DVD PLAYER
OWNER’S MANUAL
MODEL : DVD-3350E
Before connecting, operating or adjusting this product,
please read this instruction booklet carefully and completely.
FOR THE GUARANTEE TERMS & CONDITIONS,
PLEASE REFER TO BACK COVER OF THIS MANUAL.
PAGE 2
INTRODUCTION
Safety Precautions
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
CAUTION:
THIS DVD PLAYER EMPLOYS A LASER SYSTEM.
TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS OWNER’S MANUAL
CAREFULLY AND RETAIN FOR FUTURE REFERENCE, SHOULD THE UNIT REQUIRE
MAINTENANCE, CONTACT AN AUTHORIZED SERVICE LOCATION-SEE SERVICE
PROCEDURE.
USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE
ENCLOSURE. VISIBLE LASER RADIATION WHEN OPEN THE ENCLOSURE. DO NOT
STARE INTO BEAM.
WARNING:
CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY
RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
POWER: This DVD player operates on a mains supply of 100-240V~, 50/60Hz.
WIRING: This DVD player is supplied with a BSI 1363 approved 13 amp mains plug, fused at 13 or 5 amp. When
replacing the fuse always use a 13 or 5 amp BS 1362, BSI or ASTA approved type. Never use this plug with the fuse
cover omitted. To obtain a replacement fuse cover contact your dealer or “LG Electronics U.K.Ltd.” If the type of plug
supplied is not suitable for the mains sockets in your home, then the plug should be removed and a suitable type
fitted. Please refer to the wiring instructions below:
WARNING: A mains plug removed from the mains lead of this DVD player must be destroyed. A mains plug with
bared wires is hazardous if inserted in a mains socket.
Do not connect either wire to the earth pin, marked with the letter E or with the earth symbol
or coloured green
or green and yellow.
If any other plug is fitted, use a 13 or 5 amp fuse, either in the plug, or at the distribution board.
IMPORTANT: The wires in this mains lead are coloured in accordance with the following codes:
- BLUE: NEUTRAL, BROWN: LIVE - As the colours of the wires in the mains lead of this DVD player may not
correspond with the coloured marking indentifying the terminals in your plug, proceed as follows: The wire which is
coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which
is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
This product is manufactured to comply
with the radio interference requirements
of EEC DIRECTIVE 89/336/EEC,
93/68/EEC and 73/23/EEC.
RECORD YOUR MODEL NUMBER (Now, while you can see it)
The model and serial number of your new DVD
player are located on the back of the DVD player cabinet. For your future convenience, we suggest that you record these numbers here:
MODEL NO.____________________________________
SERIAL NO.____________________________________
INTRODUCTION
PAGE 3
Table of Contents
Introduction
Advanced Operation
❏
Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . 2
❏
Using a title menu . . . . . . . . . . . . . . . . . . . . . . . 22
❏
Table of Contents. . . . . . . . . . . . . . . . . . . . . . . . . 3
❏
Using a DVD menu . . . . . . . . . . . . . . . . . . . . . . 22
❏
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
❏
Memorizing Settings for Viewed DVDs . . . . . . . . 23
❏
Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . . 5
❏
Changing subtitle language . . . . . . . . . . . . . . . . 24
❏
Identification of Controls . . . . . . . . . . . . . . . . . . 6-9
❏
Changing audio soundtrack language. . . . . . . . . 24
Front Panel/Display window. . . . . . . . . . . . . . . . . . . . . 6
❏
Viewing from another angle . . . . . . . . . . . . . . . . 25
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
❏
Producing a 3D Surround effect . . . . . . . . . . . . . 25
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
❏
Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Preparing the Remote Control . . . . . . . . . . . . . . . . . . . 9
❏
Storing markers in memory to be
viewed (listened to) again. . . . . . . . . . . . . . . . . . 27
Operating with the Remote Control . . . . . . . . . . . . . . . 9
❏
Zoom Feature . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Connections
❏
Random Play . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
❏
Connecting to a TV . . . . . . . . . . . . . . . . . . . . . . 10
❏
Program Play . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
❏
Connecting to an Audio System . . . . . . . . . . . . . 11
❏
Playback with MP3 . . . . . . . . . . . . . . . . . . . . 30-31
❏
Connecting to Optional Audio System . . . . . . 12-15
Enjoying Dolby Digital Sound. . . . . . . . . . . . . . . . . . . 12
Initial Settings
Enjoying Dolby Digital (5.1CH) Sound . . . . . . . . . . . . 13
❏
Common procedures of initial settings . . . . . . . . 32
Enjoying Dolby Pro Logic Surround Sound . . . . . . . . 14
❏
Selecting disc Languages . . . . . . . . . . . . . . . . . 33
Enjoying 2 Channel Digital Stereo Sound. . . . . . . . . . 15
❏
Selecting rating level and password . . . . . . . 34-35
Enjoying DTS Sound . . . . . . . . . . . . . . . . . . . . . . . . . 15
❏
Selecting TV Aspect . . . . . . . . . . . . . . . . . . . . . . 36
❏
Selecting Menu Language . . . . . . . . . . . . . . . . . 37
Basic Operations
❏
Selecting TV Output . . . . . . . . . . . . . . . . . . . . . . 37
❏
Basic Playback . . . . . . . . . . . . . . . . . . . . . . . 16-18
❏
Selecting Pseudo PAL . . . . . . . . . . . . . . . . . . . . 38
❏
Various speed playback with Shuttle Ring . . . . . . 19
❏
Selecting Digital Audio Output . . . . . . . . . . . . . . 39
❏
Setting the Speaker Setup . . . . . . . . . . . . . . . . . 40
❏
Table of Languages and Their Abbreviations . . . 41
Operation Using GUI Menu Icons
❏
General Information about GUI menu icons . . . . 20
❏
Detailed description of each GUI menu icon . . . . 21
Reference
❏
Disc Requirements/Copyright Information . . . . . . 42
❏
Before Calling Service Personnel . . . . . . . . . . . . 43
❏
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . 44
PAGE 4
INTRODUCTION
Precautions
Notes on handling
❏
❏
❏
❏
❏
When shipping the DVD player, always use the
original shipping carton and packing materials.
For maximum protection, repack the unit as it was
originally packed at the factory.
Do not use volatile liquids, such as insect spray, near
the DVD player. Do not leave rubber or plastic
products in contact with the DVD player for a long
time. They will leave marks on the finish.
The top and rear panels of the DVD player may
become warm after a long period of use. This is
normal and not a malfunction.
When the DVD player is not in use, be sure to
remove the disc and turn off the power.
If you do not use the DVD player for a long period, the
unit may not function properly in the future. Turn on
and use the DVD player occasionally.
Notes on Locating
❏
Notes on Moisture Condensation
Moisture condensation damages the DVD player.
Please read the following carefully.
Moisture condensation occurs, for example, when
you pour a cold drink into a glass on a warm day.
Drops of water form on the outside of the glass. In
the same way, moisture may condense on the optical pick-up lens inside this unit, one of the most crucial internal parts of the DVD player.
Exa
Notes on Cleaning
Use a soft, dry cloth for cleaning.
❏ For stubborn dirt, soak the cloth in a weak detergent
solution, wring well and wipe. Use a dry cloth to wipe
it dry. Do not use any type of solvent, such as thinner
and benzine, as they may damage the surface of the
DVD player.
❏ If you use a chemical saturated cloth to clean the
unit, follow that product’s instructions.
Warning: Cleaning and adjustment of lenses
and/or other components of playback mechanism
should be performed by a qualified service
technician.
To Obtain a Clear Picture
The DVD player is a high technology, precision device. If
the optical pick-up lens and disc drive parts are dirty or
worn down, the picture quality becomes poor. To obtain
a clear picture, we recommend regular inspection and
maintenance (cleaning or parts replacement) every
1,000 hours of use depending on the operating
environment. For details, contact your nearest dealer.
Optical
p lens
pick-u
Moisture condensation occurs during the following
cases.
❏
❏
When you place this DVD player near a TV, radio, or
VCR, the playback picture may become poor and the
sound may be distorted. In this case, move the DVD
player away from the TV, radio, or VCR.
mples of moistur
e
ensation
cond
❏
❏
When you bring the DVD player directly from a cold
place to a warm place.
When you use the DVD player in a room where you
just turned on the heater, or a place where the cold
wind from the air conditioner directly hits the unit.
In summer, when you use the DVD player in a hot
and humid place just after you move the unit from
an air conditioned room.
When you use the DVD player in a humid place.
It’ s to o
wa rm !
❏
Do not use the DVD player when moisture condensation may occur.
If you use the DVD player in such a situation, it may
damage discs and internal parts. Remove the disc,
connect the power cord of the DVD player to the wall
outlet, turn on the DVD player and leave it “ON” for
two or three hours. After two or three hours, the
DVD player will have warmed up and evaporated
any moisture. Keep the DVD player connected to
the wall outlet and moisture condensation will seldom occur.
Wa
it!
INTRODUCTION
PAGE 5
Notes on Discs
This section shows you how to handle, clean, and store discs.
On Handling Discs
❍
Do not touch the playback side of the disc.
On Storing Discs
❍
❍
❍
❍
Do not attach paper or tape to discs.
On Cleaning Discs
❍
❍
❍
Do not store discs in a place subject to
direct sunlight or near heat sources.
Do not store discs in places subject to
moisture and dust such as a bathroom or
near a humidifier.
Store discs vertically in a case. Stacking or
placing objects on discs outside of their
case may cause warping.
Fingerprints and dust on the disc cause
picture and sound deterioration. Wipe the
disc from the centre outward with a soft
cloth. Always keep the disc clean.
If you cannot wipe off the dust with a soft
cloth, wipe the disc lightly with a slightly
moistened soft cloth and finish with a dry
cloth.
Do not use any type of solvents such as
thinner, benzine, commercially available
cleaners or anti-static spray for vinyl LPs.
They may damage the disc.
About This Owner’s Manual
❍
❍
❍
This owner’s manual explains the basic
instructions of this DVD player.
Some DVD video discs have functions that
may not be explained in this owner’s manual.
Therefore, some instructions may differ from
this owner’s manual, and there may be extra
instructions. In this case, follow the instructions
displayed on the TV screen or package.
“
” may appear on the TV screen
during operation. This icon means the
function explained in this owner’s manual is
not available on that specific DVD video
disc.
PAGE 6
INTRODUCTION
Identification of Controls
Front Panel
SELECT/ENTER button
Disc tray
POWER indicator
(Power ON mode: Green color,
Standby mode: Red color)
SHUTTLE
Ring
STOP button
PAUSE/STEP button
PLAY button
SLOW/SCAN
PAUSE/STEP STOP
POWER
D
RE
FW
V
PLAY
OPEN/
CLOSE
STANDBY
SKIP
MENU
SELECT/
ENTER
ARROW
buttons
Display window
POWER button
Remote sensor
MENU button
OPEN/CLOSE button
SKIP buttons
Display Window
PROGRAM indicator
Operating status indicator
RANDOM indicator
CD indicator
Repeat playback
mode indicators
DVD indicator
MP3
CD DVD
MP3 indicator
Angle icon indicator
TITLE
CHP/TRK
PROG.
RANDOM ALL A
B
Total playing time/elapsed time indicators
Chapter/Track number indicator
Title number indicator
INTRODUCTION
PAGE 7
Identification of Controls
Rear Panel
5.1CH AUDIO OUT jacks
COAXIAL DIGITAL AUDIO OUT jack
AUDIO OUT (L/R) jacks
TV SYSTEM SELECT Switch
Refer to explanation below.
