Raymarine ST30 Product specifications

Distributed by
Any reference to Raytheon or
RTN in this manual should be
interpreted as Raymarine.
The names Raytheon and RTN
are owned by the
Raytheon Company.
TOP EDGE BLEED
MASK FOR
2 COLOUR
SEATALK
LOGO
ST 30
BIDATA
Operation and
Installation
TOP EDGE BLEED
MASK FOR
2 COLOUR
SEATALK
LOGO
Nautech Limited, Anchorage Park, Portsmouth
P03 5TD, England
Telephone (0705) 693611. Fax (0705) 694642
ST30 Bidata Operation and Installation Handbook
et
Fe
ots
Kn
T
SE
H
PT
DE
RE
ED
ED
E
SP
PL
DIS
AY
E
SP
A
AT
BID
TM
D681
Autohelm and SeaTalk are registered Trade Marks of Nautech Limited
Autohelms policy of continuous improvement and updating may change product specifications
without prior notice
Copyright Nautech 1992
ST30 Bidata Operation and Installation Handbook
Package Contents
The following items are included in the ST30 Bidata package:
1.
ST30 Bidata instrument
2.
Fixing studs (2 off)
3.
Thumb nuts (2 off)
4.
Mounting template
5.
1m power cable
6.
Depth transducer (through hull) with 10m cable and 1/8in spade
connectors
7.
Speed transducer (through hull) with 10m cable and 1/8in spade
connectors (0 to 32 knots)
8.
Instrument cover
9.
Operation and installation handbook
10. High speed paddle wheel (2 to 45 knots)
11. Daisy-chain cable
1
6
7
DEPTH
SPEED
DEPTH
SPEED
RESET
BIDATA
TM
SeaTalk
3
2
SeaTalk
SeaTalk
5
11
8
TM
TM
ST30
9
BIDATA
Operation and
Installation
SeaTalk
ST30 INSTRUMENT
MOUNTING TEMPLATE
2-HOLES
DRILL 5mm
( .197" ) DIA
4
1-HOLE
DRILL 60.3mm
( 2,3/8" ) DIA
10
D680
ST30 Bidata Operation and Installation Handbook
3
Contents
Introduction ....................................................................... 5
Chapter 1: Control Head Installation ................................... 7
1.1 Siting ............................................................................. 7
1.2 Mounting procedure ........................................................ 8
1.3 Power supply (Stand-alone operation) ............................... 9
1.4 Power supply (SeaTalk system) ........................................ 9
1.5 Connection to adjacent ST30 instruments ....................... 10
Chapter 2: Transducer Installation .................................... 11
2.1 Connection to instrument ............................................... 11
2.2 Transducer type ........................................................... 11
Depth ........................................................................... 12
Speed .......................................................................... 12
Speed and depth .......................................................... 12
2.3 Paddlewheel replacement .............................................. 13
2.4 Installation .................................................................... 14
Speed transducer (through hull) ..................................... 14
Siting of depth transducer (Standard through hull) ........... 15
2.5 Cabling ........................................................................ 15
Chapter 3: Fault Finding ................................................... 18
Chapter 4: Maintenance ................................................... 20
4.1 Instrument .................................................................... 20
4.2 Transducer ................................................................... 20
4.3 Cabling ........................................................................ 20
4.4 Advice .......................................................................... 20
Chapter 5: Operation ....................................................... 21
5.1 Depth Key .................................................................... 21
5.2 Speed Key ................................................................... 22
5.3 Light Key ...................................................................... 24
5.4 Alarms ......................................................................... 24
Loss of signal ............................................................... 24
Chapter 6: Calibration ..................................................... 25
6.1 Depth calibration .......................................................... 25
Units selection Ð depth ................................................. 26
Shallow alarm ............................................................... 26
Deep alarm .................................................................. 27
Offset .......................................................................... 29
Exit depth calibration ..................................................... 30
Operation
4
ST30 Bidata Operation and Installation Handbook
Contents (cont.)
