QUICK START GUIDE LI2208 LINEAR IMAGER

LI2208 LINEAR IMAGER
QUICK START GUIDE
SET DEFAULTS / ENTER KEY BAR CODES
SET DEFAULTS
TAB KEY BAR CODE
ADD A TAB KEY
To add a Tab key after scanned data, scan
the bar code below.
http://www.motorolasolutions.com/LI2208 See Product Reference Guide
for detailed information
RETURN TO FACTORY DEFAULTS
ADD A TAB KEY
ADD AN ENTER KEY
(Carriage Return/Line Feed)
POST IN WORK AREA
To add an Enter key after scanned data, scan
the bar code below.
ADD AN ENTER KEY (CARRIAGE RETURN/LINE FEED)
SCANNER FEATURES
PRESENTATION MODE
1
USB CAPS LOCK OVERRIDE BAR CODE
USB - OVERRIDE CAPS LOCK KEY (ENABLE)
3
2
4
*USB - DO NOT OVERRIDE CAPS LOCK KEY (DISABLE)
1 Scan Window
2 Scan Trigger
3 LED
4 Beeper
STEP 1 - CONNECT HOST INTERFACE
STEP 2 - SET UP INTERFACE (Scan Host Bar Codes)
USB
USB
Scan ONE of the bar codes below
NOTE: Cables may vary depending on configuration
The interface cable automatically detects the host interface type and uses the
default setting. If the default (*) does not meet your requirements, scan another
host bar code below.
*USB KEYBOARD (HID)
IBM OPOS (IBM HAND-HELD USB with FULL SCAN ENABLE)
USB CDC Host
SIMPLE COM PORT EMULATION
IBM TABLE TOP USB
IBM HAND-HELD USB
SNAPI WITHOUT IMAGING
RS-232
TOSHIBA TEC Host
RS-232
Scan ONE of the bar codes below
The interface cable automatically detects the host interface type and uses the
default setting. If the default (*) does not meet your requirements, scan another
host bar code below.
NIXDORF RS-232 MODE B
*STANDARD RS-232
ICL RS-232
FUJITSU RS-232
OPOS/JPOS
NIXDORF RS-232 MODE A
Keyboard Wedge
Keyboard Wedge
Scan a bar code below
The Auto-Host Detect Cable feature automatically detects the host interface type
and uses the default setting. If the default (*) does not meet your requirements,
scan the IBM PC/AT and IBM PC COMPATIBLE bar code below.
*IBM AT NOTEBOOK
IBM PC/AT and IBM PC COMPATIBLE
IBM 46XX
IBM 46XX
Scan ONE of the bar codes below
The Auto-Host Detect Cable feature automatically detects the host interface type,
but there is no default setting. Scan one of the bar codes below to select the
appropriate port.
NON-IBM SCANNER EMULATION (PORT 5B)
TABLE-TOP SCANNER EMULATION (PORT 17)
HAND-HELD SCANNER EMULATION (PORT 9B)
123Scan
ABOUT 123Scan2
123Scan2 is an easy-to-use, PC-based software tool
that enables rapid and easy customized setup of
a scanner via a bar code or USB cable.
For more information,
visit: http://www.motorolasolutions.com/123Scan.
2
UTILITY FUNCTIONALITY
- Device Configuration
- Electronic Programming (USB Cable)
- Programming Bar Code(s)
- Data View – Scan Log (Display Scanned Bar Code Data)
- Access Asset Tracking Information
- Upgrade Firmware and View Release Notes
- Remote Management (SMS Package Generation)
LI2208 LINEAR IMAGER
SCANNING
POST IN
WORK AREA
Aiming
012345
012345
RECOMMENDED USAGE GUIDE - OPTIMUM BODY POSTURE
Avoid Extreme Wrist Angles
Avoid Bending
Avoid Reaching
AVOID BENDING
AVOID REACHING
AVOID EXTREME
WRIST ANGLES
BEEPER INDICATIONS
Indication
LED INDICATIONS
Hand-Held Scanning
Beeper Sequence
Indication
LED Indicator
Power up
Low/medium/high beep
Bar code decoded
Short high beep
Transmission error detected; data is ignored
4 long low beeps
Successful parameter setting
High/low/high/low beep
Correct programming sequence performed
High/low beep
No power to scanner
Off
Incorrect programming sequence, or Cancel
bar code scanned
Low/high beep
Scanner is ready to scan
Green
Bar code is successfully decoded
Off Momentarily
Transmission error
Red
Scanner is on and ready to scan, or no power to scanner
Off
Bar code is successfully decoded
Green
Transmission error
Red
Hands-Free (Presentation) Scanning
Local Contact:
TROUBLESHOOTING
Scanner not working
Scanner not decoding bar code
No power to scanner
Check system power.
Scanner not programmed for bar code type
Scanner is disabled
Ensure that correct host
interface cable is used.
Bar code unreadable
Scanner decoding bar code, but data not transmitting to host
Distance between scanner and bar code incorrect
Ensure scanner is programmed to read
type of bar code being scanned.
Ensure bar code is not defaced; try scanning test bar code of same bar code type.
Move scanner closer to, or further
from bar code.
Host interface not configured properly
Scan appropriate host
parameter bar codes
Scanned data incorrectly displayed on host
Interface cable is loose
Ensure all cable connections
are secure
Host interface not configured properly
Scan appropriate host parameter bar codes.
REGULATORY INFORMATION
© 2013 MOTOROLA SOLUTIONS, Inc. All rights reserved.
Motorola reserves the right to make changes to any product to improve reliability, function, or design.
Motorola does not assume any product liability arising out of, or in connection with, the application or use of any
product, circuit, or application described herein. No license is granted, either expressly or by implication,
estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system,
apparatus, machine, material, method, or process in which Motorola products might be used. An implied license
exists only for equipment, circuits, and subsystems contained in Motorola products.
This device is approved under the Symbol Technologies, Inc. brand: Symbol Technologies, Inc. is a
wholly owned subsidiary of Motorola Solutions, Inc. (collectively “Motorola”). This guide applies to
Model Number: LI2208. All Motorola devices are designed to be compliant with rules and
regulations in locations they are sold and will be labeled as required. Local language translations are
available at the following website: http://www.motorolasolutions.com/support.
Any changes or modifications to Motorola equipment, not expressly approved by
Motorola, could void the user’s authority to operate the equipment.
Power Supply
Use ONLY a Motorola approved UL LISTED ITE (IEC/EN 60950-1, SELV) power supply with electrical ratings:
Output 5Vdc, min 850mA, with a maximum ambient temperature of at least 40 degrees C. Use of alternative
power supply will invalidate any approvals given to this unit and may be dangerous.
Warranty
For the complete Motorola Solutions hardware product warranty statement, go to:
http://www.motorola.com/enterprisemobility/warranty.
For Australia Only
This warranty is given by Motorola Solutions Australia Pty Limited (ABN16 004 742 312) of Tally Ho Business Park,
10 Wesley Court. Burwood East, Victoria. Our goods come with guarantees that cannot be excluded under the
Australia Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any
other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a major failure. Motorola Solutions
Australia’s limited warranty above is in addition to any rights and remedies you may have under the Australian
Consumer Law. If you have any queries, please call Motorola Solutions Australia at 1800457 439. You may also visit
our website: http://www.motorola.com/Business/XA-EN/Pages/Contact_Us for the most updated warranty terms.
Service Information
If you have a problem using the equipment, contact your facility’s Technical or Systems Support. If there is a
problem with the equipment, they will contact the Motorola Solutions Global Customer Support Center at:
http://www.motorolasolutions.com/support.
For the latest version of this guide go to: http://www.motorolasolutions.com/support.
Waste Electrical and Electronic Equipment (WEEE)
Bulgarish: За клиенти от ЕС: След края на полезния им живот всички продукти трябва да се връщ
ат на Motorola за рециклиране. За информация относно връщането на продукти, моля отидете на
адрес: http://www.motorolasolutions.com/recycling/weee.
Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skončení jejich životnosti vrátit společnosti
Motorola k recyklaci. Informace o způsobu vrácení produktu najdete na webové stránce:
http://www.motorolasolutions.com/recycling/weee.
Dansk: Til kunder i EU: Alle produkter skal returneres til Motorola til recirkulering, når de er udtjent. Læs
oplysningerne om returnering af produkter på: http://www.motorolasolutions.com/recycling/weee.
Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer Lebensdauer zum
Recycling an Motorola zurückgesandt werden. Informationen zur Rücksendung von Produkten finden
Sie unter http://www.motorolasolutions.com/recycling/weee.
Health and Safety Recommendation
Ergonomic Recommendations
Caution: In order to avoid or minimize the potential risk of ergonomic injury
follow the recommendations below. Consult with your local Health & Safety
Manager to ensure that you are adhering to your company's safety programs
to prevent employee injury.
• Reduce or eliminate repetitive motion
• Maintain a natural position
• Reduce or eliminate excessive force
• Keep objects that are used frequently within easy reach
• Perform tasks at correct heights
• Reduce or eliminate vibration
• Reduce or eliminate direct pressure
• Provide adjustable workstations
• Provide adequate clearance
• Provide a suitable working environment
• Improve work procedures.
Class 1 LED Safety
COMPLIES WITH IEC 60825-1:2001 (Ed.1.2) & IEC 62471:2006 (Ed.1.0);EN 62471:2008
Radio Frequency Interference Requirements -FCC
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
FOR HOME OR OFFICE USE
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Tested to comply
with FCC Standards
•
•
•
•
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
Consult the dealer or an experienced radio/TV technician for help.
Radio Frequency Interference Requirements - Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Marking and European Economic Area (EEA)
Statement of Compliance
Motorola hereby declares that this device is in compliance with all the applicable
Directives, 2004/108/EC and 2006/95/EC. A Declaration of Conformity may be obtained
from http://www.motorolasolutions.com/doc
Other Countries
Japan (VCCI) - Voluntary Control Council for Interference
Class B ITE
CLASS 1 LED PRODUCT
LED KLASSE 1
APPAREIL À LED DE CLASSE 1
B
Korea Warning Statement for Class B ITE
Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας ζωής τους, πρέπει να επιστρ
έφονται στην Motorola για ανακύκλωση. Για περισσότερες πληροφορίες σχετικά με την επιστροφή ενός
προϊόντος, επισκεφθείτε τη διεύθυνση http://www.motorolasolutions.com/recycling/weee στο Διαδίκτυο.
English: For EU Customers: All products at the end of their life must be returned to Motorola for
recycling. For information on how to return product, please go to:
http://www.motorolasolutions.com/recycling/weee.
Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a Motorola al final
de su ciclo de vida para que sean reciclados. Si desea más información sobre cómo devolver un
producto, visite: http://www.motorolasolutions.com/recycling/weee.
Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada taaskasutamise eesmärgil
Motorola'ile. Lisainformatsiooni saamiseks toote tagastamise kohta külastage palun aadressi:
http://www.motorolasolutions.com/recycling/weee.
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrätettäväksi
Motorola-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen palauttamisesta on osoitteessa
http://www.motorolasolutions.com/recycling/weee.
Français : Clients de l'Union Européenne : Tous les produits en fin de cycle de vie doivent être
retournés à Motorola pour recyclage. Pour de plus amples informations sur le retour de produits,
consultez : http://www.motorolasolutions.com/recycling/weee.
Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Motorola vállalathoz kell eljuttatni
újrahasznosítás céljából. A termék visszajuttatásának módjával kapcsolatos tudnivalókért látogasson el
a http://www.motorolasolutions.com/recycling/weee.
Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono
essere restituiti a Motorola al fine di consentirne il riciclaggio. Per informazioni sulle modalità di
restituzione, visitare il seguente sito Web: http://www.motorolasolutions.com/recycling/weee.
Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi būti grąžinti utilizuoti į
kompaniją „Motorola“. Daugiau informacijos, kaip grąžinti gaminį, rasite:
http://www.motorolasolutions.com/recycling/weee.
Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir jānogādā atpakaļ Motorola
otrreizējai pārstrādei. Lai iegūtu informāciju par produktu nogādāšanu Motorola, lūdzu, skatiet:
http://www.motorolasolutions.com/recycling/weee.
Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu tagħhom, iridu jiġu
rritornati għand Motorola għar-riċiklaġġ. Għal aktar tagħrif dwar kif għandek tirritorna l-prodott, jekk
jogħġbok żur: http://www.motorolasolutions.com/recycling/weee.
Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar
Motorola te worden teruggezonden voor recycling. Raadpleeg
http://www.motorolasolutions.com/recycling/weee voor meer informatie over het terugzenden van
producten.
http://www.motorolasolutions.com/recycling/weee.
Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos à Motorola
para reciclagem. Para obter informações sobre como devolver o produto, visite:
http://www.motorolasolutions.com/recycling/weee.
Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor de funcţionare, trebuie
returnate la Motorola pentru reciclare. Pentru informaţii despre returnarea produsului,
accesaţi: http://www.motorolasolutions.com/recycling/weee.
Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po uplynutí doby ich životnosti
vrátené spoločnosti Motorola na recykláciu. Bližšie informácie o vrátení výrobkov nájdete na:
http://www.motorolasolutions.com/recycling/weee
Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju Motorola za
reciklažo. Za informacije o vračilu izdelka obiščite:http://www.motorolasolutions.com/recycling/weee.
Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras till Motorola
för återvinning. Information om hur du returnerar produkten finns på
http://www.motorolasolutions.com/recycling/weee.
Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme için Motorola'ya iade
edilmelidir. Ürünlerin nasıl iade edileceği hakkında bilgi için lütfen şu adresi ziyaret edin:
http://www.motorolasolutions.com/recycle/weee.
TURKISH WEEE Statement of Compliance
EEE Yönetmeliğine Uygundur
Motorola Solutions, Inc.
One Motorola Plaza Holtsville, New York 11742-1300, USA
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are
trademarks or registered trademarks of Motorola Trademark Holdings, LLC
and are used under license. All other trademarks are the property of their
respective owners.
© 2013 Motorola Solutions, Inc. All rights reserved.
72-170536-01 Revision A June 2013
LI2208 LINEAR IMAGER
LED Output
This device contains two LEDs for illumination and aiming.
Ukraine
Aim/Illumination:
Optical Output: 0.87mW
Pulse Duration: Continuous
Emitted Wavelength: 590-650nm
Дане обладнання відповідає вимогам технічного регламенту №1057, № 2008 на обмеження щодо
використання деяких небезпечних речовин в електричних та електронних пристроях.
Viewing the LED output with certain optical instruments (for example, eye loupes,
magnifiers and microscopes) may pose an eye hazard.
Caution: Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous LED light exposure.
China RoHS
http://www.motorola.com/ds6878
This table was created to comply with China RoHS requirements.
50
有毒有害物质或元素
LED light is emitted from this aperture:
部件名称
(Parts)
•
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr6+)
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
金属部件
(Metal Parts)
X
O
O
O
O
O
电路模块
(Circuit Modules)
X
O
O
O
O
O
电缆及电缆组件
(Cables and Cable Assemblies)
O
O
O
O
O
O
塑料和聚合物部件
(Plastic and Polymeric Parts)
O
O
O
O
O
O
光学和光学组件
(Optics and Optical Components)
X
O
O
O
O
O
电池
(Batteries)
O
O
O
O
O
O
O:表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T11363-2006 标准规定的限
量要求以下。
X:表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规
定的限量要求。
对销售之日的所售产品,本表表示,公司供应链的电子信息产品可能包含这些物质。注意:在
所售产品中可能会也可能不会含有所有所列的部件。