EXTERNAL INPUT (SCART) jack
DIGITAL
OUT
5.1CH AUDIO OUT
FRONT
REAR
AUDIO
OUT
L
EXTERNAL
INPUT
L
COAXIAL
R
DIGITAL
OUT
R
TO TV
S-VIDEO
OUT
OPTICAL
OPTICAL DIGITAL AUDIO OUT jack
Remove the dust protection cap from
the connector and connect the optical
digital cable (not supplied) firmly so
that the configurations of both the
cable and the connector match. Keep
the dust protection cap and always
reattach the cap when not using the
connector to protect against dust.
CENTER
WOOFER
VIDEO
OUT
AUTO
PAL
NTSC
VIDEO OUT jack
S-VIDEO OUT jack
TO TV (SCART) jack
POWER CORD
Connect to an AC 100-240V,
50/60Hz outlet only.
Dust protection cap
TV System Select
You can enjoy NTSC or PAL discs by using your TV SYSTEM SELECT switch to choose the appropriate system.
• If you try to play back PAL disc with NTSC-TV. The player will not playback the disc.
• When the selected TV SYSTEM SELECT switch does not coincide with the system of your TV, normal color
picture may not be displayed.
• Select the TV SYSTEM SELECT switch when the power is turned off.
• When you playback NTSC disc with PAL-TV, some discs may produce black bands at the top and
bottom of the screen.
Position of TV SYSTEM SELECT switch
Connected TV
Available disc
PAL
PAL
NTSC/PAL DVD disc
NTSC
NTSC
NTSC DVD disc
AUTO
MULTI system TV
NTSC/PAL DVD disc
PAGE 8
INTRODUCTION
Identification of Controls (con’d)
REMOTE CONTROL
You will find instructions for each of the remote control functions in the appropriate sections of this
instruction manual.
POWER button
PLAY button
POWER
STOP button
REV SKIP button
FWD SKIP button
PAUSE/STEP button
PLAY
OPEN/CLOSE button
SELECT/ENTER button
SKIP
SKIP
** ARROW buttons
STOP
SETUP button
PAUSE
/STEP
GUI DISPLAY button
SELECT
/ENTER
OPEN/CLOSE
SETUP
GUI DISPLAY
RETURN button
3D SOUND button
NUMBER buttons
RETURN
CLEAR button
1
2
PROGRAM button
3
3D SOUND
ANGLE button
4
6
*MENU button
PROGRAM
7
SUBTITLE button
5
8
9
CLEAR
TITLE
MENU
0
AUDIO button
AUDIO SUBTITLE ANGLE
MARKER-SEARCH
***TITLE button
REPEAT
A-B
RANDOM
ZOOM
MARKER-SEARCH buttons
REPEAT button
ZOOM button
SLOW/SCAN
A-B button
RANDOM button
FWD/REV SLOW/SCAN
Shuttle Ring
REV
FWD
*MENU button
Use the MENU button to display the
menu screen included on DVD video
discs. To operate a menu screen,
follow the instructions in “Using a
DVD Menu” (page 22).
** Directional arrow buttons
(up, down, left, right) for use in highlighting a selection on a GUI menu
screen, TITLE and MENU screen.
***TITLE button
Use the TITLE button to display the
title screen included on DVD video
discs. To operate a menu screen,
follow the instructions in “Using a Title
Menu” (page 22).
INTRODUCTION
PAGE 9
Identification of Controls (con’d)
Preparing the Remote Control
Insert the batteries into the remote control so you can
use it to operate the DVD player.
1
Operating with the Remote Control
This section shows you how to use the remote control.
Point the remote control at the
remote sensor and press the
buttons.
Open the battery cover.
SLOW/SCAN
PAUSE/STEP STOP
RE
Insert batteries (AAA size).
3
OPEN/
CLOSE
STANDBY
SKIP
● Make sure to match the + and - on the batteries to
the marks inside the battery compartment.
D
2
FW
V
PLAY
POWER
MENU
SELECT/
ENTER
30° 30°
Within about 23 ft (about 7 m)
Close the cover.
POWER
PLAY
SKIP
SKIP
STOP
PAUSE
/STEP
SELECT
/ENTER
AAA
AAA
OPEN/CLOSE
Distance: About 23 ft (7 m) from the front of the remote
sensor
Angle:
About 30° in each direction of the front of the
remote sensor
* Do not expose the remote sensor of the DVD
player to a strong light source such as direct
sunlight or illumination. If you do so, you may not
be able to operate the DVD player with the remote
control.
Notes on batteries
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
Improper use of batteries may cause battery leakage and
corrosion.
To operate the remote control correctly, follow the
instructions.
Do not insert the batteries into the remote control in the
wrong direction.
Do not charge, heat, open, or short-circuit the batteries.
Do not throw the batteries into fire.
Do not leave dead or exhausted batteries in the remote
control.
Do not use different types of batteries together, or mix
old and new batteries.
If you do not use the remote control for a long period of
time, remove the batteries to avoid possible damage
from battery corrosion.
If the remote control does not function correctly or if the
operating range becomes reduced, replace all batteries
with new ones.
If battery leakage occurs, wipe the battery liquid from the
battery compartment, then insert new batteries.
The batteries should last about one year with normal
use.
Notes on the remote control
❍
❍
❍
❍
❍
Direct the remote control at the remote sensor of the
DVD player.
Do not drop or give the remote control a shock.
Do not leave the remote control near an extremely hot or
humid place.
Do not spill water or put anything wet on the remote control.
Do not open the remote control.
PAGE 10
CONNECTIONS
Connecting to a TV
Connect the DVD player to your TV
If the DVD player is connected to the TV through a video cassette recorder, the picture may not be played back
normally with some DVDs. So we strongly recommended you not to connect the DVD player to your video cassette
recorder when setting up your home entertainment system.
• To view pictures from the video cassette recorder, set the player to the standby mode.
To SCART
(EXTERNAL INPUT)
DIGITAL
OUT
5.1CH AUDIO OUT
FRONT
REAR
AV1
AUDIO
OUT
21-pin
SCART
socket
L
EXTERNAL
INPUT
L
COAXIAL
R
DIGITAL
OUT
AV2
Video Cassette
Recorder
R
TO TV
S-VIDEO
OUT
OPTICAL
To SCART (T0 TV)
CENTER
WOOFER
To
S-VIDEO
OUT
VIDEO
OUT
For using SCART’s RGB signal or
S-VIDEO OUT jacks, you must set
“TV Output Select” at the SETUP
menu. (See page 37.)
To AUDIO(L/R)/
VIDEO OUT
Audio/Video cable
(Supplied)
To 21-pin SCART
socket
If the TV has an S-video input,
connect the DVD player with the
S-video cable.
To video input
To audio input
S-video (Supplied)
To S-video input
21-pin SCART Cable
(Not Supplied)
TV or monitor with
audio/video inputs
To 21-pin SCART
terminal of TV set
Notes
❍
❍
❍
❍
Refer to the owner’s manual of your TV as well.
When you connect the DVD player to your TV, be sure to turn off the power and unplug both units from the wall outlet before
making any connections.
Connect the DVD player to your TV directly. If you connect the DVD player to a VCR, the playback picture will be distorted
because DVD video discs are copy protected.
In case of the TV set corresponding to RGB signal, the RGB signal is automatically selected in the TV.(Only when the “TV
Output Select” is select to “Component” on the SETUP menu)
Warning
Do not set the Digital Audio Output of this DVD player to “Dolby Digital” unless you are connecting the DIGITAL OUT jack of this
DVD player to an AV decoder that has the Dolby Digital decoding function. High volume sound may damage your hearing as well
as the speakers. (Refer to “Selecting Digital Audio Output” on page 39.)
CONNECTIONS
PAGE 11
Connecting to an Audio System
You can listen to the sound of audio CDs and DVD video discs in stereo.
DIGITAL
OUT
5.1CH AUDIO OUT
FRONT
REAR
AUDIO
OUT
To S-VIDEO OUT
S-video cable (Supplied)
L
EXTERNAL
INPUT
L
COAXIAL
R
DIGITAL
OUT
R
TO TV
OPTICAL
S-VIDEO
OUT
CENTER
To AUDIO OUT (L/R)
WOOFER
VIDEO
OUT
If the TV has an S-video input, connect the DVD
player with the S-video cable.
To VIDEO OUT
To S-video input
Video cable (Supplied)
To video input (yellow)
TV or monitor with
audio/video inputs
To audio inputs
of the amplifier
Audio cable (Supplied)
Audio system
Notes
❍
❍
❍
❍
❍
Refer to the owner’s manual of your audio system as well.
When you connect the DVD player to other equipment, be sure to turn off the power and unplug all of the equipment from the
wall outlet before making any connections.
If you place the DVD player near a tuner or radio, the radio broadcast sound might be distorted. In this case, move the DVD
player away from the tuner and radio.
The output sound of the DVD player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate
listening level. Otherwise, the speakers may be damaged by a sudden high volume sound.
Turn off the receiver before you connect or disconnect the DVD player’s power cord. If you leave the receiver power on, the
speakers may be damaged.
Warning
Do not set the Digital Audio Output of this DVD player to “Dolby Digital” unless you are connecting the DIGITAL OUT jack of this DVD
player to an AV decoder that has the Dolby Digital decoding function. High volume sound may damage your hearing as well as the
speakers. (Refer to “Selecting Digital Audio Output” on page 39.)
PAGE 12
CONNECTIONS
Connecting to Optional Audio System
Enjoying Dolby Digital Sound
You can enjoy the high quality dynamic sound of Dolby Digital, Dolby Pro Logic, and 2 Channel Digital Stereo.
Dolby Digital
Dolby Digital is the surround sound technology used in theatres showing the latest movies, and is now available to
reproduce this realistic effect in the home. You can enjoy motion picture and live concert DVD video discs with this
dynamic realistic sound by connecting the DVD player to a 6 channel receiver equipped with a Dolby Digital decoder
or Dolby Digital processor.
DIGITAL
OUT
5.1CH AUDIO OUT
FRONT
REAR
AUDIO
OUT
L
EXTERNAL
INPUT
L
COAXIAL
R
DIGITAL
OUT
R
TO TV
S-VIDEO
OUT
OPTICAL
CENTER
WOOFER
VIDEO
OUT
To DIGITAL OUT
(COAXIAL or OPTICAL)
To S-VIDEO OUT
or VIDEO OUT
75 ohm coaxial cable
or Optical cable
Receiver equipped
with a Dolby Digital
(AC-3) decoder
To enjoy Dolby Digital sound
from this DVD player you need
the following:
● DVD recorded in Dolby Digital
S-Video cable
or Video cable
Connection
example
To digital
audio input
To S-video Input
or Video Input
Front speaker
(left)
Front speaker
(right)
Center
speaker
● 6 channel receiver equipped
with a Dolby Digital decoder,
or Dolby Digital processor and
power receiver
Sub woofer
Rear speaker
(left surround)
Rear speaker
(right surround)
● 5 speakers and 1 sub woofer
To enjoy Dolby Digital sound
You need to select “Dolby
Digital” on the SETUP menu.
* Manufactured under license from Dolby Laboratories Licensing
Corporation. “Dolby” and the double-D symbol are trademarks of Dolby
Laboratories Licensing Corporation.
Confidential Unpublished Works. 1992-1997 Dolby Laboratories, Inc. All
rights reserved.