6.2 Speed calibration .......................................................... 31
Units selection Ð speed ................................................. 31
Units selection Ð log ..................................................... 32
Exit calibration .............................................................. 32
Log calibration .............................................................. 33
Enter correction factor (CF) ........................................... 34
6.3 Calibration Lock/Unlock ................................................ 35
6.4 Master/Repeater mode ................................................. 37
Chapter 7: Specification .................................................. 39
5
ST30 Bidata Operation and Installation Handbook
Introduction
Designed for above or below deck installation, the ST30 Bidata can be
used as a stand-alone master instrument or set to repeat depth and speed
information from the SeaTalk bus.
The ST30 Bidata will display the following information:
• Water depth
• Shallow water alarm
• Deep water alarm
• Keel/Waterline offset
• Minimum depth
• Boat speed
• Log
• Trip
• Maximum speed
• Average boat speed
• Illumination level
et
Fe
ots
Kn
RE
D
EE
D
EE
SP
T
SE
H
PT
DE
Y
LA
SP
DI
SP
A
AT
BID
TM
D681
6
ST30 Bidata Operation and Installation Handbook
7
Chapter 1: Control Head Installation
Chapter 1: Control Head Installation
42mm (1.65in)
56mm (2.20in)
DEPTH
SPEED
88mm (3.46in)
24mm (1.00in)
BIDATA
TM
110mm (4.33in)
D682
1.1 Siting
The ST30 Bidata instrument may be installed above or below deck where
it is:
• easily read by the helmsman (normally viewed at eye level)
• protected from physical damage
• at least 230mm (9in) from a compass
• at least 500mm (20in) from radio receiving equipment
• accessible from behind for ease of installation and cable running
Notes: To prevent the build-up of moisture, the instrument breathes
through the back cover. The instrument must, therefore, be mounted
where the back cover is protected from direct water.
The rear case is fitted with a foam gasket to form a water-tight seal
between the instrument and the installation face.
ST30 Bidata Operation and Installation Handbook
8
1.2 Mounting procedure
3
6
5
2
4
1
D682a
1 Instrument 2 Fixing studs 3 Thumb nuts 4 Sealing gasket
5 Depth transducer cable 6 Speed transducer cable
1.
Make sure the surface to which the instrument (1) is to be mounted is
smooth and flat.
2.
Use the fitting template (supplied) to mark the centres for the two
fixing holes and the instrument connector boss.
Note: To allow for the fitting of protective covers, adjacent
instruments must have a 6mm (1/4in) gap between them (116mm
centre to centre min.).
3.
Drill two 5mm (0.2in) diameter holes for the fixing studs (2).
4.
Using a 60mm (2 3/8in) diameter cutter, drill a location hole for the
instrument connector boss.
5.
Connect the power supply and transducer cables to the back of the
instrument (1) (see relevant installation sections).
6.
Screw the two fixing studs (2) into the back cover.
7.
Install the instrument (1) and secure with the thumb nuts (3) provided.
9
Chapter 1: Control Head Installation
1.3 Power supply (Stand-alone operation)
Caution: The ST30 Bidata must be connected to a 12V supply only.
+
+
DE
PT
D
EE
SEATALK
H
SP
+
+
5A
+
Red
12v Supply
Screen
–
D683
For stand-alone operation, use the standard 1m cable supplied.
1.
Connect the moulded power plug to either 'SeaTalk' connection on
the rear of the instrument. Run the free end back to the vessel's
distribution panel.
2.
Cut the cable to length and connect the red wire to 12V and the
screen to 0V. Protect the circuit with a 5A fuse/circuit breaker.
1.4 Power supply (SeaTalk system)
The ST30 Bidata can be connected to an existing SeaTalk system using a
Standard SeaTalk Extension or Interface Cable.
Autohelm
Autohelm
Autohelm
Power
Extension Cable
D628
10
ST30 Bidata Operation and Installation Handbook
1.5 Connection to adjacent ST30 Instruments
The ST30 Bidata is supplied with a daisy-chain cable that allows adjacent
ST30 instruments to be linked together. The daisy-chain cable supplies
power to adjacent instruments and allows data to be transmitted and
received via the SeaTalk bus.
The daisy-chain cable plugs into one of the SeaTalk ports on the back
cover.
11
Chapter 2: Transducer Installation
Chapter 2: Transducer Installation
2.1 Connection to instrument
The depth and speed transducers are supplied with 10m (32.5ft) of cable.
These cables are fitted with female spade connectors that plug directly
into the back of the ST30 Bidata instrument.
