Kenmore Deluxe 625.384650 Owner's Manual

Add to my manuals
12 Pages

advertisement

Kenmore Deluxe 625.384650 Owner's Manual | Manualzz

OWNER'S

MANUAL

MODEL NO.

625.384650

Caution:

Read and Follow

All Safety Rules,

Installation and

Operating

Instructions

Before First Use of This Product.

DELUXE DUAL-STAGE

DRINKING WATER SYSTEM

If you have questions when installing and using your drinking water filter system, call this toll-free number...

1 - 800 - 426 - 9345 www.KenmoreWater.com

SAVE THIS MANUAL

• Safety Guides

Installation

• Operation

• Cartridge Replacement

• Repair Parts

System tested and certified by NSF International to

ANSl/NSF Standard 42 and 53 for the reduction of the claims specified on the performance data sheet.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA

SAFETY GUIDES / SPECIFICATIONS

• Read all steps and guides carefully before installing and using your undersink drinking water filter system.

Follow all steps exactly to correctly install.

Reading this manual will also help you to get all the benefits from the undersink drinking water filter system.

Use the filter on a potable, safe-todrink home

COLD water supply only.

The filter cartridge will not purify water, or make it safe to drink.

DO NOT use on HOT water (100°F, max.).

Do not use with water that is microbiologically known quality without adequate unsafe or of un- disinfection before or after the system.

This system is certified for cyst reduction and may be used on disinfected waters that may contain filterable cysts.

• Check with your local public works department

for plumbing and sanitation codes.

You must follow their guides as you install the system.

Follow your local codes if they differ with guides in this manual.

Massachusetts

In Massachusetts, shall be adhered plumbing to.

codes

Consult of with your licensed plumber.

• The undersink drinking water filter system works on water pressures of 30 psi (minimum) to 100 psi (maximum).

the maximum,

If your install house a pressure water pressure reducing the water supply pipe to the filter system.

is over valve in

• specifications forms.

Read the other limits (pH, hardness, etc.) in the and be sure your water supply con-

• Protect the undersink drinking water filter system and piping from freezing.

Water freezing in the housing will break it.

Min. - Max. Supply Water Pressure

Min. - Max. Supply Water Temperature

Inlet - Outlet

Rated Service Flow

30 - 100 psi

40 - 100 "F

3/8" fittings and tubing included

0.6 gpm at 60 psi

\

WARRANTY

FULL ONE YEAR WARRANTY ON UNDERSINK DRINKING WATER FILTER SYSTEM

For one year from the date of purchase, Sears will replace this Undersink Drinking Water Filter System (except filter cartridges, which are purchased separately), free of charge, if defective in material or workmanship.

WARRANTY IS AVAILABLE BY SIMPLY RETURNING THE UNDERSlNK DRINKING WATER FILTER

SYSTEM TO THE NEAREST SEARS STORE THROUGHOUT THE UNITED STATES.

This warranty gives you specific legal rights, and you may have other rights which vary from state to state.

Sears, Roebuck and Co., DEPT. 817 WA, Hoffman Estates, IL 60179

TABLE OF CONTENTS

Parts of the System / Typical Installation

Materials Needed ................................................

Drawing / Tools

Drinking Water Filter System Installation ...........................

Installing Supply Fitting .....................................

Installing Faucet ............................................

Making Tubing Connections ..................................

Using the Filtered Water System ...................................

Filter Cartridge Life / Replacement .................................

Repair Parts ...................................................

and

4

5 - 7

5

5 - 6

7

8

8 - 9

10 - 11

Locate the water filter housing on the cold water supply pipe, under the kitchen or bathroom sink, to filter the cold drinking water.

Refer to the following drawing.

FILTERING WATER TO ONE FAUCET filtered water faucet kitchen sink

COLD

FILTER I FILTER II

DRINKING WATER

FILTER SYSTEM

PARTS OF THE SYSTEM

filter system assembly including mounting bracket and screws water supply fitting ing filtered water faucet for sink or countertop mount-

3/8" tubing to make all needed connections

MATERIALS AND TOOLS NEEDED

• plumbers putty

• Phillips screwdrivers

• pliers and adjustable

• tubing cutter jaw wrench

• pipe joint compound or Teflon tape

• electric drill and 1" drill bit if mounting needed for the faucet, see page 6 hole is

CAUTION: To avoid damaging the sink, consult a qualified plumber or installer for drilling procedures in porcelain or stainless steel.

