they are connected to.
These switches can directly connect servers to other servers or backbone
LANs to provide dedicated bandwidth to those devices, and can build a
switched network infrastructure by connecting the switch to hubs, other
switches, or routers. In addition, the Series 6600 Switches offer full network
management capabilities.
Introducing the Switch
Front of the Switch
Introducing the Switch
Front of the Switch
Power,
Fault, and
Locator
LEDs
PS, Tmp, Fan, and Test
Status LEDs
Auxiliary port
and LED
Console port
Port LED Mode select
button and indicator LEDs
10/100/1000Base-T
RJ-45 ports
Reset and Clear
buttons
Switch port LEDs
Link and Mode
Dual-personality ports
(1000Base-T or mini-GBIC)
Figure 1-1. ProCurve 6600-24G Switch
Power,
Fault, and
Locator
LEDs
PS, Tmp, Fan, and Test
Status LEDs
Console port
Reset and Clear
buttons
Auxiliary port
and LED
Port LED Mode select
button and indicator LEDs
Switch port LEDs
Link and Mode
10/100/1000Base-T
RJ-45ports
SFP+ 10-GbE ports1
Dual-personality ports
(1000Base-T or mini-GBIC)
1 These SFP+ slots are in the same configuration as the SFP Mini-GBIC slots of ports 21 and 24, label facing down.
Figure 1-2. ProCurve 6600-24G-4XG Switch
1-4
Introducing the Switch
Front of the Switch
Console port
Introducing the Switch
Power,
Fault, and
locator
LEDs
PS, Tmp, Fan, and
Test Status LEDs
Out of Band
Management port,
for future use
Auxiliary port
and LED
Link and Mode LEDs
Port LED Mode select
button and indicator LEDs
SFP+ 10-GbE ports
Reset and Clear
buttons
Figure 1-3. ProCurve 6600-24XG Switch
Network Ports
■
On the 6600-24G and 6600-24G-4XG Switches there are 24 auto-sensing
10/100/1000Base-T ports. All these ports have the “Auto MDIX” feature,
which means you can use either straight-through or crossover twistedpair cables to connect any network devices to the switch.
■
On the 6600-24G and 6600-24G-4XG Switches there are four dual-personality ports. Use either the 10/100/1000Base-T RJ-45 connector, or install a
supported ProCurve mini-GBIC for fiber-optic connections.
Dual-Personality Port Operation. By default, the RJ-45 connectors are
enabled. If a mini-GBIC is installed in a slot, it is enabled and the associated RJ-45 connector is disabled and cannot be used. If the mini-GBIC is
removed, the associated RJ-45 port is automatically re-enabled.
■
On the 6600-24XG Switch there are 24 SFP+ 10-GbE ports. SFP+ ports
only support 10 Gbps operation; 1 Gbps mini-GBICs are not supported in
any SFP+ port.
1-5
Introducing the Switch
Front of the Switch
Introducing the Switch
LEDs
Table 1-2.
Switch LEDs
Switch LEDs
State
Meaning
Power
(green)
On
Blinking1
Off
The power supply is operating properly.
Power supply failure. Blinking simultaneously with Fault LED
No power connection.
Fault
(orange)
Off
The normal state; indicates there are no fault conditions on the switch.
Blinking1
A fault has occurred on the switch, one of the switch ports, module in the rear of
the switch, or the fan. The Status LED for the component with the Fault LED will blink
simultaneously.
On
On briefly after the switch is powered on or reset, at the beginning of switch self
test. If this LED is on for a prolonged time, the switch has encountered a fatal
hardware failure, or has failed its self test. See chapter 4, “Troubleshooting” for
more information.
Locator (blue)
On
Blinking
Off
The Locator LED is used to locate a specific switch in a area full of switches. The
LED can be set to be on solid or blink for a specified number of minutes (1-1440).
The default is 30 minutes. Use the command “chassislocate”.
PS
(green/orange)
On green
Off
The switch is receiving power.
The switch is NOT receiving power.
Blinking
orange1
A fault has occurred on one of the power supplies. The PS Status LED, Fault LED,
and on the back of the switch the failed power supply LED (PS1 or PS2) will all blink
simultaneously.
Tmp
(green/orange)
On green
Switch temperature is normal.
Blinking
orange1
Blinking
orange2
An over temperature condition has been detected. This is a Fault condition
indicating elevated internal temperatures. The Fault LED will blink simultaneously.
This indicates an alert condition indicating critical internal temperatures. The Fault
LED will blink simultaneously.
Fan Status
(green/orange)
On
Blinking
orange1
Blinking
orange2
Normal operation, all fans are ok.
One of the unit’s fans has failed. The switch Fault LED will be blinking simultaneously.
Off
Blinking
orange1
Normal operation, all fans are working properly.
One or more of the unit’s fans has failed. The switch Fault LED, fan status LED on
the front of the switch, and the fan status LED on the back of the switch will be
blinking simultaneously.
Fan LED on the fan
tray (orange)
1-6
One of the unit’s fans has failed and the switch is in an overtemp condition. The
switch Fault LED will be blinking simultaneously.
Introducing the Switch
Front of the Switch
State
Meaning
Test
(green/orange)
Off
The normal operational state; the switch is not undergoing self test.
On green
The switch self test and initialization are in progress after the switch has been
power cycled or reset. The switch is not operational until this LED goes off. The Self
Test LED also comes on briefly when you “hot swap” a mini-GBIC into the switch;
the mini-GBIC is self tested when it is hot swapped.
Blinking
orange1
A component of the switch has failed its self test. The status LED for that component,
for example an RJ-45 port, and the switch Fault LED will blink simultaneously.
Link
Indicates the port LEDs are displaying link information:
• if the port LED is on, the port is enabled and receiving a link indication from the
connected device.
• if the port LED is off, the port has no active network cable connected, or is not
receiving link beat or sufficient light. Otherwise, the port may have been disabled
through the switch console, the web browser interface, or ProCurve Manager.
if the port LED is Blinking1 (orange) simultaneously with the Fault LED, the
corresponding port has failed its self test.
Mode
The operation of the Mode LED is controlled by the LED Mode select button, and
the current setting is indicated by the LED Mode indicator LEDs near the button.
Press the button to step from one view mode to the next. The default view is Activity
(Act).
Act
Indicates the port LEDs are displaying network activity information.
FDx
Indicates port LEDs are lit for ports in Full Duplex Mode. Off indicates ½ duplex.
Spd
Indicates the port LEDs are displaying the connection speed at which each port is
operating:
• if the port LED is off, the port is operating at 10 Mbps.
• if the port LED is Blinking**, the port is operating at 100 Mbps.
• if the port LED is on continuously, the port is operating at 1000 Mbps.
Usr
Indicates the port is displaying customer-specified information.
Blinking
green2
Indicates the process with the USB device is taking place successfully.
On green
The switch has finished processing the USB successfully.
Blinking
orange1
Indicates an error condition. The switch Fault LED will be blinking simultaneously.
There is a USB hardware fault associated with the USB device or the USB
connector on the switch.
Blinking
orange2
Indicates an alert condition. The switch Fault LED should not be blinking
simultaneously. There is an alert error in the USB process that is not caused by a
hardware fault, like a file transfer error.
Off
Indicates that no USB device has been inserted, or that the inserted USB device
cannot be recognized, or that no command file can be found on the inserted USB
device.
Port LEDs
(green/orange –
Link and Mode)
LED Mode View
(green LEDs)
Auxiliary (green/
orange) For more
information see
the Management
and Configuration
Guide for your
switch.
1-7
Introducing the Switch
Switch LEDs
Introducing the Switch
Front of the Switch
Introducing the Switch
Switch LEDs
1
2
State
Meaning
The Blinking behavior is an on/off cycle once every 1.6 seconds, approximately.
The Blinking behavior is an on/off cycle once every 0.8 seconds, approximately.
LED Power Save Mode
The HP ProCurve 6600-24XG Switch (J9265A) has the ability to turn off
defined groups of ports to save power through the use of a CLI command,
“savepower”. This feature provides the capability to explicitly power down
the ports, including the LEDs, for a group of un-used ports associated with a
block number.
Block #
Port Range
1
01-08
2
09-17
3
18-24
This is only a temporary setting. The command is not retained after a power
cycle or reboot. For more information regarding this feature see the Management and Configuration Guide which is on the ProCurve Web site at
www.procurve.com/manuals.
LED Mode Select Button and Indicator LEDs
The operation of the Mode LED is controlled by the LED Mode select button,
and the current setting is indicated by the LED Mode indicator LEDs near the
button. Press the button to step from one view mode to the next.
Port LEDs Link
and Mode
LED Mode select button
and indicator LEDs
Figure 1-4.
1-8
ProCurve 6600-24G and 6600-24G-4XG Switches
Introducing the Switch
Front of the Switch
Introducing the Switch
Port LEDs Link
and Mode
LED Mode select button
and indicator LED
Figure 1-5.
ProCurve 6600-24XG Switch
■
Each port has a Link LED. If it is lit, the port has a link. If the Link LED is
Blinking, the port has failed its self test. The Fault and Self Test LEDs will
be Blinking simultaneously.
■
If the Activity (Act) indicator LED is lit, each port LED displays activity
information for the associated port—it flickers as network traffic is
received and transmitted through the port.
■
If the Full Duplex (FDx) indicator LED is lit, the port LEDs light for those
ports that are operating in full duplex.
■
If the Speed (Spd) indicator LED is lit, the port LEDs behave as follows
to indicate the connection speed for the port:
■
•
Off = 10 Mbps
•
Blinking = 100 Mbps (the Blinking behavior is a repeated on/off cycle
once every 0.8 sec.)
•
On = 1000 Mbps
The Usr Mode LED indicates the port is displaying customer-specified
information.
Reset Button
This button is for:
■
Resetting the switch - When the switch is powered on. This action clears
any temporary error conditions that may have occurred and executes the
switch self test.
■
Restoring Factory Default Configuration - When pressed with the
Clear button in a specific pattern, any configuration changes you may have
made through the switch console, the web browser interface, and SNMP
management are removed, and the factory default configuration is
restored to the switch. For the specific method to restore the factory
default configuration, see “Restoring the Factory Default Configuration”
on page 11, in the Troubleshooting chapter of this manual.
1-9
Introducing the Switch
Front of the Switch
Introducing the Switch
Clear Button
This button is used for:
■
Deleting Passwords - When pressed by itself for at least one second, the
button deletes any switch console access passwords that you may have
configured. Use this feature if you have misplaced the password and need
console access. This button is provided as a convenience, however if you
are concerned with the security of the switch configuration and operation,
you should make sure the switch is installed in a secure location. This
button can be disabled by a CLI command.
■
Restoring Factory Default Configuration - See Reset Button above.
Console Port
This port is used to connect a console to the switch either by using the RJ-45
to DB9 cable or the DB9 to DB9 serial cable supplied with the switch. The
Series 6600-24G and 6600-24G-4XG Switches use the DB9 to DB9 serial cable
and the 6600-24XG Switch uses the RJ-45 to DB cable. This connection is
described under “Connect a Console to the Switch” in chapter 2, “Installing
the Switch.” The console can be a PC or workstation running a VT-100 terminal
emulator, or a VT-100 terminal.
1-10
Introducing the Switch
Back of the Switch
Introducing the Switch
Back of the Switch
Power supply and
Locator LEDs
Power supply
AC power connector
Fan tray assembly
Extra power slot
Figure 1-6. HP ProCurve Series 6600 Switches. The backs of all these switches
are the same.
Power Connector
The Series 6600 Switches do not have a power switch; they are powered on
when connected to an active AC power source. These switches automatically
adjust to any voltage between 100--127 and 200--240 volts and either 50 or 60
Hz. There are no voltage range settings required.
Switch Features
The features of the Series 6600 Switches include:
■
24 auto-sensing 10/100/1000Base-T RJ-45 ports with Auto-MDIX or 24
SFP+ 10-GbE ports. The 6600-24G-4XG has only 4 SFP+ 10-GbE ports.
■
Four dual-personality ports—either the auto sensing 10/100/1000Base-T
RJ-45 or the mini-GBIC can be used for each port. The 6600-24XG does
not have these dual-personality ports.
■
An auxiliary (USB) port for processing a USB command file.
■
Plug-and-play networking—all ports are enabled—just connect the
network cables to active network devices and your switched network is
operational.
1-11
Introducing the Switch
Introducing the Switch
Switch Features
1-12
■
The 6600-24G and the 6600-24G-4XG supports IEEE 802.3ab Auto MDIX
on all 10/100/1000 twisted-pair ports, meaning that all connections can
be made using straight-through twisted-pair cables. Cross-over
cables are not required, although they will also work. The pin operation
of each port is automatically adjusted for the attached device: if the switch
detects that another switch or hub is connected to the port, it configures
the port as MDI; if the switch detects that an end-node device is connected
to the port, it configures the port as MDI-X.
■
Automatic learning of the network addresses in each switch’s 8000address forwarding table, (with configurable address aging value).
■
Automatically negotiated full-duplex operation for the 10/100/1000 RJ-45
ports when connected to other auto-negotiating devices—the mini-GBIC
ports always operate at full duplex.
■
Easy management of the switch through several available interfaces:
•
console interface—a full featured, easy to use, VT-100 terminal
interface that is especially good for out-of-band switch management
or for Telnet access to the switch.
•
web browser interface—an easy to use built-in graphical interface
that can be accessed from common web browsers.
•
ProCurve Manager—an SNMP-based, graphical network management tool that you can use to manage your entire network. This
product is included with your new switch.
■
Support for the Spanning Tree Protocol to eliminate network loops
■
Support for up to 2048 IEEE 802.1Q-compliant VLANs so you can divide
the attached end nodes into logical groupings that fit your business needs.
■
Support for many advanced features to enhance network performance—
for a description, see the Management and Configuration Guide, which
is on the ProCurve Web site www.procurve.com/manuals.
■
Download of new switch software for product enhancements or bug fixes.
Installing the Switch
Included Parts
2
Installing the Switch
Caution
If the switch is to be shipped in a rack, be sure to use only an HP 10K rack.
Mount the switch using rail mounting kit, (5070-6532). The switch warranty
may be voided.
Included Parts
The Series 6600 Switches have the following components shipped with them:
■
HP ProCurve Switch Quick Setup sheet
■
HP ProCurve Switches General Safety and Regulatory Information
booklet
■
Series 6600 Switch Safety and Regulatory Information sheet
■
Read Me First
■
Customer Support/Warranty booklet
■
Console cable
■
Accessory kits
5070-6315 used with the
J9263A and J9264A
5070-6316 used with the
J9265A
two mounting brackets
two mounting brackets
eight 8-mm M4 screws to attach the
mounting brackets to the switch
eight 8-mm M4 screws to attach the
mounting brackets to the switch
four 5/8-inch number 12-24 screws to
attach the switch to a rack
four 5/8-inch number 12-24 screws to
attach the switch to a rack
2-1
Installing the Switch
The HP ProCurve Series 6600 Switches come with an accessory kit that
includes the brackets for mounting the switch in a standard 19-inch telco rack,
or in an equipment cabinet. The brackets are designed to allow mounting the
switch in a variety of locations and orientations. For other mounting options
contact your local ProCurve authorized network reseller or ProCurve representative. This chapter shows how to install the switch.
Installing the Switch
Included Parts
Installing the Switch
■
Power cord, one of the following:
Australia/New Zealand
China
Continental Europe
Denmark
Japan
Switzerland
United Kingdom/Hong Kong/Singapore
United States/Canada/Mexico
South Africa
India
Argentina
Thailand
Brazil
Chile
Taiwan
Israel
Japan Power
Cord Warning
2-2
8120-6810
8120-8707
8120-6811
8120-6814
8120-4753
8120-6815
8120-6809
8120-6812
8120-6813
8120-6813
8120-6869
8121-0668
8121-1069
8120-6980
8121-0974
8121-1035
Installing the Switch
Included Parts
Installation Precautions:
Follow these precautions when installing the Series 6600 Switches.
