LG RAVENNA RDV3340 User's Manual

INSTALLATION AND OPERATION MANUAL
Direct-Vent Gas
Fireplace Inserts
The Ravenna™ fireplace insert is factory equipped for 40,000 BTU
input and can be converted to 33,000 using the smaller orifice provided.
Retain These Instructions For Future Reference
P/N 775,218M Rev. B, 12/2007
A French manual is available upon request. Order P/N 775,218CF. Ce manuel d’installation
est disponible en francais, simplement en faire la demande. Numéro de la pièce 775,218CF.
Shown with Cast Pillar face
In the Commonwealth of Massachusetts:
• Installation must be performed by a licensed plumber or gas fitter
• See Table of Contents for location of additional Commonwealth
of Massachusetts requirements
US
Report No. 050-S-15c-5
Ravenna™ 33/40 (RDV33/40)
WARNINGS
• Hot! Do not touch! The glass and surfaces of this appliance will be hot during operation and will
retain heat for a while after shutting off the appliance. Severe burns may result.
• Carefully supervise children in the same room as appliance.
• Suitable for installation into masonry or factory built fireplaces. These appliances may be installed in an aftermarket permanently located, manufactured (mobile) home (USA only), where not prohibited by local codes. This
appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible
for use with other gases unless a certified kit is used.
• Lennox™ gas-burning appliances are designed for use as a supplemental heater. They are not intended for
continuous use as a primary heat source.
WARNING: If the information in this manual is not
followed exactly, a fire or explosion may result
causing property damage, personal injury or loss
of life.
AVERTISSEMENT: Assurez-vous de bien suivre les instructions données dans cette notice pour réduire au minimum
le risque d’incendie ou d’explosion ou pour éviter tout
dommage matériel, toute blessure ou la mort.
Do not store or use gasoline or other flammable
vapors or liquids in the vicinity of this or any other
appliance.
POUR VOTRE SÉCURITÉ: Ne pas entreposer ni utiliser d'essence
ni d'autres vapeurs ou liquides inflammables à proximité de
cet appareil ou de tout autre appareil.
POUR VOTRE SÉCURITÉ: Que faire si vous sentez une odeur
de gaz:
• Ne pas tenter d'allumer d'appareil.
• Ne touchez à aucun interrupteur.
• Ne pas vous servir des téléphones se trouvant dans le bâtiment
• Appelez immédiatement votre fournisseur de gaz depuis un
voisin. Suivez les instructions du fournisseur.
• Si vous ne pouvez rejoindre le fournisseur de gaz, appelez
le service des incendies.
L'installation et l'entretien doivent être assurés par un
installateur ou un service d'entretien qualifié ou par le
fournisseur de gaz.
WHAT TO DO IF YOU SMELL GAS:
•
•
•
Do not light any appliance.
Do not touch any electrical switch; do not
Use any phone in your building.
Immediately call your gas supplier from a
neighbor’s phone. Follow your gas supplier's
instructions.
• If your gas supplier cannot be reached, call
the fire department.
Installation and service must be performed by a qualified installer, service agency or the gas supplier.
Cautions & Safety

FOR
YOUR SAFETY do not install or operate your
Ravenna™ gas insert without first reading & understanding this manual. Any installation or operation of
the appliance deviating from that which is stated in this
manual WILL void the warranty & may be hazardous.
INSTALLATION & REPAIR SHOULD ONLY BE DONE BY
A QUALIFIED SERVICE TECHNICIAN. DO NOT ATTEMPT
TO SERVICE THE APPLIANCE YOURSELF.
The insert should be inspected & cleaned before use
& at least annually by a qualified service technician.
More frequent cleaning may be required due to excessive lint from bedding material, carpeting, etc.
It is imperative that control compartments, burners, &
circulating air passageways of the room heater be kept
clean.
Adequate clearances around the combustion chamber
and accessibility clearances for servicing & proper
operation must be maintained.
Turn off the gas before servicing this appliance. It is recommended that a qualified service technician perform an appliance check-up at the beginning of each
heating season.
All installations must conform with all local, state,
& national codes. In the absence of local codes, the
installation must conform with National Fuel Gas Code
ANSI Z223.1-latest edition, also known as NFPA 54 (In
Canada, the current CAN/CSA B149.1 installation code).
Refer to the National Fuel Gas Code & local zoning &
code authorities for details on installation requirements.
Your Ravenna gas insert must be vented to the outside
in accordance with the latest edition of the National
Fuel Gas Code.