C
Notes
❍
❍
❍
❍
Refer to the owner’s manual of your audio equipment as well.
When you connect the DVD player to other equipment, be sure to turn off the power and unplug all of the equipment from the
wall outlet before making any connections.
The output sound of the DVD player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate
listening level. Otherwise, the speakers may be damaged by a sudden high volume sound.
Turn off the receiver before you connect or disconnect the DVD player’s power cord. If you leave the receiver power on, the
speakers may be damaged.
CONNECTIONS
PAGE 13
Connecting to Optional Audio System
Enjoying Dolby Digital (5.1 CH) Sound
Dolby Digital Surround (5.1 CH)
Dolby Digital is a six-channel digital surround sound technology developed by Dolby Laboratories for theatre-like surround
sound reproduction. DVDs supporting Dolby Digital technology feature the
logo. You can enjoy realistic, theatre-like
surround sound from DVD movie or music disc featuring this logo. Two front, one centre and two rear speakers plus a
subwoofer make up the “5.1-channel” audio system that Dolby Digital uses.
Hookups
Connect a receiver with 5.1 channel inputs to the player and to the speakers. See the figure below.
DIGITAL
OUT
5.1CH AUDIO OUT
FRONT
REAR
AUDIO
OUT
L
EXTERNAL
INPUT
L
COAXIAL
R
DIGITAL
OUT
R
TO TV
S-VIDEO
OUT
OPTICAL
CENTER
WOOFER
VIDEO
OUT
To S-Video Out
or Video Out
Front L
Front R
Center
Woofer
Rear R
Rear L
To 5.1CH input
S-Video cable
or Video cable
AV Receiver
with 5.1CH input
Connection example
To S-video Input
or Video Input
Front speaker
(left)
Front speaker
(right)
Center
speaker
Sub woofer
Rear speaker
(left surround)
Rear speaker
(right surround)
PAGE 14
CONNECTIONS
Connecting to Optional Audio System
Enjoying Dolby Pro Logic Surround Sound
Dolby Pro Logic Surround
You can still enjoy the excitement of Surround Sound even if your A/V receiver does not offer Dolby Digital decoding, if your
A/V receiver has a Dolby Pro Logic decoder. Refer to the following connection diagram.
DIGITAL
OUT
5.1CH AUDIO OUT
FRONT
REAR
AUDIO
OUT
L
EXTERNAL
INPUT
L
COAXIAL
R
DIGITAL
OUT
R
TO TV
OPTICAL
Connect one or two rear speakers.
The output sound from the rear speakers
will be monaural even if you connect two
rear speakers.
S-VIDEO
OUT
CENTER
WOOFER
VIDEO
OUT
To VIDEO OUT
To AUDIO OUT
Audio cable
Video cable
To audio input
Connection example
Receiver equipped
with Dolby Pro
Logic Surround
To video input
Center speaker
Front
speaker
(right)
Front
speaker
(left)
TV
Rear speaker
(left)
●
Rear speaker
(right)
With a receiver equipped with Dolby Digital
Connect the equipment the same way as described in “Enjoying Dolby Digital Sound” on the previous page. Refer to that
receiver’s owner’s manual and set the receiver so you can enjoy Dolby Pro Logic Surround sound.
Warning
Do not set the Digital Audio Output of this DVD player to “Dolby Digital” unless you are connecting the DIGITAL OUT jack of this DVD
player to an AV decoder that has the Dolby Digital decoding function. High volume sound may damage your hearing as well as the
speakers. (Refer to “Selecting Digital Audio Output” on page 39.)
CONNECTIONS
PAGE 15
Connecting to Optional Audio System
Enjoying 2 Channel Digital Stereo Sound
2 Channel Digital Stereo
You can enjoy the dynamic sound of 2 Channel Digital Stereo by connecting this DVD player to a receiver equipped with a
digital audio input and speaker system (right and left front speakers).
Connection example
75 ohm coaxial cable or
optical cable
Receiver equipped with a
digital audio input
To digital audio input
To S-video Input
or Video Input
S-Video cable
or Video cable
To DIGITAL OUT
(COAXIAL or
OPTICAL)
To S-VIDEO OUT
or VIDEO OUT
DIGITAL
OUT
5.1CH AUDIO OUT
FRONT
Front speaker
(left)
Front speaker
(right)
AUDIO
OUT
REAR
TV
L
EXTERNAL
INPUT
L
COAXIAL
R
DIGITAL
OUT
R
TO TV
S-VIDEO
OUT
OPTICAL
CENTER
VIDEO
OUT
WOOFER
Enjoying DTS Sound
Introducing DTS Digital SurroundTM...the finest technology ever invented to transform existing "home theatre" systems into six
discrete channels of exceptionally clear, better-than-compact disc, digital audio performance. And DTS Digital Surround is the
only 5.1 surround sound format that can deliver this revolutionary 3-dimensional experience through new music recordings on
compact discs, original 5.1 soundtracks on motion picture laserdiscs, and soon, a wide variety of products on DVD.
Connection example
Receiver equipped
with a DTS decoder
75 ohm coaxial cable or
Optical Cable
To digital audio input
To S-video Input
or Video Input
To DIGITAL OUT
(COAXIAL or
OPTICAL)
S-Video cable
or Video cable
To S-VIDEO OUT
or VIDEO OUT
DIGITAL
OUT
5.1CH AUDIO OUT
FRONT
REAR
Front
speaker
(left)
Front speaker
(right)
Center
speaker
AUDIO
OUT
L
EXTERNAL
INPUT
Sub woofer
L
COAXIAL
R
DIGITAL
OUT
R
TO TV
OPTICAL
S-VIDEO
OUT
CENTER
WOOFER
Rear speaker
(left surround)
Rear speaker
(right surround)
VIDEO
OUT
“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
Notes
❍
❍
❍
❍
Refer to the owner’s manual of your receiver as well.
When you connect the DVD player to other equipment, be sure to turn off the power and unplug all of the equipment from the
wall outlet before making any connections.
The output sound of the DVD player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening level. Otherwise, the speakers may be damaged by a sudden high volume sound.
Turn off the receiver before you connect or disconnect the DVD player’s power cord. If you leave the receiver power on, the
speakers may be damaged.
PAGE 16
CONNECTIONS
Basic Playback
This section shows you the basics on how to play back a DVD video disc.
SLOW/SCAN
PAUSE/STEP STOP
RE
D
POWER
FW
V
PLAY
OPEN/
CLOSE
STANDBY
SKIP
MENU
SELECT/
ENTER
3
1
4
POWER
Preparations
● When you want to play back DVD video discs, turn on the TV and
select the video input source connected to the DVD player.
● When you want to enjoy the sound of DVD video discs or audio
CDs from the audio system, turn on the audio system and select
the input source connected to the DVD player.
● For connection details, see pages 10 through 15.
● Set the playback picture size according to the aspect ratio of the
connected TV at the SETUP menu (TV Aspect).
● If you do not have the necessary equipment to enjoy Dolby Digital
sound, set the Digital Audio Output at the SETUP menu to “PCM”.
PLAY
SKIP
1
Press POWER.
2
Press OPEN/CLOSE.
SKIP
The DVD player turns on and the power indicator light
is changed to a green color.
STOP
PAUSE
/STEP
SELECT
/ENTER
OPEN/CLOSE
SETUP
2
●
The disc tray opens.
You can open the disc tray by pressing this button even if the
DVD player is in standby mode.
GUI DISPLAY
RETURN
1
2
3
3
3D SOUND
4
5
6
7
8
9
PROGRAM
CLEAR
TITLE
●
There are two different disc sizes. Place the disc in the
correct guide on the disc tray. If the disc is out of the guide, it
may damage the disc and cause the DVD player to malfunction.
Do not place anything except 3” discs or 5” discs on the disc
tray.
MENU
0
AUDIO SUBTITLE ANGLE
REPEAT
A-B
MARKER-SEARCH
RANDOM
●
ZOOM
4
SLOW/SCAN
REV
Place a disc on the disc tray with the
playback side down.
FWD
●
Press PLAY.
The disc tray is automatically closed and playback
begins.
If the disc is placed in upside down (and it is a single sided
disc), “NO DISC” or “DISC ERROR” appears on the TV
screen.
MP3
CD DVD
TITLE
CHP/TRK
PROG.
RANDOM ALL A
B
Operating status indicator
●
●
If you insert an audio CD, the CD indicator lights up in the DVD
display. The title number does not appear.
After playing back all of the chapters in the title, the DVD player
automatically stops and returns to the menu screen.
When a menu screen appears on the TV screen.
In case of interactive DVDs with control, a menu screen appears on
the TV screen. Perform step 5 on page 17 to start play.
Example of interactive
DVD On-Screen Menu
BASIC OPERATION
PAGE 17
Basic Playback
5
Press D/E/F/G and press SELECT/ENTER, or
press the numeric button(s), to select the
desired item.
1
2
POWER
OR
3
4
PLAY
Play of the selected item now begins.
SKIP
SKIP
●
STOP
5
PAUSE
/STEP
SELECT
/ENTER
OPEN/CLOSE
SETUP
GUI DISPLAY
RETURN
1
2
3
4
5
6
7
8
9
5
For further information, also refer to the jacket or case of
the disc you are playing.
After operation
When the unit is not in use, remove the disc and press
POWER to turn off the power.
3D SOUND
PROGRAM
CLEAR
TITLE
❍
AUDIO SUBTITLE ANGLE
REPEAT
A-B
MARKER-SEARCH
RANDOM
ZOOM
❍
❍
SLOW/SCAN
REV
Notes
MENU
0
FWD
❍
❍
❍
Do not move the DVD player during playback. Doing so may
damage the disc and the DVD player.
Use the OPEN/CLOSE button on the remote control or DVD
player to open and close the disc tray. Do not push the disc tray
while it is moving. Doing so may cause the DVD player to
malfunction.
Do not push up the disc tray or put any objects other than discs
on the disc tray. Doing so may cause the DVD video
player to malfunction.
Keep your fingers well clear of the disc tray as it is closing. Be
especially careful with children’s fingers around the
closing disc tray as there is a risk of personal injury.
When “
” appears on the TV screen while a button is
pressed, it means that this function is not available on the disc
you are playing.
Depending on the DVD disc, some operations may be different
or restricted. Refer to the jacket or case of the disc you are
playing.
PAGE 18
BASIC OPERATION
Basic Playback
Stopping Play
Press STOP during playback.
Resume Play
● When play is stopped, the unit records the point where
STOP was pressed (RESUME function).
Press PLAY and play will resume from this point.
POWER
REV SKIP
❍
SKIP
SKIP
FWD SKIP
❍
STOP
PAUSE/
STEP
Notes
PLAY
PLAY
STOP
PAUSE
/STEP
SELECT
/ENTER
OPEN/CLOSE
SETUP
❍
❍
❍
GUI DISPLAY
Resume function will be cleared when the STOP is pressed on
the STOP mode.
Resume function will be cleared when the power is turned off
and then on.
Opening the disc tray cancels Resume function.
The Resume function may not be available on some DVD discs.
If the player is left in the stop mode for more than 8 minutes, the
power shuts off automatically.
RETURN
1
2
3
4
5
6
7
8
9
Still Picture (Pause)
3D SOUND
PROGRAM
CLEAR
TITLE
●
MENU
0
AUDIO SUBTITLE ANGLE
REPEAT
A-B
MARKER-SEARCH
RANDOM
Press PAUSE/STEP during playback.