WARNING
The rack or cabinet should be adequately secured to prevent it
from becoming unstable and/or falling over.
■
Devices installed in a rack or cabinet should be mounted as low as
possible, with the heaviest devices at the bottom and progressively
lighter devices installed above.
■
Do not wall mount the Series 6600 Switches.
■
The Series 6600 Switches should be mounted with the optional Rail
Mounting Kit (5070-6532) in an HP 10000 (HP 10K) rack or any 4 post
racking solution.
■
Ensure the power source circuits are properly grounded, then use the
power cord supplied with the switch to connect it to the power source.
■
If your installation requires a different power cord than the one supplied
with the switch and power supply, be sure the cord is adequately sized for
the switch’s current requirements. In addition, be sure to use a power cord
displaying the mark of the safety agency that defines the regulations for
power cords in your country. The mark is your assurance that the power
cord can be used safely with the switch and power supply.
■
When installing the switch, the AC outlet should be near the switch and
should be easily accessible in case the switch must be powered off.
■
Ensure the switch does not overload the power circuits, wiring, and overcurrent protection. To determine the possibility of overloading the supply
circuits, add together the ampere ratings of all devices installed on the
same circuit as the switch and compare the total with the rating limit for
the circuit. The maximum ampere ratings are usually printed on the
devices near the AC power connectors.
■
Do not install the switch in an environment where the operating ambient
temperature might exceed 40°C (104°F).
■
Ensure the air flow around the front and back of the switch is not
restricted. Leave at least 7.6 cm (3 inches) for cooling. See page 2-4 for
the air flow direction.
2-3
Installing the Switch
Cautions
■
Installing the Switch
Installing the Switch
Installation Procedures
Figure 2-1. Default air flow direction of the Series 6600 Switches is from power to
ports.
The direction of air flow can be reversed from the default direction shown in
figure 2-1 by reversing the direction of the fans. See step 3 below, Reversing
the air flow.
Installation Procedures
Summary
2-4
1.
Prepare the installation site (page 2-5). Ensure the physical environment is properly prepared, including having the correct network cabling
ready to connect to the switch and having an appropriate location for the
switch. See page 2-3 for some installation precautions.
2.
Verify the switch passes self test (page 2-5). Plug the switch into a
power source and observe that the LEDs on the switch’s front panel
indicate correct switch operation. When self test is complete, unplug the
switch.
3.
(Optional) Reversing the air flow (page 2-8) The direction of air flow
can be reversed from the default direction by reversing the fans.
4.
Mount the switch (page 2-10). The Switch can be mounted in a 19-inch
telco rack, or in an equipment cabinet.
Installing the Switch
Installation Procedures
Connect power to the switch (page 2-14). Once the switch is mounted,
plug it into the nearby main power source.
6.
(Optional) Install or remove mini-GBICs or SFPs (page 2-15). The
switch has four slots for installing mini-GBICs. Depending on where you
will mount the switch, it may be easier to install the mini-GBICs first. MiniGBICs can be installed or removed while the switch is powered on.
7.
Connect the network cables (page 2-18). Using the appropriate
network cables, connect the network devices to the switch ports.
8.
(Optional) Connect a console to the switch (page 2-19). You may
wish to modify the switch’s configuration, for example, to configure an IP
address so it can be managed using a web browser, from an SNMP network
management station, or through a Telnet session. Configuration changes
can be made easily by using the included console cable to connect a PC
to the switch’s console port.
At this point, the switch is fully installed. See the rest of this chapter if you
need more detailed information on any of these installation steps.
1. Prepare the Installation Site
Cabling Infrastructure - Ensure the cabling infrastructure meets the
necessary network requirements. See Appendix B “Cabling and Technology
Information” for more information.
■
Installation Location - Before installing the switch, plan its location and
orientation relative to other devices and equipment:
•
In the front of the switch, leave at least 7.6 cm (3 inches) of space for
the twisted-pair, fiber-optic cabling, and cooling. See Figure 2-1 for
the air flow direction.
•
In the back of the switch, leave at least 3.8 cm (1 1/2 inches) of space
for the power cord and cooling.
2. Verify the Switch Passes Self Test
Before mounting the switch in its network location, you should first verify it
is working properly by plugging it into a power source and verifying it passes
self test.
2-5
Installing the Switch
5.
Installing the Switch
Installation Procedures
Installing the Switch
1.
Connect the power cord supplied with the switch to the power connector
on the back of the power supply, and then into a properly grounded
electrical outlet.
Figure 2-2. Connecting the power cord.
Note
The Series 6600 Switches do not have a power switch. They are powered on
when the power cord is connected to the power supply and to a power source.
For safety, the power outlet should be located near the switch installation.
The power supply cannot be removed when the power cord is connected.
The switch automatically adjusts to any voltage between 100-127 and 200-240
volts and either 50 or 60 Hz. No voltage range settings are required.
If your installation requires a different power cord than the one supplied with
the switch, be sure to use a power cord displaying the mark of the safety
agency that defines the regulations for power cords in your country. The mark
is your assurance that the power cord can be used safely with the switch.
2.
2-6
Check the LEDs on the switch as described below. When the switch is
powered on, it performs its diagnostic self test. Self test takes approximately 50 seconds to complete.
Installing the Switch
Installation Procedures
Switch port LEDs
Power and
Fault LEDs
Test LED
Figure 2-3. Checking the LEDs on the 6600-24G and 6600-24G-4XG
Installing the Switch
Switch port LEDs
Power and
Fault LEDs
Test LED
Figure 2-4. Checking the LEDs on the 6600-24XG
LED Behavior:
During the self test:
•
Initially, all the status, LED Mode and port LEDs are on for most of
the duration of the test.
•
Most of the LEDs go off and then may come on again during phases
of the self test. For the duration of the self test, the Test LED stays on.
When the self test completes successfully:
•
The Power and Fan Status LEDs remain on.
•
The Fault and Test LEDs go off.
•
The port LEDs on the front of the switch go into their normal
operational mode:
2-7
Installing the Switch
Installation Procedures
–
–
If the ports are connected to active network devices, the LEDs
behave according to the LED Mode selected. In the default view
mode (Link), the LEDs should be on.
If the ports are not connected to active network devices, the LEDs
will stay off.
If the LED display is different than what is described above, especially if
the Fault and Test LEDs stay on for more than 60 seconds or they start
blinking, the self test has not completed correctly. Refer to chapter 4,
“Troubleshooting” for diagnostic help.
3. (Optional) Reversing the air flow
Installing the Switch
If desired, the air flow direction can be reversed by following these steps.
This is not a hot swap operation. Make sure this is done during planned
down time.
1.
Remove the fan tray assembly
a.
Unscrew the retaining screws
b.
Holding the two retaining screws, pull the fan tray assembly straight
out.
Retaining
Screw
2.
2-8
Fan tray
assembly
Using a T10 screwdriver, remove the four retaining screws.
Installing the Switch
Installation Procedures
3.
Lift the fan assembly from the fan tray high enough to turn it over.
Retaining
Screw
Rotate the fan assembly 180 degrees and replace the fan assembly into
the fan tray, sheet metal side up.
Rotated
position
5.
Take care to align the sensing pin between the two sensors and replace
the 4 retaining screws.
Sensors
Sensing pin
6.
Replace the fan tray assembly into the switch.
7.
Tighten the retaining screws.
Retaining
Screw
2-9
Installing the Switch
4.
Rotating fan
tray
Installing the Switch
Installation Procedures
4. Mount the Switch
After the switch passes self test, it is ready to be mounted in a stable location.
Rack or Cabinet Mounting
Installing the Switch
The Series 6600 Switches are designed to be mounted in any EIA-standard 19inch telco rack or communication equipment cabinet using the balanced or
center mounting orientation, see figure 2-5. Flush mounting in a two post rack
is not supported. Or with the optional Rail Mounting Kit (5070-6532) in an HP
10000 (HP 10K) rack or any 4 post racking solution, see figures 2-6 through
2-10. Secure the rack in accordance with the manufacture’s safety guidelines.
WARNING
For safe operation, please read the mounting precautions on page 2-3,
before mounting a switch.
Equipment
Cabinet
Note
The 12-24 screws supplied with the switch are the correct threading for
standard EIA/TIA open 19-inch racks. If you are installing the switch in an
equipment cabinet such as a server cabinet, use the clips and screws that came
with the cabinet in place of the 12-24 screws that are supplied with the switch.
Complete step 1, and plan which four holes you will be using in the cabinet
and install all four clips. Then proceed to step 2.
Note
2-10
The mounting brackets have multiple mounting holes and can be rotated
allowing for a wide variety of mounting options. These include mounting it in
a more balanced position (which is the ProCurve recommended option for the
Series 6600 Switches when mounting in a two post rack) as shown in Figure
2-5, or mounting the switch so its front face is flush with the face of the rack,
as shown in Figure 2-6. This installation is used for mounting in a four post
HP 10K rack, see Figure 2-9.
Installing the Switch
Installation Procedures
1.
Use a #1 Phillips (cross-head) screwdriver and attach the mounting
brackets to the switch with the included 8-mm M4 screws. Remember to
use the correct accessory kit for your switch, see page 2-1.
8 mm
M4 screws
Figure 2-6. Example attaching mounting brackets
2-11
Installing the Switch
Figure 2-5. Mounting in a two post rack using the balanced option.
Installing the Switch
Installation Procedures
Installing the Switch
2.
Attach the holding brackets. Ensure the holes of the brackets and the
screws are aligned to the bottom of the switch.
Figure 2-7. Installing the rail mounting holding brackets
3.
Install the rails.
Figure 2-8. Mounting rails in a four-post HP 10K rack
2-12
Installing the Switch
Installation Procedures
4.
Slide the switch into the rails
5.
Hold the switch with attached brackets up to the rack and move it
vertically until rack holes line up with the bracket holes, then insert and
tighten the four number 12-24 screws holding the brackets to the rack.
Figure 2-10. Mounting in a rack
Caution
Make sure the air flow is not restricted in the front or back of the switch. See
Figure 2-1 on page 2-4 for the air flow direction.
2-13
Installing the Switch
Figure 2-9. Sliding the switch into the rails
Installing the Switch
Installation Procedures
5. Connect the Switch to a Power Source
1.
Plug the included power cord into the switch’s power connector and into
a nearby AC power source.
2.
Re-check the LEDs during self test. See “LED Behavior” on page 2-7.
Securing the power cord
1.Connect the power cord to the power supply.
Installing the Switch
2.Make a small loop in the power cord, approximately 3 to 4 inches
and insert the velcro strap through the loop and through the handle
on power supply.
3.Insert the end of the velcro strap through the slot in the other end
of the velcro strap.
4.Tighten the velcro strap around the loop in the power cord.
5.Wrap the excess velcro strap around the power cord loop and
through the power supply handle a couple of times and secure the
velcro strap to itself.
1.
2-14
2.
Installing the Switch
Installation Procedures
3.
4.
Installing the Switch
5.
6. (Optional) Install or Remove mini-GBICs or SFPs
You can install or remove a mini-GBIC from a mini-GBIC slot without having
to power off the switch. Use only ProCurve transceiver accessories.
Notes
■
The mini-GBIC slots are shared with the four 10/100/1000Base-T RJ-45
ports. If a mini-GBIC is installed in a slot, the associated RJ-45 port is
disabled and cannot be used.
■
The mini-GBICs operate only at full duplex. Half duplex operation is not
supported.
■
Inserting a 10-GbE transceiver (SFP+) into a 1 gigabit (mini-GBIC) slot,
will generate an event log message, “Transceiver type not supported by
this port”, and the transceiver will not function. The reverse is true also,
inserting a 1 gigabit (mini-GBIC) transceiver into a 10-GbE slot will
generate an event log message and the transceiver will not function.
■
Ensure the network cable is NOT connected when you install or remove
a mini-GBIC unless you are using a Direct Attach Cable (DAC).
2-15
Installing the Switch
Installation Procedures
Installing the Switch
Note
Direct attach cables (DAC) are lowcost 10-GbE connectivity options
consisting of a one, three, or seven
meter cable with SFP+ connectors
permanently attached to each end.
Figure 2-11. One meter DAC
Caution
Use only supported genuine HP ProCurve transceiver accessories with your
switch. Non-ProCurve transceiver accessories are not supported, and their
use may result in product malfunction. Should you require additional
ProCurve transceiver accessories, contact your ProCurve Networking Sales
and Service Office or authorized dealer.
Installing the Mini-GBICs or SFP+ Transceivers:
Hold the mini-GBIC by its sides and gently insert it into any of the mini-GBIC
slots on the switch until the mini-GBIC clicks into place.
10-GbE
transceiver
Figure 2-12. Installing a Mini-GBIC or SFP
2-16
Installing the Switch
Installation Procedures
WARNING
The ProCurve mini-GBICs are Class 1 laser devices. Avoid direct eye
exposure to the beam coming from the transmit port.
SFP and SFP+ transceivers Plug-in, Fault and Alert behaviors.
Working SFP Transceiver plugged into SFP slot 21S, 22S, 23S or 24S:
■
When the switch recognizes the transceiver, the Mode LED turns on solid
for 2 seconds and then goes to normal operation.
•
After inserting a mini-GBIC, do not remove it until the Mode LED has
turned off.
Working SFP+ Transceiver plugged into SFP+ slot 25, 26, 27 & 28:
When the switch recognizes the transceiver, the Mode LED turns on solid
for 2 seconds and then goes to normal operation.
•
After inserting an SFP+ transceiver, do not remove it until the Mode
LED has turned off.
For a faulty or non-ProCurve Transceiver:
■
The switch Fault LED and port Link LED for the affected port would be
slow flashed for situations that cannot be fixed by the customer.
For working but unsupported transceiver including:
1.
SFP transceiver into SFP+ slot 25, 26, 27 or 28
2.
SFP+ transceiver into SFP slot 21S, 22S, 23S or 24S:
■
Orange fast flash on the port's Link LED for the affected port, plus
appropriate log messages. Examples include transceivers are not
supported by the current software, or are the wrong revision, or are the
wrong type.
Removing the mini-GBICs:
Note
You should disconnect the network cable from the mini-GBIC before removing
it from the switch.
Depending on when you purchased your ProCurve mini-GBIC, it may have
either of three different release mechanisms:
■
a plastic tab on the bottom of the mini-GBIC
■
a plastic collar around the mini-GBIC
■
a wire bail
2-17
Installing the Switch
■
Installing the Switch
Installation Procedures
To remove the mini-GBICs that have the plastic tab or plastic collar, push the
tab or collar toward the switch until you see the mini-GBIC release from the
switch (you can see it move outward slightly), and then pull it from the slot.
To remove the mini-GBICs that have the wire bail, lower the bail until it is
approximately horizontal, and then using the bail, pull the mini-GBIC from the
slot.
7. Connect the Network Cables
Installing the Switch
Connect the network cables, described under “Cabling Infrastructure” (page
2-5), from the network devices or your patch panels to the fixed RJ-45 ports
on the switch or to any mini-GBICs you have installed in the switch.
Using the RJ-45 Connectors
To connect:
Push the RJ-45 plug into the RJ-45 jack
until the tab on the plug clicks into
place. When power is on for the switch
and for the connected device, the Link
LED for the port should light to confirm
a powered-on device (for example, an
end node) is at the other end of the
cable.
If the Link LED does not go on when the
network cable is connected to the port,
see “Diagnosing with the LEDs” on
page 5-4, in chapter 5, “Troubleshooting”.
To disconnect:
Press the small tab on the plug and pull
the plug out of the jack.
