Model number
Serial number
:
:
LG DLP PROJECTOR
Please read this manual carefully before operating
your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the bottom of the set and
quote this information to your dealer when you
require service.
BX220-JD
OWNER’S MANUAL
DLP PROJECTOR
FCC NOTICE
• A Class A digital device
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Warning
This is a class A product. In a domestic environment this product may cause radio interference, in
which case the user may be required to take adequate measures.
Contents
Contents
Introduction
Safety Instructions ..........................................4-6
Names of parts
Main Body .......................................................7
Connecting Part ..............................................7
Control Panel ..................................................8
Remote Control ...............................................9
Installing Batteries...........................................9
Projector Status Indicators..............................10
Accessories.....................................................11
Optional Extras ...............................................11
Screen Menu Options
Auto Tracking Function ...................................25
Clock / Phase Function ...................................25
Screen Position ...............................................25
RS-232C
External Control Device Setup........................26
Information
Supported Monitor Display..............................31
Maintenance....................................................32
Memo ..............................................................33
Specifications ..................................................35
Installing and Composition
Installation Instructions ...................................12
Basic Operation of the Projector.....................13
Using Kensington Security System.................14
Turning on the Projector .................................15
Turning off the Projector .................................15
Focus and Position of the Screen Image........16
Selecting source mode ...................................16
Connection
Connecting
Connecting
Connecting
Connecting
Connecting
to
to
to
to
to
a
a
a
a
a
Desktop PC ..........................17
Notebook PC ........................17
Video Source ........................18
DVD ......................................18
D-TV Set-Top Box ................18
Function
Video Menu Options
Adjusting Video ...............................................19
APC (Auto Picture Control) .............................19
Auto Color Temperature Control .....................20
White Peaking Function ..................................20
Gamma Function ............................................20
Special Menu Options
Selecting language .........................................21
Flip Horizontal Function ..................................21
Flip Vertical Function.......................................21
Using ARC Function........................................22
Using Keystone function .................................22
Auto Source Function .....................................22
Using Blank function .......................................23
Selecting Blank Image color ...........................23
Lamp Mode Function ......................................23
Checking lamp time ........................................24
Using Still function ..........................................24
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is attached to a product it
means the product is covered by the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately
from the municipal waste stream via designated collection facilities
appointed by the government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential
negative consequences for the environment and human health.
4. For more detailed information about disposal of your old appliance,
please contact your city office, waste disposal service or the shop
where you purchased the product.
3
Safety Instructions
Safety Instructions
Please take note of the safety instructions to prevent any potential accident or misuse of the projector.
➟ Safety Instructions are given in two forms as detailed below.
WARNING : The violation of this instruction may cause serious injuries and even death.
NOTES : The violation of this instruction may cause light injuries or damage to the projector.
➟ After reading this manual, keep it in the place that the user always can contact easily.
Indoor Installation
Do not place the Projector in direct
sunlight or near heat sources such
as radiators, fires and stove etc.
This may cause a fire hazard !
WARNING
Do not place inflammable materials beside the projector
Do not allow children to hang on
the installed projector.
This may cause a fire hazard !
It may cause the projector to fall, causing injury or death.
Indoor Installation
Disconnect from the mains and
remove all connections before
moving.
NOTES
Do not place the projector close
to sources of steam or oil such
as a humidifier.
Do not place the projector where
it might be exposed to dust.
This may cause a fire hazard !
This may create a fire hazard or an
electric shock hazard !
When installing the projector on a
table, be careful not to place it
near the edge.
This may cause the projector to fall
causing serious injury to a child or
adult and serious damage to the
projector.
Only use a suitable stand.
Only use the projector on a level
and stable surface.
It may become unstable and affect
operation.
Ensure good ventilation around the
projector. The distance between
the projector and the wall should
be more than 20cm/8 inches.
An excessive increase in its internal temperature may cause a fire
hazard!
Do not block the vents of the projector or restrict air-flow in any way.
Do not place the projector directly on a carpet, rug or place where
ventilation is restricted.
This would cause the internal temperature to increase and could cause a fire
hazard!
This would cause its internal temperature to increase and might create a fire
hazard !
Outdoor Installation
WARNING
Do not use the projector in a damp place such as a bathroom where it is likely to get wet.
This may cause a fire or an electric shock hazard !
Power
Earth wire should be connected.
If the earth wire is not connected, there is a
possible danger of electric shock caused by
the current leakage.
If grounding methods are not possible, a
separate circuit breaker should be employed
and installed by a qualified electrician.
Do not connect ground to telephone wires,
lightning rods or gas pipe.
4
WARNING
The mains plug should be inserted fully into the power outlet to
avoid a fire hazard !
This may cause a fire hazard !
Do not place heavy objects on
the power cord
This may cause a fire or an electric
shock hazard !
Safety Instructions
WARNING
ENGLISH
Power
Do not use too many plugs on the Mains multi-outlet.
It may result in overheating of the outlet and causes a fire hazard !
Power
Never touch the power plug with
a wet hand
This may cause an electric shock
hazard !
Do not plug when the power cord
or the plug is damaged or the
connecting part of the power outlet is loose.
This may cause a fire or an electric
shock hazard !
NOTES
Hold the plug firmly when unplugging. If you pull the cord the cord
may be damaged.
Prevent dust collecting on the
power plug pins or outlet.
This may cause a fire hazard !
This may cause a fire hazard !
Ensure the power cord does not
come into contact with sharp or
hot objects such as a heater.
Place the projector where people
will not trip or tread on the power
lead.
This may cause a fire or an electric
shock hazard !
This may cause a fire or an electric
shock hazard !
Do not turn the projector On/Off by plugging-in or unplugging the power plug to the wall outlet.
(Do not use the power plug for switch.)
It may cause mechanical failure or could give an electric shock.
Using
Do not place anything containing
liquid on top of the projector such
as flowerpot, cup, cosmetics or
candle.
This may cause a fire hazard !
WARNING
In case of impact shock or damage to the projector switch it off
and unplug it from the mains outlet and contact your service center.
Do not allow any objects to fall
into the projector.
