DV288H-NT.HA1ULLS_ENG_5713
DVD PLAYER
OWNER’S MANUAL
MODEL : DN788
Before connecting, operating or adjusting this product,
please read this instruction booklet carefully and completely.
For service/
support Call:
Toll Free Number
1-800-243-0000
© Copyright 2007, LG Electronics U.S.A., Inc.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This lightning flash with arrowhead symbol within
an equilateral triangle is intended to alert the user
to the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature
accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a confined space
such as a bookcase or similar unit.
CAUTION: Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
Slots and openings in the cabinet are provided for ventilation
and to ensure reliable operation of the product and to protect
it from over heating.
The openings should be never be blocked by placing the
product on a bed, sofa, rug or other similar surface. This
product should not be placed in a built-in installation such as
a bookcase or rack unless proper ventilation is provided or
the manufacturer's instruction have been adhered to.
CAUTION: The apparatus should not be exposed to water
(dripping or splashing) and no objects filled with liquids, such
as vases, should be placed on the apparatus.
FCC WARNING: This equipment may generate or use
radio frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the
modifications are expressly approved in the instruction
manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is
made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
FCC COMPLIANCE: The responsible party for this
product’s compliance is:
Marketed and Distributed by LG Electronics U.S.A., Inc.,
1000 Sylvan Avenue, Englewood Cliffs, NJ.
Phone: 1-201-816-2000.
CAUTION concerning the Power Cord
Most devices are recommended be placed on a
dedicated circuit;
That is, a single outlet circuit which powers only that
electronic device and has no additional outlets or branch
circuits. Check the specification page of this owner's manual
to be certain.
CAUTION:
This product employs a Laser System.
To ensure proper use of this product, please read this
owner’s manual carefully and retain it for future reference.
Should the unit require maintenance, contact an authorized
service center.
Use of controls, adjustments or the performance of
procedures other than those specified herein may result in
hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open
the enclosure. Visible laser radiation when open. DO NOT
STARE INTO BEAM.
2
Do not overload wall outlets. Overloaded wall outlets, loose
or damaged wall outlets, extension cords, frayed power
cords, or damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric shock or fire.
Periodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it,
discontinue use of the appliance, and have the cord replaced
with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse,
such as being twisted, kinked, pinched, closed in a door, or
walked upon. Pay particular attention to plugs, wall outlets,
and the point where the cord exits the appliance.
To disconnect power from the mains, pull out the mains cord
plug. When installing the product, ensure that the plug is
easily accessible.
IMPORTANT SAFETY INSTRUCTIONS
PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANUAL. AND
THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
This product has been designed and manufactured to assure personal safety. Improper use can result in electric shock or
fire hazard. The safeguards incorporated in this product will protect you if you observe the following procedures for
installation, use, and servicing.
This product does not contain any parts that can be repaired by the user.
CAUTION:
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read these instructions. - All these safety and
operating instructions should be read before the product
is operated.
2. Keep these instructions. - The safety, operating and
use instructions should be retained for future reference.
3. Heed all warnings. - All warnings on the product and in
the operating instructions should be adhered to.
4. Follow all instructions. - All operating and use
instructions should be followed.
5. Do not use this apparatus near water. – For example:
near a bath tub, wash bowl, kitchen sink, laundry tub, in
a wet basement; or near a swimming pool; and other
areas located near water.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
6. Clean only with dry cloth. – Unplug this product from
the wall outlet before cleaning. Do not use liquid
cleaners.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions. - Slots
and openings in the cabinet are provided for ventilation
and to ensure reliable operation of the product and to
protect it from over-heating. The openings should never
be blocked by placing the product on a bed, sofa, rug or
other similar surface. This product should not be placed
in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The
wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the
obsolete outlet.
3
Contents
Operations . . . . . . . . . . . . . . . .16-20
Introduction . . . . . . . . . . . . . . . . . .5-8
About the
Symbol Display . . . . . .
Symbol used in this Manual . . . . . . .
Notes on Discs . . . . . . . . . . . . . . . . .
Handling Discs . . . . . . . . . . . . . . . .
Storing Discs . . . . . . . . . . . . . . . . .
Cleaning Discs . . . . . . . . . . . . . . . .
Types of Playable Discs . . . . . . . . . .
Regional Code . . . . . . . . . . . . . . . . . .
Front Panel . . . . . . . . . . . . . . . . . . . .
Remote Control . . . . . . . . . . . . . . . . .
Remote Control Operation . . . . . . .
Remote Control Battery Installation
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.5
.5
.5
.5
.5
.5
.6
.6
.7
.8
.8
.8
Installation and Setup . . . . . . . . .9-15
Setting up the Player . . . . . . . . . . . . . . . . . . . .9
DVD Player Connections . . . . . . . . . . . . . . . . .9
Video and Audio Connections to Your TV . . .9
Resolution setting . . . . . . . . . . . . . . . . . . . . .9
HDMI connection . . . . . . . . . . . . . . . . . . . .10
Audio Connection to Optional Equipment . .11
Displaying Disc Information On-Screen . . . .12
Initial Settings . . . . . . . . . . . . . . . . . . . . . . . .12
General Operation . . . . . . . . . . . . . . . . . . .12
LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . .13
• Menu Language . . . . . . . . . . . . . . . . . . .13
• Disc Audio / Subtitle / Menu . . . . . . . . . .13
DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . .13
• TV Aspect . . . . . . . . . . . . . . . . . . . . . . . .13
• Display Mode . . . . . . . . . . . . . . . . . . . . .13
AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
• Dolby Digital / DTS / MPEG . . . . . . . . . .14
• Sample Freq. (Frequency) . . . . . . . . . . .14
• DRC (Dynamic Range Control) . . . . . . . .14
• Vocal . . . . . . . . . . . . . . . . . . . . . . . . . . .14
LOCK (Parental Control) . . . . . . . . . . . . . .14
• Rating . . . . . . . . . . . . . . . . . . . . . . . . . . .14
• Password . . . . . . . . . . . . . . . . . . . . . . . .14
• Area Code . . . . . . . . . . . . . . . . . . . . . . .15
OTHERS . . . . . . . . . . . . . . . . . . . . . . . . . .15
• B.L.E. (Black Level Expansion) . . . . . . . .15
4
General Features . . . . . . . . . . . . . . . . . .
Additional Features . . . . . . . . . . . . . . . .
