Viakom VDA110HQX-VFA49LIR Instruction manual

HIGH RESOLUTION
COLOR CCTV CAMERA
INSTRUCTION MANUAL
VDA110 SERIES
VDA110HQX – VFA49LIR
By selecting this product, you have decided to use a professional device that guarantees
highest quality and reliability. We would like to thank you very much for your confidence and
kindly ask you to read the following instructions carefully before Installation and operation in
order to take full advantage of all quality features regarding this product.
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE THE COVER (OR BACK),
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
PERSONNEL.
The lighting flash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of dangerous
voltage within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and
maintenance
(servicing) instructions in the literature accompanying the appliance.
INFORMATION- This equipment has been tested and found to comply with limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
WARNING – Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
CAUTION –
To prevent electric shock and risk of the fire hazards:
Do NOT use power source other than that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be conducted by a qualified service person and should
conform to all local codes.
1. Precautions
2. Package
3. Features
1. Advantageous ways of installation
2. Protections from all kinds of conceivable dangers
3. State of the art image enhance technologies
4. Other features
4. Name and function of each part
5. How to operate key functions
1. Auto Iris lens
1. Extra Fuse
2. Extra Video output
3. DIP S/W functions
6. Installation
1. How to separate the camera set from the base
2. How to reposition the camera set into the base
3. How to reposition the cable to Conduit hole
4. How to connect the power
5. Installation overview
7. Trouble shooting guide
8. Specification
9. Warranty card
Please read the manual carefully before the installation in order to make use the
camera be set up correctly and to have the best picture quality.
Please keep the manual in good condition for your future reference and service
application.
Installation and services should only be carried out by an authorized personnel according to
local safety regulations.
Repairs and adjustments of the camera should be carried out by an authorized personnel.
If any liquid or solid matter gets into the housing, immediately disconnect the camera from
power supply and have it checked by your authorized dealer before reusing.
Avoid installing the camera at extremely hot or cold places.
If you are not a certified person, never try to dismantle the camera. To avoid electric shock,
never remove the screws or covers. There are no parts inside that need maintenance by the
user. All maintenance should be carried by qualified personnel.
Avoid installing the camera at a place of high humidity.
Avoid installing the camera at the place exposed to gas or oil.
Don't try to disassemble the camera. There are no serviceable parts inside.
When there is any problem, please refer to a service personnel at the shop where you bought.
Keep the top glass of the lens always clean in order to obtain the best picture quality
all the time. Be careful not to be stained by fingerprint.
Don't face the camera directly toward sunlight or sunlight reflecting area.
CCD may go defective at this condition.
Please give a special attention to keep the unit from dangerous drop or
external shock during the process of transportation or handling.
Never try to touch the camera in wet hand. It may cause an electric shock.
Do not expose the camera to radioactivity. It causes a serious damage on the CCD.
Note for 12VDC Power type camera user
Make sure to use a regulated 12VDC power source.
Check the power with the power tester to make sure if the power supply gives an
exact 12VDC regulation. Even sometimes UL marked power supply unit generates
unstable power causing the camera to burn in many cases.
1. Color Camera VDA110 ------------------- 1EA
2. Instruction manual ----------------------------------1EA
3. Fuse -------------------------------------------------------------1EA
4. Sponge plate ------------------------------------------------1EA
5. Wrench Driver--------------------------------1EA
6. Mounting screws ---------------------------------1EA
7. Extra Video output cable----------------------------------1EA
8. Ceiling mount Adaptor plate -----------------------------------------1EA
! "#
$ %
A. Tool-free 3- Axis mounting mechanism
& '
Panning axis up to 360’ degree
Tilting axis up to 90’ degree
Rotation axis up to 180’degree
No need to use a tool for adjustment!
All adjustments are done quick and easy with hand!
: Angle adjustment from each of 3 different axes can be positioned to its maximum
angle of view so that the camera gets the full central picture at any location.
