advertisement
XV-521BK [1U] EN
LVT0435-011A
DVD VIDEO PLAYER
XV-521BK
Introduction
1
Preliminary knowledge
4
Getting started
12
Basic operations
17
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
PLAY MODE DISPLAY RETURN
SHIFT
B.SEAR
B.SKI
CH
P
CANCEL
PLAY
TIME CHOICE
F.SEARC
H
F.SKIP
PAUS
E
STOP
ENTER
MENU
TITLE
LEFT
UP
CURSOR RIGHT
DOWN
REMOTE CONTROL
Advanced operations
20
POWER
DVD PLAYER
STANDBY
3D PHONIC
D I G
DOLBY
I T A L
1
SHUTTLE
¡
OPEN/CLOSE
0
TITLE CHAP.
EACH
RESUME THEATER
4
SKIP
¢
DVD / VDEO CD / CD
INSTRUCTIONS
'
Initial settings
35
Additional information
41
For Customer Use:
Enter below the Model No. and Serial No.
which are located on the rear, bottom or side of the cabinet. Retain this information for future reference.
Model No.
Serial No.
LVT0435-011A
[1U]
00.6.9, 3:29 PM EN XV-521BK[1U]COVER 1
XV-521BK [1U] EN
LVT0435-011A
Warnings, Cautions and Others
Mises en garde, précautions et indications diverses
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
For U.S.A.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
ATTENTION
Afin d'éviter tout risque d'électrocution, d'incendie, etc.:
1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de l'appareil.
2. Ne pas exposer l'appareil à la pluie ni à l'humidité.
Caution –– POWER switch!
Disconnect the mains plug to shut the power off completely. The
POWER switch in any position does not disconnect the mains line. The power can be remote controlled.
Attention –– Commutateur POWER!
Déconnecter la fiche de secteur pour couper complètement le courant.
Le commutateur POWER ne coupe jamais complètement la ligne de secteur, quelle que soit sa position. Le courant peut être télécommandé.
IMPORTANT FOR LASER PRODUCTS
IMPORTANT POUR LES PRODUITS LASER
1.
CLASS 1 LASER PRODUCT
2.
DANGER: Visible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam.
3.
CAUTION: Do not open the top cover. There are no user serviceable parts inside the Unit; leave all servicing to qualified service personnel.
1.
PRODUIT LASER CLASSE 1
2.
ATTENTION: Radiation laser visible quand l'appareil est ouvert ou que le verrouillage est en panne ou désactivé. Eviter une exposition directe au rayon.
3.
ATTENTION: Ne pas ouvrir le couvercle du dessus. Il n'y a aucune pièce utilisable à l'intérieur. Laisser à un personnel qualifié le soin de réparer votre appareil.
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
For Canada/pour le Canada
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT
ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQUAU FOND
For Canada/pour le Canada
THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B
LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL
APPARATUS AS SET OUT IN THE INTERFERENCE-CAUSING
EQUIPMENT STANDARD ENTITLED "DIGITAL APPARATUS",
ICES-003 OF THE DEPARTMENT OF COMMUNICATIONS.
CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE
BRUITS RADIOELECTRIQUES APPLICABLES AUX APPAREILS
NUMERIQUES DE CLASSE B PRESCRITES DANS LA NORME
SUR LE MATERIEL BROUILLEUR: "APPAREILS NUMERIQUES",
NMB-003 EDICTEE PAR LE MINISTRE DES COMMUNICATIONS.
EN XV-521BK[1U]SAFETY 2 00.6.9, 3:29 PM
XV-521BK [1U] EN
LVT0435-011A
Introduction
Table of contents
Introduction
Page 1
Features .................................................................... 1
Supplied accessories ............................................... 1
About this instruction manual ............................... 2
Notes on handling ................................................... 3
Preliminary knowledge
Page 4
Names of parts and controls
Front panel ................................................................... 4
Remote control unit .................................................... 5
Display window ........................................................... 7
Rear panel .................................................................... 7
Operational Principles
On-screen displays ...................................................... 8
To prevent the monitor from burning out
[SCREEN SAVER] ...................................................... 9
On-screen guide icons .............................................. 10
How to use numeric buttons .................................... 10
About discs
Playable disc types .................................................... 11
Disc structure ............................................................. 11
Getting started
Page 12
Connections
Before making any connections .............................. 12
To connect to a TV ..................................................... 12
To connect to a TV with the component video input jacks ................................................................ 13
To connect to an audio amplifier or receiver ......... 13
To connect to audio equipment with a digital input ......................................................................... 14
To connect the power cord ....................................... 14
Using the remote control unit
To install batteries in the remote control unit ........ 15
To use the remote control unit for TV operation ... 16
To control the volume of a JVC’s amplifier or receiver .................................................................... 16
Basic operations
Page 17
Turning on/off the unit .......................................... 17
Inserting and removing discs ............................... 17
Basic playback
To start playback ....................................................... 18
To stop playback completely ................................... 18
To stop playback temporarily .................................. 18
To advance or reverse playback rapidly while monitoring ............................................................... 18
To locate the beginning of the scene or song ........ 19
To resume playback
To memorize the interrupted position .................... 19
To resume playback .................................................. 19
Advanced operations
Page 20
Playing from a specific position on a disc
To locate a desired scene from the DVD menu ...... 20
To locate a desired scene from the menu of the
Video CD with PBC .................................................. 20
To locate a desired selection using the numeric buttons ..................................................................... 21
To locate a desired selection using 4 or ¢ ...... 21
To locate a desired scene by specifying the chapter number [CHAP. SEARCH] ....................................... 22
To locate a desired position in the current title or track [TIME SEARCH] .............................................. 22
To locate a desired scene from the digest display
[DIGEST] .................................................................. 23
Special picture playback
To advance a still picture frame-by-frame .............. 24
To display still pictures [STROBE] ........................... 24
To playback in slow-motion [SLOW] ....................... 25
To zoom a scene [ZOOM] ......................................... 26
Changing the playback order
To playback in the desired order [PROGRAM] ....... 26
To playback in random order [RANDOM] ............... 27
Repeat playback
To repeat the current selection or all disc contents [REPEAT] ................................ 28
To repeat a desired part [A-B REPEAT] ................... 29
Selecting a scene angle of DVD VIDEO
To select a scene angle from the normal screen
[ANGLE] ................................................................... 30
To select a scene angle from the angle list display
[ANGLE] ................................................................... 30
Changing the language and sound
To select the subtitle language [SUBTITLE] ........... 31
To change the audio language or sound [AUDIO] . 31
Selecting the picture character
To select the picture character
[THEATER POSITION] ............................................. 32
Enjoying virtual surround sound
To simulate surround sound [3D PHONIC] ............. 32
Checking the status
To check the disc/time information ......................... 33
To check the DVD function status ............................ 34
Initial settings
Page 35
Selecting preferences
How to set preferences ............................................. 35
LANGUAGE page ...................................................... 35
AUDIO page ............................................................... 36
DISPLAY page ............................................................ 37
SYSTEM page ............................................................ 38
Limiting playback by children
To set Parental Lock for the first time
[PARENTAL LOCK] .................................................. 39
To change the settings [PARENTAL LOCK] ............. 40
To temporarily release the Parental lock
[PARENTAL LOCK] .................................................. 40
Additional information
Page 41
AV COMPU LINK remote control system
Connection and setup ............................................... 41
Operation ................................................................... 42
Care and handling of discs .................................... 42
Troubleshooting ..................................................... 43
Specifications ......................................................... 44
Table of languages and their
abbreviations ....................................... Appendix A
Country code list for parental lock ...... Appendix B
00.6.9, 3:29 PM EN XV-521BK[1U]CONTENTS 1
XV-521BK [1U] EN
LVT0435-011A
Introduction
Introduction
Features
Picture functions
7
Strobe function
The unit can display nine continuous still pictures on the TV screen.
7
Digest function
You can select the desired title from the opening scenes displayed on the TV screen.
7
Angle function*
You can select a desired angle from multiple camera angles recorded on the DVD VIDEO disc.
7
Zoom function
You can view scenes close-up.
7
Parental lock*
You can restrict the playback of DVD VIDEO discs with scenes which you do not want children to see, such as adult or violent films.
7
Theater position
You can select the picture character according to the lighting of your room.
Audio functions
7
High quality digital sound
You can enjoy high quality sound with Dolby Digital or Linear-PCM.
7
Surround function*
The unit is compatible with Dolby Digital surround and
DTS surround.
(DTS surround is available for digital output only.)
7
3D Phonic function
You can enjoy surround sound with your 2-channel system.
Other functions
7
Multi-language subtitles and sound*
You can select a subtitle or sound language from those recorded on the DVD VIDEO disc.
7
Multi-disc playback
You can enjoy Audio CD discs and Video CD discs, as well as DVD VIDEO discs.
7
Operation from the on-screen display
User-friendly on-screen displays allow you to operate the unit easily.
Functions with (*) mark only work on a DVD VIDEO disc that is compatible with each function.
Supplied accessories
• Audio/video cable (x 1)
• S-video cable (x 1)
• AV compulink cord (x 1)
• Remote Control Unit (x 1)
LEFT
UP
SHIFT
8
SE
4
KIP H
TITL
E
7
P
MENU
3
SLOW
CANCEL
10
TV R
ET
UR
N
PLAY MODE
TIME
DISPLAY
TV 7
7
VO
TV
L
TV
4
TV
0
0
RETURN
4 TV 1
1
TV 8
8
/C
LO
SE
N
DIG
EST
SU
BT
ITL
E
STR
OB
E
AU
DIO
TV
5
5 TV
2
2
6
ZO
3D
-P
NIC
OM
AN
GLE
PO
THE
AT
ER
N
TV
/VIDE
O
TV 3
3
9
TV
6 ch
TV
+10
TV
10
0+
TV
9
¢
F.S
KIP
RC
H
CHOICE
ENTER
TV
DVD
PO
PO WE
R
DOWN OR
RM
-S
XV5
21J REM
OTE
C
TR
OL
RIGHT
• R6P(SUM-3)/AA(15F) batteries (x 2)
• Instruction manual (x 1)
• AC power cord (x 1)
• AC plug adapter (x 1)
1
EN01-03.XV-521BK[1U] 1 00.6.9, 3:29 PM
XV-521BK [1U] EN
LVT0435-011A
Introduction
About this instruction manual
This instruction manual basically explains operations as follows:
The number indicates the procedural step.
Other convenient procedures, etc.
Additional supplemental remarks
To playback in random order [RANDOM]
You can play titles or tracks in random order by using the Random function.
1
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
PLAY MODE DISPLAY RETURN
SHIFT CANCEL
B.SEA
RCH
TIME CHOICE
F.SEARC
H
ENTER
TITLE
MENU
LEFT
UP
CURSOR
RIGHT
DOWN
3
2
REMOTE CONTROL
7
While stopped
1
Press PLAY MODE - CANCEL.
The play mode menu appears on the TV screen.
2
Use CURSOR 2/3 to move to
[RANDOM].
REPEAT PROGRAM RANDOM
The “RANDOM” indicator appears in the display window on the front panel.
3
Press ENTER.
The unit starts random playback.
After playing all titles/tracks of the disc, random playback ends.
The same title or track will not be played back more than once during random play.
• To stop/quit random playback in the middle
Press STOP to stop playback. The unit is still in random playback mode, so pressing PLAY starts random playback again.
To quit random playback, press STOP again while stopped. The “RANDOM” indicator in the display window turns off.
NOTE
Some DVD VIDEO discs may not be played back correctly in random mode.
These symbols indicate the types of discs which the operation can be used for.
The number indicates the following procedural step(s) in which the button(s) is(are) used.
You may also use the corresponding buttons on the front panel of the unit if available.
The names of buttons on the remote control unit
(or on the front panel of the unit) are all given in uppercase letters.
2
EN01-03.XV-521BK[1U] 2 00.6.9, 3:29 PM
XV-521BK [1U] EN
LVT0435-011A
Introduction
Notes on handling
Important cautions
Installation of the unit
• Select a place which is level, dry and neither too hot nor too cold (between 5˚C and 35˚C, 41˚F and 95˚F).
• Leave sufficient distance between the unit and the TV.
• Do not use the player in a place subject to vibrations.
Power cord
• Do not handle the power cord with wet hands!
• A small amount of power (3.0 watts) is always consumed while the power cord is connected to the wall outlet.
• When unplugging the player from the wall outlet, always pull the plug, not the power cord.
To prevent malfunction of the unit
• There are no user-serviceable parts inside. If anything goes wrong, unplug the power cord and consult your dealer.
• Do not insert any metallic object into the unit.
• Do not use any non-standard shape disc available on the market, because it may damage the unit.
• Do not use a disc with tape, seals, or paste on it, because damage to the unit may result.
Note about copyright laws
• Please check the copyright laws in your country before recording from DVD VIDEO, Audio CD, and
Video CD discs. Recording of copyrighted material may infringe copyright laws.
Note about the copyguard system
• The DVD VIDEO disc is protected by the copyguard system. When you connect the unit to your VCR directly, the copyguard system activates and the picture may not be played back correctly.
Safety precautions
Avoid moisture, water and dust
Do not place the unit in moist or dusty places.
Avoid high temperatures
Do not expose the unit to direct sunlight or place it near a heating device.
When you’re away
When away on travel or otherwise for an extended period of time, remove the plug from the wall outlet.
Do not insert foreign objects into the unit
Do not insert wires, hairpins, coins, etc. into the unit.
Do not block the vents
Blocking the vents may damage the unit.
Care of the cabinet
When cleaning the unit, use a soft cloth and follow the relevant instructions on the use of chemically-coated cloths. Do not use benzene, thinner or other organic solvents and disinfectants. These may cause deformation or discoloring.
If water gets inside the unit
Turn off the power switch and remove the plug from the wall outlet, then call the store where you made your purchase. Using the unit in this state may cause a fire or electrical shock.
This product incorporates copyright protection technology that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
Manufactured under license from Dolby Laboratories. “Dolby” and double-D symbol are trademarks of Dolby
Laboratories.
Confidential Unpublished Works.
© 1992-1997 Dolby Laboratories, Inc. All rights reserved.
Manufactured under license from Digital Theater Systems, Inc. US Pat. No. 5,451,942 and other world-wide patents issued and pending. “DTS”, “DTS Digital Surround”, are trademarks of Digital Theater Systems, Inc.
© 1996 Digital Theater Systems, Inc. All Rights Reserved.
3
EN01-03.XV-521BK[1U] 3 00.6.9, 3:29 PM
XV-521BK [1U] EN
LVT0435-011A
Preliminary knowledge
Names of parts and controls
Refer to the corresponding pages indicated in () for details.
Front panel
Preliminary knowledge
1 POWER button
2 STANDBY indicator
3 Remote sensor
POWER
DVD PLAYER
STANDBY
3D PHONIC
D I G
DOLBY
I T A L
4 Disc tray
5 0 (OPEN/CLOSE) button
6 7 (STOP) button
7 # (PLAY) button
8 8 (PAUSE) button
= SHUTTLE knob
TITLE CHAP.
