Having TROUBLE with operation?
ENGLISH
Please reset your unit
FRANÇAIS
Refer to page of How to reset your unit
Vous avez des PROBLÈMES de fonctionnement?
Réinitialisez votre appareil
Référez-vous à la page intitulée Comment réinitialiser votre appareil
KD-R412 / KD-R411 /
KD-R35 / KD-R312 / KD-R311
CD RECEIVER / RÉCEPTEUR CD
Dear Customer,
This apparatus is in conformance with the valid
European directives and standards regarding
electromagnetic compatibility and electrical safety.
European representative of Victor Company of
Japan, Limited is:
JVC Technical Services Europe GmbH
Postfach 10 05 04
61145 Friedberg
Germany
Cher(e) client(e),
Cet appareil est conforme aux directives et
normes européennes en vigueur concernant la
compatibilité électromagnétique et à la sécurité
électrique.
Représentant européen de la société Victor
Company of Japan, Limited:
JVC Technical Services Europe GmbH
Postfach 10 05 04
61145 Friedberg
Allemagne
For canceling the display demonstration, see page 4. / Pour annuler la démonstration des
affichages, référez-vous à la page 4.
For installation and connections, refer to the separate manual. / Pour l’installation et les
raccordements, se référer au manuel séparé.
INSTRUCTIONS
MANUEL D’INSTRUCTIONS
EN, FR
© 2009 Victor Company of Japan, Limited
CoverRear_KD-R412_003A_f.indd 1-2
GET0624-003A
1009DTSMDTJEIN
[E/EU]
10/13/09 11:51:18 AM
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and
to obtain the best possible performance from the unit.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave
all servicing to qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with
optical instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
Warning:
Battery
Products
Information for Users on Disposal of
Old Equipment and Batteries
[European Union only]
These symbols indicate that the product and
the battery with this symbol should not be
disposed as general household waste at its
end-of-life.
If you wish to dispose of this product and
the battery, please do so in accordance with
applicable national legislation or other rules
in your country and municipality.
By disposing of this product correctly, you
will help to conserve natural resources and
will help prevent potential negative effects
on the environment and human health.
Notice:
The sign Pb below the symbol for batteries
indicates that this battery contains lead.
2
If you need to operate the unit while driving,
be sure to look around carefully or you may be
involved in a traffic accident.
For safety...
• Do not raise the volume level too much, as
this will block outside sounds, making driving
dangerous.
• Stop the car before performing any
complicated operations.
Temperature inside the car...
If you have parked the car for a long time in
hot or cold weather, wait until the temperature
in the car becomes normal before operating
the unit.
KD-R412/KD-R411 is equipped with the
steering wheel remote control function.
Before operating, connect a JVC's OE remote
adapter (not supplied) which matches your car
to the steering wheel remote input terminal on
the rear of the unit.
• For details, refer also to the instructions
supplied with the remote adapter.
ENGLISH
EN02-09_KD-R412_003A_f.indd 2
10/15/09 2:32:58 PM
How to read this manual
The following icons/symbols are used to
indicate:
CONTENTS
3 How to read this manual
3 How to attach/detach the control
Press and hold the button(s)
[Hold]
until the desired operation
begins.
Turn the control dial.
Turn the control dial
to make a selection,
then press to confirm.
(
XX)
<XXXX>
Reference page number
Menu setting item
Continued on the next page
How to attach/detach the control
panel
panel
3 How to reset your unit
3 How to forcibly eject a disc
4
Canceling the display
demonstration
4
5
6
8
10
Setting the clock
Basic operations
Listening to the radio
Listening to a disc
Listening to the USB device
(For KD-R412/KD-R411/KD-R35)
11
Listening to the other external
components
12
Using the remote controller
(For KD-R412/KD-R411)
How to reset your unit
Your preset adjustments
will also be erased.
13
13
17
20
21
24
Selecting a preset sound mode
Menu operations
More about this unit
Maintenance
Troubleshooting
Specifications
How to forcibly eject a disc
[Hold]
• You can forcibly eject the loaded disc even
if the disc is locked. To lock/unlock the disc,
8.
• Be careful not to drop the disc when it ejects.
• If this does not work, reset your unit.
ENGLISH
EN02-09_KD-R412_003A_4.indd 3
3
10/12/09 9:59:13 AM
Canceling the display demonstration
1 Turn on the power.
4 Select <DEMO OFF>.
2
5
[Hold]
(Initial setting)
3
6 Finish the procedure.
Setting the clock
1 Turn on the power.
2
6 Adjust the minute.
[Hold]
(Initial setting)
3 Select <CLOCK>.
7 Select <24H/12H>.
4 Select <CLOCK SET>.
8 Select <24 HOUR> or
<12 HOUR>.
5 Adjust the hour.
9 Finish the procedure.
4
ENGLISH
EN02-09_KD-R412_003A_4.indd 4
10/12/09 9:59:13 AM
Basic operations
Ejects the disc
Control dial
Display window
Loading slot
Detaches the panel
Auxiliary input jack
Remote sensor (for KD-R412/KD-R411)
You can control this unit with an
optionally purchased remote control,
12).
RM-RK50 (
For KD-R412/
KD-R411/KD-R35
USB (Universal Serial
Bus) input jack
When you press or hold the following button(s)...
Button
General operation
• Turns on.
• Selects the available sources (if the power is turned on). If the source is ready,
playback also starts.
• Turns off if pressed and held.