RJ-45
connector
Unshielded twisted-pair cable:
• Category 3, 4, or 5 for 10 Mbps ports
• Category 5 or better for 100 Mbps ports
• Category 5e or better for 1000 Mbps ports
Maximum distance: 100 meters
Figure 2-13. Connecting RJ-45s
Connecting Cables to mini-GBICs
Note
Each of the four mini-GBIC slots is shared with the associated 10/100/
1000Base-T RJ-45 port. If a mini-GBIC is installed in a slot, the associated RJ45 port is disabled.
If you have any mini-GBICs installed in the switch, the type of network
connections you will need to use depends on the type of mini-GBICs you have
installed. See Appendix B, “Cabling and Technology Information”, for the miniGBIC cabling information.
2-18
Installing the Switch
Installation Procedures
For mini-GBICs ports, and in general
for all the switch ports, when a network
cable from an active network device is
connected to the port, the port LED for
that port should go on. If the port LED
does not go on when the network cable
is connected to the port, see “Diagnosing with the LEDs” on page 5-4 in
chapter 5, “Troubleshooting”.
8. (Optional) Connect a
Console to the Switch
Figure 2-14. Connecting a Fiber cable
connector
■
■
■
■
■
monitor switch and port status and observe network activity statistics
modify the switch’s configuration to optimize switch performance,
enhance network traffic control, and improve network security
read the event log and access diagnostic tools to help in troubleshooting
download new software to the switch
add passwords to control access to the switch from the console, web
browser interface, and network management stations
The console can be accessed through these methods:
■
Out-of-band: The switch comes with a cable for connecting a PC or VT100 terminal, to be used as a console, directly to the switch. You can use
the console port only for out-of-band management. It cannot be used for
a Telnet connection.
■
In-Band: Manage the switch using Telnet from a PC or UNIX workstation
on the network, and a VT-100 terminal emulator. This method requires that
you first configure the switch with an IP address and subnet mask by using
either out-of-band console access or through DHCP/Bootp. For more
information on IP addressing and on starting a Telnet session, see
chapter 3, “Getting Started With Switch Configuration”, and the Management and Configuration Guide, which is on the ProCurve Web site at
www.procurve.com/manuals.
The Switch can simultaneously support one out-of-band console session
through the Console Port and one in-band Telnet console session.
2-19
Installing the Switch
The switch has a full-featured, easy to
use console interface for performing
switch management tasks including the following:
Installing the Switch
Installation Procedures
Terminal Configuration
To connect a console to the switch, configure the PC terminal emulator as a
DEC VT-100 (ANSI) terminal or use a VT-100 terminal, and configure either
one to operate with these settings:
■
any baud rate from 1200 to 115200 (the switch senses the speed)
■
8 data bits, 1 stop bit, no parity, and flow control set to Xon/Xoff
■
for the Windows Terminal program, also disable (uncheck) the “Use
Function, Arrow, and Ctrl Keys for Windows” option
■
for the Hilgraeve HyperTerminal program, select the “Terminal keys”
option for the “Function, Arrow, and Ctrl Keys act as” parameter
Installing the Switch
If you want to operate the console using a different configuration, make sure
you change the settings on both the terminal and on the switch so they are
compatible. Change the switch settings first, save your changes, then change
the terminal settings, then reboot the switch and reestablish the console
session.
Direct Console Access
To connect a console to the
switch, follow these steps:
1.
Connect the PC or terminal
to the switch’s Console Port
using the console cable
included with the Switch. (If
your PC or terminal has a 25pin serial connector, first
attach a 9-pin to 25-pin
straight-through adapter at
one end of the console
cable.)
Console port
Console cable supplied
with the switch
PC running a terminal
emulator program, or
a VT-100 terminal
Figure 2-15. Connecting the console cable
Note
2-20
The ProCurve Switch 6600-24XG (J9265A) is shipped with an RJ-45 to 9-pin
console cable.
Installing the Switch
Installation Procedures
2.
3.
Turn on the terminal or
PC’s power and, if using a
PC, start the PC terminal
program.
Console cable supplied
with the switch
PC running a terminal
emulator program, or
a VT-100 terminal
Figure 2-16. Connecting the console cable
ProCurve Switch 6600-24G#
If you want to continue with console management of the switch at this time,
see chapter 3, “Getting Started With Switch Configuration” for some basic
configuration steps. For more detailed information, refer to the Management
and Configuration Guide, which is on the ProCurve Web site at
www.procurve.com/manuals.
Console Cable Pinouts
The console cable has an RJ-45 male connector on one end and a DB-9 female
connector on the other end. Table 2-16 describes the mapping of the RJ-45 to
DB-9 pins.
12345678
5
4
9
3
8
2
7
1
6
12345678
Figure 2-17. RJ-45 to DB-9 pinouts
2-21
Installing the Switch
Press [Enter] two or three
times and you will see the
copyright page and the
message “Press any key to
continue”. Press a key, and
you will then see the
switch console command
(CLI) prompt, for
example:
Console port
Installing the Switch
Sample Network Topology
Table 2-18. Mapping of RJ-45 to DB-9
Installing the Switch
RJ-45 (Signal reference from
Chassis
DB-9 (Signal reference from PC)
RTS
1
8
CTS
TX_Debug
2
6
DSR
TXD
3
2
RXD
GND
4
5
GND
DCD
5
1
DCD
RXD
6
3
TXD
RX_Debug
7
4
DTR
CTS
8
7
RTS
9
RI
Sample Network Topology
An industry standard building block approach requires that applications can
be adapted to a common server environment. Virtualization of these resources
allows for improved scaling, flexibility, and efficient use of resources, while
delivering seamless interoperability.
2-22
Installing the Switch
Sample Network Topology
In such a model, server/access layer network infrastructure can be completely
standardized and continuously deployed without regard to application
requirements.
Gigabit fiber cable
Installing the Switch
ProCurve Switch 6600
Gigabit fiber cable
ProCurve Switch 6600
Servers
Servers
Servers
Servers
Figure 2-19. Example topology
2-23
Getting Started With Switch Configuration
Recommended Minimal Configuration
3
Getting Started With Switch Configuration
This chapter is a guide for using the console Switch Setup screen to quickly
assign an IP (Internet Protocol) address and subnet mask to the switch, set a
Manager password, and, optionally, configure other basic features.
For more information on using the switch console and the other switch
management interfaces: the web browser interface and the SNMP
management tool, ProCurve Manager, please see the Management and
Configuration Guide, which is on the ProCurve Web site at
www.procurve.com/manuals.
Recommended Minimal Configuration
Many other features can be configured through the switch’s console interface,
to optimize the switch’s performance, to enhance your control of the network
traffic, and to improve network security. Once an IP address has been
configured on the switch, these features can be accessed more conveniently
through a remote Telnet session, through the switch’s web browser interface,
and from an SNMP network management station running a network
management program, such as ProCurve Manager. For a listing of switch
features available with and without an IP address, refer to “How IP Addressing
Affects Switch Operation” in the Management and Configuration Guide,
which is on the ProCurve Web site at www.procurve.com/manuals.
For more information on IP addressing, refer to “IP Configuration” in the
Management and Configuration Guide.
3-1
Getting Started With Switch
Configuration
In the factory default configuration, the switch has no IP (Internet Protocol)
address and subnet mask, and no passwords. In this state, it can be managed
only through a direct console connection. To manage the switch through inband (networked) access, you should configure the switch with an IP address
and subnet mask compatible with your network. Also, you should configure
a Manager password to control access privileges from the console and web
browser interface. Other parameters in the Switch Setup screen can be left at
their default settings or you can configure them with values you enter.
Getting Started With Switch Configuration
Using the Console Setup Screen
Note
By default, the switch is configured to acquire an IP address configuration
from a DHCP or Bootp server. To use DHCP/Bootp instead of the manual
method described in this chapter, see “DHCP/Bootp Operation” in the
Management and Configuration Guide, which is on the ProCurve Web site
at www.procurve.com/manuals.
Using the Console Setup Screen
The quickest and easiest way to minimally configure the switch for
management and password protection in your network is to use a direct
console connection to the switch, start a console session, and access the
Switch Setup screen.
1.
Using the method described in the preceding section, connect a terminal
device to the switch and display the switch console command (CLI)
prompt (the default display).
The CLI prompt appears displaying the switch model number:
ProCurve 6600-24G Switch#
Getting Started With Switch
Configuration
2.
At the prompt, enter the setup command to display the Switch Setup
screen. The following illustration shows the Setup screen with the default
settings.
58
6600-24G
Pr oCurve Switch
3.
3-2
6600-24G
Use the [Tab] key to select the Manager Password field and enter a manager
password of up to 16 characters.
Getting Started With Switch Configuration
Using the Console Setup Screen
4.
[Tab] to the IP Config (DHCP/Bootp) field and use the Space bar to select the
Manual option.
5.
[Tab] to the IP Address field and enter the IP address that is compatible with
your network.
6.
[Tab] to the Subnet Mask field and enter the subnet mask used for your
network.
7.
Press [Enter], then [S] (for Save).
Here is some information on the fields in the Setup screen. For more
information on these fields, see the Management and Configuration Guide,
which is on the ProCurve Web site at www.procurve.com/manuals:
Default
System Name
blank
Optional; up to 25 characters, including spaces
System Contact
blank
Optional; up to 48 characters, including spaces
Manager Password
blank
Recommended; up to 16 characters (no blank spaces)
Logon Default
CLI
The default setting selects the command line interface for console access.
The alternative is the menu interface.
Time Zone
0 (none)
Optional; 1440 to -1440. The number of minutes your location is to the West (-)
or East (+) of GMT.
Community Name
public
Default setting recommended.
Spanning Tree Enabled
No
Default setting recommended unless STP is already running on your network
or the switch will be used in complex network topologies.
Default Gateway
blank
Optional; Enter the IP address of the next-hop gateway node if network traffic
needs to be able to reach off-subnet destinations.
Time Sync Method
None
Optional; The protocol the switch uses to acquire a time signal. The options
are SNTP and TimeP.
TimeP Mode
Disabled
Optional; The method the switch uses to acquire the TimeP server address.
IP Config (DHCP/Bootp)
DHCP/Bootp
Set to Manual unless a DHCP/Bootp server is used on your network to
configure IP addressing.
IP Address
xxx.xxx.xxx.xxx Recommended; If you set IP Config to Manual, then enter an IP address
compatible with your network.
Note: The IP address and subnet mask assigned for the switch must be compatible with the IP addressing used in your
network. For more information on IP addressing, see the Management and Configuration Guide, which is on the ProCurve
Web site at www.procurve.com/manuals.
Subnet Mask
xxx.xxx.xxx.xxx Recommended; If you entered an IP address, then enter a subnet mask
compatible with your network.
3-3
Getting Started With Switch
Configuration
Parameter
Getting Started With Switch Configuration
Where to Go From Here
Where to Go From Here
The above procedure configures your switch with a Manager password, IP
address, and subnet mask. As a result, with the proper network connections,
you can now manage the switch from a PC equipped with Telnet, a web
browser interface, or from an SNMP-based network management station
using a tool such as ProCurve Manager.
Some basic information on managing your switch is included in the next
section. For more information on the console, web browser, and SNMP
management interfaces and all the features that can be configured on the
switch, see the Management and Configuration Guide, which is on the
ProCurve Web site at www.procurve.com/manuals.
To Recover from a Lost Manager Password
Getting Started With Switch
Configuration
If you cannot start a console session at the manager level because of a lost
Manager password, you can clear all passwords and user names by getting
physical access to the switch and pressing and holding the Clear button for a
full second.
3-4
Getting Started With Switch Configuration
Using the IP Address for Remote Switch Management
Using the IP Address for Remote Switch
Management
The switch’s IP address can be used to manage the switch from any PC that
is on the same subnet as the switch. Either a Telnet session or a standard web
browser can be used to manage the switch.
Starting a Telnet Session
To access the switch through a Telnet session, follow these steps:
1.
Make sure the switch is configured with an IP address and that the switch
is reachable from the PC that is running the Telnet session (for example,
by using a Ping command to the switch’s IP address).
2.
Start the Telnet program on a PC that is on the same subnet as the switch
and connect to the switch’s IP address.
3.
You will see the copyright page and the message “Press any key to
continue”. Press a key, and you will then see the switch console command
(CLI) prompt, for example:
Enter help or ? to see a list of commands that can be executed at the
prompt. Entering any command followed by help provides more detailed
context help information about the command. Entering any command
followed by ? displays a list of options that are available at that point in
the command entry.
Starting a Web Browser Session
Your Switch can be managed through a graphical interface that you can access
from any PC or workstation on the network by running your web browser and
typing in the switch’s IP address as the URL. No additional software
installation is required to make this interface available; it is included in the
switch’s onboard software.
The operating systems, web browsers, and Java support required to manage
the switch through the browser interface are listed in the following table:
3-5
Getting Started With Switch
Configuration
ProCurve 6600-24G-4XG Switch#
Getting Started With Switch Configuration
Using the IP Address for Remote Switch Management
Operating System
Internet Explorer
Java Version
Windows 2000 SP4
5.5 SP2, 6.0 SP1
1.3.1_12 and 1.4.2_05
Windows XP SP1a
6.0 SP1
1.3.1_12 and 1.4.2_05
Windows Server 2003
6.0 SP1
1.3.1_12 and 1.4.2_05
Getting Started With Switch
Configuration
The following illustration shows a typical web browser interface screen.
For more information on using the web browser interface, see the
Management and Configuration Guide, which is on the ProCurve Web site
at www.procurve.com/manuals.
An extensive help system is also available for the web browser interface. To
access the help system though, the subnet on which the switch is installed
must have access to the internet, or ProCurve Manager needs to be installed
on a network management station that is on the subnet.
3-6
Replacing Components
Replacing the fan tray assembly
4
Replacing Components
This chapter shows you how to remove and install the following components:
Hot Swapping
Caution
■
Fan tray (see page 4-1)
■
Battery (see page 4-3)
■
Power Supplies (see page 4-5)
The battery cannot be hot swapped. The switch must be powered off to replace
the battery because the top must be removed.
The HP ProCurve Series 6600 Switch and its components are sensitive to static
discharge. Use an antistatic wrist strap and observe all static precautions
when replacing components.
Replacing the fan tray assembly
When a fan fails the Fan Status LED on the switch chassis will blink
simultaneously with the switch Fault LED. In this case, the entire fan tray
assembly needs to be replaced. Individual fans cannot be replaced.
WARNING
To avoid contact with spinning fans, if you are hot swapping out the
fan tray assembly, pull the assembly out one-inch and allow the fans
to stop rotating (approximately 5 seconds) before pulling it all the
way out.
4-1
Replacing Components
The fan tray assembly is hot swappable. It can be removed and replaced
without removing power from the switch. However, install the new fan tray
assembly immediately (within two minutes) after removing the old fan tray
assembly to avoid overheating and switch shutdown.
Replacing Components
Replacing the fan tray assembly
Caution
If the fan assembly is replaced with the switch powered on, you will have
approximately three minutes before the switch overheats.
To replace a fan tray assembly:
1.
Unscrew the retaining screws.
Retaining
screw
Figure 4-1. Fan tray assembly retaining screws
2.
Holding the two retaining screws, pull the fan tray assembly straight out.
Fan tray
assembly
Figure 4-2. Removing the fan tray assembly
Replacing Components
3.
Note
4-2
Remove the new fan tray assembly from it’s packaging.
Before installing the new fan tray assembly be sure the air flow direction is
the same as the fan tray assembly being replaced.
4.
Holding the new fan tray assembly by the two retaining screws insert the
new fan tray assembly fully. The face plate of the fan tray will be flush
with the back face of the switch.
5.
Engage the retaining screws and tighten. Be sure to not over tighten the
screws.
