Dryer
DC 7110
Read this manual prior to initial operation of the product!
Dear Customer,
We hope that your product, which has been manufactured in modern facilities and passed
through a strict quality control procedure, will give you very good results.
We advise you to read through this manual carefully before using your product and keep it for
future reference.
This User Manual will
• Help you use your machine in a fast and safe way.
• Read the User Manual before installing and starting your product.
• In particular, follow the instructions related to safety.
• Keep this User Manual within easy reach for future reference.
• Please read all additional documents supplied with your product.
Remember that this User Manual is also applicable for several other models.
Explanation of symbols
Throughout this User Manual the following symbols are used:
B
Important safety information. Warning for hazardous situations with regard to life and property.
Caution; Warning for supply voltage.
Caution; Warning for fire hazard.
Caution; Warning for hot surfaces.
Read the instructions.
C
Useful information. Important information or useful hints about usage.
This appliance’s packaging material is recyclable. Help recycle it and protect the
environment by dropping it off in the municipal receptacles provided for this purpose.
Your appliance also contains a great amount of recyclable material. It is marked with
this label to indicate the used appliances that should not be mixed with other waste.
This way, the appliance recycling organised by your manufacturer will be done under
the best possible conditions, in compliance with European Directive 2002/96/EC on
Waste Electrical and Electronic Equipment. Contact your town hall or your retailer
for the used appliance collection points closest to your home. We thank you doing your part to
protect the environment.
2 EN
2960310581_EN/271211.1116
A
1 Important safety information
This section includes safety information that will
help protection from risks of personal injuries
or materialistic damages. Failure to follow
these instructions shall cause any warranty and
reliability commitment to become void.
General safety
• Never place the machine on a carpet-covered
floor, otherwise, lack of airflow beneath
the machine may cause electrical parts to
overheat. This will cause problems with your
machine.
• If the power cable or mains plug is damaged,
you must call Authorised Service Agent for
repair.
• The product should not be plugged in during
installation, maintenance and repair works.
Such works should always be made by the
technical service. Manufacturer shall not
be held responsible for damages arising
from processes carried out by unauthorised
persons.
• Connect the product to a grounded outlet
protected by a fuse of suitable capacity as
stated in the technical specifications table.
• Operate your product at temperatures
between +5°C and +35°C.
• Do not use electrical devices in the product.
• Do not connect the air exit of the product
to the chimney holes which are used for the
exhaust fumes of the devices operating with
gas or other types of fuel.
• You must provide enough ventilation in
order to prevent gases exiting from devices
operating with other types of fuels including
the naked flame from accumulating in the
room due to the back fire effect.
• Always clean the lint filter before or after each
loading.
• Never operate your dryer without the lint filter
installed.
• Do not allow fibre, dust and dirt accumulation
around the exhaust exit and at adjacent
areas.
• Power cable plug must be within easy reach
after installation.
• Do not use extension cords, multi-plugs
or adaptors to connect the dryer to power
supply in order to decrease the risk of electric
shock.
• Do not make any changes on the plug
supplied with the product. If it is not
compatible with the socket, have a qualified
electrician change the socket with a suitable
one.
• Items cleaned or washed with gasoil/fuel oil,
dry-laundry solvents and other combustible
or explosive materials as well as the items
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
that are contaminated or spotted with such
materials should not be dried in the product
since they emit flammable or explosive vapor.
Do not dry items cleaned with industrial
chemicals in the dryer.
Do not dry unwashed items in the dryer.
Items soiled with cooking oils, acetone,
alcohol, fuel oil, kerosene, stain remover,
turpentine, paraffin and paraffin removers
must be washed in hot water with plenty of
detergent before being dried in the dryer.
Garments or pillows bolstered with rubber
foam (latex foam), shower bonnets, water
resistant textiles, materials with rubber
reinforcement and rubber foam pads should
not be dried in the dryer.
Do not use fabric softeners and anti-static
products unless they are recommended by
the manufacturers of the fabric softener or
the product.
This product must be grounded. Grounding
installation decreases the risk of electric
shock by opening a path with low resistance
for the electricity flow in case of a malfunction
or failure. Power cable of this product is
equipped with a conductor and a grounding
plug that allows for grounding the product.