B. Separatable camera set
&
(
Dome base can be installed in advance where
Construction is not completed or for customized system integration
(
(
(
If it is necessary to change or renew the camera after the installation,
there is no need to take off the whole product and cabling. Just change
the camera set with two locking screws on and off within a minute.
C. Save cost and time for the maintenance of dome
( "
#
" %(
"
When the dome clear part in front of the lens has a scratch or
contamination, the whole part of the dome cover set had to be
disassembled for a renewal of the clear part in conventional dome
cameras.VDA110’s dome cover is rotated by hand to eliminate the
complicated procedures. Just turn the cover to a clear position
when the window part is damaged. No professional workmanship
is required. IP66 weatherproof is valid after rotation!
D. Industrial standard mounting arrangement
)
(
"
" " &
*
'
The mounting hole is compatible to the
standard electric junction box for a quick
and easy installation.
+,
" "
"
(
Pipe insertion from the side or from the
back of the dome is provided.
E.
Additional service monitoring output
Additional Video Output
terminal is provided so that the
installer can adjust the
zoom/focus and functioning
control on the spot.
!
)
"
#
"
A. Vandal-proof
The body is made of 4.0mm thick die-cast and the dome made of 2.2mm thick polycarbonate
to be protective from a high impact of vandalism on the dome.
B. Tamper resistant
The dome is secured with a tailor-made stainless steel safety screws. (Option)
C. Free from Shock and Vibration
The tool-free internal 3-axis mounting mechanism is strong enough to hold the camera set
against severe vibration or shock on the dome.
D. Rust free against salty environment
The VDA110 is fully protected from a salt mist environment with hard salty-water resistant
coating.
E. Dust and Moisture free (IP66 Weatherproof)
The unit is duly passed IP66 international weatherproof standard, allowing the camera free
from moisture and dust.
F. Fire resistant
Hard die-cast body and fully metallic internal camera mount mechanism is designed to be
totally protective from fire breaks or fire interception.
1/2” Conduit-holes are provided for fire resistant cable management.
G. Perfect Surge voltage protection
Extra fuse for surge protection
The VDA110 builds-in a highly reliable surge absorptive circuit so as to protect
the camera from an excessive voltage input. Moreover, it has an extra
interchangeable fuse at the entrance of the power circuit to cut off any voltage
shock before the power gets into the camera’s power circuit.
H. Protection from extreme temperature range of 40˚ F~122˚ (-40˚ C~ + 50˚ C)
"
%)
The VDA110 provides a highly reliable heater option for an application of
area where the temperature comes down to -40˚ C cold.
3) State-of-the-art image enhance technologies
A. True Day & Night image conversion for 24 hours clear view
%+ ( $
(
The image is converted to B/W mode from Color and the IR responsive filter
is automatically moves in at 5 lux darkness.
$ ( .
+
$ ( /
This dual filter mechanism is uniquely designed to have a blue filter in daytime
for a precise color reproduction and to have an IR focus corrective filter at
nighttime so that there is no focus shift when the IR lights are activated.
B. Highly enhanced resolution of 560TVL(Day) & 600TVL(Night)
!"
#$ ! "
The VDA110HQ ideally combines a precise full glassed
optics and newly developed professional DSP chip with Sony
Super HAD CCD image sensor to deliver ultra clear image of
500TVL in daytime color. The image is automatically
converted from Color to black & white at 5 lux darkness to
make the image quality extremely clear and to enhance the
resolution up to 540TVL at night.
C. The Maximum sensitivity with the best sensor and the latest techology
Used with the latest high sensitive sensor the
VDA110HQ provides the highest performance in low
light at 0.2 Lux/F1.3 (Super HAD)/0.1Lux (Ex-view
HAD). In addition the built-in true Day/Night function
completely removes the color signal noises for an ultra
clear night time image quality.
D. Wide range of Automatic White Balance (1,800˚ K~ 10,500˚K)
The VDA110HQ’s Automatic White Balance provides
an extensive range of color temperature control that
covers from 1,800’K to 10,500’K, generating a natural
color image without being red or blue in varying light
conditions.
