AUDIO/VIDEO CONTROL RECEIVER
RX-6020VBK / RX-6022VSL
AUDIO/VIDEO CONTROL RECEIVER
FM/AM TUNING
FM/AM PRESET
FM MODE
STANDBY
PTY–PTY SEARCH–PTY
MASTER VOLUME
MEMORY
STANDBY/ON
SURROUND ON/OFF
INPUT ANALOG
INPUT DIGITAL
ADJUST SETTING
DVD MULTI
FM MODE
DVD
VCR
TV SOUND
TAPE/CDR
FM
AM
INPUT ATT
SURROUND MODE
CONTROL
DOWN
UP
SPEAKERS ON/OFF
CD
SOURCE NAME
PHONES
INSTRUCTIONS
For Customer Use:
Enter below the Model No. and Serial
No. which are located either on the rear,
bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
LVT0851-001B
[J]
RX-6020V/6022V[J]_COVER_f
1
3/4/02, 4:17 PM
Warnings, Cautions and Others/
Mises en garde, précautions et indications diverses
For Canada/pour le Canada
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT
ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQUAU FOND
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
For U.S.A.
The lightning flash with arrowhead symbol,
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
Changes or modifications not expressly approved by the
manufacturer for compliance could void the user’s authority to
operate the equipment.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
ATTENTION
Afin d’éviter tout risque d’électrocution, d’incendie, etc.:
1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le
coffret de l’appareil.
2. Ne pas exposer l’appareil à la pluie ni à l’humidité.
For Canada/pour Le Canada
THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS
B LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL
APPARATUS AS SET OUT IN THE INTERFERENCE-CAUSING
EQUIPMENT STANDARD ENTITLED “DIGITAL APPARATUS,”
ICES-003 OF THE DEPARTMENT OF COMMUNICATIONS.
CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE
BRUITS RADIOELECTRIQUES APPLICABLES AUX
APPAREILS NUMERIQUES DE CLASSE B PRESCRITES
DANS LA NORME SUR LE MATERIEL BROUILLEUR;
“APPAREILS NUMERIQUES”, NMB-003 EDICTEE PAR LE
MINISTRE DES COMMUNICATIONS.
Caution –– STANDBY/ON
button!
Disconnect the mains plug to shut the power off completely. The
STANDBY/ON
button in any position does not disconnect
the mains line. The power can be remote controlled.
Attention –– Commutateur STANDBY/ON
!
Déconnecter la fiche de secteur pour couper complètement le
courant. Le commutateur STANDBY/ON
ne coupe jamais
complètement la ligne de secteur, quelle que soit sa position. Le
courant peut être télécommandé.
Caution: Proper Ventilation
To avoid risk of electric shock and fire and to protect from damage.
Locate the apparatus as follows:
Front:
No obstructions open spacing.
Sides:
No obstructions in 10 cm from the sides.
Top:
No obstructions in 10 cm from the top.
Back:
No obstructions in 15 cm from the back.
Bottom:
No obstructions, place on the level surface.
In addition, maintain the best possible air circulation as illustrated.
Spacing 15 cm or more
Dégagement de 15 cm ou plus
RX-6020VBK/
RX-6022VSL
Wall or obstructions
Mur, ou obstruction
Front
Avant
Attention: Ventilation Correcte
Pour éviter les chocs électriques, l’incendie et tout autre dégât.
Disposer l’appareil en tenant compte des impératifs suivants
Avant:
Rien ne doit gêner le dégagement
Flancs:
Laisser 10 cm de dégagement latéral
Dessus:
Laisser 10 cm de dégagement supérieur
Arrière:
Laisser 15 cm de dégagement arrière
Dessous:
Rien ne doit obstruer par dessous; poser l’appareil sur une
surface plate.
Veiller également à ce que l’air circule le mieux possible comme illustré.
RX-6020V/6022V[J]_Safety_f
1
Stand height
15 cm or more
Hauteur du
socle: 15 cm ou
plus
Floor
Plancher
3/4/02, 4:23 PM
Table of Contents
Table of Contents
Parts Identification ...................................... 2
Getting Started ........................................... 3
Before Installation ...................................................................... 3
Checking the Supplied Accessories ........................................... 3
Putting Batteries in the Remote Control .................................... 3
Connecting the FM and AM Antennas ....................................... 4
Connecting the Speakers ............................................................ 5
Connecting Audio/Video Components ....................................... 6
Connecting the Power Cord ....................................................... 7
Basic Operations ......................................... 8
Turning On the Power ................................................................ 8
Selecting the Source to Play ....................................................... 8
Adjusting the Volume ................................................................. 9
Listening Only with Headphones ............................................... 9
Turning Off the Sounds Temporarily—Muting ........................ 10
Changing the Display Brightness ............................................. 10
Turning Off the Power with the Sleep Timer ........................... 10
Basic Settings ........................................... 11
Setting the Digital Input (DIGITAL IN) Terminals ................. 11
Selecting the Analog or Digital Input Mode ............................ 11
Setting the Speaker Information ............................................... 12
Sound Adjustments .................................... 15
Attenuating the Input Signal .................................................... 15
Adjusting the Front Speakers Output Balance ......................... 15
Adjusting the Tone ................................................................... 15
Adjusting the Subwoofer Output Level .................................... 15
Tuner Operations ....................................... 16
Tuning in Stations .................................................................... 16
Using Preset Tuning ................................................................. 16
Selecting the FM Reception Mode ........................................... 17
Creating Realistic Sound Fields ................... 18
About Relations between Speaker Layout and
Surround Modes ................................................................. 20
Using Dolby Pro Logic II, Dolby Digital and
DTS Digital Surround ........................................................ 21
Using DAP Modes and All Channel Stereo ............................. 23
Using DVD MULTI Playback Mode ................ 24
Activating DVD MULTI Playback Mode ................................ 24
COMPU LINK Remote Control System ......... 25
AV COMPU LINK Remote Control System .... 26
Operating JVC's Audio/Video
Components .......................................... 28
Operating Audio Components .................................................. 28
Operating Video Components .................................................. 29
Troubleshooting ......................................... 30
Specifications ............................................ 31
Remote
ONLY
This mark indicates that the remote control CAN
ONLY be used for the operation explained.
This mark indicates that the remote control CANNOT
Remote be used for the operation explained. Use buttons on
NOT
the front panel.
1
EN01-07.RX-6020V/6022V[J]_f
1
3/4/02, 4:23 PM
Parts Identification
Front Panel
2
3
FM/AM TUNING
FM/AM PRESET
1
45
7 89
6
p
RX-6020V AUDIO/VIDEO CONTROL RECEIVER
FM MODE
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
STANDBY
MEMORY
TUNED STEREO
SPK
L
C
R
AUTO MUTING SLEEP
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
VOLUME
MASTER VOLUME
S.WFR LFE
LS
S
RS
CH-
STANDBY/ON
SURROUND ON/OFF
INPUT ANALOG
INPUT DIGITAL
ADJUST SETTING
DVD MULTI
DVD
VCR
TV SOUND
CD
TAPE/CDR
FM
AM
INPUT ATT
SURROUND MODE
CONTROL
DOWN
UP
SPEAKERS ON/OFF
SOURCE NAME
PHONES
q
w e
r t y
u
i
o
* RX-6020VBK is used for front panel illustration throughout this instruction.
See page(s) in the parentheses for details.
Remote Control
A/V CONTROL
RECEIVER
STANDBY/ON
CENTER
AUDIO
TEST
1
1
3
2
EFFECT
REAR L
4
REAR R
7/P
8
ENTER
0
9
DVD
10
100
RETURN
q
VCR
SUBWOOFER
10
2
TV
6
5
MENU
Front Panel
SLEEP
SOUND
w
REW
FF
3
REC PAUSE
e
5
6
7
8
9
TAPE/CDR
CD
DVD
DVD MULTI
FM/AM
TV SOUND
VCR
ANALOG
/DIGITAL
r
FM MODE
ON/OFF
DIMMER TV/VIDEO SURROUND
MUTING
MODE
VCR CH
TV CH
VOLUME
p
t
y
u
i
TV VOLUME
REMOTE CONTROL RM- SRX6020J
y
u
i
o
CD–DISC
4
1
2
3
4
5
6
7
8
9
p
q
w
e
r
t
STANDBY/ON
button and STANDBY lamp (8)
FM/AM TUNING 5/∞ (up/down) buttons (16)
FM/AM PRESET 5/∞ (up/down) buttons (16, 17)
FM MODE button (17)
MEMORY button (16, 17)
Display (8)
ADJUST button (15, 22, 23, 24)
Remote sensor (3)
SETTING button (11 – 14)
MASTER VOLUME control (9)
PHONES jack (9)
SURROUND ON/OFF button (20 – 23)
SURROUND MODE button (20 – 23)
SPEAKERS ON/OFF button (9)
• INPUT ANALOG button (11)
• INPUT ATT button (15)
INPUT DIGITAL button (11, 12)
SOURCE NAME button (9)
Source selecting buttons (8, 9, 11, 16, 17, 24)
DVD MULTI, DVD, VCR, TV SOUND, CD, TAPE/CDR, FM, AM
CONTROL UP5/DOWN∞ buttons (11 – 15, 22 – 24)
Remote Control
1 • 10 keys for selecting preset channels (17)
• 10 keys for adjusting sound (15, 22, 23, 24)
• 10 keys for operating audio/video components (28, 29)
2 SOUND button (15, 22 – 24)
3 Operating buttons for audio/video components (25, 28, 29)
4 REC PAUSE button (28, 29)
5 Source selecting buttons (8, 9, 11, 17, 24, 27 – 29)
TAPE/CDR, CD, DVD, DVD MULTI, FM/AM, TV SOUND, VCR
6 FM MODE button (17)
7 DIMMER button (10)
8 TV/VIDEO button (29)
9 VCR CH (channel) +/– buttons (29)
p TV CH (channel) +/– buttons (29)
q STANDBY/ON
buttons (8, 26, 29)
AUDIO, TV, VCR, DVD
w SLEEP button (10)
e CD–DISC button (28)
r ANALOG/DIGITAL button (12)
t SURROUND ON/OFF and SURROUND MODE buttons
(20, 21, 23, 28)
y MUTING button (10)
u TV VOLUME +/– buttons (29)
i VOLUME +/– button (9)
2
EN01-07.RX-6020V/6022V[J]_f
2
3/4/02, 4:23 PM
Getting Started
General Precautions
• DO NOT insert any metal object to the unit.
• DO NOT disassemble the unit or remove screws, covers, or
cabinet.
• DO NOT expose the unit to rain or moisture.
Putting Batteries in the Remote Control
Before using the remote control, put two supplied batteries first.
• When using the remote control, aim the remote control directly at
the remote sensor on the unit.
1 On the back of the remote control, remove the
battery cover.
Locations
• Install the unit in a location that is level and protected from
moisture.
• The temperature around the unit must be between –5˚C and 35˚C
(23˚F and 95˚F).
• Make sure there is good ventilation around the unit. Poor
ventilation could cause overheating and damage the unit.
Handling the unit
• DO NOT touch the power cord with wet hands.
• DO NOT pull the power cord to unplug the cord. When
unplugging the cord, always grasp the plug so as not to damage
the cord.
• Keep the power cord away from the connecting cords and the
antenna. The power cord may cause noise or screen interference. It
is recommended to use a coaxial cable for antenna connection,
since it is well-shielded against interference.
• When a power failure occurs, or when you unplug the power cord,
the preset settings such as preset FM/AM channels and sound
adjustments may be erased in a few days.
2 Insert batteries.
• Make sure to match the polarity: (+) to (+) and (–) to (–).
Checking the Supplied Accessories
Check to be sure you have all of the following supplied accessories.
The number in the parentheses indicates the quantity of the piece(s)
supplied.
3 Replace the cover.
• Remote Control (1)
• Batteries (2)
• AM Loop Antenna (1)
• FM Antenna (1)
If anything is missing, contact your dealer immediately.
If the range or effectiveness of the remote control decreases, replace
the batteries. Use two R6P(SUM-3)/AA(15F) type dry-cell batteries.
CAUTION:
Follow these precautions to avoid leaking or cracking cells:
• Place batteries in the remote control so they match the polarity:
(+) to (+) and (–) to (–).
• Use the correct type of batteries. Batteries that look similar may
differ in voltage.
• Always replace both batteries at the same time.
• Do not expose batteries to heat or flame.
3
EN01-07.RX-6020V/6022V[J]_f
3
3/4/02, 4:23 PM
Parts Identification / Getting Started
Before Installation
Getting Started
Connecting the FM and AM Antennas
AM Loop Antenna
(supplied)
Outdoor FM antenna (not supplied)
If FM reception is poor, connect outdoor FM
antenna.
75
FMAXIAL
CO
Standard type
outdoor FM antenna
(not supplied)
Supplied FM
antenna
ANTENNA
75
FMAXIAL
or
CO
FM 75
COAXIAL
FM antenna (supplied)
Extend the supplied FM antenna horizontally.
Snap the tabs on the loop
into the slots of the base
to assemble the AM loop
antenna.
AM
LOOP
AM
EXT
If AM reception is poor, connect outdoor
single vinyl-covered wire (not supplied).
1
2
3
T
ON
F R KERS
EA FT
SP T LE
RIG
NA
TEN FM 75IAL
AN
AX
CO
AV LINK
U
MP
-4
CO
INK
U L O)
MP HR
CO(SYNC
DIO
AU LEFT
HT
RIG
CD
L2
ITA
DIG
T
ON
FR
) UT
( CD OEC)
(R E
TAPR
/CD
L IN
ITA
DIG
B
SUOFER
WO
INY)
(PLA
Connect the AM loop antenna supplied to the AM LOOP
terminals.