Replacing Components
Replacing the Battery
Replacing the Battery
The battery is used to keep time for the internal switch clock. There is not
LED indicator for when the battery no longer has sufficient power. The only
indication will be the internal clock will not keep the correct time. The battery
is not hot swappable. Replacing the battery must be done during scheduled
downtime.
WARNING
■
The battery requires special handling at end-of-life. The battery
can explode or cause burns if disassembled, charged, or exposed
to water, fire or high temperature. After replacing the battery,
properly dispose of used battery according to instructions.
■
There is a risk of explosion if the battery is replaced by an
incorrect type. Ensure to replace the battery with the same type.
Installing a New Battery
WARNING
To avoid the possibility of electric shock, all power cords must be
disconnected from the switch and both power supplies must be
removed before starting this procedure. The top has an interlocking
mechanism that prohibits removal until the power supplies are
removed.
To install (or replace) a Battery:
1.
Disconnect the power cable(s) and remove both power supplies.
2.
Using a Torx T-8 screwdriver remove all the screws securing the top of
the switch and remove the top. The top is interlocked with the power
supplies and cannot be removed until the power supplies are removed.
3.
Remove the used battery and dispose of properly.
Replacing Components
Battery
4-3
Replacing Components
Replacing the Battery
AT T E N T I O N
4.
Insert a new battery with the lettering and the plus “+” sign facing up.
Be sure to replace with the same type of battery.
5.
Reinstall the top of the switch.
6.
Reinstall and tighten all the screws securing the top.
7.
Reconnect the power cable(s).
ll y a danger d'explosion s'il y a remplacement incorrect de la batterie.
Remplacer uniquement avec une batterie du même type ou d'un type
équivalent recommandé par le constructeur.
Mettre au rebut les batteries usagées conformément aux instructions du
fabricant.
AT T E N T I O N
If this product contains a real-time clock battery or coin cell battery it may
contain perchlorate and may require special handling when recycled or
disposed of in California and other certain states.
Perchlorate material - special handling may apply see:
Replacing Components
www.dtsc.ca.gov/hazardouswaste/perchlorate Web site for more
information."
4-4
Replacing Components
Replacing the Power Supplies
Replacing the Power Supplies
If your HP ProCurve Series 6600 Switch is configured with redundant power
supplies, the switch will not suffer any loss of traffic or performance if a power
supply fails. Replace the failed component as soon as possible. The PS (Power
Supply) LED will blink simultaneously with the switch Fault LED indicating
a power supply has failed.
To remove an AC power supply:
1.
Ensure the failed power supply is not plugged into an AC power source.
2.
Grasping the handle of the failed power supply release the locking
mechanism by squeezing the latch handle and remove the failed power
supply.
Latch release
handle
Power supply
handle
3.
4-5
Replacing Components
Insert the new power supply. Slide it in all the way in until the locking
mechanism locks.
Troubleshooting
Basic Troubleshooting Tips
5
Troubleshooting
Troubleshooting
This chapter describes how to troubleshoot your switch. This document
describes troubleshooting mostly from a hardware perspective. You can
perform more in-depth troubleshooting on the switch using the software tools
available with the switch, including the full-featured console interface, the
built-in web browser interface, and ProCurve Manager, the SNMP-based
network management tool. For more information, see the chapter “Troubleshooting” in the Management and Configuration Guide, which is on the
ProCurve Web site at www.procurve.com/manuals.
This chapter describes the following:
■
Basic Troubleshooting Tips (page 5-1)
■
Diagnosing with the LEDs (page 5-4)
■
Proactive Networking Tools (page 5-8)
■
Hardware Diagnostic Tests (page 5-9)
■
Restoring the Factory Default Configuration (page 5-11)
■
Downloading New Switch Software (page 5-12)
■
HP Customer Support Services (page 5-12)
Basic Troubleshooting Tips
Most problems are caused by the following situations. Check for these items
first when starting your troubleshooting:
■
Connecting to devices that have a fixed full-duplex configuration.
The RJ-45 ports are configured as “Auto”. That is, when connecting to
attached devices, the switch will operate in one of two ways to determine
the link speed and the communication mode (half duplex or full duplex):
•
If the connected device is also configured to Auto, the switch will
automatically negotiate both link speed and communication mode.
•
If the connected device has a fixed configuration, for example
100 Mbps, at half or full duplex, the switch will automatically sense
the link speed, but will default to a communication mode of half
duplex.
5-1
Troubleshooting
Basic Troubleshooting Tips
Troubleshooting
Caution
Because the switch behaves in this way (in compliance with the IEEE 802.3
standard), if a device connected to the switch has a fixed configuration at full
duplex, the device will not connect correctly to the switch. The result will be
high error rates and very inefficient communications between the switch and
the device.
Make sure all devices connected to the switch are configured to auto negotiate, or are configured to connect at half duplex (all hubs are configured this
way, for example).
■
Faulty or loose cables. Look for loose or obviously faulty connections.
If they appear to be OK, make sure the connections are snug. If that does
not correct the problem, try a different cable.
■
Non-standard cables. Non-standard and miswired cables may cause
network collisions and other network problems, and can seriously impair
network performance. Use a new correctly-wired cable or compare your
cable to the cable in appendix B, “Cables and Connectors” for pinouts and
correct cable wiring. A category 5 cable tester is a recommended tool for
every 100Base-TX and 1000Base-T network installation.
■
Improper Network Topologies. It is important to make sure you have
a valid network topology. Common topology faults include excessive
cable length and excessive repeater delays between end nodes. If you have
network problems after recent changes to the network, change back to
the previous topology. If you no longer experience the problems, the new
topology is probably at fault. Sample topologies are shown at the end of
chapter 2 in this book, and some topology configuration guidelines can
be found online on the ProCurve Web site at www.procurve.com/manuals.
In addition, you should make sure that your network topology contains
no data path loops. Between any two end nodes, there should be only
one active cabling path at any time. Data path loops will cause broadcast
storms that will severely impact your network performance.
For your switch, if you wish to build redundant paths between important
nodes in your network to provide some fault tolerance, you should enable
Spanning Tree Protocol support on the switch. This ensures only one
of the redundant paths is active at any time, thus avoiding data path loops.
Spanning Tree can be enabled through the switch console, the web
browser interface, or ProCurve Manager.
The Series 6600 Switch devices also support Trunking, which allows
multiple network cables to be used for a single network connection
without causing a data path loop. For more information on Spanning Tree
and Trunking, see the Management and Configuration Guide, which is
on the ProCurve Web site at www.procurve.com/manuals.
5-2
Troubleshooting
Basic Troubleshooting Tips
■
Use the switch console to determine the port’s configuration and verify
that there is not an improper or undesired configuration of any of the
switch features that may be affecting the port. For more information, see
the Management and Configuration Guide, which is on the ProCurve
Web site at www.procurve.com/manuals.
For more information on possible network problems and their solutions, refer
to the technical note “Troubleshooting LAN Performance and Intermittent
Connectivity Problems”, which can be found on the ProCurve Web site,
www.procurve.com/library, under “T” in the A-Z Index section.
5-3
Troubleshooting
Check the port configuration. A port on your switch may not be
operating as you expect because it has been put into a “blocking” state by
Spanning Tree, GVRP (automatic VLANs), or LACP (automatic trunking).
(Note that the normal operation of the Spanning Tree, GVRP, and LACP
features may put the port in a blocking state.) Or, the port just may have
been configured as disabled through software.
Troubleshooting
Diagnosing with the LEDs
Troubleshooting
Diagnosing with the LEDs
Table 5-1 shows LED patterns on the switch and the switch modules that
indicate problem conditions.
1.
Check in the table for the LED pattern you see on your switch.
2.
Refer to the corresponding diagnostic tip on the next few pages.
Table 5-1.
LED Error Indicators
LED Pattern Indicating Problems
Power
Fault
PS
Tmp
Test
Fan
Status
(in Link view mode)
Port LED
Diag
Tips
Off with
power cord
plugged in
*
PS LED off
or blinking
orange
*
*
*
*
➊
On
Prolonged On
*
*
Prolonged
On
*
*
➋
On
Blinking†
*
*
Blinking†
*
*
➌
On
Blinking†
*
*
Off
Blinking†
*
➍
On
Blinking†
*
*
Blinking†
*
Blinking†
➎
On
Off
*
*
Off
*
Off with cable
connected
➏
On
Off
*
*
Off
*
On, but the port is
not
communicating
➐
On
Blinking
Blinking
*
Off
*
*
➑
On
Blinking
*
Blinking
Off
*
*
➒
* This LED is not important for the diagnosis.
† The blinking behavior is an on/off cycle once every 1.6 seconds, approximately.
5-4
Troubleshooting
Diagnosing with the LEDs
Diagnostic Tips:
Problem
Solution
➊
The switch is not
plugged into an
active AC power
source, or the
switch’s power
supply may have
failed.
1. Verify the power cord is plugged into an active power source and to the switch. Make
sure these connections are snug.
2. Try power cycling the switch by unplugging and plugging the power cord back in.
3. If the Power LED is still not on, verify that the AC power source works by plugging
another device into the outlet. Or try plugging the switch into a different outlet or try a
different power cord.
If the power source and power cord are OK and this condition persists, the switch power
supply may have failed. Call your ProCurve authorized LAN dealer, or use the electronic
support services from ProCurve to get assistance. See the Customer Support/Warranty
booklet for more information.
➋
A switch
hardware failure
has occurred. All
the LEDs will stay
on indefinitely.
Try power cycling the switch. If the fault indication reoccurs, the switch may have failed.
Call your ProCurve authorized LAN dealer, or use the electronic support services from HP
to get assistance. See the Customer Support/Warranty booklet for more information.
➌
The switch has
experienced a
software failure
during self test.
1. Try resetting the switch by pressing the Reset button on the front of the switch, or by
power cycling the switch.
2. If the fault indication reoccurs, attach a console to the switch (as indicated in chapter
2) and configure it to operate at 9600 baud. Then, reset the switch. Messages should
appear on the console screen and in the console log identifying the error condition.
You can view the console log at that point by selecting it from the console Main Menu.
If necessary to resolve the problem, contact your ProCurve authorized LAN dealer, or use
the electronic support services from ProCurve to get assistance. See the Customer
Support/Warranty booklet for more information.
➍
One of the switch
cooling fans may
have failed.
Try disconnecting power from the switch and wait a few moments. Then reconnect the
power to the switch and check the LEDs again. If the error indication reoccurs, one of the
fans has failed. The other switch fans may continue to operate under this condition if the
ambient temperature does not exceed normal room temperature, but for best operation,
the fans should be replaced. Contact your ProCurve authorized LAN dealer, or use the
electronic support services from ProCurve to get assistance. See the Customer Support/
Warranty booklet for more information.
➎
The network port
for which the LED
is Blinking has
experienced a
self test or
initialization
failure.
Try power cycling the switch. If the fault indication reoccurs, the switch port may have
failed. Call your ProCurve authorized LAN dealer, or use the electronic support services
from ProCurve to get assistance. See the Customer Support/Warranty booklet for more
information.
If the port is a pluggable, verify it is one of the pluggables supported by the switch.
Unsupported pluggables will be identified with this fault condition. The supported miniGBICs are listed in Chapter 2, “Installing the Switch” on page 2-1. The mini-GBICs are
also tested when they are “hot-swapped” — installed or changed while the switch is
powered on. Also check the log file for error messages.
To verify the port has failed, try removing and reinstalling the mini-GBIC without having
to power off the switch. If the port fault indication reoccurs, you will have to replace the
mini-GBIC.
5-5
Troubleshooting
Tip
Troubleshooting
Diagnosing with the LEDs
Troubleshooting
Tip
Problem
Solution
continued on the next page
➏
The network
connection is not
working
properly.
Try the following procedures:
• For the indicated port, verify both ends of the cabling, at the switch and the connected
device, are connected properly.
• Verify the connected device and switch are both powered on and operating correctly.
• Verify you have used the correct cable type for the connection:
– For twisted-pair connections to the fixed 10/100 or 10/100/1000 ports, if the port is
configured to “Auto” (auto negotiate), either straight-through or crossover cables
can be used because of the switch’s “HP Auto-MDIX” feature and the Auto MDI/
MDI-X feature of the 10/100/1000-T port.
Note: If the switch port configuration is changed to one of the fixed configuration
options (for example, 100 Mbps/Full Duplex), then the port operates as MDI-X only
and you must use the correct type of cable for the connection. In general, for
connecting an end node (MDI port) to the switch, use straight-through cable; for
connecting to MDI-X ports on hubs, other switches, and routers, use crossover
cable.
•
•
•
•
•
5-6
– For fiber-optic connections, verify the transmit port on the switch is connected to
the receive port on the connected device, and the switch receive port is connected
to the transmit port on the connected device.
For the dual-personality 10/100/1000-T ports, be sure a mini-GBIC is not installed in the
associated slot.
For 1000Base-T connections, verify that the network cabling complies with the IEEE
802.3ab standard. the cable should be installed according to the ANSI/TIA/EIA-568A-5 specifications. Cable testing should comply with the stated limitations for Attenuation, Near-End Crosstalk, Far-End Crosstalk, Equal-Level Far-End Crosstalk (ELFEXT),
Multiple Disturber ELFEXT, and Return Loss.
The cable verification process must include all patch cables from any end devices,
including the switch, to any patch panels in the cabling path.
Verify the port has not been disabled through a switch configuration change.
You can use the console interface, or, if you have configured an IP address on the
switch, use the web browser interface, or ProCurve Manager network management
software to determine the state of the port and re-enable the port if necessary.
Verify the switch port configuration matches the configuration of the attached device.
For example, if the switch port is configured as “Auto”, the port on the attached device
also MUST be configured as “Auto”. Depending on the port type, twisted-pair or fiberoptic, if the configurations don’t match, the results could be a very unreliable connection, or no link at all.
If the other procedures don’t resolve the problem, try using a different port or a different
cable.
Troubleshooting
Diagnosing with the LEDs
Problem
Solution
➐
The port may be
improperly
configured, or
the port may be in
a “blocking”
state by the
normal operation
of the Spanning
Tree, LACP, or
IGMP features.
Use the switch console to see if the port is part of a dynamic trunk (through the LACP
feature) or to see if Spanning Tree is enabled on the switch, and to see if the port may
have been put into a “blocking” state by those features. The show lacp command displays
the port status for the LACP feature; the show spanning-tree command displays the port
status for Spanning Tree.
Also check the Port Status screen using the show interfaces command to see if the port
has been configured as “disabled”.
Other switch features that may affect the port operation include VLANs and IGMP. Use
the switch console to see how the port is configured for these features.
For software troubleshooting tips, see the chapter “Troubleshooting” in the Management
and Configuration Guide, which is on the ProCurve Web site at www.procurve.com/
manuals.
Make sure also, the device at the other end of the connection is indicating a good link to
the switch. If it is not, the problem may be with the cabling between the devices or the
connectors on the cable.
➑
A power supply
has failed in a
multi-power
supply switch.
Check the back of the switch to see which power supply has failed. The failed power
supply LED will be blinking. Replace the failed power supply. Once the failed power supply
is removed the LEDs will return to normal. If only one supply is inserted, try power cycling
the switch. If the fault reoccurs, the power supply may need to be replaced. If there are
two power supplies inserted but only one is connected, to remove the fault either connect
power to the other supply or remove it.
➒
The switch has
overheated.
Check to ensure the fans are functioning correctly.
5-7
Troubleshooting
Tip
Troubleshooting
Proactive Networking
Troubleshooting
Proactive Networking
The HP ProCurve Series 6600 Switches have built-in management capabilities
that proactively help you manage your network including:
■
finding and helping you fix the most common network error conditions
(for example, faulty network cabling, and non-standard network topologies)
■
informing you of the problem with clear, easy-to-understand messages
■
recommending network configuration changes to enhance the performance of your network
The following interfaces provide tests, indicators, and an event log that can
be used to monitor the switch and its network connections and to help you
take advantage of these proactive networking features:
■
ProCurve Manager - an SNMP-based network management tool that is
included with your switch.