Playing an Audio CD or MP3/WMA file .
Programmed Playback . . . . . . . . . . . . .
Repeat Programmed Tracks . . . . . . . .
Erasing a Track from Program List . . .
Erasing the Complete Program List . .
Viewing a JPEG file . . . . . . . . . . . . . . . .
Slide Show . . . . . . . . . . . . . . . . . . . . .
Still Picture . . . . . . . . . . . . . . . . . . . . .
Moving to another File . . . . . . . . . . . .
Zoom . . . . . . . . . . . . . . . . . . . . . . . . .
Rotating the picture . . . . . . . . . . . . . .
Listening to MP3 music while watching
picture . . . . . . . . . . . . . . . . . . . . . . . .
Playing a DVD VR Format Disc . . . . . . .
Playing an USB . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.16
.17
.18
.18
.18
.18
.18
.19
.19
.19
.19
.19
.19
. . . .19
. . . .20
. . . .20
Reference . . . . . . . . . . . . . . . . . .21-23
Controlling other TV’s with the remote control . .21
Maintenance and Service . . . . . . . . . . . . . . . .21
Language Codes . . . . . . . . . . . . . . . . . . . . . . .22
Area Codes . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . .23
Specifications . . . . . . . . . . . . . . . . . . . . . . . . .23
Introduction
Notes on Discs
Introduction
To ensure proper use of this product, please read this
owner’s manual carefully and retain it for future
reference.
Handling Discs
This manual provides information on the operation
and maintenance of your DVD player. Should the unit
require service, contact an authorized service location.
Symbol Display
“
” may appear on your TV display during
operation and indicates that the function explained in
this owner’s manual is not available on that specific
DVD video disc.
Symbol Used in this Manual
Storing Discs
Installation and Setup
About the
Do not touch the playback side of the disc. Hold the
disc by the edges so that fingerprints do not get on
the surface. Never stick paper or tape on the disc.
After playing, store the disc in its case. Do not expose
the disc to direct sunlight or sources of heat and never
leave it in a parked car exposed to direct sunlight.
Indicates special notes and operating features.
Cleaning Discs
Tip:
Fingerprints and dust on the disc can cause poor
picture quality and sound distortion. Before playing,
clean the disc with a clean cloth. Wipe the disc from
the center out.
A section whose title has one of the following symbols is
applicable only to the disc represented by the symbol.
ALL
All discs and file listed below
DVD
DVD and finalized DVD±R/RW
ACD
Audio CDs
MP3
MP3 files
WMA
WMA files
Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners, or anti-static
spray intended for older vinyl records.
Reference
Indicates tips and hints for making the task easier.
Operation
Note:
5
Types of Playable Discs
DVD
(8 cm / 12 cm disc)
Audio CD
(8 cm / 12 cm disc)
In addition, this unit plays DVD±R/RW and CD-R/RW,
Dual disc, USB that contains audio titles, MP3, WMA,
and/or JPEG files.
This indicates a product feature that is
capable of playing DVD-RW discs
recorded with Video Recording format.
Regional Code
This unit has a regional code printed on the rear of the
unit. This unit can play only DVD discs labelled as the
same as the rear of the unit or “ALL”.
Notes on Regional Codes
• Most DVD discs have a globe with one or more
numbers in it clearly visible on the cover. This
number must match your unit’s regional code or the
disc cannot play.
• If you try to play a DVD with a different regional
code from your player, the message “Check
Regional Code” appears on the TV screen.
Notes on Copyrights:
Notes:
• Depending on the conditions of the recording
equipment or the CD-R/RW (or DVD±R/RW) disc
itself, some CD-R/RW (or DVD±R/RW) discs
may not be played on the unit.
• Do not use irregularly shaped CDs (e.g., heartshaped or octagonal) since they may result in
malfunctions.
• This DVD player requires discs and recordings to
meet certain technical standards in order to achieve
optimal playback quality. Pre-recorded DVDs are
automatically set to these standards. There are
many different types of recordable disc formats
(including CD-R containing MP3 or WMA files) and
these require certain pre-existing conditions (see
above) to ensure compatible playback.
Customers should note that permission is
required in order to download MP3 / WMA files
and music from the Internet. Our company has
no right to grant such permission. Permission
should always be sought from the copyright
owner.
6
It is forbidden by law to copy, broadcast, show,
broadcast via cable, play in public, or rent copyrighted
material without permission. This product features the
copy protection function developed by Macrovision.
Copy protection signals are recorded on some discs.
When recording and playing the pictures of these discs
picture noise will appear. This product incorporates
copyright protection technology that is protected by
method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision
Corporation and other rights owners.
The Use of this copyright protection technology must be
authorized by Macrovision Corporation, and is intended
for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY
CAUSE ARTIFACTS TO BE DISPLAYED IN THE
PICTURE. IN CASE OF 525 PROGRESSIVE SCAN
PICTURE PROBLEMS, IT IS RECOMMENDED THAT
THE USER SWITCH THE CONNECTION TO THE
‘STANDARD DEFINITION’ OUTPUT. IF THERE ARE
QUESTIONS REGARDING OUR TV SET
COMPATIBILITY WITH THIS MODEL 525p DVD
PLAYER, PLEASE CONTACT OUR CUSTOMER
SERVICE CENTER.
a
Introduction
Front Panel
b
f
a POWER
Switches the unit ON or OFF.
c Disc Tray
Insert a disc here.
b • N (PLAY)
Starts playback.
d Remote Sensor
Point the remote control here.
g
• x (STOP)
Stops playback.
e Display window
Shows the current status of the unit.
• . (SKIP)
Returns to the beginning of current chapter or
track or go to the previous chapter or track.
f USB
Insert a USB.
• > (SKIP)
Go to the next chapter or track.
g Z (OPEN / CLOSE)
Opens or closes the disc tray.
Installation and Setup
e
Operation
d
Reference
c
7
Remote Control
POWER ( )
Switches DVD Player ON and OFF.
OPEN/CLOSE (Z)
Opens and closes the disc tray.
0-9 numerical buttons
Selects numbered items in a menu.
CLEAR
Removes a track number on the
Program List or a mark on the
Marker Search menu.
TV Control Buttons
POWER: Turns the TV on or off.
AV: Selects the TV’s source.
PR/CH +/–: Selects TV’s channel.
VOL +/–: Adjusts TV’s volume.