+
+
DE
PT
H
D
EE
SEATALK
SP
+
Speed
+
Depth
D684
2.2 Transducer type
The ST30 Bidata system is supplied (as standard) with plastic through hull
transducers. These are suitable for use with Glass Reinforced Plastic
(GRP), Steel and Aluminium hulls.
Alternative transducers are available for wooden hull and transom mount
installations.
ST30 Bidata Operation and Installation Handbook
12
Depth
Hull material or
location
Transducer
GRP, Steel, Aluminium Standard through hull
Wood
Bronze (Z118)
GRP, Steel, Aluminium Retractable depth (Z120)
In hull
In hull puck (Z117)
Speed
Hull material or
location
Boat speed Transducer
GRP, Steel, Aluminium Up to
32kts
Standard through
hull
GRP, Steel, Aluminium Up to
45kts
Standard and high
speed paddle
Wood
Up to
45kts
Bronze (Z116)
Transom
Up to
60kts
Transom mount with
bracket (Z119)
Speed and depth
Hull material or
location
Transducer
Transom
Biducer (Z183)
Caution: Plastic through hull transducers must not be used on vessels
with wooden hulls.
Note: The ST30 Speed transducers are fitted with standard paddlewheels
designed for speeds up to 32 knots. For vessels that will exceed this
speed, please refer to section 2.3 which contains instructions on how to
fit the high speed paddlewheel (supplied).
13
Chapter 2: Transducer Installation
2.3 Paddlewheel replacement
If the high speed paddlewheel (supplied) is to be fitted, or the existing
paddlewheel to be replaced, proceed as follows:
1.
Remove the retaining rings (1) and pin (6) from the speed
transducer (3).
2.
Withdraw the speed transducer (3) from the through hull fitting (4).
3.
If replacing a worn paddlewheel and if the vessel is still in the water,
replace the speed transducer (3) with the plug (5).
4.
Remove the pin (6) that retains the paddlewheel (7) in the speed
transducer (3). This is a simple press fit into the transducer housing.
5.
Fit the high speed/replacement paddlewheel (7) to the speed
transducer (3) and retain with the pin (6).
Note: The paddlewheel is correctly orientated when the working (flat)
surfaces of each paddle are facing forwards.
6.
Assemble the speed transducer (3) to the through hull fitting (4) and
secure with the retaining rings (1) and pin (2).
3
6
5
7
8
2
1
4
D587a
ST30 Bidata Operation and Installation Handbook
14
2.4 Installation
The depth and speed transducers are supplied with detailed installation
and maintenance instructions. These instructions, together with following
notes, should be read thoroughly before attempting to install the
transducers.
Speed transducer (through hull)
For accurate speed readings, locate the speed transducer in the shaded
''clear flow' areas as shown.
D587
The transducer should also be:
• ahead of propellers (10% W.L. length minimum)
• at least 150mm (6in) from the keel (with sailing yachts siting should be
forward of the keel)
• near the centreline of the vessel
• clear of other through hull fittings or projections
• have sufficient clearance inside the hull to allow the nut to be fitted
• have 100mm (4in) clearance above the through hull fitting for
withdrawal
Note: The speed transducer can, if required, be shortened. However, new
1/8in spade connectors must be crimped to the shortened cable.
15
Chapter 2: Transducer Installation
Siting of depth transducer (Standard through hull)
The depth transducer must be vertical to within 10°, forward, aft and
athwart ships.
10° Max
D630
2.5 Cabling
Run the transducer cable back to the instrument. Avoid fluorescent lights,
engines, radio transmitting equipment and, in the case of the depth
transducer, avoid the speed transducer cable. The cables should also be
kept clear of the bilgeÕs and be secured at regular intervals.
Note: The depth transducer cable must not be shortened.
Shortening of the cable will affect the performance of the
transducer. For further information, please contact Autohelm or
an authorised Autohelm agent.
ST30 Bidata Operation and Installation Handbook
16
If any of the following transducers are to be used;
• Bronze through hull depth (Z118)
• In hull puck (Z117)
• Retractable depth (Z120)
• Bronze through hull speed (Z116)
• Transom mount speed (Z119)
• Bronze through hull triducer (Z093)
• Transom mount Biducer (Z183)
the following modification must be carried out to the transducer leads.
1.
Using a pair of wire cutters, remove the moulded plug from the end
of cable.