■
A graphical web browser interface that you can use to manage your switch
from a PC running a supported web browser, for example Microsoft
Internet Explorer, and Netscape Communicator.
■
A full-featured easy-to-use console interface that you can access by
connecting a standard terminal or PC running a terminal emulator to the
switch’s console port. The cable to make that connection is provided with
your switch. The console interface is also accessible through a Telnet
connection.
For more information on using these software tools to diagnose and manage
your switch, see the “Troubleshooting” chapter in the Management and
Configuration Guide, which is on the ProCurve Web site at
www.procurve.com/manuals.
5-8
Troubleshooting
Hardware Diagnostic Tests
Testing the Switch by Resetting It
If you believe the switch is not operating correctly, you can reset the switch
to test its circuitry and operating code. To reset a switch, either:
■
unplug and plug in the power cord (power cycling)
■
press the Reset button on the front of the switch
Power cycling the switch and pressing the Reset button both cause the switch
to perform its power-on self test, which almost always will resolve any
temporary operational problems. These reset processes also cause any
network traffic counters to be reset to zero, and cause the System Up Time
timer to reset to zero.
Checking the Switch LEDs
The self test passes if the Fault and Self Test LEDs on the front of the switch
go off after approximately 50 seconds. If these LEDs stay on longer than 60
seconds or begin Blinking, there may be a problem with the switch.
See “Diagnosing With the LEDs” on page 5-4 for information on interpreting
the LED patterns and LED behaviors in chapter one.
Checking Console Messages
Useful diagnostic messages may be displayed on the console screen when the
switch is reset. As described in chapter 2 under step 7, “Connect a Console to
the Switch”, connect a PC running a VT-100 terminal emulator program or a
standard VT-100 terminal to the switch’s Console Port and configure it to run
at 9600 baud, and with the other terminal communication settings shown on
page 2-19. Then, when you reset the switch, note the messages that are
displayed. Additionally, you can check the switch event log, which can be
accessed from the console using the show log command, or from the console
Main Menu.
5-9
Troubleshooting
Hardware Diagnostic Tests
Troubleshooting
Hardware Diagnostic Tests
Testing Twisted-Pair Cabling
Troubleshooting
Network cables that fail to provide a link or provide an unreliable link between
the switch and the connected network device may not be compatible with the
IEEE 802.3 Type 10Base-T, 100Base-TX, or 1000Base-T standards. The twistedpair cables attached to the Switch must be compatible with the appropriate
standards. To verify your cable is compatible with these standards, use a
qualified cable test device.
Testing Switch-to-Device Network Communications
You can perform the following communication tests to verify the network is
operating correctly between the switch and any connected device that can
respond correctly to the communication test.
■
Link Test -- a physical layer test that sends IEEE 802.2 test packets to any
device identified by its MAC address.
■
Ping Test -- a network layer test used on IP networks that sends test
packets to any device identified by its IP address.
These tests can be performed through the switch console interface from a
terminal connected to the switch or through a Telnet connection, or from the
switch’s web browser interface. For more information, see the Management
and Configuration Guide, which is on the ProCurve Web site at
www.procurve.com/manuals.
These tests can also be performed from an SNMP network management
station running a program that can manage the switch, for example, ProCurve
Manager.
Testing End-to-End Network Communications
Both the switch and the cabling can be tested by running an end-to-end
communications test -- a test that sends known data from one network device
to another through the switch. For example, if you have two PCs on the
network that have LAN adapters between which you can run a link-level test
or Ping test through the switch, you can use this test to verify that the entire
communication path between the two PCs is functioning correctly. See your
LAN adapter documentation for more information on running a link test or
Ping test.
5-10
Troubleshooting
Restoring the Factory Default Configuration
As part of your troubleshooting process on the switch, it may become necessary to return the switch configuration to the factory default settings. This
process momentarily interrupts the switch operation, clears any passwords,
clears the console event log, resets the network counters to zero, performs a
complete self test, and reboots the switch into its factory default configuration
including deleting the IP address, if one is configured.
Note
This process removes all switch configuration changes you have made from
the factory default settings. This includes, for example, configuration of
VLANs, Spanning Tree, trunks, and stacking. Returning the configuration of
these features to their factory default settings (usually disabling them) may
result in network connectivity issues.
If the switch has a valid configuration, and you are restoring the factory default
settings for a reason other than configuration problems, you should save the
switch configuration prior to performing the factory default reset. Then, after
the reset and resolution of the original problem, you can restore the saved
configuration to the switch. For both the save and restore processes, you can
use the console copy command. For more information on this command, see
the Management and Configuration Guide, which is on the ProCurve Web
site at www.procurve.com/manuals.
You can restore the factory default configuration either on the switch itself,
or through the switch console.
To execute the factory default reset on the switch, perform these steps:
1.
Using pointed objects, simultaneously press both the Reset and Clear
buttons on the front of the switch.
2.
Continue to press the Clear button while releasing the Reset button.
3.
When the Self Test LED begins to blink, release the Clear button.
The switch will then complete its self test and begin operating with its
configuration restored to the factory default settings.
To restore the factory default configuration using the console, execute the
erase startup-config command from the console command prompt.
5-11
Troubleshooting
Restoring the Factory Default
Configuration
Troubleshooting
Downloading New Switch Software
Troubleshooting
Downloading New Switch Software
When product enhancements occur for the switch, new software can be
downloaded to the switch through several methods, for product enhancements and new features. For more information, see the Management and
Configuration Guide, which is on the ProCurve Web site at
www.procurve.com/manuals
The new switch software would be available on the ProCurve Web site at
www.procurve.com/software.
HP Customer Support Services
If you are still having trouble with your switch, Hewlett-Packard offers support
24 hours a day, seven days a week through the use of a number of automated
electronic services. See the Customer Support/Warranty booklet that came
with your switch for information on how to use these services to get technical
support. The ProCurve Web site at www.procurve.com/support also provides
up-to-date support information.
Additionally, your ProCurve authorized network reseller can provide you with
assistance, both with services that they offer and with services offered by
ProCurve.
Before Calling Support
Before calling your networking dealer or ProCurve Support, to make the
support process most efficient, you first should have retrieved the following
information:
5-12
Information Item
Information Location
• product identification, including miniGBICs
the front of the switch and on labels on the
mini-GBICs
• details about the switch’s status including the software (OS) version, a copy of
the switch configuration, a copy of the
switch Event Log, and a copy of the
switch status and counters information
switch console: show tech command
• copy of your network topology map, including network addresses assigned to
the relevant devices
your network records
A
Specifications
Physical
HP ProCurve 6600-24XG
Switch (J9265A)
Width:
44.3 cm (17.42 in)
44.3 cm (17.42 in)
44.3 cm (17.42 in)
Depth:
51.1 cm (20.1 in)
51.1 cm (20.1 in)
59.9 cm (23.6 in)
Height:
4.4 cm (1.7 in)
4.4 cm (1.7 in)
4.4 cm (1.7 in)
Weight:
7.68 kg (16.93) lbs)
7.7 kg (16.97 lbs)
9.33 kg (20.6 lbs)
Specifications
HP ProCurve 6600-24G Switch HP ProCurve 6600-24G-4XG
(J9263A)
Switch (J9264A)
Electrical
The switch automatically adjusts to any voltage between 100-127 and 200-240
volts and either 50 or 60 Hz.
Applicable Products
Electrical
AC voltage:
Maximum current:
Frequency range:
HP ProCurve 6600-24G Switch HP ProCurve 6600-24G-4XG
(J9263A)
Switch (J9264A)
HP ProCurve 6600-24XG
Switch (J9265A)
100-127/200-240 volts
1.8A/0.9A
50/60 Hz
100-127/200-240 volts
4.2A/2.2A
50/60 Hz
100-127/200-240 volts
2.1A/1.1A
50/60 Hz
The switch automatically adjusts to any voltage between 100-127 and 200-240 volts and either 50 or 60 Hz.
Environmental
Operating
Non-Operating
Temperature:
5°C to 40°C (41°F to 104°F)
-40°C to 70°C (-40°F to 158°F)
Relative humidity:
(non-condensing)
15% to 80% at 40°C (104°F)
20% to 90% at 70°C (158°F)
Maximum altitude:
3.0 km (10,000 ft)
4.6 km (15,000 ft)
A-1
Specifications
Acoustic
HP ProCurve Switch 6600-24G (J9263A)
Geraeuschemission LpA=62.3 dB am fiktiven Arbeitsplatz nach
DIN 45635 T.19
Noise Emission LpA=49.3 dB at virtual workspace according to
DIN 45635 T.19
HP ProCurve Switch 6600-28G-4XG (J9264A)
Geraeuschemission LpA=59.5 dB am fiktiven Arbeitsplatz nach
DIN 45635 T.19
Specifications
Noise Emission LpA=52 dB at virtual workspace according to
DIN 45635 T.19
HP ProCurve Switch 6600-24G-24XG (J9265A)
Geraeuschemission LpA=61.8 dB am fiktiven Arbeitsplatz nach
DIN 45635 T.19
Noise Emission LpA=49.3 dB at virtual workspace according to
DIN 45635 T.19
Safety
Complies with:
A-2
■
EN60950-1
■
CSA 22.2 No. 60950-1
■
UL 60950-1
■
IEC 60950-1
Specifications
Table A-1.
Technology standards and safety compliance
Laser safety information
Technology
Compatible with these IEEE
standards
Safety
standard
compliance
SFP (“mini-GBIC”)
Lasers
SFP+
Lasers
IEEE 802.3 10BASE-T,
IEEE 802.3u 100BASE-TX,
IEEE 802.3ab 1000BASE-T
100-FX
IEEE 802.3u 100BASE-FX
EN/IEC
60825
Class 1 Laser Product
Laser Klasse 1
100-BX
IEEE 802.3ah 100BASE-BX10
EN/IEC
60825
Class 1 Laser Product
Laser Klasse 1
1000-SX
IEEE 802.3z 1000BASE-SX
EN/IEC
60825
Class 1 Laser Product
Laser Klasse 1
1000-LX
IEEE 802.3z 1000BASE-LX
EN/IEC
60825
Class 1 Laser Product
Laser Klasse 1
1000-LH
(not an IEEE standard)
EN/IEC
60825
Class 1 Laser Product
Laser Klasse 1
1000-BX
IEEE 802.3ah 1000BASE-BX10
EN/IEC
60825
Class 1 Laser Product
Laser Klasse 1
10-Gig
Direct Attach
(not an IEEE standard)
10-Gig SR
IEEE 802.3ae 10GBASE-SR
EN/IEC
60825
Class 1 Laser Product
Laser Klasse 1
10-Gig LRM
IEEE 802.3aq 10GBASE-LRM
EN/IEC
60825
Class 1 Laser Product
Laser Klasse 1
10-Gig LR
IEEE 802.3ae 10GBASE-LR
EN/IEC
60825
Class 1 Laser Product
Laser Klasse 1
Specifications
10/100/1000-T
A-3
B
Cabling and Technology Information
This appendix includes network cable information for cables that should be
used with the Switch 6600, including minimum pin-out information and
specifications for twisted-pair cables.
Note
Incorrectly wired cabling is the most common cause of problems for LAN
communications. ProCurve recommends that you work with a qualified LAN
cable installer for assistance with your cabling requirements.
Cabling specifications
Table B-1.
Twisted-pair copper
Category 3, 4, or 5 100-ohm unshielded twisted-pair (UTP) or
shielded twisted-pair (STP) cable, complying with IEEE 802.3
10Base-T specifications.
100 Mbps Operation
Category 5 100-ohm UTP or STP cable, complying with IEEE
802.3u 100Base-TX specifications.
1000 Mbps Operation
Category 5 100-ohm 4-pair UTP or STP cable, complying with IEEE
802.3ab 1000Base-T specifications—Category 5e or better is
recommended. See note on 1000Base-T Cable Requirements on
page B-2.
Direct attach cables
One-piece devices consisting of a cable with SFP+ connectors
permanently attached to each end, complying with SFF 8431 SFP+
specifications.
Multimode fiber
62.5/125 μm or 50/125 μm (core/cladding) diameter, low metal
content, graded index fiber-optic cables, complying with the
ITU-T G.651 and ISO/IEC 793-2 Type A1b or A1a standards
respectively.1
Single mode fiber
9/125 μm (core/cladding) diameter, low metal content fiber-optic
cables, complying with the ITU-T G.652 and
ISO/IEC 793-2 Type B1 standards.
1
A mode conditioning patch cord may be needed for some Gigabit-LX and 10-Gigabit LRM installations.
See “Mode Conditioning Patch Cord” on page B-4 for more information.
B-1
Cabling and Technology
Information
Twinaxial copper
10 Mbps Operation
Cabling and Technology Information
Note on 1000Base-T Cable Requirements. The Category 5 networking
cables that work for 100Base-TX connections should also work for
1000Base-T, as long as all four-pairs are connected. But, for the most robust
connections you should use cabling that complies with the Category 5e
specifications, as described in Addendum 5 to the TIA-568-A standard (ANSI/
TIA/EIA-568-A-5).
Because of the increased speed provided by 1000Base-T (Gigabit-T), network
cable quality is more important than for either 10Base-T or 100Base-TX.
Cabling plants being used to carry 1000Base-T networking must comply with
the IEEE 802.3ab standards. In particular, the cabling must pass tests for
Attenuation, Near-End Crosstalk (NEXT), and Far-End Crosstalk (FEXT).
Additionally, unlike the cables for 100Base-TX, the 1000Base-T cables must
pass tests for Equal-Level Far-End Crosstalk (ELFEXT) and Return Loss.
Cabling and Technology
Information
When testing your cabling, be sure to include the patch cables that connect
the switch and other end devices to the patch panels on your site. The patch
cables are frequently overlooked when testing cable and they must also
comply with the cabling standards.
B-2
Cabling and Technology Information
Technology distance specifications
Table B-2.
Supported cable type
Multimode fiber
modal bandwidth
Supported distances
100-FX
multimode fiber
any
up to 2,000 meters
100-BX
single mode fiber
N/A
0.5 - 10,000 meters
1000-T
twisted-pair copper
N/A
up to 100 meters
1000-SX
multimode fiber
160 MHz*km
200 MHz*km
400 MHz*km
500 MHz*km
2 - 220 meters
2 - 275 meters
2 - 500 meters
2 - 550 meters
1000-LX
multimode fiber
single mode fiber
400 MHz*km
500 MHz*km
N/A
2 - 550 meters
2 - 550 meters
2 - 10,000 meters
1000-LH
single mode fiber
N/A
10 - 70,000 meters1
1000-BX
single mode fiber
N/A
0.5 - 10,000 meters
10-Gig Direct Attach
twinaxial copper
N/A
(various lengths offered)
10-Gig SR
multimode fiber
160 MHz*km
200 MHz*km
400 MHz*km
500 MHz*km
2000 MHz*km
2 - 26 meters
2 - 33 meters
2 - 66 meters
2 - 82 meters
2 - 300 meters
10-Gig LRM
multimode fiber
400 MHz*km
500 MHz*km
0.5 - 100 meters
0.5 - 220 meters
10-Gig LR
single mode fiber
N/A
2 - 10,000 meters
1
Cabling and Technology
Information
Technology
For distances less than 20km, a 10dB attenuator must be used. For distances between 20km and 40km,
a 5dB attenuator must be used. Attenuators can be purchased from most cable vendors.
B-3
Cabling and Technology Information
Mode Conditioning Patch Cord
Mode Conditioning Patch Cord
The following information applies to installations in which multimode fiberoptic cables are connected to a Gigabit-LX port or a 10-Gigabit LRM port.