DVD MENU
Accesses menu on a DVD disc.
SCAN (m / M)
Search backward or forward.
SKIP (. / >)
Go to next chapter or track.
Returns to the beginning of current
chapter or track or go to the
previous chapter or track.
PAUSE/STEP ( X )
Pauses playback temporarily/ press
repeatedly for frame-by-frame
playback.
PLAY (N)
Starts playback.
STOP (x)
Stops playback.
TITLE
Displays title menu, if available.
b / B / v / V (left/right/up/down)
Selects an item in the menu.
ENTER (
)
Confirms menu selection.
DISPLAY
Accesses On-Screen Display.
RETURN (O)
Hide the help menu while watching
a JPEG file.
AUDIO (
)
Selects an audio language or an
audio channel.
SUBTITLE (
)
Selects a subtitle language.
ANGLE (
)
Selects a DVD camera angle,
if available.
MARKER
Marks any point during playback.
SEARCH
Displays MARKER SEARCH menu.
PROGRAM
Enter the program edit mode.
ZOOM
Enlarges video image.
REPEAT
Repeat chapter, track, title, all.
A-B
Repeat sequence from point A to
point B.
RANDOM
Plays tracks in random order.
RESOLUTION
You can change the resolution
depending on your TV.
SETUP
Accesses or removes the Setup
menu.
Remote Control Operation
Point the Remote Control at the remote sensor and
press the buttons.
Caution:
Do not mix old and new batteries and never mix
different types of batteries such as standard, alkaline,
etc.
8
Remote Control Battery installation
Detach the battery cover on the rear of the
Remote Control, and insert two batteries
(size AAA) with 3 and # aligned correctly.
Installation and Setup
Depending on your TV and other equipment there are
various ways you can connect the player. Please refer to
the manuals of your TV, stereo system or other devices
as necessary for additional connection information.
1. Before you set the resolution, this unit must be in
stop mode. Press STOP to stop playback.
2. Press RESOLUTION once. The current resolution
setting will be appears in the display window.
3. Press RESOLUTION repeatedly to change the
resolution you want.
The available resolution according to the connections
are as shown below.
OUTPUT CONNECTION
HDMI
VIDEO OUT
COMPONENT
VIDEO OUT
Video and Audio Connections
to Your TV
Make sure the DVD player is connected directly to the
TV and not to a VCR, otherwise the DVD image could
be distorted by the copy protection system.
S-Video – Connect the S-VIDEO OUT jack on the
DVD Player to the S-Video in jack on the TV using
the S-Video cable (S).
Video – Connect the VIDEO OUT jack on the
DVD player to the video in jack on the TV using
the video cable (V).
Audio – Connect the left and right AUDIO OUT
jacks of the DVD Player to the audio left and right
IN jacks on the TV using the audio cables (A).
Do not connect the DVD Player’s AUDIO OUT jack
to the phone in jack (record deck) of your audio
system.
Introduction
Resolution setting
Installation and Setup
DVD Player Connections
Available Resolution
1920 x 1080i
1280 x 720p
720 x 480p
720 x 480i
1920 x 1080i
1280 x 720p
720 x 480p
720 x 480i
VIDEO OUT
720 x 480i
720 x 480p
S-VIDEO
720 x 480i
Operation
The picture and sound of a nearby TV, VCR, or radio
may be distorted during playback. If this occurs,
position the player away from the TV, VCR, or radio,
or turn off the unit after removing the disc.
Progressive Scan
• If your television is a high-definition or “digital
ready” television, you may take advantage of
the DVD player’s progressive scan output for
the highest possible video resolution.
• Progressive scan does not work with the analog
video connections (yellow VIDEO OUT jack).
• The 720p and 480p resolutions are the
progressive scan applied resolution.
Notes:
• For Video and S-VIDEO connections, resolution
must be set to 480i or 480p by pressing
RESOLUTION button, however Video OUT is
always at 480i standard resolution.
• If your TV does not accept your resolution setting,
abnormal picture appears on the screen.
Please read TV’s owner’s manual then set the
resolution that your TV can accept.
• For 720p and 1080i resolution on the component
video out, only non-copy protected discs can be
played back.If the disc is copy protected, it will be
displayed at the 480p resolution without HDMI
cable connection. With HDMI cable connection, the
picture may not be displayed properly.
Reference
Setting up the Player
Component Video – Connect the COMPONENT /
PROGRESSIVE SCAN jacks on the DVD Player
to the corresponding jacks on the TV using an Y
PB PR cable (C).
9
HDMI connection
If you have an HDMI TV or a monitor, you can
connect it to this player using an HDMI cable.
1. Set the TV’s source to HDMI (refer to TV Owner’s
manual).
2. Connect the HDMI OUT jack on the unit to the
HDMI jack on a HDMI compatible TV or
monitor (H).
3. Press RESOLUTION repeatedly to select the
desired resolution.
Notes:
• Both PCM and Bitstream Audio out is available
when the sample frequency is set to 48kHz in HDMI
connection.
• If Audio setup is set to bitstream and your TV does
not support Bitstream Audio out in HDMI
connection, audio sound may not be outputted or
distorted.
• When the no sound or noisy sound are outputted
with HDMI connection, set the Audio option [Dolby
Digital, DTS or MPEG] in SETUP menu to PCM or
Off.
• The arrow on the cable connector body should face
up for correct alignment with the connector on the
player.
• If there is noise or lines on the screen, please
check the HDMI cable.
• Not all HDCP-compatible DVI devices will work with
this unit.
• If your HDMI TV does not support HDCP,
the blue screen appears on the screen.
• If the abnormal picture appears on the TV screen,
turn off the unit and then turn the unit on again.
Tips:
• When you use HDMI connection, you can change
the resolution (480i, 480p, 720p, 1080i) for the
HDMI output.
• The HDMI will be outputted at 480p resolution, even
if you set the resolution to 480i on the HDMI
connection.
10
About HDMI
HDMI (High Definition Multimedia Interface) supports
both video and audio on a single digital connection for
use with DVD Players, Set-Top Boxes, and other AV
devices.
HDMI was developed to provide the technologies of
HDCP (High-bandwidth Digital Content Protection).
HDCP is used to protect digital content transmitted
and received.
