Extreme Networks Altitude 4000 Series Installation guide

Summit® WM3700 Wireless LAN Controller
Installation Guide
For Software Version 5
Extreme Networks, Inc.
3585 Monroe Street
Santa Clara, California 95051
(888) 257-3000
(408) 579-2800
http://www.extremenetworks.com
Published: November 2011
Part number: 100355-00 Rev 02
AccessAdapt, Alpine, Altitude, BlackDiamond, Direct Attach, EPICenter, ExtremeWorks Essentials, Ethernet
Everywhere, Extreme Enabled, Extreme Ethernet Everywhere, Extreme Networks, Extreme Standby Router
Protocol, Extreme Turbodrive, Extreme Velocity, ExtremeWare, ExtremeWorks, ExtremeXOS, Go Purple Extreme
Solution, ExtremeXOS ScreenPlay, ReachNXT, Ridgeline, Sentriant, ServiceWatch, Summit, SummitStack, Triumph,
Unified Access Architecture, Unified Access RF Manager, UniStack, XNV, the Extreme Networks logo, the Alpine
logo, the BlackDiamond logo, the Extreme Turbodrive logo, the Summit logos, and the Powered by ExtremeXOS
logo are trademarks or registered trademarks of Extreme Networks, Inc. or its subsidiaries in the United States
and/or other countries.
sFlow is the property of InMon Corporation.
Specifications are subject to change without notice.
All other registered trademarks, trademarks, and service marks are property of their respective owners.
© 2011 Extreme Networks, Inc. All Rights Reserved.
Summit® WM3700 Wireless LAN Controller Installation Guide
2
Table of Contents
Chapter 1: Introduction.............................................................................................................................. 5
Package Contents ....................................................................................................................................................5
Document Conventions ............................................................................................................................................5
Warnings ..................................................................................................................................................................6
Site Preparation........................................................................................................................................................6
Chapter 2: Specifications .......................................................................................................................... 9
Physical Specifications .............................................................................................................................................9
Power Cord Specifications .......................................................................................................................................9
Power Protection ...............................................................................................................................................9
Chapter 3: LED Codes.............................................................................................................................. 11
System Status LEDs ..............................................................................................................................................11
Start Up / POST (Primary System or Redundant System)..............................................................................11
Controller Status (Primary System).................................................................................................................12
Controller Status (Redundant System)............................................................................................................12
Fan LED ..........................................................................................................................................................12
Temperature Status LED ................................................................................................................................13
RJ-45 Gigabit Ethernet LEDs .................................................................................................................................13
RJ-45 Port Speed LED....................................................................................................................................13
RJ-45 Port Status LED ....................................................................................................................................13
SFP Gigabit Ethernet LEDs....................................................................................................................................14
SFP Port Speed LED ......................................................................................................................................14
SFP Port Status LED ......................................................................................................................................14
Out of Band Management Port LEDs .....................................................................................................................15
Out of Band Management Port Speed LED ....................................................................................................15
Out of Band Management Port Status LED ....................................................................................................15
Chapter 4: Hardware Setup ..................................................................................................................... 17
Cabling Information ................................................................................................................................................17
Gigabit Ethernet on the Summit WM3700 wireless LAN controller ........................................................................18
Installing Gigabit Ethernet SFPs .....................................................................................................................19
Connecting USB Devices .......................................................................................................................................20
Installing a Compact Flash Card ............................................................................................................................21
Rack Mount Instructions .........................................................................................................................................22
Summit WM3700 wireless LAN controller Console Port Setup ..............................................................................22
Supplying Power to the Summit WM3700 wireless LAN controller ........................................................................23
Verifying the Installation .........................................................................................................................................23
Chapter 5: Basic Configuration............................................................................................................... 25
Chapter 6: Regulatory Information ......................................................................................................... 27
Laser Devices - Gigabit Ethernet SFP Option ........................................................................................................27
Country Selection ...................................................................................................................................................27
Radio Frequency Interference Requirements - FCC ..............................................................................................28
Radio Frequency Interference Requirements - Canada.........................................................................................28
Statement of Compliance .......................................................................................................................................28
Summit® WM3700 Wireless LAN Controller Installation Guide
3
Table of Contents
Chapter 7: Part Numbers and Support ................................................................................................... 31
Customer Service ...................................................................................................................................................31
Registration ............................................................................................................................................................32
Documentation .......................................................................................................................................................32
Chapter 8: Extreme Networks, Inc. End-User License Agreement ...................................................... 33
Summit® WM3700 Wireless LAN Controller Installation Guide
4
1
Introduction
CHAPTER
The Extreme Networks® Summit® WM3700 wireless LAN controller is a high-performance member of
the Extreme Networks wireless controller family. The Summit WM3700 wireless LAN controller
provides centralized wireless LAN (WLAN) configuration and management by coalescing a network
“intelligence” previously spread across physically distributed access points. The Summit WM3700
wireless LAN controller is the WLAN’s single point of contact, thus reducing wireless networking
complexity by moving management out of the ceiling and into the wiring closet. In addition, through
the use of a Virtual AP architecture, the Summit WM3700 wireless LAN controller lets you create
multiple WLANs without changing or adding to the existing wired network infrastructure.
This document is written for the network device installer.
