Kenwood DDX 8026 BT Installation Guide

Add to my manuals
12 Pages

advertisement

Kenwood DDX 8026 BT Installation Guide | Manualzz
GPS NAVIGATION SYSTEM
SYSTÈME DE NAVIGATION GPS
GPS-NAVIGATIONSSYSTEM
GPS-NAVIGATIESYSTEEM
SISTEMA DI NAVIGAZIONE GPS
SISTEMA DE NAVEGACIÓN GPS
SISTEMA DE NAVEGAÇÃO GPS
DNX SERIES
DNX9260BT
MONITOR WITH DVD RECEIVER
MONITEUR AVEC RÉCEPTEUR DVD
MONITOR MIT DVD-RECEIVER
MONITOR MET DVD-ONTVANGER
MONITOR CON RICEVITORE DVD
MONITOR CON RECEPTOR DVD
MONITOR COM RECEPTOR DVD
DDX SERIES
DDX8026BT
INSTALLATION MANUAL
MANUEL D'INSTALLATION
INSTALLATION-HANDBUCH
INSTALLATIEHANDLEIDING
MANUALE DI INSTALLAZIONE
MANUAL DE INSTALACIÓN
MANUAL DE INSTALAÇÃO
© B54-4775-00/00 (EW)
Accessories
1
Installation Procedure
9
..........1
2
..........1
0
..........1
3
DNX9260BT only
..........1
!
..........1
4
..........1
5
..........2
6
..........1
1. To prevent short circuits, remove the key
from the ignition and disconnect the terminal of the battery.
2. Make the proper input and output wire
connections for each unit.
3. Connect the wire on the wiring harness.
4. Take Connector B on the wiring harness
and connect it to the speaker connector in
your vehicle.
5. Take Connector A on the wiring harness
and connect it to the external power
connector on your vehicle.
6. Connect the wiring harness connector to
the unit.
7. Install the unit in your car.
8. Reconnect the - terminal of the battery.
9. Press the reset button.
10. Perform the Initial Setup. (Refer to the
Instruction Manual.)
2WARNING
• If you connect the ignition wire (red) and the
battery wire (yellow) to the car chassis (ground),
you may cause a short circuit, that in turn may
start a fire. Always connect those wires to the
power source running through the fuse box.
• Do not cut out the fuse from the ignition wire
(red) and the battery wire (yellow). The power
supply must be connected to the wires via the
fuse.
Acquiring GPS Signals
..........1
7
DNX9260BT only
..........1
8
The first time you turn on DNX9260BT, you
must wait while the system acquires satellite
signals for the first time. This process could
take up to several minutes. Make sure your
vehicle is outdoors in an open area away from
tall buildings and trees for fastest acquisition.
After the system acquires satellites for the
first time, it will acquire satellites quickly each
time thereafter.
About the Front Panel
DNX9260BT only
..........1
2
When removing the product from the
box or installing it, the front panel may be
positioned at the angle shown in (Fig. 1). This
DNX SERIES/ DDX SERIES
is due to the characteristics of a mechanism
the product is equipped with.
If the program that is activated when the
product is first powered on works properly,
the front panel will automatically move into
the position (initial setting angle) shown in
(Fig. 2).
(Fig. 1)
(Fig. 2)
After the Installation
After the installation, perform the Initial Setup
by referring to the instruction manual.
¤
• Mounting and wiring this product requires
skills and experience. For safety’s sake, leave the
mounting and wiring work to professionals.
• Make sure to ground the unit to a negative 12V
DC power supply.
• Do not install the unit in a spot exposed to direct
sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of
water splashing.
• Do not use your own screws. Use only the screws
provided. If you use the wrong screws, you could
damage the unit.
• If the power is not turned ON (“PROTECT” is
displayed), the speaker wire may have a shortcircuit or touched the chassis of the vehicle and
the protection function may have been activated.
Therefore, the speaker wire should be checked.
• If your car’s ignition does not have an ACC
position, connect the ignition wires to a power
source that can be turned on and off with the
ignition key. If you connect the ignition wire to a
power source with a constant voltage supply, as
with battery wires, the battery may die.
• If the console has a lid, make sure to install the
unit so that the faceplate will not hit the lid when
closing and opening.
• If the fuse blows, first make sure the wires aren’t
touching to cause a short circuit, then replace the
old fuse with one with the same rating.
• Insulate unconnected wires with vinyl tape or
other similar material. To prevent a short circuit,
do not remove the caps on the ends of the
unconnected wires or the terminals.
• Connect the speaker wires correctly to the
terminals to which they correspond. The unit may
be damaged or fail to work if you share the wires or ground them to any metal part in the car.
• When only two speakers are being connected
to the system, connect the connectors either to
both the front output terminals or to both the
rear output terminals (do not mix front and rear).