This plug must be installed appropriately and
inserted into a socket which is grounded
in accordance with the local laws and
regulations.
Do not install the product behind a door with
a lock, sliding door or a door that has a hinge
against the hinge of the dryer.
Do not install or leave this product in
places where it will be exposed to outdoor
conditions.
Do not tamper with the controls.
Do not perform any repair or part replacing
procedures on the product even if you know
or have the ability to perform unless it is
clearly suggested in the operating instructions
or the published service manual.
Inside and exhaust duct of the product must
be cleaned by the qualified service personnel
periodically.
Wrong connection of grounding conductor
of the product can cause electric shock. If
you have any suspect about the grounding
connection, have it checked by a qualified
electrician, service representative or service
personnel.
Do not reach into the machine when the
drum is spinning.
Unplug the machine when it is not in use.
Never wash down the appliance with water!
There is the risk of electric shock! Always
3 EN
•
•
•
•
•
•
•
•
•
•
disconnect by unplugging from the mains
before cleaning.
Never touch the plug with wet hands. Never
unplug by pulling on the cable, always
pull out by grabbing the plug only. Do not
operate the machine if the power cable or
plug is damaged!
Never attempt to repair the machine
yourself, otherwise, you will be putting your
life and others’ lives in danger.
For malfunctions that cannot be solved by
following the information given in the safety
instructions:
Turn off the machine, turn off and contact an
authorised service agent.
Do not stop the dryer before the drying
cycle comes to an end unless you will
remove all laundry from the dryer fast in
order to lay them and dissipate the heat.
Remove the door of the drying compartment
before decommissioning or disposing of the
product.
The final step of the drying cycle (cooldown cycle) occurs without applying
heat to ensure that the items are left at a
temperature that will not damage them.
Fabric softeners or similar products should
be used as specified by the fabric softener
instructions.
Underwear that contains metal
reinforcements should not be placed in
a dryer. Damage to the dryer can result if
metal reinforcements come loose during
drying.
Check all garments for forgotten lighters,
coins, metal pieces, needles, etc. before
loading.
At times when your dryer is not in use or
after the laundry is taken out following the
completion of drying process, turn off by
using the On/Off button. In cases when
the On/Off button is on (while the dryer
is energized), keep the door of the dryer
closed.
Children’s safety
• Electrical appliances are dangerous for
the children. Keep children away from the
machine when it is operating. Do not let
them tamper with the machine.
• Packaging materials are dangerous to
children. Keep the packaging materials out
of reach of children or dispose them by
classifying according to waste directives.
• Do not allow children sit/climb on or enter in
the product.
• Children should be supervised to ensure
that they do not play with the product.
• Close the loading door when you leave the
area where the product is located.
Intended use
• This product has been designed for
domestic use. It should not be used for
other purposes.
• Use the product only for drying laundry that
are marked accordingly.
• Dry only those articles in your product that
are stated in this manual.
• This product is not intended to be used by
persons with physical, sensory or mental
disorders or unlearned or inexperienced
people (including children) unless they
are attended by a person who will be
responsible for their safety or who will
instruct them accordingly for use of the
product.
4 EN
2 Installation
Refer to the nearest Authorised Service Agent
for installation of your product.
CPreparation of location and electrical
installation for the product is under
customer’s responsibility.
BInstallation and electrical connections must
be carried out by a qualified personnel.
APrior to installation, visually check if the
product has any defects on it. If so, do not
have it installed. Damaged products will
cause risks for your safety.
Appropriate installation location
• Install the product in an environment which
has no risk of freezing and is in a stable and
level position.
• Operate your product in a well ventilated,
dust-free environment.
• Do not block the air ducts in front of and
under the product with materials such as
long pile rugs and wooden bands.
• Do not place your product on a long pile rug
or on similar surfaces.
• Do not install the product behind a door with
a lock, sliding door or a hinged door which
can strike the product.
• Once the product is installed, it should stay
at the same place where its connections
have been made. When installing the
product, make sure that the rear wall of it
does not touch anywhere (tap, socket, etc.)
and also pay attention to install the product
at a place where it will stay permanently.
B Do not place the product on top of the
power cable.
• Keep at least 1.5 cm distance to walls of
other furniture.