Turn the loop until you have the best reception.
• If the reception is poor, connect an outdoor single vinylcovered wire (not supplied) to the AM EXT terminal. (Keep
the AM loop antenna connected.)
+
–
–
–
–
AMP
O
LO
AM
EXIT
D
DV
R
VC
INY)
(PLA
EO
VID
HT
RIG
INY)
(PLA
D
UN
SO
TV
LEFT
+
R
REA
T
OU )
(REC
R
VC
AM loop antenna connection
R
T
IGH
H
T
OU )
(REC
TER
CEN
LEFT
S
+
+
OR
NIT
MOOUT
D
DV
L1
ITA )
DIG(DVD
TER
C E N KER
EA
SP
R
REA E R S
K
PEA
LEFT
HT
RIG UDIO
FER
OO
BW
SU OUT
A
FM antenna connection
Notes:
Connect the supplied FM antenna to the FM 75 Ω COAXIAL
terminal as temporary measure.
Extend the supplied FM antenna horizontally.
• If the reception is poor, connect an outdoor FM antenna (not
supplied). Before attaching a 75 Ω coaxial cable (with a
standard type connector), disconnect the supplied FM
antenna.
• If the AM loop antenna wire is covered with vinyl,
remove the vinyl while twisting it as shown to the right.
• Make sure antenna conductors do not touch any other
terminals, connecting cords and the power cord. This
could cause poor reception.
4
EN01-07.RX-6020V/6022V[J]_f
4
3/4/02, 4:23 PM
CE
AN
N : ED
TIO IMP
CAUAKER
SPE 16
8
After connecting the front, center, rear speakers and/or a subwoofer,
set the speaker setting information properly to obtain the best
possible surround effect. For details, see pages 12 to 14.
CAUTION:
Getting Started
Speaker layout diagram
Connecting the Speakers
“NO” for the subwoofer, “LARGE” for the front speakers,
and “SMALL” for the center and rear speakers are initial
settings. To get best possible sound, change the subwoofer
and speaker settings to fit your listening conditions (See
pages 12 and 13).
Use speakers with the SPEAKER IMPEDANCE indicated by the
speaker terminals.
Center
speaker
Connecting the front, center and rear speakers
1
2
Left front
speaker
3
Subwoofer
Right front
speaker
RX-6020V AUDIO/VIDEO CONTROL RECEIVER
1
FM/AM TUNING
FM/AM PRESET
FM MODE
STANDBY
MASTER VOLUME
MEMORY
STANDBY/ON
D I G I T A L
SURROUND
SURROUND ON/OFF
INPUT ANALOG
INPUT DIGITAL
ADJUST SETTING
DVD MULTI
DVD
VCR
TV SOUND
TAPE/CDR
FM
AM
INPUT ATT
SURROUND MODE
CONTROL
DOWN
UP
SPEAKERS ON/OFF
CD
SOURCE NAME
2
PHONES
Left rear
speaker
Right rear
speaker
For each speaker, connect the (+) and (–) terminals on the rear panel
to the (+) and (–) terminals marked on the speakers.
1 Cut, twist and remove the insulation at the end of
each speaker cord.
2 Open the terminal (1), then insert the speaker
cord (2).
3 Close the terminal.
T
FRONERS
T
SPEAKLEF
RIG
NA 75
TEN FM XIAL
AN
TER
CEN ER
SPEAK
COA
AV LINK
U
MP
K-4
CO
U LIN O)
MP HR
CO(SYNC
IO
AUD LEFT
Connecting the subwoofer speaker
)
L IN
ITA
DIG
T
ON
FR
TER
CEN
IN
AY)
(PL
R
SUB
OFE
WO
T
LEF
HT
+
–
ION
CAUT ER
SPEAK
8
:
CE
EDAN
IMP
16
–
AM
EXIT
AMP
LOO
IN
AY)
(PL
EO
VID
D
UN
HT
SO
RIG
T
LEF
FER
OO
BW
SU OUT
IO
AUD
FER
OO
BW
SU OUT
To
subwoofer
AUDIO
RIGHT
–
HT
RIG
R
VC
By connecting a powered subwoofer, you can enhance the bass or
reproduce
the original LFE signals recorded in the digital software.
+
R
REA
T
OUC)
(RE
IN
AY)
(PL
TV
–
R
VC
D
DV
T
OUC)
(RE E
TAPR
/CD
+
T
OUC)
(RE
HT
RIG
CD
( CD
HT
+
OR
NIT
MOOUT
D
DV
L1
ITA
DIG(DVD)
L2
ITA
DIG
REARERS
T
SPEAK
LEF
RIG
LEFT
FRONT
DVD
Powered subwoofer
SUB
WOOFER
CENTER
NT
FROKERS
EA FT
SP T LE
REAR
RIG
RIGHT
LEFT
TER
CEN KER
EA
SP
SUBWOOFER
OUT
R
REAERS
K
PEA T
S
RIG
HT
LEF
+
–
H
+
–
–
CE
AN
N : ED
TIO IMP
CAUAKER
SPE
8
16
To left
front speaker
+
–
Connect the input jack of a powered subwoofer to the
SUBWOOFER OUT jack on the rear panel, using a cable with RCA
pin plugs (not supplied).
• Refer also to the manual supplied with your subwoofer.
+
To left
rear speaker
To center speaker
To right front speaker
Since bass sound is non-directional, you can place a powered
subwoofer wherever you like. Normally place it in front of
you.
To right rear speaker
5
EN01-07.RX-6020V/6022V[J]_f
5
3/4/02, 4:24 PM
Getting Started
Connecting Audio/Video Components
Video component connections
Use the cables with RCA pin plugs (not supplied).
Connect the white plug to the audio left jack, the red plug to the
audio right jack, and the yellow plug to the video jack.
Turn off all components before connecting.
Analog connections
Audio component connections
Use the cables with RCA pin plugs (not supplied).
Connect the white plug to the audio left jack, and the red plug to the
audio right jack.
TV
CD
TV
CAUTION:
If you connect a sound-enhancing device such as a graphic equalizer
between the source components and this receiver, the sound output
through this receiver may be distorted.
OUT
(REC)
MONITOR
OUT
IN
(PLAY)
DVD
OUT
(REC)
OUT
(REC)
TAPE
CDR
To audio
output
CD player
CD player
CD
VCR
VCR
IN
(PLAY)
IN
(PLAY)
RIGHT
OUT
(REC)
LEFT
AUDIO
TAPE
CDR
To audio output
VIDEO
TV SOUND
To video input
IN
(PLAY)
Connect the TV to the MONITOR OUT jack to view
the playback picture from the other connected video
components.
Cassette deck or CD recorder
Cassette deck
To audio input
VCR
To audio output
PHONO
C
VCR
A
CD
CD
OUT
(REC)
D
B
TAPE
CDR
IN
(PLAY)
CD
OUT
(REC)
OUT
(REC)
MONITOR
OUT
VCR
TAPE
CDR
IN
(PLAY)
IN
(PLAY)
DVD
TV SOUND
OUT
(REC)
OUT
(REC)
VCR
VCR
IN
(PLAY)
IN
(PLAY)
RIGHT
LEFT
AUDIO
VIDEO
TV SOUND
To audio input
RIGHT
To audio output
CD recorder
Note:
You can connect either a cassette deck or a CD recorder to the TAPE/
CDR jacks. When connecting a CD recorder to the TAPE/CDR jacks,
change the source name to “CDR”, which will be shown on the display
when selected as the source. See page 9 for details.
LEFT
AUDIO
Å
ı
Ç
Î
To left/right channel audio output
To left/right channel audio input
To video output
To video input
If your audio components have a COMPU LINK jack
See also page 25 for detailed information about the connection and
the COMPU LINK remote control system.
6
EN01-07.RX-6020V/6022V[J]_f
6
3/4/02, 4:24 PM
IMPORTANT:
DVD player
A
• When connecting the DVD player or digital TV to the digital terminal,
you also need to connect it to the video jack on the rear. Without
connecting it to the video jack, you cannot view any playback
picture.
• After connecting the components to the DIGITAL IN terminals, make
sure the following if necessary:
– Set the digital input terminal setting correctly. For details, see
“Setting the Digital Input (DIGITAL IN) Terminals” on page 11.
– Select the digital input mode correctly. For details, see “Selecting
the Analog or Digital Input Mode” on page 11.
B
DVD
MONITOR
OUT
AUDIO
RIGHT
LEFT
FRONT
DVD
DVD
SUB
WOOFER
Digital TV
OUT
(REC)
CENTER
VCR
REAR
DVD player
IN
(PLAY)
RIGHT
LEFT
VIDEO
DVD
SUBWOOFER
OUT
CD player
CD recorder
Å To front left/right channel audio output (or to audio mixed
output)
ı To video output
Note:
To enjoy the software encoded with Dolby Digital or DTS Digital
Surround, you must connect the DVD player using the digital terminal
on the rear of this receiver. (See “Digital connections” below.)
For enjoying DVD MULTI Playback Mode—
• When you connect the DVD player with its analog discrete output
(5.1 CH reproduction) jacks:
B
A
When the component has a digital coaxial
output terminal, connect it to the DIGITAL
1 (DVD) terminal, with the digital coaxial
cable (not supplied).
When the component has a digital optical
output terminal, connect it to the DIGITAL
2 (CD) terminal, with the digital optical
cable (not supplied).
Before connecting a digital
optical cable, unplug the
protective plug.
DVD player
DIGITAL 1
(DVD)
DIGITAL 2 ( CD )
DIGITAL IN
DVD
E
C
D
Notes:
MONITOR
OUT
AUDIO
RIGHT
LEFT
FRONT
DVD
DVD
SUB
WOOFER
OUT
(REC)
CENTER
VCR
REAR
IN
(PLAY)
RIGHT
LEFT
VIDEO
SUBWOOFER
OUT
Å
ı
Ç
Î
‰
To rear left/right channel audio output
To center channel audio output
To subwoofer audio output
To front left/right channel audio output
To video output
Digital connections
• When shipped from the factory, the DIGITAL IN terminals have
been set for use with the following components:
– DIGITAL 1 (coaxial): For DVD player
– DIGITAL 2 (optical): For CD player
• When you want to operate the CD player or CD recorder using the
COMPU LINK remote control system, connect the target
component also as described in “Analog connections” (see page 6).
Connecting the Power Cord
Before plugging the power cord into an AC outlet, make sure that all
connections have been made.
Plug the power cord into an AC outlet.
CAUTIONS:
• Do not touch the power cord with wet hands.
• Do not pull on the power cord to unplug the cord. When
unplugging the cord, always grasp the plug so as not to damage
the cord.
This receiver is equipped with two DIGITAL IN terminals—one
digital coaxial terminal and one digital optical terminal.
You can connect any component to one of the digital terminals using
a digital coaxial cable (not supplied) or digital optical cable (not
supplied).
EN01-07.RX-6020V/6022V[J]_f
7
7
3/4/02, 4:24 PM
Getting Started
DVD player
Basic Operations
Front Panel
Remote Control
STANDBY lamp
Display
A/V CONTROL
RECEIVER
STANDBY/ON
CENTER
AUDIO
TEST
1
REAR L
EFFECT
RX-6020V AUDIO/VIDEO CONTROL RECEIVER
4
FM/AM TUNING
FM/AM PRESET
REAR R
7/P
FM MODE
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
MEMORY
TUNED STEREO
SPK
L
C
R
S
VOLUME
10
MASTER VOLUME
RS
INPUT ANALOG
INPUT DIGITAL
DVD MULTI
DVD
VCR
TV SOUND
CD
TAPE/CDR
FM
AM
Source
selecting
buttons
DIMMER
CONTROL
DOWN
UP
SPEAKERS ON/OFF
SOURCE NAME
PHONES
STANDBY/ON
MASTER
VOLUME
SOURCE Source
selecting
NAME
buttons
Turning On the Power
Press STANDBY/ON
remote control).
FF
SLEEP
CD–DISC
TAPE/CDR
CD
DVD
DVD MULTI
FM/AM
TV SOUND
VCR
ANALOG
/DIGITAL
FM MODE
ON/OFF
DIMMER TV/VIDEO SURROUND
MUTING
MODE
VCR CH
PHONES SPEAKERS
jack
ON/OFF
SLEEP
REC PAUSE
ADJUST SETTING
INPUT ATT
SURROUND MODE
DVD
100
SOUND
REW
SURROUND ON/OFF
STANDBY/
ON
AUDIO
10
0
RETURN
CH-
STANDBY/ON
VCR
9
8
SUBWOOFER
ENTER
AUTO MUTING SLEEP
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
S.WFR LFE
LS
TV
6
5
MENU
STANDBY
3
2
TV CH
TV VOLUME
VOLUME
MUTING
VOLUME
+/–
REMOTE CONTROL RM-SRX6020J
Selecting the Source to Play
(or STANDBY/ON
AUDIO on the
Press one of the source selecting buttons.
The selected source name appears on the display.
STANDBY/ON
STANDBY
AUDIO
DVD MULTI
DVD
VCR
TV SOUND
TAPE/CDR
CD
DVD
CD
TAPE/CDR
FM
AM
FM/AM
TV SOUND
VCR
STANDBY/ON
On the front panel
From the remote control
DVD MULTI
SOURCE NAME
The STANDBY lamp goes off. The name of the current source (or
station frequency) appears on the display.
On the front panel
From the remote control
Current source name appears
DVD MULTI
ANALOG
SPK
L
C
R
VOLUME
S.WFR LFE
LS
S
RS
CH-
Current volume level is shown here
To turn off the power (into standby mode)
(or
Press STANDBY/ON
AUDIO on the remote control)
STANDBY/ON
again.
The STANDBY lamp lights up.
