- Computers & electronics
- TVs & monitors
- CRT TVs
- JVC
- AV-29BA16, AV-29MT16, AV-29ST16, AV-29VT16, AV-21BA16, AV-21MT16, AV-21VT16, AV-25MT16
- User's manual
advertisement
▼
Scroll to page 2
of 24
COLOR TELEVISION EQUALIZER • CINEMA SURROUND • COMPONENT INPUT Contents AV-29BA16 AV-29MT16 AV-29ST16 AV-29VT16 AV-25MT16 AV-21BA16 AV-21MT16 AV-21VT16 Knowing your TV’s features .......................................................3 Remote control buttons and basic functions ..............................4 TV buttons and functions............................................................6 Setting up your TV ......................................................................7 Basic setting for picture ..............................................................9 Advanced setting for picture ..................................................... 11 Basic setting for sound .............................................................12 Advanced setting for sound ......................................................13 DVD Menu ................................................................................15 Customized setting ...................................................................16 TV channel presetting ..............................................................18 Additional preparation ..............................................................19 Troubleshooting ........................................................................20 Specifications ...........................................................................21 INSTRUCTIONS GGT0121-001A-H GGT0121-001A-H.indd 1 23.06.2006 9:26:18 Uhr Thank you for buying this JVC color television. To make sure you understand how to use your new TV, please read this manual thoroughly before you begin. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO ENSURE PERSONAL SAFETY, OBSERVE THE FOLLOWING RULES REGARDING THE USE OF THIS TV. 1 Operate only from the power source indicated on the rear of the TV. 2 Avoid damaging the power cord and mains plug. When unplugging the TV, grasp the mains plug. Do not pull on the power cord. 3 Never block or cover the ventilation openings. Never install the TV where good ventilation is unattainable. When installing this TV, leave spaces for ventilation around the TV of more than the minimum distances as shown. 7 This TV can be turned on/off power by connecting/disconnecting the AC plug into AC outlet. While this TV is being installed, enough space should be reserved for connection/disconnecting the AC plug into AC outlet by hand. 8 The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. WARNING: <AV-21M, AV-25M, AV-29M, AV-21B, AV-29B Series> YOU CAN DETACH THE PROTECT SHEET ON THE TOP AND BOTTOM OF FRONT FRAME IF YOU NEEDED. THE FRONT BUTTON DOOR OF THE TV SHOULD BE PULLED OUT FROM ITS BOTTOM. DO NOT PRESS THE UPPER PART, OR YOUR FINGER MAY BE PINCHED. 15 cm 10 cm 10 cm 15 cm ✓ PULL PULL 4 Do not allow objects or liquid into the cabinet openings. 5 In the event of a fault, unplug the unit and call a service technician. Do not attempt to repair it yourself or remove the rear cover. 6 The surface of the TV screen is easily damaged. Be very careful with it when handling the TV. Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it forcefully. Never use any cleaner or detergent on it. 2 GGT0121-001A-H.indd 2 23.06.2006 9:26:19 Uhr Knowing your TV’s features Main features DVD MENU COLOR MaxxBass EXIT MTS CLOSED CAPTION FAVORITE CH (Channel) AI ECO SENSOR 100+ ECO MODE AI VOLUME VNR TINT MaxxBass — — PICTURE TILT 2 AI ECO SENSOR 2 ECO MODE MTS AV-21VT16 Function 1 AV-21MT16 Model No. NO. AV-21BA16 Confirm your TV’s functions Some functions written in this instruction manual may not be available for your TV. Please see the chart below and check the functions that are equipped for your TV’s model number. The model number is indicated at the rear of your TV. When you press a button concerned to a function that is not available for your TV, it does not work and the logo “Ø” appears on the screen. AV-25MT16 RM-C1287 BASS AV-29VT16 CINEMA SURROUND AV-29ST16 ECO AV-29MT16 VNR AV-29BA16 CLOSED CAPTION Just connect DVD player to the television. The television will detect DVD signal and display picture on the screen automatically and you can adjust pictures and sound while you