2.
Strip the outer cable back 38mm (1.5in)
3.
Using a pair of cable strippers, remove 10mm (3/8in) of insulation
from each wire.
4.
Using a suitable crimping tool, attach a 1/8in spade connector
(supplied) to each of the wires.
5.
Connect the wires to the instrument in accordance with the following
table.
Transducer type
Colour coding (cable to
unit)
Bronze through hull
(Z118)
Blue Ð red terminal
Black & screen Ð white
terminal
In-hull puck (Z117)
Blue Ð red terminal
Black & screen Ð white
terminal
Retractable depth
(Z120)
Blue Ð red terminal
Black & screen Ð white
terminal
Bronze through hull
speed (Z116)
Brown & white Ð cut back
Green Ð green terminal
Screen Ð white terminal
Red Ð red terminal
Transom mount speed
(Z119)
As above
17
Chapter 2: Transducer Installation
Transducer type
Colour coding (cable to
unit)
Bronze through hull
triducer (Z093)
Brown & white Ð cut back
Red Ð red speed terminal
Screen Ð white speed
terminal
Green Ð green speed terminal
Blue Ð red depth terminal
Black & screen Ð white depth
terminal
Biducer (Z183)
Red Ð red speed terminal
Screen Ð white speed
terminal
Green Ð green speed terminal
Blue Ð red depth terminal
Black & screen Ð white depth
terminal
ST30 Bidata Operation and Installation Handbook
18
Chapter 3: Fault Finding
All Autohelm products are, prior to packing and shipping, subject to
comprehensive test and quality assurance programmes. However, in the
unlikely event that a fault does occur with the ST30 Bidata, the following
table will help to identify the probable cause and provide the most likely
cure.
Fault
Cause
Action
Instrument display
blank
No supply to
instrument
Check supply
Check cabling and
security of connectors
Check circuit breaker
Return ST30 Bidata for
repair
No speed information
Transducer cable
problem
Check transducer
connections
Transducer fouled
Clean paddlewheel
Aereated water, boat
wakes or propeller
wash
Depth reading will
return to normal once
clear of disturbed
water
Transducer cable
problem
Check transducer
connections
Speed/log information
inaccurate
Unit not calibrated
correctly
Calibrate unit as
described in the Log
Calibration section
Feet/metres display
flashes continuously
Transducer cable or
connector fault
Check cabling and
security of transducer
connector
No exchange of
information between
SeaTalk instruments
SeaTalk cabling or
connector problem
Check security of
SeaTalk connectors
No depth information
Remove instruments one
by one to isolate
faulty unit
19
Chapter 3: Fault Finding
Fault
Cause
Action
Failure of a group of Cabling or connector
instruments in a chain problem
Check the security of
the connectors between
functioning and
non-functioning
instruments
Unable to enter
calibration
Refer to Calibration
lock/unlock section
Calibration locked
Note: After installation, poor performance may be experienced if the
surface of the depth transducer has not been 'wetted'. Wetting can take
up to 24 hours under normal conditions. The transducer can be wetted
prior to launch by applying a mild detergent to the external face.
ST30 Bidata Operation and Installation Handbook
20
Chapter 4: Maintenance
4.1 Instrument
Atmospheric conditions may cause condensation to appear on the
instrument window. This will not harm the instrument and can be cleared
by increasing the illumination setting to level 3.
Chemical and abrasive materials must not be used to clean the ST30
Bidata instrument; if the instrument is dirty, clean with a soft, damp cloth.
4.2 Transducers
Refer to the Installation and Maintenance instructions supplied with the
transducers.
4.3 Cabling
Examine cables for chafing or damage to the outer shield and, where
necessary, replace and re-secure.
4.4 Advice
For advice, or further information regarding installation of this product,
please contact the Autohelm Product Support Department or your own
National Distributor.
21
Chapter 5: Operation
Chapter 5: Operation
The ST30 Bidata is set in the factory to:
• display depth in feet
• display speed in knots
• operate with the depth alarms switched off
• operate in Master mode
These settings can be changed in calibration (section 6.1).
When the ST30 Bidata is switched on, depth information (upper display)
and speed information (lower display) is shown in the units set up in
calibration.
