advertisement
VIDEO CASSETTE RECORDER
HR-VP70U
A B
POWER
ENTER
1
4
7
C.RESET
CANCEL
CH SKIP
2
5
DAILY (M–F)
8
AUX
0
OSD
3
6
WEEKLY
9
TIMER
TV
VOL.
CH
SP/EP
REW
DISPLAY TV/VCR
(VIDEO)
PLAY
CABLE DBS
TV VCR
FF
REC
C.M
EMOR
Y
ADD
MEN
U
STOP
PAUSE
SKIP SEAR
CH
OK
SHUTTLE
PLUS
MULTI BRAND
REMOTE CONTROL UNIT
POWER
VIDEO (MONO)L – AUDIO – R
MENU
SP
V C R
TIMER
AM
PM
H M S
ST
SAP
M
R E C
PLAY
PAUSE
CH
REW
2
PLAY
FF
2
OK
REC q
STOP/EJECT
5
/
8
PAUSE
6
INSTRUCTIONS
For Customer Use:
Enter below the Serial No. which is located on the rear of cabinet. Retain this information for future reference.
Model No. HR-VP70U
Serial No.
LPT0002-0E5A
2
EN
Dear Customer,
Thank you for purchasing the JVC VHS video cassette recorder. Before use, please read the safety information and precautions contained in the following pages to ensure safe use of your new VCR.
CAUTIONS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS
UNIT TO RAIN OR MOISTURE.
CAUTION:
This video cassette recorder should be used with AC
120V`, 60Hz only.
To prevent electric shocks and fire hazards, DO NOT use any other power source.
Failure to heed the following precautions may result in damage to the VCR, remote control or video cassette.
1. DO NOT place the VCR . . .
... in an environment prone to extreme temperatures or humidity.
... in direct sunlight.
... in a dusty environment.
... in an environment where strong magnetic fields are generated.
... on a surface that is unstable or subject to vibration.
2. DO NOT block the VCR’s ventilation openings.
3. DO NOT place heavy objects on the VCR or remote control.
4. DO NOT place anything which might spill on top of the
VCR or remote control.
5. AVOID violent shocks to the VCR during transport.
**MOISTURE CONDENSATION
Moisture in the air will condense on the VCR when you move it from a cold place to a warm place, or under extremely humid conditions—just as water droplets form on the surface of a glass filled with cold liquid. Moisture condensation on the head drum will cause damage to the tape. In conditions where condensation may occur, keep the VCR’s power turned on for a few hours to let the moisture dry before inserting a tape.
**ABOUT HEAD CLEANING
Accumulation of dirt and other particles on the video heads may cause the playback picture to become blurred or interrupted. Be sure to contact your nearest JVC dealer if such troubles occur.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION:
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE
LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQU'AU FOND.
Note to CATV system installer:
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
VCR Plus+C 3 and PlusCode are trademarks of Gemstar Development Corporation.
The VCR Plus+ system is manufactured under license from
Gemstar Development Corporation.
DSS TM is an official trademark of DIRECTV, Inc., a unit of GM
Hughes Electronics. PRIMESTAR is a registered service mark of
Primestar Partners, L.P. DISH Network TM
is a trademark of
Echostar Communications Corporation.
CAUTION:
Changes or modifications not approved by JVC could void user's authority to operate the equipment.
n Cassettes marked "VHS" (or "S-VHS") can be used with this video cassette recorder. However, only "VHS" recordings can be played back in this model.
n HQ VHS is compatible with existing VHS equipment.
IMPORTANT PRODUCT
SAFETY INSTRUCTIONS
Electrical energy can perform many useful functions. But improper use can result in potential electrical shock or fire hazards. This product has been engineered and manufactured to assure your personal safety. In order not to defeat the built-in safeguards, observe the following basic rules for its installation, use and servicing.
ATTENTION:
Follow and obey all warnings and instructions marked on your product and its operating instructions. For your safety, please read all the safety and operating instructions before you operate this product and keep this booklet for future reference.
EN
3
5. Ventilation
Slots and openings in the cabinet are provided for ventilation.
To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered.
• Do not block the openings by placing the product on a bed, sofa, rug or other similar surface.
• Do not place the product in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
6. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling only as recommended by the manufacturer.
INSTALLATION
1. Grounding or Polarization
(A) Your product may be equipped with a polarized alternatingcurrent line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way.
This is a safety feature.
If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
(B) Your product may be equipped with a 3-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature.
If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.
2. Power Sources
Operate your product only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. If your product is intended to operate from battery power, or other sources, refer to the operating instructions.
3. Overloading
Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.
4. Power Cord Protection
Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
ANTENNA INSTALLATION
INSTRUCTIONS
1. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code,
ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding connectors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
2. Lightning
For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.
3. Power Lines
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
ANTENNA
LEAD IN WIRE
GROUND CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION
810-20)
ELECTRIC SERVICE
EQUIPMENT
GROUNDING
CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING ELECTRODE SYSTEM
(NEC ART 250. PART H)
NEC – NATIONAL ELECTRICAL CODE
4
EN
USE
1. Accessories
To avoid personal injury:
• Do not place this product on an unstable cart, stand, tripod, bracket, or table. It may fall, causing serious injury to a child or adult, and serious damage to the product.
• Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the product.
• Use a mounting accessory recommended by the manufacturer and follow the manufacturer’s instructions for any mounting of the product.
• Do not try to roll a cart with small casters across thresholds or deep-pile carpets.
2. Product and Cart Combination
A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
PORTABLE CART WARNING
(Symbol provided by RETAC)
3. Water and Moisture
Do not use this product near water—for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool and the like.
4. Object and Liquid Entry
Never push objects of any kind into this product through openings as they may touch dangerous voltage points or shortout parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
5. Attachments
Do not use attachments not recommended by the manufacturer of this product as they may cause hazards.
6. Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
7. Heat
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
SERVICING
1. Servicing
If your product is not operating correctly or exhibits a marked change in performance and you are unable to restore normal operation by following the detailed procedure in its operating instructions, do not attempt to service it yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
2. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a.When the power supply cord or plug is damaged.
b.If liquid has been spilled, or objects have fallen into the product.
c.If the product has been exposed to rain or water.
d.If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.
e.If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in performance—this indicates a need for service.
3. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.
4. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in safe operating condition.
HOW TO USE THIS INSTRUCTION
MANUAL
● All major sections and subsections are listed in the Table Of
Contents on page 5. Use this when searching for information on a specific procedure or feature.
● The Index on pages 56–59 lists frequently-used terms, and the number of the page on which they are used or explained in the manual. This section also illustrates the controls and connections on the front and rear panel, the front display panel and the remote control.
● The
Z
mark signals a reference to another page for instructions or related information.
● Operation buttons necessary for the various procedures are clearly indicated through the use of illustrations at the beginning of each major section.
BEFORE YOU INSTALL YOUR NEW
VCR . . .
. . . please read the sections/literature listed below.
● ”Cautions” on page 2
● ”Important Products Safety Instructions” on the previous pages
CONTENTS
I
NSTALLING YOUR NEW VCR 6
Basic Connections ..................................6
I
NITIAL SETTINGS
Plug & Play .................................................. 7
Language ..................................................... 8
Clock ............................................................ 9
7
Preparation ................................................................9
Semi-Auto ................................................................10
Manual .................................................................... 11
Auto ........................................................................ 11
Tuner .......................................................... 12
Set Receivable Channels .......................................... 12
Add Or Delete A Channel ........................................ 14
Cable Box Control ....................................... 15
Situate And Connect Controller ............................... 15
Set Cable Box Output Channel ................................ 16
Set Cable Box Brand ................................................17
VCR Plus+ Setup ......................................... 18
DBS Receiver Control ................................... 20
Situate And Connect Controller ............................... 20
Set DBS Receiver Output Channel ........................... 21
Set DBS Receiver Brand ........................................... 22
S IMPLE PLAYBACK AND
RECORDING 23
Simple Playback ......................................... 23
Simple Recording ........................................ 24
P
LAYBACK AND RECORDING
FEATURES 25
Playback Features ...................................... 25
Still Picture/Frame-By-Frame Playback ..................... 25
Slow Motion/Reverse Slow Motion .......................... 25
Variable-Speed Search/Reverse Motion Playback ..... 25
High-Speed Search ..................................................25
Manual Tracking ......................................................26
Tape Position Indicator ............................................26
Video Stabilizer .......................................................27
Superimpose ............................................................28
Select The Soundtrack .............................................29
Index Search ............................................................30
Instant ReView .........................................................30
Skip Search ..............................................................30
Repeat Playback ......................................................31
Counter Reset ..........................................................31
Counter Memory .....................................................31
Next-Function Memory ............................................31
AV COMPU LINK Playback ..................................... 32
Auto Picture ................................................ 34
Preparation ..............................................................34
Playback ..................................................................35
Recording Features ..................................... 36
Record One Program While
Watching Another ....................................................36
Display Elapsed Recording Time .............................. 36
Stereo And SAP (Second Audio Program) ................. 37
To Record SAP Programs ..........................................37
EN
5
T
IMER RECORDING 38
VCR Plus+ Timer Programming .................... 38
On-Screen Timer Programming ...................40
Check And Cancel Programs ................................... 42
Auto Timer ...............................................................43
Instant Timer Recording (ITR) ....................... 44
E
DITING 45
Edit To Or From Another VCR ....................... 45
Edit From A Camcorder ............................... 46
S
PECIAL FEATURES 48
TV Multi-Brand Remote Control .............................. 48
Cable Box Multi-Brand Remote Control ................... 49
DBS Receiver Multi-Brand Remote Control .............. 50
Control Two JVC VCRs ............................................51
T
ROUBLESHOOTING 52
Power ........................................................ 52
Tape Transport ............................................ 52
Playback .................................................... 52
Recording ................................................... 52
Timer Recording .......................................... 53
Other Problems .......................................... 54
Q
UESTIONS AND ANSWERS 55
Playback .................................................... 55
Recording ................................................... 55
Timer Recording .......................................... 55
I
NDEX 56
List Of Terms ............................................... 56
Front View .................................................. 57
Rear View .................................................. 58
Front Display Panel ..................................... 58
Remote Control ........................................... 59
S
PECIFICATIONS 60
F
OR SERVICING (Only in U.S.A.) 61
W
ARRANTY (Only in U.S.A.) 62
6
EN
Basic
Connections
Antenna or Cable
Coaxial Cable
ANT. IN
(Antenna or Cable input)
Flat Feeder
AC Power
Cord
Back of VCR
AC
Outlet
Audio Cable
(not supplied)
Video Cable
(not supplied)
TV
Matching Transformer
(not supplied)
75 ohm terminal
RF OUT
RF Cable
(supplied)
Back of VCR
CH3 CH4
NOTES:
● The VCR channel is the channel on the TV which will display the audio and video signals from the VCR. The VCR's CH3-
CH4 switch, on the back of the VCR, sets the VCR channel to
CH3 or CH4.
● The CH3–CH4 switch is preset to the CH3 position.
Set to CH4 if CH3 is used for broadcasting in your area and set the channel on the TV to correspond to the VCR's CH3–
CH4 switch setting.
● If RF connection to TV is used, when switching from VCR to TV mode and from TV to VCR it may be necessary to issue a CH UP and then CH DOWN on TV to obtain a good quality picture.
● Even if you are using AV cables to connect your VCR to your
TV, you must also connect it using the RF cable. This will
( ensure that you can record one show while watching another
Z
pg. 36).
● For full identification of the VCR's rear panel, refer to the
Index (REAR VIEW
Z
pg. 58).
INSTALLING YOUR NEW VCR
1
CHECK CONTENTS
Make sure the package contains all of the accessories listed in “SPECIFICATIONS” (
Z
pg. 60).
SITUATE VCR
Place the VCR on a stable, horizontal surface.
2
3
4
5
CONNECT VCR TO TV
The connection method you use depends on the type of
TV you have.
RF Connection
● To Connect To A TV With NO AV Input Terminals . . .
a– Disconnect the TV antenna from the TV.
b– Connect the TV antenna cable to the ANT. IN jack on the rear of the VCR.
c– Connect the supplied RF cable between the RF
OUT jack on the rear of the VCR and the TV’s antenna terminal. Set TV on CH3 or CH4 corresponding to the CH3 – CH4 switch setting on the back of the VCR.
AV Connection
● To Connect To A TV With AV Input Terminals . . .
a– Connect the antenna, VCR and TV as shown in the illustration.
b– Connect an Audio/Video Cable between the AUDIO
OUT and VIDEO OUT jacks on the rear of the VCR and the AV IN jacks on the TV. Set your TV in video input mode or A/V input mode. Refer to the TV
Instruction Manual.
CONNECT VCR TO
POWER SOURCE
Connect the power plug to an AC outlet.
● The clock and tuner channels will automatically be set when the antenna is connected and when the AC is first connected to the VCR (
Z
pg. 7).
(If "Auto" or "CH" is displayed on the front display panel before the VCR is powered on, the clock and tuner channels are being set automatically. Wait for the time to be displayed on the front display panel before powering on the VCR.)
FINAL PREPARATION FOR
USE
Power on the VCR and select the VCR channel (3 or 4) by setting the switch on the rear of the VCR as shown in the illustration.
You can now perform simple playback ( simple recording (
Z
pg. 24).
Z
pg. 23) or
INITIAL SETTINGS
Plug & Play
Auto Clock Set/Auto Tuner Set
2 q 5
8
6
2
IMPORTANT
● Don’t press any buttons on the VCR or remote while
Plug & Play is in progress.
● If you perform Plug & Play successfully, there’s no need to perform the Clock ( Z pg. 9) and Tuner ( Z pg. 12) procedures. If, however, you want to add or delete channels, refer to “Add Or Delete A Channel” on page 14.
ATTENTION CABLE BOX SUBSCRIBERS
If you perform the Plug & Play procedure . . .
● Select the PBS channel on your cable box before plugging your VCR’s power plug into the AC outlet. (If you have more than one PBS channel, you may have to select an alternative PBS channel if Plug & Play is not successful.)
● If there is no PBS channel in your area, perform the
Manual Clock Set procedure ( Z pg. 11).
● For automatic clock adjustment to take place the VCR's power must be off and the cable box must be set to the
PBS channel at clock adjustment times.
● If you perform Plug & Play successfully, D.S.T. will be set to
“AUTO”. At the D.S.T. adjustment time (
Z
pg. 11), your
VCR's power must be off and your cable box must be set to the host PBS channel in your area for the D.S.T. adjustment to take place. If the clock is not set correctly, change the
D.S.T. setting to “ON” or “OFF. See step 9 of Semi-Auto procedure ( Z pg. 10) or step 6 of Manual procedure ( Z pg. 11).
NOTE:
If the memory backup fails, because of a power outage or because the AC was removed from the VCR, Plug & Play will be performed when power is restored to the VCR.
EN
7
The Plug & Play function sets the clock and tuner channels automatically when power is first connected to the VCR. The antenna cable must be connected for the Plug & Play function.
The time and date can be set automatically from clock setting data that is transmitted by one of the regular TV broadcast channels. We call this TV channel the “Host Channel” and it is a PBS channel in your area.
1
PLUG & PLAY SETUP
Connect the antenna cable to the VCR (
Z
pg. 6). Then connect the VCR’s power plug to an AC outlet. Do not power on the VCR. The clock and tuner channels will automatically be set.
● Auto clock set is performed first. The auto clock set function scans all the channels received by your VCR to find the Host Channel and then sets the clock.
"Auto" blinks on the front display panel during Auto clock set.
● Auto channel set is performed next. The auto channel set function scans all the channels that are receivable by your VCR. It then automatically assigns each receivable channels to the CH▲▼ buttons. It skips non-receivable channels. During auto channel set the channel numbers are displayed as they are scanned and set.
● When Plug & Play has been completed successfully the correct time is displayed.
● If "AUTO CLOCK SET" or "SEMI-AUTO CLOCK SET" is selected at the Override Auto Clock Set screen on page 10, the clock will be adjusted automatically by the Host PBS every hour on the hour (except for
11:00 PM, midnight, 1:00 AM and 2:00 AM) by the incoming PBS channel clock setting data. (This automatic clock adjustment can only be performed when the VCR’s power is turned off. The clock will be adjusted on the hour based on the time displayed on the VCR, not on the actual real time.) The default setting is "AUTO CLOCK SET".
● If an incorrect time is displayed on the front display panel, you may be receiving the clock setting data of a PBS channel from an adjacent time zone, or an incorrect PBS channel from a cable TV system. In this case, perform the Semi-Auto (
Z
pg. 10) or Manual
Clock Set (
Z
pg. 11) procedure. Auto channel set has already taken place and it need not be set again.
