ADLINK Technology PCIe-FIW Series User`s manual

GIE64+
4-CH PoE GigE Vision Interface Card
User’s Manual
Manual Rev.:
2.00
Revision Date:
Feb. 24, 2012
Part No:
50-11245-1000
Advance Technologies; Automate the World.
Revision History
ii
Revision
Release Date
2.00
Feb. 24, 2012
Description of Change(s)
Initial release
GIE64+
Preface
Copyright 2012 ADLINK Technology Inc.
This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form
without prior written permission of the manufacturer.
Disclaimer
The information in this document is subject to change without prior
notice in order to improve reliability, design, and function and does
not represent a commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or
inability to use the product or documentation, even if advised of
the possibility of such damages.
Environmental Responsibility
ADLINK is committed to fulfill its social responsibility to global
environmental preservation through compliance with the European Union's Restriction of Hazardous Substances (RoHS) directive and Waste Electrical and Electronic Equipment (WEEE)
directive. Environmental protection is a top priority for ADLINK.
We have enforced measures to ensure that our products, manufacturing processes, components, and raw materials have as little
impact on the environment as possible. When products are at their
end of life, our customers are encouraged to dispose of them in
accordance with the product disposal and/or recovery programs
prescribed by their nation or company.
Trademarks
Product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks
of their respective companies.
Preface
iii
Conventions
Take note of the following conventions used throughout this
manual to make sure that users perform certain tasks and
instructions properly.
Additional information, aids, and tips that help users perform
tasks.
NOTE:
CAUTION:
WARNING:
iv
Information to prevent minor physical injury, component damage, data loss, and/or program corruption when trying to complete a task.
Information to prevent serious physical injury, component
damage, data loss, and/or program corruption when trying to
complete a specific task.
Preface
GIE64+
Table of Contents
Revision History...................................................................... ii
Preface .................................................................................... iii
List of Figures ....................................................................... vii
List of Tables.......................................................................... ix
1 Introduction ........................................................................ 1
1.1
Overview.............................................................................. 1
1.2
Features............................................................................... 1
1.3
Applications ......................................................................... 2
1.4
1.5
Specifications....................................................................... 2
1.4.1
Power over Ethernet Port ........................................... 2
1.4.2
General Specifications................................................ 3
Unpacking Checklist ............................................................ 4
2 Getting Started ................................................................... 5
2.0.1
RJ-45 Ethernet Port.................................................... 6
2.0.2
Status LEDs................................................................ 7
2.0.3
Power Connector........................................................ 8
3 Hardware Installation ......................................................... 9
Important Safety Instructions .............................................. 11
Getting Service...................................................................... 13
Table of Contents
v
This page intentionally left blank.
vi
Table of Contents
GIE64+
List of Figures
Figure 2-1:
Figure 2-2:
Figure 2-3:
Figure 2-4:
Figure 2-5:
GIE64+ Schematic Diagram ............................................ 5
GIE64+ Board Layout ...................................................... 6
RJ-45 Ethernet Connector ............................................... 6
Status LEDs..................................................................... 7
Power Connector ............................................................. 8
List of Figures
vii
This page intentionally left blank.
viii
List of Figures
GIE64+
List of Tables
Table
Table
Table
Table
2-1:
2-2:
2-3:
2-4:
List of Tables
Board Layout Legend ...................................................... 6
RJ-45 Ethernet Port Connector Signals........................... 7
Status LED Legend ......................................................... 8
Power Connector Pin Assignments ................................. 8
ix
This page intentionally left blank.
x
List of Tables
GIE64+
1
Introduction
1.1 Overview
ADLINK's GIE64+ is a PCI Express® x4 lane, PoE (Power over
Ethernet) frame grabber with support for four independent Gigabit
Ethernet ports. Multiple Gigabit Ethernet Vision device connections are supported for standard Gigabit Ethernet Vision data
transfer rates of up to 1000 Mb/s.
The GIE64+ features not only PoE, combining power supply and
signal into a single cable, but also IEEE 1588 (precise time protocol), enabling synchronization with multi-camera acquisition.
The ADLINK GIE64+ also supports the Link aggregation control
protocol, offering inexpensive setup of a double-speed backbone
network for data transfers significantly exceeding those of a single
Gigabit Ethernet port or device.
1.2 Features
X
IEEE802.3af (48 V,15.4 W per channel) compliant, supporting classes 0,1,2,3,4
X
Powered Device (PD) auto-detection and classification
X
Support for four independent GbE ports
X
Support for Link aggregation
X
Support for jumbo frames (9.5 kBytes)
X
IEEE 1588 compliant, supporting multi-camera synchronization
X
Inrush current, current limit, and short-circuit protection
X
PCI Express x4 compliant
1.3 Applications
The GIE64+ is ideally suited to frame grab functions in a wide variety of applications, including:
X
Machine Vision Inspection systems
X
Scientific research instrumentation
X
Medical research instrumentation
Introduction
1
1.4 Specifications
1.4.1
Power over Ethernet Port
The GIE64+ Power over Ethernet specification supports
2
X
Four fully-integrated Gigabit Ethernet Media Access Control
(MAC) and physical layer (PHY) ports
X
Full controller compliance with IEEE 802.3.af standard for
maximum 15.4 watts, with power up to 48 V over existing
CAT-5 Ethernet infrastructure, with no modifications
required
X
Standard IEEE 802.3 Ethernet interface provided for
1000BASE-T, 100BASE-TX, and 10BASE-T applications
(802.3, 802.3u, and 802.3ab)
X
9 kB jumbo frame support
Introduction
GIE64+
1.4.2
General Specifications
Function
Description
Power Requirements
X
Input voltage: 12 VDC, (w/ PC system
power)
X
Input current: Max. 6 A @ 12 VDC
(supporting up to 4 ports at 15.4 W
per PoE port)
PCI Express
PCIe X4 ports
1 port PCIe X4, for GigE Vision
Differential Output Peak
+0.8 V to +1.2 V
to Peak Voltage
Differential Input Peak
to Peak Voltage
+0.175 V to +1.2 V
Input voltage for
PERST#, WAKE#, and
SMBus
-0.75 V to +4.05 V
Gigabit Ethernet
LAN chip
Intel® 82574L, PCIe v1.1 (2.5GT/s)
Gigabit Ethernet Ports
4
PoE Signal
Max Output Power
15.4 W per channel, IEEE 802.3af compliant
VPORT_POSx
44 to 55 V, PoE port positive voltage feed
Isolation +12V to +48V DC/DC Converter (Optional)
Output Current
Max 1.6 A (full load)
Power Supply
Max 75 W
Isolation Voltage
Min 2250 VDC (input to output)
Physical
Dimensions
168 W x 111.15 L mm (6.61 X 4.38 in.)
Operating Temperature
0° C to 55° C
Storage Temperature
-40° C to 85° C
Safety Compliance
CE/FCC Class A; RoHS
Introduction
3
X Always disconnect the power cord from the
chassis when working on the device, and do not
reconnect while the power switch is on, since
sudden power input can damage sensitive electronic components
X Only authorized and experienced electronics
personnel should open the chassis
X Always ground yourself to remove any static
electric charge before touching EOS, the device
is very sensitive to static electric charges; use a
grounding wrist strap at all times, and place all
electronic components on a static-dissipative
surface or in a static-shielded bag
1.5 Unpacking Checklist
Before unpacking, check the shipping carton for any damage. If
the shipping carton and/or contents are damaged, inform your
dealer immediately. Retain the shipping carton and packing
materials for inspection. Obtain authorization from your dealer
before returning any product to ADLINK. Ensure that the following items are included in the package.
X
GIE64+ unit
X
User’s manual
OEM versions with non-standard configuration, functionality, or
packaging may vary according to individual requirements.
NOTE:
4
Introduction
GIE64+
2
Getting Started
All dimensions shown are in mm
NOTE:
111.15
168
Figure 2-1: GIE64+ Schematic Diagram
Getting Started
5
D
C
B
A
Figure 2-2: GIE64+ Board Layout
A
PCIe lane
B
RJ-45 Ethernet Ports
C
Status LED
D
Power Connector
Table 2-1: Board Layout Legend
2.0.1
RJ-45 Ethernet Port
1
8
Figure 2-3: RJ-45 Ethernet Connector
6
Getting Started
GIE64+
Pin
Signal
1
MDI0+ (PoE_DC48V)
2
MDI0- (PoE_DC48V)
3
MDI1+ (PoE_DC0V)
4
MDI2+ (PoE_DC48V)
5
MDI2- (PoE_DC48V)
6
MDI1- (PoE_DC0V)
7
MDI3+ (PoE_DC0V)
8
MDI3- (PoE_DC0V)
Table 2-2: RJ-45 Ethernet Port Connector Signals
2.0.2
Status LEDs
Figure 2-4: Status LEDs
Getting Started
7
The GIE64+ provides four yellow LEDs to indicate operating conditions of the four PoE ports, as shown, with corresponding status
as follows.
LED
Status
1
ON: Port 1 PoE On
OFF: Port 1 PoE Off
2
ON: Port 2 PoE On
OFF: Port 2 PoE Off
3
ON: Port 3 PoE On
OFF: Port 3 PoE Off
4
ON: Port 4 PoE On
OFF: Port 4 PoE Off
Table 2-3: Status LED Legend
2.0.3
Power Connector
4
3
2
1
Figure 2-5: Power Connector
Pin
Signal
1
+12V
2
GND
3
GND
4
NC
Table 2-4: Power Connector Pin Assignments
8
Getting Started
GIE64+
3
Hardware Installation
The following describes installation of the GIE64+ module on the
PCI express bus.
1. Remove the computer cover according to the computer
manual..
NOTE:
A vacant PCI express slot is required for installation of the
GIE64+ module; if none is available, remove a PCI express
board and note the slot number.
2. Remove the slot cover (if any), retaining the fixing screw.
3. Carefully position the GIE64+ in the selected PCI
express slot. If installing in a tower computer, align the
board with the board slots.
4. Press the board firmly but carefully into the connector.
5. Anchor the board with the screw.
6. Plug the cable into the PoE power connector.
7. Connect the device via a Gigabit Ethernet connector.
8. Power up the computer.
The GIE64+ can be installed in a PCI Express x4, x8, or x16
slot
NOTE:
Hardware Installation
9
This page intentionally left blank.
10
Hardware Installation
GIE64+
Important Safety Instructions
For user safety, please read and follow all instructions,
WARNINGS, CAUTIONS, and NOTES marked in this manual
and on the associated equipment before handling/operating the
equipment.
X
Read these safety instructions carefully.
X
Keep this user’s manual for future reference.
X
Read the specifications section of this manual for detailed
information on the operating environment of this equipment.
X
When installing/mounting or uninstalling/removing
equipment:
Z
X
Turn off power and unplug any power cords/cables.
To avoid electrical shock and/or damage to equipment:
Z
Keep equipment away from water or liquid sources;
Z
Keep equipment away from high heat or high humidity;
Z
Keep equipment properly ventilated (do not block or
cover ventilation openings);
Z
Make sure to use recommended voltage and power
source settings;
Z
Always install and operate equipment near an easily
accessible electrical socket-outlet;
Z
Secure the power cord (do not place any object on/over
the power cord);
Z
Only install/attach and operate equipment on stable
surfaces and/or recommended mountings; and,
Z
If the equipment will not be used for long periods of time,
turn off and unplug the equipment from its power source.
Important Safety Instructions
11
X
Never attempt to fix the equipment. Equipment should only
be serviced by qualified personnel.
A Lithium-type battery may be provided for uninterrupted, backup
or emergency power.
WARNING:
X
12
Risk of explosion if battery is replaced with one of an incorrect
type. Dispose of used batteries appropriately.
Equipment must be serviced by authorized technicians
when:
Z
The power cord or plug is damaged;
Z
Liquid has penetrated the equipment;
Z
It has been exposed to high humidity/moisture;
Z
It is not functioning or does not function according to the
user’s manual;
Z
It has been dropped and/or damaged; and/or,
Z
It has an obvious sign of breakage.
Important Safety Instructions
GIE64+
Getting Service
Contact us should you require any service or assistance.
ADLINK Technology, Inc.
Address: 9F, No.166 Jian Yi Road, Zhonghe District
New Taipei City 235, Taiwan
ᄅ‫ؑק‬խࡉ೴৬ԫሁ 166 ᇆ 9 ᑔ
Tel:
+886-2-8226-5877
Fax:
+886-2-8226-5717
Email:
service@adlinktech.com
Ampro ADLINK Technology, Inc.
Address: 5215 Hellyer Avenue, #110, San Jose, CA 95138, USA
Tel:
+1-408-360-0200
Toll Free: +1-800-966-5200 (USA only)
Fax:
+1-408-360-0222
Email:
info@adlinktech.com
ADLINK Technology (China) Co., Ltd.
Address: Ϟ⍋Ꮦ⌺ϰᮄऎᓴ∳催⾥ᡔುऎ㢇᯹䏃 300 ো(201203)
300 Fang Chun Rd., Zhangjiang Hi-Tech Park,
Pudong New Area, Shanghai, 201203 China
Tel:
+86-21-5132-8988
Fax:
+86-21-5132-3588
Email:
market@adlinktech.com
ADLINK Technology Beijing
Address: ࣫ҀᏖ⍋⎔ऎϞഄϰ䏃 1 োⲜ߯ࡼ࡯໻ॺ E ᑻ 801 ᅸ(100085)
Rm. 801, Power Creative E, No. 1, B/D
Shang Di East Rd., Beijing, 100085 China
Tel:
+86-10-5885-8666
Fax:
+86-10-5885-8625
Email:
market@adlinktech.com
ADLINK Technology Shenzhen
Address: ⏅ഇᏖफቅऎ⾥ᡔುफऎ催ᮄफϗ䘧᭄ᄫᡔᴃು
A1 ᷟ 2 ὐ C ऎ (518057)
2F, C Block, Bldg. A1, Cyber-Tech Zone, Gao Xin Ave. Sec. 7,
High-Tech Industrial Park S., Shenzhen, 518054 China
Tel:
+86-755-2643-4858
Fax:
+86-755-2664-6353
Email:
market@adlinktech.com
Getting Service
13
ADLINK Technology, Inc. (French Liaison Office)
Address: 15 rue Emile Baudot, 91300 Massy CEDEX, France
Tel:
+33 (0) 1 60 12 35 66
Fax:
+33 (0) 1 60 12 35 66
Email:
france@adlinktech.com
ADLINK Technology Japan Corporation
Address: ͱ101-0045 ᵅҀ䛑गҷ⬄ऎ⼲⬄䤯‫ ⬎ފ‬3-7-4
⼲⬄ 374 ɛɳ 4F
KANDA374 Bldg. 4F, 3-7-4 Kanda Kajicho,
Chiyoda-ku, Tokyo 101-0045, Japan
Tel:
+81-3-4455-3722
Fax:
+81-3-5209-6013
Email:
japan@adlinktech.com
ADLINK Technology, Inc. (Korean Liaison Office)
Address: 昢殾柢 昢爎割 昢爎壟 1675-12 微汾瘶捒娯 8 猻
8F Mointer B/D,1675-12, Seocho-Dong, Seocho-Gu,
Seoul 137-070, Korea
Tel:
+82-2-2057-0565
Fax:
+82-2-2057-0563
Email:
korea@adlinktech.com
ADLINK Technology Singapore Pte. Ltd.
Address: 84 Genting Lane #07-02A, Cityneon Design Centre,
Singapore 349584
Tel:
+65-6844-2261
Fax:
+65-6844-2263
Email:
singapore@adlinktech.com
ADLINK Technology Singapore Pte. Ltd. (Indian Liaison Office)
Address: 1st Floor, #50-56 (Between 16th/17th Cross) Margosa Plaza,
Margosa Main Road, Malleswaram, Bangalore-560055, India
Tel:
+91-80-65605817, +91-80-42246107
Fax:
+91-80-23464606
Email:
india@adlinktech.com
ADLINK Technology, Inc. (Israeli Liaison Office)
Address: 6 Hasadna St., Kfar Saba 44424, Israel
Tel:
+972-9-7446541
Fax:
+972-9-7446542
Email:
israel@adlinktech.com
14
Getting Service