For example, if you connect the + connector
of the left speaker to a front output terminal, do
not connect the - connector to a rear output
terminal.
• After the unit is installed, check whether the brake
lamps, blinkers, wipers, etc. on the car are working
properly.
• Mount the unit so that the mounting angle is 30°
or less.
• This unit has the cooling fan (page 5) to decrease
the internal temperature. Do not mount the unit
in a place where the cooling fan of the unit are
blocked. Blocking these openings will inhibit the
cooling of the internal temperature and result in
malfunction.
• Do not press hard on the panel surface when
installing the unit to the vehicle. Otherwise scars,
damage, or failure may result.
• Reception may drop if there are metal objects
near the Bluetooth antenna.
Bluetooth antenna unit
¤ CAUTION
Install this unit in the console of your
vehicle.
Do not touch the metal part of this unit
during and shortly after the use of the
unit. Metal part such as the heat sink and
enclosure become hot.
English
3
Connection
Connector A
Ground wire (Black)
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Battery wire (Yellow)
Ignition wire (Red)
Antenna Cord
Connector B
(Orange/White)
⁄
FM/AM antenna
input (JASO)
Dimmer control wire (Orange/White)
Connect to the vehicle's parking brake
detection switch harness.
ILLUMI
Parking sensor wire (Light Green)
PRK SW
For the sake of safety, be sure to connect the parking sensor.
Connect to vehicle's reverse lamp harness when
using the optional rear view camera.
⁄
To steering remote
To use the steering wheel remote control feature, you need to an
exclusive remote adapter (not supplied) matches your car is required.
When this terminal is not in use, leave its cap on.
Connect to the terminal that is grounded when either
the telephone rings or during conversation.
⁄
To connect the Kenwood navigation system,
consult your navigation manual.
Connect either to the power control terminal when using the optional
power amplifier, or to the antenna control terminal in the vehicle.
⁄
4
If no connections are made, do not let the cable come out from the tab.
DNX SERIES/ DDX SERIES
Bluetooth Microphone (Accessory 9)
(see page 9)
Voice Control Switch (Accessory 0)
(DNX9260BT only) (see page 9)
Cooling fan
GPS Antenna (Accessory 7)
(DNX9260BT only) (see page 9)
FUSE (15A )
Accessory 1
Reverse sensor wire (Purple/White)
REVERSE
Steering remote control input (Light Blue/Yellow)
REMOTE CONT
STEERING WHEEL
REMOTE INPUT
Mute control wire (Brown)
MUTE
Power control/ Motor antenna control wire (Blue/White)
ANT. CONT
P.CONT
English
5
Connecting Wires to Terminals
Connector Function Guide
Pin Numbers for
ISO Connectors
External Power
Connector
A-4
A-5
A-6
A-7
A-8
Cable Colour Functions
Yellow
Blue/White
Orange/White
Red
Black
Speaker
Connector
B-1
B-2
B-3
B-4
B-5
B-6
B-7
B-8
Battery
Power Control
Dimmer
Ignition (ACC)
Earth (Ground)
Connection
Purple
Purple/Black
Gray
Gray/Black
White
White/Black
Green
Green/Black
Rear Right (+)
Rear Right (–)
Front Right (+)
Front Right (–)
Front Left (+)
Front Left (–)
Rear Left (+)
Rear Left (–)
2WARNING
Connecting the ISO Connector
The pin arrangement for the ISO connectors
depends on the type of vehicle you drive. Make sure
to make the proper connections to prevent damage
to the unit.
The default connection for the wiring harness is
described in 1 below. If the ISO connector pins
are set as described in 2, make the connection as
illustrated.
Please be sure to reconnect the cable as shown
2 below to install this unit to the Volkswagen
vehicles etc.
1 (Default setting) The A-7 pin (red) of the
vehicle’s ISO connector is linked with
the ignition, and the A-4 pin (yellow) is
connected to the constant power supply.
Ignition cable (Red)
Unit
Battery cable (Yellow)
A-7 Pin (Red)
Vehicle
A-4 Pin (Yellow)
2 The A-7 pin (red) of the vehicle’s ISO
connector is connected to the constant
power supply, and the A-4 pin (yellow) is
linked to the ignition.