DEPTH
Metres
SPEED
Knots
D710
Note: The trend arrows (▲) decreasing (▼) increasing, shown in the above
display, indicate whether the trend is towards deep or shallow water.
5.1 Depth Key
Each press of Depth cycles the following menu:
• Shallow alarm
DEPTH
SPEED
Shallow
Metres
Knots
D710
ST30 Bidata Operation and Installation Handbook
22
• Deep alarm
DEPTH
Deep
Metres
SPEED
Knots
D710
• Minimum depth
DEPTH
Min
SPEED
Metres
Knots
D710
• Offset Keel/Waterline
Offset
DEPTH
Metres
SPEED
Knots
D710
A further press of Depth will return the unit to current Depth. The above
menu will automatically return to current Depth after 8 seconds if
there are no further key commands.
5.2 Speed Key
Each press of Speed cycles the following menu:
• Trip Distance
DEPTH
SPEED
Metres
Trip
Nm
D710
23
Chapter 5: Operation
• Log
DEPTH
SPEED
Metres
Log
Nm
D710
• Maximum Speed
DEPTH
SPEED
Metres
Maximum
Knots
D710
• Average Speed
DEPTH
Metres
Average
SPEED
Knots
D710
A further press of Speed will return the unit to current boat speed.
Note: Log distances over 999nm or miles are displayed in thousands,
hundreds and tens (e.g., 1th 510nm).
ST30 Bidata Operation and Installation Handbook
24
5.3 Light Key
Cycles the level of instrument illumination. There are 3 levels with
level 3 the brightest.
DEPTH
Metres
SPEED
DEPTH
RESET
BIDATA
D719
TM
SPEED
The display returns to current speed after 8 seconds or when
speed key is pressed.
Note: When the ST30 Bidata is used in a SeaTalk system, illumination may
be adjusted from any instrument.
5.4 Alarms
The ST30 Bidata is equipped with visual and audible shallow water and
deep water alarms.
Both of these alarms are set in calibration (see section 6.1).
Any button press will silence the 'Shallow' alarm. However, the 'Shallow'
indicator will continue to flash until the depth exceeds the alarm value.
The 'Deep' alarm sounds when the 'Deep' setting is crossed either when
going from shallow to deep or deep to shallow waters. Any button press
will silence the alarm.
Loss of signal
The 'feet or metres' legend flashes whenever the depth signal is lost.
DEPTH
SPEED
Metres
D720
Knots
25
Chapter 6: Calibration
Chapter 6: Calibration
6.1 Depth calibration
The ST30 Bidata can be programmed to display depth information in feet
or metres, set alarms for shallow and deep water and allow for keel or
waterline offsets.
To select the calibration menu, press and hold
seconds the display will show CAL.
and Depth. After 2
DEPTH
SPEED
DEPTH
RESET
BIDATA
D685
TM
SPEED
Each press of Depth will cycle the unit through the depth calibration menu.
ST30 Bidata Operation and Installation Handbook
26
Units selection – depth
1.
Cycle Depth until the display shows feet or metres.
DEPTH
Feet
SPEED
DEPTH
SPEED
D686
BIDATA
TM
2.
RESET
Select feet or metres, as required, using Reset.
DEPTH
Metres
SPEED
DEPTH
SPEED
RESET
D687
BIDATA
TM
Shallow alarm
1.
Cycle Depth until the 'Shallow' alarm is displayed.
DEPTH
Shallow
Metres
SPEED
DEPTH
RESET
BIDATA
D688
TM
SPEED
27
Chapter 6: Calibration
2.
Press Reset or
DEPTH
to set the required depth.
Shallow
Metres
SPEED
DEPTH
SPEED
D688a
BIDATA
TM
3.
RESET
The Shallow Alarm is enabled by pressing Speed. When the alarm is
on the 'Alarm' legend is displayed.
DEPTH Alarm
Shallow
Metres
SPEED
DEPTH
SPEED
RESET
D689
BIDATA
TM
Deep alarm
1.
Cycle Depth until 'Deep' alarm is displayed.
DEPTH
Deep
Metres
SPEED
DEPTH
RESET
BIDATA
D690
TM
SPEED
ST30 Bidata Operation and Installation Handbook
28
2.
Press Reset or
DEPTH
to set the required depth.
Deep
Metres
SPEED
DEPTH
SPEED
D690a
BIDATA
TM
3.