Multimode cable has a design characteristic called “Differential Mode Delay”,
which requires the transmission signals be “conditioned” to compensate for
the cable design and thus prevent resulting transmission errors.
Under certain circumstances, depending on the cable used and the lengths of
the cable runs, an external Mode Conditioning Patch Cord may need to be
installed between the Gigabit-LX or 10-Gigabit LRM transmitting device and
the multimode network cable to provide the transmission conditioning. If you
experience a high number of transmission errors on those ports, usually CRC
or FCS errors, you may need to install one of these patch cords between the
fiber-optic port in your switch and your multimode fiber-optic network
cabling, at both ends of the network link.
Cabling and Technology
Information
The patch cord consists of a short length of single mode fiber cable coupled
to graded-index multimode fiber cable on the transmit side, and only
multimode cable on the receive side. The section of single mode fiber is
connected in such a way that it minimizes the effects of the differential mode
delay in the multimode cable.
Note
Most of the time, if you are using good quality graded-index multimode fiber
cable that adheres to the standards listed in Appendix B, there should not be
a need to use mode conditioning patch cords in your network. This is
especially true if the fiber runs in your network are relatively short.
For 10-Gigabit LRM using OM3 cable (50 μm multimode @ 1500/500 MHz*km),
a mode conditioning patch cord is not required. Other multimode cables may
require mode conditioning patch cords to achieve the LRM maximum
distances.
B-4
Cabling and Technology Information
Mode Conditioning Patch Cord
Installing the Patch Cord
As shown in the illustration below, connect the patch cord to the ProCurve
transceiver with the section of single mode fiber plugged in to the Tx
(transmit) port. Then, connect the other end of the patch cord to your network
cabling patch panel, or directly to the network multimode fiber.
To network
multimode
cabling
The multimode cable in the patch cord
must match the characteristics of your
network cable
Tx
Gigabit-LX port
Rx
If you connect the patch cord directly to the network cabling, you may need
to install a female-to-female adapter to allow the cables to be connected
together.
Mode Conditioning
Patch Cord
Single-mode section plugs into Tx
port on Gigabit-LX Transceiver or
Gigabit-LX mini-GBIC
Make sure you purchase a patch cord that has appropriate connectors on each
end, and has multimode fibers that match the characteristics of the multimode
fiber in your network. Most important, the core diameter of the multimode
patch cord must match the core diameter of the multimode cable
infrastructure (either 50 or 62.5 microns).
B-5
Cabling and Technology
Information
Figure B-1. Example: Connecting a Mode Conditioning Patch Cord for Gigabit-LX
Cabling and Technology Information
Twisted-Pair Cable/Connector Pin-Outs
Twisted-Pair Cable/Connector Pin-Outs
Auto-MDIX Feature: The 10/100/1000-T ports support the IEEE 802.3ab
standard, which includes the “Auto MDI/MDI-X” feature. In the default
configuration, “Auto”, the ports on the Switch 6600 all automatically detect
the type of port on the connected device and operate as either an MDI or MDIX port, whichever is appropriate. So for any connection, a straight-through
twisted-pair cable can be used -- you no longer have to use crossover cables,
although crossover cables can also be used for any of the connections.
If you connect a Switch 6600 twisted-pair port to another switch or hub, which
typically have MDI-X ports, the Switch 6600 port automatically operates as an
MDI port. If you connect it to an end node, such as a server or PC, which
typically have MDI ports, the Switch 6600 port operates as an MDI-X port. In
all cases, you can use standard straight-through cables or crossover cables.
If you happen to use a correctly wired crossover cable, though, the switch will
still be able to automatically detect the MDI/MDI-X operation and link
correctly to the connected device.
Cabling and Technology
Information
Other Wiring Rules:
B-6
■
All twisted-pair wires used for 10 Mbps, and 100 Mbps operation must be
twisted through the entire length of the cable. The wiring sequence must
conform to EIA/TIA 568-B (not USOC). See “Twisted-Pair Cable Pin
Assignments” later in this appendix for a listing of the signals used on each
pin.
■
For 1000Base-T connections, all four pairs of wires in the cable must be
available for data transmission. See “Note on 1000Base-T Cable Requirements” on page B-2 for more information on 1000Base-T cabling.
■
For 10 Mbps connections to the ports, you can use Category 3, 4, or 5
unshielded twisted-pair cable, as supported by the IEEE 802.3 Type
10Base-T standard.
■
For 100 Mbps connections to the ports, use 100-ohm Category 5 UTP or
STP cable only, as supported by the IEEE 802.3u Type 100Base-TX standard.
■
For 1000 Mbps connections, 100-ohm Category 5e or better cabling is
recommended.
Cabling and Technology Information
Twisted-Pair Cable/Connector Pin-Outs
Straight-Through Twisted-Pair Cable for
10 Mbps or 100 Mbps Network Connections
Because of the HP Auto-MDIX operation of the 10/100 ports on the switch, for
all network connections, to PCs, servers or other end nodes, or to hubs or
other switches, you can use straight-through cables.
If any of these ports are given a fixed configuration, for example 100 Mbps/
Full Duplex, the ports operate as MDI-X ports, and straight-through cables
must be then used for connections to PC NICs and other MDI ports.
Cable Diagram
Pins 1 and 2 on connector “A” must be wired as a twisted pair to pins 1 and 2
on connector “B”.
Pins 3 and 6 on connector “A” must be wired as a twisted pair to pins 3 and 6
on connector “B”.
Pins 4, 5, 7, and 8 are not used in this application, although they may be wired
in the cable.
.
Pin Assignments
Switch End (MDI-X)
Computer, Transceiver, or
Other End
Signal
Pins
Pins
Signal
receive +
receive transmit +
transmit -
1
2
3
6
1
2
3
6
transmit +
transmit receive +
receive -
B-7
Cabling and Technology
Information
Note
Cabling and Technology Information
Twisted-Pair Cable/Connector Pin-Outs
Crossover Twisted-Pair Cable for
10 Mbps or 100 Mbps Network Connection
The HP Auto-MDIX operation of the 10/100 ports on the switch also allows
you to use crossover cables for all network connections, to PCs, servers or
other end nodes, or to hubs or other switches.
If any of these ports are given a fixed configuration, for example 100 Mbps/
Full Duplex, the ports operate as MDI-X ports, and crossover cables must be
then used for connections to hubs or switches or other MDI-X network
devices.
Cabling and Technology
Information
Cable Diagram
Note
Pins 1 and 2 on connector “A” must be wired as a twisted pair to pins 3 and 6
on connector “B”.
Pins 3 and 6 on connector “A” must be wired as a twisted pair to pins 1 and 2
on connector “B”.
Pins 4, 5, 7, and 8 are not used in this application, although they may be wired
in the cable.
.
Pin Assignments
B-8
Switch End (MDI-X)
Hub or Switch Port, or Other
MDI-X Port End
Signal
Pins
Pins
Signal
receive +
receive transmit +
transmit -
1
2
3
6
6
3
2
1
transmit transmit +
receive receive +
Cabling and Technology Information
Twisted-Pair Cable/Connector Pin-Outs
Straight-Through Twisted-Pair Cable for
1000 Mbps Network Connections
1000Base-T connections require that all four pairs or wires be connected.
Cable Diagram
Pins 1 and 2 on connector “A” must be wired as a twisted pair to pins 1 and 2
on connector “B”.
Pins 3 and 6 on connector “A” must be wired as a twisted pair to pins 3 and 6
on connector “B”.
Pins 4 and 5 on connector “A” must be wired as a twisted pair to pins 4 and 5
on connector “B”.
Pins 7 and 8 on connector “A” must be wired as a twisted pair to pins 7 and 8
on connector “B”.
.
Pin Assignments
For 1000Base-T operation, all four pairs of wires are used for both transmit
and receive.
B-9
Cabling and Technology
Information
Note
C
Safety and EMC Regulatory Statements
Safety Information
!
Documentation reference symbol. If the product is marked with this
symbol, refer to the product documentation to get more information
about the product.
WARNING
A WARNING in the manual denotes a hazard that can cause injury
or death.
Caution
A Caution in the manual denotes a hazard that can damage equipment.
Do not proceed beyond a WARNING or Caution notice until you
have understood the hazardous conditions and have taken appropriate steps.
Grounding
These are safety class I products and have protective earthing terminals. There
must be an uninterruptible safety earth ground from the main power source
to the product's input wiring terminals, power cord, or supplied power cord
set. Whenever it is likely that the protection has been impaired, disconnect
the power cord until the ground has been restored.
For LAN cable grounding:
■
If your LAN covers an area served by more than one power distribution system, be sure their safety grounds are securely interconnected.
■
LAN cables may occasionally be subject to hazardous transient voltages (such as lightning or disturbances in the electrical utilities power
grid). Handle exposed metal components of the network with caution.
These products do not have a power switch; they are powered on when the
power cord is plugged in.
C-1
Safety and EMC Regulatory
Statements
Servicing
There are no user-serviceable parts inside these products. Any servicing,
adjustment, maintenance, or repair must be performed only by service-trained
personnel.
Safety and EMC Regulatory Statements
Informations concernant la sécurité
Informations concernant la sécurité
!
Symbole de référence à la documentation. Si le produit est marqué de
ce symbole, reportez-vous à la documentation du produit afin d'obtenir
des informations plus détaillées.
WARNING
Dans la documentation, un WARNING indique un danger susceptible
d'entraîner des dommages corporels ou la mort.
Caution
Un texte de mise en garde intitulé Caution indique un danger susceptible de causer des dommages à l'équipement.
Ne continuez pas au-delà d'une rubrique WARNING ou Caution avant
d'avoir bien compris les conditions présentant un danger et pris les
mesures appropriées.
Cet appareil est un produit de classe I et possède une borne de mise à la terre. La source
d'alimentation principale doit être munie d'une prise de terre de sécurité installée aux
bornes du câblage d'entrée, sur le cordon d'alimentation ou le cordon de raccordement
fourni avec le produit. Lorsque cette protection semble avoir été endommagée,
débrancher le cordon d'alimentation jusqu'à ce que la mise à la terre ait été réparée.
Mise à la terre du câble de réseau local:
■
si votre réseau local s'étend sur une zone desservie par plus d'un système de
distribution de puissance, assurez-vous que les prises de terre de sécurité
soient convenablement interconnectées.
■
Les câbles de réseaux locaux peuvent occasionnellement être soumis à des
surtensions transitoires dangereuses (telles que la foudre ou des perturbations dans le réseau d'alimentation public). Manipulez les composants
métalliques du réseau avec précautions.
Aucune pièce contenue à l'intérieur de ce produit ne peut être réparée par l'utilisateur.
Tout dépannage, réglage, entretien ou réparation devra être confié exclusivement à un
personnel qualifié.
Safety and EMC Regulatory
Statements
Cet appareil ne comporte pas de commutateur principal ; la mise sous tension est
effectuée par branchement du cordon d'alimentation.
C-2
Safety and EMC Regulatory Statements
Hinweise zur Sicherheit
Hinweise zur Sicherheit
!
Symbol für Dokumentationsverweis. Wenn das Produkt mit diesem
Symbol markiert ist, schlagen Sie bitte in der Produktdokumentation
nach, um mehr Informationen über das Produkt zu erhalten.
WARNING
Eine WARNING in der Dokumentation symbolisiert eine Gefahr, die
Verletzungen oder sogar Todesfälle verursachen kann.
Caution
Caution in der Dokumentation symbolisiert eine Gefahr, die dis Gerät
beschädigen kann.
Fahren Sie nach dem Hinweis WARNING oder Caution erst fort,
nachdem Sie den Gefahrenzustand verstanden und die entsprechenden Maßnahmen ergriffen haben.
Dies ist ein Gerät der Sicherheitsklasse I und verfügt über einen schützenden Erdungsterminal. Der Betrieb des Geräts erfordert eine ununterbrochene Sicherheitserdung
von der Hauptstromquelle zu den Geräteingabeterminals, den Netzkabeln oder dem
mit Strom belieferten Netzkabelsatz voraus. Sobald Grund zur Annahme besteht, daß
der Schutz beeinträchtigt worden ist, das Netzkabel aus der Wandsteckdose
herausziehen, bis die Erdung wiederhergestellt ist.
Für LAN-Kabelerdung:
■
Wenn Ihr LAN ein Gebiet umfaßt, das von mehr als einem Stromverteilungssystem beliefert wird, müssen Sie sich vergewissern, daß die
Sicherheitserdungen fest untereinander verbunden sind.
■
LAN-Kabel können gelegentlich gefährlichen Übergangsspannungen ausgesetzt werden (beispielsweise durch Blitz oder Störungen in dem
Starkstromnetz des Elektrizitätswerks). Bei der Handhabung exponierter
Metallbestandteile des Netzwerkes Vorsicht walten lassen.
Dieses Gerät enthält innen keine durch den Benutzer zu wartenden Teile. Wartungs-,
Anpassungs-, Instandhaltungs- oder Reparaturarbeiten dürfen nur von geschultem
Bedienungspersonal durchgeführt werden.
Safety and EMC Regulatory
Statements
Dieses Gerät hat keinen Netzschalter; es wird beim Anschließen des Netzkabels
eingeschaltet.
C-3
Safety and EMC Regulatory Statements
Considerazioni sulla sicurezza
Considerazioni sulla sicurezza
!
Simbolo di riferimento alla documentazione. Se il prodotto è
contrassegnato da questo simbolo, fare riferimento alla documentazione sul prodotto per ulteriori informazioni su di esso.
WARNING
La dicitura WARNINGdenota un pericolo che può causare lesioni o
morte.
Caution
La dicituraCaution denota un pericolo che può danneggiare le attrezzature.
Non procedere oltre un avviso di WARNING o di Cautionprima di
aver compreso le condizioni di rischio e aver provveduto alle misure
del caso.
Questo prodotto è omologato nella classe di sicurezza I ed ha un terminale protettivo
di collegamento a terra. Dev'essere installato un collegamento a terra di sicurezza, non
interrompibile che vada dalla fonte d'alimentazione principale ai terminali d'entrata,
al cavo d'alimentazione oppure al set cavo d'alimentazione fornito con il prodotto.
Ogniqualvolta vi sia probabilità di danneggiamento della protezione, disinserite il cavo
d'alimentazione fino a quando il collegaento a terra non sia stato ripristinato.
Per la messa a terra dei cavi LAN:
■
se la vostra LAN copre un'area servita da più di un sistema di distribuzione
elettrica, accertatevi che i collegamenti a terra di sicurezza siano ben collegati
fra loro;
■
i cavi LAN possono occasionalmente andare soggetti a pericolose tensioni
transitorie (ad esempio, provocate da lampi o disturbi nella griglia d'alimentazione della società elettrica); siate cauti nel toccare parti esposte in
metallo della rete.
Safety and EMC Regulatory
Statements
Nessun componente di questo prodotto può essere riparato dall'utente. Qualsiasi
lavoro di riparazione, messa a punto, manutenzione o assistenza va effettuato esclusivamente da personale specializzato.
Questo apparato non possiede un commutatore principale; si mette scotto tensione
all'inserirsi il cavo d'alimentazione.
C-4
Safety and EMC Regulatory Statements
Consideraciones sobre seguridad
Consideraciones sobre seguridad
!
Símbolo de referencia a la documentación. Si el producto va
marcado con este símbolo, consultar la documentación del
producto a fin de obtener mayor información sobre el producto.
WARNING
Una WARNING en la documentación señala un riesgo que podría
resultar en lesiones o la muerte.
Caution
Una Caution en la documentación señala un riesgo que podría
resultar en averías al equipo.
No proseguir después de un símbolo de WARNING o Caution hasta
no haber entendido las condiciones peligrosas y haber tomado las
medidas apropiadas.
