advertisement
RKHD Heavy Duty Alignment Pit System
Pit Rack
SPECIFICATIONS
RKHD Pit Turnplates
TURNPLATE
SECTION
Pit Construction
Minimum Concrete Spec.
Site Specifications
Refer to Forms 5097-T and 5004-T
4 in. (102 mm) thick, 3000 PSI (20700 kPA) rating
New Floor Concrete Spec.
6 in. (152 mm) thick, 3000 PSI (20700 kPA) rating
Pre-Installation Kit Required before pouring pit.
Pit Contractor Pre-Pack
Pit Edging
None Available
Field Fabricated / Purchased
Product Specification
20,000 lbs. (9072 kg) Max. Axle Weight
Rear Axle Jack Rail
Track Width
(inside and outside width)
Pit Depth (nominal)
Adjustable Legs
(accomodates floor slope)
Typically N/A, rails available for opt. jack tray
Fixed Runway, Typical Spacing
40 - 106 inches (1016 - 2692 mm)
24 or 30 inches (610 or 762 mm)
3 1/2 inches (89 mm) longer than nominal
2 1/4 inches (57 mm) shorter than nominal
MODULAR
RUNWAY
SECTION
(three pairs within shown example)
PIT ADAPTOR
(secures runway to pit back wall)
RKHD Pit Illustration
MODEL COMPARISON
Features
Capacity
Axle Jack Rail
Work Beam
Pit Depth
Track Width
(inside - outside width)
PT
Heavy Duty
18,000 lbs. / axle
(8165 kg)
PF
Heavy Duty
18,000 lbs. / axle
(8165 kg) optional
T-Pit
N/A
58 in.
(1473 mm)
Adjustable Runways
48 in. - 120 in
(1219 mm - 3048 mm)
58 in.
(1473 mm)
Adjustable Runways
48 in. - 120 in
(1219 mm - 3048 mm)
RKHD
Heavy Duty
20,000 lbs. / axle
(9072 kg) optional jack tray
N/A
24 or 30 in.
(610 mm or 762 mm)
Fixed Runways
40 in. - 106 in.
(1016 mm - 2692 mm)
PE
Meduim Duty
10,000 lbs. / axle
(4535 kg)
N/A
P44x
Light Duty
18,000 lbs. Total
(8165 kg)
36 in.
(914 mm)
Adjustable Runways
48 in. - 120 in
(1219 mm - 3048 mm)
N/A
36 in.
(30 & 24 in. available)
(914, 762 or 610 mm)
Fixed Runways
40 in. - 85 in.
(1016 mm - 2159 mm)
For general inquiries visit: or call
800-448-6848
Continued on Page 2
For local contact visit: www.hunter.com/company/findrep.cfm
Form 6947-T, 03-15b
Copyright © 2015, Hunter Engineering Company
RKHD Heavy Duty Alignment Pit System
Pit Rack
LAY-O UT Construct pit per referenced forms.
RECOMMENDED MINIMUM WIDTH
15 ft. (4572 mm)
EXAMPLE
SHOWN HAS A
TURNPLATE
SECTION WITH
TWO RUNWAY
SECTIONS
PIT DEPTH:
24 in. (610 mm)
OR
30 in. (762 mm)
PIT FLOOR SPECIFICATION:
4 in. THICK , 3000 PSI MINIMUM
FOR AN EXISTING FLOOR
(6 in. THICK , 3000 PSI
RECOMMENDED FOR
A NEW FLOOR)
HANDRAIL AND
STEPS ARE
CONTRACTOR
SUPPLIED TO
LOCAL CODE
RECOMMENDED
MINIMUM
72 in. (1829 mm)
64 in.
(1626 mm)
DRAIN
EDGING,
HANDRAIL AND
STEPS ARE
CONTRACTOR
SUPPLIED
PLUS 46 in.
(1168 mm)
FOR EACH
SET OF
RUNWAY
SECTIONS
REAR WALL
SPECIFICATION:
6 in. THICK,
3000 PSI MIN.
33 in.
(838 mm)
40 in.
(1016 mm)
OR TO
CUSTOMER
SPEC.*
Anchoring Details (inches)
The following items are to be supplied by the customer:
Concrete to construct pit / Concrete reinforcement / Electrical fixtures, wiring, and power (if necessary) / Piping /
Pit ventilation materials / Drainage materials / Edging / Railings / lifting equipment for installation.
Form 6947-T, 03-15b
Copyright © 2015, Hunter Engineering Company
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project