TYPICAL UNDERSINK INSTALLATION

FIG. 1

filtered water faucet

\

\

- - _

WATER

OUT

HOT/_ COLD shutoff valve

Note: To change the filter cartridge, you must turn offthe water and release pressure by opening the faucet. A nearby shutoff valve is convenient.

Most sinks already have shutoff valves on the supply pipes.

\

\ supply fitting

" _ tubing

WATER

IN

Monitor

Cable

Filter I

J

/

Filter II

Note: Be sure to allow a minimum space of 1 - 1/2" under the system for removing the sumps, to change the cartridges.

15-1/2" rain.

up from floor

INSTALLATION STEPS

STEP 1 - COLD WATER SUPPLY FITTING

Check and comply with local plumbing codes as you plan, then install a cold feed (supply) water fitting.

The fitting must provide a leak- tight connection to the water filter 3 / 8" tubing. A typical connection using the included water supply fitting is shown in FIG.2 - A. An optional connection using standard plumbing fittings

(not included), is shown in B.

A.

WATER SUPPLY FITTING

1. Close the house main water shutoff valve and open faucets to drain water from the sink cold water pipe.

2. Remove nut that connects the cold water faucet to cold water plumbing.

3. Use pipe joint compound or Teflon tape on cold water faucet stud threads and on the male threads of the water supply fitting that connect to the cold water pipe.

4.

Thread water supply fitting onto pipe and reconnect nut to bottom of fitting.

B. OPTIONAL

(compression

PIPE type

FITTINGS shown)

Note: Be sure to turn off the water supply and open a low faucet to drain the pipe.

Complying with plumbing codes, install a fitting on the cold water pipe to adapt 3 / 8" OD tubing.

A typical connection is shown in figure 2B. If threaded fittings are used, be sure to use pipe joint compound or

Teflon tape on outside threads.

FIG. 2

A, WATER SUPPLY CONNECTION

(using included water supply fitting)

B.

WATER SUPPLY TYPICAL CONNECTION

(using compression fitting)

- parts not included faucet stud

cold water t water supply fitting

/

3/8" tubing to

Water Filter inlet

: co,d

_ia;eer I I

J f

3/8" compression fitting insert ferrule cold water pipe

3/8" tubing to

Water Filter inlet cold water shutoff

INSTALLATION STEPS

STEP 2 - MAKE HOLE FOR FILTERED

WATER FAUCET

Select one of the following places to install the faucet.

Be sure there's room the needed connections.

underneath so you can make

-In an existing sink spray attachment

-Drill a hole in the sink top.

- Drill a hole in the countertop next hole.

to the sink.

1. If drilling is needed make a 1" to 1-1/4" diameter hole for the faucet.

CAUTION: To avoid damaging the sink, consult a qualified plumber or installer for drilling procedures in porcelain or stainless steel.

Special drill bits are made for this.

2. Place plumbers putty around the drilled hole to prevent water leaks around the faucet.

FIG. 3

,

p,umber

putty

....

....

1" to 1- 1/4" diameter hole through sink or countertop

STEP 3 - ASSEMBLE

INSTALL FAUCET

AND

1. Faucet, FIG. 4:

1. Remove the large nut from the faucet threads.

2. Slide the faucet stud and telephone through the sink or countertop hole.

style wire

3. On the underside of the sink or countertop, screw the nut on the faucet threads with the wire running through the slot in the washer.

Tighten the nut so the faucet cannot move, but do not overtighten.

4. Connect tubing to push to connect fitting on bottom of faucet stud per instructions on page 7.

5. Connect the telephone style wire to the recepticle on PWA board in the manifold and route the wiring through slots in top cover and manifold assembly.

FIG. 4

ASSEMBLED IN

MOUNTING HOLE

....

hole in sink or countertop plumbers faucet & spout

/ gasket

_'_-----

TUBING FROM DRINKING <_:71/

WATER SYSTEM

\ slotted washer nut

INSTALLATION STEPS

STEP 4 - MAKE TUBING CONNECTIONS

1. Allowing some slack, measure and cut a length of

3/8" tubing to connect between the supply fitting and the filter system inlet, FIG. 1. Cut the ends of the tubing square.

