advertisement
Model No. 831.159701
Serial No.
Write the serial number in the space above for reference.
Serial Number Decal (under seat)
®
USER’S MANUAL
SEARS, ROEBUCK AND CO.
HOFFMAN ESTATES, IL 60179
CAUTION
Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference.
Visit our website at www.imagefitness.com
new products, prizes, fitness tips, and much more!
®
Table of Contents
Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Part Identification Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Adjusting the Weight Bench . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Ordering Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Full 90-Day Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
Note: A Part List/Exploded Drawing is attached in the center of this manual. Remove the Part List/Exploded
Drawing before beginning assembly.
2
Important Precautions
WARNING:
To reduce the risk of serious injury, read the following important precautions before using the weight bench.
1. Read all instructions in this manual before using the weight bench. Use the weight bench only as described in this manual.
12. Always set both safety spotters at the same height.
13. Always wear athletic shoes for foot protection while exercising.
2. It is the responsibility of the owner to ensure that all users of the weight bench are adequately informed of all precautions.
3. The weight bench is intended for home use only. Do not use the weight bench in a commercial, rental or institutional setting.
14. The weight bench is designed to support a maximum of 560 pounds, including the user, a barbell and weights (not included). Do not place more than 310 pounds, including the barbell, on the weight gliders and safety spotters.
4. Use the weight bench only on a level surface.
Cover the floor beneath the weight bench for protection.
5. Inspect and tighten all parts each time you use the weight bench. Replace any worn parts immediately.
15. The decals shown below have been placed on the weight bench. If a decal is missing or illegible, please call our toll-free HELPLINE at
1-800-736-6879, Monday through Saturday, 7 a.m. until 7 p.m. Central Time, to order a free replacement decal. Apply the decal in the location shown.
6. Keep children under 12 and pets away from the weight bench at all times.
7. Keep hands and feet away from moving parts.
8. Always secure your weights (not included) with weight clips when they are mounted on the barbell.
9. Always make sure there is an equal amount of weight (not included) on each side of the barbell.
10. If you feel pain or dizziness at any time while exercising, stop immediately and begin cooling down.
11. Always move the bench out of the way when performing an exercise that does not use the bench.
WARNING:
Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. SEARS assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
3
Before You Begin
Thank you for selecting the versatile IMAGE weight bench. The IMAGE ®
® 3.8
3.8 is designed to help you develop every major muscle group of the body.
Whether your goal is a shapely figure, dramatic muscle size and strength, or a healthier cardiovascular system, the IMAGE ® 3.8 will help you achieve the specific results you want. at 1-800-736-6879, Monday through Saturday, 7 a.m.
until 7 p.m. Central Time (excluding holidays). To help us assist you, please note the product model number and serial number before calling. The model number is
831.159701. The serial number can be found on a decal attached to the weight bench (see the front cover of this manual).
For your benefit, read this manual carefully before using the IMAGE ® 3.8 weight bench. If you have additional questions, please call our toll-free HELPLINE
Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled.
Note: The terms “right side” and “left side” are determined relative to a person sitting on the bench. They do not refer to right and left on the drawings in this manual.
Right Side
Weight Guide
Left Side
Upright
Barbell
Weight Glider
Weight
Storage
Tube
Safety Spotter
Backrest
Seat
Adjustment
Bracket
4
Part Identification Chart—Model No. 831.159701
R1200A
M6 x 55mm Bolt (4)—4
M6 x 38mm Bolt (60)—1
M6 Washer (30)—5
M6 x 16mm Screw (3)—2
M10 Washer (6)—14
M8 Washer (52)—10
M8 Nylon Locknut (54)—11
M10 Nylon Locknut (11)—26
M8 x 70mm Bolt (41)—4
M10 x 25mm Bolt (43)—2
M8 x 65mm Carriage Bolt (59)—4
M10 x 65mm Carriage Bolt (40)—8
M8 x 60mm Bolt (39)—2
M10 x 65mm Bolt (42)—4
M8 x 30mm Bolt (38)—2
M10 x 70mm Bolt (46)—8
M10 x 25mm Bolt (53)—2
M10 x 80mm Bolt (56)—1
M8 x 20mm Screw (50)—2
5
M10 x 115mm Bolt (55)—1
Assembly
Before beginning assembly, carefully read the following information and instructions:
Make Things Easier for Yourself!
