Husqvarna 2146XLS User's Manual

03002
2146XLS
Owner's Manual / 96043006700 / 2008-11
SAFETY RULES
Safe Operation Practices for Ride-On Mowers
DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE
TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
•
WARNING: In order to prevent accidental starting when setting up,
transporting, adjusting or making
repairs, always disconnect spark plug
wire and place wire where it cannot
contact spark plug.
•
•
•
WARNING: Do not coast down a hill
in neutral, you may lose control of
the tractor.
•
•
WARNING: Tow only the attachments
that are recommended by and comply
with specifications of the manufacturer
of your tractor. Use common sense
when towing. Operate only at the lowest possible speed when on a slope.
Too heavy of a load, while on a slope,
is dangerous. Tires can lose traction
with the ground and cause you to lose
control of your tractor.
•
•
•
•
•
WARNING
•
Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals
known to the State of California to cause cancer and
birth defects or other reproductive harm.
II. SLOPE OPERATION
WARNING
Slopes are a major factor related to loss of control and
tip-over accidents, which can result in severe injury or
death. Operation on all slopes requires extra caution. If
you cannot back up the slope or if you feel uneasy on it,
do not mow it.
• Mow up and down slopes, not across.
• Watch for holes, ruts, bumps, rocks, or other hidden
objects. Uneven terrain could overturn the machine.
Tall grass can hide obstacles.
• Choose a low ground speed so that you will not have
to stop or shift while on the slope.
• Do not mow on wet grass. Tires may lose traction.
Always keep the machine in gear when going down
slopes. Do not shift to neutral and coast downhill.
• Avoid starting, stopping, or turning on a slope. If the
tires lose traction, disengage the blades and proceed
slowly straight down the slope.
• Keep all movement on the slopes slow and gradual.
Do not make sudden changes in speed or direction,
which could cause the machine to roll over.
• Use extra care while operating machine with grass
catchers or other attachments; they can affect the
stability of the machine. Do no use on steep slopes.
• Do not try to stabilize the machine by putting your foot
on the ground.
• Do not mow near drop-offs, ditches, or embankments.
The machine could suddenly roll over if a wheel is over
the edge or if the edge caves in.
Battery posts, terminals and related accessories
contain lead and lead compounds, chemicals known
to the State of California to cause cancer and birth
defects or other reproductive harm. Wash hands
after handling.
I. GENERAL OPERATION
•
•
•
•
•
•
•
•
Do not operate machine without the entire grass catcher,
discharge guard, or other safety devices in place and
working.
Slow down before turning.
Never leave a running machine unattended. Always
turn off blades, set parking brake, stop engine, and
remove keys before dismounting.
Disengage blades when not mowing. Shut off engine
and wait for all parts to come to a complete stop before
cleaning the machine, removing the grass catcher, or
unclogging the discharge guard.
Operate machine only in daylight or good artificial
light.
Do not operate the machine while under the influence
of alcohol or drugs.
Watch for traffic when operating near or crossing
roadways.
Use extra care when loading or unloading the machine
into a trailer or truck.
Always wear eye protection when operating machine.
Data indicates that operators, age 60 years and above,
are involved in a large percentage of riding mowerrelated injuries. These operators should evaluate their
ability to operate the riding mower safely enough to
protect themselves and others from serious injury.
Follow the manufacturer's recommendation for wheel
weights or counterweights.
Keep machine free of grass , leaves or other debris
build-up which can touch hot exhaust / engine parts
and burn. Do not allow the mower deck to plow leaves
or other debris which can cause build-up to occur.
Clean any oil or fuel spillage before operating or
storing the machine. Allow machine to cool before
storage.
Read, understand, and follow all instructions on the
machine and in the manual before starting.
Do not put hands or feet near rotating parts or under
the machine. Keep clear of the discharge opening at
all times.
Only allow responsible adults, who are familiar with
the instructions, to operate the machine.
Clear the area of objects such as rocks, toys, wire, etc.,
which could be picked up and thrown by the blades.
Be sure the area is clear of bystanders before operating. Stop machine if anyone enters the area.
Never carry passengers.
Do not mow in reverse unless absolutely necessary.
Always look down and behind before and while backing.
Never direct discharged material toward anyone. Avoid
discharging material against a wall or obstruction.
Material may ricochet back toward the operator. Stop
the blades when crossing gravel surfaces.
2
SAFETY RULES
Safe Operation Practices for Ride-On Mowers
III. CHILDREN
GENERAL SERVICE
• Never operate machine in a closed area.
• Keep all nuts and bolts tight to be sure the equipment
is in safe working condition.
• Never tamper with safety devices. Check their proper
operation regularly.
• Keep machine free of grass, leaves, or other debris
build-up. Clean oil or fuel spillage and remove any
fuel-soaked debris. Allow machine to cool before
storing.
• If you strike a foreign object, stop and inspect the
machine. Repair, if necessary, before restarting.
• Never make any adjustments or repairs with the engine
running.
• Check grass catcher components and the discharge
guard frequently and replace with manufacturer's recommended parts, when necessary.
• Mower blades are sharp. Wrap the blade or wear
gloves, and use extra caution when servicing them.
• Check brake operation frequently. Adjust and service
as required.
• Maintain or replace safety and instruction labels, as
necessary.
Tragic accidents can occur if the operator is not alert to
the presence of children. Children are often attracted to
the machine and the mowing activity. Never assume that
children will remain where you last saw them.
• Keep children out of the mowing area and in the watchful
care of a responsible adult other than the operator.
• Be alert and turn machine off if a child enters the area.
• Before and while backing, look behind and down for
small children.
• Never carry children, even with the blades shut off. They
may fall off and be seriously injured or interfere with
safe machine operation. Children who have been given
rides in the past may suddenly appear in the mowing
area for another ride and be run over or backed over
by the machine.
• Never allow children to operate the machine.
• Use extra care when approaching blind corners, shrubs,
trees, or other objects that may block your view of a
child.
IV. TOWING
•
•
•
•
•
Tow only with a machine that has a hitch designed for
towing. Do not attach towed equipment except at the
hitch point.
Follow the manufacturer's recommendation for weight
limits for towed equipment and towing on slopes.
Never allow children or others in or on towed equipment.
On slopes, the weight of the towed equipment may
cause loss of traction and loss of control.
Travel slowly and allow extra distance to stop.
•
•
•
V. SERVICE
SAFE HANDLING OF GASOLINE
To avoid personal injury or property damage, use extreme
care in handling gasoline. Gasoline is extremely flammable
and the vapors are explosive.
• Extinguish all cigarettes, cigars, pipes, and other
sources of ignition.
• Use only approved gasoline container.
• Never remove gas cap or add fuel with the engine
running. Allow engine to cool before refueling.
• Never fuel the machine indoors.
• Never store the machine or fuel container where there
is an open flame, spark, or pilot light such as on a water
heater or other appliances.
• Never fill containers inside a vehicle or on a truck or
trailer bed with plastic liner. Always place containers
on the ground away from your vehicle when filling.
• Remove gas-powered equipment from the truck or
trailer and refuel it on the ground. If this is not possible,
then refuel such equipment with a portable container,
rather than from a gasoline dispenser nozzle.
• Keep the nozzle in contact with the rim of the fuel tank or
container opening at all times until fueling is complete.
Do not use a nozzle lock-open device.
• If fuel is spilled on clothing, change clothing immediately.
• Never overfill fuel tank. Replace gas cap and tighten
securely.
•
•
•
•
•
•
•
•
•
3
Be sure the area is clear of bystanders before operating. Stop machine if anyone enters the area.
Never carry passengers.
Do not mow in reverse unless absolutely necessary.
Always look down and behind before and while backing.
Never carry children, even with the blades shut off. They
may fall off and be seriously injured or interfere with
safe machine operation. Children who have been given
rides in the past may suddenly appear in the mowing
area for another ride and be run over or backed over
by the machine.
Keep children out of the mowing area and in the watchful
care of a responsible adult other than the operator.
Be alert and turn machine off if a child enters the
area.
Before and while backing, look behind and down for
small children.
Mow up and down slopes (15° Max), not across.
Choose a low ground speed so that you will not have
to stop or shift while on the slope.
Avoid starting, stopping, or turning on a slope. If the
tires lose traction, disengage the blades and proceed
slowly straight down the slope.
If machine stops while going uphill, disengage blades,
shift into reverse and back down slowly.
Do not turn on slopes unless necessary, and then, turn
slowly and gradually downhill, if possible.
PRODUCT SPECIFICATIONS
Gasoline Capacity
and type:
4.0 Gallons
Unleaded Regular
Oil Type (API-SG-SL):
SAE 30 (above 32°F)
SAE 5W-30 (below 32°F)
Oil Capacity:
W/ Filter:
W/O Filter:
Spark Plug:
Champion QC12YC
(Gap: .040")
Ground Speed (MPH):
Forward:
Reverse:
Charging System:
16 AMPS @ 3600 RPM
Battery:
AMP/HR:
MIN. CCA:
Case Size:
Blade Bolt Torque:
45-55 FT. LBS.
CONGRATULATIONS on your purchase of a new tractor.
It has been designed, engineered and manufactured to give
you the best possible dependability and performance.
Should you experience any problem you cannot easily remedy, please contact your nearest authorized servicecenter/
department We have competent, well-trained technicians
and the proper tools to service or repair this tractor.
Please read and retain this manual. The instructions will
enable you to assemble and maintain your tractor properly.
Always observe the “SAFETY RULES”.
64 oz
60 oz
0 - 5.5
0 - 2.4
CUSTOMER RESPONSIBILITIES
•
•
28
230
U1R
•
Read and observe the safety rules.
Follow a regular schedule in maintaining, caring for
and using your tractor.
Follow the instructions under “Maintenance” and “Storage” sections of this owner’s manual.
WARNING: This tractor is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered or grass-covered
land unless the engine’s exhaust system is equipped with
a spark arrester meeting applicable local or state laws (if
any). If a spark arrester is used, it should be maintained
in effective working order by the operator.
In the state of California the above is required by law
(Section 4442 of the California Public Resources Code).
Other states may have similar laws. Federal laws apply
on federal lands.
A spark arrester for the muffler is available through your
nearest authorized service center/department.
TABLE OF CONTENTS
SAFETY RULES ......................................................... 2-3
PRODUCT SPECIFICATIONS ....................................... 4
CUSTOMER RESPONSIBILITIES................................. 4
ASSEMBLY ................................................................. 5-6
OPERATION ............................................................. 7-13
MAINTENANCE SCHEDULE ...................................... 14
MAINTENANCE ..................................................... 14-17
SERVICE AND ADJUSTMENTS ............................ 18-23
STORAGE .................................................................... 24
TROUBLESHOOTING ............................................ 25-26
REPAIR PARTS ...................................................... 27-42
4
UNASSEMBLED PARTS
Slope Sheet
Key
(1) Oil Drain Tube
(2) Keys
ASSEMBLY
Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes.
TOOLS REQUIRED FOR ASSEMBLY
A socket wrench set will make assembly easier. Standard
wrench sizes are listed.
(1) 1/2" wrench
Tire pressure gauge
(2) 7/16" wrenches
Utility knife
Pliers
When right or left hand is mentioned in this manual, it means
when you are in the operating position (seated behind the
steering wheel).
LABEL
TO REMOVE TRACTOR FROM CARTON
UNPACK CARTON
•
•
•
FIG. 1
Remove all accessible loose parts and parts cartons
from carton .
Cut along dotted lines on all four panels of carton.
Remove end panels and lay side panels flat.
Check for any additional loose parts or cartons and
remove.
TO ADJUST SEAT (See Fig. 2)
•
Grasp adjustment handle(A) and pull up, slide seat to
desired position and release adjustment handle.
BEFORE REMOVING TRACTOR FROM
SKID
A
TO CHECK BATTERY (See Fig. 1)
•
Lift hood to raised position.
NOTE: If this battery is put into service after month and
year indicated on label (label is located between terminals)
charge battery for minimum of one hour at 6-10 amps.
(See "BATTERY" in Maintenance section of this manual
for charging instructions).
•
For battery and battery cable installation see "REPLACING BATTERY" in the "Service and Adjustments"
section in this manual.
FIG. 2
5
ASSEMBLY
✓CHECKLIST
NOTE: You may now roll your tractor off the skid. Follow the
instructions below to remove the tractor from the skid.
BEFORE YOU OPERATE YOUR NEW TRACTOR, WE
WISH TO ASSURE THAT YOU RECEIVE THE BEST
PERFORMANCE AND SATISFACTION FROM THIS
QUALITY PRODUCT.
PLEASE REVIEW THE FOLLOWING CHECKLIST:
✓ All assembly instructions have been completed.
✓ No remaining loose parts in carton.
✓ Battery is properly prepared and charged.
✓ Seat is adjusted comfortably and tightened securely.
✓ All tires are properly inflated. (For shipping purposes,
the tires were overinflated at the factory).
✓ Be sure mower deck is properly leveled side-to-side/
front-to-rear for best cutting results. (Tires must be
properly inflated for leveling).
✓ Check mower and drive belts. Be sure they are routed
properly around pulleys and inside all belt keepers.
✓ Check wiring. See that all connections are still secure
and wires are properly clamped.
✓ Before driving tractor, be sure freewheel control is in
“transmission engaged” position (see “TO TRANSPORT” in the Operation section of this manual).
WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY
EXTRA ATTENTION TO THE FOLLOWING IMPORTANT
ITEMS:
✓ Engine oil is at proper level.
✓ Fuel tank is filled with fresh, clean, regular unleaded
gasoline.
✓ Become familiar with all controls, their location and
function. Operate them before you start the engine.
✓ Be sure brake system is in safe operating condition.
✓ Be sure Operator Presence System and Reverse
Operation System (ROS) are working properly (See the
Operation and Maintenance sections in this manual).
✓ It is important to purge the transmission before
operating your tractor for the first time. Follow proper
starting and transmission purging instructions (See “TO
START ENGINE” and “PURGE TRANSMISSION” in
the Operation section of this manual).
WARNING: Before starting, read, understand and follow
all instructions in the Operation section of this manual. Be
sure tractor is in a well-ventilated area. Be sure the area in
front of tractor is clear of other people and objects.
TO ROLL TRACTOR OFF SKID (See Operation
section for location and function of controls)
•
•
•
Raise attachment lift lever to its highest position.
Release parking brake by depressing clutch/brake pedal.
Place freewheel control in "transmission disengaged"
position (See “TO TRANSPORT” in the Operation
section of this manual).
• Roll tractor forward off skid.
• Remove banding holding the deflector shield up against
tractor.
Continue with the instructions that follow.
CHECK TIRE PRESSURE
The tires on your tractor were overinflated at the factory
for shipping purposes. Correct tire pressure is important
for best cutting performance.
• Reduce tire pressure to PSI shown on tires.
CHECK DECK LEVELNESS
For best cutting results, mower housing should be properly leveled. See “TO LEVEL MOWER HOUSING” in the
Service and Adjustments section of this manual.
CHECK FOR PROPER POSITION OF ALL
BELTS
See the figures that are shown for replacing motion and
mower blade drive belts in the Service and Adjustments
section of this manual. Verify that the belts are routed
correctly.
CHECK BRAKE SYSTEM
After you learn how to operate your tractor, check to see that
the brake is operating properly. See “TO CHECK BRAKE”
in the Service and Adjustments section of this manual.
6
OPERATION
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.
REVERSE
ENGINE OFF
LIGHTS ON
NEUTRAL
REVERSE
OPERATION
SYSTEM (ROS)
FUEL
HIGH
LOW
ENGINE ON
BATTERY
CHOKE
ENGINE START
REVERSE
FAST
IGNITION SWITCH
PARKING BRAKE
FORWARD
SLOW
MOWER HEIGHT
MOWER LIFT
CLUTCH/BRAKE
PEDAL
CRUISE CONTROL
15
ATTACHMENT
CLUTCH DISENGAGED
ATTACHMENT
CLUTCH ENGAGED
DANGER, KEEP HANDS
AND FEET AWAY
15
SLOPE HAZARDS
KEEP AREA CLEAR
(SEE SAFETY RULES SECTION)
DANGER indicates a hazard which, if not avoided,
will result in death or serious injury.
FREE WHEEL
(Automatic Models only)
WARNING indicates a hazard which, if not avoided,
could result in death or serious injury.
CAUTION indicates a hazard which, if not avoided,
might result in minor or moderate injury.
CAUTION when used without the alert symbol,
indicates a situation that could result in damage
to the tractor and/or engine.
Failure to follow instructions
could result in serious injury or
death. The safety alert symbol
is used to identify safety information about hazards which can
result in death, serious injury
and/or property damage.
HOT SURFACES indicates a hazard which,
if not avoided, could result in death, serious injury
and/or property damage.
FIRE indicates a hazard which, if not avoided,
could result in death, serious injury and/or
property damage.
7
OPERATION
KNOW YOUR TRACTOR
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR
Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments.
Save this manual for future reference.
D
P
H
Z
G
E
F
B
A
M
Q
C
J
K
L
FIG. 3
Our tractors conform to the applicable safety standards of the American National Standards Institute.
(A) ATTACHMENT LIFT LEVER - Used to raise and lower
the mower or other attachments mounted to your tractor.
(B) BRAKE PEDAL - Used for braking the tractor and
starting the engine.
(C) PARKING BRAKE - Locks clutch/brake pedal into
the brake position.
(D) THROTTLE/CHOKE CONTROL - Used for starting
and controlling engine speed.
(E) ATTACHMENT CLUTCH SWITCH - Used to engage the
mower blades or other attachments mounted to your tractor.
(F) IGNITION SWITCH - Used for starting and stopping
the engine.
(G) REVERSE OPERATION SYSTEM (ROS) "ON"
POSITION - Allows operation of mower or other powered
attachment while in reverse.
(H) LIGHT SWITCH - Turns the headlights on and off.
(J) CRUISE CONTROL LEVER - Used to set forward
movement of tractor at desired speed without holding the
forward drive pedal.
(K) FORWARD DRIVE PEDAL - Used for forward movement of tractor.
(L) REVERSE DRIVE PEDAL - Used for reverse movement of tractor.
(M) FREEWHEEL CONTROL - Disengages transmission
for pushing or slowly towing the tractor with the engine off.
(P) SERVICE REMINDER / HOUR METER - Indicates
when service is required for the engine and mower.
(Q) 12-VOLT POWER PORT - Used for 12 volt accessories.
(Z) AMMETER - Indicates charging (+) or discharging (-)
of battery.
8
OPERATION
The operation of any tractor can result in foreign objects thrown into the eyes, which can result
in severe eye damage. Always wear safety glasses or eye shields while operating your tractor
or performing any adjustments or repairs. We recommend standard safety glasses or a wide
vision safety mask worn over spectacles.
HOW TO USE YOUR TRACTOR
ENGINE • Move throttle control (D) between half and full speed
(fast) position.
NOTE: Failure to move throttle control between half and full
speed (fast) position, before stopping may cause engine
to “backfire”.
• Turn ignition key (F) to “STOP” position and remove key.
Always remove key when leaving tractor to prevent
unauthorized use.
• Never use the choke to stop the engine.
TO SET PARKING BRAKE(See Fig. 4)
Your tractor is equipped with an operator presence sensing switch. When engine is running, any attempt by the
operator to leave the seat without first setting the parking
brake will shut off the engine.
• Depress brake pedal (B) all the way down and hold.
• Pull parking brake lever (C) up and hold, release pressure from brake pedal (B), then release parking brake
lever. Pedal should remain in brake position. Make
sure parking brake will hold tractor secure.
IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY
POSITION OTHER THAN "STOP" WILL CAUSE THE BATTERY
TO BE DISCHARGED, (DEAD).
C
NOTE: Under certain conditions when tractor is standing
idle with the engine running, hot engine exhaust gases may
cause “browning” of grass. To eliminate this possibility, always stop engine when stopping tractor on grass areas.
B
CAUTION: Always stop tractor completely, as described above, and set
parking brake before leaving the operator's position.
FIG. 4
STOPPING (See Fig. 5)
MOWER BLADES • To stop mower blades, place attachment clutch control
in the “DISENGAGED” position ( ).
TO USE THROTTLE CONTROL (D) (See Fig.6)
Always operate engine at full speed (fast).
• Operating engine at less than full speed (fast) reduces
the engine's operating efficiency.
• Full speed (fast) offers the best mower performance.
D
(
) ATTACHMENT
CLUTCH SWITCH
“DISENGAGED”
(
) ATTACHMENT
CLUTCH SWITCH
“ENGAGED”
F
FIG. 5
GROUND DRIVE • To stop ground drive, depress brake pedal into full
“BRAKE” position.
FIG. 6
IMPORTANT: FORWARD AND REVERSE DRIVE PEDALS
RETURN TO NEUTRAL POSITION WHEN NOT DEPRESSED.
9
OPERATION
TO MOVE FORWARD AND BACKWARD
(See Fig. 7)
• Put attachment lift lever in desired cutting height slot.
The cutting height range is approximately 1" to 4". The
heights are measured from the ground to the blade tip with
the engine not running. These heights are approximate
and may vary depending upon soil conditions, height of
grass and types of grass being mowed.
• The average lawn should be cut to approximately 2-1/2
inches during the cool season and to over 3 inches
during hot months. For healthier and better looking
lawns, mow often and after moderate growth.
The direction and speed of movement is controlled by the
forward and reverse drive pedals.
• Start tractor and release parking brake.
• Slowly depress forward (K) or reverse (L) drive pedal to
begin movement. Ground speed increases the further
down the pedal is depressed.
K
•
For best cutting performance, grass over 6 inches
in height should be mowed twice. Make the first cut
relatively high; the second to desired height.
TO ADJUST GAUGE WHEELS (See Fig. 9)
J
Gauge wheels are properly adjusted when they are slightly
off the ground when mower is at the desired cutting height
in operating position. Gauge wheels then keep the deck
in proper position to help prevent scalping in most terrain
conditions.
NOTE: Adjust gauge wheels with tractor on a flat level
surface.
• Adjust mower to desired cutting height (See “TO ADJUST MOWER CUTTING HEIGHT” in this section of
manual).
• With mower in desired height of cut position, gauge
wheels should be assembled so they are slightly off
the ground. Install gauge wheel in appropriate hole.
Tighten securely.
• Repeat for all, installing gauge wheel in same adjustment hole.
L
FIG. 7
TO USE CRUISE CONTROL (J) (See Fig. 7)
The cruise control feature can be used for forward travel
only.
SYSTEM CHARACTERISTICS
The cruise control should only be used while mowing or
transporting on relatively smooth, straight surfaces. Other
conditions such as trimming at slow speeds may cause the
cruise control to disengage. Do not use the cruise control
on slopes, rough terrian or while trimmimg or turning.
• With forward drive pedal depressed to desired speed,
pull cruise control lever (J) up and hold while lifting
your foot off the pedal, then release the lever.
To disengage the cruise control, depress the brake pedal
or tap on forward drive pedal.
TO ADJUST MOWER CUTTING HEIGHT
(See Fig. 8)
FIG. 9
The position of the attachment lift lever (A) determines the
cutting height.
TO OPERATE MOWER
Your tractor is equipped with an operator presence sensing
switch. Any attempt by the operator to leave the seat with
the engine running and the attachment clutch engaged will
shut off the engine. You must remain fully and centrally
positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough,
rolling terrain or hills.
• Select desired height of cut (see "TO ADJUST MOWER
CUTTING HEIGHT")
• Start mower blades by engaging attachment clutch
control.
A
Fig. 8
10
OPERATION
TO STOP MOWER BLADES
•
TO OPERATE ON HILLS
disengage attachment clutch control.
CAUTION: Do not drive up or down
hills with slopes greater than 15° and
do not drive across any slope.
CAUTION: Do not operate the mower
without either the entire grass catcher, on
mowers so equipped, or the deflector shield
(S) in place (See Fig. 10).
•
•
•
S
•
•
•
Choose the slowest speed before starting up or down
hills.
Avoid stopping or changing speed on hills.
If stopping is absolutely necessary, push brake pedal
quickly to brake position and engage parking brake.
To restart movement, slowly release parking brake and
brake pedal.
Slowly depress appropriate drive pedal to slowest setting.
Make all turns slowly.
TO TRANSPORT (See Figs. 3 and 11)
When pushing or towing your tractor, be sure to disengage
transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.
• Raise attachment lift to highest position with attachment
lift control.
• Pull freewheel control out and down into the slot and
release so it is held in the disengaged position.
• Do not push or tow tractor at more than two (2) MPH.
• To reengage transmission, reverse above procedure.
NOTE: To protect hood from damage when transporting
your tractor on a truck or a trailer, be sure hood is closed
and secured to tractor. Use an appropriate means of tying
hood to tractor (rope, cord, etc.).
FIG. 10
REVERSE OPERATION SYSTEM (ROS)
Your tractor is equipped with a Reverse Operation System
(ROS). Any attempt by the operator to travel in the reverse
direction with the attachment clutch engaged will shut off the
engine unless ignition key is placed in the ROS "ON" position.
WARNING: Backing up with the attachment clutch engaged while mowing is strongly discouraged. Turning the
ROS "ON", to allow reverse operation with the attachment
clutch engaged, should only be done when the operator
decides it is necessary to reposition the machine with the
attachment engaged. Do not mow in reverse unless
absolutely necessary.
TRANSMISSION ENGAGED
02828
ROS "ON"
POSITION
ENGINE "ON" POSITION
(NORMAL OPERATING)
TRANSMISSION DISENGAGED
USING THE REVERSE OPERATION SYSTEM Only use if you are certain no children or other bystanders
will enter the mowing area.
• Depress brake pedal all the way down.
• With engine running, turn ignition key counterclockwise
to ROS "ON" position.
• Look down and behind before and while backing.
• Slowly depress reverse drive pedal to start movement.
• When use of the ROS is no longer needed, turn the
ignition key clockwise to engine "ON" position.
FIG. 11
TOWING CARTS AND OTHER ATTACHMENTS
Tow only the attachments that are recommended by and
comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load,
while on a slope, is dangerous. Tires can lose traction with
the ground and cause you to lose control of your tractor.
SERVICE REMINDER/HOUR METER
Service reminder shows the total number of hours the engine
has run and flashes to indicate that the engine or mower
needs servicing. When service is required, the service
reminder will flash for two hours. To service engine and
mower, see the Maintenance section of this manual.
NOTE: Service reminder runs when the ignition key is in
any position but "STOP". For accurate reading, be sure key
remains in the "STOP" position when engine is not running.