2. Insert tubing all the way into the supply fitting and inlet fitting.

Pull on the tubing to be sure that it's held firmly in the fitting.

3. Repeat steps I and 2 to connect tubing between the filter system outlet and the adaptor on the bottom of the faucet stud, FIG.

1.

TUBING CONNECTION

(all pushin fitting locations)

This system includes pushin fittings for quick tubing connection at most locations.

If working with the fittings do the following.

Connection, FIG. 5 - A:

1. Use a sharp cutter or knife to cut the end of tubing square.

2. Inspect the end (about 1") of the tubing to be sure there are no nicks, scratches or other rough spots.

If needed cut the tubing again.

3. Push tubing through the collet and all the way into fitting.

Full engagement is 11/16" for 1/4" tubing, and 3/4" for 3/8" tubing.

If tubing other than supplied with the system is used, be sure it is of high quality, exact size and roundness with a smooth surface.

To Disconnect Tubing, FIG.

5 - B: Push the collet inward and hold with a finger while pulling the tubing out.

FIG. 5 - A

Tubing correctly cut and connected cut tubing s_uare t :

I I

I end of tubing round and smooth, with no cuts, nicks or flat spots

FIG. 5 - B

engagement

_E3/4" (3/8" tubing)

-4_ l cotlet (depress to remove tubing)

I

r

CAUTION

I DO NOT USE VINEGAR, OR OTHER ACID I

I BASED CLEANERS ON THIS SYSTEM.

THEY I

I WILL DEGRADE SOME SYSTEM PARTS.

ALI

I WAYS USE SOAP AND WATER.

I- ....................

J

I

1

I

STEP 5 - FILTER CARTRIDGE INSTALLATION

Turn to page 9 and follow all steps under "Filter Cartridge Replacement".

A taste and odor cartridge contains activated carbon, a black powder.

After the new cartridge is installed, open the filtered water faucet and allow fine, harmless carbon particles to purge when you no longer see the "fines" in the filtered water, or approximately from the cartridge.

2- 3 minutes.

Close the faucet

USING THE SYSTEM

The sink or countertop faucet has a hand operated knob to access drinking water.

Turning the knob to the left opens the faucet, turning to the fight shuts off the faucet.

Z faucet filtered water

FAUCET ELECTRONICS

The Undersink Drinking Water Filter will monitor the total water flow of the unit and also length of time the filters have been installed.

The faucet base has an indicator light that flashes to inform you of the status of the filters.

Green Filters are good.

Amber Warning, filters need repladng shortly.

Filters need replacing, when water has been drawn, after 168 days (or 960 gallons have been used) since battery change.

Red - Filters must be replaced.

Will flash after 14 additional days

(or 80 additional gallons).

When the two "AA" batteries are first applied at initial start up, the LED indicator light will flash in a amber, green, red sequence.

reset to zero.

All timers and counters are

In order to reset the monitor time and gallon count feature, the batteries should be removed for a minimum of five seconds and then reinserted.

only"AA" alkalinebatteries.

Improper placement of batteries could damage electronics.

Use care when inserting batteries to align them correctly in manifold with the proper polarity.

If the faucet LED indicator light does not function after a battery change, and the batteries are known to be good and installed properly, there may be a residual charge on the static protection device.

To dissipate this charge, remove the batteries for one hour.

Batteries need to be replaced once a year at the time of filter replacement.

Do not mix battery types, use

FILTER CARTRIDGE

/ USEFUL

LIFE / REPLACEMENT

FILTER CARTRIDGE LIFE

Several variables determine will last. These include: how long a cartridge

1. how much water you use

2. how much sediment, unwanted substance, taste and/or is in the water odor, or other

Use the following information as a guide.

However, no matter which type of cartridge you are using, you will know it is time to replace it when you first notice the return water.

of the unwanted substance in your

8

Kenmore system model 625.384650

with replacement elements 42-38466 has been tested and certified by NSF International for the reduction of chlorine, lead, asbestos, cysts, VOC's and MTBE.

The rated capacity for this system is 1040 gallons.

FILTER CARTRIDGE REPLACEMENT

CAUTION: Never remove sumps with water pressure in the filter system.

1. Close the water supply shut-off valve (FIG. 1, page 4) to the filter.

Open the filtered water faucet

to relieve pressure in the system.

2. Turn the sump off of the filter head, to the left or clockwise 1/4 turn. Be careful, the sump is full of wa-

ter. Do not lose the large o-ring seal.

FIG. 6

ca_ridge head o-ring seal

S

TURN

SUMP

CLOCKWISE

TO REMOVE

Filter

I

TURN

SUMP

COUNTER-

CLOCKWISE

TO TIGHTEN

Filter

II

3. Be sure the inside of the sump is clean.

Use hot, soapy water and rinse thoroughly.

4. Remove the wrapper from the new filter cartridge and insert the filter cartridge in the sump.

Be sure the two o-rings are towards the filter head.

Note: If you are installing two different types of filter cartridges, be sure to install in filters I and II as the guideline on page 3 shows.

5. Lightly lubricate the o- ring seal in the sump with silicone grease or Vaseline.

Be sure it is fully seated in its groove.

6. Hold the sump up to the filter head aligning the protrusion on the cartridge with the center hole in the bottom of the head.

Note: If the sump will not tighten up to the head you may have the cartridge in upside down.

Take the cartridge out and check for correct orientation.

7. Turn (counterclockwise) head 1/4 turn.

the sump onto the filter

8. Repeat steps 2 through 7 at the other filter.

9. Open the filtered water faucet.

Then, slowly open the water supply valve and allow the filter housing to fill.

10. Close the filtered water faucet.

Check for leaks between the sump and the head.

11. Remove and replace batteries to reset counter and timer.

Note: If leaking, turn off the water supply and open the filtered water faucet to depressurize the filter.

Then disassemble the filter and check the o-ring for cuts, flat spots, etc., and sealing surfaces for foreign material.

Clean the o-ring and lubricate with silicone grease or Vaseline.

Carefully press the o- ring into the groove in the sump.

12. Taste and Odor Cartridges: A taste and odor cartridge contains activated carbon, a black powder.

When new, open the filtered water faucet and allow fine, harmless carbon particles to purge from the cartridge.

Close the faucet when you no longer see the

"fines" in the filtered water, or approximately minutes.

2-3

9

REPAIR PARTS

Kenmore Deluxe Dual-Stage Drinking Water System, Model No. 625.384650

I

_6

7

5

2

1 lO

REPAIR PARTS LIST

KEY

NO.

5

6

7

8

9

10

1

2

3

4

11

_1,

41,

PART

NUMBER

7221128

7223633

42-38466

9006062

9041700

7234210

7234228

7234252

7234286

7226495

7228536

7157280

7227467

DESCRIPTION

Sump (2 req.)

O-Ring (2 req.)

Filter, Carbon Block (2 Pack)

Screw (2 req.)

Hanger Washer (2 req.)

Paddlewheel & O-Ring Kit

Paddlewheet Cover & Screw Kit

Rep'l Pwa (includes screw)

Cover, Manifold

Faucet

Feed Supply Fitting

Tubing, 3/8" x 20' - white

Owners Manual

_1, not illustrated

11

OWNERS

MANUAL

UNDERSINK DRINKING

WATER FILTER

SYSTEM

MODEL NO.

625.384650

For the repair or replacement parts you need

Call 7 am - 7 pm, 7 days a week

1 - 800 - 366 - PART

(1 - 800 - 366 - 7278)

The model number of your drinking water filter system is found on the rating decal, located on the back of the post filter.

When requesting service or ordering parts, always provide the following information:

4, Product Type

4, Model Number

4, Part Number

4, Part Description

www.KenmoreWater.com

For in-home major brand repair service

Call 24 hours a day, 7 days a week

1 - 800 - 4 - REPAIR

(1 - 800 - 473 - 7247)

For the location of a

Sears Repair Service Center in your area

Call 24 hours a day, 7 days a week

1 -800-488-1222

For information on purchasing a Sears

Maintenance Agreement, or to inquire about an existing Agreement

Call 9 am - 5 pm, Monday - Saturday

1 - 800 - 827 - 6655

SEARS

I; t: ;'.v/;l.J-t; i _,__l

America's Repair Specialists

======

SEARS

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

7227467 (Rev. C 05/11/01)

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement