Model number
Serial number
:
:
LG DLP PROJECTOR
Please read this manual carefully before operating
your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the bottom of the set and
quote this information to your dealer when you
require service.
HS101
OWNER’S MANUAL
DLP PROJECTOR
FCC NOTICE
• A Class A digital device
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
Warning
This is a class A product. In a domestic environment this product may cause radio interference, in
which case the user may be required to take adequate measures.
Contents
Contents
Safety Instructions ....................................4
Names of parts
Main Body .......................................................7
Connecting Part ..............................................7
Control Panel ..................................................8
Accessories.....................................................9
Optional Extras ...............................................9
Installing and Composition
Installation Instructions ...................................10
How to install the projector using the tripod ...11
Basic Operation of the Projector.....................12
Using Kensington Security System.................13
Turning on the Projector .................................14
Turning off the Projector .................................14
Focus and Position of the Screen Image........14
Selecting source mode ...................................14
Connection
Connecting
Connecting
Connecting
Connecting
Connecting
to
to
to
to
to
a
a
a
a
a
Desktop PC ..........................15
Notebook PC ........................15
Video Source ........................15
DVD ......................................16
D-TV Set-Top Box ................16
Special Menu Options
Selecting Language ........................................20
Using ARC Function........................................20
Flip Horizontal Function ..................................20
Flip Vertical Function.......................................21
Using Keystone Function ................................21
LED Mode Function ........................................21
Altitude Mode Function ...................................21
Screen Menu Options
Auto Configure Function .................................22
Using Clock Function ......................................22
Using Phase Function.....................................22
Using Horizontal Function...............................23
Using Vertical Function ...................................23
Information
Supported Monitor Display..............................24
Maintenance....................................................24
Specifications ..................................................25
Function
Video Menu Options
Adjusting Video ...............................................17
APC (Auto Picture Control) .............................17
Auto Color Temperature Control .....................18
Gamma Function ............................................18
Black level Function ........................................19
Keypad Sound Function ..................................19
Keypad LED Function .....................................19
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is attached to a product it
means the product is covered by the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately
from the municipal waste stream via designated collection facilities
appointed by the government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential
negative consequences for the environment and human health.
4. For more detailed information about disposal of your old appliance,
please contact your city office, waste disposal service or the shop
where you purchased the product.
3
Safety Instructions
Safety Instructions
Please take note of the safety instructions to prevent any potential accident or misuse of the projector.
➟ Safety Instructions are given in two forms as detailed below.
WARNING : The violation of this instruction may cause serious injuries and even death.
NOTES : The violation of this instruction may cause light injuries or damage to the projector.
➟ After reading this manual, keep it in the place that the user always can contact easily.
Indoor Installation
Do not place the Projector in direct
sunlight or near heat sources such
as radiators, fires and stove etc.
This may cause a fire hazard !
WARNING
Do not place inflammable materials beside the projector
Do not allow children to hang on
the installed projector.
This may cause a fire hazard !
It may cause the projector to fall, causing injury or death.
Indoor Installation
Disconnect from the mains and
remove all connections before
moving.
NOTES
Do not place the projector close
to sources of steam or oil such
as a humidifier.
This may create a fire hazard or an
electric shock hazard !
When installing the projector on a
table, be careful not to place it
near the edge.
This may cause the projector to fall
causing serious injury to a child or
adult and serious damage to the
projector.
Only use a suitable stand.
Only use the projector on a level
and stable surface.
It may fall and cause injury and/or
damage to the unit.
Do not place the projector where
it might be exposed to dust.
This may cause a fire hazard or
damage to the unit!
Ensure good ventilation around the
projector. The distance between
the projector and the wall should
be more than 20cm/8 inches.
An excessive increase in its internal
temperature may cause a fire hazard or
damage to the unit!
Do not block the vents of the projector or restrict air-flow in any way.
Do not place the projector directly on a carpet, rug or place where
ventilation is restricted.
This would cause the internal temperature to increase and could cause a fire
hazard or damage to the unit!
This would cause its internal temperature to increase and might create a fire
hazard or damage the unit.
Outdoor Installation
WARNING
Do not use the projector in a damp place such as a bathroom where it is likely to get wet.
This may cause a fire or an electric shock hazard !
Power
Earth wire should be connected.
If the earth wire is not connected, there is a
possible danger of electric shock caused by
the current leakage.
If grounding methods are not possible, a
separate circuit breaker should be installed
by a qualified electrician.
Do not connect ground to telephone wires,
lightning rods or gas pipe.
4
WARNING
The mains plug should be inserted
fully into the power outlet to avoid a
fire hazard !
This may cause a fire hazard or damage
the unit.
Do not place heavy objects on
the power cord.
This may cause a fire or an electric
shock hazard !
Safety Instructions
Power
WARNING
Do not use too many plugs on the Mains multi-outlet.
It may result in overheating of the outlet and causes a fire hazard !
Power
Never touch the power plug with
a wet hand
This may cause an electric shock
hazard !
NOTES
Hold the plug firmly when unplugging. If you pull the cord, it may
be damaged.
Prevent dust collecting on the
power plug pins or outlet.
This may cause a fire hazard !
This may cause a fire hazard !
Do not plug when the power cord
or the plug is damaged or any
part of the power outlet is loose.
Ensure the power cord does not
come into contact with sharp or
hot objects such as a heater.
Place the projector where people
will not trip or tread on the power
lead.
This may cause a fire or an electric
shock hazard or damage to the unit!
This may cause a fire or an electric
shock hazard or damage to the unit!
This may cause a fire or an electric
shock hazard or damage to the unit!
Do not turn the projector On/Off by plugging-in or unplugging the power plug to the wall outlet.
(Do not use the power plug for switch.)
It may cause mechanical failure or could cause an electric shock.
Using
Do not place anything containing
liquid on top of the projector such
as flowerpot, cup, cosmetics or
candle.
This may cause a fire hazard or
damage to the unit!
WARNING
In case of impact shock or damage to the projector switch it off
and unplug it from the mains outlet and contact your service center.
Do not allow any objects to fall
into the projector.
This may cause an electric shock
hazard or damage to the unit!
This may cause a fire or an electric
shock hazard or damage to the unit!
If water is spilt into the projector unplug it from
the mains supply outlet immediately and consult
your Service Agent.
In the event that an image does not appear on the
screen please switch it off and unplug it from the
mains supply and contact your Service Agent.
This may cause an electric shock hazard or damage to
the unit!
This may cause a fire or an electric shock hazard or
damage to the unit!
Do not remove any covers
(except lens cover). High risk of
Electric Shock!
Don’t look directly onto the lens
when the projector is in use. Eye
damage may occur!
Do not touch metal parts during or
soon after operation since the
vents and lamp cover will remain
very hot!
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit; that is,a single outlet circuit which
powers only that appliance and has no additional outlets or branch circuits.Check the specification page
of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets,loose or damaged wall outlets, extension cords,
frayed power cords,or damaged or cracked wire insulation are dangerous.Any of these conditions could
result in electric shock or fire. Periodically examine the cord of your appliance,and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced
with an exact replacement part by an authorized service personnel.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched,
closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the
cord exits the appliance.
5
Safety Instructions
Using
WARNING
Never touch the wall outlet when
there is leakage of gas, open the
windows and ventilate.
It can cause a fire or a burn by a
spark.
Do not drop the projector or allow
impact shock.
Don’t look at laser beam directly
as it can cause eye damage!
This may cause mechanical failure or
personal injury !
Using
NOTES
Do not place heavy objects on
top of projector.
This may cause mechanical failure or
personal injury!
Take care not to impact the lens
particularly when moving the
projector.
Do not touch the lens of the projector. It is delicate and easily
damaged.
Do not use any sharp tools on the projector as this will damage the casing.
Cleaning
WARNING
Do not use water while cleaning
the projector
This may cause damage to the
projector or an electric shock hazard.
In the unlikely event of smoke or
a strange smell from the projector,
switch it off , unplug it from the
wall outlet and contact your
dealer or service centre.
Use an air spray or soft cloth that
is moist with a neutral detergent
and water for removing dust or
stains on the projection lens.
This may cause a fire or an electric
shock hazard or damage to the unit!