STANDBY
STANDBY/ON
NOTE:
A small amount of power is consumed in standby mode. To turn the
power off completely, unplug the AC power cord.
: Select the DVD player for viewing the digital video
disc using the analog discrete output mode (5.1 ch
reproduction).
To enjoy the DVD MULTI playback, see page 24.
DVD
: Select the DVD player.
VCR
: Select the VCR.
TV SOUND : Select the TV sound.
CD *
: Select the CD player.
TAPE/CDR * : Select the cassette deck (or the CD recorder).
FM and AM (FM/AM) *
: Select an FM or AM broadcast.
• Each time you press FM/AM on the remote
control, the band alternates between FM and AM.
Notes:
• When connecting a CD recorder (to the TAPE/CDR jacks), change
the source name that appears on the display. See page 9 for
details.
• When you have connected some digital source components using
digital terminals (see page 7), you need to select the digital input
mode (see page 11).
• When you press one of the source selecting buttons on the remote
control marked above with an asterisk (*), the receiver
automatically turns on.
8
EN08-17.RX-6020V/6022V[J]_f
8
3/4/02, 4:24 PM
Remote
NOT
When you connect the CD recorder to the
TAPE/CDR jacks on the rear panel, change the
source name shown on the display.
1 Press TAPE/CDR (SOURCE NAME).
TAPE/CDR
• Make sure “TAPE” appears on the display.
SOURCE NAME
2 Press and hold SOURCE NAME (TAPE/CDR)
Adjusting the Volume
On the front panel:
Basic Operations
Changing the source name
MASTER VOLUME
To increase the volume, turn MASTER
VOLUME clockwise.
To decrease the volume, turn it
counterclockwise.
From the remote control:
until “ASSIGN CDR” appears on the display.
To increase the volume, press VOLUME +.
To decrease the volume, press VOLUME –.
To change the source name from “CDR” to “TAPE,” repeat the
same procedure above (in step 1, make sure “CDR” appears on the
display).
Note:
Without changing the source name, you can still use the connected
component. However, there may be some inconvenience:
– “TAPE” will appear on the display when you select the CD
recorder.
– You cannot use the digital input (see page 11) for the CD recorder.
– You cannot use the COMPU LINK remote control system (see page
25) to operate the CD recorder.
Selecting different sources for each picture and
sound
You can watch picture from a video component while listening to
sound from another component.
VOLUME
CAUTION:
Always set the volume to the minimum before starting any source. If
the volume is set at its high level, the sudden blast of sound energy
can permanently damage your hearing and/or ruin your speakers.
Note:
The volume level can be adjusted within the range from “0” (minimum)
to “50” (maximum).
Listening Only with Headphones
Remote
NOT
You must turn off speakers when you listen with headphones.
1 Connect a pair of headphones to the PHONES jack on the front
Press one of the audio source selecting buttons—CD, TAPE/CDR,
FM, AM (FM/AM), while viewing the picture from a video
component such as the VCR or DVD player, etc.
CD
TAPE/CDR
FM
AM
TAPE/CDR
CD
DVD
FM/AM
TV SOUND
VCR
DVD MULTI
panel.
2 Press SPEAKERS ON/OFF.
• “HEADPHONE” appears for a while and the H. PHONE
indicator lights up on the display.
The H. PHONE indicator lights up.
SOURCE NAME
ANALOG
L
On the front panel
R
H.PHONE
From the remote control
Note:
Once you have selected a video source, pictures of the selected
source are sent to the TV until you select another video source.
This cancels the Surround mode currently selected, and activates
the HEADPHONE mode (see below).
HEADPHONE mode:
When using the headphones, following signals are output
regardless of your speaker setting:
— For 2 channel sources, the front left and right channel signals
are output directly from the headphones.
— For multichannel sources, the front left, right, center, and rear
channel signals are down-mixed and then output from the
headphones.
You can enjoy multichannel sound sources using the
headphones.
CAUTION:
Be sure to turn down the volume:
• Before connecting or putting on headphones, as high volume can
damage both headphones and your hearing.
• Before turning on speakers again, as high volume may output from
the speakers.
9
EN08-17.RX-6020V/6022V[J]_f
9
3/4/02, 4:24 PM
Basic Operations
Turning Off the Sounds
Temporarily—Muting
Remote
ONLY
You can mute the sound temporarily.
Press MUTING on the remote control to mute
the sound through all speakers or headphones
connected.
• “MUTING” appears on the display and the volume
turns off (the volume level indicator goes off).
When you change the source, the memorized settings for the newly
selected source are automatically recalled.
Following can be stored for each source:
• Input attenuator mode (see page 15)
• Balance (see page 15)
• Tone adjustment (see page 15)
• Subwoofer output level (see page 15)
• Surround mode selection (see page 21-23)
L
C
R
S.WFR LFE
S
LS
This receiver memorizes sound settings for each source when:
• Turning off the power,
• Changing the source, and
• Assigning the source name.
MUTING
SPK
ANALOG
Basic adjustment auto memory
RS
CH-
Notes:
To restore the sound, press MUTING again.
• Turning MASTER VOLUME on the front panel or pressing
VOLUME +/– on the remote control also restores the sound.
• You cannot assign and store different settings for digital input mode
and analog input mode.
• If the source is FM or AM, you can assign a different setting for
each band.
For recording
Remote
ONLY
Changing the Display Brightness
You can dim the display.
Press DIMMER on the remote control .
• Each time you press the button, the display dims and
brightens alternately.
DIMMER
You can record any source playing through the receiver to a cassette
deck (or a CD recorder) connected to the TAPE/CDR jacks and the
VCR connected to the VCR jacks at the same time.
While recording, you can listen to the selected sound source at
whatever sound level you like without affecting the sound levels of
the recording.
Note:
Turning Off the Power
with the Sleep Timer
Remote
ONLY
You can fall asleep while listening to music—Sleep Timer.
Press SLEEP on the remote control repeatedly.
• The SLEEP indicator lights up on the display, and the
shut-off time changes in 10 minutes intervals.
ANALOG
SPK
L
C
S
Signal indicators
L
C
R
S.WFR LFE
LS
S
Speaker indicators
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
RS
SPK
L
C
ONE TOUCH
R
S.WFR LFE
LS
S
RS
CH-
PRO LOGIC ΙΙ
L
C
S.WFR LFE
LS
S
RS
R
RS
20
30
40
50
60
0 (Canceled)
90
80
70
When the shut-off time comes
The receiver turns off automatically.
To check or change the time remaining before the shut-off time
Press SLEEP once.
The remaining time (in minutes) until the shut-off time appears.
• To change the shut-off time, press SLEEP repeatedly until
preferred remaining time appears on the display.
To cancel the Sleep Timer
Press SLEEP repeatedly until “SLEEP 0 MIN” appears on the
display. (The SLEEP indicator goes off.)
• Turning off the power also cancels the Sleep Timer.
The following signal indicators light up—:
L : • When digital input is selected: Lights up when the left
channel signal comes in.
• When analog input is selected: Always lights up.
R : • When digital input is selected: Lights up when the right
channel signal comes in.
• When analog input is selected: Always lights up.
C : When the center channel signal comes in.
LS : When the left rear channel signal comes in.
RS : When the right rear channel signal comes in.
S : When the monaural rear channel signal or 2 ch Dolby
Surround encoded signal comes in.
LFE: When the LFE channel signal comes in.
The speaker indicators light up when both of the following
conditions are satisfied:
• The corresponding speaker is activated, and
• The corresponding speaker is required for the current playback.
Notes:
• When you select “DVD MULTI,” all signal indicators except “S” light
up.
• When “SUBWOOFER” is set to “YES” (see page 12),
up.
10
EN08-17.RX-6020V/6022V[J]_f
R
SLEEP
CH-
10
Signal and speaker indicators on the display
SLEEP
S.WFR LFE
LS
The output level, tone adjustment (see page 15), and Surround
modes (see page 21-23) cannot affect the recording.
10
3/4/02, 4:24 PM
S.WFR
lights
Basic Settings
Remote Control
Display
A/V CONTROL
RECEIVER
STANDBY/ON
CENTER
AUDIO
TEST
1
REAR L
EFFECT
4
RX-6020V AUDIO/VIDEO CONTROL RECEIVER
FM/AM PRESET
MEMORY
TUNED STEREO
SPK
L
C
R
AUTO MUTING SLEEP
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
SUBWOOFER
10
VOLUME
MASTER VOLUME
S.WFR
LS
S
100
REW
INPUT ANALOG
INPUT DIGITAL
Source
selecting
buttons
ADJUST SETTING
DVD MULTI
DVD
VCR
TV SOUND
INPUT ATT
SURROUND MODE
CONTROL
DOWN
UP
SPEAKERS ON/OFF
CD
SLEEP
SOUND
CH-
SURROUND ON/OFF
DVD
10
0
RETURN
RS
VCR
9
8
ENTER
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
STANDBY
STANDBY/ON
TV
REAR R
7/P
FM MODE
6
5
MENU
FM/AM TUNING
3
2
TAPE/CDR
FM
AM
SOURCE NAME
FF
REC PAUSE
CD–DISC
TAPE/CDR
CD
FM/AM
TV SOUND
DVD
DVD MULTI
VCR
ANALOG
/DIGITAL
FM MODE
ON/OFF
PHONES
DIMMER TV/VIDEO SURROUND
ANALOG/
DIGITAL
MUTING
MODE
VCR CH
INPUT
INPUT
ANALOG DIGITAL
Source
selecting
buttons
TV CH
TV VOLUME
VOLUME
SETTING
REMOTE CONTROL RM -SRX6020J
CONTROL
UP 5/DOWN ∞
Setting the Digital Input
[DIGITAL IN] Terminals
Remote
NOT
Selecting the Analog or Digital Input
Mode
When you use the digital input terminals, register what components
are connected to which terminals (DIGITAL 1/2) so that the correct
source name will appear when you select the digital source.
When you have connected digital source components using both the
analog connections (see page 6) and the digital connections (see
page 7) methods, you need to select the input mode correctly.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
1
1
Press SETTING repeatedly until
“DIGITAL IN” appears on the display.
Press one of the source selecting buttons—DVD,
TV SOUND, CD, or TAPE/CDR*—for which you
want to change the input mode.
SETTING
DVD MULTI
Then the display changes to show the current setting.
CD
DIGITAL 2 terminal setting
DVD
VCR
TV SOUND
TAPE/CDR
FM
AM
TAPE/CDR
CD
DVD
FM/AM
TV SOUND
VCR
DVD MULTI
SOURCE NAME
S.WFR LFE
LS
S
RS
On the front panel
CH-
DIGITAL 1 terminal setting
Note:
* Among the sources listed above, you can select the digital input
only for the sources which you have selected the digital input
terminals for. (See “Setting the Digital Input (DIGITAL IN)
Terminals” on the left column.)
* “1DVD 2CD” is the initial setting. If you have already
changed the setting, another combination will be shown.
2
Press CONTROL UP 5/DOWN ∞ to
select the appropriate digital terminal
setting.
CONTROL
DOWN
UP
• Each time you press the button, the display
changes as follows:
1 DVD 2 CD j 1 DVD 2 TV j
1 CD 2 DVD j 1 CD 2 TV j
1 TV 2 DVD j 1 TV 2 CD j
1 CDR 2 DVD j 1 CDR 2 CD j
(back to the beginning)
From the remote control
1 DVD 2 CDR j
1 CD 2 CDR j
1 TV 2 CDR j
1 CDR 2 TV j
2
Select digital input mode.
On the front panel:
Press INPUT DIGITAL.
INPUT DIGITAL
“DIGITAL AUTO” appears on the display and
the indicator for the detected signals also lights
up.
SPK
DIGITAL AUTO
LINEAR PCM
L
R
S.WFR
S
CH-
Ex: With the incoming signals of Linear PCM
Note:
When shipped from the factory, the DIGITAL IN terminals can be used
as the digital input for the following components:
–DIGITAL 1 (coaxial): For DVD player
–DIGITAL 2 (optical): For CD player
To change the input mode back to analog
input, press INPUT ANALOG.
“ANALOG” appears on the display and the
analog indicator also lights up.
INPUT ANALOG
INPUT ATT
TO BE CONTINUED ON THE NEXT PAGE
EN08-17.RX-6020V/6022V[J]_f
11
3/4/02, 4:24 PM
11
Basic Operations / Basic Settings
Front Panel
Basic Settings
From the remote control:
ANALOG
/DIGITAL
Press ANALOG/DIGITAL.
The current setting indication appears on the display.
• Each time you press the button, the input mode alternates
between the analog input (“ANALOG”) and the digital input
(“DIGITAL AUTO”).
DIGITAL AUTO : Select this for the digital input mode. The
receiver automatically detects the
incoming signal format. (The DIGITAL
AUTO indicator lights up on the display,
then the digital signal indicator for the
detected signals lights up.)
ANALOG
: Select this for the analog input mode.
(Initial setting when shipped from the
factory.)
If the following symptoms occur while playing Dolby Digital or
DTS Digital Surround software with “DIGITAL AUTO”
selected, follow the procedure below:
– Sound does not come out at the beginning of playback.
– Noise comes out while searching or skipping chapters or tracks.
1 Press INPUT DIGITAL (or ANALOG/DIGITAL on the remote
control).
“DIGITAL AUTO” appears on the display.
ANALOG
/DIGITAL
INPUT DIGITAL
On the front panel
From the remote control
2 Press CONTROL UP 5/DOWN ∞ to select
“DOLBY DIGITAL” or “DTS SURROUND”
while “DIGITAL AUTO” still remains on the
display.
• Each time you press the button, the digital input
mode changes as follows:
Remote
NOT
CONTROL
DOWN
UP
When “DOLBY DIGITAL” or “DTS
SURROUND” is selected, “DIGITAL AUTO” goes off.