EACH
RESUME THEATER
OPEN/CLOSE
0
STOP
7
PAUSE
8
1
SHUTTLE
¡
4
SKIP
¢
DVD / VDEO CD / CD
9 3D PHONIC button 0 Display window 4/¢ (SKIP) buttons
1 POWER button (17)
Turns the unit on or off (standby).
2 STANDBY indicator
Lights when the power cord is connected and the unit is on standby. When the unit is turned on, the STANDBY indicator goes off.
3 Remote sensor
Receives the signal from the remote control unit.
4 Disc tray (17)
Used to load a disc.
5 0 (OPEN/CLOSE) button (17)
Used to open and close the disc tray.
6 7 (STOP) button (18)
Stops playback.
Also used to erase all programmed tracks for the program play.
7 # (PLAY) button (18)
Starts playback. Also, used as a SELECT button for the PBC of Video CDs.
8 8 (PAUSE) button (18)
Pauses playback.
9 3D PHONIC button (32)
Produces a simulated surround effect.
0 Display window
Indicates the current status of the unit.
4/¢ (SKIP) buttons (19, 21)
Used to skip a chapter, title or track.
Also, used for the page selection of a menu screen (for
DVD VIDEO/Video CD).
Holding down 4 or ¢ during playback reverses or advances playback rapidly.
= SHUTTLE knob (19, 25)
Performs rapid advance/reverse playback operations.
Also used for slow-motion playback of a picture (for DVD
VIDEO/Video CD).
4
EN04-11.XV-521BK[1U] 4 00.6.9, 3:29 PM
XV-521BK [1U] EN
LVT0435-011A
Preliminary knowledge
Remote control unit
1 3D PHONIC button
2 OPEN/CLOSE button
3 SUBTITLE - DIGEST button
4 AUDIO - STROBE button
5 Numeric buttons
6 SLOW button
7 AMP VOL button
8 SHIFT button
9 PLAY MODE - CANCEL button
0 4 (B.SKIP) - B. SEARCH button
8 (PAUSE) button
= TITLE button
~ CURSOR ( 5 UP, ∞ DOWN,
2 LEFT, 3 RIGHT) button
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100 +
SLOW
AMP
VOL
TV
VOL
TV ch
PLAY MODE DISPLAY RETURN
SHIFT
B.SEARC
H
B.SKIP
4
CANCEL
PLAY
3
TIME CHOICE
F.SEARC
H
F.SKIP
¢
STOP
7 ENTER
TITLE
MENU
UP
LEFT CURSOR RIGHT
DOWN
! Infrared signal-emitting window
@ THEATER POSITION button
# DVD POWER - TV POWER button
$ TV/VIDEO button
% ANGLE - ZOOM button
^ TV ch button
& TV VOL button
* RETURN - CHOICE button
( DISPLAY - TIME button
) ¢ (F.SKIP) - F. SEARCH button
_ 3 (PLAY) button
+ ENTER button
¡ 7 (STOP) button
™ MENU button
REMOTE CONTROL
5
EN04-11.XV-521BK[1U] 5 00.6.9, 3:29 PM
XV-521BK [1U] EN
LVT0435-011A
Preliminary knowledge
1 3D PHONIC button (32)
Produces a simulated surround effect.
2 OPEN/CLOSE button (17)
Opens and closes the disc tray.
3 SUBTITLE - DIGEST button (23, 31)
Used to display the subtitle selection display on the TV screen, as well as used to turn the subtitle on or off (for
DVD VIDEO).
Pressing this button while holding down the SHIFT button displays beginning scenes of each title, chapter or track on the TV screen (for DVD VIDEO/Video CD).
4 AUDIO - STROBE button (24, 31)
Selects the audio (for DVD VIDEO/Video CD). Pressing this button while holding down the SHIFT button displays nine continuous still pictures (for DVD VIDEO/Video CD).
5 Numeric buttons (10, 16)
Used to select a title or track number, as well as used to enter a time for the Time search and a chapter number for the Chapter search.
Also used to select a TV channel in conjunction with the
SHIFT button.
6 SLOW button (25)
Used for slow-motion playback of a picture (for DVD VIDEO/
Video CD).
7 AMP VOL button (16)
Used to control the volume of a JVC audio amplifier/ receiver.
8 SHIFT button
Used together with other buttons for activating their second functions.
9 PLAY MODE - CANCEL button (27)
Displays an on-screen display for controlling the advanced playback functions. Pressing this button while holding down the SHIFT button cancels the last selection of the program.
0 4 (B.SKIP) - B. SEARCH button (19, 21, 23)
Skips back a chapter, title or track. Also used for the page selection of a menu screen (for DVD VIDEO/Video CD).
Holding down this button during playback reverses playback rapidly.
Pressing the button while holding down the SHIFT button during playback also reverses playback rapidly. If you press the button while holding down the SHIFT button during rapid reverse playback, the speed increases.
8 (PAUSE) button (18)
Pauses playback.
= TITLE button (20)
Displays the title menu of a DVD VIDEO disc on the TV screen.
~ CURSOR ( 5 UP, ∞ DOWN, 2 LEFT, 3 RIGHT) buttons
Used to select an item form a menu or on-screen display, or to change the setting of an item in the on-screen display.
! Infrared signal-emitting window
Point this window toward the remote sensor on the front panel when pressing buttons.
@ THEATER POSITION button (32)
Selects a picture character from 4 options (for DVD VIDEO/
Video CD).
# DVD POWER - TV POWER button (17)
Turns the unit on or off (standby). Pressing this button while holding down the SHIFT button turns the TV on or off.
$ TV/VIDEO button (16)
Switches the TV input mode.
% ANGLE - ZOOM button (26, 30)
Changes camera angles during playback of a DVD VIDEO disc containing multiple camera angles. Pressing this button while holding down the SHIFT button zooms in the picture (for DVD VIDEO/Video CD).
^ TV ch button (16)
Changes the TV channels.
& TV VOL button (16)
Adjusts the TV volume.
* RETURN - CHOICE button (20, 35)
Returns to the previous menu (for DVD VIDEO/Video CD).
Pressing this button while holding down the SHIFT button displays Preference on-screen display on the TV screen.
( DISPLAY - TIME button (33, 34)
Displays the status information (only for DVD disc) or the time information (for any disc types). When the time information appears, pressing this button while holding the SHIFT button changes the time mode.
) ¢ (F.SKIP) - F. SEARCH button (19, 21, 23)
Skips forward a chapter, title or track. Also used for the page selection of a menu screen (for DVD VIDEO/Video CD).
Holding down this button during playback advances playback rapidly.
Pressing the button while holding down the SHIFT button during playback also advances playback rapidly. If you press the button while holding down the SHIFT button during rapid advance playback, the speed increases.
_ 3 (PLAY) button (18)
Starts playback. Also used as a SELECT button for PBC of
Video CDs.
+ ENTER button
Executes the selected item in a menu or on-screen display.
¡ 7 (STOP) button (18)
Stops playback.
Also used to erase all the programmed tracks for the program play.
™ MENU button (20)
Displays a DVD menu on the TV screen.
6
EN04-11.XV-521BK[1U] 6 00.6.9, 3:29 PM
XV-521BK [1U] EN
LVT0435-011A
Preliminary knowledge
Display window
3 Disc indicator
4 Function indicator
3D-PHONIC
TITLE CHAP.
TRACK
PROGRAM RANDOM
RESUME
REPEAT 1A-B
THEATER
DVD VCD
EACH
REMAIN
2 Time display
1 Title/chapter/track indicator
1 Title/chapter/track indicator
Displays title/chapter, or track number.
2 Time display
Shows the cumulative or remaining time of the track or disc, or the total disc time.
3 Disc indicator
Indicates the type of the disc set in the tray. When a DVD
VIDEO or Video CD disc is set, “DVD” or “VCD” is indicated.
When an Audio CD is set, there is no indication.
4 Function indicator
Activated function indicators light up.
Rear panel
6 DIGITAL OUT jacks (OPTICAL/COAXIAL)
7 COMPONENT VIDEO OUT jacks (Y/P
B /P R )
DIGITAL OUT
PCM/STREAM
COAXIAL
OPTICAL
Y
VIDEO OUT
COMPONENT
P
B
P
R
S-VIDEO VIDEO
R L
AUDIO OUT
3 AUDIO OUT jacks
(LEFT/RIGHT)
2 VIDEO OUT jack
1 S-VIDEO OUT jack
AV COMPU LINK
4 AV COMPU LINK jacks
AC IN
1
5 AC IN connector
1 S-VIDEO OUT jack (12)
Outputs an S-video signal.
2 VIDEO OUT jack (12)
Outputs a composite video signal.
3 AUDIO OUT jacks (L/R) (12)
Output stereo analog audio signals.
4 AV COMPU LINK jacks (41)
Connect with other JVC equipment supporting the AV
Compulink function to facilitate integrated operations.
5 AC IN connector (14)
Connects to the wall outlet using the supplied AC power cord.
6 DIGITAL OUT jacks (14)
Output digital audio signals. You must select the signal type correctly according to the external device connected to via the Preference display.
7 COMPONENT VIDEO OUT jacks (Y/P
B
/P
R
) (13)
Output component video signals.
7
EN04-11.XV-521BK[1U] 7 00.6.9, 3:29 PM
Preliminary knowledge
Operational Principles
On-screen displays
The unit provides several on-screen displays.
With some displays, you can set or select preferences or functions, while the others are display-only.
Opening displays
The Opening display appears automatically in some conditions.
At the bottom, the following information are indicated depending on the unit’s status.
• NOW READING: The unit is now reading the disc information (TOC).
• REGION CODE ERROR!: The DVD VIDEO disc loaded cannot be played because the region code of the disc does not match the unit.
• OPEN: The disc tray is now opening.
• CLOSE: The disc tray is now closing.
Preference displays
When the unit is stopped, pressing the RETURN-
CHOICE button while holding the SHIFT button accesses the preference display for setting the preferences.
There are four pages: LANGUAGE, AUDIO, DISPLAY and SYSTEM as shown in the right.
See page 35 for detailed information.
Opening display
NOW READING
LANGUAGE
LANGUAGE AUDIO
MENU LANGUAGE
AUDIO LANGUAGE
SUBTITLE
ON SCREEN LANGUAGE
DISPLAY SYSTEM
ENGLISH
ENGLISH
ENGLISH
ENGLISH
EXIT
PRESS KEY
DISPLAY
LANGUAGE AUDIO
MONITOR TYPE
SCREEN SAVER
ON SCREEN GUIDE
DISPLAY
4:3 LB
OFF
ON
SYSTEM
EXIT
PRESS KEY
AUDIO
LANGUAGE AUDIO
DIGITAL AUDIO OUTPUT
DOWN MIX
COMPRESSION
DISPLAY SYSTEM
/PCM
Lo / Ro
ON
EXIT
PRESS KEY
SYSTEM
LANGUAGE AUDIO
AUTO STANDBY
RESUME
AV COMPULINK MODE
DISPLAY SYSTEM
OFF
OFF
DVD 1
EXIT
PRESS KEY
PARENTAL LOCK displays
When no disc is inserted or a DVD VIDEO disc is stopped, pressing the ENTER button while holding down the SHIFT button accesses the PARENTAL LOCK display in which you can set the level for limiting playback.
See page 39 for detailed information.
PARENTAL LOCK
Country Code
Set Level
PASS WORD
PARENTAL LOCK
US
—
- - - -
EXIT
PRESS KEY ENTER
8
EN04-11.XV-521BK[1U] 8 00.6.9, 3:29 PM
Preliminary knowledge
Play mode displays
Pressing the PLAY MODE button accesses the play mode display in which you can control playback functions.
Different displays appear depending on the disc type and the unit’s status.
While stopped
REPEAT PROGRAM RANDOM
During DVD VIDEO playback
DVD CONTROL
REPEAT A-B REPEAT TIME SEARCH CHAP. SEARCH
During Audio CD playback
CD CONTROL
REPEAT A-B REPEAT TIME SEARCH
During Video CD playback
VCD CONTROL
REPEAT A-B REPEAT TIME SEARCH PBC CALL
Status displays
Pressing the DISPLAY-TIME button during playback accesses the status display.
For a DVD VIDEO disc, pressing the DISPLAY-TIME button toggles between the DVD VIDEO function status display, and the disc/time display and off.
For a Video CD or Audio CD disc, pressing the DISPLAY-
TIME button switches the disc/time display on and off.
DVD VIDEO function status
1 / 2 1 / 2
ENGLISH
1 / 2
ENGLISH
Disc/time (DVD VIDEO )
TITLE
1
CHAP.
25
TIME
2:25:25
BITRATE
3.3
Mbps
Disc/time (Audio CD/Video CD without PBC)
TRACK
1
TIME
00:08 EACH
REMAIN
Disc/time
(Video CD with PBC)
TRACK
1
TIME
25:25 PBC
To prevent the monitor from burning out [SCREEN SAVER]
A television monitor screen may be burned out if a static picture is displayed for a long time. To prevent this, the unit automatically activates the screen saver function if a static picture, such as an on-screen display or menu, is displayed for over 5 minutes.
• Pressing any button on the unit or the remote control unit will release the screen saver function and return to the previous display.
• You can select one of several screen saver modes available (see page 37).
• The screen saver function is not activated during
Audio CD playback or after stopping Audio CD playback.
DVD/Video CD/CD PLAYER
9
EN04-11.XV-521BK[1U] 9 00.6.9, 3:29 PM
Preliminary knowledge
On-screen guide icons
During DVD playback, you may see icons displayed over the picture. These have the following meanings.
: Displayed at the beginning of a scene recorded from multiple angles. (See page 30.)
: Displayed at the beginning of a scene recorded with multiple audio languages. (See page 31.)
: Displayed at the beginning of a scene recorded with multiple subtitle languages. (See page 31.)
You can set the unit not to display on-screen icons above via the preference settings described on page 38.
About invalid operation icon
When you press a button, if the unit does not accept its operation, appears on your television screen. Operations are occasionally unacceptable even if
is not displayed.
Note that some operations may not be accepted. For example, some discs may not allow rapid advance/reverse or slow-motion playback.
How to use numeric buttons
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
To select a track/title number
• To select a number between 1 and 10
Press the corresponding button for the number.
• To select a number higher than 10
Use the +10 button.
Examples:
To select 13
To select 34
To select 40
+10
+10
+10
→
→
→
3
+10
+10
→
→
+10
+10
→
→
4
10
To enter a time or chapter number
The method for entering a time for Time search or chapter number for Chapter search is different from above. See the corresponding sections in this manual for the details.
To select a TV channel.
Press the corresponding numeric buttons (between 0 and 9) while holding down the SHIFT button.