Cleaning
Contact the Service
Center once a year to
clean the internal
parts of the projector.
Accumulated dust can
cause mechanical failure.
NOTES
When cleaning the plastic parts such as projector case, unplug the power and
wipe it with a soft cloth. Do not use cleanser, spray water or wipe with a wet
cloth. Especially, never use cleanser (glass cleaner), automobile or industrial
shiner, abrasive or wax, benzene, alcohol etc., which can damage the
product. Use an air spray or soft cloth that is moist with a neutral detergent
and water for removing dust or stains on the projection lens.
It can cause fire, electric shock or product damage (deformation, corrosion and damage).
Others
WARNING
Do not attempt to service the projector yourself. Contact your dealer or service centre.
This may cause damage to the projector and could give an electric Shock as well as invalidating the warranty !
Others
NOTES
Be sure to unplug if the projector is not to be used for a long period.
Accumulated dust may cause a fire hazard or damage to the unit!
6
Names of parts
Names of parts
Main Body
* The projector is manufactured using high-precision technology. You may, however, see on the Projector
screen tiny black points and/or bright points (red, blue, or green). This can be a normal result of the
manufacturing process and does not always indicate a malfunction.
Focus ring
Control panel
Connecting Part
Kensington Security
System Connector
(Refer to page 13)
A/V IN
SVC Only
DIGITAL VIDEO
DC IN
RGB IN (PC/DTV)
* What is the DIGITAL VIDEO input?
This is the input terminal to receive and display the digital video signal from the HDMI jack.
7
Names of parts
Control Panel
SOURCE Button
Switches to RGB, Digital Video, Video mode.
SOURCE
A
OK Button
Checks present mode and
saves the change of functions.
POWER Button
MENU Button
Turn ON/OFF the projector.
Selects or closes menus.
/
/
/
Button
Adjusts functions of menus.
8
Names of parts
Accessories
Owner’s manual
CD Owner’s manual
Power Cord
Computer Cable
RGB to Component Cable
A/V Cable
Polishing Cloth
Adapter
Portable bag
Optional Extras
* Contact your dealer to purchase these items.
Projection Screen
HDMI Cable
Component Cable
9
Installing and Composition
Installing and Composition
Installation Instructions
* Don’t place the projector in the following conditions. It may cause malfunction or product damage.
Provide proper ventilation for this projector.
●The projector is equipped with ventilation holes(intake)
●Do not place the projector on a carpet, rug or other
on the bottom and ventilation holes(exhaust) on the front.
Do not block or place anything near these holes, or internal heat build-up may occur, causing picture degradation
or damage to the projector.
●Never push projector or spill any kind of liquid into the
similar surface. It may prevent a adequate ventilation
of the projector bottom. This product should be
mounted to a wall or ceiling only.
●Leave an adequate distance(30cm/12 inches or
projector.
more) around the projector.
In high altitude environments, set the mode to High Altitude mode before using the product.
● For locations over sea level of 1250m, it is recommended to use the High Altitude mode. (refer p.21)
Place this projector in adequate temperature and humidity conditions.
● Install this projector only in a location where adequate temperature and humidity is available. (refer p.25)
Don’t place the projector where it can be covered with dust.
● This may cause overheating of the projector.
Do not obstruct the slots and openings of the projector. This may cause overheating and create a fire
hazard.
The projector is manufactured using high-precision technology. You may, however, see tiny black points
and/or bright points (red, blue, or green) that continuously appear on the projector Screen. This is a normal result of the manufacturing process and does not indicate a malfunction.
To display DTV programs, it is necessary to purchase a DTV receiver (Set-top Box) and connect it to the
projector.
If there is no input signal, the Menu will not be displayed on screen.
10
Installing and Composition
How to install the projector using the tripod
* You can install this projector using a tripod for the camara. You can assemble the projector instead of the camera
on camera tripod.
Part connected to the projector
Part connected to the tripod
Bottom side of Projector
Camera Tripod
- If you have a camera tripod, assemble the projector to the part connecting to the camera tripod
Finished condition when projector is install on the tripod
11
Installing and Composition
Basic Operation of the Projector
1.Place the projector on a sturdy and horizontal surface with the PC or AV source.
