JVC RA-P11BK User's Manual

Getting Started
 Supplied Accessories
After unpacking, check to be sure
that you have all the following items.
•
•
•
•
•
PORTABLE AUDIO SYSTEM
RA-P11BK
Remote control
AC adaptor
Attachments (6 types)
Rubber pads (A type×2, B type×2)
CR2025 (×2) lithium coin batteries
One is loaded on the remote
control at the factory.
 Preparation of the Unit
Insulation sheet
 Prepare the Remote
Control
• When you use the remote
control for the first time, pull
out the insulation sheet.
(Front side)
Replacing the Battery
in the Remote Control
• Insert the battery into the
remote control by matching
the polarity (+ and –)
correctly.
Lithium
coin battery
(CR2025)
(Rear side)
 Loading batteries for the Unit (The battery power supply)
Insert three batteries to each compartment (six batteries total). Be sure to match the poles (+/-) correctly.
While the AC adaptor is connected to the wall outlet, the unit works without batteries.
R6 (SUM-3)/AA (15F) (not supplied)
Warning
• Store the battery in a place where children cannot reach. If a child accidentally swallows the battery,
consult a doctor immediately.
• Do not recharge, short, disassemble or heat the battery or dispose of it in a fire. Doing any of these things
may cause the battery to give off heat, crack, or start a fire.
• Do not leave the battery with other metallic materials. Doing this may cause the battery to give off heat,
crack, or start a fire.
• When throwing away or saving the battery, wrap it in tape and insulate; otherwise, the battery may start to
give off heat, crack, or start a fire.
• Do not poke the battery with tweezers or similar tools. Doing this may cause the battery to give off heat,
crack, or start a fire.
• Dispose of battery in the proper manner, according to federal, state, and local regulations.
• The batteries (battery pack or batteries installed ) shall not be exposed to excessive heat source such as
sunshine, fire or the like.
CAUTION:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
 Connecting the AC adaptor
Open the battery compartment
cover by pressing the small tab.
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to
obtain the best possible performance from the unit.
Close the cover in the order shown by the numbers.
To a wall outlet
Plug the AC adaptor
only after all connections
are completed.
9V 1.5A
AC adaptor: AA-R9031 (supplied)
CAUTION:
To avoid risk of fire, and to prevent damage.
• Do not use AC adaptors except for the supplied AC adaptor.
• Do not use the supplied AC adaptor for other equipment.
9V 1.5A
FM wire antenna
(Pass through the notch in the cover)
Operating on the Remote Control
 Loading batteries for the Clock
Be sure to match the poles (+/-) correctly.
INSTRUCTIONS
Lithium coin battery
(CR2025) (supplied)
Plus terminal
Plus terminal
Side of the battery
1
LVT1686-002A
[C]
EN
©2006 Victor Company of Japan, Limited
Press the tab to open
the cover.
Warnings, Cautions and Others / Mises en garde, précautions et indications diverses
(For U.S.A)
Precautions
(For U.S.A)
CAUTION
Changes or modifications not approved by JVC
could void the user’s authority to operate the
equipment.
For Canada/pour le Canada
THIS DIGITAL APPARATUS DOES NOT
EXCEED THE CLASS B LIMITS FOR
RADIO NOISE EMISSIONS FROM DIGITAL
APPARATUS AS SET OUT IN THE
INTERFERENCE-CAUSING EQUIPMENT
STANDARD ENTITLED “DIGITAL APPARATUS,”
ICES-003 OF THE DEPARTMENT OF
COMMUNICATIONS.
• Install in a place which is level, dry and neither too
hot nor too cold–between 5°C and 35°C.
• Install the System in a location with adequate
ventilation to prevent internal heat buildup inside
the System.
DO NOT install the System in a location
near heat sources, or in a place subject to
direct sunlight, excessive dust or vibration.
• Leave sufficient distance between the System and
the TV.
• Keep the speakers away from the TV to avoid
interference with TV.
CET APPAREIL NUMERIQUE RESPECTE LES
LIMITES DE BRUITS RADIOELECTRIQUES
APPLICABLES AUX APPAREILS NUMIRIQUES
DE CLASSE B PRESCRITES DANS LA NORME
SUR LE MATERIEL BROUILLEUR; “APPAREILS
NUMERIQUES”, NMB-003 EDICTEE PAR LE
MINISTRE DES COMMUNICATIONS.
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
• Rating label is placed on the exterior of the bottom.
• L’étiquette des caractéristiques nominales se
trouve sur l’extérieur du coffret.
RA-P11BK_C_EN_002A.indd 1
(For U.S.A)
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV
technician for help.
15cm
15cm
15cm
10cm
15cm
15cm
2
3
In These Cases
Power does not come on.
No longer works.
Cannot set the iPod.
Check the following points
• AC adaptor is not inserted securely. Plug in securely.
• The batteries are exhausted.
Press the “RESET” button (see “Resetting the unit”).
• Is the selected attachment compatible to your iPod? Confirm the
compatibility of iPod and attachments in “iPod Compatibility Chart”.
• Is the attachment properly mounted on the unit? Make sure to mount the
attachment properly.
• Is the iPod firmly connected to the connector plug of the unit?
• Is the iPod properly functioning? Test the iPod functions in stand alone
condition.
• Is the iPod firmly connected to the connector plug of the unit?
• Is the AC adaptor connected? Make sure the AC adaptor plug is pushed in
all the way.
The iPod cannot be charged while the Unit is operated on batteries.
• For iPod 3rd Generation, set the “CHARGING SWITCH” to “FIREWIRE”
(see “Charging the iPod”).
The FM antenna is not properly extended and positioned.
Hard to listen to broadcasts
because of noise.
Unable to operate the System • The path between the remote control and the remote sensor on the
from the remote control.
System is blocked.
• The batteries are exhausted.
When the volume level is
The unit’s battery runs low (The “---” (Low battery) appears on the display).
manually set higher than “08”, Replace the batteries with new ones.
the unit automatically lowers
the level to “08”.
If “Troubleshooting” does not eliminate malfunctioning (failure to operate or
display properly, etc.), press the “RESET” button on the rear of the unit with
something having a sharp point, while the unit is turned on. After pressing
“RESET” button, unplug the AC adaptor and wait a while before plugging it
again.
• When using “RESET” button, make sure the lithium coin battery is loaded.
• While resetting the unit, the clock is also reset. Adjust the clock after resetting
the unit.
6
7
4
8
5
6
7
If you are having a problem with your System, check this list for a possible solution before calling for service.
iPod cannot be charged.
Side
Côté
1
Troubleshooting
 Resetting the unit
Front
Face
3
Close the cover in the order
shown by the numbers.
4
Caution: Proper Ventilation
(For U.S.A)
Insert the battery with pushing the plus
terminal up to be sure the terminal
contacts the side of the battery.
Time to change the battery
As the battery is running out, the display indication dims or the alarm may beep at the time the alarm
is not set at. Replace the battery in such cases.
Cannot operate iPod.
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
Front: No obstructions and open spacing.
Sides/ Top/ Back: No obstructions should be placed in the areas shown by the dimensions below.
Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand
with a height of 10 cm or more.
Attention: Aération correcte
Pour prévenir tout risque de décharge électrique ou d’incendie et éviter toute détérioration, installez
l’appareil de la manière suivante:
Avant: Bien dégagé de tout objet.
Côtés/dessus/dessous: Assurez-vous que rien ne bloque les espaces indiqués sur le schéma ci-dessous.
Dessous: Posez l’appareil sur une surface plane et horizontale. Veillez à ce que sa ventilation correcte
puisse se faire en le plaçant sur un support d’au moins dix centimètres de hauteur.
2
5
1106NSMCREBET
8
NOTES
SOURCE button
Switch the sound source.
FM MODE button
Switch FM stereo/monaural.
MUTING button
Turn off the sound. Return to original mode by
pressing again.
PRESET +/- button
Select a registered FM radio station (P01 to 20).
iPod 6 button
Play/pause the iPod.
button
Switch the backlight on/off.
4/¢ button
Fast-forward/rewind the iPod song.
Change frequencies to tune in to FM radio
station.
VOLUME +/- button
You can adjust the volume level from 00 to a
maximum of 20.
• Point the remote control at the remote control sensor on the front panel.
• The remote control sensor is designed to receive signals from up to approximately 7 m distance when
the remote control is pointed directly. If the remote control is pointed with an angle, the distance may
become shorter.
Specifications
Model
Type
Amplifier
Input Sensitivity/ Impedance
FM Tuner
Speaker
Input Terminal
Power Source
AC adaptor
Dimensions (W x H x D)
Weight (Without batteries)
Accessory
RA-P11BK
Portable audio system
Power Output
4W x 2
1kHz 10% THD, 6Ω
AUX Input
250mV/47kΩ
Tuning Range
87.5MHz - 108.0MHz
Frequency Step
100kHz
Preset Stations
20
1way full range, diameter 35mm x2
External DC IN ( for AC adaptor)
AUX IN (mini jack)
DC9V
1.5A (EXTERNAL DC IN)
DC9V
(SIZE R6, AA BATTERY OR EQUIVALENT x6)
DC3V
(CR2025, for the clock)
Input : AC 110-240V , 50/60Hz
Output : DC 9V
1.5A
(W) 331 mm x (H) 71 mm x (D) 98 mm
0.7kg
See Supplied Accessories
Specifications and appearance are subject to change without prior notice.
2006-11-14 11:23:48
Basic and Common Operations
Press
Press
Playing back from iPod
Functions
• Light the display screen for 5 seconds when the power is
turned off.
• Temporarily stop the alarm sound when the alarm is ringing
(SNOOZE).
(see “Stopping alarm sound”)
 Turn on or off the power
Press
 Adjust the volume
Functions
Turns on or off the power
Press
When the power is turned off at volume level “15”
or higher, the unit automatically sets the volume
level to “14” the next time it is turned on.
Functions
Switch the temperature
display between Celsius/
Fahrenheit.
Functions
Adjust the volume level from 00 to a
maximum of 20.
–: Turn down the volume.
+: Turn up the volume.
Press
iPod connector plug
FM MODE/
¢
4
6
Functions
• Switch on/off the backlight when the
button is held down.
• Switch FM stereo/monaural when FM is
selected.
(see “Playing back from iPod” and
“Listening to FM Broadcasts”)
Press
See “How to set the
time and use the alarm”
 Display Information
Sound source indicator
When adjusting the volume
When FM radio is selected
Date
Current time/
alarm time
Day of the week
Temperature
Functions
Select a source
iPod → FM → AUX
Remote control
sensor
iPod/FM/AUX (blinks while muted)
00 - 20
P01 - P20 (channel) /
87.5 - 108.0 MHz (frequency)
iPod (slow blinking)
When the source is set to iPod and the
alarm is set to TIMER PLAY
When the source is set to FM radio and 87.5 - 108.0 MHz ↔ P01-P20
the alarm is set to TIMER PLAY
When battery power is low
--When trying to set alarm to TIMER PLAY
while selecting AUX
 Explanation of Icons
“STEREO” is displayed when an FM stereo broadcast is received.
“MONO” is displayed when the monaural is selected. (see “Listening to FM Broadcasts ”)
Off: current time / On: alarm time
Off: alarm off / On: alarm on / Blinking: alarm sounding (When “TIMER PLAY” is set)
Current time: Blinking / Other Clock Display: Lighting
Blinks while snoozing (the alarm is paused)
Listening to the iPod
1
1
2
3
Select the attachment compatible to your iPod (see “iPod Compatibility Chart”).
2
Connect the iPod to the unit.
Turn the unit power on.
Select “iPod” with the “SOURCE” button.
When iPod is selected as sound source, it automatically starts playback.
Press
Remote control
Unit
Attachment name
Match the attachment tab to the hole in the unit, and insert the attachment to the unit.