are watching DVD as your desire. When disconnect DVD player, the television will display the previous channel. MaxxBass enhances bass sound that cannot be reproduced by normal speakers to be heard by our ears. You can listen the stereo sound or SAP from TV program broadcating by MTS system. (SAP: Second audio program.) You can display dialog on the screen from TV broadcasting with Closed caption system. You also may be able to display some information in text form if available. You can register up to four favorite channels for quick recall with one press. TV detects the brightness of your room and automatically adjust the picture brightness to a suitable level for a better eyecare. You can adjust TV screen contrast according to the brightness of your room to suitable level for a better eyecare. TV adjusts the volume automatically to the same level for all TV channels to avoid sudden change of the volume when selecting different TV channels or selecting Video Mode. You can reduce the picture noise when viewing noisy TV programs or video sources. You can adjust TINT setting for all color systems, including PAL. — O — — O O O O O — O O O O — O O O O — O — O O — — — — — O O — O O — O — O O — 3 GGT0121-001A-H.indd 3 23.06.2006 9:26:20 Uhr Remote control buttons and basic functions No. Press To 1 POWER Turn on or off the TV from standby mode. 2 MENU/OK Display menu and confirm selected function. 3 5/∞/2/3 Select and adjust menu function. 4 CHANNEL -/+ Select the desired channel number. 5 VOLUME -/+ Adjust the volume level. 6 TV/VIDEO EXIT Select TV or video terminal input. On the other hand, you can use this button to EXIT from the menu. 7 MUTING Turn off the volume. Press this button again to resume the volume. 8 DISPLAY /BACK Display the program number or video terminal number on the screen. On the other hand, you can use this button to return to the previous menu. 9 0~9, 100+ Select the program number. For three digits program number, press 100+, then press the number button. COLOR 1 # 8 EXIT 3 2 " 6 7 9 CLOSED CAPTION 100+ ! RETURN+ a) Return to the frequently view channel with one touch. 1 Choose the channel you want to register. 2 Press and hold RETURN+ button until “RETURN PLUS PROGRAMMED!” appears. To cancel, press and hold RETURN+ button until “RETURN PLUS CANCELED!” appears. b) Return to the previously viewed channel, if you have not set or have cancelled the Return channel as above. " CLOSED CAPTION Display information in text which are broadcasted by some TV channels. # FAVORITE CHANNEL (color buttons: red, green, yellow, blue) Register and recall 4 favorite channels. 1. Choose the TV channel you want to register then press and hold a color button until “PROGRAMMED! ■" appears. 2. To register other favorite channels, repeat step 1. To recall the favorite channel, press the color button. When the TV is in menu mode, the favorite channel function is not available. ! 4 5 VNR RM-C1287 4 GGT0121-001A-H.indd 4 23.06.2006 9:26:20 Uhr Remote control buttons and basic functions (continued) How to operate menus and menus locations To Display the MENU Note To exit the MENU, Press the MENU/OK button 2. PICTURE MENU is displayed on press the DISPLAY/ BACK button 8 or first press. choose EXIT menu or TV/VIDEO/EXIT button 6. Choose a Top menu Press 2/3 buttons 3 to choose a menu title when the cursor is pointing at MENU. Choose a 2nd menu Press 5/∞ buttons 3 to choose a Press ∞ button 3 2nd menu title. to display the next Press 5/∞ buttons 3 to choose a functions. Display the 3rd menu Operation — 2nd menu title. Then press MENU/ OK button 2. Press the DISPLAY/BACK button 8. Return to the — previous menu Choose the setting Press 5/∞ buttons 3 to choose Press the TV/ VIDEO/ of a function a function. Then press the 2/3 EXIT button 6 to exit buttons 3 to change the setting. from the menu. Adjust the effect Press 5/∞ buttons 3 to choose level of a function a function. Then press the 2/3 buttons 3 to adjust the effect level. Display the sub Press the 5/∞ buttons 3 to menu of a function. choose a function. Then press — MENU/OK button 2 to display the sub menu. The following chart shows locations of functions in menus. In this manual, location of a function is described as follows: MENU Top menu 2nd menu MENU Top menu 2nd menu 3rd menu Note: Some functions have the 4th menus as the