11
OPERATION
RESERVE FUEL VALVE OPERATION
(See Fig. 12)
BEFORE STARTING THE ENGINE
CHECK ENGINE OIL LEVEL
1. Raise seat to access reserve fuel valve.
2. In normal operation, valve should be set to primary (as
shown in view)
3. If tractor runs out of fuel, rotate valve handle to reserve.
4. Drive tractor to be refueled.
5. After refueling, return valve to primary position.
The engine in your tractor has been shipped, from the
factory, already filled with summer weight oil.
• Check engine oil with tractor on level ground.
• Remove oil fill cap/dipstick and wipe clean, reinsert the
dipstick and screw cap tight, wait for a few seconds,
remove and read oil level. If necessary, add oil until
“FULL” mark on dipstick is reached. Do not overfill.
• For cold weather operation you should change oil for
easier starting (See “OIL VISCOSITY CHART” in the
Maintenance section of this manual).
• To change engine oil, see the Maintenance section in
this manual.
RESERVE
FUEL VALVE
ADD GASOLINE
•
RESERVE
Fill fuel tank to bottom of filler neck. Do not overfill. Use
fresh, clean, regular unleaded gasoline with a minimum of
87 octane. (Use of leaded gasoline will increase carbon
and lead oxide deposits and reduce valve life). Do not
mix oil with gasoline. Purchase fuel in quantities that can
be used within 30 days to assure fuel freshness.
PRIMARY
Fig. 12
CAUTION: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.
TO START ENGINE (See Fig. 3)
When starting the engine for the first time or if the engine
has run out of fuel, it will take extra cranking time to move
fuel from the tank to the engine.
• Be sure freewheel control is in the transmission engaged
position.
• Sit on seat in operating position, depress brake pedal
and set parking brake.
• Move attachment clutch to “DISENGAGED” position.
• Move throttle control to choke position.
NOTE: Before starting, read the warm and cold starting
procedures below.
• Insert key into ignition and turn key clockwise to “START”
position and release key as soon as engine starts.
Do not run starter continuously for more than fifteen
seconds per minute. If the engine does not start after
several attempts, move throttle control to fast position,
wait a few minutes and try again. If engine still does
not start, move the throttle control back to the choke
position and retry.
IMPORTANT: WHEN OPERATING IN TEMPERATURES
BELOW 32°F(0°C), USE FRESH, CLEAN WINTER GRADE
GASOLINE TO HELP ENSURE GOOD COLD WEATHER
STARTING.
CAUTION: Alcohol blended fuels (called gasohol
or using ethanol or methanol) can attract moisture
which leads to separation and formation of acids
during storage. Acidic gas can damage the fuel
system of an engine while in storage. To avoid
engine problems, the fuel system should be emptied
before storage of 30 days or longer. Drain the gas
tank, start the engine and let it run until the fuel
lines and carburetor are empty. Use fresh fuel next
season. See Storage Instructions for additional
information. Never use engine or carburetor cleaner
products in the fuel tank or permanent damage
may occur.
12
WARM WEATHER STARTING (50° F and above)
• When engine starts, move the throttle control to the
fast position.
• The attachments and ground drive can now be used. If
the engine does not accept the load, restart the engine
and allow it to warm up for one minute using the choke
as described above.
COLD WEATHER STARTING (50° F and below)
• When engine starts, allow engine to run with the
throttle control in the choke position until the engine
runs roughly, then move throttle control to fast position. This may require an engine warm-up period from
several seconds to several minutes, depending on the
temperature.
OPERATION
MOWING TIPS
AUTOMATIC TRANSMISSION WARM UP
• Before driving the unit in cold weather, the transmission
should be warmed up as follows:
• Be sure the tractor is on level ground.
• Release the parking brake and let the brake slowly
return to operating position.
• Allow one minute for transmission to warm up. This
can be done during the engine warm up period.
• The attachments can also be used during the engine warmup period after the transmission has been warmed up.
NOTE: If at a high altitude (above 3000 feet) or in cold
temperatures (below 32 F) the carburetor fuel mixture may
need to be adjusted for best engine performance. See “TO
ADJUST CARBURETOR” in the Service and Adjustments
section of this manual.
•
•
•
•
Mower should be properly leveled for best mowing
performance. See “TO LEVEL MOWER HOUSING” in
the Service and Adjustments section of this manual.
The left hand side of mower should be used for trimming.
Drive so that clippings are discharged onto the area
that has been cut. Have the cut area to the right of the
machine. This will result in a more even distribution of
clippings and more uniform cutting.
When mowing large areas, start by turning to the right
so that clippings will discharge away from shrubs,
fences, driveways, etc. After one or two rounds, mow
in the opposite direction making left hand turns until
finished (See Fig. 13).
PURGE TRANSMISSION
CAUTION: Never engage or disengage
freewheel lever while the engine is running.
To ensure proper operation and performance, it is recommended that the transmission be purged before operating
tractor for the first time. This procedure will remove any
trapped air inside the transmission which may have developed during shipping of your tractor.
FIG. 13
IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE
REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD
BE PURGED AFTER REINSTALLATION BEFORE OPERATING
THE TRACTOR.
•
1. Place tractor safely on a level surface - that is clear
and open - with engine off and parking brake set.
2. Disengage transmission by placing freewheel control
in disengaged position (See “TO TRANSPORT” in this
section of manual).
3. Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position.
Disengage parking brake
•
•
•
CAUTION: At any time, during step 4, there
may be movement of the drive wheels.
4. Depress forward drive pedal to full forward position,
hold for five (5) seconds and release pedal. Depress
reverse drive pedal to full reverse position, hold for five
(5) seconds and release pedal. Repeat this procedure
three (3) times.
5. Shut- off engine and set parking brake.
6. Engage transmission by placing freewheel control in
engaged position (See “TO TRANSPORT” in this section of manual).
7. Sitting in the tractor seat, start engine. After the engine
is running, move throttle control to half (1/2) speed.
Disengage parking brake.
8. Drive tractor forward for approximately five feet then
backwards for five feet. Repeat this driving procedure
three times.
Your transmission is now purged and now ready for normal
operation.
13
If grass is extremely tall, it should be mowed twice to
reduce load and possible fire hazard from dried clippings. Make first cut relatively high; the second to the
desired height.
Do not mow grass when it is wet. Wet grass will plug
mower and leave undesirable clumps. Allow grass to
dry before mowing.
Always operate engine at full throttle when mowing to assure better mowing performance and proper
discharge of material. Regulate ground speed by
selecting a low enough gear to give the mower cutting
performance as well as the quality of cut desired.
When operating attachments, select a ground speed
that will suit the terrain and give best performance of
the attachment being used.
MAINTENANCE
MAINTENANCE
SCHEDULE
BEFORE
EACH
USE
EVERY
8
HOURS
EVERY
25
HOURS
EVERY
50
HOURS
EVERY
100
HOURS
EVERY
SEASON
BEFORE
STORAGE
Check Brake Operation
T
R
A
C
T
0
R
Check Tire Pressure
Check Operator Presence & ROS Systems
Check for Loose Fasteners
Check/Replace Mower Blades
3
Lubrication Chart
Check Battery Level
4
Clean Battery and Terminals
Check Transaxle Cooling
Check Mower Levelness
Check V-Belts
Check Engine Oil Level
Change Engine Oil (with oil filter)
E
N
G
I
N
E
1,2
Change Engine Oil (without oil filter)
1,2
Clean Air Filter
2
Clean Air Screen
2
Inspect Muffler/Spark Arrester
Replace Oil Filter (If equipped)
1, 2
Clean Engine Cooling Fins
2
Replace Spark Plug
Replace Air Filter Paper Cartridge
2
Replace Fuel Filter
1 - Change more often when operating under a heavy load or in high ambient temperatures.
3 - Replace blades more often when mowing in sandy soil.
2 - Service more often when operating in dirty or dusty conditions.
4 - Not required if equipped with maintenance-free battery.
GENERAL RECOMMENDATIONS
LUBRICATION CHART
The warranty on this tractor does not cover items that have
been subjected to operator abuse or negligence. To receive
full value from the warranty, operator must maintain tractor
as instructed in this manual.
Some adjustments will need to be made periodically to
properly maintain your tractor.
At least once a season, check to see if you should make
any of the adjustments described in the Service and
Adjustments section of this manual.
• At least once a year you should replace the spark plug,
clean or replace air filter, and check blades and belts
for wear. A new spark plug and clean air filter assure
proper air-fuel mixture and help your engine run better
and last longer.
➀ SPINDLE ZERK
➀ SPINDLE ZERK
➀ FRONT
➀ FRONT
WHEEL
BEARING
ZERK
WHEEL
BEARING
ZERK
➀ STEERING
➁ ENGINE
SECTOR
GEAR
TEETH
BEFORE EACH USE
•
•
•
•
•
Check engine oil level.
Check brake operation.
Check tire pressure.
Check operator presence and ROS systems for proper
operation.
Check for loose fasteners.
01965
➀
➁
14
General Purpose Grease
Refer to Maintenance “ENGINE” Section
IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS
WHICH HAVE SPECIAL NYLON BEARINGS. VISCOUS
LUBRICANTS WILL ATTRACT DUST AND DIRT THAT WILL
SHORTEN THE LIFE OF THE SELF-LUBRICATING BEARINGS.
IF YOU FEEL THEY MUST BE LUBRICATED, USE ONLY A DRY,
POWDERED GRAPHITE TYPE LUBRICANT SPARINGLY.
MAINTENANCE
TRACTOR
BLADE CARE
For best results mower blades must be kept sharp. Replace
bent or damaged blades.
Always observe safety rules when per form ing any
maintenance.
CAUTION: Use only a replacement blade approved by the manufacturer of your tractor.
Using a blade not approved by the manufacturer of your tractor is hazardous, could
damage your tractor and void your warranty.
BRAKE OPERATION
If tractor requires more than five (5) feet to stop at highest
speed in highest gear on a level, dry concrete or paved
surface, then brake must be checked and adjusted. (See
“TO CHECK BRAKE” in the Service and Adjustments
section of this manual).
BLADE REMOVAL (See Fig. 15)
TIRES
• Maintain proper air pressure in all tires (See the sides
of tires for proper PSI).
• Keep tires free of gasoline, oil, or insect control
chemicals which can harm rubber.
• Avoid stumps, stones, deep ruts, sharp objects and
other hazards that may cause tire damage.
NOTE: To seal tire punctures and prevent flat tires due
to slow leaks, tire sealant may be purchased from your
local parts dealer. Tire sealant also prevents tire dry rot
and corrosion.
• Raise mower to highest position to allow access to blades.
NOTE: Protect your hands with gloves and/or wrap blade
with heavy cloth.
• Remove blade bolt by turning counterclockwise.
• Install new or resharpened blade with stamped "THIS
SIDE UP" facing deck and mandrel assembly.
IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE
IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.
•
IMPORTANT: SPECIAL BLADE BOLT HEAT TREATED.
OPERATOR PRESENCE SYSTEM AND REVERSE
OPERATION SYSTEM (ROS) (See Fig. 14)
Be sure operator presence and reverse operation systems
are working properly. If your tractor does not function as
described, repair the problem immediately.
• The engine should not start unless the brake pedal is
fully depressed, and the attachment clutch control is
in the disengaged position.
MANDREL ASSEMBLY
BLADE
BLADE BOLT
(SPECIAL)
CHECK OPERATOR PRESENCE SYSTEM
• When the engine is running, any attempt by the operator
to leave the seat without first setting the parking brake
should shut off the engine.
• When the engine is running and the attachment clutch
is engaged, any attempt by the operator to leave the
seat should shut off the engine.
• The attachment clutch should never operate unless
the operator is in the seat.
STAR
CENTER HOLE
BATTERY
Fig. 15
Your tractor has a battery charging system which is sufficient
for normal use. However, periodic charging of the battery
with an automotive charger will extend its life.
• Keep battery and terminals clean.
• Keep battery bolts tight.
• Keep small vent holes open.
• Recharge at 6-10 amperes for 1 hour.
NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.
CHECK REVERSE OPERATION (ROS) SYSTEM
• When the engine is running with the ignition switch in
the engine "ON" position and the attachment clutch
engaged, any attempt by the operator to shift into
reverse should shut off the engine.
• When the engine is running with the ignition switch
in the ROS "ON" position and the attachment clutch
engaged, any attempt by the operator to shift into
reverse should NOT shut off the engine.
02828
ROS "ON"
POSITION
Install and tighten blade bolt securely (45-55 Ft. Lbs.
torque).
ENGINE "ON" POSITION
(NORMAL OPERATING)
Fig. 14
15
TO CLEAN BATTERY AND TERMINALS
Corrosion and dirt on the battery and terminals can cause
the battery to “leak” power.
• Raise seat.
• Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor.
• Rinse the battery with plain water and dry.
• Clean terminals and battery cable ends with wire brush
until bright.
• Coat terminals with grease or petroleum jelly.
• Reinstall battery (See “REPLACING BATTERY" in the
SERVICE AND ADJUSTMENTS section of this manual).
MAINTENANCE
V-BELTS
TO CHANGE ENGINE OIL (See Figs. 16 & 17)
Check V-belts for deterioration and wear after 100 hours
of operation and replace if necessary. The belts are not
adjustable. Replace belts if they begin to slip from wear.
Determine temperature range expected before oil change.
All oil must meet API service classification SG-SL.
• Be sure tractor is on level surface.