● If “- -:- -” appears on the display, your antenna cable may not be connected to the VCR, there may not be a
Host PBS signal available in your area, or your cable box may not be set to the PBS channel. Ensure that the antenna cable is connected correctly. If you use a cable box ensure that your local PBS is selected on your cable box (
Z
ATTENTION CABLE BOX SUBSCRIBERS). Then power on and power off the VCR; the Plug & Play function will be automatically reactivated and "Auto" will be displayed on the VCR's front panel. If everything is connected and set correctly, perform the Manual
Clock Set procedure (
Z
pg. 11). Auto channel set has not yet taken place, so please also perform the “Set
Receivable Channels” procedure (
Z
pg. 12).
During Initial Auto Clock Set
"Auto" blinks.
During Auto Channel Set
The channel numbers are displayed as they are scanned and set.
PM
Plug & Play Completed
The current time (including
AM/PM) is displayed.
8
EN
Language
Turn on the TV and select the VCR channel 3 or 4 (or AV mode).
MENU
CH
5∞
2 q 5
/ 8 6
2
POWER
1
4
7
2
5
8
0
3
6
9
CH 5∞
OK
SHUTTLE PLUS %fi
INITIAL SETTINGS (cont.)
This VCR offers you the choice to view on-screen messages in
English, Spanish or French (not including messages superimposed on the TV picture). Select the desired language using this procedure. The default setting is "ENGLISH".
1
TURN ON THE VCR
Press POWER.
ACCESS ON-SCREEN
MENU
Press MENU as many times as necessary.
2
3
ACCESS CUSTOM SET
SCREEN
At the Main Menu screen, move the highlight bar
(arrow) to “CUSTOM SET” by pressing CH 5∞ or
SHUTTLE PLUS
%fi, then press OK.
MAIN MENU
PROGRAM SET
FUNCTION SET
TUNER SET
= CUSTOM SET
AUTO PICTURE
VIDEO STABILIZER
PRESS ( 5,∞), THEN (OK)
PRESS (MENU) TO END
4
ACCESS LANGUAGE
SELECT SCREEN
The messages are preset to appear in English. If you want to see them in Spanish or
French, move the highlight bar (arrow) to “LANGUAGE
SELECT” by pressing CH
5∞ or SHUTTLE PLUS
%fi, then press OK.
CUSTOM SET
OVERRIDE
AUTO CLOCK SET
=LANGUAGE SELECT
VCR PLUS+ SET-UP
DBS RECEIVER OUTPUT
DBS RECEIVER BRAND SET
PRESS ( 5,∞), THEN (OK)
PRESS (MENU) TO END
5
SELECT LANGUAGE
At the Language Select screen, move the highlight bar (arrow) to the desired language by pressing
CH
5∞ or SHUTTLE PLUS
%fi, then press MENU as many times as necessary to return to the normal screen.
LANGUAGE SELECT
=ENGLISH
ESPAÑOL
FRANCAIS
PRESS ( 5,∞) TO SELECT
PRESS (MENU) TO END
Clock
Turn on the TV and select the VCR channel 3 or 4 (or AV mode).
CH
1
4
7
2
5
8
0
3
6
9
CH
2 q 5
/ 8 6
2
POWER
EN
9
Perform clock setting only if the clock has not been set correctly by the Plug & Play function. Access the Override Auto Clock
Set screen to choose the Auto, Semi-Auto or Manual clock setting procedure. Each procedure starts from step 5. *Auto need only be selected if Semi-Auto or Manual had previously been selected.
Preparation
TURN ON THE VCR
Press POWER.
1
ACCESS ON-SCREEN
MENU
Press MENU as many times as necessary.
2
3
ACCESS CUSTOM SET
SCREEN
At the Main Menu screen, move the highlight bar
(arrow) to “CUSTOM SET” by pressing CH
5∞ or
SHUTTLE PLUS
%fi, then press OK.
MAIN MENU
PROGRAM SET
FUNCTION SET
TUNER SET
=CUSTOM SET
AUTO PICTURE
VIDEO STABILIZER
PRESS ( 5,∞), THEN (OK)
PRESS (MENU) TO END
4
ACCESS CLOCK SET MODE
SELECT SCREEN
Move the highlight bar
(arrow) at the Custom Set screen to “OVERRIDE
AUTO CLOCK SET” by pressing CH 5∞ or
SHUTTLE PLUS
%fi, then press OK.
CUSTOM SET
=OVERRIDE
AUTO CLOCK SET
LANGUAGE SELECT
VCR PLUS+ SET-UP
DBS RECEIVER OUTPUT
DBS RECEIVER BRAND SET
PRESS ( 5,∞), THEN (OK)
PRESS (MENU) TO END
MENU
OK
SHUTTLE PLUS
10
EN
MENU
CH
1
4
7
2
5
8
0
3
6
9
CH
2 q 5 / 8 6
2
OK
SHUTTLE PLUS
INITIAL SETTINGS (cont.)
Semi-Auto
5
SELECT MODE
At the Override Auto
Clock Set screen, move the highlight bar (arrow) to
“SEMI-AUTO CLOCK SET” by pressing CH▲▼ or
SHUTTLE PLUS
%fi, then press OK.
OVERRIDE AUTO CLOCK SET
AUTO CLOCK SET
=SEMI–AUTO CLOCK SET
MANUAL CLOCK SET
PRESS ( 5,∞), THEN (OK)
PRESS (MENU) TO END
6
7
ACCESS SELECT SCREENS
At the Semi-Auto Clock Set screen, move the highlight bar (arrow) to the desired mode by pressing CH▲▼ or SHUTTLE PLUS
%fi, then press OK.
SEMI–AUTO CLOCK SET
= HOST CHANNEL SELECT
TIME ZONE SELECT
D.S.T. SELECT
To select the Host Channel
— step 7
To select the Time Zone — step 8
PRESS ( 5,∞), THEN (OK)
PRESS (MENU) TO END
To select the D.S.T. mode — step 9
NOTE:
The time that has been set previously by the Plug &
Play function will be erased when any of the three settings mentioned above is changed.
SELECT HOST CHANNEL
You can either select
"AUTO", or enter a PBS channel number. For
HOST CHANNEL SELECT
(CATV)
CH AUTO automatic selection, press
MENU if "AUTO" is highlighted on the Host
Channel Select screen. To manually select "AUTO" or
PRESS ( 5,∞) TO SELECT
PRESS (MENU) TO END the PBS channel, press
CH▲▼ or SHUTTLE PLUS
%fi to cycle through
"AUTO" or the channel numbers (hold button down to speed through numbers) and stop when the desired number appears. Press MENU and the Semi-Auto Clock
Set screen reappears.
NOTES:
● For cable box users: Select "AUTO" or the channel on your VCR that receives the cable box channels, and set the cable box to the PBS channel.
● There are some PBS channels that do not transmit clock setting data.
8
9
SELECT TIME ZONE
You can select the zone automatically or manually by pressing CH▲▼ or
SHUTTLE PLUS %fi. If an incorrect time is displayed you may be receiving the
TIME ZONE SELECT
=AUTO
MANUAL clock setting data of a PBS channel from an adjacent
PRESS ( 5,∞) TO SELECT
PRESS (MENU) TO END time zone or from an incorrect PBS channel from a cable TV system. If you selected "AUTO" in step 7 select "MANUAL" and select the correct time zone manually.
● If you selected "AUTO", press MENU to return to the
Semi-Auto Clock Set screen.
● If you selected
"MANUAL", press OK and the screen to the
TIME ZONE SELECT
=ATLANTIC
EASTERN right appears. Move the highlight bar (arrow) to
CENTRAL
MOUNTAIN your choice by pressing
CH▲▼ or SHUTTLE
PLUS
%fi, then press
MENU twice to return to
PACIFIC
ALASKA
HAWAII
PRESS ( 5,∞) TO SELECT
PRESS (MENU) TO END the Semi-Auto Clock Set screen.
SELECT D.S.T. MODE
You have three choices:
a–Select “AUTO” and the adjustment to your VCR’s clock will be made according to the incoming signal from the host channel.
D.S.T. SELECT
=AUTO
ON
OFF
b–Select “ON” and the adjustment will be made
PRESS ( 5,∞) TO SELECT
PRESS (MENU) TO END based on the clock itself.
c–Select “OFF” if Daylight Saving Time doesn’t apply to you.
Move the highlight bar (arrow) to your choice by pressing CH
5∞ or SHUTTLE PLUS %fi, then press
MENU and the Semi-Auto Clock Set screen reappears.
EN
11
Manual
5
6
SELECT MODE
At the Override Auto Clock Set screen ( Z pg. 10), move the highlight bar (arrow) to “MANUAL CLOCK SET” by pressing CH▲▼ or SHUTTLE PLUS
%fi, then press OK.
SET DATE, TIME AND D.S.T.
The Manual Clock Set screen is displayed and the month digit begins blinking. Press the appropriate NUMBER keys
MANUAL CLOCK SET
DATE 1/ 1/97 WED
TIME – –:– – AM
D.S.T.
ON to set the date and time (if only 1 digit, press "0" first).
Press CH▲▼ or SHUTTLE
PLUS
%fi to set AM/PM
PRESS NUMBER KEY (O–9)
OR ( 5,∞), THEN (OK)
PRESS (MENU) TO END and D.S.T. (Daylight Saving Time). Press OK after AM/
PM and D.S.T. settings.
Set D.S.T. to "ON" to set the D.S.T. according to the
VCR's clock or to "OFF" if D.S.T. doesn't apply to you.
When you’re finished with this set-up procedure, press
MENU to start the clock.
7
NOTES:
● CH▲▼ and SHUTTLE PLUS %fi can be used to perform all operations. (In this case, press OK after each setting.)
● At the Manual Clock Set screen, the setting that can be set blinks. When setting of a highlighted item is completed, the highlight bar moves down by 1 line to the next item.
MAKE CORRECTIONS
To change any of the settings, press OK or SHUTTLE
PLUS until the item you want to change blinks, then set as in step 6.
IMPORTANT
Turn the VCR off after performing the Semi-Auto Clock Set procedure. "Auto" will appear on the front display panel when the clock is being set. The current time will appear automatically when the clock is set.
Auto
5
SELECT MODE
At the Override Auto Clock Set screen, move the highlight bar (arrow) to "AUTO CLOCK SET" by pressing CH▲▼ or SHUTTLE PLUS %fi, then power off the VCR. Do not power it on again until the clock has been adjusted. The clock is automatically adjusted on the hour except at 11:00 PM, midnight, 1:00 AM and
2:00 AM. (The clock will be adjusted on the hour based on the time displayed on the VCR, not on the actual real time.)
**AUTO DAYLIGHT SAVING TIME
This function enables automatic adjustment of the VCR’s clock at the start and end of Daylight Saving Time.
With Auto DST activated, . . .
. . . on the first Sunday of April at 2:00 AM, the clock is adjusted to 3:00 AM.
. . . on the last Sunday of October at 2:00 AM, the clock is adjusted to 1:00 AM.
12
EN
Tuner
Turn on the TV and select the VCR channel 3 or 4 (or AV mode).
MENU
CH
1
4
7
2
5
8
0
3
6
9
CH
2 q 5 8 6
2
POWER
OK
SHUTTLE PLUS
INITIAL SETTINGS (cont.)
Set Receivable Channels
TURN ON THE VCR
Press POWER.
1
ACCESS MAIN MENU
SCREEN
Press MENU as many times as necessary.
2
3
ACCESS TUNER SET
SCREEN
Move the highlight bar
(arrow) to "TUNER SET" by pressing CH
5∞ or
SHUTTLE PLUS
%fi, then press OK.
MAIN MENU
PROGRAM SET
FUNCTION SET
=TUNER SET
CUSTOM SET
AUTO PICTURE
VIDEO STABILIZER
PRESS ( 5,∞), THEN (OK)
PRESS (MENU) TO END
4
5
PERFORM AUTO CHANNEL
SET
Move the highlight bar
(arrow) to "AUTO
CHANNEL SET" by pressing CH
5∞ or
SHUTTLE PLUS %fi, then press OK.
TUNER SET
BAND
AFC
=AUTO CHANNEL SET
MANUAL CHANNEL SET
● Receivable channels in your area are automatically assigned to the CH
5∞ buttons, and non-receivable channels are skipped.
PRESS ( 5,∞), THEN (OK)
PRESS (MENU) TO END
AUTO CHANNEL SET
SCANNING...
NOTES:
● At the end of Auto
Channel Set, “SCAN
PRESS (MENU) TO END
COMPLETED” appears on screen.
● If the scan was unsuccessful, “SCAN COMPLETED–
NO SIGNAL” appears on screen. Check the connections and start again.
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary.
MENU
CH
2 q 5 / 8 6
2
EN
13
INFORMATION
The VCR detects the band (TV or CATV) and selects the correct band automatically during Auto Channel Set.
If necessary, you can check the setting at the Band screen after Auto Channel Set has set the channels.
● At the Tuner Set screen, move the highlight bar (arrow) to
"BAND" by pressing CH 5∞ or SHUTTLE PLUS %fi, then press OK.
TUNER SET
=BAND
AFC
AUTO CHANNEL SET
MANUAL CHANNEL SET
BAND
TV
=CATV
PRESS ( 5,∞), THEN (OK)
PRESS (MENU) TO END
PRESS ( 5,∞) TO SELECT
PRESS (MENU) TO END
● Press MENU as many times as necessary to return to the normal screen.
1
4
7
2
5
8
0
3
6
9
CH
OK
SHUTTLE PLUS
14
EN
CH.SKIP
1
4
7
2
5
8
0
3
6
9
CH
NUMBER
ADD
MENU
CH
2 q 5 / 8 6
2
OK
SHUTTLE PLUS
INITIAL SETTINGS (cont.)
Add Or Delete A Channel
1
2
ACCESS TUNER SET
SCREEN
Access by performing steps 2 and 3 of the Tuner procedure on page 12.
● To add a channel, go to step 2.
● To delete a channel, skip to step 4.
ACCESS AFC SCREEN
Move the highlight bar (arrow) to "AFC" by pressing
CH
5∞ or SHUTTLE PLUS %fi, then press OK.
3
MAKE SELECTION
Move the highlight bar
(arrow) to "SPCL" by pressing CH
5∞ or
SHUTTLE PLUS
%fi, then press MENU to return to the Tuner Set screen.
AFC
NORM
=SPCL
● AFC set to SPCL (special) is necessary for tuning on certain CATV systems.
PRESS ( 5,∞) TO SELECT
PRESS (MENU) TO END
4
5
ACCESS MANUAL
CHANNEL SET SCREEN
Move the highlight bar (arrow) to "MANUAL CHANNEL
SET" by pressing CH 5∞ or SHUTTLE PLUS %fi, then press OK.
STORE OR SKIP DESIRED
CHANNEL
Input the channel number using the NUMBER keys or by pressing CH
5∞ or
SHUTTLE PLUS %fi, then press ADD to add or
CH.SKIP to delete. Repeat for each channel you want to store or skip.
MANUAL CHANNEL SET
(CATV)
CH 125 ADD
SELECT CH NO. ADD
PRESS (ADD/SKIP)
PRESS (MENU) TO END
6
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary.
Cable Box
Control
Suggested Location
Place the cable box on top of the VCR. Attach the VCR's
Controller to the top of the VCR with the Controller’s transmitter pointed towards the cable box’s remote sensor.
Attention:
The Controller can also control a DBS receiver. If both a cable box and a DBS receiver are used, position the controller so its signal reaches the remote control sensors of both the cable box and DBS receiver.
* Controller PEAC 0370 is available optionally at your JVC dealer.
Cable box
Your VCR
Controller
Transmitter
Connected to
ANT. IN
Your VCR
Cable box
* Controller (not supplied)
(suggested locations)
CABLE
BOX
Connected to VIDEO/
AUDIO IN
EN
15
This procedure is required if you receive your TV channels through a cable box (descrambler). The Controller allows the
VCR to automatically switch the cable box channel during timer-recording. The Controller is effective for recording shows that have been programmed using VCR Plus+ (
Z
pg. 38) or
On-Screen Timer Programming ( Z pg. 40).
Situate And Connect
Controller
1
SITUATE CONTROLLER
Place the Controller so that the path between its transmitter and the cable box’s remote sensor is unobstructed.
ATTACH CONTROLLER
Fasten securely using the supplied adhesive strips.
2
3
CONNECT CABLE BOX TO
VCR
The connection method depends on the type of cable box you have.