This gas insert MUST be vented directly to the outside
& MUST NEVER be attached to a chimney serving a
separate solid fuel burning appliance. Each gas appliance MUST USE a separate vent system. Common vent
systems are PROHIBITED.
Mobile home installations must conform with the Mobile
Home Construction and Safety Standard, Title 24 CFR,
Part 3280 (in Canada CAN/CSA Z240 MH), or, when such
a standard is not applicable, the Standard for Mobile
Home Installations, ANSI A225.1 - latest edition.
The appliance, when installed, must be electrically
grounded in accordance with local codes or in the absence of local codes, with the National Electrical Code,
ANSI/NFPA 70 - latest edition. In Canada, the current
CSA C22-1 Canadian Electrical Code - latest edition.
Do not make any make-shift compromises during installation. Any modification or alteration may result
in damage to the appliance or dwelling and will void
the warranty, certification and listings of this unit.

Failure
to use manufacturer provided parts, variations
in techniques and construction materials or practices
other than those described in this manual may create
a fire hazard and void the limited warranty.

Your Lennox™ gas insert must be equipped for the
proper fuel type & altitude at which it will be operated.
Any operation outside the parameters outlined in this
manual may result in a hazardous condition & will void
the warranty. Please carefully read the sections pertaining to these subjects and/or be sure your appliance is
properly equipped.
Do not use this insert if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance & to replace any part of the control system
& any gas control which has been under water.
Due to high temperatures, the insert should be located
out of traffic areas & away from furniture & draperies.
Children & adults should be alerted to the hazards of
high surface temperature & should stay away to avoid
burns or clothing ignition. Young children should be
carefully supervised when they are in the same room as
the Lennox gas insert. Clothing or any other flammable
material should not be placed on or near the insert.
Never use solid fuels such as wood, paper, cardboard,
coal, or any flammable liquids, etc., in this appliance.

Any grill, panel, or glass removed for service MUST be
replaced prior to operating the insert. Do not operate
appliance with the glass front removed, cracked or
broken. Replacement of the glass should be done by a
qualified service technician.
DO NOT USE abrasive cleaner on the glass door assembly. DO NOT ATTEMPT to clean the glass door when it
is hot.
Gold & nickel plated surfaces must be cleaned with
glass cleaner & a clean soft cloth before firing the first
time or fingerprints will remain permanently. NEVER use
brass polish to clean gold or nickel, this will remove
the plating!!!
When opening the lower door on the face while the
insert is burning, pull at the far left or far right vent
openings, because the door is hot during operation.
Lennox Hearth Products, its employees, or any of its
representatives assume no responsibility for any damages caused by an inoperable, inadequate, or unsafe
condition as a result of any improper operation, service
or installation procedures, whether direct or indirect.
INSTALLER: THESE INSTRUCTIONS ARE TO REMAIN
WITH THE HOME OWNER!
Table of Contents
Cautions & Safety...................................................................................... 2
Orifice Size / Altitude Adjustment..................................................................... 4
Fireplace Requirements................................................................................. 4
Codes & Approvals..................................................................................... 4
New York City, New York (MEA)................................................................. 5
Requirements For The Commonwealth of Massachusetts......................................... 5
Pre-Installation.......................................................................................6-8
Features............................................................................................. 6
Packaging List...................................................................................... 6
Ratings.............................................................................................. 6
Insert & Fireplace Dimensions..................................................................... 7
Clearances to Combustibles........................................................................ 8
Insert Leveling...................................................................................... 8
Installation.......................................................................................... 9-11
Venting Installation................................................................................ 9
Zero Clearance Fireplace Installation............................................................10
Brick Panel & Log Set Installation...............................................................10
Surround Panels Installation.....................................................................11
Face Installation...................................................................................11
Gas Line Installation...................................................................................12
Gas Pressure Requirements.......................................................................12
LP & Natural Gas Supplies.......................................................................12
Air Shutter Adjustment...........................................................................12-13
Operating Instructions.............................................................................13-16
Pre-Lighting Checklist............................................................................13
Lighting Instructions..............................................................................13
Flame Color & Behavior. .........................................................................15
Paint Curing.......................................................................................15
Quiet Operation....................................................................................15
Blower Operation..................................................................................15
Optional Wall Thermostat........................................................................15
Operating Options.................................................................................16
Millivolt Control System.........................................................................16
Maintenance & Servicing..........................................................................17-18
Maintenance Checklist.............................................................................17
Glass Maintenance.................................................................................17
Door Removal......................................................................................18
Fuel Conversion...................................................................................18
Blower Removal...................................................................................18
Troubleshooting........................................................................................19
Replacement Parts.....................................................................................20
Accessories.........................................................................................20-21
Insert Labels.......................................................................................22-23
Product Reference Information. ......................................................................24
Orifice Size/Altitude Adjustment
For altitudes above 2,000 feet (In Canada 4,500 FT/1370
M),the orifice should be de-rated by 4% for every 1,000 feet
to maintain the proper ratio of gas to air. Improper orifice
sizing may result in damage and unsafe conditions. Changing the orifice should only be done by a qualified service
technician. Contact your Lennox Hearth Products dealer for
proper orifice sizes.
IMPORTANT: When installing these appliances into a factory built fireplace or heat-form, the air flow within and
around the fireplace shall not be altered by the installation
of the insert (i.e. DO NOT BLOCK louvers or cooling air
inlet or outlet ports, circulating air chambers in a steel
fireplace liner or metal heat circulator).
WARNING
The Ravenna™ Insert
• Must conform with all local, state, and national installation
codes. In the absence of local codes, the installation must
conform with National Fuel Gas Code ANSI Z223.1 - latest
edition, also known as NFPA 54 (In Canada, the current
CAN/CSA B149.1 installation code). Refer to the National
Fuel Gas Code and local zoning and code authorities for
details on installation requirements.
• Mobile home installations must conform with the Mobile
Home Construction and Safety Standard, Title 24 CFR,
Part 3280 (in Canada CAN/CSA Z240 MH), or, when such a
standard is not applicable, the Standard for Mobile Home
Installations, ANSI A225.1 - latest edition.
• Must be vented directly to the outside in accordance with
the latest edition of the National Fuel Gas Code and must
never be attached to a chimney serving a separate solid
fuel burning appliance.
• Has been certified for use with either natural gas or propane.
• Is not for use with solid fuels.
• Is approved for sitting rooms and/or bedrooms.
Fireplace Requirements
These heaters are designed to be installed into an existing
masonry fireplace (built to UBC 37 or ULC S628 standards)
or factory built solid fuel, wood burning fireplace (listed to
UL 127 or ULC S610) only. All exhaust gases must be vented
outside the structure. Combustion air is drawn from outside
the structure. When installing in a factory built fireplace, the
fireplace grate must be removed and the damper must be
removed or secured open.
If the factory-built fireplace has no gas access hole(s)
provided, an access hole of 1-1/2 inches (38 mm) or less
may be drilled through the lower sides or bottom of the
firebox in a proper workmanship like manner. This access
hole must be plugged with a non-combustible insulation
after the gas supply line has been installed. The installer
must mechanically attach the marking supplied with the gas
fireplace insert to the inside of the firebox of the fireplace
into which the gas fireplace insert is installed.
THIS FIREPLACE HAS BEEN ALTERED TO
ACCOMMODATE A FIREPLACE INSERT AND
SHOULD BE INSPECTED BY A QUALIFIED
PERSON PRIOR TO RE-USE AS A
CONVENTIONAL FIREPLACE.
Smoke Detectors
Since there are always several potential sources of fire in
any home, we recommend installing smoke detectors. If
possible, install the smoke detector in a hallway adjacent
to the room (to reduce the possibility of occasional false
activation from the heat produced by the appliance). If your
local code requires a smoke detector be installed within
the same room, you must follow the requirements of your
local code. Check with your local building department for
requirements in your area.
Codes & Approvals
Certification
Gas appliances must be tested and certified by a nationally recognized testing and certification laboratory to ANSI
(American National Standard Institute) gas appliance safety
standards.
This insert has been tested and certified by OMNI -Test
Laboratories to ANSI Z21.88-2005/CSA 2.33-2005 Standard
for Vented Gas Fireplace Heater and CGA 2.17-M91 and UL
307B Gas Burning Heating Appliances for Manufactured
(Mobile) Homes in both USA and Canada.
It has met all necessary ANSI Standards and is fully certified
for installation in any community. If there are any questions
or if you need further substantiation either write to or call
your Lennox Hearth Products dealer. If you have further
questions, please contact Lennox Hearth Products.
Check all local building and safety codes before installation.
The installation instructions and appropriate code requirements must be followed exactly and without compromise.
In the absence of local codes the following standards and
codes must be followed.
New York City, New York (MEA)
Inspection
Installation of these fireplaces are approved for installation in New York
City in the US state of New York (MEA#: 138-07-E).
The state or local gas inspector of the side wall horizontally vented gas
fueled equipment shall not approve the installation unless, upon inspection,
the inspector observes carbon monoxide detectors and signage installed
in accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4.
Commonwealth Of Massachusetts
Requirements
Note: The following requirements reference various Massachusetts
and national codes not contained in this document.
Exemptions
The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
• The equipment listed in Chapter 10 entitled “Equipment Not Required
To Be Vented” in the most current edition of ANSI Z233.1 / NFPA 54 (In Canada CAN/CSA B149.1 - current edition) as adopted by the
Board; and
For all side wall horizontally vented gas fueled equipment installed in every
dwelling, building or structure used in whole or in part for residential
purposes, including those owned or operated by the Commonwealth and
where the side wall exhaust vent termination is less than seven (7) feet
above finished grade in the area of the venting, including but not limited
to decks and porches, the following requirements shall be satisfied:
• Product Approved side wall horizontally vented gas fueled equipment
installed in a room or structure separate from the dwelling, building
or structure used in whole or in part for residential purposes.
Installation Of Carbon Monoxide Detectors
MANUFACTURER REQUIREMENTS
At the time of installation of the side wall horizontal vented gas fueled
equipment, the installing plumber or gas-fitter shall observe that a hard
wired carbon monoxide detector with an alarm and battery back-up is
installed on the floor level where the gas equipment is to be installed.
In addition, the installing plumber or gas-fitter shall observe that a battery operated or hard wired carbon monoxide detector with an alarm is
installed on each additional level of the dwelling, building or structure
served by the side wall horizontal vented gas fueled equipment. It shall
be the responsibility of the property owner to secure the services of
qualified licensed professionals for the installation of hard wired carbon
monoxide detectors.
In the event that the side wall horizontally vented gas fueled equipment
is installed in a crawl space or an attic, the hard wired carbon monoxide
detector with alarm and battery back-up may be installed on the next
adjacent floor level.
In the event that the requirements of this subdivision can not be met
at the time of completion of installation, the owner shall have a period
of thirty (30) days to comply with the above requirements; provided,
however, that during said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
Approved Carbon Monoxide Detectors
Each carbon monoxide detector as required in accordance with the
above provisions shall comply with NFPA 720 and be ANSI/UL 2034
listed and IAS certified.
Signage
A metal or plastic identification plate shall be permanently mounted to
the exterior of the building at a minimum height of eight (8) feet above
grade directly in line with the exhaust vent terminal for the horizontally
vented gas fueled heating appliance or equipment. The sign shall read, in
print size no less than one-half (1/2) inch in size, “GAS VENT DIRECTLY
BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS.”
Gas Equipment Venting System Provided
When the manufacturer of Product Approved side wall horizontally vented
gas equipment provides a venting system design or venting system components with the equipment, the instructions provided by the manufacturer
for installation of the equipment and the venting system shall include:
• Detailed instructions for the installation of the venting system design
or the venting system components; and
• A complete parts list for the venting system design or venting system.
Gas Equipment Venting System NOT Provided
When the manufacturer of a Product Approved side wall horizontally
vented gas fueled equipment does not provide the parts for venting the
flue gases, but identifies “special venting systems”, the following requirements shall be satisfied by the manufacturer:
• The referenced “special venting system” instructions shall be included
with the appliance or equipment installation instructions; and
• The “special venting systems” shall be Product Approved by the
Board, and the instructions for that system shall include a parts list
and detailed installation instructions.
A copy of all installation instructions for all Product Approved side wall
horizontally vented gas fueled equipment, all venting instructions, all
parts lists for venting instructions, and/or all venting design instructions
shall remain with the appliance or equipment at the completion of the
installation.
• Installation and repair must be done by a plumber or gas fitter licensed
in the Commonwealth of Massachusetts.
• The flexible gas line connector used shall not exceed 36 inches (92
centimeters) in length.
• The individual manual shut-off must be a T-handle type valve.
Pre-Installation
Packaging List
Features
To install a Ravenna™ insert, an insert body, face, surround
(flange) kit, and brick panel are required.
Installation Options
Manufactured (Mobile) Home
Natural Gas Or Propane (LP)
Bedrooms
Optional Wall-mounted Or Remote Thermostat
Electrical
The standard fan motor requires 120 Volts AC for operation.
The fireplace is not dependent on the fan or an outside electrical supply to operate. WARNING - Electrical Grounding
Instructions - This appliance is equipped with a three-prong
(grounding) plug for your protection against shock hazard
and should be plugged directly into a properly grounded
three-prong receptacle. Do not cut or remove the grounding prong from this plug.
Millivolt Valve
This insert is operated with a millivolt valve and therefore
burns even during a power outage.
Fuel
This insert comes from the factory equipped to burn natural
gas at a specified elevation. The insert can be converted
to burn LP (liquid propane) by installing a conversion kit.
Only Lennox Hearth Products conversion kits can be used
to convert from NG to LP or LP to NG. Contact your Lennox
Hearth Products dealer for details.
Insert Body Packaging List
1 Insert Body with Burner Cassette
1 Set of Refractory Brick Panels
1 Log Set
1 Ravenna 40
1 #36 Burner Orifce (to convert to Ravenna 33)
1 Bag of Embers
1 Fasteners: 6 slotted 1/4" truss screws
6 speed nuts
9 spring clips
3 plastic adhesive wire restraints
1 Installation and Operation Manual
Decorative Faces - One Required
Traditional
Arch inset
Foundry
Screen
Cast pillar
Surround Kits - One Required
Traditional 1-pc. (41"W x 29"H)
Traditional 3-pc.(41"W x 29"H, 48"W x 29"H, 41"W x
33"H or 48"W x 33"H)
Cast Iron (45-1/2"W x 30"H-Cast Pillar face only)
Surround Kit Contents
1 Top Surround
2 Side Surrounds
3 Gold or Nickel Plated Trim Pieces
2 Elbowed Trim Fasteners
Ravenna 40 (RDV40)
RATINGS
Ravenna 33 (RDV33)
NATURAL GAS
LP GAS
NATURAL GAS
LP GAS
40,000/28,000
37,500/26,000
33,000/24,000
33,000/24,000
Manifold Pressure (IN. WC)
3.5
10.0
3.5
10.0
Min. Inlet Pressure (IN. WC)
5.0
10.5
5.0
10.5
Maximum heat output BTUs/hoursteady state (depending on vent
configuration)v
83%
83%
83%
83%
67.17%
69.07%
65.55%
67.80%
1/8”
#49
#36
#51
Max/Min Input BTUh 0-2,000 Feet
(0-610 M)u
P4 Efficiency
w
Orifice (DMS) 0-2,000 Feet (0-610
M)u
uUnit factory equipped for 0-2000 FT/0-610 M, In Canada 0-4500 FT/0-1370 M
vThe Steady State Efficiency numbers based on maximum vent configuration.
wTested to CSA P.4.1-02 “Testing Method for Measuring Annual Fireplace Efficiency.
Electrical Rating: 120 VAC, 60 HZ, Less Than 2 Amps
Insert Dimensions
Minimum Fireplace Cavity
31-1/4”
(794mm)
15-3/4"
(400mm)
13-3/4”
(349mm)
A
B
Top View
Figure 1
C
D
15-3/4"
(400mm)
Figure 3
CAUTIONS
19-1/2"
(495mm)
19-3/4
(502mm)
Figure 2
Side View
Insert Dimensions
Width of insert behind Surround Panels
Rear height
Insert depth into fireplace
Flue collar diameter (OD)2-15/16"
28" (711mm)
19-3/4" (502mm)
16" (406mm)
2-15/16" (75mm)
Minimum Fireplace Opening Required
A = 29-3/4” (756mm) Front Opening
B = 19-1/2” (495mm) Height
C = 19” (483mm) Rear Width
D = 16” (406mm) Fireplace Depth
* Top air duct will need to be removed for short ZC applications. Replace tap tights when removed.
• Trim panels or surrounds must not seal ventilation openings in the existing fireplace that the
appliance is installed in.
• The fireplace in which this gas insert is to be
installed must be thoroughly cleaned if it has
been used to burn wood or synthetic logs. Have
the chimney and all inside surfaces of the fireplace brushed and vacuumed so that no soot,
embers, or loose combustion deposits can be
drawn into the heat circulation blower and blown
into the living area.
• If any portion of the chimney system shows signs
of structural or mechanical weaknesses, such
as: cracks, leaky joints, corroded or warped
surfaces, the faulty portion must be repaired
or replaced prior to installing this appliance.
• The factory built firebox must accept the insert
without modification other than removing bolted
or screwed together pieces such as baffles /
smoke shelf / deflectors, ash lips, glass door,
screen or door tracks, log grates, refractory or
masonry lining and damper assemblies. Any
fireplace component, which is removed, must be
retained so they can be reinstalled to restore the
fireplace to its original operating condition. The
removal of any part must not alter the integrity
of the outer shell of the pre-engineered fireplace
cabinet in any way. Any parts removed must be
replaceable. If any components are removed
from (or altered) from the existing fireplace,
a Warning Label (see Page 4) must be affixed
inside the fireplace firebox, so that it shall be
visible upon removal of the fireplace insert. Note:
RTV high temperature silicone is an approved
adhesive to affix the label.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Clearances to Combustibles
Facing and Mantel Clearances
IMPORTANT: If unit is converted to an RDV33 from an
RDV40, the clearances to combustibles can be reduced
as shown on this page.
WARNING: If this unit is ever converted back to an RDV40,
ensure that the clearances are correct for this model.
Please note that the RDV33 mantel clearances are 4" less than the RDV40
mantel clearances as shown in Figures 4A (RDV40) and 4B (RDV33).
3"/76mm
3"/76mm
3"/76mm
1-1/2”
38mm
Minimum Clearances to Combustibles
Minimum clearances include any projections such as
shelves, window sills, mantels, spacers/standoffs or
surfaces to combustible construction etc. above the appliance. Paint or lacquer used to finish the mantel must
be heat resistant in order to avoid discoloration.
The letters below, E through J, correspond to Figure 5
showing minimum clearances required from the appliance
to combustibles and the minimum projection of the hearth
extension.
E = From Top Facing or Mantel to Bottom of Insert .2 RDV40 = 35-1/2”(902mm) and RDV33 = 311/2”(800mm)
35-1/2”
902mm
3"/76mm
3"/76mm
3"/76mm
1-1/2”
38mm
J = 10.5” (267mm) Mantel to Bottom of Insert .2 RDV40 = 43”(1092mm) and RDV33 = 39”(991mm)
G = Minimum Hearth Protection from Front of Insert*
H = Vertical Distance from Insert Bottom to Combustible
Material.
G
14”(356mm)
10”(254mm)
0”(0mm)
H
0”(0mm)
2”(21mm)
4”(102mm)
G
13”(330mm)
10”(254mm)
0”(0mm)
H
0”(0mm)
2”(21mm)
4”(102mm)
31-1/2”
800mm
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
36-1/2”
927mm
Mantel
MANTEL
Trim
TRIM
F
J
E
CL
Insert Leveling
At each front and rear corner of the insert is an adjustable leg
provided to level the insert should the hearth of the fireplace
be uneven. To adjust the legs, loosen the two 5/32" allen head
screws, move the leg to the desired height, and then tighten
the screws. Repeat these steps for each adjusting leg.
RDV33
Facing &
Mantel Side View
Figure 4B
Note: Hearth protection to be min. 3/8” (10mm) thick noncombustible or equivalent, with a k factor of .84.
39-1/2”
1003mm
33-1/2”
851mm
Hearth Protection
RDV33
40-1/2”
1029mm
Figure 4A
F = 25-1/2" From Center of Glass Door to Side Facing or
Wall - RDV40 = 25.5”(648mm) and RDV33 = 25.5”
(648mm)
RDV40
43-1/2”
1105mm
37-1/2”
953mm
RDV40
Facing &
Mantel Side View
H
G
Hearth / Floor Protection
Figure 5 - Clearances
Installation
The existing fireplace chimneys may take
various contours which the flexible liners will
accommodate. However, keep the flexible liner
as STRAIGHT as possible, avoid unnecessary
bending.
Venting Installation
Your Lennox™ gas insert must be vented to the outside
in accordance with the current edition of the National Fuel
Gas Code ANSI-Z223.1 (In Canada, the current CAN/CSA B149.1 installation code). The insert must not be connected
to a chimney flue serving a separate solid fuel burning appliance.
This gas insert requires a 3” diameter listed flex liner. The
vent should terminate with a listed direct vent termination
cap. The chimney should be sealed around the cap to prevent air and rain from entering the chimney. Adhere to the
vent manufacturer's instructions for installation and vent
termination. These appliances are approved for use with
the following vent kits.
The standard cap
in Termination Kit,
H0908, is a high
wind cap
Vertical Cap
Termination
Connector
Liner Requirements:
Use 3" (76 mm) diameter listed gas
vent liner (UL1777 ONLY) for the
EXHAUST
Use 3" (76 mm) diameter listed
liner (UL 181 or UL1777) for the
AIR INTAKE.
Exhaust
Vent Kits *
Cat. No.
Model
Description
H0909
FKDVI
Flex Liner Kit, DVI 3” X 35’
(requires 2, one for exhaust, and one for intake)
H0908
TKDVI
Termination Kit, DVI
(termination cap and flashing)
Vertical Venting
The vent pipes must be connected to the proper collars on
the unit and the exhaust vent pipe must be connected to the
termination cap or the unit will not operate. The combustion
air vent pipe can be connected to the termination cap or it
can terminate inside the chimney.