Functions
6
Playback/Pause
Press and hold this button to switch the iPod to sleep mode.
¢
Next song / fast forward (press and hold)
4
Previous song (Press this button during playback to jump back
to the beginning of the track.) / fast rewind (press and hold)
Charging the iPod
3
 Select a source
The temperature sensor and the
buzzer are located at the bottom
of the unit.
Setting the iPod on the unit
Connect the iPod to the connector plug of the unit.
• Always set volume to the minimum level when connecting or disconnecting iPod.
• When you connect your iPod to the unit, make sure you insert it all the way.
• When disconnecting the iPod, make sure that the System is turned off.
The iPod is charged while it is set on the unit when the Unit power is on.
• Connect the AC adaptor to the Unit. The iPod battery is not charged while
the Unit is operated on the battery power supply.
• The iPod is charged regardless of the sound source selected on the Unit.
• See the iPod instruction manual about charging times.
• The “CHARGING SWITCH” is located inside of battery compartment on
the rear of the Unit.
Set the “CHARGING SWITCH” to “FIREWIRE” for 10GB/15GB/20GB/
30GB/40GB iPod 3rd Generation. For all other models, you can set the
switch to either “FIREWIRE” or “USB” to charge the iPod.
CHARGING SWITCH
 How to combine the rubber pads with the attachment
 iPod Compatibility Chart
4 GB mini 1st Generation
iPod nano iPod nano 2nd Generation iPod video 5th Generation iPod video 5th Generation
iPod model
4 GB mini 2nd Generation
1GB/2GB/4GB
2GB/4GB/8GB
30GB
60GB/80GB
6 GB mini 2nd Generation
Attachment names
mini
nano
2G nano
VIDEO 30GB
VIDEO 60GB
There are two types of rubber pad : “A type (Large)” and “B type (Small)”.
Select the appropriate rubber pads for your iPod model.
A type (Large)
B type(Small)
Insert the rubber pads narrow-end first.
iPod 3rd Generation 10GB/15GB/20GB
iPod 3rd Generation 30GB/40GB
iPod 4th Generation 20GB
iPod 4th Generation 40GB
iPod photo 4th Generation 20GB/30GB
iPod photo 4th Generation 40GB/60GB
A type (Large)
B type(Small)
Combine this attachment with the rubber pads.
iPod
Select the rubber pad size which matches your iPod model.
iPod model
Rubber pad
Attachment name
• Select the appropriate attachment for your iPod model.
How to set the time and use the alarm
Switch/Press
Functions
Switch the alarm on/off.
OFF: turn off the alarm (BUZZER/ TIMER PLAY).
BUZZER: alarm on (buzzer sound)
TIMER PLAY: alarm on (iPod/FM radio)
• Switch between current time and alarm time.
• Press and hold this button to select the current time/alarm time setting mode.
Change the values for the time setting.
4
Switch to current time display with the “SET” button.
Press and hold the “SET” button. → The year display starts flashing.
While flashing, set each item with the “DOWN”/“UP” buttons.
Press the SET button.
• When the “SET” button is pressed, the flashing items will change in the following order.
Hour → Min. → TIMER PLAY time (10 to 30) → time display
• You can set the duration of time between timer-on and timer-off from 10 minutes to 30 minutes in TIMER
PLAY time.
2 If the power is off, turn the unit power on.
3 Confirm that you can hear the iPod or FM radio.
• Set to an appropriate volume.
4 Switch the “ALARM” switch to “TIMER PLAY”. The selected source is blinking on the display.
CAUTION:
• “AUX” cannot be selected as a source. Select another source.
• The “TIMER PLAY” does not work when the Unit power is turned off.
• The time is set when switching to time display from Minutes.
• The time can be set both when the power is on and off.
• To modify the setting, start again from step 1.
Stopping alarm sound
Setting the alarm (ALARM-BUZZER)
 To pause the alarm (snooze)
1
2
3
Switch to alarm time display with the “SET” button. → “ALARM” icon appears on the display.
Press and hold the “SET” button. → The hour display starts flashing.