2.Place the projector with the desired distance from the screen. The distance between the projector and the screen
determines the actual size of the image.
3.Position the projector so that the lens is set at a right angle to the screen. If the projector is not set at a right angle, the
screen image will be crooked. If this is so then the keystone adjustment may correct this (Refer to page 21.).
4.Connect the cables of the projector to a wall power socket and other connected sources.
projection distance based on the picture format
Screen
Projection off-set ratio:100%
X/2
Screen height (X)
X/2
Projection distance (D)
Y/2
Screen
Screen Width (Y)
43mm
Y/2
Projection distance (D)
4 : 3 Scale
Diagonal Size
(inch)
12
Diagonal Size
(mm)
Horizontal Size
(mm)
Vertical Size
(mm)
Projection Distance(D)
(mm)
Installing and Composition
Using Kensington Security System
● The projector has a ‘Kensington’ Security System Connector on the back panel. Connect the ‘Kensington’
Security System cable as below.
● For the detailed installation and use of the Kensington Security System, refer to the user’s guide attached
to the Kensington Security System set.
And for further information, contact http://www.kensington.com, the internet homepage of the
Kensington company that deals with expensive electronic equipment such as notebook PCs or projectors.
● Kensington Security System is an optional item.
13
Installing and Composition
Turning on the Projector
1. Connect power cord correctly.
2. Press the POWER button(
) on the Control panel. (The light on the control panel will be turned on.)
● Use the SOURCE button on the control panel to select the input signal you want.
● When you press the POWER button(
) on the control panel when you turn on the projector, the lights for all buttons on the control
panel will be turned on.
Turning off the Projector
1. Press the POWER button(
) on the Control panel.
2. Press the POWER button(
) on the Control panel again to turn off the power.
● When you press the POWER button(
) on the control panel when you turn off the projector, the lights for all the buttons on the control panel will be turned off. When you press any button on the control panel when the projector is turned
off, the light only on the POWER LED will be turned on. (When the Power cord is connected.)
Power off?
Please Press
Key Again.
Focus and Position of the Screen Image
When an image appears on the screen, check if it is in focus and fits well to the screen.
Focus ring
● To adjust the focus of the image, rotate the focus ring which is the outer ring on the lens.
Selecting source mode
1. Press the SOURCE button.
Select
F
OK
RGB
G
2. Each press of the F, G button changes the display as below.
RGB
Digital Video
Video
● When you connect the RGB to Component cable to the RGB IN (PC/DTV) terminal and select RGB input, you can receive the Component input.
● Digital video is the signal to receive and display the digital video signal through the HDMI jack.
14
Connection
Connection
Connecting to a Desktop PC
* You can connect the projector to a computer of VGA, SVGA, XGA and SXGA output.
* Refer to page 24 for the supported monitor displays of the projector.
< How to connect >
Connect computer cable to RGB IN (PC/DTV) of the projector.
Connecting to a Notebook PC
< How to connect >
Connect computer cable to RGB IN (PC/DTV) of the
projector.
* If you set your computer to output the signal to both the
display of your computer and the external projector, the
picture of the external projector may not appear properly.
In such cases, set the output mode of your computer to
output the signal only to the external projector. For
details, refer to the operating instructions supplied with
your computer.
Connecting to a Video Source
* You can connect a VTR, a camcorder or any other compatible video image source to the projector.
< How to connect >
a. Connect the A/V IN jack of the projector to the output jacks
of the A/V source with A/V cable.
<VCR>
S VIDEO
(R) AUDIO (L)
VIDEO
OUT
IN
15
Connection
Connecting to a DVD
* The output jacks (Y, PB, PR) of the DVD might be labelled as Y, Pb, Pr / Y, B-Y, R-Y / Y, Cb, Cr according to the equipment.
< How to connect >
RGB to Component Cable
a. After connecting the Component cable of DVD to the RGB to
Component cable, connect it to the RGB IN(PC/DTV) terminal of the projector.
Component cable
* When connecting the component cable, match the jack colors
with the component cable.(Y=green, PB=blue, PR=red)
(R) AUDIO (L)
b. You can set the Digital video mode olny when there is a
HDMI terminal in the DVD device.