HDMI has the capability to support standard,
enhanced or high-definition video plus standard to
multi-channel surround-sound audio, HDMI features
include uncompressed digital video, a bandwidth of up
to 5 gigabytes per second, one connector (instead of
several cables and connectors), and communication
between the AV source and AV devices such as
DTVs.
HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI licensing LLC.
Connect the DVD player to your optional equipment
for audio output.
Amplifier equipped with 2-channel analog stereo
or Dolby Pro Logic ll / Pro Logic: Connect the left
and right AUDIO OUT jacks on the DVD player to the
audio left and right IN jacks on your amplifier,
receiver, or stereo system, using the audio cables (A).
Introduction
Audio Connection to Optional
Equipment
Amplifier equipped with 2-channel digital stereo
(PCM) or audio / video receiver equipped with a
multi-channel decoder (Dolby Digital™, MPEG 2,
or DTS):
Connect one of the DVD Player’s DIGITAL AUDIO
OUT jacks (OPTICAL O or COAXIAL X) to the
corresponding jack on your amplifier. Use an optional
digital (OPTICAL O or COAXIAL X) audio cable.
Installation and Setup
Digital Multi-channel sound
A digital multi-channel connection provides the best
sound quality. For this you need a multi-channel audio
/ video receiver that supports one or more of the
audio formats supported by your DVD player such as
MPEG 2, Dolby Digital and DTS. Check the receiver
manual and the logos on the front of the receiver.
Notes:
• If the audio format of the digital output does not match
the capabilities of your receiver, the receiver produces
a strong, distorted sound or no sound at all.
Operation
Manufactured under license from Dolby
Laboratories. “Dolby”, “Pro Logic” and
the double-D symbol are trademarks of
Dolby Laboratories.
• Six Channel Digital Surround Sound via a digital
connection can only be obtained if your receiver is
equipped with a Digital Multi-channel decoder.
Reference
DTS and DTS Digital Out are trademarks
of Digital Theater Systems, Inc.
11
Displaying Disc Information
On-Screen
You can display various information about the disc
loaded on-screen.
1. Press DISPLAY to show various playback
information.
The displayed items differ depending on the disc
type or playing status.
Initial Settings
By using the Setup menu, you can make various
adjustments to items such as picture and sound.
You can also set a language for the subtitles and the
Setup menu, among other things. For details on each
Setup menu item, see pages 13 to 15.
To display and exit the Menu:
Press SETUP to display the menu. A second press of
SETUP will take you back to initial screen.
To go to the next level:
Press B on the remote control.
To go back to the previous level:
Press b on the remote control.
General Operation
1. Press SETUP.
The Setup menu appears.
2. You can select an item by pressing v / V and
change or select the setting by pressing b / B.
• Title – Current title. number/total number of
titles.
• Chapter – Current chapter number/total number
of chapters.
• Time – Elapsed playing time.
• Audio – Selected audio language or channel.
• Subtitle – Selected subtitle.
• Angle – Selected angle/total number of angles.
Note:
If any button is not pressed for a few seconds, the onscreen display disappears.
2. Use v / V to select the desired option then press
B to move to the second level. The screen shows
the current setting for the selected item, as well as
alternate setting(s).
3. Use v / V to select the second desired option and
then press B to move to the third level.
4. Use v / V to select the desired setting then press
ENTER to confirm your selection.
Some items require additional steps.
5. Press SETUP or PLAY (N) to exit the Setup
menu.
12
DISPLAY
Menu Language
TV Aspect
Introduction
LANGUAGE
Disc Audio / Subtitle / Menu
Select the language you prefer for the audio track
(disc audio), subtitles, and the disc menu.
Original – Refers to the original language in which
the disc was recorded.
Other – To select another language, press
numeric buttons and then ENTER to enter the
corresponding 4-digit number according to the
language code list on the page 22. If you enter the
wrong language code, press CLEAR.
4:3 – Select when a standard 4:3 TV is connected.
Installation and Setup
Select a language for the Setup menu and on-screen
display.
16:9 – Select when a 16:9 wide TV is connected.
Display Mode
The Display Mode setting works only when the TV
Aspect mode is set to 4:3.
Letterbox – Displays a wide picture with bands on
the upper and lower portions of the screen.
Panscan – Automatically displays the wide picture
on the entire screen and cuts off the portions that
do not fit.
Reference
Operation
Off (for Disc Subtitle) – Turn off Subtitle.
13
AUDIO
LOCK (Parental Control)
Each DVD disc has a variety of audio output options.
Set the player’s AUDIO options according to the type
of audio system you use.
Rating
Blocks playback of rated DVDs based on their
content. Not all discs are rated.
Dolby Digital / DTS / MPEG
Bitstream – Select “Bitstream” if you connect this
unit’s DIGITAL OUT jack to an amplifier or other
equipment with a Dolby Digital, DTS or MPEG
decoder.
PCM (for Dolby Digital / MPEG) – Select when
connected to a two-channel digital stereo amplifier.
DVDs encoded in Dolby Digital, MPEG will be
automatically downmixed to two-channel PCM
audio.
Off (for DTS) – If you select “Off”, the DTS signal
is not output through the DIGITAL OUT jack.
Sample Freq. (Frequency)
If your receiver or amplifier is NOT capable of handling
96 kHz signals, select 48 kHz. When this choice is
made, this unit automatically converts any 96 kHz
signals to 48 kHz so your system can decode them.
2. To access the LOCK options, you must input the
password you have created. If you have not yet
entered password, you are prompted to do so.
Input a password and press ENTER. Enter it again
and press ENTER to verify. If you make a mistake
before pressing ENTER, press CLEAR.
3. Select a rating from 1 to 8 using the v / V buttons.
Rating 1-8 – Rating one (1) has the most
restrictions and rating eight (8) is the least
restrictive.
Unlock – If you select unlock, parental control is
not active and the disc plays in full.
4. Press ENTER to confirm your rating selection,
then press SETUP to exit the menu.
If your receiver or amplifier is capable of handling 96
kHz signals, select 96 kHz.
Password
Check the documentation for your amplifier to verify
its capabilities.
1. Select Password on the LOCK menu and then
press B.
DRC (Dynamic Range Control)
2. Follow the step 2 as shown above (Rating).
With the DVD format, you can hear a program’s
soundtrack in the most accurate and realistic
presentation. However, you may wish to compress the
dynamic range of the audio output (the difference
between the loudest sounds and the quietest ones).
This allows you to listen to a movie at a lower volume
without losing clarity of sound.
Set DRC to On for this effect.
Vocal
Set to On only when a multi-channel karaoke DVD is
playing. The karaoke channels on the disc mix into
normal stereo sound.
14
1. Select “Rating” on the LOCK menu then
press B.
You can enter or change password.
To change the password, press ENTER when the
“Change” option is highlighted. Enter a new
password using the numbered buttons then press
ENTER. Enter it again and press ENTER to verify.
3. Press SETUP to exit the menu.
If you forget your password
If you forget your password, you can clear it using the
following steps:
1. Press SETUP to display the Setup menu.
2. Input the 6-digit number “210499” and press
ENTER. The password is cleared.
Area Code
Introduction
Enter the code of the area whose standards were
used to rate the DVD video disc, based on the list on
page 22.
1. Select “Area Code” on the LOCK menu then
press B.
2. Follow the step 2 as shown previous page
(Rating).
3. Select the first character using v / V buttons.
Installation and Setup
4. Press B and select the second character using
v / V buttons.
5. Press ENTER to confirm your Area code selection.
OTHERS
Operation
B.L.E. (Black Level Expansion)
To select the black level of playback pictures.
Set your preference and monitor’s ability.
On: Expanded grey scale. (0 IRE cut off)
Reference
Off: Standard grey scale. (7.5 IRE cut off)
15
Operations
General Features
Buttons
Operations
Discs
OPEN/CLOSE (Z)
Opens or closes the disc tray.
ALL
PAUSE/STEP (X)
During playback, press PAUSE/STEP (X) to pause
playback.
ALL
Press PAUSE/STEP (X) repeatedly to play Frame-byFrame.
During playback, press SKIP (. or >) to go to the
next chapter/track or to return to the beginning of the
current chapter/track.
DVD
SKIP (. / >)
ALL
Press SKIP (.) twice briefly to step back to the
previous chapter/track.
SCAN (m / M)
During playback, press SCAN (m or M) repeatedly to
select the required scan speed.
DVD disc; 4 steps
MP3, Audio CD ; 3 steps
DVD
While the playback is paused, press SCAN (M)
repeatedly to play in slow motion (4 steps, forward only).
DVD
REPEAT
During playback, press REPEAT repeatedly to select a
desired repeat mode.
DVD Video discs: Chapter/Title/Off
Audio CD, MP3/WMA discs: Track/All/Off
ALL
A-B
Press the A-B button one at a time to select a point A and
point B and repeats a sequence from point A (Starting
point) to point B (End point).
ZOOM
During playback or pause mode, press ZOOM to enlarge
the video image (3 steps).
You can move through the zoomed picture using
b / B / v / V buttons. Press CLEAR to exit.
DVD
RANDOM
During playback or in stop mode, press RANDOM for
random playback.
ACD
TITLE
If the current DVD title has a menu, the title menu
appears on the screen. Otherwise, the disc menu may
appears.
DVD
DVD MENU
The disc menu appears on the screen.
DVD
ANGLE (
)
SUBTITLE (
AUDIO (
16
During playback of DVD disc that contains scenes
recorded at different camera angles, press ANGLE (
repeatedly to select a desired angle.
)
)
During playback, press SUBTITLE (
select a desired subtitle language.
DVD
DVD
)
) repeatedly to
During playback, press AUDIO (
) repeatedly to hear
a different audio language or audio track.
DVD
DVD
ACD
MP3
ACD
MP3
WMA
Notes on general features:
Last Scene Memory
• If you press SKIP (>) once during Repeat Chapter
(Track) playback, the repeat playback cancels.
This player memorizes last scene from the last disc
that is viewed. The last scene remains in memory
even if you remove the disc from the player or switch
off the player. If you load a disc that has the scene
memorized, the scene is automatically recalled.
• Zoom may not work on some DVDs.
• When you are playing a DVD disc that contains
scenes recorded at different camera angles, the
angle indicator will blink on the TV screen during the
operations as an indication that angle switching is
possible
• The A-B repeat function is available only in the
current track of the Audio CD.
DVD
ACD
Note:
This player does not memorize the scene of a disc if
you switch off the player before commencing to play
the disc.
Screen Saver
Additional Features
Time Search
DVD
To start playing at any chosen time on the disc:
The screen saver appears when you leave the DVD
player in Stop mode for about five minutes. If the
Screen Saver is displayed for five minutes, the DVD
Player automatically turns itself off.
1. Press DISPLAY during playback.
2. Press v / V to select the time clock icon and
“--:--:--” appears.
3. Input the required start time in hours, minutes, and
seconds from left to right. If you enter the wrong
numbers, press CLEAR to remove the numbers
you entered. Then input the correct numbers.
4. Press ENTER to confirm.
Playback starts from the selected time.
Marker Search
DVD
Operation
To enter a Marker
You can start playback from up to nine memorized
points. To enter a marker, press MARKER at the
desired point on the disc. The Marker icon appears on
the TV screen briefly. Repeat to enter up to nine
markers.
To Recall or Clear a Marked Scene
1. During disc playback, press SEARCH. The marker
search menu appears on the screen.
2. Within 9 seconds, press b / B to select a marker
number that you want to recall or clear.
3. Press ENTER and playback starts from the marked
scene. Or, Press CLEAR and the marker number is
erased from the list.
4. You can play any marker by inputting its number on
the marker search menu.
17
Playing an Audio CD or
MP3/WMA file
This unit can play Audio CDs or MP3/WMA files.
MP3/ WMA/ Audio CD
Once you insert an MP3/WMA files recorded media or
Audio CD, a menu appears on the TV screen.
Press v / V to select a track/file and then press
PLAY (N) or ENTER and playback starts.
You can use variable playback functions.
Refer to page 16-17.
Programmed Playback
The program function enables you to store your
favorite tracks from any disc in the player memory.
A program can contain 30 tracks.
1. Insert an Audio CD or MP3/WMA files recorded
media. AUDIO CD or MUSIC menu appears.
2. Press PROGRAM and the
E
mark will appear
Note:
Press PROGRAM again to exit the program edit
mode, then the E mark will disappear.
3. Select a track on the “List” and then press ENTER
to place the selected track on the “Program” list.
Repeat to place additional tracks on the list.
4. Use b / B / v / V to select the track you want to
start playing on the “Program” list.
ID3 TAG
5. Press PLAY (N) or ENTER to start.
Playback begins in the order in which you
programmed the tracks. Playback stops after all of
the tracks on the “Program” list have played once.
When playing a file containing information such as
track titles, you can see the information by pressing
DISPLAY. [ Song, Artist, Album, Comment, Genre ]
6. To resume normal playback from programmed
playback, select a track on the list and then press
PLAY (N).
Tips:
• Press DVD MENU to move to the next page.
Repeat Programmed Tracks
• On a DISC with MP3/WMA and JPEG file, you can
switch MUSIC and PHOTO menu. Press TITLE, and
MUSIC or PHOTO word on top of the menu is
highlighted.
• Track: Repeats the current track.
MP3 / WMA disc compatibility with this player is
limited as follows:
• Sampling frequency: within 8 - 48 kHz (MP3),
within 32 - 48kHz (WMA)
• Bit rate: within 8 - 320kbps (MP3),
32 - 384 kbps (WMA)
• The player cannot read an MP3/WMA file that has
a file extension as non than “.mp3” / “.wma”.
• CD-R physical format should be ISO 9660
• If you record MP3 / WMA files using software that
cannot create a file system (eg. Direct-CD) it is
impossible to playback MP3 / WMA files.
We recommend that you use Easy-CD Creator,
which creates an ISO 9660 file system.
• File names should have a maximum of 8 letters
and must incorporate an .mp3 or .wma extension.
• They should not contain special letters such as / ?
* : “ < > l etc.
• The total number of files in a folder should be less
than 1012 files.
18
Press REPEAT to select a desired repeat mode.
• All: Repeats all the tracks on programmed list.
• Off(No display): Does not play repeatedly.
Note:
If you press SKIP (>) once during Repeat Track
playback, the repeat playback cancels.
Erasing a Track from Program List
1. During stop mode, press PROGRAM and the
mark will appear
E
2. Use b / B / v / V to select the track that you wish
to erase from the Program list.
3. Press CLEAR. Repeat step 1-3 to erase additional
tracks on the list.
Erasing the Complete Program List
1. During stop mode, press PROGRAM and the
mark will appear
E
2. Use b / B / v / V to select “Clear All” and then
press ENTER.
Note:
The programs are also cleared when the power is
off or the disc is removed.
Zoom
Viewing a JPEG file
This unit can play JPEG files.
1. Insert a JPEG files recording media.
The PHOTO menu appears on the TV screen.
During watching pictures, press ZOOM to enlarge the
video image (3 steps).
You can move through the zoomed picture using
b / B / v / V buttons.
Note:
When the resolution is set to 720p or 1080i,
this function is not available.
Rotating the picture
Press v / V during showing a picture to rotate the
picture clockwise or counter clockwise.
3. If you want to view a particular file, press
v / V to highlight a file and press ENTER or
PLAY (N).
Listening to MP3 music while watching
picture
1. Insert the disc containing the two types of file in
the player.
4. To return to the PHOTO menu while watching
pictures, press STOP (x).
2. Press TITLE to display the PHOTO menu.
Tips:
• If you are in a file list and want to return to the
previous Folder list, use v / V buttons to highlight
and press ENTER.
4. Use B to select
icon then press ENTER.
Playback starts. The playback will continue until
stop is pressed.
• Press DVD MENU to move to the next page.
• There are three Slide Speed options
: >>>
(Fast), >> (Normal) and > (Slow).
Use b / B / v / V to highlight
. Then, use b / B
to select the option you want to use and then press
ENTER.
• On a DISC with MP3/WMA and JPEG file, you can
switch MUSIC and PHOTO menu. Press TITLE, and
MUSIC or PHOTO word on top of the menu is
highlighted.
• While watching a picture, press RETURN (O) to
hide the help menu.
• When viewing a JPEG file, the help menu will not
be displayed on the TV screen if the resolution is
set to 720p or 1080i.
Slide Show
Use b / B / v / V to highlight the
then press ENTER.
(Slide Show)
3. Press v / V to select a photo file.
Note:
When the resolution is set to 720p or 1080i,
this function is not available.
Tip:
To listen to only the desired music while watching
picture, program the desired tracks from the “MUSIC”
menu and then proceed as above.
JPEG disc compatibility with this player is
limited as follows:
• Depending upon the size and the number of
JPEG files, it could take a long time for the DVD
player to read the disc’s contents. If you do not
see an on-screen display after several minutes,
some of the files may be too large — reduce the
resolution of the JPEG files to less than 5 million
pixels and burn another disc.
• The total number of files in a folder should be less
than 1012 files.
Still Picture
• Some discs may be incompatible due to a
different recording format or the condition of disc.
1. Press PAUSE/STEP (X) during slide show.
The player will now go into PAUSE mode.
• Ensure that all the selected files have the “.jpg”
extensions when copying into the CD layout.
2. To return to the slide show, press PLAY (N) or
press PAUSE/STEP (X) again.
• If the files have “.jpe” or “.jpeg” extensions, please
rename them as “.jpg” file.
Moving to another File
• File names without “.jpg” extension will not be
able to be read by this unit. Even though the files
are shown as JPEG image files in Windows
Explorer.
Press SKIP (. or >) or cursor (b or B)
once during viewing a picture to advance to the next
or previous file.
Operation
2. Press v / V to select a folder, and press
ENTER. A list of files in the folder appears.
19
Playing a DVD VR Format Disc
Playing from USB device
This unit will play DVD-R/RW disc that is recorded
using the DVD-Video format that have been finalized
using a DVD-recorder.
1. Connect the USB device to the USB port on the
front panel after power is on.
This unit will play DVD-RW disc that is recorded
using the Video Recording (VR) format.
1. Insert a disc and close the tray, It start playing
automatically.
2. The DVD-VR menu appears on the TV screen
when you press DVD MENU buttons while playing.
2. Press RETURN(O) on the remote control.
The USB choice menu appears on the TV screen.
3. Press ENTER.
The menu appears.
4. Press RETURN(O) to exit the menu.
To Remove the USB device from the unit
1. Press RETURN(O) to exit the menu.
2. Remove the USB from device the unit.
For details on each operation item,
refer a relevant page. (See the page 18-20)
3. Press v / V to select a track then press
PLAY (N) or ENTER and playback starts.
4. Press DVD MENU to move to the list menu.
Notes:
• Unfinalized DVD-R/RW discs cannot be played in
this player.
• Some DVD-VR disc are made with CPRM data by
DVD RECORDER. Player does not support these
kinds of discs.
What is CPRM?
CPRM is a copy protection system (with scramble
system) only allowing the recording of ‘copy once’
broadcast programs. CPRM stands for Content
Protection for Recordable Media.
20
Notes:
• Do not extract the USB device during operation.
• Music files (MP3/WMA), image files (JPEG) can be
played.
• This unit can not use USB HUB.
• A device is not supported when the total number of
files is more than 1,000.
• The USB function of this unit does not support all
kinds of USB devices.
• This unit supports only USB Flash Memory.
• This unit can support USB1.1.
Reference
Controlling other TV’s with the
remote control
Maintenance and Service
Refer to the information in this chapter before
contacting a service technician.
You can control the sound level, input source, and
power switch of your LG TV with the supplied remote
control.
Handling the Unit
You can control the sound level, input source, and
power switch of non-LG TVs as well. If your TV is
listed in the table below, set the appropriate
manufacturer code.
Please save the original shipping carton and packing
materials. If you need to ship the unit, for maximum
protection, re-pack the unit as it was originally packed
at the factory.
1. While holding down TV POWER button, press the
number buttons to select the manufacturer code
for your TV (see the table below).
2. Release TV POWER button.
Code numbers of controllable TVs
If more than one code number is listed, try entering
them one at a time until you find the one that works
with your TV.
Manufacturer
Code Number
LG / GoldStar
1 (Default), 2
Zenith
1, 3, 4
Samsung
6, 7
Sony
8, 9
Hitachi
4
Notes:
• Depending on your TV, some or all buttons may not
function on the TV, even after entering the correct
manufacturer code.
• If you enter a new code number, the code number
previously entered will be erased.
• When you replace the batteries of the remote, the
When shipping the unit
Keeping the exterior surfaces clean
• Do not use volatile liquids such as insecticide spray
near the unit.
• Do not leave rubber or plastic products in contact
with the unit for a long period of time. since they
leave marks on the surface.
Cleaning the unit
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution.
Do not use strong solvents such as alcohol, benzine,
or thinner, as these might damage the surface of the
unit.
Maintaining the Unit
The unit is a high-tech, precision device. If the optical
pick-up lens and disc drive parts are dirty or worn,
the picture quality could be diminished.
Depending on the operating environment, regular
inspection and maintenance are recommended after
every 1,000 hours of use.
For details, please contact your nearest authorized
service center.
Reference
code number you have set may be reset to the
default setting. Set the appropriate code number
again.
21
Language Codes
Use this list to input your desired language for the following initial settings:
Disc Audio, Disc Subtitle, Disc Menu.
Language
Abkhazian
Afar
Afrikaans
Albanian
Ameharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali; Bangla
Bhutani
Bihari
Breton
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
Chinese
Corsican
Croatian
Czech
Danish
Dutch
English
Esperanto
Estonian
Faroese
Code
6566
6565
6570
8381
6577
6582
7289
6583
6588
6590
6665
6985
6678
6890
6672
6682
6671
7789
6669
7577
6765
9072
6779
7282
6783
6865
7876
6978
6979
6984
7079
Language
Fiji
Finnish
French
Frisian
Galician
Georgian
German
Greek
Greenlandic
Guarani
Gujarati
Hausa
Hebrew
Hindi
Hungarian
Icelandic
Indonesian
Interlingua
Irish
Italian
Japanese
Javanese
Kannada
Kashmiri
Kazakh
Kirghiz
Korean
Kurdish
Laothian
Latin
Latvian, Lettish
Code
7074
7073
7082
7089
7176
7565
6869
6976
7576
7178
7185
7265
7387
7273
7285
7383
7378
7365
7165
7384
7465
7487
7578
7583
7575
7589
7579
7585
7679
7665
7686
Language
Lingala
Lithuanian
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian
Oriya
Panjabi
Pashto, Pushto
Persian
Polish
Portuguese
Quechua
Rhaeto-Romance
Rumanian
Russian
Samoan
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Shona
Sindhi
Code
7678
7684
7775
7771
7783
7776
7784
7773
7782
7779
7778
7865
7869
7879
7982
8065
8083
7065
8076
8084
8185
8277
8279
8285
8377
8365
7168
8382
8372
8378
8368
Language
Singhalese
Slovak
Slovenian
Somali
Spanish
Sudanese
Swahili
Swedish
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Turkish
Turkmen
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
Code
8373
8375
8376
8379
6983
8385
8387
8386
8476
8471
8465
8484
8469
8472
6679
8473
8479
8482
8475
8487
8575
8582
8590
8673
8679
6789
8779
8872
7473
8979
9085
Area Codes
Choose an area code from this list.
Area
Afghanistan
Argentina
Australia
Austria
Belgium
Bhutan
Bolivia
Brazil
Cambodia
Canada
Chile
China
Colombia
Congo
Costa Rica
Croatia
Czech Republic
Denmark
Ecuador
Egypt
El Salvador
22
Code
AF
AR
AU
AT
BE
BT
BO
BR
KH
CA
CL
CN
CO
CG
CR
HR
CZ
DK
EC
EG
SV
Area
Code
Ethiopia
ET
Fiji
FJ
Finland
FI
France
FR
Germany
DE
Great Britain
GB
Greece
GR
Greenland
GL
Herd and Mcdonald Islands HM
Hong Kong
HK
Hungary
HU
India
IN
Indonesia
ID
Israel
IL
Italy
IT
Jamaica
JM
Japan
JP
Kenya
KE
Kuwait
KW
Libya
LY
Luxembourg
LU
Area
Malaysia
Maldives
Mexico
Monaco
Mongolia
Morocco
Nepal
Netherlands
Netherlands Antilles
New Zealand
Nigeria
Norway
Oman
Pakistan
Panama
Paraguay
Philippines
Poland
Portugal
Romania
Russian Federation
Code
MY
MV
MX
MC
MN
MA
NP
NL
AN
NZ
NG
NO
OM
PK
PA
PY
PH
PL
PT
RO
RU
Area
Saudi Arabia
Senegal
Singapore
Slovak Republic
Slovenia
South Africa
South Korea
Spain
Sri Lanka
Sweden
Switzerland
Taiwan
Thailand
Turkey
Uganda
Ukraine
United States
Uruguay
Uzbekistan
Vietnam
Zimbabwe
Code
SA
SN
SG
SK
SI
ZA
KR
ES
LK
SE
CH
TW
TH
TR
UG
UA
US
UY
UZ
VN
ZW
Troubleshooting
Symptom
Possible Cause
Correction
No power.
• The power cord is disconnected.
• Plug the power cord into the wall outlet
securely.
The power is on, but
the DVD player does
not work.
• No disc is inserted.
• Insert a disc. (Check the disc indicator
in the display window is lit.)
No picture.
• The TV is not set to receive DVD
signal output.
• Select the appropriate video input
mode on the TV.
• The video cable is not connected
securely.
• Connect the video cable securely.
• The equipment connected with the
audio cable is not set to receive DVD
signal output.
• Select the correct input mode of the
audio receiver so you can listen to the
sound from the DVD player.
• The power of the equipment connected
with the audio cable is turned off.
• Turn on the equipment connected with
the audio cable.
• The AUDIO options are set to the
wrong position.
• Set the AUDIO option to the correct
position, then turn on the DVD player
again by pressing POWER.
• An unplayable disc is inserted.
• Insert a playable disc. (Check the disc
type and regional code.)
• The rating level is set.
• Change the rating level.
• The remote control is not pointed at
the remote sensor on the DVD player.
• Point the remote control at the remote
sensor of the DVD player.
• The remote control is too far from the
DVD player.
• Operate the remote control closer to
the DVD player.
No sound.
The DVD player does
not start playback.
The remote control
does not work properly.
Specifications
Power requirements: AC 120 V, 60 Hz
Power consumption: 8 W
Dimensions (Approx.):
430 x 35 x 202 mm (17 x 1.4 x 7.9 inches)
(W x H x D) without foot
Weight (Approx.): 1.6 kg (3.5 lbs)
Operating temperature:
5 °C to 35 °C (41 °F to 95 °F)
Operating humidity: 5 % to 90 %
Outputs
VIDEO OUT:
1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
S-VIDEO OUT:
(Y) 1.0 V (p-p), 75 Ω, negative sync, Mini DIN 4-pin x 1
(C) 0.3 V (p-p) 75 Ω
COMPONENT VIDEO OUT:
(Y) 1.0 V (p-p), 75 Ω,negative sync, RCA jack x 1
(Pb)/(Pr) 0.7 V (p-p), 75 Ω, RCA jack x 2
AUDIO OUT:
2.0 Vrms (1 KHz, 0 dB), 600 Ω, RCA jack (L, R) x 1
DIGITAL OUT (COAXIAL):
0.5 V (p-p), 75 Ω, RCA jack x 1
DIGITAL OUT (OPTICAL):
3 V (p-p), Optical jack x 1
System
Laser:
Semiconductor laser, wavelength 650 nm
Signal system: NTSC
Frequency response:
DVD (PCM 96 kHz): 8 Hz to 44 kHz
DVD (PCM 48 kHz): 8 Hz to 22 kHz
CD: 8 Hz to 20 kHz
Signal-to-noise ratio:
More than 90 dB (ANALOG OUT connectors only)
Harmonic distortion: Less than 0.02%
Dynamic range:
More than 95 dB (DVD/CD)
Accessories:
Video cable (1), Audio cable (1), Remote control (1),
Batteries (2)
Reference
General
Note: Design and specifications are subject to change without prior notice.
23
LG Electronics, Inc.
Limited Warranty - USA
This LG Electronics product, will be repaired or replaced, at LG’s option, if it proves to be defective in material or
workmanship, under normal use, during the warranty period (“Warranty Period”) listed below, effective from the date
(“Date of Purchase”) of original consumer purchase of the product. This warranty is good only to the original purchaser
of the product and effective only when used in the United States, excluding U.S. Territories.
WARRANTY PERIOD:
HOW SERVICE IS HANDLED:
LABOR: 90 days from the Date of Purchase.
Call 1-800-243-0000 for instructions on getting the
defective unit repaired or replaced.
PARTS: One Year from the Date of Purchase.
Please retain dated sales receipt and your box to
return the unit to LG for repair or replacement.
* Parts replaced are warranted for the remaining portion
of the original warranty period.
Shipping both ways will be paid by LG during the first
90 days of the Warranty Period. During the remainder
of the Warranty Period (91~365 days), you pay inbound
shipping charges and LG pays return shipping charges.
Visit our website at: http://www.lgservice.com
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT ANY IMPLIED
WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE EXPRESS WARRANTY PERIOD ABOVE. LG
ELECTRONICS WILL NOT BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL OR PUNITIVE
DAMAGES OF ANY NATURE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, INCLUDING WITHOUT
LIMITATION, LOST REVENUES OR PROFITS, LOST OR CORRUPTED PROGRAMMING OR DATA, OR ANY OTHER DAMAGE
WHETHER BASED IN CONTRACT, TORT OR OTHERWISE. Some states do not allow the exclusion or limitation of incidental or
consequential damages or limitation on how long an implied warranty lasts, so the above exclusion or limitation may not apply to
you. This warranty gives you specific legal rights and you may also have other rights that may vary from state to state.
THIS LIMITED WARRANTY DOES NOT APPLY TO:
•
Damages or operating problems that result from shipping, installation, adjustment of user controls,
calibration, maintenance or failure to maintain, or separate system components; and
•
Damages or operating problems that result from normal wear and tear, misuse, abuse, operation outside
environmental specifications or contrary to the requirements or precautions in the Operating Guide, accident,
lightning strikes or other natural causes, unauthorized modification or alteration, incorrect electrical current
or voltage, signal reception or input, software not licensed directly by LG, software errors that do not disable
functionality, operating and software protocols adopted after the date of manufacture or for outside the US,
institutional or commercial use, or other causes not arising out of defect in material or workmanship.
The cost of repair or replacement under these excluded circumstances shall be borne by the consumer.
CUSTOMER INTER-ACTIVE CENTER NUMBERS:
For Warranty Service, Where to buy, Product
Assistance, or Customer Assistance
Call 1-800-243-0000 (24 hours a day, 365 days per year)
and select appropriate options from the menu.
Or visit our website at http://www.lgservice.com
LG ELECTRONICS U.S.A., INC.
1000 SYLVAN AVENUE
ENGLEWOOD CLIFFS, NJ
P/N : MFL36465713
Printed in China
Issue O