Package Contents
Inspect the package contents and report any missing or damaged items to your sales representative. The
package should contain the following:
●
Summit WM3700 wireless LAN controller with Rack Brackets installed
●
Console Cable
●
Summit® WM3700 Wireless LAN Controller Installation Guide (this document)
●
China RoHS compliance document
Document Conventions
The following graphical alerts are used in this document to indicate notable situations:
NOTE
Tips, hints, or special requirements that you should take note of.
CAUTION
Care is required. Disregarding a caution can result in data loss or equipment malfunction.
Summit® WM3700 Wireless LAN Controller Installation Guide
5
Chapter 1: Introduction
WARNING!
Indicates a condition or procedure that could result in personal injury or equipment damage.
Warnings
●
Read all installation instructions and site survey reports, and verify correct equipment installation
before connecting the system to its power source.
●
Remove jewelry and watches before installing this equipment.
●
Install the equipment in a rack with adequate dimensions and weight allowances.
●
Verify the rack is anchored and cannot tip over or break away from its mountings.
●
Verify the unit is grounded before connecting it to the power source.
●
Verify any device connected to this unit is properly wired and grounded.
●
Connect all power cords to a properly wired and grounded electrical circuit.
●
Verify the electrical circuits have appropriate overload protection.
●
Attach only approved power cords to the device.
●
Extreme Networks strongly recommends the use of an Uninterruptible Power Supply (UPS) that
supports the Summit WM3700 wireless LAN controller power rating. Not using a UPS can result in
data loss or equipment damage due to a power surge or power failure.
●
Verify that the power connector and socket are accessible at all times during the operation of the
equipment.
●
Do not work with power circuits in dimly lit spaces.
●
Do not install this equipment or work with its power circuits during thunderstorms or other weather
conditions that could cause a power surge.
●
Verify there is adequate ventilation around the device, and ambient temperatures meet equipment
operation specifications.
Site Preparation
●
Consult your site survey and network analysis reports to determine specific equipment placement,
port capacity, power drops, and so on.
●
Assign installation responsibility to the appropriate personnel.
●
Identify where all installed components are located.
●
Verify appropriate rack mounting requirements.
●
Provide a sufficient number of power drops for your equipment.
●
Ensure adequate, dust-free ventilation to all installed equipment.
●
Identify and prepare Ethernet and console port connections.
●
Verify that cable lengths are within the maximum allowable distances for optimal signal
transmission.
Summit® WM3700 Wireless LAN Controller Installation Guide
6
Site Preparation
●
Verify that the Summit WM3700 wireless LAN controller is powered through an Uninterruptible
Power Supply (UPS).
Summit® WM3700 Wireless LAN Controller Installation Guide
7
Chapter 1: Introduction
Summit® WM3700 Wireless LAN Controller Installation Guide
8
2
Specifications
CHAPTER
Physical Specifications
Width
440mm (17.32 in)
Height
44.45mm (1.75 in)
Depth
390.8mm (15.38 in)
Weight
6.12 Kg (13.5 lbs)
Operating Temperature
0°C - 40°C
Operating Humidity
5% - 85% RH, non-condensing
Operating Altitude
3 km (10000 ft)
Power Cord Specifications
A power cord is not supplied with the controller. Use only a correctly rated power cord certified (as
appropriate) for the country of operation.
Power Protection
●
If possible, use a circuit dedicated to data processing equipment. Commercial electrical contractors
are familiar with wiring for data processing equipment and can help with the load balancing of these
circuits.
●
Install surge protection. Be sure to use a surge protection device between the electricity source and
the Summit WM3700 wireless LAN controller.
●
Install an Uninterruptible Power Supply (UPS). A UPS provides continuous power during a power
outage. Some UPS devices have integral surge protection. UPS equipment requires periodic
maintenance to ensure reliability. A UPS of the proper capacity for the data processing equipment
must be purchased.
Summit® WM3700 Wireless LAN Controller Installation Guide
9
Chapter 2: Specifications
Summit® WM3700 Wireless LAN Controller Installation Guide
10
3
LED Codes
CHAPTER
The Summit WM3700 wireless LAN controller has four vertically-stacked LEDs on its front panel. Each
of the controller’s Gigabit Ethernet ports have two status LEDs. These LEDs display two colors (green &
amber), and three lit states (solid, blinking, and off). The following tables decode the combinations of
LED colors and states for the System Status LEDs and the Gigabit Ethernet LEDs.
System Status LEDs
System Status 1
System Status 2
Fan status
Temperature status
Start Up / POST (Primary System or Redundant System)
System Status 1 LED
System Status 2 LED
Event
Off
Off
Power off
Green Blinking
Green Blinking
Power On Self Test (POST) running
Green Solid
Green Blinking
POST succeeded (Operating System
Loading)
Green Solid
Off
POST succeeded (Normal Operation)
Amber Blinking
Off
POST Failure
Alternating Green
Blinking & Amber
Blinking
Alternating Green
Blinking & Amber
Blinking
Boot Up Error: Device has an invalid
checksum
Summit® WM3700 Wireless LAN Controller Installation Guide
11
Chapter 3: LED Codes
NOTE
During controller start up, the Temperature status LED will be lit Solid Amber. This is normal behavior and
does not indicate an error. At the completion of start up the Temperature Status LED will switch to Solid Green.
Controller Status (Primary System)
System Status 1 LED
System Status 2 LED
Event
Off
Off
Power off
Green Solid
Off
No Redundancy Feature Enabled
Green Solid
Green Solid
Redundancy Feature Enabled
Actively Adopting Access Points
Green Solid
Amber Blinking
No License to adopt Access Points or No
Country Code configured on the controller.