This manual is designed to ensure that the weight bench can be assembled successfully by anyone. By setting aside plenty of time, and by deciding to make the task enjoyable, assembly will go smoothly.
• Assembly requires two people.
• Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed.
• Tighten all parts as you assemble them, unless instructed to do otherwise.
• As you assemble the weight bench, make sure all parts are oriented as shown in the drawings.
• For help identifying small parts, use the PART
IDENTIFICATION CHART on page 5. Note:
Some small parts may be pre-assembled.
In addition to the included allen wrench , assembly requires the following tools (not included):
• Two (2) adjustable wrenches
• One (1) rubber mallet
• One (1) standard screwdriver
• One (1) phillips screwdriver
• Lubricant, such as grease or petroleum jelly, and soapy water.
Assembly will be more convenient if you have the following tools: A socket set, a set of open-end or closed-end wrenches or a set of ratchet wrenches.
1.
Before beginning, make sure that you understand the information in the box above. Note: Some parts described in the assembly steps may be pre-assembled.
Press a 50mm Square Outer Cap (17) onto each end of a Base (7). Turn the Base so the large hole is in the position shown. Insert two M8 x 65mm Carriage
Bolts (59) and two M10 x 65mm Carriage Bolts (40) up into the indicated holes in the Base. Place the
Base flat on the floor.
Turn the Base Crossbar (20) so the warning decal is positioned as shown. Attach the Base (7) to the Base
Crossbar with two M8 x 70mm Bolts (41), a Large
Support Plate (12), and two M8 Nylon Locknuts (54).
Do not tighten the Nylon Locknuts yet.
2.
Press a 50mm Square Outer Cap (17) onto each end of the other Base (7). Turn the Base so the large hole is in the position shown. Insert two M8 x 65mm
Carriage Bolts (59) and two M10 x 65mm Carriage
Bolts (40) up into the indicated holes in the Base.
Place the Base flat on the floor.
Attach the Base (7) to the Base Crossbar (20) with two M8 x 70mm Bolts (41), a Large Support Plate
(12), and two M8 Nylon Locknuts (54). Do not tighten the Nylon Locknuts yet.
1
17
2
17
20
Large Hole
Large Hole
54
40
40
41
Decal
54
7
7
12
59
59
54
17
12
17
41
54
20
6
3.
Slide a Brace (2) onto the bracket on one of the
Uprights (1). Attach the Brace to the Upright with two
M10 x 65mm Bolts (42), four M10 Washers (6), and two M10 Nylon Locknuts (11). Do not tighten the
Nylon Locknuts yet.
Slide the Upright (1) and the Brace (2) onto the M10 x 65mm Carriage Bolts (40) and the M8 x 65mm
Carriage Bolts (59) in the left Base (7). Attach the
Upright with two M10 Nylon Locknuts (11). Attach the
Brace with two M8 Washers (52) and two M8 Nylon
Locknuts (54). Do not tighten the Nylon Locknuts yet.
3
1
11
6
2
6
Bracket
42
54
52
11
59
40
7
4.
Slide the remaining Brace (2) onto the bracket on the other Upright (1). Attach the Brace to the Upright with two M10 x 65mm Bolts (42), four M10 Washers (6), and two M10 Nylon Locknuts (11). Do not tighten the Nylon Locknuts yet.
Slide the Upright (1) and the Brace (2) onto the M10 x 65mm Carriage Bolts (40) and the M8 x 65mm
Carriage Bolts (59) in the right Base (7). Attach the
Upright with two M10 Nylon Locknuts (11). Attach the
Brace with two M8 Washers (52) and two M8 Nylon
Locknuts (54). Do not tighten the Nylon Locknuts yet.
4
1
42
6
2
6
11
Bracket
54
52
59
11
7
40
7
5.
Press a 25mm Round Inner Cap (51) into the end of a Weight Storage Tube (21).
While a second person holds a Crossbar (8) in the position shown, insert two M10 x 70mm Bolts (46) through the bracket on the Weight Storage Tube (21), the left Brace (2), and the bracket on the Crossbar.
Thread an M10 Nylon Locknut (11) onto each Bolt.