If your cable box has AUDIO and VIDEO OUT connectors . . .
. . . connect them to the AUDIO and VIDEO IN connectors on your VCR; if you use the input connectors other than the rear panel AUDIO and VIDEO OUT connectors, be sure to select the correct external input mode as described in step 4, 5, 9 – 11 on page 46. Set the VCR to channel "AU" to use the cable box.
If your cable box doesn’t have AUDIO and VIDEO
OUT connectors . . .
. . . connect the antenna output connector on the cable box to the ANT.IN connector on the rear of your VCR.
Set the VCR tuner to the same channel as the cable box
RF output (see page 16 also).
NOTE:
Refer to your cable box’s instruction manual during connection.
CONNECT CONTROLLER
TO VCR
Connect to the CABLE BOX connector on your VCR.
4
About Your Cable Box
This VCR has two separate methods to control your Cable Box.
● The VCR's Wireless Remote Control Unit can control your
Cable Box.
This eliminates the need for a separate Cable Box Remote
Control Unit.
● The VCR's Controller can also control your Cable Box.
This allows the VCR to change your Cable Box's channel number during timer recording.
Each method must be set up separately. To set up the VCR's
Remote Control unit, refer to page 49. To set up the Controller go to page 16.
16
EN
Turn on the TV and select the VCR channel 3 or 4 (or AV mode).
1
2
MENU
CH
1
4
7
2
5
8
0
3
6
9
CH
OK
SHUTTLE PLUS
Set Cable Box Output
Channel
TURN ON THE VCR
Press POWER.
2 q 5
/ 8 6
2
POWER
ACCESS MAIN MENU
SCREEN
Press MENU as many times as necessary.
INITIAL SETTINGS (cont.)
3
4
ACCESS CUSTOM SET
SCREEN
Press CH 5∞ or SHUTTLE
PLUS
%fi to move the highlight bar (arrow) to
MAIN MENU
PROGRAM SET
FUNCTION SET
“CUSTOM SET”, then press OK.
TUNER SET
=CUSTOM SET
AUTO PICTURE
VIDEO STABILIZER
PRESS ( 5,∞), THEN (OK)
PRESS (MENU) TO END
ACCESS VCR PLUS+ SET-UP
SCREEN
Press CH
5∞ or SHUTTLE
PLUS
%fi to move the
CUSTOM SET
OVERRIDE
AUTO CLOCK SET highlight bar (arrow) to
“VCR PLUS+ SET-UP”, then press OK.
LANGUAGE SELECT
=VCR PLUS+ SET-UP
DBS RECEIVER OUTPUT
DBS RECEIVER BRAND SET
PRESS ( 5,∞), THEN (OK)
PRESS (MENU) TO END
5
ACCESS CABLE BOX
OUTPUT SCREEN
Press CH
5∞ or SHUTTLE
PLUS
%fi to move the highlight bar (arrow) to
VCR PLUS+ SET-UP
GUIDE CHANNEL SET
“CABLE BOX OUTPUT”, then press OK.
GUIDE CHANNEL MAP
=CABLE BOX OUTPUT
CABLE BOX BRAND SET
PRESS ( 5,∞), THEN (OK)
PRESS (MENU) TO END
6
7
SELECT CABLE BOX
OUTPUT CHANNEL
Your selection depends on how your cable box is connected to your VCR.
If your cable box is connected to your VCR
CABLE BOX OUTPUT
=OFF
ON CH2
ON CH3
ON CH4
ON CH5
ON CH6 using an RF connection . . .
. . . press CH
5∞ or
SHUTTLE PLUS
%fi to
ON LINE
PRESS ( 5,∞) TO SELECT
PRESS (MENU) TO END move the highlight bar (arrow) to the channel number representing the cable box’s output (2–6).
If your cable box is connected to your VCR’s AUDIO/
VIDEO IN connectors . . .
. . . press CH
5∞ or SHUTTLE PLUS %fi to move the highlight bar (arrow) to “ON LINE”.
RETURN TO VCR PLUS+
SET-UP SCREEN
Press MENU.
Set Cable Box Brand
1
TURN ON CABLE BOX
Select a channel other than channel 9 on your Cable
Box.
2
ACCESS CABLE BOX
BRAND SET SCREEN
At the VCR Plus+ Set-Up screen, press CH
5∞ or
SHUTTLE PLUS %fi to move the highlight bar
(arrow) to “CABLE BOX
BRAND SET”, then press
OK.
VCR PLUS+ SET-UP
GUIDE CHANNEL SET
GUIDE CHANNEL MAP
CABLE BOX OUTPUT
=CABLE BOX BRAND SET
PRESS ( 5,∞), THEN (OK)
PRESS (MENU) TO END
3
ENTER CABLE BOX BRAND
Press the appropriate
NUMBER keys to enter the
Cable Box Code from the
CABLE BOX BRAND LIST to the right, then press OK.
CABLE BOX BRAND SET
1
● If the cable box’s channel changes to 9,
PRESS NUMBER KEY (0-9)
THEN (OK)
PRESS (MENU) TO END setting is complete.
● If there are more than one code number listed for your brand of cable box, repeat step 3 until the cable box’s channel changes to 9.
● If you go through all listed code numbers and the channel doesn’t change, try all other numbers between 1 and 69. That is because, maybe, your cable box model is not listed.
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary.
4
You can now set up the VCR Plus+ feature (
Z
pg. 18).
NOTES:
● Although the supplied Controller is compatible with many different cable box brands, it is possible that it will not work with your cable box.
● If your cable box doesn’t respond to any code between 1 and 69, you can’t use the Controller to change cable box channels. In this case, make sure to leave the cable box turned on and tuned to the proper channel before the scheduled start of timer recording.
Please contact your cable company about the possibility of exchanging your current cable box with one that is compatible with your VCR.
● The VCR can only change the cable box channel through the
Controller during timer recording.
● If your cable box is one that can’t be operated with a remote control (has no remote sensor), you can’t use the Controller to change its channels. Make sure to leave the cable box turned on and tuned to the proper channel before the scheduled start of timer recording.
● For customers in U.S.A.: If you are unable to set the Controller, please contact JVC toll free at 1-800-252-5722.
EN
17
CABLE BOX BRAND LIST
BRAND
ARCHER
CABLEVIEW
CITIZEN
CURTIS
DIAMOND
EAGLE
EASTERN
GC BRAND
GEMINI
GENERAL ELECTRIC
GENERAL INSTRUMENTS
HAMLIN
JERROLD
MACOM, HITACHI
MAGNAVOX
MOVIETIME
NSC
OAK
PANASONIC
PHILIPS
PIONEER
PULSER
RCA
REGAL
REGENCY
SAMSUNG
SCIENTIFIC ATLANTA
SIGMA
SL MARX
SPRUCER
STARGATE
SYLVANIA
TEKNIKA
TELECAPTION
TELEVIEW
TEXSCAN
TOCOM
UNIKA
UNIVERSAL
VIDEOWAY
VIDEO TECH
VIDTER
VIEWSTAR
ZENITH
CODE
49, 52, 53, 54
49, 53
49, 53
9, 10, 62, 63
52, 53, 54
30, 31, 32, 33, 34, 35, 36, 37
51
49, 53
8, 56
67
1, 2, 3, 4, 5, 6, 7,8
15, 16, 17,18
1, 2, 3, 4, 5, 6, 7, 8
57, 58, 59
30, 31, 32, 33, 34, 35, 43
44, 45, 46
44, 45, 46
19, 20, 21, 30, 47, 48
24, 25, 26
30, 31, 32, 33, 42
13, 14
49, 53
24, 25, 26
15, 16, 17, 18, 33
51
8, 13, 49, 50
9, 10, 62, 63
19, 20, 21
8, 13, 49, 50
24, 25, 26
8, 13, 49, 50
29
68, 69
27
8, 13, 49, 50
28, 29
22, 23, 64, 65, 66
52, 53, 54
38, 39, 40, 41
11, 12, 60, 61
55
55
30, 31, 32, 33, 34, 35, 36, 37
11, 12, 60, 61
18
EN
VCR Plus+
Setup
Turn on the TV and select the VCR channel 3 or 4 (or AV mode).
MENU
CH
1
4
7
2
5
8
0
3
6
9
CH
2 q 5 / 8 6
2
POWER
OK
SHUTTLE PLUS
INITIAL SETTINGS (cont.)
The VCR Plus+ timer programming system eliminates the need to input channel, date, start and stop time data when setting the timer record function. Simply key in the PlusCode number for the TV program you wish to record (found in most TV listings) and the VCR’s timer is automatically programmed.
Depending on the TV or cable stations that you receive and the channel numbers that they are received on in your area, you may have to make certain changes in your VCR’s “Guide Channel Set” menu to get proper results. Please read the following information carefully to find out which tasks you need to perform.
Before VCR Plus+ setup you must have performed the following procedures:
● Plug & Play ( Z
pg. 7)
or
Clock setting (
Tuner setting (
● Cable box setting if you receive your TV channels through a cable box (
Z
Z
pg. 9)
Z
pg. 12)
pg. 15)
Channel Number Matching
Most TV listings have a chart indicating the “Guide Channel” number assigned to each station for purposes of VCR Plus+ programming. Check the chart in your TV listings and see if the
Guide Channel numbers listed for the stations you receive are the same as the channel number on which each is received by your VCR or cable box.
**SPECIAL NOTES FOR CABLE SUBSCRIBERS**
● In many instances, cable TV stations have VCR Plus+ Guide
Channel numbers that DO NOT match the number of the channel on which you receive the station. Check your TV listings, or contact your cable supplier for details.
● Many normal broadcast TV stations can be viewed on cable.
Check your TV listing, or contact your cable supplier for details.
If the numbers match, go directly to “VCR Plus+ Timer
Programming” ( Z pg. 38).
If the numbers are different, and you want to be able to timer record programs from those stations, you have to inform the
VCR of the mismatch. Go to step 1. If you will not want to timer record from those stations, you can go directly to “VCR Plus+
Timer Programming” (
Z
pg. 38).
1
TURN ON THE VCR
Press POWER.
ACCESS MAIN MENU
SCREEN
Press MENU as many times as necessary.
2
3
4
5
ACCESS CUSTOM SET
SCREEN
Press CH 5∞ or SHUTTLE
PLUS
%fi to move the highlight bar (arrow) to
MAIN MENU
PROGRAM SET
FUNCTION SET
“CUSTOM SET”, then press OK.
TUNER SET
=CUSTOM SET
AUTO PICTURE
VIDEO STABILIZER
PRESS ( 5,∞), THEN (OK)
PRESS (MENU) TO END
ACCESS VCR PLUS+ SET-UP
SCREEN
Press CH
5∞ or SHUTTLE
PLUS
%fi to move the
CUSTOM SET
OVERRIDE
AUTO CLOCK SET highlight bar (arrow) to
“VCR PLUS+ SET-UP”, then press OK.
LANGUAGE SELECT
=VCR PLUS+ SET-UP
DBS RECEIVER OUTPUT
DBS RECEIVER BRAND SET
PRESS ( 5,∞), THEN (OK)
PRESS (MENU) TO END
ACCESS GUIDE CHANNEL
SET SCREEN
Press CH
5∞ or SHUTTLE
PLUS
%fi to move the highlight bar (arrow) to
VCR PLUS+ SET-UP
=GUIDE CHANNEL SET
GUIDE CHANNEL MAP
“GUIDE CHANNEL SET”,
CABLE BOX OUTPUT then press OK.
CABLE BOX BRAND SET
6
PRESS ( 5,∞), THEN (OK)
PRESS (MENU) TO END
INPUT GUIDE CHANNEL
NUMBER
Press CH 5∞, SHUTTLE
PLUS
%fi or the appropriate NUMBER
(Ex.) When inputting the
Guide Channel number
6 for WNJU(Ind.) keys to input the Guide
Channel number as shown in the TV listing. Then press OK.
GUIDE CHANNEL SET
GUIDE CH : 6
VCR CH : 6
● If you receive your channels with a cable box and if you have
PRESS NUMBER KEY (0-9)
OR ( 5∞), THEN (OK)
PRESS (MENU) TO END properly set your
Controller, “CABLE CH” appears in place of “VCR
CH”. If not, refer to pages 15–16 and re-perform the procedure.
EN
19
7
INPUT RECEIVING CHANNEL
NUMBER
Press CH 5∞, SHUTTLE
PLUS
%fi or the appropriate NUMBER keys
(Ex.) If WNJU(Ind.) is received on channel 47
GUIDE CHANNEL SET to input the number of the channel on which the GUIDE CH : 6
VCR CH : 47
Guide Channel’s broadcasts are received. Then press OK.
● If there is more than one mismatch, repeat steps 6 and 7 for each instance.
PRESS NUMBER KEY (0-9)
OR ( 5∞), THEN (OK)
PRESS (MENU) TO END
RETURN TO VCR PLUS+
SET-UP SCREEN
Press MENU.
8
9
10
CHECK INPUT DATA
Press CH
5∞ or SHUTTLE
PLUS
%fi to move the
VCR PLUS+ SET-UP highlight bar (arrow) to
“GUIDE CHANNEL MAP”,
GUIDE CHANNEL SET
=GUIDE CHANNEL MAP
CABLE BOX OUTPUT then press OK.
CABLE BOX BRAND SET
● The Guide Channel and
VCR or cable box
PRESS ( 5,∞), THEN (OK)
PRESS (MENU) TO END channel numbers you input appear on the screen in ascending order. Check to ensure
GUIDE CHANNEL MAP
GUIDE : VCR GUIDE : VCR you’ve entered them correctly.
● If you entered more than
10 sets of numbers, press
6 : 47
12 : 41
33 : 28
10 : 55
15 : 38
67 : 49
OK to see the next set of
PRESS (OK) TO NEXT
PRESS (MENU) TO END numbers.
● Guide Channel Map contains only the Guide Channels and VCR or CABLE channels that you entered.
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary.
You can now use VCR Plus+ for quick and simple timer programming ( Z pg. 38).
20
EN
DBS Receiver
Control
Suggested Location
Place the DBS (Direct Broadcast Satellite) receiver on top of the
VCR. Attach the VCR's Controller to the top of the VCR with the
Controller’s transmitter pointed towards the DBS receiver's remote sensor.
Attention:
The Controller can also control a cable box. If both a DBS receiver and a cable box are used, position the controller so its signal reaches the remote control sensors of both the DBS receiver and cable box.
* Controller PEAC 0370 is available optionally at your
JVC dealer.
DBS receiver
Your VCR
DBS receiver
* Controller (not supplied)
(suggested locations)
Controller
Transmitter
Your VCR
Connected to
ANT. IN
CABLE
BOX
Connected to VIDEO/
AUDIO IN
About Your DBS Receiver
This VCR has two separate methods to control your DBS Receiver.
● The VCR's Wireless Remote Control Unit can control your
DBS Receiver.
This eliminates the need for a separate DBS Receiver Remote
Control Unit.
● The VCR's Controller can also control your DBS Receiver.
This allows the VCR to change your DBS receiver's channel number during timer recording.
Each method must be set up separately. To set up the VCR's
Remote Control unit, refer to page 50. To set up the Controller go to page 21.
INITIAL SETTINGS (cont.)
The following procedure is required if you receive satellite channels through a DBS (Direct Broadcast Satellite) receiver and you want your VCR to change to receiver's channels during timer recording.
The VCR can control the DBS Receiver during timer recording using its Controller.
NOTES:
● The Controller can automatically change the DBS Receiver channels when the VCR has been programmed using On-
Screen Timer Programming ( Z pg. 40).
Because satellite programming does not use PlusCode; the
Controller can not change the DBS Receiver channels during
VCR Plus+ Timer Recording.
● If a cable box is used simultaneously, it is recommended to connect the DBS receiver to your VCR using A/V inputs.
Situate And Connect Controller
1
SITUATE CONTROLLER
Place the Controller so that the path between its transmitter and the DBS receiver's remote sensor is unobstructed.
ATTACH CONTROLLER
Fasten securely using the supplied adhesive strips.
2
3
CONNECT DBS RECEIVER
TO VCR
The connection method depends on the type of DBS receiver you have.
If your DBS receiver has AUDIO and VIDEO OUT connectors . . .
. . . connect them to the AUDIO and VIDEO IN connectors on your VCR; if you use the input connectors other than the rear panel AUDIO and VIDEO OUT connectors, be sure to select the correct external input mode as described in step 4, 5, 9 – 11 on page 46. Set the VCR to channel "AU" to use the DBS receiver.