The bottom opening of the chimney must be sealed around
the vent pipes if the combustion air vent is not connected
to the termination cap. Use unfaced fiberglass insulation to
seal around the vent pipes. The insulation may give off an
odor during the first hour of operation.
NOTE: The minimum vertical rise (exhaust vent) is 10 feet
(3.1 M) and the maximum vertical rise is 35 feet (10.7 M).
These dimensions are measured from the starting collars
of the unit to the end of the vent pipe.
The fireplace and fireplace chimney must be clean and in good
working order and constructed of non-combustible materials.
Inspect chimney cleanouts for proper fit and seal.
Vertical Height Min. = 10 ft. (3.1 M)
Vertical height Max. = 35 ft. (10.7 M)
Note: Measured from flue collar on
unit to the end of the vent pipe or liner
Intake
The flexible vent pipe
must NOT be allowed to
sag behind insert or in
fireplace flue.
Combustion Air Intake
Figure 6
Make sure that both liners will pass through existing damper area. Remove
or lock damper to allow the passage of the flexible liners. If the damper
will not allow the passage of both liners, DO NOT PROCEED FURTHER.
(If fireplace is masonry) Consult a local mason for removal of the damper
without risk of structural damage or leakage (if the fireplace is factory
built) The appliance may NOT be installed into the fireplace.
WARNING
Direct-Vent Fireplace Insert Vent Requirements - Use liner
listed to UL181 (Factory-made Air Ducts And Air Connectors) or UL1777 (Chimney Liners) for the AIR INTAKE. Use
liner listed to UL1777 ONLY for the EXHAUST.
Do not substitute the heat-rated flex liner (UL1777) for the
exhaust with any other type liner or a fire may result causing property damage, personal injury or loss of life.
* Other approved vent components include; Standard Simpson Dura-vent Co-linear
Chimney Liner Kit, Direct Vent Termination #991, Liner Termination Kit (includes
termination connector and flashing) #923GK & 3" x 35' Alum Flex #2280
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Zero Clearance Fireplace Installation
This insert may be installed in a masonry or factory built/zero
clearance (ZC) fireplace. When installing in a ZC fireplace,
the ZC grate must be removed and the ZC damper must be
removed or secured open. The ZC doors, screen, refractory
or masonry lining, baffles, and smoke shelf may be removed
if necessary to install the gas insert. However, do not cut or
alter the fireplace components. The removal of any parts to
facilitate installation must not alter the integrity of the inner or
outer shells of the fireplace cabinet. Any parts removed must
be replaceable if the insert is taken out of the fireplace or the
fireplace clearly marked with a paint stick that "This fireplace
has been altered and is no longer safe to operate."
The insert is designed to fit into a ZC fireplace with a minimum firebox height of 19-1/2" (495mm). To facilitate this
the hood will need to be removed and discarded (Note: the
screws should be replaced in the insert body).
2 Screws
Figure 7
If the factory-built fireplace has no gas access hole(s) provided, an access hole of 1-1/2" (37.5 mm) or less may be
drilled through the lower sides or bottom of the firebox in
a proper workmanship like manner. This access hole must
be plugged with a non-combustible insulation after the gas
supply line has been installed.
Rear log
The installer must mechanically attach the marking supplied
with the gas fireplace insert to the inside of the firebox of the
fireplace into which the gas fireplace insert is installed.
Retainer
Figure 8
Ravenna™ 40 Conversion To Ravenna 33
To convert to a Ravenna 33 gas insert, after step 1 remove
and replace the stock burner orifice with the #36 NG orifice
supplied in the installation manual bag. Pipe dope or other
approved gas line sealant will need to be applied before inserting into bulkhead. The foil sticker supplied, stating RDV33,
will need to be affixed over the model name RDV40 on the
serial number label (located in the control compartment).
2. Place the rear brick panel on the brackets and reinstall the
log rack with the rear log. IMPORTANT!!! SCREWS PASS
THROUGH THE LOG RACK AND THE BURNER PAN.
3. Install the side brick panels by sliding them into place.
Brick Panel & Log Set Installation
If logs are not installed according to the log installation
instructions, flame impingement and improper combustion
could occur and result in soot and/or excessive production of
carbon monoxide (CO), a colorless, odorless, toxic gas.
The size and position of the log set is critical to achieve a
safe, reliable and attractive flame pattern. Any attempt to
use a different log set in the fireplace will void the warranty
and will result in incomplete combustion, sooting, and poor
flame quality.
1. Remove the log rack (2 screws) and install the rear log
on the retainer.
10
Figure 9
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Side Brick Panels
4. Install a light layer of rockwool directly over the ports.
- A light layer will give a more constant rear flame.