Do not tighten the Nylon Locknuts yet.
5
8
11
2
21
46
6.
Press a 25mm Round Inner Cap (51) into the end of the other Weight Storage Tube (21).
While a second person continues to hold the
Crossbar (8), insert two M10 x 70mm Bolts (46) through the bracket on the Weight Storage Tube (21), the right Brace (2), and the bracket on the Crossbar.
Thread an M10 Nylon Locknut (11) onto each Bolt.
Do not tighten the Nylon Locknuts yet.
6 51
46
46
2
21
8
11
7.
Have a second person hold the other Crossbar (8) between the Uprights (1).
Attach the Crossbar (8) to the left Upright (1) with two
M10 x 70mm Bolts (46), a Small Support Plate (16), and two M10 Nylon Locknuts (11). Do not tighten the Nylon Locknuts yet.
Attach the Crossbar (8) to the right Upright (1) with two M10 x 70mm Bolts (46), a Small Support Plate
(16), and two M10 Nylon Locknuts (11). Do not tighten the Nylon Locknuts yet.
7
46
46
16
11
11
8
11
11
46 51
16
46
1
1
46
8
8.
Press a 25mm Bushing (48) into each end of the
Locking Bar (34).
Insert the Barbell (35) through the Locking Bar (34) until the Barbell is centered in the Locking Bar.
8
48 34
35
48
9.
Identify the Left Weight Glider (32) by looking at the position of the round tube.
Press a 38mm Bushing (29) into each end of the round tube on the Left Weight Glider (32).
Slide the Left Weight Glider (32) onto the left end of the Barbell (35). Secure the Weight Glider to the
Barbell with a hand-tightened M8 x 20mm Screw (50).
Look at the drawing on page 4 to make sure that you have correctly identified the left end. The Left
Weight Glider must be turned as shown in the drawing.
9
35
10. Identify the Right Weight Glider (31) by looking at the position of the round tube.
Press a 38mm Bushing (29) into each end of the welded tube on the Right Weight Glider (31).
Slide the Right Weight Glider (31) onto the right end of the Barbell (35). Secure the Weight Glider to the
Barbell with a hand-tightened M8 x 20mm Screw (50).
Make sure that the Weight Glider is turned as shown in the drawing.
10
29
Round tube
31
50
29
29
32
Round tube
35
50
29
11. Identify the Left Safety Spotter (24) by the position of the handle and the Left Spotter Hook (62). Place the
Left Safety Spotter on the left Base (7) so it is centered over the indicated hole.
Have a second person hold the Locking Bar (34) so that the Left Weight Glider (32) rests on top of the
Left Safety Spotter (24). Insert a Weight Guide (18) into the Left Weight Glider, the Left Safety Spotter, and the hole in the Base (7). Note: Tilt the Weight
Guide away from the Upright (1) as you insert it.
Attach the Weight Guide (18) to the Base (7) with an
M8 x 60mm Bolt (39), two M8 Washers (52), and an
M8 Nylon Locknut (54). Do not tighten the Nylon
Locknut yet.
9
11
18
34
Handle
32
24
54
52
1
62
39
Hole
7
12. Place the Right Safety Spotter (23) on the right Base
(7) and center it over the indicated hole. Note: The handle must point toward the center of the bench.
Have a second person hold the Locking Bar (34) so that the Right Weight Glider (31) rests on top of the
Right Safety Spotter (23). Insert a Weight Guide (18) into the Right Weight Glider, the Right Safety Spotter, and the hole in the Base (7). Note: It may be necessary to tilt the Weight Guide away from the
Upright (1) as you insert it.
Attach the Weight Guide (18) to the Base (7) with an
M8 x 60mm Bolt (39), two M8 Washers (52), and an
M8 Nylon Locknut (54). Do not tighten the Nylon
Locknut yet.
12
18
31
39
23
52
1
34
Handle
Hole
54
7
13.
Note: If you are not planning to use Olympic weights with the weight bench, you do not need to perform this step. Keep the two Weight
Adapters (33) in a safe place in case you need them in the future.
Fully engage the indicated hook on both sides of the weight bench before beginning this step.