If your DBS receiver doesn’t have AUDIO and VIDEO
OUT connectors . . .
. . . connect the antenna output connector on the DBS receiver to the ANT. IN connector on the rear of your
VCR.
Set the VCR tuner to the same channel as DBS receiver
RF output. (See page 21 also.)
NOTE:
Refer to your DBS receiver's instruction manual during connection.
CONNECT CONTROLLER
TO VCR
Connect to the CABLE BOX connector on your VCR.
4
Turn on the TV and select the VCR channel 3 or 4 (or AV mode).
MENU
CH
1
4
7
2
5
8
0
3
6
9
CH
2 q 5 8 6
2
POWER
OK
SHUTTLE PLUS
EN
21
Set DBS Receiver Output
Channel
1
TURN ON THE VCR
Press POWER.
● Set the VCR to the channel (3 or 4 or AU) on which the signals from the DBS receiver are received.
ACCESS MAIN MENU
SCREEN
Press MENU as many times as necessary.
2
3
ACCESS CUSTOM SET
SCREEN
Press CH
5∞ or SHUTTLE
PLUS %fi to move the highlight bar (arrow) to
MAIN MENU
PROGRAM SET
FUNCTION SET
“CUSTOM SET”, then press OK.
TUNER SET
= CUSTOM SET
AUTO PICTURE
VIDEO STABILIZER
PRESS ( 5,∞), THEN (OK)
PRESS (MENU) TO END
4
ACCESS DBS RECEIVER
OUTPUT SCREEN
Press CH
5∞ or SHUTTLE
PLUS
%fi to move the highlight bar (arrow) to
CUSTOM SET
OVERRIDE
AUTO CLOCK SET
LANGUAGE SELECT
“DBS RECEIVER OUT-
PUT”, then press OK.
VCR PLUS+ SET-UP
=DBS RECEIVER OUTPUT
DBS RECEIVER BRAND SET
PRESS ( 5,∞), THEN (OK)
PRESS (MENU) TO END
5
6
SELECT DBS RECEIVER
OUTPUT CHANNEL
Your selection depends on how your DBS receiver is connected to your VCR.
If your DBS receiver is connected to your VCR
DBS RECEIVER OUTPUT
=OFF
ON CH2
ON CH3
ON LINE using an RF connection . . .
. . . press CH
5∞ or
SHUTTLE PLUS
%fi to
PRESS ( 5,∞) TO SELECT
PRESS (MENU) TO END move the highlight bar (arrow) to the channel number representing the DBS receiver's output (3–4).
If your DBS receiver is connected to your VCR’s
AUDIO/VIDEO IN connectors . . .
. . . press CH
5∞ or SHUTTLE PLUS %fi to move the highlight bar (arrow) to “ON LINE”.
RETURN TO CUSTOM SET
SCREEN
Press MENU.
22
EN
MENU
1
4
7
2
5
8
0
CH
3
6
9
CH
OK
2 q 5 / 8 6
2
NUMBER
SHUTTLE PLUS
NOTES:
● Depending on the type of DBS receiver, it is possible that the
Controller will not work with it.
● If your DBS receiver doesn’t respond to the code, you can’t use the Controller to change satellite channels. In this case, make sure to leave the DBS receiver turned on and tuned to the proper channel before the scheduled start of timer recording.
● The VCR can only change the satellite channel through the
Controller during timer recording.
● If your DBS receiver is one that can’t be operated with a remote control (has no remote sensor), you can’t use the
Controller to change its channels. Make sure to leave the DBS receiver turned on and tuned to the proper channel before the scheduled start of timer recording.
● For customers in U.S.A.: If you are unable to set the Controller, please contact JVC toll free at 1-800-252-5722.
INITIAL SETTINGS (cont.)
Set DBS Receiver Brand
1
TURN ON DBS RECEIVER
Select a channel other than channel 55, 100 or 205 on your DBS receiver.
2
ACCESS DBS RECEIVER
BRAND SET SCREEN
At the Custom Set screen, press CH
5∞ or SHUTTLE
PLUS
%fi to move the highlight bar (arrow) to
“DBS RECEIVER BRAND
SET”, then press OK.
CUSTOM SET
OVERRIDE
AUTO CLOCK SET
LANGUAGE SELECT
VCR PLUS+ SET-UP
DBS RECEIVER OUTPUT
=DBS RECEIVER BRAND SET
PRESS ( 5,∞), THEN (OK)
PRESS (MENU) TO END
3
ENTER DBS RECEIVER
BRAND
Press the appropriate
NUMBER keys to enter the
DBS Receiver Code from the following list, then
DBS RECEIVER BRAND SET
80 press OK.
The unit is pre-set to code
80 (RCA) when shipped.
PRESS NUMBER KEY (0-9)
THEN (OK)
● If the DBS receiver's
PRESS (MENU) TO END channel changes as follows, setting is complete:
RCA or SONY [ 205
PRIMESTAR [ 55
ECHOSTAR [ 100
● After OK is pressed, the program currently received through the DBS receiver will appear for about 10 seconds.
BRAND
RCA (DSS)
SONY (DSS)
PRIMESTAR
ECHOSTAR
CODE
80
81
90
91
4
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary.
SIMPLE PLAYBACK AND RECORDING
Simple
Playback
Turn on the TV and select the VCR channel 3 or 4 (or AV mode).
PLAY
REW
2 q 5 8 6
2
EN
23
1
LOAD A CASSETTE
Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is pointing towards the VCR. Don’t apply too much pressure when inserting.
● The VCR’s power comes on automatically.
● The counter is automatically reset to "0H 00M 00S".
● If the cassette's record safety tab has been removed, playback begins automatically.
FIND PROGRAM START
POINT
Press REW or FF if you want to rewind or fast forward to a different section of the tape.
2
3
START PLAYBACK
(
Press PLAY. "AUTO PICTURE" appears on screen
Z
pg. 35).
4
STOP PLAYBACK
Press STOP or STOP/EJECT. Then press STOP/EJECT to remove the cassette.
REW (Rewind)
1
4
7
2
5
8
0
3
6
9
FF (Fast-Forward)
Usable cassettes
Full-Size VHS
T-30 (ST-30**)
T-60 (ST-60**)
T-90
T-120 (ST-120**)
T-160 (ST-160**)
ST-210**
Compact VHS*
TC-20 (ST-C20**)
TC-30 (ST-C30**)
TC-40 (ST-C40**)
* Compact VHS camcorder recordings can be played on this video recorder. Simply place the recorded cassette into a VHS Cassette Adapter and it can be used just like any full-sized VHS cassette.
** This video recorder can record on regular VHS and
Super VHS cassettes. However, it will record and play back regular VHS signals only. It is not possible to play back Super VHS recordings.
24
EN
Simple
Recording
SIMPLE PLAYBACK AND RECORDING (cont.)
Turn on the TV and select the VCR channel 3 or 4 (or AV mode).
1
4
7
2
5
8
0
CH
3
6
9
REC
2 q / 8 6
2
STOP/EJECT
ENTER
NUMBER
1
2
3
4
5
6
LOAD A CASSETTE
Make sure the record safety tab is intact. If not, cover the hole with adhesive tape before inserting the cassette.
SELECT RECORDING
CHANNEL
Press CH
5∞. Or press the appropriate NUMBER keys, then press ENTER. (The channel changes after a few seconds whether you press ENTER or not.)
● If you use the RF connection, by pressing the TV/VCR button, select VCR mode to view the program to be recorded.
SET TAPE SPEED
Press SP/EP to set the recording speed.
START RECORDING
Press and hold REC and press PLAY on the remote control, or press REC on the VCR's front panel.
PAUSE/RESUME
RECORDING
Press PAUSE. Press PLAY to resume recording.
● During record pause, you can change the recording channel by using the CH 5∞ buttons or NUMBER keys.
STOP RECORDING
Press STOP or STOP/EJECT. Then press STOP/EJECT to remove the cassette.
TV/VCR
CH
SP/EP
PLAY
PAUSE
Accidental erasure prevention
● To prevent accidental recording on a recorded cassette, remove its record safety tab.
To record on it later, cover the hole with adhesive tape.
REC
Record safety tab
PLAYBACK AND RECORDING FEATURES
Playback
Features
CH
PLAY
2 q 5
/ 8 6
2
Still Picture/Frame-By-
Frame Playback
1
PAUSE DURING PLAYBACK
Press PAUSE. If there is vertical jitter, use the
CH
5 or ∞ button to correct the picture.
2
ACTIVATE FRAME-BY-
FRAME PLAYBACK
Press PAUSE repeatedly to advance one frame at a time.
OR
Press SHUTTLE PLUS ™ or £ repeatedly to advance one frame at a time.
Press SHUTTLE PLUS £ for forward frame by frame playback or SHUTTLE PLUS ™ for reverse frame by frame.
To resume normal playback, press PLAY.
EN
25
REW
PLAY
1
4
7
2
5
8
0
3
6
9
CH
FF
PAUSE
SHUTTLE PLUS
Slow Motion/Reverse Slow
Motion
1
ACTIVATE SLOW-MOTION
PLAYBACK
During still picture, press and hold SHUTTLE PLUS
™ or £. Release to return to still picture.
OR
For hands-free slow-motion, press SHUTTLE PLUS ™ during playback to decrease speed in the forward direction. Continue to press ™ to select the various slow motion, reverse slow motion, reverse play and reverse search modes.
To resume normal playback, press PLAY.
NOTE:
If noise bars appear during slow motion, press CH 5 or ∞ a few times to remove the noise bars from screen.
High-Speed Search
1
ACTIVATE HIGH-SPEED
SEARCH
During playback or still press FF for forward high-speed search, or REW for reverse high-speed search.
To resume normal playback, press PLAY.
NOTE:
For short searches, during playback or still press and hold FF or
REW for over 2 seconds. When released, normal playback resumes.
Variable-Speed Search/
Reverse Motion Playback
1
ACTIVATE VARIABLE-SPEED
SEARCH
During playback, press SHUTTLE PLUS ™ or £.
● To increase the speed in the forward direction, press £ repeatedly to select the various forward search modes.
● To decrease the speed in the forward direction, press ™.
● To play in reverse slow motion, and in reverse play mode, continue to press ™ after selecting all the forward slow motion modes.
To resume normal playback, press PLAY.
26
EN
REW
1
4
7
2
5
8
0
3
6
9
CH
PLAYBACK AND RECORDING FEATURES (cont.)
2 q 5
/ 8 6
2
Manual Tracking
Once playback begins, the VCR’s automatic tracking function is engaged. If noise appears in the picture, you can override this and make the adjustment manually.
1
2
3
ENGAGE MANUAL
TRACKING MODE
During playback, press the CH
5 and ∞ buttons on the
VCR's front panel simultaneously to cancel the automatic tracking mode and enable manual tracking adjust.
ADJUST MANUAL
TRACKING
Press CH
5 or ∞ on the VCR's front panel or remote.
Press briefly for fine adjust, or press and hold for coarse adjust. Watch the screen and continue adjusting until optimum picture and sound quality are achieved.
RE-ENGAGE AUTOMATIC
TRACKING
Press the CH 5 and ∞ buttons on the VCR's front panel simultaneously.
● When automatic tracking is re-engaged, Auto Picture is automatically activated.
CH
FF
NOTES:
● To obtain a noiseless still picture it may be necessary to adjust tracking in slow playback and then engage Pause.
● Manual tracking is possible during hands-free slow-motion.
During hands-free slow-motion playback, simply press CH 5 or ∞ on the VCR's front panel or remote to adjust tracking.
Tape Position Indicator
The Tape position indicator appears on screen when, from the stop mode, you press FF, REW, or perform an Index Search or Instant
ReView. The position of " " in relation to "B" (Beginning) or "E"
(End) shows you where you are on the tape.
B
+ + +
COUNT
E
0:33:27
NOTE:
"SUPERIMPOSE" must be set to "ON", or the indicator will not appear (
Z
pg. 28).
MENU
CH
1
4
7
2
5
8
0
3
6
9
CH
2 q 5 / 8 6
2
OK
SHUTTLE PLUS
EN
27
Video Stabilizer
You can correct vertical vibration when playing back unstable
EP recordings that were made on another VCR. When this function is set to "ON", vertical vibration will be automatically corrected. *The default setting is "OFF".
ACCESS MAIN MENU
SCREEN
Press MENU as many times as necessary.
1
2
ACCESS VIDEO STABILIZER
SCREEN
Move the highlight bar
(arrow) to "VIDEO
STABILIZER" by pressing
CH 5∞ or SHUTTLE PLUS
%fi, then press OK.
MAIN MENU
PROGRAM SET
FUNCTION SET
TUNER SET
CUSTOM SET
AUTO PICTURE
= VIDEO STABILIZER
PRESS ( 5,∞), THEN (OK)
PRESS (MENU) TO END
3
ACTIVATE VIDEO
STABILIZER
Move the highlight bar
(arrow) to "ON" by pressing CH
5∞ or
SHUTTLE PLUS
%fi.
VIDEO STABILIZER
=ON
OFF
4
PRESS ( 5,∞) TO SELECT
PRESS (MENU) TO END
RETURN TO NORMAL
SCREEN
Press MENU.
NOTES:
● Regardless of the setting, this function has no effect with SP recordings, during recording and during special-effects playback.
● When you finish viewing the tape, be sure to set it back to
"OFF".
28
EN
MENU
1
4
7
2
5
8
0
3
6
9
CH
PLAYBACK AND RECORDING FEATURES (cont.)
CH q / 8 6
OSD
OK
2 2
Superimpose
This function, switchable between ON and OFF, determines whether or not operational indicators will appear on screen.
ACCESS MAIN MENU
SCREEN
Press MENU as many times as necessary.
1
2
ACCESS FUNCTION SET
SCREEN
Move the highlight bar (arrow) to "FUNCTION SET" by pressing CH
5∞ or SHUTTLE PLUS %fi, then press OK.
3
ACCESS SUPERIMPOSE
SCREEN
Move the highlight bar
(arrow) to "SUPERIMPOSE" by pressing CH
5∞ or
SHUTTLE PLUS
%fi, then press OK.
FUNCTION
AUTO TIMER
=SUPERIMPOSE
2ND AUDIO
AUDIO MONITOR
AUX INPUT
SPECIAL FUNCTION
PRESS ( 5,∞), THEN (OK)
PRESS (MENU) TO END
4
SELECT MODE
Move the highlight bar
(arrow) to "ON" or "OFF" by pressing CH 5∞ or
SHUTTLE PLUS
%fi.
SUPERIMPOSE
=ON
OFF
SHUTTLE PLUS
To recall an indication
1 Press OSD.
n All indications corresponding to the current status are displayed for 5 seconds, leaving the counter information, and RECORD/PAUSE if in the Record Pause mode, on the screen. (No indication during still and search.)
2 Press OSD again to clear the display.
PRESS ( 5,∞) TO SELECT
PRESS (MENU) TO END
5
NOTE:
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary.
If you engage the Record Pause mode, RECORD/PAUSE (or ITR followed by the elapsed time/PAUSE) is displayed whether
"SUPERIMPOSE" is set to "ON" or "OFF".
The superimposed indication on the TV screen tells you what the VCR is doing.
Tuned-in channel or AUX(iliary) mode
When the channel is changed, the new channel is displayed on the screen for 5 seconds.
Clock time
Tape position indicator
"Cassette Loaded" mark
When a cassette is loaded, the mark is displayed for 5 seconds. It blinks when the
VCR's EJECT button is pushed.
CH 125
THU 12:00 AM
RECORD
PAUSE
] SP
B + + + E
NORM
HI–FI COUNT
INDEX-1
MEMORY OFF
–1:23:45
Audio mode indicators
Operation mode
When the operation mode is changed, the new mode is displayed — RECORD
(5 sec.), PLAY (5 sec.), FF/REW (5 sec.
when engaged from Stop mode),
RECORD PAUSE (for as long as Pause is engaged), and ITR *:** (5 sec.).
Tape speed indicator
INDEX indication
Counter reading
Counter memory on/off
MENU
CH
1
4
7
2
5
8
0
3
6
9
CH
2 q 5 8 6
2
OK
SHUTTLE PLUS
EN
29
Select The Soundtrack
Your VCR can record two soundtracks simultaneously (Normal and Hi-Fi) and play back the selected one, or both together.
1
ACCESS MAIN MENU
SCREEN
Press MENU as many times as necessary during playback or when VCR is in stop mode.
2
ACCESS FUNCTION SET
SCREEN
Move the highlight bar (arrow) to "FUNCTION SET" by pressing CH
5∞ or SHUTTLE PLUS %fi, then press OK.