DVD
The player will be placed in the still picture mode.
● CD
The player will be placed in the pause mode.
ZOOM
Frame advance (DVD only)
Press PAUSE/STEP during still playback.
SLOW/SCAN
REV
FWD
(Each time you press PAUSE/STEP, the picture advances
one frame)
To resume normal playback, press PLAY.
Skipping forward or back
Skipping forward
Press SKIP
during playback.
A chapter (DVD) or a track (CD) is skipped each time the
button is pressed.
Skipping back
Press SKIP
during playback.
● When the button is pressed once midway through a
chapter/track, the player returns to the start of that
chapter/track. When it is pressed again, a chapter/track is
skipped each time the button is pressed.
BASIC OPERATION
PAGE 19
Various speed playback with Shuttle Ring
You can play back discs at various speeds, and
resume normal playback.
To play in slow-motion
During still picture mode, rotating and holding the
SHUTTLE ring to the positions indicated gives
those slow modes.
● The variable-speed slow picture will appear on the TV
screen.
POWER
PLAY
PLAY
SKIP
Release the SHUTTLE ring to resume the still
picture mode.
SKIP
1/16
STOP
PAUSE
/STEP
1/16
1/8
SELECT
/ENTER
1/8
1/4
1/4
OPEN/CLOSE
SETUP
GUI DISPLAY
1/2
1
2
3
4
5
6
7
8
9
1/2
REVERSE
DIRECTION
RETURN
FORWARD
DIRECTION
3D SOUND
PROGRAM
CLEAR
TITLE
MENU
0
AUDIO SUBTITLE ANGLE
REPEAT
A-B
MARKER-SEARCH
RANDOM
SLOW/SCAN
REV
To scan at fast forward or fast reverse.
ZOOM
FWD
During playback mode, rotating and holding the
SHUTTLE ring to the positions indicated gives
those fast search modes.
● The variable-speed search picture will appear on the TV
screen.
SLOW/SCAN
Shuttle ring
Release the SHUTTLE ring to resume normal
playback.
G
FF X2
FF X4
FF X16
FF X100
REVERSE
DIRECTION
GG X2
GG X4
GG X16
GG X100
FORWARD
DIRECTION
Notes
❍
❍
❍
❍
The DVD player does not play back sound during slow-motion
playback, the high speed reverse and forward playback of DVD
video discs.
However, the DVD player plays back sound during fast forward
or fast reverse playback of audio CDs.
Subtitles do not appear on the screen during slow motion and
scan playback.
The DVD player provides four (4) scan speeds for DVD movie
play. Only two (2) scan speeds are available during Audio CD
play.
The DVD player does not play back in slow-motion in case of
audio CD.
PAGE 20
OPERATION USING GUI MENU ICONS
General Information about GUI menu icons
This unit features GUI Menu Icons showing disc
information (title/chapter/track number, elapsed playing
time, audio/subtitle language, angle, and sound) and
player information (repeat play, play mode, marker,
etc.). Some icons only show the indicated information.
Other icons allow the settings to be changed.
Common procedures
1
● Title function can be accessed from the stop mode.
2
3
PLAY
SKIP
SKIP
STOP
SELECT
/ENTER
OPEN/CLOSE
SETUP
1
GUI DISPLAY
RETURN
1
2
3
4
5
6
3D SOUND
PROGRAM
7
Press D/E to select the desired item.
● The current selected item is indicated by a yellow
frame on its GUI menu icons.
POWER
PAUSE
/STEP
Press GUI DISPLAY during playback.
8
9
CLEAR
TITLE
2, 3
Press F/G to select the desired setting.
● When numbers are displayed (e.g. title No.), the
numeric buttons can also be used for setting
instead of F/G.
● For some functions, the setting will be registered
immediately; for others, SELECT/ENTER must be
pressed.
To clear the GUI Menu Icons, press GUI
DISPLAY.
MENU
0
AUDIO SUBTITLE ANGLE
REPEAT
A-B
MARKER-SEARCH
RANDOM
ZOOM
Examples of GUI Menu Icons.
(The screens may differ depending on the disc contents.)
1
1
1/5
0:16:57
1 ENG
D
6 CH
1
OFF
16:57
1
STER.
NORM.
NORM.
(DVD GUI)
(CD GUI)
CHAPT
A
B
OFF
(DVD and CD GUI)
OPERATION USING GUI MENU ICONS
PAGE 21
Detailed description of each GUI menu icon
You can view information about a disc and its operational status on the TV screen.
Press GUI DISPLAY during
playback.
[TV screen] DVD GUI
1
1
0:16:57
1 ENG
D
6 CH
OFF
1
NORM.
Press GUI DISPLAY during
playback.
[TV screen] CD GUI
FUNCTION
(Press D/E to select desired item)
To show the current title No.
and to jump to the desired title No.
To show the current chapter No.
and to jump to the desired chapter No.
To show the elapsed time
and directly select scenes by the desired time.
To show the current audio soundtrack language,
encoding method, channel No.
and to change the settings.
To show the current subtitles language
and to change the setting.
To show the current angle No.
and to change the angle.
To show the current sound (NORMAL or 3D SURROUND)
and to change the setting.
FUNCTION
(Press D/E to select desired item)
To show the current track No.
1
and to jump to the desired track No.
SELECTION
METHOD
F/G, or
Numeric
SELECT/ENTER
F/G, or Numeric
SELECT/ENTER
SKIP
Numeric
SELECT/ENTER
F/G,
AUDIO
F/G,
SUBTITLE
F/G,
ANGLE
F/G,
3D SOUND
SELECTION
METHOD
F/G, or Numeric
SELECT/ENTER
SKIP
To show the elapsed time.
16:57
(Display only)
To show the current audio (STEREO, LEFT, RIGHT)
STER.
NORM.
and to select to the desired audio channel.
To show the current sound (NORMAL or 3D SURROUND)
and to change the setting.
Note
❍
Some DVD discs may not provide all of the above GUI menu icons.
F/G,
AUDIO
F/G,
3D SOUND
PAGE 22
ADVANCED OPERATION
Using a title menu
Some movie discs may contain two or more
titles. If the disc has a title menu recorded on it,
the TITLE button can be used to select the
movie title. (The details of operation differ
depending on the disc used.)
● Selecting a title may not be possible on
certain DVD discs.
1
PAUSE
/STEP
SELECT
/ENTER
OPEN/CLOSE
SETUP
GUI DISPLAY
2
2
RETURN
1
A list of the titles on the disc is displayed.
Pressing TITLE again to resume play from the scene
when TITLE was first pressed.
• Resume play may not be possible on certain discs.
STOP
2
Press TITLE.
2
3
Press D/E/F/G and press SELECT/ENTER or
PLAY, or press the numeric button(s), to
select desired title.
3D SOUND
4
5
6
7
8
9
PROGRAM
CLEAR
TITLE
MENU
0
AUDIO SUBTITLE ANGLE
REPEAT
A-B
MARKER-SEARCH
RANDOM
1
ZOOM
The selected title now starts playing.
Using a DVD menu
Some DVDs have unique menu structures called
DVD menus. For example, DVDs programmed
with complex contents provide guide menus, and
those recorded with various languages provide
menus for audio and subtitle language. Although
the DVD menu’s contents and operation differ
from disc to disc, the following explains the basic
operation when this feature is used.
1
PAUSE
/STEP
3
4
Pressing MENU again resumes play from the scene
when MENU was first pressed.
• Resume play may not be possible on certain discs.
SELECT
/ENTER
OPEN/CLOSE
SETUP
GUI DISPLAY
2
RETURN
1
2
3
4
5
6
7
8
9
The DVD menu available on the disc is now displayed.
1
2
STOP
2
Press MENU during play.
3D SOUND
2
Press D/E/F/G and press SELECT/ENTER, or
press the numeric button(s), to select desired
item.
PROGRAM
CLEAR
TITLE
MENU
0
AUDIO SUBTITLE ANGLE
REPEAT
A-B
MARKER-SEARCH
RANDOM
1
ZOOM
The selected item is now executed.
ADVANCED OPERATION
PAGE 23
Memorizing Settings for Viewed DVDs (Condition Memory)
This unit stores, in memory, settings for DVDs
you have watched. Settings remain in memory
even if you remove the disc from the player, or
switch power to the player OFF. If you load a
disc that has its settings memorized, the
“Resume disc from last position?” message will
appear on the TV screen. When you start playing the disc, the
memorized settings are automatically recalled.
You can memorize details for the following six settings.
Latest Stop Position (Page 18)
TV Aspect (Page 36)
Disc Audio Language (Page 24)
Disc Subtitle Language (Page 24)
Disc Menu Language (Page 33)
Angle (Page 25)
1
Load the DVD that has memorized.
It will appear on the TV screen as below
• If the screen is left for more than 10 seconds, playback will
start from the beginning of the title automatically.
POWER
Resume disc from
last position?
PLAY
SKIP
1. No
SKIP
2. Yes
STOP
2
PAUSE
/STEP
SELECT
/ENTER
OPEN/CLOSE
SETUP
2
GUI DISPLAY
RETURN
1
2
3
4
5
6
2
3D SOUND
Press F/G to select “Yes” and press
SELECT/ENTER.
The memorized settings are automatically recalled.
PROGRAM
7
8
9
CLEAR
TITLE
MENU
0
AUDIO SUBTITLE ANGLE
REPEAT
A-B
MARKER-SEARCH
RANDOM
ZOOM
SLOW/SCAN
REV
FWD
Notes
❍
❍
❍
❍
Settings are stored in memory for use any time.
You can store settings for up to 15 DVDs in memory. If you
memorize settings for more than 15 DVDs previously
memorized settings are erased in order from the least recently
memorized settings. Subsequently, if you try to call up these
previously memorized settings, you will get the latest settings
that have taken their place.
Switching of the audio mode etc., is automatic on some discs.
This unit does not store settings in memory, if you remove the
disc from the player or switch power to the player OFF when
DVD or title menu is displayed on the TV screen.
PAGE 24
ADVANCED OPERATION
Changing subtitle language
It is possible to change the subtitle language to a
different language from the one selected at the initial
settings. (See page 33 for further info.)
This operation works only with discs on which multiple
subtitle languages are recorded.
1
Press SUBTITLE during playback.
When no subtitles are recorded, “OFF” will be
displayed instead of the language number.
PROGRAM
7
8
1, 2
OFF
9
CLEAR
TITLE
MENU
0
AUDIO SUBTITLE ANGLE
REPEAT
A-B
MARKER-SEARCH
RANDOM
ZOOM
2
Number of the subtitle language being played
back.
Notes
❍
❍
❍
❍
In some cases, the subtitle language is not changed to
the selected one immediately.
When a disc supporting the closed caption is played, the
subtitle and the closed caption may overlap each other
on the TV screen. In this case, turn the subtitle off.
When the desired language is not selected even after
pressing the button several times, it means that the
language is not available on the disc.
When the power is turned on or the disc is removed,
subtitles appears in the language selected at the initial
settings. If this language is not recorded on the disc, the
disc’s priority language appears.
Press repeatedly SUBTITLE until the
desired language is selected.
1 ENG
To eliminate the On Screen Subtitles.
Press SUBTITLE repeatedly to select OFF at step 2.
Changing audio soundtrack language
It is possible to change the audio soundtrack language
to a different language from the one selected at the
initial settings in case of DVD disc. (See page 33 for
further info.) This operation works only with discs on
which multiple audio soundtrack languages are
recorded.