E. Intelligent image compensation against IR saturation
VDA110HQ
Can you recognize the picture when the object
is getting closer to a strong IR illumination?
A new image processing technology is adapted to
eliminate the ‘WHITE OUT’ problem. Now the
picture is automatically processed so that the
camera can observe recognizable objects instead
of seeing all white saturation.
F. Greatly improved Day & Night response
Does the picture converts itself between color and b/w at the right time exactly and is the IR
illumination on and off at the same time as well?
A new technology of Day and Night control is added to this device. An accurate control of image conversion
and a precise operation of day & night filter movement at the right moment, gives a reliable image capturing
capability in Color mode at daytime and in B/W mode at nighttime.
)
% &
/%
#-1
% &
% &
%
()
*
'%
)
*
)
% &
/% 0
#-1
0
0
.
2
2
+, %-
- '.
.
&
)
% &
%
%
0
'% .
)
*
+
%-
- '.
G. Non-IR reflection
Does IR lightings are reflecting?
Unlike conventional IR LEDS integrated dome
cameras; this unit provides a smart mechanism that
eliminates IR reflections. Users can easily set up
the camera’s position without having a big hassle
for eliminating IR reflection.
)
** /
% &
% &
H. Clear image quality under IR illumination
Does IR responded image clear?
When IR illumination is combined, the IR responded
image becomes defocused. This unit incorporates a
clear solution for this conventional problem. The image
quality of this unit is absolutely sharp and clear under IR
lights in operation.
/ -
0!
(
)
*% &
-
A. 4-9mm (2.5 x Zoom) IR Extra-low dispersion glass vary-focal Lens
The unit incorporates 4mm-9mm optical zoom lens that
utilizes extra low dispersion glasses for Day& Night use.
, %
4
6 3.#1 4
5 %
B. Dual switching power (w/Auto Line-lock)
The unit builds in highly efficient switching power control that self configures 12VDC or 24VAC
input and 24VAC line pulse automatically (Automatic line-lock). Double insulated power design
guarantees no ground loop when used with multiple cameras and system equipments together
through one power source.
0
"
()
'
%$ & !
#
" DC IRIS CONTROL VR
To control a shutter speed of DC Iris lens.
DIP S/W
No.1: BLC
(Switch ON = BLC ON)
No.2: AGC
(Switch ON = AGC max, Switch OFF = AGC normal)
No.3: GAMMA
(Switch ON = Gamma 1, Switch OFF = Gamma 0.45)
No.4: AWB
(Switch ON = Push Lock mode, Switch OFF = ATW mode)
No.5: FLIKERLESS (Switch ON = Flickerless ON)
FUSE
To protect the camera from surge Voltage/Current input and to reuses the camera by simply
replacing the fuse when a surge power is interrupted.
Extra video output
To enable an installer to check and adjust the camera set up via service monitor on the spot.
Power input
To provide power to the camera
V_PHASE CONTROL VR
To adjust the V_PHASE level from 0° to 360° when 24VAC Line lock is required.
HEATER OPTION
To connect the heater unit. Heater is option.
1 - $
)
%
1) Auto IRIS (DC iris lens) control
This is an automatic function that optimizes the amount of light reaching to a CCD by driving
the lens that has a mechanical shutter speed control built-in. Default light level is adjustable by
turning the DC-Iris volume left or right direction by using a screw driver.
2) Extra Fuse for surge power interruption protection
The camera incorporates highly reliable surge absorptive circuit so as to protect the camera
from an excessive voltage input. In addition, it has an extra interchangeable fuse at the
entrance of the power circuit to cut off any voltage shock before the power gets into the
camera’s power circuit.
- Extra Fuse is included in the package.
-
Please check the fuse first when there is no
power/video from the camera.
(
- When the fuse is cut off, check if power and
ground of the cable or terminal be shorted out.