3
ACCESS AUDIO MONITOR
SCREEN
Move the highlight bar
(arrow) to "AUDIO
MONITOR" by pressing
CH
5∞ or SHUTTLE PLUS
%fi, then press OK.
FUNCTION
AUTO TIMER
SUPERIMPOSE
2ND AUDIO
=AUDIO MONITOR
AUX INPUT
SPECIAL FUNCTION
PRESS ( 5,∞), THEN (OK)
PRESS (MENU) TO END
4
SELECT MODE
You have three choices:
a– Hi-Fi
b– Normal
c– Mix
AUDIO MONITOR
=HI–FI
NORM
MIX
Move the highlight bar
(arrow) to your choice by pressing CH
5∞ or
SHUTTLE PLUS
%fi.
PRESS ( 5,∞) TO SELECT
PRESS (MENU) TO END
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary.
5
NOTES:
● If the tape being played back has no Hi-Fi soundtrack, the
Normal soundtrack will be heard no matter what choice you make at the Audio Monitor screen.
● If RF connection is used for TV, even if Hi-Fi audio monitor is selected the sound will be mono and will be reproduced in both loudspeakers.
30
EN
REVIEW
REW
1
4
7
2
5
8
0
REW
3
6
9
PLAYBACK AND RECORDING FEATURES (cont.)
PLAY
2 q 5
/ 8 6
2
Index Search
Index codes are placed on the tape at the start of each recording. You can find and automatically play back from the start of any recording using the Index Search function.
1
START SEARCH
While the tape is stopped, press SHUTTLE PLUS ™ or £.
2
ACCESS DISTANT CODE
To access a recording 2–9 index codes away, press
SHUTTLE PLUS ™ or £ repeatedly until the correct number is displayed on screen (only if SUPER-
IMPOSE is set to ON (
Z
pg. 28). Playback begins automatically when the desired recording is located.
● If necessary press REW or FF when play starts to search visually to find the very beginning of the desired program.
NOTE:
An index code is not placed on the tape when recording is paused and then resumed.
PLAY
FF
SKIP SEARCH
SHUTTLE PLUS
Instant ReView
At the press of a button, you can power up your VCR, rewind the tape and begin viewing the most recent timer-recorded program.
1
ACTIVATE INSTANT REVIEW
After ensuring that the Timer mode is disengaged, press
REVIEW.
● The power comes on and the VCR searches for the index code indicating the start of the last timer-recorded program, then begins playback automatically.
● You can access a program 2–9 index codes away from the current position on the tape. If, for example, you have 5 programs recorded and you want to watch the third one, press REVIEW three times.
● If necessary press REW or FF when play starts to search visually to find the very beginning of the desired program.
● If the tape is already rewound when REVIEW is pressed, it will play the tape from the beginning. It will not fast forward to an index code.
● The Instant Review function will also operate if the
VCR's power is on.
Skip Search
1
SKIP OVER UNWANTED
SECTIONS
Press SKIP SEARCH 1 to 4 times during playback. Each press initiates a 30-second period of fast- motion playback. Normal playback resumes automatically.
NOTE:
To return to normal playback during a Skip Search, press PLAY.
C.RESET
REW
1
4
7
2
5
8
0
3
6
9
PLAY
STOP
2 q 5
/ 8 6
2
POWER
TIMER
EN
31
Repeat Playback
1
2
START REPEAT
Press and hold PLAY (until "PLAY" blinks on the front display panel) during playback, then release.
V C R
SP
PLAY
H M S
● The entire tape is played back 20 times.
STOP REPEAT
To stop, press STOP at any time.
NOTE:
Pressing PLAY, REW, FF, PAUSE or SHUTTLE PLUS
™ or £ also stops Repeat Playback.
Counter Reset
1
RESET COUNTER TO ZERO
Press C.RESET.
NOTE:
By pressing the DISPLAY button, you can change the display to show the counter reading, channel number or clock time. (Channel number is not displayed during playback.)
PLAY
DISPLAY
REW
FF
C.MEMORY
SHUTTLE PLUS
Next-Function Memory
The Next Function Memory “tells” the VCR what to do after rewinding. * Before continuing, ensure that the VCR is in stop mode.
a– For Automatic Start Of Playback After Tape Rewind . . .
. . . press REW, then press PLAY within 2 seconds.
b– For Automatic Power Off After Tape Rewind . . .
. . . press REW, then press POWER within 2 seconds.
c– For Automatic Timer Standby After Tape Rewind . . .
. . . press REW, then press TIMER within 2 seconds.
NOTE:
If you want the "next function" to automatically start when the counter reads "0H 00M 00S" (instead of at the beginning of the tape), press C. MEMORY so that the counter memory indicator appears on the front display panel before pressing REW.
Counter Memory
When REW or FF is pressed, with the Counter Memory activated, the tape will return to the counter position "zero".
1
2
ACTIVATE COUNTER
MEMORY
Press C.RESET during playback at a point you want to have quick access to later. The counter reads “0H 00M 00S”.
Then press C.MEMORY. The Counter Memory indicator
("M") in the front display panel lights.
RETURN TO COUNTER
POSITION ZERO
Press STOP (during playback), then press REW or FF.
The tape rewinds or fast-forwards and stops at approximately “0H 00M 00S” automatically.
● To cancel Counter Memory, press C.MEMORY.
32
EN
MENU
1
4
7
2
5
8
0
3
6
9
CH
PLAYBACK AND RECORDING FEATURES (cont.)
CH
OK
2 q 5 8 6
POWER
SHUTTLE PLUS
2
AV COMPU LINK Playback
Your VCR is compatible with JVC’s AV COMPU LINK components, including amplifiers (or receivers) and televisions. AV COMPU
LINK provides one touch control of the audio and video components that are linked via their AV COMPU LINK connectors.
For example: simply load a cassette in the VCR and press PLAY and the AV COMPU LINK components automatically power on, the TV's AV mode is selected and the VCR goes into play mode.
(PLAY need not be pressed if the cassette's record safety tab is removed.)
1
MAKE CONNECTION
Connect your VCR to an AV COMPU LINK component as shown in the illustration on page 33.
● The mini-plug cable is a mono 3.5 mm mini-plug to mono 3.5 mm mini-plug connector.
TURN ON THE VCR
Press POWER.
2
ACCESS MAIN MENU
SCREEN
Press MENU as many times as necessary.
3
4
5
ACCESS FUNCTION SET
SCREEN
Press CH
5∞ or SHUTTLE PLUS %fi to move the highlight bar (arrow) to “FUNCTION SET”, then press
OK.
ACCESS SPECIAL
FUNCTION SCREEN
Press CH
5∞ or SHUTTLE
PLUS
%fi to move the
FUNCTION
AUTO TIMER
SUPERIMPOSE highlight bar (arrow) to
2ND AUDIO
“SPECIAL FUNCTION”,
AUDIO MONITOR then press OK.
AUX INPUT
=SPECIAL FUNCTION
PRESS ( 5,∞), THEN (OK)
PRESS (MENU) TO END
Example
MENU
CH
PLAY
1
4
7
2
5
8
0
3
6
9
CH
2 q 5 / 8 6
2
6
EN
33
ENABLE AV COMPU LINK
PLAYBACK
Press CH 5∞ or SHUTTLE
PLUS
%fi to move the highlight bar (arrow) to
SPECIAL FUNCTION
PAUSE
=AV COMPU-LINK
“AV COMPU LINK”.
PRESS ( 5,∞) TO SELECT
PRESS (MENU) TO END
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary.
7
8
PERFORM AV COMPU LINK
PLAYBACK
Simply insert a cassette and press PLAY (if the cassette’s record safety tab has been removed, playback begins automatically). Linked components are turned on, and the TV set to its AV mode, automatically!
NOTE:
Connection varies depending on the type of JVC TV you have.
Please refer to the TV’s instruction manual when making this connection.
SHUTTLE PLUS
PAUSE/
AV COMPU LINK
Your VCR
AV COMPU
LINK II
(VCR ONLY)
Mini-plug cable
(not supplied)
AUDIO IN
VIDEO
OUT
AUDIO
OUT
Audio/Video cable
(not supplied)
AV COMPU LINK
Television
VIDEO IN
34
EN
MENU
1
4
7
2
5
8
0
CH
3
6
9
PLAYBACK AND RECORDING FEATURES (cont.)
Auto Picture
Turn on the TV and select the VCR channel 3 or 4 (or AV mode).
CH
OK
2 q 5
8 6
POWER
SHUTTLE PLUS
2
Auto Picture compensates for variations in tape characteristics to ensure the best possible playback picture. It checks and compensates for the condition of the tape at the beginning of automatic tracking when playback is selected.
Preparation
TURN ON THE VCR
Press POWER.
1
ACCESS MAIN MENU
SCREEN
Press MENU as many times as necessary.
2
3
ACCESS AUTO PICTURE
SCREEN
Press CH
5∞ or SHUTTLE
PLUS %fi to move the highlight bar (arrow) to
MAIN MENU
PROGRAM SET
FUNCTION SET
“AUTO PICTURE”, then press OK.
TUNER SET
CUSTOM SET
=AUTO PICTURE
VIDEO STABILIZER
PRESS ( 5,∞), THEN (OK)
PRESS (MENU) TO END
4
5
SELECT MODE
Move the highlight bar
(arrow) to "ON" by pressing
CH 5∞ or SHUTTLE PLUS
%fi.
AUTO PICTURE
=ON
OFF
NOTE:
When using rental tapes, or tapes recorded on other
VCRs, select "ON" or
PRESS ( 5,∞) TO SELECT
PRESS (MENU) TO END
"OFF" as desired to give the best picture.
RETURN TO NORMAL
SCREEN
Press MENU.
1
4
7
2
5
8
0
3
6
9
2 q 5 / 8 6
2
EN
35
Playback
The VCR assesses the quality of the tape once you start playback.
Perform steps 1 and 2 on page 23 ("Simple Playback") before continuing.
1
START PLAYBACK
Press PLAY.
● The VCR adjusts the playback picture quality based on the quality of the tape in use.
AUTO PICTURE
NOTE:
● The Auto Picture screen only appears at the beginning of automatic tracking. Even though the screen doesn't appear after that, the Auto Picture function is operative.
● SUPERIMPOSE must be set to "ON" or the Auto Picture screen will not appear (
Z
pg. 28).
36
EN
1
4
7
2
5
8
0
3
6
9
PLAYBACK AND RECORDING FEATURES (cont.)
Recording
Features
OSD
Record One Program While
Watching Another
1
2
ENGAGE TV MODE
During recording...
● Press TV/VCR. The VCR's VCR indicator goes out. (If you are using the RF connection (
Z
pg. 6) to view the output from your VCR, the TV broadcast being recorded disappears.)
● If you are using the AV connection ( Z pg. 6), to view the output from your VCR, change the TV's input mode from AV to TV.
SELECT CHANNEL FOR
VIEWING
Use the TV’s channel selector to set the channel you want to watch.
C.RESET
TV/VCR
Display Elapsed Recording
Time
1
RESET COUNTER TO ZERO
Before recording starts, press C.RESET. The counter resets to zero and displays the exact elapsed time as the tape runs.
2
DISPLAY ELAPSED TIME ON
SCREEN
During recording, press OSD at any time to see the elapsed time. All indications corresponding to the current status of the VCR are displayed for 5 seconds.
The counter display remains on the screen indicating the elapsed time. Press OSD again to remove the display.
● Make sure "SUPERIMPOSE" is set to "ON" (
● The indications are not be recorded.
Z
pg. 28).
MENU
CH
1
4
7
2
5
8
0
3
6
9
CH
2 q 5 / 8 6
2
OK
SHUTTLE PLUS
EN
37
Stereo And SAP
(Second Audio Program)
Your VCR’s built-in MTS decoder enables reception of Multichannel TV Sound broadcasts.
● The ST indicator on the front display panel lights during stereo broadcast reception, and SAP lights during SAP program reception.
● Both indicators light when a stereo program is accompanied by SAP audio.
To Record Stereo Programs . . .
. . . simply follow the basic recording procedure.
To Listen To Stereo Soundtrack During Recording . . .
. . . select "HI-FI" at the Audio Monitor screen (
Z
pg. 29).
To Record SAP Programs . . .
ACCESS MAIN MENU
SCREEN
Press MENU.
1
2
ACCESS FUNCTION SET
SCREEN
Move the highlight bar (arrow) to "FUNCTION SET" by pressing CH
5∞ or SHUTTLE PLUS %fi, then press OK.
3
ACCESS 2ND AUDIO
SCREEN
Move the highlight bar (arrow) to "2ND AUDIO" by pressing CH
5∞ or SHUTTLE PLUS %fi, then press OK.
4
SELECT MODE
Move the highlight bar
(arrow) to "ON" by pressing CH
5∞ or
SHUTTLE PLUS
%fi.
2ND AUDIO
=ON
OFF
5
PRESS ( 5,∞) TO SELECT
PRESS (MENU) TO END
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary.
NOTES:
● If a SAP program is received, the SAP audio is recorded on both the Normal and Hi-Fi tracks. The main audio program is not recorded.
● If a non-SAP program is received, the main audio is recorded on both the Hi-Fi and Normal audio tracks.
38
EN
VCR Plus+
Timer
Programming
● Before VCR Plus+ Timer programming, see "VCR Plus+
Setup" on page 18.
● Turn on the TV and select the VCR channel 3 or 4 (or AV mode).
NUMBER "8"
1
4
7
CANCEL
2
5
8
0
3
6
9
SP/EP
MENU
2 q 5 8 6
2
NUMBER
NUMBER "9"
OK
TIMER RECORDING
Timer recording allows you to program the VCR to automatically record a program which will be broadcast at some future time.
The timer record function can be programmed using VCR Plus+ or On-Screen Timer Programming. (
Z
pg. 38 or 40)
1
LOAD A CASSETTE
Make sure the record safety tab is present.
● The VCR’s power comes on automatically.
2
3
4
ACCESS VCR PLUS+ SCREEN
Press MENU on the remote control.
VCR PLUS+
● The clock must be set in order to access the VCR
Plus+ screen. If you haven’t set the clock, the
Main Menu screen appears when you press
MENU. Refer to page 7
PRESS NUMBER KEY (0-9)
PRESS (MENU) TO MAIN MENU for the Plug & Play procedure or page 9 for the clock setting procedure.
ENTER PLUSCODE NUMBER
Press the appropriate NUMBER keys to enter the
PlusCode number printed in the TV listings for the TV program you wish to record.
● To make corrections, press CANCEL and input the correct PlusCode number.
● If the PlusCode number you input is incorrect,
"ERROR" may appear on the screen to advise you of the error. This happens when the PlusCode number is for a program which has already passed. "ERROR" is displayed for about 4 seconds and the VCR Plus+ screen reappears (step 2).
CHECK INPUT DATA
Press OK and the Program screen appears.
The PlusCode number you entered appears in the
Program screen. Check to make sure it’s accurate.
PROGRAM 1
(VCR PLUS+ 12345678)
DATE
START
12/24 WED
12:00 PM
STOP
CHANNEL
1:00 PM
40 SP
● To timer-record daily or weekly serials, press
DAILY (NUMBER “8”) or
PRESS (8=DAILY, 9=WEEKLY
SP/EP=REC SPEED)
PRESS (MENU) TO END
WEEKLY (NUMBER “9”). “DAILY” or “WEEKLY” appears on the Program screen. Pressing the button again makes each corresponding display disappear.
● If you made a mistake, press CANCEL and, after pressing MENU as many times as necessary to access the VCR Plus+ screen, input the correct PlusCode number.
SET TAPE SPEED
Press SP/EP.
5
MENU
1
4
7
2
5
8
0
3
6
9
NUMBER
CH
TIMER
OK
SHUTTLE PLUS
EN
39
CHECK/CORRECT INPUT
DATA
6
OK or SHUTTLE PLUS until the item you want to change begins to blink. Then press the appropriate
NUMBER keys, CH
5∞ or SHUTTLE PLUS %fi to obtain the desired setting.
● If you are using a DBS receiver, the BAND indication
(TV or CATV or DBS) appears at right of the channel
7 pressed. See "ATTENTION FOR DBS RECEIVER
USERS" on page 41.
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary.
● Press just once to access the Auto Timer screen
(
Z
pg. 43).
ENGAGE TIMER MODE
Press TIMER. The VCR turns off automatically.
8
NOTES:
● To disengage the timer before recording starts, press TIMER again. Pressing once more re-engages it.
● In case of a power failure after programming, the VCR’s memory backup keeps your selections for approximately
10 minutes.