Insert a 50mm Bushing (47) into the end of a Weight
Adapter (33). With a second person holding the
Barbell (35) so that it cannot turn, use the allen wrench to secure the Weight Adapter to the Barbell with a Large Washer (44) and an M10 x 25mm Bolt
(43). Note: The Large Washer must fit into the indentation in the 50mm Bushing in the Weight
Adapter.
Pull the remaining length of the Barbell (35) in the direction shown.
Next, tighten the M8 x 20mm
Screws used in steps 9 and 10. Attach the other
Weight Adapter (33) to the other end of the Barbell in the same manner.
14. Attach the upper end of one of the Weight Guides
(18) to the bracket on the Upright (1) with an M8 x
30mm Bolt (38) and an M8 Washer (52).
Attach the other Weight Guide (18) to the other
Upright (1) in the same manner.
Tighten all of the Nylon Locknuts used in steps 1 to 14.
13
14
Hook
35
18
38
52
33
47
44
43
1
10
15. Press a 50mm Square Outer Cap (17) onto each end of the Small Stabilizer (25).
Attach the Small Stabilizer (25) to the Bench Frame
(5) with two M10 x 65mm Carriage Bolts (40) and two
M10 Nylon Locknuts (11). Note: There is an indentation around the holes on one side of the Small
Stabilizer. This side must be facing the floor.
15
17
11
5
25
17
40
16. Press a 50mm x 70mm Outer Cap (10) onto each end of the Large Stabilizer (26).
Turn the Large Stabilizer (26) so the warning decal is in the position shown. Attach the Large Stabilizer to the Bench Frame (5) with two M10 x 65mm Carriage
Bolts (40) and two M10 Nylon Locknuts (11). Note:
There is an indentation around the holes on one side of the Large Stabilizer. This side must be facing the floor.
16
5
10
26
11
Decal
10
40
17. Press two 20mm x 40mm Inner Caps (28) into each
Backrest Tube (27). Press four 20mm x 40mm Inner
Caps into the Backrest Adjustment Bracket (36).
Lubricate an M10 x 180mm Bolt (22). Attach the
Backrest Tubes (27) to the welded tube on the
Backrest Adjustment Bracket (36) with the Bolt, two
M10 Washers (6), and an M10 Nylon Locknut (11).
Make sure that the Backrest Tubes are turned as shown. The indicated holes are not centered in the Backrest Tubes but are closer to one side.
Turn the Backrest Tubes so the holes are closer to the floor. Do not over tighten the Nylon
Locknut; the Backrest Tubes must pivot easily.
18. Lubricate an M10 x 115mm Bolt (55). Slide an M10
Washer (6) onto the Bolt. Hold the hole in the
Backrest Adjustment Bracket (36) on the outside of the bracket on the Bench Frame (5).
Inserting the M10 x 115mm Bolt (55) through the one side of the Backrest Adjustment Bracket, one side of the bracket on the Bench Frame, and through the
15mm x 10.2mm x 60mm Spacer (57). Then, insert the Bolt through the other side of the bracket on the
Bench Frame and the Backrest Adjustment Bracket.
Secure the Bolt with an M10 Washer (6) and an M10
Nylon Locknut (11). Do not over tighten the Nylon
Locknut.
11
17
22
Holes
18
55
Lubricate
6
28
28
Welded
Tube
Lubricate
6
5
36
27
27
57
Bracket
6
11
28
28
36
Hole
6
11
19. Lubricate an M10 x 180mm Bolt (22). Attach the
Backrest Tubes (27) to the indicated tube on the
Bench Frame (5) with the Bolt, two M10 Washers (6), and an M10 Nylon Locknut (11). Note: Do not over tighten the Nylon Locknut; the Backrest Tubes must pivot easily.
19
22
Lubricate
6
5
27
Tube
6
11
20. Attach the Backrest (15) to the Backrest Tubes (27) with four M6 x 55mm Bolts (4) and four M6 Washers
(30).
20
15
27
4
30
21. Press a 25mm x 50mm Inner Cap (58) into the open end of the Seat Support Tube (37).
Lubricate an M8 x 80mm Bolt (9). Attach the Seat
Adjustment Bracket (45) to the indicated side of the
Seat Support Tube (37) with the Bolt and an M8
Nylon Locknut (54). Note: Do not over tighten the
Nylon Locknut; the Seat Adjustment Bracket must pivot easily.