Controller Status (Redundant System)
System Status 1 LED
System Status 2 LED
Event
Off
Off
Power off
Green Solid
Off
No Redundancy Feature Enabled
Green Blinking
Green Solid
Redundant System failed over and
adopting ports
Green Blinking
Alternating Green
Blinking & Amber
Blinking
Redundant System not failed over.
Green Solid
Amber Blinking
No License to adopt Access Points or No
Country Code configured on the controller.
Fan LED
Fan LED
Event
Off
System Off / POST Start
Green Blinking
POST in Process
Green Solid
All System Fans Normal Operation
Amber Solid
Redundant Cooling Failure
System Operational
Amber Blinking
System Cooling Failure
System will be held in reset until the issue
is resolved
Summit® WM3700 Wireless LAN Controller Installation Guide
12
RJ-45 Gigabit Ethernet LEDs
Temperature Status LED
Temperature LED
Event
Off
System Off
Green Solid
Ambient Inlet Temperature is within
specified operating limit
Amber Solid
Ambient Inlet Temperature is near the
maximum operating temperature
During controller start up this LED will be
lit Solid Amber. This is normal behavior
and does not indicate an error.
Amber Blinking
Ambient Inlet Temperature is above the
maximum specified operating temperature
System will be held in reset until the issue
is resolved
RJ-45 Gigabit Ethernet LEDs
Port
speed
Port
status
sym_006
Port
Port
speed status
RJ-45 Port Speed LED
Port Speed LED
Event
Off
10 Mbps
Green Solid
100 Mbps
Green Blinking
1000 Mbps
Amber Blinking
Port Fault
RJ-45 Port Status LED
Port Status LED
Event
Off
No Link or Administratively shut down
Summit® WM3700 Wireless LAN Controller Installation Guide
13
Chapter 3: LED Codes
Port Status LED
Event
Green Solid
Link present
Green Blinking
Activity: Transmit and Receive
Amber Blinking
Link Fault
SFP Gigabit Ethernet LEDs
Port
Port
speed status
Upper
Port
sym_
Lower
Port
SFP Port Speed LED
Port Speed LED
Event
Green Blinking
1000 Mbps
Amber Blinking
Module or Tx/Rx Fault Loss
SFP Port Status LED
Port Status LED
Event
Off
No Link or Administratively shut down
Green Solid
Link present / Operational
Amber Blinking
Module or Tx/Rx Fault Loss
Summit® WM3700 Wireless LAN Controller Installation Guide
14
Out of Band Management Port LEDs
Out of Band Management Port LEDs
Port
speed
Port
status
sym_0
Out of Band Management Port Speed LED
Port Speed LED
Event
Off
10 Mbps
Green Solid
100 Mbps
Amber Blinking
Port Fault
Out of Band Management Port Status LED
Port Status LED
Event
Off
No Link
Green Solid
Link present
Green Blinking
Activity: Transmit and Receive
Amber Blinking
Link Fault
Summit® WM3700 Wireless LAN Controller Installation Guide
15
Chapter 3: LED Codes
Summit® WM3700 Wireless LAN Controller Installation Guide
16
4
Hardware Setup
CHAPTER
Gigabit Ethernet
RJ45s
Console
connector
Gigabit Ethernet
SFPs
Compact
Flash
Out-of-band
management
port
(FE Port)
USB
ports
sym_023
Cabling Information
Console
Out-of-Band
Management
USB 1
USB 2
Compact Flash
Gigabit
SFP
Port 1
Gigabit
Ethernet
Port 1
Gigabit
SFP
Port 3
Gigabit
Ethernet
Port 3
Gigabit
SFP
Port 2
Gigabit
Ethernet
Port 2
Gigabit
SFP
Port 4
Gigabit
Ethernet
Port 4
sym_005
Summit® WM3700 Wireless LAN Controller Installation Guide
17
Chapter 4: Hardware Setup
The Summit WM3700 wireless LAN controller has four RJ-45 Gigabit Ethernet ports, four Gigabit SFP
(fiber) ports, one Out-of-band Fast Ethernet management port and one Console connector. The above
diagram shows each of those ports and the cables or devices attached to them. The sections that follow
describe detailed connection and cabling information for each port. For software configuration, please
see the Summit WM3000 Series Controller System Reference Guide available from the Extreme Networks
website at: http://www.extremenetworks.com/go/documentation.
NOTE
The management port on the Summit WM3700 wireless LAN controller does not support
MDI/MDI-X
Gigabit Ethernet on the Summit WM3700 wireless
LAN controller
Gigabit Ethernet
RJ45s
Gigabit Ethernet
SFPs
The Summit WM3700 wireless LAN controller has four RJ-45 Gigabit Ethernet ports and four Gigabit
SFP (fiber optic) ports. Using the RJ-45 ports requires connecting a Category-6 Ethernet cable to the
port. To use the Gigabit SFP ports, first install the SFP Modules.
Summit® WM3700 Wireless LAN Controller Installation Guide
18
Gigabit Ethernet on the Summit WM3700 wireless LAN controller
Installing Gigabit Ethernet SFPs
1 Open the bail on the transceiver.
Open bail to insert or remove
SFP transceiver
2 Insert each of the SFP transceivers into the corresponding ports on the controller.
3 Once the SFP transceivers are properly seated in their ports, close the bails to lock the transceivers in
place.
4 Insert the fiber optic cables into the installed transceivers
Summit® WM3700 Wireless LAN Controller Installation Guide
19
Chapter 4: Hardware Setup
.