sub-menus. Top menu MENU PICTURE SOUND FEATURES 2nd menu PICTURE MODE PICTURE SETTING OFF TIMER CHILD LOCK COMPRESS (16:9) AI ECO SENSOR/ ECO MODE AUTO PROGRAM CHANNEL SUMMARY COLOR SYSTEM VIDEO-2 SETTING BLUE BACK CLOSED CAPTION Location 3nd menu P.9 – P.10 PICTURE BRIGHT DETAIL COLOR TINT P.10 – P.16 – P.13 – P.14 – P.12 – P.14 – P.12 – P.13 – P.13 – P.15 AUTO SIGNAL DETECT DVD PICTURE MODE DVD THEATER STATUS DVD SOUND MODE P.16 CH ON TIMER P.17 – P.16 – P.11 – P.11 – Location – P.10 P.10 P.10 P.10 P.10 – – – – – – – – – P.15 P.15 P.15 P.15 P.16 P.16 – – – – P.18 P.18 P.9 P.17 P.11 P.16 PICTURE TILT BEEP P.11 P.17 – – – – – P.16 P.16 – – WHITE BALANCE VNR MTS AI VOLUME SOUND MODE EQUALIZER BALANCE CINEMA SURROUND MaxxBass DVD MENU ON TIMER INSTALL – – – – – CAPTION TEXT – – 5 GGT0121-001A-H.indd 5 23.06.2006 9:26:22 Uhr TV buttons and functions The illustrations shown below is for AV-21BA16 and AV-29ST16 only, which are used for explanation purpose. Your TV may not look exactly the same as illustrated. No. Button/terminal 1 L (main power) 2 POWER lamp Front of the TV AV-29ST16 POWER 3 4 5 6 7 8 9 ! TV/VIDEO R MENU/OK IN(VIDEO-3) L/MONO CHANNEL V VOLUME AV-21BA16 Description Page Press to turn on or turn off the TV’s main power. – Indicate the TV’s status. – No color : TV’s main power is being turned off. Red : TV’s main power is being turned on. Blink : While the TV is in standby mode, ON TIMER funciton is in used. While the TV is in turn on mode , OFF TIMER function is in used. Note: When you turn off the power switch while TV is in standby mode, the power lamp will go off in 10 -15 seconds. When you operate the TV, POWER Lamp will be blink. ECO sensor – Remote control sensor – TV/VIDEO Press to select TV or Video terminal input or exit from menu. – VOLUME -/+ Press to adjust the volume level. – CHANNEL -/+ Press to select the desired channel (Both of RF and Video input.) – MENU/OK Press to display the menu. – IN (VIDEO-3) Video and audio input jacks for VIDEO-3 mode. 19 Headphone jack. 19 " Aerial socket. 7 # OUTPUT Video and audio output jacks. (The component video signal cannot be output.) Video or component video, and audio input jacks for VIDEO-2 mode. You can select the input signal by setting the “VIDEO-2 SETTING” function (see page 17). Video or S-VIDEO, and audio input jacks for VIDEO-1 mode. 19 POWER V L / MONO IN (VIDEO-3) Rear of the TV AV-29ST16 6)$%/ ).054 #/-0/.%.4 6)$%/ /54054 ).054 3 R MENU OK CHANNEL VOLUME $ COMPONENT (VIDEO-2) INPUT % VIDEO-1 INPUT 19 7 How to operate the menus with the TV button TV button Work as same as the button on Note the remote control unit MENU MENU/OK button CHANNEL -/+ VOLUME -/+ ∞/5 button 2/3 button /6%2 6 6 9 6 , -/./ #" , 2 #2 2 -/./ , 2 To display main menu and exit menu after finish setting. To select menu function. To choose a Top menu and adjust the desired menu function. 6 GGT0121-001A-H.indd 6 23.06.2006 9:26:22 Uhr Setting up your TV CAUTION • Turn off the equipment including the TV before connecting. 1 Connecting the aerial cable. 2 Connecting the main plug to the AC outlet. 3 Inserting batteries into the remote control. Insert two batteries by following the + and - polarities and inserting the - end first. CAUTION: Follow the cautions printed on the batteries. Notes: • Use AA/R6/UM-3 dry cell batteries. • If the remote control does not work properly, fit new batteries. The supplied batteries are for testing, not regular use. 4 Turn on the TV by pressing the main power button. JVC logo appears on the screen. (1) VHF/UHF outdoor aerial Matching aerial adapter (supplied) (2) (3) 75-ohm coaxial cable (not supplied) If you connect a VCR, connect the aerial output jack of your VCR and the aerial jack on the TV with aerial cable. Then connect the output jacks of your VCR and the VIDEO-1 input jacks of the TV with the video cable (or S-VIDEO cable if available) and audio cables. For details, see the manual of your VCR. Rear of TV VHF/UHF outdoor aerial AV-29ST16 VIDEO-1 INPUT COMPONENT (VIDEO-2) OUTPUT INPUT S OVER V V Y/ V L/ MONO CB L/ R CR R MONO L R JVC logo will appear on the screen again at the phase of “SETUP TOUR RESTART?” function. Then the initial setting can be performed according to page 8. VCR The illustration shown is just a sample. It may not be same as your TV. Note: While in the INSTALL menu with the cursor