Signal
Component
RGB/DTV
480i
O
X
X
480p
O
O
O
PB
Y
PR
<DVD>
HDMI/DVI
720p
O
O
O
1080i
O
O
O
576i
O
X
X
576p
O
O
O
Connecting to a D-TV Set-Top Box
* To receive D-TV programmes, it is necessary to purchase a D-TV receiver (Set-Top Box) and
connect it to the projector.
* Please refer to the owner's manual of the D-TV Set-Top Box for the connection between projector and
D-TV Set-Top Box.
< How to connect an RGB source >
a. Connect RGB cable to RGB IN (PC/DTV) of the
projector.
<D-TV Set-Top Box>
* When it is connected to the D-TV Set-top box with DVI output, you
can watch at the Digital Video mode by using the DVI to HDMI
cable.
(R) AUDIO (L)
HDMI OUTPUT
DTV OUTPUT
DVI OUTPUT
Y
PB
b. Use a DTV receiver with DTV 480p(576p)/720p/1080i mode.
HDMI cable
< How to connect a Digital Video source >
a. Connect the DIGITAL VIDEO terminal of the projector to the
HDMI output terminal of the D-TV Set-Top Box via HDMI
cable.
<D-TV Set-Top Box>
b. Use a DTV receiver with DTV 480p(576p)/720p/1080i mode.
< How to connect a Component source >
a. Connect the D-TV Set-Top Box Component cable with RGB
to Component cable and than connect it to RGB
IN(PC/DTV) of the projector.
* When connecting the component cable, match the jack colors
with the component cable.(Y=green, PB=blue, PR=red)
b. Use a DTV receiver with DTV 480p(576p)/720p/1080i mode.
16
(R) AUDIO (L)
HDMI OUTPUT
DTV OUTPUT
Y
DVI OUTPUT
RGB to Component Cable
Component cable
<D-TV Set-Top Box>
(R) AUDIO (L)
HDMI OUTPUT
DTV OUTPUT
DVI OUTPUT
Y
PB
PR
PB
PR
PR
Function
Function
* In this manual, the OSD(On Screen Display) may be different from your Projector’s because it is just an example to
help with the Projector operation.
* If there is no input signal present, the Menu will not be displayed.
* This operating guide explains operation of RGB(PC) mode mainly.
Video Menu Options
< RGB mode >
Adjusting Video
1. Press the MENU button(
the
menu.
) and then use F, G button to select
2. Press the D , E button to select a video item you want to adjust.
3. Press the F, G button to adjust the screen condition as you want.
●
●
●
●
Each adjustment of
menu options will not affect other inputs.
As required, re-adjust
menu options for the following input source :
Video/Component (480i(576i)), Component (480p(576p), 720p, 1080i)
To restore the original image condition after changing it, press A OK button
after selecting [Reset] item.
When receiving an NTSC signal, the picture item Tint is displayed and can
be adjusted.(60Hz only)
To exit the menu display, repeatedly press the MENU button(
).
Contrast
Brightness
Color R
Color G
Color B
Reset
50
50
50
50
50
MENU Exit
FG
Move
OK
< Video mode >
APC
Contrast
Brightness
Color
Sharpness
Tint
MENU Exit
F
G
Clear
80
50
50
70
0
FG
Move
OK
APC (Auto Picture Control)
* Use APC to set the projector for the best picture appearance.
* This function will not work at the RGB mode and the Digital video mode.
1. Press the MENU button(
the
menu.
2. Press the
) and then use F, G button to select
D , E button to select APC
item.
3. Press the F, G button to adjust the screen condition as you want.
●
●
MENU Prev.
Each press of the D, E button changes the screen as shown below.
Clear
Soft
APC
Contrast
Brightness
Color
Sharpness
Tint
F
Clear
G
80
50
50
70
0
D
E
Move
FG
Select
User
To exit the menu display, repeatedly press the MENU button(
).
17
Function
Auto Color Temperature Control
- To initialize values (reset to default settings), select the Normal option.
) button and then use F, G button to select
1. Press the MENU(
the
menu.
2. Press the
D , E button to select ACC
item.
3. Press the F, G button to make desired adjustments.
●
Each press of the
F, G
button changes the screen as shown below.