Connecting USB Devices
USB
ports
The Summit WM3700 wireless LAN controller contains two USB ports for connecting USB flash storage
devices to the controller. The controller can use the USB flash storage devices for file transfers and
firmware updates. Follow the setup instructions below to connect the devices to the controller and then
access those devices through the Web UI or Command Line Interface.
1 Connect the USB flash drive to either of the USB ports.
2 Wait a few seconds for the drive to be recognized by the controller.
Summit® WM3700 Wireless LAN Controller Installation Guide
20
Installing a Compact Flash Card
3 Follow the instructions in the Summit WM3000 Series Controller System Reference Guide or Summit®
WM3000 Series Controller and Altitude™ 4000 Series Access Point CLI Reference Guide for more
information on accessing USB storage devices from the controller for file transfers or firmware
updates.
NOTE
The controller supports USB flash devices formatted with FAT or VFAT (FAT32) filesystems only. If your
flash storage device is formatted with another filesystem you will need to format the device before it can be used in
the system.
Installing a Compact Flash Card
Compact
Flash slot
Compact Flash
The Summit WM3700 wireless LAN controller contains a Compact Flash slot for file transfers, firmware
updates and use by Extreme Networks service technicians. Follow the setup instructions below to
connect a Compact Flash Card to the controller and then access that card through the Web UI.
1 To use a Compact Flash card with the Summit WM3700 wireless LAN controller insert the card into
the Compact Flash slot.
2 Once the Compact Flash card has been inserted, follow the instructions in the Summit WM3000 Series
Controller System Reference Guide or Summit® WM3000 Series Controller and Altitude™ 4000 Series
Access Point CLI Reference Guide to use the Compact Flash card for file transfers or firmware updates.
Summit® WM3700 Wireless LAN Controller Installation Guide
21
Chapter 4: Hardware Setup
Rack Mount Instructions
To install the Summit WM3700 wireless LAN controller in a rack:
1 The rack mounting brackets are installed at the factory. No additional steps are needed.
2 Attach the brackets to the rack using screws appropriate for your rack’s mounting holes.
Summit WM3700 wireless LAN controller Console
Port Setup
To add the Summit WM3700 wireless LAN controller to the network and prepare it for initial
configuration:
1 Using the supplied console cable (pictured below), connect the Summit WM3700 wireless LAN
controller serial port to an RS-232 (DB-9) serial port on a separate computer (the “configuration
computer”).
The pinout for the RJ-45 to DB9 cable is shown in the following table.
RJ-45
1
2
3
4,5
6
7
8
DB9
8
6
2
5
3
4
7
Summit® WM3700 Wireless LAN Controller Installation Guide
22
Supplying Power to the Summit WM3700 wireless LAN controller
2 On the configuration computer, configure a terminal emulation application (such as HyperTerminal)
as follows:
Terminal Type
VT-100
Port
COM port
Terminal Settings
19200bps transfer rate
8 data bits
no parity
1 stop bit
no flow control
no hardware compression
Supplying Power to the Summit WM3700 wireless
LAN controller
Rack mount
bracket
AC inlet
sym_0
1 Plug an approved AC power cord into the power connector at the back of the Summit WM3700
wireless LAN controller.
2 Plug the cord into a standard AC outlet with a voltage range of 100 to 240 VAC.
.
WARNING!
An improper shutdown can render the Summit WM3700 wireless LAN controller inoperable such that it
could require service by Extreme Networks Support. Do not remove AC power without first following the shutdown
procedure. An abrupt loss of power can corrupt the information stored on the device.
Verifying the Installation
View the LEDs on the front panel of the Summit WM3700 wireless LAN controller to ensure the device
is functioning properly. The normal LED pattern follows this path:
●
During the Power On Self Test (POST), the System 1 and System 2 LEDs both blink green.
Summit® WM3700 Wireless LAN Controller Installation Guide
23
Chapter 4: Hardware Setup
●
If the POST test fails, the System 1 LED will blink amber. If the POST test succeeds, the System 1
LED will be lit solid green.
●
As the software is initialized, the System 2 LED will blink green.
●
After the software has finished initializing, the System 1 LED will be lit solid green and the bottom
System 2 LED will be off. The Summit WM3700 wireless LAN controller is ready to be configured, as
described in the Summit WM3000 Series Controller System Reference Guide.
Other LED codes indicate the presence (or absence) of different standby states, or errors. A guide to the
Summit WM3700 wireless LAN controller LEDs codes is provided in Chapter , LED Codes.
Summit® WM3700 Wireless LAN Controller Installation Guide
24
5
Basic Configuration
CHAPTER
Once the Summit WM3700 Wireless LAN Controller hardware is installed and powered on, complete
the following steps to get the device up and running on and access the management functions on the
controller:
1 Connect one end of an Ethernet cable to the management port of the Summit WM3700 Wireless LAN
Controller, and connect the other end to a computer with a working Web browser.
2 Set the computer to use an IP address between 192.168.0.10 and 192.168.0.250 on the connected port.
Set a subnet / network mask of 255.255.255.0.
3 Once the computer has an IP address, point the Web browser to:
https://192.168.0.1/ and the following login screen will display.
4 Enter the default username admin in the Username field.
5 Enter the default password admin123 in the Password field.
6 Click the Login button to load the management interface.
Once the above basic settings have been defined or reviewed, you can set a more sophisticated
controller configuration in respect to your unique deployment requirements. Go to http://
www.extremenetworks.com/go/documentation to access the Summit WM3000 Series Controller System Reference
Guide.