And it is possible to change the audio channel in case
of audio CD.
PROGRAM
7
8
9
CLEAR
TITLE
• DVD
Press AUDIO during play.
1
Number of the audio soundtrack language being
played back.
1 ENG
D
6 CH
2
MENU
Press AUDIO repeatedly until the
desired language is selected.
0
1, 2
AUDIO SUBTITLE ANGLE
REPEAT
A-B
2 FRE
D
6 CH
MARKER-SEARCH
RANDOM
ZOOM
• CD
Notes
❍
❍
❍
When the desired language is not selected even after
pressing the button several times, it means that the
language is not available on the disc.
When the power is turned on or the disc is removed, the
language heard is the one selected at the initial settings.
If this language is not recorded on the disc, only the
available language on the disc will be heard.
Some discs may not respond to Audio feature.
1
Press AUDIO during play.
STER.
2
Press AUDIO repeatedly until the
desired sound is selected.
LEFT
ADVANCED OPERATION
PAGE 25
Viewing from another angle
Some DVDs may contain scenes which have been
shot simultaneously from a number of different angles.
For these discs, the same scene can be viewed from
each of these different angles using the ANGLE button.
(The recorded angles differ depending on the disc
used.)
1
2
AUDIO SUBTITLE ANGLE
REPEAT
A-B
2
1
Press ANGLE repeatedly until the
desired angle is selected.
2
1, 2
ZOOM
For your reference
• The ANGLE indicator will blink in the DVD display window at scenes recorded at different angles to indicate
that angle switching is possible.
• The angle number can be programmed beforehand; the
angle will be switched to the selected number when the
ANGLE indicator blinks.
SLOW/SCAN
REV
Press ANGLE during playback.
Number of angle
being played back.
3
MARKER-SEARCH
RANDOM
1
FWD
Note
This function only works for discs having scenes recorded
at different angles.
❍
Producing a 3D SURROUND effect
This unit can produce a 3D Surround effect, using
SpatializerTM N-2-2TM technology, which simulates multichannel audio playback from two conventional stereo
speakers instead of the five or more speakers normally
required to listen to multi-channel audio from a home
theatre. This feature works with DVD discs encoded with
Dolby Pro Logic, Dolby Digital and DTS multi-channel
audio tracks.
1
Press 3D SOUND during playback.
Each time this button is pressed, the TV
screen display changes:
NORM.
2
Press 3D SOUND repeatedly until the
desired sound is selected.
PLAY
3D SUR
SKIP
SKIP
STOP
PAUSE
/STEP
Notes
SELECT
/ENTER
OPEN/CLOSE
SETUP
❍
GUI DISPLAY
❍
RETURN
1
2
3
3D SOUND
4
5
6
PROGRAM
7
8
9
1, 2
❍
This 3D Surround effect may not be available on some
DVD discs, such as those recorded with a mono audio
soundtrack.
Turn off the TV surround sound and other surround
effects when using this 3D surround effect.
For best 3D Surround effect using only two speakers it is
recommended that the two speakers be positioned
approximately 2m to 2.5m apart, and the listening
position should be 2m to 2.5m away from the speakers.
PAGE 26
ADVANCED OPERATION
Repeat Play
Repeating viewing (listening)
Repeating sections between two
specific points (A-B repeat)
Press REPEAT during playback.
Each time this button is pressed, the TV screen
changes as shown below and the disc will repeat a
chapter or title (DVD) or a track (CD).
1
Press A-B during play at the point where
repeat play is to start (A).
A
• DVD
Repeat of
chapter being
played
• You can select “OFF” at this step by pressing
CLEAR.
CHAPT
Repeat of title
being played
*
2
TITLE
Press A-B during play at the point where
repeat play is to be concluded (B).
OFF
Cancel repeat mode
(normal play)
A
Repeat play of the selection between points A
and B starts.
• CD
Repeat of track
being played
B
TRACK
To return to normal play
ALL
Repeat of entire
disc contents
Press A-B once “OFF” is displayed.
OFF
OFF
Cancel repeat mode
(normal play)
Notes
❍
To enjoy program repeat play (CD)
If REPEAT is pressed during program play, repeat play
is operated as below.
Repeat of the
current programmed
track
Repeat of all programs
❍
❍
❍
TRACK
ALL
OFF
Cancel repeat mode
(Program play)
To return to normal play
Press REPEAT several times until “OFF” is displayed.
Repeat play works only with discs for which the elapsed
playing time appears in the DVD display window during
playback.
Repeat play may not work correctly with some DVDs.
A-B repeat play works only within a title DVD or a track
CD.
Some subtitles recorded around point A or B may fail to
appear (DVD).
ADVANCED OPERATION
PAGE 27
Storing markers in memory to be viewed (listened to) again
Storing a MARKER in the DVD memory is similar
to marking your page in a book. It allows you to
quickly return to any point on the disc.
Storing a marker in the memory
1
Press MARKER during play at the starting
point to be viewed (listened to) again.
1/5
Indicates “1/5” is stored in the memory.
Up to 5 markers can be stored in the memory.
Recalling/Clearing a marker
POWER
2
Press SEARCH during playback.
PLAY
PLAY
SKIP
SKIP
Maker
Picture 1
Maker
Picture 2
Maker
Picture 3
Maker
Picture 4
Maker
Picture 5
Present
Picture
STOP
SELECT/
ENTER
PAUSE
/STEP
SELECT
/ENTER
OPEN/CLOSE
SETUP
GUI DISPLAY
RETURN
1
2
3
4
5
6
7
8
9
3D SOUND
3
Press D/E/F/G to select the marker to be
recalled/cleared.
4
Press PLAY or SELECT/ENTER to recall a
marker. or Press CLEAR to clear a marker.
PROGRAM
CLEAR
CLEAR
TITLE
MENU
0
AUDIO SUBTITLE ANGLE
REPEAT
A-B
MARKER-SEARCH
RANDOM
ZOOM
SEARCH
MARKER
Play resumes from the point corresponding to the
selected marker, or the selected marker is cleared.
● The “Present Picture” is not cleared.
SLOW/SCAN
REV
FWD
Notes
❍ These operations work only with discs for which the elapsed
playing time appears in the DVD display window during playback
or stop.
❍ Some subtitles recorded around the marker may fail to appear
(DVD).
❍ All the markers are cleared when the power is turned off or the
disc is removed and when TV Aspect mode is changed at the
SETUP menu.
❍ The marker is not stored when the DVD or title menu is
displayed on the TV screen.
PAGE 28
ADVANCED OPERATION
Zoom feature
The Zoom feature allows you to “ZOOM-IN” and
enlarge the picture on the screen to either 4 times (X4)
or 16 times (X16) its normal size.
SKIP
1
• The square frame will be displayed in the centre of
the picture. If no button is pressed for more than 10
seconds, the square frame will disappear.
• Each press of the ZOOM button changes the TV
screen in the left sequence.
• The magnification level will be displayed in the upper
right corner of the zoom area.
SKIP
STOP
PAUSE
/STEP
SELECT
/ENTER
OPEN/CLOSE
AUDIO SUBTITLE ANGLE
REPEAT
A-B
2
If you press D/E/F/G buttons the zoom
point shifts.
MARKER-SEARCH
RANDOM
1, 3
ZOOM
Press ZOOM during normal playback or
still playback.
2
Press SELECT/ENTER.
3
To resume normal playback
X4
The selected frame is displayed in full size on the
TV screen.
Press ZOOM again to cancel Zoom feature and
resume normal playback or still playback.
X16
Notes
(X4)
(X16)
(Normal)
Some discs may not respond to the Zoom feature.
Zoom does not work on subtitles or menus included on
DVD video discs.
❍
❍
Random play
Note: This function only works with karaoke DVD and
with audio CD discs. Random does not work with DVD
movies.
You can playback titles, or tracks in random order.
(Random playback)
The DVD player automatically selects the titles in a
DVD video karaoke disc only and plays them back
randomly.
Random play (DVD)
1
●
8
9
TITLE
If you press the RANDOM during normal playback, the DVD player will randomly select another title and begin random playback immediately.
2
PROGRAM
7
CLEAR
MENU
REPEAT
A-B
MARKER-SEARCH
RANDOM
ZOOM
1, 2
To resume normal playback, press
RANDOM.
The RANDOM indicator in the DVD display
window disappears.
0
AUDIO SUBTITLE ANGLE
Press RANDOM during stop.
The DVD player starts random playback.
Random play (CD)
The player plays the tracks on the disc in random order.
1
●
Press RANDOM during stop.
The random playback screen appears on the TV
screen.
If you press the RANDOM button during normal
playback, the DVD player immediately selects
another track and begins random playback.
Notes
❍
Random playback may not be possible on certain discs.
❍
If you press the SKIP
button during random
playback, the DVD player goes to another track
randomly and starts playback.
2
To resume normal playback, press
RANDOM during random playback.
The RANDOM indicator in the DVD display
window disappears.
ADVANCED OPERATION
PAGE 29
Program play
The player plays the tracks on the disc in an
order you specify.
1
Note: Program play function is possible only
with audio CDs. It does not work with DVD
movie discs.
Press PROGRAM during playback or stop
mode.
The program playback screen appears on the TV
screen.
Program
Step
1
Total Time 00:00
Clear All
POWER
• To exit the screen, press PLAY or PROGRAM.
3
PLAY
SKIP
2
SKIP
Press D/E/F/G and press the numeric
button(s), to select the desired track number.
STOP
3
PAUSE
/STEP
Program
SELECT
/ENTER
1
5
19
OPEN/CLOSE
SETUP
Step
3
Total Time 08:32
2
GUI DISPLAY
RETURN
1
2
3
4
5
6
3D SOUND
Clear All
PROGRAM
7
8
9
CLEAR
TITLE
MENU
0
AUDIO SUBTITLE ANGLE
REPEAT
A-B
MARKER-SEARCH
RANDOM
1
• Repeat step 2 to select another track.
• Up to 20 tracks can be programmed.
ZOOM
3
The selected track is stored in the memory and play
now begins in the programmed sequence.
● If you press PROGRAM to exit the screen, the
selected tracks are not memorized.
SLOW/SCAN
REV
Press PLAY or SELECT/ENTER to exit the
screen.
FWD
After playback of all tracks programmed
Play is stopped.
Clearing the program
●
To clear the program one by one
Press D/E/F/G to select the unwanted No. and then press
CLEAR.
●
To clear all the programs
Press D/E/F/G to select the “Clear All” and press
SELECT/ENTER. Press PLAY or SELECT/ENTER to exit the
screen. If you press PROGRAM to exit the screen, the programs are not cleared. (The programs are also cleared when
the power is turned off or the disc is removed.)
PAGE 30
ADVANCED OPERATION
Playback with MP3
To play an MP3 file
1
POWER
4
PLAY
SKIP
Load an MP3 disc.
The MP3 menu is displayed.
MP3
Program
ABCD
MP3-1
SKIP
MP3-2
STOP
2, 3,
4
MP3-3
MP3-4
PAUSE
/STEP
SELECT
/ENTER
MP3-5
OPEN/CLOSE
SETUP
MP3-6
2, 3
GUI DISPLAY
MP3-7
MP3-8
MP3-9
Clear All
RETURN
1
2
3
4
5
6
7
8
9
3D SOUND
2
PROGRAM
CLEAR
TITLE
MENU
0
AUDIO SUBTITLE ANGLE
REPEAT
A-B
MP3
MARKER-SEARCH
RANDOM
Press D/E buttons to select the directory where
MP3 files that you want to play are located and
then press SELECT/ENTER.