• Oil will drain more freely when warm.
• Catch oil in a suitable container.
• Remove oil fill cap/dipstick. Be careful not to allow dirt
to enter the engine when changing oil.
• Remove yellow cap from end of drain valve and install
the drain tube onto the fitting.
TRANSAXLE MAINTENANCE
The transmission fan and cooling fins should be kept clean
to assure proper cooling.
Do not attempt to clean fan or transmission while engine
is running or while the transmission is hot. To prevent possible damage to seals, do not use high pressure water or
steam to clean transmission.
• Inspect cooling fan to be sure fan blades are intact and
clean.
• Inspect cooling fins for dirt, grass clippings and other
materials. To prevent damage to seals, do not use compressed air or high pressure sprayer to clean cooling fins.
OIL DRAIN VALVE
CLOSED AND
LOCKED
POSITION
02
3
46
TRANSAXLE PUMP FLUID
The transaxle was sealed at the factory and fluid maintenance is not required for the life of the transaxle. Should
the transaxle ever leak or require servicing, contact your
nearest authorized service center/department.
YELLOW
CAP
ENGINE
FIG. 17
LUBRICATION
•
Only use high quality detergent oil rated with API service
classification SG-SL. Select the oil’s SAE viscosity grade
according to your expected operating temperature.
•
•
SAE VISCOSITY GRADES
•
SAE 30
5W-30
-20
F
C
-30
DRAIN
TUBE
0
-20
30
-10
32
0
40
10
20
•
100
80
60
30
40
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
•
FIG. 16
NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)
improve starting in cold weather, they will result in increased
oil consumption when used above 32°F. Check your engine
oil level more frequently to avoid possible engine damage
from running low on oil.
Change the oil after every 50 hours of operation or at least
once a year if the tractor is not used for 50 hours in one year.
Check the crankcase oil level before starting the engine
and after each eight (8) hours of operation. Tighten oil fill
cap/dipstick securely each time you check the oil level.
Unlock drain valve by pushing inward and turning
counterclockwise.
To open, pull out on the drain valve.
After oil has drained completely, close and lock the
drain valve by pushing inward and turning clockwise
until the pin is in the locked position as shown.
Remove the drain tube and replace the cap onto to the
bottom fitting of the drain valve.
Refill engine with oil through oil fill dipstick tube. Pour
slowly. Do not overfill. For approximate capacity see
“PRODUCT SPECIFICATIONS” section of this manual.
Use gauge on oil fill cap/dipstick for checking level.
Be sure dipstick cap is tightened securely for accurate
reading. Keep oil at “FULL” line on dipstick. Tighten
cap onto the tube securely when finished.
ENGINE OIL FILTER
Replace the engine oil filter every season or every other oil
change if the tractor is used more than 100 hours in one year.
CLEAN AIR SCREEN
Air screen must be kept free of dirt and chaff to prevent
engine damage from overheating. Clean with a wire brush
or compressed air to remove dirt and stubborn dried gum
fibers.
AIR FILTER
Your engine will not run properly using a dirty air filter.
Service air cleaner more often under dusty conditions.
See Engine Manual.
16
MAINTENANCE
ENGINE COOLING SYSTEM
DECK WASHOUT PORT (See Fig. 19)
To ensure proper cooling, make sure the grass screen,
cooling fins, and other external surfaces of the engine are
kept clean at all times.
Every 100 hours of operation (more often under extremely
dusty, dirty conditions), remove the blower housing and
other cooling shrouds. Clean the cooling fins and external
surfaces as necessary. Ensure the cooling shrouds are
reinstalled.
NOTE: Operating the engine with a blocked grass screen,
dirty or plugged cooling fins, and/or cooling shrouds removed
will cause engine damage due to overheating.
Your tractor’s deck is equipped with a washout port on
its surface as part of its deck wash system. It should be
utilized after each use.
1. Drive the tractor to a level, clear spot on your lawn, near
enough to a water spigot for your garden hose to reach.
IMPORTANT: Make certain the tractor’s discharge chute is
directed AWAY from your house, garage, parked cars, etc.
Remove bagger chute or mulch cover if attached.
2. Make sure the PTO (Blade Engage) is not engaged,
set the parking brake, and stop the engine.
3. Thread the nozzle adapter (packaged with your tractor’s
Operator’s Manual) onto the end of your garden hose.
4. Pull back the lock collar of the nozzle adapter and push
the adapter onto the deck washout port at the left end
of the mower deck. Release the lock collar to lock the
adapter on the nozzle.
MUFFLER
Inspect and replace corroded muffler and spark arrester (if
equipped) as it could create a fire hazard and/or damage.
SPARK PLUGS
HOSE
Replace spark plugs at the beginning of each mowing
season or after every 100 hours of operation, whichever
occurs first. Spark plug type and gap setting are shown in
“PRODUCT SPECIFICATIONS” section of this manual.
NOZZLE ADAPTER
WASHOUT
PORT
IN-LINE FUEL FILTER (See Fig. 18)
The fuel filter should be replaced once each season. If fuel
filter becomes clogged, obstructing fuel flow to carburetor,
replacement is required.
• With engine cool, remove filter and plug fuel line sections.
• Place new fuel filter in position in fuel line with arrow
pointing towards carburetor.
• Be sure there are no fuel line leaks and clamps are
properly positioned.
• Immediately wipe up any spilled gasoline.
Fig. 19
IMPORTANT: Tug hose ensuring connection is secure.
5. Turn the water on.
6. While sitting in the operator’s position on the tractor,
re-start the engine and place the throttle lever in the
Fast " " position.
IMPORTANT: Recheck the area making certain the area
is clear.
7. Move the tractor’s PTO (Blade Engage) to the ON
position. Remain in the operator’s position with the
cutting deck engaged until the deck is cleaned.
8. Move the tractor’s PTO (Blade Engage) to the OFF
position. Turn the ignition key to the STOP position to
turn the tractor’s engine off. Turn the water off.
9. Pull back the lock collar of the nozzle adapter to disconnect the adapter from the nozzle washout port.
10. Move the tractor to a dry area, preferably a concrete or
paved area. Engage the mower deck PTO to remove excess water and to help dry before putting the tractor away.
CLAMP
FUEL FILTER
FIG. 18
CLEANING
•
Clean engine, battery, seat, finish, etc. of all foreign
matter.
• Keep finished surfaces and wheels free of all gasoline,
oil, etc.
• Protect painted surfaces with automotive type wax.
We do not recommend using a garden hose or pressure
washer to clean your tractor unless the engine and transmission are covered to keep water out. Water in engine or
transmission will shorten the useful life of your tractor. Use
compressed air or a leaf blower to remove grass, leaves
and trash from tractor and mower.
•
•
17
WARNING: A broken or missing washout
fitting could expose you or others to
thrown objects from contact with the blade.
Replace broken or missing washout fitting
immediately, prior to using mower again.
Plug any holes in mower with bolts and locknuts.
SERVICE AND ADJUSTMENTS
WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:
• Depress brake pedal fully and set parking brake.
• Place attachment clutch in “DISENGAGED” position.
• Turn ignition key to “STOP” and remove key.
• Make sure the blades and all moving parts have completely stopped.
• Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.
TO REMOVE MOWER (See Fig. 20))
•
•
•
•
•
•
TO INSTALL MOWER (See Figs. 20-25)
Place attachment clutch in “DISENGAGED” position.
Lower attachment lift lever to its lowest position.
Remove mower belt from electric clutch pulley (M).
Disconnect front link (E) from mower - remove retainer
spring and washer.
Go to either side of mower and disconnect mower
suspension arm (A) from chassis and rear lift link (C)
from rear mower bracket (D) - remove retainer springs
and washers.
Go to other side of mower and disconnect the suspension arm and rear lift link.
Be sure tractor is on level surface and engage parking
brake.
• Lower attachment lift lever to its lowest position.
CAUTION: Lift lever is spring loaded.
Have a tight grip on lift lever, lower it
slowly and engage in lowest position.
NOTE: Be sure mower side suspension arms (A) are pointing forward before sliding mower under tractor.
• Slide mower under tractor until it is centered under
tractor.
CAUTION: After rear lift links are disconnected, the attachment lift lever
will be spring loaded. Have a tight grip
on lift lever when changing position of
the lever.
•
Slide mower out from under right side of tractor.
B
A
C
D
18
FIG. 20
F
E
M
SERVICE AND ADJUSTMENTS
•
•
ATTACH MOWER SIDE SUSPENSION ARMS (A) TO
CHASSIS - Position hole in arm over pin (B) on outside
of tractor chassis and secure with retainer spring.
Repeat on opposite side of tractor.
•
•
ATTACH FRONT LINK (E) - Work from left side of tractor. Insert rod end of link assembly through front hole
in tractor front suspension bracket (F).
Insert end of link (E) into hole in front mower bracket
(H) and secure with washer and retainer spring (J).
A
E
B
J
F
H
FIG. 21
•
ATTACH REAR LIFT LINKS (C) - Lift rear corner of
mower and position slot in link assembly over pin on
rear mower bracket (D) and secure with washer and
retainer spring.
•
FIG. 23
Install belt onto electric clutch pulley (M).
M
C
FIG. 24
IMPORTANT: CHECK BELT FOR PROPER ROUTING
IN ALL MOWER PULLEY GROOVES.
• Raise attachment lift lever to highest position.
• If necessary, adjust gauge wheels before operating
mower as shown in the Operation section of this manual.
D
FIG. 22
B
A
C
D
19
FIG. 25
F
E
M
SERVICE AND ADJUSTMENTS
TO LEVEL MOWER
•
If adjustment is necessary, see step in Visual Adjustment instructions above.
• Recheck measurements, adjust if necessary until both
sides are equal.
FRONT-TO-BACK ADJUSTMENT (See Figs. 28 & 29)
IMPORTANT: Deck must be level side-to-side.
To obtain the best cutting results, the mower blades should
be adjusted so the front tip is 1/8" to 1/2" lower than the
rear tip when the mower is in its highest position.
Make sure tires are properly inflated to the PSI shown on
tires. If tires are over or under inflated, it may affect the
appearance of your lawn and lead you to think the mower
is not adjusted properly.
VISUAL SIDE-TO-SIDE ADJUSTMENT (See Fig. 26)
• With all tires properly inflated and if your lawn appears
unevenly cut, determine which side of mower is cutting
lower.
• With a 3/4" or adjustable wrench, turn lift link adjustment nut (A) to the left to lower LH side of mower, or,
to the right to raise LH side of mower.
CAUTION: Blades are sharp. Protect
your hands with gloves and/or wrap
blade with heavy cloth.
•
•
A
Raise mower to highest position.
Position blade so the tip is pointing straight forward.
Measure distance (B) to the ground at front and rear
tip of the blade.
B
B
FIG. 28
•
Turn nut left
to lower mower
Turn nut right
to raise mower
•
02948
FIG. 26
NOTE: Each full turn of adjustment nut will change mower
height about 3/16".
• Test your adjustment by mowing some uncut grass
and visually checking the appearance. Readjust, if
necessary, until you are satisfied with the results.
•
If front tip of blade is not 1/8" to 1/2" lower than the rear
tip, go to the front of tractor.
With an 11/16" or adjustable wrench, loosen jam nut A
several turns to clear adjustment nut B.
With a 3/4" or adjustable wrench, turn front link adjustment nut (B) clockwise (ltighten) to raise the front of
mower, or, counterclockwise (loosen) to lower the front
mower.
PRECISION SIDE-TO-SIDE ADJUSTMENT (See Fig. 27)
• With all tires properly inflated, park tractor on level
ground or driveway.
B
A
CAUTION: Blades are sharp. Protect
your hands with gloves and/or wrap
blade with heavy cloth.
•
•
Raise mower to its highest position.
At both sides of mower, position blade at side and
measure the distance (A) from bottom edge of blade
to the ground. The distance should be the same on
both sides.
LOOSEN JAM NUT A FIRST
FIG. 29
02966
NOTE: Each full turn of the adjustment nut will change
mower height about 1/8".
• Recheck measurements, adjust if necessary until front
tip of blade is 1/8" to 1/2" lower than the rear tip.
• Hold adjustment nut in position with wrench and tighten
jam nut securely against adjustment nut.
A
A
LOOSEN
ADJUST NUT
B TO LOWER
MOWER
TIGHTEN ADJUST
NUT B TO RAISE
MOWER
02950
FIG. 27
20
SERVICE AND ADJUSTMENTS
TO REPLACE MOWER BLADE DRIVE BELT
(See Fig. 30)
•
Pull belt slack toward rear of tractor. Carefully remove
belt upwards from transmission input pulley and over
cooling fan blades (F).
• Remove belt downward from engine pulley and
around electric clutch (G).
• Slide belt toward rear of tractor, off the steering plate
(H) and remove from tractor.
BELT INSTALLATION -
MOWER DRIVE BELT REMOVAL
• Park tractor on a level surface. Engage parking
brake.
• Lower attachment lift lever to its lowest position.
• Remove any dirt or grass clippings which may have
accumulated around mandrels and entire upper deck
surface.
• Remove belt from electric clutch pulley (M), both mandrel pulleys (R) and all idler pulleys (V).
•
•
MOWER DRIVE BELT INSTALLATION
• Install belt around all mandrel pulleys (R) and around
idler pulleys (V) as shown.
• Install belt onto electric clutch pulley (M).
IMPORTANT: Check belt for proper routing in all mower
pulley grooves.
• Raise attachment lift lever to highest position.
•
•
•
•
V
•
•
M
•
Install new belt from tractor rear to front, over the steering plate (H) and above clutch brake pedal shaft (J).
Pull belt toward front of tractor and roll belt around
electric clutch and onto engine pulley (G).
Pull belt toward rear of tractor. Carefully work belt
down around transmission cooling fan and onto the
input pulley (F). Be sure belt is inside the belt keeper.
Install belt on centerspan idler (E).
Install belt through stationary idler (C) and clutching
idler (D).
Reinstall anti-rotation link (B) on right side of tractor.
Tighten securely.
Reconnect clutch harness (A).
Make sure belt is in all pulley grooves and inside all
belt guides and keepers.
Install mower (See “TO INSTALL MOWER” section in
this manual).
R
G
R
FIG. 30
H
B
TO REPLACE MOTION DRIVE BELT
(See Fig. 31)
A
Park the tractor on level surface. Engage parking brake.
For assistance, there is a belt installation guide decal on
bottom side of left footrest.
C
J
D
BELT REMOVAL •
Remove mower (See “TO REMOVE MOWER” section
in this manual).
NOTE: Observe entire motion drive belt and position of all
belt guides and keepers.
•
•
•
•
E
Disconnect clutch wire harness (A).
Remove anti-rotation link (B) on right side of tractor.
Remove belt from stationary idler (C) and clutching
idler (D).
Remove belt from centerspan idler (E).
F
02953
electric
21
FIG. 31
SERVICE AND ADJUSTMENTS
TO CHECK BRAKE
TO START ENGINE WITH A WEAK BATTERY
(See Fig. 33)
If tractor requires more than five (5) feet to stop at highest
speed in highest gear on a level, dry concrete or paved
surface, then brake must be serviced.
You may also check brake by:
• Park tractor on a level, dry concrete or paved surface,
depress brake pedal all the way down and engage
parking brake.
• Disengage transmission by placing freewheel control
in “transmission disengaged” position. Pull freewheel
control out and into the slot and release so it is held in
the disengaged position.
The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate,
then the brake needs to be serviced. Contact a qualified
service center.
WARNING: Lead-acid batteries generate explosive gases. Keep sparks,
flame and smoking materials away from
batteries. Always wear eye protection
when around batteries.
If your battery is too weak to start the engine, it should be
recharged. (See "BATTERY" in the MAINTENANCE section of this manual).
If “jumper cables” are used for emergency starting, follow
this procedure:
IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12
VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12
VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO
START OTHER VEHICLES.
FRONT WHEEL TOE-IN/CAMBER
TO ATTACH JUMPER CABLES • Connect one end of the RED cable to the POSITIVE
(+) terminal of each battery(A-B), taking care not to
short against tractor chassis.
• Connect one end of the BLACK cable to the NEGATIVE
(-) terminal (C) of fully charged battery.
• Connect the other end of the BLACK cable (D) to good
chassis ground, away from fuel tank and battery.
Your new tractor front wheel toe-in and camber is set at the
factory and is normal. The front wheel toe-in and camber
are not adjustable. If damage has occurred to affect the
factory set front wheel toe-in or camber, contact a qualified
service center.
TO REMOVE WHEEL FOR REPAIRS
(See Fig. 32)
•
•
Block up axle securely.
Remove axle cover, retaining ring and washers to allow
wheel removal (rear wheel contains a square key - Do
not lose).
• Repair tire and reassemble.
• On rear wheels only: align grooves in rear wheel hub
and axle. Insert square key.
• Replace washers and snap retaining ring securely in
axle groove.
• Replace axle cover.
NOTE: To seal tire punctures and prevent flat tires due
to slow leaks, tire sealant may be purchased from your
local parts dealer. Tire sealant also prevents tire dry rot
and corrosion.
RETAINING
RING
TO REMOVE CABLES, REVERSE ORDER • BLACK cable first from chassis and then from the fully
charged battery.
• RED cable last from both batteries.
WEAK OR
DEAD BATTERY
FULLY CHARGED
BATTERY
FIG. 33
WASHERS
AXLE
COVER
SQUARE KEY (REAR
WHEEL ONLY)
FIG. 32
22
SERVICE AND ADJUSTMENTS
REPLACING BATTERY (See Fig. 34)
TO REMOVE HOOD AND GRILL ASSEMBLY
(See Fig. 35)
WARNING: Do not short battery terminals by allowing a wrench or any other
object to contact both terminals at the
same time. Before connecting battery,
remove metal bracelets, wristwatch
bands, rings, etc. Positive terminal
must be connected first to prevent
sparking from accidental grounding.
•
•
•
•
•
•
•
•
•
•
•
•
Raise hood.
Unsnap headlight wire connector.
Stand in front of tractor. Grasp hood at sides, tilt toward
engine and lift off of tractor.
To replace, reverse above procedure.
Lift hood to raised position.
Remove terminal cover.
Disconnect BLACK battery cable then RED battery
cable and carefully remove battery from tractor.
Install new battery with terminals in same position as
old battery.
Reinstall terminal cover.
First connect RED battery cable to positive (+) battery
terminal with bolt and nut as shown. Tighten securely.
Connect BLACK grounding cable to negative (-) battery
terminal with remaining bolt and nut. Tighten securely
Close hood.
HOOD
HEADLIGHT
WIRE
CONNECTOR
02778
NEGATIVE
(BLACK)
CABLE
TERMINAL
COVER
FIG. 35
TRANSMISSION
POSITIVE
(RED)
CABLE
REMOVAL/REPLACEMENT
Should your transmission require removal for service or
replacement, it should be purged after reinstallation and
before operating the tractor. See “PURGE TRANSMISSION”
in the Operation section of this manual.
Fig. 34
ENGINE
TO REPLACE HEADLIGHT BULB
•
•
•
•
TO ADJUST THROTTLE CONTROL CABLE
Raise hood.
Pull bulb holder out of the hole in the backside of the
grill.
Replace bulb in holder and push bulb holder securely
back into the hole in the backside of the grill.
Close hood.
The throttle control has been preset at the factory and
adjustment should not be necessary. If adjustment is necessary, see engine manual.
TO ADJUST CHOKE CONTROL
The choke control has been preset at the factory and adjustment should not be necessary. If adjustment is necessary,
see engne manual.
INTERLOCKS AND RELAYS
Loose or damaged wiring may cause your tractor to run
poorly, stop running, or prevent it from starting.
• Check wiring. See electrical wiring diagram in the
Repair Parts section.
TO ADJUST CARBURETOR
Your carburetor is not adjustable. If your engine does not
operate properly due to suspected carburetor problems,
take your tractor to an authorized service center for repair
and/or adjustment.
TO REPLACE FUSE
Replace with 20 amp automotive-type plug-in fuse. The
fuse holder is located behind the dash.
23
STORAGE
ENGINE
Immediately prepare your tractor for storage at the end
of the season or if the tractor will not be used for 30 days
or more.
FUEL SYSTEM
IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS
FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH
AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK
DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT
ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING
ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH
LEADS TO SEPARATION AND FORMATION OF ACIDS DURING
STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM
OF AN ENGINE WHILE IN STORAGE.
WARNING: Never store the tractor with
gasoline in the tank inside a building
where fumes may reach an open flame
or spark. Allow the engine to cool before
storing in any enclosure.
TRACTOR
•
Empty the fuel tank by starting the engine and let it run
until the fuel lines and carburetor are empty.
• Never use engine or carburetor cleaner products in
the fuel tank or permanent damage may occur.
• Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage.
Add stabilizer to gasoline in fuel tank or storage container.
Always follow the mix ratio found on stabilizer container.
Run engine at least 10 minutes after adding stabilizer to
allow the stabilizer to reach the carburetor. Do not empty
the gas tank and carburetor if using fuel stabilizer.
Remove mower from tractor for winter storage. When
mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a
clean, dry area.
• Clean entire tractor (See “CLEANING” in the Maintenance section of this manual).
• Inspect and replace belts, if necessary (See belt replacement instructions in the Service and Adjustments
section of this manual).
• Lubricate as shown in the Maintenance section of this
manual.
• Be sure that all nuts, bolts and screws are securely
fastened. Inspect moving parts for damage, breakage
and wear. Replace if necessary.
• Touch up all rusted or chipped paint surfaces; sand
lightly before painting.
ENGINE OIL
Drain oil (with engine warm) and replace with clean engine
oil. (See “ENGINE” in the Maintenance section of this
manual).
BATTERY
CYLINDER(S)
•
•
•
•
•
•
Fully charge the battery for storage.
After a period of time in storage, battery may require
recharging.
To help prevent corrosion and power leakage during
long periods of storage, battery cables should be disconnected and battery cleaned thoroughly (see “TO
CLEAN BATTERY AND TERMINALS” in the Maintenance section of this manual).
After cleaning, leave cables disconnected and place
cables where they cannot come in contact with battery
terminals.
If battery is removed from tractor for storage, do not
store battery directly on concrete or damp surfaces.
•
•
•
Remove spark plug(s).
Pour one ounce of oil through spark plug hole(s) into
cylinder(s).
Turn ignition key to “START” position for a few seconds
to distribute oil.
Replace with new spark plug(s).
OTHER
•
•
•
•
Do not store gasoline from one season to another.
Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems.
If possible, store your tractor indoors and cover it to
give protection from dust and dirt.
Cover your tractor with a suitable protective cover that
does not retain moisture. Do not use plastic. Plastic
cannot breathe which allows condensation to form and
will cause your tractor to rust.
IMPORTANT: NEVER COVER TRACTOR WHILE ENGINE
AND EXHAUST AREAS ARE STILL WARM.
24
TROUBLESHOOTING POINTS
PROBLEM
CAUSE
CORRECTION
Will not start
1.
2.
3.
4.
5.
6.
7.
8.
1.
2.
3.
4.
5.
6.
7.
8.
Out of fuel.
Engine not “CHOKED” properly.
Engine flooded.
Bad spark plug.
Weak or dead battery.
Dirty air filter.
Dirty fuel filter.
Water in fuel.
9.
10.
Loose or damaged wiring.
Carburetor out of adjustment.
9.
10.
11.
Engine valves out of adjustment.
11.
Fill fuel tank.
See “TO START ENGINE” in Operation section.
Wait several minutes before attempting to start.
Replace spark plug.
Recharge or replace battery.
Clean/replace air filter.
Replace fuel filter.
Empty fuel tank and carburetor, refill tank with fresh
gasoline and replace fuel filter.
Check all wiring.
See “To Adjust Carburetor” in Service Adjustments
section.
Contact an authorized service center/department.
1.
2.
3.
4.
5.
6.
7.
Dirty air filter.
Bad spark plug.
Weak or dead battery.
Dirty fuel filter.
Stale or dirty fuel.
Loose or damaged wiring.
Carburetor out of adjustment.
1.
2.
3.
4.
5.
6.
7.
8.
Engine valves out of adjustment.
8.
Clean/replace air filter.
Replace spark plug.
Recharge or replace battery.
Replace fuel filter.
Empty fuel tank and refill tank with fresh, clean gasoline.
Check all wiring.
See “To Adjust Carburetor” in Service Adjustments
section.
Contact an authorized service center/department.
Engine will not turn over
1.
2.
3.
4.
5.
6.
7.
8.
9.
Brake pedal not depressed.
Attachment clutch is engaged.
Weak or dead battery.
Blown fuse.
Corroded battery terminals.
Loose or damaged wiring.
Faulty ignition switch.
Faulty solenoid or starter.
Faulty operator presence switch(es).
1.
2.
3.
4.
5.
6.
7.
8.
9.
Depress brake pedal.
Disengage attachment clutch.
Recharge or replace battery.
Replace fuse.
Clean battery terminals.
Check all wiring.
Check/replace ignition switch.
Check/replace solenoid or starter.
Contact an authorized service center/department.
Engine clicks but will not
start
1.
2.
3.
4.
Weak or dead battery.
Corroded battery terminals.
Loose or damaged wiring.
Faulty solenoid or starter.
1.
2.
3.
4.
Recharge or replace battery.
Clean battery terminals.
Check all wiring.
Check/replace solenoid or starter.
Loss of power
1.
2.
3.
4.
5.
6.
7.
8.
9.
Cutting too much grass/too fast.
Throttle in “CHOKE” position.
Build-up of grass, leaves and trash under mower.
Dirty air filter.
Low oil level/dirty oil.
Faulty spark plug.
Dirty fuel filter.
Stale or dirty fuel.
Water in fuel.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Raise cutting height/reduce speed.
Adjust throttle control.
Clean underside of mower housing.
Clean/replace air filter.
Check oil level/change oil.
Clean and regap or change spark plug.
Replace fuel filter.
Empty fuel tank and refill tank with fresh, clean gasoline.
Empty fuel tank and carburetor, refill tank with fresh
gasoline and replace fuel filter.
Connect and tighten spark plug wire.
Clean engine air screen/fins.
Clean/replace muffler.
Check all wiring.
See “To Adjust Carburetor” in Service Adjustments
section.
Contact an authorized service center/department.
Hard to start
Excessive vibration
10.
11.
12.
13.
14.
Spark plug wire loose.
Dirty engine air screen/fins.
Dirty/clogged muffler.
Loose or damaged wiring.
Carburetor out of adjustment.
10.
11.
12.
13.
14.
15.
Engine valves out of adjustment.
15.
1.
2.