EN04-11.XV-521BK[1U] 10 00.6.9, 3:29 PM
10
Preliminary knowledge
About discs
Playable disc types
Playable and non-playable disc types are as follows:
Playable discs
DVD VIDEO Video CD Audio CD CD-R
CD-RW
The DVD VIDEO Logo is a trademark.
• CD-R and CD-RW discs recorded with the audio CD format can be played back, though some may not be played back because of the disc characteristics or recording condition.
• DVD VIDEO players and DVD VIDEO discs have their own Region Code numbers. This unit only can play back DVD
VIDEO discs whose Region Code numbers include “1”.
Examples of playable DVD VIDEO discs:
ALL 1 1 2
1
3
2
4
This unit accommodates the NTSC television system and can playback discs recorded with the NTSC system. Note that the unit cannot playback discs recorded with the PAL system.
Non-playable discs
DVD-ROM, DVD-RAM, DVD AUDIO, DVD-R, DVD-RW, CD-ROM, PHOTO CD, CD-EXTRA, CD-G, CD-TEXT
• Playing back discs listed as “Non-playable discs” above may generate noise and damage speakers.
• This unit can play back audio recorded in CD-G, CD-EXTRA and CD-TEXT discs.
Disc structure
A DVD VIDEO disc is comprised of “titles,” while an Audio CD, Video CD is comprised of “tracks.” Each title may be divided into some “chapters.” For example, if a DVD VIDEO disc contains some movies, each movie may have its own title number, and each movie may be divided into some chapters. In a DVD VIDEO karaoke disc, each song usually has its own title number and does not have chapters. In general, each title has independent content, while each chapter in the same title has continuity.
(Example: DVD VIDEO disc)
Title 1 Title 2
Chapter 1 Chapter 2 Chapter 3 Chapter 1 Chapter 2
(Example: Audio CD/Video CD)
Track 1 Track 2 Track 3 Track 4
11
EN04-11.XV-521BK[1U] 11 00.6.9, 3:29 PM
Getting started
Connections
*In the following description, “TV” may be substituted with “monitor” or “projector.”
*Before using the unit, you have to connect the unit to a TV and/or amplifier.
Getting started
Before making any connections
• Do not connect the AC power cord until all other connections have been made.
• Since different components often have different terminal names, carefully read the instructions supplied with the component you are going to connect.
To connect to a TV
You can enjoy using the unit by simply connecting it to a TV. To improve audio sound quality, connect the audio outputs to your separate audio equipment. (See the following pages.)
The unit
DIGITAL OUT
PCM/STREAM
COAXIAL
OPTICAL
Y
VIDEO OUT
COMPONENT
P
B
P
R
S-VIDEO VIDEO
R L
AUDIO OUT
AV COMPU LINK
Yellow
Red
White
* If the TV has an AV COMPU LINK terminal, you can use the AV COMPU LINK function
See “AV COMPU LINK remote control system” on page 41 for details.
S-video cable
(supplied)
Yellow
White
Red
TV
IN
S-VIDEO
VIDEO
LEFT
RIGHT
AUDIO
Audio/video cable
(supplied)
Connect the unit to a TV equipped with stereo audio input and video input jacks using the supplied audio/video cables.
• If your TV has a monaural audio input instead of stereo, you need to use an optional audio cable which converts stereo audio output to monaural.
• If your TV has an S-video input, you should connect it with the S-VIDEO output of the unit using the supplied Svideo cable in addition to the (standard) video connection to get better picture quality.
NOTES
• Connect VIDEO OUT of the unit directly to the video input of your TV. Connecting VIDEO OUT of the unit to a TV via a VCR may cause a monitor problem when playing back a copy-protected disc.
• Connect the unit to an NTSC television. Do not connect the unit to a PAL television.
12
EN12-16.XV-521BK[1U] 12 00.6.9, 3:29 PM
XV-521BK [1U] EN
LVT0435-011A
Getting started
To connect to a TV with the component video input jacks
You can enjoy high picture quality by connecting the unit’s COMPONENT VIDEO OUT jacks to the COMPONENT
VIDEO IN jacks of your TV with the video cables.
Green Blue
Component video cable (not supplied)
Red
The unit
DIGITAL OUT
PCM/STREAM
COAXIAL
OPTICAL
Y
VIDEO OUT
COMPONENT
P
B
P
R
S-VIDEO VIDEO
R L
AUDIO OUT
Red White
AV COMPU LINK
S-video cable
(supplied)
TV
Green
Blue
Red
White
IN
S-VIDEO
VIDEO
LEFT
RIGHT
AUDIO
Y P B P R
IN
Red
Audio cable
(not supplied)
• Connect “Y” to “Y,” “P
B
” to ”P
B
,” and “P
R
” to “P
R
” correctly.
NOTES
• When the component video input jacks of the TV are of the BNC type, use an adapter to convert the pin jacks to BNC jacks
(optional).
• If you do not connect the unit with the S-video cable, some functions of your TV may not work.
• Connect the unit to an NTSC television. Do not connect the unit to a PAL television.
13
To connect to an audio amplifier or receiver
You can enjoy high-quality audio by connecting the unit's audio output to your amplifier or receiver.
The unit
DIGITAL OUT
PCM/STREAM
COAXIAL
OPTICAL
Y
VIDEO OUT
COMPONENT
P
B
P
R
S-VIDEO VIDEO
R L
AUDIO OUT
AV COMPU LINK
Red White
White
Amplifier or receiver
IN
LEFT
RIGHT
AUDIO
Red
Audio cable
(not supplied)
• Connect the unit's AUDIO OUT to any line-level inputs (such as AUX, DVD, CD, etc.) of an audio amplifier or receiver.
EN12-16.XV-521BK[1U] 13 00.6.9, 3:29 PM
Getting started
To connect to audio equipment with a digital input
You can enhance the sound quality by connecting the unit’s DIGITAL OUT to the digital input of an amplifier, DAT or
MD by using an optional digital cable. The digital audio signal from a disc is directly transferred. If you connect the unit to a Dolby Digital or DTS decoder or an amplifier with a built-in decoder by using an optional digital cable, you can enjoy high-quality surround sound.
When you make the digital connection, also make the analog connection, because, depending on the disc type, no audio may be reproduced from the DIGITAL OUT.
When using the DIGITAL OUT (OPTICAL) jack, remove the protection cap. Do not lose the removed cap.
When the DIGITAL OUT (OPTICAL) jack is not used, fix the protection cap into the jack.
Optical digital cable
(not supplied)
Coaxial digital cable
(not supplied)
The unit
DIGITAL OUT
PCM/STREAM
COAXIAL
OPTICAL
Y
VIDEO OUT
COMPONENT
P
B
P
R
S-VIDEO VIDEO
R L
AUDIO OUT
Red
AV COMPU LINK
White
Audio cable
(not supplied)
White
Digital equipment
IN
LEFT
RIGHT
AUDIO
Red
IN
OPTICAL
DIGITAL
COAXIAL
NOTES
• When you connect the unit's DIGITAL OUT to digital audio equipment, before using, make the “DIGITAL AUDIO OUTPUT” setting in the “AUDIO” page of the preference display correctly according to the connected audio equipment. If the “DIGITAL
AUDIO OUTPUT” is not set correctly, loud noise may be generated from speakers, causing damage to your speakers. See
“DIGITAL AUDIO OUTPUT” on page 36.
• With the digital connection, the unit’s settings for COMPRESSION and DOWN MIX in the AUDIO page of the preference display are invalid. Settings for these items must be made from the decoder.
To connect the power cord
When all the audio/video connections have been made, insert the smaller plug of the supplied AC power cord to the unit’s AC IN connector, then insert the other end to the wall outlet. Make sure that plugs are inserted firmly. The
STANDBY indicator lights and setup is completed.
Warning
• Disconnect the power cord if you are not going to use the unit for a long time.
• Disconnect the power cord before cleaning the unit.
• Disconnect the power cord before moving the unit.
• Do not connect or disconnect the power cord with wet hands.
• Do not pull the power cord when disconnecting it, as this may damage the cord and cause fire, electric shock, or other accidents.
Caution
• Do not damage, alter, twist, or pull the power cord, as this may cause fire, electric shock, or other accidents.
• To prevent any accidents or damages caused by an unsuitable AC power cord, only use the supplied power cord. If the cord is damaged, contact a dealer and get the new power cord.
• Do not put anything heavy, or the unit, on the power cord, as this may cause fire, electric shock, or other accidents.
14
EN12-16.XV-521BK[1U] 14 00.6.9, 3:30 PM
XV-521BK [1U] EN
LVT0435-011A
Getting started
Using the remote control unit
Using the remote control, you can operate not only all the functions of the unit but also basic functions of your TV.
To install batteries in the remote control unit
The battery compartment is located on the back of the remote control unit.
1
Press down on the point shown by the arrow at the top of the compartment cover, and pull up the cover to open the compartment.
2
Place the two accessory R6P (SUM-3)/AA(15F) batteries in the remote control according to the polarity markings (“+” and “–”) inside the compartment and on the batteries.
3
Place the cover over the compartment, and press down lightly.
• The batteries will last about six months with normal use. If the functions of the remote control become erratic, replace the batteries. See below for more information.
Precautions for the safe use of batteries
Observe the following precautions for the safe use of batteries. If they are used improperly their life will be shortened, they may burst or their contents may leak.
Precaution
• Remove the batteries from the remote control if it is not going to be used for a long period of time.
• Remove dead batteries and dispose of them properly.
• Never leave dead batteries lying around, take them apart, mix them with other refuse, or throw them into an incinerator.
• Never touch liquid that has leaked out of a battery.
• Do not mix new and old batteries, or batteries of different types, when replacing them.
15
EN12-16.XV-521BK[1U] 15 00.6.9, 3:30 PM
Getting started
To use the remote control unit for TV operation
You can operate your TV from the remote control unit.
Setting the remote control signal for operating your TV.
1
Holding down TV/VIDEO, enter the manufacturer code of your TV listed below by using the numeric buttons (0 - 9).
Do not release TV/VIDEO. Keep holding it until the next step is completed.
Manufacturer code list
No.
Manufacturer
01 JVC
06
07
08
09
02
03
04
05
MAGNAVOX
MITSUBISHI
PANASONIC
RCA
SHARP
SONY
TOSHIBA
ZENITH
12
13
14
15
No.
Manufacturer
10
11
HITACHI
PANASONIC
SAMSUNG
SANYO
SANYO
SAMSUNG
Example:
To enter the manufacturer code “01”:
Press “0” then “1.”
2
Press 7 (STOP) while holding down TV/VIDEO.
The following buttons can be used for operating the TV:
TV POWER
DVD POWER
Turns the TV on or off.
SHIFT
TV ch
Changes the TV channels.
TV
VOL
Adjusts the TV volume.
SHIFT
1
TV 1
0
TV 0 to 9
TV 9
+10
TV 100+
SHIFT
10
TV RETURN
TV/VIDEO
Selects the TV channels.
*For some TVs, pressing “+10” while holding down SHIFT functions as the “100+.” “+10” functions as the ENTER button if your TV requires pressing the ENTER button after selecting a channel number.
Returns to the previously selected channel (only valid for JVC
TVs).
Switches input mode (either TV or VIDEO).
3
Try to operate your TV by pressing DVD POWER - TV POWER while holding SHIFT.
If your TV turns on or off, you have successfully set the control signal.
NOTES
• The remote control unit is initially set for operating a JVC TV.
• If there is more than one code listed for the manufacturer of your TV, try them one by one until you succeed.
To control the volume of a JVC’s amplifier or receiver
You can control the volume of a JVC’s amplifier or receiver by using the AMP VOL button on the remote control unit.
AMP
VOL
16
EN12-16.XV-521BK[1U] 16 00.6.9, 3:30 PM
Basic operations
Basic operations
In the following description, the buttons on the remote control unit are mainly used, however, you may use the corresponding buttons on the front panel of the unit if available.
Turning on/off the unit
Press POWER on the front panel or press DVD POWER - TV POWER on the remote control unit.
POWER
POWER
DVD PLAYER
STANDBY
3D PHONIC TITLE CHAP.
EACH
RESUME THEATER
OPEN/CLOSE
0
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
PLAY MODE DISPLAY RETURN
SHIFT
B.SEA
RCH
CANCEL
PLAY
3
TIME CHOICE
F.SEARC
H
8
E
ENTER
MENU
TITLE
UP
LEFT
CURSOR
DOWN
RIGHT
DVD POWER
TV POWER
• You can turn on the unit by pressing the PLAY button on the front panel or the remote control unit. In this operation, the unit starts playback if the disc is set in the disc tray. If no disc is set, the disc tray opens.
• You can also turn on the unit by pressing the OPEN/CLOSE button on the front panel or the remote control unit. In this case, the disc tray opens.
REMOTE CONTROL
NOTE
Even if you press the POWER or DVD POWER - TV POWER button to turn off the unit, the unit is not disconnected from the AC power source as long as it is connected to the wall outlet. This state is called the standby mode. In this state, the unit is designed to consume a very small quantity of power.
Inserting and removing discs
1
Press OPEN/CLOSE to open the disc tray.
2
Place the disc in the tray.
With the label side up
WE
R
PLA
DVD
YE
R
ST
AN
DB Y
3D
IC
PH ON
C
DIS
LE
TIT
CH AP
EA
CH
RE
SU ME
TH
EA TE
R
EN
OP
E
/CL
OS
0 ST 7
OP
US
8
E
SK
IP
¢
4
D /
DV
CD
/ C
VD
EO
D
• To insert an 8-cm disc, place it in the inner recess.
3
Press OPEN/CLOSE to close the disc tray.
NOTES
• The unit can playback DVD VIDEO, Audio CD, and Video CD discs only. Do not load other disc types. For details about playable disc types, see page 11.
• When loading a disc in the tray, be sure to position the disc inside the recess. Otherwise, the disc may be damaged when the tray is closed, and the disc may not be removed from the unit.
17
EN17-19.XV-521BK[1U] 17 00.6.9, 3:30 PM
XV-521BK [1U] EN
LVT0435-011A
Basic operations
Basic playback
Now you can play a disc. First, let’s enjoy simple playback according to following procedure.
To start playback
Press PLAY.
The unit starts playback from the beginning.
NOTES
• During playback, the display window shows the title/chapter or track number being played.
• With Video CD discs with PBC control or some DVD discs, the menu display may appear on the TV screen after starting playback. In such a case, select an item to be played back from the menu.
For operation using a menu, see page 20.
• With some DVD discs, the unit starts playback automatically after inserting the disc.
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
PLAY MODE DISPLAY RETURN
SHIFT
B.SEA
RCH
CANCEL
PLAY
3
TIME CHOICE
F.SEARC
F.SKIP
H
¢
8
E
ENTER
MENU
TITLE
LEFT
UP
CURSOR
RIGHT
DOWN
Basic control buttons
REMOTE CONTROL
To stop playback completely
Press STOP.