Removing the transportation safety
assembly
ARemove the transportation safety assembly
before using the product for the first time.
1. Open the loading door.
2. There is a nylon bag inside the drum that
contains a piece of styrofoam. Hold it from
its section marked with XX.
3. Pull the nylon towards yourself and remove
the transportation safety assembly.
AMake sure that you have removed
the transportation safety assembly
(nylon+styrofoam pieces) before using the
product for the first time. Do not leave any
items inside the drum.
Under counter installation
• A special part (Part no. 297 360 0100)
replacing the top trim must be provided and
installed by the Authorised Service Agent in
order to use the machine under a counter or
in a cupboard. It should never be operated
without the top trim.
• Leave at least 3 cm of space between
the side and rear walls of the product and
the walls of the counter/cupboard when
installing your product under a counter or in
a cupboard.
Mounting over a washing machine
• A fitting device should be used between
the two machines when installing above a
washing machine. The bracket (Part no. 297
720 0200 white/297 720 0500 grey) must be
installed by the Authorised Service Agent.
• Place the product on a firm floor. If it will be
placed on top of a washing machine, the
approximate weight of both machines may
reach 180 kg when they are full. Therefore,
the floor must be capable of carrying the
load on it!
Adjusting the feet
In order to ensure that your machine operates
more silently and vibration-free, it must stand
level and balanced on its feet. Balance the
machine by adjusting the feet.
Rotate the feet to adjust until the machine
stands level and firmly.
5 EN
accordance with recycled waste instructions.
Do not dispose of them with normal domestic
waste.
Transportation of the machine
CNever unscrew the adjustable feet from their
housings.
Electrical connection
Connect the machine to a grounded outlet
protected by a fuse of suitable capacity as
stated in the technical specifications table. Our
company shall not be liable for any damages
that will arise when the machine is used on a
circuit without grounding.
• Connection must comply with national
regulations.
• If the current value of the fuse or breaker
in the house is less than 13 Amps, have a
qualified electrician install a 13 Amp fuse.
• Power cable plug must be within easy reach
after installation.
• The voltage and allowed fuse or breaker
protection are specified in the “Technical
Specifications” section.
• The specified voltage must be equal to your
mains voltage.
• Do not make connections via extension
cables or multi-plugs.
• The main fuse and switches must have a
contact distance of minimum 3 mm.
BDamaged power cable must only be replaced
by a qualified electrician.
BIf the product is faulty, it must not be
operated unless it is repaired! There is the risk
of electric shock!
1. Unplug the machine from the mains.
2. Remove the water drain (if any) and
chimney connections.
3. Drain water remained in the machine
completely before transportation.
Disposing of the old machine
Dispose of your old machine in an
environmentally friendly manner.
Refer to your local dealer or solid waste
collection centre in your area to learn how to
dispose of your machine.
Before disposing of your old machine, cut off
the power cable plug and make the loading
door lock unusable to avoid dangerous
conditions to children.
First use
• To have the product ready for operation
before calling the authorised service agent,
make sure that its location and power supply
installations are appropriate. If they are
not, call a qualified electrician to have any
necessary arrangements carried out.
• Make sure that the power connections of
the product are in accordance with the
instructions given in relevant chapters of this
manual.
Disposing of packaging material
Packaging materials are dangerous to children.
Keep packaging materials in a safe place out
of reach of children. Packaging materials of
your product are manufactured from recyclable
materials. Sort and dispose of them in
6 EN
Technical Specification
EN
2
Height (adjustable)
84.6 cm
Width
59.5 cm
Depth
53 cm
Capacity (max.)
7 kg
Weight (net)
35 kg
Voltage
Rated power input
See type label
Model code
Type label is located behind the loading door.
7 EN
3 Initial preparations for drying
Things to be done for energy saving:
• Make sure that you operate the product
at its full capacity but pay attention to not
exceeding it.
• Spin your laundry at the highest speed
possible when washing them. Thus,
the drying time is shortened and energy
consumption is decreased.
• Pay attention to dry same types of laundry
together.
• Follow the instructions in the user manual for
programme selection.
• Make sure that sufficient clearance is
provided at the front and rear side of the
dryer for air circulation. Do not block the grill
at the front side of the product.