Este aparato se enmarca dentro de la clase I de seguridad y se encuentra protegido por
una borna de puesta a tierra. Es preciso que exista una puesta a tierra continua desde
la toma de alimentación eléctrica hasta las bornas de los cables de entrada del aparato,
el cable de alimentación o el juego de cable de alimentación suministrado. Si existe la
probabilidad de que la protección a tierra haya sufrido desperfectos, desenchufar el
cable de alimentación hasta haberse subsanado el problema.
Puesta a tierra del cable de la red local (LAN):
■
Si la LAN abarca un área cuyo suministro eléctrico proviene de más de una
red de distribución de electricidad, cerciorarse de que las puestas a tierra
estén conectadas entre sí de modo seguro.
■
Es posible que los cables de la LAN se vean sometidos de vez en cuando a
voltajes momentáneos que entrañen peligro (rayos o alteraciones en la red
de energía eléctrica). Manejar con precaución los componentes de metal de
la LAN que estén al descubierto.
Este aparato no contiene pieza alguna susceptible de reparación por parte del usuario.
Todas las reparaciones, ajustes o servicio de mantenimiento debe realizarlos solamente el técnico.
C-5
Safety and EMC Regulatory
Statements
Este producto no tiene interruptor de potencia; se activa cuando se enchufa el cable
de alimentación.
Safety and EMC Regulatory Statements
Safety Information (Japan)
Safety and EMC Regulatory
Statements
Safety Information (Japan)
Japan Power
Cord Warning
C-6
Safety and EMC Regulatory Statements
Safety Information (China)
Safety Information (China)
Safety and EMC Regulatory
Statements
C-7
Safety and EMC Regulatory Statements
EMC Regulatory Statements
EMC Regulatory Statements
U.S.A.
FCC Class A
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause interference to radio communications.
Operation of this equipment in a residential area may cause interference in which case the user
will be required to correct the interference at his own expense.
Canada
This product complies with Class A Canadian EMC requirements.
Australia/New Zealand
This product complies with Australia/New Zealand EMC Class A requirements.
Japan
VCCI Class A
Safety and EMC Regulatory
Statements
Korea
Taiwan
C-8
Safety and EMC Regulatory Statements
EMC Regulatory Statements
European Community
DECLARATION OF CONFORMITY
according to ISO/IEC 17050-1 and EN 17050-1
Supplier’s Name:
Manufacturer's Address:
DoC #: RSVLC-0704-091608
Hewlett-Packard Company
8000 Foothills Blvd., Roseville, CA 95747 U.S.A.
declares, that the product
Product Name2:
HP ProCurve 6600 - 24G
HP ProCurve 6600 - 24G-4XG
HP ProCurve 6600 - 24XG
Product Number(s): J9263A, J9266A
J9264A, J9267A
J9265A, J9268A
Regulatory Model No1: RSVLC-0704
Product Options:
J9269A
conforms to the following Product Specifications and Regulations:
EMC: Class A
EN 55022:2006
EN 55024:2001+A2 (2003)
EN 61000-3-2:2006
EN 61000-3-3:1995 +A1 (2001) +A2 (2005)
FCC CFR47 Part 15
Safety:
EN 60950-1:2001
IEC 60950-1: 2001
EN 60825-1:1994 +A1+A2 / IEC 60825-1:1993 +A2 Class 1
Supplementary Information:
The device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
The product herewith complies with the requirements of the Low Voltage Directive 2006/95/EC, the EMC Directive
2004/108/EC and carries the CE marking accordingly.
Additional Information:
1) This product is assigned a Regulatory Model Number which stays with the regulatory aspects of the design. The Regulatory Model
Number is the main product identifier in the regulatory documentation and test reports, this number should not be confused with the
marketing name or the product numbers.
2) This product was tested with HP branded products only.
Safety and EMC Regulatory
Statements
Roseville, 16-September-2008
Local contact for regulatory information:
EMEA: Hewlett-Packard GmbH, HQ-TRE, Herrenberger Straße 140, D-71034 Böblingen, Germany
U.S.:
Hewlett-Packard, 3000 Hanover St., Palo Alto, CA 94304, U.S.A. 650-857-1501
C-9
D
Recycle Statements
Recycle Statements
Waste Electrical and Electronic
Equipment (WEEE) Statements
Disposal of Waste Equipment by Users in Private Household in the European Union
This symbol on the product or on its packaging indicates that this product must not be disposed of with
your other household waste. Instead, it is your responsibility to dispose of your waste equipment by
handing it over to a designated collection point for the recycling of waste electrical and electronic
equipment. The separate collection and recycling of your waste equipment at the time of disposal will
help to conserve natural resources and ensure that it is recycled in a manner that protects human health
and the environment. For more information about where you can drop off your waste equipment for
recycling, please contact your local city office, your household waste disposal service or the shop where
you purchased the product.
Likvidace zařízení soukromými domácími uživateli v Evropské unii
Tento symbol na produktu nebo balení označuje výrobek, který nesmí být vyhozen spolu s ostatním
domácím odpadem. Povinností uživatele je předat takto označený odpad na předem určené sběrné
místo pro recyklaci elektrických a elektronických zařízení. Okamžité třídění a recyklace odpadu
pomůže uchovat přírodní prostředí a zajistí takový způsob recyklace, který ochrání zdraví a životní
prostředí člověka. Další informace o možnostech odevzdání odpadu k recyklaci získáte na
příslušném obecním nebo městském úřadě, od firmy zabývající se sběrem a svozem odpadu nebo v
obchodě, kde jste produkt zakoupili.
Bortskaffelse af affald fra husstande i den Europæiske Union
Hvis produktet eller dets emballage er forsynet med dette symbol, angiver det, at produktet ikke må
bortskaffes med andet almindeligt husholdningsaffald. I stedet er det dit ansvar at bortskaffe kasseret
udstyr ved at aflevere det på den kommunale genbrugsstation, der forestår genvinding af kasseret
elektrisk og elektronisk udstyr. Den centrale modtagelse og genvinding af kasseret udstyr i forbindelse
med bortskaffelsen bidrager til bevarelse af naturlige ressourcer og sikrer, at udstyret genvindes på en
måde, der beskytter både mennesker og miljø. Yderligere oplysninger om, hvor du kan aflevere kasseret
udstyr til genvinding, kan du få hos kommunen, den lokale genbrugsstation eller i den butik, hvor du købte
produktet.
Seadmete jäätmete kõrvaldamine eramajapidamistes Euroopa Liidus
See tootel või selle pakendil olev sümbol näitab, et kõnealust toodet ei tohi koos teiste majapidamisjäätmetega kõrvaldada. Teie kohus on oma seadmete jäätmed kõrvaldada, viies need elektri- ja elektroonikaseadmete jäätmete ringlussevõtmiseks selleks ettenähtud kogumispunkti. Seadmete jäätmete eraldi
kogumine ja ringlussevõtmine kõrvaldamise ajal aitab kaitsta loodusvarasid ning tagada, et ringlussevõtmine toimub viisil, mis kaitseb inimeste tervist ning keskkonda. Lisateabe saamiseks selle kohta, kuhu
oma seadmete jäätmed ringlussevõtmiseks viia, võtke palun ühendust oma kohaliku linnakantselei,
majapidamisjäätmete kõrvaldamise teenistuse või kauplusega, kust Te toote ostsite.
D-1
Recycle Statements
Waste Electrical and Electronic Equipment (WEEE) Statements
Recycle Statements
Laitteiden hävittäminen kotitalouksissa Euroopan unionin alueella
Jos tuotteessa tai sen pakkauksessa on tämä merkki, tuotetta ei saa hävittää kotitalousjätteiden mukana.
Tällöin hävitettävä laite on toimitettava sähkölaitteiden ja elektronisten laitteiden kierrätyspisteeseen.
Hävitettävien laitteiden erillinen käsittely ja kierrätys auttavat säästämään luonnonvaroja ja
varmistamaan, että laite kierrätetään tavalla, joka estää terveyshaitat ja suojelee luontoa. Lisätietoja
paikoista, joihin hävitettävät laitteet voi toimittaa kierrätettäväksi, saa ottamalla yhteyttä jätehuoltoon tai
liikkeeseen, josta tuote on ostettu.
Élimination des appareils mis au rebut par les ménages dans l'Union européenne
Le symbole apposé sur ce produit ou sur son emballage indique que ce produit ne doit pas être jeté avec
les déchets ménagers ordinaires. Il est de votre responsabilité de mettre au rebut vos appareils en les
déposant dans les centres de collecte publique désignés pour le recyclage des équipements électriques
et électroniques. La collecte et le recyclage de vos appareils mis au rebut indépendamment du reste
des déchets contribue à la préservation des ressources naturelles et garantit que ces appareils seront
recyclés dans le respect de la santé humaine et de l'environnement. Pour obtenir plus d'informations
sur les centres de collecte et de recyclage des appareils mis au rebut, veuillez contacter les autorités
locales de votre région, les services de collecte des ordures ménagères ou le magasin dans lequel vous
avez acheté ce produit.
Entsorgung von Altgeräten aus privaten Haushalten in der EU
Das Symbol auf dem Produkt oder seiner Verpackung weist darauf hin, dass das Produkt nicht über den
normalen Hausmüll entsorgt werden darf. Benutzer sind verpflichtet, die Altgeräte an einer Rücknahmestelle für Elektro- und Elektronik-Altgeräte abzugeben. Die getrennte Sammlung und ordnungsgemäße Entsorgung Ihrer Altgeräte trägt zur Erhaltung der natürlichen Ressourcen bei und garantiert
eine Wiederverwertung, die die Gesundheit des Menschen und die Umwelt schützt. Informationen dazu,
wo Sie Rücknahmestellen für Ihre Altgeräte finden, erhalten Sie bei Ihrer Stadtverwaltung, den örtlichen
Müllentsorgungsbetrieben oder im Geschäft, in dem Sie das Gerät erworben haben
Απόρριψη άχρηστου εξοπλισμού από χρήστες σε ιδιωτικά νοικοκυριά στην Ευρωπαϊκή
Ένωση
Το σύμβολο αυτό στο προϊόν ή τη συσκευασία του υποδεικνύει ότι το συγκεκριμένο προϊόν δεν
πρέπει να διατίθεται μαζί με τα άλλα οικιακά σας απορρίμματα. Αντίθετα, είναι δική σας ευθύνη να
απορρίψετε τον άχρηστο εξοπλισμό σας παραδίδοντάς τον σε καθορισμένο σημείο συλλογής για την
ανακύκλωση άχρηστου ηλεκτρικού και ηλεκτρονικού εξοπλισμού. Η ξεχωριστή συλλογή και
ανακύκλωση του άχρηστου εξοπλισμού σας κατά την απόρριψη θα συμβάλει στη διατήρηση των
φυσικών πόρων και θα διασφαλίσει ότι η ανακύκλωση γίνεται με τρόπο που προστατεύει την
ανθρώπινη υγεία και το περιβάλλον. Για περισσότερες πληροφορίες σχετικά με το πού μπορείτε να
παραδώσετε τον άχρηστο εξοπλισμό σας για ανακύκλωση, επικοινωνήστε με το αρμόδιο τοπικό
γραφείο, την τοπική υπηρεσία διάθεσης οικιακών απορριμμάτων ή το κατάστημα όπου αγοράσατε το
προϊόν.
Készülékek magánháztartásban történő selejtezése az Európai Unió területén
A készüléken, illetve a készülék csomagolásán látható azonos szimbólum annak jelzésére szolgál,
hogy a készülék a selejtezés során az egyéb háztartási hulladéktól eltérő módon kezelendő. A
vásárló a hulladékká vált készüléket köteles a kijelölt gyűjtőhelyre szállítani az elektromos és
elektronikai készülékek újrahasznosítása céljából. A hulladékká vált készülékek selejtezéskori
begyűjtése és újrahasznosítása hozzájárul a természeti erőforrások megőrzéséhez, valamint
biztosítja a selejtezett termékek környezetre és emberi egészségre nézve biztonságos feldolgozását.
A begyűjtés pontos helyéről bővebb tájékoztatást a lakhelye szerint illetékes önkormányzattól, az
illetékes szemételtakarító vállalattól, illetve a terméket elárusító helyen kaphat.
D-2
Recycle Statements
Waste Electrical and Electronic Equipment (WEEE) Statements
Nolietotu iekārtu iznīcināšanas noteikumi lietotājiem Eiropas Savienības privātajās
mājsaimniecībās
Šāds simbols uz izstrādājuma vai uz tā iesaiņojuma norāda, ka šo izstrādājumu nedrīkst izmest kopā ar
citiem sadzīves atkritumiem. Jūs atbildat par to, lai nolietotās iekārtas tiktu nodotas speciāli iekārtotos
punktos, kas paredzēti izmantoto elektrisko un elektronisko iekārtu savākšanai otrreizējai pārstrādei.
Atsevišķa nolietoto iekārtu savākšana un otrreizējā pārstrāde palīdzēs saglabāt dabas resursus un
garantēs, ka šīs iekārtas tiks otrreizēji pārstrādātas tādā veidā, lai pasargātu vidi un cilvēku veselību.
Lai uzzinātu, kur nolietotās iekārtas var izmest otrreizējai pārstrādei, jāvēršas savas dzīves vietas
pašvaldībā, sadzīves atkritumu savākšanas dienestā vai veikalā, kurā izstrādājums tika nopirkts.
Vartotojų iš privačių namų ūkių įrangos atliekų šalinimas Europos Sąjungoje
Šis simbolis ant gaminio arba jo pakuotės rodo, kad šio gaminio šalinti kartu su kitomis namų ūkio
atliekomis negalima. Šalintinas įrangos atliekas privalote pristatyti į specialią surinkimo vietą elektros ir
elektroninės įrangos atliekoms perdirbti. Atskirai surenkamos ir perdirbamos šalintinos įrangos atliekos
padės saugoti gamtinius išteklius ir užtikrinti, kad jos bus perdirbtos tokiu būdu, kuris nekenkia žmonių
sveikatai ir aplinkai. Jeigu norite sužinoti daugiau apie tai, kur galima pristatyti perdirbtinas įrangos
atliekas, kreipkitės į savo seniūniją, namų ūkio atliekų šalinimo tarnybą arba parduotuvę, kurioje
įsigijote gaminį.
Verwijdering van afgedankte apparatuur door privé-gebruikers in de Europese Unie
Dit symbool op het product of de verpakking geeft aan dat dit product niet mag worden gedeponeerd bij
het normale huishoudelijke afval. U bent zelf verantwoordelijk voor het inleveren van uw afgedankte
apparatuur bij een inzamelingspunt voor het recyclen van oude elektrische en elektronische apparatuur.
Door uw oude apparatuur apart aan te bieden en te recyclen, kunnen natuurlijke bronnen worden
behouden en kan het materiaal worden hergebruikt op een manier waarmee de volksgezondheid en het
milieu worden beschermd. Neem contact op met uw gemeente, het afvalinzamelingsbedrijf of de winkel
waar u het product hebt gekocht voor meer informatie over inzamelingspunten waar u oude apparatuur
kunt aanbieden voor recycling.
Pozbywanie się zużytego sprzętu przez użytkowników w prywatnych gospodarstwach
domowych w Unii Europejskiej
Ten symbol na produkcie lub jego opakowaniu oznacza, że produktu nie wolno wyrzucać do zwykłych
pojemników na śmieci. Obowiązkiem użytkownika jest przekazanie zużytego sprzętu do
wyznaczonego punktu zbiórki w celu recyklingu odpadów powstałych ze sprzętu elektrycznego i
elektronicznego. Osobna zbiórka oraz recykling zużytego sprzętu pomogą w ochronie zasobów
naturalnych i zapewnią ponowne wprowadzenie go do obiegu w sposób chroniący zdrowie człowieka
i środowisko. Aby uzyskać więcej informacji o tym, gdzie można przekazać zużyty sprzęt do
recyklingu, należy się skontaktować z urzędem miasta, zakładem gospodarki odpadami lub sklepem,
w którym zakupiono produkt.