The following are the analog/digital signal indicators on the display to
indicate what type of the signal comes into the receiver.
ANALOG
: Lights when the analog input is selected.
LINEAR PCM : Lights when Linear PCM signals come in.
DIGITAL : • Lights when Dolby Digital signals come in.
• Flashes when “DOLBY DIGITAL” is
selected for software not encoded with Dolby
Digital signals.
: • Lights when DTS signals come in.
• Flashes when “DTS SURROUND” is
selected for software not encoded with DTS
signals.
Note:
When “DIGITAL AUTO” cannot recognize the incoming signals, no
digital signal indicator lights up on the display.
Setting the Speaker Information
Remote
NOT
To obtain the best possible sound or effect from Surround modes
(see page 21-23), register the following speakers and subwoofer
information after all connections are completed.
The following are items you can set:
• Subwoofer information—SUBWOOFER
• Speaker size—FRNT SP, CNTR SP, REAR SP
• Speaker distance—UNIT, FRNT DIS, CNTR DIS, REAR DIS
• Crossover frequency—CROSS
• Low frequency effect attenuator—LFE ATT
• Dynamic range compression—D. COMP
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
“NO” for the subwoofer, “LARGE” for the front speakers,
and “SMALL” for the center and rear speakers are initial
settings. To get best possible sound, change the subwoofer and
speaker settings to fit your listening conditions.
SPK
DIGITAL AUTO
L
C
R
S.WFR LFE
DIGITAL
LS
S
RS
Subwoofer information
CH-
Register whether you have connected a subwoofer or not.
DIGITAL AUTO
DTS SURROUND
DOLBY DIGITAL
• To play back software encoded with Dolby Digital, select
“DOLBY DIGITAL.”
• To play back software encoded with DTS Digital Surround,
select “DTS SURROUND.”
Note:
When you turn off the power or select another source, “DOLBY
DIGITAL” and “DTS SURROUND” are canceled and the digital input
mode is automatically reset to “DIGITAL AUTO.”
1
Press SETTING repeatedly until
“SUBWOOFER” (with the current
setting) appears on the display.
2
Press CONTROL UP 5/DOWN ∞
to register whether you have
connected a subwoofer or not.
12
CONTROL
DOWN
UP
• Each time you press the button, the
subwoofer setting alternates between “YES” and “NO.”
YES
: Select this when you have connected a subwoofer.
You can adjust the subwoofer output level
(see page 15).
NO
: Select this when you have not connected or have
disconnected a subwoofer.
12
EN08-17.RX-6020V/6022V[J]_f
T SETTING
3/4/02, 4:24 PM
Speaker distance
Register the sizes of all the connected speakers.
• When you change your speakers, register the information about the
speakers again.
Register the unit you use, then the speaker distance from your
listening point.
• If you have set the unit before, start from step 3.
• Speaker distance is not valid for the DVD MULTI playback mode.
1
2
T SETTING
Press SETTING repeatedly until
“FRNT SP (Front speaker),” “CNTR
SP (Center speaker),” or “REAR SP
(Rear speaker)” (with the current setting)
appears on the display.
Press CONTROL UP 5/DOWN ∞ to
select the appropriate item about the
speaker selected in the above step.
CONTROL
DOWN
UP
1
* “METER” is the initial setting. If you have already changed the
setting, “FEET” will be shown.
2
SMALL
FEET
3
SMALL : Select this when the speaker size is relatively small.
(See “Notes” below.)
NONE
3
: Select this when you have not connected a speaker.
(Not selectable for the front speakers)
4
• Keep the following comment in mind as reference when adjusting.
– If the size of the cone speaker unit built in your speaker is greater
than 12 cm (4 3/4 inches), select “LARGE,” and if it is smaller than
12 cm (4 3/4 inches), select “SMALL.”
• If you have selected “NO” for the subwoofer setting, you can only
select “LARGE” for the front speaker setting.
• If you have selected “SMALL” for the front speaker setting, you
cannot select “LARGE” for the center and rear speaker settings.
: Speaker distance is shown in feet.
SETTING
Press SETTING repeatedly until
“FRNT DIS (Front distance),” “CNTR
DIS (Center distance),” or “REAR DIS
(Rear distance)” (with the current setting)*
appears on the display.
• The display shows the current setting in the unit selected in
step 2.
* “3.0m” is the initial setting for meter and “10FT” is for feet. If
you have already changed the setting, another value will be
shown.
Repeat step 1 and 2 to select the appropriate
items for other speakers.
Notes:
CONTROL
DOWN
UP
METER : Speaker distance is shown in meter.
NONE
LARGE : Select this when the speaker size is relatively large.
(See “Notes” below.)
Press CONTROL UP 5/DOWN ∞ to
select the unit.
• Each time you press the button, the setting
alternates between “METER” and “FEET.”
• Each time you press the button, the display
changes as follows:
LARGE
SETTING
Press SETTING repeatedly until
“UNIT” (with the current setting)*
appears on the display.
Press CONTROL UP 5/DOWN ∞
to select the appropriate speaker
distance.
CONTROL
DOWN
UP
• If you have selected “METER” in step 2, the
value is changed from “0.3m” to “9.0m” by 0.3 m step.
• If you have selected “FEET” in step 2, the value is changed
from “1FT” to “30FT” by 1 foot step.
Left front
speaker
Center speaker
Right front
speaker
3.0 m
(10 feet)
2.7 m
(9 feet)
2.4 m
(8 feet)
2.1 m
(7 feet)
Left rear
speaker
Right rear
speaker
Example: In this case,
set “FRNT DIS” to “3.0m” or “10FT,”
set “CNTR DIS” to “2.7m” or “9FT” and,
set “REAR DIS” to “2.4m” or “8FT.”
Note:
If you have selected “NONE” for the center and rear speakers
setting, you cannot set the speaker distance for the center and rear
speakers.
13
EN08-17.RX-6020V/6022V[J]_f
13
3/4/02, 4:24 PM
Basic Settings
Speaker size
Basic Settings
Crossover frequency
Dynamic range compression
Small speakers cannot reproduce the bass sounds efficiently. If you
use a small speaker in any position, this receiver automatically
reallocates the bass sound elements assigned from small speakers to
large speakers.
To use this function properly, set this crossover frequency level
according to the size of the small speaker connected.
• If you have selected “LARGE” for all speakers, this function will
not take effect.
• Crossover frequency is not valid for DVD MULTI playback mode
and HEADPHONE mode.
You can compress the dynamic range (difference between maximum
sound and minimum sound) of the reproduced sound. This is useful
when enjoying surround sound at night.
• This function takes effect only when playing back a source
encoded with Dolby Digital.
1
Press SETTING repeatedly until “CROSS
(Crossover)” (with the current setting)*
appears on the display.
Press CONTROL UP 5/DOWN ∞ to
select the crossover frequency level you
like to use.
CONTROL
DOWN
UP
Press SETTING repeatedly until
“D. COMP (Dynamic range
compression)” (with the current setting)*
appears on the display.
2
Press CONTROL UP 5/DOWN ∞
to select the appropriate compression
level.
100HZ
200HZ
MAX
OFF : Select this when you want to enjoy surround with its
full dynamic range. (No effect applied.)
120HZ
150HZ
MID
If the bass sound is distorted while playing back software using
Dolby Digital or DTS Digital Surround, follow the procedure
below:
• Low frequency effect attenuator is not valid for the DVD MULTI
playback mode.
• This function takes effect only when the subwoofer (LFE) signals
come in, (with “SUBWOOFER” set to “YES”).
Press SETTING repeatedly until “LFE
ATT (Low Frequency Effect Attenuator)”
(with the current setting)* appears on the
display.
: Select this when you want to reduce the dynamic range
a little.
MAX : Select this when you want to apply the compression
effect fully. (Useful at night.)
SETTING
* “0dB” is the initial setting. If you have already changed the
setting, “–10dB” will be shown.
2
Press CONTROL UP 5/DOWN ∞ to
select the low frequency effect
attenuator level.
CONTROL
DOWN
UP
• Each time you press the button, the setting
alternates between “0dB” and “–10dB.”
0dB
–10dB
: Normally select this.
: Select this when the bass sound is distorted.
14
EN08-17.RX-6020V/6022V[J]_f
14
MID
OFF
Low frequency effect attenuator
1
CONTROL
DOWN
UP
• Each time you press the button, the display changes
as follows:
• Each time you press the button, the crossover
frequency level changes as follows:
80HZ
SETTING
* “MID” is the initial setting. If you have already changed the
setting, another setting will be shown.
SETTING
* “100HZ” is the initial setting. If you have already changed the
setting, another frequency will be shown.
2
1
3/4/02, 4:24 PM
Sound Adjustments
Display
A/V CONTROL
RECEIVER
STANDBY/ON
CENTER
AUDIO
TEST
1
REAR L
4
SUBWOOFER +/–
RX-6020V AUDIO/VIDEO CONTROL RECEIVER
FM MODE
REAR R
7/P
8
MEMORY
TUNED STEREO
SPK
L
C
R
10
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
VOLUME
MASTER VOLUME
S.WFR LFE
LS
S
SOUND
AUTO MUTING SLEEP
VCR
9
SUBWOOFER
ENTER
0
DVD
10
100
RETURN
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
STANDBY
TV
6
5
MENU
FM/AM PRESET
3
2
EFFECT
FM/AM TUNING
Basic Settings / Sound Adjustments
Remote Control
Front Panel
SLEEP
SOUND
REW
FF
RS
CH-
STANDBY/ON
REC PAUSE
SURROUND ON/OFF
INPUT ANALOG
INPUT DIGITAL
DVD MULTI
DVD
VCR
TV SOUND
CD
TAPE/CDR
FM
AM
INPUT ATT
SURROUND MODE
CD–DISC
TAPE/CDR
CD
FM/AM
TV SOUND
DVD
DVD MULTI
VCR
ANALOG
/DIGITAL
ADJUST SETTING
CONTROL
DOWN
UP
SPEAKERS ON/OFF
FM MODE
ON/OFF
DIMMER TV/VIDEO SURROUND
SOURCE NAME
MUTING
MODE
PHONES
VCR CH
TV CH
TV VOLUME
VOLUME
REMOTE CONTROL RM - SRX6020J
INPUT ATT
ADJUST
CONTROL
UP 5/DOWN ∞
Once each of following settings has been adjusted, this receiver
memorizes the adjustments for each source.
1
Remote
NOT
Attenuating the Input Signal
Press and hold INPUT ATT (INPUT
ANALOG) so that the INPUT ATT
indicator lights up on the display.
ADJUST
* “0” is the initial setting. If you have already changed the
setting, another number (level) will be shown.
When the input level of the analog source is too high, sounds will
be distorted. If this happens, you need to attenuate the input signal
level to prevent the sound distortion.
1
Press ADJUST repeatedly until “BASS”
or “TREBLE” (with the current setting)*
appears on the display.
BASS
: To adjust the bass (–10 to +10).
TREBLE : To adjust the treble (–10 to +10).
INPUT ANALOG
INPUT ATT
2
Press CONTROL UP 5/DOWN ∞ to
adjust the bass or treble sound level.
CONTROL
DOWN
UP
• Each time you press the button, the sound
level changes by ±2 steps.
• Each time you press and hold the button, the Input Attenuator
mode turns on (“INPUT ATT ON”) or off (“INPUT
NORMAL”).
Note:
When selecting “DVD MULTI” as the source, this effect does not work.
Adjusting the Front Speakers
Output Balance
Remote
NOT
If the sounds you hear from the front right and left speakers are
unequal, you can adjust the speaker output balance.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
1
Press ADJUST repeatedly until
“BALANCE” (with the current setting)*
appears on the display.
Press CONTROL UP 5/DOWN ∞
to adjust the balance.
On the front panel:
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
1
Press ADJUST repeatedly until
“SUBWFR (Subwoofer)” (with the
current setting)* appears on the display.
ADJUST
* “0” is the initial setting. If you have already changed the
setting, another number (level) will be shown.
2
CONTROL
DOWN
UP
• Pressing CONTROL UP 5 decreases the
left channel output from “CNTR (Center)”
to “L–21.”
• Pressing CONTROL DOWN ∞ decreases
the right channel output from “CNTR (Center)” to “R–21.”
Adjusting the Tone
You can adjust the subwoofer output level if you have connected a
subwoofer and set the subwoofer information correctly—“YES.”
ADJUST
* “CNTR (Center)” is the initial setting. If you have already
changed the setting, another setting will be shown.
2
Adjusting the Subwoofer Output Level
Remote
NOT
You can adjust the bass and treble sounds as you like.
Before you start , remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
Press CONTROL UP 5/DOWN ∞ to
adjust the subwoofer output level
(–10 to +10).
CONTROL
DOWN
UP
From the remote control:
1
SOUND
Press SOUND.
10 keys are activated for sound adjustments.
2
Press SUBWOOFER +/– to adjust
the subwoofer output level
(–10 to +10).
SUBWOOFER
0
10
100
Note:
Subwoofer output level cannot be adjusted when using headphones.
15
EN08-17.RX-6020V/6022V[J]_f
15
3/4/02, 4:25 PM
Tuner Operations
Front Panel
Remote Control
FM/AM
PRESET
5/∞
(up/down) FM MODE
FM/AM
TUNING
5/∞
(up/down)
A/V CONTROL
RECEIVER
STANDBY/ON
CENTER
AUDIO
TEST
Display
1
REAR L
EFFECT
10 keys
4
TV
6
5
REAR R
MENU
7/P
VCR
9
8
SUBWOOFER
ENTER
10
RX-6020V AUDIO/VIDEO CONTROL RECEIVER
3
2
DVD
10
0
100
RETURN
SLEEP
SOUND
FM/AM TUNING
FM/AM PRESET
FM MODE
REW
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
STANDBY
MEMORY
TUNED STEREO
SPK
L
C
R
S
FF
AUTO MUTING SLEEP
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
VOLUME
MASTER VOLUME
S.WFR LFE
LS
REC PAUSE
RS
CD–DISC
CH-
STANDBY/ON
SURROUND ON/OFF
INPUT ANALOG
INPUT DIGITAL
FM/AM
FM MODE
ADJUST SETTING
DVD MULTI
DVD
VCR
TV SOUND
INPUT ATT
SURROUND MODE
CONTROL
DOWN
UP
SPEAKERS ON/OFF
CD
TAPE/CDR
FM
AM
TAPE/CDR
CD
FM/AM
TV SOUND
DVD
DVD MULTI
VCR
ANALOG
/DIGITAL
FM MODE
ON/OFF
DIMMER TV/VIDEO SURROUND
MUTING
MODE
SOURCE NAME
PHONES
VCR CH
TV CH
TV VOLUME
VOLUME
REMOTE CONTROL RM - SRX6020J
FM/AM
MEMORY
Tuning in Stations
1
Using Preset Tuning
Press FM or AM (FM/AM) to select the band.
The last received station of the selected band is tuned in.
FM
To store the preset stations
AM
FM/AM
On the front panel
ANALOG
TUNED STEREO
SPK
L
C
From the remote control
AUTO MUTING
R
S
RS
CH-
Press FM/AM TUNING 5/∞
(up/down) repeatedly until you find
the frequency you want.
• Pressing FM/AM TUNING 5 (up)
increases the frequency.
• Pressing FM/AM TUNING ∞ (down)
decreases the frequency.
Tune in the station you want to preset
(see “Tuning in Stations” on the left).
• If you want to store the FM reception mode for each preset
station, select the FM reception mode. See “Selecting the FM
Reception Mode” on page 17.
Ex.: When the FM band is selected.
2
Remote
NOT
ANALOG
TUNED STEREO
SPK
L
C
LS
FM/AM TUNING
• When you press and hold FM/AM TUNING 5/∞ (up/down) for few
seconds in step 2, the frequency keeps changing until a station is
tuned in.
• When a station of sufficient signal strength is tuned in, the TUNED
indicator lights up on the display.
• When an FM stereo program is received, the STEREO indicator
also lights up.
VOLUME
RS
S
CH-
2
MEMORY
Press MEMORY.
The “CH-” indicator lights up and the channel
number position starts flashing on the display for
about 5 seconds.
ANALOG
TUNED STEREO AUTO MUTING
SPK
L
C
R
VOLUME
S.WFR LFE
LS
RS
S
CH-
3
Press FM/AM PRESET 5/∞ (up/
down) to select a channel number
while the channel number position
is flashing.
ANALOG
TUNED STEREO
SPK
L
C
R
S.WFR LFE
LS
S
RS
CH-
16
16
AUTO MUTING
R
S.WFR LFE
Notes:
EN08-17.RX-6020V/6022V[J]_f
Remote
NOT
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 2 again.
1
VOLUME
S.WFR LFE
LS
Once a station is assigned to a channel number, the station can be
quickly tuned. You can preset up to 30 FM and 15 AM stations.
3/4/02, 4:25 PM
FM/AM PRESET
AUTO MUTING
VOLUME
Press MEMORY again while the
selected channel number is flashing
on the display.
Selecting the FM Reception Mode
MEMORY
When an FM stereo broadcast is hard to receive or noisy, you can
change the FM reception mode while receiving an FM broadcast.
• You can store the FM reception mode for each preset station (see
page 16).
The selected channel number stops flashing.
The station is assigned to the selected channel number.
ANALOG
TUNED STEREO
SPK
L
C
AUTO MUTING
R
VOLUME
1
S.WFR LFE
S
LS
RS
CH-
5
While listening to an FM station, press
FM MODE.
• Each time you press the button, the FM reception mode
alternates between “AUTO” and “MONO.”
Repeat steps 1 to 4 for storing more stations.
To erase a stored preset station
Storing a new station on a used number erases the previously stored
one.
FM MODE
FM MODE
On the front panel
To tune in a preset station
On the front panel:
ANALOG
C
AUTO MUTING
R
S.WFR LFE
LS
1
TUNED STEREO
SPK
L
From the remote control
S
RS
CH-
Press FM or AM to select the
band.
FM
AM
The last received station of the
selected band is tuned in.
ANALOG
TUNED
SPK
L
C
R
S.WFR LFE
LS
ANALOG
TUNED STEREO
SPK
L
C
RS
CH-
AUTO MUTING
R
S
VOLUME
S.WFR LFE
LS
S
RS
CH-
2
Press FM/AM PRESET 5/∞
(up/down) repeatedly until you find
the channel you want.
• Pressing FM/AM PRESET 5 (up)
increases the channel numbers.
• Pressing FM/AM PRESET ∞ (down)
decreases the channel numbers.
From the remote control:
1
AUTO
: Normally select this.
When a program is broadcasted in stereo, you will
hear stereo sound; when in monaural, you will
hear monaural sounds. This mode is also useful to
suppress static noise between stations. The AUTO
MUTING indicator lights up on the display.
(Initial Setting)
MONO
: Select this to improve the reception (but stereo
effect will be lost).
In this mode, you will hear noise while tuning into
the stations. The AUTO MUTING indicator goes
off from the display. (The STEREO indicator also
goes off.)
FM/AM PRESET
Press FM/AM to select the band (FM or
AM).
FM/AM
The last received station of the selected band is tuned
in and 10 keys now work for tuner operation.
• Each time you press the button, the band
alternates between FM and AM.
2
Press 10 keys to select a preset
channel number.
•
•
•
•
For channel number 5, press 5.
For channel number 15, press +10 then 5.
For channel number 20, press +10 then 10.
For channel number 30, press +10, +10,
then 10.
TEST
1
CENTER
2
EFFECT
4
5
7/P
10
RETURN
6
REAR R
MENU
ENTER
3
REAR L
8
9
SUBWOOFER
0
10
100
Note:
When you use 10 keys on the remote control, be sure that they are
activated for the tuner, not for the CD player and others. (See page
28.)
17
EN08-17.RX-6020V/6022V[J]_f
17
3/4/02, 4:25 PM
Tuner Operations
4
Creating Realistic Sound Fields
You can use the following Surround modes to reproduce a realistic
sound field:
■ Dolby Surround
• Dolby Pro Logic II
• Dolby Digital
■ DTS Digital Surround
■ DAP modes
■ All Channel Stereo
■ Dolby Surround
Dolby Pro Logic II*
Dolby Digital*
Used to reproduce multichannel sound tracks of the software
).
encoded with Dolby Digital (
• To enjoy the software encoded with Dolby Digital, connect the
source component using the digital terminal on the rear of this
receiver. (See page 7.)
D I G I T A L
Dolby Digital 5.1 ch encoding method (so-called discrete
multichannel digital audio format) records and digitally compresses
the left front channel, right front channel, center channel, left rear
channel, right rear channel, and LFE channel signals.
Since each channel is completely independent from the other
channel signals to avoid interference, you can obtain much better
sound quality with much stereo and surround effects.
Dolby Pro Logic II has a newly developed multichannel playback
format to decode all 2 channel sources—regular stereo source and
Dolby Surround encoded source—into 5.1 channel.
Matrix-based encoding/decoding method for Dolby Pro Logic II
makes no limitation for the cutoff frequency of the rear treble and
enables stereo rear sound compared to conventional Dolby Pro
Logic.
Dolby Digital software can be roughly grouped into two categories
—multichannel (up to “5.1” ch) and 2 channel software. To enjoy
surround sounds while playing Dolby Digital 2 ch software, you can
use Dolby Pro Logic II.
Dolby Pro Logic II enables to reproduce spacious sound from
original sound without adding any new sounds and tonal colorations.
Dolby Pro Logic II has two modes—Movie mode and Music mode:
■ DTS Digital Surround**
Pro Logic II Movie (PL II MOVIE)—suitable for reproduction of
DOLBY SURROUND .
Dolby Surround encoded sources bearing the mark
You can enjoy soundfield very close to the one created with discrete
5.1 channel sounds.
Pro Logic II Music (PL II MUSIC)—suitable for reproduction of
any 2 channel stereo music sources. You can enjoy wide and deep
sound by using this mode. For this mode, Panorama control can be
selected, which gives “wraparound” sound effect with side-wall
image.
• When Dolby Pro Logic II is activated,
indicator lights up on the display.
PRO LOGIC II
Note:
Used to reproduce multichannel sound tracks of the software
encoded with DTS Digital Surround (
).
• To enjoy the software encoded with DTS Digital Surround,
connect the source component using the digital terminal on the
rear of this receiver. (See page 7.)
DTS Digital Surround is another discrete multichannel digital
audio format available on CD, LD, and DVD software.
Compared to Dolby Digital, audio compression ratio is relatively
low. This fact allows DTS Digital Surround format to add breadth
and depth to the reproduced sounds. As a result, DTS Digital
Surround features natural, solid and clear sound.
Typical Multichannel (5.1 ch) reproduction
Center
speaker
Left front
speaker
Subwoofer
Right front
speaker
RX-6020V AUDIO/VIDEO CONTROL RECEIVER
FM/AM TUNING
FM/AM PRESET
FM MODE
STANDBY
MASTER VOLUME
MEMORY
STANDBY/ON
D I G I T A L
SURROUND
SURROUND ON/OFF
INPUT ANALOG
SURROUND MODE
SPEAKERS ON/OFF
INPUT DIGITAL
ADJUST SETTING
DVD MULTI
DVD
VCR
TV SOUND
TAPE/CDR
FM
AM
INPUT ATT
CONTROL
DOWN
UP
CD
SOURCE NAME
PHONES
Left rear
speaker
* Manufactured under license from Dolby Laboratories. “Dolby,” “Pro
Logic,” and the double-D symbol are trademarks of Dolby
Laboratories. Confidential Unpublished Works. ©1992–1997 Dolby
Laboratories, Inc. All rights reserved.
** Manufactured underlicense from Digital Theater Systems, Inc. US
PAT. No. 5,451,942 and other world-wide patents issued and
pending. “DTS” and “DTS Digital Surround” are trademarks of
Digital Theater Systems, Inc. Copyright 1996 Digital Theater
Systems, Inc. All rights reserved.
18
EN18-23.RX-6020V/6022V[J]_f
18
Right rear
speaker
3/4/02, 4:25 PM
■ All Channel Stereo
DAP modes have been designed to create important acoustic
surround elements.
This mode can reproduce a larger stereo sound field using all the
connected (and activated) speakers.
The sound heard in a live club, dance club, hall or pavilion consists
of direct sound and indirect sound—early reflections and reflections
from behind. Direct sounds reach the listener directly without any
reflection. On the other hand, indirect sounds are delayed by the
distances of the ceiling and walls (see the diagram below).
These indirect sounds are important elements of the acoustic
surround effects. The DAP mode can reproduce a realistic sound
field by adding these indirect sounds.
All Channel Stereo can be used when the front and rear
speakers are connected to this receiver without respect to the
center speaker connection.
If the center speaker is connected and activated, the same phase of
the front left and right signals are output through the center speaker.
DAP modes can be used when the front and rear speakers are
connected to this receiver (without respect to the center speaker
connection: no sound comes out of the center speaker even if it is
connected).
All Channel Stereo can be used while reproducing 2 channel stereo
software, either analog or digital except Dolby Digital and DTS
Digital Surround.
• When All Channel Stereo is selected, the DSP indicator lights up
on the display.
All Channel Stereo reproduction
The following DAP modes are provided with this receiver:
LIVE CLUB
: Gives the feeling of a live music club with a low
ceiling.
DANCE CLUB : Gives a throbbing bass beat.
HALL
: Gives clear vocal and the feeling of a concert
hall.
PAVILION
: Gives the spacious feeling of a pavilion with a
high ceiling.
These DAP modes can be used to add the acoustic surround effects
while reproducing 2 channel stereo software—either analog or
digital except Dolby Digital and DTS Digital Surround—and can
give you a real “being there” feeling.
• When one of the DAP modes is selected, the DSP indicator lights
up on the display.
Sound reproduced from All Channel Stereo
DVD MULTI Playback Mode
Creating sound field
This receiver provides the DVD MULTI Playback Mode for
reproducing the analog discrete 5.1 channel output mode of the
DVD player or other equipment.
You can adjust speaker output levels while playing back a video
software such as a DVD using the analog discrete 5.1 channel
output mode.
• For connecting analog discrete output jacks, see page 7.
• For details on the DVD MULTI Playback Mode, see page 24.
Reflections from behind
Early reflections
Note:
Direct sounds
When you select “DVD MULTI” as the source to play, Surround mode
is canceled, and the SURROUND ON/OFF and SURROUND MODE
buttons do not work.
䡬: Possible / ⳯: Impossible
Available Surround modes for each input signal
Mode SURROUND
Signals
OFF (stereo)
DOLBY
DIGITAL
DTS
SURROUND
PLII
MOVIE
PLII
MUSIC
LIVE
CLUB
DANCE
CLUB
HALL
PAVILION
ALL CH
STEREO
Dolby Digital
(Multichannel)
䡬
䡬
⳯
⳯
⳯
⳯
⳯
⳯
⳯
⳯
Dolby Digital
(2 channel)
䡬
⳯
⳯
䡬
䡬
⳯
⳯
⳯
⳯
⳯
DTS Digital
Surround
(Multichannel)
䡬
⳯
䡬
⳯
⳯
⳯
⳯
⳯
⳯
⳯
DTS Digital
Surround
(2 channel)
䡬
⳯
⳯
䡬
䡬
⳯
⳯
⳯
⳯
⳯
Linear PCM
䡬
⳯
⳯
䡬
䡬
䡬
䡬
䡬
䡬
䡬
Analog
䡬
⳯
⳯
䡬
䡬
䡬
䡬
䡬
䡬
䡬
19
EN18-23.RX-6020V/6022V[J]_f
19
3/4/02, 4:25 PM
Creating Realistic Sound Fields
■ DAP (Digital Acoustic Processor) modes
Creating Realistic Sound Fields
About Relations between Speaker Layout and Surround Modes
Available Surround modes will vary depending on how many speakers are used with this receiver.
Make sure that you have set the speaker information correctly (see pages 12 to 14).
• If only front speakers are connected, you cannot use any Surround modes.
• If rear speakers are not connected, you cannot use the DAP modes and All Channel Stereo.
Speaker Layout
Available Surround modes
When the center and rear speakers
are connected (5 channels):
Turning on or off Surround modes
Each time you press SURROUND ON/OFF, Surround modes turn on or off.
Front
speaker
TV
Front
speaker
Center speaker
TUNED STEREO
SPK
SURROUND ON/OFF
L
DIGITAL AUTO
LINEAR PCM
AUTO MUTING
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
R
S.WFR
ON/OFF
SURROUND
(Remote)
Last selected
Surround mode
(Front panel)
SURROUND OFF
Ex.: “PL II MUSIC” has been selected.
Rear
speaker
Rear
speaker
Selecting Surround modes
Each time you press SURROUND MODE, Surround modes change as follows:
TUNED STEREO
SPK
SURROUND
SURROUND MODE
DIGITAL AUTO
LINEAR PCM
L
AUTO MUTING
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
R
S.WFR
MODE
When the rear speakers are connected
(4 channels):
(Remote)
Front
speaker
TV
(Front panel)
PL II MOVIE
LIVE CLUB
HALL
ALL CH STEREO
Front
speaker
PL II MUSIC
DANCE CLUB
PAVILION
(Back to the beginning)
Notes:
Rear
speaker
Rear
speaker
When the center speaker is connected
(3 channels):
When the digital multichannel software such as Dolby Digital or DTS Digital
Surround is played back, the appropriate multichannel Surround mode is
automatically activated (“DOLBY DIGITAL” or “DTS SURROUND”) by pressing
SURROUND ON/OFF (with the digital input mode selected).
• For Dolby Digital 2 ch software, you need to select “PLII MUSIC” or “PLII MOVIE”
by pressing SURROUND MODE.
• For more details, see the table on page 19.
Turning on or off Surround modes
Each time you press SURROUND ON/OFF, Surround modes turn on or off.
TUNED STEREO
SPK
Front
speaker
TV
Center speaker
SURROUND ON/OFF
Front
speaker
DIGITAL AUTO
LINEAR PCM
L
R
AUTO MUTING
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
S.WFR
ON/OFF
SURROUND
(Remote)
(Front panel)
PL II MOVIE
or
PL II MUSIC
SURROUND OFF
Ex.: “PL II MUSIC” has been selected.
Selecting Surround modes
Each time you press SURROUND MODE, Surround modes change as follows:
TUNED STEREO
SPK
SURROUND
SURROUND MODE
DIGITAL AUTO
LINEAR PCM
L
R
AUTO MUTING
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
S.WFR
MODE
(Remote)
(Front panel)
PL II MOVIE
PL II MUSIC
Notes:
When the digital multichannel software such as Dolby Digital or DTS Digital
Surround is played back, the appropriate multichannel Surround mode is
automatically activated (“DOLBY DIGITAL” or “DTS SURROUND”) by pressing
SURROUND ON/OFF (with the digital input mode selected).
• For Dolby Digital 2 ch software, you need to select “PLII MUSIC” or “PLII MOVIE”
by pressing SURROUND MODE.
• For more details, see the table on page 19.
20
EN18-23.RX-6020V/6022V[J]_f
20
3/4/02, 4:25 PM
Creating Realistic Sound Fields
Before you start, remember...
• Make sure that you have set the speaker information correctly (see pages 12 to 14).
• You cannot adjust the center speaker output level when you have set “CNTR SP” to “NONE.”
• You cannot adjust the rear speaker output levels when you have set “REAR SP” to “NONE.”
• Remember not to change the speaker setting while using any Surround mode; otherwise, it may be canceled when you deactivate the
speakers required for Surround mode.
Front Panel
Display
RX-6020V AUDIO/VIDEO CONTROL RECEIVER
FM/AM TUNING
FM/AM PRESET
FM MODE
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
STANDBY
MEMORY
TUNED STEREO
SPK
L
C
R
AUTO MUTING SLEEP
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
VOLUME
MASTER VOLUME
S.WFR LFE
LS
S
RS
CH-
STANDBY/ON
SURROUND ON/OFF
INPUT ANALOG
INPUT DIGITAL
ADJUST SETTING
DVD MULTI
DVD
VCR
TV SOUND
TAPE/CDR
FM
AM
INPUT ATT
SURROUND MODE
CONTROL
DOWN
UP
SPEAKERS ON/OFF
CD
SOURCE NAME
PHONES
ADJUST CONTROL
UP 5/DOWN ∞
SURROUND SURROUND
MODE
ON/OFF
Using Dolby Pro Logic II, Dolby Digital and
DTS Digital Surround
Remote Control
CENTER +/–
A/V CONTROL
RECEIVER
STANDBY/ON
CENTER
AUDIO
TEST
TEST
1
REAR L
EFFECT
EFFECT
4
REAR•L +/–
REAR R
7/P
8
VCR
9
SUBWOOFER
ENTER
10
0
DVD
REAR•R +/–
10
100
RETURN
SOUND
TV
6
5
MENU
From the remote control:
3
2
1
FF
REC PAUSE
CD–DISC
TAPE/CDR
CD
DVD
DVD MULTI
FM/AM
TV SOUND
VCR
ANALOG
/DIGITAL
FM MODE
ON/OFF
DIMMER TV/VIDEO SURROUND
MUTING
MODE
VCR CH
It will be convenient for you to use the remote control for
adjustments, since you can make adjustments from your listening
point by using the test signal.
• For selecting Panorama control for Pro Logic II Music, use the
buttons on the front panel.
SLEEP
SOUND
REW
Once you have adjusted the Surround modes, the adjustment is
memorized for each source.
• When playing back digital multichannel software (Dolby Digital
5.1 ch or DTS Digital Surround), the SURROUND MODE button
does not work.
TV CH
When playing back software encoded with Dolby Digital and
DTS Digital Surround, select the digital input mode (see page
11).
SURROUND
ON/OFF
SURROUND
MODE
TV VOLUME
VOLUME
REMOTE CONTROL RM - SRX6020J
Set the analog or digital input mode for the source
you like to listen and start playing.
2
Press SURROUND ON/OFF to
activate Surround mode.
ON/OFF
SURROUND
Each time you press the button, Surround mode
turns on and off alternately.
• If you are playing back software encoded with Dolby Digital
multichannel, “DOLBY DIGITAL” is selected.
• If you are playing back software encoded with DTS Digital
Surround, “DTS SURROUND” is selected.
SURROUND
• If you are playing back any software other
MODE
than above, you can select “PL II MUSIC” or
“PL II MOVIE” according to the source by
pressing SURROUND MODE. ( PRO LOGIC II
indicator lights up on the display.)
If you like to adjust sound, go to step 3.
TO BE CONTINUED ON THE NEXT PAGE
EN18-23.RX-6020V/6022V[J]_f
21
3/4/02, 4:25 PM
21
Creating Realistic Sound Fields
3
Press SOUND.
SOUND
10 keys are activated for sound adjustments.
4
Press TEST to check if you can hear the
sounds through all the speakers at the
equal level.
3
TEST
1
“TEST TONE L” starts flashing on the
display, and a test tone comes out of the
speakers in the following order:
TEST TONE L
TEST TONE C
TEST TONE R
(Left front speaker)
(Center speaker)
(Right front speaker)
TEST TONE LS
TEST TONE RS
(Left rear speaker)
(Right rear speaker)
REAR L : To adjust the left rear speaker output level
(–10 to +10).
REAR R : To adjust the right rear speaker output level
(–10 to +10).
2) Press CONTROL UP 5/
DOWN ∞ to adjust the selected
speaker output levels.
Adjust the speaker output levels
(–10 to +10).
3) Repeat steps 1) and 2) to adjust the other
speaker levels.
CENTER
Press TEST again to stop the test
tone.
3
2
REAR L
5
6
9
8
TEST
1
You can also use the buttons on the front panel to adjust the
Surround modes. However, no test tone is available when using the
buttons on the front panel. So, make adjustments while listening to
the sound of the source played back.
Set the analog or digital input mode for the
source you like to listen and start playing.
When playing back software encoded with Dolby Digital and
DTS Digital Surround, select the digital input mode (see page
11).
2
Press SURROUND ON/OFF
repeatedly to activate Surround
mode.
SURROUND ON/OFF
Each time you press the button, Surround mode turns on and off
alternately.
• If you are playing back software encoded with Dolby Digital
multichannel, “DOLBY DIGITAL” is selected.
• If you are playing back software encoded with DTS Digital
Surround, “DTS SURROUND” is selected.
SURROUND MODE
• If you are playing back any software other
than above, you can select “PL II MUSIC”
or “PL II MOVIE” according to the source
by pressing SURROUND MODE.
( PRO LOGIC II indicator lights up on the display.)
Turn on Panorama control on or off.
1) Press ADJUST repeatedly until
“PANORAMA” (with the current
setting)* appears on the display.
2) Press CONTROL UP 5/DOWN ∞
to select if you turn on or off
Panorama control.
ADJUST
CONTROL
DOWN
UP
• Each time you press the button, “ON” and
“OFF” change alternately.
ON
: Select this when you like to enjoy
“wraparound” sound effect with side-wall
image.
OFF
: Select this when you like to enjoy originally
recorded sounds.
To cancel Surround mode
Press SURROUND ON/OFF again so that “SURROUND OFF”
appears on the display.
• If Surround mode is canceled while playing back multichannel
digital software, all channel signals are mixed and output through
the front speakers (and subwoofer if you have connected a
subwoofer and set the subwoofer setting correctly—“YES”).
22
22
Remote
NOT
* “OFF” is the initial setting. If you have
already changed the setting, “ON” will be shown.
If you like to adjust sound, go to step 3.
EN18-23.RX-6020V/6022V[J]_f
CONTROL
DOWN
UP
When you select “PL II MUSIC,” you can go to the
following adjustment.
4
REAR R
On the front panel:
1
* “0” is the initial setting. If you have already changed the
setting, another number (level) will be shown.
• You can adjust the speaker output levels without outputting the
test tone.
• No test tone comes out of the center speaker when “CNTR SP”
is set to “NONE.”
• No test tone comes out of the rear speakers when “REAR SP”
is set to “NONE.”
Adjust the center speakers and rear speakers levels
by comparing with the sound from the front
speakers.
• To adjust the center speaker level, press
CENTER +/–.
• To adjust the left rear speaker level, press
REAR•L +/–.
• To adjust the right rear speaker level, press
REAR•R +/–.
6
ADJUST
CENTER :To adjust the center speaker output level
(–10 to +10).
Notes:
5
Adjust the speaker output levels.
1) Press ADJUST repeatedly until one
of the following indications (with the
current setting)* appears on the
display.
3/4/02, 4:25 PM
Once you have adjusted the DAP modes and All Channel Stereo, the
adjustment is memorized for each source.
• You cannot use the DAP modes and All Channel Stereo if no rear
speakers are connected and activated.
• You cannot adjust the effect level for All Channel Stereo.
When Surround mode turns on, the last selected Surround mode
will be activated.
• Each time you press the button, Surround mode turns on and off
alternately.
3
From the remote control:
It will be convenient for you to use the remote control for
adjustments, since you can make adjustments from your listening
point.
The DSP indicator also lights up on the display.
If you like to adjust sound, go to step 4.
1
Start playing 2 channel software—either analog
or Linear PCM—and select the source.
2
Press SURROUND ON/OFF to activate
Surround mode.
4
ON/OFF
SURROUND
When Surround mode turns on, the last selected Surround mode
will be activated.
• Each time you press the button, Surround mode turns on and
off alternately.
3
Press SURROUND MODE repeatedly
until one of the DAP modes—“LIVE
CLUB,” “DANCE CLUB,” “HALL,”
“PAVILION”—or “ALL CH STEREO”
appears on the display.
SURROUND MODE
Press SURROUND MODE
repeatedly until one of the DAP
modes—“LIVE CLUB,” “DANCE
CLUB,” “HALL,” “PAVILION,”—
or “ALL CH STEREO” appears on the display.
Adjust the speaker output levels.
1) Press ADJUST repeatedly until one
of the following indications (with the
current setting)* appears on the
display.
REAR L : To adjust the left rear speaker output level
(–10 to +10).
REAR R : To adjust the right rear speaker output level
(–10 to +10).
SURROUND
MODE
CENTER : For “ALL CH STEREO” only—to adjust the
center speaker output level
(–10 to +10).
* “0” is the initial setting. If you have already changed the
setting, another number (level) will be shown.
The DSP indicator also lights up on the display.
If you like to adjust sound, go to step 4.
4
Press SOUND.
2) Press CONTROL UP 5/DOWN ∞
to adjust the selected speaker
output levels.
SOUND
10 keys are activated for sound adjustments.
5
5
6
REAR R
9
8
For “ALL CH STEREO” only:
• To adjust the center speaker level, press
CENTER +/–.
CENTER
3
2
For DAP modes only:
Press EFFECT to select the effect level
(1 to 5) you want.
• Each time you press the button, the effect
level changes as follows:
EFFECT 2
EFFECT 3
EFFECT 1
EFFECT 5
5
Only for DAP modes:
Adjust the DSP effect level.
1) Press ADJUST repeatedly until
“EFFECT” (with the current
setting)* appears on the display.
ADJUST
* “EFFECT 3” is the initial setting. If you have already
changed the setting, another setting will be shown.
EFFECT
4
CONTROL
DOWN
UP
3) Repeat steps 1) and 2) to adjust the
other speaker levels.
REAR L
Adjust the speakers output levels
(–10 to +10).
• To adjust the left rear speaker level, press
REAR•L +/–.
• To adjust the right rear speaker level, press
REAR•R +/–.
6
ADJUST
2) Press CONTROL UP 5/DOWN ∞
to select the effect level (1 to 5) you
want.
CONTROL
DOWN
UP
• Each time you press the button, the effect
level changes as follows:
EFFECT 4
EFFECT 1
As the number increases, the selected mode becomes stronger
(normally set it to “EFFECT 3”).
EFFECT 2
EFFECT 3
EFFECT 4
EFFECT 5
As the number increases, the selected mode becomes
stronger (normally set it to “EFFECT 3”).
On the front panel:
Note:
1
Start playing 2 channel software—either analog
or Linear PCM—and select the source.
2
Press SURROUND ON/OFF to
activate Surround mode.
SURROUND ON/OFF
You cannot select any DAP mode and All Channel Stereo for Dolby
Digital and DTS Digital Surround.
To cancel DAP modes and All Channel Stereo
Press SURROUND ON/OFF so that “SURROUND OFF” appears on
the display. The DSP indicator goes off.
23
EN18-23.RX-6020V/6022V[J]_f
23
3/4/02, 4:26 PM
Creating Realistic Sound Fields
Using DAP Modes and All Channel Stereo
Using DVD MULTI Playback Mode
This receiver provides DVD MULTI Playback Mode for
reproducing the analog discrete output mode of the DVD player.
Before playing back a DVD, refer also to the manual supplied with
your DVD player.
Activating DVD MULTI Playback Mode
You can adjust DVD MULTI Playback Mode while playing back a
DVD with analog discrete output mode on a DVD player.
Once you have made adjustments, the receiver memorizes the
adjustments until you change them.
You also need to set the DVD player to the analog discrete output
mode.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 3 again.
From the remote control:
1 Press DVD MULTI.
DVD MULTI
Note:
When you select “DVD MULTI” as the source to play, Surround
mode is canceled, and the SURROUND ON/OFF and
SURROUND MODE buttons do not work.
2 Select the analog discrete output mode on the
DVD player, and start playing a DVD.
• Refer to the manual supplied with the DVD player.
If you need to make any adjustment, go to the
following steps.
3 Press SOUND.
SOUND
10 keys are activated for adjusting the sound.
On the front panel:
1 Press DVD MULTI.
DVD MULTI
Note:
When you select “DVD MULTI” as the source to play, Surround
mode is canceled, and the SURROUND ON/OFF and
SURROUND MODE buttons do not work.
2 Select the analog discrete output mode on the
DVD player, and start playing a DVD.
• Refer also to the manual supplied with the DVD player.
4 Adjust the speaker output levels.
• To adjust the center speaker level, press
CENTER +/– (–10 to +10).
2
• To adjust the left rear speaker level, press
REAR•L +/– (–10 to +10).
5
• To adjust the right rear speaker level, press
REAR•R +/– (–10 to +10).
If you need to make any adjustment, go to the
following steps.
3 Adjust the speaker output levels.
1) Press ADJUST repeatedly until one
of the following indications appears
on the display.
ADJUST
CENTER
: To adjust the center speaker level.
REAR L
: To adjust the left rear speaker level.
REAR R
: To adjust the right rear speaker level.
2) Press CONTROL UP 5/DOWN ∞
to adjust the selected speaker
output levels (–10 to +10).
CONTROL
DOWN
UP
3) Repeat steps 1) and 2) to adjust the other
speaker output levels.
24
EN24-31.RX-6020V/6022V[J]_f
24
3/4/02, 4:26 PM
CENTER
3
REAR L
6
REAR R
8
9
COMPU LINK Remote Control System
Automatic Power On/Off (Standby): Only possible with the
COMPU LINK-3 and COMPU LINK-4
Both the CD player and cassette deck (or CD recorder) turn on and
off (standby) along with the receiver.
When you turn on the receiver, the CD player or cassette deck (or
CD recorder) will turn on automatically, depending on which
component has been previously selected.
When you turn off the receiver, both the CD player and cassette
deck (or CD recorder) will turn off (standby).
Synchronized Recording
Cassette deck
or
CD recorder
Synchronized recording means the cassette deck starts recording as
soon as a CD begins playing.
To use synchronized recording, follow these steps:
COMPU LINK-4
(SYNCHRO)
1 Put a tape in the cassette deck and a disc in the
CD player.
CD player
Notes:
• There are four versions of COMPU LINK remote control system.
This receiver is equipped with the fourth version—COMPU LINK-4.
This version is added systematic operations with the CD recorder
to the previous version—COMPU LINK-3.
• If your audio component has two COMPU LINK jacks, you can use
either one. If it has only one COMPU LINK jack, connect it so that it
is the last item in the series of components.
• To operate the cassette deck or CD recorder using the COMPU
LINK remote control system, set the source name correctly.
(See page 8.)
• Refer also to the manuals supplied with your audio components.
This remote control system allows you to use four functions listed
below.
Remote Control through the Remote Sensor on the Receiver
2 Press the record (¶) button and the pause (8)
button on the cassette deck at the same time.
This puts the cassette deck into recording pause.
If you do not press the record (¶) button and pause (8) button at
the same time, the synchronized recording feature will not
operate.
3 Press the play (3) button on the CD player.
The source changes on the receiver, and as soon as play starts,
the cassette deck starts recording. When the play ends, the
cassette deck enters recording pause, and stops about 4 seconds
later.
Notes:
• During synchronized recording, the selected source cannot be
changed.
• If the power of any component is shut off during synchronized
recording, the COMPU LINK remote control system may not
operate properly. In this case, you must start again from the
beginning.
You can control the connected audio components through the
remote sensor on the receiver using this remote control. Aim the
remote control directly at the remote sensor on the receiver. For
details, see pages 28 and 29.
Automatic Source Selection
3) button on a connected component or
When you press the play (3
on its own remote control, the receiver automatically turns on and
changes the source to the component. On the other hand, if you
select a new source on the receiver or on the remote control, the
selected component begins playing immediately.
In both cases, the previously selected source continues playing
without sound for a few seconds.
25
EN24-31.RX-6020V/6022V[J]_f
25
3/4/02, 4:26 PM
Using DVD MULTI Playback Mode / COMPU LINK Remote Control System
The COMPU LINK remote control system allows you to operate
JVC’s audio components through the remote sensor on the receiver.
To use this remote control system, you need to connect JVC’s audio
components through the COMPU LINK–4 (SYNCHRO) jacks (see
below) in addition to the connections using cables with RCA pin
plugs (see page 6).
• Make sure that the AC power cords of these components are
unplugged before making connection. Plug the AC power cords
only after all connections are completed.
AV COMPU LINK Remote Control System
The AV COMPU LINK remote control system allows you to operate JVC’s audio components through the remote sensor on the receiver.
To use this remote control system, you need to connect the video components you want to operate by following the diagram and the
procedure below.
• Make sure that AC power cords of these components are unplugged before connecting. Plug AC power cords only after all connections are
completed.
CONNECTIONS:
VCR
DVD player
TV
VHS
DVD
AV
COMPU LINK
AV
COMPU LINK
AV
COMPU LINK EX
AV
COMPU LINK
AV
COMPU LINK III
Note:
You can only connect to the TV with the AV COMPU LINK EX or AV
COMPU LINK III terminal.
The TV with AV COMPU LINK RECEIVER/AMP terminal will not be
used.
Notes:
•
•
•
•
When connecting only the VCR and DVD player to this receiver, use the cable with monaural mini-plugs.
You can connect only the TV with AV COMPU LINK to the AV COMPU LINK terminal.
Refer also to the manuals supplied with your video components.
Make sure that the remote control code of the VCR connected to the VCR jacks is set to code “A.”
1 Unplug your VCR, DVD player, TV, and this
receiver from the AC outlets.
2 Connect your VCR, DVD player, TV, and this
receiver using cables with the monaural miniplugs (not supplied).
• See “CONNECTIONS” above.
3 Connect VCR, DVD player, TV, and this receiver
using cables with RCA pin plug.
5 When turning on the TV for the first time after
the AV COMPU LINK connection, turn the TV
volume to the minimum with the volume control
on the TV.
6 Turn on the other connected components first,
then turn on this receiver.
• When turning on the VCR, use the remote control supplied
VCR).
with this receiver (press STANDBY/ON
• See pages 6 and 7.
4 Plug AC power cords of the components back into
the AC outlets.
26
EN24-31.RX-6020V/6022V[J]_f
26
3/4/02, 4:26 PM
Remote Control of the TV, DVD player, and VCR Using This
Remote Control
• Aim the remote control directly at the remote sensor on each
component (see page 29 for details).
Automatic Selection of TV’s Input Mode
• When you select “TV SOUND” (or “TV DIGITAL”) as the source
to play on the receiver, the TV automatically changes the input
mode to the TV tuner so that you can watch TV.
• When you select “DVD” (or “DVD DIGITAL”), “DVD MULTI,”
or “VCR” as the source to play on the receiver, the TV
automatically changes the input mode to the appropriate position
(either Video Input 1 or Video Input 2) so that you can view the
playback picture.
One-Touch Video Play
Simply by inserting a video cassette without its safety tab into the
VCR, you can enjoy the video playback without setting other
switches manually. The receiver automatically turns on and changes
the source to “VCR.”
The TV automatically turns on and changes the input mode to the
appropriate position so that you can view the playback picture.
When you insert a video cassette with its safety tab, press the play
3) button on the VCR or on the remote control. You can get the
(3
same result.
One Touch DVD Play
Simply by starting playback on the DVD player, you can enjoy the
DVD playback without setting other switches manually.
• When DVD player is connected through the analog input jacks on
this receiver (and analog input is selected), the receiver
automatically turns on and changes the source to “DVD” or “DVD
MULTI.”
• When the DVD player is connected through the digital input
terminal on this receiver (and digital input is selected), the
receiver automatically turns on and changes the source to “DVD
DIGITAL.”
The TV automatically turns on and changes the input mode to the
position so that you can view the playback picture.
Automatic Power On/Off
The TV, VCR, and DVD player turn on and off along with the
receiver.
When you turn on the receiver;
• If the previously selected source is “VCR,” the TV and VCR will
turn on automatically.
• If the previously selected source is “TV SOUND” (or “TV
DIGITAL”), only the TV will turn on automatically.
• If the previously selected source is “DVD” (or “DVD DIGITAL”)
or “DVD MULTI,” the TV and DVD player will turn on
automatically.
When you turn off the receiver, the TV, VCR and the DVD player
will turn off.
Note:
Even if you turn off the receiver while recording on the VCR, the VCR
will not turn off and continues recording.
27
EN24-31.RX-6020V/6022V[J]_f
27
3/4/02, 4:26 PM
AV COMPU LINK Remote Control System
The AV COMPU LINK remote control system allows you to use
five basic functions listed below.
Operating JVC’s Audio/Video Components
You can use the remote control to operate other JVC’s
components.
Operating Audio Components
CD player
After pressing CD, you can use following buttons for CD operations:
3
: Start playback.
4
: Return to the beginning of the current
(or previous) track.
IMPORTANT:
¢
: Skip to the beginning of the next track.
To operate JVC’s audio components using this remote control:
• You need to connect JVC’s audio components through the COMPU
LINK (SYNCHRO) jacks (see page 25) in addition to the
connections using cables with RCA pin plugs (see page 6).
• Aim the remote control directly at the remote sensor on the receiver.
• If you use the buttons on the front panel, the remote control will not
operate that source. To operate a source with the remote control,
the source must be selected with source selecting buttons on the
remote control.
• To operate the cassette deck or CD recorder by COMPU LINK
remote control system, set the source name correctly. (See page 8.)
• Refer also to the manuals supplied with your audio components.
7
: Stop playback.
8
: Pause playback. To release it, press 3.
1 – 10, +10
: Select a track number directly.
• For track number 5, press 5.
• For track number 15, press +10, then 5.
• For track number 20, press +10, then 10.
CD changer
After pressing CD-DISC, you can use following buttons for CD
changer operations:
Sound Adjustment
3
: Start playback.
You can always use following buttons for sound adjustment:
4
: Return to the beginning of the current
(or previous) track.
SURROUND ON/OFF : Turn on or off Surround modes.
¢
: Skip to the beginning of the next track.
SURROUND MODE
7
: Stop playback.
8
: Pause playback. To release it, press 3.
1 – 6, 7/P
: Select the number of a disc installed in a CD
changer.
: Select Surround modes.
After pressing SOUND, you can use following buttons for sound
adjustment:
SUBWOOFER +/–
: Adjust the subwoofer output level.
CENTER +/–
: Adjust the center speaker output level.
REAR•L +/–
: Adjust the left rear speaker output level.
REAR•R +/–
: Adjust the right rear speaker output level.
EFFECT
: Select the DAP effect level.
TEST
: Turn on or off the test tone output.
Note:
After adjusting sounds, press the corresponding source selecting
button or CD-DISC to operate your target source with 10 keys on the
remote control, otherwise 10 keys cannot be used for operating your
target source.
Tuner
If your CD changer is of 200-disc loading capability (except for
XL-MC100 and XL-MC301),
you can do following operations with number buttons after pressing
CD:
1 Select a disc number.
2 Then select a track number (always enter two digits).
3 Start playback.
Examples:
• Selecting disc number 3, track number 2, and start playback.
Press 3, then, 0, 2, then 3.
• Selecting disc number 10, track number 5, and start playback.
Press 1, 0, then, 0, 5, then 3.
• Selecting disc number 105, track number 12, and start playback.
Press 1, 0, 5, then 1, 2, then 3.
You can always use following buttons:
FM/AM
: Alternate between FM and AM.
FM MODE
: Change the FM reception mode.
After pressing FM/AM, you can use following buttons for Tuner
operations:
1 – 10, +10
: Select a preset channel number directly.
• For channel number 5, press 5.
• For channel number 15, press +10, then 5.
• For channel number 20, press +10, then 10.
CD recorder
Before starting operations described below, make sure that you have
changed the source name correctly. See page 8.
After pressing TAPE/CDR, you can use following buttons for CD
recorder operations:
3
: Start playback.
4
: Return to the beginning of the current
(or previous) track.
¢
: Skip to the beginning of the next track.
7
: Stop playback or recording.
8
: Pause playback. To release it, press 3.
REC PAUSE
: Press this button to enter recording pause.
Press this button and then 3 to start recording.
28
EN24-31.RX-6020V/6022V[J]_f
28
3/4/02, 4:26 PM
DVD player
Before starting operations described below, make sure that you have
changed the source name correctly. See page 8.
You can always perform following operations:
After pressing TAPE/CDR, you can use following buttons for
cassette deck operations:
STANDBY/ON
DVD : Turn on or off a DVD player.
After pressing DVD or DVD MULTI, you can use following buttons
for DVD player operations:
3
: Start playback.
3
: Start playback.
FF
: Fast wind the tape from left to right.
4
REW
: Fast wind the tape from right to left.
: Return to the beginning of the current
(or previous) track.
7
: Stop playback or recording.
¢
: Skip to the beginning of the next track.
8
: Pause playback. To release it, press 3.
7
: Stop playback.
REC PAUSE
: Press this button to enter recording pause.
Press this button and then 3 to start recording.
8
: Pause playback. To release it, press 3.
Operating Video Components
DVD menu operations
After pressing DVD or DVD MULTI, you can
use following buttons for DVD menu
operations:
TEST
1
EFFECT
4
7/P
10
RETURN
To operate JVC’s video components using this remote control:
• Some JVC’s VCRs can accept two types of the control signals—
remote code “A” and “B.” Before using this remote control, make
sure that the remote control code of the VCR connected to the VCR
jacks is set to code “A.”
• Aim the remote control directly at the remote sensor on each
component, not on the receiver.
MENU
: Display or erase the menu screen.
5/∞
∞/3
3/2
2
: Select an item on the menu screen.
ENTER
: Enter a selected item.
3
REAR L
5
6
REAR R
MENU
ENTER
IMPORTANT:
CENTER
2
8
9
SUBWOOFER
0
10
100
TV
VCR
You can always perform following operations:
You can always perform following operations:
STANDBY/ON
STANDBY/ON
VCR CH +/–
VCR :Turn on or off a VCR.
TV : Turn on or off a TV.
TV/VIDEO
: Change the input mode (TV tuner and video
input).
TV VOLUME +/–
: Adjust the volume.
TV CH +/–
: Change the channels.
:Change the TV channels on the VCR.
After pressing VCR (source selecting button), you can use following
buttons for VCR operations:
After pressing TV SOUND, you can use following buttons for TV
operations:
3
: Start playback.
FF
: Fast wind a tape.
REW
: Rewind a tape.
1 – 9, 0, 100+ (+10)
:Select a channel.
7
: Stop playback or recording.
RETURN (10)
:Function as the RETURN button.
8
: Pause playback. To release it, press 3.
REC PAUSE
: Press this button to enter recording pause.
Press this button and then 3 to start recording.
29
EN24-31.RX-6020V/6022V[J]_f
29
3/4/02, 4:26 PM
Operating JVC's Audio / Video Components
Cassette deck
Troubleshooting
Use this chart to help you solving daily operational problems. If there is any problem you cannot solve, contact your JVC service center.
PROBLEM
POSSIBLE CAUSE
The power does not turn on.
The power cord is not plugged in.
Plug the power cord into an AC outlet.
No sound from speakers.
Speaker signal cables are not connected.
Check speaker wiring and reconnect if
necessary.
The SPEAKERS ON/OFF button is not
set correctly.
Press SPEAKERS ON/OFF button correctly.
An incorrect source is selected.
Select the correct source.
Muting is activated.
Press MUTING to cancel the mute.
An incorrect input mode (analog or
digital) is selected.
Select the correct input mode (analog or
digital).
Connections are incorrect.
Check connections.
For analog connections, see page 6.
For digital connections, see page 7.
Speaker signal cables are not connected
properly.
Check speaker wiring and reconnect if
necessary.
The balance is set to one extreme.
Adjust the balance properly (see page 15).
Incoming signal is too weak.
Connect an outdoor FM antenna or contact
your dealer.
The station is too far away.
Select a new station.
An incorrect antenna is used.
Check with your dealer to be sure you have the
correct antenna.
Antennas are not connected properly.
Check connections.
Occasional cracking noise during FM
reception.
Ignition noise from automobiles.
Move the antenna farther from automobile
traffic.
“OVERLOAD” starts flashing on the
display.
Speakers are overloaded because of high
volume.
on the front
1. Press STANDBY/ON
panel to turn off the receiver.
2. Stop the playback source.
3. Turn on the receiver again, and adjust the
volume.
Speakers are overloaded because of short
circuit of speaker terminals.
on the front panel,
Press STANDBY/ON
then check the speaker wiring.
If “OVERLOAD” does not disappear, unplug
the AC power cord, then plug it back again.
If speaker wiring is not short-circuited, contact
your dealer.
“DSP MICON NG” starts flashing on the
display.
The built-in microcomputer is not
functioning correctly.
on the front panel to
Press STANDBY/ON
turn off the receiver. After unplugging the
power cord, consult your dealer.
The STANDBY lamp lights up after
turning on the power, but soon the
receiver turns off (into standby mode).
The receiver is overloaded because of a
high voltage.
on the front panel to
Press STANDBY/ON
turn off the receiver. After unplugging the
power cord, consult your dealer.
Remote control does not work.
There is an obstruction in front of the
remote sensor on the receiver.
Remove the obstruction.
Batteries are weak.
Replace batteries.
An incorrect remote control operation
mode is selected.
Select the correct remote control operation
mode (see pages 28 and 29).
Sound from one speaker only.
Continuous hiss or buzzing during FM
reception.
Remote control does not work for the
source (or other components) you try to
operate.
SOLUTION
30
EN24-31.RX-6020V/6022V[J]_f
30
3/4/02, 4:26 PM
Specifications
Designs & specifications are subject to change without notice.
Output Power
At Stereo operation:
Front channels:
100 W per channel, min. RMS, driven into 8 Ω,
40 Hz to 20 kHz with no more than 0.8% total
harmonic distortion.
At Surround operation:
Audio
Audio Input Sensitivity/Impedance (1 kHz):
Audio Input (DIGITAL IN)* :
Front channels:
100 W per channel, min. RMS, driven into 8 Ω at 1 kHz with no
more than 0.8% total harmonic distortion.
Center channel:
100 W, min. RMS, driven into 8 Ω at 1 kHz, with no more than
0.8% total harmonic distortion.
Rear channels:
100 W per channel, min. RMS, driven into 8 Ω at 1 kHz, with no
more than 0.8% total harmonic distortion.
DVD, VCR, TV SOUND, CD, TAPE/CDR: 220 mV/47 k Ω
Coaxial: DIGITAL 1 (DVD):
Optical: DIGITAL 2 (CD):
0.5 V (p-p)/75 Ω
–21 dBm to –15 dBm (660 nm ±30 nm)
* Corresponds to Linear PCM, Dolby Digital, and DTS Digital Surround
(with sampling frequency — 32 kHz, 44.1 kHz, 48 kHz).
Audio Output Level:
Signal-to-Noise Ratio (’66 IHF/’78 IHF):
Frequency Response (8 Ω):
Tone Control:
TAPE/CDR, VCR:
220 mV
DVD, VCR, TV SOUND, CD, TAPE/CDR: 87 dB/78 dB
DVD, VCR, TV SOUND, CD, TAPE/CDR: 20 Hz to 20 kHz (±1 dB)
Bass (100 Hz):
Treble (10 kHz):
±10 dB
±10 dB
VCR, DVD:
1 V (p-p)/75 Ω
VCR, MONITOR OUT:
1 V (p-p)/75 Ω
Video
Video Input Sensitivity/Impedance:
Composite video:
Video Output Level/Impedance:
Composite video:
Synchronization:
Signal-to-Noise Ratio:
Negative
45 dB
FM tuner (IHF)
Tuning Range:
87.5 MHz to 108.0 MHz
Usable Sensitivity:
Monaural:
12.8 dBf (1.2 µV/75 Ω)
50 dB Quieting Sensitivity:
Monaural:
Stereo:
21.3 dBf (3.2 µV/75 Ω)
41.3 dBf (31.5 µV/75 Ω)
Signal-to-Noise Ratio (IHF-A weighted):
Monaural:
Stereo:
78 dB at 85 dBf
73 dB at 85 dBf
Total Harmonic Distortion:
Monaural:
Stereo:
0.4% at 1 kHz
0.6% at 1 kHz
Stereo Separation at REC OUT:
Alternate Channel Selectivity:
Frequency Response:
35 dB at 1 kHz
45 dB: (±400 kHz)
30 Hz to 15 kHz: (+0.5 dB, –3 dB)
AM tuner
Tuning Range:
Usable Sensitivity:
Signal-to-Noise Ratio:
530 kHz to 1 710 kHz
Loop antenna
400 µV/m
50 dB (100 mV/m)
General
Power Requirements:
AC 120V
Power Consumption:
180 W/230 VA (at operation)
2 W (in standby mode)
Dimensions (W x H x D):
Mass:
, 60 Hz
435 mm x 146.5 mm x 416 mm (17 3/16 in. x 5 13/16 in. x 16 7/16 in.)
8.8 kg (19.5 lbs)
31
EN24-31.RX-6020V/6022V[J]_f
31
3/4/02, 4:26 PM
Trouble Shooting / Specifications
Amplifier
Authorized Service Centers
®
QUALITY
SERVICE
HOW TO LOCATE YOUR JVC SERVICE CENTER
TOLL FREE: 1 (800) 537-5722
http://www.jvc.com
Dear Customer,
In order to receive the most satisfaction from your purchase,please read the instruction booklet before
operating the unit.In the event that repairs are necessary, please call 1 (800)537-5722 for your nearest
authorized servicer or visit our website at www.JVC.com
Remember to retain your Bill of Sale for Warranty Service.
Do not service the television yourself
Caution
To prevent electrical shock,do not open the cabinet.There are no user serviceable
parts inside.Please refer to qualified service personnel for repairs.
Accessories
To purchase accessories for your JVC product,please call toll free:1 (800)882-2345 or
on the web at www.JVC.com
BT-51002-5
(0301)
RX-6020V/6022V[J]_Warranty_f
2
3/4/02, 4:26 PM
LIMITED WARRANTY
AUDIO-2
JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE
ORIGINAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date
of original retail purchase for the period as shown below. ("The Warranty Period")
PARTS
2
LABOR
YRS
2
YRS
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND
IN COMMONWEALTH OF PUERTO RICO.
WHAT WE WILL DO:
If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner.
Such repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized service
centers. Parts used for replacement are warranted only for the remainder of the Warranty Period. All products and parts
thereof may be brought to a JVC authorized service center on a carry-in basis except for Television sets having a screen
size 25 inches and above which are covered on an in-home basis.
WHAT YOU MUST DO FOR WARRANTY SERVICE:
Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized
service center, please call toll free: (800) 537-5722.
If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with
a copy of your bill of sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center, the
name and location of which will be given to you by the toll-free number.
If you have any questions concerning your JVC Product, please contact our Customer Relations Department.
WHAT IS NOT COVERED:
This limited warranty provided by JVC does not cover:
1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty
installation, lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized by
JVC to render such service, or if affixed to any attachment not provided with the products, or if the model number
or serial number has been altered, tampered with, defaced or removed;
2. Initial installation and installation and removal for repair;
3. Operational adjustments covered in the Owner's Manual, normal maintenance, video and audio head cleaning;
4. Damage that occurs in shipment, due to act of God, and cosmetic damage;
5. Signal reception problems and failures due to line power surge;
6. Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90 days from the date of purchase;
7. Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase);
There are no express warranties except as listed above.
THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IS
LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN.
JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY OTHER
DAMAGES, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGE
TO TAPES, RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH
OF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE.
Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an
implied warranty lasts, so these limitations or exclusions may not apply to you. This warranty gives you specific
legal rights and you may also have other rights which vary from state to state.
JVC COMPANY OF AMERICA
DIVISION OF JVC AMERICAS CORP.
1700 Valley Road
Wayne, NJ 07470
REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR DETAILS OF
REFURBISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION
PACKAGED WITH EACH REFURBISHED PRODUCT.
For customer use:
Enter below the Model No. which is located either on the rear, bottom or side of the cabinet. Retain this information
for future reference.
RX-6020V/6022V[J]_Warranty_f
Model No. :
Serial No. :
Purchase data :
Name of dealer :
3
3/4/02, 4:26 PM
VICTOR COMPANY OF JAPAN, LIMITED
V
EN
RX-6020V/6022V[J]_COVER_f
J
2
3/4/02, 4:17 PM
C
0302NHMMDWJEIN