pointing at INSTALL, pressing the blue button will also display the JVC logo. 7 GGT0121-001A-H.indd 7 23.06.2006 9:26:24 Uhr Setting up your TV (continued) 5 Making the initial settings Set up your TV by pressing MENU/OK button or waiting for 15 seconds, then operate the TV by following the steps below: AUTO PROGRAM AUTO PROGRAM AIR CABLE 10% MENU : OK DISPLAY : BACK TV/VIDEO : EXIT • Press 5/∞ button or CH +/- key to select AIR or CABLE, press the MENU/OK button. MENU : OK MENU : OK • TV will start searching for the channels. To stop AUTO PROGRAM, press MENU/OK button. AUTO PROGRAM CHANNEL SUMMARY CH/CC CH 02 ■ CH 03 ■ CH 04 ■ CH 05 ■ CH 06 CH 07 CH 08 When turn on the TV at the next time SKIP SETUP TOUR RESTART? ■SKIP ■CANCEL • To complete the initial setting, press the MENU/OK button. To set undesired channels to be skipped, see page 18. ■ : YES MENU : NO • “SETUP TOUR RESTART?” will be displayed. Press the MENU/OK button to cancel the SETUP TOUR RESTART function. If you want to make initial settings again when the next time you turn on the TV, press the Red button to activate the SETUP TOUR RESTART function. 8 GGT0121-001A-H.indd 8 23.06.2006 9:26:24 Uhr Basic setting for picture PICTURE MODE COLOR SYSTEM You can select the appropriate color system when the picture is not clear or no color appears. Press the COLOR SYSTEM button to select a setting. In TV mode: NTSC 3.58 MHz (Fixed). In VIDEO mode: AUTO PAL SECAM NTSC3.58 You can choose the desired picture setting with one-touch. Press the PICTURE MODE button to select a setting. SOFT BRIGHT STANDARD USER NTSC4.43 To operate this function with a menu: MENU INSTALL menu COLOR SYSTEM For the color system in each country or region, see the table below: Area Asia, Middle East Europe Oceania Africa Country or Region System When you select VIDEO-2 Mode, you cannot adjust DETAIL. When you set DVD THEATER STATUS in DVD MENU to ON, you cannot adjust PICTURE MODE. To operate this function with a menu: MENU Bahrain, Kuwait, Oman, Qatar, United Arab Emirates, Yemen, etc. Indonesia, Malaysia, Singapore, Thailand, India, etc. PAL China, Vietnam, etc. PAL Hong Kong, etc. PAL Islamic Republic of Iran, Lebanon, Saudi Arabia, etc. SECAM Philippines, Taiwan, Myanmar, etc. NTSC Russia, etc. SECAM Czech Republic, Poland, etc. PAL Germany, Holland, Belgium, etc. PAL UK, etc. PAL Australia, New Zealand, etc. PAL Republic of South Africa, etc. PAL Nigeria, etc. PAL Egypt, Morocco, etc. SECAM Softens contrast and sharpness. Heightens contrast and sharpness. Standard picture setting. You can change this picture setting as you like. Select USER and adjust following items in the PICTURE SETTING menu. (PICTURE, BRIGHT, DETAIL, COLOR, TINT) PICTURE menu PICTURE MODE To return the USER setting to default, press the blue button when the PICTURE SETTING menu is displayed. About the basic operations of the menu, please see the “How to operate menus and menus locations” on page 5. 9 GGT0121-001A-H.indd 9 23.06.2006 9:26:25 Uhr Basic setting for picture (continued) PICTURE SETTING WHITE BALANCE You can adjust the desired picture setting when selecting USER in PICTURE MODE. 1 Select USER in PICTURE MODE under PICTURE menu. MENU USER PICTURE menu PICTURE MODE MENU 2 Select PICTURE SETTING in PICTURE menu, then adjust the setting. MENU PICTURE BRIGHT DETAIL COLOR TINT You can change the white balance of the picture to better match the type of video being viewed. Select WHITE BALANCE in the PICTURE menu, then choose the desired setting. PICTURE menu 2 : Lower contrast 2 : Darker 2 : Softer 2 : Lighter 2 : Reddish PICTURE SETTING 3 : Higher contrast 3 : Brighter 3 : Higher 3 : Deeper 3 : Greenish NORMAL COOL WARM PICTURE menu WHITE BALANCE Normal white balance. Bluish white. Reddish white. When you set DVD THEATER STATUS in DVD MENU to ON, you cannot adjust WHITE BALANCE. When you select VIDEO-2 Mode, you cannot adjust DETAIL. About the basic operations of the menu, please see the “How to operate menus and menus locations” on page 5. 