• Adjusts the volume level.
• Selects items.
• Mutes the sound while listening to a source. If the source is “CD“ or “USB,“
playback pauses. Press the control dial again to cancel muting or resume
playback.
• Confirms selection.
• Selects the sound mode.
• Enters tone level adjustment directly (
Enters playback mode menu directly (
13) if pressed and held.
9).
• Returns to the previous menu
• Activates/deactivates TA Standby Reception
• Enters PTY Searching mode if pressed and held
Power off : Checks the current clock time
Power on : Changes the display information
ENGLISH
EN02-09_KD-R412_003A_5.indd 5
5
10/13/09 12:49:11 PM
Listening to the radio
~
] “FM” or “AM”
Ÿ
“ST” lights up when receiving an FM stereo broadcast with sufficient signal strength.
Manual search
Automatic presetting (FM)—
“M” flashes, then press
the button repeatedly.
[Hold]
SSM (Strong-station Sequential Memory)
You can preset up to 18 stations for FM.
While listening to a station...
When an FM stereo broadcast is
hard to receive
1
[Hold]
2
] <TUNER> ] <MONO> ]
<MONO ON>
Reception improves, but stereo effect
will be lost.
To restore the stereo effect, repeat the same
procedure to select <MONO OFF>.
1
[Hold]
2
] <TUNER> ] <SSM> ]
<SSM 01 – 06> / <SSM 07 – 12> /
<SSM 13 – 18>
“SSM” flashes and local stations with
the strongest signals are searched and
stored automatically.
To preset another 6 stations, repeat the
above procedure by selecting one of the other
6 SSM setting ranges.
Changing the display information
Frequency = Clock = (back to
the beginning)
6
ENGLISH
EN02-09_KD-R412_003A_5.indd 6
10/13/09 12:49:39 PM
Manual presetting (FM/AM)
You can preset up to 18 stations for FM and 6
stations for AM.
Ex.: Storing FM station of 92.50 MHz into preset
number “04.”
1
] “92.50MHz”
2
[Hold]
The following features are available
only for FM Radio Data System stations.
Searching for your favourite
FM Radio Data System
programme—PTY Search
You can tune in to a station broadcasting your
favourite programme by searching for a PTY
code.
1
“PRESET MODE” flashes.
3
[Hold]
The last selected PTY code appears.
2
] Selects preset number “04.”
“P04” flashes and “MEMORY” appears.
Selecting a preset station
1
or
2
] Select one of your favourite
programme types or a PTY code (
and start searching.
17),
If there is a station broadcasting a
programme of the same PTY code as you
have selected, that station is tuned in.
Standby receptions
TA Standby Reception
TA Standby Reception allows the unit to switch
temporarily to Traffic Announcement (TA) from
any source other than AM.
• The volume changes to the preset TA volume
level if the current level is lower than the
preset level (
15).
To activate TA Standby Reception
If the TP indicator lights up, TA
Standby Reception is activated.
If the TP indicator flashes, TA
Standby Reception is not yet
activated.
• To activate the reception, tune in to another
station providing Radio Data System signals
required for TA Standby Reception.
• To deactivate the reception, press T/P BACK
again.
ENGLISH
EN02-09_KD-R412_003A_5.indd 7
7
10/12/09 10:31:57 AM
PTY Standby Reception
PTY Standby Reception allows the unit to
switch temporarily to your favourite PTY
programme from any source other than AM.
To activate and select your favourite PTY
code for PTY Standby Reception, see “Menu
14)
operations: <PTY-STANDBY>.” (
If the PTY indicator lights up, PTY Standby
Reception is activated.
If the PTY indicator flashes, PTY Standby
Reception is not yet activated.
• To activate the reception, tune in to another
station providing these signals.
• To deactivate the reception, select <PTY OFF>
for the PTY code (
14). The PTY indicator
goes off.
Tracing the same programme—
Network-Tracking Reception
When driving in an area where FM reception is
not sufficient enough, this unit automatically
tunes in to another FM Radio Data System
station of the same network, possibly
broadcasting the same programme with
stronger signals.
Programme A broadcasting on different
frequency areas (01 – 05)
To change the Network-Tracking Reception
setting, see “Menu operations: <AF-REG>.”
(
14)
Automatic station selection—
Programme Search
Usually when you select a preset number, the
station preset in that number is tuned in.
If the signals from the FM Radio Data System
preset station are not sufficient for good
reception, this unit, using the AF data, tunes in
to another frequency possibly broadcasting the
same programme as the original preset station
is broadcasting.
• See “Menu operations: <P-SEARCH>.” (
15)
Changing the display information
Station name (PS) = Station
Frequency = Programme
type (PTY) = Clock = (back to
the beginning)
Listening to a disc
] Turn on the power.
~
Ÿ
All tracks will be played repeatedly until you
change the source or eject the disc.
Stopping playback and ejecting
the disc
“NO DISC” appears.
Press / SOURCE to listen to
another playback source.
8
Prohibiting disc ejection
[Hold]
To cancel the prohibition, repeat the same
procedure.
ENGLISH
EN02-09_KD-R412_003A_4.indd 8
10/12/09 9:59:15 AM
Selecting the playback modes
Selects folder of the MP3/WMA
You can use only one of the following playback
modes at a time.
1
Selects track
[Hold]
2
Fast-forwards or
reverses the track
] “REPEAT”
“RANDOM”
3
Selecting a track/folder
1
2
For MP3/WMA discs, select the desired folder,
then the desired track by repeating step 2.