Summit® WM3700 Wireless LAN Controller Installation Guide
25
Chapter 5: Basic Configuration
To login into the controller using the CLI:
Access the CLI by running a terminal emulation program on a computer connected to the serial port on
the front of the controller.
Login: admin
Password: admin123
Once you have logged in and accessed the controller’s CLI, you can set a more sophisticated controller
configuration in respect to your unique deployment requirements. Go to http://www.extremenetworks.com/
go/documentation to access the Summit® WM3000 Series Controller and Altitude™ 4000 Series Access Point
CLI Reference Guide.
Summit® WM3700 Wireless LAN Controller Installation Guide
26
6
Regulatory Information
CHAPTER
This regulatory section applies only to the Summit WM3700 wireless LAN controller.
All Extreme Networks devices are designed to be compliant with rules and regulations in locations they
are sold and will be labeled as required.
Any changes or modifications to Extreme Networks equipment, not expressly approved by Extreme
Networks, could void the user’s authority to operate the equipment.
!
Laser Devices - Gigabit Ethernet SFP Option
Complies with 21CFR1040.10 and 1040.11 except for deviations pursuant to Laser Notice No.
50, dated July 26, 2001.
EN60825-1:1994+ A1:2002 +A2:2001
IEC60825-1:1993+A1:1997+A2:2001
The laser classification is marked on the device.
Class 1 Laser devices are not considered to be hazardous when used for their intended purpose. The
following statement is required to comply with US and international regulations:
CAUTION
This is a class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Country Selection
Select only the country in which you are using the device. Any other selection will make the operation
of this device illegal.
Summit® WM3700 Wireless LAN Controller Installation Guide
27
Chapter 6: Regulatory Information
Radio Frequency Interference Requirements - FCC
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Radio Frequency Interference Requirements - Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Marking and European Economic Area (EEA)
Statement of Compliance
Extreme Networks, Inc., hereby declares that this device is in compliance with all the applicable
Directives, 89/336/EEC, 73/23/EEC. A Declaration of Conformity may be obtained from http://
www.extremenetworks.com/go/rfcertification.htm.
Summit® WM3700 Wireless LAN Controller Installation Guide
28
Statement of Compliance
Waste Electrical and Electronic Equipment (WEEE)
English: For EU Customers: All products at the end of their life must be returned to
Extreme Networks for recycling. For information on how to return product, please go
to:
http://www.extremenetworks.com/go/eu-weee.
http://www.extremenetworks.com/go/eu-weee
Dansk: Til kunder i EU: Alle produkter skal returneres til Extreme Networks til
recirkulering, når de er udtjent. Læs oplysningerne om returnering af produkter på:
http://www.extremenetworks.com/go/eu-weee.
Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer
Lebensdauer zum Recycling an Extreme Networks zurückgesandt werden.
Informationen zur Rücksendung von Produkten finden Sie unter http://
www.extremenetworks.com/go/eu-weee.
Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada
taaskasutamise eesmärgil Extreme Networks'ile. Lisainformatsiooni saamiseks toote
tagastamise kohta külastage palun aadressi: http://www.extremenetworks.com/go/euweee.
Español: Para clientes en la Unión Europea: todos los productos deberán entregarse
a Extreme Networks al final de su ciclo de vida para que sean reciclados. Si desea más
información sobre cómo devolver un producto, visite: http://
www.extremenetworks.com/go/eu-weee.
http://www.extremenetworks.com/go/eu-weee
Français : Clients de l'Union Européenne : Tous les produits en fin de cycle de vie
doivent être retournés à Extreme Networks pour recyclage. Pour de plus amples
informations sur le retour de produits, consultez : http://www.extremenetworks.com/
go/eu-weee.
Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo
ciclo di vita devono essere restituiti a Extreme Networks al fine di consentirne il
riciclaggio. Per informazioni sulle modalità di restituzione, visitare il seguente sito
Web:
http://www.extremenetworks.com/go/eu-weee.
http://www.extremenetworks.com/go/eu-weee
http://www.extremenetworks.com/go/eu-weee
Summit® WM3700 Wireless LAN Controller Installation Guide
29
Chapter 6: Regulatory Information
http://www.extremenetworks.com/go/eu-weee
Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun
levensduur naar Extreme Networks te worden teruggezonden voor recycling.
Raadpleeg
http://www.extremenetworks.com/go/eu-weee voor meer informatie over het
terugzenden van producten.
http://www.extremenetworks.com/go/eu-weee
Português: Para clientes da UE: todos os produtos no fim de vida devem ser
devolvidos à Extreme Networks para reciclagem. Para obter informações sobre como
devolver o produto, visite: http://www.extremenetworks.com/go/eu-weee.
Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti
podjetju Extreme Networks za reciklažo. Za informacije o vraèilu izdelka obišèite:
http://www.extremenetworks.com/go/eu-weee.
http://www.extremenetworks.com/go/eu-weee
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava
kierrätettäväksi Extreme Networks-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja
tuotteen palauttamisesta on osoitteessa http://www.extremenetworks.com/go/euweee.
Summit® WM3700 Wireless LAN Controller Installation Guide
30
7
Part Numbers and Support
CHAPTER
The following table lists the part numbers of the Summit WM3700 Wireless LAN controller and
available licenses.