This may cause an electric shock
hazard !
This may cause a fire or an electric
shock hazard !
If water is spilt into the projector
unplug it from the mains supply
outlet immediately and consult
your Service Agent.
This may cause an electric shock hazard !
Do not remove any covers
(except lens cover). High risk of
Electric Shock!
Dispose of used batteries carefully and safely.
In the case of a battery being
swallowed by a child please consult a
doctor immediately.
In the event that an image does
not appear on the screen please
switch it off and unplug it from
the mains supply and contact
your Service Agent.
This may cause a fire or an electric
shock hazard !
Don’t look directly onto the lens
when the projector is in use. Eye
damage may occur!
Do not touch metal parts during or
soon after operation since the
vents and lamp cover will remain
very hot!
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit; that is,a single outlet circuit which
powers only that appliance and has no additional outlets or branch circuits.Check the specification page
of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets,loose or damaged wall outlets, extension cords,
frayed power cords,or damaged or cracked wire insulation are dangerous.Any of these conditions could
result in electric shock or fire. Periodically examine the cord of your appliance,and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced
with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched,
closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the
cord exits the appliance.
5
Safety Instructions
Using
Never touch the wall outlet when
there is leakage of gas, open the
windows and ventilate.
It can cause a fire or a burn by a
spark.
WARNING
Do not drop the projector or allow
impact shock.
This may cause mechanical failure or
personal injury !
Using
Do not place heavy objects on
top of projector.
This may cause mechanical failure or
personal injury!
Don’t look at laser beam directly
as it can cause eye damage!
NOTES
Take care not to cause impact to
the lens particularly when moving
the projector.
Do not touch the lens of the projector. It is delicate and easily
damaged.
Do not use any sharp tools on the projector as this will damage the casing.
Cleaning
Do not use water while cleaning
the projector
This may cause damage to the
projector or an electric shock hazard.
WARNING
In the unlikely event of smoke or
a strange smell from the projector, switch it off , unplug it from
the wall outlet and contact your
dealer or service centre.
Use an air spray or soft cloth that
is moist with a neutral detergent
and water for removing dust or
stains on the projection lens.
This may cause a fire or an electric
shock hazard !
Cleaning
Contact the Service Center once
a year to clean the internal parts
of the projector.
NOTES
Unplug this product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners.
This may cause damage to the Projector or cause an electric shock hazard !
Accumulated dust can cause mechanical failure.
Others
WARNING
Do not attempt to service the projector yourself. Contact your dealer or service centre.
This may cause damage to the projector and could give an electric Shock as well as invalidating the warranty !
Others
Be sure to unplug if the projector
is not to be used for a long period.
NOTES
Refer lamp servicing to qualified
service personnel.
Accumulated dust may cause a fire
hazard!
Only use the specified type of battery.
This could cause damage to the remote control.
6
Do not mix new batteries with old
batteries.
This may cause the batteries to overheat and leak.
ENGLISH
Names of parts
Names of parts
Main Body
* The projector is manufactured using high-precision technology. You may, however, see on the Projector
screen tiny black points and/or bright points (red, blue, or green). This can be a normal result of the
manufacturing process and does not always indicate a malfunction.
Rear remote control sensor
Zoom ring
Control panel
Focus ring
Power button
Indicators
Foot adjusting button
R
WE
PO
O
AUT
VOL
MEN
OK
U
VOL
SOU
RCE
Front remote control sensor
Lens cover
* Push the lens cover into the inside after pulling it open into the
front. (If you mount on the ceiling, after pushing the cover, the lens
cover is installed. If not, the cover may overlap projecting lens.)
Foot adjusting button
Connecting Part
DVI Input
S-Video
RGB Input
(PC/DTV)
RS-232C
Video
AC IN
Kensington Security
System Connector
(Refer to page 14)
7
Names of parts
Control Panel
/
, KEYSTONE+/- Button
SOURCE
MENU
KEYSTONE
MENU Button
SOURCE Button
Selects or closes menus.
Switches to RGB, DVI, Video,S-Video mode.
/
Button
Adjusts functions of menus.
AUTO Button
AUTO
OK
POWER Button
POWER
8
A
KEYSTONE
OK Button
Checks present mode and
saves the change of functions.
ENGLISH
Names of parts
Remote Control
POWER
POWER Button
MENU
KEYSTONE
SOURCE
MENU Button
F
SOURCE Button
KEYSTONE+/-,
/ G Button
AUTO Button (Refer to p.25)
A
AUTO
KEYSTONE
BLANK
LASER
D
/
EButton
OK Button
OK
ARC Button (Refer to p.22)
BLANK Button (Refer to p.23)
ARC
STILL Button (Refer to p.24)
STILL
LASER Button
* Produces a bright red laser pointer on the
screen for the purpose of indication.
(Don’t look at laser beam directly as it
can cause eye damage!)
Installing Batteries
• Open the battery compartment cover on the back of the
remote control and insert the batteries with correct polarity,
match “+” with “+”, and match “-” with “-”.
• Install two 1.5V “AAA” batteries.
Don’t mix used batteries with new batteries.
9
Names of parts
Projector Status Indicators
* Lamp Indicator, operation indicator and temperature indicator at the top of the projector show the user the operating status
of the projector.
Lamp Indicator
Operation Indicator Temperature Indicator
PO
AU
VO
ME
TO
WE
R
L
OK
NU
VO
SO
UR
L
CE
Operation Indicator
Orange
Green(flashing)
Green
Orange(flashing)
Off
Red
Lamp Indicator
Red(flashing)
Green(flashing)
Orange
Temperature Indicator Red
Red (flashing)
10
Standby.
Lamp cooling until the lamp turn on.
On operation. (Turn on the lamp)
Projector lamp is cooling as power out (2 minutes)
Power off.
Projector lamp is reaching the end of its life and needs
to be replaced with a new lamp. (over 2000 hours)
The projector has trouble in the lamp or around it at
power-on. Retry Power On again later. If lamp indicator
is red (flashing) again, contact the service center.
The lamp cover is not closed.