10 GGT0121-001A-H.indd 10 23.06.2006 9:26:26 Uhr Advanced setting for picture AI ECO SENSOR (ECO)/ECO MODE You can adjust TV screen contrast according to the brightness of your room. Press the ECO button to select the desired mode. OFF MODE-1/ECO-1 MODE-2/ECO-2 DISPLAY (for AI ECO SENSOR only) Cancel the function. Mild contrast (recommended.) Even contrast. Display the graphic of the function. To operate this function with a menu: MENU 2 Press the 5/∞ buttons until the picture becomes level. Then press the MENU/OK button. COMPRESS (16:9) You can convert a normal picture (4:3 aspect ratio) into a wide picture (16:9 aspect ratio). Select COMPRESS (16:9) in the FEATURES menu, then choose ON or OFF. MENU FEATURES menu FEATURES menu COMPRESS (16:9) AI ECO SENSOR / ECO MODE When you set DVD THEATER STATUS in DVD MENU to ON, you cannot adjust AI ECO SENSOR / ECO MODE. Note : AI ECO SENSOR for M and S series. ECO MODE for B series. Correcting the Slanting Picture (PICTURE TILT) You can correct the picture tilt caused by the earth’s magnetic force. 1 Select PICTURE TILT in the INSTALL menu, then press MENU/ OK button. MENU INSTALL menu The following display appears. PICTURE TILT BLUE BACK You can set the TV to automatically change to a blue screen and mute the sound if the signal is weak or absent, or when there is no input from an antenna. Select BLUE BACK in the INSTALL menu, then choose ON or OFF. MENU INSTALL menu BLUE BACK If you wish to continue viewing the poor picture, off the BLUE BACK function. PICTURE TILT MENU : OK DISPLAY : BACK TV/VIDEO : EXIT About the basic operations of the menu, please see the “How to operate menus and menus locations” on page 5. 11 GGT0121-001A-H.indd 11 23.06.2006 9:26:27 Uhr Basic setting for sound SOUND MODE You can choose the desired sound setting. Select the SOUND MODE in SOUND menu, then choose the setting. MENU SOUND menu SOUND MODE USER You can change this sound setting as you like. Select USER and adjust the frequencies in EQUALIZER (100, 300, 1K, 3K, 8K Hz). For details, see “EQUALIZER” on page 14. SOUND TURBO Emphasize on low and high frequency levels. THEATER Emphasize on movie sound. MUSIC Emphasize on music effect. NEWS Emphasize on vocal sound. When you select VIDEO-2, you cannot adjust SOUND MODE function. You can adjust it in DVD Menu. When SOUND MODE is set to SOUND TURBO, EQUALIZER, CINEMA SURROUND and MaxxBass functions are not available. BALANCE You can adjust the volume balance between the left and right speakers. Select BALANCE in SOUND menu, then adjust the setting. MENU SOUND menu BALANCE About the basic operations of the menu, please see the “How to operate menus and menus locations” on page 5. 12 GGT0121-001A-H.indd 12 23.06.2006 9:26:27 Uhr Advanced setting for sound CINEMA SURROUND MTS You can enjoy an enhanced sound for wider audience. Press the CINEMA SURROUND button to select a setting. OFF ON Cancel the function. Listen to sound with wider audience effect. This function is not available when SOUND MODE is set to SOUND TURBO. To operate this function with a menu: MENU SOUND menu You can enjoy the stereo and SAP broadcasted programs. Select the MTS in SOUND menu, then choose the desired mode. MENU STEREO SAP MONO SOUND menu MTS Select stereo sound. Select second audio programs. Select monaural sound. This function is not available in video mode. CINEMA SURROUND MaxxBass You can enjoy an enhanced bass sound which cannot be reproduced by normal speakers. Select MaxxBass in SOUND menu, then choose the desired setting. MENU OFF HIGH LOW SOUND menu MaxxBass MaxxBass is turned off. MaxxBass effect is high. MaxxBass effect is low. This function is not available when SOUND MODE is set to SOUND TURBO. “MaxxBass” is a registered trademark of Waves Audio Ltd. in the USA, Japan and other countries. About the basic operations of the menu, please see the “How to operate menus and menus locations” on page 5. 13 GGT0121-001A-H.indd 13 23.06.2006 9:26:28 Uhr Advanced setting for sound (continued) EQUALIZER AI VOLUME You can adjust the sound level of each frequencies when selecting USER mode in SOUND MODE. 1 Select USER in SOUND MODE under SOUND menu. MENU SOUND MODE SOUND menu USER 2 Select EQUALIZER in SOUND menu. MENU You can adjust the volume of all the channels and video inputs to the same level automatically depends on the strength of signal of the sources. Select AI VOLUME in SOUND menu, then choose ON or OFF. MENU SOUND menu AI VOLUME EQUALIZER SOUND menu The following display appears. 100 1K IIIIIIII IIIIIII 300 IIIIIIIIIIIIIIII IIIIIIIIIIIIIIII EQUALIZER 3K 8K Hz MENU : OK DISPLAY : BACK TV/VIDEO : EXIT 3 Select and adjust the desired frequencies. 4 Press the MENU/OK button to exit the menu. Adjust high frequency will affect higher pitch sound and vice versa. When you select VIDEO-2, you cannot adjust EQUALIZER. When you set DVD SOUND MODE in DVD MENU to USER, you can adjust EQUALIZER under SOUND menu. 14 GGT0121-001A-H.indd 14 About the basic operations of the menu, please see the “How to operate menus and menus locations” on page 5. 23.06.2006 9:26:28 Uhr DVD Menu AUTO SIGNAL DETECT ON When the DVD input signal is detected, the input mode will be changed to VIDEO-2 automatically. And when the DVD input signal is not detected, the input mode will be changed to RF previous input mode. Select AUTO SIGNAL DETECT in DVD MENU under FEATURES menu then choose ON or OFF (Factory setting is ON). FEATURES menu MENU AUTO SIGNAL DETECT DVD MENU Press the “POWER ON” button on the DVD players or VCRs (follow by the “PLAY” button for VCRs) so that the signal can be detected. DVD PICTURE MODE You can enhance the picture quality of the DVD or VIDEO-2. Select DVD PICTURE MODE in DVD MENU under FEATURES menu, then choose the desired setting. MENU FEATURES menu DVD PICTURE MODE OFF CLEAR-1 CLEAR-2 DVD MENU Cancel the function. Select when the disc is with lots of noise (To soften the picture). Select when the disc is with less noise (To sharpen the picture). Enjoy movie playback with suitable color temperature, sharp subtitles and improved gradation for black, like in a theater. Cancel the function. OFF When you set DVD THEATER STATUS to ON, PICTURE MODE, WHITE BALANCE and AI ECO SENSOR / ECO MODE functions are not available. DVD SOUND MODE You can choose different sound setting for viewing different types of DVD content. Select DVD SOUND MODE in DVD MENU under FEATURES menu, then choose the desired setting. MENU FEATURES menu DVD MENU DVD SOUND MODE MUSIC USER DRAMA THEATER Select when watching a music concert. Select if you want to adjust the sound setting to your preference. Select when watching a drama movie. Select when watching an action movie. When you set DVD SOUND MODE in DVD MENU to USER, you can adjust EQUALIZER under SOUND menu. DVD THEATER STATUS You can enjoy an enhanced picture quality for movie playback in a dark room, like watching a movie in the theater. Select DVD THEATER STATUS in DVD MENU under FEATURES menu, then choose ON or OFF. MENU FEATURES menu DVD THEATER STATUS DVD MENU About the basic operations of the menu, please see the “How to operate menus and menus locations” on page 5. 15 GGT0121-001A-H.indd 15 23.06.2006 9:26:29 Uhr Customized setting VNR CHILD LOCK You can reduce the picture noise. Select VNR in PICTURE menu, then choose a setting of VNR function. MENU OFF AUTO MIN MAX PICTURE menu VNR VNR is turned off. Effect of VNR is automatically controlled. Effect of VNR becomes minimum level. Effect of VNR becomes maximum level. If you select MAX, the picture becomes softer even if the original picture is sharp. When you select VIDEO-2, you cannot adjust VNR function. CHILD LOCK ON TIMER You can set the TV to turn on automatically from standby mode at a set channel and time. 1 Select ON TIMER in the FEATURE menu. FEATURES menu ON TIMER If they are included in a program, you can view closed captions or ON TIMER CH ON TIMER 02 00:15 The following display appears. DISPLAY : BACK TV/VIDEO : EXIT text information. Press the CLOSED CAPTION button to select a setting. CLOSED CAPTION TEXT To operate this function with a menu: 1 Select the CLOSED CAPTION in INSTALL menu, then choose “CAPTION” or “TEXT”. MENU FEATURES menu MENU MENU CLOSED CAPTION OFF You can disable the front control buttons of the TV. Select CHILD LOCK in the FEATURES menu, then choose ON or OFF. INSTALL menu CLOSED CAPTION 2 Press the 2/3 button to select the desired caption or text channel. 2 Choose the CH (channel) by pressing the 2/3 button. External input, AV position and any un-preset channel cannot be chosen for CH. 3 Set the ON TIMER to your desired period of time by pressing the 2/3 button. ON TIMER starts. You can set the period of time to a maximum of 12 hours in 15-minute intervals. To off the ON TIMER, set the ON TIMER to OFF. Note : If TV is not in standby mode when ON TIMER is reach the setting time, this case is not available. About the basic operations of the menu, please see the “How to operate menus and menus locations” on page 5. 16 GGT0121-001A-H.indd 16 23.06.2006 9:26:30 Uhr Customized setting (continued) OFF TIMER BEEP You can set the TV to turn off automatically to standby mode after a set time. Press the OFF TIMER button to select a desired period of time. You can set the period of time to a maximum of 120 minutes in 10 minute intervals. MENU To operate this function with a menu: MENU FEATURES menu You can use the BEEP function to alert you during AUTO SIGNAL DETECT, AI ECO SENSOR Detect, Stereo Detect, ON TIMER/OFF TIMER operations and when some buttons on the remote control are pressed. Select BEEP in the INSTALL menu, then choose ON or OFF. OFF TIMER INSTALL menu BEEP When the volume is level 0, then BEEP function is not available. When the remaining elapse time is one minute, “GOOD NIGHT!” appears on the screen. You can display the OFF TIMER menu again to confirm or change the remaining time. DISPLAY VIDEO-2 SETTING You can set the VIDEO-2 SETTING according to the video signal output from external devices connected to the VIDEO-2 terminal. Select VIDEO-2 SETTING in INSTALL menu, then choose a setting (Factory setting is COMPONENT). MENU VIDEO COMPONENT INSTALL menu You can display the program number and video terminal number on the screen. Press the DISPLAY button to display the indication on the screen. VIDEO-2 SETTING If a normal video signal (composite video signal) is input. If a component video signal (Y/CB/CR) is input. You must choose a setting according to the signal that you input to VIDEO-2. (If you input the VIDEO Signal or VCR Signal to VIDEO-2, you must set VIDEO-2 SETTING to VIDEO.) For connecting methods, see “Additional Preparation” on page 19. About the basic operations of the menu, please see the “How to operate menus and menus locations” on page 5. 17 GGT0121-001A-H.indd 17 23.06.2006 9:26:31 Uhr TV channel presetting To register the TV channels automatically (AUTO PROGRAM) 2 Choose CHANNEL SUMMARY, then press the MENU/OK button. CHANNEL SUMMARY menu appears. You can register the TV channels into the TV’s channel list automatically. CHANNEL SUMMARY 1 Display the INSTALL menu. MENU CH/CC CH 02 ■ CH 03 ■ CH 04 ■ CH 05 ■ CH 06 CH 07 CH 08 INSTALL menu 2 Choose AUTO PROGRAM, then press the MENU/OK button. 3 Press the 5/∞ button to select AIR or CABLE, then press the MENU/OK button. ■SKIP ■CANCEL 3 Choose the channel which you want to skip. 4 CHANNEL SUMMARY ✔ ✔ MENU : OK AUTO PROGRAM function starts, and the channels received are registered automatically. 4 The CHANNEL SUMMARY menu appears. SKIP 5 The skip can be set to all channels of AIR (CH02-CH69) and CABLE (CC01-CC125). Press the yellow button to skip the channel. To cancel the skip, press the blue button. Press the MENU/OK button to exit the menu. You can set undesired channels to be skipped. Channels are to be skipped cannot be selected by the CHANNEL -/+ button. 1 Display the INSTALL menu. MENU INSTALL menu About the basic operations of the menu, please see the “How to operate menus and menus locations” on page 5. 18 GGT0121-001A-H.indd 18 23.06.2006 9:26:31 Uhr Additional preparation The illustrations shown in this section are for AV-21BA16 and AV29ST16 only, which are used for explanation purpose. Your TV may not look exactly the same as illustrated. Connecting to rear component/video input terminals and output terminals Rear of TV Before connecting • Read the manuals provided with the devices for the proper connection. • Turn off all the devices including the TV. • Note that connecting cables are not supplied. Connecting to front video input terminals Front of TV AV-29ST16 VIDEO-1 INPUT R Camcorder or TV game VCR (for playing) DVD player (composite signals) S VCR (for recording) OVER V AV-29ST16 COMPONENT (VIDEO-2) OUTPUT INPUT V Y/ V L/MONO IN(VIDEO-3) L/ MONO CB L/ R CR R MONO L R DVD player (component video signals) V When connecting to COMPONENT (VIDEO-2) input, depending on the connection, choose the appropriate video input using the menu (see “VIDEO-2 SETTING” on page 17) AV-21BA16 Headphones V L / MONO IN (VIDEO-3) R MENU OK C 19 GGT0121-001A-H.indd 19 23.06.2006 9:26:32 Uhr Troubleshooting If a problem occurs when you are using the TV, check the below troubleshooting guide before calling for repair. • No picture, no sound • Deactivate the BLUE BACK function if it is turned on. • Color patches