AUDIO/VIDEO CONTROL RECEIVER
RECEPTEUR DE COMMANDE AUDIO/VIDEO
RX-7520VBK
RX-7520V AUDIO/VIDEO CONTROL RECEIVER
FM/AM TUNING
FM/AM PRESET
FM MODE
STANDBY
COMPULINK
Remote
MASTER VOLUME
MEMORY
STANDBY/ON
SURROUND ON/OFF
INPUT
ANALOG/DIGITAL
BASS BOOST
ADJUST SETTING
FM MODE
DVD MULTI
DVD
VCR
TV SOUND
TAPE/CDR
FM
AM
INPUT ATT
SURROUND MODE
CONTROL
DOWN
UP
SPEAKERS ON/OFF
1
2
CD
SOURCE NAME
PHONES
INSTRUCTIONS
MANUAL D’INSTRUCTIONS
For Customer Use:
Enter below the Model No. and Serial
No. which are located either on the rear,
bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
LVT0852-002A
[C]
RX-7520VBK[C]Cover.pm5
1
02.2.12, 9:30 PM
Warnings, Cautions and Others/
Mises en garde, précautions et indications diverses
Caution –– STANDBY/ON
button!
Disconnect the mains plug to shut the power off completely. The STANDBY/ON
button in any position
does not disconnect the mains line. The power can be
remote controlled.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
!
Attention –– Commutateur STANDBY/ON
Déconnecter la fiche de secteur pour couper
complètement le courant. Le commutateur
STANDBY/ON
ne coupe jamais complètement la
ligne de secteur, quelle que soit sa position. Le courant
peut être télécommandé.
The lightning flash with arrowhead symbol,
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
For U.S.A.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
ATTENTION
Afin d’éviter tout risque d’électrocution, d’incendie, etc.:
1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir
le coffret de l’appareil.
2. Ne pas exposer l’appareil à la pluie ni à l’humidité.
Changes or modifications not expressly approved by the
manufacturer for compliance could void the user’s
authority to operate the equipment.
– G-1 –
RX-7520VBK[C]Safety.pm5
1
02.2.14, 4:31 PM
English
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT
ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS
LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQUAU FOND
For Canada/pour Le Canada
THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B
LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL APPARATUS
AS SET OUT IN THE INTERFERENCE-CAUSING EQUIPMENT
STANDARD ENTITLED “DIGITAL APPARATUS,” ICES-003 OF THE
DEPARTMENT OF COMMUNICATIONS.
CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE BRUITS
RADIOELECTRIQUES APPLICABLES AUX APPAREILS NUMERIQUES
DE CLASSE B PRESCRITES DANS LA NORME SUR LE MATERIEL
BROUILLEUR; “APPAREILS NUMERIQUES”, NMB-003 EDICTEE PAR
LE MINISTRE DES COMMUNICATIONS.
Caution: Proper Ventilation
Attention: Ventilation Correcte
To avoid risk of electric shock and fire and to protect from
damage.
Locate the apparatus as follows:
Front:
No obstructions open spacing.
Sides:
No obstructions in 10 cm from the sides.
Top:
No obstructions in 10 cm from the top.
Back:
No obstructions in 15 cm from the back.
Bottom:
No obstructions, place on the level surface.
In addition, maintain the best possible air circulation as
illustrated.
Pour éviter les chocs électriques, l’incendie et tout autre
dégât.
Disposer l’appareil en tenant compte des impératifs suivants
Avant:
Rien ne doit gêner le dégagement
Flancs:
Laisser 10 cm de dégagement latéral
Dessus:
Laisser 10 cm de dégagement supérieur
Arrière:
Laisser 15 cm de dégagement arrière
Dessous: Rien ne doit obstruer par dessous; poser
l’appareil sur une surface plate.
Veiller également à ce que l’air circule le mieux possible
comme illustré.
Spacing 15 cm or more
Dégagement de 15 cm ou plus
RX-7520VBK
Wall or obstructions
Mur, ou obstruction
Front
Avant
Stand height
15 cm or more
Hauteur du socle:
15 cm ou plus
Floor
Plancher
– G-2 –
RX-7520VBK[C]Safety.pm5
2
02.2.14, 4:31 PM
Français
For Canada/pour le Canada
English
Table of Contents
Parts Identification ...................................... 2
Getting Started ........................................... 3
Before Installation ...................................................................... 3
Checking the Supplied Accessories ........................................... 3
Putting Batteries in the Remote Control .................................... 3
Connecting the FM and AM Antennas ....................................... 4
Connecting the Speakers ............................................................ 5
Connecting Audio/Video Components ....................................... 6
Connecting the Power Cord ....................................................... 9
Basic Operations ....................................... 10
Turning On the Power .............................................................. 10
Selecting the Source to Play ..................................................... 10
Adjusting the Volume ............................................................... 11
Selecting the Front Speakers .................................................... 11
Listening Only with Headphones ............................................. 12
Turning Off the Sounds Temporarily—Muting ........................ 12
Changing the Display Brightness ............................................. 12
Turning Off the Power with the Sleep Timer ........................... 12
Basic Settings ........................................... 14
Setting the Digital Input (DIGITAL IN) Terminals ................. 14
Selecting the Analog or Digital Input Mode ............................ 14
Setting the Video Input Terminal ............................................. 16
Setting the Speaker Information ............................................... 16
Sound Adjustments .................................... 19
Attenuating the Input Signal .................................................... 19
Adjusting the Front Speakers Output Balance ......................... 19
Adjusting the Tone ................................................................... 20
Adjusting the Subwoofer Output Level .................................... 20
Reinforcing the Bass ................................................................ 20
Tuner Operations ....................................... 21
Tuning in Stations Manually .................................................... 21
Using Preset Tuning ................................................................. 21
Selecting the FM Reception Mode ........................................... 22
Creating Realistic Sound Fields ................... 23
About Relations between Speaker Layouts and
Surround Modes ................................................................. 25
Using Dolby Pro Logic II, Dolby Digital
and DTS Digital Surround ................................................. 26
Using DAP Modes and All Channel Stereo ............................. 28
Using DVD MULTI Playback Mode ................ 30
Activating DVD MULTI Playback Mode ................................ 30
COMPU LINK Remote Control System ......... 31
AV COMPU LINK Remote Control System .... 32
Operating JVC’s Audio/Video
Components .......................................... 34
Operating Audio Components .................................................. 34
Operating Video Components .................................................. 36
Operating Other Manufacturers’ Video
Equipment ............................................ 37
Troubleshooting ......................................... 40
Specifications ............................................ 41
This mark indicates that the remote control CAN
ONLY be used for the operation explained.
Remote
NOT
This mark indicates that the remote control CANNOT
be used for the operation explained. Use buttons on
the front panel.
1
EN01-09.RX-7520V[C]f.pm5
1
02.2.14, 4:31 PM
English
Parts Identification
Front Panel
2
3
FM/AM TUNING
FM/AM PRESET
1
45
7 89
6
p
RX-7520V AUDIO/VIDEO CONTROL RECEIVER
FM MODE
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
STANDBY
MEMORY
SPK 1 2
L
C
OPERATION BASS BOOST
TUNED STEREO
AUTO MUTING SLEEP
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
R
VOLUME
S.WFR LFE
LS
S
MASTER VOLUME
RS
CH-
STANDBY/ON
SURROUND ON/OFF
INPUT
ANALOG/DIGITAL
BASS BOOST
ADJUST SETTING
DVD MULTI
DVD
VCR
TV SOUND
CD
TAPE/CDR
FM
AM
INPUT ATT
SURROUND MODE
CONTROL
DOWN
UP
SPEAKERS ON/OFF
1
2
SOURCE NAME
PHONES
q
w e r
t
y
u
i
o
See pages in the parentheses for details.
Front Panel
Remote Control
1
w
2
e
3
PTY–PTY SEARCH–PTY
4
t
y
u
i
o
r
5
6
t
7
1
2
3
4
5
6
7
8
9
p
q
w
e
r
FM MODE
y
u
8
9
i
p
o
q
;
STANDBY/ON
button and STANDBY lamp (10)
FM/AM TUNING 5/∞ buttons (21)
FM/AM PRESET 5/∞ buttons (21, 22)
FM MODE button (22)
MEMORY button (21, 22)
Display (10)
ADJUST button (19, 20, 27 – 30)
Remote sensor (3)
SETTING button (14, 16 – 18)
MASTER VOLUME control (11)
PHONES jack (12)
SURROUND ON/OFF button (25, 27, 29)
SURROUND MODE button (25, 27, 29)
• INPUT ANALOG/DIGITAL button (15)
• INPUT ATT button (19)
SPEAKERS ON/OFF 1 and 2 buttons (11, 12)
BASS BOOST button (20)
SOURCE NAME button (11)
Source selecting buttons (10, 11, 14, 21, 22, 30)
DVD MULTI, DVD, VCR, TV SOUND, CD, TAPE/CDR, FM, AM
CONTROL UP5/DOWN∞ buttons (14, 16 – 20, 27 – 30)
Remote Control
1 TV/CATV selector (36, 37)
2 •10 keys for selecting preset channels (22)
•10 keys for adjusting sound (20, 27, 28, 30, 34)
•10 keys for operating audio/video components (34 – 37)
3 SOUND button (20, 27, 28, 30, 34)
4 Operating buttons for audio/video components (34 – 36, 38, 39)
5 REC PAUSE button (35, 36, 38)
6 Source selecting buttons (10, 11, 14, 21, 22, 30, 34 – 39)
TAPE/CDR, CD, DVD, DVD MULTI, FM/AM, TV SOUND, VCR
7 FM MODE button (22)
8 DIMMER button (12)
9 TV/VIDEO button (36, 37)
p VCR CH (channel) +/– buttons (36, 38)
q TV/CATV CH (channel) +/– buttons (36, 37)
w STANDBY/ON
buttons (10, 33, 36 – 39)
AUDIO, TV/CATV, VCR, DVD
e SLEEP button (12)
r CD–DISC button (35)
t ANALOG/DIGITAL button (15)
y BASS BOOST button (20)
u SURROUND ON/OFF and SURROUND MODE buttons (25, 28)
i MUTING button (12)
o VOLUME +/– button (11)
; TV VOLUME +/– buttons (36, 37)
2
EN01-09.RX-7520V[C]f.pm5
2
02.2.14, 4:31 PM
Before Installation
General Precautions
• DO NOT insert any metal object into the unit.
• DO NOT disassemble the unit or remove screws, covers, or
cabinet.
• DO NOT expose the unit to rain or moisture.
English
Getting Started
Putting Batteries in the Remote Control
Before using the remote control, put two supplied batteries first.
• When using the remote control, aim the remote control directly at
the remote sensor on the unit.
1 On the back of the remote control, remove the
battery cover.
Locations
• Install the unit in a location that is level and protected from
moisture.
• The temperature around the unit must be between –5˚C and 35˚C
(23˚F and 95˚F).
• Make sure there is good ventilation around the unit. Poor
ventilation could cause overheating and damage the unit.
Handling the unit
• DO NOT touch the power cord with wet hands.
• DO NOT pull on the power cord to unplug the cord. When
unplugging the cord, always grasp the plug so as not to damage
the cord.
• Keep the power cord away from the connecting cords and the
antenna. The power cord may cause noise or screen interference. It
is recommended to use a coaxial cable for antenna connection,
since it is well-shielded against interference.
• When a power failure occurs, or when you unplug the power cord,
the preset settings such as preset FM/AM channels and sound
adjustments may be erased in a few days.
2 Insert batteries.
• Make sure to match the polarity: (+) to (+) and (–) to (–).
Checking the Supplied Accessories
Check to be sure you have all of the following supplied accessories.
The number in the parentheses indicates the quantity of the pieces
supplied.
3 Replace the cover.
• Remote Control (1)
• Batteries (2)
• AM Loop Antenna (1)
• FM Antenna (1)
If anything is missing, contact your dealer immediately.
If the range or effectiveness of the remote control decreases, replace
the batteries. Use two R6P(SUM-3)/AA(15F) type dry-cell batteries.
CAUTION:
Follow these precautions to avoid leaking or cracking cells:
• Place batteries in the remote control so they match the polarity:
(+) to (+) and (–) to (–).
• Use the correct type of batteries. Batteries that look similar may
differ in voltage.
• Always replace both batteries at the same time.
• Do not expose batteries to heat or flame.
3
EN01-09.RX-7520V[C]f.pm5
3
02.2.14, 4:31 PM
English
Getting Started
Connecting the FM and AM Antennas
AM Loop Antenna
(supplied)
Outdoor FM antenna (not supplied)
If FM reception is poor, connect outdoor
FM antenna.
75
FMAXIAL
CO
CO
Standard type
outdoor FM antenna
(not supplied)
Supplied FM
antenna
ANTENNA
75
FMAXIAL
or
FM 75
COAXIAL
FM antenna (supplied)
Extend the supplied FM antenna horizontally.
Snap the tabs on the loop
into the slots of the base
to assemble the AM loop
antenna.
AM
LOOP
AM
EXT
If AM reception is poor, connect
outdoor single vinyl-covered wire
(not supplied).
1
2
3
R
PR/C
B
PB/C
2
Y
NT
FROKERS
EA
SP
IDEO T
TV
EN R OU
ON
O
MP ONIT
CO
M
D
DV
NA
TEN FM 75IAL
AN
AX
CO
AV NKU LI
MP
-4
CO
NK
U LI O)
MP HR
CO(SYNC
R
VC
R
REAERS
EAK
SP
TER
CEN KER
EA
SP
+
–
T
+
OR
NIT
MOOUT
+
1
–
LEFT
RIGH
LEFT
T
D
DV
L1
ITA )
DIG(DVD
DIO
AU LEFT
L2
ITA
DIG
( CD
T
OU
T
ON
FR
INY)
(PLA
B
SUFER
O
WO
) (REC)
E
TAPR
/CD
L IN
ITA
DIG
R
VC
TV
LEFT
INY)
(PLA
DEO
S-VI
–
RIGH
CE
AN
N : ED
TIO IMP
CAU KER
SPEA 16
8
EO VIDEO
VID
AR
RE
T
RIGH
T
OU )
(REC
INY)
(PLA
D
UN
SO
V
TER
CEN
AM
EXIT
AM
OP
LO
T
OU )
(REC R
C
T
RIGH
CD
LEFT
FER
OO
BW
SU OUT
T
RIGH DIO
AU
AM antenna connection
Connect the supplied AM loop antenna to the AM LOOP
terminals.
Turn the loop until you have the best reception.
• If the reception is poor, connect an outdoor single vinylcovered wire (not supplied) to the AM EXT terminal. (Keep the
AM loop antenna connected.)
FM antenna connection
Notes:
Connect the supplied FM antenna to the FM 75 Ω COAXIAL
terminal as a temporary measure.
Extend the supplied FM antenna horizontally.
• If the reception is poor, connect an outdoor FM antenna (not
supplied). Before attaching a 75 Ω coaxial cable (with a
standard type connector), disconnect the supplied FM antenna.
• If the AM loop antenna wire is covered with vinyl,
remove the vinyl while twisting it as shown on the
right.
• Make sure the antenna conductors do not touch any
other terminals, connecting cords and power cord.
This could cause poor reception.