The unit stops playback.
To stop playback temporarily
Press PAUSE.
The unit pauses playback. To continue playback, press PLAY.
To advance or reverse playback rapidly while monitoring
7
During playback
From the remote control unit
Hold down 4 or ¢.
Holding down ¢ advances playback rapidly, while holding down 4 reverses playback at 5 times the normal speed.
Releasing the button returns the unit to normal playback.
or
Press 4 or ¢ while holding down the SHIFT button.
Each press of 4 or ¢ while holding down the SHIFT button increases the playback speed from 2x to 60x the normal speed.
Pressing PLAY returns the unit to normal playback.
From the front panel
Use the SHUTTLE knob.
To advance playback rapidly, turn the shuttle knob to the right and hold, and to reverse play rapidly, turn the shuttle knob to the left and hold. By releasing the shuttle knob, the unit returns to normal playback. The playback speed changes according to the amount you turn the shuttle knob.
LE CHAP.
EACH
RESUME THEATER
OPEN/CLOSE
0
4
SKIP
¢
SHUTTLE knob
1
SHUTTLE
¡
DVD / VDEO CD / CD
Holding down the 4 or ¢ button on the front panel also advances or reverses playback rapidly.
18
EN17-19.XV-521BK[1U] 18 00.6.9, 3:30 PM
Basic operations
To locate the beginning of the scene or song
7
During playback
Press 4 or ¢.
Press 4 to locate the beginning of the current chapter, title, or track, and press ¢ to locate the beginning of the next chapter, title, or track.
NOTE
When you play a Video CD disc with the PBC function or a DVD VIDEO disc, the unit may locate a different place, but it will generally locate the beginning of the title or chapter or track.
To resume playback
The unit can memorize the position on a disc where you interrupt playback, and resume playback from that position next time you press PLAY.
To memorize the interrupted position
1
Set the RESUME setting on the SYSTEM page of the preference display to ON.
(See page 38 for details about how to set.)
2
At the position you want to interrupt playback, press STOP, or press DVD POWER - TV POWER on the remote control or POWER on the front panel.
The unit memorizes the interrupted position, while [RESUME] lights in the display window.
If you interrupt playback by pressing STOP in step 2 above and then turn off the power, the memory is not cleared.
To resume playback
7
While the disc you interrupt playback last time is still in the disc tray.
Press PLAY.
The unit starts playback from the position where you interrupted playback last time.
¶ To clear the resume position memory
Operate one of the followings:
* Take out the disc from the tray
* Press STOP while stopped
* Turn on the unit by pressing DVD POWER - TV POWER (on the remote control) or POWER (on the front panel).
NOTES
• Do not press POWER (on the front panel) or DVD POWER - TV POWER (on the remote control) to turn on the unit if you want to resume playback, which will clear the resume position memory.
• The resume function does not work with Audio CD discs.
• The resume function does not work if RESUME on the SYSTEM page of the preference display is set to OFF.
• In the case of a Video CD disc with PBC function, the unit may resume playback from a point slightly earlier than the resume point you stored.
• The resume function does not work in the program or random mode.
19
EN17-19.XV-521BK[1U] 19 00.6.9, 3:30 PM
XV-521BK [1U] EN
LVT0435-011A
Advanced operations
Playing from a specific position on a disc
You can play a disc from the selected track, title or chapter, or from the specified time.
To locate a desired scene from the DVD menu
DVD VIDEO discs generally have their own menus which show the disc contents. These menus contain various items such as titles of a movie, names of songs, or artist information, and display them on the
TV screen. You can locate a desired scene by using the menu.
1
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
PLAY MODE DISPLAY RETURN
SHIFT
B.SEA
RCH
8
CANCEL
STOP
7
TIME CHOICE
F.SEARC
F.SKIP
H
¢
ENTER
MENU
TITLE
LEFT
UP
CURSOR
RIGHT
DOWN
2
REMOTE CONTROL
Advanced operations
NOTES
• When appears on the TV screen by pressing TITLE in step 1:
The disc does not have a menu listing the titles.
• When appears on the TV screen by pressing MENU in step 1:
The disc does not have a menu
• The menu button does not work while stopped.
To locate a desired scene from the menu of the Video CD with PBC
Some Video CD discs are compatible with the PBC function. PBC is an abbreviation of “PlayBack Control.”
A Video CD disc recorded with PBC has its own menus, such as a list of the songs of the disc and items recorded on the disc. You can also locate a specific scene by using the menu.
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
PLAY MODE DISPLAY RETURN
SHIFT
B.SEA
RCH
B.SKIP
4
PAUS
E
8
CANCEL
PLAY
3
TIME CHOICE
F.SEARC
H
ENTER
MENU
TITLE
LEFT
UP
CURSOR RIGHT
DOWN
REMOTE CONTROL
2
1
7
Whenever a DVD VIDEO disc is loaded
1
Press MENU or TITLE.
The menu appears on the TV screen.
About menu
Normally, a DVD VIDEO disc which contains more than one title may have a “title” menu which lists the titles. In this case, the menu appears on the
TV screen by pressing the
TITLE button. Some DVD
VIDEO discs may also have a different menu which appears by pressing the MENU button.
Example
See the instructions of each DVD VIDEO disc for its particular menu.
2
Use CURSOR 2/3/5/∞ to select a desired item, then press ENTER.
The unit starts playback of the selected item.
7
When a Video CD disc with PBC is stopped
1
Press PLAY.
A disc menu appears on the TV screen (The PBC function is activated).
Example:
“Pbc” is indicated in the display window on the front panel.
2
Use the numeric buttons to select the desired number of the item.
• See page 10 for details about how to use the numeric buttons.
Playback starts from the selected item.
You can return to the menu by pressing RETURN -
CHOICE.
With some discs, you can also select items by entering the corresponding number using the numeric buttons, which may cause the unit to automatically start playback.
20
EN20-34.XV-521BK[1U] 20 00.6.9, 3:30 PM
XV-521BK [1U] EN
LVT0435-011A
Advanced operations
When “NEXT” or “PREVIOUS” appears on the TV screen, the unit generally works as follows:
• Pressing ¢ advances to the next page.
• Pressing 4 returns to the previous page.
* The method of the operation is different depending on the disc.
NOTES
• When appears on the TV screen.
The title or track you have specified is not contained in the disc.
• This function does not work during Video CD playback with PBC function
21
• To activate the PBC function when a PBC-compatible Video
CD disc is being played back without the PBC function, press STOP then press PLAY.
• You can also activate the PBC function using the play mode menu display as follows.
1.
Press PLAY MODE - CANCEL.
2.
Use the CURSOR 2/3 to move to [PBC CALL], then press ENTER.
• If you want to playback a PBC-compatible Video CD disc without activating the PBC function, start playback by using the numeric buttons instead of the PLAY button. See the next paragraph.
To locate a desired selection using the numeric buttons
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
SHIFT
PLAY MODE DISPLAY RETURN
CANCEL TIME CHOICE
B.SEA
RCH
B.SKIP
4
PAUS
E
8
PLAY
3
ENTER
MENU
TITLE
LEFT
UP
CURSOR RIGHT
DOWN
1
REMOTE CONTROL
You can play a desired title (DVD VIDEO) or track
(Audio CD/Video CD) by specifying the number.
7
For DVD VIDEO: While stopped
For Audio CD: Whenever an Audio CD disc is loaded
For Video CD: During playback without PBC function or while stopped
1
Use the numeric buttons to specify the desired title or track number.
The unit starts playback from the selected title or track.
• See page 10 for details about how to use the numeric buttons.
The selected title or track number appears in the display window on the front panel.
Display window
TITLE
TRACK
To locate a desired selection using 4 or ¢
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
SHIFT
PLAY MODE DISPLAY RETURN
CANCEL TIME CHOICE
PLAY
3
8
E
ENTER
MENU
TITLE
LEFT
UP
CURSOR RIGHT
DOWN
REMOTE CONTROL
1
7
For DVD VIDEO: During playback
For Audio CD: During playback
For Video CD: During playback without PBC function
1
Press 4 or ¢.
With an Audio CD or Video CD, pressing the button skips a track. With a DVD VIDEO disc, pressing the button skips a chapter or title depending on the disc configuration.
The selection number appears in the display window on the front panel.
• To locate a subsequent selection, press ¢ once or repeatedly until the desired selection number appears in the display.
• To locate to beginning of the current selection, press 4 once.
• To locate a former selection, press 4 repeatedly until the desired selection number appears in the display.
NOTES
• This function may not work with some DVD VIDEO discs.
• This function does not work during Video CD playback with PBC function
EN20-34.XV-521BK[1U] 21 00.6.9, 3:30 PM
XV-521BK [1U] EN
LVT0435-011A
To locate a desired scene by specifying the chapter number [CHAP. SEARCH]
If the current title of a DVD VIDEO disc being played is divided into chapters, you can skip to a desired chapter by specifying the chapter number using the on-screen display.
1
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
SHIFT
PLAY MODE DISPLAY RETURN
CANCEL TIME CHOICE
B.SEA
RCH
B.SKIP
4
PLAY
3
8
ENTER
MENU
TITLE
LEFT
UP
CURSOR RIGHT
DOWN
3
4
2
REMOTE CONTROL
7
During DVD VIDEO playback
1
Press PLAY MODE - CANCEL.
The DVD play mode menu appears on the TV screen.
2
Use CURSOR 2/3 to move to [CHAP.
SEARCH], then press ENTER.
“GO TO CHAPTER = ” appears under the menu.
DVD CONTROL
REPEAT A-B REPEAT TIME SEARCH CHAP. SEARCH
GO TO CHAPTER =
Advanced operations
NOTES
• When the chapter number is incorrect in step 3:
Overwrite the incorrect number with the correct number.
• When is displayed in the TV screen in step 4:
The chapter you have selected is not contained in the disc, or chapter search does not work on the disc.
• With some discs, the unit automatically starts searching for the chapter after entering the chapter number in step
3.
• To turn off the play mode menu:
Press PLAY MODE.
To locate a desired position in the current title or track [TIME SEARCH]
You can play a disc from the desired position by specifying the elapsed time from the beginning of the current title or track using the TIME SEARCH function.
Note that some DVD VIDEO discs do not contain time information, and the TIME SEARCH function cannot be used.
1
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
PLAY MODE DISPLAY RETURN
SHIFT
CANCEL
B.SEA
RCH
PLAY
3
TIME CHOICE
F.SEARC
F.SKIP
H
¢
8
TITLE
ENTER
MENU
LEFT
UP
CURSOR
RIGHT
DOWN
3
4
2
REMOTE CONTROL
3
Use the numeric buttons (0 ~ 9) to enter the desired chapter number.
Example:
To select chapter number 8:
Press “8”
→
ENTER.
To select chapter number 37:
Press “3”
→
“7”
→
ENTER.
4
Press ENTER.
The unit starts playback from the selected chapter.
The “10” and “+10” buttons are not used in this function.
7
For DVD VIDEO: During playback
For Audio CD: During playback
For Video CD: During playback without PBC function
1
Press PLAY MODE - CANCEL.
The play mode menu appears on the TV screen.
2
Use CURSOR 2/3 to move to [TIME
SEARCH], then press ENTER.
“GO TO” appears under the menu.
3
Use the numeric buttons (0 ~ 9) to enter the time.
You can specify the elapsed time of the current title or track to set the location which you want to playback from.
22
EN20-34.XV-521BK[1U] 22 00.6.9, 3:30 PM
XV-521BK [1U] EN
LVT0435-011A
Advanced operations
4
Press ENTER.
The unit starts playback from the specified time.
(for DVD VIDEO)
DVD CONTROL
REPEAT A-B REPEAT TIME SEARCH CHAP. SEARCH
(for Audio CD)
CD CONTROL
REPEAT A-B REPEAT TIME SEARCH
GO TO 2 : 3 4 : 0 0 GO TO 0 2 : 3 4
Selected time
• “10” and “+10” buttons are not used in this function.
• You can specify the time in hour/minute/second format for DVD VIDEO discs, and in minute/second format for Audio and Video CD discs.
Selected time
(for Video CD)
VCD CONTROL
REPEAT A-B REPEAT TIME SEARCH PBC CALL
GO TO 0 2 : 3 4
Selected time
Example (for DVD VIDEO):
To playback from 2(H):34(M):00(S)
GO TO _ : _ _ : _ _
Press “2”.
GO TO 2 : _ _ : _ _
Press “3”.
GO TO 2 : 3 _ : _ _
Press “4”.
GO TO 2 : 3 4 : _ _
Press ENTER.
You do not have to press “0” to enter the trailing zeros
(for the last two digits in the example above). Of course, it is possible to enter them.
• When you make a mistake
Move the cursor to the incorrect value, then press the correct button to re-select the value.
23
GO TO 2 : 3 5 : _ _
Press CURSOR 2.
GO TO 2 : 3 _ : _ _
Press “4”.
GO TO 2 : 3 4 : _ _
NOTES
• When appears on the TV screen in step 2:
The time you have selected is not contained on the disc, or the time search function does not work on the disc.
Also note that the time search function does not work during Video CD playback with the PBC function.
• To turn off the play mode menu:
Press PLAY MODE.
• The TIME SEARCH function cannot be used during program playback.
To locate a desired scene from the digest display [DIGEST]
The unit can display the opening scene of each title or chapter on a DVD VIDEO or each track of a Video CD.
You can select a desired scene from those displayed on the TV screen.
1
2
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO
ANGLE
TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
PLAY MODE DISPLAY RETURN
SHIFT CANCEL TIME CHOICE
F.SEARC
F.SKIP
H
¢
8
E
ENTER
TITLE
MENU
LEFT
UP
CURSOR
RIGHT
DOWN
REMOTE CONTROL
3
7
For DVD VIDEO: While stopped or during playback
For Video CD: While stopped or during playback without PBC function.
1
Press SUBTITLE - DIGEST while holding down SHIFT.
Up to nine opening scenes are displayed.
• While a DVD VIDEO disc is stopped:
The opening scene of each title appears on the
TV screen.
• During DVD VIDEO disc playback:
The opening scene of each chapter in the current title appears on the TV screen.
• When a Video CD disc is loaded:
The opening scene of each track appears on the
TV screen .
2
Use CURSOR 2/3/5/∞ to select the desired scene.
The selected scene is indicated by .
If there are more than 9 scenes, the digest screen will have more than one page. In this case, pressing ¢ advances to the next page, while pressing 4 returns to the previous page.
EN20-34.XV-521BK[1U] 23 00.6.9, 3:30 PM
XV-521BK [1U] EN
LVT0435-011A
Selected scene
• When the lower right scene is selected, pressing CURSOR
3 advances to the next page if available. Similarly, when the upper left scene is selected, pressing CURSOR
2 returns to the previous page (if available).