This projector is in high temperature. Turn the power of
projector off and check the ventilator.
The projector is turned off as its high temperature.
Power has turned off due to problem with the
internal cooling fan. Contact your service center.
ENGLISH
Names of parts
Accessories
POWER
MENU
KEYSTONE
AUTO
KEYSTONE
BLANK
LASER
SOURCE
OK
ARC
STILL
1.5V
1.5V
Remote Control
Computer Cable
2 Batteries (size AAA)
RCA to D-Sub Adaptor
Power Cord
Video Cable
Operating guide
Optional Extras
*
*
*
*
Contact your dealer to purchase these items.
When applying a ceiling installer, use only the ceiling installer for projector.
Contact your service personnel for replacing a new lamp.
Projector lamp is reaching the end of its life and needs to be replaced with a new lamp.
Projection Screen
Lamp
SCART to RCA jack (option)
Ceiling installer for projector
Portable Bag
S-Video Cable
DVI-D Cable
RS-232C Cable
11
Installing and Composition
Installation and Composition
Installation Instructions
* Don’t place the projector in the following conditions. It may cause malfunction or product damage.
Provide proper ventilation for this projector.
●The projector is equipped with ventilation holes(intake)
●Do not place the projector on a carpet, rug or other
●Never push projector or spill liquid of any kind into the
●Leave an adequate distance(30cm/12 inches or
on the bottom and ventilation holes(exhaust) on the front.
do not block or place anything near these holes, or internal
heat build-up may occur, causing picture degradation or
damage to the projector.
projector.
similar surface. It may prevent a adequate ventilation
of the projector bottom. This product should be
mounted to a wall or ceiling only.
more) around the projector.
Place this projector in adequate temperature and humidity conditions.
● Install this projector only in a location where adequate temperature and humidity is available. (refer p.35)
Don’t place the projector where it can be covered with dust.
● This may cause overheating of the projector.
Do not obstruct the slots and openings of the projector. This may cause overheating and create a fire
hazard.
The projector is manufactured using high-precision technology. You may, however, see tiny black points
and/or bright points (red, blue, or green) that continuously appear on the projector Screen. This is a normal result of the manufacturing process and does not indicate a malfunction.
To display DTV programs, it is necessary to connect a DTV receiver (Set-top Box) and connect it to the
projector.
If there is no input signal, the Menu will not be displayed on screen.
12
ENGLISH
Installing and Composition
Basic Operation of the Projector
1.Place the projector on a sturdy and horizontal surface with the PC or AV source.
2.Place the projector the correct distance from the screen. The distance between the projector and the
screen determines the actual size of the image.
3.Position the projector so that the lens is set at a right angle to the screen. If the projector is not set at a right
angle, the screen image will be crooked. If this is so then the keystone adjustment may correct this (Refer to
page 22.)
4.Connect the cables of the projector to a wall power socket and other connected sources.
projection distance based on the picture format
Projection off-set ratio:100%
Screen height (X)
Center line of lens
Projection distance (D)
4:3 picture format
mm / inches
screen
size
40″
60″
80″
90″
100″
110″
120″
150″
200″
screen
height (X)
610/24.0
914/36.0
1219/48.0
1372/54.0
1524/60.0
1676/66.0
1829/72.0
2286/90.0
3048/120.0
The shortest
distance (D) 1400/55.1
2100/82.7
2800/110.2
3150/124.0
3500/137.8
3850/151.6
4200/165.4
5250/206.7
7000/275.6
The longest
1680/66.1
distance (D)
2520/99.2
3360/132.3
3780/148.8
4200/165.4
4620/181.9
5040/198.4
6300/248.0
8400/330.7
* The longest/shortest distance show status when adjusted by the zoom function.
13
Installing and Composition
Using Kensington Security System
● The projector has a ‘Kensington’ Security System Connector on the back panel. Connect the ‘Kensington’
Security system cable as below.
● For the detailed installation and use of the Kensington Security System, refer to the user’s guide attached
to the Kensington Security System set.
And for further information, contact http://www.kensington.com, the internet homepage of the
Kensington company that deals with expensive electronic equipments such as notebook PCs or projectors.
● Kensington Security System is an optional item.
K
14
ENGLISH
Installing and Composition
Turning on the Projector
1. Connect power cord correctly.
2. Remove the lens cover of the projector.
3. Press the POWER button on the remote control or top cover.
(Green operation indicator flashes during cooling of the lamp.)
●
●
●
●
It will take about 12 second to display the picture after power on because the projector lamp has to warm up.
An image will appear after the operation indicator light turns (Green).
Select the source mode with the SOURCE button.
Leave the projector plugged in for at least 2 minutes after switching off the projector, as this will allow the lamp
cooling to continue which will help to preserve the lamp life.
* Don’t unplug the power cord while the ventilation fan (inlet/outlet) is working. If so, you take longer time by lamp on.
Turning off the Projector
1. Press the POWER button on the top cover or remote control.
2. Press the POWER button on the top cover or remote control again to cut off the power.
3. If the operation indicator LED is orange and blinking, do not disconnect the mains supply until the
operation indicator LED is lit up constantly (orange).
● If the operation indicator LED is orange and blinking, the power button on the top cover or on the remote control will not
operate.
Power Off?
Please Press
Key Again.
15
Installing and Composition
Focus and Position of the Screen Image
When an image appears on the screen, check if it is in focus and fits well to the screen.
Zoom ring
Focus ring
POWE
AUTO
R
VOL
MENU
OK
VOL
SOURC
E
● To adjust the focus of the image, rotate the focus ring which is the outer ring on the lens.
● To adjust the size of the image, rotate the zoom ring which is the inner ring on the lens.
To raise or lower the image on the screen, extend or retract the foot at the bottom of the projector
by pushing foot adjuster button as below.
1. While pressing the foot adjuster button, raise or lower the projector to place the screen image in the proper position.
2. Release the button to lock the foot in its new position.
3. To fine-tune the height of the projector, rotate the front foot to raise or lower it.
After raising the front foot, do not press down on the projector.