3.
Worn, bent or loose blade.
Bent blade mandrel.
Loose/damaged part(s).
1.
2.
3.
25
Replace blade. Tighten blade bolt.
Replace blade mandrel.
Tighten loose part(s). Replace damaged parts.
TROUBLESHOOTING POINTS
PROBLEM
CAUSE
Engine dies when
tractor is shifted
into reverse
1.
CORRECTION
Reverse operation system
(ROS) is not "ON" while
mower or other attachment
is engaged.
1.
Turn ignition key to
ROS "ON" position.
See Operation section.
Engine continues to run
when operator leaves seat
with attachment clutch
engaged
1.
Faulty operator-safety presence control system.
1.
Check wiring, switches and connections. If not
corrected, contact an authorized service center/
department.
Poor cut - uneven
1.
2.
3.
4.
5.
Worn, bent or loose blade.
Mower deck not level.
Buildup of grass, leaves, and trash under mower.
Bent blade mandrel.
Clogged mower deck vent holes from buildup of
grass, leaves, and trash around mandrels.
1.
2.
3.
4.
5.
Replace blade. Tighten blade bolt.
Level mower deck.
Clean underside of mower housing.
Replace blade mandrel.
Clean around mandrels to open vent holes.
Mower blades will not
rotate
1.
2.
3.
4.
Obstruction in clutch mechanism.
Worn/damaged mower drive belt.
Frozen idler pulley.
Frozen blade mandrel.
1.
2.
3.
4.
Remove obstruction.
Replace mower drive belt.
Replace idler pulley.
Replace blade mandrel.
Poor grass discharge
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Engine speed too slow.
Travel speed too fast.
Wet grass.
Mower deck not level.
Low/uneven tire air pressure.
Worn, bent or loose blade.
Buildup of grass, leaves and trash under mower.
Mower drive belt worn.
Blades improperly installed.
Improper blades used.
Clogged mower deck vent holes from buildup of
grass, leaves, and trash around mandrels.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Place throttle control in “FAST” position.
Shift to slower speed.
Allow grass to dry before mowing.
Level mower deck.
Check tires for proper air pressure.
Replace blade. Tighten blade bolt.
Clean underside of mower housing.
Replace mower drive belt.
Reinstall blades sharp edge down.
Replace with blades listed in this manual.
Clean around mandrels to open vent holes.
Headlight(s) not working
(if so equipped)
1.
2.
3.
4.
5.
Light switch is “OFF”.
Bulb(s) or lamp(s) burned out.
Faulty light switch.
Loose or damaged wiring.
Blown fuse.
1.
2.
3.
4.
5.
Turn light switch “ON”.
Replace bulb(s) or lamp(s).
Check/replace light switch.
Check wiring and connections.
Replace fuse.
Battery will not charge
1.
2.
3.
4.
Bad battery cell(s).
Poor cable connections.
Faulty regulator (if so equipped).
Faulty alternator.
1.
2.
3.
4.
Replace battery.
Check/clean all connections.
Replace regulator.
Replace alternator.
Loss of drive
1.
2.
3.
Freewheel control in “disengaged” position.
Motion drive belt worn, damaged, or broken.
Air trapped in transmission during shipment
or servicing.
1.
2.
3.
Place freewheel control in “engaged” position.
Replace motion drive belt.
Purge transmission.
Engine “backfires” when
turning engine “OFF”
1.
Engine throttle control not set between half and
full speed (fast) position before stopping engine.
1.
Move throttle control between half and full speed
(fast) position before stopping engine.
26
TRACTOR - - MODEL NUMBER 2146XLS (96043006700), PRODUCT NO. 960 43 00-67
SCHEMATIC
SCH13
BATTERY
SOLENOID
STARTER
M
RED
A
RED
FUSE
AMMETER
(OPTIONAL)
BLACK
ELECTRIC CLUTCH
WHITE
S
G
WHITE
C
A1
L
BLACK
WHITE
H
BLACK
M
B
PTO SWITCH
(DISENGAGED)
GRAY
A2
A
D
B
E
CLUTCH/BRAKE
(PEDAL UP)
RED
BLUE
BLACK
REVERSE SWITCH
(NOT IN REVERSE)
BLACK
BLACK
2
BLACK
3
BLACK
BLACK
SEAT SWITCH
(NOT OCCUPIED)
BLACK
BLACK
1
6
87
30
RELAY
85
86
30
87
JUNCTION
CONNECTOR
BLACK /WHITE
BLACK
BLUE
86 87A 85
GRAY
SHORTING
CONNECTOR
CHASSIS
HARNESS
87A
BLACK
C F H
SPARK
PLUGS GAP
(2 PLUGS ON
TWIN CYL. ENGINES)
IGNITION
UNIT
B E G
(OPTIONAL)
A D
HOUR
METER
BLACK
BLUE
PTO SWITCH
FUEL
LINE
(MATING SIDE)
BLACK
BLUE
POWER OUTLET
(OPTIONAL)
BLUE
CHARGING SYSTEM OUTPUT
9-15 AMP DC @ 3600 RPM
FUEL SHUT-OFF
SOLENOID
(IF EQUIPPED)
NOTES
BLACK
12V
REGULATOR
ORANGE
RED
STATOR
28 VOLTS AC @ 3600 RPM (REGULATOR DISCONNECTED)
BROWN
BLACK
LIGHT
SWITCH
HEADLIGHTS
IGNITION SWITCH
POSITION
CIRCUIT
OFF
RUN/OVERRIDE
M+G+A1
B+A1
RUN
START
B+A1
B + S + A1
3
6
2
1
6
3
5
5
2
4
4
1
“MAKE”
L+A2
CHASSIS HARNESS
CONNECTOR
(MATING SIDE)
DASH HARNESS
CONNECTOR
27
WIRING INSULATED CLIPS
NOTE: IF WIRING INSULATED
CLIPS WERE REMOVED FOR
SERVICING OF UNIT, THEY
SHOULD BE RE-INSTALLED TO
PROPERLY SECURE YOUR
WIRING.
NON-REMOVABLE
CONNECTIONS
REMOVABLE
CONNECTIONS
TRACTOR - - MODEL NUMBER 2146XLS (96043006700), PRODUCT NO. 960 43 00-67
ELECTRICAL
T27S
33
22
90
79
30
21
27
2
81
1
24
91
99
100
34
8
27
43
41
40
26
25
55
28
16
0
60
A
M
P 6
S 0
45
71
102
46
29
With 12V Outlet Option
103
105
59
28
42
TRACTOR - - MODEL NUMBER 2146XLS (96043006700), PRODUCT NO. 960 43 00-67
ELECTRICAL
KEY
NO.
PART
NO.
DESCRIPTION
1
2
8
16
21
22
24
25
26
27
28
29
30
33
34
40
41
42
43
45
46
50
55
59
71
79
81
90
91
99
100
102
103
105
532 16 34-65
874 76 04-12
532 18 64-91
532 17 61-38
532 18 37-59
532 00 41-52
532 40 02-53
532 41 28-95
532 17 51-58
873 51 04-00
532 14 54-91
532 40 15-45
532 19 33-50
532 41 19-35
532 11 07-12
532 42 56-75
817 72 04-08
532 13 15-63
532 19 25-07
532 42 52-70
532 42 52-71
532 17 46-51
817 06 05-12
532 40 03-03
532 19 42-76
532 17 52-42
532 40 96-15
532 40 07-24
532 19 02-70
817 67 04-12
819 09 14-16
532 40 44-54
532 42 17-47
532 40 75-68
Battery
Bolt Hex Head 1/4-20 x 3/4
Box Battery
Switch Interlock Push-In
Harness Socket Light w/4152J
Bulb Light
Cable Battery
Cable Starter
Fuse
Nut Keps Hex 1/4-20 unc
Cable, Ground
Switch, Seat
Switch, Ign
Key\Chain
Switch Light / Reset
Harness Ign. Dash
Screw Thd Cut 1/4-20 x 1/2
Cover, Terminal
Solenoid
Ammeter Gauge Round
Gauge Servicereminder Hrmtr
Switch PTO
Screw Thdrol 5/16-18 x 3/4 TYTT
Outlet 12-Volt
Harness Ign.
Socket Asm Bulb Twistlock
Relay Harness Sealed
Cover Terminal
Strap Battery Mount
Screw Hexwsh Thdrol 1/4-20 x 3/4
Washer 9/32 x 7/8 x 16 Ga.
Harness Pigtail
Harness 12-Volt Pigtail
Switch Reverse TT Pedal Control
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
29
TRACTOR - - MODEL NUMBER 2146XLS (96043006700), PRODUCT NO. 960 43 00-67
CHASSIS
15
208
4
3
210
203
212
130
204
206
181
5
214
176
6
6
25
18
14
207
130
209
176
234
211
202
177
178
205
137
150
175
234
176
176
196
221
130
182
162
235
68
36
236
68
130
235
194
36
161
199
213
34
194
37
183
162
218
68
236
68
183
180
68
228
68
189
194
217
165
189
58
52
233
228
189
233
chassis-tex_TEX GT HUSQ_48
30
152
189
TRACTOR - - MODEL NUMBER 2146XLS (96043006700), PRODUCT NO. 960 43 00-67
CHASSIS
KEY
NO.
PART
NO.
DESCRIPTION
3
4
5
6
14
15
18
25
34
36
37
52
58
68
130
137
150
152
161
162
165
175
176
177
178
180
181
182
183
189
532 40 86-06
532 40 50-12
532 40 86-99
532 11 04-52
532 41 10-46
532 19 89-07
532 40 86-07
532 19 89-06
532 19 61-25
817 06 05-12
532 40 18-25
873 68 05-00
532 41 22-81
817 49 05-08
532 41 63-58
532 40 75-90
532 19 85-12
532 19 95-35
532 40 18-26
532 14 24-32
532 19 68-26
532 19 63-04
532 40 07-76
532 19 52-27
532 19 97-82
532 41 50-64
532 40 30-25
532 40 68-59
874 78 05-20
817 00 05-12
Trim, Husq.
Logo
Dash
Nut, Push
Hood
Lens LH
Grille/Lens Asm.
Lens RH
Plate Engine
Screw 5/16-18 x 3/4
Fender
Nut Lock 5/16-18
Drawbar Upper 2 pc Lrg. Fender
Screw Thdrol 5/16-18 x 1/2
Screw 10 x .750 BOS Thread
Bumper Dash
Air Duct
Shield Browning
Window, Fuel
Screw Hex Wsh 1/4 x 1/2 unc
Support Tank Rear
Crossmember
Screw 10-24 x 5/8
Bushing Steering
Cargo Net Asm.
Chassis
Bushing Mtg. Fender Crgo
Dash Lower
Bolt Fin Hex 5/16-18 unc x 1-1/4
Screw 5/16-18 x 3/4
KEY
NO.
PART
NO.
DESCRIPTION
194
196
199
202
203
204
205
206
207
208
209
210
211
212
213
214
217
218
221
228
233
234
235
236
873 90 05-00
532 41 77-78
532 19 82-59
532 40 30-48
532 40 30-76
532 41 66-13
532 40 17-09
532 40 17-11
532 19 71-98
532 19 71-99
532 19 91-30
532 19 91-31
532 19 91-32
532 19 91-33
874 76 05-12
532 19 91-45
532 40 91-67
532 19 63-95
532 19 89-09
532 19 51-61
532 19 65-39
532 40 47-42
532 40 61-29
873 93 05-00
Nut Lock Hex Flange 5/16-18
Console Asm. Deck Lift
Plate Deck Lift
Vent Side Hood RH
Vent Side Hood LH
Vent Top Hood
Skirt Hood Side RH
Skirt Hood Side LH
Bezel RH
Bezel LH
Insert Hex Top RH
Insert Hex Top LH
Insert Hex Bottom RH
Insert Hex Bottom LH
Bolt 5/16-18 x 3/4
Clip Retainer Tinner
Rod Pivot
X-Piece Hood Stop
Reflector LH
Stud Fastner
Bolt, Shoulder
Bumper Hood
Spacer Fender
Nut Lock 5/16-18 unc
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
31
TRACTOR - - MODEL NUMBER 2146XLS (96043006700), PRODUCT NO. 960 43 00-67
DRIVE
207
220
221
74
125
92
213
70
206
116
74
160
209
56
26
216 171
143
197
221
196
125
184
125
35
125
170
42
64
167
52
159
51
160
80
226
285
214
208
284
153
49
185
186
211
125
189
222
187
161
215
163
211
29
50
125
15
159
190
51
52
51
33
210
188
183
2
166
153
17
116
225
230
205
116
2
1
73
drive-tex_K46_pedal_40
183
205
33
73
99
32
230
TRACTOR - - MODEL NUMBER 2146XLS (96043006700), PRODUCT NO. 960 43 00-67
DRIVE
KEY
NO.
PART
NO.
1
532 41 72-13
2
15
17
26
29
33
35
42
49
50
51
52
56
64
70
73
74
80
92
99
116
125
143
153
159
160
161
163
166
167
532 12 35-83
819 13 13-16
532 41 36-78
532 19 96-79
532 40 38-06
812 00 00-01
532 19 95-91
532 12 48-72
872 11 06-14
532 19 43-27
873 90 06-00
532 19 43-26
532 13 09-69
532 19 78-65
532 40 05-30
874 49 05-44
532 14 24-32
532 41 21-70
874 76 05-20
532 41 57-42
873 90 05-00
817 00 05-12
817 49 05-08
532 12 47-88
876 02 04-12
532 16 94-84
532 10 57-09
532 40 10-34
532 19 72-90
532 40 52-57
KEY
NO.