• When there are more than one digest page, after pressing
SUBTITLE - DIGEST while holding down SHIFT, pressing
¢ before all 9 scenes of the first page appear on the TV screen will advance to the next page. Similarly, pressing
4 before all the scenes of the second or latter page appear on the TV screen will return to the previous page.
3
Press ENTER.
The unit starts playback from the selected title or track.
NOTE
With some discs, depending on the contents, it may take some time until all the scenes appear on the screen.
Advanced operations
Special picture playback
The unit provides special picture playback functions including Frame-by-frame, Strobe, Slow-motion and
Zoom.
To advance a still picture frame-by-frame
1
PLAY MODE DISPLAY RETURN
SHIFT CANCEL
B.SEA
RCH
TIME CHOICE
F.SEARC
F.SKIP
H
¢
8
E
ENTER
TITLE
MENU
LEFT
UP
CURSOR
RIGHT
DOWN
REMOTE CONTROL
7
While paused (still)
1
Press PAUSE.
Each time you press PAUSE, the still picture advances to the next frame.
Pressing PLAY returns to the normal playback mode.
To display still pictures [STROBE]
2
1
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
PLAY MODE DISPLAY RETURN
CHOICE
SHIFT
CANCEL
B.SEA
RCH
PLAY
3
TIME
8 ENTER
MENU
TITLE
LEFT
UP
CURSOR
RIGHT
DOWN
REMOTE CONTROL
7
During playback
1
At the point you want to view as continuous photographs, press PAUSE.
The unit pauses playback.
2
Press AUDIO - STROBE while holding down
SHIFT.
Nine continuous still pictures appear on the TV screen.
• Pressing PAUSE when the nine still pictures appear will advance to the next nine still pictures.
24
00.6.9, 3:30 PM EN20-34.XV-521BK[1U] 24
XV-521BK [1U] EN
LVT0435-011A
Advanced operations
• To cancel strobe play
Press AUDIO - STROBE while holding down SHIFT.
NOTES
• Pressing and holding PAUSE for more than 1 second also activates the Strobe function.
• If you press AUDIO - STROBE while holding down SHIFT during playback, nine still pictures also appear but they advance in realtime.
To playback in slow-motion [SLOW]
7
During playback
From the remote control unit
1
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO
ANGLE
TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
PLAY MODE DISPLAY RETURN
SHIFT CANCEL
B.SEA
RCH
TIME CHOICE
F.SEARC
F.SKIP
H
¢
8
E
ENTER
TITLE
MENU
LEFT
UP
CURSOR
RIGHT
DOWN
REMOTE CONTROL
1
Press SLOW.
To play forward slow-motion, press SLOW “+“, and to play reverse slow-motion (for DVD VIDEO discs only), press SLOW “–“. First, the unit plays the slowest speed, and each time you press the button, the playback speed increases.
From the front panel
OPEN/CLOSE
0
1
SHUTTLE
¡
CHAP.
EACH
RESUME THEATER
4
SKIP
¢
DVD / VDEO CD / CD
1
1
Press PAUSE, then use the SHUTTLE knob.
To play forward slow-motion, turn the SHUTTLE knob to the right. To play reverse slow-motion (for
DVD VIDEO discs only), turn it to the left. The more you turn the knob, the more the slowmotion speed increases.
• To return to normal playback
Press PLAY.
• To pause slow-motion playback
Press PAUSE.
NOTES
• The sound is muted during slow-motion playback.
• Reverse slow-motion playback is not possible for a Video
CD.
25
EN20-34.XV-521BK[1U] 25 00.6.9, 3:30 PM
XV-521BK [1U] EN
LVT0435-011A
To zoom a scene [ZOOM]
1
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
SHIFT
PLAY MODE DISPLAY RETURN
CANCEL TIME CHOICE
B.SEA
RCH
B.SKIP
4
PAUS
E
8
PLAY
3
ENTER
MENU
TITLE
LEFT
UP
CURSOR RIGHT
DOWN
REMOTE CONTROL
2
7
During playback or while paused
1
Press ANGLE - ZOOM while holding down
SHIFT.
“ZOOM” appears on the TV screen.
The unit zooms in to the center part of the scene to produce a double-sized image.
ZOOM
2
Use CURSOR 2/3/5/∞ to move the zoomed-in scene.
ZOOM
• To pause zoom play
Press PAUSE.
To resume zoom play, press PLAY.
• To return to normal playback
Press ANGLE - ZOOM while holding down SHIFT.
NOTE
During Zoom play, the picture may be garbled or noisy.
EN20-34.XV-521BK[1U] 26
Advanced operations
Changing the playback order
You can play titles or tracks in the desired order or in random order.
To playback in the desired order
[PROGRAM]
You can play titles or tracks in the desired order by using the Program function.
1
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
PLAY MODE DISPLAY RETURN
CHOICE
SHIFT
CANCEL
B.SEA
RCH
PLAY
3
TIME
8 ENTER
MENU
TITLE
LEFT
UP
CURSOR
RIGHT
DOWN
REMOTE CONTROL
3
4
2
7
While stopped
1
Press PLAY MODE - CANCEL.
The play mode menu appears on the TV screen.
2
Use CURSOR 2/3 to move to
[PROGRAM] and press ENTER.
REPEAT PROGRAM RANDOM
1
7
13
2
8
14
3
9
15
4
10
16
5
11
17
6
12
18
The program table appears under the menu bar
(as shown above).
The “PROGRAM” indicator appears in the display window on the front panel.
3
Select the titles or tracks in the desired order using the numeric buttons.
See page 10 for details about how to use the numeric buttons.
Up to 18 titles or tracks can be programmed. You may select the same title or track more than once.
1
3
7
13
2
20
8
14
3
1
9
15
4
15
10
16
5
11
17
6
12
18
The programmed title/track number is shown under each program number.
26
00.6.9, 3:30 PM
XV-521BK [1U] EN
LVT0435-011A
Advanced operations
• When you specify a wrong selection
Press PLAY MODE - CANCEL while holding down the SHIFT. The last selection programmed is erased.
• To clear the program
Press STOP.
4
Press PLAY to start program play.
When all of the programmed titles/tracks have finished playback, the unit stops but the program remains.
NOTES
• Some DVD VIDEO discs may not be played back correctly in program mode.
• During program playback, pressing
¢ skip to the next selection of the program. Pressing
4 returns to the beginning of the current selection, however, you cannot skip back to the previous selection.
• By pressing PLAY MODE - CANCEL during program playback, the program table is displayed on the TV screen and the current program number is indicated in yellow.
• To quit program playback
Press STOP and press STOP again.
The “PROGRAM” indicator in the display window turns off and the program is cleared.
While stopped and the play mode menu is displayed on the TV screen, by moving to [PROGRAM] and pressing ENTER, the program mode quits. Note that the program remains.
To playback in random order [RANDOM]
You can play titles or tracks in random order by using the Random function.
1
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
SHIFT
PLAY MODE DISPLAY RETURN
CANCEL TIME CHOICE
B.SEA
RCH
B.SKIP
4
PLAY
3 F.SKIP
¢
8
ENTER
MENU
TITLE
LEFT
UP
CURSOR RIGHT
DOWN
3
2
REMOTE CONTROL
7
While stopped
1
Press PLAY MODE - CANCEL.
The play mode menu appears on the TV screen.
2
Use CURSOR 2/3 to move to
[RANDOM].
REPEAT PROGRAM RANDOM
The “RANDOM” indicator appears in the display window on the front panel.
3
Press ENTER.
The unit starts random playback.
After playing all titles/tracks of the disc, random playback ends.
The same title or track will not be played back more than once during random play.
• To stop/quit random playback in the middle
Press STOP to stop playback. The unit is still in random playback mode, so pressing PLAY starts random playback again.
To quit random playback, press STOP again while stopped. The “RANDOM” indicator in the display window turns off.
NOTE
Some DVD VIDEO discs may not be played back correctly in random mode.
27
EN20-34.XV-521BK[1U] 27 00.6.9, 3:30 PM
XV-521BK [1U] EN
LVT0435-011A
Advanced operations
Repeat playback
You can repeat playback of the current selection or all disc contents. You can also repeat playback of a desired part.
To repeat the current selection or all disc contents [REPEAT]
1
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
PLAY MODE DISPLAY RETURN
CHOICE
SHIFT
CANCEL
B.SEA
RCH
PLAY
3
TIME
8
E
ENTER
MENU
TITLE
LEFT
UP
CURSOR
RIGHT
DOWN
REMOTE CONTROL
2
• For Audio/Video CD
(for Audio CD)
CD CONTROL
REPEAT A-B REPEAT TIME SEARCH
REPEAT ALL
(for Video CD)
VCD CONTROL
REPEAT A-B REPEAT TIME SEARCH PBC CALL
REPEAT ALL
Selected repeat mode Selected repeat mode
REPEAT ALL (all track repeat)
REPEAT 1 (current track repeat)
No indication
(off)
• To stop repeat playback
Press STOP.
7
In any condition except Video CD playback with PBC
1
Press PLAY MODE - CANCEL.
The play mode menu appears on the TV screen.
2
Use CURSOR 2/3 to move to [REPEAT], then press ENTER.
Each time you press ENTER, the repeat mode changes as follows:
• For DVD VIDEO
DVD CONTROL
REPEAT A-B REPEAT TIME SEARCH CHAP. SEARCH
REPEAT ALL
• If you press STOP in REPEAT ALL mode, the unit stops playback but remains in the mode.
• If you press STOP in REPEAT1, TITLE REPEAT or CHAPTER
REPEAT mode, the unit stops playback and quits the mode.
• To quit repeat playback
With pointed at [REPEAT], press ENTER repeatedly until the mode is set to off.
NOTES
• Some DVD VIDEO discs do not allow the title repeat or/ and chapter repeat.
• Some DVD VIDEO discs automatically stops playback in the middle of the disc.
• Repeat playback function cannot be used during Video
CD playback with PBC function.
• To turn off the play mode menu display
Press PLAY MODE - CANCEL.
The selected repeat mode appears on the TV screen.
REPEAT ALL (all title repeat)
* REPEAT TITLE (current title repeat)
* REPEAT CHAPTER (current chapter repeat)
No indication (off)
* While stopped, you cannot select REPEAT TITLE or
REPEAT CHAPTER.
28
EN20-34.XV-521BK[1U] 28 00.6.9, 3:30 PM
XV-521BK [1U] EN
LVT0435-011A
Advanced operations
To repeat a desired part [A-B REPEAT]
• To quit A-B repeat playback
Press STOP. The unit stops playback and quits the A-
B repeat mode.
1
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
PLAY MODE DISPLAY RETURN
SHIFT
B.SEA
RCH
B.SKIP
4
CANCEL
PLAY
3
TIME CHOICE
F.SEARC
H
PAUS
E
8
ENTER
MENU
TITLE
UP
LEFT CURSOR RIGHT
DOWN
REMOTE CONTROL
2, 3
7
During playback
1
Press PLAY MODE - CANCEL.
The play mode menu appears on the TV screen.
2
Use CURSOR 2/3 to move to [A-B
REPEAT], then press ENTER at the beginning of the part you want to repeat (point A).
Make sure that REPEAT mode is off. If any one of the REPEAT modes is selected, you cannot move
to [A-B REPEAT].
3
Press ENTER at the end of the part you want to repeat (point B).
The unit locates “A” and starts repeat playback between “A” and “B.”
(for DVD VIDEO)
DVD CONTROL
REPEAT A-B REPEAT TIME SEARCH CHAP. SEARCH
(for Audio CD)
CD CONTROL
REPEAT A-B REPEAT TIME SEARCH
A 0:00:16 B 0:01:16 A 0: 00:16 B 0: 01:31
• During playback, pressing ENTER when is pointed at [A-
B REPEAT] quits the A-B repeat mode and continues playback.
• You can also quit the A-B repeat mode by pressing
4 or
¢.
NOTES
• To turn off the play mode menu
Press PLAY MODE - CANCEL.
• If appears when pressing ENTER in step 2 during DVD playback
You cannot repeat the selected portion because of the disc contents.
• The A-B REPEAT function cannot be used during program playback.
Point A Point B Point A Point B
(for Video CD)
VCD CONTROL
REPEAT A-B REPEAT TIME SEARCH PBC CALL
A 0: 00:16 B 0: 01:31
Point A Point B
29
EN20-34.XV-521BK[1U] 29 00.6.9, 3:30 PM
XV-521BK [1U] EN
LVT0435-011A
Selecting a scene angle of
DVD VIDEO
You can enjoy a variety of scene angles if the DVD
VIDEO disc contains “multi-angle” parts, where multiple cameras were used to shoot the same scene from different angles.
At the beginning of “multi-angle” parts, screen.
appears on the TV
To select a scene angle from the normal screen [ANGLE]
2
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
PLAY MODE DISPLAY RETURN
SHIFT
B.SEA
RCH
B.SKIP
4
PAUS
E
8
CANCEL
PLAY
3
TIME CHOICE
F.SEARC
H
ENTER
MENU
TITLE
UP
LEFT CURSOR RIGHT
DOWN
REMOTE CONTROL
7
During DVD VIDEO playback
1
Press ANGLE - ZOOM.
The Angle selectin display appears on the TV screen.
1 / 3
1
2
Press ANGLE - ZOOM or CURSOR 2/3 to select the desired angle.
Each time you press
ANGLE or CURSOR 2/3, the angle changes.
Example:
1 / 3
2 / 3
3 / 3
NOTES
• The Angle selection display will automatically disappear if you do not change the angle for 10 seconds.
• To turn off the Angle selection display manually, press
ENTER.
• When appears on the TV screen
The current scene is not recorded from multiple angles.
Advanced operations
To select a scene angle from the angle list display [ANGLE]
3
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
PLAY MODE DISPLAY RETURN
SHIFT
CANCEL
B.SEA
RCH
B.SKIP
4
PLAY
3
TIME CHOICE
F.SEARC
H
PAUS
E
8
ENTER
MENU
TITLE
LEFT
UP
CURSOR RIGHT
DOWN
REMOTE CONTROL
1
2
7
During DVD VIDEO playback
1
Press and hold ANGLE - ZOOM for more than
1 second.
Up to nine camera angles recorded on a disc appear on the
TV screen.
The selected camera angle
2
Use CURSOR 5/∞/2/3 to select the desired angle.
3
Press ENTER.
7
The selected angle appears on the TV screen.
NOTES
• When appears on the TV screen in step 1:
The current scene is not recorded from multiple angles.
• During the operation above, audio is muted.
30
EN20-34.XV-521BK[1U] 30 00.6.9, 3:30 PM
XV-521BK [1U] EN
LVT0435-011A
Advanced operations
Changing the language and sound
For DVD VIDEO discs, you can select the subtitle language, as well as the audio language/sound included on a disc.
For Video CD discs, you can select the audio channel(s).
To select the subtitle language [SUBTITLE]
7
During DVD VIDEO playback
1, 2
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
SHIFT
PLAY MODE DISPLAY RETURN
CANCEL TIME CHOICE
B.SEA
RCH
B.SKIP
4
PLAY
3
F.SEARC
H
F.SKIP
¢
8
E
ENTER
MENU
TITLE
LEFT
UP
CURSOR RIGHT
DOWN 3
REMOTE CONTROL
1
Press SUBTITLE.
The Subtitle selection display appears on the
TV screen.
ON 1 / 3 ENGLISH
2
To turn the subtitle on and off, press
SUBTITLE.
3
To select the desired subtitle language, press
CURSOR 2/3.
Example:
Each time you press
CURSOR 2/3, the subtitle language changes.
1/3 ENGLISH
2/3 FRENCH
3/3 SPANISH
31
–/3 (off)
NOTES
• For DVD VIDEO, the selected language may be abbreviated on the TV screen. See “Appendix A: Table of languages and their abbreviations” at the end of this manual.
• The Subtitle selection display will automatically disappear if you do not change the subtitle for 10 seconds.
• To turn off the Subtitle selection display manually, press
ENTER.
• When appears on the TV screen:
You cannot select the subtitle.
To change the audio language or sound
[AUDIO]
By AUDIO selection, you can choose the audio language of movies or choose to enjoy karaoke with or without the vocal.
1, 2
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
SHIFT
PLAY MODE DISPLAY RETURN
CANCEL TIME CHOICE
B.SEA
RCH
B.SKIP
4
PLAY
3
8
ENTER
MENU
TITLE
LEFT
UP
CURSOR RIGHT
DOWN 2
REMOTE CONTROL
7
During playback
1
Press AUDIO - STROBE.
The Audio selection display appears on the TV screen.
(DVD VIDEO) (Video CD)
STEREO 1 / 3 ENGLISH
2
Press AUDIO - STROBE or CURSOR 2/3 to select the desired audio.
• For DVD VIDEO
Each time you press AUDIO
- STROBE or CURSOR 2/3, the audio language or sound changes.
Example:
1/3 ENGLISH
2/3 FRENCH
3/3 SPANISH
• For Video CD
Each time you press AUDIO
- STROBE or CURSOR
2/3, the playback audio changes as follows.
STEREO
L
R
NOTES
• For DVD VIDEO, the selected language may be abbreviated on the TV screen. See “Appendix A: Table of languages and their abbreviations” at the end of this manual.
• The Audio selection display will automatically disappear if you do not change the audio for 10 seconds.
• To turn off the Audio selection display manually, press
ENTER.
• When appears on the TV screen (for a DVD VIDEO disc):
You cannot select the audio.
EN20-34.XV-521BK[1U] 31 00.6.9, 3:30 PM
XV-521BK [1U] EN
LVT0435-011A
Selecting the picture character
You can select the quality of the image from among four options (OFF, 1, 2 and 3) according to the type of programming, picture tone or personal preferences.
To select the picture character [THEATER
POSITION]
1
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
SHIFT
PLAY MODE DISPLAY RETURN
CANCEL TIME CHOICE
B.SEA
RCH
B.SKIP
4
PLAY
3
ENTER
8
MENU
TITLE
LEFT
UP
CURSOR RIGHT
DOWN
REMOTE CONTROL
7
During playback
1
Press THEATER POSITION to select the desired picture character.
Each time you press the button, the picture character changes as follows:
THEATER 1
Advanced operations
Enjoying virtual surround sound
Using the 3D Phonic function, you can get a simulated surround effect from your stereo system.
To simulate surround sound [3D PHONIC]
1, 2
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
PLAY MODE DISPLAY RETURN
SHIFT CANCEL
B.SEA
RCH
TIME CHOICE
F.SEARC
F.SKIP
H
¢
8
E
ENTER
TITLE
MENU
LEFT
UP
CURSOR
RIGHT
DOWN
REMOTE CONTROL
7
During playback
1
Press 3D PHONIC.
2
Select the desired effect mode by pressing 3D
PHONIC.
Each time you press 3D PHONIC, the effect mode changes as follows:
3D PHONIC DRAMA
EN20-34.XV-521BK[1U]
Selected picture character
THEATER 1
THEATER 2
THEATER 3
THEATER OFF
“THEATER OFF” is the normal position.
Selecting a higher number tones down the picture character.
32
Selected effect mode
3D PHONIC ACTION*
3D PHONIC DRAMA
3D PHONIC THEATER
3D PHONIC OFF
• ACTION:
Suitable for action movies and sports programs in which sounds dynamically move.
• DRAMA:
Natural and warm sound. You can enjoy movies in a relaxed mood.
• THEATER:
You can enjoy sound effects like in a major theater in
Hollywood.
32
00.6.9, 3:31 PM
XV-521BK [1U] EN
LVT0435-011A
Advanced operations
* When you play a DVD VIDEO disc recorded in Dolby
Digital which contains more than 2 channels, ACTION does not appear.
NOTES
• With a Video CD disc, if the AUDIO setting is set to L or
R, you cannot activate the 3D Phonic function (i.e. the
3D Phonic mode is fixed to OFF).
Conversely, when the 3D Phonic function is active, changing the AUDIO setting to L or R from STEREO cancels the 3D Phonic function.
• The 3D phonic function works correctly when playing back discs recorded in the Dolby Surround or Dolby
Digital 5.1-CH format.
It also works when playing back discs other than those above, but does not provide the correct effect.
• The 3D Phonic function does not affect the DTS or Dolby
Digital bitstream signal from the DIGITAL OUT jack.
• The sound effect will not be set or operate, even if 3D
PHONIC is pressed, for the sound of DVD VIDEO discs recorded in Linear PCM.
• When you set the 3D PHONIC function to on, the DOWN
MIX and COMPRESSION settings in the AUDIO page of the preference display are disabled.
Checking the status
You can check the disc/time information, as well as the
DVD functions, of the disc.
To check the disc/time information
2
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO
ANGLE
TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
PLAY MODE DISPLAY RETURN
SHIFT CANCEL
B.SEA
RCH
TIME CHOICE
F.SEARC
F.SKIP
H
¢
8 ENTER
MENU
TITLE
LEFT
UP
CURSOR
RIGHT
DOWN
REMOTE CONTROL
1
7
During playback
1
Press DISPLAY - TIME once for a Audio CD or
Video CD disc, or twice for a DVD VIDEO disc.
The disc/time display appears on the TV screen.
33
EN20-34.XV-521BK[1U] 33
During playback of a DVD VIDEO disc, pressing DISPLAY - TIME while holding down SHIFT directly turns on the disc/time display.
(for DVD VIDEO)
TITLE
1
CHAP.
25
TIME
2:25:25
BITRATE
3.3
Mbps
Transmission rate
Time
Current chapter number
Current title number
(for Audio CD or Video CD playing without PBC)
TRACK
1
TIME
00:08
EACH
Time mode
Time
Current track number
(for Video CD playing with PBC)
TRACK
1
TIME
25:25 PBC
PBC on status
Time
Current track number
00.6.9, 3:31 PM
XV-521BK [1U] EN
LVT0435-011A
2
To change the time display mode (only for
Audio CD or Video CD without PBC), press
DISPLAY - TIME while holding down SHIFT.
The time display mode cycles as below.
(for Audio CD)
EACH
(current track elapsed time)
EACH REMAIN
(current track remaining time)
TOTAL
(disc elapsed time)
TOTAL REMAIN
(disc remaining time)
(for Video CD without PBC)
EACH
(current track elapsed time)
EACH REMAIN
(current track remaining time)
The selected time information is displayed on the
TV screen, as well as in the front panel display window.
7
While stopped
You can check the total disc time and current (selected) track time of an Audio CD/Video CD only from the front panel display window.
1
Press DISPLAY - TIME while holding down
SHIFT.
When EACH and REMAIN are indicated, the current (selected) track time appears. When only
REMAIN is indicated, the total disc time appears.
To check the DVD function status
7
During DVD VIDEO playback
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
PLAY MODE DISPLAY RETURN
SHIFT CANCEL
B.SEA
RCH
TIME CHOICE
F.SEARC
F.SKIP
H
¢
8
E
ENTER
TITLE
MENU
UP
LEFT
CURSOR
DOWN
RIGHT
REMOTE CONTROL
Advanced operations
1
1
Press DISPLAY – TIME.
The DVD function status display appears on the
TV screen.
1 / 2 1 / 2
ENGLISH
1 / 2
ENGLISH
The current selections of the camera angle, audio language and subtitle language are displayed.
• To turn off the DVD function status display
Press DISPLAY-TIME twice.
You can change the current (selected) track by pressing
4 or
¢.
• To turn off the disc/time display
Press DISPLAY-TIME.
34
EN20-34.XV-521BK[1U] 34 00.6.9, 3:31 PM
XV-521BK [1U] EN
LVT0435-011A
Initial settings
Initial settings
Selecting preferences
You can set various preferences for playback via four dedicated displays.
How to set preferences
2
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
PLAY MODE DISPLAY RETURN
SHIFT
8
E
CANCEL
STOP
7
TIME CHOICE
F.SEARC
F.SKIP
H
¢
ENTER
MENU
TITLE
LEFT
UP
CURSOR
RIGHT
DOWN
REMOTE CONTROL
1
3
1
When a DVD or Video CD disc is stopped or no disc is inserted, press RETURN-CHOICE while holding down SHIFT.
One of the preference pages appears on the TV screen.
There are four preference pages: LANGUAGE,
AUDIO, DISPLAY and SYSTEM. To turn the page, move to the desired tab using CURSOR 2/3.
LANGUAGE
LANGUAGE AUDIO
MENU LANGUAGE
AUDIO LANGUAGE
SUBTITLE
ON SCREEN LANGUAGE
DISPLAY SYSTEM
ENGLISH
ENGLISH
ENGLISH
ENGLISH
EXIT
PRESS KEY
AUDIO
LANGUAGE AUDIO
DIGITAL AUDIO OUTPUT
DOWN MIX
COMPRESSION
DISPLAY SYSTEM
/PCM
Lo / Ro
ON
EXIT
PRESS KEY
DISPLAY
LANGUAGE AUDIO
MONITOR TYPE
SCREEN SAVER
ON SCREEN GUIDE
DISPLAY
4:3 LB
OFF
ON
SYSTEM
EXIT
PRESS KEY
SYSTEM
LANGUAGE AUDIO
AUTO STANDBY
RESUME
AV COMPULINK MODE
DISPLAY SYSTEM
OFF
OFF
DVD 1
EXIT
PRESS KEY
2
Move to select the item you want to set by using CURSOR 5/∞.
LANGUAGE AUDIO
MENU LANGUAGE
AUDIO LANGUAGE
SUBTITLE
ON SCREEN LANGUAGE
DISPLAY SYSTEM
ENGLISH
ENGLISH
ENGLISH
ENGLISH
EXIT
PRESS KEY
3
Press CURSOR 2/3 to select the setting you want.
• To turn off the preference display, press RETURN-CHOICE while holding down SHIFT, or move to [EXIT] and press ENTER.
• For details about each setting, see the following paragraphs:
LANGUAGE page
MENU LANGUAGE
You can select the default “display” language to be displayed if it is contained on the disc.
Each time you press
CURSOR 3, the language setting changes in the following order:
LANGUAGE AUDIO
MENU LANGUAGE
AUDIO LANGUAGE
SUBTITLE
ON SCREEN LANGUAGE
DISPLAY SYSTEM
ENGLISH
ENGLISH
ENGLISH
ENGLISH
EXIT
PRESS KEY
ENGLISH = SPANISH = FRENCH = CHINESE =
GERMAN = ITALIAN = JAPANESE = language code from AA to ZU
(See “Table of languages and their abbreviations” at the end of this manual.)
Pressing CURSOR 2 changes the language setting in the reverse order of the above.
* If the selected language is not recorded, the disc’s default display language will be displayed.
AUDIO LANGUAGE
You can select the default audio language to be played if it is contained on the disc.
Each time you press
CURSOR 3, the language setting changes in the following order:
LANGUAGE AUDIO DISPLAY
MENU LANGUAGE
AUDIO LANGUAGE
SUBTITLE
ON SCREEN LANGUAGE
SYSTEM
ENGLISH
ENGLISH
ENGLISH
ENGLISH
EXIT
PRESS KEY
ENGLISH = SPANISH = FRENCH = CHINESE =
GERMAN
= ITALIAN = JAPANESE = language code from AA to ZU
(See “Table of languages and their abbreviations” at the end of this manual.)
Pressing CURSOR 2 changes the language setting in the reverse order of the above.
* If the selected language is not recorded, the disc’s default audio language will be played.
35
EN35-40.XV-521BK[1U] 35 00.6.9, 3:31 PM
XV-521BK [1U] EN
LVT0435-011A
SUBTITLE
You can select the default subtitle language to be displayed if it is contained on the disc.
Each time you press
CURSOR
3, the language setting changes in the following order:
LANGUAGE AUDIO
MENU LANGUAGE
AUDIO LANGUAGE
SUBTITLE
ON SCREEN LANGUAGE
DISPLAY SYSTEM
ENGLISH
ENGLISH
ENGLISH
ENGLISH
EXIT
PRESS KEY
ENGLISH = SPANISH = FRENCH = CHINESE =
GERMAN = ITALIAN = JAPANESE = language code from AA to ZU
(See “Table of languages and their abbreviations” at the end of this manual.)
Pressing CURSOR
2 changes the language setting in the reverse order of the above.
* If the selected language is not recorded, the disc’s default subtitle language will be displayed.
ON SCREEN LANGUAGE
You can select the on-screen display language to be displayed.
Each time you press
CURSOR 3, the language setting changes as follows:
LANGUAGE AUDIO
MENU LANGUAGE
AUDIO LANGUAGE
SUBTITLE
ON SCREEN LANGUAGE
DISPLAY SYSTEM
ENGLISH
ENGLISH
ENGLISH
ENGLISH
EXIT
PRESS KEY
ENGLISH
ESPAÑOL (Spanish)
FRANCAIS (French)
English ON SCREEN LANGUAGE
Spanish
IDIOMA EN PANTALLA
French LANGUE D’ECRAN
ENGLISH
ESPAÑOL
FRANCAIS
Pressing CURSOR 2 changes the language setting in the reverse order of the above.
EN35-40.XV-521BK[1U] 36
Initial settings
AUDIO page
DIGITAL AUDIO OUTPUT
To connect the unit‘s digital output to an external device equipped with a digital input, this item must be set correctly.
LANGUAGE AUDIO
DIGITAL AUDIO OUTPUT
DOWN MIX
COMPRESSION
DISPLAY SYSTEM
DOLBY
DIGITAL
/PCM
Lo / Ro
ON
PRESS KEY
EXIT
• PCM ONLY:
When you connect the DIGITAL OUT jack of the unit to the linear PCM digital input of other audio equipment.
• STREAM/PCM:
When you connect to the digital input of an amplifier to a built-in DTS, Dolby Digital, or MPEG multichannel decoder.
• DOLBY DIGITAL/PCM:
When you connect to the digital input of a Dolby
Digital decoder, or an amplifier with a built-in Dolby
Digital decoder.
The following chart shows the relationship between types of playback discs and output signals.
Playback discs
DVD with 48-kHz,
16-bit linear PCM
DVD with 48-kHz,
20/24-bit linear
PCM
DVD with 96-kHz, linear PCM
DVD with DTS
STREAM/PCM
48-kHz,
16-bit linear
PCM
Output
DOLBY DIGITAL/PCM
←
←
48-kHz,
20-bit linear
PCM
No output
←
PCM ONLY
←
←
←
←
DVD with Dolby
Digital
DVD with MPEG multichannel
Video CD
Audio CD
Audio CD with
DTS
DTS bitstream
Dolby Digital bitstream
MPEG bitstream
44.1-kHz,
16-bit linear
PCM
44.1-kHz,
16-bit linear
PCM
DTS bitstream
No output
←
48-kHz, 16-bit linear PCM
←
←
←
48-kHz, 16-bit linear PCM
←
←
←
←
NOTES
• The unit does not provide the DTS decoding function.
• When playing a DVD VIDEO or Audio CD disc with DTS, use a DTS decoder to get correct signals from your speakers. Never use the unit's analog output jacks, which output incorrect signals that may damage your speakers.
If you connect the analog outputs and digital outputs simultaneously, be sure to select the source of the amplifier correctly, or set the level control of the amplifier connected to the analog outputs to minimum.
36
00.6.9, 3:31 PM
XV-521BK [1U] EN
LVT0435-011A
37
Initial settings
DOWN MIX
To playback a DVD VIDEO disc recorded with surround multichannel audio correctly, the DOWN
MIX setting must be properly made according to your audio system.
LANGUAGE
DIGITAL AUDIO OUTPUT
DOWN MIX
COMPRESSION
PRESS
AUDIO
KEY
DISPLAY SYSTEM
/PCM
Lo / Ro
ON
EXIT
Note that this setting affects the output signal from the
AUDIO (both DIGITAL and ANALOG) output jacks when playing back a DVD VIDEO disc recorded with surround multichannel audio.
• Lt/Rt
When you enjoy multichannel surround audio by connecting the unit’s AUDIO output (normally, the
DIGITAL output) to a surround decoder.
• Lo/Ro
When you enjoy conventional 2-channel stereo audio by connecting the unit’s AUDIO output(s) to a stereo amplifier/receiver or television set, or when you duplicate audio of a DVD VIDEO disc recorded with surround audio to your MD,cassette, etc.
NOTE
The Down mix function does not work when the 3D PHONIC function is activated.
COMPRESSION
You can compress the dynamic range of the sound if needed. Using this function, you can listen to sound at low volumes easily.
LANGUAGE AUDIO
DIGITAL AUDIO OUTPUT
DOWN MIX
COMPRESSION
DISPLAY SYSTEM
DOLBY
DIGITAL
/PCM
Lo / Ro
ON
EXIT
PRESS KEY
• ON
Audio is played back with the dynamic range compressed.
• OFF
Audio is played back as it was recorded.
NOTES
• The Compression function works only when playing back a disc recorded with DOLBY DIGITAL 1CH or 2CH. The setting is not effective for other discs.
• The Compression function does not work when the 3D
PHONIC function is activated.
DISPLAY page
MONITOR TYPE
You can select the monitor type to match your TV when you playback DVD
VIDEO discs recorded for wide screen televisions.
LANGUAGE AUDIO
MONITOR TYPE
SCREEN SAVER
ON SCREEN GUIDE
DISPLAY
4:3 LB
OFF
ON
SYSTEM
EXIT
PRESS KEY
• 4:3 LB (Letter Box Conversion)
When you connect a normal TV to the unit.
When you play a wide picture recorded on a DVD VIDEO disc, the picture is displayed with bands across the upper and lower portions of the screen.
• 4:3 PS (Pan Scan Conversion)
When you connect a normal TV to the unit.
When you play a wide picture recorded on a DVD
VIDEO disc, a portion of the picture is automatically cut off from the left and right sides of the image.
Depending on the disc, it may not be possible to playback in this mode. In that case, the picture is played back as in 4:3
LB mode.
• 16:9 WIDE (Wide Television screen)
When you connect a wide-screen TV to the unit.
SCREEN SAVER
A television monitor screen may be burned out if a static picture is displayed for a long time. To prevent this, the unit automatically activates the screen saver function if a static picture, such as an on-screen display or menu, is displayed for over 5 minutes.
• MODE 1
The current picture gets dark.
• MODE 2
The “screen saver” picture appears and its brightness changes.
• OFF
The screen saver function is off.
LANGUAGE AUDIO
MONITOR TYPE
SCREEN SAVER
ON SCREEN GUIDE
DISPLAY
4:3 LB
OFF
ON
SYSTEM
EXIT
PRESS KEY
NOTES
• The monitor screen of a projector or projection TV is easily burned out if the screen saver mode is set to OFF and a static picture is displayed for a long time.
• The screen saver function is not activated when the selected disc is an Audio CD.
EN35-40.XV-521BK[1U] 37 00.6.9, 3:31 PM
XV-521BK [1U] EN
LVT0435-011A
ON SCREEN GUIDE
The unit can display “onscreen guide” icons or characters on the picture, which show what is happening to the disc or the unit.
LANGUAGE AUDIO
MONITOR TYPE
SCREEN SAVER
ON SCREEN GUIDE
DISPLAY
4:3 LB
OFF
ON
SYSTEM
EXIT
PRESS KEY
• ON
The on-screen guide will be displayed.
• OFF
The on-screen guide will not be displayed.
Examples of “on-screen guide” icons or characters:
, ,
Initial settings
SYSTEM page
AUTO STANDBY
When the unit is stopped for more than 30 minutes or 60 minutes, the unit enters standby mode automatically.
• 60
Time is set to 60 minutes.
• 30
Time is set to 30 minutes.
• OFF
The auto standby function is off.
LANGUAGE AUDIO
AUTO STANDBY
RESUME
AV COMPULINK MODE
DISPLAY SYSTEM
OFF
OFF
DVD 1
EXIT
PRESS KEY
RESUME
You can select the resume function to be on or off.
See page 19.
• ON
Pressing PLAY while stopped or on standby starts playback from the resume point if it is memorized.
• OFF
Pressing PLAY while stopped or on standby starts playback from the beginning of the disc.
LANGUAGE AUDIO
AUTO STANDBY
RESUME
AV COMPULINK MODE
DISPLAY SYSTEM
OFF
OFF
DVD 1
EXIT
PRESS KEY
AV COMPULINK MODE
If you use the AV
Compulink system, you must set this item correctly.
Select from the three options: “DVD1,” “DVD2” and “DVD3” according to the equipment to be connected.
See page 41.
LANGUAGE AUDIO
AUTO STANDBY
RESUME
AV COMPULINK MODE
DISPLAY SYSTEM
OFF
OFF
DVD 1
EXIT
PRESS KEY
38
EN35-40.XV-521BK[1U] 38 00.6.9, 3:31 PM
XV-521BK [1U] EN
LVT0435-011A
Initial settings
Limiting playback by children
This function restricts playback of DVD VIDEO discs which contain violent (and other) scenes according to the level set by the user. For example, if a movie which includes violent scenes supports the parental lock feature, such scenes which you do not want to let children view can be cut or replaced with other scenes.
To set Parental Lock for the first time
[PARENTAL LOCK]
1
2, 4
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
SHIFT
PLAY MODE DISPLAY RETURN
CANCEL TIME CHOICE
B.SEA
RCH
B.SKIP
4
PLAY
3
F.SEARC
H
F.SKIP
¢
8
E
ENTER
MENU
TITLE
LEFT
UP
CURSOR RIGHT
DOWN
REMOTE CONTROL
6
1, 3, 5, 7
7
While a DVD VIDEO disc is stopped or no disc is inserted
1
Press ENTER while holding down SHIFT.
The Parental Lock on-screen display appears on the TV screen.
points [Country Code].
2
While points [Country Code], use
CURSOR 2/3 to select “US” for country code.
Country Coce
Set Level
PASS WORD
PARENTAL LOCK
US
—
- - - -
EXIT
PRESS KEY ENTER
3
Press ENTER.
moves to [Set Level].
4
While points [Set Level], use CURSOR
2/3 to select the parental lock level.
Country Code
Set Level
PASS WORD
PARENTAL LOCK
US
1
- - - -
EXIT
PRESS KEY ENTER
Each time you press CURSOR 2/3, the parental level changes as follows:
1
.
.
.
8
–
“1” is the strictest level. “–” means no restriction.
Discs rated higher than the selected level are restricted.
5
Press ENTER.
moves to [PASSWORD].
6
Enter your 4-digit password using the numeric buttons (0 to 9).
Country Code
Set Level
PASS WORD
PARENTAL LOCK
US
1
- - - -
EXIT
NEW PASSWORD? ··· PRESS 0~9 KEY.
7
Press ENTER.
The parental level and password are set.
moves to [EXIT].
Pressing ENTER again returns to the opening display.
If you enter an undesired password in step 6 above, reenter the password before pressing ENTER.
39
EN35-40.XV-521BK[1U] 39 00.6.9, 3:31 PM
XV-521BK [1U] EN
LVT0435-011A
To change the settings [PARENTAL LOCK]
1
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
PLAY MODE DISPLAY RETURN
SHIFT
CANCEL
B.SEA
RCH
B.SKIP
4
PLAY
3
TIME CHOICE
F.SEARC
H
PAUS
E
8
ENTER
MENU
TITLE
LEFT
UP
CURSOR RIGHT
DOWN
2, 5
3, 4
REMOTE CONTROL
1, 2, 3,
4, 5
You can change the Parental lock settings later.
7
While a DVD VIDEO disc is stopped or no disc is inserted
1
Press ENTER while holding down SHIFT.
The Parental Lock on-screen display appears on the TV screen.
Country Code
Set Level
PASS WORD
PARENTAL LOCK
US
1
- - - -
EXIT
points
[PASSWORD].
CURRENT PASSWORD? ··· PRESS 0~9 KEY
2
Enter your current 4-digit password using the numeric buttons (0 to 9) and press ENTER.
moves to [Country Code] if you enter the correct password.
If you enter the wrong password, “WRONG!
RETRY……” appears on the TV screen, and you cannot go to next step.
3
To change the country code, use CURSOR 2/
3 to select the desired country code and press ENTER.
moves to [Set Level].
When you change the country code, you must select the parental level.
4
To change the set level, use CURSOR 2/3 to select the desired level while points [Set
Level], and then press ENTER.
moves to [PASSWORD].
5
Enter the password using the numeric buttons (0 to 9) and press ENTER.
moves to [EXIT].
The password entered in the above step becomes the new password. If you do not change the password, enter the same password as in the step
2.
Initial settings
Even if you want to change only the country code and/or parental level, do not forget to enter the password after changing the country code and/or parental level. Otherwise, the new country code and/or parental level will not become effective.
Pressing ENTER again returns to the opening display.
NOTES
• When you enter the wrong password more than 3 times in step 2 above, moves to [EXIT] automatically and
CURSOR
5/∞ does not work.
• If you forget your password in step 2
Enter “8888.”
To temporarily release the Parental lock
[PARENTAL LOCK]
OPEN
/CLOSE 3D-PHONIC
THEATER
POSITION
TV POWER
DVD POWER
SUBTITLE AUDIO ANGLE TV/VIDEO
DIGEST
1
TV 1
4
TV 4
7
TV 7
10
TV RETURN
STROBE
2
TV 2
ZOOM
5
TV 5
8
TV 8
0
TV 0
3
TV 3
6
TV 6
9
TV 9
+10
TV 100+
SLOW
AMP
VOL
TV
VOL
TV ch
PLAY MODE DISPLAY RETURN
SHIFT
B.SEA
RCH
CANCEL
PLAY
3
TIME CHOICE
F.SEARC
F.SKIP
H
¢
8
E
ENTER
MENU
TITLE
UP
LEFT
CURSOR
DOWN
RIGHT
2
1
REMOTE CONTROL
When you set the parental level strictly, some discs may not be played back at all. When you insert such a disc and try to play it, the following Parental Lock onscreen display appears on the TV screen, asking you whether you want the parental lock to be temporarily released or not.
1
Use the CURSOR 5/∞ to move to [YES], then press ENTER.
moves to the
PASSWORD field.
When selecting
[NO], press OPEN/
CLOSE to remove the disc.
PARENTAL LOCK
This DISC can’t play now!
Temporary
YES
Level Change ?
NO
PASSWORD – – – –
PRESS ENTER EXECUTE
2
Enter your 4-digit password using the numeric buttons (0 to 9).
If you enter the wrong password, “WRONG!
RETRY…” appears on the TV screen, and you cannot go to next step.
The Parental lock is released, and the unit starts playback.
NOTE
When you enter the wrong password more than 3 times in step 2 above, moves to [NO] automatically and
CURSOR 5/∞ do not work.
40
EN35-40.XV-521BK[1U] 40 00.6.9, 3:31 PM
XV-521BK [1U] EN
LVT0435-011A
Additional information
Additional information
AV COMPU LINK remote control system
When you buy a separate TV, VCR, DVD player, receiver, or other component and connect them to each other, you have to operate each component individually. JVC’s
AV COMPU LINK remote control system meets the demands of a system made up of single components and has the ease of operation of a single unit.
Connection and setup
Using the AV COMPU LINK cable, connect the AV COMPU LINK terminals of each component to one another.
To AV COMPU LINK (II or EX)
TV
DVD player
• If you connect a DVD player to a television via AV COMPU LINK, set the DVD player’s AV COMPU LINK setting as follows.
• When connecting to VIDEO-1 input terminal of the television: DVD2
• When connecting to VIDEO-2 input terminal of the television: DVD3
To AV COMPU LINK (II or EX)
To AV COMPU LINK
TV
DVD player VCR (Video Cassette Recorder)
• If you connect a DVD player to a television and VCR via AV COMPU LINK, set the VCR’s Remote Control Code and
DVD player’s AV COMPU LINK setting as follows.
• When connecting to VIDEO-1 input terminal of the television:
DVD player’s AV COMPU LINK setting: DVD2
VCR’s Remote Control Code: B
• When connecting to VIDEO-2 input terminal of the television:
DVD player’s AV COMPU LINK setting: DVD3
VCR’s Remote Control Code: A
To AV COMPU LINK (II or EX)
TV
Receiver DVD player
• If you connect a DVD player to a television and receiver via AV COMPU LINK, set the DVD player’s AV COMPU LINK setting to DVD1.
• The DVD player’s AV COMPU LINK setting is operated in the SYSTEM page of the preference display.
See page 38 for operation.
• For information on the connection between the TV and the Receiver, refer to the Receiver’s Instructions.
