- Computers & electronics
- Audio & home theatre
- Video line amplifiers
- Kramer Electronics
- VS-211H
- User manual
advertisement
K R A ME R E LE CT R O N IC S L T D .
USER MANUAL
MODEL:
VS-211H
Automatic HDMI Standby
Switcher
P/N: 2900-000681 Rev 6
Contents
Achieving the Best Performance
Defining the VS-211H Automatic HDMI Standby Switcher
Selecting the Default Master Source Signal
Connecting the REMOTE Terminal Block Connector
Figures
Figure 1: VS-211H Automatic HDMI Standby Switcher
Figure 3: REMOTE Terminal Block Connector
VS-211H – Contents i
1 Introduction
Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world of unique, creative, and affordable solutions to the vast range of problems that confront the video, audio, presentation, and broadcasting professional on a daily basis. In recent years, we have redesigned and upgraded most of our line, making the best even better!
Our 1,000-plus different models now appear in 11 groups that are clearly defined by function: GROUP 1: Distribution Amplifiers; GROUP 2: Switchers and Routers;
GROUP 3: Control Systems; GROUP 4: Format/Standards Converters; GROUP 5:
Range Extenders and Repeaters; GROUP 6: Specialty AV Products; GROUP 7:
Scan Converters and Scalers; GROUP 8: Cables and Connectors; GROUP 9:
Room Connectivity; GROUP 10: Accessories and Rack Adapters and GROUP 11:
Sierra Products.
Congratulations on purchasing your Kramer VS-211H Automatic HDMI Standby
Switcher, which is ideal for:
Providing backup switching for broadcast and post-production applications.
VS-211H - Introduction 1
2 Getting Started
We recommend that you:
Unpack the equipment carefully and save the original box and packaging materials for possible future shipment
Review the contents of this user manual i
Go to http://www.kramerelectronics.com/support/product_downloads.asp
to check for up-to-date user manuals, application programs, and to check if firmware upgrades are available (where appropriate).
2.1 Achieving the Best Performance
To achieve the best performance:
Use only good quality connection cables (we recommend Kramer highperformance, high-resolution cables) to avoid interference, deterioration in signal quality due to poor matching, and elevated noise levels (often associated with low quality cables)
Do not secure the cables in tight bundles or roll the slack into tight coils
Avoid interference from neighboring electrical appliances that may adversely influence signal quality
Position your Kramer VS-211H away from moisture, excessive sunlight and dust
!
This equipment is to be used only inside a building. It may only be connected to other equipment that is installed inside a building.
2 VS-211H - Getting Started
2.2 Safety Instructions
!
Caution: There are no operator serviceable parts inside the unit
Warning: Use only the Kramer Electronics input power wall adapter that is provided with the unit
Warning: Disconnect the power and unplug the unit from the wall before installing
2.3 Recycling Kramer Products
The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC aims to reduce the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected and recycled. To comply with the WEEE Directive,
Kramer Electronics has made arrangements with the European Advanced
Recycling Network (EARN) and will cover any costs of treatment, recycling and recovery of waste Kramer Electronics branded equipment on arrival at the EARN facility. For details of Kramer’s recycling arrangements in your particular country go to our recycling pages at http://www.kramerelectronics.com/support/recycling/ .
VS-211H - Getting Started 3
4
3 Overview
The VS-211H is a high-performance automatic standby switcher for HDMI video signals. The VS-211H automatically switches to the secondary input whenever the primary video signal is interrupted. If the primary signal reappears, the unit automatically switches back to the primary input.
In addition, the VS-211H features:
A maximum data rate of up to 6.75Gbps (2.25Gbps per graphic channel)
HDTV compatibility
HDCP and HDMI compliance
3D pass through
EDID PassThru that passes EDID signals from source to display
A DEFAULT INPUT switch for selecting the default HDMI master source signal
Contact closure remote control for forced operation
Active switching
VS-211H - Overview
3.1 Defining the VS-211H Automatic HDMI Standby
Switcher
This section defines the VS-211H.
Figure 1: VS-211H Automatic HDMI Standby Switcher
5
6
7
#
1
2
3
4
8
Feature
ACTIVE INPUT 1,2 LEDs
ON LED
OUT HDMI Connector
IN 1 HDMI Connector
IN 2 HDMI Connector
DEFAULT INPUT Switch
REMOTE IN 1 and IN 2 Terminal
Block Connectors
5V DC
Function
Illuminate when input is active
Illuminates when receiving power
Connects to the HDMI output acceptor
Connects to the HDMI input source 1
Connects to the HDMI input source 2
Switches to select the default input (IN 1 or IN 2)
Connect to a contact closure switch
+5V DC connector for powering the unit
VS-211H - Overview 5
4 Using the VS-211H
This section describes how to:
Connect the VS-211H (see Section 4.1
Select the default master source signal (see Section
Connect the REMOTE connector (see Section 4.3
4.1 Connecting the VS-211H
i
Always switch off the power to each device before connecting it to your
VS-211H. After connecting your VS-211H, connect its power and then switch on the power to each device.
To connect the VS-211H, as illustrated in the example in Figure 2 , do the following:
1. Connect the IN 1 HDMI connector to the HDMI input source 1 (for example,
DVD player 1).
2. Connect HDMI input source 2 (for example, DVD player 2) to the IN 2 HDMI connector.
3. Connect HDMI acceptor (for example, an LCD display) to the OUT HDMI connector.
4. Set the DEFAULT INPUT switch to whichever input is the master input, as
5. If needed, connect the remote switches to the REMOTE IN 1 and IN 2
terminal block connectors, as described in Section 4.3
6. Connect the 5V DC power adapter to the power socket and connect the adapter to the mains electricity.
6 VS-211H - Using the VS-211H
Figure 2: VS-211H Connections
4.2 Selecting the Default Master Source Signal
When active input sources are connected to IN 1 and IN 2, the DEFAULT INPUT switch setting determines the default master input source.
If the master input signal is not detected, the VS-211H automatically activates the standby input:
If IN 1 is the default input and it fails, IN 2 activates
If IN 2 is the default input and it fails, IN 1 activates
If the master input reactivates while the standby input is active, the unit automatically switches back to the master input:
If IN 2 is active while IN 1 is the default input, when IN 1 reactivates, it is switched to the output
If IN 1 is active while IN 2 is the default input, when IN 2 reactivates, it is switched to the output
VS-211H - Using the VS-211H 7
4.3 Connecting the REMOTE Terminal Block Connector
Regardless of the default input switch setting, you can force the switching of the active input by remote control. To do this, connect the appropriate REMOTE input
terminal block connector pins to a contact closure switch (see Figure 3 ).
Note that the connection should be permanent, since the VS-211H reverts to an automatic switcher when the connection is removed.
To force IN 1: connect REMOTE IN1 to PIN G (ground)
To force IN 2: connect REMOTE IN2 to PIN G (ground) i
Do not connect both the REMOTE IN1 and the REMOTE IN2 to PIN G simultaneously
Attach PIN IN1 to
PIN G to activate
INPUT 1
Attach PIN IN2 to
PIN G to activate
INPUT 2
Figure 3: REMOTE Terminal Block Connector
Note: The contact closure setting remains in effect until an event occurs such as changing the default input switch or connecting or attaching an HDMI device.
8 VS-211H - Using the VS-211H
5 Technical Specifications
INPUTS:
OUTPUT:
DATA RATE:
STANDARDS COMPLIANCE:
CONTROLS:
POWER CONSUMPTION:
OPERATING TEMPERATURE:
STORAGE TEMPERATURE:
HUMIDITY:
DIMENSIONS:
WEIGHT:
ACCESSORIES:
OPTIONS:
2 HDMI on HDMI connectors
1 HDMI on an HDMI connector
Supports 2.25Gbps per graphic channel
HDCP and HDMI
Contact closure remote control, input default selection switch
5V DC, 780mA
0° to +40°C (32° to 104°F)
-40° to +70°C (-40° to 158°F)
10% to 90%, RHL non-condensing
12cm x 7.2cm x 2.4cm (4.7" x 2.8" x 1.0") W, D, H
0.3kg (0.7lbs)
Power supply, mounting bracket
RK-3T 19" rack adapter
Specifications are subject to change without notice at http://www.kramerelectronics.com
VS-211H - Technical Specifications 9
For the latest information on our products and a list of Kramer distributors, visit our Web site where updates to this user manual may be found.
We welcome your questions, comments, and feedback.
Web site: www.kramerelectronics.com
E-mail: [email protected]
!
SAFETY WARNING
Disconnect the unit from the power supply before opening and servicing
Rev: 6 P/N: 2900- 000681
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project