Description
Part Number
Summit WM3700 Wireless LAN Controller
15710
16 AP license for Summit WM3700 Wireless LAN Controller
15711
64 AP license for Summit WM3700 Wireless LAN Controller
15712
256 AP license for Summit WM3700 Wireless LAN Controller
15718
Customer Service
NOTE
Services can be purchased from Extreme Networks or through one of its channel partners. If you are an
end-user who has purchased service through an Extreme Networks channel partner, please contact your partner
first for support.
Extreme Networks Technical Assistance Centers (TAC) provide 24x7x365 worldwide coverage. These
centers are the focal point of contact for post-sales technical and network-related questions or issues.
TAC will create a Service Request (SR) number and manage all aspects of the SR until it is resolved. For
a complete guide to customer support, see the Technical Assistance Center User Guide at:
http://www.extremenetworks.com/go/TACUserGuide
The Extreme Networks eSupport website provides the latest information on Extreme Networks
products, including the latest Release Notes, troubleshooting, downloadable updates or patches as
appropriate, and other useful information and resources. Directions for contacting the Extreme
Networks Technical Assistance Centers are also available from the eSupport website at:
https://esupport.extremenetworks.com
Summit® WM3700 Wireless LAN Controller Installation Guide
31
Chapter 7: Part Numbers and Support
Registration
If you have not already registered with Extreme Networks using a registration card supplied with your
product, you can register on the Extreme Networks website at:
http://www.extremenetworks.com/go/productregistration.
Documentation
Check for the latest versions of documentation on the Extreme Networks documentation website at:
http://www.extremenetworks.com/go/documentation
Summit® WM3700 Wireless LAN Controller Installation Guide
32
8
Extreme Networks, Inc. EndUser License Agreement
CHAPTER
NOTICE TO ALL USERS: PLEASE READ THIS CONTRACT CAREFULLY. BY CLICKING THE
ACCEPT BUTTON OR INSTALLING THE SOFTWARE, YOU AGREE THAT THIS AGREEMENT IS
ENFORCEABLE LIKE ANY WRITTEN CONTRACT SIGNED BY YOU AND EXTREME NETWORKS,
INC. (“EXTREME NETWORKS”). IF YOU DO NOT AGREE TO ALL THE TERMS OF THIS
AGREEMENT, DO NOT INSTALL OR USE THE SOFTWARE, AND RETURN IT TO THE SELLER FOR
A REFUND OR CREDIT.
1 Certain Definitions. As used in this Agreement “Software” means (a) all of the contents of the files,
disk(s), CD-ROM(s) or other media (including electronic media) with which this Agreement is
provided, or such contents as are hosted by Extreme Networks or its business partners (collectively
“Authorized Partner(s)”), including but not limited to (i) Extreme Networks or third party computer
information or software; (ii) related explanatory materials in printed, electronic, or online form
(“Documentation”); and (b) upgrades, modified or subsequent versions (collectively “Updates”), and
Software, if any, licensed to you by Extreme Networks or an Authorized Partner as part of a
maintenance contract or service subscription. “Use” or “Using” means to access, install, download,
copy or otherwise benefit from using the Software.
2 License Grant. Subject to the payment of the applicable license fees, and subject to the terms and
conditions of this Agreement, Extreme Networks hereby grants to you a non-exclusive, nontransferable license to Use one copy of the object code version of the Software for your internal
business purposes (subject to any restrictions or usage terms specified on the applicable price list or
product packaging included as part of the Documentation) for the time period specified in the
applicable product description or packaging for the Software (“License Period”). Software
embedded in hardware products may only be Used in conjunction with such hardware products.
You may make one (1) copy of the Software for back-up or archival purposes, provided that such
copy contains all of the Software.s proprietary notices unaltered. All rights not specifically granted
herein are reserved by Extreme Networks.
3 Term. This Agreement is effective for the License Period, unless terminated earlier as set forth herein.
This Agreement will terminate automatically if you fail to comply with any of the limitations or
other requirements of this Agreement. Upon any termination or expiration, you must cease Use of
the Software and destroy all copies of the Software.
4 Updates. This license is limited to the version of the Software delivered by Extreme Networks and
does not include Updates, unless a separate maintenance contract is purchased or unless an Update
is otherwise provided by Extreme Networks in its sole discretion. After the specified maintenance
period ends, you have no further rights to receive any Updates without purchase of a new license to
the Software.
5 Ownership Rights. The Software is protected by United States. and other copyright laws,
international treaty provisions and other applicable laws in the country in which it is being used.
Extreme Networks and its suppliers own and retain all right, title and interest in and to the Software,
Summit® WM3700 Wireless LAN Controller Installation Guide
33
Chapter 8: Extreme Networks, Inc. End-User License Agreement
including all copyrights, patents, trade secret rights, trademarks and other intellectual property
rights therein. Your possession or Use of the Software does not transfer to you any title to the
intellectual property in the Software, and you will not acquire any rights to the Software except as
expressly set forth in this Agreement. Any copy of the Software authorized to be made under this
Agreement must contain the same proprietary notices that appear on and in such Software.
6 Evaluation Product Additional Terms. If the product you have received with this license has been
identified as “Beta” Software, then the provisions of this section apply. To the extent that any
provision in this section is in conflict with any other term or condition in this Agreement, this
section shall supercede such other term(s) and condition(s) with respect to the Beta Software, but
only to the extent necessary to resolve the conflict. You acknowledge that the Beta Software may
contain bugs, errors and other problems that could cause system or other failures and data loss.