4
EN01-09.RX-7520V[C]f.pm5
4
02.2.14, 4:31 PM
+
–
E
NC
EDA
IMP 6
1
KER
SPEA : 8 32
N: 2
6
TIO
CAU 1 OR 2 :1
D
N
1 A
English
“NO” for the subwoofer, “LARGE” for the front speakers,
and “SMALL” for the center and rear speakers are initial
settings. To get best possible sound, change the subwoofer and
speaker settings to fit your listening conditions.
Connection diagram
FRONT
SPEAKERS
1
Connecting the Speakers
Speaker layout diagram
FRONT
SPEAKERS
1
Center
speaker
Left front
speaker
Subwoofer
Right front
speaker
2
+
+
–
–
RX-7020V AUDIO/VIDEO CONTROL RECEIVER
FM/AM TUNING
FM/AM PRESET
FM MODE
STANDBY
MASTER VOLUME
COMPULINK
Remote
MEMORY
RIGHT
D I G I T A L
SURROUND
SURROUND ON/OFF
INPUT
ANALOG/DIGITAL
BASS BOOST
ADJUST SETTING
DVD MULTI
DVD
VCR
TAPE/CDR
PHONO
TV SOUND/DBS
INPUT ATT
SOURCE NAME
SURROUND MODE
CONTROL
DOWN
UP
SPEAKERS ON/OFF
1
2
CD
LEFT
FM/AM
SOURCE NAME
PHONES
RIGHT
Left rear
speaker
LEFT
Right rear
speaker
After connecting the front, center, rear speakers and/or subwoofer,
set the speaker setting information properly to obtain the best
possible Surround effects. For details, see pages 16 to 18.
CAUTION:
Use speakers with the SPEAKER IMPEDANCE indicated by the
speaker terminals.
FRONT
SPEAKERS
2
Connecting speakers to the FRONT SPEAKERS 1 terminals
1
2
RIG
Connecting the front speakers
About the speaker impedance
The required speaker impedance of the front speakers does differ
depending on whether both the FRONT SPEAKERS 1 and FRONT
SPEAKERS 2 terminals are used or only one of them is used.
CASE 1 When you connect only one pair of front speakers
Front
speaker
1
4
1
1
RIG
RIG
HT
HT
LE
You can connect two pairs of front speakers (one pair to the FRONT
SPEAKERS 1 terminals, and the other pair to the FRONT
SPEAKERS 2 terminals).
Front
speaker
1
3
1
HT
LE
LE
FT
FT
FT
For each speaker, connect the (+) and (–) terminals on the rear panel
to the (+) and (–) terminals marked on the speakers.
1 Cut, twist and remove the insulation at the end of
each speaker signal cable (not supplied).
2 Turn the knob counterclockwise.
3 Insert the speaker signal cable.
4 Turn the knob clockwise.
Connecting speakers to the FRONT SPEAKERS 2 terminals
1
2
3
1
2
Use front speakers with 8 Ω – 16 Ω impedance.
CASE 2 When you connect two pairs of front speakers
Front
speaker
2
Front
speaker
1
Front
speaker
2
For each speaker, connect the (+) and (–) terminals on the rear panel
to the (+) and (–) terminals marked on the speakers.
Front
speaker
1
Use front speakers with 16 Ω – 32 Ω impedance.
1 Cut, twist and remove the insulation at the end of
each speaker cord.
2 Open the terminal (1), then insert the speaker
cord (2).
3 Close the terminal.
5
EN01-09.RX-7520V[C]f.pm5
5
02.2.14, 4:31 PM
English
Getting Started
Connecting Audio/Video Components
Connecting the rear and center speakers
Connect rear speakers to the REAR SPEAKERS terminals and a
center speaker to the CENTER SPEAKER terminals.
You can connect the following audio/video components to this unit.
Refer also to the manuals supplied with your components.
Center
speaker
CENTER
SPEAKER
Audio Components
• CD player*
• Cassette deck
or CD recorder*
REAR
SPEAKERS
+
Left rear
speaker
Turn off all components before connecting.
Right rear
speaker
Video Components
• VCR
• TV*
• DVD player*
* You can connect these components using the methods described in
“Analog connections” (below) or in “Digital connections” (see page 9).
Analog connections
Audio component connections
–
RIGHT
LEFT
Use the cables with RCA pin plugs (not supplied).
Connect the white plug to the audio left jack, and the red plug to the
audio right jack.
CAUTION:
1
2
4
3
RIG
If you connect a sound-enhancing device such as a graphic equalizer
between the source components and this receiver, the sound output
through this receiver may be distorted.
RIG
RIG
HT
HT
HT
LE
FT
LE
LE
FT
FT
CD player
For each speaker, connect the (+) and (–) terminals on the rear panel
to the (+) and (–) terminals marked on the speakers.
1 Cut, twist and remove the insulation at the end of
each speaker signal cable (not supplied).
2 Turn the knob counterclockwise.
3 Insert the speaker signal cable.
4 Turn the knob clockwise.
CD player
CD
OUT
(REC)
TAPE
CDR
To audio output
IN
(PLAY)
OUT
(REC)
VCR
IN
(PLAY)
Connecting the subwoofer speaker
TV SOUND
By connecting a subwoofer, you can enhance the bass or reproduce
the original LFE signals recorded on the digital software.
RIGHT
AUDIO
RIGHT
LEFT
FRONT
Powered subwoofer
DVD
SUB
WOOFER
CENTER
REAR
RIGHT
LEFT
SUBWOOFER
OUT
Connect the input jack of a powered subwoofer to the
SUBWOOFER OUT jack on the rear panel, using a cable with RCA
pin plugs (not supplied).
• Refer also to the manual supplied for your subwoofer.
Since bass sound is non-directional, you can place a
subwoofer wherever you like. Normally place it in front of
you.
6
EN01-09.RX-7520V[C]f.pm5
6
LEFT
AUDIO
02.2.14, 4:31 PM
Cassette deck
To audio input
To audio output
CD
OUT
(REC)
TAPE
CDR
Use the cables with RCA pin plugs (not supplied).
Connect the white plug to the audio left jack, the red plug to the
audio right jack, and the yellow plug to the video jack.
• If video components have S-video (Y/C-separation) and/or
component video (Y, PB/CB, PR/CR) terminals, connect them using
an S-video cable (not supplied) and/or component video cable (not
supplied). By using these terminals, you can get a better picture
quality in the order—Component video > S-video > Composite
video.
IMPORTANT:
IN
(PLAY)
OUT
(REC)
VCR
IN
(PLAY)
TV SOUND
RIGHT
LEFT
AUDIO
To audio input
English
Video component connections
Cassette deck or CD recorder
CD recorder
To audio output
Note:
This unit is equipped with the following video terminals: composite
video, S-video and component video terminals. You can use any of
these three to connect a video component.
However, remember that the video signals from one type of these
input terminals are output only through the video output
terminals of the same type.
Therefore, if a recording video component and a playing video
component are connected to the unit through the different types of
video terminals, you cannot record the picture from the playing
component onto the recording component. In addition, if the TV and a
playing video component are connected to the unit through the
different types of video terminals, you cannot view the playback
picture from the playing component on the TV.
You can connect either a cassette deck or a CD recorder to the
TAPE/CDR jacks. When connecting a CD recorder to the TAPE/CDR
jacks, change the source name, which will be shown on the display
when selected as the source. See page 11 for details.
If your audio components have a COMPU LINK jack
See also page 31 for detailed information about the connection and
the COMPU LINK remote control system.
VCR
COMPONENT VIDEO
MONITOR OUT
PB/CB
Y
PR/CR
CD
OUT
(REC)
MONITOR
OUT
AUDIO
RIGHT
TAPE
CDR
DVD
LEFT
VCR
FRONT
IN
(PLAY)
DVD
DVD
SUB
WOOFER
OUT
(REC)
VCR
CENTER
OUT
(REC)
VCR
REAR
IN
(PLAY)
RIGHT
IN
(PLAY)
LEFT
TV SOUND
S-VIDEO
VIDEO
VIDEO
RIGHT
LEFT
AUDIO
SUBWOOFER
OUT
C
F
B
A
D
E
G
S-VHS (or VHS) VCR
Å
ı
Ç
Î
‰
Ï
Ì
To left/right channel audio output
To left/right channel audio input
To composite video output
To S-video output
To S-video input
To composite video input
To component video output
Note:
See “Selecting the Video Input Terminal” on page 16 for details.
7
EN01-09.RX-7520V[C]f.pm5
7
02.2.14, 4:31 PM
English
Getting Started
DVD player
TV
• When you connect the DVD player with stereo output jacks:
COMPONENT VIDEO
MONITOR OUT
Y
PB/CB
PR/CR
DVD player
CD
OUT
(REC)
MONITOR
OUT
AUDIO
D
DVD
DVD
RIGHT
TAPE
CDR
LEFT
C
VCR
IN
(PLAY)
FRONT
OUT
(REC)
SUB
WOOFER
DVD
DVD
VCR
CENTER
OUT
(REC)
VCR
REAR
IN
(PLAY)
B
A
RIGHT
IN
(PLAY)
LEFT
COMPONENT VIDEO
Y
PB/CB
PR/CR
MONITOR OUT
TV SOUND
VIDEO
S-VIDEO
VIDEO
RIGHT
LEFT
AUDIO
SUBWOOFER
OUT
MONITOR
OUT
AUDIO
RIGHT
DVD
LEFT
VCR
DVD
FRONT
DVD
B
SUB
WOOFER
C
OUT
(REC)
CENTER
VCR
REAR
IN
(PLAY)
RIGHT
A
LEFT
S-VIDEO
VIDEO
D
VIDEO
SUBWOOFER
OUT
TV
Å
ı
Ç
Î
To audio output
To composite video input
To S-video input
To component video input
Å
ı
Ç
Î
To front left/right channel audio output
To composite video output
To S-video output
To component video output
For enjoying DVD MULTI Playback Mode—
• When you connect the DVD player with its analog discrete output
(5.1 CH reproduction) jacks:
DVD player
A
G
DVD
F
E
B
C
D
COMPONENT VIDEO
MONITOR OUT
MONITOR
OUT
AUDIO
RIGHT
LEFT
VCR
DVD
FRONT
DVD
SUB
WOOFER
OUT
(REC)
CENTER
VCR
REAR
RIGHT
IN
(PLAY)
LEFT
S-VIDEO
VIDEO
VIDEO
SUBWOOFER
OUT
Å
ı
Ç
Î
‰
Ï
Ì
To rear left/right channel audio output
To subwoofer audio output
To front left/right channel audio output
To center channel audio output
To composite video output
To S-video output
To component video output
8
EN01-09.RX-7520V[C]f.pm5
8
DVD
02.2.14, 4:31 PM
Y
PB/CB
PR/CR
English
Digital connections
Notes:
This receiver is equipped with two DIGITAL IN terminals—one
digital coaxial terminal and one digital optical terminal.
You can connect any digital component to one of the digital
terminals using a digital coaxial cable (not supplied).
• When shipped from the factory, the DIGITAL IN terminals have
been set for use with the following components:
– DIGITAL 1 (coaxial): For DVD player
– DIGITAL 2 (optical): For CD player
• When you want to operate the CD player or CD recorder using the
COMPU LINK remote control system, connect the target
component also as described in “Analog connections” (see pages 6
and 7).
• When you want to operate the DVD player using the AV COMPU
LINK remote control system, connect the DVD player also as
described in “Analog connections” (see page 8).
IMPORTANT:
• When connecting the DVD player or digital TV using the digital
terminals, you also need to connect it to the video jack on the rear.
Without connecting it to the video jack, you can view no playback
picture.
• After connecting the components using the DIGITAL IN terminals,
set the following correctly if necessary:
– Set the digital input (DIGITAL IN) terminal setting correctly. For
details, see “Setting the Digital Input (DIGITAL IN) Terminals” on
page 14.
– Select the digital input mode correctly. For details, see “Selecting
the Analog or Digital Input Mode” on page 14.
Connecting the Power Cord
Before plugging the receiver into an AC outlet, make sure that all
connections have been made.
Digital input terminals
Plug the power cord into an AC outlet.
Digital TV
DVD player
DVD
CD player
CD recorder
Keep the power cord away from the connecting cables and the
antenna. The power cord may cause noise or screen interference. We
recommend that you use a coaxial cable to connect the antenna,
since it is well-shielded against interference.
Digital coaxial cable (not supplied)
between digital coaxial terminals
CAUTIONS:
• Do not touch the power cord with wet hands.
• Do not pull on the power cord to unplug the cord. When unplugging
the cord, always grasp the plug so as not to damage the cord.
Digital optical cable (not supplied)
between digital optical terminals
When the component has a digital coaxial
output terminal, connect it to the DIGITAL 1
(DVD) terminal with the digital coaxial cable
(not supplied).
When the component has a digital optical
output terminal, connect it to the DIGITAL 2
(CD) terminal, using the digital optical cable
(not supplied).
Before connecting a digital
optical cable, unplug the
protective plug.
DIGITAL 1
(DVD)
DIGITAL 2 ( CD )
DIGITAL IN
9
EN01-09.RX-7520V[C]f.pm5
9
02.2.14, 4:31 PM
English
Basic Operations
Front Panel
Remote Control
Display
STANDBY lamp
RX-7520V AUDIO/VIDEO CONTROL RECEIVER
FM/AM TUNING
FM/AM PRESET
STANDBY/ON
AUDIO
FM MODE
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
STANDBY
MEMORY
SPK 1 2
L
C
R
BASS BOOST
TUNED STEREO
AUTO MUTING SLEEP
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
VOLUME
S.WFR LFE
LS
S
MASTER VOLUME
RS
CH-
STANDBY/ON
SURROUND ON/OFF
INPUT
ANALOG/DIGITAL
BASS BOOST
SLEEP
ADJUST SETTING
DVD MULTI
DVD
PTY–PTY SEARCH–PTY
TV SOUND
VCR
INPUT ATT
SURROUND MODE
1
Source
Selecting
Buttons
CONTROL
DOWN
UP
SPEAKERS ON/OFF
2
CD
TAPE/CDR
AM
FM
SOURCE NAME
PHONES
FM MODE
DIMMER
PHONES
jack
Source SOURCE
Selecting NAME
Buttons
SPEAKERS
ON/OFF
STANDBY/ON
Turning On the Power
Press STANDBY/ON
remote control).
MUTING
VOLUME
+/–
MASTER
VOLUME
Selecting the Source to Play
(or STANDBY/ON
AUDIO on the
STANDBY/ON
Press one of the source selecting buttons. The selected source name
appears on the display.
STANDBY
AUDIO
DVD MULTI
DVD
VCR
TV SOUND
TAPE/CDR
FM
AM
TAPE/CDR
CD
DVD
FM/AM
TV SOUND
VCR
DVD MULTI
STANDBY/ON
On the front panel
From the remote control
The STANDBY lamp goes off. The name of the current source (or
station frequency) appears on the display.
Current source name appears
ANALOG
SPK 1
L
C
S
R
VOLUME
RS
CH-
Current volume level is shown here
To turn off the power (into standby mode)
Press STANDBY/ON
(or STANDBY/ON
AUDIO on the remote
control) again.
The STANDBY lamp lights up.
SOURCE NAME
On the front panel
From the remote control
DVD MULTI
S.WFR LFE
LS
CD
STANDBY
STANDBY/ON
: Select the DVD player for viewing the digital video
disc using the analog discrete output mode (5.1 ch
reproduction).
To enjoy the DVD MULTI playback, see page 30.
DVD
: Select the DVD player.
VCR
: Select the VCR.
TV SOUND : Select the TV sound.
CD *
: Select the CD player.
TAPE/CDR * : Select the cassette deck (or the CD recorder).
FM and AM (FM/AM) *
: Select an FM or AM broadcast.
• Each time you press FM/AM on the remote
control, the band alternates between FM and AM.
Notes:
Note:
A small amount of power is consumed in standby mode. To turn the
power off completely, unplug the AC power cord.
• When connecting a CD recorder (to the TAPE/CDR jacks), change
the source name that appears on the display. See “Changing the
source name” on page 11.
• When you have connected some digital source components using
the digital terminals (see page 9), you need to select the digital
input mode (see page 14).
• When you press one of the source selecting buttons on the remote
control marked above with an asterisk (*), the receiver
automatically turns on.
10
EN10-22.RX-7520V[C]f.pm5
10
02.2.14, 4:31 PM
Remote
NOT
When you connect a CD recorder to the
TAPE/CDR jacks on the rear panel, change the
source name shown on the display.
1 Press TAPE/CDR (SOURCE NAME).
TAPE/CDR
• Make sure “TAPE” appears on the display.
2 Press and hold SOURCE NAME (TAPE/CDR)
until “ASSIGN CDR” appears on the display.
SOURCE NAME
Note:
Without changing the source name, you can still use the connected
component. However, there may be some inconvenience:
– “TAPE” will appear on the display when you select the CD
recorder.
– You cannot use the digital input (see page 14) for the CD recorder.
– You cannot use the COMPU LINK remote control system (see page
31) to operate the CD recorder.
Selecting different sources for picture and sound
You can watch picture from a video component while listening to
sound from another component.
Press one of the audio source selecting buttons—
CD, TAPE/CDR, FM, AM (or FM/AM on the remote control),
while watching the picture from a video component such as the
VCR, or DVD player, etc.
CD
DVD
TAPE/CDR
VCR
TAPE/CDR
CD
DVD
AM
FM/AM
TV SOUND
VCR
SOURCE NAME
On the front panel
On the front panel:
MASTER VOLUME
To increase the volume,
turn MASTER VOLUME clockwise.
To decrease the volume,
turn it counterclockwise.
From the remote control:
To increase the volume, press VOLUME +.
To decrease the volume, press VOLUME –.
VOLUME
CAUTION:
Always set the volume to the minimum before starting any source. If
the volume is set at its high level, the sudden blast of sound energy
can permanently damage your hearing and/or ruin your speakers.
Note:
The volume level can be adjusted within the range of “0” (minimum) to
“50” (maximum).
Selecting the Front Speakers
Remote
NOT
When you have connected two pairs of the front speakers, you can
select which to use.
SPEAKERS ON/OFF
1
2
DVD MULTI
TV SOUND
FM
Adjusting the Volume
TAPE/CDR
SOURCE NAME
To change the source name from “CDR” to “TAPE,” repeat the
same procedure above (in step 1, make sure “CDR” appears on the
display).
DVD MULTI
English
Changing the source name
From the remote control
Notes:
• Once you have selected a video source, pictures of the selected
source are sent to the TV until you select another video source.
• This function can use only when selecting the S-video or composite
video input terminal.
To use the speakers connected to the FRONT SPEAKERS 1
terminals, press SPEAKERS ON/OFF 1 so that the SPK 1 indicator
lights up on the display. (Make sure that the SPK 2 is not lit on the
display.)
To use the speakers connected to the FRONT SPEAKERS 2
terminals, press SPEAKERS ON/OFF 2 so that the SPK 2 indicator
lights up on the display. (Make sure that the SPK 1 is not lit on the
display.)
To use both set of the speakers, press SPEAKERS ON/OFF 1 and
2 so that the SPK 1 and SPK 2 indicators light up on the display.
To use neither set of the speakers, press SPEAKERS ON/OFF
1 and 2 so that the SPK 1 and SPK 2 indicators disappear from the
display.
Notes:
• If you select any of the Surround modes while using both the speakers
connected to the FRONT SPEAKERS 1 and 2 terminals, the
speakers connected to the FRONT SPEAKERS 2 terminals are
deactivated.
• While the Surround mode is in use, you can only select either the
speakers connected to the FRONT SPEAKERS 1 or 2 terminals.
• If you select DVD MULTI as the source while using both the speakers
connected to the FRONT SPEAKERS 1 and 2 terminals, the
speakers connected to the FRONT SPEAKERS 2 terminals are
deactivated.
• When selecting “DVD MULTI” as the source, you can only select
either the speakers connected to the FRONT SPEAKERS 1 or 2
terminals.
11
EN10-22.RX-7520V[C]f.pm5
11
02.2.14, 4:31 PM
English
Basic Operations
Listening Only with Headphones
Changing the Display Brightness
You must turn off both pairs of speakers when you listen with
headphones.
You can dim the display.
1 Connect a pair of headphones to the PHONES jack on the front
Press DIMMER on the remote control.
• Each time you press the button, the display dims and
brightens alternately.
panel.
DIMMER
2 Press SPEAKERS ON/OFF 1 and SPEAKERS ON/OFF 2 so
that neither the SPK 1 nor SPK 2 indicator appears on the
display.
• “HEADPHONE” appears and H. PHONE indicator lights up
on the display.
Turning Off the Power
with the Sleep Timer
ANALOG
L
R
H.PHONE
You can fall asleep while listening to music—Sleep Timer.
This cancels the Surround modes currently selected and activates
the HEADPHONE mode (see below).
HEADPHONE mode
When using the headphones, the following signals are output
regardless of your speaker setting:
— For 2 channel sources, the front left and right channel signals
are output directly from the headphones.
— For multichannel sources, the front left and right, center, and
rear channel signals are down-mixed and then output from the
headphones.
You can enjoy multichannel sound sources using the
headphones.
Notes:
• While in the HEADPHONE mode, you cannot use any Surround
modes (see page 23).
• Activating the speakers cancels the HEADPHONE mode and turns
on the Surround modes previously selected.
CAUTION:
Be sure to turn down the volume:
• Before connecting or putting on headphones, as high volume can
damage both the headphones and your hearing.
• Before turning on speakers again, as high volume may output from
the speakers.
Press SLEEP on the remote control repeatedly.
• The SLEEP indicator lights up on the display and the
shut-off time changes in 10 minutes intervals.
ANALOG
SPK 1
L
C
SLEEP
R
S.WFR LFE
LS
S
RS
CH-
10
20
30
40
50
60
0 (Canceled)
90
80
70
When the shut-off time comes
The receiver turns off automatically.
To check or change the remaining time until the shut-off time
Press SLEEP once.
The remaining time (in minutes) until the shut-off time appears.
• To change the shut-off time, press SLEEP repeatedly until the
preferred remaining time appears on the display.
To cancel the Sleep Timer
Press SLEEP repeatedly until “SLEEP 0 MIN” appears on the
display. (The SLEEP indicator goes off.)
• Turning off the power also cancels the Sleep Timer.
Turning Off the Sounds
Temporarily—Muting
You can turn off the volume temporarily.
Press MUTING on the remote control to mute
the sound through all speakers and headphones
connected.
• “MUTING” appears on the display and the volume turns
off (the volume level indicator goes off).
ANALOG
MUTING
SPK 1
L
C
R
S.WFR LFE
LS
S
RS
CH-
To restore the sound, press MUTING again.
• Turning MASTER VOLUME on the front panel or pressing
VOLUME +/– on the remote control also restores the sound.
12
EN10-22.RX-7520V[C]f.pm5
12
SLEEP
02.2.14, 4:31 PM
English
Basic adjustment auto memory
This receiver memorizes sound settings for each source when—:
• turning off the power,
• changing the source, and
• assigning the source name.
When you change the source, the memorized settings for the
newly selected source are automatically recalled.
The following can be stored for each source:
• Input attenuator mode (see page 19)
• Balance (see page 19)
• Tone adjustment (see page 20)
• Subwoofer output level (see page 20)
• Surround mode selection (see pages 26 – 29)
• Bass boost (see page 20)
Notes:
• You cannot assign and store different settings for digital input
mode and analog input mode.
• If the source is FM or AM, you can assign a different setting for
each band.
For recording
You can record any source through the receiver to —:
• the cassette deck (or CD recorder) connected to the
TAPE/CDR jacks, and
• the VCR connected to the VCR jacks at the same time.
While recording, you can listen to the selected sound source at
whatever sound level you like without affecting the sound levels
of the recording.
Signal and speaker indicators on the display
Speaker indicators
Signal indicators
L
C
R
S.WFR LFE
LS
S
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
RS
SPK 1 2
L
C
R
PRO LOGIC ΙΙ
L
C
R
S.WFR LFE
LS
S
RS
CH-
S.WFR LFE
LS
S
RS
The following signal indicators light up—:
L : •When digital input is selected: Lights up when the left
channel signal comes in.
• When analog input is selected: Always lights up.
R : • When digital input is selected: Lights up when the right
channel signal comes in.
• When analog input is selected: Always lights up.
C : When the center channel signal comes in.
LS : When the left rear channel signal comes in.
RS : When the right rear channel signal comes in.
S : When the monaural rear channel signal or 2 ch Dolby
Surround encoded signal comes in.
LFE: When the LFE channel signal comes in.
The speaker indicators light up when—:
• The corresponding speaker is activated, and
• The corresponding speaker is required for the current playback.
Notes:
• When you select “DVD MULTI,” all the signal indicators except
“S” light up.
• When “SUBWOOFER” is set to “YES” (see page 16), S.WFR
lights up.
Note:
The output volume level, bass boost (see page 20), tone
adjustment (see page 20), and Surround modes (see page 23)
cannot affect the recording.
13
EN10-22.RX-7520V[C]f.pm5
13
02.2.14, 4:31 PM
English
Basic Settings
Front Panel
Remote Control
Display
SETTING
RX-7520V AUDIO/VIDEO CONTROL RECEIVER
FM/AM TUNING
FM/AM PRESET
FM MODE
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
STANDBY
MEMORY
SPK 1 2
L
C
R
BASS BOOST
TUNED STEREO
AUTO MUTING SLEEP
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
VOLUME
S.WFR LFE
LS
S
MASTER VOLUME
RS
CH-
STANDBY/ON
SURROUND ON/OFF
INPUT
ANALOG/DIGITAL
BASS BOOST
ADJUST SETTING
DVD
DVD MULTI
VCR
PTY–PTY SEARCH–PTY
TV SOUND
INPUT ATT
SURROUND MODE
1
Source
Selecting
Buttons
CONTROL
DOWN
UP
SPEAKERS ON/OFF
2
CD
TAPE/CDR
FM
AM
SOURCE NAME
PHONES
INPUT ANALOG/
DIGITAL
Source
Selecting
Buttons
Setting the Digital Input
[DIGITAL IN] Terminals
CONTROL
UP 5/DOWN ∞
Remote
NOT
When you use the digital input terminals, register what components
are connected to which terminals (DIGITAL IN 1/2) so that the correct
source name will appear when you select the digital source.
Before you start, remember....
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
1
Press SETTING repeatedly until
“DIGITAL IN” appears on the display.
ANALOG
/DIGITAL
FM MODE
T SETTING
Then the display changes to show the current setting.
Selecting the Analog or Digital Input
Mode
When you have connected digital source components using both the
analog connections (see page 6) and the digital connections (see
page 9) methods, you need to select the input mode correctly.
Before you start, remember....
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
1
Press one of the source selecting buttons—DVD,
TV SOUND , CD, or TAPE/CDR*—for which
you want to change the input mode.
DIGITAL 2 terminal setting
S.WFR LFE
LS
S
DVD MULTI
RS
DVD
VCR
TV SOUND
TAPE/CDR
FM
AM
TAPE/CDR
CD
DVD
FM/AM
TV SOUND
VCR
DVD MULTI
CHCD
SOURCE NAME
DIGITAL 1 terminal setting
* “1DVD 2CD” is the initial setting. If you have already
changed the setting, another combination will be shown.
2
Press CONTROL UP 5/DOWN ∞ to
select the appropriate digital terminal
setting.
CONTROL
DOWN
UP
• Each time you press the button, the display
changes as follows:
1 DVD 2 CD j 1 DVD 2 TV j
1 CD 2 DVD j 1 CD 2 TV j
1 TV 2 DVD j 1 TV 2 CD j
1 CDR 2 DVD j 1 CDR 2 CD j
(back to the beginning)
On the front panel
Note:
* Among the sources listed above, you can select the digital input
only for the sources which you have selected the digital input
terminals for. (See “Setting the Digital Input (DIGITAL IN)
Terminals” on the left column.)
1 DVD 2 CDR j
1 CD 2 CDR j
1 TV 2 CDR j
1 CDR 2 TV j
Note:
When shipped from the factory, the DIGITAL IN terminals have been
set for use with the following components:
– DIGITAL 1 (coaxial): For DVD player
– DIGITAL 2 (optical): For CD player
14
EN10-22.RX-7520V[C]f.pm5
14
From the remote control
02.2.14, 4:32 PM
Press INPUT ANALOG/DIGITAL
(or ANALOG/DIGITAL on the remote control)
to select the digital input mode.
INPUT
ANALOG / DIGITAL
ANALOG
/DIGITAL
INPUT ATT
On the front panel
2
Press CONTROL UP 5/DOWN ∞ to
select “DOLBY DIGITAL” or “DTS
SURROUND” while “DIGITAL
AUTO” still remains on the display.
• Each time you press the button, the digital input mode changes
as follows:
When “DOLBY DIGITAL” or “DTS SURROUND”
is selected, “DIGITAL AUTO” goes off.
From the remote control
• Each time you press the button, the input mode alternates
between the analog input (“ANALOG”) and the digital input
(“DIGITAL AUTO”).
DIGITAL AUTO : Select this for the digital input mode. The
receiver automatically detects the
incoming signal format. (The DIGITAL
AUTO indicator lights up on the display,
then the digital signal indicator for the
detected signals lights up.)
ANALOG
: Select this for the analog input mode.
(Initial setting when shipped from the
factory.)
If the following symptoms occur while playing Dolby Digital
or DTS Digital Surround software with “DIGITAL AUTO”
selected, follow the procedure below:
• Sound does not come out at the beginning of playback.
• Noise comes out while searching or skipping chapters or
tracks.
1
Press INPUT ANALOG/DIGITAL (or
ANALOG/DIGITAL on the remote control).
INPUT
ANALOG / DIGITAL
ANALOG
/DIGITAL
INPUT ATT
On the front panel
From the remote control
Remote
NOT
SPK
DIGITAL AUTO
L
C
R
S.WFR LFE
DIGITAL
LS
S
RS
CH-
DIGITAL AUTO
DTS SURROUND
DOLBY DIGITAL
• To play back software encoded with Dolby Digital, select
“DOLBY DIGITAL.”
• To play back software encoded with DTS Digital Surround,
select “DTS SURROUND.”
Note:
When you turn off the power or select another source, “DOLBY
DIGITAL” and “DTS SURROUND” are canceled and the digital input
mode is automatically reset to “DIGITAL AUTO.”
The following are the analog/digital signal indicators on the display
to indicate what type of the signal comes into the receiver.
ANALOG
: Lights when the analog input is selected.
LINEAR PCM : Lights when Linear PCM signals come in.
DIGITAL : • Lights when Dolby Digital signals come in.
• Flashes when “DOLBY DIGITAL” is
selected for software not encoded with Dolby
Digital signals.
: • Lights when DTS signals come in.
• Flashes when “DTS SURROUND” is
selected for software not encoded with DTS
signals.