-
Replace the fuse.
-
Replace the power supply within the specification,
when the fuse goes out repeatedly,
How to check the Fuse
1.
Check the fuse with Multi meter.
2.
Fuse is OK when ) 0 *,+ is detected.
3.
(
(
Fuse is N.G when ) M *,+ is detected.
Fuse specification and vendor: 250V/1A, Bussmann
Fuse length of life
1.
The fuse works forever when the power input is correctly supplied.
2.
Fuse will be cut off only when there is a short or over voltage input during the
installation. But when the image goes dead after the installation, it means that the
fuse is OK but the camera is defected. Replace the camera in this case.
3.
How to purchase the fuse : It is a standard and widely available in general electronic
shopping center. Please refer the defected fuse to the electronic shop for the same
specification.
3) Extra Video output
This is aimed for the installer to check camera angle and function adjustments on the spot via
service monitor.
(
Extra BNC cable is included in the
package.
4) DIP/SW functions
NO
Function
S/W=>ON
S/W=>OFF
1
BLC
BLC ON
BLC OFF
2
AGC
MAX
Normal
3
GAMMA
1
0.45
4
ATW/PUSH
PUSH
ATW
5
F/L
F/L ON
F/L OFF
BLC (Back light compensation)
When the camera faces directly toward bright light entering place like window, door or bright
background, electronic iris function makes a negative effect by making the object become too
dark resulting in the object unrecognizable. This camera offers a BLC on/off function to get the
clear object on this light condition.
AGC (Automatic Gain Control)
AGC off mode offers a noiseless picture at low light condition. Put the switch ON (AGC ON) in
order to get a brighter view at dark situation.
Auto White Balance (ATW/PUSH)
White balance control is selectable to Push lock mode or ATW mode according to the
environment. ATW mode is recommendable when the background is one colored such as all
green. Normal camera makes green to white while ATW mode tracing it as a true green. Push
lock mode is recommendable when the camera is installed under indoor fluorescent light
environment. It prevents the picture changing between blue and red affected by the fluorescent
light.
* Color temperature range: ATW < 2100˚K ~ 9100 ˚K >
PUSH < 2100˚K ~ 10000 ˚K >
* Factory set-up is Push lock mode
CAUTION
Please note that following errors can happen at ATW mode
- The object in from of the camera is big with one color or when there is no white color
around the object.
- When the camera is used under a special lighting like sodium.
-/.1023,4502768:9;2<%4 ’= 8><?%@&AB6&C3DFE = 2345E AB2G H7AB2D6&AI8G C2J
Gamma
Gamma is used to compensate the signal distortion at CRT monitor.
Gamma ON is standard set up for CRT monitor (r=0.45). Gamma OFF is r=1.
- Factory set up is ‘ON’
F.L (Flickerless)
F.L on is used when the picture is shaking under the fluorescent light affected by difference
between the display system(60Hz) and AC power signal(50Hz) only.
2
Installation and services should only be carried out by an authorized personnel according to
local safety regulations.
Should liquid or solid matter gets into the housing, disconnect the camera immediately from
the power source and have it checked by your authorized dealer before reusing it.
Keep an adequate distance from direct heat sources.
Avoid installing the camera at a place of high humidity.
Avoid installing the camera at a place exposed to gas or oil.
Keep the top glass of the lens always clear in order to obtain the best picture quality all the
time. Be careful not to stain the lens and the outer glass by fingerprints.
Do not point the camera toward artificial lightings, the sun, the sky or to the direction of a
window. The best picture quality will be achieved if both camera and lighting point to the
area you want to record.
Do not expose the camera to radioactivity. It causes a serious damage on the CCD.
Do not put objects inside the unit. Make sure that no metal objects or flammable substances
get into the camera. It could cause fire, short-circuits or damages.
Install away from electric or magnetic fields.
1) How to separate the camera set from the base
<DRW 1-1>
<DRW 1-2>
<DRW 1-3>
Take off 4*8 Screws (2 pcs) as in Drawing 1.