Consequently, Beta Software is provided to you “AS-IS”, and Extreme Networks disclaims any
warranty or liability obligations to you of any kind. WHERE LEGAL LIABILITY CANNOT BE
EXCLUDED, BUT MAY BE LIMITED, EXTREME NETWORKS. LIABILITY AND THAT OF ITS
SUPPLIERS AND AUTHORIZED PARTNERS SHALL BE LIMITED TO THE SUM OF FIFTY
DOLLARS (U.S. $50) IN TOTAL. You acknowledge that Extreme Networks has not promised or
guaranteed to you that Beta Software will be announced or made available to anyone in the future;
that Extreme Networks has no express or implied obligation to you to announce or introduce the
Beta Software; and that Extreme Networks may not introduce a product similar to or compatible
with the Beta Software. Accordingly, you acknowledge that any research or development that you
perform regarding the Beta Software or any product associated with the Beta Software is done
entirely at your own risk. During the term of this Agreement, you will provide feedback to Extreme
Networks upon request regarding testing and use of the Beta Software, including error or bug
reports. If you have been provided the Beta Software pursuant to a separate written agreement, your
use of the Beta Software is also governed by such agreement. Your Use and evaluation of the Beta
Software is deemed the Confidential Information of Extreme Networks, and will not be disclosed to
any third party without Extreme Networks. prior written consent. Upon receipt of a later unreleased
version of the Beta Software or release by Extreme Networks of a publicly released commercial
version of the Beta Software, whether as a stand-alone product or as part of a larger product, you
agree to return or destroy all earlier Beta Software received from Extreme Networks and to abide by
the terms of the End User License Agreement for any such later versions of the Beta Software. Your
Use of the Beta Software is limited to 30 days unless otherwise agreed to in writing by Extreme
Networks.
7 Restrictions. You may not sell, lease, license, rent, loan, resell or otherwise transfer the Software, with
or without consideration. If you enter into a contract with a third party in which the third party
manages your information technology resources (“Managing Party”), you may transfer all your
rights to Use the Software to such Managing Party, provided that (a) the Managing Party only Uses
the Software for your internal operations and not for the benefit of another third party; (b) the
Managing Party agrees to comply with the terms and conditions of this Agreement, and (c) you
provide Extreme Networks with written notice that a Managing Party will be Using the Software on
your behalf. You may not permit third parties to benefit from the use or functionality of the
Software via a timesharing, service bureau or other arrangement. Except to the extent Extreme
Networks may, in certain jurisdictions, be required by law to permit reverse engineering and
provided that the provisions of such law may not be waived or conditioned on prior request for
information regarding interoperability, You may not disassemble, decompile or otherwise reverse
engineer the Software nor permit any third party to do so.
You may not modify, or create derivative works based upon, the Software in whole or in part. You
may not copy the Software or Documentation except as expressly permitted in Section 2 above. You
may not remove any proprietary notices or labels on the Software. All rights not expressly set forth
hereunder are reserved by Extreme Networks.
8 Warranty and Disclaimer.
Summit® WM3700 Wireless LAN Controller Installation Guide
34
a Limited Warranty. Extreme Networks warrants that for sixty (60) days from the date of original
purchase the media (e.g., CD ROM), if any, on which the Software is contained will be free from
defects in materials and workmanship. Extreme Networks. and its suppliers’ entire liability and
your exclusive remedy for any breach of the foregoing warranty shall be, at Extreme Networks.
option, either (i) return of the purchase price paid for the license, if any, or (ii) replacement of the
defective media in which the Software is contained. You must return the defective media to
Extreme Networks at your expense. This limited warranty is void if the defect has resulted from
accident, abuse, or misapplication. Any replacement media will be warranted for the remainder
of the original warranty period. Outside the United States, this remedy is not available to the
extent Extreme Networks is subject to restrictions under United States export control laws and
regulations, or prohibited by other laws and regulations.
b Software Warranty and Disclaimer. Extreme Networks warrants the Software solely to End Users
and subject to the terms and conditions of the Extreme Networks standard warranty card
provided with the Software. Except for the limited warranty set forth therein, THE SOFTWARE
IS PROVIDED “AS IS” AND EXTREME NETWORKS MAKES NO WARRANTY AS TO USE OR
PERFORMANCE. EXCEPT TO THE EXTENT SUCH EXCLUSIONS OR LIMITATIONS ARE
PROHIBITED BY APPLICABLE LAW, EXTREME NETWORKS, ITS SUPPLIERS AND
AUTHORIZED PARTNERS MAKE NO WARRANTY, CONDITION, REPRESENTATION, OR
TERM (EXPRESS OR IMPLIED, WHETHER BY STATUTE, COMMOM LAW, CUSTOM, USAGE
OR OTHERWISE) AS TO ANY MATTER INCLUDING, WITHOUT LIMITATION,
NONINFRINGEMENT OF THIRD PARTY RIGHTS, MERCHANTABILITY, SATISFACTORY
QUALITY, INTEGRATION, OR FITNESS FOR A PARTICULAR PURPOSE. You assume
responsibility for selecting the Software to achieve your intended results, and for your Use
thereof. WITHOUT LIMITING THE FOREGOING PROVISIONS, EXTREME NETWORKS
MAKES NO WARRANTY THAT THE SOFTWARE WILL BE ERROR-FREE OR FREE FROM
INTERRUPTIONS OR OTHER FAILURES, OR THAT THE SOFTWARE WILL MEET YOUR
REQUIREMENTS.