IMPORTANT!
If you connect the component video output to your TV:
• set the DVD player’s AV COMPULINK setting to DVD1.
• make the video/audio connection between the DVD player and your receiver using the supplied audio/video cable, and do not make the S-VIDEO connection.
41
EN41-44.XV-521BK[1U] 41 00.6.9, 3:31 PM
Additional information
Notes for connection
• If you connect a DVD player to a receiver via AV COMPU LINK in a system including a Dolby digital decoder, some functions may not be performed automatically.
• The AV COMPU LINK terminal on some televisions indicates “II.” Do not connect the terminal indicating “II” with the AV COMPU LINK terminal on a receiver. If connected, the system will not work correctly.
• Connect the AUDIO OUT jacks of the DVD player to the audio input jacks of a receiver that indicating “DVD.”
Otherwise, the system will not work correctly.
• There may be no description about connections to a DVD player in the instruction manual of a television or VCR.
However a television or VCR with AV COMPU LINK terminals indicating “II” or “EX” can be connected to a DVD player.
Operation
You can enjoy pictures and/or sound by just putting a source component (which plays back the pictures and/or sound such as a DVD player or VCR) into play mode. You do not have to operate the TV and receiver including not having to perform power switching.
1
Turn on the main power of the television.
2
Insert a disc into the source component.
3
Press PLAY of the source component.
The following actions are performed automatically:
• Turning on the power for the television.
• Setting the source of the television to the external input (VIDEO-1 or VIDEO-2).
• Turning on the power for the receiver.
• Setting the source of the receiver to the component which has started playback.
Care and handling of discs
How to handle discs
When handling a disc, do not touch the surface of the disc.
Since discs are made of plastic, they are easily damaged.
If a disc gets dirty, dusty, scratched or warped, the images and sound will not be picked up correctly, and such a disc may cause the player to malfunction.
Label side
Do not damage the label side, stick paper to or use any adhesive on its surface.
Storage
Make sure that discs are kept in their cases. If discs are piled on top of one another without their protective cases, they can be damaged. Do not put discs in a location where they may be exposed to direct sunlight, or in a place where the humidity or temperature is high. Avoid leaving discs in your car!
Maintenance of discs
If there are fingerprints or other dirt adhering to a disc, wipe with a soft dry cloth, moving from the center outwards.
If a disc is difficult to clean, wipe with a cloth moistened with water.
Never use record cleaners, petrol, alcohol or any anti-static agents.
CAUTION
Sometimes during play noise or images may be garbled. This is sometimes due to the disc. (It may not be up to industry standards.)
These symptoms are caused by the discs, not by the malfunction of the unit.
42
EN41-44.XV-521BK[1U] 42 00.6.9, 3:31 PM
XV-521BK [1U] EN
LVT0435-011A
Additional information
Troubleshooting
What appears to be a malfunction may not always be serious. Please go through the following list before requesting service.
Symptom
Power does not come on.
Remote control does not work.
Possible case
Power plug is not inserted securely.
Too far from the unit.
The tip of the remote unit is not pointed in the right direction.
Batteries are exhausted.
Battery polarity is incorrect.
Remedy
Plug in securely.
More closer to the unit.
Point the infrared light- emitting window toward the remote sensor on the front panel.
Replace the batteries with new ones.
Take out the batteries and insert them again in the correct direction.
Connect the cable correctly.
No picture is displayed on the monitor.
Picture is noisy.
Connection of video cable is incorrect.
Input selection of TV is incorrect.
Disc is not playable.
The unit is connected to a VCR directly and the copyguard function is activated.
No audio is reproduced.
Connection is incorrect.
Input selection of amplifier is incorrect.
No audio is reproduced when playing back a DVD disc recorded with 96-kHz, linear PCM audio.
The audio signal is derived from the unit's DIGITAL OUT.
Sound is distorted or noise is generated.
Disc is dirty.
Picture does not fit the television screen.
MONITOR TYPE is not correctly set.
Television is not correctly set.
Operation is not possible.
Microcomputer malfunction due to lightning or static electricity.
Moisture condensation caused by a sudden change of temperature or humidity.
Select correctly.
Use a playable disc. (See page 11.)
Connect the unit so that the picture signal flows directly to the TV.
Check the connections.
Select correctly.
Use the AUDIO OUT when playing back such discs.
Wipe the disc surface.
Select monitor type correctly. (See page 37.)
Set the television correctly.
Turn off the power and unplug the power cord, then connect the power cord again.
Turn off the power, then turn it on a few hours later.
43
EN41-44.XV-521BK[1U] 43 00.6.9, 3:31 PM
Specifications
General
Readable discs:
Video format:
Other
Power requirements:
Power consumption:
Mass:
Dimensions (W x H x D):
DVD VIDEO, Audio CD, Video CD
NTSC
AC 110 V - 240 V , 50 Hz/60 Hz
17 W (POWER ON), 3.4 W (STANDBY mode)
3.2 kg (7.1 lbs)
435 mm x 95 mm x 297 mm
(17-3/16 inch x 3-3/4 inch x 11-3/4 inch)
Video output
COMPONENT (pin jacks):
VIDEO OUT (pin jack):
S-VIDEO OUT (S jack):
Horizontal resolution:
Signal to noise ratio:
Audio output
ANALOG OUT (pin jack):
DIGITAL OUT: COAXIAL:
OPTICAL:
Audio characteristics
Frequency response:
Dynamic range:
Wow and flutter:
Total harmonic distortion:
Y Output: 1.0 Vp-p (75
Ω
)
P B /P R Output: 0.7 Vp-p (75
Ω
)
1.0 Vp-p (75
Ω
)
Y Output:
C Output:
1.0 Vp-p (75
Ω
)
286 mVp-p (75
Ω
)
500 Lines
65 dB
2.0 Vrms (10 k
Ω
)
0.5 Vp-p (75
Ω
termination)
– 21 to –15 dBm (Peak)
CD
DVD
DVD
(sampling frequency 44.1 kHz): 2 Hz to 20 kHz
(sampling frequency 48 kHz):
(sampling frequency 96 kHz):
2 Hz to 22 kHz
2 Hz to 44 kHz
16 bit: More than 98 dB
20 bit: More than 106 dB
24 bit: More than 106 dB
Unmeasurable (less than ± 0.002%)
Less than 0.002%
* Specifications and appearance subject to change without prior notice.
Additional information
EN41-44.XV-521BK[1U] 44 00.6.9, 3:31 PM
44
XV-521BK [1U] EN
LVT0435-011A
Additional information
Appendix A: Table of languages and their abbreviations
When you select the subtitle language or sound, the languages shown below are displayed as abbreviations. To select the desired language, select the abbreviation corresponding the language you want to.
Catalan
Corsican
Czech
Welsh
Danish
Bhutani
Greek
Esperanto
Estonian
Basque
Persian
Finnish
Fiji
Faroese
Frisian
Irish
Afar
Abkhazian
Afrikaans
Ameharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Byelorussian
Bulgarian
Bihari
Bislama
Bengali, Bangla
Tibetan
Breton
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
ET
EU
FA
FI
FJ
FO
FY
GA
CA
CO
CS
CY
DA
DZ
EL
EO
BA
BE
BG
BH
BI
BN
BO
BR
AR
AS
AY
AZ
AA
AB
AF
AM
GD
GL
GN
GU
HA
HI
HR
HU
HY
IA
IE
Inupiak
Indonesian
Icelandic
Hebrew
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Korean (KOR)
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laothian
Lithuanian
Latvian, Lettish
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Malay (MAY)
Maltese
Burmese
Nauru
Nepali
Dutch
Norwegian
Occitan
(Afan) Oromo
Oriya
Panjabi
Polish
Pashto, Pushto
Portuguese
Quechua
Rhaeto-Romance
MN
MO
MR
MS
MT
MY
NA
NE
LN
LO
LT
LV
MG
MI
MK
ML
KL
KM
KN
KO
KS
KU
KY
LA
IK
IN
IS
IW
JI
JW
KA
KK
NL
NO
OC
OM
OR
PA
PL
PS
PT
QU
RM
Siswati
Sesotho
Sundanese
Swedish
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
Turkish
Tsonga
Kirundi
Rumanian
Russian
Kinyarwanda
Sanskrit
Sindhi
Sangho
Serbo-Croatian
Singhalese
Slovak
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Wolof
Xhosa
Yoruba
Zulu
TN
TO
TR
TS
TH
TI
TK
TL
SS
ST
SU
SV
SW
TA
TE
TG
SI
SK
SL
SM
SN
SO
SQ
SR
RN
RO
RU
RW
SA
SD
SG
SH
TT
TW
UK
UR
UZ
VI
VO
WO
XH
YO
ZU
EN XV-521BK[1U]APPENDIX 45 00.6.9, 3:31 PM
Additional information
Appendix B: Country code list for parental lock
This list is used for the parental Lock operation. For details, see page 39.
CK
CL
CM
CN
CO
CR
CA
CC
CF
CG
CH
CI
BS
BT
BV
BW
BY
BZ
BI
BJ
BM
BN
BO
BR
DJ
DK
DM
DO
DZ
EC
EE
EG
EH
ER
CY
CZ
DE
CU
CV
CX
BB
BD
BE
BF
BG
BH
AS
AT
AU
AW
AZ
BA
AL
AM
AN
AO
AQ
AR
AD
AE
AF
AG
AI
Burundi
Benin
Bermuda
Brunei Darussalam
Bolivia
Brazil
Bahamas
Bhutan
Bouvet Island
Botswana
Belarus
Belize
Canada
Cocos (Keeling) Islands
Central African Republic
Congo
Switzerland
Côte d’Ivoire
Cook Islands
Chile
Cameroon
China
Colombia
Costa Rica
Andorra
United Arab Emirates
Afghanistan
Antigua and Barbuda
Anguilla
Albania
Armenia
Netherlands Antilles
Angola
Antarctica
Argentina
American Samoa
Austria
Australia
Aruba
Azerbaijan
Bosnia and Herzegovina
Barbados
Bangladesh
Belgium
Burkina Faso
Bulgaria
Bahrain
Cuba
Cape Verde
Christmas Island
Cyprus
Czech Republic
Germany
Djibouti
Denmark
Dominica
Dominican Republic
Algeria
Ecuador
Estonia
Egypt
Western Sahara
Eritrea
KE
KG
KH
KI
KM
KN
KP
IQ
IR
IS
IT
JM
JO
JP
ES
ET
FI
FJ
FK
FM
HN
HR
HT
HU
ID
IE
IL
IN
IO
GT
GU
GW
GY
HK
HM
KR
KW
KY
KZ
LA
GI
GL
GM
GN
GP
GQ
GR
GS
FO
FR
FX
GA
GB
GD
GE
GF
GH
PN
PR
PT
PW
PY
QA
RE
RO
RU
RW
NO
NP
NR
NU
NZ
OM
NC
NE
NF
NG
NI
NL
PA
PE
PF
PG
PH
PK
PL
PM
MV
MW
MX
MY
MZ
NA
MQ
MR
MS
MT
MU
LY
MA
MC
MD
MG
MH
ML
MM
MN
MO
MP
LK
LR
LS
LB
LC
LI
LT
LU
LV
Spain
Ethiopia
Finland
Fiji
Falkland Islands
(Malvinas)
Micronesia
(Federated States of)
Faroe Islands
France
France, Metropolitan
Gabon
United Kingdom
Grenada
Georgia
French Guiana
Ghana
Gibraltar
Greenland
Gambia
Guinea
Guadeloupe
Equatorial Guinea
Greece
South Georgia and the
South Sandwich Islands
Guatemala
Guam
Guinea-Bissau
Guyana
Hong Kong
Heard Island and
McDonald Islands
Honduras
Croatia
Haiti
Hungary
Indonesia
Ireland
Israel
India
British Indian Ocean
Territory
Iraq
Iran (Islamic Republic of)
Iceland
Italy
Jamaica
Jordan
Japan
Kenya
Kyrgyzstan
Cambodia
Kiribati
Comoros
Saint Kitts and Nevis
Korea, Democratic
People’s Republic of
Korea, Republic of
Kuwait
Cayman Islands
Kazakhstan
Lao People’s Democratic
Republic
Montserrat
Malta
Mauritius
Maldives
Malawi
Mexico
Malaysia
Mozambique
Namibia
New Caledonia
Niger
Norfolk Island
Nigeria
Nicaragua
Netherlands
Norway
Nepal
Nauru
Niue
New Zealand
Oman
Panama
Peru
French Polynesia
Papua New Guinea
Philippines
Pakistan
Poland
Saint Pierre and
Miquelon
Pitcairn
Puerto Rico
Portugal
Palau
Paraguay
Qatar
Réunion
Romania
Russian Federation
Rwanda
Lebanon
Saint Lucia
Liechtenstein
Sri Lanka
Liberia
Lesotho
Lithuania
Luxembourg
Latvia
Libyan Arab Jamahiriya
Morocco
Monaco
Moldova, Republic of
Madagascar
Marshall Islands
Mali
Myanmar
Mongolia
Macau
Northern Mariana
Islands
Martinique
Mauritania
TG
TH
TJ
TK
TM
TN
TO
TP
TR
TT
TV
TW
TZ
SN
SO
SR
ST
SJ
SK
SL
SM
SV
SY
SZ
TC
TD
TF
SE
SG
SH
SI
SA
SB
SC
SD
UA
UG
UM
US
UY
UZ
VA
VC
WS
YE
YT
YU
ZA
ZM
ZR
ZW
VE
VG
VI
VN
VU
WF
United States
Uruguay
Uzbekistan
Vatican City State
(Holy See)
Saint Vincent and the
Grenadines
Venezuela
Virgin Islands (British)
Virgin Islands (U.S.)
Vietnam
Vanuatu
Wallis and Futuna
Islands
Samoa
Yemen
Mayotte
Yugoslavia
South Africa
Zambia
Zaire
Zimbabwe
Saudi Arabia
Solomon Islands
Seychelles
Sudan
Sweden
Singapore
Saint Helena
Slovenia
Svalbard and Jan Mayen
Slovakia
Sierra Leone
San Marino
Senegal
Somalia
Suriname
Sao Tome and Principe
El Salvador
Syrian Arab Republic
Swaziland
Turks and Caicos Islands
Chad
French Southern
Territories
Togo
Thailand
Tajikistan
Tokelau
Turkmenistan
Tunisia
Tonga
East Timor
Turkey
Trinidad and Tobago
Tuvalu
Taiwan, Province of
China
Tanzania, United
Republic of
Ukraine
Uganda
United States Minor
Outlying Islands
EN XV-521BK[1U]APPENDIX 46 00.6.9, 3:31 PM
XV-521BK [1U] EN
LVT0435-011A
VICTOR COMPANY OF JAPAN, LIMITED
EN.
EN XV-521BK[1U]COVER 2 00.6.9, 3:29 PM
J
V
C
0700RIMUBNJSC
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project