RESET
The 'Deep' alarm is enabled by pressing Speed. When the alarm is on
the 'Alarm' legend is displayed.
Deep
DEPTH Alarm
Metres
SPEED
DEPTH
RESET
BIDATA
D691
TM
SPEED
29
Chapter 6: Calibration
Offset
The instrument measures the water depth below the transducer. To
display water depth below the keel or to the surface an offset must be set
up. A negative offset is used to reduce the displayed value to give water
depth below the keel. A positive offset will give water depth to the surface.
Waterline
Keel
Offset
Actual
Water
Depth
Depth Below Transducer
Depth
Below
Keel
Waterline
Actual
Water
Depth
Waterline
Offset
D692
Depth Below Transducer
ST30 Bidata Operation and Installation Handbook
30
1.
Press Depth until 'Offset' is selected.
Offset
DEPTH
Metres
SPEED
DEPTH
SPEED
Press Reset or
D693
BIDATA
TM
2.
RESET
until the required offset is displayed.
Offset
DEPTH
Metres
SPEED
DEPTH
RESET
BIDATA
D694
TM
SPEED
Exit depth calibration
To exit depth calibration and return to depth mode, press and hold
Depth for 2 seconds.
and
31
Chapter 6: Calibration
6.2 Speed calibration
The ST30 Bidata can be set to display speed in knots or mph and trip and
total distance in nm or miles. The most important speed calibration feature
is Log Calibration; this calibrates the transducer paddlewheel to the
vessel's hull so that accurate speed/log related information is displayed.
Press and hold
and Depth for 2 seconds until CAL is displayed.
Units selection – speed
1.
Cycle Speed until knots or mph is displayed.
DEPTH
SPEED
Knots
DEPTH
SPEED
D695
BIDATA
TM
2.
RESET
Press Reset to change between knots and mph.
DEPTH
Mph
SPEED
DEPTH
RESET
BIDATA
D696
TM
SPEED
ST30 Bidata Operation and Installation Handbook
32
Units selection – log
1.
Cycle Speed until the display shows nm or miles.
DEPTH
NM
SPEED
DEPTH
SPEED
D697
BIDATA
TM
2.
RESET
Press Reset to select nm or miles.
DEPTH
Miles
SPEED
DEPTH
SPEED
RESET
D698
BIDATA
TM
Exit calibration
Press and hold
and Depth for 2 seconds.
DEPTH
Metres
Mph
SPEED
DEPTH
RESET
BIDATA
D703
TM
SPEED
33
Chapter 6: Calibration
Log calibration
The ST30 Bidata should not be used for navigational purposes until the
transducer paddlewheel has been calibrated to suit the characteristics of
the vessel.
This is a simple operation and is carried out as follows:
1.
Choose two charted points that are approximately 1nm apart.
Point 1
Point 2
Approximately 1Nm
D699
2.
Choosing a time when the tidal flow is at a minimum, go from point 1
to point 2 and record the ST30 Bidata trip distance.
3.
Go from point 2 to point 1 and record the trip distance.
4.
Add the two distances together and divide by two to obtain an
average distance.
5.
Measure the distance between the two points on a chart.
6.
The correction factor (CF) can now be calculated.
CF = Charted Distance
Average Distance
ST30 Bidata Operation and Installation Handbook
34
Enter correction factor (CF)
1.
Press and hold
show CAL.
and Depth. After 2 seconds the display will
DEPTH
SPEED
DEPTH
SPEED
D685
BIDATA
TM
2.
RESET
Press Speed 3 times to select 'Log Calibration'.
DEPTH
SPEED
DEPTH
SPEED
D700
BIDATA
TM
3.
RESET
Set the calculated correction factor (CF) using Reset or
DEPTH
SPEED
DEPTH
RESET
BIDATA
D701
TM
SPEED
.
35
Chapter 6: Calibration
4.
To exit calibration and return to 'Speed and Depth' mode, press and
hold and Depth for 2 seconds.
DEPTH
Metres
Mph
SPEED
DEPTH
SPEED
RESET
D703
BIDATA
TM
6.3 Calibration Lock/Unlock
The lock/unlock feature removes the risk of accidentally changing the
calibration values set for log calibration, shallow alarm etc.
For security, the calibration lock/unlock feature is accessed by an
extended hold down of and Depth as follows;
1.