21
Lubricate
9
30
4
45
30
58
37
54
22. Place the Seat Support Tube (37) on the Bench
Frame (5) so that the Seat Adjustment Bracket (45) fits over the welded pin (not visible in the drawing) on the side of the Bench Frame.
Lubricate an M10 x 80mm Bolt (56). Attach the Seat
Support Tube (37) to the indicated bracket on the
Bench Frame (5) with the Bolt and an M10 Nylon
Locknut (11). Note: Do not over tighten the Nylon
Locknut; the Seat Support Tube must pivot easily.
22
Welded
Pin
37
45
56
Lubricate
5
11
12
23. Turn the Seat (14) as shown. Attach the wide end of the Seat to the bracket on the Seat Support Tube
(37) with two M6 x 16mm Screws (3).
Tilt the Seat Support Tube (37) upwards and attach the narrow end of the Seat (14) to the Seat Support
Tube with an M6 x 38mm Bolt (60) and an M6
Washer (30).
23
14
37
3
30
60
24.
Make sure that all parts are properly tightened before you use the weight bench. The use of all remaining parts will be explained in ADJUSTING THE WEIGHT BENCH starting on the following page.
13
Adjusting the Weight Bench
This section explains how the weight bench is adjusted. See the included exercise guide for important information about how to perform a variety of exercises and how to get the greatest benefit from your exercise program.
Inspect and tighten all parts each time you use the weight bench. Replace any worn parts immediately. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
USING THE LOCKING BAR AND SAFETY SPOTTERS
Before starting an exercise, position the Barbell (35) and the Safety Spotters (23, 24) in the correct position for that exercise.
To do this, stand in front of the cage and grip the Locking
Bar (34) with both hands. Turn the Locking Bar until the two hooks disengage the slots in the Uprights (1). Move the Locking Bar to a new position and turn the Locking
Bar until the hooks engage the slots in the Uprights.
Note: Always start an exercise with the barbell positioned at the lowest point to which it will move during the exercise.
Position both Safety Spotters (23, 24) directly under the
Weight Gliders (31, 32).
31
23
34
1
32
24
1
35
USING THE SAFETY SPOTTERS
To move a Safety Spotter (23, 24 [not shown]) to a new position, grip the handle on the side of the Spotter Hook
(61, 62 [not shown]) and pull the Spotter Hook out of the slot in the Upright (1). Raise or lower the Safety Spotter to a new position and turn the Spotter Hook until it engages one of the slots in the Upright.
WARNING:
Always set both Safety
Spotters at the same height.
ATTACHING WEIGHTS TO THE BARBELL
To use the Barbell (35), slide the desired amount of weight (not included) onto each end of the Barbell.
Secure the weights with the Large Weight Clips (13).
Note: To use standard weights, the Weight Adapters (33) should be removed from the Barbell. Attach weights to the Barbell with the Small Weight Clips (not shown).
WARNING:
Do not place more than
260 pounds on the barbell. Always secure the weights with weight clips when they are on the barbell. Always place the same amount of weight on each side of the barbell.
35
23
33
1
61
Handle
13
14
ADJUSTING THE BACKREST
To raise the Backrest (15), grip the end of the Backrest with one hand and pull it upward. The Backrest
Adjustment Frame (36) will automatically lock into one of the tabs on the bracket on the Bench Frame (5).
To lower the Backrest (15), grip the end of the Backrest with one hand and pull it slightly upwards. Grip the handle
(not shown) on the right side of the Backrest Adjustment
Frame (36) with your other hand and pull the Backrest
Adjustment Frame free of the tabs on the bracket on the
Bench Frame (5). Lower the Backrest to the desired position and lock the Backrest Adjustment Frame into the desired tab on the bracket on the Bench Frame.
ADJUSTING THE SEAT
To raise the Seat (14), lift the narrow end of the Seat until the appropriate tab on the Seat Adjustment Bracket (45) engages the welded pin (not shown) on the right side of the Bench Frame (5).
To lower the Seat (14), use the handle on the Seat
Adjustment Bracket (45) to disengage the Seat
Adjustment Bracket from the pin. Lower the Seat to the desired position and engage the appropriate tab on the
Seat Adjustment Bracket to the pin.