DESCRIPTION
Transaxle, TUFFTORQ K46CR
(Internal parts not available)
Key
Washer 13/32 x 13/16 x 16 Ga.
Spring, Brake
Spring Return Cruise
Rod, Brake
Ring E
Rod, Brake, Park
Cover, Foot Pedal
Bolt
Pulley Idler Flat
Lock Nut 3/8-16
Idler V-Groove 910" Offset
V-Belt, Drive
Shaft Asm. Pedal Brake Control
Console
Bolt Hex Flghd 5/16-18 Gr. 5
Screw
Bracket Strap Torque
Bolt Fin Hex 5/16-18 unc x 1.25
Rod Spring Bypass
Nut Lock Hex Flange 5/16-18
Screw 5/16-18 x 3/4
Screw 5/16-18 x 1/2
Retainer Spring
Pin Cotter 1/8 x 3/4
Retainer Clip
Spring, Return, Clutch
Rod Pedal Control
Nut Push
Latch Brake Parking
170
171
183
184
185
186
187
188
189
190
196
197
205
206
207
208
209
210
211
213
214
215
216
220
221
222
225
226
230
284
285
PART
NO.
532 19 43-22
872 11 06-16
532 13 70-57
532 40 31-18
872 11 06-22
532 19 43-21
819 13 32-10
532 19 43-23
532 19 43-17
532 19 43-18
817 00 06-16
532 19 58-04
532 12 17-48
532 19 78-67
532 19 78-68
532 19 78-69
532 19 95-92
532 40 09-80
532 12 01-83
532 40 31-19
532 41 68-63
532 40 17-23
532 19 61-31
532 19 89-08
532 40 31-87
879 21 20-10
532 40 33-19
532 40 15-64
532 18 89-67
532 41 76-93
532 41 77-65
DESCRIPTION
Keeper Belt Centerspan
Bolt RDHD SQNK 3/8-16 unc x 2
Spacer Split
Handle Parking Brake
Bolt Rdhd Sqnk 3/8-16 x 2-3/4 Gr. 5
Spacer Retainer
Washer
Link Clutch Ground Drive
Bellcrank Ground Drive
Keeper Bellcrank Ground Drive
Screw 3/8-16 x 1
Bracket Clutch Anti-Rotation
Washer
Bracket Mount Latch Cruise
Latch Control Cruise
Gear Sector Control Cruise
Rod Control Cruise
Rocker Asm. Pedal Control
Bearing Nylon
Knob Control Cruise
Pedal Forward
Pedal Reverse
Bracket Pulley Idler
Reflector RH
Retainer Spring Clip Handle
Washer 21/32 x 1-1/4 x 10 Ga.
Keeper Belt Trans.
Bracket Mount Touque
Washer Hardened
Nut U-CHNL 1/4-20 550DP .350 PNL
Screw PHD 1/4-20 Box Drive
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
33
TRACTOR - - MODEL NUMBER 2146XLS (96043006700), PRODUCT NO. 960 43 00-67
ENGINE
87
1
21
116
62
45
22
18
71
69
82
84
15
12
91
79
81
11
28
37
41
42
117
37
70
37
2
85
28
90
9
37
29
SPARK ARRESTER KIT
engine-tex_bs-2cyl_24
34
TRACTOR - - MODEL NUMBER 2146XLS (96043006700), PRODUCT NO. 960 43 00-67
ENGINE
KEY
NO.
PART
NO.
1
------
2
9
11
12
15
18
20
21
22
28
29
37
41
42
45
62
69
70
71
79
81
82
84
85
87
90
91
116
117
532 14 97-23
532 19 43-20
532 40 00-08
532 40 50-97
532 42 28-04
532 19 42-67
532 42 43-41
532 41 63-58
532 19 15-96
532 40 11-35
532 13 71-80
532 12 34-87
532 12 61-97
810 04 07-00
873 51 04-00
532 14 66-29
532 19 24-42
532 19 15-48
532 19 15-49
532 19 24-43
532 14 84-56
532 18 16-54
817 06 06-20
532 17 39-37
537 17 18-77
817 00 06-16
532 18 74-95
532 42 46-59
532 42 08-28
DESCRIPTION
Engine Briggs & Stratton Model
No. 385777
Muffler
Keeper Belt Engine
Clutch
Pulley Engine
Tank Fuel
Cap Asm
Control Throttle
Screw #10 x .750 BOS Thread
Choke
Fuel Line
Spark Arrester Kit
Clamp Hose
Washer 1-1/2 OD x 15/32 ID x .250
Washer Lock 7/16
Nut Keps Hex 1/4-20 unc
Heat Shield
Gasket
Exhaust Tube LH
Exhaust Tube RH
Screw Tube Muffler
Tube Drain Oil Easy
Plug Drain Oil
Screw 3/8-16 x 1-1/4
Bolt Hex 7/16-20 x 4 x Gr. 5-1.5 Thr
Bolt 5/16-18 unc x 3/4 w/Sems
Screw 3/8-16 x 1
Bushing
Knob Soft Touch
Fuel Valve
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
For engine service and replacement parts, call the toll free
number for your engine manufacturer listed below:
Briggs & Stratton
1-800-233-3723
Engine Power Rating Information
The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of Automotive Engineers) code J11940 (Small Engine Power & Torque Rating Procedure), and rating performance has been obtained and
corrected in accordance with SAE J1995 (Revision 2002-5). Actual gross engine power will be lower and is affected by,
among other things, ambient operating conditions and engine-to-engine variability. Given both the wide array of products on which engines are placed and the variety of environmental issues applicable to operating the equipment, the gas
engine will not develop the rated gross power when used in a given piece of power equipment (actual “on-site” or net
horsepower). This difference is due to a variety of factors including, but not limited to, accessories (air cleaner, exhaust,
charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions (temperature, humidity, altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for this Series engine.
35
TRACTOR - - MODEL NUMBER 2146XLS (96043006700), PRODUCT NO. 960 43 00-67
STEERING ASSEMBLY
51
*
*
HUSQ SR
PREM 2
26
45
1
228
*
26
1
21
13
16
63
28
22
64
60
28
9
8
63
19
59
57
7
66
67
2
9
7
8
35
58
6
4
67
6
5
61
14
15
62
8
14
69
68
13
70
15
13
53
steering-tex_special_13_r1
36
TRACTOR - - MODEL NUMBER 2146XLS (96043006700), PRODUCT NO. 960 43 00-67
STEERING ASSEMBLY
KEY
NO.
PART
NO.
1
2
4
5
6
7
8
9
13
14
15
16
19
21
22
26
28
35
45
51
53
57
58
59
60
61
62
63
64
66
67
68
69
70
228
532 41 64-80
532 19 59-68
532 40 30-87
532 40 30-88
532 12 49-31
532 12 17-48
812 00 00-29
532 12 12-32
532 12 17-49
810 04 06-00
873 54 06-00
532 40 82-19
532 19 47-29
532 18 67-37
532 19 48-45
532 41 59-87
817 00 06-12
532 19 47-32
819 18 38-12
873 94 08-00
532 18 89-67
532 40 75-65
532 19 47-47
532 19 47-48
873 97 10-00
532 19 47-40
532 19 47-41
817 00 05-12
532 19 98-49
871 02 07-48
532 19 47-37
873 90 07-00
532 19 91-62
532 19 61-97
532 40 44-84
DESCRIPTION
Wheel, Steering
Axle Asm., Front
Spindle Asm., LH
Spindle Asm., RH
Bearing, Race Thrust Harden
Washer 25/32 x 1-5/8 x 16 Ga.
Ring, Klip #T5304-75
Cap, Spindle
Washer 25/32 x 1-1/4 x 16 Ga.
Washer, Lock Hvy Hlcl Spr 3/8
Nut, Crown Lock 3/8-24 unf
Shaft Steering
Plate Steering
Adapter, Wheel Steering
Bushing, Strg. Blk
Insert, Wheel Steering
Screw 3/8-16 x 3/4
Gear, Sector Plate
Washer 9/16 ID x 2-3/8 OD 12 Ga.
Nut Hex Jam Toplock 1/2-20 unf
Washer Hardened .793 x 1.637 x .060
Bracket Upstop
Bolt Shoulder Sector Pivot CFM
Washer Thrust Sector Steering
Nut Flange Lock 5/8-11
Draglink LH
Draglink, RH
Screw 5/16-18 x 3/4
Retainer Clip Spring Steering
Bolt Hex Fghd 7/16-14 x 3 Serr
Bushing PM Front Axle
Nut Lock Flange 7/16-14 Gr. 5
Washer 1.5 x .505 x .118
Bracket Deck Susp. Front
Decal Wheel Steering
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
37
TRACTOR - - MODEL NUMBER 2146XLS (96043006700), PRODUCT NO. 960 43 00-67
SEAT ASSEMBLY
1
8
8
7
7
8
41
8
40
10
21
6
37
37
44
2
43
21
3
seat-tex_6.5SL_2
KEY
NO.
1
2
3
6
7
8
10
21
PART
NO.
532 42 40-73
532 18 01-66
532 14 06-75
873 80 06-00
532 12 41-81
532 17 18-77
532 19 69-77
532 17 18-52
DESCRIPTION
Seat
Bracket Pivot Fender
Strap, Asm Fender
Nut, Lock W/Ins. 3/8-16 unc
Spring, Seat Cprsn
Bolt 5/16-18 unc x 3/4 w/Sems
Pan, Seat
Bolt, Shoulder 5/16-18
KEY
NO.
PART
NO.
37
40
41
43
44
873 80 05-00
532 19 76-61
532 19 82-00
874 76 06-12
819 13 38-12
DESCRIPTION
Nut, Lock 5/16-18 unc
Handle Slide Seat
Spring Latch Seat
Bolt Fin Hex 3/8-16 unc x 3/4
Washer 13/32 x 2-3/8 x 12 Ga.
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
38
TRACTOR - - MODEL NUMBER 2146XLS (96043006700), PRODUCT NO. 960 43 00-67
MOWER LIFT
87
7
87
90
98
113
10
3
97
100
2
88
97
91
87
91
89
87
lift-tex_16
KEY
NO.
PART
NO.
2
3
7
10
87
88
89
90
91
532 19 52-23
532 19 52-30
532 41 15-55
532 19 63-14
532 19 42-09
532 41 07-10
819 19 19-12
532 19 42-08
532 19 51-81
KEY
NO.
97
98
100
113
DESCRIPTION
Shaft Asm., Lift
Lever Lift Handle
Grip, Lever
Spring Torsion
Pin Cotter 7/16 Bow Tie Lock
Spring Lift Assist
Washer Clear Zinc
Pin Cotter 5/16 Bow Tie Lock
Link Lift Susp Mower Rear
PART
NO.
817 00 06-12
532 19 52-70
873 93 06-00
819 17 19-19
DESCRIPTION
Screw 3/8-16 x 3/4
Link Asm. Susp. Front Mower
Nut Centerlock 3/8-16 unc
Washer 17/32 x1-3/16 x 12 Ga.
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
39
TRACTOR - - MODEL NUMBER 2146XLS (96043006700), PRODUCT NO. 960 43 00-67
MOWER DECK
?TEX?LT?PRED?
40
TRACTOR - - MODEL NUMBER 2146XLS (96043006700), PRODUCT NO. 960 43 00-67
MOWER DECK
KEY PART
NO. NO.
DESCRIPTION
1
2
3
6
8
11
13
14
15
19
21
23
24
25
26
27
29
30
31
32
33
34
36
40
46
55
56
57
59
62
Mower Housing
Cover Mandrel RH
Cover Mandrel LH
Arm Suspension
Bolt/Washer asm 7/16-20 unf
Blade Mower Hi Lift
Shaft Assembly, Mandrel
Housing, Mandrel
Bearing, Ball, Mandrel
Bolt, Shoulder
Nut
Bracket, Deflector
Cap, Sleeve
Spring, Torsion, Deflector
Nut, Push
Shield, Deflector
Rod, Hinge
Screw Thdrol Rolling Wsh Hd
Washer, Spacer
Pulley, Mandrel
Nut, Toplock, Flanged
Bolt Carr Sh. 3/8-16 x 1-1/2 Gr. 5
Pulley, Idler, Flat
Nut, Lock Flg. 3/8-16 unc
Screw
Arm, Idler
Spacer, Retainer
Screw Hexwsh Thd 3/8-16 x 1
Guard, Tuv Idler (94)
Bolt 3/8-16 unc x 2-1/4 Gr. 5
532 42 16-49
532 40 55-07
532 40 55-06
532 19 51-86
532 19 30-03
532 40 53-80
532 19 28-72
532 18 72-81
532 11 04-85
532 19 65-39
873 68 05-00
532 19 25-57
532 10 53-04
532 19 70-26
532 11 04-52
532 40 53-57
532 13 14-91
532 17 39-84
532 18 76-90
532 19 74-73
532 40 02-34
872 11 06-12
532 19 73-79
873 90 06-00
532 13 77-29
532 19 72-49
532 19 90-92
817 00 06-16
532 14 10-43
874 52 06-36
KEY PART
NO. NO.