Selecting source mode
1. Press the SOURCE button.
select
F
RGB
OK
G
2. Each press of the F, G button changes the display as below.
16
RGB
DVI
S-Video
Video
ENGLISH
Connection
Connection
Connecting to a Desktop PC
*
*
*
*
You can connect the projector to a computer of VGA, SVGA, XGA and SXGA output.
You can use ARC function for the RGB signals of the Aspect Ration 4:3. (For HD wide input signals, you cannot use ARC function.)
Fundamentally, HD wide input signal is not included in the Spec, so the set may not support HD signal perfectly.
Refer to page 31 for the supported pc graphic card displays of the projector.
< How to connect >
a. Connect computer cable to RGB Input (PC/DTV) of the
projector.
b. If the PC has DVI output, connect DVI cable to DVI Input
of the projector.
Connecting to a Notebook PC
< How to connect >
a. Connect computer cable to RGB Input (PC/DTV) of the
projector.
* If you set your computer, such as a notebook type IBM PC/AT
compatible, to output the signal to both the display of your
computer and the external monitor, the picture of the external
monitor may not appear properly. In such cases, set the output
mode of your computer to output the signal only to the external
monitor. For details, refer to the operating instructions supplied
with your computer.
b. If the PC has DVI output, connect DVI cable to DVI Input
of the projector.
17
Connection
Connecting to a Video Source
* You can connect a VTR, a camcorder, a LDP or any other compatible video image source to the projector.
< How to connect 1 >
a. Connect the Video input jacks of the projector to the output
jacks of the A/V source with Video cable.
<VCR>
< How to connect 2 >
S VIDEO
(R) AUDIO (L)
b. Connect the S-Video input jack of the projector to the
S-Video output jack of an A/V source with an S-Video cable.
* You can get better picture quality when connecting
S-Video source to the projector.
VIDEO
OUT
IN
Connecting to a DVD
* The output jacks (Y, PB, PR) of the DVD might be labelled as Y, Pb, Pr / Y, B-Y, R-Y / Y, Cb, Cr according to the equipment.
< How to connect >
a. Connect the DVD Component cable to the RCA to D-Sub
Adaptor and then connect the RCA to D-Sub Adaptor to
RGB Input (PC/DTV) of the projector.
RCA to D-Sub Adaptor
Component cable
* When connecting the component cable, match the jack colors
with the component cable.(Y=green, PB=blue, PR=red)
b. Use a DVD with Component 480i(576i)/480p(576p) mode.
<DVD>
(R) AUDIO (L)
Y
PB
PR
Connecting to a D-TV Set-Top Box
* To receive D-TV programmes, it is necessary to purchase a D-TV receiver (Set-Top Box) and
connect it to the projector.
* Please refer to the owner's manual of the D-TV Set-Top Box for the connection between projector and
D-TV Set-Top Box.
< How to connect an RGB source >
a. Connect computer cable to RGB Input (PC/DTV) of the
projector.
<D-TV Set-Top Box>
* If the Set-Top Box has DVI output, use DVI cable.
(R) AUDIO (L)
DTV OUTPUT
DVI OUTPUT
PB
Y
PR
b. Use a DTV receiver with DTV 480p(576p)/720p/1080i mode.
* It can be supported the DVI/HDCP.
< How to connect a Component source >
a. Connect the D-TV Set-Top Box Component cable to the
RCA to D-Sub Adaptor and then connect the RCA to D-Sub
Adaptor to RGB Input (PC/DTV) of the projector.
RCA to D-Sub Adaptor
Component cable
* When connecting the component cable, match the jack colors
with the component cable.(Y=green, PB=blue, PR=red)
b. Use a DTV receiver with DTV 480p(576p)/720p/1080i mode.
(R) AUDIO (L)
18
DTV OUTPUT
DVI OUTPUT
Y
PB
PR
ENGLISH
Function
Function
* In this manual, the OSD(On Screen Display) may be different from your Projector’s because it is just example to help with the Projector
operation.
* If there is no input signal present, the Menu will not be displayed on the screen.
* This operating guide explains operation of RGB(PC) mode mainly.
Video Menu Options
Adjusting Video
< RGB mode >
1. Press the MENU button and then use F, G button to select the
menu.
2. Press the OK (A) button and then use D , E button to select a video item you
want to adjust.
Contrast
50
Brightness
50
Color R
50
Color G
50
Color B
50
Reset
3. Press the F, G button to adjust the screen condition as you want.
●
●
●
●
MENU prev.
move
F G adjust
< Video mode >
Each adjustment of
menu options will not affect other input source.
As required, re-adjust
menu options for the following input source :
Video/S-Video/Component (480i(576i)), Component (480p(576p), 720p, 1080i)
To restore the original image condition after changing it, press OK (A) button
after selecting [Reset] item.
In the broadcasting system NTSC, the picture item Tint is displayed and can
be adjusted.
To exit the menu display, repeatedly, press the MENU button.
APC
F
Contrast
80
Clear
Brightness
50
Color
50
Sharpness
50
MENU prev.
move
F G select
APC
F
Clear
Contrast
80
G
APC (Auto Picture Control)
* Use APC to set the projector for the best picture appearance.
* This function will not work in RGB mode.
1. Press the MENU button and then use F, G button to select the
menu.
2. Press the OK (A) button and then use D , E button to select APC item.
3. Press the F, G button to adjust the screen condition as you want.
●
50
Color
50
Sharpness
50
MENU prev.
move
F G select
Each press of the F, G button changes the screen as shown below.
Clear
●
Brightness
G
Soft
User
To exit the menu display, repeatedly, press the MENU button.
19
Function
Video Menu Options
Auto Color Temperature Control
1. Press the MENU button and then use F, G button to select the
menu.
2. Press the OK (A) button and then use D , E button to select ACC item.
3. Press the F, G button to make appropriate adjustments.
●
F
Normal
G
White Peaking
F
10
G
Gamma
F
Normal
G
MENU prev.
move
F G select
Each press of the F, G button changes the screen as shown below.
Normal
●
ACC
Cool
Warm
To exit the menu display, repeatedly, press the MENU button.
White Peaking Function
1. Press the MENU button and then use F, G button to select the
menu.
2. Press the OK (A) button and then use D , E button to select White Peaking item.
ACC
F
Normal
G
White Peaking
F
10
G
Gamma
F
Normal
G
MENU prev.
move
F G select
3. Press the F, G button to adjust the screen condition as you want.
●
The default value may changed based on input mode.
Adjust to higher value to see the bright picture and adjust to lower value to see the
quality picture.
● To exit the menu display, repeatedly, press the MENU button.
●
Gamma Function
1. Press the MENU button and then use F, G button to select the
menu.
2. Press the OK (A) button and then use D , E button to select Gamma item.
ACC
F
Normal
G
White Peaking
F
10
G
Gamma
F
Normal
G
MENU prev.
3. Press the F, G button to adjust the screen condition as you want.
●
Each press of the F, G button changes the screen as shown below.
Normal
●
20
Film
Sports
To exit the menu display, repeatedly, press the MENU button.
move
F G select
ENGLISH
Function
Special Menu Options
Selecting language
1. Press the MENU button and then use F, G button to select the
menu.
2. Press the OK (A) button and then use D , E button to select Language item.
Language
F
English
G
ARC
F
4:3
G
1
G
Flip Horizontal
Flip Vertical
3. Press the F, G button to select the language you want to use.
Set ID
●
On-Screen-Display (OSD) is marked in the selected language from this point.
● To exit the menu display, repeatedly, press the MENU button.
MENU prev.
F
move
F G select
Flip Horizontal Function
* This function reverses the projected image horizontally.
Use this function when rear projecting an image.
1. Press the MENU button and then use F, G button to select the
menu.
Language
2. Press the OK (A) button and then use D , E button to select Flip Horizontal
item.
ARC
F
English
G
F
4:3
G
Press OK to Flip
Flip Horizontal
Flip Vertical
Set ID
MENU prev.
1
F
move
A
G
OK
3. Press the OK (A) button to see reversed image.
●
●
Each time you press the button, the image will be reversed.
To exit the menu display, repeatedly, press the MENU button..
Flip Vertical Function
* This function reverses the projected image vertically.
* When you hang the projector upside down from the ceiling ,
you will need to reverse the image vertically and horizontally.
1. Press the MENU button and then use F, G button to select the
menu.
Language
2. Press the OK (A) button and then use D , E button to select Flip Vertical
item.
ARC
F
English
G
F
4:3
G
Flip Horizontal
Flip Vertical
Set ID
MENU prev.
Press OK to Flip
1
F
move
A
G
OK
3. Press the OK (A) button to see reversed image.
●
●
Each time you press the button, the image will be reversed.
To exit the menu display, repeatedly, press the MENU button.
21
Function
Special Menu Options
Using ARC Function
1. Press the ARC button.
Each press of the button changes the display as below.
F
16 : 9
G
F
16:9
4:3
G
4:3
You can also use this function by using the MENU button.
Using Keystone function
* Use this function when the screen is not at a right angle to the
projector and the image is a trapezoid shape.
* Only use the Keystone function when you can’t get the best
angle of projection, because it may cause a blazing fire of the
screen.
1. Press the KEYSTONE + or KEYSTONE - button.
2. Press the KEYSTONE + or KEYSTONE - button to adjust the screen
condition as you want.
●
Keystone are adjusted from -50 to +50.
●
You can also use this function by using the MENU button.
Keystone
0
Auto Source Function
* Automatically detects the projector input signal.
1. Press the MENU button and then use F, G button to select the
menu.
2. Press the OK (A) button and then use D , E button to select Auto Source item.
Keystone
0
Auto Source
F
Off
G
Blank Image
F
Blue
G
Lamp Mode
F
Normal mode
Lamp Time
3. Press the F, G button to select On or Off.
●
22
To exit the menu display, repeatedly, press the MENU button.
MENU prev.
0 Hr
move
F G select
G
ENGLISH
Function
Using Blank function
* This function may be effective if you need to get attention of the audience
during presentations, meetings or briefings.
1. Press the BLANK button.
● The
●
screen turns off to a background color.
You can choose the background color.
(Refer to ‘Selecting blank image color’)
2. Press any button to cancel the blank function.
Selecting Blank Image color
1. Press the MENU button and then use F, G button to select the
menu.
2. Press the OK (A) button and then use D , E button to select Blank Image
item.
Keystone
F
Off
G
Blank Image
F
Blue
G
Lamp Mode
F
Normal
Lamp Time
3. Press the F, G button to select the color you want to use.
MENU prev.
●
●
0
Auto Source
G
0 Hr
move
F G select
Background color will be changed to the selected Blank function color from this point.
To exit the menu display, repeatedly, press the MENU button.
Lamp Mode Function
1. Press the MENU button and then use F, G button to select the
menu.
2. Press the OK (A) button and then use D , E button to select Lamp Mode item.
3. Press the F, G button to select Normal mode or Silent mode.
●
Keystone
0
Auto Source
F
Off
G
Blank Image
F
Blue
G
Lamp Mode
F
Normal mode
Lamp Time
To exit the menu display, repeatedly, press the MENU button.
MENU prev.
G
0 Hr
move
F G select
23
Function
Special Menu Options
Checking lamp time
1. Press the MENU button and then use F, G button to select the
menu.
● The used lamp time is displayed.
● When projector lamp is reaching the end of its life (over 2000 hours), the lamp indicator will
be turned red.
● The lamp warning LED illuminates red continuously in the case of excessive lamp time.
Keystone
0
Auto Source
F
Off
G
Blank Image
F
Blue
G
Lamp Mode
F
Normal mode
Lamp Time
MENU prev.
Using Still function
1. Press the STILL button.
* You can freeze the input image.
<Moving Image>
<Still Image>
2. To exit Pause, press any button .
* The STILL function would release automatically after about 10 minutes.
24
0 Hr
move
F G adjust
G
ENGLISH
Function
Screen Menu Options
Auto Tracking Function
*This function assures you of getting the best video quality by automatically
adjusting the difference of horizontal size and synchronization of the image.