Program
MP3-1
ZOOM
..
TRACK_1
TRACK_2
TRACK_3
To play an MP3 file repeatedly
TRACK_4
● If you press REPEAT button once during play,
TRACK_5
the current MP3 file will play repeatedly.
● If you press REPEAT button twice during play,
the directory will play repeatedly.
● If you press REPEAT button three times, the
repeat play will be cancelled.
TRACK_7
MP3
MP3-1
..
Pr
MP3
TRACK_6
TRACK_8
3
..
..
TRACK_1
TRACK_1
TRACK_2
TRACK_2
TRACK_3
TRACK_3
TRACK_4
TRACK_4
TRACK_5
TRACK_5
TRACK_6
TRACK_6
TRACK_7
TRACK_7
TRACK_8
TRACK_8
Notes
❍
❍
❍
❍
Program
MP3-1
MP3-1
TRACK_1
TRACK_2
TRACK_3
TRACK_4
TRACK_5
TRACK_6
TRACK_7
TRACK_8
The directory and file name is only to display with
English.
If there is an impossible code to display, it will be
displayed under lined (_) instead of English.
If a directory has no MP3 file, the “
” is displayed
with the directory name.
E during
If you select another file by pressing D/E
playback, the file is played after 5 seconds
automatically.
E during
If you select a directory by pressing D/E
playback, the playback is stopped after 5 seconds.
Clear All
If you want to return to the previous menu, press
RETURN button.
REPEAT symbol
❍
Press D/E button to select the desired MP3 file
of the selected directory on your disc.
MP3
Pr
Clear All
4
Press SELECT/ENTER or PLAY to start
playback of a file.
For your reference
• Press SKIP
or SKIP
to play the next file or previous
file during playback.
• Press TITLE to move to 1’st page of current directory during
playback and press TITLE again to move to the next page
within 5 seconds.
• Press MENU to move to the Root Directory during playback.
ADVANCED OPERATION
PAGE 31
Playback with MP3
To program play an MP3 file
POWER
4
PLAY
SKIP
SKIP
1
Follow steps 1 to 2 on previous page.
2
Select an MP3 file to program with D/E.
MP3
STOP
4
Program
MP3-1
PAUSE
/STEP
SELECT
/ENTER
..
OPEN/CLOSE
SETUP
TRACK_1
2, 4
GUI DISPLAY
TRACK_2
TRACK_3
TRACK_4
RETURN
1
2
TRACK_5
3
TRACK_6
3D SOUND
4
5
TRACK_7
6
TRACK_8
PROGRAM
7
8
CLEAR
TITLE
MENU
0
AUDIO SUBTITLE ANGLE
REPEAT
A-B
3
MARKER-SEARCH
RANDOM
Press PROGRAM button to add an MP3 file
on the program list.
ZOOM
MP3
MP3-1
..
To play an MP3 file repeatedly
TRACK_2
TRACK_2
TRACK_7
TRACK_7
TRACK_6
TRACK_6
TRACK_9
TRACK_9
TRACK_7
TRACK_1
TRACK_6
TRACK_2
TRACK_9
TRACK_5
TRACK_6
TRACK_7
TRACK_8
Clear All
• Repeat steps 2 - 3 to select another track.
• Up to 60 files can be programmed.
4
Press G button and select the desired MP3
file and press SELECT/ENTER or PLAY button
to play.
MP3
MP3-1
..
Clear All
Clear All
TRACK_2
TRACK_4
the current MP3 file will play repeatedly.
● If you press REPEAT button twice during play,
the all MP3 files on the program list will play
repeatedly.
● If you press REPEAT button three times, the
repeat play will be cancelled.
Program
Program
TRACK_3
● If you press REPEAT button once during play,
Program
Clear All
3
9
Program
TRACK_2
TRACK_7
TRACK_1
TRACK_6
TRACK_2
TRACK_9
TRACK_3
TRACK_4
TRACK_5
REPEAT symbol
TRACK_6
TRACK_7
TRACK_8
Clearing the program
●
To clear the program one by one
Press D/E/F/G to select the unwanted MP3 file on
the program list and then press CLEAR.
●
To clear all the programs
Press D/E/F/G to select the “Clear All” and press
SELECT/ENTER.
Clear All
If you want to enter the main menu, press F button.
After playback all tracks programmed
Play is stopped.
PAGE 32
INITIAL SETTINGS
Common procedures of initial settings
Once the initial settings have been completed,
the player can always be operated under the
same conditions (especially with DVD discs).
The settings will be retained in the memory until
they are changed, even if the power is switched
off.
Common procedures of initial settings
1
Press SETUP in the stop or playback mode.
The SETUP menu is displayed.
Disc Audio
Original
Disc Subtitle
English
Disc Menu
French
Rating
German
Password
Spanish
TV Aspect
Italian
Menu Language
Chinese
TV Output Select
Polish
Pseudo PAL
Hungarian
Digital Audio Output
Russian
5.1 Speaker Setup
Other — — — —
POWER
2
SKIP
3
1
SKIP
• Disc Audio (see page 33)
• Disc Subtitle (see page 33)
• Disc Menu (see page 33)
• Rating (see page 34)
• Password (see page 35)
• TV Aspect (see page 36)
• Menu Language (see page 37)
• TV Output Select (see page 37)
• Pseudo PAL (see page 38)
• Digital Audio Output (see page 39)
• 5.1 Speaker Setup (see page 40)
STOP
PAUSE
/STEP
Press D/E to select the desired item.
The screen will show the current setting for the
selected item, and the alternate setting(s).
PLAY
SELECT
/ENTER
OPEN/CLOSE
SETUP
GUI DISPLAY
2, 3
RETURN
1
2
3
4
5
6
7
8
9
3D SOUND
PROGRAM
CLEAR
TITLE
MENU
0
AUDIO SUBTITLE ANGLE
REPEAT
A-B
MARKER-SEARCH
RANDOM
ZOOM
3
Press G and then D/E to select the desired
setting and press SELECT/ENTER.
• Some items require additional steps. (See the
respective page.)
SLOW/SCAN
REV
FWD
When the alternate setting is selected the screen returns to
the Initial Settings display.
To exit SETUP menu
Press SETUP, RETURN or PLAY.
INITIAL SETTINGS
PAGE 33
Selecting disc languages
This is to select the audio soundtrack language,
subtitle language and the language used in title
menus or DVD menus which will always be used
for every disc to be played back.
1
At the setup screen, press D/E to select
“Disc Audio” and press G.
When you play back a DVD video disc, the DVD
player automatically displays the pre-selected
subtitle language if it is included on the disc.
2
Disc Audio
Original
Disc Subtitle
English
Disc Menu
French
Rating
German
Password
Spanish
TV Aspect
Italian
Menu Language
Chinese
TV Output Select
Polish
Pseudo PAL
Hungarian
Digital Audio Output
Russian
5.1 Speaker Setup
Other — — — —
Press D/E to select the desired language and
then press SELECT/ENTER.
POWER
Original :The original language of each disc will be selected.
English : The English will be Selected.
Other : Another language can be selected. You can input
4-digit language code. (Refer to the language
codes on page 41. Press CLEAR if an incorrect
language code is entered.)
PLAY
SKIP
SKIP
STOP
2
PAUSE
/STEP
SELECT
/ENTER
OPEN/CLOSE
SETUP
1, 2
GUI DISPLAY
The “Disc Subtitle” and “Disc Menu” are selected by the
same method.
Note
RETURN
1
2
3
4
5
6
7
8
9
3D SOUND
PROGRAM
CLEAR
TITLE
MENU
0
AUDIO SUBTITLE ANGLE
REPEAT
A-B
MARKER-SEARCH
RANDOM
ZOOM
SLOW/SCAN
REV
FWD
❍
If the language selected is not available on the disc, the original
language designated by each disc will be selected.
PAGE 34
INITIAL SETTINGS
Selecting rating level and password
This is to prohibit the playing of specified
DVDs which are unsuitable for children.
● Some DVD discs contain a restriction level
which enables parents to remove scenes or
prevent playback of discs by children. DVD
players are equipped with a password
designed to prevent children changing the
level.
Selecting rating level (DVD only)
1
At the SETUP screen, press
“Rating” and press G.
D/E
Disc Audio
8
Disc Subtitle
7
Disc Menu
6
Rating
5
Password
4
TV Aspect
3
Menu Language
2
TV Output Select
1
Pseudo PAL
Unlock
to select
Digital Audio Output
5.1 Speaker Setup
POWER
2
PLAY
SKIP
SKIP
STOP
2
PAUSE
/STEP
SELECT
/ENTER
OPEN/CLOSE
SETUP
1, 2
GUI DISPLAY
RETURN
1
2
3
3D SOUND
4
5
6
PROGRAM
7
Press D/E to select the desired level and
press SELECT/ENTER.
8
TITLE
8 Blocked
Disc Subtitle
7 Blocked
Disc Menu
6
Rating
5
Password
4
TV Aspect
3
Menu Language
2
TV Output Select
1
Pseudo PAL
Unlock
Digital Audio Output
5.1 Speaker Setup
9
CLEAR
Disc Audio
MENU
0
AUDIO SUBTITLE ANGLE
REPEAT
A-B
MARKER-SEARCH
RANDOM
ZOOM
You cannot play DVD video discs rated higher than the level
you selected unless you cancel the parental lock function.
For example, when you select level 7, discs rated higher than
level 7 are blocked and cannot be played.
SLOW/SCAN
REV
FWD
If you change the level and enter a password, playback of all
DVDs with ratings higher than your selection will be blocked,
unless the correct password is entered again. For example: if
you change the level to “5”, the DVD player will not play discs
with ratings of “6”, “7” or “8” unless the correct password is
entered on the remote control.
INITIAL SETTINGS
PAGE 35
Selecting rating level and password
Setting your password (DVD only)
If you change the rating level to “7” or lower, you must enter
a 4-digit “password” to prevent playback of discs with higher
ratings.
POWER
1
PLAY
SKIP
At the SETUP screen, press
“Password” and press G.
SKIP
————
Rating
PAUSE
/STEP
SELECT
/ENTER
Password
OPEN/CLOSE
SETUP
TV Aspect
1
GUI DISPLAY
Menu Language
TV Output Select
Pseudo PAL
Digital Audio Output
RETURN
1
2, 3
NEW
Disc Subtitle
to select
Disc Menu
STOP
2, 3
Disc Audio
E
2
3
5.1 Speaker Setup
3D SOUND
4
5
6
7
8
9
PROGRAM
CLEAR
TITLE
MENU
2
0
AUDIO SUBTITLE ANGLE
REPEAT
A-B
Example : 1234
Do not forget your password.
MARKER-SEARCH
RANDOM
Input a 4-digit password and press
SELECT/ENTER.
ZOOM
3
Input the 4-digit password again and press
SELECT/ENTER to verify.
Setting is finished.
SLOW/SCAN
REV
FWD
● The rating is locked. Any discs whose rating is higher than
the setting cannot be played back unless the correct
password is entered.
To change/clear memorized password
1
2
To clear your 4-digit password
If you forget your password, to clear the
current password, follow the procedure below.
At the SETUP screen, press E to select
“Password” and press G.
Input your password and Press
SELECT/ENTER.
Disc Audio
Change
Disc Subtitle
Clear
Disc Menu
Rating
Password
1
2
Menu Language
TV Output Select
Pseudo PAL
Digital Audio Output
Enter 6-digit number “210499” and
then press SELECT/ENTER.
The 4-digit password is cleared.
3
TV Aspect
At the SETUP screen
Press E to select “Password” item.
Enter a new password
Refer to “Setting your password” section on the
right.
5.1 Speaker Setup
3
To change or clear your password, press D/E
to select the “Change” or “Clear” and press
SELECT/ENTER.
To change the rating level/password, follow the steps on
page 34-35 again.
PAGE 36
INITIAL SETTINGS
Selecting TV Aspect
Select the appropriate screen type according to
your TV set; conventional size screen (4:3) or
wide-screen (16:9).
1
POWER
At the SETUP screen, press D/E to select “TV
Aspect” and press G.
Disc Audio
4:3 Letterbox
Disc Subtitle
4:3 Panscan
Disc Menu
16:9 Wide
Rating
Password
TV Aspect
Menu Language
PLAY
TV Output Select
SKIP
Pseudo PAL
SKIP
Digital Audio Output
STOP
2
PAUSE
/STEP
5.1 Speaker Setup
SELECT
/ENTER
OPEN/CLOSE
SETUP
GUI DISPLAY
RETURN
1
2
3
4
5
6
1, 2
2
Press D/E to select the desired Aspect and
press SELECT/ENTER.
3D SOUND
PROGRAM
7
8
9
CLEAR
TITLE
MENU
4:3 Letterbox
Disc Subtitle
4:3 Panscan
Disc Menu
16:9 Wide
Rating
0
Password
AUDIO SUBTITLE ANGLE
REPEAT
Disc Audio
A-B
TV Aspect
MARKER-SEARCH
RANDOM
Menu Language
ZOOM
TV Output Select
Pseudo PAL
Digital Audio Output
5.1 Speaker Setup
SLOW/SCAN
REV
FWD
4:3 Letterbox : The video material not formatted in the Pan
& Scan style is played back in the letterbox style (black
bands appear at top and bottom of screen).
4:3 Panscan : Select when a conventional TV set is
connected. The video material formatted in the Pan & Scan
style is played back in that style (the left and right edges are
cut off).
16:9 Wide : Select when a wide-screen TV set is connected.
Played in “FULL” size. (Setting the wide-screen TV to “FULL”
mode is also necessary.)
4:3 Letterbox
Cut Off
* Each screen shows an example when the video material
for a wide-screen is played.
(This setting does not affect the video material for
conventional size.)
4:3 Panscan
16:9 Wide
INITIAL SETTINGS
PAGE 37
Selecting Menu Language
Selects language for DVD menus and displays
on the TV.
1
POWER
At the SETUP screen, press D/E to select
“Menu Language” and press G.
Disc Audio
English
Disc Subtitle
Spanish
Disc Menu
French
Rating
German
Password
Italian
TV Aspect
Menu Language
TV Output Select
PLAY
Pseudo PAL
SKIP
Digital Audio Output
SKIP
5.1 Speaker Setup
STOP
2
PAUSE
/STEP
SELECT
/ENTER
OPEN/CLOSE
SETUP
1, 2
GUI DISPLAY
2
RETURN
1
2
3
3D SOUND
4
5
6
PROGRAM
7
8
Disc Audio
English
Disc Subtitle
Spanish
Disc Menu
French
Rating
German
Password
Italian
TV Aspect
9
CLEAR
Press D/E to select the desired Language
and press SELECT/ENTER.
TITLE
Menu Language
MENU
TV Output Select
0
Pseudo PAL
Digital Audio Output
5.1 Speaker Setup
Selecting TV Output
It can be used to select the video output
between S-VIDEO OUT and SCART’s
RGB signal (component).
1
At the SETUP screen, press D/E to select “TV
Output Select” and press G.
Disc Audio
S-Video
Disc Subtitle
Component
Disc Menu
POWER
Rating
Password
TV Aspect
Menu Language
PLAY
TV Output Select
Pseudo PAL
SKIP
SKIP
Digital Audio Output
5.1 Speaker Setup
STOP
2
PAUSE
/STEP
SELECT
/ENTER
OPEN/CLOSE
SETUP
1, 2
GUI DISPLAY
RETURN
1
2
3
3D SOUND
4
5
8
CLEAR
0
Disc Audio
S-Video
Disc Subtitle
Component
Disc Menu
Password
TV Aspect
9
TITLE
Press D/E to select the desired TV Output
and press SELECT/ENTER.
Rating
6
PROGRAM
7
2
MENU
Menu Language
TV Output Select
Pseudo PAL
Digital Audio Output
5.1 Speaker Setup
PAGE 38
INITIAL SETTINGS
Selecting Pseudo PAL
Depending on a disc, you can play a NTSC DVD
disc by Pseudo PAL ON mode.
1
At the SETUP screen, press D/E to select
“Pseudo PAL” and press G.
Disc Audio
On
Disc Subtitle
Off
Disc Menu
Rating
POWER
Password
TV Aspect
Menu Language
TV Output Select
PLAY
Pseudo PAL
Digital Audio Output
SKIP
SKIP
5.1 Speaker Setup
STOP
2
PAUSE
/STEP
SELECT
/ENTER
OPEN/CLOSE
SETUP
GUI DISPLAY
1, 2
2
RETURN
1
2
3
4
5
6
Press D/E to select the desired mode and
press SELECT/ENTER.
3D SOUND
PROGRAM
7
8
9
CLEAR
TITLE
Disc Audio
On
Disc Subtitle
Off
Disc Menu
MENU
Rating
0
Password
AUDIO SUBTITLE ANGLE
TV Aspect
MARKER-SEARCH
Menu Language
REPEAT
A-B
RANDOM
TV Output Select
ZOOM
Pseudo PAL
Digital Audio Output
5.1 Speaker Setup
SLOW/SCAN
REV
FWD
Notes
❍
❍
❍
The Pseudo PAL can be displayed when the SYSTEM selector
on the rear panel is switched to PAL mode.
If there are some problems during playback of a NTSC disc,
select the “Pseudo PAL” to “On” mode.
The picture can be streamed according to TV type when the
“Pseudo PAL” is “On” mode.
INITIAL SETTINGS
PAGE 39
Selecting Digital Audio Output
Each DVD disc has a variety of audio output
options. Set the player’s Digital Audio Output
according to the type of audio system you use.
1
At the SETUP screen, press D/E to select
Digital Audio Output and press G.
POWER
Disc Audio
DOLBY
DIGITAL
Disc Subtitle
Stream/PCM
Disc Menu
PCM
/PCM
Rating
Password
TV Aspect
Menu Language
PLAY
TV Output Select
SKIP
Pseudo PAL
SKIP
Digital Audio Output
STOP
2
PAUSE
/STEP
5.1 Speaker Setup
SELECT
/ENTER
OPEN/CLOSE
SETUP
GUI DISPLAY
1, 2
2
Press D/E to select the desired output and
press SELECT/ENTER.
RETURN
1
2
3
3D SOUND
4
5
6
PROGRAM
7
8
DOLBY
DIGITAL
Disc Subtitle
Stream/PCM
Disc Menu
PCM
/PCM
Rating
9
CLEAR
Disc Audio
Password
TITLE
MENU
TV Aspect
0
Menu Language
AUDIO SUBTITLE ANGLE
REPEAT
A-B
MARKER-SEARCH
RANDOM
TV Output Select
Pseudo PAL
ZOOM
Digital Audio Output
5.1 Speaker Setup
SLOW/SCAN
REV
FWD
DOLBY DIGITAL/PCM: Select “DOLBY DIGITAL/PCM” if
an active digital output is supplied to a Dolby Digital decoder,
(or an amplifier or other equipment with Dolby Digital
decoder).
Stream/PCM: Select “Stream/PCM” if an active
digital output is supplied to an amplifier or other
equipment with DTS decoder, Dolby Digital decoder and
MPEG decoder.
PCM: Select “PCM” if an active digital output is
supplied to an amplifier or other equipment with linear PCM
only (or MD recorder or DAT deck).
OUTPUT
Playback
Disc
Stream/PCM
Dolby Digital/
PCM
PCM only
96 kHz
Linear PCM
DVD
PCM
PCM
PCM
DTS DVD
DTS bit Stream
Not Output
Not Output
Dolby Digital
DVD
Dolby Digital
bit Stream
Dolby Digital
bit Stream
PCM
MPEG DVD
MPEG bit Stream PCM
PCM
Audio CD
PCM
PCM
PCM
DTS Audio CD
DTS bit Stream
DTS bit Stream
DTS bit Stream
Notes
❍
❍
❍
When you are not using the player’s digital audio output, don’t
select any of the options.
If an active digital audio output signal is supplied to a receiver or
other equipment without a corresponding digital decoding capability, a very loud noise may be produced which could
permanently damage the speakers.
The DTS DVD disc sound is played back only when the DVD
player is connected to a receiver with a DTS decoder.
PAGE 40
INITIAL SETTINGS
Selecting Speaker
Select the speaker to adjust the audio output
mode of the speaker.
1
At the SETUP screen, press D/E to select
“5.1 Speaker Setup” and press G.
Front Speaker (L/R)
STOP
1, 2
PAUSE
/STEP
Disc Audio
Centre Speaker
Disc Subtitle
SELECT
/ENTER
OPEN/CLOSE
SETUP
GUI DISPLAY
1, 2
RETURN
1
2
3
4
5
6
7
8
9
R
R
Disc Menu
3D SOUND
Sub Woofer
Rating
Front L/R
Password
Volume:
TV Aspect
Size
Menu Language
Delay :
TV Output Select
Test
Pseudo PAL
Return
:
dB
Large
Rear Surround
Speaker (L/R)
ms
Digital Audio Output
5.1 Speaker Setup
PROGRAM
CLEAR
TITLE
MENU
0
2
Press F/G to select the desired speaker and
press D/E/F/G to adjust options.
Disc Audio
Note
❍
❍
Do not place the centre or rear speakers farther
away from the listening position than the front
speakers.
The test tone does not output from the subwoofer.
Disc Subtitle
R
R
Disc Menu
Rating
Rear L/R
Password
Volume:
TV Aspect
Size
Menu Language
Delay :
TV Output Select
Test
Pseudo PAL
Return
:
0 dB
Large
2 ms
Digital Audio Output
5.1 Speaker Setup
Volume: Press F/G to adjust the output level of
selected speaker. (-6dB ~ 0dB)
Size: Press F/G to set a mode. (Large, Small, None)
• If you have connected the system to a speaker
with low frequency of 100Hz or below, select
“Large”
• If you have connected the system to a speaker
without low frequency of 100Hz or below, select
“Small” But if you haven’t connected to sub
woofer, always select “Large” of Front Speaker
(L/R).
• When you don’t connect to speaker, select “None”.
• Front L/R speaker’s size can be selected to Large”
or “Small”.
• If Front L/R speaker’s size is selected to “Small”,
Rear and Centre speaker’s size can be selected to
“Small” or “None”, and Sub woofer speaker’s size
can be selected only to “Large”.
Delay: Press F/G to customize the sound to conform
to the acoustics of your room by adding a delay
effect to the sound of the Centre Speaker and
Surround Speaker.
• When 5.1CH Surround is played, you can enjoy
the best sound if the distance between you and
each speaker is same. You can set Delay time in
the Centre/Surround Speaker to customize the
sound to to the acoustic of your room.
(A)
L
R
C
DC
DF
SW
DS
SL
SR
(B)
• Setting Centre Speaker
If the distance of DC is
equal to or longer than
the DF in the left figure,
set the mode as 0ms.
Otherwise, change the
setting according to the
table below.
(A) = DF - DC
Distance of (A)(cm) Setting(ms)
34
1
68
2
102
3
136
4
170
5
• Setting Rear Surround Speaker
If the distance of DF is equal to the distance of DS
in the above, set the mode as 0ms. Otherwise,
change the setting according to the table below.
(B) = DF - DS
Distance of (B)(cm)
170
340
510
Setting(ms)
5
10
15
Test : Press SELECT/ENTER to test signals of each
speaker. Adjust Volume to match to the volume of
test signals memorized in the system.
• Front (L) → Front (R) → Centre → Rear (L) → Rear (R)
Return: Press SELECT/ENTER to return to the
previous menu screen.
INITIAL SETTINGS
PAGE 41
Table of Language and Their Abbreviations
Enter the appropriate code number for the initial settings “Audio”, “Subtitle” and/or “Menu” (See page 33).
Code
Language
Code
Language
Code
Language
Code
Language
6565
Afar
7079
Faroese
7678
Lingala
8375
Slovak
6566
Abkhazian
7082
French
7679
Laothian
8376
Slovenian
6570
Afrikaans
7089
Frisian
7684
Lithuanian
8377
Samoan
6577
Ameharic
7165
Irish
7686
Latvian, Lettish
8378
Shona
6582
Arabic
7168
Scots Gaelic
7771
Malagasy
8379
Somali
6583
Assamese
7176
Galician
7773
Maori
8381
Albanian
6588
Aymara
7178
Guarani
7775
Macedonian
8382
Serbian
6590
Azerbaijani
7185
Gujarati
7776
Malayalam
8385
Sundanese
6665
Bashkir
7265
Hausa
7778
Mongolian
8386
Swedish
6669
Byelorussian
7273
Hindi
7779
Moldavian
8387
Swahili
6671
Bulgarian
7282
Croatian
7782
Marathi
8465
Tamil
6672
Bihari
7285
Hungarian
7783
Malay
8469
Telugu
6678
Bengali; Bangla
7289
Armenian
7784
Maltese
8471
Tajik
6679
Tibetan
7365
Interlingua
7789
Burmese
8472
Thai
6682
Breton
7378
Indonesian
7865
Nauru
8473
Tigrinya
6765
Catalan
7383
Icelandic
7869
Nepali
8475
Turkmen
6779
Corsican
7384
Italian
7876
Dutch
8476
Tagalog
6783
Czech
7387
Hebrew
7879
Norwegian
8479
Tonga
6789
Welsh
7465
Japanese
7982
Oriya
8482
Turkish
6865
Danish
7473
Yiddish
8065
Panjabi
8484
Tatar
6869
German
7487
Javanese
8076
Polish
8487
Twi
6890
Bhutani
7565
Georgian
8083
Pashto, Pushto
8575
Ukrainian
6976
Greek
7575
Kazakh
8084
Portuguese
8582
Urdu
6978
English
7576
Greenlandic
8185
Quechua
8590
Uzbek
6979
Esperanto
7577
Cambodian
8277
Rhaeto-Romance
8673
Vietnamese
6983
Spanish
7578
Kannada
8279
Rumanian
8679
Volapük
6984
Estonian
7579
Korean
8285
Russian
8779
Wolof
6985
Basque
7583
Kashmiri
8365
Sanskrit
8872
Xhosa
7065
Persian
7585
Kurdish
8368
Sindhi
8979
Yoruba
7073
Finnish
7589
Kirghiz
8372
Serbo-Croatian
9072
Chinese
7074
Fiji
7665
Latin
8373
Singhalese
9085
Zulu
PAGE 42
REFERENCE
Disc Requirements/Copyright Information
Playable Discs
This DVD player can play back the following discs.
Disc mark
Contents
Disc size
Maximum playback time
Approx. 4 hours (single sided disc)
12 cm
DVD video discs
Approx. 8 hours (double sided disc)
Audio+Video
(moving pictures)
Approx. 80 minutes (single sided disc)
8 cm
Approx. 160 minutes (double sided disc)
Audio CDs
12 cm
74 minutes
8 cm
20 minutes
Audio
You can play back CD-R and CD-RW disc also. You cannot playback discs other than those listed above. (Video
CD, CD-ROM, CD-Extra, CD-G, photo CD, and CD-i discs can not be played on this DVD player.)
“Certain audio features of this product manufactured under a license from Desper Products, Inc.,
Spatializer® 3-D Stereo, Spatializer N-2-2 (TM) and the circle-in-square device are trademarks owned by Desper
Products, Inc,.”
Region Management Information
Region Management Information: This DVD Player is designed and manufactured to respond to the Region
Management Information that is recorded on a DVD disc. If the Region number described on the DVD disc does
not correspond to the Region number of this DVD player, this DVD player cannot play that disc.
The Region number of this DVD player is 2.
2
Notes on Unauthorized Discs
You may not be able to play back some DVD video discs on this player if they were purchased from outside your
geographic area or made for business purposes.
When you try to play back an unauthorized disc, “Check Regional Code” appears on the TV screen.
Notes on Copyright
It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, and rent copyrighted material
without permission.
DVD video discs are copy protected, and any recordings made from these discs will be distorted.
This product incorporates copyright protection technology that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of
this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home
and other limited viewing uses only, unless otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
REFERENCE
PAGE 43
Before Calling Service Personnel
Symptoms and Correction
Check the following guide for the possible cause of a problem before contacting service.
Symptom
Cause
Correction
No power.
• The power cord is disconnected.
• Plug the power cord into the wall outlet
securely.
The power is on, but
the DVD player does
not work.
• No disc is inserted.
• Insert a disc. (Check that the DVD or,
audio CD indicator in the DVD display is
lit.)
No picture.
• The TV is not set to receive DVD signal
output.
• Select the appropriate video input mode
on the TV so the picture from the DVD
player appears on the TV screen.
• The video cable is not connected
securely.
• Connect the video cable into the jacks
securely.
• The connected TV power is turned off.
• Turn on the TV.
• The equipment connected with the
audio cable is not set to receive DVD
signal output.
• Select the correct input mode of the
audio receiver so you can listen to the
sound from the DVD player.
• The audio cables are not connected
securely.
• Connect the audio cable into the jacks
securely.
• The power of the equipment connected
with the audio cable is turned off.
• Turn on the equipment connected with
the audio cable.
• The Digital Audio Output is set to the
wrong position.
• Set the Digital Audio Output to the
correct position, then turn on the DVD
player again by pressing the POWER
button.
The playback picture is poor.
• The disc is dirty.
• Clean the disc.
The DVD player does
not start playback.
• No disc is inserted.
• Insert a disc.(Check that the DVD, or
audio CD indicator in the DVD display is
lit.)
• An unplayable disc is inserted.
• Insert a playable disc. (Check the disc
type, color system and Regional code.)
• The disc is placed upside down.
• Place the disc with the playback side
down.
• The disc is not placed within the guide.
• Place the disc on the disc tray correctly
inside the guide.
• The disc is dirty.
• Clean the disc.
• A menu is on the TV screen.
• Press the SETUP button to turn off the
menu screen.
• The Rating level is set.
• Cancel the Rating function or change
the rating level.
• The remote control is not pointed at the
remote sensor of the DVD player.
• Point the remote control at the remote
sensor of the DVD player.
• The remote control is too far from the
DVD player.
• Operate the remote control within about
23 ft (7 m).
• There is an obstacle in the path of the
remote control and the DVD player.
• Remove the obstacle.
• The batteries in the remote control are
exhausted.
• Replace the batteries with new ones.
No sound.
The remote control
does not work properly.
PAGE 44
REFERENCE
Specifications
[Supplied
Accessories]
[Outputs]
[DVD player]
DVD player/Outputs/Supplied Accessories
Power supply
AC 100-240V, 50/60 Hz
Power consumption
16 W
Mass
7.1 lbs (3.2 kg)
External dimensions (W X H X D)
17” X 3.5” X 8.46” (430 x 88 x 215 mm)
Signal system
PAL 625/50, NTSC 525/60
Laser
Semiconductor laser, wavelength 650 nm
Frequency range (audio)
4 Hz to 20 kHz
Signal-to-noise ratio (audio)
More than 100 dB (EIAJ)
Dynamic range (audio)
More than 95 dB (EIAJ)
Harmonic distortion (audio)
0.008 %
Wow and flutter
Below measurable level (less than + 0.001 % (W.PEAK)) (EIAJ)
Operating conditions
Temperature: 41°F to 95°F, Operation status: Horizontal
Video output
1.0 V (p-p), 75 Ω, negative sync., RCA jack x 1/SCART(TO TV)
S-video output
(Y) 1.0 V (p-p), 75 Ω, negative sync., Mini DIN 4-pin x 1
(C) 0.286 V (p-p), 75 Ω,
Audio output (digital audio)
0.5 V (p-p), 75 Ω, RCA jack x 1
Audio output (optical audio)
Optical connector x 1
Audio output (analog audio)
2.0 Vrms(1 KHz, 0 dB), 330 Ω, RCA jack (L, R) x 1/SCART(TO TV)
●
S-video cable .............................................................................................1
●
Video cable ................................................................................................1
●
Audio cable ................................................................................................1
●
Remote control...........................................................................................1
❋ Designs and specifications are subject to change without notice.
Technology with the human touch
GUARANTEE
● LG Electronics U.K. Ltd. will provide the following services in order to expedite this Guarantee.
1. All faulty components which fail due to defective manufacture will be replaced free of charge for a
period of 12 months from the original date of purchase.
2. The dealer (or his service agent) who sold the product will be reimbursed for any labour provided
in the repair of this LG equipment, for a period of 12 months from the original date of purchase.
These claims must be made in accordance with the published scale of service charges and
relevant claims procedure.
PLEASE NOTE:
A. The dealer may restrict the guarantee to the original purchaser.
B. The dealer is not obliged to carry out service under guarantee if unauthorized modifications are
made to the apparatus, or if non standard components are used or if the serial number of the
apparatus is removed, defaced, misused, or altered.
C. Any claims made under guarantee must be directed to the dealer from whom the equipment was
originally purchased. The dealer may, before carrying out service under guarantee, require a
receipted account as evidence of the date of purchase.
D. We respectfully point out that your dealer is not obligated to replace batteries if they become
exhausted or worn in use.
E. Aerial alignment and consumer control adjustments are not covered by this guarantee.
This guarantee does not affect your statutory rights.
● REQUIREMENTS TO MAINTAIN WARRANTY COVERAGE:
RETAIN YOUR RECEIPT TO PROVE DATE OF PURCHASE. A COPY OF YOUR RECEIPT MUST BE
SURRENDERED AT THE TIME GUARANTEE SERVICE IS PROVED.
● Product Registration Card :
It is helpful to complete at least your name, address, phone,
model & serial numbers and return it. This will enable LG to
assist you in the future should you lose your receipt, your
units be stolen, or should modifications be necessary.
● To obtain information or assistance:
Call 01753 500470 Monday-Friday 9.00am-4.30pm
MODEL NO.*
*
SERIAL NO.*
DATE OF PURCHASE.*
Please complete for your own record
In all cases of difficulty - consult your LG dealer
from whom the product was purchased
P/NO: 3834RS0013C