Grab the two hinges at both ends with both hands.
Push the hinges inward to lock off the camera-set from the base as in Drawing 2.
Lift the camera-set from the base as in Drawing 3.
2) How to reposition the camera set into the base.
Hinge
Frame
Grabber
<DRW 2-1>
<DRW 2-2>
<DRW 2-3>
Locate the camera set with the hinges right onto the frame grabbers and gently push
down the camera-set onto the base as in the DRW 2-1.
Push the camera-set down onto the base with enough strength until it sounds ‘click’ as in
the DRW 2-2. The hinges clip the camera-set onto the base with its tension. When no
sound heard, please push the camera-set down again as in the pictures below.
(Unfinished)
(Finished)
Fix the camera with 4*8 Screws onto the base as in the DRW 2-3.
3) How to reposition the cable from the back to the side of base
L
'
K
!
<DRW 3-1>
<DRW 3-2>
<DRW 3-3>
DRW 3-1 is factory set up. The cable comes out to the back of base.
Plug out the power input connector with hand as in DRW 3-2.
Screw off the cable tie and the safety wire (Hanger) as in the DRW 3-3.
<DRW 3-4>
<DRW 3-5>
<DRW 3-6>
Pull out the Cable, O-Ring and Hanger from the base as in DRW 3-4.
Take off the Conduit cap with a coin as in DRW 3-5. Please reuse the conduit cap to
cover the conduit hole at the bottom of the base.
M
N
Put the cable into the base through the side conduit hole as in DRW 3-6.
O
<DRW 3-7>
<DRW 3-8>
Fix the cable and the safety wire (Hanger) with cable tie and screw as in DRW 3-7.
Plug in the power connector to the camera board as in DRW 3-8.
4) How to adjust the Zoom/Focus.
a. Parts location
P
Zoom locking
Lever
Focus locking
Lever
Pan locking Ring
Tilt locking
Lever
QSRUTVXWVZY T"[
\ W"[&]_^ `
b. Zoom/Focus adjustment
Zoom locking
Lever
Zoom and Focus locking levers are screwed up
and positioned at top side so that they can be
accessed by hand at factory.
Focus locking
Lever
1. Please loosen the zoom/focus levers a little
bit by turning them counter-clockwise with
finger.
2. Move the lever left or right to adjust the zoom
and focus.
3. Please lock them tightly after the adjustment
by turning them clockwise with finger.
5) How to adjust the camera angle.
a. Pan 180°
Angle adjustment either to the
left direction or right
direction
within 180° is possible.
1. Hold the Pan locking ring with
hand and loosen it by turning it
counterclockwise as in the
picture left.
2. Adjust the panning angle and
lock the Pan locking ring by
turning it clockwise as in the
picture.
b. Tilt 90°
Angle adjustment of up to
maximum 90° downward is
possible.
1. Hold the Tilt locking levers
on both sides with hand and
loosen it by turning it
counterclockwise as in the picture
left.
2. Adjust the Tilt angle with
hand and lock the Tilt locking
lever by turning it clockwise as in
the picture.
c. Rotation 360°
Angle adjustment either to the left
direction or right direction within 360° is possible
- Grab the both ends of the Rotation handle as in
the picture and adjust the angle to the direction
you want.
6) How to connect the power
Video out
Power in
Connect the copper wire of the power cable to the screw terminal provided at the end of the
camera cable.
Required power supply
For 24VAC: 24VAC/500mA
For 12VDC: 12VDC/1000mA regulated.
7) Installation overview
!
&
%
- 7 44
/
-44
7 /
-&
&
/
6
!2
&- .
/
/ /
&
8
% 2 4 &
- '
/
8
-
:
6
-44
!
%
-44
3% -
%
%- 4 4
6
6
6
%7
7
.
% -
7 2 /
4 4 '.
/
&
3& &
'6
&
7
.
4
'
4
7 .
%4 7
9
7 1.