Normal
●
Cool
ACC
F
Normal
G
Gamma
Black Level
F
Film
G
F
High
G
Keypad Sound
F
On
G
Keypad LED
F
On
G
MENU Prev.
D
E
Move
FG
Select
Warm
To exit the menu display, repeatedly press the MENU button(
).
Gamma Function
1. Press the MENU button(
the
menu.
2. Press the
3. Press the
●
D , E button to select Gamma
F, G
18
item.
button to adjust the screen condition as required.
Each press of the D,
Normal
●
) and then use F, G button to select
E
button changes the screen as shown below.
Film
F
Normal
G
Gamma
F
Film
G
Black Level
F
High
G
Keypad Sound
F
On
G
Keypad LED
F
On
G
MENU Prev.
Sports
To exit the menu display, repeatedly press the MENU button(
ACC
).
D
E
Move
FG
Select
Function
Black level Function
1. Press the MENU button(
the
menu.
) and then use F, G button to select
2. Press the D , E button to select Black level item.
3. Press the F, G button to select Low or High.
This function works in the following mode : Digital Video
To exit the menu display, repeatedly press the MENU button(
).
● The menu is is activate/deactivate depending on the DVD setting status.
Black level function is activated only when the format is set to 4:4:4 or
4:2:2 among the set value of DVD device.
●
●
ACC
F
Normal
G
Gamma
F
Film
G
Black Level
F
High
G
Keypad Sound
F
On
G
Keypad LED
F
On
G
MENU Prev.
D
E
Move
FG
Select
* What is the Black level function?
When you watch the movie, this function adjusts the set to the best
picture appearance. Adjusting the contrast and the brightness of the
screen using the black level of the screen.
Keypad Sound Function
1. Press the MENU button(
the
menu.
) and then use F, G button to select
2. Press the D , E button to select Keypad Sound item.
3. Press the F, G button to select On or Off.
●
To exit the menu display, repeatedly press the MENU button(
).
ACC
F
Normal
G
Gamma
F
Film
G
Black Level
F
High
G
Keypad Sound
F
On
G
Keypad LED
F
On
G
D
E
MENU Prev.
Move
FG
Select
Keypad LED Function
1. Press the MENU button(
the
menu.
) and then use F, G button to select
2. Press the D , E button to select Keypad LED item.
3. Press the F, G button to select On or Off.
●
To exit the menu display, repeatedly press the MENU button(
).
ACC
F
Normal
G
Gamma
Black Level
F
Film
G
F
High
G
Keypad Sound
F
On
G
Keypad LED
F
On
G
MENU Prev.
D
E
Move
FG
Select
19
Function
Special Menu Options
Selecting Language
1. Press the MENU button(
the
menu.
2. Press the
) and then use F, G button to select
D , E button to select Language
item.
Language
F
English
G
ARC
F
4:3
G
Flip Horizontal
3. Press the
F, G
button to select the language you want to use.
Flip Vertical
On-Screen-Display (OSD) is displayed in the selected language.
● To exit the menu display, repeatedly press the MENU button(
).
●
MENU Prev.
D
E
Move
FG
Select
Using ARC Function
1. Press the MENU button(
the
menu.
2. Press the
) and then use F, G button to select
D , E button to select ARC
item.
Language
F
English
G
ARC
F
4:3
G
Flip Horizontal
3. Press the
F, G
button to select the screen size you want to use.
4:3
●
MENU Prev.
16 : 9
To exit the menu display, repeatedly press the MENU button(
Flip Vertical
D
E
Move
Select
FG
).
Flip Horizontal Function
* This function reverses the projected image horizontally.
Use this function when rear projecting an image.
1. Press the MENU button(
the
menu.
) and then use F, G button to select
Language
F
English
G
ARC
F
4:3
G
Flip Horizontal
2. Press the D , E button to select Flip Horizontal item.
3. Press the A OK button to see reversed image.
●
●
20
Each time you press the A OK button, the image will be reversed.
To exit the menu display, repeatedly press the MENU button(
).
to Flip
Flip Vertical
MENU Prev.
D
E
Move
OK
Function
Flip Vertical Function
* This function reverses the projected image vertically.
