Land Pride PD25 Series User's Manual

Post Hole Diggers
Specifications & Capacities
Post Hole Diggers
PD10 and PD15 Series
Tractor HP Range
Weight Without Auger
Auger Length
PD10
PD15
15 to 30 HP
20 to 40 HP
120 lbs.
161 lbs.
30"
48"
Auger Flight Thickness
1/4”
Auger Pipe
2 1/2" ID
Auger Teeth
Forged, Individually Replaceable
40 Degree angle installed on flat side
50 Degree angle installed on angled side
Number of Teeth
6" - 2 teeth
9" & 12" - 4 teeth
Pilot
Cast steel, 3 drill points
Driveline
Cat. II Shearbolt
Maximum Operating PTO Speed
300 RPM
Gearbox
540 RPM 3:1 Ratio
Output Shaft
540 RPM 3.18:1 Ratio
2" O.D. Round
3-Point Hitch Cat.
Cat. I
Boom Tube
2 7/8” O.D.
Yoke Tube
2 7/8” O.D.
Options and Accessories
Auger Sizes (Options)
6”, 9”, or 12”
Auger Extensions (Accessories)
6”, 9”, or 12”
7" & 14" Extensions Available
Not Available
Not Available
Hydraulic Down Pressure Kit
Available
Available
Storage Stand
Available
Available
PD10 = 52 1/2" w/ 12" Auger
PD15 = 66 1/4" w/ 12" Auger
Cat. III Torque Limiter Driveline
PD10 = 31 1/2"
PD15 = 32"
PD10 = 58 5/8"
PD15 = 77 5/8"
PD10 = 70"
PD15 = 89 1/2"
26776
Designs, specifications, features and information are subject to change without notice.
50
317-048S continued on next page
2/03/09
Specifications & Capacities
Post Hole Diggers
PD25 and PD35 Series
Tractor HP Range
Weight Without Auger
PD25
PD35
25 to 55 HP
30 to 75 HP
186 lbs.
233 lbs.
Auger Length
48"
Auger Flight Thickness
1/4”
Auger Pipe
2 1/2" ID
Auger Tooth Construction
Number of Teeth
Forged, Individually Replaceable
40 Degree angle installed on flat side
50 Degree angle installed on angled side
(6” - 2 teeth) (9” & 12” - 4 teeth) (15” - 5 teeth) (18” - 6 teeth) (24” - 8 teeth)‘
Pilot
Cast steel, 3 drill points
Driveline Cat.
Cat. III Shear bolt - Standard
Cat. III Radial pin clutch - Optional (Recommended on Auger Sizes 15" and above.)
Maximum Operating PTO Speed
300 RPM
Gearbox
540 RPM 3.18:1 Ratio
Output Shaft
540 RPM 4:1 Ratio
2" O.D. Round
3-Point Hitch Cat.
Cat. I & II
Boom Tube
3 1/2” O.D.
Yoke Tube
3 1/2” O.D.
2 7/8” O.D.
Options and Accessories
Auger Sizes (Options)
6”, 9”, 12”, 14”, 18”, or 24”
Auger Extensions (Accessories)
7" & 14" Extensions Available
Available
Available
Hydraulic Down Pressure Kit
Available
Available
Storage Stand
Available
Available
PD25 & PD35 = 68 1/2" w/ 12" Auger
Cat. III Torque Limiter Driveline
PD25/35 = 33 1/4"
PD25 = 78 1/8"
PD35 = 79 3/8"
PD25 = 89 1/8"
PD35 = 90 3/8"
26776
Designs, specifications, features and information are subject to change without notice.
51
317-048S end
2/03/09