While flashing, set each item with the “DOWN”/“UP” buttons.
• When the “SET” button is pressed, the flashing items will change in the following order.
Hour → Min. → TIMER PLAY time (10 to 30) → time display
• The connector plug is protected with a cover when it is first purchased. Please remove the
cover before operating the unit.
• Do not carry the System with iPod connected. You might drop it down or it might cause
damages to the connector part.
• Do not touch or hit the iPod terminal pins or the connector pins directly. It might cause
damages to the connector part.
• If the iPod does not play correctly, please update your iPod software to the latest version. For details about updating your iPod, check on the Apple web site <http://www.apple.com>.
• iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.
• JVC is not responsible for any loss of or damage to iPod that might result from the use of
this product.
• Sound distortion may occur when playing back audio sources with high recording levels.
When distortion occurs, it is recommended to turn off the equalizer of the iPod. For
information on operating the iPod, see the iPod instruction manual.
1 Set the alarm time.
(See steps 1 to 3 of “To set the alarm (ALARM-BUZZER)”)
Year → Month → Day → 12/24-hour time → Hour → Min. → time display
NOTES
NOTES
Selecting iPod or FM radio for the alarm sound (ALARM-TIMER PLAY)
Setting the Clock
1
2
3
4
Switch the “ALARM” switch to “BUZZER”.
• To check the set time, switch the display to alarm time by pressing the “SET” button.
• The buzzer sounds for three minutes.
Press the “SNOOZE/LIGHT” button while the alarm in sounding, when the alarm is set with either
“ALARM-BUZZER” or “ALARM-TIMER PLAY”.
The alarm sound is temporarily stopped, and started again 5 minutes later. You can repeat this up to 10
times.
Listening to FM Broadcasts
Unit
Press
Remote control
Switch FM stereo/monaural.
When there is too much static in an FM stereo broadcast, you
can reduce the static by switching to monaural reception.
Press again to switch back to stereo reception.
If the broadcast is not FM stereo, the sound becomes
monaural, even if FM stereo is selected.
• Switch channel display / frequency display. Channel display is
automatically switched to frequency display after approx. 3 seconds.
 To stop the alarm (BUZZER/ TIMER PLAY)
• Switch the “ALARM” switch to “OFF”.
FM MODE/
• It is not necessary to set the “TIMER PLAY” time at this point.
Playing back from other equipment
6
Connecting other equipment
Listening to external devices
Connect an external device to the AUX jack on the rear of the unit using a stereo mini plug cord (not
supplied) .
To audio output such as CD/
MD/digital audio player, etc.
1
2
3
4
NOTE
• Always set volume to the minimum level when connecting or disconnecting the other equipment.
RA-P11BK_C_EN_002A.indd 2
Turn the unit power on.
Select “AUX” with the “SOURCE” button.
Start playback on the external device.
Adjust the volume.
Listening to FM radio
Functions
—
Frequency display
Stretch out the wire antenna located on the rear of the unit before using.
1
2
3
Turn the Unit power on.
Select “FM” with the “SOURCE” button.
Select a station with the “4”/“¢” button.
Presetting Stations
1
2
3
Select “FM” with the “SOURCE” button, and switch to channel display with “6” button.
Use the “4”/“¢” button to select the channel number (P01 to P20) to be registered.
Press and hold the “6” button. → The channel number starts flashing.
4
Use the “4”/“¢” button to select the frequency (87.5 MHz to 108.0 MHz) of the station that you wish
to register.
Press the “6” button → The selected frequency will be registered.
Channel display
• To register a channel, press and hold this button. (see
“Presetting Stations”)
¢
4
Select a channel from P01 to P20.
(The unit button can be used when channel display is selected.)
5
¢
4
Change frequencies to tune in to FM radio station. (The unit
button can be used when frequency display is selected.)
• Press and hold to search broadcast stations automatically.
The search is finished when the signal is received. Press
again while searching to quit search.
• To confirm registration, select the registered channel number (P01 to P20), and press “6” button to
display frequency.
2006-11-14 11:24:00