● When timer-recording cable channels received through a
Cable Box, be sure to keep the Cable Box set to ON.
40
EN
On-Screen
Timer
Programming
Turn on the TV and select the VCR channel 3 or 4 (or AV mode).
MENU
1
4
7
2
5
8
0
3
6
9
NUMBER "8"
CH
CH
2 q 5 8 6
2
NUMBER
NUMBER "9"
OK
SHUTTLE PLUS
EXAMPLE
If you program the VCR to timer record a show on December 24 on channel 40 from 12:00 noon to 1:00 PM in SP mode, the screen will look like this:
DATE
START
STOP
CHANNEL
PROGRAM 1
12/24 WED
12:00 PM
1:00 PM
40 SP
PRESS NUMBER KEY (O–9)
OR ( 5,∞), THEN (OK)
PRESS (MENU) TO END
TIMER RECORDING (cont.)
You can directly program the VCR’s timer to record up to 8 shows, as far as a year in advance. Remember, the clock must be set before you can program the timer (
Z
pg. 7 or 9).
1
2
LOAD A CASSETTE
Make sure the record safety tab is intact. If not, cover the hole with adhesive tape, then load.
● The VCR comes on, and the counter is reset, automatically.
ACCESS ON-SCREEN
MENU
Press MENU as many times as necessary to bring up the
Main Menu screen.
3
ACCESS PROGRAM SET
SCREEN
Make sure the highlight bar (arrow) is on "PROGRAM
SET", then press OK.
4
5
SELECT PROGRAM NUMBER
Press the appropriate
NUMBER keys or CH 5∞ or
SHUTTLE PLUS
%fi to select a vacant program number, then press OK. The first time you set the timer programming function, all the program numbers will
DATE
PROGRAM 1
START
STOP
CHANNEL
– –/– –
– –:– – AM
– –:– – AM
– – SP
PRESS NUMBER KEY (O–9)
OR ( 5,∞), THEN (OK)
PRESS (MENU) TO END be blank; in this case just press OK when the Program Set screen appears.
SET PROGRAM
INFORMATION
Press the appropriate NUMBER keys to set the date, start/stop time and channel number. Press CH 5∞ or
SHUTTLE PLUS
%fi to set AM/PM and tape speed (SP or EP). Press OK after AM/PM, channel number and tape speed settings.
* If you are using a DBS receiver, see "ATTENTION FOR
DBS RECEIVER USERS" on next page.
● Any information comprised of 1 digit (except the channel number) should have a "0" entered before it.
● It is possible to set all information using the CH5∞ or
SHUTTLE PLUS
%fi button.
(In this case, press OK after each setting.) Do not use the CH ∞ or SHUTTLE PLUS fi button to set the date.
● At the Program Set screen, the setting that can be set blinks. When setting of a highlighted item is completed, the highlight bar moves down by 1 line to the next item.
** You can record selected programs at the same time every weekday, or once a week. Before entering the month, press NUMBER key “8” (DAILY) or “9”
(WEEKLY). Either "DAILY" or "WEEKLY" appears.
Press again and "DAILY" or "WEEKLY" disappears.
For weekly recording, the desired date for the day of the week must be entered.
MENU
CH
1
4
7
2
5
8
0
3
6
9
CH
TIMER
2 q 5 8 6
2
6
7
8
EN
41
MAKE CORRECTIONS
To change any of the settings, press OK or SHUTTLE
PLUS until the item you want to change begins blinking. Then set as in step 5.
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary.
● Press just once to access the Auto Timer screen
( Z pg. 43).
ENGAGE TIMER MODE
Press TIMER. The VCR turns off automatically.
NOTES:
● To disengage the timer before recording starts, press TIMER again. Pressing once more re-engages it.
● In case of a power failure after programming, the VCR’s memory backup keeps your selections for approximately 10 minutes.
● If you select "PROGRAM SET" without having set the date and time, an error message appears. Follow its instructions.
● If you enter a start time that has already passed, "ERROR" appears on the screen and blinks.
● Programs that start after midnight must have the next day’s date.
● After timer recording is completed, the VCR’s power goes off automatically.
● You can program the timer while a regular recording is in progress; the on-screen menu will not be recorded.
● If the end of tape is reached during timer recording, the cassette is automatically ejected.
● When timer-recording cable or satellite channels through an external tuner, be sure to keep the cable box or satellite receiver's power ON.
OK
SHUTTLE PLUS
ATTENTION FOR DBS RECEIVER USERS
If you are using a DBS receiver (unless "DBS RECEIVER OUTPUT" is set to "OFF"
Z
pg.21), the BAND indication (TV or CATV or DBS) appears to the right of the channel number display. If the channel
PROGRAM 1 number that has been entered requires that the band be set, the BAND indication starts blinking: DATE 12/24 WED
START 12:00 PM
a- TV : To timer-record a regular TV program received on the VCR.
b- CATV : To timer-record a cable TV program received on the VCR, or through a cable box (unless
"CABLE BOX OUTPUT" is set to "OFF"
Z
pg.16).
c- DBS : To timer-record a satellite program received through a DBS receiver.
STOP
CHANNEL
1:00 PM
110 DBS SP
PRESS NUMBER KEY (O–9)
OR ( 5,∞), THEN (OK)
PRESS (MENU) TO END
Press CH 5∞ or SHUTTLE PLUS %fi to select the appropriate band, then press OK.
● If "BAND" is set to "TV" at the Band screen (
TV will not be displayed.
Z
pg.13), CATV will not be displayed on the Program screen; if it is set to "CATV",
42
EN
MENU
CH
2 q 5 8 6
2
POWER
CANCEL
1
4
7
2
5
8
0
3
6
9
CH
TIMER
OK
SHUTTLE PLUS
TIMER RECORDING (cont.)
Check And Cancel Programs
1
DISENGAGE TIMER
Press TIMER, then press POWER.
ACCESS MAIN MENU
SCREEN
Press MENU as many times as necessary.
2
3
4
ACCESS PROGRAM SET
SCREEN
Press CH
5∞ or SHUTTLE PLUS %fi to move the highlight bar (arrow) to "PROGRAM SET", then press
OK.
CHECK PROGRAM
INFORMATION
Press CH
5∞ or SHUTTLE PLUS %fi to check the programs in succession.
To Cancel A Program . . .
5
CANCEL A PROGRAM
Press CANCEL.
● Repeat steps 4 and 5 as many times as necessary.
6
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary. If there are still programs remaining, go to step 7.
RE-ENGAGE TIMER
Press TIMER again.
7
MENU
CH
2 q 5 / 8 6
2
1
4
7
2
5
8
0
3
6
9
CH
TIMER
OK
SHUTTLE PLUS
EN
43
Auto Timer
When the Auto Timer is set to ON the timer is automatically engaged when the VCR's power is turned off and automatically disengaged when the VCR is powered back on.
ACCESS MAIN MENU
SCREEN
Press MENU as many times as necessary.
1
2
ACCESS FUNCTION SET
SCREEN
Move the highlight bar (arrow) to "FUNCTION SET" by pressing CH
5∞ or SHUTTLE PLUS %fi, then press OK.
3
ACCESS AUTO TIMER
SCREEN
Move the highlight bar (arrow) to "AUTO TIMER" by pressing CH
5∞ or SHUTTLE PLUS %fi, then press OK.
Now skip to step 2 of the procedure below.
Or, during on-screen timer programming ...
1
2
ACCESS AUTO TIMER
SCREEN
In step 7 in the VCR Plus+ Timer Programming ( Z pg. 38) or On-Screen Timer Programming procedure (
Z
pg. 40), press MENU.
SELECT MODE
Move the highlight bar
(arrow) to your choice
("ON" or "OFF") by pressing CH
5∞ or
SHUTTLE PLUS
%fi.
AUTO TIMER
ON
=OFF
PRESS ( 5,∞) TO SELECT
PRESS (MENU) TO END
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary.
3
NOTE:
For safety, when AUTO TIMER is set to “OFF”, all other VCR functions are disabled while the Timer mode is engaged. To disengage the timer, press TIMER.
44
EN
Instant Timer
Recording
(ITR)
V C R
SP
2 q 5 8 6
2
R E C
TIMER RECORDING (cont.)
This easy method lets you record for from 30 minutes to 6 hours
(selectable in 30-min. increments), and shuts the VCR off after recording is finished.
START RECORDING
Press REC on the front panel.
1
2
ENGAGE ITR MODE
Press REC again. REC blinks and 0:30 appears on the front display panel.
3
SET RECORDING
DURATION
If you want to record for more than 30 minutes, press
REC to extend the time. Each press extends recording time by 30 minutes.
NOTES:
● You can only perform ITR using the REC button on the VCR's front panel.
● After you set the ITR time, the previous display reappears.
● To check the remaining time, press REC once during recording and the remaining time will be displayed for about 5 seconds. Be careful not to press REC again within these 5 seconds, or you will round the recording time up to the next
30 minute increment.
EDITING
Edit To Or
From Another
VCR
AUDIO OUT
Player Your VCR
VIDEO IN
Recorder
1
4
7
2
5
8
0
3
6
9
VIDEO
OUT
Audio/Video cable
(not supplied)
AUDIO IN
Another VCR
You can use your VCR as the player or the recorder.
EN
45
1
2
MAKE CONNECTIONS
Connect an AV cable between the player’s VIDEO OUT and AUDIO OUT connectors and the recorder’s VIDEO
IN and AUDIO IN connectors.
● When using your VCR as the recorder and a monaural
VCR as the player, connect the player’s AUDIO OUT connector to the AUDIO IN L connector on the recorder.
LOAD CASSETTES
Insert the playback cassette into the player and the cassette to be recorded on into the recorder.
3
SET RECORDER’S INPUT
MODE
Set to AUX. With this VCR, press NUMBER key “0” (AU appears on the front display panel in place of a channel number).
NOTE:
When using this VCR as the recorder, make sure to select
"FRONT" or "REAR" (depending on which input connectors you use) at the Aux Input Screen. (To select the correct AUX input connector, follow steps 4, 5, 9 – 11 from the "Edit
From A Camcorder" section, Z pg. 46.)
START PLAYER
Set to its play mode.
4
NOTE:
If the player is equipped with a superimpose/OSD disable feature then set "SUPERIMPOSE" to OFF before pressing PLAY ( Z pg. 28).
START RECORDER
Set to its record mode.
5
NOTE:
If you use a cable box or a DBS receiver connected to one of the VCR's auxiliary input connectors and if you have used this
VCR as the recording deck for editing, be sure to select again the required input at the AUX Input screen when you finish editing.
NUMBER "0"
46
EN
Edit From A
Camcorder
AUDIO IN Recorder Your VCR
VIDEO
IN
2 q / 8 6
2
To rear panel PAUSE/
AV COMPU LINK connector
Mini-plug cable (not supplied)
(JVC camcorder only)
Audio/Video cable
(not supplied)
VIDEO
OUT
Camcorder
AUDIO OUT
EDIT
Player
NUMBER "0"
1
4
7
2
5
8
0
3
6
9
CH
MENU
OK
SHUTTLE PLUS
EDITING (cont.)
You can use a camcorder as the player and your VCR as the recorder.
1
MAKE CONNECTIONS
Connect an AV cable between the camcorder’s VIDEO
OUT and AUDIO OUT connectors and your VCR’s
VIDEO IN and AUDIO IN connectors.
● When a Master Edit Control-equipped JVC camcorder is used, the camcorder is capable of controlling your VCR.
The mini-plug cable is a mono 3.5 mm mini-plug to mono 3.5 mm mini-plug connector.
● If connecting to a camcorder with a monaural output, connect the audio output connector on the camcorder to AUDIO IN L of the VCR.
LOAD A CASSETTE
Insert the cassette to be recorded on into the recorder.
2
SET RECORDER’S INPUT
MODE
Press NUMBER key “0” to set to AUX.
3
ACCESS MAIN MENU
SCREEN
Press MENU as many times as necessary.
4
5
ACCESS FUNCTION SET
SCREEN
Press CH
5∞ or SHUTTLE PLUS %fi to move the highlight bar (arrow) to “FUNCTION SET”, then press
OK.
6
7
If you’re using a JVC Master Edit Control-equipped camcorder — step 6
If not — step 9
ACCESS SPECIAL
FUNCTION SCREEN
Press CH 5∞ or SHUTTLE PLUS %fi to move the highlight bar (arrow) to “SPECIAL FUNCTION”, then press OK.
SELECT MODE
Press CH
5∞ or SHUTTLE
PLUS %fi to move the highlight bar (arrow) to
“PAUSE”.
SPECIAL FUNCTION
=PAUSE
AV COMPU-LINK
PRESS ( 5,∞) TO SELECT
PRESS (MENU) TO END
MENU
CH
1
4
7
2
5
8
0
3
6
9
CH
2 q 5 / 8 6
2
OK
SHUTTLE PLUS
EN
47
RETURN TO FUNCTION
SET SCREEN
Press MENU.
8
9
10
11
SELECT INPUT
If you are connecting the
AV cable to the AV connectors on the front of the VCR, move the
AUX INPUT
= FRONT
REAR highlight bar (arrow) to
"FRONT" by pressing
CH
5∞ or SHUTTLE PLUS
%fi. If you are connecting the AV cable to the AV
PRESS ( 5,∞) TO SELECT
PRESS (MENU) TO END connectors on the back of the VCR, move the highlight bar (arrow) to "REAR" by pressing CH
5∞ or SHUTTLE
PLUS
%fi.
RETURN TO NORMAL
SCREEN
Press MENU as many times as necessary.
START PLAYER
Set the camcorder to its play mode.
12
ACCESS AUX INPUT
SCREEN
Press CH
5∞ or SHUTTLE PLUS %fi to move the highlight bar (arrow) to “AUX INPUT”, then press OK.
13
NOTE:
If the camcorder is equipped with a superimpose/OSD disable feature then set its superimpose or display feature to OFF before pressing play.
START RECORDER
Set your VCR to its record mode.
● If you are using a Master Edit Control-equipped JVC camcorder, it can put the recorder automatically into
Record mode. (Refer to camcorder's instruction manual.)
NOTE:
If you use a cable box or a DBS receiver connected to one of the VCR's auxiliary input connectors, be sure to select again the required input at the AUX Input screen when you finish editing.
48
EN
(Ex.) To set remote control to RCA 05:
POWER
0 5
STOP
Hold down
Press in succession
POWER
NUMBER
VOL. +/–
1
4
7
2
5
8
0
3
6
9
CH
ENTER
TV/CABLE/DBS/VCR
TV/VCR
Release
SPECIAL FEATURES
TV Multi-Brand Remote
Control
The VCR's remote control can control several functions on JVC remote control TVs and on the brands of remote control TVs listed below.
The TV brand code is factory preset to control JVC TVs.
TURN ON THE TV
Turn the power on using the TV's remote control.
1
2
SET REMOTE CONTROL
MODE
Set the TV/CABLE/DBS/VCR switch on the VCR's remote control to TV.
3
SET TV BRAND CODE
Refer to the chart below. While holding down POWER on the VCR's remote control, enter your TV’s brand code using the NUMBER keys, then press STOP.
Follow the example shown at bottom left.
● Once you have set the remote control to operate the
TV, you don’t have to repeat this step until you replace your remote control’s batteries.
● PANASONIC has two codes. If the TV does not function with one code, try entering the other.
4
OPERATE TV
First, press POWER on the remote to see if the TV’s power goes off as it should. If it does, try other operations.
● The POWER, TV/VCR, CH5∞, VOL +/– and
NUMBER keys on the remote can all be used to operate the TV. *For some brands of TV, you must press ENTER after having pressed the NUMBER keys.
● To return the remote to VCR control, set the TV/
CABLE/DBS/VCR switch to VCR.
NOTE:
Depending on the kind of TV, there may be cases where some or all functions cannot be operated using the remote control.
TV BRAND NAME
JVC
MAGNAVOX
MITSUBISHI
PANASONIC
RCA
SHARP
SONY
TOSHIBA
ZENITH
HITACHI
SAMSUNG
SANYO
SEARS
12
13
13
07
08
09
10
BRAND CODE
01
02
03
04, 11
05
06
NUMBER
1
4
7
2
5
8
0
3
6
9
CH
POWER
ENTER
TV/CABLE/DBS/VCR
CABLE BOX BRAND NAME BRAND CODE
CURTIS
GEMINI
GENERAL INSTRUMENTS
09, 10
08
01, 02, 03, 04, 05, 06, 07, 08
HAMLIN
JERROLD
OAK
PIONEER
15, 16, 17, 18
01, 02, 03, 04, 05, 06, 07, 08
19, 20, 21
13, 14
REGAL
SAMSUNG
SCIENTIFIC ATLANTA
SIGMA
SL MARX
TELEVIEW
VIDEOWAY
ZENITH
15, 16, 17, 18
08, 13
09, 10
19, 20, 21
08, 13
08, 13
11, 12
11, 12
EN
49
Cable Box Multi-Brand
Remote Control
The VCR's remote control can control functions on the brands of cable boxes listed below. Some cable box brands have more than one code. If your cable box does not function with a specified code, try other codes.