D-3
Recycle Statements
Smaltimento delle apparecchiature da parte di privati nel territorio dell'Unione Europea
Questo simbolo presente sul prodotto o sulla sua confezione indica che il prodotto non può essere
smaltito insieme ai rifiuti domestici. È responsabilità dell'utente smaltire le apparecchiature consegnandole presso un punto di raccolta designato al riciclo e allo smaltimento di apparecchiature elettriche ed
elettroniche. La raccolta differenziata e il corretto riciclo delle apparecchiature da smaltire permette di
proteggere la salute degli individui e l'ecosistema. Per ulteriori informazioni relative ai punti di raccolta
delle apparecchiature, contattare l'ente locale per lo smaltimento dei rifiuti, oppure il negozio presso il
quale è stato acquistato il prodotto.
Recycle Statements
Waste Electrical and Electronic Equipment (WEEE) Statements
Recycle Statements
Descarte de Lixo Elétrico na Comunidade Européia
Este símbolo encontrado no produto ou na embalagem indica que o produto não deve ser descartado
no lixo doméstico comum. É responsabilidade do cliente descartar o material usado (lixo elétrico),
encaminhando-o para um ponto de coleta para reciclagem. A coleta e a reciclagem seletivas desse
tipo de lixo ajudarão a conservar as reservas naturais; sendo assim, a reciclagem será feita de uma
forma segura, protegendo o ambiente e a saúde das pessoas. Para obter mais informações sobre locais
que reciclam esse tipo de material, entre em contato com o escritório da HP em sua cidade, com o serviço
de coleta de lixo ou com a loja em que o produto foi adquirido.
Likvidácia vyradených zariadení v domácnostiach v Európskej únii
Symbol na výrobku alebo jeho balení označuje, že daný výrobok sa nesmie likvidovať s domovým
odpadom. Povinnosťou spotrebiteľa je odovzdať vyradené zariadenie v zbernom mieste, ktoré je
určené na recykláciu vyradených elektrických a elektronických zariadení. Separovaný zber a
recyklácia vyradených zariadení prispieva k ochrane prírodných zdrojov a zabezpečuje, že recyklácia
sa vykonáva spôsobom chrániacim ľudské zdravie a životné prostredie. Informácie o zberných
miestach na recykláciu vyradených zariadení vám poskytne miestne zastupiteľstvo, spoločnosť
zabezpečujúca odvoz domového odpadu alebo obchod, v ktorom ste si výrobok zakúpili.
Odstranjevanje odslužene opreme uporabnikov v zasebnih gospodinjstvih v Evropski uniji
Ta znak na izdelku ali njegovi embalaži pomeni, da izdelka ne smete odvreči med gospodinjske
odpadke. Nasprotno, odsluženo opremo morate predati na zbirališče, pooblaščeno za recikliranje
odslužene električne in elektronske opreme. Ločeno zbiranje in recikliranje odslužene opreme
prispeva k ohranjanju naravnih virov in zagotavlja recikliranje te opreme na zdravju in okolju neškodljiv
način. Za podrobnejše informacije o tem, kam lahko odpeljete odsluženo opremo na recikliranje, se
obrnite na pristojni organ, komunalno službo ali trgovino, kjer ste izdelek kupili.
Eliminación de residuos de equipos eléctricos y electrónicos por parte de usuarios particulares en la
Unión Europea
Este símbolo en el producto o en su envase indica que no debe eliminarse junto con los desperdicios
generales de la casa. Es responsabilidad del usuario eliminar los residuos de este tipo depositándolos
en un "punto limpio" para el reciclado de residuos eléctricos y electrónicos. La recogida y el reciclado
selectivos de los residuos de aparatos eléctricos en el momento de su eliminación contribuirá a
conservar los recursos naturales y a garantizar el reciclado de estos residuos de forma que se proteja
el medio ambiente y la salud. Para obtener más información sobre los puntos de recogida de residuos
eléctricos y electrónicos para reciclado, póngase en contacto con su ayuntamiento, con el servicio de
eliminación de residuos domésticos o con el establecimiento en el que adquirió el producto.
Bortskaffande av avfallsprodukter från användare i privathushåll inom Europeiska Unionen
Om den här symbolen visas på produkten eller förpackningen betyder det att produkten inte får
slängas på samma ställe som hushållssopor. I stället är det ditt ansvar att bortskaffa avfallet genom att
överlämna det till ett uppsamlingsställe avsett för återvinning av avfall från elektriska och elektroniska
produkter. Separat insamling och återvinning av avfallet hjälper till att spara på våra naturresurser och
gör att avfallet återvinns på ett sätt som skyddar människors hälsa och miljön. Kontakta ditt lokala
kommunkontor, din närmsta återvinningsstation för hushållsavfall eller affären där du köpte produkten
för att få mer information om var du kan lämna ditt avfall för återvinning.
D-4
Index
Numerics
10/100Base-TX ports
location on switch … 1-4
1000Base-BX … B-3
fiber-optic cable specifications … B-3
1000Base-LH … B-3
fiber-optic cable specifications … B-3
1000Base-T
1000Base-T
fiber-optic cable specifications … B-3
A
B
back of switch
description … 1-11
power connector … 1-11
basic switch configuration
IP address … 3-3
manager password … 3-2
subnet mask … 3-3
switch setup screen … 3-2
basic troubleshooting tips … 5-1
battery
replacing battery … 4-3
Bootp
automatic switch configuration … 3-2
for in-band access … 2-19
buttons
Clear button … 1-10
port LED view select button … 1-8
Reset button … 1-9
C
cabinet
mounting the switch in … 2-10
Index – 1
Index
AC power connector
location on back of switch … 1-11
Act LED … 1-7, 1-9
auto MDI/MDI-X operation … B-7, B-9
HP Auto-MDIX feature … B-6
cables
connecting cables to switch ports … 2-18
effects of non-standard cables … 5-2
fiber-optic, specifications … B-3
infrastructure requirements … 2-5
serial, for direct console connection … 2-20
cables, twisted pair
category 3, 4, 5 … B-6
cross-over cable pin-out … B-8
MDI-X to MDI connections … B-7, B-9
MDI-X to MDI-X connections … B-8
pin-outs … B-7, B-9
straight-through cable pin-out … B-7, B-9
switch-to-computer connection … B-7, B-9
switch-to-switch or hub connection … B-8
cables, twisted-pair
HP Auto-MDIX feature … B-6
wiring rules … B-6
cables, twisted-pair connector pin-outs … B-6
cabling infrastructure … 2-5
Clear button
deleting passwords … 1-10
description … 1-10
location on switch … 1-4, 1-10
restoring factory default configuration … 1-9–
1-10, 5-11
to delete password protection … 3-4
CLI command savepower … 1-8
CLI prompt, console
displaying … 2-21
configuration
checking when troubleshooting … 5-3
DHCP/Bootp … 3-2
full duplex only for mini-GBICs … 2-15
IP address … 3-3
IP address, manually … 3-2
manager password … 3-2
restoring factory defaults … 1-9–1-10, 5-11
subnet mask … 3-3
switch setup screen … 3-2
connecting the switch to a power source … 2-14
Index
console
checking messages during
troubleshooting … 5-9
displaying the CLI prompt … 2-21
features … 2-19
how to connect in-band … 2-19
how to connect out-of-band … 2-19
serial cable connection … 2-20
switch setup screen … 3-2
telnet access … 3-5
terminal configuration … 2-19
console port
definition … 1-10
location on switch … 1-4
cross-over cable
pin-out … B-8
D
deleting passwords … 1-10
description
back of switch … 1-11
front of switch … 1-4
LEDs … 1-6
switch … 1-1
desktop switch
sample topology … 2-23
DHCP
automatic switch configuration … 3-2
for in-band access … 2-19
diagnostic tests … 5-9
checking the console messages … 5-9
checking the LEDs … 5-9
end-to-end connectivity … 5-10
testing the switch only … 5-9
testing twisted-pair cabling … 5-10
downloading new switch software … 5-12
dual-personality ports
location on switch … 1-5
operation description … 1-5
E
electrical specifications, switch … A-1
EMC regulatory statements … C-8
environmental specifications, switch … A-1
F
factory default configuration, restoring … 1-9–1-10,
5-11
fan LED … 1-6
Fan Status LED … 1-6
fan Status LED … 1-6
fans
replacing fan trays … 4-1
Fault LED
behavior during self test … 2-7
location on switch … 1-4
showing error conditions … 5-4
fault LED … 1-6
behaviors … 1-6
flashing definition … 1-8
FDx LED … 1-7, 1-9
features
console … 2-19
switch … 1-11
fiber-optic cables … B-3
1000Base-BX … B-3
1000Base-LH … B-3
1000Base-T … B-3
flashing LEDs
error indications … 5-4
front of switch … 1-4
10/100Base-TX ports … 1-4
Clear button … 1-10
description … 1-4
dual-personality ports … 1-5
LEDs … 1-6
network ports … 1-5
port LED view select button and LEDs … 1-8
Reset button … 1-9
full-duplex fixed configuration
effects on network connections … 5-1
full-duplex operation of mini-GBICs … 2-15
H
hot swapping … 4-1
HP Auto-MDIX
feature description … B-6
I
in-band … 3-1
2 – Index
in-band console access
types of … 2-19
included parts … 2-1
installation
connecting the switch to a power source … 2-14
location considerations … 2-5
network cable requirements … 2-5
precautions … 2-3
rack or cabinet mounting … 2-10
site preparation … 2-5
summary of steps … 2-4
IP address
configuring … 3-3
L
MDI-X to MDI network cable … B-7, B-9
MDI-X to MDI-X network cable … B-8
mini-GBICs
full-duplex operation … 2-15
slot, location on switch … 1-4
mode conditioning patch cord … B-4
mounting the switch
in a rack or cabinet … 2-10
precautions … 2-3
N
network cables
fiber-optic, specifications … B-3
HP Auto-MDIX feature … B-6
required types … 2-5
twisted-pair connector pin-outs … B-6
twisted-pair, wiring rules … B-6
network devices
connecting to the switch … 2-18
network ports
connecting to … 2-18
location on switch … 1-5
types of … 1-5
non-standard network cables, effects … 5-2
O
out-of-band console access … 3-5
P
parts, included with the switch … 2-1
password
configuring … 3-2
passwords
deleting with the Clear button … 3-4
if you lose the password … 3-4
passwords, deleting … 1-10
physical specifications, switch … A-1
Ping test … 5-10
pin-outs
twisted-pair cables … B-6
port configuration
checking when troubleshooting … 5-3
Index – 3
Index
LEDs
Act … 1-7, 1-9
behavior during self test … 2-7
checking during troubleshooting … 5-9
descriptions of … 1-6
error indications … 5-4
Fan Status … 1-6
fan status … 1-6
Fault
behavior during self test … 2-7
showing error conditions … 5-4
fault … 1-6
FDx … 1-7, 1-9
flashing definition … 1-8
Link … 1-7
location on switch … 1-4
on switch … 1-6
port
description … 1-7
Port LED View select indicators … 1-7
Port View
selecting the display … 1-8
Power … 1-6
behavior during self test … 2-7
Self Test … 1-7
behavior during self test … 2-7
Spd … 1-7, 1-9
Usr … 1-7
Usr Mode … 1-9
Link LEDs … 1-7
link test … 5-10
location for the switch, considerations … 2-5
M
Index
Port LED View
indicator LEDs … 1-8
select button … 1-8
selecting the display … 1-8
port LEDs
description … 1-7
Link … 1-7
normal operation … 2-7
ports
10/100Base-TX, location on switch … 1-4
connecting to … 2-18
console … 2-19
HP Auto-MDIX feature … B-6
network connections … 2-18
power connector … 1-11
Power LED … 1-6
behavior during self test … 2-7
behaviors … 1-6
location on switch … 1-4
power source
connecting the switch to … 2-14
power supply
replacing … 4-5
precautions
mounting the switch … 2-3
power requirements … 2-3
preparing the installation site … 2-5
Proactive Network tools
diagnostics with … 5-8
R
rack
mounting precautions … 2-3
mounting the switch in … 2-10
ranges
voltage … 1-11, 2-6
recycle statements … D-1
regulatory statements … C-8
replacing components
battery … 4-3
power supply … 4-5
replacing hardware
fans … 4-1
Reset button
description … 1-9
location on switch … 1-4, 1-9
restoring factory default configuration … 5-11
4 – Index
resetting the switch
factory default reset … 5-11
location of Reset button … 1-9
troubleshooting procedure … 5-9
reversing air flow
default air flow … 2-8
S
safety and regulatory statements … C-1
safety specifications … A-2
savepower CLI command … 1-8
selecting the Port LED View display … 1-8
self test
Fault LED behavior … 2-7
LED behavior during … 2-7
Power LED behavior … 2-7
Self Test LED … 1-7
behavior during factory default reset … 5-11
serial cable
for direct console connection … 2-20
slots for mini-GBICs
location on switch … 1-4
Spd LED … 1-9
Spd LEDs … 1-7
specifications
cabling … B-1
distance … B-3
electrical … A-1
environmental … A-1
physical … A-1
safety … A-2
straight-through cable
pin-out … B-7, B-9
subnet mask
configuring … 3-3
summary
of switch installation … 2-4
T
technology distance specifications … B-3
telnet access to the console … 3-5
terminal configuration … 2-19
Test LED
behavior during self test … 2-7
testing
checking the console messages … 5-9
checking the LEDs … 5-9
diagnostic tests … 5-9
end-to-end communications … 5-10
link test … 5-10
Ping test … 5-10
switch operation … 5-9
switch-to-device communications … 5-10
twisted-pair cabling … 5-10
tips for troubleshooting … 5-1
topologies
effects of improper topology … 5-2
samples of … 2-22
troubleshooting … 5-1
basic tips … 5-1
checking port configuration … 5-3
checking the console messages … 5-9
checking the LEDs … 5-9
common network problems … 5-1
connecting to fixed full-duplex devices … 5-1
diagnostic tests … 5-9
effects of improper topology … 5-2
effects of non-standard cables … 5-2
link test … 5-10
Ping test … 5-10
Proactive Network tools … 5-8
restoring factory default configuration … 5-11
testing connections to other devices … 5-10
testing end-to-end communications … 5-10
testing the switch … 5-9
testing the twisted-pair cables … 5-10
twisted-pair cable
cross-over cable pin-out … B-8
pin-outs … B-6–B-7, B-9
straight-through cable pin-out … B-7, B-9
switch-to-computer connection … B-7, B-9
switch-to-switch or hub connection … B-8
testing … 5-10
twisted-pair ports
HP Auto-MDIX feature … B-6
U
Usr LEDs … 1-7
Usr Mode LED … 1-9
V
voltage ranges … 1-11, 2-6
VT-100 terminal
serial cable connection for … 2-20
W
wiring rules for twisted-pair cables … B-6
Index – 5
Index
switch
connecting to a power source … 2-14
description … 1-1
downloading new software … 5-12
electrical specifications … A-1
environmental specifications … A-1
features … 1-11
front panel description … 1-4
included parts … 2-1
LED descriptions … 1-6
mounting in a rack or cabinet … 2-10
physical specifications … A-1
switch operation
verifying after installation … 2-5
Switch Setup screen
configuring a subnet mask … 3-3
configuring an IP address … 3-3
field descriptions … 3-3
switch setup screen … 3-2
© Copyright 2009 Hewlett-Packard
Development Company, L.P.
January 2009
Manual Part Number
5992-4962
*5992-4962*