Handle
15
Adjustment
Bracket
36
5
14
Handle
Pin
45
5
15
Part List—Model No. 831.159701
R1200A
Key No.
Qty. Description Key No. Qty. Description
1
1
4
5
2
2
8
1
1
1
1
2
2
2
1
6
2
1
2
2
1
1
2
26
2
1
14
2
2
2
4
2
2
29
30
31
32
33
25
26
27
28
21
22
23
24
17
18
19
20
13
14
15
16
9
10
11
12
7
8
5
6
3
4
1
2
Upright
Brace
M6 x 16mm Screw
M6 x 55mm Bolt
Bench Frame
M10 Washer
Base
Crossbar
M8 x 80mm Bolt
50mm x 70mm Outer Cap
M10 Nylon Locknut
Large Support Plate
Large Weight Clip
Seat
Backrest
Small Support Plate
50mm Square Outer Cap
Weight Guide
Small Weight Clip
Base Crossbar
Weight Storage Tube
M10 x 180mm Bolt
Right Safety Spotter
Left Safety Spotter
Small Stabilizer
Large Stabilizer
Backrest Tube
20mm x 40mm Inner Cap
38mm Bushing
M6 Washer
Right Weight Glider
Left Weight Glider
Weight Adapter
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
#
#
#
1
1
1
1
2
2
8
4
4
2
2
1
8
2
2
8
2
2
10
2
11
1
1
1
1
4
1
1
1
1
1
1
Locking Bar
Barbell
Backrest Adjustment Bracket
Seat Support Tube
M8 x 30mm Bolt
M8 x 60mm Bolt
M10 x 65mm Carriage Bolt
M8 x 70mm Bolt
M10 x 65mm Bolt
M10 x 25mm Bolt
Large Washer
Seat Adjustment Bracket
M10 x 70mm Bolt
50mm Bushing
25mm Bushing
45mm x 45mm Bushing
M8 x 20mm Screw
25mm Round Inner Cap
M8 Washer
M10 x 25mm Bolt
M8 Nylon Locknut
M10 x 115mm Bolt
M10 x 80mm Bolt
15mm x 10.2 mm x 60mm Spacer
25mm x 50mm Inner Cap
M8 x 65mm Carriage Bolt
M6 x 38mm Bolt
Right Spotter Hook
Left Spotter Hook
User’s Manual
Exercise Guide
6mm Allen Wrench
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of the user’s manual for information about ordering replacement parts.
Exploded Drawing—Model No. 831.159701
R1200A
Ordering Replacement Parts
Model No. 831.159701
QUESTIONS?
If you find that:
• you need help assembling or operating the IMAGE 3.8
• a part is missing
• or you need to schedule repair service call our toll-free HELPLINE
1-800-736-6879
Monday–Saturday, 7 am–7 pm
Central Time (excluding holidays)
The model number and serial number of your IMAGE 3.8 are listed on a decal attached to the frame. See the front cover of this manual to find the location of the decal.
All replacement parts are available for immediate purchase or special order when you visit your nearest SEARS Service
Center. To request service or to order parts by telephone, call the toll-free numbers listed at the left.
When requesting help or service, or ordering parts, please be prepared to provide the following information:
• The MODEL NUMBER of the product (831.159701)
• The NAME of the product (IMAGE 3.8 weight bench)
• The PART NUMBER of the PART (see the PART LIST and the
EXPLODED DRAWING at the center of this manual)
• The DESCRIPTION of the PART (see the PART LIST and the
EXPLODED DRAWING at the center of this manual).
REPLACEMENT
PARTS
If parts become worn and need to be replaced, call the following tollfree number
1-800-FON-PART
(1-800-366-7278)
Full 90 Day Warranty
SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179
For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this
SEARS WEIGHT BENCH EXERCISER, contact the nearest SEARS Service Center throughout the United
States and SEARS will repair or replace the WEIGHT BENCH EXERCISER, free of charge.
This warranty does not apply when the WEIGHT BENCH EXERCISER is used commercially or for rental purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
SEARS, ROEBUCK AND CO., DEPT. 817WA, HOFFMAN ESTATES, IL 60179
Part No. 172630 R1200A Printed in China © 2000 Sears, Roebuck and Co.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project