Lenovo B5 User manual

Initial setup instructions

1) Adjust the angle for the best viewing experience. It can be rotated between 15 degrees and 35 degrees from the vertical position.

15° min.

35° max.

3) Connect the power cord to the computer and the electrical outlet as shown below.

All-in-One Desktop PC

Unpack

1. Computer 2. Mouse 3. Power cord 4. Keyboard 5. User manual

6. Remote control (Selected models only)

1 2 3

The computer stand must remain installed at all times to ensure maximum system stability.

Make sure the angle of the computer is at least 15 degrees from the vertical position; otherwise the computer will be unstable and could fall over.

To open the computer stand, refer to the illustration:

2) If the computer is configured with a wired keyboard and mouse, connect the keyboard and mouse cables to the appropriate keyboard (PS/2 connector) and mouse connectors (USB connector).

If the computer is configured with a wireless keyboard and mouse, setup the keyboard and mouse wireless connection.(For more details refer to the back of this poster).

4)

Press the power button on the side of the computer to turn it on.

4 5 6

Version: 1.1

Touch buttons

The buttons located at the bottom-right-side of the screen are touch buttons. Press on any of the buttons ONCE to turn the indicator light ON to activate them. The buttons remain active while the indicator light is ON. Now, press on any of the buttons to change settings as desired. The indicator light turns off automatically after

10 seconds of inactivity.

Wireless keyboard and mouse configuration

Method

A

1. Install the batteries.

Close

Put 2 AA batteries in the keyboard's battery compartment.

2 AA batteries

Put 2 AA batteries in the battery compartment, making sure the position of the polarities is identical to the image.

3. Press the wireless connect button.

OFF ST

ATE

2 AA batteries

While the computer is turned off, press the wireless connect button on the back of the keyboard and mouse.

5. Establish the wireless connection automatically.

Once the wireless connection is successfully established, the indicator lights on the keyboard and mouse will turn off and they will work properly.

2. Turn on the power switch.

Turn on the mouse power switch.

If you do not plan to use the mouse for a long time, turn off the mouse power switch to save battery life.

After installing the batteries, turn on the power switch on the side of the keyboard.

4. Make sure the indicator lights blink and then turn on the computer.

If the wireless keyboard and mouse fail to connect according to method

A, follow method B:

Method

B

1. Make sure the indicator lights blink.

Make sure the wireless indicator lights still blink. If they stop blinking, press the connect button on the back of keyboard and mouse again.

2. Press the wireless reset button until wireless connection established.

To establish the wireless connection, press and hold the wireless reset button for over 5 seconds until you hear multiple beep sounds.

The wireless reset button is a touch button located at the bottom-right-side of the screen, as shown in the diagram. Before following the reset instructions, make sure the indicator light is ON. Press on any of the touch buttons ONCE to turn the indicator light ON to activate the buttons.

If connection is not established successfully, refer to "Wireless keyboard and mouse instructions" in the User Guide.

When the keyboard and mouse wireless indicator lights blink white, turn the computer on within 30 seconds to establish a wireless connection.

Notes:

1) When establishing a wireless connection, it is recommended to keep the distance from the keyboard/mouse to the computer less than 25 cm (10 inches)

2) The effective working distance of the wireless keyboard and mouse is 10 m (33 feet) (depending on the computer's working environment).

If the wireless device does not work, do the following:

1. Be sure there is no physical obstacle between the wireless device and the computer.

2. Restart the computer, and verify that the system devices are functional.

3. Repeat the procedure for establishing a Bluetooth connection.

4. Replace the batteries.

5. Do not place the computer under a metal surface or table.

6. Make sure there are no electronic devices close by, such as speakers, remote controls of electronic toys or mobiles, which might create high electromagnetic fields that could interrupt the wireless connection.

7. Place the keyboard, mouse and remote control the right way up.

8. Remove the batteries from the keyboard, mouse and remote control if you do not plan to use them for a long time.

9. If the batteries in the keyboard, mouse or remote control leak, clean the battery compartments as soon as possible and insert new batteries.

10. Use batteries of good quality to ensure the proper functioning of the remote control.

11. When battery power becomes low, the battery indicator light on the keyboard will change from orange to red.

12

4

LVT

Computer instructions

Built-in microphone

Camera

Wireless reset button (or

Indicator lights ON/OFF button)

Volume down

Volume up

Brightness down

Brightness up

LCD On/Off

2

3

5

6

1

1

2

3

4

5

6

Ċ!

Optical drive

Ċ!

Power button

Ċ!

Card reader

Ċ!

USB ports (2)

Ċ!

Headphone connector

Ċ!

Microphone connector

7

8

9

10

11

7 Ċ!

AV-IN connector (Selected models only)

8

9

Ċ!

PS/2 Keyboard connector

Ċ!

Ethernet connector

10 Ċ!

USB ports (2)

11 Ċ!

TV-Tuner connector (Selected models only)

12 Ċ!

Power connector

LVT :

After entering Windows, press this key to launch the LVT (Lenovo Vantage

Technology) program, Lenovo's pre-loaded Home PC software. In addition to its own functions, the LVT program will allow you to start other Windows compatible software, specially configured to run on this model of computer.