• Do not open the door of the machine during
drying unless necessary. If you must certainly
open the door, pay attention not to keep it
open for a long time.
• Do not add new (wet) laundry during drying.
• Lint and fibres released from the laundry to
the air during the drying cycle are collected in
the “Lint Filter”. Make sure that you clean the
filters before or after each drying.
• In models with condenser, make sure that
you clean the condenser regularly at least
once every month or after every 30 drying
cycles.
• In vented models, follow the chimney
connection rules in the user manual and pay
attention to the chimney cleaning.
• Ventilate the room, where the dryer is located,
well during drying.
• For power saving in models with lamps, at
times when your dryer is not in use, keep the
door closed if the On/Off button is pressed (if
the dryer is energized).
Laundry suitable for drying in the
machine
Low
l n m
o p q
Laundry unsuitable for drying in the
machine
• Laundry items with metal attachments such
•
•
•
•
•
CAlways follow the suggestions on the laundry
labels. Dry only the laundry having a label
stating that they are suitable for drying in
a dryer and make sure that you select the
appropriate programme.
A B C D
•
•
•
•
•
•
8 EN
as belt buckles and metal buttons can
damage your dryer.
Do not dry items such as woollens, silk
garments and nylon stockings, delicate
embroidered fabrics, laundry with metal
accessories and items such as sleeping bags
in the dryer.
Laundry made of delicate and valuable fabrics
as well as lace curtains can be creased. Do
not dry them in the dryer!
Do not dry items made of hermetic fibres
such as pillows and quilts in the dryer.
Laundry made of foam or rubber will be
deformed.
Do not dry laundry containing rubber in the
dryer.
Do not dry laundry exposed to petroleum, oil,
combustible or explosive agents in the dryer
even if they are washed beforehand.
Overly wet laundry or laundry with dripping
water must not be put into the dryer.
Items cleaned or washed with gasoil/fuel oil,
dry-laundry solvents and other combustible
or explosive materials as well as the items
that are contaminated or spotted with such
materials should not be dried in the product
since they emit flammable or explosive vapor.
Do not dry items cleaned with industrial
chemicals in the dryer.
Do not dry your unwashed laundry in the
dryer.
Items soiled with cooking oils, acetone,
alcohol, fuel oil, kerosene, stain remover,
turpentine, paraffin and paraffin removers
must be washed in hot water with plenty of
detergent before being dried in the dryer.
• Garments or pillows bolstered with rubber
foam (latex foam), shower bonnets, water
resistant textiles, materials with rubber
reinforcement and rubber foam pads
should not be dried in the dryer.
• Do not use fabric softeners and anti-static
products unless they are recommended by
the manufacturers of the fabric softener or
the product.
• Do not dry the underwear reinforced with
metal parts in the dryer. If these metal
reinforcements loosen and break during
drying, they will damage your dryer.
Preparing laundry for drying
• Check all laundry items before loading
•
•
•
•
degrade when the machine is overloaded.
Furthermore, your dryer and your laundry
can be damaged.
CPlace your laundry into the drum loosely so
that they will not get tangled.
CLarge pieces (E.g.: bed sheets, quilt covers,
large tablecloths) may bunch-up. Stop the
dryer 1-2 times during drying process to
separate bunched-up laundry.
Following weights are given as examples.
them into the product to make sure that
there are no lighters, coins, metal items,
needles and etc. in their pockets or on any
part of them.
Fabric softeners and similar products must
be used in accordance with the instructions
of the manufacturer of the relevant
products.
All laundry must be spun at the highest
spin speed that your washing machine
allows for the laundry type.
Laundry may be tangled after washing.
Separate your laundry before placing them
into your dryer.
Sort your laundry according to their types
and thicknesses. Dry the same type of
laundry together. E.g.: fine kitchen towels
and table cloths dry faster than the thick
bath towels.
Correct load capacity
Home articles
Approximate
weights (g)
Cotton quit covers (double)
Cotton quit covers (single)
Bed sheets (double)
Bed sheets (single)
Large tablecloths
Small tablecloths
Tea napkins
Bath towels
Hand towels
1500
1000
500
350
700
250
100
700
350
Approximate
weights (g)
150
300
200
500
350
700
100
125
Garments
Blouses
Cotton shirts
Shirts
Cotton dresses
Dresses
Jeans
Handkerchiefs (10 pieces)
T-Shirts
Loading the laundry
• Open the loading door.
• Place laundry items loosely into the dryer.
• Push the loading door to close. Ensure that
no items are caught in the door.
A
Consider the information in the
"Programme Selection Table". Always start
the programme in accordance with the
maximum load capacity.
CAdding laundry to the machine more
than the level shown in the figure is not
recommended. Drying performance will
9 EN
4 Selecting a Programme and Operating Your Machine
Control panel
1
2
4
3
7
6
5
1. Filter cleaning warning light
Warning light turns on when the filter is full.
2. Program follow-up indicator
Used to follow-up the progress of the current
programme.
3. Low temperature
Used to dry in low temperatures.
Low
Ventilation
temparature
Cottons Synthetics
Spin
Ready
to iron
4. On/Off button
Used to turn on and off the machine.
5. Programme selection knob
Used to select a programme.
6. Start/Pause/Cancel button
Used to start, pause or cancel the
programme.
7. Water tank warning light
Warning light turns on when the water tank is
full.
Ready to
Filter
wear
cleaning
10 EN
On/Off
Start Child-proof
pause
lock
cancel
Tank
full
Timer
follow-up
indicator
Preparing the machine
1. Plug in your machine.
2. Place the laundry in the machine.
3. Press the “On/Off” button.
CPressing the “On/Off” button does not
necessarily mean that the programme has
started. Press “Start/Pause/Cancel” button
of the machine to start the programme.
Timer program selection
Decide the appropriate time from the table
below which includes drying temperature in
degrees. Select the desired time with the timer
program selection button.
Extra dry
Ready to
wear
Iron Dry
C
Dry at high temperature only
for cotton laundry. Thick and
multi layered laundry (E.g.:
towels, linens, jeans) are dried
in a way that they do not
require ironing before placing
in the wardrobe.
Normal laundry (E.g.:
tablecloths, underwear) are
dried in a way that they do not
require ironing before placing
in the drawers.
Normal laundry (E.g., Shirts,
dresses) are dried ready to be
ironed.
For further program details, see, “Program
Selection Table”
Main programmes
Anti-creasing
A 2-hour anti creasing programme to prevent
laundry from creasing will be activated if
you do not take the laundry out after the
programme is over. This programme rotates
the laundry in 600-second intervals to prevent
creasing.
•Ventilation
Only ventilation is performed for 10 minutes
without blowing hot air. You can air your
clothes that have been kept at closed
environments for a long time thanks to this
program to deodorize unpleasant odors.
•Timer programs
You can select one of the 20 min...105
min...135 min... timer programs to achieve
the final drying level. Dry the cotton laundry
at high temperatures and synthetic and easycare laundry at low temperatures depending
on the type of the laundry.
C You must press the “Low temperature”
button for synthetics
11 EN
Program selection and consumption table
EN
Program table
Approximate
Programs
Capacity (kg)
Spin speed in washing
amount of
Drying time
machine (rpm)
remaining
(minutes)
humidity
Cottons / Coloreds
7
A
Ready to Wear
3.5
7
A
Ready to Iron
3.5
1000
% 60
135
800
% 70
150
1000
% 60
90
800
% 70
105
1000
% 60
105
120
800
% 70
1000
% 60
60
800
% 70
60-90
800
% 40
60
600
% 50
90
Synthetics
B
Ready to Wear
3.5
Energy consumption values
Approximate
Programs
Capacity (kg)
Spin speed in washing
amount of
machine (rpm)
remaining
humidity
Energy
consumption
value kWh
Cottons linen Ready to wear*
7
1000
% 60
4.48
Cottons Ready to iron
7
1000
% 60
3.40
3.5
800
% 40
1.60
Synthetics Ready to wear
* : Energy Label standard program (EN 61121:2005)
All values given in the table have been fixed according to EN 61121:2005 Standard. These
values may deviate from the table according to the laundry type, laundry spin speed,
environmental conditions and voltage fluctuations.
12 EN
Auxiliary function
Low temperature
This function allows for drying at lower
temperatures and therefore saves energy.