- '
4 2&.
4
&
1
.8
6
% /
/%
7
6
6.
'
%
1
%
97.
6
& 4
. ,
/
/
3
(
"
Before sending the camera out for repair, check the items below. If the problem persists after
checking these items, contact your service center.
Problems
Nothing appears on the
screen.
Trouble shooting
Please check the power connection.
Please check the video signal line connection.
The video image is not
clear.
Please check if the lens or the outer glass is clean.
- Dirt or fingerprints on the lens can affect the image
blooming or reflection. Gently wipe any dirt or
fingerprints off the lens or the glass with a soft cloth.
Please check and adjust contrast feature of the monitor
Please check if the camera is exposed directly toward a
bright light, sunlight, or sun light reflecting area.
Please move the camera’s position in this case.
The screen is dark.
Please check and adjust contrast feature of the monitor
If there is any interim equipment, set the 75 position
properly and check the terminals.
Please check if the power supply is within the
specification.
- When the cable connection requires a long distance,
there may need a higher power supply or an additional
power/video amplification.
The camera’s surface is too
hot and black stripes
appear on the screen.
Please check if the power supply is regulated and is
within the standard requirement of the product.
The screen is flickering.
Please check if the camera is facing directly toward
sunlight or fluorescent light.
IR beam is weak
Check if the distance of the cable installation is too long
or if the cable is not UL standard. Using a lower grade
cable or long distance cable installation can cause a
serious voltage drop. Please check the voltage output
level of the cable and change the power source in this
case. Make a special care not to supply too much
power over the camera as well.
4 5)
Specification
Description
MODEL
VDA110HQ-VFA49LIR
Image
Image sensor
Effective Pixels
H.Resolution
1/3" Sony Super HAD CCD 1/3" Sony Ex-view HAD CCD
768(H) x 494(V) - NTSC, 752(H) x 582(V)-PAL
NTSC: 560 TV Lines (Day)/ 600 TV Lines (Night)
PAL: 520 TV Lines (Day)/ 580 TV Lines (Night)
Electrical
Sync system
Scanning system
Video output
S/N ratio
Min. Illumination
IR Distance
BLC
White balance
Gain Control
Gamma correction
Shutter speed
Internal (12VDC input) /Line lock (24VAC input)
NTSC 525 lines PAL 625 lines 2:1 Interlaced
1.0 Vp-p composite. 75 Ohms
More than 50 dB (AGC Off)
‘0.2’ Lux /F1.3 (IR ‘off ‘)
‘0.1’ Lux /F1.3 (IR ‘off ‘) - EX
‘20M’ (Super HAD)
‘30M’ (Ex-view HAD) - when “IR On”
On / Off
Automatic (1800˚K~10,500˚K)
Nor/Max
r=0.45
1/60 a 1/120,000 sec (NTSC)
Power
Power source
Operating current
Mechanical
Lens
Lens Option
IR spectrum
True Day/Night
Environmental
Operating Temp
Category
Humidity
Physical
Output Terminal
Measurement (mm)
Weight (Approx.g)
VDA110HQX-VFA49LIR
1/50 a 1/100,000 sec (PAL)
12VDC/24VAC Dual power
At 12VDC: 190mA (IR ‘off ‘-Day) / 440mA (IR ‘on’ - Night)
At 24VAC: 100mA (IR ‘off ‘-Day) / 180mA (IR ‘on’ - Night)
4mm~ 9mm Vary-focal DC iris
9mm~ 22mm Vary-focal DC iris
850nm-30° x 21ea
Automatic image change from Color (Day) to B/W (Night).
14˚ F~122˚ F (-10˚ C~ + 50˚ C)
-40˚ F~122˚ F (-40˚ C~ + 50˚ C) – with heater option
Within 90% RH
4 Ft DIY cable w/BNC-Fe for Video, terminal block for Power
121.5(D) x 164(L)
1400
Specifications are subject to change without prior notice for improvement.
;