• To return to the previous menu, press BACK.
REPEAT
TRACK RPT : Repeats current track
FOLDER RPT : Repeats current folder
RANDOM
FOLDER RND : Randomly plays all tracks
of current folder, then
tracks of next folders
ALL RND
: Randomly plays all tracks
To cancel repeat play or random play, select
“RPT OFF” or “RND OFF.”
Caution on volume setting:
Discs produce very little noise compared
with other sources. Lower the volume before
playing a disc to avoid damaging the speakers
by the sudden increase of the output level.
Changing the display information
Disc title/Album name/performer (folder
name)* = Track title (file name)* = Current
track number with the elapsed playing time
= Current track number with the clock
time = (back to the beginning)
* If the current disc is an audio CD, “NO NAME”
appears.
If an MP3/WMA file does not have Tag
information or <TAG DISPLAY> is set to
<TAG OFF> (
14), folder name and file name
appear.
ENGLISH
EN02-09_KD-R412_003A_5.indd 9
9
10/12/09 10:32:22 AM
Listening to the USB device (For KD-R412/KD-R411/KD-R35)
This unit can play MP3/WMA tracks stored in a USB device.
~
Ÿ
USB input jack
USB memory
] Turn on the
power.
All tracks will be played repeatedly until you change the
source or detach the USB device.
If a USB device has been attached...
Pressing / SOURCE turns on the power and
playback starts from where it has been stopped
previously.
• If a different USB device is currently attached,
playback starts from the beginning.
Stopping playback and detaching
the USB device
Straightly pull it out from the unit.
“NO USB” appears. Press / SOURCE to listen to
another playback source.
You can operate the USB device in the same
way you operate the files on a disc.
Caution on volume setting:
USB devices produce very little noise compared
with other sources. Lower the volume before
playing a USB to avoid damaging the speakers
by sudden increase of the output level.
10
Cautions:
• Avoid using the USB device if it might hinder
your safety driving.
• Do not pull out and attach the USB device
repeatedly while “READING” is shown on the
display.
• Do not start the car engine if a USB device is
connected.
• This unit may not be able to play the files
depending on the type of USB device.
• Operation and power supply may not work as
intended for some USB devices.
• You cannot connect a computer to the USB
input terminal of the unit.
• Make sure all important data has been backed
up to avoid losing the data.
• Do not leave a USB device in the car, expose
to direct sunlight, or high temperature to
avoid deformation or cause damages to the
device.
• Some USB devices may not work immediately
after attaching USB device or turn on the
power.
• For more details about USB operations, see
page 19.
ENGLISH
EN10-17_KD-R412_003A_f.indd 10
10/15/09 2:29:43 PM
Listening to the other external
components
You can connect an external component to the
AUX (auxiliary) input jack on the control panel.
Preparation: Make sure <AUX ON> is selected
for the <SRC SELECT> = <AUX IN> setting.
(
16)
• For details, refer also to the instructions
supplied with the adapter or external
components.
~
Ÿ
!
⁄
] “AUX IN”
Turn on the connected component
and start playing the source.
] Adjust the volume.
Adjust the sound as you
want. ( 13)
Connecting an external component to the AUX input jack
Portable audio player,
etc.
3.5 mm stereo mini plug
(not supplied)
ENGLISH
EN10-17_KD-R412_003A_4.indd 11
11
10/12/09 9:59:00 AM
Using the remote controller (For KD-R412/KD-R411)
KD-R412/KD-R411 can be remotely controlled
as instructed here (with an optionally
purchased remote controller). We recommend
that you use remote controller RM-RK50 with
your unit.
Installing the lithium coin battery
(CR2025)
Caution:
• Danger of explosion if battery is incorrectly
replaced. Replace only with the same or
equivalent type.
• Battery shall not be exposed to excessive heat
such as sunshine, fire, or the like.
If the effectiveness of the remote controller
decreases, replace the battery.
Before using the remote controller:
• Aim the remote controller directly at the
remote sensor on the unit.
• DO NOT expose the remote sensor to bright
light (direct sunlight or artificial lighting).
Remote sensor
12
1 • Turns the power on if pressed briefly.
When the power is on, pressing the
button also mutes the sound or pauses.
To cancel muting or resume playback,
press the same button again.
• Turns the power off if pressed and held.
2 • Changes the preset stations.
• Changes the folder of the MP3/WMA.
3 Adjusts the volume level.
4 Selects the sound mode.
5 Selects the source.
6 • Searches for stations if pressed briefly.
• Fast-forwards or reverses the track if
pressed and held.
• Changes the tracks if pressed briefly.
Warning (to prevent accidents and
damage):
• Do not install any battery other than CR2025
or its equivalent.
• Do not leave the remote controller in a place
(such as dashboards) exposed to direct
sunlight for a long time.
• Store the battery in a place where children
cannot reach.
• Do not recharge, short, disassemble, heat the
battery, or dispose of it in a fire.
• Do not leave the battery with other metallic
materials.
• Do not poke the battery with tweezers or
similar tools.
• Wrap the battery with tape and insulate when
throwing away or saving it.
ENGLISH
EN10-17_KD-R412_003A_4.indd 12
10/12/09 9:59:00 AM
Selecting a preset sound mode
You can select a preset sound mode suitable
for the music genre.
Storing your own sound mode
You can store your own adjustments in memory.