* When you hang the projector upside down from the ceiling ,
you will need to reverse the image vertically and horizontally.
1. Press the MENU button(
the
menu.
2. Press the
) and then use F, G button to select
D , E button to select Flip Vertical
item.
Language
F
English
G
ARC
F
4:3
G
Flip Horizontal
3. Press the A OK button to see reversed image.
●
●
to Flip
Flip Vertical
Each time you press the A OK button, the image will be reversed.
To exit the menu display, repeatedly press the MENU button(
).
D
E
MENU Prev.
Move
OK
Using Keystone Function
* Use this function when the screen is not at a right angle to the projector and the image is a trapezoid shape.
* Only use the Keystone function when you can’t get the best angle of projection.
1. Press the MENU button(
the
menu.
) and then use F, G button to select
Keystone
2. Press the D , E button to select Keystone item.
3. Press the F, G button to make desired adjustments.
0
LED Mode
F
Normal
G
Altitude Mode
F
Normal
G
D
E
MENU Prev.
●
Keystone can be adjusted from -50 to +50.
●
To exit the menu display, repeatedly press the MENU button(
Move
FG
Adjust
).
LED Mode Function
1. Press the MENU button(
the
menu.
2. Press the
) and then use F, G button to select
Keystone
D , E button to select LED Mode
item.
3. Press the F, G button to select Normal or Dark.
●
To exit the menu display, repeatedly press the MENU button(
0
LED Mode
F
Normal
G
Altitude Mode
F
Normal
G
D
E
MENU Prev.
).
Move
FG
Select
Altitude Mode Function
1. Press the MENU button(
the
menu.
2. Press the
) and then use F, G button to select
D , E button to select Altitude Mode
item.
3. Press the F, G button to select Normal or High.
For locations over sea level of 1250m, it is recommended to use the
High Altitude Mode.
● When you use the projector in High Altitude Mode, the fan speed
becomes faster to increase the perfomance of the cooling system,
which can increase the noise level.
● To exit the menu display, repeatedly press the MENU button(
).
●
Keystone
0
LED Mode
F
Normal
G
Altitude Mode
F
Normal
G
MENU Prev.
D
E
Move
FG
Select
21
Function
Screen Menu Options
Auto Configure Function
* This function assures you of getting the best video quality by automatically adjusting the horizontal size and synchronization
of the image.
* Auto Tracking function works in RGB PC input only.
1. Press the MENU button(
the
menu.
) and then use
F, G
button to select
2. Press the
D,E
button to select Auto configure item.
3. Press the
A OK
button.
●
Press OK to start
0
4
0
0
Auto configure
Clock
Phase
Horizontal
Vertical
Image positioning and synchronization are automatically adjusted.
MENU Store
D
E
Move
OK
4. If any more manual adjustement is needed according to the various PC mode inputs even after the auto-correction, execute
Clock, Phase, Horizontal and Vertical function in
menu.
In certain circumstances, you can’t get the best picture quality by
only using auto-correction.
●
To exit the menu display, repeatedly press the MENU button(
).
Using Clock Function
1. Press the MENU button(
the
menu.
2. Press the
D,E
3. Press the
F, G
F, G
) and then use
button to select
button to select Clock item.
button to make desired adjustments.
●
Clock adjustment range is -25 ~ +25.
●
To exit the menu display, repeatedly press the MENU button(
).
The variable range can be different depends on input resolutions.
●
Auto configure
Clock
Phase
Horizontal
Vertical
MENU Prev.
0
4
0
0
D
E
Move
FG
Adjust
FG
Adjust
Using Phase Function
1. Press the MENU button(
the
menu.
2. Press the
D,E
3. Press the
F, G
F, G
button to select
button to select Phase item.
button to make desired adjustments.
●
Phase adjustment range is 0 ~ 31.
●
To exit the menu display, repeatedly press the MENU button(
).
The variable range can be different depends on input resolutions.
●
22
) and then use
Auto configure
Clock
Phase
Horizontal
Vertical
MENU Prev.
0
4
0
0
D
E
Move
Function
Using Horizontal Function
1. Press the MENU button(
the
menu.
) and then use
D,E
button to select
2. Press the
D,E
button to select Horizontal item.
3. Press the
F, G
button to make desired adjustments.
●
Horizontal adjustment range is -50 ~ +50.
●
To exit the menu display, repeatedly press the MENU button(
).
The variable range can be different depends on input resolutions.
●
Auto configure
Clock
Phase
Horizontal
Vertical
MENU Prev.
0
4
0
0
D
E
Move
FG
Adjust
FG
Adjust
Using Vertical Function
1. Press the MENU button(
the
menu.
) and then use
D,E
button to select
2. Press the
D,E
button to select Vertical item.
3. Press the
F, G
button to make desired adjustments.
●
Vertical adjustment range is -50 ~ +50.
●
To exit the menu display, repeatedly press the MENU button(
).
The variable range can be different depends on input resolutions.
●
Auto configure
Clock
Phase
Horizontal
Vertical
MENU Prev.
0
4
0
0
D
E
Move
23
Information
Supported Monitor Display
* The following table lists the display formats supported by the projector.
Sources
Format
Vertical Freq.(Hz)
Horizontal Freq.(kHz)
* If the projector does not support the input signal, “Out of Range” message appears on the screen.
* The projector supports DDC1/2B type as Plug & Play function. (Auto recognition of PC monitor)
* The Synchronization input form for horizontal and vertical frequencies are Separate.
* According to PC, the optimum vertical frequency may not be displayed up to the optimum frequency of set in ‘Registration information (Display
registration information)’. (ex, The optimum vertical frequency may be displayed up to 85Hz or under in the resolution of 640X480 or 800X600.)
* In case of the use of HDMI to HDMI cable, PC shall not be supported.
<DVD/DTV Input>
Signal
NTSC(60Hz)
PAL(50Hz)
Component-*1 RGB(DTV)-*2
HDMI(DTV)-*3
480i
O
X
X
480p
O
O
O
720p
O
O
O
1080i
O
O
O
576i
O
X
X
576p
O
O
O
720p
O
O
O
1080i
O
O
O
* Cable type
1- RGB to Component Cable
2- Computer Cable
3- HDMI Cable
* Recomended 720p for a better image.
Maintenance
* The projector needs little maintenance. You should keep the lens clean because any dirt or stains may appear on the screen. If any parts need to be
replaced, contact your dealer. When cleaning any part of the projector, always turn the power off and unplug the projector first.
Cleaning the lens
If there is any dust or stain on the surface of the lens, you must always clean the lens. Use an air sapray or cleaning cloth for product exterior, provided with the product, to lightly clean the product. When you want to remove dust or stain on the lens, use the air spray or choth for product exterior, provided with the product, with neutral detergent and water.
Cleaning the Projector Case
To clean the projector case, first unplug the power cable. To remove dirt or dust, wipe the casing with polish cloth provided. When you want to remove
the dust or stain on the lens, use the cloth for product exterior, provided with the product.
Do not use alcohol, benzene, thinners or other chemical detergents as these can cause the casing to be warped or discolored.
24
Information
Specifications
MODEL
HS101 (HS101-JE)
Resolution
800(Horizontal) x 600(Vertical)pixel
Horizontal / Vertical Ratio
4:3(horizontal:vertical)
DLP panel size
0.55 inches
Screen size
(Projection distance)
0.40 ~ 2.23m(15 ~ 80 inches)
Projection OFF SET
100%
Video compatibility
NTSC/PAL/SECAM/NTSC4.43/PAL-M/PAL-N
Power
19V
, 4.74A
AC-DC Adapter
Lite-on, PA-1900-08
Height(mm/inches)
50/2.0
Breadth(mm/inches)
154/6.1
Length(mm/inches)
117/4.6
Weight(g/pound)
750/1.65
Operating Condition
Temperature
In operation : 32~95°F(0°C~35°C)
In storage and transit : -4~140°F(-20°C~60°C)
Humidity
In operation : 0~ 75% relative humidity by dry hygrometer
Not in operation : 0 ~ 85% relative humidity by dry hygrometer
25
Model number
Serial number
:
:
LG DLP PROJECTOR
Please read this manual carefully before operating
your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the bottom of the set and
quote this information to your dealer when you
require service.
HS101
OWNER’S MANUAL