AUDIO/VIDEO CONTROL RECEIVER
RX-7022VSL
A/V CONTROL RECEIVER
CATV/DBS
VCR
DVD
DVD MULTI
CD
FM/AM
TV/DBS
VCR
TAPE/CDR
PHONO
−
BASS
SURROUND
ON/OFF
+
TV
−
AUDIO
TREBLE
+
SURROUND ANALOG/DIGITAL SLEEP
MODE
BASS BOOST EFFECT
1
INPUT
– CENTER +
2
3
MENU
SOUND
TEST
4
RX-7022V
– REAR•L +
5
AUDIO/VIDEO CONTROL RECEIVER
6
ENTER
– REAR•R +
DIMMER
7/P
8
FM/AM TUNING
FM/AM PRESET
FM MODE
9
STANDBY
CATV/DBS
CONTROL
TV/VIDEO
10
0
+10
RETURN
FM MODE
100+
+
+
+
CH
TV VOL
VOLUME
−
−
COMPULINK
Remote
MASTER VOLUME
– SUB WOOFER +
MUTING
MEMORY
STANDBY/ON
−
SURROUND ON/OFF
INPUT
ANALOG/DIGITAL
BASS BOOST
ADJUST SETTING
DVD MULTI
DVD
VCR
TV SOUND/DBS
INPUT ATT
+
TUNING
SOURCE NAME
/REW
SURROUND MODE
FF/
−
CONTROL
DOWN
UP
SPEAKERS ON/OFF
1
REC
PAUSE
2
CD
TAPE/CDR
PHONO
FM/AM
SOURCE NAME
PHONES
CONTROL
RM-SRX7022U REMOTE CONTROL
INSTRUCTIONS
For Customer Use:
Enter below the Model No. and Serial
No. which are located either on the rear,
bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
LVT0852-006A
[A]
RX-7020V[A]_COVER2
1
02.4.9, 3:46 PM
Warnings, Cautions and Others
Caution ––
switch!
Disconnect the mains plug to shut the power off completely. The
switch in any position does not disconnect the mains line. The power
can be remote controlled.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
CAUTION
• Do not block the ventilation openings or holes.
(If the ventilation openings or holes are blocked by a
newspaper or cloth, etc., the heat may not be able to
get out.)
• Do not place any naked flame sources, such as
lighted candles, on the apparatus.
• When discarding batteries, environmental problems
must be considered and local rules or laws governing
the disposal of these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture,
dripping or splashing and that no objects filled with
liquids, such as vases, shall be placed on the
apparatus.
G-1
RX-7022V[A]_Safety
1
02.4.17, 5:14 PM
Caution: Proper Ventilation
To avoid risk of electric shock and fire and to protect from damage.
Locate the apparatus as follows:
Front:
No obstructions open spacing.
Sides:
No obstructions in 10 cm from the sides.
Top:
No obstructions in 10 cm from the top.
Back:
No obstructions in 15 cm from the back.
Bottom:
No obstructions, place on the level surface.
In addition, maintain the best possible air circulation as illustrated.
Spacing 15 cm or more
RX-7022VSL
Wall or obstructions
Front
Stand height 15 cm or more
Floor
G-2
RX-7022V[A]_Safety
2
02.4.17, 5:14 PM
Table of Contents
Parts Identification ...................................... 2
Getting Started ........................................... 3
Before Installation ...................................................................... 3
Checking the Supplied Accessories ........................................... 3
Putting Batteries in the Remote Control .................................... 3
Connecting the FM and AM Antennas ....................................... 4
Connecting the Speakers ............................................................ 5
Connecting Audio/Video Components ....................................... 6
Connecting the Power Cord ....................................................... 9
Basic Operations ....................................... 10
Turning On the Power .............................................................. 10
Selecting the Source to Play ..................................................... 10
Adjusting the Volume ............................................................... 11
Selecting the Front Speakers .................................................... 11
Listening Only with Headphones ............................................. 12
Turning Off the Sounds Temporarily—Muting ........................ 12
Changing the Display Brightness ............................................. 12
Turning Off the Power with the Sleep Timer ........................... 12
Basic Settings ........................................... 14
Setting the Digital Input (DIGITAL IN) Terminals ................. 14
Selecting the Analog or Digital Input Mode ............................ 15
Selecting the Video Input Terminal .......................................... 16
Setting the Speaker Information ............................................... 16
Sound Adjustments .................................... 19
Attenuating the Input Signal .................................................... 19
Adjusting the Front Speakers Output Balance ......................... 19
Adjusting the Tone ................................................................... 20
Adjusting the Subwoofer Output Level .................................... 20
Reinforcing the Bass ................................................................ 20
Tuner Operations ....................................... 21
Tuning in Stations Manually .................................................... 21
Using Preset Tuning ................................................................. 21
Selecting the FM Reception Mode ........................................... 22
Creating Realistic Sound Fields ................... 23
About Relations between Speaker Layouts and
Surround Modes ................................................................. 25
Using Dolby Pro Logic II, Dolby Digital
and DTS Digital Surround ................................................. 26
Using DAP Modes and All Channel Stereo ............................. 28
Using DVD MULTI Playback Mode ................ 30
Activating DVD MULTI Playback Mode ................................ 30
COMPU LINK Remote Control System ......... 31
AV COMPU LINK Remote Control System .... 32
Operating JVC’s Audio/Video
Components .......................................... 34
Operating Audio Components .................................................. 34
Operating Video Components .................................................. 36
Operating Other Manufacturers’ Video
Equipment ............................................ 37
Troubleshooting ......................................... 40
Specifications ............................................ 41
This mark indicates that the remote control CAN
ONLY be used for the operation explained.
Remote
NOT
This mark indicates that the remote control CANNOT
be used for the operation explained. Use buttons on
the front panel.
1
EN01-09.RX-7020V[A]3
1
02.4.17, 5:14 PM
Parts Identification
Front Panel
2
3
FM/AM TUNING
FM/AM PRESET
1
45
7 89
6
p
RX-7022V AUDIO/VIDEO CONTROL RECEIVER
FM MODE
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
STANDBY
MEMORY
SPK 1 2
L
C
BASS BOOST
TUNED STEREO
AUTO MUTING SLEEP
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
R
VOLUME
S.WFR LFE
LS
S
MASTER VOLUME
RS
CH-
STANDBY/ON
SURROUND ON/OFF
INPUT
ANALOG/DIGITAL
BASS BOOST
ADJUST SETTING
DVD MULTI
DVD
VCR
CD
TAPE/CDR
PHONO
TV SOUND/DBS
INPUT ATT
SOURCE NAME
SURROUND MODE
CONTROL
DOWN
UP
SPEAKERS ON/OFF
1
2
FM/AM
SOURCE NAME
PHONES
q
w e r
t
y
u
i
o
See pages in the parentheses for details.
Remote Control
A/V CONTROL RECEIVER
1
a
2
3
4
5
6
7
8
9
p
b
CATV/DBS
VCR
TV
AUDIO
DVD
DVD MULTI
CD
FM/AM
VCR
TAPE/CDR
TV/DBS
−
BASS
SURROUND
ON/OFF
BASS BOOST EFFECT
1
−
+
SLEEP
INPUT
– CENTER +
2
y
u
i
3
MENU
SOUND
TEST
– REAR • L +
4
5
7/P
8
6
ENTER
DIMMER
– REAR • R +
CATV/DBS
CONTROL
TV/VIDEO
r
TUNING
9
o
– SUB WOOFER +
MUTING
q
w
e
t
+
SURROUND ANALOG/DIGITAL
MODE
PHONO
TREBLE
10
0
+10
RETURN
FM MODE
100+
+
+
+
CH
TV VOL
VOLUME
−
−
−
;
a
+
/REW
FF/
−
REC
PAUSE
s
Front Panel
Remote Control
1 STANDBY/ON
button and STANDBY
lamp (10)
2 FM/AM TUNING 5/∞ buttons (21)
3 FM/AM PRESET 5/∞ buttons (21, 22)
4 FM MODE button (22)
5 MEMORY button (21, 22)
6 Display (10)
7 ADJUST button (19, 20, 27 – 29, 30)
8 Remote sensor (3)
9 SETTING button (14, 16 – 18)
p MASTER VOLUME control (11)
q PHONES jack (12)
w SURROUND ON/OFF button (25, 27, 29)
e SURROUND MODE button (25, 27, 29)
r • INPUT ANALOG/DIGITAL button (15)
• INPUT ATT button (19)
t • SPEAKERS ON/OFF 1 button (11, 12)
• SPEAKERS ON/OFF 2 button (11, 12)
y BASS BOOST button (20)
u SOURCE NAME buttons (11)
i Source selecting buttons
(10, 11, 15, 21, 22, 30)
DVD MULTI, DVD, VCR,
TV SOUND/DBS, CD, TAPE/CDR,
PHONO, FM/AM
o CONTROL UP5/DOWN∞ buttons
(14, 16 – 20, 27 – 29, 30)
1 Display window
a: Remote control operation mode indicator
b: Signal transmission indicator
Lights up when transmitting the remote
control signal
2 Power buttons (10, 36 – 39)
, VCR
, TV
,
CATV/DBS
AUDIO
3 Source selecting buttons
(10, 11, 15, 21, 22, 30, 34 – 39) *
DVD, DVD MULTI, CD, FM/AM, TV/DBS,
VCR, TAPE/CDR, PHONO
4 BASS +/– buttons (20)
5 SURROUND ON/OFF button (25, 26, 28)
6 SURROUND MODE button (25, 26, 28)
7 BASS BOOST button (20)
8 SOUND button (20, 27, 28, 30) *
9 DIMMER button (12)
p MUTING button (12)
q CATV/DBS CONTROL button (37) *
w TV/VIDEO button (36, 37)
e CH (channel) +/– buttons (36 – 38)
r TUNING +/– buttons (21)
t REC PAUSE button (35, 36, 38)
y TREBLE +/– buttons (20)
u SLEEP button (12)
i ANALOG/DIGITAL INPUT button (15)
o • 10 keys for selecting preset channels (22)
• 10 keys for adjusting sound (20, 27, 28, 30)
• 10 keys for operating audio/video components
(34 – 39)
; TV VOL (volume) +/– buttons (36, 37)
a VOLUME +/– buttons (11)
s Operating buttons for audio/video
components(35, 36, 38, 39)
d CONTROL button (34 – 36) *
d
CONTROL
RM-SRX7022U REMOTE CONTROL
* When you press one of these buttons, the remote control operation mode appears on
the display window.
Buttons on the Remote Control
FM/AM
CD
PHONO
TAPE/CDR
DVD
DVD MULTI
Remote Control Operation Mode
TUNER
CD
PHONO
TAPE
DVD
DVD
Buttons on the Remote Control
TV/DBS
VCR
CATV/DBS CONTROL
CONTROL
SOUND
Remote Control Operation Mode
TV
VCR
DBS
VCR or TAPE
or CDDSC
SOUND
2
EN01-09.RX-7020V[A]3
2
02.4.17, 5:14 PM
Getting Started
Before Installation
General Precautions
• DO NOT insert any metal object into the unit.
• DO NOT disassemble the unit or remove screws, covers, or
cabinet.
• DO NOT expose the unit to rain or moisture.
Putting Batteries in the Remote Control
Before using the remote control, put two supplied batteries first.
• When using the remote control, aim the remote control directly at
the remote sensor on the unit.
1 On the back of the remote control, remove the
battery cover.
Locations
• Install the unit in a location that is level and protected from
moisture.
• The temperature around the unit must be between –5˚C and 35˚C
• Make sure there is good ventilation around the unit. Poor
ventilation could cause overheating and damage the unit.
Handling the unit
• DO NOT touch the power cord with wet hands.
• DO NOT pull on the power cord to unplug the cord. When
unplugging the cord, always grasp the plug so as not to damage
the cord.
• Keep the power cord away from the connecting cords and the
antenna. The power cord may cause noise or screen interference. It
is recommended to use a coaxial cable for antenna connection,
since it is well-shielded against interference.
• When a power failure occurs, or when you unplug the power cord,
the preset settings such as preset FM/AM channels and sound
adjustments may be erased in a few days.
2 Insert batteries.
• Make sure to match the polarity: (+) to (+) and (–) to (–).
Checking the Supplied Accessories
Check to be sure you have all of the following supplied accessories.
The number in the parentheses indicates the quantity of the pieces
supplied.
3 Replace the cover.
• Remote Control (1)
• Batteries (2)
• AM Loop Antenna (1)
• FM Antenna (1)
If anything is missing, contact your dealer immediately.
If the range or effectiveness of the remote control decreases, replace
the batteries. Use two R6P(SUM-3)/AA(15F) type dry-cell batteries.
CAUTION:
Follow these precautions to avoid leaking or cracking cells:
• Place batteries in the remote control so they match the polarity:
(+) to (+) and (–) to (–).
• Use the correct type of batteries. Batteries that look similar may
differ in voltage.
• Always replace both batteries at the same time.
• Do not expose batteries to heat or flame.
3
EN01-09.RX-7020V[A]3
3
02.4.17, 5:14 PM
Connecting the FM and AM Antennas
AM Loop Antenna
(supplied)
Outdoor FM antenna (not supplied)
If FM reception is poor, connect outdoor FM
antenna.
or
75
FMAXIAL
CO
CO
Standard type
outdoor FM antenna
(not supplied)
Supplied FM
antenna
ANTENNA
75
FMAXIAL
FM 75
COAXIAL
FM antenna (supplied)
Extend the supplied FM antenna horizontally.
Snap the tabs on the loop
into the slots of the base
to assemble the AM loop
antenna.
AM
LOOP
AM
EXT
If AM reception is poor, connect
outdoor single vinyl-covered wire
(not supplied).
1
2
3
R
PR/C
B
PB/C
2
Y
NT
FROKERS
EA
SP
IDEO T
TV
EN R OU
ON
O
MP ONIT
CO
M
1
D
DV
NA
TEN FM 75IAL
AN
AX
CO
AV NK-III
U LI
MP
-4
CO
NK
U LI O)
MP HR
CO(SYNC
DIO LEFT
AU
L2
ITA
DIG
( CD
(
L3
ITA
DIG
AL
IGIT
4(
TV
B
SUFER
O
WO
INY)
(PLA
T
OU )
FER
OO
BW
SU OUT
INY)
(PLA
L IN
ITA
DIG
TER
CEN
S
DB
LEFT
AR
RE
T
RIGH
EC
) (R
CDR VCR
D L
TA
DIGI
LBY
DOPCM
/ S
/ DT
AM antenna connection
T
ON
FR
) OUT
)
(RECE
TAPR
/CD
)
V
INY)
(PLA
+
–
+
–
E
NC
EDA
IMP 6
1
KER
SPEA : 8 32
N: 2
6
TIO
CAU 1 OR 2 :1
ND
1 A
–
T
RIGH
LEFT
LEFT
AM
EXIT
AM
OP
LO
T
OU )
(REC R
C
T
RIGH
CD
R
REAERS
EAK
SP
TER
CEN KER
EA
SP
+
OR
NIT
MOOUT
D
DV
L 1 ONO
ITA ) PH
DIG(DVD
S
DB
+
–
T
RIGH
CE
AN
N : ED
TIO IMP
CAU KER
SPEA
8
16
DEO
S-VI
EO
VID
EO
VID
LEFT
TV D
T
UN GH
SO BS RI AUDIO
/D
PCM
TAL/
DIGITS
LBY /D OUT
DO
L
ITA
DIG
Connect the supplied AM loop antenna to the AM LOOP
terminals.
Turn the loop until you have the best reception.
• If the reception is poor, connect an outdoor single vinylcovered wire (not supplied) to the AM EXT terminal. (Keep the
AM loop antenna connected.)
FM antenna connection
Notes:
Connect the supplied FM antenna to the FM 75 Ω COAXIAL
terminal as temporary measure.
Extend the supplied FM antenna horizontally.
• If the reception is poor, connect an outdoor FM antenna (not
supplied). Before attaching a 75 Ω coaxial cable (with a
standard type connector), disconnect the supplied FM antenna.
• If the AM loop antenna wire is covered with vinyl,
remove the vinyl while twisting it as shown to the
right.
• Make sure the antenna conductors do not touch any
other terminals, connecting cords and power cord.
This could cause poor reception.
4
EN01-09.RX-7020V[A]3
4
02.4.17, 5:15 PM
Getting Started
“NO” for the subwoofer, “LARGE” for the front speakers,
and “SMALL” for the center and rear speakers are initial
settings. To get best possible sound, change the subwoofer and
speaker settings to fit your listening conditions.
Connection diagram
FRONT
SPEAKERS
1
Connecting the Speakers
Speaker layout diagram
FRONT
SPEAKERS
1
Center
speaker
Left front
speaker
Subwoofer
Right front
speaker
2
+
+
–
–
RX-7020V AUDIO/VIDEO CONTROL RECEIVER
FM/AM TUNING
FM/AM PRESET
FM MODE
STANDBY
MASTER VOLUME
COMPULINK
Remote
MEMORY
RIGHT
D I G I T A L
SURROUND
SURROUND ON/OFF
INPUT
ANALOG/DIGITAL
BASS BOOST
ADJUST SETTING
DVD MULTI
DVD
VCR
TAPE/CDR
PHONO
TV SOUND/DBS
INPUT ATT
SOURCE NAME
SURROUND MODE
CONTROL
DOWN
UP
SPEAKERS ON/OFF
1
2
CD
LEFT
FM/AM
SOURCE NAME
PHONES
RIGHT
Left rear
speaker
LEFT
Right rear
speaker
After connecting the front, center, rear speakers and/or subwoofer,
set the speaker setting information properly to obtain the best
possible Surround effects. For details, see pages 16 to 18.
CAUTION:
Use speakers with the SPEAKER IMPEDANCE indicated by the
speaker terminals.
FRONT
SPEAKERS
2
Connecting speakers to the FRONT SPEAKERS 1 terminals
1
2
3
4
1
Connecting the front speakers
RIG
HT
LE
The required speaker impedance of the front speakers does differ
depending on whether both the FRONT SPEAKERS 1 and FRONT
SPEAKERS 2 terminals are used or only one of them is used.
CASE 1 When you connect only one pair of front speakers
Front
speaker
1
Front
speaker
1
HT
LE
LE
FT
About the speaker impedance
RIG
RIG
HT
You can connect two pairs of front speakers (one pair to the FRONT
SPEAKERS 1 terminals, and the other pair to the FRONT
SPEAKERS 2 terminals).
1
1
FT
FT
For each speaker, connect the (+) and (–) terminals on the rear panel
to the (+) and (–) terminals marked on the speakers.
1 Cut, twist and remove the insulation at the end of
each speaker signal cable (not supplied).
2 Turn the knob counterclockwise.
3 Insert the speaker signal cable.
4 Turn the knob clockwise.
Connecting speakers to the FRONT SPEAKERS 2 terminals
1
2
3
1
2
Use front speakers with 8 Ω – 16 Ω impedance.
CASE 2 When you connect two pairs of front speakers
Front
speaker
2
Front
speaker
1
Front
speaker
2
For each speaker, connect the (+) and (–) terminals on the rear panel
to the (+) and (–) terminals marked on the speakers.
Front
speaker
1
Use front speakers with 16 Ω – 32 Ω impedance.
1 Cut, twist and remove the insulation at the end of
each speaker cord.
2 Open the terminal (1), then insert the speaker
cord (2).
3 Close the terminal.
5
EN01-09.RX-7020V[A]3
5
02.4.17, 5:15 PM
Connecting Audio/Video Components
Connecting the rear and center speakers
Connect rear speakers to the REAR SPEAKERS terminals and a
center speaker to the CENTER SPEAKER terminals.
You can connect the following audio/video components to this unit.
Refer also to the manuals supplied with your components.
Center
speaker
CENTER
SPEAKER
Audio Components
• Turntable
• CD player*
• Cassette deck
or CD recorder*
REAR
SPEAKERS
+
Left rear
speaker
Turn the power off to all components before connections.
Right rear
speaker
Video Components
• VCR
• TV*
or DBS tuner*
• DVD player*
* You can connect these components using the methods described in
“Analog connections” (below) or in “Digital connections” (see page 9).
–
RIGHT
Analog connections
Audio component connections
LEFT
Use the cables with RCA pin plugs (not supplied).
Connect the white plug to the audio left jack, and the red plug to the
audio right jack.
2
1
CAUTION:
4
3
1
1
RIG
RIG
HT
LE
FT
If you connect a sound-enhancing device such as a graphic equalizer
between the source components and this receiver, the sound output
through this receiver may be distorted.
1
RIG
HT
HT
LE
LE
FT
FT
For each speaker, connect the (+) and (–) terminals on the rear panel
to the (+) and (–) terminals marked on the speakers.
Turntable
If an earth cable is provided for your
turntable, connect the cable to the
AM LOOP(H) terminal on the rear
panel.
1 Cut, twist and remove the insulation at the end of
each speaker signal cable (not supplied).
2 Turn the knob counterclockwise.
3 Insert the speaker signal cable.
4 Turn the knob clockwise.
Turntable
PHONO
Connecting the subwoofer speaker
By connecting a subwoofer, you can enhance the bass or reproduce
the original LFE signals recorded in the digital software.
CD
To audio
output
RIGHT
OUT
(REC)
TAPE
CDR
AUDIO
LEFT
IN
(PLAY)
FRONT
Powered subwoofer
DVD
SUB
WOOFER
CENTER
REAR
RIGHT
Ex.: This connection is for the
turntable with an MM (movingmagnet) type cartridge.
OUT
(REC)
VCR
IN
(PLAY)
TV
SOUND
DBS
LEFT
RIGHT
Note:
SUBWOOFER
OUT
Connect the input jack of a powered subwoofer to the
SUBWOOFER OUT jack on the rear panel, using a cable with RCA
pin plugs (not supplied).
• Refer also to the manual supplied for your subwoofer.
LEFT
AUDIO
Any turntables incorporating a small-output cartridge such as an MC
(moving-coil) type must be connected to this receiver through a
commercial head amplifier or step-up transformer. Direct connection
may result in insufficient volume.
Since bass sound is non-directional, you can place a
subwoofer wherever you like. Normally place it in front of
you.
6
EN01-09.RX-7020V[A]3
6
02.4.17, 5:15 PM
Getting Started
Video component connections
CD player
Use the cables with RCA pin plugs (not supplied).
Connect the white plug to the audio left jack, the red plug to the
audio right jack, and the yellow plug to the video jack.
• If video components have S-video (Y/C-separation) and/or
component video (Y, PB/CB, PR/CR) terminals, connect them using
an S-video cable (not supplied) and/or component video cable (not
supplied). By using these terminals, you can get a better picture
quality in the order — Component video > S-video > Composite
video.
PHONO
CD player
CD
OUT
(REC)
TAPE
CDR
To audio output
IN
(PLAY)
OUT
(REC)
VCR
IN
(PLAY)
IMPORTANT:
TV
SOUND
DBS
RIGHT
LEFT
AUDIO
Cassette deck or CD recorder
Cassette deck
To audio input
To audio output
This unit is equipped with the following video terminals; composite
video, S-video and component video terminals. You can use any of
these three to connect a video component.
However, remember that the video signals from one type of these
input terminals are output only through the video output
terminals of the same type.
Therefore, if a recording video component and a playing video
component are connected to the unit through the different types of
video terminals, you cannot record the picture from the playing
component onto the recording component. In addition, if the TV and a
playing video component are connected to the unit through the
different types of video terminals, you cannot view the playback
picture from the playing component on the TV.
PHONO
VCR
CD
OUT
(REC)
S-VHS (or VHS) VCR
TAPE
CDR
A
C
D
IN
(PLAY)
B
OUT
(REC)
E
F
VCR
PHONO
IN
(PLAY)
TV
SOUND
DBS
CD
RIGHT
LEFT
RIGHT
TAPE
CDR
CD recorder
DVD
DVD
To audio output
OUT
(REC)
SUB
WOOFER
VCR
OUT
(REC)
CENTER
VCR
REAR
IN
(PLAY)
RIGHT
IN
(PLAY)
LEFT
TV
SOUND
DBS
Note:
You can connect either a cassette deck or a CD recorder to the TAPE/
CDR jacks. When connecting a CD recorder to the TAPE/CDR jacks,
change the source name, which will be shown on the display when
selected as the source. See page 11 for details.
If your audio components have a COMPU LINK jack
See also page 31 for detailed information about the connection and
the COMPU LINK remote control system.
DBS
RIGHT
LEFT
AUDIO
Å
ı
Ç
Î
‰
Ï
SUBWOOFER
OUT
7
VIDEO
To left/right channel audio output
To left/right channel audio input
To composite video output
To S-video output
To S-video input
To composite video input
7
EN01-09.RX-7020V[A]3
LEFT
FRONT
IN
(PLAY)
To audio input
MONITOR
OUT
AUDIO
OUT
(REC)
AUDIO
02.4.17, 5:15 PM
VIDEO
S-VIDEO
DVD player
TV and/or DBS tuner
• When you connect the DVD player with stereo output jacks:
PHONO
Y
COMPONENT VIDEO
MONITOR OUT
PB/CB
PR/CR
DVD player
D
CD
OUT
(REC)
MONITOR
OUT
AUDIO
RIGHT
TAPE
CDR
DVD
DVD
C
LEFT
FRONT
IN
(PLAY)
B
A
DBS
DVD
DVD
SUB
WOOFER
OUT
(REC)
VCR
CENTER
OUT
(REC)
VCR
REAR
IN
(PLAY)
RIGHT
TV
SOUND
DBS
LEFT
SUBWOOFER
OUT
MONITOR
OUT
AUDIO
AUDIO
S-VIDEO
VIDEO
VIDEO
PR/CR
MONITOR OUT
DBS
RIGHT
PB/CB
Y
COMPONENT VIDEO
IN
(PLAY)
LEFT
RIGHT
DVD
LEFT
DBS
DVD
FRONT
DVD
SUB
WOOFER
B
TV
OUT
(REC)
CENTER
VCR
C
REAR
IN
(PLAY)
RIGHT
LEFT
DBS
A
Å
ı
Ç
Î
D
SUBWOOFER
OUT
Å
ı
Ç
Î
To audio output
To composite video input
To S-video input
To component video input
COMPONENT VIDEO
MONITOR OUT
PHONO
VIDEO
Y
PB/CB
PR/CR
S-VIDEO
VIDEO
To front left/right channel audio output
To composite video output
To S-video output
To component video output
• When you connect the DVD player with its analog discrete output
(5.1 CH reproduction) jacks:
CD
MONITOR
OUT
OUT
(REC)
DVD
AUDIO
TAPE
CDR
RIGHT
IN
(PLAY)
DBS
LEFT
DVD player
A
G
DVD
FRONT
DVD
DVD
OUT
(REC)
SUB
WOOFER
VCR
CENTER
VCR
B
IN
(PLAY)
REAR
IN
(PLAY)
RIGHT
F
E
OUT
(REC)
C
D
LEFT
TV
SOUND
DBS
DBS
RIGHT
LEFT
AUDIO
VIDEO
VIDEO
COMPONENT VIDEO
MONITOR OUT
S-VIDEO
SUBWOOFER
OUT
MONITOR
OUT
AUDIO
RIGHT
A
DBS tuner
B
LEFT
Y
PB/CB
PR/CR
DVD
DBS
DVD
FRONT
DVD
SUB
WOOFER
DBS
C
OUT
(REC)
CENTER
VCR
REAR
D
RIGHT
IN
(PLAY)
LEFT
DBS
Å
ı
Ç
Î
To audio output
To composite video output
To S-video output
To component video output
Notes:
• When connecting the DBS tuner to the TV SOUND/DBS jacks,
change the source name, which will be shown on the display when
selected as the source, to “DBS.” See page 11 for details.
• When operating the DBS tuner by using the AV COMPU LINK
remote control system, change the video input terminal setting
correctly. See pages 11 and 32 for details.
SUBWOOFER
OUT
Å
ı
Ç
Î
‰
Ï
Ì
VIDEO
VIDEO
S-VIDEO
To rear left/right channel audio output
To subwoofer audio output
To front left/right channel audio output
To center channel audio output
To composite video output
To S-video output
To component video output
8
EN01-09.RX-7020V[A]3
8
02.4.17, 5:15 PM
Getting Started
Digital connections
Notes:
This receiver is equipped with four DIGITAL IN terminals—one
digital coaxial terminal and three digital optical terminals, and one
DIGITAL OUT terminal.
You can connect any digital equipments such as—:
• DBS tuner,
• Digital TV broadcast tuner,
• DVD player,
• CD player, and
• CD recorder.
• When shipped from the factory, the DIGITAL IN terminals have
been set for use with the following components:
– DIGITAL 1 (coaxial): For DVD player
– DIGITAL 2 (optical): For CD player
– DIGITAL 3 (optical): For digital TV broadcast tuner
– DIGITAL 4 (optical): For CD recorder
• When you want to operate the CD player or CD recorder using the
COMPU LINK remote control system, connect the target
component also as described in “Analog connections” (see page 7).
• When you want to operate the DVD player using the AV COMPU
LINK remote control system, connect the DVD player also as
described in “Analog connections” (see page 8).
IMPORTANT:
• When connecting the DVD player, digital TV broadcast tuner or DBS
tuner using the digital terminals, you also need to connect it to the
video jack on the rear. Without connecting it to the video jack, you
can view no playback picture.
• After connecting the components using the DIGITAL IN terminals,
set the following correctly if necessary:
– Set the digital input (DIGITAL IN) terminal setting correctly. For
details, see “Setting the Digital Input (DIGITAL IN) Terminals” on
page 14.
– Select the digital input mode correctly. For details, see “Selecting
the Analog or Digital Input Mode” on page 15.
Digital output terminal
This terminal can output the same type of incoming signals Dolby
Digital, Linear PCM, and DTS.
CD recorder, etc.
Digital input terminals
Digital TV
Digital optical cable (not supplied)
between digital optical terminals
DBS tuner
DBS
DVD player
When the digital recording
equipment such as a CD recorder
has a digital optical input terminal,
connect it to the DIGITAL OUT
terminal enables you to perform
digital-to-digital recording.
DVD
CD player
CD recorder
DOLBY DIGITAL/PCM
/DTS
DIGITAL OUT
Digital coaxial cable (not supplied)
between digital coaxial terminals
Connecting the Power Cord
Before plugging the receiver into an AC outlet, make sure that all
connections have been made.
Digital optical cable (not supplied)
between digital optical terminals
Plug the power cord into an AC outlet.
Keep the power cord away from the connecting cables and the
antenna. The power cord may cause noise or screen interference. We
recommend that you use a coaxial cable to connect the antenna,
since it is well-shielded against interference.
When the component has a digital
coaxial output terminal, connect it to the
DIGITAL 1 (DVD) terminal, using the
digital coaxial cable (not supplied).
When the component has a digital
optical output terminal, connect it to the
DIGITAL 2 (CD), DIGITAL 3 (TV), or
DIGITAL 4 (CDR) terminal, using the
digital optical cable (not supplied).
Before connecting a digital
optical cable, unplug the
protective plug.
DIGITAL 1
(DVD)
DIGITAL 2 ( CD )
CAUTIONS:
• Do not plug in before setting the voltage selector switch on the rear
of the unit and all connection procedures are completed.
• Do not touch the power cord with wet hands.
• Do not pull on the power cord to unplug the cord. When unplugging
the cord, always grasp the plug so as not to damage the cord.
DIGITAL 3 ( TV )
DIGITAL 4 (CDR)
DOLBY DIGITAL
/PCM
/DTS
DIGITAL IN
9
EN01-09.RX-7020V[A]3
9
02.4.17, 5:15 PM
Basic Operations
Front Panel
Remote Control
STANDBY lamp
Display
A/V CONTROL RECEIVER
RX-7022V AUDIO/VIDEO CONTROL RECEIVER
FM/AM TUNING
FM/AM PRESET
FM MODE
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
STANDBY
MEMORY
SPK 1 2
L
C
BASS BOOST
TUNED STEREO
S
Source
Selecting
Buttons
AUTO MUTING SLEEP
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
R
VOLUME
S.WFR LFE
LS
MASTER VOLUME
RS
CH-
STANDBY/ON
SURROUND ON/OFF
INPUT
ANALOG/DIGITAL
BASS BOOST
VCR
VCR
DVD
DVD MULTI
CD
FM/AM
TV/DBS
VCR
TAPE/CDR
PHONO
−
BASS
SURROUND
ADJUST SETTING
DVD
DVD MULTI
CATV/DBS
ON/OFF
TV SOUND/DBS
+
TV
−
CONTROL
DOWN
UP
SPEAKERS ON/OFF
1
1
2
CD
TAPE/CDR
2
SLEEP
3
MENU
SOUND
DIMMER
MUTING
FM/AM
PHONO
+
– CENTER +
BASS BOOST EFFECT
SOURCE NAME
SLEEP
INPUT
INPUT ATT
SURROUND MODE
TREBLE
SURROUND ANALOG/DIGITAL
MODE
AUDIO
AUDIO
SOURCE NAME
PHONES
– REAR • L +
TEST
4
5
6
ENTER
DIMMER
– REAR • R +
7/P
9
10
0
+10
RETURN
FM MODE
100+
CATV/DBS
CONTROL
TV/VIDEO
8
– SUB WOOFER +
MUTING
+
+
+
CH
TV VOL
VOLUME
−
−
VOLUME
+/–
−
+
PHONES
jack
Source SOURCE
Selecting NAME
Buttons
SPEAKERS
ON/OFF
STANDBY/ON
Turning On the Power
Press STANDBY/ON
(or AUDIO
MASTER
VOLUME
TUNING
/REW
FF/
−
REC
PAUSE
CONTROL
RM-SRX7022U REMOTE CONTROL
Selecting the Source to Play
on the remote control).
Press one of the Source Selecting Buttons. The selected source name
appears on the display.
STANDBY
AUDIO
DVD MULTI
DVD
VCR
TV SOUND/DBS
SOURCE NAME
STANDBY/ON
CD
On the front panel
TAPE/CDR
From the remote control
The STANDBY lamp goes off. The name of the current source (or
station frequency) appears on the display.
PHONO
DVD
DVD MULTI
TV/DBS
VCR
CD
FM/AM
TAPE/CDR PHONO
FM/AM
SOURCE NAME
On the front panel
From the remote control
Current source name appears
DVD MULTI
ANALOG
SPK 1
L
C
R
VOLUME
S.WFR LFE
LS
S
RS
CH-
Current volume level is shown here
To turn off the power (into standby mode)
(or AUDIO
on
Press STANDBY/ON
the remote control) again.
The STANDBY lamp lights up.
STANDBY
STANDBY/ON
: Select the DVD player for viewing the digital video
disc using the analog discrete output mode (5.1 ch
reproduction).
To enjoy the DVD MULTI playback, see page 30.
DVD
: Select the DVD player.
VCR
: Select the VCR.
TV SOUND/DBS
: Select the TV sound (or the DBS tuner).
CD *
: Select the CD player.
TAPE/CDR * : Select the cassette deck (or the CD recorder).
PHONO *
: Select the turntable.
FM/AM *
: Select an FM or AM broadcast.
• Each time you press the button, the band
alternates between FM and AM.
Note:
Notes:
A small amount of power is consumed in standby mode. To turn the
power off completely, unplug the AC power cord.
• When connecting a CD recorder (to the TAPE/CDR jacks) or a DBS
tuner (to the TV SOUND/DBS jacks), change the source name that
appears on the display. See “Changing the source name” on page
11.
• When you have connected some digital source components using
the digital terminals (see page 9), you need to select the digital
input mode (see page 15).
• When you press one of the source selecting buttons on the remote
control marked above with asterisks (*), the receiver automatically
turns on.
10
EN10-22.RX-7020V[A]3
10
02.4.17, 5:15 PM
Basic Operations
Adjusting the Volume
Changing the source name
Remote
NOT
When you have connected a CD recorder to the
TAPE/CDR jacks or the DBS tuner to the TV
SOUND/DBS jacks on the rear panel, change the
source name which will be shown on the display.
MASTER VOLUME
When changing the source name from “TAPE” to “CDR”:
1
2
Press TAPE/CDR (SOURCE NAME)
to select “TAPE” as the source.
Press and hold SOURCE NAME
(TAPE/CDR) to assign “CDR.”
On the front panel:
To increase the volume,
turn MASTER VOLUME clockwise.
To decrease the volume,
turn it counterclockwise.
TAPE/CDR
SOURCE NAME
From the remote control:
To increase the volume, press VOLUME +.
To decrease the volume, press VOLUME –.
TAPE/CDR
+
VOLUME
−
SOURCE NAME
CAUTION:
When changing the source name from “TV SOUND” to “DBS”:
1
2
Press TV SOUND/DBS (SOURCE
NAME) to select “TV SOUND” as
the source.
Press and hold SOURCE NAME
(TV SOUND/DBS) to assign “DBS.”
Always set the volume to the minimum before starting any source. If
the volume is set at its high level, the sudden blast of sound energy
can permanently damage your hearing and/or ruin your speakers.
TV SOUND/DBS
SOURCE NAME
Note:
The volume level can be adjusted within the range of “0” (minimum) to
“50” (maximum).
TV SOUND/DBS
SOURCE NAME
Selecting the Front Speakers
To change the source name to “TAPE” or “TV SOUND,” repeat
the same procedure above.
Notes:
• To watch the picture from DBS tuner, change the source name to
“DBS.” If “TV SOUND” is selected, you cannot watch the picture
from DBS tuner.
• Without changing the source name, you can still use the connected
components. However, there may be some inconvenience.
– “TAPE” or “TV SOUND” will appear on the display when you
select the CD recorder or DBS tuner.
– You cannot use the digital input (see page 15) for the CD
recorder.
– You cannot use the COMPU LINK remote control system (see
page 31) to operate the CD recorder.
Selecting different sources for picture and sound
You can watch picture from a video component while listening to
sound from another component.
Press one of the audio source selecting buttons —
CD, TAPE/CDR, PHONO, FM/AM, while watching the picture
from a video component such as the VCR, DVD player, or DBS
tuner, etc.
DVD MULTI
DVD
VCR
TV SOUND/DBS
DVD
DVD MULTI
CD
FM/AM
TV/DBS
VCR
TAPE/CDR
PHONO
SOURCE NAME
CD
TAPE/CDR
PHONO
FM/AM
SOURCE NAME
On the front panel
From the remote control
Notes:
• Once you have selected a video source, pictures of the selected
source are sent to the TV until you select another video source.
• This function can use only when selecting the S-video or composite
video input terminal.
When you have connected two pairs of the front speakers, you can
select which to use.
SPEAKERS ON/OFF
1
11
2
To use the speakers connected to the FRONT SPEAKERS 1
terminals, press SPEAKERS ON/OFF 1 so that the SPK 1 indicator
lights up on the display. (Make sure that the SPK 2 is not lit on the
display.)
To use the speakers connected to the FRONT SPEAKERS 2
terminals, press SPEAKERS ON/OFF 2 so that the SPK 2 indicator
lights up on the display. (Make sure that the SPK 1 is not lit on the
display.)
To use both sets of the speakers, press SPEAKERS ON/OFF 1 and 2
so that the SPK 1 and SPK 2 indicators light up on the display.
To use neither sets of the speakers, press SPEAKERS ON/OFF
1 and 2 so that the SPK 1 and SPK 2 indicators disappear from the
display.
Notes:
• If you select any of the Surround modes while using both the
speakers connected to the FRONT SPEAKERS 1 and 2
terminals, the speakers connected to the FRONT SPEAKERS 2
terminals are deactivated.
• While the Surround mode is in use, you can only select either the
speakers connected to the FRONT SPEAKERS 1 or 2 terminals.
• If you select the source to DVD MULTI while using both the
speakers connected to the FRONT SPEAKERS 1 and 2
terminals, the speakers connected to the FRONT SPEAKERS 2
terminals are deactivated.
• When selecting “DVD MULTI” as the source, you can only select
either the speakers connected to the FRONT SPEAKERS 1 or 2
terminals.
11
EN10-22.RX-7020V[A]3
Remote
NOT
02.4.17, 5:15 PM
Listening Only with Headphones
Changing the Display Brightness
You must turn off both pairs of speakers when you listen with
headphones.
You can dim the display.
1 Connect a pair of headphones to the PHONES jack on the front
Press DIMMER on the remote control.
• Each time you press the button, the display dims and
brightens alternately.
panel.
DIMMER
2 Press SPEAKERS ON/OFF 1 and SPEAKERS ON/OFF 2 so
that neither the SPK 1 nor SPK 2 indicator appears on the
display.
• “HEADPHONE” appears and H. PHONE indicator lights up
on the display.
Turning Off the Power
with the Sleep Timer
ANALOG
L
R
H.PHONE
You can fall asleep while listening to music—Sleep Timer.
This cancels the Surround modes currently selected and
activates the HEADPHONE mode (see below).
HEADPHONE mode
When using the headphones, following signals are output
regardless of your speaker setting:
— For 2 channel sources, the front left, right channel signals are
output directly from the headphones.
— For multichannel sources, the front left and right, center, and
rear channel signals are down-mixed and then output from the
headphones.
You can enjoy multichannel sound sources using the
headphones.
Notes:
• While in the HEADPHONE mode, you cannot use any Surround
modes (see page 23).
• Activating the speakers cancels the HEADPHONE mode and turns
on the Surround modes previously selected.
CAUTION:
Be sure to turn down the volume
• Before connecting or putting on headphones, as high volume can
damage both the headphones and your hearing.
• Before turning on speakers again, as high volume may output from
the speakers.
Press SLEEP on the remote control repeatedly.
• The SLEEP indicator lights up on the display and the
shut-off time changes in 10 minutes intervals.
ANALOG
SPK 1
L
C
SLEEP
SLEEP
R
S.WFR LFE
LS
S
RS
CH-
10
20
30
40
50
60
0 (Canceled)
90
80
70
When the shut-off time comes
The receiver turns off automatically.
To check or change the remaining time until the shut-off time
Press SLEEP once.
The remaining time (in minutes) until the shut-off time appears.
• To change the shut-off time, press SLEEP repeatedly.
To cancel the Sleep Timer
Press SLEEP repeatedly until “SLEEP 0 MIN” appears on the
display. (The SLEEP indicator goes off.)
• Turning off the power also cancels the Sleep Timer.
Turning Off the Sounds
Temporarily—Muting
You can turn off the volume temporarily.
MUTING
Press MUTING on the remote control to mute
the sound through all speakers and headphones
connected.
• “MUTING” appears on the display and the volume turns off (the
volume level indicator goes off).
ANALOG
SPK 1
L
C
R
S.WFR LFE
LS
S
RS
CH-
To restore the sound, press MUTING again.
• Turning MASTER VOLUME on the front panel or pressing
VOLUME +/– on the remote control also restores the sound.
12
EN10-22.RX-7020V[A]3
12
02.4.17, 5:15 PM
Basic Operations
Basic adjustment auto memory
Signal and speaker indicators on the display
This receiver memorizes sound settings for each source when—:
• you turn off the power,
• you change the source, and
• you assign the source name.
Signal indicators
When you change the source, the memorized settings for the
newly selected source are automatically recalled.
The following can be stored for each source:
• Input attenuator mode (see page 19)
• Balance (see page 19)
• Tone adjustment (see page 20)
• Subwoofer output level (see page 20)
• Surround mode selection (see pages 26 – 29)
• Bass boost (see page 20)
Notes:
• You cannot assign and store different settings for digital input
mode and analog input mode.
• If the source is FM or AM, you can assign a different setting for
each band.
For recording
For analog-to-analog recording
You can record any analog source through the receiver to—:
• the cassette deck (or CD recorder) connected to the TAPE/CDR
jacks, and
• the VCR connected to the VCR jacks at the same time.
For digital-to-digital recording
You can record the currently selected digital input through the
receiver to a digital recording device connected to the DIGITAL
OUT terminal.
L
C
R
S.WFR LFE
LS
S
Speaker indicators
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
RS
C
S
R
RS
PRO LOGIC ΙΙ
L
C
R
CH-
S.WFR LFE
LS
S
RS
The speaker indicators light up when—:
• The corresponding speaker is activated, and
• The corresponding speaker is required for the current playback.
Notes:
• When you select “DVD MULTI,” all the signal indicators except “S”
light up.
• When “SUBWOOFER” is set to “YES” (see page 16), S.WFR
lights up.
• Analog-to-digital and digital-to-analog recordings are not
possible.
• The output volume level, bass boost (see page 20), tone
adjustment (see page 20), and Surround modes (see page 23)
cannot affect the recording.
• The test tone signal (see pages 26 and 27) does not come out
through the DIGITAL OUT terminal.
13
13
L
The following signal indicators light up—:
L : •When digital input is selected: Lights up when the left
channel signal comes in.
• When analog input is selected: Always lights up.
R : • When digital input is selected: Lights up when the right
channel signal comes in.
• When analog input is selected: Always lights up.
C : When the center channel signal comes in.
LS : When the left rear channel signal comes in.
RS : When the right rear channel signal comes in.
S : When the monaural rear channel signal or 2 ch Dolby
Digital Surround encoded signal comes in.
LFE: When the LFE channel signal comes in.
Notes:
EN10-22.RX-7020V[A]3
SPK 1 2
S.WFR LFE
LS
02.4.17, 5:15 PM
Basic Settings
Front Panel
Remote Control
Display
SETTING
A/V CONTROL RECEIVER
RX-7022V AUDIO/VIDEO CONTROL RECEIVER
FM/AM TUNING
FM/AM PRESET
Source
Selecting
Buttons
FM MODE
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
STANDBY
MEMORY
SPK 1 2
L
C
R
BASS BOOST
TUNED STEREO
AUTO MUTING SLEEP
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
VOLUME
S.WFR LFE
LS
S
MASTER VOLUME
RS
CH-
STANDBY/ON
CATV/DBS
VCR
DVD
DVD MULTI
CD
FM/AM
TV/DBS
VCR
TAPE/CDR
PHONO
−
BASS
SURROUND
ON/OFF
INPUT
ANALOG/DIGITAL
SURROUND ON/OFF
−
+
MODE
ADJUST SETTING
DVD MULTI
DVD
VCR
1
CD
TAPE/CDR
PHONO
+
SLEEP
– CENTER +
2
3
MENU
SOUND
– REAR • L +
TEST
4
5
7/P
8
6
ANALOG/
DIGITAL
INPUT
ENTER
DIMMER
CONTROL
DOWN
UP
2
TREBLE
INPUT
1
TV SOUND/DBS
SOURCE NAME
SPEAKERS ON/OFF
AUDIO
SURROUND ANALOG/DIGITAL
BASS BOOST EFFECT
BASS BOOST
INPUT ATT
SURROUND MODE
TV
FM/AM
– REAR • R +
SOURCE NAME
9
– SUB WOOFER +
MUTING
10
0
+10
RETURN
FM MODE
100+
CATV/DBS
CONTROL
PHONES
TV/VIDEO
+
+
+
CH
TV VOL
VOLUME
−
−
−
+
TUNING
/REW
FF/
−
INPUT
ANALOG/DIGITAL
Source
Selecting
Buttons
Setting the Digital Input
[DIGITAL IN] Terminals
REC
PAUSE
CONTROL
RM-SRX7022U REMOTE CONTROL
CONTROL
UP 5/DOWN ∞
Remote
NOT
When the DIGITAL 1 terminal is set, the DIGITAL 2/3/4
terminals are set automatically as follows:
When the DIGITAL 1 is set to “DVD”
When you use the digital input terminals, you have to register what
components are connected to which terminals (DIGITAL IN 1/2/3/4).
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
2 CD 3 TV (or DBS*) 4 CDR
When the DIGITAL 1 is set to “CD”
2 DVD 3 TV (or DBS*) 4 CDR
When the DIGITAL 1 is set to “TV” or “DBS”
2 DVD 3 CD 4 CDR
To set the DIGITAL 1 terminal
1
Press SETTING repeatedly until
“COAX DIGI IN” appears on the
display.
T SETTING
When the DIGITAL 1 is set to “CDR”
2 DVD 3 CD 4 TV (or DBS*)
* If you have changed the source name from “TV SOUND” to
“DBS,” “DBS” appears (see page 11).
SPK 1
DIGITAL AUTO
L
C
R
S.WFR LFE
LS
Press SETTING repeatedly until “OPT DIGI IN” appears on the
display.
RS
S
CH-
After 2 seconds, the display changes to show the current setting.
After 2 seconds, the display changes to show the current setting.
SPK 1
DIGITAL AUTO
L
C
DIGITAL 3 terminal setting
R
S.WFR LFE
LS
S
RS
CH-
2
Press CONTROL UP 5/DOWN ∞
to select the appropriate digital
terminal setting.
CONTROL
DOWN
UP
• Each time you press the button, the display
changes as follows:
1 DVD j 1 CD j 1 TV (or 1 DBS*) j 1 CDR j
(back to the beginning)
* If you have changed the source name from “TV SOUND” to
“DBS,” “DBS” appears (see page 11).
DIGITAL 2 terminal setting
DIGITAL 4 terminal setting
Notes:
• When shipped from the factory, the DIGITAL IN terminals have
been set for use with the following components:
– DIGITAL 1 (coaxial): For DVD player
– DIGITAL 2 (optical): For CD player
– DIGITAL 3 (optical): For digital TV broadcast tuner
– DIGITAL 4 (optical): For CD recorder
• When using the DIGITAL 4 terminal for the CD recorder, you need
to select “CDR” as the source name. (See page 11.)
14
EN10-22.RX-7020V[A]3
14
02.4.17, 5:15 PM
Basic Settings
If the following symptoms occur while playing Dolby Digital
or DTS Digital Surround software with “DIGITAL AUTO”
selected, follow the procedure below:
• Sound does not come out at the beginning of playback.
• Noise comes out while searching or skipping chapters or
tracks.
Selecting the Analog or Digital Input
Mode
When you have connected digital source components using both the
analog connections (see page 6) and the digital connections (see
page 9) methods, you need to select the input mode correctly.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
1
1
INPUT
ANALOG / DIGITAL
Press one of the source selecting buttons—DVD,
TV SOUND/DBS (TV/DBS on the remote
control), CD, or TAPE/CDR*—for which you
want to change the input mode.
DVD MULTI
DVD
VCR
TV SOUND/DBS
SOURCE NAME
CD
TAPE/CDR
PHONO
DVD
DVD MULTI
CD
FM/AM
TV/DBS
VCR
TAPE/CDR
PHONO
FM/AM
SOURCE NAME
On the front panel
From the remote control
Press INPUT ANALOG/DIGITAL (or
ANALOG/ DIGITAL INPUT on the remote
control.)
ANALOG/DIGITAL
INPUT
INPUT ATT
On the front panel
2
From the remote control
Press CONTROL UP 5/DOWN ∞ to
select “DOLBY DIGITAL” or “DTS
SURROUND” while “DIGITAL
AUTO” still remains on the display.
Remote
NOT
• Each time you press the button, the digital input mode changes
as follows:
Note:
When “DOLBY DIGITAL” or “DTS SURROUND”
is selected, “DIGITAL AUTO” goes off.
* Among the sources listed above, you can select the digital input
only for the sources which you have selected the digital input
terminals for. (See “Setting the Digital Input (DIGITAL IN)
Terminals” on page 14.)
SPK
DIGITAL AUTO
L
C
R
S.WFR LFE
DIGITAL
LS
S
RS
CH-
2
Press INPUT ANALOG/DIGITAL
(or ANALOG/DIGITAL INPUT on the remote
control) to select the digital input mode.
INPUT
ANALOG / DIGITAL
ANALOG/DIGITAL
INPUT
INPUT ATT
On the front panel
From the remote control
• Each time you press the button, the input mode alternates
between the analog input (“ANALOG”) and the digital input
(“DIGITAL AUTO”).
DIGITAL AUTO : Select this for the digital input mode. The
receiver automatically detects the
incoming signal format. (The DIGITAL
AUTO indicator lights up on the display,
then the digital signal indicator for the
detected signals lights up.)
ANALOG
: Select this for the analog input mode.
(Initial setting when shipped from the
factory.)
DIGITAL AUTO
DTS SURROUND
DOLBY DIGITAL
• To play back software encoded with Dolby Digital, select
“DOLBY DIGITAL.”
• To play back software encoded with DTS Digital Surround,
select “DTS SURROUND.”
Note:
When you turn off the power or select another source, “DOLBY
DIGITAL” and “DTS SURROUND” are canceled and the digital input
mode is automatically reset to “DIGITAL AUTO.”
The followings are the analog/digital signal indicators on the display
to indicate what type of the signal comes into the receiver.
ANALOG
: Lights when the analog input is selected.
LINEAR PCM : Lights when Linear PCM signals come in.
DIGITAL : • Lights when Dolby Digital signals come in.
• Flashes when “DOLBY DIGITAL” is
selected for software not encoded with Dolby
Digital signals.
: • Lights when DTS signals come in.
• Flashes when “DTS SURROUND” is
selected for software not encoded with DTS
signals.
Note:
When “DIGITAL AUTO” cannot recognize the incoming signals, no
digital signal indicators light up on the display.
15
EN10-22.RX-7020V[A]3
15
02.4.17, 5:15 PM
Selecting the Video Input
Terminal
Remote
NOT
This receiver is equipped with the component video input terminals
for the DVD player and DBS tuner, which give you higher picture
quality. When you use the component video input terminals for the
DVD player and/or DBS tuner, change the video input terminal
setting.
“NO” for the subwoofer, “LARGE” for the front speakers,
and “SMALL” for the center and rear speakers are initial
settings. To get best possible sound, change the subwoofer and
speaker settings to fit your listening conditions.
Remote
NOT
Setting the Speaker Information
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
To obtain the best possible sound or effect from Surround modes
(see pages 26 to 29), register the following speakers and subwoofer
information after all connections are completed.
1
The followings are items you can set:
• Subwoofer information—SUBWOOFER
• Speaker size—FRNT SP, CNTR SP, REAR SP
• Speaker distance—UNIT, FRNT DIS, CNTR DIS, REAR DIS
• Crossover frequency—CROSS
• Low frequency effect attenuator—LFE ATT
• Dynamic range compression—D. COMP
Press SETTING repeatedly until
“VIDEO IN DVD ” or “VIDEO IN
DBS ” appears on the display.
ST SETTING
• Select “VIDEO IN DVD” to select the video input terminal for
the DVD player and “VIDEO IN DBS” for the DBS tuner.
SPK 1
DIGITAL AUTO
LINEAR PCM
L
C
R
CH-
After 2 seconds, the display changes to show the current setting.
2
Press CONTROL UP 5/DOWN ∞
to select the appropriate type of
the video input terminal.
CONTROL
DOWN
UP
• Each time you press the button, the display
changes as follows:
COMPONENT
S/C
(Component)
(S-video/Composite)
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
Subwoofer information
Register whether you have connected a subwoofer or not.
1
Press SETTING repeatedly until
“SUBWOOFER” (with the current
setting)* appears on the display.
ST SETTING
SPK 1
DIGITAL AUTO
LINEAR PCM
L
C
R
S.WFR LFE
CH-
COMPONENT : Select this when you connect the DVD
player or DBS tuner to the component video
input terminals.
S/C
: Select this when you connect the DVD player
or DBS tuner to the S-video or composite
video input terminal.
* “NO” is the initial setting. If you have already changed the
setting, “YES” will be shown.
2
Press CONTROL UP 5/DOWN ∞ to
register whether you have connected
a subwoofer or not.
CONTROL
DOWN
UP
• Each time you press the button, the subwoofer
setting alternates between “YES” and “NO.”
Note:
Without changing the video input terminal setting, you can see the
picture through the video input terminals, but cannot use the AV
COMPU LINK remote control system correctly (see page 32).
YES
: Select this when you have connected a subwoofer.
You can adjust the subwoofer output level
(see page 20).
NO
: Select this when you have not connected or have
disconnected a subwoofer.
16
EN10-22.RX-7020V[A]3
16
02.4.17, 5:15 PM
Basic Settings
1
Speaker size
Register the sizes of all the connected speakers.
• When you change your speakers, register the information about
the speakers again.
1
SPK 1
ST SETTING
Press SETTING repeatedly until
“FRNT SP (Front Speaker),” “CNTR
SP (Center Speaker)” or “REAR SP
(Rear Speaker)” (with the current setting)*
appears on the display.
L
C
DIGITAL AUTO
LINEAR PCM
S
R
RS
Press CONTROL UP 5/DOWN ∞ to
select the unit.
CONTROL
DOWN
UP
Press CONTROL UP 5/DOWN ∞ to
select the appropriate item about the
speaker selected in the above step.
CONTROL
DOWN
UP
METER : Speaker distance is shown in meter.
FEET
3
• Each time you press the button, the display
changes as follows:
SMALL
LARGE
LARGE : Select this when the speaker size is relatively large.
(See “Notes” below.)
SMALL : Select this when the speaker size is relatively small.
(See “Notes” below.)
: Select this when you have not connected a speaker.
(Not selectable for the front speakers)
Repeat steps 1 and 2 to select the appropriate
items for other speakers.
: Speaker distance is shown in feet.
T SETTING
Press SETTING repeatedly until
“FRNT DIS (Front distance),” “CNTR
DIS (Center distance)” or “REAR DIS
(Rear distance)” (with the current setting)*
appears on the display.
• The display shows the current setting in the unit selected in
step 2.
* “3.0m” is the initial setting for meter and “10FT” is for feet. If
you have already changed the setting, another value will be
shown.
NONE
3
R
RS
• Each time you press the button, the setting
alternates between “METER” and “FEET.”
* “LARGE” is the initial setting for the front speakers and
“SMALL” is for the center and rear speakers. If you have
already changed the setting, another size will be shown.
NONE
S
*“METER” is the initial setting. If you have already changed the
setting, “FEET” will be shown.
CH-
2
C
CH-
S.WFR LFE
LS
L
S.WFR LFE
LS
2
SPK 1
DIGITAL AUTO
LINEAR PCM
T SETTING
Press SETTING repeatedly until
“UNIT” (with the current setting)*
appears on the display.
4
Press CONTROL UP 5/DOWN ∞ to
select the appropriate speaker
distance.
CONTROL
DOWN
UP
• If you select “METER” in step 2, the value is
changed from “0.3m” to “9.0m” by 0.3 m step.
• If you select “FEET” in step 2, the value is changed from
“1FT” to “30FT” by 1 foot step.
Left front
speaker
Notes:
Center speaker
• Keep the following comment in mind as reference when adjusting.
– If the size of the cone speaker unit built in your speaker is greater
than 12 cm, select “LARGE,” and if it is smaller than 12 cm,
select “SMALL.”
• If you have selected “NO” for the subwoofer setting, you can only
select “LARGE” for the front speaker setting.
• If you have selected “SMALL” for the front speaker setting, you
cannot select “LARGE” for the center and rear speaker settings.
Right front
speaker
3.0 m
(10 feet)
2.7 m
(9 feet)
2.4 m
(8 feet)
2.1 m
(7 feet)
Left rear
speaker
Right rear
speaker
Speaker distance
Register the unit you use, then the speaker distance from your
listening point.
• If you have set the unit before, start from step 3.
• Speaker distance is not valid for the DVD MULTI playback mode.
Example: In this case,
set “FRNT DIS” to “3.0m” or “10FT,”
set “CNTR DIS” to “2.7m” or “9FT” and
set “REAR DIS” to “2.4m” or “8FT.”
Note:
If you have selected “NONE” for the center and rear speakers setting,
you cannnot set the speaker distance for the center and rear
speakers.
17
EN10-22.RX-7020V[A]3
17
02.4.17, 5:15 PM
2
Crossover frequency
Small speakers cannot reproduce the bass sounds efficiently. If you
use a small speaker in any position, this receiver automatically
reallocates the bass sound elements assigned from small speaker to
large speakers.
To use this function properly, set this crossover frequency level
according to the size of the small speaker connected.
• If you have selected “LARGE” for all speakers, this function will
not take effect.
• Crossover frequency is not valid for the DVD MULTI playback
mode and HEADPHONE mode.
Press CONTROL UP 5/DOWN ∞ to
select the low frequency effect
attenuator level.
CONTROL
DOWN
UP
• Each time you press the button, the setting
alternates between “0dB” and “–10dB.”
0dB
–10dB
: Normally select this.
: Select this when the bass sound is distorted.
Dynamic range compression
1
T
Press SETTING repeatedly until
“CROSS (Crossover)” (with the current
setting)* appears on the display.
SETTING
You can compress the dynamic range (difference between maximum
sound and minimum sound) of the reproduced sound. This is useful
when enjoying surround sound at night.
• This function takes effect only when playing back a source
encoded with Dolby Digital.
SPK 1
DIGITAL AUTO
LINEAR PCM
L
C
R
1
S.WFR LFE
LS
RS
S
CH-
* “100HZ” is the initial setting. If you have already changed the
setting, another frequency will be shown.
2
Press CONTROL UP 5/DOWN ∞ to
select the crossover frequency level
you like to use.
CONTROL
DOWN
UP
100HZ
200HZ
C
S
R
RS
CH-
* “MID” is the initial setting. If you have already changed the
setting, another setting will be shown.
120HZ
2
150HZ
Press CONTROL UP 5/DOWN ∞
to select the appropriate compression
level.
CONTROL
DOWN
UP
• Each time you press the button, the
display changes as follows:
If the bass sound is distorted while playing back software using
Dolby Digital or DTS Digital Surround, follow the procedure
below:
• Low frequency effect attenuator is not valid for DVD MULTI
playback mode.
• This function takes effect only when the subwoofer (LFE) signals
come in (with “SUBWOOFER” set to “YES”).
Press SETTING repeatedly until
“LFE ATT (Low Frequency Effect
Attenuator)” (with the current
setting)* appears on the display.
L
S.WFR LFE
LS
Low frequency effect attenuator
1
SETTING
SPK 1
DIGITAL AUTO
LINEAR PCM
• Each time you press the button, the crossover
frequency level changes as follows:
80HZ
T
Press SETTING repeatedly until
“D. COMP (Dynamic range
compression)” (with the current setting)*
appears on the display.
T SETTING
MID
OFF
MAX
OFF : Select this when you want to enjoy surround with its
full dynamic range. (No effect applied.)
MID : Select this when you want to reduce the dynamic range
a little.
MAX : Select this when you want to apply the compression
effect fully. (Useful at night.)
SPK 1
DIGITAL AUTO
L
C
R
S.WFR LFE
DIGITAL
LS
S
RS
CH-
* “0dB” is the initial setting. If you have already changed the
setting, “–10dB” will be shown.
18
EN10-22.RX-7020V[A]3
18
02.4.17, 5:16 PM
Sound Adjustments
Remote Control
Front Panel
Display
A/V CONTROL RECEIVER
RX-7022V AUDIO/VIDEO CONTROL RECEIVER
FM/AM TUNING
FM/AM PRESET
FM MODE
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
STANDBY
MEMORY
SPK 1 2
L
C
R
BASS BOOST
TUNED STEREO
AUTO MUTING SLEEP
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
VOLUME
S.WFR LFE
LS
S
BASS+/–
BASS
BOOST
MASTER VOLUME
RS
CH-
STANDBY/ON
INPUT
ANALOG/DIGITAL
SURROUND ON/OFF
BASS BOOST
ADJUST SETTING
DVD MULTI
DVD
VCR
CD
TAPE/CDR
PHONO
TV SOUND/DBS
INPUT ATT
CATV/DBS
VCR
DVD
DVD MULTI
CD
FM/AM
TV/DBS
VCR
TAPE/CDR
PHONO
−
BASS
SURROUND
ON/OFF
2
MODE
1
TREBLE
+
SLEEP
TREBLE+/–
INPUT
– CENTER +
2
3
MENU
SOUND
CONTROL
DOWN
UP
SPEAKERS ON/OFF
1
−
AUDIO
SURROUND ANALOG/DIGITAL
BASS BOOST EFFECT
SOURCE NAME
SURROUND MODE
+
TV
TEST
– REAR • L +
4
5
7/P
8
6
ENTER
SOUND
FM/AM
DIMMER
CATV/DBS
CONTROL
TV/VIDEO
9
– SUB WOOFER +
MUTING
SOURCE NAME
PHONES
– REAR • R +
10
0
+10
RETURN
FM MODE
100+
+
+
+
CH
TV VOL
VOLUME
−
−
SUBWOOFER +/–
−
+
TUNING
INPUT ATT BASS BOOST
REC
PAUSE
CONTROL
CONTROL
UP 5/DOWN ∞
Attenuating the Input Signal
Remote
NOT
FF/
−
ADJUST
Once each of following settings has been adjusted, this receiver
memorizes the adjustment for each source.
/REW
RM-SRX7022U REMOTE CONTROL
Adjusting the Front Speakers
Output Balance
Remote
NOT
If the sounds you hear from the front right and left speakers are
unequal, you can adjust the speakers output balance.
When the input level of the analog source is too high, the sounds
will be distorted. If this happens, you need to attenuate the input
signal level to prevent the sound distortion.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
1
1
Press and hold INPUT ATT
(INPUT ANALOG/DIGITAL) so
that the INPUT ATT indicator
lights up on the display.
INPUT
ANALOG / DIGITAL
INPUT ATT
Press ADJUST repeatedly until
“BALANCE” (with the current
setting)* appears on the display.
ADJUST SETTIN
SPK 1
ANALOG
DIGITAL AUTO
LINEAR PCM
SPK 1
L
C
R
INPUT ATT
S.WFR LFE
LS
S
L
C
R
S.WFR LFE
LS
S
RS
CH-
RS
CH-
• Each time you press and hold the button, the Input Attenuator
mode turns on (“INPUT ATT ON”) or off (“INPUT
NORMAL”).
Note:
When selecting “DVD MULTI” as the source, this effect does not work.
* “CNTR (Center)” is the initial setting. If you have already
changed the setting, another setting will be shown.
2
Press CONTROL UP 5/DOWN ∞
to adjust the balance.
• Pressing CONTROL UP 5 decreases the
left channel output from “CNTR” (Center)
to “L–21.”
• Pressing CONTROL DOWN ∞ decreases
the right channel output from “CNTR” (Center) to “R–21.”
19
EN10-22.RX-7020V[A]3
19
CONTROL
DOWN
UP
02.4.17, 5:16 PM
Adjusting the Tone
Adjusting the Subwoofer Output Level
You can adjust the bass and treble sounds as you like.
You can adjust the subwoofer output level if you have connected a
subwoofer and set the subwoofer information correctly—“YES.”
On the front panel:
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
1
Press ADJUST repeatedly until “BASS”
or “TREBLE” (with the current
setting)* appears on the display.
On the front panel:
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
ADJUST SETTING
1
Press ADJUST repeatedly until
“SUBWFR” (with the current setting)*
appears on the display.
ADJUST SETTING
SPK 1
DIGITAL AUTO
LINEAR PCM
L
C
R
S.WFR LFE
LS
S
SPK 1
RS
DIGITAL AUTO
LINEAR PCM
CH-
L
C
R
S.WFR LFE
LS
S
RS
CH-
* “0” is the initial setting. If you have already changed the
setting, another number (level) will be shown.
BASS
* “0” is the initial setting. If you have already changed the
setting, another number (level) will be shown.
: To adjust the bass.
2
TREBLE : To adjust the treble.
2
Press CONTROL UP 5/DOWN ∞ to
adjust the bass or treble sounds level
(–10 to +10).
From the remote control:
1
2
• Each time you press the button, the sound
level changes by ±2 steps.
SOUND
Press SOUND.
The 10 keys are activated for sound adjustments.
From the remote control:
Press BASS +/– or TREBLE +/– to
adjust the bass or treble sounds
level (–10 to +10).
CONTROL
DOWN
UP
CONTROL
DOWN
UP
• Each time you press the button, the sound
level changes by ±2 steps.
1
Press CONTROL UP 5/DOWN ∞ to
adjust the subwoofer output level
(–10 to +10).
−
BASS
+
Press SUBWOOFER +/– to adjust
the subwoofer output level
(–10 to +10).
– SUB WOOFER +
0
+10
FM MODE
100+
Note:
−
TREBLE
+
Subwoofer output level cannot be adjusted when using headphones.
Reinforcing the Bass
You can boost the bass level.
Press BASS BOOST on the front panel or on the
remote control to select the bass boost function.
BASS BOOST
On the front panel
BASS BOOST
From the remote control
• Each time you press the button, the bass boost function turns
on (“BASSBOOST ON”) and off (“BASSBOOST OFF”).
– Select “BASSBOOST ON” to activate the bass boost function.
The BASS BOOST indicator lights up on the display.
– Select “BASSBOOST OFF” to cancel it.
The indicator goes off.
Note:
This function affects the front speaker sounds only.
20
EN10-22.RX-7020V[A]3
20
02.4.17, 5:16 PM
Tuner Operations
Front Panel
Remote Control
FM/AM FM/AM
TUNING PRESET
5/∞
5/∞ FM MODE
A/V CONTROL RECEIVER
Display
RX-7022V AUDIO/VIDEO CONTROL RECEIVER
FM/AM TUNING
FM/AM PRESET
CATV/DBS
VCR
DVD
DVD MULTI
CD
FM/AM
TV/DBS
VCR
TAPE/CDR
PHONO
+
−
−
FM MODE
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
STANDBY
MEMORY
SPK 1 2
L
C
TUNED STEREO
BASS BOOST
AUTO MUTING SLEEP
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
R
VOLUME
S.WFR LFE
LS
S
BASS
SURROUND
MASTER VOLUME
RS
AUDIO
TREBLE
SURROUND ANALOG/DIGITAL
ON/OFF
MODE
BASS BOOST
EFFECT
SOUND
TEST
FM/AM
+
SLEEP
INPUT
– CENTER +
1
CH-
STANDBY/ON
TV
2
3
MENU
– REAR • L +
4
5
6
10 keys
ENTER
DIMMER
SURROUND ON/OFF
INPUT
ANALOG/DIGITAL
7/P
BASS BOOST
ADJUST SETTING
DVD
DVD MULTI
FM MODE
SOURCE NAME
CONTROL
DOWN
UP
SPEAKERS ON/OFF
1
2
CD
TAPE/CDR
PHONO
8
CATV/DBS
CONTROL
FM/AM
TV/VIDEO
9
– SUB WOOFER +
MUTING
TV SOUND/DBS
VCR
INPUT ATT
SURROUND MODE
– REAR • R +
10
0
+10
RETURN
FM MODE
100+
+
+
+
CH
TV VOL
VOLUME
−
−
−
SOURCE NAME
+
TUNING +/–
PHONES
TUNING
/REW
FF/
−
REC
PAUSE
CONTROL
FM/AM
MEMORY
Tuning in Stations Manually
1
Using Preset Tuning
Press FM/AM to select the band FM or AM.
The last received station of the selected band is tuned in.
To store the preset stations
On the front panel
From the remote control
• Each time you press the button, the band alternates between
FM and AM.
TUNED STEREO
SPK 1
L
C
Once a station is assigned to a channel number, the station can be
quickly tuned. You can preset up to 30 FM and 15 AM stations.
FM/AM
FM/AM
ANALOG
RM-SRX7022U REMOTE CONTROL
R
AUTO MUTING
VOLUME
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 2 again.
1
S.WFR LFE
LS
S
RS
CH-
Press FM/AM TUNING 5/∞ (TUNING +/– on
the remote control) repeatedly until you find the
frequency you want.
• Pressing FM/AM TUNING 5 (TUNING + on the remote
control) increases the frequency.
• Pressing FM/AM TUNING ∞ (TUNING – on the remote
control) decreases the frequency.
Tune in the station you want to preset
(see “Tuning in Stations Manually”).
If you want to store the FM reception mode for this station,
select the FM reception mode you want. See “Selecting the FM
Reception Mode” on page 22.
Ex.: When the FM band is selected
2
Remote
NOT
ANALOG
TUNED STEREO
SPK 1
L
C
AUTO MUTING
R
VOLUME
S.WFR LFE
LS
RS
S
CH-
2
Press MEMORY.
MEMORY
The CH- indicator lights up and the channel
number position starts flashing on the display for
about 5 seconds.
FM/AM TUNING
+
ANALOG
L
LS
−
On the front panel
From the remote control
Notes:
• When you press and hold FM/AM TUNING 5/ ∞ for a few seconds
in step 2, the frequency keeps changing until a station is tuned in.
• When a station of sufficient signal strength is tuned in, the TUNED
indicator lights up on the display.
• When an FM stereo program is received, the STEREO indicator
also lights up.
TUNED STEREO
SPK 1
C
21
VOLUME
RS
S
CH-
3
Press FM/AM PRESET 5/∞ to
select a channel number while the
channel number position is
flashing.
ANALOG
TUNED STEREO
SPK 1
L
C
R
S.WFR LFE
LS
S
RS
CH-
21
EN10-22.RX-7020V[A]3
AUTO MUTING
R
S.WFR LFE
TUNING
02.4.17, 5:16 PM
FM/AM PRESET
AUTO MUTING
VOLUME
4
Press MEMORY again while the
selected channel number is flashing
on the display.
Selecting the FM Reception Mode
MEMORY
When an FM stereo broadcast is hard to receive or noisy, you can
change the FM reception mode while receiving an FM broadcast.
• You can store the FM reception mode for each preset station. (See
page 21).
The selected channel number stops flashing.
The station is assigned to the selected channel number.
ANALOG
TUNED STEREO
SPK 1
L
C
AUTO MUTING
R
VOLUME
1
S.WFR LFE
LS
RS
S
CH-
5
Repeat steps 1 to 4 until you store all the stations
you want.
While listening to an FM station, press FM
MODE.
• Each time you press the button, the FM reception mode
alternates between “AUTO*” and “MONO.”
FM MODE
– SUB WOOFER +
0
To erase a stored preset station
FM MODE
Storing a new station on a used number erases the previously stored
one.
On the front panel
ANALOG
From the remote control
TUNED STEREO
SPK 1
L
C
AUTO MUTING
R
S.WFR LFE
To tune in a preset station
On the front panel:
1
LS
CH-
Press FM/AM to select the band
FM or AM.
FM/AM
ANALOG
TUNED STEREO
SPK 1
L
C
S
AUTO MUTING
R
VOLUME
LS
RS
AUTO
: Normally select this.
When a program is broadcasted in stereo, you will
hear stereo sound; when in monaural, you will
hear monaural sounds. This mode is also useful to
suppress static noise between stations. The AUTO
MUTING indicator lights up on the display.
MONO
: Select this to improve the reception (but stereo
effect will be lost).
In this mode, you will hear noise while tuning into
the stations. The AUTO MUTING indicator goes
off from the display. (The STEREO indicator also
goes off.)
FM/AM PRESET
• Pressing FM/AM PRESET 5 increases the
channel numbers.
• Pressing FM/AM PRESET ∞ decreases the
channel numbers.
S
* “AUTO” is the initial setting.
RS
Press FM/AM PRESET 5/∞
repeatedly until you find the channel
you want.
R
CH-
CH-
2
C
S.WFR LFE
S.WFR LFE
LS
TUNED
SPK 1
L
The last received station of the selected band is
tuned in.
• Each time you press the button, the band alternates between
FM and AM.
ANALOG
RS
S
From the remote control:
1
Press FM/AM to select the band
FM or AM.
FM/AM
The last received station of the selected band is
tuned in and the 10 keys now work for tuner operation.
• Each time you press the button, the band alternates between
FM and AM.
2
Press 10 keys to select a preset
channel number.
•
•
•
•
For channel number 5, press 5.
For channel number 15, press +10 then 5.
For channel number 20, press +10 then 10.
For channel number 30, press +10, +10,
then 10.
EFFECT
1
– CENTER +
2
3
MENU
TEST
4
– REAR • L +
5
6
ENTER
– REAR • R +
7/P
8
9
– SUB WOOFER +
10
0
+10
RETURN
FM MODE
100+
Note:
When you use 10 keys on the remote control, be sure that they are
activated for the tuner, not for the CD and others. (See page 34).
22
EN10-22.RX-7020V[A]3
22
02.4.17, 5:16 PM
Creating Realistic Sound Fields
You can use the following Surround modes to reproduce a realistic
sound field:
■ Dolby Surround
• Dolby Pro Logic II
• Dolby Digital
■ DTS Digital Surround
■ DAP modes
■ All Channel Stereo
■ Dolby Surround
Dolby Pro Logic II*
Dolby Digital*
Used to reproduce multichannel sound tracks of the software
).
encoded with Dolby Digital (
• To enjoy the software encoded with Dolby Digital, connect the
source component using the digital terminal on the rear of this
receiver. (See page 9.)
D I G I T A L
Dolby Digital 5.1 ch encoding method (so-called discrete
multichannel digital audio format) records and digitally compresses
the left front channel, right front channel, center channel, left rear
channel, right rear channel, and LFE channel signals.
Since each channel is completely independent from the other
channel signals to avoid interference, you can obtain much better
sound quality with much stereo and surround effects.
Dolby Pro Logic II has a newly developed multichannel playback
format to decode all 2 channel sources—stereo source and Dolby
Surround encoded source—into 5.1 channel.
Matrix-based encoding/decoding method for Dolby Pro Logic II
makes no limitation for the cutoff frequency of the rear treble and
enables stereo rear sound compared to conventional Dolby Pro
Logic.
Dolby Digital software can be roughly grouped into two categories
—multichannel (up to “5.1” ch) and 2 channel software. To enjoy
surround sounds while playing Dolby Digital 2 ch software, you can
use Dolby Pro Logic II.
Dolby Pro Logic II enables to reproduce spacious sound from
original sound without adding any new sounds and tonal colorations.
Dolby Pro Logic II has two modes—Movie mode and Music mode:
■ DTS Digital Surround**
Pro Logic II Movie (PL II MOVIE)—suitable for reproduction of
DOLBY SURROUND .
Dolby Surround encoded sources bearing the mark
You can enjoy soundfield very close to the one created with discrete
5.1 channel sounds.
Pro Logic II Music (PL II MUSIC)—suitable for reproduction of
any 2 channel stereo music sources. You can enjoy wide and deep
sound by using this mode. For this mode, Panorama control can be
selected, which gives “wraparound” sound effect with side-wall
image.
• When Dolby Pro Logic II is activated,
indicator lights up on the display.
PRO LOGIC II
Note:
Used to reproduce multichannel sound tracks of the software
encoded with DTS Digital Surround (
).
• To enjoy the software encoded with DTS Digital Surround,
connect the source component using the digital terminal on the
rear of this receiver. (See page 9.)
DTS Digital Surround is another discrete multichannel digital
audio format available on CD, LD, and DVD software.
Compared to Dolby Digital, audio compression ratio is relatively
low. This fact allows DTS Digital Surround format to add breadth
and depth to the reproduced sounds. As a result, DTS Digital
Surround features natural, solid and clear sound.
Typical Multichannel (5.1 ch) reproduction
Center
speaker
Subwoofer Right front
speaker
Left front
speaker
STANDBY
STANDBY ON
DOLBY
D I G I T A L
RX-7020V AUDIO/VIDEO CONTROL RECEIVER
FM/AM TUNING
FM/AM PRESET
FM MODE
STANDBY
MASTER VOLUME
COMPULINK
Remote
MEMORY
D I G I T A L
SURROUND
SURROUND ON/OFF
INPUT
ANALOG/DIGITAL
BASS BOOST
ADJUST SETTING
DVD MULTI
DVD
VCR
TAPE/CDR
PHONO
TV SOUND/DBS
INPUT ATT
SOURCE NAME
SURROUND MODE
CONTROL
DOWN
UP
SPEAKERS ON/OFF
1
2
CD
FM/AM
SOURCE NAME
PHONES
Left rear
speaker
* Manufactured under license from Dolby Laboratories. “Dolby,”
“Pro Logic,” and the double-D symbol are trademarks of Dolby
Laboratories. Confidential unpublished works. ©1992–1997 Dolby
Laboratories. All rights reserved.
** Manufactured underlicense from Digital Theater Systems, Inc. US
PAT. No. 5,451,942 and other world-wide patents issued and
pending. “DTS” and “DTS Digital Surround” are trademarks of
Digital Theater Systems, Inc. Copyright 1996 Digital Theater
Systems, Inc. All rights reserved.
23
EN23-29.RX-7020V[A]3
23
Right rear
speaker
02.4.17, 5:16 PM
■ DAP (Digital Acoustic Processor) modes
■ All Channel Stereo
DAP modes have been designed to create important acoustic
surround elements.
This mode can reproduce a larger stereo sound field using all the
connected (and activated) speakers.
The sound heard in a live club, dance club, hall or pavilion consists
of direct sound and indirect sound—early reflections and reflections
from behind. Direct sounds reach the listener directly without any
reflection. On the other hand, indirect sounds are delayed by the
distances of the ceiling and walls (see the diagram below).
These indirect sounds are important elements of the acoustic
surround effects. The DAP mode can reproduce a realistic sound
field by adding these indirect sounds.
All Channel Stereo can be used when the front and rear
speakers are connected to this receiver without respect to the
center speaker connection.
If the center speaker is connected and activated, the same phase of
the front left and right signals are output through the center speaker.
DAP modes can be used when the front and rear speakers are
connected to this receiver (without respect to the center speaker
connection: no sound comes out of the center speaker even if it is
connected).
All Channel Stereo can be used while reproducing 2 channel stereo
software, either analog or digital except Dolby Digital and DTS
Digital Surround.
• When All Channel Stereo is selected, the DSP indicator lights up
on the display.
All Channel Stereo reproduction
The following DAP modes are provided with this receiver:
LIVE CLUB
: Gives the feeling of a live music club with a low
ceiling.
DANCE CLUB : Gives a throbbing bass beat.
HALL
: Gives clear vocal and the feeling of a concert
hall.
PAVILION
: Gives the spacious feeling of a pavilion with a
high ceiling.
These DAP modes can be used to add the acoustic surround effects
while reproducing 2 channel stereo software—either analog or
digital except Dolby Digital and DTS Digital Surround—and can
give you a real “being there” feeling.
• When one of the DAP modes is selected, the DSP indicator lights
up on the display.
Sound reproduced from All Channel Stereo
DVD MULTI Playback Mode
Creating sound field
This receiver provides the DVD MULTI playback mode for
reproducing the analog discrete 5.1 channel output mode of the
DVD player or other equipment.
You can adjust speaker output levels while playing back a video
software such as a DVD using the analog discrete 5.1 channel
output mode.
• For connecting analog discrete output jacks, see page 8.
• For details on the DVD MULTI playback mode, see page 30.
Reflections from behind
Early reflections
Note:
When you select “DVD MULTI” as the source to play, Surround mode
is canceled, and the SURROUND ON/OFF and SURROUND MODE
buttons do not work.
Direct sounds
䡬: Possible / ⳯: Impossible
Available Surround modes for each input signal
Mode SURROUND
Signals
OFF (stereo)
DOLBY
DIGITAL
DTS
SURROUND
PLII
MOVIE
PLII
MUSIC
LIVE
CLUB
DANCE
CLUB
HALL
PAVILION
ALL CH
STEREO
Dolby Digital
(Multichannel)
䡬
䡬
⳯
⳯
⳯
⳯
⳯
⳯
⳯
⳯
Dolby Digital
(2 channel)
䡬
⳯
⳯
䡬
䡬
⳯
⳯
⳯
⳯
⳯
DTS Digital
Surround
(Multichannel)
䡬
⳯
䡬
⳯
⳯
⳯
⳯
⳯
⳯
⳯
DTS Digital
Surround
(2 channel)
䡬
⳯
⳯
䡬
䡬
⳯
⳯
⳯
⳯
⳯
Linear PCM
䡬
⳯
⳯
䡬
䡬
䡬
䡬
䡬
䡬
䡬
Analog
䡬
⳯
⳯
䡬
䡬
䡬
䡬
䡬
䡬
䡬
24
EN23-29.RX-7020V[A]3
24
02.4.17, 5:16 PM
Creating Realistic Sound Fields
About Relations between Speaker Layouts and Surround Modes
Available Surround modes will vary depending on how many speakers are used with this receiver.
Make sure that you have set the speaker information correctly (see pages 16 to 18).
• If only front speakers are connected, you cannot use Surround modes.
• If rear speakers are not connected, you cannot use DAP modes and All Channel Stereo.
Speaker Layouts
Available Surround modes
When the center and rear speakers
are connected (5 channels):
Turning on or off the Surround modes
Each time you press SURROUND ON/OFF, Surround modes turn on or off.
Front
speaker
TV
Front
speaker
L
DIGITAL AUTO
LINEAR PCM
C
AUTO MUTING
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
R
S.WFR LFE
S
RS
ON/OFF
(Remote)
Rear
speaker
SURROUND ON/OFF
LS
Center speaker
TUNED STEREO
SPK 1
SURROUND
Rear
speaker
(Front panel)
Last selected
Surround mode
SURROUND OFF
Ex.: “PL II MUSIC” has been selected.
Selecting the Surround modes
Each time you press SURROUND MODE, Surround modes change as follows:
TUNED STEREO
SPK 1
L
DIGITAL AUTO
LINEAR PCM
SURROUND
When the rear speakers are connected
(4 channels):
Front
speaker
TV
Front
speaker
C
AUTO MUTING
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
R
VOLUME
S.WFR LFE
SURROUND MODE
LS
S
RS
MODE
(Remote)
(Front panel)
PL II MOVIE
LIVE CLUB
HALL
ALL CH STEREO
PL II MUSIC
DANCE CLUB
PAVILION
(Back to the beginning)
Note:
Rear
speaker
Rear
speaker
When the center speaker is connected
(3 channels):
When the digital multichannel software such as Dolby Digital or DTS Digital
Surround is played back, the appropriate multichannel Surround mode is activated
(“DOLBY DIGITAL” or “DTS SURROUND”) by pressing SURROUND ON/OFF (with
the digital input mode selected).
• For Dolby Digital 2 ch software, you need to select “PLII MUSIC” or “PLII MOVIE”
by pressing SURROUND MODE.
• For more details, see the table on page 24.
Turning on or off the Surround modes
Each time you press SURROUND ON/OFF, the Surround modes turn on or off.
TUNED STEREO
SPK 1
DIGITAL AUTO
LINEAR PCM
Front
speaker
TV
Center speaker
Front
speaker
SURROUND
L
SURROUND ON/OFF
C
R
AUTO MUTING
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
S.WFR LFE
LS
S
RS
ON/OFF
(Remote)
(Front panel)
PL II MOVIE
or
PL II MUSIC
SURROUND OFF
Ex.: “PL II MUSIC” has been selected.
Selecting the Surround modes
Each time you press SURROUND MODE, Surround modes change as follows:
SURROUND
SURROUND MODE
L
(Front panel)
C
R
AUTO MUTING
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
S.WFR LFE
LS
(Remote)
TUNED STEREO
SPK 1
DIGITAL AUTO
LINEAR PCM
MODE
S
RS
PL II MOVIE
PL II MUSIC
Note:
When the digital multichannel software such as Dolby Digital or DTS Digital
Surround is played back, the appropriate multichannel Surround mode is activated
(“DOLBY DIGITAL” or “DTS SURROUND”) by pressing SURROUND ON/OFF (with
the digital input mode selected).
• For Dolby Digital 2 ch software, you need to select “PLII MUSIC” or “PLII MOVIE”
by pressing SURROUND MODE.
• For more details, see the table on page 24.
25
EN23-29.RX-7020V[A]3
25
02.4.17, 5:16 PM
Before you start, remember...
• Make sure that you have set the speaker information correctly (see pages 16 to 18).
• You cannot adjust the center speaker output level when you have set “CNTR SP” to “NONE.”
• You cannot adjust the rear speaker output levels when you have set “REAR SP” to “NONE.”
• Remember not to change the speaker setting while using any Surround modes; otherwise, it may be canceled when you deactivate the
speakers required for the Surround mode.
Front Panel
Display
RX-7022V AUDIO/VIDEO CONTROL RECEIVER
FM/AM TUNING
FM/AM PRESET
FM MODE
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
STANDBY
MEMORY
SPK 1 2
L
C
R
BASS BOOST
TUNED STEREO
AUTO MUTING SLEEP
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
VOLUME
S.WFR LFE
LS
S
MASTER VOLUME
RS
CH-
STANDBY/ON
INPUT
ANALOG/DIGITAL
SURROUND ON/OFF
BASS BOOST
ADJUST SETTING
DVD MULTI
DVD
VCR
TV SOUND/DBS
INPUT ATT
SOURCE NAME
SURROUND MODE
CONTROL
DOWN
UP
SPEAKERS ON/OFF
1
2
CD
TAPE/CDR
PHONO
FM/AM
SOURCE NAME
PHONES
SURROUND SURROUND
ON/OFF
MODE
ADJUST
CONTROL
UP 5/DOWN ∞
Using Dolby Pro Logic II, Dolby Digital
and DTS Digital Surround
Remote Control
Once you have adjusted the Surround modes, the adjustment is
memorized for each source.
• When playing back digital multichannel software (Dolby Digital
5.1 ch or DTS Digital Surround), the SURROUND MODE button
does not work.
A/V CONTROL RECEIVER
From the remote control:
CATV/DBS
VCR
TV
AUDIO
DVD
DVD MULTI
CD
FM/AM
VCR
TAPE/CDR
TV/DBS
SURROUND
ON/OFF
EFFECT
−
BASS
+
ON/OFF
MODE
BASS BOOST EFFECT
1
SURROUND
MODE
INPUT
– CENTER +
2
CENTER +/–
3
MENU
TEST
4
TEST
+
SURROUND SURROUND ANALOG/DIGITAL SLEEP
SOUND
SOUND
−
PHONO
TREBLE
– REAR • L +
5
6
REAR•L +/–
It will be convenient for you to use the remote control for
adjustments, since you can make adjustments from your listening
point, by using the test signal.
• For selecting Panorama mode for Pro Logic II Music, use the
button on the front panel.
1
ENTER
DIMMER
– REAR • R +
7/P
CATV/DBS
CONTROL
TV/VIDEO
8
9
– SUB WOOFER +
MUTING
10
0
+10
RETURN
FM MODE
100+
+
+
+
CH
TV VOL
VOLUME
−
−
−
+
TUNING
/REW
FF/
−
REC
PAUSE
CONTROL
RM-SRX7022U REMOTE CONTROL
REAR•R +/–
Setting the analog or digital input mode for the
source you like to listen and start playing.
When playing back software encoded with Dolby Digital and DTS
Digital Surround, select the digital input mode (see page 15).
2
Press SURROUND ON/OFF to
activate Surround mode.
SURROUND
ON/OFF
Each time you press the button, Surround mode
turns on and off alternately.
• If you are playing back software encoded with Dolby Digital
multichannel, “DOLBY DIGITAL” is selected.
• If you are playing back software encoded with DTS Digital
Surround, “DTS SURROUND” is selected.
• If you are playing back any software other
SURROUND
MODE
than above, you can select “PL II MUSIC” or
“PL II MOVIE” according to the source by
pressing SURROUND MODE. ( PRO
LOGIC II indicator lights up on the display.)
If you like to adjust sound, go to step 3.
26
EN23-29.RX-7020V[A]3
26
02.4.17, 5:16 PM
Creating Realistic Sound Fields
3
Press SOUND.
On the front panel:
SOUND
The 10 keys are activated for sound adjustments.
4
Press TEST to check if you can hear
the sounds through all the speakers at
the equal level.
You can also use the buttons on the front panel to adjust the
Surround modes. However, no test tone is available when using the
buttons on the front panel. So make adjustments while listening to
the sound of the source played back.
TEST
4
1
“TEST TONE L” starts flashing on the display and a test tone
comes out of the speakers in the following order:
TEST TONE L
TEST TONE C
TEST TONE R
(Left front speaker)
(Center speaker)
(Right front speaker)
TEST TONE LS
TEST TONE RS
(Left rear speaker)
(Right rear speaker)
When playing back software encoded with Dolby Digital and DTS
Digital Surround, select the digital input mode (see page 15).
2
• You can adjust the speaker output levels without outputting the
test tone.
• No test tone comes out of the center speaker when “CNTR SP”
is set to “NONE.”
• No test tone comes out of the rear speakers when “REAR SP”
is set to “NONE.”
Adjust the speaker output levels (–10 to +10).
Adjust the center speaker and rear speakers levels comparing to
the sound from the front speakers.
• To adjust the center speaker level, press
CENTER +/–.
• To adjust the left rear speaker level, press
REAR•L +/–.
– CENTER +
2
3
MENU
– REAR • L +
5
6
ENTER
Press SURROUND ON/OFF to
activate Surround mode.
SURROUND ON/OFF
Each time you press the button, Surround
mode turns on and off alternately.
• If you are playing back software encoded with Dolby Digital
multichannel, “DOLBY DIGITAL” is selected.
• If you are playing back software encoded with DTS Digital
Surround, “DTS SURROUND” is selected.
• If you are playing back any software other
SURROUND MODE
than above, you can select “PL II MUSIC”
or “PL II MOVIE” according to the source
by pressing SURROUND MODE. ( PRO
LOGIC II indicator lights up on the display.)
Notes:
5
Setting the analog or digital input mode for the
source you like to hear and start playing.
If you like to adjust sound, go to step 3.
3
Adjust the speaker output levels.
1) Press ADJUST repeatedly until one
of the following indications (with the
current setting)* appears on the
display.
ADJUST SETTING
ENTER
• To adjust the right rear speaker level, press
REAR•R +/–.
6
Press TEST again to stop the test
tone.
– REAR • R +
8
9
L
C
R
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
AUTO MUTING
VOLUME
S.WFR LFE
LS
TEST
TUNED STEREO
SPK 1
DIGITAL AUTO
LINEAR PCM
S
RS
* “0” is the initial setting. If you have already changed the
setting, another number (level) will be shown.
4
CENTER : To adjust the center speaker output level
(–10 to +10).
REAR L : To adjust the left rear speaker output level
(–10 to +10).
REAR R : To adjust the right rear speaker output level
(–10 to +10).
2) Press CONTROL UP 5/
DOWN ∞ to adjust the selected
speaker output levels.
CONTROL
DOWN
UP
3) Repeat steps 1) and 2) to adjust the other
speaker levels.
27
EN23-29.RX-7020V[A]3
27
02.4.17, 5:16 PM
When you select “PL II MUSIC,” you can go to the
following adjustment.
Remote
NOT
4
Turn Panorama control on or off.
1) Press ADJUST repeatedly until
“PANORAMA” (with the current
setting)* appears on the display.
TUNED STEREO
SPK 1
DIGITAL AUTO
LINEAR PCM
L
C
R
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
ADJUST SETTING
Using DAP Modes and All Channel Stereo
Once you have adjusted the DAP modes and All Channel Stereo, the
adjustment is memorized for each source.
• You cannot use the DAP modes and All Channel Stereo if no rear
speakers are connected.
• You cannot adjust the effect level for “ALL CH STEREO.”
From the remote control:
AUTO MUTING
VOLUME
It will be convenient for you to use the remote control for
adjustments, since you can make adjustments from your listening
point.
S.WFR LFE
LS
S
RS
* “OFF” is the initial setting. If you have already changed
the setting, “ON” will be shown.
2) Press CONTROL UP 5/
DOWN ∞ to turn on or off
Panorama control.
1
Start playing 2 channel software—either analog
or Linear PCM—and select the source.
2
Press SURROUND ON/OFF to activate
Surround mode.
CONTROL
DOWN
UP
• Each time you press the button, “ON”
and “OFF” change alternately.
ON
: Select this when you like to enjoy
“wraparound” sound effect with side-wall
image.
OFF
: Select this when you like to enjoy
originally recorded sounds.
SURROUND
ON/OFF
When the Surround mode turns on, the last selected
Surround mode will be activated.
• Each time you press the button, Surround mode turns on and
off alternately.
3
Press SURROUND MODE repeatedly
until one of the DAP modes—“LIVE
CLUB,” “DANCE CLUB,” “HALL”
and “PAVILION”—or “ALL CH
STEREO” appears on the display.
SURROUND
MODE
The DSP indicator also lights up on the display.
If you like to adjust sound, go to step 4.
4
To cancel Surround mode
Press SURROUND ON/OFF again so that “SURROUND OFF”
appears on the display.
• If Surround mode is canceled while playing back multichannel
digital software, all channel signals are mixed and output through
the front speakers (and subwoofer if you have connected a
subwoofer and set the subwoofer setting correctly—“YES”).
Press SOUND.
SOUND
The 10 keys are activated for sound adjustments.
5
Adjust the speaker output levels
(–10 to +10).
• To adjust the left rear speaker level, press
REAR•L +/–.
5
• To adjust the right rear speaker level, press
REAR•R +/–.
8
– REAR • L +
6
ENTER
ENTER
For “ALL CH STEREO” only:
• To adjust the center speaker level, press
CENTER +/–.
6
– REAR • R +
9
– CENTER +
2
3
MENU
For DAP modes only:
Press EFFECT to select the effect
level (1 to 5) you want.
EFFECT
1
• Each time you press the button, the effect
level changes as follows:
EFFECT 1
EFFECT 2
EFFECT 5
EFFECT 3
EFFECT 4
As the number increases, selected mode becomes stronger
(normally set it to “EFFECT 3”).
28
EN23-29.RX-7020V[A]3
28
02.4.17, 5:16 PM
Creating Realistic Sound Fields
5
On the front panel:
1
Start playing 2 channel software—either analog
or Linear PCM—and select the source.
2
Press SURROUND ON/OFF to
activate Surround mode.
SURROUND ON/OFF
When Surround mode turns on, the last selected
Surround mode will be activated.
• Each time you press the button, Surround mode
turns on and off alternately.
3
For DAP modes only: Adjust the effect level.
1) Press ADJUST repeatedly until
“EFFECT” (with the current
setting)* appears on the display.
ADJUST SETTING
* “EFFECT 3” is the initial setting. If you have already
changed the setting, another setting will be shown.
2) Press CONTROL UP 5/
DOWN ∞ to select the effect
level (1 to 5) you want.
Press SURROUND MODE repeatedly SURROUND MODE
until one of the DAP modes—“LIVE
CLUB,” “DANCE CLUB,” “HALL”
and “PAVILION”—or “ALL CH STEREO”
appears on the display.
The DSP indicator also lights up on the display.
CONTROL
DOWN
UP
• Each time you press the button, the effect
level changes as follows:
EFFECT 1
EFFECT 5
EFFECT 2
EFFECT 3
EFFECT 4
As the number increases, selected mode becomes stronger
(normally set it to “EFFECT 3”).
If you like to adjust sound, go to step 4.
4
To cancel DAP modes and All Channel Stereo
Adjust the speaker output levels.
1) Press ADJUST repeatedly until one
of the following indications (with
the current setting)* appears on the
display.
ADJUST SETTING
Press SURROUND ON/OFF again so that “SURROUND OFF”
appears on the display. The DSP indicator goes off.
REAR L : To adjust the left rear speaker output level
(–10 to +10).
REAR R : To adjust the right rear speaker output level
(–10 to +10).
CENTER : For “ALL CH STEREO” only—to adjust the
center speaker output level
(–10 to +10).
* “0” is the initial setting. If you have already changed the
setting, another number (level) will be shown.
2) Press CONTROL UP 5/
DOWN ∞ to adjust the selected
speaker output levels.
CONTROL
DOWN
UP
3) Repeat steps 1) and 2) to adjust the other
speaker levels.
29
EN23-29.RX-7020V[A]3
29
02.4.17, 5:16 PM
Using DVD MULTI Playback Mode
This receiver provides the DVD MULTI playback mode for
reproducing the analog discrete output mode of the DVD player.
Before playing back a DVD, refer also to the manual supplied with
the DVD player.
From the remote control:
1
When you select “DVD MULTI” as the source to play, Surround
mode is canceled, and the SURROUND ON/OFF and
SURROUND MODE buttons do not work.
2
If you need to make any adjustments, go to the
following steps.
3
On the front panel:
4
Press DVD MULTI.
Press SOUND.
SOUND
The 10 keys are activated for adjusting the sound.
Adjust the speaker output levels.
DVD MULTI
Notes:
• When you select “DVD MULTI” as the source to play, the
Surround mode is canceled, and the SURROUND ON/OFF and
SURROUND MODE buttons do not work.
• If you select the source to DVD MULTI while using both the
speakers connected to the FRONT SPEAKERS 1 and 2
terminals, the speakers connected to the FRONT SPEAKERS
2 terminals are deactivated.
• When selecting “DVD MULTI” as the source, you can only
select either the speakers connected to the FRONT
SPEAKERS 1 or 2 terminals.
2
Select the analog discrete output mode on the
DVD player, and start playing a DVD.
• Refer also to the manual supplied with the DVD player.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
1
DVD MULTI
Note:
Activating DVD MULTI Playback Mode
You can adjust the DVD MULTI playback mode while playing back
a DVD using the analog discrete output mode on the DVD player.
Once you have made adjustments, the receiver memorizes the
adjustments until you change them.
You also need to set the DVD player to the analog discrete output
mode.
Press DVD MULTI.
• To adjust the center speaker level, press
CENTER +/– (–10 to +10).
2
• To adjust the left rear speaker level, press
REAR•L +/– (–10 to +10).
5
• To adjust the right rear speaker level, press
REAR•R +/– (–10 to +10).
8
– CENTER +
3
MENU
– REAR • L +
6
ENTER
ENTER
– REAR • R +
9
Select the analog discrete output mode on the
DVD player, and start playing a DVD.
• Refer also to the manual supplied with the DVD player.
If you need to make any adjustments, go to the
following steps.
3
Adjust the speaker output levels.
1) Press ADJUST repeatedly until one
of the following indications appears
on the display.
ADJUST SETTING
CENTER :To adjust the center speaker output level
(–10 to +10).
REAR L : To adjust the left rear speaker output level
(–10 to +10).
REAR R : To adjust the right rear speaker output level
(–10 to +10).
2) Press CONTROL UP 5/DOWN ∞
to adjust the selected speaker
output levels.
CONTROL
DOWN
UP
3) Repeat steps 1) and 2) to adjust the other
speaker output levels.
30
EN30-42.RX-7020V[A]3
30
02.4.17, 5:16 PM
COMPU LINK Remote Control System
The COMPU LINK remote control system allows you to operate
JVC’s audio components through the remote sensor on the receiver.
To use this remote control system, you need to connect JVC’s audio
components through the COMPU LINK-4 (SYNCHRO) jacks (see
below) in addition to the connections using cables with RCA pin
plugs (see pages 6 and 7).
• Make sure that the AC power cords of these components are
unplugged before connection. Plug the AC power cords only after
all connections are completed.
Automatic Power On/Off (Standby): only possible with the
COMPU LINK-3 and COMPU LINK-4
Both the CD player and cassette deck (or CD recorder) turn on and
off (standby) along with the receiver.
When you turn on the receiver, the CD player or cassette deck (or
CD recorder) will turn on automatically, depending on which
component has been previously selected.
When you turn off the receiver, both the CD player and cassette
deck (or CD recorder) will turn off (standby).
Synchronized Recording
CD player
Cassette deck
or
CD recorder
COMPU LINK-4
(SYNCHRO)
Synchronized recording means the cassette deck starts recording as
soon as a CD begins playing.
To use synchronized recording, follow these steps:
1 Put a tape in the cassette deck and a disc in the
CD player.
2 Press the record (¶) button and the pause (8)
button on the cassette deck at the same time.
This puts the cassette deck into recording pause.
If you do not press the record (¶) button and pause (8) button at
the same time, the synchronized recording feature will not
operate.
Turntable
3 Press the play (3) button on the CD player.
The source changes on the receiver, and as soon as play starts,
the cassette deck starts recording. When the play ends, the
cassette deck enters recording pause, and stops about 4 seconds
later.
Notes:
• There are four versions of COMPU LINK remote control system.
This receiver is equipped with the fourth version—COMPU LINK-4.
This version is added systematic operations with the CD recorder to
the previous version—COMPU LINK-3.
• If your audio component has two COMPU LINK jacks, you can use
either one. If it has only one COMPU LINK jack, connect it so that it
is the last item in the series of components.
• To operate the cassette deck or CD recorder using the COMPU
LINK remote control system, set the source name correctly.
(See page 11.)
• Refer also to the manuals supplied with your audio components.
Notes:
• During synchronized recording, the selected source cannot be
changed.
• If the power of any component is shut off during synchronized
recording, the COMPU LINK remote control system may not
operate properly. In this case, you must start again from the
beginning.
This remote control system allows you to use four functions listed
below.
Remote Control through the Remote Sensor on the Receiver
You can control the connected audio components through the remote
sensor on the receiver using this remote control. Aim the remote
control directly at the remote sensor on the receiver. For details, see
pages 34 and 35.
Automatic Source Selection
3) button on a connected component or
When you press the play (3
on its own remote control, the receiver automatically turns on and
changes the source to the component. On the other hand, if you
select a new source on the receiver or on the remote control, the
selected component begins playing immediately.
In both cases, the previously selected source continues playing
without sound for a few seconds.
31
EN30-42.RX-7020V[A]3
31
02.4.17, 5:16 PM
AV COMPU LINK Remote Control System
The AV COMPU LINK remote control system allows you to operate JVC’s video components (TV, VCR, and DVD player) through the
receiver.
This receiver is equipped with the AV COMPU LINK-III, which added a function to operate JVC’s video components through the video
components terminals. To use this remote control system, you need to connect the video components you want to operate, following the
diagrams below and the procedure on the next page.
CONNECTIONS 1: AV COMPU LINK Connection
VCR
TV
DVD player
VHS
DVD
AV
COMPU LINK – III
Note:
AV
COMPU LINK
AV
COMPU LINK
You can only connect to the TV
with the AV COMPU LINK EX or
AV COMPU LINK III terminal.
The TV with AV COMPU LINK
RECEIVER/AMP terminal will
not be used.
AV
COMPU LINK EX
AV
COMPU LINK III
IMPORTANT:
The AV COMPU LINK remote control system cannot control the DBS tuner
connected to the TV SOUND/DBS and DBS COMPONENT VIDEO terminals.
Notes:
• When connecting the receiver and a TV with the AV COMPU LINK EX terminal by using a component video cable, you cannot use Automatic
Selection of TV’s Input Mode (see page 33).
• When connecting only the VCR or DVD player to this receiver, connect it directly to the receiver using cables with the monaural mini-plugs.
• Make sure that the remote control code of the VCR connected to the VCR jacks is set to code “A.”
• Refer also to the manuals supplied with your video components.
CONNECTIONS 2: Video Cable Connections
This receiver is equipped with three types of video terminals — S-video, composite video, and component video — and the signals coming
into this receiver through one type of video terminal can output only through the same type of the terminal. So you need to connect the VCR
and/or DVD player to the TV using one of the following three ways:
CASE 1
When connecting the source equipment to the receiver using the S-video terminals, connect also this
receiver to the TV’s Video Input 1 terminal using S-video cables.
Source
Equipment
S-video cable
RX-7022VSL
S-video cable
TV
To Video Input 1
Note:
If you connect the DVD player and the DBS tuner to this receiver using the S-video terminals, change the video input
terminal setting to “S/C” (see page 16).
CASE 2
When connecting the source equipment to the receiver using the composite video terminals, connect also
this receiver to the TV’s Video Input 2 terminal (composite video input) using composite video cables.
Source
Equipment
Composite
video cable
RX-7022VSL
Composite
video cable
TV
To Video Input 2
(Composite)
If you connect the DVD player and the DBS tuner to this receiver using the composite video terminals, change the video
input terminal setting to “S/C” (see page 16).
Note:
CASE 3
When connecting the source equipment to the receiver using the component video terminals, connect also
this receiver to the TV’s Video Input 2 terminals (component video input) using component video cables.
Source
Equipment
Component
video cable
RX-7022VSL
Component
video cable
TV
To Video Input 2
(Component)
If you connect the DVD player and the DBS tuner to this receiver using the component video terminals, change the
video input terminal setting to “COMPONENT” (see page 16).
Note:
32
EN30-42.RX-7020V[A]3
32
02.4.17, 5:16 PM
AV COMPU LINK Remote Control System
1. If you have already plugged your VCR, DVD
player, TV and this receiver into the AC outlets,
unplug their AC power cords first.
2. Connect your VCR, DVD player, TV and this
receiver as follows, using the cables with the
monaural mini-plugs (not supplied).
• See “CONNECTIONS 1” on the previous page.
3. Connect the audio input/output jacks on VCR,
DVD player, TV and this receiver, using the
cables with RCA pin plugs.
• See pages 7 and 8.
One-Touch DVD Play
Simply by starting playback on the DVD player, you can enjoy the
DVD playback without setting other switches manually.
• When the DVD player is connected through the analog input jacks
on this receiver (and analog input is selected), the receiver
automatically turns on and changes the source to “DVD” or
“DVD MULTI.”
• When the DVD player is connected through the digital input
terminal on this receiver (and digital input is selected), the
receiver automatically turns on and changes the source to “DVD
DIGITAL.”
The TV automatically turns on and changes the input mode to the
appropriate position so that you can view the playback picture.
Automatic Selection of TV’s Input Mode
4. Connect the video input/output jacks on VCR,
DVD player, TV and this receiver, using the
cables with RCA pin plugs, with S-video plug or
with component video plugs.
• See “CONNECTIONS 2” on the previous page.
5. Plug the AC power cords of the components into
the AC outlets.
6. When turning on the TV for the first time after
the AV COMPU LINK connection, turn the TV
volume to the minimum using the TV volume
control on the TV.
7. Turn on the other connected components first,
then turn on this receiver.
• When turning on the VCR, use the remote control supplied
with this receiver (press VCR
).
The AV COMPU LINK remote control system allows you to use the
five basic functions listed below.
Remote Control of the TV, DVD player, and VCR Using This
Remote Control
See page 36 for details.
• Aim the remote control directly at the remote sensor on each
target component.
• When you select “TV” as the source to play on the receiver, the
TV automatically changes the input mode to the TV tuner so that
you can watch TV.
• When you select “DVD,” “DVD MULTI,” “VCR” or “DBS” as
the source to play on the receiver, the TV automatically changes
the input mode to the appropriate position (either Video Input 1 or
Video Input 2) so that you can view the playback picture.
Note:
When connecting a TV with the AV COMPU LINK EX terminal to this
receiver, you cannot use a component video cable (as case 3 on page
32). Connect the TV using a S-video or composite video cable
(as cases 1 and 2).
Automatic Power On/Off
The TV, VCR, and DVD player turn on and off along with the
receiver.
When you turn on the receiver;
• If the previously selected source is “VCR,” the TV and VCR will
turn on automatically.
• If the previously selected source is “TV SOUND” or “DBS,” only
the TV will turn on automatically.
• If the previously selected source is “DVD” or “DVD MULTI,” the
TV and DVD player will turn on automatically.
When you turn off the receiver, the TV, VCR and DVD player will
turn off.
Note:
If you turn off the receiver while recording on the VCR, the VCR will
not turn off, but continue recording.
One-Touch Video Play
Simply by inserting a video cassette without its safety tab into the
VCR, you can enjoy the video playback without setting other
switches manually. The receiver automatically turns on and changes
the source to “VCR.”
The TV automatically turns on and changes the input mode to the
appropriate position so that you can view the playback picture.
When you insert a video cassette with its safety tab, press the play
3) button on the VCR or on the remote control. So, you can get the
(3
same result.
33
EN30-42.RX-7020V[A]3
33
02.4.17, 5:16 PM
Operating JVC’s Audio/Video Components
You can use the remote control to operate other JVC’s
components.
Operating Audio Components
A/V CONTROL RECEIVER
CATV/DBS
VCR
TV
AUDIO
DVD
DVD MULTI
CD
FM/AM
VCR
TAPE/CDR
TV/DBS
−
BASS
SURROUND
ON/OFF
+
−
BASS BOOST EFFECT
1
+
SLEEP
TEST
4
Sound Adjustment
You can always use the following buttons:
INPUT
– CENTER +
2
3
MENU
SOUND
To operate JVC’s audio components using this remote control:
• You need to connect JVC’s audio components through the COMPU
LINK-4 (SYNCHRO) jacks (see page 31) in addition to the
connections using cables with RCA pin plugs (see pages 6 and 7).
• Aim the remote control directly at the remote sensor on the receiver.
• If you use the buttons on the front panel, the remote control will not
operate that source. To operate a source with the remote control,
the source must be selected using source selecting buttons on the
remote control.
• To operate the cassette deck or CD recorder using the COMPU
LINK remote control system, set the source name correctly. (See
page 11.)
• Refer also to the manuals supplied with your audio components.
PHONO
TREBLE
SURROUND ANALOG/DIGITAL
MODE
IMPORTANT:
– REAR • L +
5
6
SURROUND ON/OFF : Turn on or off the Surround modes.
SURROUND MODE
: Select the Surround modes.
ENTER
DIMMER
– REAR • R +
7/P
CATV/DBS
CONTROL
TV/VIDEO
8
9
– SUB WOOFER +
MUTING
10
0
+10
RETURN
FM MODE
100+
+
+
+
CH
TV VOL
VOLUME
−
−
−
+
TUNING
/REW
FF/
−
REC
PAUSE
After pressing SOUND, you can use the following buttons for sound
adjustment:
SUBWOOFER +/–
: Adjust the subwoofer output level.
CENTER +/–
: Adjust the center speaker output level.
REAR•L +/–
: Adjust the left rear speaker output level.
REAR•R +/–
: Adjust the right rear speaker output level.
EFFECT
: Select the DAP effect level.
TEST
: Turn on or off the test tone output.
CONTROL
RM-SRX7022U REMOTE CONTROL
Note:
After adjusting sounds, press the corresponding source selecting
button or CONTROL to operate your target source by using the 10
keys; otherwise, the 10 keys cannot be used for operating your target
source.
When you press one of the following buttons, the remote
control operation mode appears on the display window.
Tuner
A/V CONTROL RECEIVER
You can always use the following buttons:
FM/AM
Ex.: When you press CD.
Buttons on the Remote Control
FM/AM
CD
PHONO
TAPE/CDR
DVD
DVD MULTI
TV/DBS
VCR
CATV/DBS CONTROL
CONTROL
SOUND
Remote Control Operation Mode
TUNER
CD
PHONO
TAPE
DVD
DVD
TV
VCR
DBS
VCR or TAPE or CDDSC
SOUND
: Alternate between FM and AM.
After pressing FM/AM, you can use the following buttons for tuner
operations:
1 – 10, +10
: Select a preset channel number directly.
• For channel number 5, press 5.
• For channel number 15, press +10, then 5.
• For channel number 20, press +10, then 10.
TUNING +/–
: Tune into stations.
FM MODE
: Change the FM reception mode.
34
EN30-42.RX-7020V[A]3
34
02.4.17, 5:16 PM
Operating JVC’s Audio/Video Components
CD player
Turntable
After pressing CD, you can use the following buttons for CD
operations:
After pressing PHONO, you can perform the following operations
on the turntable:
3
: Start playback.
3
: Start playing.
4
: Return to the beginning of the current
(or previous) track.
7
: Stop operations.
¢
: Skip to the beginning of the next track.
7
: Stop playback.
Cassette deck
8
: Pause playback. To release it, press 3.
1 – 10, +10
: Select a track number directly.
• For track number 5, press 5.
• For track number 15, press +10, then 5.
• For track number 20, press +10, then 10.
After pressing TAPE/CDR (or CONTROL repeatedly until “TAPE”
appears on the display window), you can use the following buttons
for cassette deck operations:
3
: Start playback.
FF
: Fast wind a tape from left to right.
REW
: Fast wind a tape from right to left.
CD changer
7
: Stop playback or recording.
After pressing CONTROL repeatedly until “CDDSC” appears on
the display window, you can perform the following operations on
the CD changer:
8
: Pause playback. To release it, press 3.
REC PAUSE
: Press this button to enter recording pause.
Press this button then 3 to start recording.
3
: Start playback.
4
: Return to the beginning of the current
(or previous) track.
¢
: Skip to the beginning of the next track.
7
: Stop playback.
8
: Pause playback. To release it, press 3.
1 – 6, 7/P
: Select the number of a disc installed in a CD
changer.
After pressing CD, you can perform the following operations on the
CD changer:
1 – 10, +10
: Select a track number directly.
• For track number 5, press 5.
• For track number 15, press +10, then 5.
• For track number 20, press +10, then 10.
• For track number 30, press +10, +10, then 10.
Example:
• Selecting disc number 4, track number 12, and starting playback.
1. Press CONTROL repeatedly until “CDDSC” appears on the
display window, then press 4.
2. Press CD, then press +10, 2.
If your CD changer is of 200-disc loading capability (except for
XL-MC100 and XL-MC301),
you can do the following operations using the number buttons after
pressing CD:
1 Select a disc number.
2 Then select a track number (always enter two digits).
3 Start playback.
Examples:
• Selecting disc number 3, track number 2, and starting playback.
Press 3, then, 0, 2, then 3.
• Selecting disc number 10, track number 5, and starting playback.
Press 1, 0, then, 0, 5, then 3.
• Selecting disc number 105, track number 12, and starting
playback.
Press 1, 0, 5, then 1, 2, then 3.
Notes:
• Before starting the above operations, make sure that you have
changed the source name correctly. See page 11.
• You can use either TAPE/CDR button or CONTROL button to
activate the buttons listed above. If you press TAPE/CDR, the
playing source also changes. On the other hand, if you press
CONTROL repeatedly to select “TAPE,” the playing source does not
change.
CD recorder
After pressing TAPE/CDR (or CONTROL repeatedly until “TAPE”
appears on the display window), you can use the following buttons
for CD recorder operations:
3
: Start playback.
4
: Return to the beginning of the current
(or previous) track.
¢
: Skip to the beginning of the next track.
7
: Stop playback.
8
: Pause playback. To release it, press 3.
REC PAUSE
: Press this button to enter recording pause.
Press this button then 3 to start recording.
Notes:
• Before starting the above operations, make sure that you have
changed the source name correctly. See page 11.
• “TAPE” appears on the display window even though you have
changed the source name to “CDR.”
• You can use either TAPE/CDR button or CONTROL button to
activate the buttons listed above. If you press TAPE/CDR, the
playing source also changes. On the other hand, if you press
CONTROL repeatedly to select “TAPE,” the playing source does not
change.
35
EN30-42.RX-7020V[A]3
35
02.4.17, 5:16 PM
Operating Video Components
DVD player
After pressing DVD or DVD MULTI (source selecting button), you
can use the following buttons for DVD operations:
IMPORTANT:
To operate JVC’s video components using this remote control:
• You need to connect JVC’s video components through the AV
COMPU LINK terminals (see page 32) in addition to the
connections using cables with RCA pin plugs (see pages 7 and 8).
• Some JVC’s VCRs can accept two types of the control signals —
remote code “A” and “B.” Before using this remote control, make
sure that the remote control code of the VCR connected to the
VCR jacks is set to code “A.”
• When using the remote control:
– For the DVD player and VCR operations, aim the remote control
directly at the remote sensor on each component, not on the
receiver.
– For the TV having the AV COMPU LINK terminal, aim the remote
control directly at the remote sensor on the TV.
3
: Start playback.
4
: Return to the beginning of the current
(or previous) track.
¢
: Skip to the beginning of the next track.
7
: Stop playback.
8
: Pause playback. To release it, press 3.
DVD menu operations
After pressing DVD or DVD MULTI
(source selecting button), you can use
the following buttons for DVD menu
operations:
– CENTER +
EFFECT
1
2
3
MENU
– REAR • L +
TEST
4
5
6
ENTER
– REAR • R +
7/P
VCR
You can always perform the following operations:
VCR
8
9
– SUB WOOFER +
10
0
+10
RETURN
FM MODE
100+
: Turn on or off a VCR.
After pressing VCR (or CONTROL repeatedly until “VCR” appears
on the display window), you can use the following buttons for VCR
operations:
MENU
: Display or erase the menu screen.
5/∞
∞/3
3/2
2
: Select an item on the menu screen.
ENTER
: Enter a selected item.
3
: Start playback.
FF
: Fast wind a tape.
REW
: Rewind a tape.
TV
7
: Stop playback or recording.
You can always perform the following operations:
8
: Pause playback. To release it, press 3.
1 – 9, 0
: Select a TV channel on the VCR.
REC PAUSE
: Press this button to enter recording pause.
Press this button then 3 to start recording.
CH +/–
: Change the TV channels on the VCR.
TV
: Turn on or off a TV or a CATV converter.
TV/VIDEO
: Change the input mode (TV tuner and video
input).
TV VOL +/–
: Adjust the volume.
After pressing TV/DBS (source selecting button), you can use the
following buttons for TV operations:
Note:
You can use either VCR button or CONTROL button to activate the
buttons listed above. If you press VCR, the playing source also
changes. On the other hand, if you press CONTROL repeatedly to
select “VCR,” the playing source does not change.
CH +/–
: Change the channels.
1 – 9, 0, +10 (100+)
: Select a channel.
RETURN (10)
: Function as the RETURN button.
36
EN30-42.RX-7020V[A]3
36
02.4.17, 5:16 PM
Operating Other Manufacturers’ Video Equipment
By changing the transmittable signals, you can use the remote
control supplied for this unit to operate other manufacturers’
equipment.
• Refer also to the manuals supplied for the other products.
• To operate these components with the remote control, first you
need to set the manufacturers’ code each for TV, CATV converter,
VCR and DVD player.
• After replacing batteries of the remote control, set the
manufacturers’ codes again.
Manufacturers’ codes for TV
Manufacturer
JVC
AKAI
BLAUPUNKT
FISHER
GRUNDIG
HITACHI
IRADDIO
ITT/NOKIA
LOEWE
MAGNAVOX
METS
MITSUBISHI
MIVAR
NORDMENDE
OKANO
PANASONIC
PHILIPS
QUELLE
To change the transmittable signals
for operating a TV
1 Press and hold TV .
2 Press TV/DBS.
3 Enter manufacturer’s codes using buttons 1 – 9,
and 0.
4 Release TV .
Now, you can perform the following operations on the TV.
TV
: Turn on or off the TV.
TV/VIDEO
: Set the input mode (either TV or VIDEO).
TV VOL +/–
: Adjust the volume.
RCA/PROSCAN
SABA
SAMSUNG
SANYO
SCHNEIDER
SHARP
SONY
TELEFUNKEN
THOMSON
TOSHIBA
ZENITH
After pressing TV/DBS, you can perform the following
operations on the TV:
CH +/–
: Change the channels.
1 – 9, 0, +10 (100+) : Select a channel.
10
: Function as the ENTER button.
Codes
00*, 02, 13, 14, 47, 74
01, 02
03, 04
01, 05
03, 06, 07
08, 09, 10, 49
02
11, 12
06, 15, 16
08, 17, 49
50, 51, 52, 53
08, 18, 19, 20
21
22, 23
15
24, 25, 26, 27, 76
15, 17, 28, 75
52, 53, 54, 55, 56, 57, 58,
59, 60, 61, 62, 63, 64, 65,
66, 67
08, 24, 29, 30, 31, 48
32, 33, 68, 69, 70
06, 08, 16, 34, 35, 49
01, 05
02, 15, 36
37, 38, 77
39
40, 41, 42, 69
71, 72
37, 43, 44
45, 46
* “00” is the initial setting.
Note:
Refer also to the manual supplied with your TV.
5 Try to operate your TV by pressing TV
Manufacturers’ codes are subject to change without
notice. If they are changed, this remote control cannot
operate the equipment.
.
When your TV turns on or off, you have entered the correct
codes.
If there are more than one code listed for your brand of TV,
try each one until the correct one is entered.
To change the transmittable signals for
operating a CATV converter or DBS tuner
1 Press and hold CATV/DBS .
2 Press CATV/DBS CONTROL.
3 Enter manufacturer’s codes using buttons 1 – 9,
and 0.
4 Release CATV/DBS .
Now, you can perform the following operations on the CATV
converter or DBS tuner.
CATV/DBS
: Turn on or off the CATV converter or DBS tuner.
After pressing CATV/DBS CONTROL, you can perform the
following operations on the CATV converter or DBS tuner:
CH +/–
: Change the channels.
1 – 9, 0, +10 (100+) : Select the channels.
10
: Function as the ENTER button.
Note:
Refer also to the manual supplied with your CATV converter or
DBS tuner.
37
EN30-42.RX-7020V[A]3
37
02.4.17, 5:16 PM
5 Try to operate your CATV converter or DBS
tuner by pressing CATV/DBS .
When your CATV converter or DBS tuner turns on or off, you
have entered the correct codes.
If there are more than one code listed for your brand of
CATV converter or DBS tuner, try each one until the correct
one is entered.
Note:
To change the transmittable signals for
operating a VCR
1 Press and hold VCR
.
2 Press VCR.
3 Enter manufacturer’s codes using buttons 1 – 9,
and 0.
4 Release VCR .
Now, you can perform the following operations on the VCR.
You cannot use both the CATV converter and DBS tuner at the same
time.
Manufacturers’ codes for CATV converter
Manufacturer
Codes
GENERAL INSTRUMENT 06, 07, 08, 09, 10,
11, 12, 13, 14, 29
HAMLIN/REGAL
01, 02, 03, 04, 05
JERROLD
06, 07, 08, 09, 10,
11, 12, 13, 14
OAK
15, 16, 17
PANASONIC
18, 19, 20
PIONEER
21, 22
SCIENTIFIC ATLANTA
23, 24, 25
TOCOM
26
ZENITH
27, 28
Manufacturers’ codes are subject to change without
notice. If they are changed, this remote control cannot
operate the equipment.
VCR
: Turn on or off the VCR.
After pressing VCR, you can perform the following operations
on the VCR:
CH +/–
: Change the channels.
1 – 9, 0, +10 (100+)
: Select the channels.
10
: Function as ENTER button.
3
: Start playback.
FF
: Fast-wind a tape.
REW
: Rewind a tape.
7
: Stop playback or recording.
8
: Pause playback. To release it, press 3.
REC PAUSE
: Press this button to enter recording
pause.
Then press 3 to start recording.
Note:
Refer also to the manual supplied with your VCR.
Manufacturers’ codes for DBS tuner
Manufacturer
Codes
JVC
AMSTRAD
BLAUPUNKT
ECHOSTAR
GOLDSTAR
GRUNDIG
HIRSHMANN
INSTRUMENT
ITT/NOKIA
KATHREIN
NEC
ORBITECH
PHILIPS
RCA
SAMSUNG
SCHWAIGER
SIEMENS
SONY
TECHNISAT
56, 57*, 67
43, 44, 45, 46, 47
30
50, 51, 67
31
32, 33
48, 52, 53, 55
68
34
52, 58, 61, 62, 63
35, 36
48
37, 38
65
39, 40
61, 64
41, 42
66
48
5 Try to operate your VCR by pressing
VCR .
When your VCR turns on or off, you have entered the correct
codes.
If there are more than one code listed for your brand of
VCR, try each one until the correct one is entered.
* “57” is the initial setting.
Manufacturers’ codes are subject to change without
notice. If they are changed, this remote control cannot
operate the equipment.
TO BE CONTINUED TO THE NEXT PAGE
38
EN30-42.RX-7020V[A]3
38
02.4.17, 5:17 PM
Operating Other Manufacturers’ Video Equipment
Manufacturers’ codes for VCR
Manufacturer
Codes
JVC
AIWA
BELL & HOWELL
BLAUPUNKT
CGM
EMERSON
FISHER
FUNAI
GE
GOLDSTAR
GOODMANS
GRUNDIG
HITACHI
LOEWE
MAGNAVOX
MITSUBISHI
NEC
NOKIA
NORDMENDE
ORION
PANASONIC
PHILIPS
PHONOLA
RCA/PROSCAN
SABA
SAMSUNG
SANYO
SHARP
SIEMENS
SONY
TELEFUNKEN
TOSHIBA
ZENITH
00*, 26, 27, 28, 29, 58
01, 02
03
04, 05
06, 07
08, 10, 11, 12, 64, 65
03, 14, 15, 16, 17
01
18, 19, 20
07
13, 21
06, 22
18, 23, 24, 25, 66
07, 21
04, 19, 24
30, 31, 32, 33, 34, 35
26, 27
03, 36
38
09
19, 24, 39, 40
04, 19, 21, 24, 41, 42
21
04, 18, 19, 23, 24, 43, 44,
45
38, 46
45, 47, 59, 61, 62, 63
03, 48, 49
37, 50
03, 51
52, 53, 54
55, 60
43, 44
57
* “00” is the initial setting.
Manufacturers’ codes are subject to change without
notice. If they are changed, this remote control cannot
operate the equipment.
To change the transmittable signals for
operating a DVD player
1 Press and hold AUDIO .
2 Press DVD.
3 Enter manufacturer’s codes using buttons 1 – 9,
and 0.
4 Release AUDIO .
Now, you can use the following buttons on the DVD player after
pressing DVD or DVD MULTI (source selecting button).
3
: Start playback.
7
: Stop playback.
¢
: Skip to the beginning of the next track.
4
: Return to the beginning of the current (or
previous) track.
8
: Pause playback. To release it, press 3.
DVD menu operations
After pressing DVD or DVD MULTI
(source selecting button), you can
use the following buttons for DVD
menu operations:
– CENTER +
EFFECT
1
2
3
MENU
– REAR • L +
TEST
4
5
6
ENTER
– REAR • R +
7/P
8
9
– SUB WOOFER +
10
0
+10
RETURN
FM MODE
100+
MENU
: Display or erase the menu screen.
5/∞
∞/3
3/2
2
: Select an item on the menu screen.
ENTER
: Enter a selected item.
5 Try to operate your DVD player by pressing
AUDIO .
When your DVD player turns on or off, you have entered the
correct codes.
If there are more than one code listed for your brand of DVD
player, try each one until the correct one is entered.
Manufacturers’ codes for DVD player
Manufacturer
JVC
DENON
PANASONIC
PHILIPS
PIONEER
RCA
SAMSUNG
SONY
TOSHIBA
YAMAHA
Codes
00*, 02
01
03
13
04, 05, 06
07
08
09
10
11, 12
* “00” is the initial setting.
Manufacturers’ codes are subject to change without
notice. If they are changed, this remote control cannot
operate the equipment.
39
EN30-42.RX-7020V[A]3
39
02.4.17, 5:17 PM
Troubleshooting
Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC’s service center.
PROBLEM
POSSIBLE CAUSE
SOLUTION
The power does not come on.
The power cord is not plugged in.
Plug the power cord into an AC outlet.
No sound from speakers.
Speaker signal cables are not connected.
Check speaker wiring and reconnect if
necessary.
The SPEAKERS ON/OFF 1 and 2 buttons
are not set correctly.
Press SPEAKERS ON/OFF 1 and 2 buttons
correctly.
An incorrect source is selected.
Select the correct source.
Muting is activated.
Press MUTING to cancel the mute.
An incorrect input mode (analog or
digital) is selected.
Select the correct input mode (analog or
digital).
Connections are incorrect.
Check connections.
For analog connections, see pages 6 – 8.
For digital connections, see page 9.
Speaker signal cables are not connected
properly.
Check speaker wiring and reconnect if
necessary.
The balance is set to one extreme.
Adjust the balance properly (see page 19).
Incoming signal is too weak.
Connect an outdoor FM antenna or contact
your dealer.
The station is too far away.
Select a new station.
An incorrect antenna is used.
Check with your dealer to be sure you have
the correct antenna.
Antennas are not connected properly.
Check connections.
Occasional cracking noise during FM
reception.
Ignition noise from automobiles.
Move the antenna farther from automobile
traffic.
Howling during record playing
Your turntable is too close to speakers.
Move speakers away from the turntable.
Noise is heard.
An earth (H) cable is not connected to the
AM (H) terminal on the rear panel.
Connect the cable to the AM (H) terminal on
the rear panel.
“OVERLOAD” starts flashing on the
display.
Speakers are overloaded because of high
volume.
on the front
1. Press STANDBY/ON
panel to turn off the receiver.
2. Stop the playback source.
3. Turn on the receiver again, and adjust the
volume.
Speakers are overloaded because of short
circuit of speaker terminals.
on the front panel,
Press STANDBY/ON
then check the speaker wiring.
If “OVERLOAD” does not disappear, unplug
the AC power cord, then plug it back again.
If speaker wiring is not short-circuited, contact
your dealer.
“DSP MICOM NG” starts flashing on the
display.
The built-in microcomputer is not
functioning correctly.
on the front panel to
Press STANDBY/ON
turn off the receiver. After unplugging the
power cord, consult your dealer.
The STANDBY lamp lights up after
turning on the power, but soon the
receiver turns off (into standby mode).
The receiver is overloaded because of a
high voltage.
on the front panel to
Press STANDBY/ON
turn off the receiver. After unplugging the
power cord, consult your dealer.
Remote control does not work.
There is an obstruction in front of the
remote sensor on the receiver.
Remove the obstruction.
Batteries are weak.
Replace batteries.
The remote control is not ready for your
intended operation.
Press SOUND or source selecting buttons
first, then press the button you want to use.
(See pages 34 – 39).
Sound from one speaker only.
Continuous hiss or buzzing during FM
reception.
Remote control does not operate as you
intend.
40
EN30-42.RX-7020V[A]3
40
02.4.17, 5:17 PM
Specifications
Designs & specifications are subject to change without notice.
Amplifier
Output Power
At Stereo operation:
Front channels:
100 W per channel, min. RMS, Both channels driven into 8 Ω at
1 kHz, with no more than 0.9% total harmonic distortion.
At Surround operation:
Audio
Audio Input Sensitivity/Impedance (1 kHz):
Audio Input (DIGITAL IN)* :
Front channels:
100 W per channel, min. RMS, driven into 8 Ω at 1 kHz, with no
more than 0.8% total harmonic distortion.
Center channel:
100 W, min. RMS, driven into 8 Ω at 1 kHz, with no more than
0.8% total harmonic distortion.
Rear channels:
100 W per channel, min. RMS, driven into 8 Ω at 1 kHz, with no
more than 0.8% total harmonic distortion.
PHONO (MM):
2.7 mV/47 kΩ
CD, TAPE/CDR, VCR, TV SOUND/DBS, DVD:
220 mV/47 kΩ
Coaxial: DIGITAL 1 (DVD):
0.5 V (p-p)/75 Ω
Optical: DIGITAL 2 (CD), DIGITAL 3 (TV), DIGITAL 4 (CDR):
–21 dBm to –15 dBm (660 nm ±30 nm)
* Corresponding to Linear PCM, Dolby Digital, and DTS Digital Surround
(with sampling frequency — 32 kHz, 44.1 kHz, 48 kHz).
Audio Output Level:
Digital output:
TAPE/CDR, VCR:
220 mV
Optical: DIGITAL OUTPUT
Signal wave length: 660 nm
Output level: –21 dBm to –15 dBm
Signal-to-Noise Ratio (’66 IHF/DIN):
Frequency Response (8 Ω):
PHONO (MM):
70 dB/ 66 dB (at REC OUT)
CD, TAPE/CDR, VCR, TV SOUND/DBS, DVD:
87 dB/67 dB
PHONO (MM):
20 Hz to 20 kHz (±1 dB)
CD, TAPE/CDR, VCR, TV SOUND/DBS, DVD:
20 Hz to 20 kHz (±1 dB)
RIAA Phono Equalization:
Bass boost:
Tone Control:
±1 dB(20 Hz to 20 kHz)
+3 dB ±1 dB at 100 Hz
Bass (100 Hz):
Treble (10 kHz):
±10 dB
±10 dB
Video
Video Input Sensitivity/Impedance:
Composite video:
S-video:
Component video:
Video Output Level/Impedance:
Composite video:
S-video:
Component video:
Synchronization:
Signal-to-Noise Ratio:
DVD, VCR, DBS:
DVD, VCR, DBS:
DVD, DBS:
VCR, MONITOR OUT:
VCR, MONITOR OUT:
MONITOR OUT:
(Y: luminance):
(C: chrominance, burst):
(Y: luminance):
(PB/CB, PR/CR):
1 V(p-p)/75 Ω
1 V(p-p)/75 Ω
0.286 V(p-p)/75 Ω
1 V(p-p)/75 Ω
0.7 V(p-p)/75 Ω
(Y: luminance):
(C: chrominance, burst):
(Y: luminance):
(PB/CB, PR/CR):
1 V(p-p)/75 Ω
1 V(p-p)/75 Ω
0.286 V(p-p)/75 Ω
1 V(p-p)/75 Ω
1 V(p-p)/75 Ω
Negative
45 dB
41
EN30-42.RX-7020V[A]3
41
02.4.17, 5:17 PM
FM tuner (IHF)
Tuning Range:
87.50 MHz to 108.00 MHz
Usable Sensitivity:
Monaural:
17.0 dBf (1.95 µV/75 Ω)
50 dB Quieting Sensitivity:
Monaural:
Stereo:
21.3 dBf (3.2 µV/75 Ω)
41.3 dBf (31.5 µV/75 Ω)
Signal-to-Noise Ratio (IHF-A weighted):
Monaural:
Stereo:
78 dB at 85 dBf
73 dB at 85 dBf
Total Harmonic Distortion:
Monaural:
Stereo:
0.4% at 1 kHz
0.6% at 1 kHz
Stereo Separation at REC OUT:
Alternate Channel Selectivity:
Frequency Response:
35 dB at 1 kHz
45 dB: (±400 kHz)
30 Hz to 15 kHz: (+0.5 dB, –3 dB)
AM tuner
Tuning Range:
Usable Sensitivity:
Signal-to-Noise Ratio:
522 kHz to 1 629 kHz
Loop antenna:
400 µV/m
50 dB (100 mV/m)
General
Power Requirements:
AC 240 V ,
adjustable with the voltage selector, 50 Hz/60 Hz
Power Consumption:
200 W (at operation)
2 W (in standby mode)
Dimensions (W x H x D):
Mass:
435 mm x 146.5 mm x 425.5 mm
9.8 kg
42
EN30-42.RX-7020V[A]3
42
02.4.17, 5:17 PM
VICTOR COMPANY OF JAPAN, LIMITED
V
EN
RX-7020V[A]_COVER2
J
2
02.4.9, 3:46 PM
C
0402NHMMDWJEIN