*Auto Tracking function works in RGB input only.
1. Press the AUTO button.
●
Image positioning and synchronization are automatically adjusted.
Auto Configure
2. Adjust Clock or Phase in
menu after operation of Auto Configure
if you want to get better picture quality in accordance with diverse RGB
input modes. In certain circumstances, you can’t get the best picture
quality only with auto-correction.
You can also use this function by using the MENU button. (Only in RGB mode)
For best results, perform this function while displaying a still image.
Clock / Phase Function
* Clock Function
This function adjusts the horizontal width of the projected image to get the
image to fit on the screen size.
* Phase Function
This function is for the detailed adjustment of the clock function.
* It’s available to adjust [Clock], [Phase] in RGB mode only.
1. Press the MENU button and then use F, G button to select the
2. Press the OK (A) button and then use
Phase item.
3. Press the
●
F, G
D,E
Auto Configure
menu.
button to select Clock or
Clock
0
Phase
15
Horizontal
0
Vertical
0
MENU prev.
move
F G adjust
move
F G adjust
button to adjust the screen condition.
To exit the menu display, repeatedly, press the MENU button.
Screen Position
*If the image size does not fit the screen in accordance with the input
source, set the position of the image by selecting Horizontal / Vertical
position. (RGB mode)
Auto Configure
1. Press the MENU button and then use F, G button to select the
menu.
2. Press the OK (A) button and then use D , E button to select Horizontal or
Vertical item.
Clock
0
Phase
15
Horizontal
0
Vertical
0
MENU prev.
3. Press the F, G button to adjust the screen condition as you want.
●
Horizontal, Vertical are adjusted from -50 to +50.
●
Based on the input mode, the adjustment range may be changed.
To exit the menu display, repeatedly, press the MENU button.
●
25
RS-232C
External Control Device Setup
* Connect the RS-232C input jack to an external control device (such as a computer or a video control system)
and control the Projector’s functions externally.
SET ID
1. Press the MENU button and then use F, G button to select the
menu.
2. Press the OK (A) button and then use D , E button to select Set ID item.
Language
F
English
G
ARC
F
4:3
G
1
G
Flip Horizontal
3. Press the F, G button to adjust Set ID to select the desired projector ID number.
●
The adjustment range of Set ID is 1~99.
Only the projector with the specified ID number will operate from the remote control.
● To exit the menu display, repeatedly, press the MENU button.
●
How to connect external control equipment
• Connect the serial port of the PC to the RS-232C jack on the projector back panel.
• RS-232C cable is not supplied with the projector.
• Use the RS232C cable to control the projector externally (Refer to Fig.1).
<Fig.1, RS-232 Interface Cable>
RXD
TXD
DTR
GND
DSR
RTS
CTS
RXD
TXD
DTR
2
3
4
5
6
7
8
2
3
4
5
6
7
8
External
Device
Projector
GND
DSR
RTS
CTS
* 1, 9 Pin No Connection
Communication Parameter Setup
• Baud Rate : 115200 bps(UART)
• Data Length : 8 bit
• Parity : none
• Stop bit : 1 bit
• Flow Control : none
• Communication code : ASCII code
26
9
5
6
1
Flip Vertical
Set ID
MENU prev.
F
move
F G select
ENGLISH
RS-232C
Command Reference List
01.
02.
03.
04.
05.
06.
07.
08.
09.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Command1
Command2
k
k
k
k
k
k
k
k
k
k
k
k
j
j
j
j
j
x
a
b
c
d
g
h
i
j
k
l
m
u
w
y
z
q
u
b
Power
Input Select
Aspect Ratio
Screen Mute
Contrast
Brightness
Color
Tint
Sharpness
OSD Select
Remote Control Lock / Key Lock
Color Temperature
Red ADC gain adjustment
Green ADC gain adjustment
Blue ADC gain adjustment
Low Power
Auto configuration
Input Select
Data
(Hexadecimal)
0~1
*
1~2
0~1
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0~1
0~1
0~2
0 ~ 64
0 ~ 64
0 ~ 64
0~1
1
*
* This data will be explained in this document in detail.
❑ Communication Protocol
1. Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
* [Command 1]
* [Command 2]
* [Set ID]
* [DATA]
* [Cr]
* [ ]
: First command to control the set.(k, j, x, ASCII code, 1 Character)
: Second command to control the set..(ASCII code, 1 Character)
: You can adjust the set ID to choose desired projector ID number in special menu. See previous page.
Adjustment range is 1 ~ 99. When selecting Set ID ‘0’, every connected projector set is controlled.
: To transmit command data. Transmit 2 character when organized ASCII code.
* Transmit ‘FF’ data to read status of command.
: Carriage Return
ASCII code ‘0x0D’
: ASCII code character correspond to “Space Bar” which is in order to classify command, set ID and Data.
2. OK Acknowledgement
[Command2] [ ] [Set ID] [ ] [OK] [Data] [x]
* The Projector transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is
data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer.
3. Error Acknowledgement
[Command2] [ ] [Set ID] [ ] [NG] [Data] [x]
* The Projector transmits ACK (acknowledgement) based on this format when receiving abnormal data from non-viable
functions or communication errors.
Data : [1] : illegal code(This command is not supported.)
[2] : not support function(This function doesn’t work.)
[3] : wait more time(Try again a few minute later.)
27
RS-232C
External control device setup
01. Power (Command2:a)
03. Aspect Ratio (Command2:c)
➜ To control Power On/Off of the Projector.
➜ To adjust the screen format.
Transmission
Transmission
[k] [a] [ ] [Set ID] [ ] [Data] [Cr]
Data
[k] [c] [ ] [Set ID] [ ] [Data] [Cr]
0 : Power Off
1 : Power On
Data 1 : Normal Screen( 4:3)
2 : Wide Screen(16:9)
Ack
Ack
[a] [ ] [Set ID] [ ] [OK] [Data] [x]
Data
[c] [ ] [Set ID] [ ] [OK] [Data] [x]
Data 1 : Normal Screen( 4:3)
2 : Wide Screen(16:9)
0 : Power Off
1 : Power On
➜ To show Power On/Off status.
Transmission
[k] [a] [ ] [Set ID] [ ] [FF] [Cr]
04. Screen Mute (Command2:d)
Ack
[a] [ ] [Set ID] [ ] [OK] [Data] [x]
Data
➜ To select screen mute on/off.
0 : Power Off
1 : Power On
Transmission
* In like manner, if other functions transmit ‘0xFF’ data based
on this format, Acknowledgement data feed back presents
status about each function.
[k] [d] [ ] [Set ID] [ ] [Data] [Cr]
Data
0 : Screen Mute Off (Picture On)
1 : Screen Mute On (Picture Off)
Ack
[d] [ ] [Set ID] [ ] [OK] [Data] [x]
Data 0 : Screen Mute Off (Picture On)
1 : Screen Mute On (Picture Off)
02. Input Select (Command2:b)
➜ To select input source for the Set.
Transmission
05. Contrast (Command2:g)
[k] [b] [ ] [Set ID] [ ] [Data] [Cr]
Data
2 : Video
6 : RGB-DTV
9 : DVI-PC
3 : S-Video
7 : RGB-PC
4 : Component
8 : DVI-DTV
➜ To adjust screen contrast.
Transmission
[k] [g] [ ] [Set ID] [ ] [Data] [Cr]
Ack
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’.
[b] [ ] [Set ID] [ ] [OK] [Data] [x]
Data
2 : Video
7 : RGB-PC
3 : S-Video
9 : DVI-PC
4 : Component
* The transmission data for RGB-DTV(Data:6) input select is
changed to RGB-PC(Data:7) for the identical mode processing.
In like manner, the data of transmission for DVI-DTV(Data:8)
input select is changed to DVI-PC(Data:9).Therefore,if you send
command to select RGB-DTV or DVI-DTV source,you will recieve
changed data in the Ack message.
Ack
[g] [ ] [Set ID] [ ] [OK] [Data] [x]
Data Min : 0 ~ Max : 64
* Real data mapping 1
0
: Step 0
A : Step 10
* Real data mapping 2
0
: Step -50
32 : Step 0
F : Step 15
28
10
: Step 16
64
: Step 100
64 : Step 50
ENGLISH
RS-232C
06. Brightness (Command2:h)
➜ To adjust screen brightness.
Transmission
[k] [h] [ ] [Set ID] [ ] [Data] [Cr]
10. OSD Select (Command2:l)
➜ To select OSD On/Off.
Transmission
[k] [ l ] [ ] [Set ID] [ ] [Data] [Cr]
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’.
Data
Ack
[h] [ ] [Set ID] [ ] [OK] [Data] [x]
Ack
[ l ] [ ] [Set ID] [ ] [OK] [Data] [x]
Data
Min : 0 ~ Max : 64
Data
0 : OSD Select Mode Off
1 : OSD Select Mode On
0 : OSD Select Mode Off
1 : OSD Select Mode On
07. Color (Command2:i)
➜ To adjust the screen color.
Transmission
[k] [ i ] [ ] [Set ID] [ ] [Data] [Cr]
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’.
➜ To lock the front panel controls on the
projector and remote control.
Transmission
Ack
[ i ] [ ] [Set ID] [ ] [OK] [Data] [x]
Data
11. Remote Control Lock/Key Lock
(Command2:m)
Min : 0 ~ Max : 64
[k] [m] [ ] [Set ID] [ ] [Data] [Cr]
Data
0 : Lock Off
1 : Lock On
Ack
[m] [ ] [Set ID] [ ] [OK] [Data] [x]
Data
08. Tint (Command2:j)
➜ To adjust the screen tint.
0 : Lock Off
1 : Lock On
* If you're not using the remote control, use this mode.
When main power is On/Off, external control lock is released.
Transmission
[k] [ j ] [ ] [Set ID] [ ] [Data] [Cr]
Data Red : 0 ~ Green : 64
* Refer to ‘Real data mapping2’.
Ack
[ j ] [ ] [Set ID] [ ] [OK] [Data] [x]
Data
Red : 0 ~ Green : 64
12. Color Temperature (ACC) (Command2:u)
➜ Adjust the color temperature.
Transmission
09. Sharpness (Command2:k)
[k] [u] [ ] [Set ID] [ ] [Data] [Cr]
➜ To adjust the screen sharpness.
Data
Transmission
Ack
[u] [ ] [Set ID] [ ] [OK] [Data] [x]
[k] [k] [ ] [Set ID] [ ] [Data] [Cr]
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’.
Data
0 : Normal
0 : Normal
1 : Cool
1 : Cool
2:Warm
2:Warm
Ack
[k] [ ] [Set ID] [ ] [OK] [Data] [x]
Data
Min : 0 ~ Max : 64
29
RS-232C
External control device setup
13. Red ADC gain Adjustment (Color R)
(Command2:w)
16. Low Power (Command2:q)
➜ Adjust the Red gain of ADC part.(RGB)
➜ To reduce the power consumption of the projector.
Transmission
Transmission
[ j ] [w] [ ] [Set ID] [ ] [Data] [Cr]
Data
Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’.
[ j ] [q] [ ] [Set ID] [ ] [Data] [Cr]
Data
0 : Low Power Off
1 : Low Power On
Ack
[q] [ ] [Set ID] [ ] [OK] [Data] [x]
Ack
Data
[w] [ ] [Set ID] [ ] [OK] [Data] [x]
Data Min : 0 ~ Max : 64
0 : Low Power Off
1 : Low Power On
14. Green ADC gain Adjustment (Color G)
(Command2:y)
17. Auto Configure (Command2:u)
➜ Adjust the Green gain of ADC part.(RGB)
➜ To adjust picture position and minimize image shaking
automatically. It works only in RGB mode.
Transmission
[ j ] [y] [ ] [Set ID] [ ] [Data] [Cr]
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’.
Transmission
[ j ] [u] [ ] [Set ID] [ ] [Data] [Cr]
Data
1 : To set
Ack
[u] [ ] [Set ID] [ ] [OK] [Data] [x]
Ack
Data
1 : To set
[y] [ ] [Set ID] [ ] [OK] [Data] [x]
Data Min : 0 ~ Max : 64
15. Blue ADC gain Adjustment (Color B)
(Command2:z)
➜ Adjust the Blue gain of ADC part.(RGB)
Transmission
[ j ] [z] [ ] [Set ID] [ ] [Data] [Cr]
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’.
18. Input Select (Command2:b)
➜ To select input source for the Set.
Transmission
[x] [b] [ ] [Set ID] [ ] [Data] [Cr]
Data
20 : Video
30 : S-Video
50 : RGB-DTV 60 : RGB-PC
80 : DVI-PC
40 : Component
70 : DVI-DTV
Ack
[b] [ ] [Set ID] [ ] [OK] [Data] [x]
Data
Ack
[z] [ ] [Set ID] [ ] [OK] [Data] [x]
Data Min : 0 ~ Max : 64
30
20 : Video
60 : RGB-PC
30 : S-Video
80 : DVI-PC
40 : Component
* The transmission data for RGB-DTV(Data:50) input select is
changed to RGB-PC(Data:60) for the identical mode processing.
In like manner, the data of transmission for DVI-DTV(Data:70)
input select is changed to DVI-PC(Data:80). Therefore,if you
send command to select RGB-DTV or DVI-DTV source, you will
recieve changed data in the Ack message.
ENGLISH
Information
Supported Monitor Display
* The following table lists the display formats supported by the projector.
Sources
Format
VGAEGA
640X350
640X350
640X400
640X400
720X400
720X400
640X480
640X480
640X480
640X480
800X600
800X600
800X600
800X600
800X600
1024X768
1024X768
1024X768
1024X768
1152X864
1152X864
1152X864
1280X960
1280X1024
PC98 / VGA text
VGA
SVGA
XGA
SXGA
Vertical Freq.(Hz)
Horizontal Freq. (kHz)
70.090Hz
85.080Hz
70.090Hz
85.080Hz
70.082Hz
85.039Hz
59.940Hz
72.800Hz
75.00Hz
85.008Hz
56.250Hz
60.317Hz
72.188Hz
75.00Hz
85.061Hz
60.004Hz
70.069Hz
75.029Hz
84.99Hz
60.053Hz
70.01Hz
75.00Hz
60.00Hz
60.020Hz
31.468kHz
37.861kHz
31.468kHz
37.861kHz
31.469kHz
37.927kHz
31.469kHz
37.861kHz
37.500kHz
43.269kHz
35.156kHz
37.879kHz
48.077kHz
46.875kHz
53.674kHz
48.363kHz
56.476kHz
60.023kHz
68.677kHz
54.348kHz
63.995kHz
67.500kHz
60.00kHz
63.981kHz
* If the projector does not support the input signal, “Out of Range” message appears on the screen.
* The projector supports DDC1/2B type as Plug & Play function. (Auto recognition of PC monitor)
* The Synchronization input form for horizontal and vertical frequencies are Separate, Composite and SOG.
* According to PC, the optimum vertical frequency may not be displayed up to the optimum frequency of set in
‘Registration information (Display registration information)’. (ex, The optimum vertical frequency may be displayed
up to 75Hz or under in the resolution of 640X480 or 800X600.)
<DVD/DTV Input>
Signal
NTSC(60Hz)
PAL(50Hz)
Component-*1 RGB(DTV)-*2
480i
O
X
480p
O
O
720p
O
O
1080i
O
O
576i
O
X
576p
O
O
1080i
O
O
* Cable type
1- RCA to D-Sub Adaptor
2- Computer Cable
31
Information
Maintenance
* The projector needs little maintenance. You should keep the lens clean because any dirt or stains may appear
on the screen. If any parts need to be replaced, contact your dealer. When cleaning any part of the projector,
always turn the power off and unplug the projector first.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface of it. Wipe the lens surface gently with an air spray or a soft,
dry lint-free cloth.
To remove dirt or stains on the lens, moisten a soft cloth with water and a neutral detergent and wipe the lens surface gently.
Cleaning the Projector Case
To clean the projector case, first unplug the power cable. To remove dirt or dust, wipe the casing with a soft, dry, lint-free cloth. To remove
stubborn dirt or stains, moisten a soft cloth with water and a neutral detergent and then wipe the casing.
Do not use alcohol, benzene, thinners or other chemical detergents as these can cause the casing to be warped or discolored.
32
Information
Memo
33
Information
Memo
34
Information
Specifications
MODEL
BX220-JD
resolution
1024(Horizontal) x 768(Vertical)pixel
horizontal / vertical ratio
4:3(horizontal:vertical)
DLP panel size
0.55 inches
screen size
1.01~5.08m(40~200 inches)
remote control distance
12m
zoom ratio
1:1.2
Video compatibility
NTSC/PAL/SECAM/NTSC4.43/PAL-M/PAL-N
Power
AC 100 - 240V~50/60Hz, 3A-1A, 260W
height(mm/inches)
100.7/3.9
breadth(mm/inches)
330/12.9
length(mm/inches)
220.1/8.7
Operating Condition
Projector Lamp
temperature
lamp model
In operation : 32~104°F(0°C~40°C)
In storage and transit : -4~140°F(-20°C~60°C)
AJ-LT91
humidity
lamp power consumption
In operation : 0~ 80% relative humidity by dry hygrometer
Not in operation : 0 ~ 90% relative humidity by dry hygrometer
200W
LAMP Replacement
WARNING : Lamp is no user replaceable part.
Do not touch and open the lamp replace cover of
bottom enclosure. It could cause injury and electric
shock due to high temperature and voltage.
Only service personnel can replace lamp after
minimum 3 min. from disconnect mains plug to
avoid injury cause by high temperature of lamp.
* Applicable Lamp: Manufactured by USHIO Inc.,
type NSH200LG
35
Model number
Serial number
:
:
LG DLP PROJECTOR
Please read this manual carefully before operating
your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the bottom of the set and
quote this information to your dealer when you
require service.
BX220-JD
OWNER’S MANUAL