Ignition cable (Red)
Unit
Battery cable (Yellow)
6
A-7 Pin (Red)
Vehicle
A-4 Pin (Yellow)
DNX SERIES/ DDX SERIES
System Connection
iPod (commercially available)
USB terminal
iPod
USB device (commercially available)
Audio input (iPod/AV Input 3 switchable)
Resistance-free stereo type mini plug (3.5φ)
Visual input (iPod/AV Input 3 switchable)
Resistance-free mini plug (3.5φ)
To Camera
control terminal
Audio/Visual Input
• Visual input (Yellow)
• Audio left input (White)
• Audio right input (Red)
Audio/Visual Input
• Visual input (Yellow)
• Audio left input (White)
• Audio right input (Red)
(Blue/Red)
CENTER
SUB
WOOFER
REAR
RELAY 2
RELAY 1
(Blue/Red)
FRONT
To Relay Box
REAR VIEW
CAMERA
(Green/Red)
(Green/White)
Audio/Visual Output
• Visual output (Yellow)
• Audio left output (White)
• Audio right output (Red)
AV IN1
Accessory 2
AV OUT
Accessory 4
AV IN 2
Accessory 3
Rear View Camera Input
• Visual input (Yellow)
Front Preout
• Audio left output (White)
• Audio right output (Red)
Rear Preout
• Audio left output (White)
• Audio right output (Red)
Subwoofer Preout
• Audio left output (White)
• Audio right output (Red)
Center Preout
English
7
Optional Accessory Connection
iPod
(commercially available)
KCA-iP301V
(Optional Accessory)
Visual Output (Yellow)
iPod
Audio Output (Black)
USB terminal
DDX8026BT only
USB terminal
USB device
(commercially available)
TV Tuner
(Optional Accessory)
Navigation System
(Optional Accessory)
(DDX8026BT only)
Connection cable
(Included in the
Navigation System)
TV ANTENNA INPUT
TO MONITOR UNIT
Connection cable
(Included in the TV tuner)
units that can be connected to this unit.
⁄ Navigation
(As of December, 2009):
• KNA-G620T
For latest information, access the
www.kenwood.com/cs/ce/.
8
DNX SERIES/ DDX SERIES
Installing the GPS Antenna
(DNX9260BT only)
Installing the Talk Switch (DNX9260BT
only) and the Microphone Unit
GPS antenna is installed inside of the car. It
should be installed as horizontally as possible
to allow easy reception of the GPS satellite
signals.
To mount the GPS antenna inside your
vehicle:
1. Clean your dashboard or other surface.
2. Peel the backing off of the adhesive on the
bottom of the metal plate (accessory 8).
3. Press the metal plate (accessory 8)
down firmly on your dashboard or other
mounting surface. You can bend the
metal plate (accessory 8) to conform to a
curved surface, if necessary.
4. Place the GPS antenna (accessory 7) on
top of the metal plate (accessory 8).
1. Check the installation position of the
microphone (accessory 9) and the Talk
switch (accessory 0).
2. Remove oil and other dirt from the
installation surface.
3. Install the microphone.
4. Wire the microphone cable up to the unit
with it secured at several positions using
tape or the like.
Accessory 9
Accessory 0
Accessory 7
Accessory 8
Fix a cable with a commercial item of tape.
¤
• Depending on the type of car, reception of the
GPS satellite signals might not be possible with an
inside installation.
• The GPS antenna should be installed at a position
that is spaced at least 12 inch (30 cm) from cellular
phone or other transmitting antennas. Signals
from the GPS satellite may be interfered with by
these types of communication.
• Painting the GPS antenna with (metallic) paint
may cause a drop in performance.
Peel the release coated paper of double-face
adhesive tape to fix on the place shown above.
Adjust the direction of the microphone to the driver.
⁄
Install the microphone as far as possible
from the cell-phone.
English
9
Installation for Monitor/Player Unit
Installing the Escutcheon
Attaching the monitor panel
1. Attach accessory 6 to the unit.
Accessory !
Accessory 6
Installing the Monitor/Player
Unit
Hold the monitor panel securely so as not to
drop it accidentally.
Fit the monitor panel onto the attaching plate
until it is firmly locked.
1
1
2
Bend the tabs of the mounting sleeve
with a screwdriver or similar utensil and
attach it in place.
3
⁄
• Make sure that the unit is installed securely in
place. If the unit is unstable, it may malfunction
(eg, the sound may skip).
10
DNX SERIES/ DDX SERIES
Removing Monitor/Player Unit
Removing the Hard Rubber
Frame (escutcheon)
1. Engage the catch pins on the removal tool
5 and remove the two locks on the lower
level.
Lower the frame and pull it forward as
shown in the figure.
Removing the Unit
1. Remove the hard rubber frame by referring
to the removal procedure in the section
<Removing the Hard Rubber Frame>.
2. Insert the two removal tools 5 deeply into
the slots on each side, as shown.
Accessory 5
Accessory 5
Catch
Lock
⁄
3. Lower the removal tool toward the
bottom, and pull out the unit halfway
while pressing towards the inside.
• The frame can be removed from the top side in
the same manner.
2. When the lower level is removed, remove
the upper two locations.
⁄
• Be careful to avoid injury from the catch pins on
the removal tool.
4. Pull the unit all the way out with your
hands, being careful not to drop it.
English
11

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement