JVC TM-H1700G User's Manual

TM-H1700G
OPERATING INSTRUCTIONS
[ TM-H1700G/E / TM-H1700G/U ]
COLOR VIDEO MONITOR
INSTRUCTIONS
FRANÇAIS
TM-H1700G
DEUTSCH
ENGLISH
BEDIENUNGSANLEITUNG : FARB-VIDEO-MONITOR
MANUEL D’INSTRUCTIONS : MONITEUR VIDEO COULEUR
MANUALE DI ISTRUZIONI : MONITOR VIDEO A COLORI
INSTRUCCIONES : MONITOR DE VIDEO A COLOR
!"#$%&'(&)
ITALIANO
For Customer Use:
Enter below the Serial No. which is located on the rear of the cabinet.
Retain this information for future reference.
Pour l’usage du client:
Enter ci-dessous le numéro de série qui est situé sur l’arrière du coffret.
Conserver cette information pour une référence ultérieure.
Model No. :
Numéro de modèle :
TM-H1700G
ESPAÑOL
Serial No. :
Numéro de série :
PHASE
BRIGHT
VOLUME/SELECT
MENU
UNDER
SCAN
A
B
POWER
INPUT SELECT
CHROMA CONTRAST
TM-H1700G
LCT1092-001A-H
1101-Y-U-JMT
Jan. 2002 No. 51922
WARNINGS
To prevent fire or shock hazard, do not expose this
monitor to rain or moisture. Dangerous high voltages
are present inside the unit. Do not remove the back
cover of the cabinet. When servicing the monitor,
consult qualified service personnel. Never try to service
it yourself.
WARNING : THIS APPARATUS MUST
BE EARTHED.
Machine Noise Information Ordinance 3. GSGV,
January 18, 1991: The sound pressure level at the
operator position is equal or less than 70 dB(A)
according to ISO 7779.
Improper operations, in particular alternation of high
voltage or changing the type of tube may result in x-ray
emission of considerable dose. A unit altered in such a
way no longer meets the standards of certification, and
must therefore no longer be operated.
No.51922
This monitor is equipped with a 3-blade grounding-type
plug to satisfy FCC rule. If you are unable to insert the
plug into the outlet, contact your electrician.
FCC INFORMATION (U.S.A. only)
2
The power supply voltage rating of this product is AC 120 V (For U.S.A. and Canada only) and AC 230 V (For European countries
or United Kingdom), the power cord attached conforms to the following power supply voltage and countries. Use only the power
cord designated to ensure Safety and EMC regulations of each countries.
Power cord
CAUTION: Changes or modification not approved by
JVC could void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and
receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV
technician for help.
Notice (U.S.A. only)
This product utilizes both a Cathode Ray Tube (CRT) and
other components that contain lead. Disposal of these
materials may be regulated in your community due to
environmental considerations. For disposal or recycling
information please contact your local authorities, or the
Electronics Industries Alliance: <http://www.eiae.org.>
Power supply voltage : AC 120 V
Countries
: U.S.A. and Canada
AC 230 V
European countries
AC 230 V
United Kingdom
Warning:
● Do not use the same Power Cord for AC 120 V as for AC 230 V. Doing so may cause malfunction, electric shock
or fire.
Note for the United Kingdom power cord only
The plug on the United Kingdom power cord has a built-in fuse. When replacing the fuse, be sure to use only a correctly rated
approved type, re-fit the fuse cover.
(Consult your dealer or qualified service personnel.)
How to replace the fuse
Open the fuse compartment with the blade screw driver, and
replace the fuse.
(* An example is shown in the illustration.)
Fuse
SCREEN BURN
● It is not recommended to keep a certain still image displayed on screen for a long time as well as displaying extremely bright
images on screen. This may cause a burning (sticking) phenomenon on the screen of cathode-ray tube. This problem does
not occur as far as displaying normal video playback motion images.
CONTENTS
SAFETY PRECAUTIONS ................................................................................. 2
PRECAUTIONS
● Use only the power source specified on the unit.
(120 V AC/230 V AC, 50 Hz/60Hz)
● When not using this unit for a long period of time, or when
cleaning it, be sure to disconnect the power plug from the
AC outlet.
● Do not allow anything to rest on the power cord. And do not
place this unit where people will tread on the cord. Do not
overload wall outlets or power cords as this can result in a
fire or electric shock.
● Avoid using this unit under the following conditions:
– in extremely hot, cold or humid places,
– in dusty places,
– near appliances generating strong magnetic fields,
– in places subject to direct sunlight,
– in badly ventilated places,
– in automobiles with doors closed.
● Do not cover the ventilation slots while in operation as this
could obstruct the required ventilation flow.
● When dust accumulates on the screen surface, clean it with
a soft cloth.
POWER CONNECTION
ENGLISH
In order to prevent any fatal accidents caused by misoperation
or mishandling the monitor, be fully aware of all the following
precautions.
TM-H1700G
1-2
SAFETY PRECAUTIONS
● Unplug this unit from the AC outlet and refer servicing to
qualified service personnel under the following conditions:
– when the power cord is frayed or the plug is damaged,
– if liquid has been spilled into the unit,
– if the unit has been dropped or the cabinet has been
damaged,
– when the unit exhibits a distinct change in performance.
● Do not attempt to service this unit yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Always refer servicing to qualified service
personnel.
● When replacement parts are required, have the service
personnel verify in writing that the replacement parts he/
she uses have the same safety characteristics as the
original parts. Use of manufacture’s specified replacement
parts can prevent fire, shock, or other hazards.
● Upon completion of any servicing or repair work to this unit,
please ask the service personnel to perform the safety
check described in the manufacturer’s service literature.
● When this unit reaches the end of its useful life, improper
disposal could result in a picture tube implosion. Ask
qualified service personnel to dispose of this unit.
CONTROLS AND FEATURES .......................................................................... 4
HOW TO HANDLE BASIC OPERATIONS ....................................................... 7
HOW TO USE THE MENU FUNCTIONS.......................................................... 9
HOW TO INITIALIZE THE SETTING .............................................................. 12
BASIC CONNECTION EXAMPLE.................................................................. 13
HOW TO USE EXTERNAL CONTROL .......................................................... 15
TROUBLESHOOTING .................................................................................... 16
SPECIFICATIONS .......................................................................................... 17
3
CONTROLS AND FEATURES
FRONT VIEW
REAR VIEW
<Front Panel>
<Rear Panel>
VIDEO A
12
REMOTE
10
0C
CHROMA CONTRAST
VOLUME/SELECT
MENU
UNDER
SCAN
A
IN
POWER
B
OUT
VIDEO B
PHASE
BRIGHT
INPUT SELECT
11
13
IN
OUT
VIDEO A
IN
OUT
VIDEO B
CHROMA CONTRAST
TM-H1700G
PHASE
BRIGHT
VOLUME/SELECT
MENU
UNDER
SCAN
A
B
POWER
INPUT SELECT
1
2
3
4
6
5
7
8
IN
9
IN
14
IN
Y/C
OUT
Y/C
OUT
AUDIO A
IN
OUT
AUDIO B
IN
Press this button to activate the picture color density
adjustment mode or picture hue adjustment mode. Each
time you press the button, the adjustment item changes.
Picture color density f Picture hue
No.51922
Adjust the value with the VOLUME/SELECT buttons 3.
Also used as a control button in the menu function mode.
2 Contrast/Brightness button
[CONTRAST / BRIGHT
]
Press this button to activate the picture contrast adjustment mode or picture brightness adjustment mode. Each
time you press the button, the adjustment item changes.
Picture contrast f Picture brightness
Adjust the value with the VOLUME/SELECT buttons 3.
Also used as a control button in the menu function mode.
3 Volume/Select buttons
+]
[VOLUME/SELECT –
Adjusts the speaker volume. Also used as a control
button in the menu function mode.
4 Menu button [MENU]
Displays and disappears the <MENU> screen.
Pressing the CHROMA/PHASE button 1 with the Menu
button depressed will display the <SET-UP MENU>
screen.
5 Under Scan button [UNDER SCAN]
Reduces the screen size to display the entire image.
Press the button again to cancel Under Scan.
When selected, the Under Scan button lights.
6 Input A (VIDEO) button [INPUT SELECT A]
Selects the video and audio signals input to the VIDEO A
@ and AUDIO A % terminals on the rear panel. The
button lights when selected.
15
7 Input B (VIDEO Y/C) button [INPUT SELECT B]
16
AUDIO A
IN
IN
OUT
11 REMOTE (external control) terminal
Note:
8 Power indicator
Connect this terminal to an external control unit to enable
remote operation of the monitor.
Refer to the HOW TO USE EXTERNAL CONTROL on
page 15 for more details.
12 Video A terminals [VIDEO A IN/OUT]
Unlit
: The main power is OFF.
Orange : The main power is ON, but the monitor’s power
is OFF (in the stand-by mode).
Green : The main power is ON, and the monitor’s power
is ON (in the normal operation mode).
9 Power switch [POWER
OUT
AUDIO B
Selects the video and audio signals input to the VIDEO B
# or VIDEO B (Y/C) $ and AUDIO B ^ terminals on
the rear panel. The button lights when selected.
● The VIDEO B terminals include a video terminal (BNC
connector) and a Y/C terminal (mini-DIN 4-pin connector). The Y/C (S-video) terminal has priority.
]
Press the power switch to turn the monitor’s power ON or
OFF when the main power is ON.
Note:
● When RUSH DELAY is set to SLOW, it takes about
three seconds before power is actually supplied after
the power switch is pressed.
10 Speaker
A built-in speaker is located inside the right side panel
when the monitor is viewed from the front.
Video signal input (IN) and output (OUT) terminals.
The output terminal is bridge-connected.
IN
: Video signal input terminal
OUT : Bridge-connected video signal output terminal
Notes:
* For corresponding audio signals, use the AUDIO A
terminals %.
* Also refer to BASIC CONNECTION EXAMPLE
on page 13.
13 Video B terminals [VIDEO B IN/OUT]
Video signal input (IN) and output (OUT) terminals.
The output terminal is bridge-connected.
IN
: Video signal input terminal
OUT : Bridge-connected video signal output terminal
Notes:
* For corresponding audio signals, use the AUDIO B
terminals ^.
* Also refer to BASIC CONNECTION EXAMPLE on
page 13.
14 Video B (Y/C) terminals [VIDEO B Y/C IN/OUT]
Y/C (S-video) signal input (IN) and output (OUT) terminals. The output terminal is bridge-connected.
IN
: Y/C-separated (S-video) video signal input
terminal
OUT : Bridge-connected Y/C-separated (S-video) signal
output terminal.
Notes:
* For corresponding audio signals, use the AUDIO B
terminals ^.
* When both VIDEO B terminals are connected (input) at
the same time, the Y/C terminal has priority.
* Also refer to BASIC CONNECTION EXAMPLE
on page 14.
15 Audio A terminals [AUDIO A IN/OUT]
Input (IN) and output (OUT) terminals for the audio signal
corresponding to the VIDEO A terminals @.
The output terminal is bridge-connected.
IN
: Audio signal input terminal
OUT : Bridge-connected audio signal output terminal
Notes:
* For corresponding video signals, use the VIDEO A
terminal @.
* Also refer to BASIC CONNECTION EXAMPLE
on page 13.
16 Audio B terminals [AUDIO B IN/OUT]
Input (IN) and output (OUT) terminals for the audio
signals corresponding to the VIDEO B terminals #
VIDEO B (Y/C) $.
The output terminal is bridge-connected.
IN
: Audio signal input terminal
OUT : Bridge-connected audio signal output terminal
Notes:
* For corresponding video signals, use the VIDEO B
terminals # or VIDEO B (Y/C) terminals $.
* Also refer to BASIC CONNECTION EXAMPLE
on pages 13 and 14.
5
1-3
TM-H1700G
4
OUT
OUT
ENGLISH
1 Chroma/Phase button
PHASE]
[ CHROMA/
(cont’d)
REAR VIEW
HOW TO HANDLE BASIC
OPERATIONS
BASIC OPERATION
<Rear Panel>
19
1. Press the MAIN POWER switch to turn on the
power.
2. Press the POWER switch to turn on the power.
REMOTE
For U.S.A. and Canada
POWER
VIDEO A
To AC outlet
(230 V AC,
50 Hz/60 Hz)
IN
OUT
VIDEO B
IN
19
IN
OUT
Y/C
About the STATUS indication
OUT
IN
3. Press the INPUT SELECT buttons to choose input.
OUT
AUDIO B
IN
OUT
Select video/audio signals input to terminals on the rear
panel. The selected button lights in green.
A
19
B
INPUT SELECT
18
For the United Kingdom
PAL
ON : Power turns ON. (Power indicator: lit)
Green: The main power is ON, and the monitor’s
power is ON (in the normal operation mode).
OFF : Power turns OFF. (Power indicator: unlit)
Orange : The main power is ON, but the monitor’s
power is OFF (in the standby mode)
Unlit
: The main power is OFF.
AUDIO A
For Europe
STATUS indication
(PAL or NTSC)
17
INPUT
SELECT
buttons
1 Input A
(VIDEO)
2 Input B
(VIDEO Y/C)
Terminals on the rear panel
Video signal input
VIDEO A terminal
VIDEO B terminal
Audio signal input
AUDIO A terminal
AUDIO B terminal
VIDEO B (Y/C) terminal
● With the COLOR SYSTEM setting set
to AUTO mode, when you turn on the
power or select inputs, the color
system indication appears for about
3 seconds on the screen while PAL or
NTSC signals are being detected.
It does not appear when receiving a
B/W signal or when no signal is input.
Refer to page 9 for more information
about COLOR SYSTEM setting and
page 10 for more information about
STATUS indication setting.
Note:The Y/C (S-video) terminal has priority.
17 Main power switch
No.51922
Press the switch to turn the main power ON or OFF. When
the main power is ON, the power lamp on the front panel
lights in orange and the monitor enters the stand-by
mode.
I : ON : OFF
18 AC inlet [AC IN]
Power input connector. Connect the provided AC power
cord ( to an AC outlet (120 V AC or 230 V AC,
50 Hz/60 Hz).
19 Power cord
Connects the provided power cord (120 V AC or
230 V AC, 50 Hz/60 Hz) to the AC IN connector *.
Caution:
In North America (USA and Canada), this monitor comes
with one power cable. In Europe and the United Kingdom, two power cables are provided (one for use in
continental European countries and the other for the UK).
Be sure to use the power cable that is appropriate for the
AC outlets used in your region. If none of the power
cables provided is suitable, please contact your dealer or
qualified service personnel to obtain the correct type of
power cable.
VOLUME/SELECT
Press this button to display the speaker volume level on the
screen.
+ : The Built-in speaker volume is increased. (00 = 50)
– : The Built-in speaker volume is decreased. (50 = 00)
VOLUME
:
20
* Screen indication will disappear about 10 seconds after operating.
* The on-screen display goes off when you press MENU button.
–
PICTURE ADJUSTMENT
PHASE
BRIGHT
The item you select is displayed on the screen.
1 Chroma control : Press the CHROMA/PHASE button once.
2 Phase control
: Press the CHROMA/PHASE button twice.
3 Contrast control : Press the CONTRAST/BRIGHT button once.
4 Brightness control : Press the CONTRAST/BRIGHT button twice.
* Pressing the CHROMA/PHASE button and CONTRAST/BRIGHT button
alternately while the item is shown on screen restores the previous status.
When no item is shown on screen, CHROMA and CONTRAST have priority.
2. Adjust with the VOLUME/SELECT buttons.
VOLUME/SELECT
Items
CHROMA
(Chroma)
PHASE
(Phase)
CONTRAST
(Contrast)
BRIGHT
(Brightness)
+
UPPER
1. Press select buttons corresponding to the item
you want to adjust.
CHROMA CONTRAST
VOLUME/SELECT button
–
+
lighter
deeper
reddish
greenish
lower
higher
darker
brighter
* Screen indication will disappear about 10 seconds after operating.
* The on-screen display goes off when you press MENU button.
6
00 ~ 50
4. Press the VOLUME/SELECT buttons to adjust the
speaker volume.
ENGLISH
To AC outlet
(120 V AC,
50 Hz/60 Hz)
TM-H1700G
1-4
CONTROLS AND FEATURES
–40 ~ +40
PHASE
:
00
PHASE
:
00
–
Notes:
+
LOWER
● Phase control is effective only in the
NTSC color system mode.
● Chroma control is not effective when
receiving B/W or when no signal is
input.
● When CHROMA is adjusted to “–40,”
the picture becomes less colorful.
● “NO EFFECT” is displayed (for about
3 seconds) when your selected
function has no effect.
● To change the display position on
screen, set UPPER or LOWER with
ADJ. BAR POSI.
7
HOW TO HANDLE BASIC
OPERATIONS (cont’d)
VIDEO SIGNAL CONTROLS
HOW TO USE THE MENU FUNCTIONS
DISPLAY AND SELECTION IN THE <MENU>
SCREEN MODE (SETTING)
<MENU> screen
UNDER SCAN
Press the UNDER SCAN button to reduce the size of display area
so that the whole picture is displayed on screen. Use to check the
picture frame.
You can set the following menu items.
Set them depending on your needs.
• SHARPNESS
• ADJ. BAR POSI.
• COLOR TEMP.
1
• COLOR SYSTEM
• RUSH DELAY
• ASPECT RATIO
PHASE
BRIGHT
SHARPNESS
No.51922
ADJ. BAR POSI.
COLOR TEMP.
COLOR SYSTEM
Function
displayed
PHASE
CHROMA/
PHASE
Forward selection mark (4)
CONTRAST/
BRIGHT
Reverse selection mark (4)
select.
3 Setting display: Indicates the current
settings (value).
4 Function display: The functions of
the front panel buttons (5 buttons on
the left) correspond to the function
displayed.
Function
displayed
Front panel
button
VOLUME/
SELECT (+)
VOLUME/
SELECT (–)
Function
displayed
+
Reverse the menu item.
–
Lower the adjustment
value. (to the minimum)
+
Raise the adjustment
value. (to the maximum)
4
Forward the setting value.
Increase (to max. value)
–
Forward the setting value
Decrease (to min. value)
1
Reverse the setting value
Purpose
Setting range
SHARPNESS
Picture sharpness
00
ADJ.BAR POSI
Volume bar position
LOWER
+01
COLOR TEMP.
Color temperature of white
balance
6500
9300
COLOR SYSTEM
Color system
AUTO
NTSC
RUSH DELAY
Delay value
STD.
ASPECT RATIO
Aspect ratio
4-3
••••••••••••
+39
+40
UPPER
Contents
Forward the menu item.
Contents
4
1
Reverse the setting value.
EXIT
Exits the <MENU> screen.
● When the screen aspect ratio is set to
16 - 9 (16:9) in ASPECT RATIO, the
picture will be vertically reduced.
PAL
SLOW
BRIGHT
:
BRIGHT
:
LOWER
PHASE
VOLUME/SELECT
MENU
BRIGHT
<Front panel buttons>
Contents
Quit (or Release) the <MENU>
screen
The upper screen; when setting
“UPPER” in “ADJ. BAR POSI.”
The lower screen; when setting
“LOWER” in “ADJ. BAR POSI.”
9
1-5
TM-H1700G
8
EXIT
00
EXIT
CHROMA CONTRAST
5. Press the MENU button to quit.
MENU
00
16-9
4. If you want to set the other menu items, repeat
procedures 2 and 3.
Function
displayed
UPPER
<ADJ. BAR POSI> screen
AUTO
* For normal use, leave the COLOR SYSTEM setting to AUTO.
If reception is unsatisfactory in AUTO position, set it to the appropriate color system mode (NTSC or PAL).
* When REMOTE SYSTEM is set to MAKE, and REMOTE ENABLE signal is short circuited (ON), "REMOTE"
is displayed on the ASPECT RATIO setting menu, and Aspect ratio cannot be operated from the front panel.
Front panel
button
MENU
2 Menu item: Menu items you can
3. Press the VOLUME/SELECT buttons to set.
MENU
VOLUME/SELECT
BRIGHT
menu item you select.
Contents
RUSH DELAY
Menu items
CHROMA CONTRAST
1 Selection mark (4): Indicates the
ASPECT RATIO
VOLUME/SELECT
4
EXIT
<Front panel buttons>
A selection mark (4) is put next to the selected item.
Front panel
button
00
LOWER
6500
AUTO
STD
4-3
3
The <MENU> screen is displayed.
* The on-screen display goes off automatically after about five
minutes with operation performed.
2. Press the CHROMA/PHASE or CONTRAST/BRIGHT
button to select MENU items.
CHROMA CONTRAST
:
:
:
:
:
:
2
1. Press the MENU button.
MENU
< MENU >
‰ SHARPNESS
ADJ. BAR POSI.
COLOR TEMP.
COLOR SYSTEM
RUSH DELAY
ASPECT RATIO
ENGLISH
Use these buttons for video signal control.
TM-H1700G
1-6
HOW TO USE THE MENU
FUNCTIONS (cont’d)
• WHITE BALANCE
• CONTROL LOCK
• STATUS DISPLAY
• REMOTE SYSTEM
• INPUT REMOTE
1
Notes:
● Parameters for H. POSITION and V. POSITION can be set separately depending on
the signal (Input A (VIDEO), Input B (VIDEO) or Input B (Y/C)) selected with the input
2
select buttons on the front panel.
Select the required video input with the input select buttons on the front panel in
advance.
● WHITE BALANCE can be set independently at 6500 or 9300 for the color temperature
value.
Set COLOR TEMP. to 6500 or 9300 on the <MENU> screen beforehand.
● INPUT REMOTE is shown when REMOTE SYSTEM is set to MAKE.
<SET-UP MENU>
‰ PICTURE SUB ADJ.
H. POSITION
V. POSITION
WHITE BALANCE
CONTROL LOCK
STATUS DISPLAY
REMOTE SYSTEM
INPUT REMOTE
CHROMA
MENU
The <SET-UP MENU> screen is displayed.
PHASE
No.51922
2. Press the CHROMA/PHASE or CONTRAST/BRIGHT
button to select the desired menu item.
CHROMA CONTRAST
PHASE
BRIGHT
PICTURE SUB ADJ.
H. POSITION
V. POSITION
A selection mark (4) is put next to the selected item.
Front panel
button
Function
displayed
Contents
CHROMA/
PHASE
Forward selection mark (4)
CONTRAST/
BRIGHT
Reverse selection mark (4)
CONTROL LOCK
CHROMA CONTRAST
3. Press the VOLUME/SELECT buttons to set.
Front panel
button
VOLUME/
SELECT (+)
VOLUME/
SELECT (–)
Function
displayed
+
4
CUTO
–
1
DRV
Forward the setting value
Selects CUT OFF setting screen
Decrease (to min. value)
Reverse the setting value
Selects DRIVE setting screen
Notes:
● For WHITE BALANCE items, select the CUT OFF or DRIVE
setting screen, then select the function display for adjustment.
● Press the EXIT (MENU) button to return to the <SET-UP
MENU> screen.
10
3
4
VOLUME/SELECT
MENU
1 Selection mark (4): Indicates the
menu item you select.
2 Menu item: Menu items you can
select.
3 Setting display: Indicates the
current settings (value).
4 Function display: The functions of
the front panel buttons (5 buttons
on the left) correspond to the
function displayed.
V. POSITION
DRIVE
R. DRIVE
B. DRIVE
CUT OFF R. CUT OFF
G. CUT OFF
B. CUT OFF
CONTROL LOCK
STATUS DISPLAY
REMOTE SYSTEM
INPUT REMOTE
Settings
Selects CONTRAST/BRIGHT/CHROMA/PHASE. The
selected setting screen is shown. Select the function display for
adjustment.
Adjusts contrast.
Adjusts brightness.
Adjusts color density.
*1
Adjusts hue.
*1
Adjusts the horizontal position of the
screen (+: Horizontal position shifts
to the right/-: Horizontal position shifts to
the left)
Adjusts the vertical position of the screen
(+: Vertical position moves up/-: Vertical
position moves down)
Adjusts the white balance.
Adjusts red level.
Adjusts blue level.
Adjusts red cut off.
Adjusts green cut off.
Adjusts blue cut off.
Sets the operation buttons on the front
panel to control lock mode.
Sets the status display of the color system.
Sets the external control function method.
Sets external control of input selection.
(Shown only when REMOTE SYSTEM is
set to MAKE.)
–10
–9 • •
–01
00
+01 • •
+09
– 10
– 10
– 01
– 01
00
+09
+10
00
+10
–01
00
+01 • •
+01 • •
+01 • •
+09
–10
–9 • •
–9 • •
–9 • •
+10
+09
+10
–5
•••
– 01
00
+1
•••
+5
–5
•••
–01
00
+1
•••
+5
Selects the drive (DRV) or cut off (CUTO) adjustment. The selected
setting screen is shown. Select the function display for adjustment.
–20
– 20
–19 • • –01 00
– 1 9 • • – 01 00
– 1 9 • • – 01 00
–20
–20
–19 • •
–19 • •
OFF
ON
OFF
ON
– 20
MAKE
A–B
–01
–01
00
00
+01 • • +19
+01 • • +19
+20
+01 • •
+01 • •
+19
+20
+19
+19
+20
+20
+01 • •
TRG.
+20
*2
*2
A/B
*1 May not be shown depending on the type of signals input.
*2 Refer to HOW TO USE EXTERNAL CONTROL on page 15 for more details.
Notes:
Function
displayed
Contents
Forward the menu item.
Reverse the menu item.
–
Lower the adjustment
value. (to the minimum)
+
Raise the adjustment
value. (to the maximum)
4
Forward the setting value.
1
Reverse the setting value.
EXIT
Exit the <MENU>
screen.
DRV
Selects DRIVE adjustment.
Contents
Increase (to max. value)
H. POSITION
<Front panel buttons>
CUTO
VOLUME/SELECT
OFF
ON
MAKE
A–B
BRIGHT
REMOTE SYSTEM
INPUT REMOTE
:
:
:
:
WHITE BALANCE
WHITE BALANCE
STATUS DISPLAY
00
00
EXIT
PHASE
1. While pressing the MENU button, press the
CHROMA/PHASE button.
:
:
Purpose
Image sub adjustment
CONTRAST
BRIGHT
CHROMA
PHASE
<SET-UP MENU> screen
You can set the following set-up menu items.
• PICTURE SUB ADJ.
• H. POSITION
• V. POSITION
Set-up menu items
PICTURE SUB ADJ.
ENGLISH
DISPLAY AND SELECTIONS IN THE <SET-UP
MENU> MODE (SETTING)
RB
Selects CUT OFF
adjustment.
Adjusts red and blue
signal level.
RGB
Adjusts red, green and
blue signal level.
DISP
Turns the ON-SCREEN
display on or off. (This
function is effective only
in the DRIVE or CUT OFF
adjustment mode.)
4. To set the other set-up menu items, repeat the
procedures 2 and 3.
5. Press the MENU button to quit.
MENU
Front panel
button
MENU
Function
displayed
EXIT
Contents
Quit (or Release) the <MENU>
screen
Note:
Setting
Description
MAKE
Make contact system: Controls the function with H and L (shortcircuits or opens 15th terminal (GND)).
TRG.
Trigger system: Controls the function by short-circuiting (shortcircuits or opens 15th terminal (GND)) with pulse (about 1 sec.)
A-B
Switches the input by short-circuiting a specified signal line in
INPUT A or B.
A/B
Switches between INPUT A and INPUT B with D-sub pin 2.
(Also, refer to HOW TO USE EXTERNAL CONTROL on page 15.)
● When the CONTROL LOCK function is
set to ON, pressing operation buttons
on the front panel will display the
message “CONTROL LOCK ON!” on
the screen for about 3 seconds.
● The CONTROL LOCK function is
maintained even when the power is
turned off.
● To turn off the CONTROL LOCK
function, while holding the MENU button
press the CHROMA/PHASE button.
Then set the CONTROL LOCK function
to OFF.
● Even when the CONTROL LOCK
function is set to ON, the following
operations are available:
– Power Switch operation
– Volume control with the VOLUME/
SELECT buttons
– Display or disappear of the <SET-UP
MENU> screen.
● The STATUS DISPLAY function can be
set to display (ON) or not display (OFF)
the present color system when the
power is turned on or the input signal is
changed. Refer to page 7 for more
information.
● When REMOTE SYSTEM is set to
MAKE and any one of the INPUT A and
B buttons or the UNDER SCAN button
is pressed, “REMOTE ON!” appears on
screen for about 3 seconds. (Not
shown with CONTROL LOCK set to
ON.)
● When REMOTE SYSTEM is set to
TRG, the front panel controls can be
operated.
● INPUT REMOTE and REMOTE
SYSTEM are enabled when REMOTE
ENABLE is set to ON.
11
BASIC CONNECTION EXAMPLE
HOW TO INITIALIZE THE
SETTING
Notes:
SCREEN DISPLAY AND SELECTIONS IN THE
<SET-UP MENU> RESET MODE
• Before connecting your system, make sure that all units are turned off.
• The illustration below shows some examples of different connections. Terminal connections may differ depending on the component connected.
Be sure to refer to the instructions provided with the unit(s) you are connecting.
• Each pair of input (IN) and output (OUT) terminals are bridge-connected.
• If you’re not connecting any equipment to a bridged output (OUT) terminal, be sure not to connect any other cables to the bridged output (OUT)
terminal as this will cause the terminating resistance switch to open (auto terminate function).
• When making a bridge connection, connect the input (IN) and output (OUT) terminals on the monitor to separate video components.
You can set <MENU> and <SET-UP MENU> screen items, picture adjustment items and
the volume level to their factory-set (initial) values.
<SET-UP MENU> RESET screen
<SET–UP MENU> RESET
Are you
“Yes” then
“No”
then
1. Press the Power ( ) switch to turn the power
OFF (activate the standby mode).
sure ?
<+>
<MENU>
(For example, if both terminals are connected to the same VCR, resonance may occur except during playback. This is caused by the same video
signal “looping” between the VCRs, and is not a malfunction.)
• Select the video input signal (INPUT A(VIDEO) or INPUT B (VIDEO/Y/C)) with the INPUT SELECT buttons on the front panel. When both
VIDEO B terminals are connected (input) at the same time, the Y/C terminal has priority.
VIDEO A Connection Example (Select Input A (VIDEO))
POWER
VIDEO A
Video
Video
3. Setting
Initialization is required.
VOLUME/SELECT
Press the VOLUME/SELECT [+] button.
* Initialization is completed, and the <SET-UP MENU>
RESET screen disappears.
Sorts
PICTURE SUB ADJ.
CONTRAST
BRIGHT
CHROMA
PHASE
H. POSITION
V. POSITION
WHITE BALANCE
R. CUT OFF
G. CUT OFF
B. CUT OFF
R. DRIVE
B. DRIVE
CONTROL LOCK
STATUS DISPLAY
REMOTE SYSTEM
INPUT REMOTE
00
00
00
00
00
OFF
ON
MAKE
A–B
CHROMA
PHASE
CONTRAST
BRIGHT
00
00
00
00
VOLUME
Initialization is not required.
MENU
00
LOWER
6500
AUTO
STD
4–3
(Video signal cable)
IN
OUT
VCR
Audio
Video Monitor
(Audio signal cable)
IN
Y/C
OUT
AUDIO A
00
00
00
00
00
00
Audio
VCR
IN
OUT
AUDIO B
VIDEO B (VIDEO) Connection
Example (Select Input B (VIDEO))
Video Camera
IN
(Audio signal cable)
Video Monitor
Audio
OUT
(Audio signal
cable)
Video
VCR
(Video signal cable)
Video Monitor
Audio
(Audio signal cable)
Video Monitor
: Signal Flow
VCR
20
13
1-7
TM-H1700G
12
Press the MENU button.
* Initialization is aborted, and the <SET-UP MENU>
RESET screen disappears.
Video
Initialization
(setting)
SHARPNESS
ADJ. BAR POSI
COLOR TEMP
COLOR SYSTEM
RUSH DELAY
ASPECT RATIO
● The <SET-UP MENU> RESET screen will not be
displayed if the MENU or CHROMA/PHASE buttons are
pressed for a very short time. Keep pressing them until
the display screen appears.
OUT
ENGLISH
Note:
PHASE
Functions (Items)
<MENU> screen
POWER
IN
VIDEO B
<SET-UP MENU> screen
MENU
Initial settings
Picture adjustment
CHROMA
The <SET-UP MENU> RESET screen is displayed.
* The screen automatically disappears when no operation
is performed after about 5 minutes.
(Video signal cable)
(Video signal cable)
Video Camera
Volume
No.51922
2. While pressing both MENU button and CHROMA/
PHASE button, press the Power ( ) switch to turn
the power ON.
TM-H1700G
1-8
HOW TO USE EXTERNAL
CONTROL
BASIC CONNECTION EXAMPLE
(cont’d)
ABOUT EXTERNAL CONTROL
VIDEO B (Y/C) Connection Example (Select Input B (Y/C))
This monitor is provided with an external control terminal. MAKE (make contact) or TRIG. (trigger) system can be selected.
(MAKE (make contact system): The function is controlled with H and L (short-circuit/open with the 15th pin GND).
(TRIG. (trigger system): The function is controlled by short-circuiting with pulses (for about 1 second) (short-circuit/open with the
15th pin GND).
VIDEO A
* The 14th pin (REMOTE ENABLE) is controlled with MAKE even though TRIG. is selected.
OUT
Note:
● When this monitor is externally controlled, the following buttons are disabled.
MAKE: INPUT-A and B, UNDER SCAN on the front panel.
IN
OUT
Y/C (S-video)
(Y/C (S-video) signal cable)
VCR
IN
Video Monitor
Y/C (S-video)
Audio
(Audio signal cable)
OUT
AUDIO B
IN
9
5
4 8
3 7
2 6
1
The Names and Functions of Terminals
AUDIO A
IN
15
14
13
12
11
(Y/C (S-video) signal cable)
OUT
VCR
10
Connections
Connect (short-circuit) the 15th terminal (GND) to each of the 1st through 14th terminals in the
3-lines 15-pins D-sub connector. The functions of each terminal are listed below.
Y/C
Video Monitor
Audio
OUT
(Audio signal cable)
: Signal Flow
No.51922
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Names
not used
INPUT A
INPUT B
not used
not used
not used
not used
not used
not used
ASPECT
UNDER SCAN
not used
not used
REMOTE ENABLE
15
GND
Functions
–
Changes the input to INPUT A
Changes the input to INPUT B
–
–
–
–
–
–
Changes the screen ratio to 16:9
Makes the screen under-scan
–
–
Makes the external control from the
REMOTE terminal valid or invalid
Used as a ground terminal
Operations (OFF p[ ON)
–
–
Not change
Change
Not change
Change
–
–
–
–
–
–
–
–
–
–
–
–
4:3
16:9
Over-scan
Under-scan
–
–
–
–
Invalid
Valid
–
*1
*2
*4
*4
*2
*2
*2
*2
*2
*2
ENGLISH
IN
VIDEO B
Video Camera
*2
*2
*3
–
*1 : OFF stands for disconnection, and ON stands for short-circuit.
*2 : Do not connect.
*3 : Setting REMOTE ENABLE to ON enables remote control from the REMOTE terminal.
*4 : INPUT REMOTE setting in the set-up menu (REMOTE SYSTEM shown only when MAKE is selected.)
For the D-sub pins 2 and 3, 2-pin or 1-pin control can be set with INPUT REMOTE in the set-up menu.
• 2-pin control: Only the specified signal line in INPUT-A or B is short-circuited.
• 1-pin control: Switches between INPUT-A and INPUT-B only with the 2nd pin of the D-sub connector.
Open (H): INPUT-A
Short-circuit (L): INPUT-B
NOTE : When more than two terminals are selected (short-circuited) from INPUT A and INPUT B, the signal input is prioritized
alphabetically (A, B).
To control INPUT A and INPUT B, we recommend using the interlock switch, which turns off a switch when another switch
is turned on.
14
15
TROUBLESHOOTING
Solutions to common problems related to your monitor are described here. If none of the solutions presented here
solves the problem, unplug the monitor and consult a JVC-authorized dealer or service center for assistance.
Problems
No power supply.
Points to be checked
Measures (Remedy)
Is the power plug loosened or disconnected?
Firmly insert the power plug.
Is the main power turned OFF?
Turn the main power ON. (See page 6.)
Is the video signal output from the connected
component?
Set the connected component correctly.
Is the input signal selected properly?
Select the required video signal input with the
Input select button. (See page 7.)
Is the video cable disconnected?
Connect the video signal cable firmly.
(See pages 13 and 14.)
Is the audio signal output from the connected
component?
Set the connected component correctly.
Is the volume output set to minimum?
Adjust the speaker volume with the VOLUME/
SELECT button. (See page 7.)
Is the audio cable disconnected?
Connect the audio signal cable firmly.
(See pags 13 and 14.)
Shaking picture.
Is the monitor close to a device generating a
strong magnetic field?
Move the device away from the monitor until the
picture stabilizes.
No colors, wrong
color, or dark picture.
Is the color system selected properly?
Set COLOR SYSTEM in the <MENU> screen to
AUTO. (See page 9.)
Has the picture control setting (CONTRAST,
BRIGHT, CHROMA or PHASE) been changed?
Set each picture control to the standard setting.
(See page 7.)
Unnatural, irregularly
colored, or distorted
picture.
Is the monitor close to a speaker, magnet or any
other device generating a strong magnetic field?
Move the device away from the monitor and turn
the monitor’s power off. Wait at least 30 minutes,
then turn the power on again.
Dark stripes appear
at the top and bottom
of the screen, picture
vertically squeezed.
Is the aspect ratio set to 16:9?
Set ASPECT RATIO in the <MENU> screen to
[4 : 3 (4 – 3)]. (See page 9.)
When controlling externally, ASPECT RATIO
should be set to [4 : 3 (4 – 3)]. (See page 15.)
The overall picture
size is too small.
Has the UNDER SCAN button been pressed so
the UNDER SCAN button lights?
Press the UNDER SCAN button to turn off the
button. (See page 4.)
Function buttons on
the front panel do not
function.
Has control of the buttons been locked? (Has
the CONTROL LOCK function been set to ON?)
Set CONTROL LOCK in the <SET-UP MENU>
screen to OFF. (See pages 10 and 11.)
The INPUT SELECT
buttons do not
function.
Is input selection under external control? (Has
the INPUT REMOTE function been set to valid
(A/B)?)
Set REMOTE SYSTEM in the <SET-UP MENU>
screen to TRG. (See pages 10 and 11.)
Set REMOTE ENABLE to OFF (invalid).
(See page 15.)
No picture with the
power on.
No sound.
No.51922
The following are not malfunctions:
● When a bright still image (such as a white cloth) is displayed for a long period, it may appear to be colored. This is due to the
structure of the cathode ray tube and will be deleted when another image is displayed.
● You experience a mild electric shock when you touch the picture tube. This phenomenon is due to a normal buildup of static
electricity on the CRT and is not harmful.
● The monitor emits a strange sound when the room temperature changes suddenly. This is only a problem if an abnormality
appears on the screen as well.
● If two or more monitors are operated next to each other, their images may shake or be distorted. This phenomenon is due to
mutual interference; it is not a malfunction. Move the monitors away from each other until the interference disappears or turn
the power off on any monitor that is not being used.
1-9
TM-H1700G
16
TM-H1700G
SPECIFICATIONS
Effective screen size
Scanning frequency
Horizontal resolution
Input terminals
VIDEO A
VIDEO B
AUDIO A
AUDIO B
REMOTE
: Color video monitor
: PAL, NTSC (3.58)
: 16-3/16" (41 cm) measured
diagonally,
90° deflection, in-line gun,
trio-dot type (phosphor dot-trio
pitch 0.27 mm)
: Width
12-7/8" (327.5 mm)
Height
9-5/8" (246.2 mm)
Diagonal
16-1/32" (407.1 mm)
: (H) 15.734 kHz (NTSC)
15.625 kHz (PAL)
(V) 59.94 Hz (NTSC)
50 Hz (PAL)
: 750 TV lines or more
Audio power output
Built-in speaker
Environmental
conditions
Power requirements
Power consumption
Dimensions
Weight
Accessory
: 1 W (monaural)
: 8 cm round x 1
impedance of 8 Ω
: Operation temperature:
0°C – 40°C (32°F – 104°F)
Operation humidity:
20 % – 80 % (non-condensing)
: 120 V/230 V AC, 50 Hz/ 60 Hz
: 1.1 A (120 V AC)/0.7 A (230 V
AC)
: Width
15-5/8" (395 mm)
Height
13-1/4" (334 mm)
Depth
16-1/2" (418.1 mm)
: 43.2 lbs (19.6 kg)
: AC power cord
: Composite video:
1 line, BNC connector x 2,
1 V(p-p), 75 Ω, negative sync
(bridge connection possible,
auto termination)
: Composite video:
1 line, BNC connector x 2,
1 V(p-p), 75 Ω, negative sync
(bridge connection possible,
auto termination)
Y/C-separated:
1 line, mini-DIN 4-pin
connector x 2
Y: 1.0 V (p-p), 75 Ω
C (BURST): 0.286 V (p-p),
75 Ω (NTSC)
0.3 V (p-p), 75 Ω (PAL)
(bridge connection possible,
auto termination)
: 1 line (monaural), RCA pin x 2
0.5 V(rms), high-impedance
(bridge connection possible)
: 1 line (monaural), RCA pin x 2
0.5 V(rms), high-impedance
(bridge connection possible)
: Point-of-contact connection,
1 line
D-sub connector (15-pin, 3-line)
ENGLISH
Type
Color system
Picture tube
* Illustrations used in this manual are for explanatory purposes only. The appearance of the actual product may differ slightly.
* Dimensions and weight are approximate.
* E. & O. E. Design and specifications subject to change without notice.
17
1-10
No.51922
TM-H1700G
Dimensions
Unit : inch (mm)
< Side View >
< Front View >
16-1/2 (418)
16-1/8 (407)
15-5/8 (395)
1/16
(1.5)
VOLUME/SELECT
MENU
UNDER
SCAN
A
BRIGHT
B
POWER
INPUT SELECT
11-3/8 (288)
2-3/4 (68)
11-3/8 (286)
1/8 (3)
PHASE
1/8 (3)
CHROMA CONTRAST
TM-H1700G
7 (175)
9-5/8 (246.2)*
13-1/4 (334)
12-7/8 (327.5)*
ø7/8 (20)
* Asterisks (*) are used to indicate front panel
dimensions.
Y/C (Mini DIN 4 pin) terminal
specification
2
4
Pin No.
IN
1
3
OUT 2
4
1
3
Y/C
Signal
1
GND (Y)
2
GND (C)
3
Y
4
C
18
No.51922
1-11
TM-H1700G
TM-H1700G COLOR VIDEO MONITOR
VICTOR COMPANY OF JAPAN, LIMITED
Printed in Thailand
LCT1092-001A-H
1101-Y-U-JMT
© 2001 VICTOR COMPANY OF JAPAN, LIMITED
1-12
No.51922
82 ,2!#