Press and Depth for 14 seconds until CAL is displayed for the
second time.
DEPTH
SPEED
DEPTH
RESET
BIDATA
D706
TM
SPEED
ST30 Bidata Operation and Installation Handbook
36
2.
Press Speed and Reset momentarily
DEPTH
SPEED
DEPTH
SPEED
D707
BIDATA
TM
3.
RESET
Calibration Lock/Unlock is switched on or off using Reset.
DEPTH
SPEED
DEPTH
SPEED
RESET
D708
BIDATA
TM
C0 = Calibration Locked, i.e. no access
C1 = Calibration Unlocked, i.e. normal access
4.
To exit 'Calibration Lock/Unlock', press and hold
seconds.
DEPTH
Metres
Mph
SPEED
DEPTH
RESET
BIDATA
D709
TM
SPEED
and Depth for 2
37
Chapter 6: Calibration
6.4 Master/Repeater mode
As it leaves the factory, the ST30 Bidata is set to operate in master mode.
In this mode the instrument is connected to speed and depth transducers,
and transmits data onto the SeaTalk Bus. The Bidata can be set as a
repeater, to repeat depth and speed information already on the SeaTalk
bus.
Repeater mode is set up as follows:
1.
Press and hold and Depth for 5 seconds until the display shows U
and a two figure number.
DEPTH
SPEED
DEPTH
SPEED
D704
BIDATA
TM
2.
RESET
Press Depth to display operating mode:
r0 = Master mode
r1 = Repeater mode
DEPTH
SPEED
DEPTH
RESET
BIDATA
D705
TM
SPEED
ST30 Bidata Operation and Installation Handbook
38
3.
Press Reset to change between modes
DEPTH
SPEED
DEPTH
SPEED
To exit calibration, press and hold
DEPTH
D705A
BIDATA
TM
4.
RESET
and Depth for 2 seconds.
Metres
Mph
SPEED
DEPTH
RESET
BIDATA
D705B
TM
SPEED
Note: When the Bidata is set to Repeater mode access to
calibration is inhibited.
39
Chapter 7: Specification
Chapter 7: Specification
Detailed Specification:
Power Consumption:
60mA (normal)
100mA (illuminated)
Depth transmitted power:
50W
Receiver sensitivity:
0.5mV
Depth operating frequency:
200kHz
Voltage range:
10 to 16V
Operating temperature:
0 to 70°C
Calibration lock/unlock:
Software programmable
Illumination:
3 selectable levels
Repeater capability:
Software programmable
Depth:
0 to 120m (0.1 increments)
0 to 400ft (0.1 increments)
Shallow alarm:
1 to 10m (0.1 increments)
3 to 33ft (1ft increments)
Deep alarm:
3 to 120m (1m increments)
10 to 400ft (10ft increments)
Offset:
–4 to +4m (0.1 increments)
–9.9 to +9.9ft (0.1 increments)
Minimum depth:
Reset on power-up
Units:
Software programmable selection in
metres (m) or feet (ft) – stored in
EEPROM
Depth:
ST30 Bidata Operation and Installation Handbook
40
Speed:
Boat speed:
0 to 99.9 knots or mph (0.1 increments)
Trip distance:
0 to 999nm or miles (0.01 increments to
9.99, 0.1 to 99.9 and 1.0 to 999).
Log (non resetable):
0 to 5999nm or miles (0.1 increments to
99.9 and 1.0 to 5999).
Average speed:
0 to 99.9 knots or mph (0.1 increments)
Maximum speed:
0 to 99.9 knots or mph (0.1 increments)
Units:
Software programmable selection
of knots or mph (stored in EEPROM)
and programmable selection of
nm or miles independent of knots or mph.
Manual log calibration:
0.25 to 1.50 (multiplication factor)
81003-1
TOP EDGE BLEED
MASK FOR
2 COLOUR
SEATALK
LOGO
Nautech Limited, Anchorage Park, Portsmouth
P03 5TD, England
Telephone (0705) 693611. Fax (0705) 694642
TOP EDGE BLEED
MASK FOR
2 COLOUR
SEATALK
LOGO
Nautech Limited, Anchorage Park, Portsmouth
P03 5TD, England
Telephone (0705) 693611. Fax (0705) 694642