TURN ON THE CABLE BOX
Turn the power on using the cable box’s remote control.
1
2
SET REMOTE CONTROL
MODE
Set the TV/CABLE/DBS/VCR switch on the VCR’s remote control to CABLE/DBS.
3
4
ENTER CABLE BOX BRAND
While holding down POWER on the VCR's remote control, use the NUMBER keys to enter the cable box brand number from the chart at bottom left and then press STOP.
Follow the example shown below.
● Once you have set the remote control to operate the cable box, you don't have to repeat this step until you replace the remote control's batteries.
OPERATE CABLE BOX
First, press POWER to see if the cable box’s power goes off as it should. If it does, try other functions (CH
5∞ and the NUMBER keys can be used to operate the cable box).
● For some brands of cable box, you must press ENTER after having pressed the NUMBER keys.
● To return the remote to VCR control, set the TV/
CABLE/DBS/VCR switch to VCR.
NOTES:
● You must set the cable box brand for your remote control and the cable box brand for your Controller (
Z
pg. 17) separately.
The list of cable box brands that can be controlled by your remote control is different from the list of brands that can be controlled by your controller.
● It is possible that the remote control will not operate your cable box even if the cable box’s channels automatically change during timer recording using the Controller.
● It's not possible to set the remote control for both your cable box and your DBS receiver at the same time; you can only set the remote control to the brand of either one.
(Ex.) To set remote control to OAK 19:
POWER
1 9
STOP
Hold down
Press in succession
Release
50
EN
NUMBER
1
4
7
2
5
8
0
3
6
9
ENTER
CH
(Ex.) To set remote control to RCA 80:
POWER
8 0
STOP
POWER
TV/CABLE/DBS/VCR
Release
SPECIAL FEATURES (cont.)
DBS Receiver Multi-Brand
Remote Control
The VCR's remote control can control functions on the brands of DBS (Direct Broadcast Satellite) receivers listed below.
1
TURN ON THE DBS
RECEIVER
Turn the power on using the DBS receiver’s remote control.
2
SET REMOTE CONTROL
MODE
Set the TV/CABLE/DBS/VCR switch on the VCR’s remote control to CABLE/DBS.
3
4
ENTER DBS RECEIVER BRAND
While holding down POWER on the VCR's remote control, use the NUMBER keys to enter the DBS receiver brand number from the chart below and then press STOP.
Follow the example shown at bottom left.
● Once you have set the remote control to operate the
DBS receiver, you don't have to repeat this step until you replace the remote control's batteries.
OPERATE DBS RECEIVER
First, press POWER to see if the DBS receiver’s power goes off as it should. If it does, try other functions
(CH
5∞ and the NUMBER keys can be used to operate the DBS receiver).
● For some brands of DBS receiver, you must press
ENTER after having pressed the NUMBER keys.
● To return the remote to VCR control, set the TV/
CABLE/DBS/VCR switch to VCR.
NOTES:
● You must set the DBS receiver brand for your remote control and the DBS receiver brand for your Controller (
Z
pg. 22) separately.
● It is possible that the remote control will not operate your DBS receiver even if the DBS receiver’s channels automatically change during timer recording using the Controller.
● Though ECHOSTAR has a number of different remote codes, this remote control is applicable only to one of those codes preset at the factory.
● It's not possible to set the remote control for both your cable box and your DBS receiver at the same time; you can only set the remote control to the brand of either one.
DBS BRAND NAME
RCA (DSS)
SONY (DSS)
PRIMESTAR
ECHOSTAR
BRAND CODE
80
81
90
91
Hold down
Press in succession
A/B CODE
POWER
1
4
7
2
5
8
0
3
6
9
TIMER
EN
51
Control Two JVC VCRs
The supplied remote control is capable of controlling two JVC
VCRs independently using the A/B CODE switch. You can set this
VCR so it responds to remote commands only when the switch is set to B, and another VCR so it responds to commands when the switch is set to A. The switch is preset to A because this VCR normally responds to A-code signals. Follow steps 1 – 4 to set this
VCR to respond to B-code commands.
UNPLUG VCR'S POWER
CORD
Unplug from the AC outlet.
1
SET A/B CODE SWITCH
Set the A/B CODE switch on the remote control to B.
2
PLUG IN POWER CORD
Plug back in to the AC outlet.
3
TURN VCR POWER ON
Press POWER on the remote.
4
The VCR will now respond only to B-code commands.
To set the VCR back to respond to A code signals, repeat the same procedure as shown above except setting the A/B CODE switch to A instead of B in step 2.
You can control two VCRs with the same remote control by switching the remote's code between A and B.
52
EN
TROUBLESHOOTING
Before requesting service for a problem, use this chart and see if you can repair the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your VCR off for repair.
POWER
SYMPTOM
1. The power won’t come on.
2. The clock works, but the VCR’s power won’t come on.
3. The remote control won’t function.
TAPE TRANSPORT
SYMPTOM
1. The cassette gets stuck partway during loading, and is ejected.
2. The tape stops during rewind or fast forward.
POSSIBLE CAUSE
● The power cord is disconnected.
● The TIMER mode is engaged with
Auto Timer set to "OFF" (
Z
pg. 43).
● The batteries are discharged.
POSSIBLE CAUSE
● The cassette was inserted incorrectly.
● The Counter Memory indicator (“M”) is lit on the front display panel.
CORRECTIVE ACTION
Connect the power cord.
Press TIMER to disengage.
Replace the dead batteries with new ones.
CORRECTIVE ACTION
Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is pointing towards the VCR. Then insert the cassette.
Press C.MEMORY to disengage the
Counter Memory mode and extinguish the indicator.
PLAYBACK
SYMPTOM
1. The tape is running but the picture won’t appear.
2. Noise appears during visual search.
3. Breaks are noticeable in Hi-Fi soundtrack.
4. The playback picture is blurred or interrupted, even though TV broadcasts are clear.
5. The Hi-Fi soundtrack cannot be heard.
RECORDING
SYMPTOM
1. Recording won’t start.
POSSIBLE CAUSE
● If you’re using the RF OUT connection ( Z pg. 6), the channel selector on the TV is set incorrectly.
● If you’re using the AV connection
(
Z
pg. 6), the TV receiver is set to the wrong mode.
● This is normal.
● Automatic tracking is engaged.
● The video heads may be dirty.
● The AUDIO MONITOR option at the
Function Set screen was set incorrectly.
POSSIBLE CAUSE
● There’s no cassette loaded.
● The loaded cassette has had its record safety tab removed.
CORRECTIVE ACTION
Set the channel selector to channel 3 or 4.
Set the TV receiver to its AV mode.
(
Engage and adjust tracking manually
Z
pg. 26).
The heads must be cleaned. Consult your JVC dealer.
(
Set AUDIO MONITOR to "HI-FI"
Z
pg. 29).
2. TV broadcasts won’t record properly.
3. Tape-to-tape editing won’t work.
● The VCR has been set to its AUX mode by mistake.
●The VCRs or the camcorder and the
VCR have been incorrectly connected.
● The power to one or more of the units has not been turned on.
● The recorder’s input mode has been set incorrectly.
CORRECTIVE ACTION
Insert a cassette.
Remove the cassette and cover the hole with adhesive tape, or load a cassette on which the record safety tab is intact.
Set the VCR to the appropriate channel.
Refer to the directions and the illustration
( under “Edit To Or From Another VCR”
Z
pg. 45) or “Edit From A Camcorder”
(
Z
pg. 46) and properly connect the units.
Make sure the power to all units is on.
Set the recorder’s input mode to AUX and select "FRONT" or "REAR" at the
Aux Input Screen (
Z
pg. 47).
EN
53
TIMER RECORDING
SYMPTOM
1. Timer recording won’t work.
POSSIBLE CAUSE
● The clock and/or the timer have been set incorrectly.
● The timer is not engaged.
● The VCR has not been set up properly.
2. On-screen timer programming won’t work.
3. TIMER and ] on the front display panel won’t stop blinking.
4. The cassette is automatically ejected, and TIMER and ] on the front display panel won’t stop blinking.
5. TIMER blinks for 10 seconds and the timer mode is disengaged.
8. Satellite channels are not automatically switched during timer recording.
9. Timer recording begins as scheduled, but the channel is always incorrect.
10.We moved, and now VCR Plus+ doesn’t work properly.
11. “PROGRAM FULL” is displayed on the VCR Plus+ screen.
● Timer recording is in progress.
● The timer is engaged but there’s no cassette loaded.
● The loaded cassette has had its record safety tab removed.
6. The cassette is automatically ejected, the power shuts off and
TIMER and ] won’t stop blinking.
7. Cable channels are not automatically switched during timer recording.
● TIMER has been pressed when there are no programs in memory, or the timer record program information has not been programmed correctly.
● The end of tape was reached during timer recording.
● The Controller is not properly connected to the VCR.
● The output channel selected in the
Cable Box Output screen is incorrect.
● The cable box’s power is off.
● The Controller is not properly connected to the VCR.
● The output channel selected in the
DBS Receiver Output screen is incorrect.
● The DBS receiver’s power is off.
● Even though you don't use an external Cable Box, "CABLE BOX
OUTPUT" is set to "ON".
● The receivable stations in the new area are received on different channels than those in the previous area.
● All 8 programs of the VCR’s timer memory are used.
CORRECTIVE ACTION
Set the clock and/or timer correctly.
Press TIMER and check to make sure that TIMER appears on the front display panel.
Re-perform the set-up procedures.
Make sure you have compensated for
Guide Channel and VCR or cable
( box channel number mismatches
Z
pg. 18).
Timer programming can’t be performed when timer recording is in progress.
Wait until it finishes.
Load a cassette with the record safety tab intact, or with the hole covered with adhesive tape.
Remove the cassette and cover its hole with adhesive tape, or replace it with a cassette on which the safety tab is intact.
Check the programmed data and reprogram as necessary, then press
TIMER again.
The program may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire program.
(
Connect the Controller correctly
Z
pg. 15).
After confirming your cable box’s output channel number, re-access the
Cable Box Output screen and select the correct number (
Z
pg. 16).
Make sure the power is on before timer recording starts.
(
Connect the Controller correctly
Z
pg. 20).
After confirming your DBS receiver’s output channel number, re-access the
DBS Receiver Output screen and select the correct number (
Z
pg. 21).
Make sure the power is on before timer recording starts.
(
Set "CABLE BOX OUTPUT" to "OFF"
Z
pg. 16).
Re-perform the VCR Plus+ setup procedure (
Z
pg. 18).
Wait until a space in memory clears, or cancel unnecessary program information (
Z
pg. 42).
54
EN
OTHER PROBLEMS
SYMPTOM
1. When scanning channels, some of them are skipped over.
2. The channel can’t be changed.
TROUBLESHOOTING (cont.)
POSSIBLE CAUSE
● Those channels have been preset to be skipped.
● Recording is in progress.
3. The remote control won’t operate my TV or cable box or DBS receiver.
4. Even though Auto or Semi-Auto clock setting has been selected, the clock is incorrect.
● The remote control brand setting is incorrect.
● The clock setting data received from the Host Channel is incorrect.
CORRECTIVE ACTION
If you need the skipped channels, restore them (
Z
pg. 14).
Press PAUSE to pause the recording, change channels, then press PLAY to resume recording.
Re-set the remote control to the correct brand (
Z
pg. 48 or 49 or 50).
Select a different Host Channel during
( the Semi-Auto setting procedure
Z
pg. 10), or perform the Manual setting procedure (
Z
pg. 11).
ATTENTION:
This VCR contains microcomputers. External electronic noise or interference can cause microcomputer to malfunction. If the
VCR does not operate correctly switch its power off and unplug the power cord from the AC supply. Wait for a while and then plug the power back in. Eject and check the condition of the cassette. If everything appears normal resume operating the VCR as usual.
QUESTIONS AND ANSWERS
PLAYBACK
Q. What happens if the end of the tape is reached during playback or search?
A. The tape is automatically rewound to the beginning.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Q. Can the VCR indefinitely remain in the still mode?
A. No. It stops automatically after 5 minutes to protect the heads.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Q. During search, slow, still and frame-by-frame playback, I can’t hear any audio. What’s the problem?
A. This is normal.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Q. During search, still and frame-by-frame playback, the picture is intermittent. What’s the cause?
A. Picture loss occurs when these types of playback are attempted with a tape recorded in LP mode. Pressing
PLAY to return to normal playback will restore the picture.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Q. When returning from multi-speed search to normal playback, the picture is disturbed. Should I be concerned about this?
A. No, it is normal.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Q. Noise bars appear during multi-speed search. What’s the problem?
A. This is normal.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Q. When playing back programs that have been timerrecorded with consecutive times (such one program from 8:00 to 9:00 and another one from 9:00 to
10:00), the picture becomes momentarily distorted at the point where the first program ends and the second program begins. Is this a malfunction?
A. No. This is normal.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Q. Other than preventing further recording, what effect does removing the safety tab have?
A. It disables marking of index codes.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Q. Sometimes, during Index Search, the VCR can’t find the program I want to see. Why not?
A. There may be index codes too close together.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Q. During playback, on-screen operational indicators sometimes jitter. Why does this happen?
A. If the condition of the tape being played back is not good, jittering of the video (including on-screen indicators) may occur.
EN
55
RECORDING
Q. When I pause and then resume a recording, the end of the recording before the pause is overlapped by the new recording. Why does this happen?
A. This is normal. It reduces distortion at the pause and resume points.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Q. Can the VCR indefinitely remain in the Record-Pause mode?
A. No. The VCR automatically goes to its Stop mode after 5 minutes to protect the heads. When paused during Instant Timer Recording (ITR), the VCR shuts off automatically after 5 minutes.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Q. What happens if the tape runs out during recording?
A. The VCR automatically rewinds it to the beginning.
TIMER RECORDING
Q. REC and TIMER remain lit on the front display panel.
Is there a problem?
A. No. This is a normal condition for a timer recording in progress.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Q. Can I program the timer while I’m watching a tape or a TV broadcast?
A. Yes, but while you are setting the timer you won't see the tape's or broadcast program's picture as it is replaced by the on-screen menu. The audio from the tape or broadcast program will be present during the setting of the timer.
56
EN
List Of Terms
This guide serves as a quick way to locate frequently used terms and on-screen display names.
A
A/B Code ....................................................................51
Add Channel ...............................................................14
AFC .............................................................................14
Audio Monitor ............................................................29
Auto Channel Setting ..................................................12
Auto Clock Setting ...................................................... 11
Auto Daylight Saving Time .......................................... 11
Auto Picture ................................................................34
Auto Timer ..................................................................43
Automatic Tracking .....................................................26
Aux Input ....................................................................46
AV Compu Link Playback ........................................... 32
AV Connection .............................................................6
B
Band ...........................................................................13
C
Cable Box ...................................................................15
Cable Box Brand Setting ..............................................17
Cable Box Controller ...................................................15
Cancel Program ..........................................................42
Cassette Adapter.................................... ...................... 23
Check Program ...........................................................42
Connection to TV ..........................................................6
Contents ........................................................................5
Counter Memory .........................................................31
Counter Reset ..............................................................31
D
DBS Receiver ..............................................................20
DBS Receiver Brand Setting ........................................22
DBS Receiver Controller .............................................20
Delete Channel ...........................................................14
E
Editing .........................................................................45
F
Frame-by-Frame Playback ...........................................25
Function Setting ..........................................................28
G
Guide Channel Map ....................................................19
Guide Channel Setting ................................................19
H
Host Channel Selection ...............................................10
I
Index Search ...............................................................30
Insert Cassette .............................................................23
Instant ReView ............................................................30
ITR (Instant Timer Recording) ...................................... 44
L
Language Selection .......................................................8
INDEX
M
Main Menu ...................................................................8
Manual Channel Setting ..............................................14
Manual Clock Setting .................................................. 11
Manual Tracking .........................................................26
MBR (Multi-Brand Remote) Code Setting ..................... 48
N
Next-Function Memory ...............................................31
O
On-Screen Display ......................................................28
On-Screen Timer Programming ................................... 40
On-Screen Timer Recording ........................................40
Override Auto Clock Setting ..........................................9
P
PBS Channel .................................................................7
Playback .....................................................................23
Plug & Play ...................................................................7
R
Record Safety Tab .......................................................24
Recording ...................................................................24
Repeat Playback ..........................................................31
Reverse Motion Playback ............................................25
Reverse Slow Motion Playback ................................... 25
RF Connection ..............................................................6
S
SAP (Second Audio Program) ...................................... 37
Second Audio .............................................................37
Select Cable Box Output Channel ............................... 16
Select DBS Receiver Output Channel .......................... 21
Semi-Auto Clock Setting ..............................................10
Skip Search .................................................................30
Slow Motion Playback ................................................25
Specifications ..............................................................60
Still Picture Playback ...................................................25
Superimpose ...............................................................28
T
Tape Position Indicator ................................................26
Tape Speed Setting ......................................................24
Time Zone Selection ................................................... 11
Tuner Setting ...............................................................12
V
Variable-Speed Search ................................................25
VCR Plus+ ...................................................................18
VCR Pius+ Timer Programming ................................... 38
VCR Pius+ Timer Recording ........................................38
Video Stabilizer ...........................................................27
FRONT VIEW
1 2 3 4 5
POWER
VIDEO (MONO)L – AUDIO – R
MENU
SP
V C R
TIMER
AM
PM
H M S
ST
SAP
M
R E C
PLAY
PAUSE
CH
REW
2
PLAY
FF
2
OK
REC q
STOP/EJECT
5 / 8
PAUSE
6
6 7 8
1 Power On/Off Button (
2 Cassette Loading Slot
3 Rewind [REW] Button (
Z
pg. 8)
Z
pg. 23)
Z
pg. 23)
4 PLAY Button (
5 Fast-Forward [FF] Button (
Z
pg. 8)
8 Instant REVIEW Button (
Z
pg. 23)
6 VIDEO/AUDIO Input Connectors (
7 MENU Button (
Z
pg. 30)
Z
pg. 46)
9 0 !
@ # $ %
9 Front Display Panel (
Z
pg. 58)
0 Remote Control Sensor
! Channel [CH] 5∞ Button (
@ OK Button (
Z
pg. 8)
# Record [REC] Button (
Z
pg. 24)
$ STOP/EJECT Button (
% PAUSE Button (
Z
Z
pg. 24)
Z
pg. 23)
pg. 25)
EN
57
58
EN
REAR VIEW
1
INDEX (cont.)
2 3 4 5
CABLE
BOX
PAUSE/
AV
COMPU
-LINK
AUDIO
IN
R
OUT ANT. IN
L
RF OUT
VIDEO
CH3 CH4
6
1 Power Cord (
Z
pg. 6)
2 PAUSE/AV COMPU-LINK Connector
● Remote PAUSE Connector (
Z
● AV COMPU-LINK Connector (
pg. 46)
Z
3 VIDEO/AUDIO Input Connectors (
pg. 32)
Z
pg. 45)
7 8
4 VIDEO/AUDIO Output Connectors (
Z
pg. 45)
5 ANT. IN Connector (
6 CABLE BOX Connector (
7 Channel 3/4 Switch (
8 RF OUT Connector (
Z
pg. 6)
Z
pg. 15, 20)
Z
pg. 6)
Z
pg. 6)
FRONT DISPLAY PANEL
1 2 3 4 5 6 7
SP
V C R
TIMER
AM
PM
H
8 9 0
1 VCR Mode Indicator (
Z
2 Tape Speed Indicators (
pg. 36)
Z
pg. 24)
3 AM/PM Indicators (
4 Clock Display (
Z
pg. 7)
Z
pg. 7)
5 Multi-Channel TV Sound Indicators (
6 Recording Mode Indicator
Z
pg. 37)
Instant Timer Recording Indicator (
Z
pg. 44)
M S
ST
SAP
M
R E C
PLAY
PAUSE
!
@
7 Play Mode Indicator
8 “Cassette Loaded” Mark
9 Timer Mode Indicator
0 Channel Display [“AU” for AUX mode]
Counter Display (
Z
pg. 23)
! Counter Memory Mark (
Z
pg. 31)
@ Pause Mode Indicator
EN
59
1
2
3
4
5
6
7
8
9
0
!
@
#
REMOTE CONTROL (Provided)
POWER
A B
1
4
7
C.RESET
CANCEL
CH SKIP
2
5
DAILY (M–F)
8
AUX
0
ENTER
OSD
3
6
WEEKLY
9
TIMER
TV
VOL.
CH
CABLE DBS
SP/EP DISPLAY TV/VCR
(VIDEO)
PLAY
REW
TV
FF
VCR
REC
C.M
EMOR
Y
ADD
MEN
U
STOP
PAUSE
SKIP SEAR
CH
OK
SHUTTLE
PLUS
MULTI BRAND
REMOTE CONTROL UNIT
&
*
(
) q w e r t y u
$
%
^
1 Instant REVIEW Button (
Z
pg. 30)
2 A/B Code Select Switch (
3 NUMBER Buttons (
Z
Z
pg. 51)
pg. 24)
4 “AUX” Mode Select Button (
5 CANCEL Button (
Z
pg. 46)
Z
pg. 42)
Counter [C.] RESET Button (
Channel [CH.] SKIP Button (
6 Volume [VOL] +/– Buttons (
7 DISPLAY Button (
Z
pg. 31)
Z
pg. 31)
Z
pg. 14)
Z
pg. 48)
8 Recording Speed [SP/EP] Button (
9 Rewind [REW] Button (
Z
pg. 23)
Z
pg. 24)
0 PLAY Button (
Z
pg. 23)
! Record [REC] Button (
Z
pg. 24)
@ Counter [C.] MEMORY Button (
ADD Button (
Z
pg. 14)
Z
pg. 8)
Z
pg. 31)
# MENU Button (
$ POWER ON/OFF Button (
Z
pg. 24)
Z
pg. 8)
% ENTER Button (
On-Screen Display [OSD] Button (
Z
pg. 28)
Z
pg. 38) ^ DAILY Timer Recording Button (
& WEEKLY Timer Recording Button (
* TIMER Button (
Z
) TV/VCR Button (
pg. 39)
( Channel [CH] 5∞ Buttons (
Z
pg. 36) q TV/CABLE/DBS/VCR Switch ( w Fast-Forward [FF] Button ( e PAUSE Button (
Z
Z
pg. 38)
pg. 24)
Z
pg. 48)
Z
pg. 23) r STOP Button (
Z
Z
pg. 25)
Z
pg. 23) t SKIP SEARCH Button (
pg. 8)
Z
pg. 30) y OK Button ( u SHUTTLE PLUS Button (
Z
pg. 8)
Installing Batteries
1 Open the battery compartment cover.
2 Insert 2 "AA"-size batteries (provided) in the direction indicated under the battery cover.
3 Replace the cover.
How To Use
The remote control can operate most of your VCR's functions.
1 Point the remote control toward the sensor window.
2 Press the appropriate operation button.
3 The maximum operating distance of the remote control is about 8 m.
NOTES:
● This remote control can also operate various brands of
TVs, Cable Boxes and DBS Receivers. For instructions,
Z pg. 48 – 50.
● If the remote control doesn't work properly, remove its batteries, wait a short time, replace the batteries and then try again.
60
EN
GENERAL
Power requirement
Power consumption
: AC 120 V` , 60 Hz
: 21 W
Temperature
Operating
Storage
Operating position
: 5°C to 40°C (41°F to 104°F)
: –20°C to 60°C (–4°F to140°F)
: Horizontal only
Dimensions (W x H x D) : 400 x 94 x 273 mm
Weight
Format
Maximum recording time
SP
(15-3/4" x 3-3/4" x 10 -3/4")
: 3.3 kg (7.3 lbs)
: VHS NTSC standard
EP
: 210 min. with ST-210 video cassette
: 630 min. with ST-210 video cassette
VIDEO/AUDIO
Signal system
Recording/
Playback system
Signal-to-noise ratio
Horizontal resolution
Frequency range
Normal audio
Hi-Fi audio
Input/Output
: NTSC-type color signal and
EIA monochrome signal, 525 lines/60 fields
: DA-4 (Double Azimuth) head helical scan system
: 45 dB
: 240 lines
: 70 Hz to 10,000 Hz
: 20 Hz to 20,000 Hz
: RCA connectors (IN x 2,
OUT x 1)
TUNER
Tuning system
Channel coverage
VHF
UHF
CATV
RF output
: Frequency-synthesized tuner
: Channels 2–13
: Channels 14–69
: 113 Channels
: Channel 3 or 4 (switchable; preset to Channel 3 when shipped) 75 ohms, unbalanced
SPECIFICATIONS
TIMER
Clock reference
Program capacity
: Quartz
: 1-year programmable timer/
8 programs
Memory backup time : Approx. 10 min.
ACCESSORIES
Provided accessories : RF cable (F-type),
Infrared remote control unit,
“AA” battery x 2
Specifications shown are for SP mode unless otherwise specified.
E. & O.E. Design and specifications subject to change without notice.
FOR SERVICING (Only in U.S.A.)
HOW TO LOCATE YOUR JVC SERVICE CENTER
EN
61
TOLL FREE: 1-800-252-5722
Dear customer:
In order to receive the most satisfaction from your purchase, read the instruction booklet before operating the unit. In the event that repair is necessary, or for the address nearest your location, please refer to the factory service center list below or within the
Continental United States, call 1-800-252-5722 for your authorized servicer. Remember to retain your Bill of Sale for Warranty
Service.
— JVC
107 Little Falls Road
Fairfield, NJ 07004-2105
(201) 808-9279
5665 Corporate Avenue
Cypress, CA 90630-4727
(714) 229-8011
230 Eliot Street
Ashland, MA 01721-2377
(508) 881-5923
JVC SERVICE & ENGINEERING
COMPANY OF AMERICA
DIVISION OF US JVC CORP.
FACTORY SERVICE CENTER LOCATIONS
1500 Lakes Parkway
Lawrenceville, GA 30243-5857
(770) 339-2522
10700 Hammerly Boulevard, Suite 110
Houston, TX 77043-2310
(713) 935-9331
8192 W State Road 84
Davie, FL 33324-4611
(954) 472-1960
705 Enterprise Street
Aurora, IL 60504-8135
(630) 851-7855
2969 Mapunapuna Place, Suite 101
Honolulu, HI 96819-2000
(808) 833-5828
890 Dubuque Avenue
South San Francisco, CA 94080-1804
(415) 871-2666
Sophisticated electronic products may require occasional service. Just as quality is a keyword in the engineering and production of the wide array of JVC products, service is the key to maintaining the high level performance for which JVC is world famous. The
JVC service and engineering organization stands behind our products.
NATIONAL HEADQUARTERS
JVC SERVICE & ENGINEERING COMPANY OF AMERICA
DIVISION OF US JVC CORP.
107 Little Falls Road
Fairfield, NJ 07004-2105
If you ship the product...
Pack your JVC unit in the original carton or one of equivalent size and strength. Enclose, with the unit, a letter stating the problem or symptom that exists and also a copy of the receipt or bill of sale you received when you purchased your JVC unit. Print your home return address on the outside and the inside of the carton. Send to the appropriate JVC Factory
Service Center as listed above.
ACCESSORIES
To purchase accessories for your JVC product, you may contact your local JVC Dealer.
Or from the 48 Continental United States call toll free:
1-800-882-2345.
Don't service it yourself.
CAUTION
To prevent electrical shock, do not open the cabinet. No user serviceable parts inside.
Refer servicing to qualified service personnel.
62
EN
WARRANTY (Only in U.S.A.)
LIMITED WARRANTY
CONSUMER VIDEO 1-90
JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE ORIGINAL
PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of original retail purchase for the period as shown below. ("The Warranty Period")
PARTS LABOR
1
YR
90
DAYS
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND IN
COMMONWEALTH OF PUERTO RICO.
WHAT WE WILL DO:
If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner. Such repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized service centers. Parts used for replacement are warranted only for the remainder of the Warranty Period. All products and parts thereof may be brought to a JVC authorized service center on a carry-in basis except for Television sets having a screen size 25 inches and above which are covered on an in-home basis.
WHAT YOU MUST DO FOR WARRANTY SERVICE:
Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized service center, please call toll free: (800) 252-5722.
If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with a copy of your bill of sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center, the name and location of which will be given to you by the toll-free number.
If you have any questions concerning your JVC Product, please contact our Customer Relations Department.
WHAT IS NOT COVERED:
This limited warranty provided by JVC does not cover:
1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation, lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized by JVC to render such service, or if affixed to any attachment not provided with the products, or if the model or serial number has been altered, tampered with, defaced or removed;
2. Initial installation and installation and removal for repair;
3. Operational adjustments covered in the Owner's Manual, normal maintenance, video and audio head cleaning;
4. Damage that occurs in shipment, due to act of God, and cosmetic damage;
5. Signal reception problems and failures due to line power surge;
6. Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90 days from the date of purchase;
7. Accessories;
8. Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase); from the date of purchase);
There are no other express warranties except as listed above.
THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IS
LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN.
JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY OTHER
DAMAGES, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGE TO
TAPES, RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH
OF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SET
FORTH ABOVE.
Some states do not allow the exclusion of incidental or consequential dameges or limitations on how long an implied warranty lasts, so these limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
JVC COMPANY OF AMERICA
DIVISION OF US JVC CORP.
41 Slater Drive
Elmwood Park, New Jersey 07407
REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR DETAILS OF
REFURBISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION
PACKAGED WITH EACH REFURBISHED PRODUCT.
For customer use:
Enter below the Model No. and Serial No. which is located either on the rear, bottom or side of the cabinet. Retain this information for future reference.
Model No.: Serial No.:
Purchase date: Name of dealer:
MEMO
EN
63
JVC COMPANY OF AMERICA
DIVISION OF US JVC CORP.
41 Slater Drive, Elmwood Park, N.J. 07407
JVC CANADA INC.
21 Finchdene Square, Scarborough Ontario M1X 1A7
COPYRIGHT © 1997 VICTOR COMPANY OF JAPAN, LTD.
U/U(C)
Printed in Malaysia
0497HOV * UN * PJ
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 6 Basic Connections
- 7 Plug & Play
- 8 Language
- 9 Clock
- 9 Preparation
- 10 Semi-Auto
- 11 Manual
- 12 Tuner
- 12 Set Receivable Channels
- 14 Add Or Delete A Channel
- 15 Cable Box Control
- 15 Situate And Connect Controller
- 16 Set Cable Box Output Channel
- 17 Set Cable Box Brand
- 18 VCR Plus+ Setup
- 20 DBS Receiver Control
- 20 Situate And Connect Controller
- 21 Set DBS Receiver Output Channel
- 22 Set DBS Receiver Brand
- 23 Simple Playback
- 24 Simple Recording
- 25 Playback Features
- 25 Still Picture/Frame-By-Frame Playback
- 25 Slow Motion/Reverse Slow Motion
- 25 Variable-Speed Search/Reverse Motion Playback
- 25 High-Speed Search
- 26 Manual Tracking
- 26 Tape Position Indicator
- 27 Video Stabilizer
- 28 Superimpose
- 29 Select The Soundtrack
- 30 Index Search
- 30 Instant ReView
- 30 Skip Search
- 31 Repeat Playback
- 31 Counter Reset
- 31 Counter Memory
- 31 Next-Function Memory
- 32 AV COMPU LINK Playback
- 34 Auto Picture
- 34 Preparation
- 35 Playback
- 36 Recording Features
- 36 Watching Another
- 36 Display Elapsed Recording Time
- 37 Stereo And SAP (Second Audio Program)
- 37 To Record SAP Programs
- 38 VCR Plus+ Timer Programming
- 40 On-Screen Timer Programming
- 42 Check And Cancel Programs
- 43 Auto Timer
- 44 Instant Timer Recording (ITR)
- 45 Edit To Or From Another VCR
- 46 Edit From A Camcorder
- 48 TV Multi-Brand Remote Control
- 49 Cable Box Multi-Brand Remote Control
- 50 DBS Receiver Multi-Brand Remote Control
- 51 Control Two JVC VCRs
- 52 Power
- 52 Tape Transport
- 52 Playback
- 52 Recording
- 53 Timer Recording
- 54 Other Problems
- 55 Playback
- 55 Recording
- 55 Timer Recording
- 56 List Of Terms
- 57 Front View
- 58 Rear View
- 58 Front Display Panel
- 59 Remote Control