appear at the corner of the screen • Stripes appear on the • Interference occurs caused by other devices such as picture an amplifier, personal computer, or a hair drier. Move such devices away from your TV. • This may due to the magnetized device such as a speaker near to your TV. Keep the device apart from your TV. Alternately, you can also use the magneticshielded speaker. • Picture is tilted • This may due to the earth magnetism. Refer to “PICTURE TILT” on page 11 to correct the tilt. • Double-pictures (ghosting) occur • Interference occurs caused by signal reflecting from mountains or building. Try to adjust the aerial’s direction or use a better directionality antenna. • Image takes a short • Image required time to stabilize before display. This period to be displayed is not a malfunction. • Poor picture • Choose the appropriate color system. Refer to “COLOR SYSTEM” on page 9. • Adjust the COLOR or BRIGHT setting. Refer to “PICTURE SETTING” on page 10. • TV may emit crackling • This is due to a sudden change in temperature sound and it is not a malfunction. If the crackling sound is too frequent, request your service technician for inspection. • White and bright still image look as if it were colored • Inevitable phenomenon due to the nature of the picture tube. This is not a malfunction. • Feel a slight electric shock when touching the TV screen • This is due to the static electricity of the picture tube and it will not harm the human body. This is not a malfunction. • Top of the image from • This is due to the condition of the video signal whereby software products or the image was not recorded properly. This is not a video tape is distorted malfunction. • The Auto Signal Detect function does not work • Please check that the AUTO SIGNAL DETECT function is on or off. • Turn the VCR or DVD player off, wait a while, then turn it on again. • Inspect the video cable connection on VIDEO-2 that they are connected properly. • Snowy picture • Poor sound • Check the aerial cable and its connection with the TV. • Adjust the sound frequency properly. Refer to “EQUALIZER” on page 14. • Stereo or SAP sound • TV channel reception is poor. Change the stereo/ SAP is unclear mode to mono sound (see page 13). • Cannot operate the remote control • The batteries may be exhausted. Replace with new batteries (see page 7). • Ensure that you are operating the remote control at less than seven meters from the front of your TV. • Cannot operate the menus • Press TV/VIDEO button to return to TV mode and try operating the menus. • Cannot operate the front control buttons • Deactivate the CHILD LOCK function if it is turned on (see page 16). • Suddenly, a channel • Some VCRs and DVD players can trigger Auto Signal Detect even after you choose a different input. or input was changed to VIDEO-2 • Please turn off the AUTO SIGNAL DETECT inputs. function. • “PLEASE DISCONNECT VIDEO-1 CABLE!” appears on the screen. • Please disconnect either S-VIDEO cable or video input cable from Video-1 input. 20 GGT0121-001A-H.indd 20 23.06.2006 9:26:33 Uhr Specifications TV RF systems M Color systems TV mode: NTSC 3.58 MHz VIDEO mode: PAL, SECAM, NTSC 3.58 MHz, NTSC 4.43 MHz Receiving channels VHF low channel (VL), VHF high channel (VH), UHF channel (U) Receives cable channels in mid band, super band and hyper band. Power requirements AC 110 to 240 V, 50 Hz / 60 Hz External input / output VIDEO-1: S-video input, VIDEO input, AUDIO L/R input VIDEO-2/COMPONENT: VIDEO input, AUDIO L/R input, COMPONENT VIDEO (Y/CB/CR) input VIDEO-3: VIDEO input, AUDIO L/R input OUTPUT: VIDEO output, AUDIO L/R output Headphone jack: Stereo mini jack (3.5 mm diameter) Sound-multiplex systems MTS (Multi-channel Television Sound) (Except AV-29BA16, AV-21BA16) AV STEREO (For AV-29BA16, AV-21BA16 only) Viewing Screen Size (Visible area) AV-21BA16 508 mm AV-21MT16 508 mm AV-21VT16 508 mm AV-25MT16 600 mm AV-29BA16 676 mm AV-29MT16 676 mm AV-29VT16 676 mm AV-29ST16 676 mm Design and specifications subject to change without notice. 21 GGT0121-001A-H.indd 21 23.06.2006 9:26:34 Uhr MEMO 22 GGT0121-001A-H.indd 22 23.06.2006 9:26:35 Uhr MEMO 23 GGT0121-001A-H.indd 23 23.06.2006 9:26:35 Uhr © 2006 Victor Company of Japan, Limited GGT0121-001A-H.indd 24 0606-FLE-JMT 23.06.2006 9:26:35 Uhr
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project