68
69
116
117
118
119
145
147
188
189
197
198
199
200
241
242
243
244
245
---
532 40 51-43
872 14 05-05
532 19 34-06
532 17 48-73
873 93 06-00
819 13 20-12
532 19 31-97
532 19 72-51
532 19 51-61
873 90 05-00
819 13 13-12
532 40 31-49
532 40 31-50
532 41 35-24
532 15 29-27
532 41 55-98
532 18 86-06
532 12 48-42
819 12 14-14
532 41 64-05
532 19 28-70
--
532 41 82-26
DESCRIPTION
V-Belt
Bolt
Bolt, Shoulder
Wheel, Gauge
Nut Centerlock 3/8-16 unc
Washer 13/32 x 1-1/2 x 11 Ga.
Pulley Idler
Spring Return
Stud Fastener
Nut Lock Hex Flange
Washer 13/32 x 13/16 x 12 Ga.
Baffle Center Front
Baffle Front RH
Washer 13/32 x 1 x 1/2 11 GAHRD
Screw
Washout Port
Wheel Gauge Half Spoked
Bolt Shoulder "A" 2.41. "B" 1.66
Washer 3/8 x 7/8 x 14 Ga.
Coupling Quick Connect
Mandrel Assembly (Includes
housing, shaft assembly, and
bearing only - pulley/nut/washer
and blade bolt/washers not
included)
Replacement Mower, Complete
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
41
TRACTOR - - MODEL NUMBER 2146XLS (96043006700), PRODUCT NO. 960 43 00-67
DECALS
2
5 6
2
3
1
8
9
12 7
KEY
NO.
PART
NO.
1
2
3
5
6
7
8
9
532 41 16-58
532 42 47-89
532 42 56-46
532 42 38-29
532 41 55-44
532 41 86-00
532 17 05-63
532 14 50-05
DESCRIPTION
Decal, Operators
Decal, Emblem
Decal, Emblem Panel SD
Decal, Customer Respons.
Decal, Replacement
Decal, Pedal Husq. Crown
Decal Mower Warn Keep Hand away
Decal, Battery Dnge/Poi
WHEELS AND TIRES
1
2
11 3
4
7
10
5
6
9
8
KEY
NO.
PART
NO.
12
-----
532 16 03-96
532 41 82-77
532 16 69-60
532 40 17-71
532 40 37-73
Decal, Mower V-Belt Schematic
Decal, Deck Air Induct
Decal, Bypass
Pad, Footrest, LH
Pad, Footrest, RH
KEY
NO.
1
2
3
4
5
6
7
8
9
10
11
--
PART
NO.
532 05 91-92
532 06 51-39
532 13 83-36
532 05 99-04
532 17 04-55
532 12 49-57
532 12 49-59
532 17 50-39
532 17 04-56
532 12 49-26
532 13 83-37
532 14 43-34
DESCRIPTION
Cap Valve Tire
Stem Valve
Rim Front Service
Tube Front (Service Item Only)
Tire TM Front 15 x 6.00-6
Fitting Grease (Front Wheel Only)
Bearing Flange (Front Wheel Only)
Cap Axle Blk 1 50 x 1 00
Tire TM Rear 30 x 10.00-8
Tube Rear (Service Item Only)
Rim Asm 8" rear Service
Sealant, Tire (10 oz. Tube)
DESCRIPTION
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
wheel_art_1-tex
42
HUSQVARNA PRODUCT REGISTRATION INFORMATION & WARRANTY STATEMENT
All Husqvarna products can be registered online at www.usa.husqvarna.com quickly and easily regardless of their model year. Click the Support tab,
then click on the Online Product Registration link, and fill out the electronic form and submit. Ask about Husqvarna s extended service plan!
SECTION 1: LIMITED WARRANTY
Husqvarna Professional Products, Inc (“Husqvarna”) warrants the original purchaser the Husqvarna branded product to which this warranty apply (the “Product”) that the Product shall be free from defects in material and workmanship
from the date of purchase for the period of the applicable “Warranty Schedule” of the Product as set forth below. Additional limitations are described in Section 2 through 6, inclusive.
COMMERCIAL /
RENTAL
CONSUMER
PRODUCT CATEGORY
PROFESIONAL
WARRANTY
WARRANTY SCHEDULE* WARRANTY SCHEDULE
SCHEDULE
Reconditioned Products: Reconditioned chainsaws, trimmers, brushcutters, clearing saws, handheld blowers,
backpack blowers, hedge trimmers, and electrical products.
90 Days
N/A
N/A
Chain Saws Lifetime Ignition Warranty (Parts Only). One Year Conditional Crankshaft Warranty for Commercial/Professional use when operated with
2 Years
90 Days
90 Days
100 Series Trimmers, Stick Edgers, Hedge Trimmers
2 Years
1 Year
90 Days
2 Years
1 Year
90 Days
Blowers (Lifetime Ignition Warranty - Parts Only)
2 Years
2 Years
90 Days
Pole Pruners, Pole Saws, Pole Hedge Trimmers (Lifetime Ignition Warranty - Parts Only)
1 Year
1 Year
90 Days
Residential Walk-Behind Mowers, Tillers, LE389 Edger †
2 Years
N/A
N/A
LE475 Edger †
LT, LTH, LS, XLS, GLS, YT, YTH, GT, GTH, 16H, Pro15, 155 ProFlex Series Lawn & Garden Riders and
Residential Zero Turn Mowers †
2 Years
90 Days
90 Days
2 Years
N/A
N/A
3 Years or 600 Hours
1 Year or 600 Hours
90 Days
5 Years or 1,500 Hours
5 Years or 1,500 Hours
90 Days
90 Days
Husqvarna XP 2 cycle oil (Parts & Labor).
Lifetime Ignition Warranty (Parts Only). Lifetime Shaft Warranty.
200 & 300 Series Trimmers, Brushcutters, Clearing Saws, Stick Edgers, Hovering Trimmers & Hedge Trimmers
Lifetime Ignition Warranty (Parts Only) and Lifetime Shaft Warranty apply to these products (excludes Hovering Trimmers).
MZ and EZ Series Zero Turn Riders †
iZ, LZ, BZ Series Zero Turn Riders † (Applies to units factory-equipped with Roll Over Protection System.)
Commercial Walk Mowers † (includes 21” & wide area)
3 Years
3 Years
Commercial Turf Specialty Equipment †
1 Year
1 Year
1 Year
Zero Turn & Commercial Turf Specialty Attachments
2 Years
1 Year
90 Days
Power Cutters (Lifetime Ignition Warranty - Parts Only)
1 Year
90 Days
1 Year (K750 only)
90 Days
Automatic Mower (1 Year Battery Warranty)
2 Years
90 Days
90 Days
Snow Throwers †
2 Years
90 Days
90 Days
Pressure Washers †
2 Years
Generators (Husqvarna s warranty does not cover Engine & Generator Parts, which are warrantied by responsible manufacturer.) †
Grass Catchers & Bumpers Purchased with New Units
2 Years
(2nd Year Parts Only)
2 Years
(Excludes 5525PW)
2 Years – 1365GN only
(2nd Year Parts only)
1 Year
Parts & Accessories Purchased Separately
30 days
2 Year or 2,000 Hour Powertrain & 1 Year or 1,000 Hour Body Warranty
HUV Batteries: 4210E Versions
4 Year Pro-rated
Husqvarna Safety Apparel***
Batteries**** (Consumer Products where applicable)
Replacement Parts, Accessories including Bars and Chains, Tools and Display Items. Emission Control System Components necessary to
comply with CARB-TIER II and EPA Regulations (Excludes components which are part of engine systems manufactured by third part engine manufacturers for
which the purchaser has received a separate warranty with product at time of purchase.)
N/A
Same Warranty As Unit When Purchased with Unit
Spreaders
Husqvarna Utility Vehicles** (Engines/transmissions shall be warrantied through Husqvarna.)
N/A
90-day
1 year
N/A
30 Day Warranty
IR
Part Number 525 88 56-01
† Refer to Section 3 for items not covered by this warranty
*All consumer product use must have been limited to the owner s residence. Warranted for noncommercial, nonprofessional, noninstitutional and nonincome producing use.
**HUV 2 Year or 2,000 Hour Powertrain (The engine assembly, unitized transaxle assembly (gasoline vehicle), motor, and main frame assembly are warranted with respect to parts and labor against defects in material and
workmanship or a period of two years or 2000 hours of operation, whichever first occurs, from the date of purchase.) & 1 Year or 1,000 Hour Body Warranty (All remaining components of the vehicle not specified otherwise and all
other original equipment options and accessories supplied by Husqvarna are warranted with respect to parts and labor against defects in material and workmanship for a period of one year or 1000 hours of operation, whichever first
occurs, from the date of purchase.)
HUV s Gas & Diesel Powered Battery: 0 – 6 months free replacement and 7 – 12 months prorated
HUV s Electric Powered – 4 year or 16,000 Energy Unit Limited Warranty Period
***Husqvarna safety apparel warranty is from the date of the customer s original purchase for defects in material and workmanship. Normal wear, tear or abuse is not covered under warranty. All care and maintenance instructions
must be followed as stated by the manufacturer on the care label. The fit of the protective apparel/boot is not covered under warranty.
****Battery 1 Year prorated limited warranty with 100% replacement during the first 6 months.
Lifetime Warranty (Parts and Labor): All tiller tines and trimmer shafts against breakage. Proof of purchase required.
Lifetime Warranty (“PARTS ONLY” after initial warranty expiration): Ignition coils and modules on handheld product. Proof of purchase required.
SECTION 2: HUSQVARNA S OBLIGATIONS UNDER THE WARRANTY
Husqvarna will repair or replace defective components without charge for parts or labor if a component fails because of a defect in material or workmanship during the warranty period.
SECTION 3: ITEMS NOT COVERED BY THIS WARRANTY
The following items are not covered by this warranty:
(1) Normal customer maintenance items which become worn through normal regular use, including, but not limited to, belts, blades, blade adapters, bulbs, clutches, clutch drums, filters (fuel line, fuel filters, air filters, oil filters),
sprockets, guide bars, lubricants, rewind springs, saw chain, spark plugs, starter ropes and tiller tines;
(2) Natural discoloration of material due to ultraviolet light;
(3) Engine and drive systems not manufactured by Husqvarna; these items are covered by the respective manufacturer s warranty as provided in writing with the product information supplied at the time of purchase; all claims must be
sent to the appropriate manufacturer.
(4) Lawn and garden attachments that are covered by a third party which gives a warranty, all claims for warranty should be sent to the manufacturer.
(5) Commercial or consumer mowing decks with sand abrasion damage.
(6) Emission Control System components necessary to comply with CARB-TIER II and EPA regulations which are manufactured by third party engine manufacturer.
SECTION 4: EXCEPTIONS AND LIMITATIONS
This warranty shall be inapplicable to defects resulting from the following:
(1) Accident, abuse, misuse, negligence and neglect, including stale fuel, dirt, abrasives, moisture, rust, corrosion, or any adverse reaction due to incorrect storage or use habits;
(2) Failure to operate or maintain the unit in accordance with the Owner s/Operator s manual or instruction sheet furnished by Husqvarna;
(3) Alterations or modifications that change the intended use of the product or affects the product s performance, operation, safety, or durability, or causes the product to fail to comply with any applicable laws; or:
(4) Additional damage to parts or components due to continued use occurring after any of the above.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. HUSQVARNA SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THESE PRODUCTS EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE ON THESE PRODUCTS IS LIMITED IN DURATION TO THE WARRANTY PERIOD AS DEFINED IN THE LIMITED WARRANTY STATEMENT. HUSQVARNA RESERVES THE RIGHT TO CHANGE OR
IMPROVE THE DESIGN OF THE PRODUCT WITHOUT NOTICE, AND DOES NOT ASSUME OBLIGATION TO UPDATE PREVIOUSLY MANUFACTURED PRODUCTS.
Some states do not allow the exclusion of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal
rights, and you may also have other rights which vary by state.
SECTION 5: CUSTOMER RESPONSIBILITIES
The product must exhibit reasonable care, maintenance, operation, storage and general upkeep as written in the maintenance section of the Owner s/Operator s manual. Should an operational problem or failure occur, the product
should not be used. Failure caused by continued use is not covered by warranty. Product should be delivered, at owners expense, as is, to an authorized Husqvarna Servicing Retailer for evaluation. Proof of purchase, as explained
in section 6, rests solely with the customer.
SECTION 6: PROCEDURE TO OBTAIN WARRANTY CONSIDERATION
It is the Owner s and Retailer s responsibility to make certain that the Warranty Registration Card is properly filled out and mailed to Husqvarna. This card should be mailed within ten (10) days from the date of purchase in order to
confirm the warranty and to facilitate post-sale service. Proof of purchase must be presented to the authorized Husqvarna retailer in order to obtain warranty service. This proof must include date purchased, model number, serial
number, and complete name and address of the selling retailer. To obtain the benefit of this warranty, the product believed to be defective must be delivered to an authorized Husqvarna retailer in a timely manner, no later than thirty
(30) days from date of the operational problem or failure. The product must be delivered at the owner s expense. Downtime, pick-up and delivery charges are not covered by this warranty. An authorized Husqvarna retailer can be
located by calling 1-800-HUSKY-62 or visiting www.husqvarna.com
Subject to change without notice.
HUSQVARNA 7349 Statesville Road, Charlotte, NC 28269
IR
Part Number 525 88 56-01
532 42 55-92 11.25.08 BAD
Printed in the U.S.A.