9 Limitation of Liability. UNDER NO CIRCUMSTANCES AND UNDER NO LEGAL THEORY,
WHETHER IN TORT, CONTRACT, OR OTHERWISE, SHALL EXTREME NETWORKS OR ITS
AUTHORIZED PARTNERS OR SUPPLIERS BE LIABLE TO YOU OR TO ANY OTHER PERSON
FOR LOSS OF PROFITS, LOSS OF GOODWILL OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES OR DAMAGES FOR GROSS NEGLIGENCE OF ANY CHARACTER
INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF GOODWILL, WORK
STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, OR FOR ANY OTHER DAMAGE OR
LOSS. IN NO EVENT SHALL EXTREME NETWORKS OR ITS AUTHORIZED PARTNERS OR
SUPPLIERS BE LIABLE FOR ANY DAMAGE IN EXCESS OF THE PRICE PAID FOR THE
SOFTWARE, IF ANY, EVEN IF EXTREME NETWORKS OR ITS AUTHORIZED PARTNERS OR
SUPPLIERS SHALL HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. This
limitation shall not apply to liability for death or personal injury to the extent that applicable law
prohibits such limitation. Extreme Networks is acting on behalf of its suppliers for the purpose of
disclaiming, excluding and/or limiting obligations, warranties and liability as provided in this
Agreement, but in no other respects and for no other purpose. The foregoing provisions shall be
enforceable to the maximum extent permitted by applicable law.
10 Notice to United States Government End Users. The Software and accompanying Documentation are
deemed to be “commercial computer software” and “commercial computer software
documentation,” respectively, pursuant to DFAR Section 227.7202 and FAR Section 12.212, as
applicable. Any use, modification, reproduction, release, performance, display or disclosure of the
Software and accompanying Documentation by the United States Government shall be governed
solely by the terms of this Agreement and shall be prohibited except to the extent expressly
permitted by the terms of this Agreement.
11 Export Controls. You are advised that the Software is of United States origin and subject to United
States Export Administration Regulations; diversion contrary to United States law and regulation is
Summit® WM3700 Wireless LAN Controller Installation Guide
35
Chapter 8: Extreme Networks, Inc. End-User License Agreement
prohibited. You agree not to directly or indirectly export, import or transmit the Software to any
country, end user or for any Use that is prohibited by applicable United States regulation or statute
(including but not limited to those countries embargoed from time to time by the United States
government); or contrary to the laws or regulations of any other governmental entity that has
jurisdiction over such export, import, transmission or Use.
12 High Risk Activities. The Software is not fault-tolerant and is not designed or intended for use in
hazardous environments requiring fail-safe performance, including without limitation, in the
operation of nuclear facilities, aircraft navigation or communication systems, air traffic control,
weapons systems, direct life-support machines, or any other application in which the failure of the
Software could lead directly to death, personal injury, or severe physical or property damage
(collectively, “High Risk Activities”). EXTREME NETWORKS EXPRESSLY DISCLAIMS ANY
EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR HIGH RISK ACTIVITIES.
13 Governing Law. This Agreement will be governed by and construed in accordance with the
substantive laws of the State of California. This Agreement will not be governed by the conflict of
laws rules of any jurisdiction or the United Nations Convention on Contracts for the International
Sale of Goods, the application of which is expressly excluded. The state and federal courts sitting in
Santa Clara County, California shall have exclusive jurisdiction over all disputes relating to this
Agreement.
14 Open Source Software. Portions of the Software (“Open Source Software”) provided to you may be
subject to a license that permits you to modify these portions and redistribute the modifications (an
“Open Source License”). Your use, modification and redistribution of the Open Source Software are
governed by the terms and conditions of the applicable Open Source License. More details
regarding the Open Source Software and the applicable Open Source Licenses are available at
www.extremenetworks.com/services/SoftwareLicensing.aspx. Some of the Open Source software
may be subject to the GNU General Public License v.2 (“GPL”) or the Lesser General Public Library
(“LGPL”), copies of which are available at www.extremenetworks.com/services/
SoftwareLicensing.aspx. In accordance with the terms of the GPL and LGPL, you may request a
copy of the relevant source code. See the Software Licensing web site for details. This offer is valid
for up to three years from the date of original download of the software.
15 Audit for Compliance. Extreme Networks reserves the right to periodically audit you to ensure that
you are in compliance with the terms of this Agreement. During standard business hours and upon
prior written notice, Extreme Networks may visit You and You will make available to Extreme
Networks or its representatives any records pertaining to the Software. The cost of any requested
audit will be solely borne by Extreme Networks, unless such audit discloses an underpayment or
amount due to Extreme Networks in excess of five percent (5%) of the initial license fee for the
Software or you are using the Software in an unauthorized manner, in which case you shall pay the
cost of the audit, in addition to any other amounts owed.
16 Miscellaneous. This Agreement sets forth all rights for the user of the Software and is the entire
Agreement between the parties. This Agreement supersedes any other communications,
representations or advertising relating to the Software and Documentation. This Agreement may not
be modified except by a written addendum issued by a duly authorized representative of Extreme
Networks. No provision hereof shall be deemed waived unless such waiver shall be in writing and
signed by Extreme Networks. If any provision of this Agreement is held invalid, the remainder of
this Agreement shall continue in full force and effect.
Summit® WM3700 Wireless LAN Controller Installation Guide
36