Note:
When “DIGITAL AUTO” cannot recognize the incoming signals, no
digital signal indicators light up on the display.
15
EN10-22.RX-7520V[C]f.pm5
15
02.2.14, 4:32 PM
English
2
English
Basic Settings
Selecting the Video Input
Terminal
Remote
NOT
This receiver is equipped with the component video input terminals
for the DVD player which give you higher picture quality. When you
use the component video input terminals for the DVD player, change
the video input terminal setting.
“NO” for the subwoofer, “LARGE” for the front speakers,
and “SMALL” for the center and rear speakers are initial
settings. To get best possible sound, change the subwoofer
and speaker settings to fit your listening conditions.
Setting the Speaker Information
Remote
NOT
Before you start, remember....
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
To obtain the best possible sound or effect from Surround modes
(see pages 26 to 29), register the following speakers and subwoofer
information after all connections are completed.
1
The following are items you can set:
• Subwoofer information—SUBWOOFER
• Speaker size—FRNT SP, CNTR SP, REAR SP
• Speaker distance—UNIT, FRNT DIS, CNTR DIS, REAR DIS
• Crossover frequency—CROSS
• Low frequency effect attenuator—LFE ATT
• Dynamic range compression—D. COMP
Press SETTING repeatedly until
“VIDEO IN DVD ” or “VIDEO IN
VCR ” appears on the display.
ST SETTING
• Select “VIDEO IN DVD” to select the video input terminal for
the DVD player and “VIDEO IN VCR” for the VCR.
SPK 1
DIGITAL AUTO
LINEAR PCM
L
C
R
CH-
After 2 seconds, the display changes to show the current setting.
2
Press CONTROL UP 5/DOWN ∞
to select the appropriate type of
the video input terminal.
CONTROL
DOWN
UP
• Each time you press the button, the display
changes as follows:
COMPONENT
S/C
(Component)
(S-video/Composite)
Before you start, remember....
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
Subwoofer information
Register whether you have connected a subwoofer or not.
1
Press SETTING repeatedly until
“SUBWOOFER” (with the current
setting)* appears on the display.
ST SETTING
SPK 1
DIGITAL AUTO
LINEAR PCM
L
C
R
S.WFR LFE
CH-
COMPONENT : Select this when you connect the DVD
player or VCR to the component video
input terminals.
S/C
: Select this when you connect the DVD player
or VCR to the S-video or composite video
input terminal.
Note:
Without changing the video input terminal setting, you can see the
picture through the video input terminals, but cannot use the AV
COMPU LINK remote control system correctly (see page 32).
* “NO” is the initial setting. If you have already changed the
setting, “YES” will be shown.
2
Press CONTROL UP 5/DOWN ∞ to
register whether you have connected a
subwoofer or not.
• Each time you press the button, the subwoofer
setting alternates between “YES” and “NO.”
YES
: Select this when you have connected a subwoofer.
You can adjust the subwoofer output level
(see page 20).
NO
: Select this when you have not connected or have
disconnected a subwoofer.
16
EN10-22.RX-7520V[C]f.pm5
16
CONTROL
DOWN
UP
02.2.14, 4:32 PM
Register the sizes of all the connected speakers.
• When you change your speakers, register the information about
the speakers again.
1
L
C
S
DIGITAL AUTO
LINEAR PCM
R
FEET
3
• Each time you press the button, the display
changes as follows:
SMALL
NONE
3
: Select this when you have not connected a speaker.
(Not selectable for the front speakers)
Repeat steps 1 and 2 to select the appropriate
items for other speakers.
CONTROL
DOWN
UP
: Speaker distance is shown in feet.
Press SETTING repeatedly until “FRNT
DIS (Front distance),” “CNTR DIS
(Center distance)” or “REAR DIS (Rear
distance)” (with the current setting)*
appears on the display.
T SETTING
• The display shows the current setting in the unit selected in
step 2.
* “3.0m” is the initial setting for meter and “10FT” is for feet. If
you have already changed the setting, another value will be
shown.
LARGE : Select this when the speaker size is relatively large.
(See “Notes” below.)
NONE
Press CONTROL UP 5/DOWN ∞ to
select the unit.
METER : Speaker distance is shown in meters.
CONTROL
DOWN
UP
SMALL : Select this when the speaker size is relatively small.
(See “Notes” below.)
R
RS
• Each time you press the button, the setting
alternates between “METER” and “FEET.”
* “LARGE” is the initial setting for the front speakers and
“SMALL” is for the center and rear speakers. If you have
already changed the setting, another size will be shown.
LARGE
S
* “METER” is the initial setting. If you have already changed
the setting, “FEET” will be shown.
RS
Press CONTROL UP 5/DOWN ∞ to
select the appropriate item about the
speaker selected in the above step.
C
CH-
CH-
2
L
S.WFR LFE
LS
2
SPK 1
S.WFR LFE
LS
SETTING
SPK 1
Press SETTING repeatedly until “FRNT ST SETTING
SP (Front Speaker),” “CNTR SP (Center
Speaker)” or “REAR SP (Rear Speaker)”
(with the current setting)* appears on the display.
DIGITAL AUTO
LINEAR PCM
Press SETTING repeatedly until “UNIT” T
(with the current setting)* appears on the
display.
4
Press CONTROL UP 5/DOWN ∞ to
select the appropriate speaker distance.
CONTROL
DOWN
UP
• If you select “METER” in step 2, the value is
changed from “0.3m” to “9.0m” by 0.3 m step.
• If you select “FEET” in step 2, the value is
changed from “1FT” to “30FT” by 1 foot step.
Left front
speaker
Notes:
Center speaker
• Keep the following comment in mind as reference when adjusting.
– If the size of the cone speaker unit built in your speaker is greater
than 12 cm (4 3/4 inches), select “LARGE,” and if it is smaller than
12 cm (4 3/4 inches), select “SMALL.”
• If you have selected “NO” for the subwoofer setting, you can only
select “LARGE” for the front speaker setting.
• If you have selected “SMALL” for the front speaker setting, you
cannot select “LARGE” for the center and rear speaker settings.
Right front
speaker
3.0 m
(10 feet)
2.7 m
(9 feet)
2.4 m
(8 feet)
2.1 m
(7 feet)
Left rear
speaker
Speaker distance
Register the unit you use, then the speaker distance from your
listening point.
• If you have set the unit before, start from step 3.
• Speaker distance is not valid for the DVD MULTI playback mode.
Right rear
speaker
Example: In this case,
set “FRNT DIS” to “3.0m” or “10FT,”
set “CNTR DIS” to “2.7m” or “9FT,” and
set “REAR DIS” to “2.4m” or “8FT.”
Note:
If you have selected “NONE” for the center and rear speakers setting,
you cannot set the speaker distance for the center and rear speakers.
17
EN10-22.RX-7520V[C]f.pm5
17
02.2.14, 4:32 PM
English
1
Speaker size
English
Basic Settings
2
Crossover frequency
Small speakers cannot reproduce the bass sounds efficiently. If you
use a small speaker in any position, this receiver automatically
reallocates the bass sound elements assigned from the small speaker
to large speakers.
To use this function properly, set this crossover frequency level
according to the size of the small speaker connected.
• If you have selected “LARGE” for all speakers, this function will
not take effect.
• Crossover frequency is not valid for the DVD MULTI playback
mode and HEADPHONE mode.
Press CONTROL UP 5/DOWN ∞ to
select the low frequency effect
attenuator level.
CONTROL
DOWN
UP
• Each time you press the button, the setting
alternates between “0dB” and “–10dB.”
0dB
–10dB
: Normally select this.
: Select this when the bass sound is distorted.
Dynamic range compression
1
Press SETTING repeatedly until
“CROSS (Crossover)” (with the current
setting)* appears on the display.
ST SETTING
You can compress the dynamic range (difference between maximum
sound and minimum sound) of the reproduced sound. This is useful
when enjoying surround sound at night.
• This function takes effect only when playing back a source
encoded with Dolby Digital.
SPK 1
DIGITAL AUTO
LINEAR PCM
L
C
R
1
S.WFR LFE
LS
RS
S
CH-
* “100HZ” is the initial setting. If you have already changed the
setting, another frequency will be shown.
2
Press CONTROL UP 5/DOWN ∞ to
select the crossover frequency level
you like to use.
CONTROL
DOWN
UP
ANALOG
100HZ
200HZ
CH-
* “MID” is the initial setting. If you have already changed the
setting, another setting will be shown.
120HZ
2
150HZ
Press CONTROL UP 5/DOWN ∞
to select the appropriate compression
level.
ST SETTING
MAX
OFF : Select this when you want to enjoy surround with its
full dynamic range. (No effect applied.)
MID
: Select this when you want to reduce the dynamic range
a little.
MAX : Select this when you want to apply the compression
effect fully. (Useful at night.)
L
C
R
S.WFR LFE
DIGITAL
LS
S
RS
CH-
* “0dB” is the initial setting. If you have already changed the
setting, “–10dB” will be shown.
18
EN10-22.RX-7520V[C]f.pm5
18
MID
OFF
SPK 1
DIGITAL AUTO
CONTROL
DOWN
UP
• Each time you press the button, the
display changes as follows:
If the bass sound is distorted while playing back software using
Dolby Digital or DTS Digital Surround, follow the procedure
below:
• Low frequency effect attenuator is not valid for DVD MULTI
playback mode.
• This function takes effect only when the subwoofer (LFE) signals
come in (with “SUBWOOFER” set to “YES”).
Press SETTING repeatedly until
“LFE ATT (Low Frequency Effect
Attenuator)” (with the current setting)*
appears on the display.
R
S
Low frequency effect attenuator
1
SETTING
SPK 1
L
• Each time you press the button, the crossover
frequency level changes as follows:
80HZ
ST
Press SETTING repeatedly until
“D. COMP (Dynamic range
compression)” (with the current setting)*
appears on the display.
02.2.14, 4:32 PM
English
Sound Adjustments
Front Panel
Remote Control
Display
RX-7520V AUDIO/VIDEO CONTROL RECEIVER
FM/AM TUNING
FM/AM PRESET
FM MODE
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
STANDBY
MEMORY
SPK 1 2
L
C
R
BASS BOOST
TUNED STEREO
AUTO MUTING SLEEP
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
VOLUME
S.WFR LFE
LS
S
MASTER VOLUME
RS
SUBWOOFER
+/–
CH-
STANDBY/ON
SURROUND ON/OFF
INPUT
ANALOG/DIGITAL
BASS BOOST
DVD MULTI
DVD
VCR
TV SOUND
TAPE/CDR
FM
AM
SOUND
INPUT ATT
SURROUND MODE
CONTROL
DOWN
UP
SPEAKERS ON/OFF
1
PTY–PTY SEARCH–PTY
ADJUST SETTING
2
CD
SOURCE NAME
FM MODE
PHONES
INPUT ATT BASS BOOST
ADJUST
CONTROL
UP 5/DOWN ∞
Once each of following settings has been adjusted, this receiver
memorizes the adjustment for each source.
Attenuating the Input Signal
Remote
NOT
When the input level of the analog source is too high, the sounds
will be distorted. If this happens, you need to attenuate the input
signal level to prevent the sound distortion.
1
Press and hold INPUT ATT
(INPUT ANALOG/DIGITAL) so
that the INPUT ATT indicator lights
up on the display.
ANALOG
BASS
BOOST
INPUT
ANALOG / DIGITAL
INPUT ATT
Adjusting the Front Speakers
Output Balance
Remote
NOT
If the sounds you hear from the front right and left speakers are
unequal, you can adjust the speakers output balance.
Before you start, remember....
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
1
Press ADJUST repeatedly until
“BALANCE” (with the current setting)*
appears on the display.
ADJUST SETTING
SPK 1
L
C
R
SPK 1
INPUT ATT
DIGITAL AUTO
LINEAR PCM
S.WFR LFE
LS
S
RS
L
C
R
S.WFR LFE
LS
CH-
S
RS
CH-
• Each time you press and hold the button, the Input Attenuator
mode turns on (“INPUT ATT ON”) or off (“INPUT
NORMAL”).
* “CNTR (Center)” is the initial setting. If you have already
changed the setting, another setting will be shown.
2
Note:
When selecting “DVD MULTI” as the source, this effect does not work.
Press CONTROL UP 5/DOWN ∞
to adjust the balance.
CONTROL
DOWN
UP
• Pressing CONTROL UP 5 decreases the
left channel output from “CNTR” (Center)
to “L–21.”
• Pressing CONTROL DOWN ∞ decreases
the right channel output from “CNTR” (Center) to “R–21.”
19
EN10-22.RX-7520V[C]f.pm5
19
02.2.14, 4:32 PM
English
Sound Adjustments
Remote
NOT
Adjusting the Tone
You can adjust the bass and treble sounds as you like.
You can adjust the subwoofer output level if you have connected a
subwoofer and set the subwoofer information correctly—“YES.”
Before you start, remember....
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
1
Adjusting the Subwoofer Output Level
Press ADJUST repeatedly until “BASS”
or “TREBLE” (with the current setting)*
appears on the display.
ADJUST SETTIN
On the front panel:
Before you start, remember....
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
1
SPK 1
DIGITAL AUTO
LINEAR PCM
L
C
Press ADJUST repeatedly until
“SUBWFR” (with the current setting)*
appears on the display.
R
S.WFR LFE
LS
S
RS
CH-
SPK 1
DIGITAL AUTO
LINEAR PCM
L
* “0” is the initial setting. If you have already changed the
setting, another number (level) will be shown.
• Each time you press the button, the sound
level changes by ±2 steps.
R
RS
CH-
: To adjust the bass.
Press CONTROL UP 5/DOWN ∞ to
adjust the bass or treble sounds level
(–10 to +10).
S
* “0” is the initial setting. If you have already changed the
setting, another number (level) will be shown.
2
TREBLE : To adjust the treble.
2
C
S.WFR LFE
LS
BASS
ADJUST SETTING
CONTROL
DOWN
UP
Press CONTROL UP 5/DOWN ∞ to
adjust the subwoofer output level
(–10 to +10).
CONTROL
DOWN
UP
From the remote control:
1
Press SOUND.
SOUND
The 10 keys are activated for sound adjustments.
2
Press SUBWOOFER +/– to adjust
the subwoofer output level
(–10 to +10).
SUBWOOFER
0
10
100
Note:
Subwoofer output level cannot be adjusted when using headphones.
Reinforcing the Bass
You can boost the bass level.
Press BASS BOOST to select the bass boost
function.
BASS BOOST
On the front panel
BASS BOOST
From the remote control
• Each time you press the button, the bass boost function turns
on (“BASSBOOST ON”) and off (“BASSBOOST OFF”).
– Select “BASSBOOST ON” to activate the bass boost function.
The BASS BOOST indicator lights up on the display.
– Select “BASSBOOST OFF” to cancel it.
The indicator goes off.
Note:
This function affects the front speaker sounds only.
20
EN10-22.RX-7520V[C]f.pm5
20
02.2.14, 4:32 PM
English
Tuner Operations
Front Panel
Remote Control
FM/AM FM/AM
TUNING PRESET
5/∞
5/∞
FM MODE
Display
10 keys
RX-7520V AUDIO/VIDEO CONTROL RECEIVER
FM/AM TUNING
FM/AM PRESET
PTY–PTY SEARCH–PTY
FM MODE
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
STANDBY
MEMORY
SPK 1 2
L
C
R
BASS BOOST
TUNED STEREO
AUTO MUTING SLEEP
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
VOLUME
S.WFR LFE
LS
S
MASTER VOLUME
RS
CH-
STANDBY/ON
SURROUND ON/OFF
INPUT
ANALOG/DIGITAL
BASS BOOST
FM/AM
FM MODE
ADJUST SETTING
DVD
DVD MULTI
VCR
TV SOUND
INPUT ATT
SOURCE NAME
SURROUND MODE
1
FM MODE
CONTROL
DOWN
UP
SPEAKERS ON/OFF
2
CD
TAPE/CDR
FM
AM
SOURCE NAME
PHONES
MEMORY
FM, AM
Using Preset Tuning
Tuning in Stations Manually
1
Press FM or AM (FM/AM).
The last received station of the selected band is tuned in.
FM
AM
On the front panel
To store the preset stations
FM/AM
Remote
NOT
From the remote control
• Each time you press the button on the remote control (FM/
AM), the band alternates between FM and AM.
ANALOG
TUNED STEREO
SPK 1
L
C
Once a station is assigned to a channel number, the station can be
quickly tuned. You can preset up to 30 FM and 15 AM stations.
Before you start, remember....
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 2 again.
1
AUTO MUTING
R
VOLUME
If you want to store the FM reception mode for this station,
select the FM reception mode you want. See “Selecting the FM
Reception Mode” on page 22.
S.WFR LFE
LS
S
Tune in the station you want to preset
(see “Tuning in Stations Manually”).
RS
CH-
Ex.: When the FM band is selected
ANALOG
L
2
Press FM/AM TUNING 5/∞
repeatedly until you find the
frequency you want.
• Pressing FM/AM TUNING 5 increases the
frequency.
• Pressing FM/AM TUNING ∞ decreases the
frequency.
TUNED STEREO
SPK 1
C
AUTO MUTING
R
VOLUME
S.WFR LFE
LS
Remote
NOT
FM/AM TUNING
RS
S
CH-
2
Press MEMORY.
MEMORY
The CH- indicator lights up and the channel number
position starts flashing on the display for about 5
seconds.
ANALOG
TUNED STEREO
SPK 1
L
Notes:
C
AUTO MUTING
R
VOLUME
S.WFR LFE
LS
• When you hold FM/AM TUNING 5/∞ in step 2, the frequency
keeps changing until a station is tuned in.
• When a station of sufficient signal strength is tuned in, the TUNED
indicator lights up on the display.
• When an FM stereo program is received, the STEREO indicator
also lights up.
RS
S
CH-
3
Press FM/AM PRESET 5/∞ to
select a channel number while the
channel number position is
flashing.
ANALOG
TUNED STEREO
SPK 1
L
C
R
FM/AM PRESET
AUTO MUTING
VOLUME
S.WFR LFE
LS
S
RS
CH-
21
EN10-22.RX-7520V[C]f.pm5
21
02.2.14, 4:32 PM
English
Tuner Operations
4
Press MEMORY again while the
selected channel number is flashing
on the display.
Selecting the FM Reception Mode
MEMORY
When an FM stereo broadcast is hard to receive or noisy, you can
change the FM reception mode while receiving an FM broadcast.
• You can store the FM reception mode for each preset station. (See
page 21).
The selected channel number stops flashing.
The station is assigned to the selected channel number.
ANALOG
TUNED STEREO
SPK 1
L
C
AUTO MUTING
R
VOLUME
1
S.WFR LFE
LS
RS
S
CH-
5
Repeat steps 1 to 4 until you store all the stations
you want.
While listening to an FM station, press
FM MODE.
• Each time you press the button, the FM reception mode
alternates between “AUTO*” and “MONO.”
FM MODE
FM MODE
To erase a stored preset station
Storing a new station on a used number erases the previously stored
one.
On the front panel
ANALOG
1
TUNED STEREO
SPK 1
L
To tune in a preset station
On the front panel:
From the remote control
C
AUTO MUTING
R
S.WFR LFE
LS
RS
S
CH-
Press FM or AM.
FM
AM
The last received station of the selected
band is tuned in.
ANALOG
TUNED
SPK 1
L
C
R
S.WFR LFE
LS
ANALOG
TUNED STEREO
SPK 1
L
C
AUTO MUTING
R
S
RS
CH-
VOLUME
S.WFR LFE
LS
S
RS
CH-
2
* “AUTO” is the initial setting.
Press FM/AM PRESET 5/∞
repeatedly until you find the channel
you want.
FM/AM PRESET
• Pressing FM/AM PRESET 5 increases
the channel numbers.
• Pressing FM/AM PRESET ∞ decreases the channel numbers.
From the remote control:
1
Press FM/AM to select the band
—FM or AM.
FM/AM
AUTO
: Normally select this.
When a program is broadcasted in stereo, you will
hear stereo sound; when in monaural, you will
hear monaural sounds. This mode is also useful to
suppress static noise between stations. The AUTO
MUTING indicator lights up on the display.
MONO
: Select this to improve the reception (but stereo
effect will be lost).
In this mode, you will hear noise while tuning into
the stations. The AUTO MUTING indicator goes
off from the display. (The STEREO indicator also
goes off.)
The last received station of the selected band is tuned
in and the10 keys now work for tuner operation.
• Each time you press the button, the band alternates between
FM and AM.
2
Press 10 keys to select a preset
channel number.
•
•
•
•
For channel number 5, press 5.
For channel number 15, press +10 then 5.
For channel number 20, press +10 then 10.
For channel number 30, press +10, +10,
then 10.
TEST
1
CENTER
EFFECT
4
REAR L
7/P
10
6
5
REAR R
MENU
ENTER
3
2
8
9
SUBWOOFER
0
RETURN
10
100
Note:
When you use 10 keys on the remote control, be sure that they are
activated for the tuner, not for the CD and others. (See page 34).
22
EN10-22.RX-7520V[C]f.pm5
22
02.2.14, 4:32 PM
You can use the following Surround modes to reproduce a realistic
sound field:
■ Dolby Surround
• Dolby Pro Logic II
• Dolby Digital
■ DTS Digital Surround
■ DAP modes
■ All Channel Stereo
■ Dolby Surround
Dolby Pro Logic II*
English
Creating Realistic Sound Fields
Dolby Digital*
Used to reproduce multichannel sound tracks of the software
).
encoded with Dolby Digital (
• To enjoy the software encoded with Dolby Digital, connect the
source component using the digital terminal on the rear of this
receiver. (See page 9.)
D I G I T A L
Dolby Digital 5.1 ch encoding method (so-called discrete
multichannel digital audio format) records and digitally compresses
the left front channel, right front channel, center channel, left rear
channel, right rear channel, and LFE channel signals.
Since each channel is completely independent from the other
channel signals to avoid interference, you can obtain much better
sound quality with much stereo and surround effect.
Dolby Pro Logic II has a newly developed multichannel playback
format to decode all 2 channel sources—stereo source and Dolby
Surround encoded source—into 5.1 channel.
Matrix-based encoding/decoding method for Dolby Pro Logic II
makes no limitation for the cutoff frequency of the rear treble and
enables stereo rear sound compared to conventional Dolby Pro
Logic.
Dolby Digital software can be roughly grouped into two categories
—multichannel (up to “5.1” ch) and 2 channel software. To enjoy
surround sounds while playing Dolby Digital 2 ch software, you can
use Dolby Pro Logic II.
Dolby Pro Logic II enables to reproduce spacious sound from
original sound without adding any new sounds and tonal colorations.
Dolby Pro Logic II has two modes—Movie mode and Music mode:
■ DTS Digital Surround**
Pro Logic II Movie (PL II MOVIE)—suitable for reproduction of
DOLBY SURROUND .
Dolby Surround encoded sources bearing the mark
You can enjoy soundfield very close to the one created with discrete
5.1 channel sounds.
Pro Logic II Music (PL II MUSIC)—suitable for reproduction of
any 2 channel stereo music sources. You can enjoy wide and deep
sound by using this mode. For this mode, Panorama control can be
selected, which gives “wraparound” sound effect with side-wall
image.
• When Dolby Pro Logic II is activated, the
indicator lights up on the display.
PRO LOGIC II
Note:
Used to reproduce multichannel sound tracks of the software
encoded with DTS Digital Surround (
).
• To enjoy the software encoded with DTS Digital Surround,
connect the source component using the digital terminal on the
rear of this receiver. (See page 9.)
DTS Digital Surround is another discrete multichannel digital
audio format available on CD, LD, and DVD software.
Compared to Dolby Digital, audio compression ratio is relatively
low. This fact allows DTS Digital Surround format to add breadth
and depth to the reproduced sounds. As a result, DTS Digital
Surround features natural, solid and clear sound.
Typical Multichannel (5.1 ch) reproduction
Center
speaker
Subwoofer Right front
speaker
Left front
speaker
STANDBY
STANDBY ON
DOLBY
D I G I T A L
RX-7020V AUDIO/VIDEO CONTROL RECEIVER
FM/AM TUNING
FM/AM PRESET
FM MODE
STANDBY
MASTER VOLUME
COMPULINK
Remote
MEMORY
D I G I T A L
SURROUND
SURROUND ON/OFF
INPUT
ANALOG/DIGITAL
BASS BOOST
ADJUST SETTING
DVD MULTI
DVD
VCR
TAPE/CDR
PHONO
TV SOUND/DBS
INPUT ATT
SOURCE NAME
SURROUND MODE
CONTROL
DOWN
UP
SPEAKERS ON/OFF
1
2
CD
FM/AM
SOURCE NAME
PHONES
Left rear
speaker
* Manufactured under license from Dolby Laboratories. “Dolby,” “Pro
Logic,” and the double-D symbol are trademarks of Dolby
Laboratories. Confidential unpublished works. ©1992–1997 Dolby
Laboratories, Inc. All rights reserved.
Right rear
speaker
** Manufactured underlicense from Digital Theater Systems, Inc. US
PAT. No. 5,451,942 and other world-wide patents issued and
pending. “DTS” and “DTS Digital Surround” are trademarks of
Digital Theater Systems, Inc. Copyright 1996 Digital Theater
Systems, Inc. All rights reserved.
23
EN23-29.RX-7520V[C]f.pm5
23
02.2.14, 4:32 PM
English
Creating Realistic Sound Fields
■ DAP (Digital Acoustic Processor) modes
■ All Channel Stereo
DAP modes have been designed to create important acoustic
surround elements.
This mode can reproduce a larger stereo sound field using all the
connected (and activated) speakers.
The sound heard in a live club, dance club, hall or pavilion consists
of direct sound and indirect sound—early reflections and reflections
from behind. Direct sounds reach the listener directly without any
reflection. On the other hand, indirect sounds are delayed by the
distances of the ceiling and walls (see the diagram below).
These indirect sounds are important elements of the acoustic
surround effects. The DAP mode can reproduce a realistic sound
field by adding these indirect sounds.
All Channel Stereo can be used when the front and rear
speakers are connected to this receiver without respect to the
center speaker connection.
If the center speaker is connected and activated, the same phase of
the front left and right signals are output through the center speaker.
DAP modes can be used when the front and rear speakers are
connected to this receiver (without respect to the center speaker
connection: no sound comes out of the center speaker even if it is
connected).
All Channel Stereo can be used while reproducing 2 channel stereo
software, either analog or digital except Dolby Digital and DTS
Digital Surround.
• When All Channel Stereo is selected, the DSP indicator lights up
on the display.
All Channel Stereo reproduction
The following DAP modes are provided with this receiver:
LIVE CLUB
: Gives the feeling of a live music club with a low
ceiling.
DANCE CLUB : Gives a throbbing bass beat.
HALL
: Gives clear vocal and the feeling of a concert
hall.
PAVILION
: Gives the spacious feeling of a pavilion with a
high ceiling.
These DAP modes can be used to add the acoustic surround effects
while reproducing 2 channel stereo software—either analog or
digital except Dolby Digital and DTS Digital Surround—and can
give you a real “being there” feeling.
• When one of the DAP modes is selected, the DSP indicator lights
up on the display.
Sound reproduced from All Channel Stereo
DVD MULTI Playback Mode
Creating sound field
This receiver provides the DVD MULTI playback mode for
reproducing the analog discrete 5.1 channel output mode of the
DVD player or other equipment.
You can adjust speaker output levels while playing back a video
software such as a DVD using the analog discrete 5.1 channel
output mode.
• For connecting analog discrete output jacks, see page 8.
• For details on the DVD MULTI playback mode, see page 30.
Reflections from behind
Early reflections
Note:
When you select “DVD MULTI” as the source to play, Surround mode
is canceled, and the SURROUND ON/OFF and SURROUND MODE
buttons do not work.
Direct sounds
䡬: Possible / ⳯: Impossible
Available Surround modes for each input signal
Mode SURROUND
Signals
OFF (stereo)
DOLBY
DIGITAL
DTS
SURROUND
PLII
MOVIE
PLII
MUSIC
LIVE
CLUB
DANCE
CLUB
HALL
PAVILION
ALL CH
STEREO
Dolby Digital
(Multichannel)
䡬
䡬
⳯
⳯
⳯
⳯
⳯
⳯
⳯
⳯
Dolby Digital
(2 channel)
䡬
⳯
⳯
䡬
䡬
⳯
⳯
⳯
⳯
⳯
DTS Digital
Surround
(Multichannel)
䡬
⳯
䡬
⳯
⳯
⳯
⳯
⳯
⳯
⳯
DTS Digital
Surround
(2 channel)
䡬
⳯
⳯
䡬
䡬
⳯
⳯
⳯
⳯
⳯
Linear PCM
䡬
⳯
⳯
䡬
䡬
䡬
䡬
䡬
䡬
䡬
Analog
䡬
⳯
⳯
䡬
䡬
䡬
䡬
䡬
䡬
䡬
24
EN23-29.RX-7520V[C]f.pm5
24
02.2.14, 4:32 PM
English
About Relations between Speaker Layouts and Surround Modes
Available Surround modes will vary depending on how many speakers are used with this receiver.
Make sure that you have set the speaker information correctly (see pages 16 to 18).
• If only front speakers are connected, you cannot use Surround modes.
• If rear speakers are not connected, you cannot use DAP modes and All Channel Stereo.
Speaker Layouts
Available Surround modes
When the center and rear speakers
are connected (5 channels):
Turning on or off the Surround modes
Each time you press SURROUND ON/OFF, Surround modes turn on or off.
SURROUND ON/OFF
Front
speaker
TV
Front
speaker
Center speaker
TUNED STEREO
SPK 1
L
DIGITAL AUTO
LINEAR PCM
C
AUTO MUTING
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
R
S.WFR LFE
LS
ON/OFF
S
RS
SURROUND
(Remote)
(Front panel)
Last selected
Surround mode
SURROUND OFF
Ex.: “PL II MUSIC” has been selected.
Rear
speaker
Rear
speaker
Selecting the Surround modes
Each time you press SURROUND MODE, Surround modes change as follows:
SURROUND
When the rear speakers are connected
(4 channels):
(Remote)
Front
speaker
TV
SURROUND MODE
L
C
S
VOLUME
RS
PL II MOVIE
LIVE CLUB
HALL
ALL CH STEREO
Front
speaker
AUTO MUTING
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
R
S.WFR LFE
LS
(Front panel)
TUNED STEREO
SPK 1
DIGITAL AUTO
LINEAR PCM
MODE
PL II MUSIC
DANCE CLUB
PAVILION
(Back to the beginning)
Note:
Rear
speaker
Rear
speaker
When the center speaker is connected
(3 channels):
When the digital multichannel software such as Dolby Digital or DTS Digital
Surround is played back, the appropriate multichannel Surround mode is activated
(“DOLBY DIGITAL” or “DTS SURROUND”) by pressing SURROUND ON/OFF (with
the digital input mode selected).
• For Dolby Digital 2 ch software, you need to select “PLII MUSIC” or “PLII MOVIE”
by pressing SURROUND MODE.
• For more details, see the table on page 24.
Turning on or off the Surround modes
Each time you press SURROUND ON/OFF, the Surround modes turn on or off.
SURROUND ON/OFF
Front
speaker
TV
Center speaker
Front
speaker
TUNED STEREO
SPK 1
DIGITAL AUTO
LINEAR PCM
L
C
R
AUTO MUTING
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
S.WFR LFE
LS
ON/OFF
S
RS
SURROUND
(Remote)
(Front panel)
PL II MOVIE
or
PL II MUSIC
SURROUND OFF
Ex.: “PL II MUSIC” has been selected.
Selecting the Surround modes
Each time you press SURROUND MODE, Surround modes change as follows:
SURROUND
SURROUND MODE
L
(Front panel)
C
R
AUTO MUTING
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
S.WFR LFE
LS
(Remote)
TUNED STEREO
SPK 1
DIGITAL AUTO
LINEAR PCM
MODE
S
RS
PL II MOVIE
PL II MUSIC
Note:
When the digital multichannel software such as Dolby Digital or DTS Digital
Surround is played back, the appropriate multichannel Surround mode is activated
(“DOLBY DIGITAL” or “DTS SURROUND”) by pressing SURROUND ON/OFF (with
the digital input mode selected).
• For Dolby Digital 2 ch software, you need to select “PLII MUSIC” or “PLII MOVIE”
by pressing SURROUND MODE.
• For more details, see the table on page 24.
25
EN23-29.RX-7520V[C]f.pm5
25
02.2.14, 4:32 PM
English
Creating Realistic Sound Fields
Before you start, remember....
• Make sure that you have set the speaker information correctly (see pages 16 to 18).
• You cannot adjust the center speaker output level when you have set “CNTR SP” to “NONE.”
• You cannot adjust the rear speaker output levels when you have set “REAR SP” to “NONE.”
• Remember not to change the speaker setting while using any Surround modes; otherwise, it may be canceled when you deactivate the
speakers required for the Surround mode.
Front Panel
Display
RX-7520V AUDIO/VIDEO CONTROL RECEIVER
FM/AM TUNING
FM/AM PRESET
FM MODE
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
STANDBY
MEMORY
SPK 1 2
L
C
R
BASS BOOST
TUNED STEREO
AUTO MUTING SLEEP
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
VOLUME
S.WFR LFE
LS
S
MASTER VOLUME
RS
CH-
STANDBY/ON
SURROUND ON/OFF
INPUT
ANALOG/DIGITAL
BASS BOOST
ADJUST SETTING
DVD
VCR
TV SOUND
TAPE/CDR
FM
AM
DVD MULTI
INPUT ATT
SURROUND MODE
CONTROL
DOWN
UP
SPEAKERS ON/OFF
1
2
CD
SOURCE NAME
PHONES
SURROUND SURROUND
MODE
ON/OFF
ADJUST
CONTROL
UP 5/DOWN ∞
Using Dolby Pro Logic II, Dolby Digital
and DTS Digital Surround
Remote Control
Once you have adjusted the Surround modes, the adjustment is
memorized for each source.
• When playing back digital multichannel software (Dolby Digital
5.1 ch or DTS Digital Surround), the SURROUND MODE button
does not work.
CENTER +/–
TEST
From the remote control:
EFFECT
REAR•L +/–
REAR•R +/–
SOUND
It will be convenient for you to use the remote control for
adjustments, since you can make adjustments from your listening
point, by using the test signal.
• For selecting Panorama mode for Pro Logic II Music, use the
button on the front panel.
PTY–PTY SEARCH–PTY
1
Set the analog or digital input mode for the
source you like to listen and start playing.
When playing back software encoded with Dolby Digital and DTS
Digital Surround, select the digital input mode (see page 14).
FM MODE
SURROUND
ON/OFF
SURROUND
MODE
2
Press SURROUND ON/OFF to
activate Surround mode.
Each time you press the button, Surround mode
turns on and off alternately.
• If you are playing back software encoded with Dolby Digital
multichannel, “DOLBY DIGITAL” is selected.
• If you are playing back software encoded with DTS Digital
Surround, “DTS SURROUND” is selected.
SURROUND
• If you are playing back any software other
MODE
than above, you can select “PL II MUSIC” or
“PL II MOVIE” according to the source by
pressing SURROUND MODE. ( PRO LOGIC
II indicator lights up on the display.)
If you like to adjust sound, go to step 3.
26
EN23-29.RX-7520V[C]f.pm5
26
ON/OFF
SURROUND
02.2.14, 4:32 PM
Press SOUND.
SOUND
Press TEST to check if you can hear the
sounds through all the speakers at the
equal level.
On the front panel:
You can also use the buttons on the front panel to adjust the
Surround modes. However, no test tone is available when using the
buttons on the front panel. So make adjustments while listening to
the sound of the source played back.
The 10 keys are activated for sound adjustments.
4
TEST
1
1
“TEST TONE L” starts flashing on the display and a test tone
comes out of the speakers in the following order:
TEST TONE L
TEST TONE C
TEST TONE R
(Left front speaker)
(Center speaker)
(Right front speaker)
TEST TONE LS
TEST TONE RS
(Left rear speaker)
(Right rear speaker)
2
Adjust the speaker output levels (–10 to +10).
Adjust the center speaker and rear speakers levels comparing to
the sound from the front speakers.
• To adjust the left rear speaker level, press
REAR•L +/–.
• To adjust the right rear speaker level, press
REAR•R +/–.
6
Press TEST again to stop the test
tone.
Press SURROUND ON/OFF to
activate Surround mode.
SURROUND ON/OFF
Each time you press the button, Surround mode
turns on and off alternately.
• If you are playing back software encoded with Dolby Digital
multichannel, “DOLBY DIGITAL” is selected.
• If you are playing back software encoded with DTS Digital
Surround, “DTS SURROUND” is selected.
SURROUND MODE
• If you are playing back any software other
than above, you can select “PL II MUSIC” or
“PL II MOVIE” according to the source by
pressing SURROUND MODE. ( PRO
LOGIC II indicator lights up on the display.)
• You can adjust the speaker output levels without outputting the
test tone.
• No test tone comes out of the center speaker when “CNTR SP”
is set to “NONE.”
• No test tone comes out of the rear speakers when “REAR SP”
is set to “NONE.”
• To adjust the center speaker level, press
CENTER +/–.
Set the analog or digital input mode for the
source you like to hear and start playing.
When playing back software encoded with Dolby Digital and DTS
Digital Surround, select the digital input mode (see page 14).
Notes:
5
English
3
If you like to adjust sound, go to step 3.
CENTER
3
2
REAR L
5
6
REAR R
9
8
3
Adjust the speaker output levels.
1) Press ADJUST repeatedly until one
of the following indications (with the
current setting)* appears on the
display.
ADJUST SETTING
SPK 1
DIGITAL AUTO
LINEAR PCM
L
C
R
PRO LOGIC ΙΙ
S.WFR LFE
LS
S
RS
CH-
* “0” is the initial setting. If you have already changed the
setting, another number (level) will be shown.
TEST
1
CENTER : To adjust the center speaker output level
(–10 to +10).
REAR L : To adjust the left rear speaker output level
(–10 to +10).
REAR R : To adjust the right rear speaker output level
(–10 to +10).
2) Press CONTROL UP 5/DOWN ∞
to adjust the selected speaker
output levels.
CONTROL
DOWN
UP
3) Repeat steps 1) and 2) to adjust the other
speaker levels.
27
EN23-29.RX-7520V[C]f.pm5
27
02.2.14, 4:33 PM
English
Creating Realistic Sound Fields
When you select “PL II MUSIC,” you can go to the
following adjustment.
Remote
NOT
4
Turn Panorama control on or off.
1) Press ADJUST repeatedly until
“PANORAMA” (with the current
setting)* appears on the display.
ADJUST SETTING
L
C
R
Once you have adjusted the DAP modes and All Channel Stereo, the
adjustment is memorized for each source.
• You cannot use the DAP modes and All Channel Stereo if no rear
speakers are connected.
• You cannot adjust the effect level for “ALL CH STEREO.”
From the remote control:
It will be convenient for you to use the remote control for
adjustments, since you can make adjustments from your listening
point.
SPK 1
DIGITAL AUTO
LINEAR PCM
Using DAP Modes and All Channel Stereo
PRO LOGIC ΙΙ
S.WFR LFE
LS
S
RS
CH-
* “OFF” is the initial setting. If you have already changed
the setting, “ON” will be shown.
2) Press CONTROL UP 5/DOWN ∞
to turn on or off Panorama control.
1
Start playing 2 channel software—either analog
or Linear PCM—and select the source.
2
Press SURROUND ON/OFF to activate
Surround mode.
CONTROL
DOWN
UP
When the Surround mode turns on, the last selected
Surround mode will be activated.
• Each time you press the button, Surround mode turns on and
off alternately.
• Each time you press the button, “ON” and
“OFF” change alternately.
ON
OFF
: Select this when you like to enjoy
“wraparound” sound effect with side-wall
image.
ON/OFF
SURROUND
3
: Select this when you like to enjoy
originally recorded sounds.
Press SURROUND MODE repeatedly
until one of the DAP modes—“LIVE
CLUB,” “DANCE CLUB,” “HALL”
and “PAVILION”—or “ALL CH
STEREO” appears on the display.
SURROUND
MODE
The DSP indicator also lights up on the display.
If you like to adjust sound, go to step 4.
To cancel Surround mode
Press SURROUND ON/OFF again so that “SURROUND OFF”
appears on the display.
• If Surround mode is canceled while playing back multichannel
digital software, all channel signals are mixed and output through
the front speakers (and subwoofer if you have connected a
subwoofer and set the subwoofer setting correctly—“YES”).
4
Press SOUND.
SOUND
The 10 keys are activated for sound adjustments.
5
Adjust the speakers output levels
(–10 to +10).
5
• To adjust the right rear speaker level, press
REAR•R +/–.
8
For “ALL CH STEREO” only:
• To adjust the center speaker level, press
CENTER +/–.
6
REAR L
• To adjust the left rear speaker level, press
REAR•L +/–.
6
REAR R
9
CENTER
3
2
For DAP modes only:
Press EFFECT to select the effect
level (1 to 5) you want.
EFFECT
4
• Each time you press the button, the effect
level changes as follows:
EFFECT 1
EFFECT 2
EFFECT 5
EFFECT 3
EFFECT 4
As the number increases, the selected mode becomes stronger
(normally set it to “EFFECT 3”).
28
EN23-29.RX-7520V[C]f.pm5
28
02.2.14, 4:33 PM
1
Start playing 2 channel software—either analog
or Linear PCM—and select the source.
2
Press SURROUND ON/OFF to
activate Surround mode.
SURROUND ON/OFF
When Surround mode turns on, the last selected
Surround mode will be activated.
• Each time you press the button, Surround mode
turns on and off alternately.
3
For DAP modes only: Adjust the effect level.
1) Press ADJUST repeatedly until
“EFFECT” (with the current
setting)* appears on the display.
ADJUST SETTING
* “EFFECT 3” is the initial setting. If you have already
changed the setting, another setting will be shown.
2) Press CONTROL UP 5/DOWN ∞
to select the effect
level (1 to 5) you want.
Press SURROUND MODE repeatedly SURROUND MODE
until one of the DAP modes—“LIVE
CLUB,” “DANCE CLUB,” “HALL”
and “PAVILION”—or “ALL CH STEREO”
appears on the display.
The DSP indicator also lights up on the display.
English
5
On the front panel:
CONTROL
DOWN
UP
• Each time you press the button, the effect
level changes as follows:
EFFECT 1
EFFECT 5
EFFECT 2
EFFECT 3
EFFECT 4
As the number increases, the selected mode becomes
stronger (normally set it to “EFFECT 3”).
If you like to adjust sound, go to step 4.
4
To cancel DAP modes and All Channel Stereo
Adjust the speaker output levels.
1) Press ADJUST repeatedly until one
of the following indications (with the
current setting)* appears on the
display.
ADJUST SETTIN
Press SURROUND ON/OFF again so that “SURROUND OFF”
appears on the display. The DSP indicator goes off.
REAR L : To adjust the left rear speaker output level
(–10 to +10).
REAR R : To adjust the right rear speaker output level
(–10 to +10).
CENTER : For “ALL CH STEREO” only—to adjust the
center speaker output level
(–10 to +10).
* “0” is the initial setting. If you have already changed the
setting, another number (level) will be shown.
2) Press CONTROL UP 5/DOWN ∞
to adjust the selected speaker
output levels.
CONTROL
DOWN
UP
3) Repeat steps 1) and 2) to adjust the other
speaker levels.
29
EN23-29.RX-7520V[C]f.pm5
29
02.2.14, 4:33 PM
English
Using DVD MULTI Playback Mode
This receiver provides the DVD MULTI playback mode for
reproducing the analog discrete output mode of the DVD player.
Before playing back a DVD, refer also to the manual supplied with
the DVD player.
From the remote control:
1
When you select “DVD MULTI” as the source to play, Surround
mode is canceled, and the SURROUND ON/OFF and
SURROUND MODE buttons do not work.
2
If you need to make any adjustments, go to the
following steps.
3
On the front panel:
4
Press DVD MULTI.
DVD MULTI
Notes:
• When you select “DVD MULTI” as the source to play, the
Surround mode is canceled, and the SURROUND ON/OFF and
SURROUND MODE buttons do not work.
• If you select DVD MULTI as the source while using both the
speakers connected to the FRONT SPEAKERS 1 and 2
terminals, the speakers connected to the FRONT SPEAKERS
2 terminals are deactivated.
• When selecting “DVD MULTI” as the source, you can only
select either the speakers connected to the FRONT
SPEAKERS 1 or 2 terminals.
2
Select the analog discrete output mode on the
DVD player, and start playing a DVD.
• Refer also to the manual supplied with the DVD player.
Before you start, remember....
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
1
Press SOUND.
Adjust the speaker output levels.
• To adjust the center speaker level, press
CENTER +/– (–10 to +10).
5
• To adjust the right rear speaker level, press
REAR•R +/– (–10 to +10).
8
If you need to make any adjustments, go to the
following steps.
ADJUST SETTING
CENTER :To adjust the center speaker output level
(–10 to +10).
REAR L : To adjust the left rear speaker output level
(–10 to +10).
REAR R : To adjust the right rear speaker output level
(–10 to +10).
2) Press CONTROL UP 5/DOWN ∞
to adjust the selected speaker
output levels.
CONTROL
DOWN
UP
3) Repeat steps 1) and 2) to adjust the other
speaker output levels.
30
EN30-42.RX-7520V[C]f.pm5
30
CENTER
02.2.14, 4:33 PM
3
2
• To adjust the left rear speaker level, press
REAR•L +/– (–10 to +10).
Select the analog discrete output mode on the
DVD player, and start playing a DVD.
Adjust the speaker output levels.
1) Press ADJUST repeatedly until one of
the following indications appears on
the display.
SOUND
The 10 keys are activated for adjusting the sound.
• Refer also to the manual supplied with the DVD player.
3
DVD MULTI
Note:
Activating DVD MULTI Playback Mode
You can adjust the DVD MULTI playback mode while playing back
a DVD using the analog discrete output mode on the DVD player.
Once you have made adjustments, the receiver memorizes the
adjustments until you change them.
You also need to set the DVD player to the analog discrete output
mode.
Press DVD MULTI.
REAR L
6
REAR R
9
The COMPU LINK remote control system allows you to operate
JVC’s audio components through the remote sensor on the receiver.
To use this remote control system, you need to connect JVC’s audio
components through the COMPU LINK-4 (SYNCHRO) jacks (see
below) in addition to the connections using cables with RCA pin
plugs (see pages 6 and 7).
• Make sure that the AC power cords of these components are
unplugged before connection. Plug the AC power cords only after
all connections are completed.
English
COMPU LINK Remote Control System
Automatic Power On/Off (Standby): only possible with the
COMPU LINK-3 and COMPU LINK-4
Both the CD player and cassette deck (or CD recorder) turn on and
off (standby) along with the receiver.
When you turn on the receiver, the CD player or cassette deck (or
CD recorder) will turn on automatically, depending on which
component has been previously selected.
When you turn off the receiver, both the CD player and cassette
deck (or CD recorder) will turn off (standby).
Synchronized Recording
Cassette deck
or
CD recorder
Synchronized recording means the cassette deck starts recording as
soon as a CD begins playing.
To use synchronized recording, follow these steps:
1 Put a tape in the cassette deck and a disc in the
CD player.
COMPU LINK-4
(SYNCHRO)
2 Press the record (¶) button and the pause (8)
button on the cassette deck at the same time.
CD player
This puts the cassette deck into recording pause.
If you do not press the record (¶) button and pause (8) button at
the same time, the synchronized recording feature will not
operate.
3 Press the play (3) button on the CD player.
Notes:
• There are four versions of COMPU LINK remote control system.
This receiver is equipped with the fourth version—COMPU LINK-4.
This version is added systematic operations with the CD recorder to
the previous version—COMPU LINK-3.
• If your audio component has two COMPU LINK jacks, you can use
either one. If it has only one COMPU LINK jack, connect it so that it
is the last item in the series of components.
• To operate the cassette deck or CD recorder using the COMPU
LINK remote control system, set the source name correctly.
(See page 11.)
• Refer also to the manuals supplied with your audio components.
The source changes on the receiver, and as soon as play starts,
the cassette deck starts recording. When the play ends, the
cassette deck enters recording pause, and stops about 4 seconds
later.
Notes:
• During synchronized recording, the selected source cannot be
changed.
• If the power of any component is shut off during synchronized
recording, the COMPU LINK remote control system may not
operate properly. In this case, you must start again from the
beginning.
This remote control system allows you to use four functions listed
below.
Remote Control through the Remote Sensor on the Receiver
You can control the connected audio components through the remote
sensor on the receiver using this remote control. Aim the remote
control directly at the remote sensor on the receiver. For details, see
pages 34 and 35.
Automatic Source Selection
3) button on a connected component or
When you press the play (3
on its own remote control, the receiver automatically turns on and
changes the source to the component. On the other hand, if you
select a new source on the receiver or on the remote control, the
selected component begins playing immediately.
In both cases, the previously selected source continues playing
without sound for a few seconds.
31
EN30-42.RX-7520V[C]f.pm5
31
02.2.14, 4:33 PM
English
AV COMPU LINK Remote Control System
The AV COMPU LINK remote control system allows you to operate JVC’s video components (TV, VCR, and DVD player) through the
receiver.
This receiver is equipped with the AV COMPU LINK-III, which added a function to operate JVC’s video components through the video
components terminals. To use this remote control system, you need to connect the video components you want to operate, following the
diagrams below and the procedure on the next page.
CONNECTIONS 1: AV COMPU LINK Connection
VCR
TV
DVD player
VHS
DVD
AV
COMPU LINK – III
Note:
AV
COMPU LINK
AV
COMPU LINK
You can only connect to the TV
with the AV COMPU LINK EX or
AV COMPU LINK III terminal.
The TV with AV COMPU LINK
RECEIVER/AMP terminal will
not be used.
AV
COMPU LINK EX
AV
COMPU LINK III
Notes:
• When connecting the receiver and a TV with the AV COMPU LINK EX or AV COMPU LINK III terminal by using a component video cable, you
cannot use Automatic Selection of TV’s Input Mode (see page 33).
• When connecting only the VCR or DVD player to this receiver, connect it directly to the receiver using cables with the monaural mini-plugs.
• Make sure that the remote control code of the VCR connected to the VCR jacks is set to code “A”.
• Refer also to the manuals supplied with your video components.
CONNECTIONS 2: Video Cable Connections
This receiver is equipped with three types of video terminals—S-video, composite video, and component video, and the signals coming into
this receiver through one type of video terminal can output only through the same type of the terminal. So you need to connect the VCR and/
or DVD player to the TV using one of the following three ways:
CASE 1
When connecting the source equipment to the receiver using the S-video terminals, connect also this
receiver to the TV’s Video Input 1 terminal using S-video cables.
Source
Equipment
S-video cable
RX-7520VBK
S-video cable
TV
To Video Input 1
Note:
If you connect the DVD player and the VCR to this receiver using the S-video terminals, change the video input terminal
setting to “S/C” (see page 16).
CASE 2
When connecting the source equipment to the receiver using the composite video terminals, connect also
this receiver to the TV’s Video Input 2 terminal (composite video input) using composite video cables.
Source
Equipment
Composite
video cable
RX-7520VBK
Composite
video cable
TV
To Video Input 2
(Composite)
If you connect the DVD player and the VCR to this receiver using the composite video terminals, change the video input
terminal setting to “S/C” (see page 16).
Note:
CASE 3
When connecting the source equipment to the receiver using the component video terminals, connect also
this receiver to the TV’s Video Input 2 terminals (component video input) using component video cables.
Source
Equipment
Component
video cable
RX-7520VBK
Component
video cable
TV
To Video Input 2
(Component)
If you connect the DVD player and the VCR to this receiver using the component video terminals, change the video
input terminal setting to “COMPONENT” (see page 16).
Note:
32
EN30-42.RX-7520V[C]f.pm5
32
02.2.14, 4:33 PM
2. Connect your VCR, DVD player, TV and this
receiver as follows, using the cables with the
monaural mini-plugs (not supplied).
• See “CONNECTIONS 1” on the previous page.
3. Connect the audio input/output jacks on VCR,
DVD player, TV and this receiver, using the
cables with RCA pin plugs.
• See pages 7 and 8.
English
1. If you have already plugged your VCR, DVD
player, TV and this receiver into the AC outlets,
unplug their AC power cords first.
One-Touch DVD Play
Simply by starting playback on the DVD player, you can enjoy the
DVD playback without setting other switches manually.
• When the DVD player is connected through the analog input jacks
on this receiver (and analog input is selected), the receiver
automatically turns on and changes the source to “DVD” or “DVD
MULTI.”
• When the DVD player is connected through the digital input
terminal on this receiver (and digital input is selected), the receiver
automatically turns on and changes the source to “DVD
DIGITAL.”
The TV automatically turns on and changes the input mode to the
appropriate position so that you can view the playback picture.
Automatic Selection of TV’s Input Mode
4. Connect the video input/output jacks on VCR,
DVD player, TV and this receiver, using the
cables with RCA pin plugs, with S-video plug or
with component video plugs.
• See “CONNECTIONS 2” on the previous page.
5. Plug the AC power cords of the components into
the AC outlets.
6. When turning on the TV for the first time after
the AV COMPU LINK connection, turn the TV
volume to the minimum using the TV volume
control on the TV.
7. Turn on the other connected components first,
then turn on this receiver.
• When turning on the VCR, use the remote control supplied
VCR).
with this receiver (press STANDBY/ON
The AV COMPU LINK remote control system allows you to use the
five basic functions listed below.
Remote Control of the TV, DVD player, and VCR Using This
Remote Control
See page 36 for details.
• Aim the remote control directly at the remote sensor on each
target component.
• When you select “TV” as the source to play on the receiver, the
TV automatically changes the input mode to the TV tuner so that
you can watch TV.
• When you select “DVD,” “DVD MULTI,” or “VCR” as the source
to play on the receiver, the TV automatically changes the input
mode to the appropriate position (either Video Input 1 or Video
Input 2) so that you can view the playback picture.
Note:
When connecting a TV with the AV COMPU LINK EX or AV COMPU
LINK III terminal to this receiver, you cannot use a component video
cable (as in case 3 on page 32). Connect the TV using a S-video or
composite video cable (as in cases 1 and 2).
Automatic Power On/Off
The TV, VCR, and DVD player turn on and off along with the
receiver.
When you turn on the receiver;
• If the previously selected source is “VCR,” the TV and VCR will
turn on automatically.
• If the previously selected source is “TV SOUND,” only the TV
will turn on automatically.
• If the previously selected source is “DVD” or “DVD MULTI,” the
TV and DVD player will turn on automatically.
When you turn off the receiver, the TV, VCR and DVD player will
turn off.
Note:
If you turn off the receiver while recording on the VCR, the VCR will
not turn off, but continue recording.
One-Touch Video Play
Simply by inserting a video cassette without its safety tab into the
VCR, you can enjoy the video playback without setting other
switches manually. The receiver automatically turns on and changes
the source to “VCR.”
The TV automatically turns on and changes the input mode to the
appropriate position so that you can view the playback picture.
When you insert a video cassette with its safety tab, press the play
3) button on the VCR or on the remote control. So, you can get the
(3
same result.
33
EN30-42.RX-7520V[C]f.pm5
33
02.2.14, 4:33 PM
English
Operating JVC’s Audio/Video Components
You can use the remote control to operate other JVC’s
components.
Operating Audio Components
Sound Adjustment
You can always use the following buttons:
SURROUND ON/OFF : Turn on or off the Surround modes.
SURROUND MODE
: Select the Surround modes.
After pressing SOUND, you can use the following buttons for sound
adjustment:
SUBWOOFER +/–
: Adjust the subwoofer output level.
CENTER +/–
: Adjust the center speaker output level.
REAR•L +/–
: Adjust the left rear speaker output level.
REAR•R +/–
: Adjust the right rear speaker output level.
EFFECT
: Select the DAP effect level.
TEST
: Turn on or off the test tone output.
PTY–PTY SEARCH–PTY
Note:
After adjusting sounds, press the corresponding source selecting
button or CD–DISC to operate your target source by using the 10
keys; otherwise, the 10 keys cannot be used for operating your target
source.
FM MODE
Tuner
You can always use the following buttons:
FM/AM
: Alternate between FM and AM.
FM MODE
: Change the FM reception mode.
After pressing FM/AM, you can use the following buttons for tuner
operations:
1 – 10, +10
: Select a preset channel number directly.
• For channel number 5, press 5.
• For channel number 15, press +10, then 5.
• For channel number 20, press +10, then 10.
IMPORTANT:
CD player
To operate JVC’s audio components using this remote control:
• You need to connect JVC’s audio components through the COMPU
LINK-4 (SYNCHRO) jacks (see page 31) in addition to the
connections using cables with RCA pin plugs (see pages 6 and 7).
• Aim the remote control directly at the remote sensor on the receiver.
• If you use the buttons on the front panel, the remote control will not
operate that source. To operate a source with the remote control,
the source must be selected using source selecting buttons on the
remote control.
• To operate the cassette deck or CD recorder using the COMPU
LINK remote control system, set the source name correctly. (See
page 11.)
• Refer also to the manuals supplied with your audio components.
After pressing CD, you can use the following buttons for CD
operations:
3
: Start playback.
4
: Return to the beginning of the current
(or previous) track.
¢
: Skip to the beginning of the next track.
7
: Stop playback.
8
: Pause playback. To release it, press 3.
1 – 10, +10
: Select a track number directly.
• For track number 5, press 5.
• For track number 15, press +10, then 5.
• For track number 20, press +10, then 10.
34
EN30-42.RX-7520V[C]f.pm5
34
02.2.14, 4:33 PM
English
CD changer
Cassette deck
After pressing CD–DISC , you can use the following buttons for CD
changer operations:
After pressing TAPE/CDR, you can use the following buttons for
cassette deck operations:
3
: Start playback.
: Return to the beginning of the current
(or previous) track.
FF
: Fast wind a tape from left to right.
REW
: Fast wind a tape from right to left.
¢
: Skip to the beginning of the next track.
7
: Stop playback or recording.
7
: Stop playback.
8
: Pause playback. To release it, press 3.
8
: Pause playback. To release it, press 3.
REC PAUSE
1 – 6, 7/P
: Select the number of a disc installed in a CD
changer.
: Press this button to enter recording pause.
Press this button then 3 to start recording.
3
: Start playback.
4
Note:
If your CD changer is of 200-disc loading capability (except for
XL-MC100 and XL-MC301),
you can do the following operations using the number buttons after
pressing CD:
Before starting the above operations, make sure that you have
changed the source name correctly. See page 11.
1 Select a disc number.
2 Then select a track number (always enter two digits).
3 Start playback.
CD recorder
Examples:
• Selecting disc number 3, track number 2, and starting playback.
Press 3, then, 0, 2, then 3.
• Selecting disc number 10, track number 5, and starting playback.
Press 1, 0, then, 0, 5, then 3.
• Selecting disc number 105, track number 12, and starting
playback.
Press 1, 0, 5, then 1, 2, then 3.
After pressing TAPE/CDR, you can use the following buttons for
CD recorder operations:
3
: Start playback.
4
: Return to the beginning of the current
(or previous) track.
¢
: Skip to the beginning of the next track.
7
: Stop playback or recording.
8
: Pause playback. To release it, press 3.
REC PAUSE
: Press this button to enter recording pause.
Press this button then 3 to start recording.
Note:
Before starting the above operations, make sure that you have
changed the source name correctly. See page 11.
35
EN30-42.RX-7520V[C]f.pm5
35
02.2.14, 4:33 PM
English
Operating JVC’s Audio/Video Components
Operating Video Components
DVD player
You can always perform the following operations:
IMPORTANT:
STANDBY/ON
To operate JVC’s video components using this remote control:
• You need to connect JVC’s video components through the AV
COMPU LINK terminals (see page 32) in addition to the
connections using cables with RCA pin plugs (see pages 7 and 8).
• Some JVC’s VCRs can accept two types of the control signals—
remote code “A” and “B.” Before using this remote control, make
sure that the remote control code of the VCR connected to the
VCR jacks is set to code “A.”
• When using the remote control:
– For the DVD player and VCR operations, aim the remote control
directly at the remote sensor on each component, not on the
receiver.
– For the TV having the AV COMPU LINK terminal, aim the remote
control directly at the remote sensor on the TV.
VCR
You can always perform the following operations:
STANDBY/ON
VCR CH +/–
VCR
: Turn on or off a VCR.
DVD
: Turn on or off a DVD player.
After pressing DVD or DVD MULTI (source selecting button), you
can use the following buttons for DVD operations:
3
: Start playback.
4
: Return to the beginning of the current
(or previous) chapter.
¢
: Skip to the beginning of the next chapter.
7
: Stop playback.
8
: Pause playback. To release it, press 3.
DVD menu operations
After pressing DVD or DVD MULTI
(source selecting button), you can use
the following buttons for DVD menu
operations:
TEST
1
CENTER
EFFECT
4
REAR L
5
7/P
ENTER
10
After pressing VCR (source selecting button), you can use the
following buttons for VCR operations:
6
REAR R
MENU
: Change the TV channels on the VCR.
3
2
8
9
SUBWOOFER
0
RETURN
3
: Start playback.
MENU
: Display or erase the menu screen.
FF
: Fast wind a tape.
5/∞
∞/3
3/2
2
: Select an item on the menu screen.
REW
: Rewind a tape.
ENTER
: Enter a selected item.
7
: Stop playback or recording.
8
: Pause playback. To release it, press 3.
REC PAUSE
: Press this button to enter recording pause.
Press this button then 3 to start recording
10
100
TV
Before operating, set TV/CATV selector to TV.
You can always perform the following operations:
STANDBY/ON
TV/CATV
: Turn on or off a TV or a CATV converter.
TV/VIDEO
: Change the input mode (TV tuner and video
input).
TV VOLUME +/–
: Adjust the volume.
TV/CATV CH +/–
: Change the channels.
After pressing TV SOUND (source selecting button), you can use
the following buttons for TV operations:
1 – 9, 0, +10 (100+)
: Select a channel.
RETURN (10)
: Function as tme RETURN button.
36
EN30-42.RX-7520V[C]f.pm5
36
02.2.14, 4:33 PM
By changing the transmittable signals, you can use the remote
control supplied for this unit to operate other manufacturers’
equipment.
• Refer also to the manuals supplied for the other products.
• To operate these components with the remote control, first you
need to set the manufacturers’ code each for TV, CATV converter,
VCR and DVD player.
• After replacing batteries of the remote control, set the
manufacturers’ codes again.
Manufacturers’ codes for TV
Manufacturer
JVC
Hitachi
Magnavox
Mitsubishi
Panasonic
RCA
Samsung
Sanyo
Sharp
Sony
Toshiba
Zenith
To change the transmittable signals
for operating a TV
1
2
3
4
Set TV/CATV selector to TV.
Press and hold STANDBY/ON TV/CATV.
Press TV SOUND.
Enter manufacturer’s codes using buttons 1 – 9,
and 0.
5 Release STANDBY/ON TV/CATV.
Now, you can perform the following operations on the TV.
STANDBY/ON
TV/CATV
: Turn on or off the TV.
TV/VIDEO
: Set the input mode (either TV or VIDEO).
TV VOLUME +/–
: Adjust the volume.
TV/CATV CH +/–
: Change the channels.
After pressing TV SOUND (source selecting button), you can
use the following buttons on the TV:
1 – 10, +10 (100+) : Select a channel. +10 (100+) button will
function as the ENTER button if your
equipment requires pressing ENTER after
selecting a channel number.
English
Operating Other Manufacturers’ Video Equipment
Codes
01*
10
02
03
04, 11
05
12
13
06
07
08
09
* “01” is the initial setting.
To change the transmittable signals for
operating a CATV converter
1
2
3
4
Set TV/CATV selector to CATV.
Press and hold STANDBY/ON TV/CATV.
Press TV SOUND.
Enter manufacturer’s codes using buttons 1 – 9,
and 0.
5 Release STANDBY/ON TV/CATV.
Now, you can perform the following operations on the CATV
converter.
STANDBY/ON
TV/CATV
: Turn on or off the CATV converter.
TV/CATV CH +/–
: Change the channels.
After pressing TV SOUND (source selecting button), you can
use the following buttons on the CATV converter:
Note:
Refer also to the manual supplied with your TV.
6 Try to operate your TV by pressing
STANDBY/ON TV/CATV.
When your TV turns on or off, you have entered the correct
code.
1 – 10, +10 (100+) : Select a channel. +10 (100+) button will
function as the ENTER button if your
equipment requires pressing ENTER after
selecting a channel number.
Note:
Refer also to the manual supplied with your CATV converter.
If there are more than one code listed for your brand of TV,
try each one until the correct one is entered.
TO BE CONTINUED TO THE NEXT PAGE
37
EN30-42.RX-7520V[C]f.pm5
37
02.2.14, 4:33 PM
English
Operating Other Manufacturers’ Video Equipment
6 Try to operate your CATV converter by pressing
STANDBY/ON TV/CATV.
When your CATV converter turns on or off, you have entered
the correct code.
If there are more than one code listed for your brand of
CATV converter, try each one until the correct one is entered.
Manufacturers’ codes for CATV converter
Manufacturer
Echostar
General Instrument
Hamlin
Pioneer
RCA
Scient
Sony
Zenith
* “01” is the initial setting.
Codes
01*
02, 03, 04, 05, 06,
07, 08, 09
16, 17, 18, 19
14, 15
20
10, 11
21
12, 13
To change the transmittable signals for
operating a VCR
1 Press and hold STANDBY/ON VCR.
2 Press VCR.
3 Enter manufacturer’s codes using buttons 1 – 9,
and 0.
4 Release STANDBY/ON VCR.
Now, you can perform the following operations on the VCR.
STANDBY/ON
VCR
VCR CH +/–
: Turn on or off the VCR.
: Change the channels.
After pressing VCR (source selecting button), you can use the
following buttons on the VCR:
3
: Start playback.
FF
: Fast-wind a tape.
REW
: Rewind a tape.
7
: Stop playback or recording.
8
: Pause playback. To release it, press 3.
REC PAUSE
: Press this button to enter recording
pause.
Press this button then press 3 to start
recording.
Note:
Refer also to the manual supplied with your VCR.
5 Try to operate your VCR by pressing
STANDBY/ON VCR.
When your VCR turns on or off, you have entered the correct
code.
If there are more than one code listed for your brand of
VCR, try each one until the correct one is entered.
Manufacturers’ codes for VCR
Manufacturer
JVC
Emerson
Gold Star
Hitachi
Mitsubishi
NEC
Panasonic
Philips
RCA
Samsung
Sanyo
Sony
Zenith
* “01” is the initial setting.
38
EN30-42.RX-7520V[C]f.pm5
38
02.2.14, 4:33 PM
Codes
01*, 02, 03
10, 22
11
04
12
21
07, 13
09
05, 06
20
17, 18, 19
14, 15, 16
08
Manufacturers’ codes for DVD player
Manufacturer
1 Press and hold STANDBY/ON DVD.
2 Press DVD.
3 Enter manufacturer’s codes using buttons 1 – 9,
and 0.
4 Release STANDBY/ON DVD.
Now, you can use the following buttons on the DVD player.
STANDBY/ON
DVD
English
To change the transmittable signals for
operating a DVD player
JVC
Panasonic
Philips
Pioneer
Sony
Toshiba
Yamaha
Codes
01*
02
04
03
05
06
07
* “01” is the initial setting.
: Turn on or off the DVD player.
After pressing DVD (source selecting button), you can use the
following buttons on the DVD player:
3
: Start playback.
7
: Stop playback.
4
: Return to the beginning of the
current (or previous) chapter.
¢
: Skip to the beginning of the next
chapter.
8
: Pause playback. To release it, press 3.
DVD menu operations
After pressing DVD (source
selecting button), you can use the
following buttons for DVD menu
operations:
TEST
1
CENTER
REAR L
5
7/P
10
6
REAR R
MENU
ENTER
3
2
EFFECT
4
Manufacturers’ codes are subject to change
without notice. If they are changed, this remote
control cannot operate the equipment.
8
9
SUBWOOFER
0
RETURN
MENU
: Display or erase the menu screen.
5/∞
∞/3
3/2
2
: Select an item on the menu screen.
ENTER
: Enter a selected item.
10
100
5 Try to operate your DVD player by pressing
STANDBY/ON DVD.
When your DVD player turns on or off, you have entered the
correct code.
If there are more than one code listed for your brand of DVD
player, try each one until the correct one is entered.
39
EN30-42.RX-7520V[C]f.pm5
39
02.2.14, 4:33 PM
English
Troubleshooting
Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC’s service center.
PROBLEM
POSSIBLE CAUSE
SOLUTION
The power does not come on.
The power cord is not plugged in.
Plug the power cord into an AC outlet.
No sound from speakers.
Speaker signal cables are not connected.
Check speaker wiring and reconnect if
necessary.
The SPEAKERS ON/OFF 1 and 2 buttons
are not set correctly.
Press SPEAKERS ON/OFF 1 and 2 buttons
correctly.
An incorrect source is selected.
Select the correct source.
Muting is activated.
Press MUTING to cancel the mute.
An incorrect input mode (analog or
digital) is selected.
Select the correct input mode (analog or
digital).
Connections are incorrect.
Check connections.
For analog connections, see pages 6 – 8.
For digital connections, see page 9.
Speaker signal cables are not connected
properly.
Check speaker wiring and reconnect if
necessary.
The balance is set to one extreme.
Adjust the balance properly (see page 19).
Incoming signal is too weak.
Connect an outdoor FM antenna or contact
your dealer.
The station is too far away.
Select a new station.
An incorrect antenna is used.
Check with your dealer to be sure you have
the correct antenna.
Antennas are not connected properly.
Check connections.
Occasional cracking noise during FM
reception.
Ignition noise from automobiles.
Move the antenna farther from automobile
traffic.
Howling during record playing
Your turntable is too close to speakers.
Move speakers away from the turntable.
Noise is heard.
An earth (H) cable is not connected to the
AM (H) terminal on the rear panel.
Connect the cable to the AM (H) terminal on
the rear panel.
“OVERLOAD” starts flashing on the
display.
Speakers are overloaded because of high
volume.
on the front
1. Press STANDBY/ON
panel to turn off the receiver.
2. Stop the playback source.
3. Turn on the receiver again, and adjust the
volume.
Speakers are overloaded because of short
circuit of speaker terminals.
on the front panel,
Press STANDBY/ON
then check the speaker wiring.
If “OVERLOAD” does not disappear, unplug
the AC power cord, then plug it back again.
If speaker wiring is not short-circuited, contact
your dealer.
“DSP MICOM NG” starts flashing on the
display.
The built-in microcomputer is not
functioning correctly.
on the front panel to
Press STANDBY/ON
turn off the receiver. After unplugging the
power cord, consult your dealer.
The STANDBY lamp lights up after
turning on the power, but soon the
receiver turns off (into standby mode).
The receiver is overloaded because of a
high voltage.
on the front panel to
Press STANDBY/ON
turn off the receiver. After unplugging the
power cord, consult your dealer.
Remote control does not work.
There is an obstruction in front of the
remote sensor on the receiver.
Remove the obstruction.
Batteries are weak.
Replace batteries.
The remote control is not ready for your
intended operation.
Press SOUND or source selecting buttons
first, then press the button you want to use.
(See pages 20, 27, 28, 34 – 39).
Sound from one speaker only.
Continuous hiss or buzzing during FM
reception.
Remote control does not operate as you
intend.
40
EN30-42.RX-7520V[C]f.pm5
40
02.2.14, 4:33 PM
Specifications
English
Designs & specifications are subject to change without notice.
Amplifier
Output Power
At Stereo operation:
Front channels:
100 W per channel, min. RMS, driven into 8 Ω,
40 Hz to 20 kHz with no more than 0.8% total
harmonic distortion.
At Surround operation:
Audio
Audio Input Sensitivity/Impedance (1 kHz):
Front channels:
100 W per channel, min. RMS, driven into 8 Ω at 1 kHz, with no
more than 0.8% total harmonic distortion.
Center channel:
100 W, min. RMS, driven into 8 Ω at 1 kHz, with no more than
0.8% total harmonic distortion.
Rear channels:
100 W per channel, min. RMS, driven into 8 Ω at 1 kHz, with no
more than 0.8% total harmonic distortion.
CD, TAPE/CDR, VCR, TV SOUND, DVD:
220 mV/47 kΩ
Audio Input (DIGITAL IN)* :
0.5 V (p-p)/75 Ω
–21 dBm to –15 dBm (660 nm ±30 nm)
Coaxial: DIGITAL 1 (DVD):
Optical: DIGITAL 2 (CD):
* Corresponding to Linear PCM, Dolby Digital, and DTS Digital Surround
(with sampling frequency — 32 kHz, 44.1 kHz, 48 kHz).
Audio Output Level:
Signal-to-Noise Ratio (’66 IHF/’78 IHF):
TAPE/CDR, VCR:
220 mV
CD, TAPE/CDR, VCR, TV SOUND, DVD:
87 dB/78 dB
Frequency Response (8 Ω):
CD, TAPE/CDR, VCR, TV SOUND, DVD: 20 Hz to 20 kHz (±1 dB)
Bass boost:
Tone Control:
+3 dB ±1 dB at 100 Hz
Bass (100 Hz):
Treble (10 kHz):
±10 dB
±10 dB
Video
Video Input Sensitivity/Impedance:
Composite video:
S-video:
DVD, VCR:
DVD, VCR:
Component video:
DVD, VCR:
Video Output Level/Impedance:
Composite video:
S-video:
Component video:
Synchronization:
Signal-to-Noise Ratio:
VCR, MONITOR OUT:
VCR, MONITOR OUT:
MONITOR OUT:
(Y: luminance):
(C: chrominance, burst):
(Y: luminance):
(PB/CB, PR/CR):
1 V(p-p)/75 Ω
1 V(p-p)/75 Ω
0.286 V(p-p)/75 Ω
1 V(p-p)/75 Ω
0.7 V(p-p)/75 Ω
(Y: luminance):
(C: chrominance, burst):
(Y: luminance):
(PB/CB, PR/CR):
1 V(p-p)/75 Ω
1 V(p-p)/75 Ω
0.286 V(p-p)/75 Ω
1 V(p-p)/75 Ω
1 V(p-p)/75 Ω
Negative
45 dB
41
EN30-42.RX-7520V[C]f.pm5
41
02.2.14, 4:33 PM
English
Specifications
FM tuner (IHF)
Tuning Range:
87.5 MHz to 108.0 MHz
Usable Sensitivity:
Monaural:
12.8 dBf (1.2 µV/75 Ω)
50 dB Quieting Sensitivity:
Monaural:
Stereo:
21.3 dBf (3.2 µV/75 Ω)
41.3 dBf (31.5 µV/75 Ω)
Signal-to-Noise Ratio (IHF-A weighted):
Monaural:
Stereo:
78 dB at 85 dBf
73 dB at 85 dBf
Total Harmonic Distortion:
Monaural:
Stereo:
0.4% at 1 kHz
0.6% at 1 kHz
Stereo Separation at REC OUT:
Alternate Channel Selectivity:
Frequency Response:
35 dB at 1 kHz
45 dB: (±400 kHz)
30 Hz to 15 kHz: (+0.5 dB, –3 dB)
AM tuner
Tuning Range:
Usable Sensitivity:
Signal-to-Noise Ratio:
530 kHz to 1 710 kHz
Loop antenna:
400 µV/m
50 dB (100 mV/m)
General
Power Requirements:
AC 120V
Power Consumption:
180 W/230 VA (at operation)
2 W (in standby mode)
Dimensions (W x H x D):
Mass:
, 60 Hz
435 mm x 146.5 mm x 416 mm
(17 3/16 in. x 5 13/16 in. x 16 7/16 in.)
8.8 kg (19.5 lbs)
42
EN30-42.RX-7520V[C]f.pm5
42
02.2.14, 4:33 PM
VICTOR COMPANY OF JAPAN, LIMITED
V
EN, FR
RX-7520VBK[C]Cover.pm5
J
2
02.2.14, 4:30 PM
C
0202NHMMDWJEIN