1
FLAT = NATURAL = DYNAMIC = VOCAL
BOOST = BASS BOOST = USER = (back to
the beginning)
2
] <PRO EQ> ] <BASS> / <MIDDLE> /
<TREBLE>
While listening, you can adjust the tone level of
the selected sound mode.
1
[Hold]
3
[Hold]
2
Adjust the level (–06 to +06) of the
selected tone (BASS / MIDDLE / TREBLE).
The sound mode is automatically stored
and changed to “USER.”
4
Adjust the sound elements of the
selected tone. (
19)
Repeat steps 2 and 3 to adjust other
tones.
The adjustments made will be stored
automatically in “USER.”
The current sound mode changes to “USER”
automatically.
Menu operations
1
[Hold]
CLOCK
DEMO
Category
Menu item
DEMO
Display
demonstration
CLOCK SET
Clock setting
2
3
Repeat step 2 if necessary.
• To return to the previous menu,
press BACK.
• To exit from the menu, press DISP
or MENU.
Selectable setting, [ Initial: Underlined ]
• DEMO ON
: Display demonstration will be activated
automatically if no operation is done for about
20 seconds. (
4)
• DEMO OFF : Cancels.
[ 0:00 ]
4)
: Adjust the hour, then the minute. (
ENGLISH
EN10-17_KD-R412_003A_4.indd 13
13
10/12/09 9:59:00 AM
PRO EQ
CLOCK
Category
Menu item
24H/12H
Time display
mode
CLOCK ADJ *1
Clock
adjustment
BASS
MIDDLE
TREBLE
DIMMER
DISPLAY
SCROLL *2
TUNER
TAG DISPLAY
SSM *3
Strong-station
Sequential
Memory
AF-REG *4
Alternative
frequency/
regionalization
reception
PTYSTANDBY *3, *4
*1
*2
*3
*4
14
Selectable setting, [ Initial: Underlined ]
• 24 HOUR
• 12 HOUR
: For settings,
• AUTO
: The built-in clock is automatically adjusted
using the CT (clock time) data in the Radio Data
System signal.
: Cancels.
13.
: For settings,
• OFF
—
4.
• DIMMER ON : Dims the display and button illumination.
• DIMMER OFF : Cancels.
• SCROLL ONCE : Scrolls the displayed information once.
• SCROLL AUTO : Repeats scrolling (at 5-second intervals).
• SCROLL OFF : Cancels.
Pressing DISP for more than one second can scroll the display
regardless of the setting.
• TAG ON
: Shows the Tag information while playing MP3/
WMA tracks.
• TAG OFF
: Cancels.
• SSM 01 – 06 : For settings,
6.
• SSM 07 – 12
• SSM 13 – 18
• AF ON
• AF-REG ON
• OFF
• PTY OFF, PTY
codes
: When the currently received signals become
weak, the unit switches to another station (the
programme may differ from the one currently
received). (The AF indicator lights up.)
: When the currently received signals become
weak, the unit switches to another station
broadcasting the same programme. (The AF
and REG indicators light up.)
: Cancels.
: Activates PTY Standby Reception with one of
the PTY codes (
17).
Takes effect only when CT (clock time) data is received.
Some characters or symbols will not be shown correctly (or will be blanked) on the display.
Displayed only when the source is “FM.”
Only for FM Radio Data System stations.
ENGLISH
EN10-17_KD-R412_003A_4.indd 14
10/12/09 9:59:01 AM
Category
Menu item
TUNER
TA VOLUME *5
Traffic
announcement
volume
P-SEARCH *5
Programme
search
MONO *7
Monaural mode
IF BAND
Intermediate
frequency band
Selectable setting, [ Initial: Underlined ]
• VOLUME 00 – : —
VOLUME 50 (or
VOLUME 00 –
VOLUME 30) *6
[ VOLUME 15 ]
• SEARCH ON
: Activates Programme Search. (
• SEARCH OFF
: Cancels.
• MONO ON
• MONO OFF
• AUTO
• WIDE
FADER *8
AUDIO
BALANCE *9
LOUD
Loudness
AUX ADJUST *10
Auxiliary adjust
(For KD-R312/
KD-R311)
R06 – F06
[ 00 ]
L06 – R06
[ 00 ]
• LOUD ON
• LOUD OFF
AUX ADJ 00 —
AUX ADJ 05
8)
: Activate monaural mode to improve FM
reception, but stereo effect will be lost.
: Restore the stereo effect. (
6)
: Increases the tuner selectivity to reduce
interference noises between adjacent
stations. (Stereo effect may be lost.)
: Subject to interference noises from adjacent
stations, but sound quality will not be
degraded and the stereo effect will remain.
: Adjust the front and rear speaker output
balance.
: Adjust the left and right speaker output
balance.
: Boost low and high frequencies to produce a
well-balanced sound at a low volume level.
: Cancels.
: Adjust the auxiliary input level to avoid the
sudden increase of the output level when
changing the source to external component
connected to the AUX input jack on the
control panel.
*5 Only for FM Radio Data System stations.
*6 Depends on the amplifier gain control.
*7 Displayed only when the source is “FM.”
*8 If you are using a two-speaker system, set the fader level to “00.”
*9 For KD-R412/KD-R411/KD-R312/KD-R311: This adjustment will not affect the subwoofer output.
*10 Displayed only when <AUX IN> is set to <AUX ON>.
ENGLISH
EN10-17_KD-R412_003A_4.indd 15
15
10/12/09 9:59:01 AM
Category
Menu item
VOL ADJUST
Volume adjust
(For KD-R412/
KD-R411/KD-R35)
AUDIO
L/O MODE *11
Line output mode
SUB.W FREQ *11, *12
Subwoofer cutoff
frequency
SUB.W LEVEL *11, *12
Subwoofer level
BEEP
TEL MUTING
Telephone muting
SRC
SELECT
AMP GAIN *13
Amplifier gain
control
AM *14
AM station
AUX IN *15
Auxiliary input
Selectable setting, [ Initial: Underlined ]
VOL ADJ –05 — : Preset the volume adjustment level of
VOL ADJ +05
each source (except FM), compared to the
[ VOL ADJ 00 ]
FM volume level. The volume level will
automatically increase or decrease when
you change the source.
• Before making an adjustment, select the
source you want to adjust.
• “VOL ADJ FIX” appears on the display if
“FM” is selected as the source.
• SUB.W
: Select if the REAR LINE OUT terminals are
used for connecting a subwoofer (through
an external amplifier).
• REAR
: Select if the REAR LINE OUT terminals are
used for connecting the speakers (through
an external amplifier).
• LOW
: Frequencies lower than 72 Hz are sent to the
subwoofer.
• MID
: Frequencies lower than 111 Hz are sent to
the subwoofer.
• HIGH
: Frequencies lower than 157 Hz are sent to
the subwoofer.
: Adjust the subwoofer output level.
SUB.W 00 —
SUB.W 08
[ SUB.W 04 ]
• BEEP ON
: Activates the keypress tone.
• BEEP OFF
: Deactivates the keypress tone.
: Select either one which mutes the sounds
• MUTING 1/
MUTING 2
while using a mobile phone.
• MUTING OFF : Cancels.
• LOW POWER : VOLUME 00 – VOLUME 30 (Select if the
maximum power of each speaker is less than
50 W to prevent damaging the speakers.)
• HIGH POWER : VOLUME 00 – VOLUME 50
• AM ON
: Enable “AM” in source selection.
• AM OFF
: Disable “AM” in source selection.
• AUX ON
: Enable “AUX IN” in source selection.
• AUX OFF
: Disable “AUX IN” in source selection.
*11 For KD-R412/KD-R411/KD-R312/KD-R311.
*12 Displayed only when <L/O MODE> is set to <SUB.W>.
*13 The volume level automatically changes to “VOLUME 30” if you change to <LOW POWER> with the
volume level is set higher than “VOLUME 30.”
*14 Displayed only when any source other than “AM” is selected.
*15 Displayed only when any source other than “AUX IN” is selected.
16
ENGLISH
EN10-17_KD-R412_003A_4.indd 16
10/12/09 9:59:01 AM
More about this unit
Basic operations
Disc operations
General
Caution for DualDisc playback
• If you turn off the power while listening to
a track, playback will start from where it had
been stopped previously next time you turn
on the power.
• If no operation is done for about 60 seconds
after pressing MENU button, the operation will
be canceled.
• The Non-DVD side of a “DualDisc” does not
comply with the “Compact Disc Digital Audio”
standard. Therefore, the use of Non-DVD side
of a DualDisc on this product may not be
recommended.
Tuner operations
Storing stations in memory
• During SSM search...
– All previously stored stations are erased and
the stations are stored anew.
– When SSM is over, the station stored in the
lowest preset number will be automatically
tuned in.
• When storing a station manually, the
previously preset station is erased when a new
station is stored in the same preset number.
FM Radio Data System operations
• Network-Tracking Reception requires two
types of Radio Data System signals—PI
(Programme Identification) and AF
(Alternative Frequency) to work correctly.
• If a Traffic Announcement is received by
TA Standby Reception, the volume level
automatically changes to the preset level (TA
VOLUME) if the current level is lower than the
preset level.
• When Alternative Frequency Reception is
activated (with AF selected), Network-Tracking
Reception is also activated automatically.
• PTY codes: NEWS, AFFAIRS, INFO, SPORT,
EDUCATE, DRAMA, CULTURE, SCIENCE,
VARIED, POP M (music), ROCK M (music), EASY
M (music), LIGHT M (music), CLASSICS, OTHER
M (music), WEATHER, FINANCE, CHILDREN,
SOCIAL, RELIGION, PHONE IN, TRAVEL,
LEISURE, JAZZ, COUNTRY, NATION M (music),
OLDIES, FOLK M (music), DOCUMENT
General
• This unit has been designed to reproduce
CDs/CD Texts, and CD-Rs (Recordable)/CDRWs (Rewritable) in audio CD (CD-DA), MP3
and WMA formats.
• If you change the source while listening to a
disc, playback stops. Next time you select “CD”
as the playback source, playback will start
from where it had been stopped previously.
• When a disc is inserted upside down, “PLEASE”
and “EJECT” appear alternately on the display.
Press 0 to eject the disc.
• If the ejected disc is not removed within
15 seconds, it is automatically inserted into
the loading slot again to protect it from dust.
• MP3 and WMA “tracks” (words “file” and “track”
are used interchangeably) are recorded in
“folders.”
• While fast-forwarding or reversing on an MP3
or WMA disc, you can only hear intermittent
sounds.
Playing a CD-R or CD-RW
• Use only “finalized” CD-Rs or CD-RWs.
• This unit can only play back files of the same
type as those detected first if a disc includes
both audio CD (CD-DA) files and MP3/WMA
files.
• This unit can play back multi-session discs;
however, unclosed sessions will be skipped
while playing.
ENGLISH
EN10-17_KD-R412_003A_4.indd 17
17
10/12/09 9:59:01 AM
• Some CD-Rs or CD-RWs may not play back on
this unit because of their disc characteristics,
or for the following reasons:
– Discs are dirty or scratched.
– Moisture condensation has occurred on the
lens inside the unit.
– The pickup lens inside the unit is dirty.
– The files on the CD-R/CD-RW are written
using the “Packet Write” method.
– There are improper recording conditions
(missing data, etc.) or media conditions
(stained, scratched, warped, etc.).
• CD-RWs may require a longer readout time
since the reflectance of CD-RWs is lower than
that of regular CDs.
• Do not use the following CD-Rs or CD-RWs:
– Discs with stickers, labels, or a protective seal
stuck to the surface.
– Discs on which labels can be directly printed
by an ink jet printer.
Using these discs under high temperature
or high humidity may cause malfunctions or
damage to the unit.
Playing an MP3/WMA disc
• This unit can play back MP3/WMA files with
the extension code <.mp3> or <.wma>
(regardless of the letter case—upper/lower).
• This unit can show the names of albums,
artists (performer), and Tag (Version 1.0, 1.1,
2.2, 2.3, or 2.4) for MP3 files and for WMA files.
• This unit can display only one-byte characters.
No other characters can be correctly
displayed.
• This unit can play back MP3/WMA files
meeting the conditions below:
– Bit rate:
MP3: 32 kbps — 320 kbps
WMA: 32 kbps — 192 kbps
18
– Sampling frequency of MP3:
32 kHz, 44.1 kHz, 48 kHz (for MPEG-1)
16 kHz, 22.05 kHz, 24 kHz (for MPEG-2)
– Sampling frequency of WMA:
22.05 kHz, 32 kHz, 44.1 kHz, 48 kHz
– Disc format: ISO 9660 Level 1/Level 2,
Romeo, Joliet, Windows extension
• The maximum number of characters for
file/folder names (includes 4 extension
characters—<.mp3> or <.wma>): 12 — 128
characters (depending on the media used,
etc.).
• This unit can recognize a total of 512 files, 255
folders, and 8 hierarchical levels.
• This unit can play back files recorded in VBR
(variable bit rate).
Files recorded in VBR have a discrepancy
in the elapsed time display, and do not
show the actual elapsed time. In particular,
this difference becomes noticeable after
performing the search function.
• This unit cannot play back the following files:
– MP3 files encoded in MP3i and MP3 PRO
format.
– MP3 files encoded in an inappropriate
format.
– MP3 files encoded with Layer 1/2.
– WMA files encoded in lossless, professional,
and voice format.
– WMA files which are not based upon
Windows Media ® Audio.
– WMA files copy-protected with DRM.
– Files which have data such as AIFF, ATRAC3,
etc.
• The search function works but search speed is
not constant.
ENGLISH
EN18-25_KD-R412_003A_f.indd 18
10/15/09 12:15:29 PM
Playing MP3/WMA tracks from a
USB device (for KD-R412/KD-R411/
KD-R35)
• While playing from a USB device, the playback
order may differ from other players.
• This unit may be unable to play back some
USB devices or some files due to their
characteristics or recording conditions.
• Depending on the shape of the USB devices
and connection ports, some USB devices may
not be attached properly or the connection
might be loose.
• Connect one USB mass storage class device to
the unit at a time. Do not use a USB hub.
• If the connected USB device does not have
the correct files, “CANNOT PLAY” appears.
• This unit can show Tag (Version 1.0, 1.1, 2.2,
2.3, or 2.4) for MP3 files and for WMA files.
• This unit can play back MP3/WMA files
meeting the conditions below:
– Bit rate of MP3/WMA: 32 kbps — 320 kbps
– Sampling frequency of MP3:
32 kHz, 44.1 kHz, 48 kHz (for MPEG-1)
16 kHz, 22.05 kHz, 24 kHz (for MPEG-2)
– Sampling frequency of WMA:
22.05 kHz, 32 kHz, 44.1 kHz, 48 kHz
• This unit can play back MP3 files recorded in
VBR (variable bit rate).
• The maximum number of characters for:
– Folder names : 32 characters
– File names : 32 characters
– MP3 Tag : 64 characters
– WMA Tag : 32 characters
• This unit can recognize a total of 5 000 files,
255 folders (255 files per folder including
folder without unsupported files), and of 8
hierarchies.
• This unit does not support SD card reader.
• This unit cannot recognize a USB device
whose rating is other than 5 V and exceeds
500 mA.
• USB devices equipped with special functions
such as data security functions cannot be
used with the unit.
• Do not use a USB device with 2 or more
partitions.
• This unit may not recognized a USB device
connected through a USB card reader.
• This unit may not play back files in a USB
device properly when using a USB extension
cord.
• This unit cannot play back the following files:
– MP3 files encoded with MP3i and MP3 PRO
format.
– MP3 files encoded in an inappropriate
format.
– MP3 files encoded with Layer 1/2.
– WMA files encoded in lossless, professional,
and voice format.
– WMA files not based on Windows Media®
Audio.
Preset sound mode
Tone
BASS
MIDDLE
TREBLE
Sound element
Frequency
Level
60 Hz –06 to +06
80 Hz
100 Hz
200 Hz
0.5 kHz –06 to +06
1.0 kHz
1.5 kHz
2.5 kHz
10.0 kHz –06 to +06
12.5 kHz
15.0 kHz
17.5 kHz
Q
Q1.0
Q1.25
Q1.5
Q2.0
Q0.75
Q1.0
Q1.25
Q FIX
ENGLISH
EN18-25_KD-R412_003A_5.indd 19
19
10/13/09 1:54:42 PM
Maintenance
How to clean the connectors
To keep discs clean
Frequent detachment will deteriorate the
connectors.
To minimize this possibility, periodically wipe
the connectors with a cotton swab or cloth
moistened with alcohol, being careful not to
damage the connectors.
A dirty disc may not play
correctly. If a disc does become
dirty, wipe it with a soft cloth
in a straight line from center to
edge.
• Do not use any solvents (for example,
conventional record cleaner, spray, thinner,
benzine, etc.) to clean discs.
Connectors
Moisture condensation
Moisture may condense on the lens inside the
unit in the following cases:
• After starting the heater in the car.
• If it becomes very humid inside the car.
Should this occur, the unit may malfunction.
In this case, eject the disc and leave the unit
turned on for a few hours until the moisture
has evaporated.
To play new discs
New discs may have some
rough spots around the inner
and outer edges. If such a disc
is used, this unit may reject the
disc.
To remove these rough spots, rub the edges
with a pencil or ball-point pen, etc.
Do not use the following discs:
Single CD (8 cm disc)
Warped disc
How to handle discs
Center holder
When removing a disc
from its case, press down
the center holder of the case
and lift the disc out, holding
it by the edges.
• Always hold the disc by the edges. Do not
touch its recording surface.
When storing a disc in its case, gently insert
the disc around the center holder (with the
printed surface facing up).
• Make sure to store discs in cases after use.
Sticker and sticker
residue
Stick-on label
Unusual shape
C-thru Disc
(semitransparent
disc)
Transparent or
semitransparent
parts on its recording
area
20
ENGLISH
EN18-25_KD-R412_003A_4.indd 20
10/12/09 9:59:27 AM
Troubleshooting
Symptom
Sound cannot be heard from the
speakers.
• Adjust the volume to the optimum level.
• Make sure the unit is not muted/paused (
• Check the cords and connections.
“PROTECT” appears on the display
and no operations can be done.
Check to be sure the terminals of the speaker leads
are covered with insulating tape properly, then
reset the unit (
3).
If “PROTECT” does not disappear, consult your JVC
IN-CAR ENTERTAINMENT dealer or a company
supplying kits.
The unit does not work at all.
Reset the unit. (
“AUX” cannot be selected.
Check the <SRC SELECT> = <AUX IN> setting.
(
16)
SSM automatic presetting does
not work.
Store stations manually.
Static noise while listening to the
radio.
Connect the aerial firmly.
“AM” cannot be selected.
Check the <SRC SELECT> = <AM> setting. (
Disc cannot be played back.
Insert the disc correctly.
• CD-R/CD-RW cannot be played
back.
• Tracks on the CD-R/CD-RW
cannot be skipped.
• Insert a finalized CD-R/CD-RW.
• Finalize the CD-R/CD-RW with the component
which you used for recording.
Disc can neither be played back
nor ejected.
• Unlock the disc. (
8)
• Eject the disc forcibly. (
Disc sound is sometimes
interrupted.
• Stop playback while driving on rough roads.
• Change the disc.
• Check the cords and connections.
“NO DISC” appears on the display.
Insert a playable disc into the loading slot.
“PLEASE” and “EJECT“ appear
alternately on the display.
Press 0, then insert a disc correctly.
General
FM/AM
Disc playback
Remedy/Cause
5).
3)
16)
3)
ENGLISH
EN18-25_KD-R412_003A_4.indd 21
21
10/12/09 9:59:27 AM
MP3/WMA playback
Symptom
22
Remedy/Cause
Disc cannot be played back.
• Use a disc with MP3/WMA tracks recorded in a format
compliant with ISO 9660 Level 1, Level 2, Romeo, or
Joliet.
• Add the extension code <.mp3> or <.wma> to the
file names.
Noise is generated.
Skip to another track or change the disc. (Do not add
the extension code <.mp3> or <.wma> to non-MP3 or
WMA tracks.)
A longer readout time is
required (“READING” keeps
flashing on the display).
Do not use too many hierarchical levels and folders.
Tracks do not play back in the
order you have intended them
to play.
The playback order is determined when the files are
recorded.
For KD-R412/KD-R411/KD-R35:
Selected folder is an empty folder *. Select another
“NO FILE” appears on the display. folder that contains MP3/WMA tracks.
* Folder that is physically empty or folder that contains
data but does not contain valid MP3/WMA track.
“NOT SUPPORT” appears on the
display and track skips.
Skip to the next track encoded in an appropriate
format or to the next non-copy-protected WMA track.
The elapsed playing time is not
correct.
This sometimes occurs during playback. This is caused
by how the tracks are recorded on the disc.
The correct characters are not
displayed (e.g. album name).
This unit can only display letters (upper case), numbers,
and a limited number of symbols.
ENGLISH
EN18-25_KD-R412_003A_f.indd 22
10/16/09 5:48:38 PM
USB device playback (for KD-R412/KD-R411/KD-R35)
Symptom
Remedy/Cause
Noise is generated.
The track played back is not an MP3/WMA track. Skip to
another file. (Do not add the extension code <.mp3> or
<.wma> to non-MP3 or WMA tracks.)
“READING” keeps flashing on
the display.
• Readout time varies depending on the USB device.
• Do not use too many hierarchy or folders.
• Turn off the power then on again.
• Reattach the USB device again.
“NO FILE” appears on the
display.
Selected folder is an empty folder*. Select another
folder that contains MP3/WMA tracks.
* Folder that is physically empty or folder that contains
data but does not contain valid MP3/WMA track.
“NOT SUPPORT” appears on the Skip to the next track encoded in an appropriate format
display and track skips.
or to the next non-copy-protected WMA track.
Tracks/folders are not played
back in the order you have
intended.
The playback order is determined by the write-in time
stamp. The first track/folder written into the USB device
will be the first track/folder for playback.
• “CANNOT PLAY” flashes on
the display.
• “NO USB” appears on the
display.
• The unit cannot detect the
USB device.
• Attach a USB device that contains tracks encoded in
an appropriate format.
• Reattach the USB device again.
The correct characters are not
displayed (e.g. album name).
This unit can only display letters (upper case), numbers,
and a limited number of symbols.
While playing a track, sound is
sometimes interrupted.
The MP3/WMA tracks have not been properly copied
into the USB device.
Copy MP3/WMA tracks again into the USB device, and
try again.
JVC bears no responsibility for any loss of the data in the USB mass storage class device
while using this System.
ENGLISH
EN18-25_KD-R412_003A_4.indd 23
23
10/12/09 9:59:27 AM
Specifications
Maximum Power Output:
Continuous Power Output (RMS):
AUDIO AMPLIFIER SECTION
Load Impedance:
Tone Control Range:
Bass:
Middle:
Treble:
Frequency Response:
Signal-to-Noise Ratio:
Line-Out Level/Impedance:
Subwoofer-Out Level/Impedance:
Output Impedance:
Other Terminal:
Frequency Range:
TUNER SECTION
FM Tuner:
MW Tuner:
LW Tuner:
24
Front/
Rear:
Front/
Rear:
Except
KD-R35:
Except
KD-R35:
50 W per channel
19 W per channel into 4 Ω, 40 Hz to
20 000 Hz at no more than 0.8% total
harmonic distortion.
4 Ω (4 Ω to 8 Ω allowance)
±12 dB (60 Hz, 80 Hz, 100 Hz, 200 Hz)
Q1.0, Q1.25, Q1.5, Q2.0
±12 dB (0.5 kHz, 1.0 kHz, 1.5 kHz, 2.5 kHz)
Q0.75, Q1.0, Q1.25
±12 dB (10.0 kHz, 12.5 kHz, 15.0 kHz,
17.5 kHz)
Q (Fixed)
40 Hz to 20 000 Hz
70 dB
2.5 V/20 kΩ load (full scale)
2.5 V/20 kΩ load (full scale)
1 kΩ
• AUX (auxiliary) input jack, Aerial input
• For KD-R412/KD-R411: Steering wheel remote
input, USB input Jack
• For KD-R35: USB input Jack
FM:
87.5 MHz to 108.0 MHz
AM:
MW:
522 kHz to 1 620 kHz
LW:
144 kHz to 279 kHz
Usable Sensitivity:
9.3 dBf (0.8 μV/75 Ω)
50 dB
16.3 dBf (1.8 μV/75 Ω)
Quieting Sensitivity:
Alternate Channel
65 dB
Selectivity (400 kHz):
Frequency Response:
40 Hz to 15 000 Hz
Stereo Separation:
40 dB
Sensitivity:
20 μV
Selectivity:
40 dB
Sensitivity:
50 μV
ENGLISH
EN18-25_KD-R412_003A_4.indd 24
10/12/09 9:59:27 AM
GENERAL
USB SECTION
(for KD-R412/
KD-R411/KD-R35)
CD PLAYER SECTION
Type:
Signal Detection System:
Compact disc player
Non-contact optical pickup
(semiconductor laser)
Number of Channels:
2 channels (stereo)
Frequency Response:
5 Hz to 20 000 Hz
Dynamic Range:
93 dB
Signal-to-Noise Ratio:
98 dB
Wow and Flutter:
Less than measurable limit
MP3 Decoding Format: (MPEG1/2 Audio Layer 3) Max. Bit Rate: 320 kbps
WMA (Windows Media® Audio) Decoding Format: Max. Bit Rate: 192 kbps
USB Standard:
USB 1.1, USB 2.0
Data Transfer Rate (Full Speed):
Max. 12 Mbps
Compatible Device:
Mass storage class
Compatible File System:
FAT 32/16/12
Playable Audio Format:
MP3/WMA
500 mA
Max. Current:
DC 5 V
Power Requirement:
Operating Voltage:
DC 14.4 V (11 V to 16 V allowance)
Grounding System:
Negative ground
Allowable Operating Temperature:
0°C to +40°C
Dimensions (W × H × D): Installation Size:
182 mm × 52 mm × 160 mm
(approx.)
Panel Size:
188 mm × 58 mm × 13 mm
Mass:
1.3 kg (excluding accessories)
Design and specifications are subject to change without notice.
Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
ENGLISH
EN18-25_KD-R412_003A_f.indd 25
25
10/15/09 4:13:01 PM