Warning LED will light up when you select the
function.
C You must use this function when you dry
your synthetic or delicate laundry.
Adding/removing laundry in standby
mode
In order to add or take out laundry after the
start-up of the program;
1. Press the “Start/Pause/Cancel” button to
switch the machine to “Pause” mode. Drying
process will stop.
Warning indicators
2. Open the door at Pause position and close it
CWarning indicators may differ according to the again after adding or taking out laundry.
model of your dryer.
3. Press “Start/Pause/Cancel” button to start the
Filter cleaning
program.
A warning light will turn on to remind filter
C
Any laundry added after the drying process
cleaning after the programme finishes.
was started may cause the already dried
CIf the filter cleaning warning light lights up
clothes in the machine intermingle with wet
continuously, please refer to, “Suggested
clothes and the result will be wet laundry after
solutions for problems”.
the drying process is over.
Water tank
AWarning LED will light up at the end of the
program or when the tank is full with water.
The machine stops operating when this
warning LED lights up during a program
running. To restart the machine, please drain
the water in the water tank. Press “Start/
Pause/Cancel” button to start the program
after you have emptied the water tank. The
warning LED goes off and the program
resumes operating.
Starting the programme
1. Press “Start/Pause/Cancel” button to start
the programme.
2. Light of the “Start/Pause/Cancel” button will
turn on to indicate that the programme has
started.
Child-proof lock
There is a childproof lock to prevent any
program interruption due to the pressing of keys
while the program is on. The loading door and
all keys except the “On/Off” key on the panel are
deactivated when the child-proof lock is active.
In order to activate the childproof lock, press
on the “Start/Pause/Cancel” and “Low
temperature” buttons simultaneously for 3
seconds.
To start a new program after the program is
over or to interrupt the program, the childproof
lock should be deactivated. To deactivate the
childproof lock, press the same buttons for 3
sec.
Timer follow-up indicator
One of the LEDs is on as far as program runs
and shows the approximate remaining time.
Changing the program after the
program has started
You can use this feature to dry your laundry in a
different program after your machine has started
to run.
For example;
Press and hold the “Start/Pause/Cancel” button
for about 3 seconds to select “90” minutes
program instead of “60” minutes program.
Select the “90” minutes program by rotating the
program knob.
Press “Start/Pause/Cancel” button to start the
program.
C The program which is selected first will
go on even if the program selection button
is moved and another program mode is
selected while the machine is operating. You
must cancel the ongoing program in order to
change the drying program. (See, Ending the
program through canceling)
COne of the LEDs on the program follow-up
indicator starts flashing when the child-proof
lock is activated.
C Child-proof lock is deactivated when the
machine is restarted by pressing the On/Off
button.
Ending the program through canceling
The program which is selected first will keep
on going even if the position of the program
selection button is changed. A new program
can be selected and started after “Program
cancel” is activated in order to change the drying
program.
To cancel any selected program;
• Press “Start/Pause/Cancel” button for about
a duration of 3 seconds. The “Filter cleaning”
and “Water tank” warning LEDs as well as the
13 EN
“0” warning LED on the program follow-up
indicator will light up at the end of this period
for reminding purposes.
A As the inside of the machine will be
excessively hot when you cancel the program
while the machine is running, activate the
ventilation program to cool it down.
The machine will not start even if the “Start/
Pause/Cancel” button is pressed, unless the
program selection knob is returned to the
initial program. The paused program must be
cancelled in order to change the drying program.
End of program
The “Filter cleaning” and “Water tank” warning
LEDs as well as the “0” warning LED on the
program follow-up indicator will light up at the
end of the program. The door can be opened
and the machine becomes ready for a second
cycle.
Press the “On/Off” button to shut down the
machine.
C A 2-hour anti creasing program to prevent
laundry from creasing will be activated if you
do not take the laundry out after the program
has come to an end.
C Clean the filter after each drying (please see,
Filter cleaning).
C Drain the water tank after each drying (please
see, Water tank)
14 EN
5 Maintenance and cleaning
Filter Cartridge / Door Inner Surface
Lint and fibres released from the laundry to the
air during the drying cycle are collected in the
“Filter Cartridge”.
*To drain the water tank:
1-Carefully remove the water tank by opening
the kick plate cover/pulling the drawer.
2-Drain the water in the tank
CSuch fibre and lint are generally formed
during wearing and washing.
CAlways clean the filter and the inner surfaces
of the cover after each drying process.
CYou can clean the filter and filter area by
vacuum cleaner.
To clean the filter:
1. Open the loading door.
2. Remove the cover filter by pulling it up and
open the filter.
3. Clean lint, fibre, and cotton raveling by hand
or with a soft piece of cloth.
4. Close the filter and place it back into its
seat.
C Clogging may arise on the filter surface after
using your machine for some time; if this
occurs, wash the filter with water and dry it
before using again.
C Clean the entire inner surface of the cover
and door gasket.
Water tank;
The moisture in the damp laundry is taken from
the laundry and condens ed. Drain the water
tank after each drying cycle or during drying
when “Water tank” warning light turns on.
ACondensed water is not drinkable!
ANever take out the water tank when the
programme is running!
If you forget to drain the water tank, your dryer
will stop during the following drying cycles
when the water tank is full and the “Water
tank” warning light will turn on. If this is the
case, press the “Start/Pause/Cancel” button to
resume the drying cycle after draining the water
tank.
3-If there is lint accumulation in the funnel of the
water tank, clean it under running water.
4-Place the water tank into its seat.
For the condenser;
Hot and humid air in the condenser is cooled
with the cold air from the room. Thus, the humid
air circulating in your dryer is condensed and
then pumped into the tank.
CClean the condenser after every 30 drying
cycles or once a month.
To clean the condenser:
1. If a drying process has been carried out, open
the door of the machine and wait until it cools
down.
15 EN
2. Unlock the 2 condenser locks after opening
the kick plate.
3. Pull out the condenser.
5. Place the condenser in its housing. Fasten
the 2 locks and make sure that they are
seated securely.
6. Close the kick plate cover.
4. Clean the condenser by applying
pressurized water with a shower armature
and wait until the water drains.
16 EN
6 Suggested solutions for problems
Drying process takes too much time
• Meshes of the filter may be clogged. Wash with water
Laundry comes out wet at the end of drying.
• Meshes of the filter may be clogged. Wash with water.
• Excessive laundry might have been loaded in. Do not load the dryer in excess.
Dryer does not switch on or the programme does not start. Dryer is not activated when set.
• It might have not been plugged in. Make sure that the machine is plugged in.
• The loading door may be ajar. Make sure that the loading door is properly closed.
• Programme might have not been set or the «Start/Pause/Cancel» button might have not
been pressed. Make sure that the programme has been set and it is not in “Pause” mode.
• «Childproof lock» might have been activated. Deactivate the childproof lock.
Programme has been interrupted without any cause.
• The loading door may be ajar. Make sure that the loading door is properly closed.
• Electricity may be cut off. Press «Start/Pause/Cancel» button to start the programme.
• Water may be full. Drain the water in the tank.
Laundry has shrunk, become felted or deteriorated.
• A programme suitable for the laundry type might have not been used. Dry only the laundry
which is suitable for drying in dryer after checking the labels on your clothes.
• Select a programme with suitable low temperature for the laundry type to dry your clothes.
Drum lightning does not come on. (For models with lamp)
• Dryer might have not been started by using the «On/Off» button. Make sure that the dryer is
on.
• Bulb may have blown. Call the authorized service to replace the bulb.
“0” LED flashes.
• The 2-hour anti creasing programme to prevent laundry from creasing might have been
activated. Turn off the dryer and take out the laundry.
“0” LED is on.
• Programme has come to an end. Turn off the dryer and take out the laundry.
“Filter cleaning” LED is on.
• Filter might have not been cleaned. Clean the cover filter.
“Water comes out the cover”
• Clean the entire inner surface of the cover and door gasket.
“Cover opens spontaneously.”
• Push it until you hear that it is closed.
For products with a condenser:
“Water tank” warning LED is on.
• Water may be full. Drain the water in the tank.
“Condenser cleaning” LED is on.
• Condenser might have not been cleaned. Clean the filters in the condenser under the kick
plate.
A Call an authorized service if the problem persists.
17 EN