- A heavy layer will give more glow, but will need to
be adjusted after light up.
Figure 10
5. Install front logs on retainer slots.
Figure 11
Front Logs
2. Install all surround panels and trim with the insert positioned in the fireplace, but a few inches in front of its
final location.
3. If an Arch face is to be installed on the insert, the sight
obstructor that comes with the face must be installed
prior to installing the surround panels. See the instructions included with the face for proper sight obstructor
installation.
4. Install the side surround panels by lining up the holes in
the tabs on the side surround panels in front of the holes
on the surround brackets. Next insert two slotted 1/4"
truss screws for each side surround panel and secure
loosely.
5. Fasten the top surround panel with the remaining two
truss screws. Tighten all six truss screws after adjusting
the surround panels to eliminate space between side and
top surround panels.
6. Assemble the surround trim by inserting the elbowed
retainer in the rectangular slot in the ends of the longest
piece of trim and secure by tightening the screw in the
retainer. Slide the mitred ends of the two side trim pieces
onto the elbowed retainer and secure by tightening the
retainer screw.
7. The fastened trim pieces should now be horseshoe shaped.
Slide the trim down over the surround panels so the edge
of the surround panel fits just behind the rounded edge
of the trim. 8. Install three spring clips (found in parts bag in firebox)
in each piece of trim by inserting them between the rear
of the surround and the channel of the trim. The spring
clips will push the trim tight to the surround.
6.Place embers around the perimeter of the rockwool.
IMPORTANT!!! Do not cover the ports with the embers.
7. Place top log on pin.
A
C
Spring Handle Latches
B
Door Mounting Plates
Top Log
Figure 13
Face Installation
Figure 12
Surround Installation
Ports
A number of different face finishes and styles are available
for your Ravenna gas insert. The Arch face comes with a
sight obstructor that must be installed prior to installing
the surround panels and face. Instructions for installing the
sight obstructor are included with the face. The faces come
with hooked brackets. To install the face, hang the hooked
brackets on the surround brackets (See C in Figure 13).
The Ravenna™ insert surrounds are made of heavy gage
steel for durability and, if desired, for the ease of making
an inside fit in the fireplace. See Packaging List for available sizes.
Note: Gold and nickel plated surfaces must be cleaned with
1. Remove the speed nuts (A in Figure 13) from the parts
glass cleaner and a soft clean cloth before firing the first time
bag and install (with the flat surface forward) on the six
or fingerprints and stains will remin permanently. NEVER
holes in the surround brackets - three on each side of the
use brass polish to clean gold or nickel surfaces, this will
insert (B in in Figure 13). A flat bladed screwdriver may
remove the plating!!!
help in installing the nuts.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
11
Gas Line Installation
After leveling, position the insert in the fireplace - holding
it about six inches out from its final location. Caution: Specific hearth requirements apply (see Clearances to Combustibles).
The Ravenna™ gas insert must be connected to the gas
line in accordance with local codes and/or the National Fuel
Gas Code, ANSI Z223.1 (In Canada, the current CAN/CSA B149.1 installation code). The insert comes with an 8" nipple
attached to the supply side of the gas valve. After connecting the gas line, all joints in the line and connections at the
valve should be checked for leaks before final positioning of
the unit. Conduct a gas leakage test of the appliance piping
and control system downstream of the shutoff valve in the
supply line to the appliance.
Inlet Pressure
Manifold Pressure
Desired
Minimum
Maximum
On Hi
Fire
On Lo
Fire
Natural
Gas
7" WC
5" WC
10.5" WC
3.5" WC 1.7" WC
LP Gas
11" WC
10.5" WC
13" WC
10" WC
5.4” WC
Robertshaw Millivolt Gas Valve
TH
TP
TP/TH
Figure 14
Inlet (Supply)
Pressure Tap
The Manifold
(Outlet) Tap
Gas Pressure Requirements
LP and Natural Gas Supplies
A MAJOR CAUSE OF OPERATING PROBLEMS WITH GAS
APPLIANCES IS IMPROPER GAS PRESSURE!
Your Ravenna gas insert is equipped from the factory for
use with natural gas only as specified on the Safety / Listing
label attached to the appliance. This appliance can only be
operated using propane gas (LP) if a certified fuel conversion kit provided by Lennox Hearth Products is installed by
a qualified service technician. The most important item to check during the initial
installation and the first thing to check when operating
problems occur is gas pressure! This appliance will
not function properly unless the required gas pressure
is supplied. See the table on this page for gas pressure
requirements.
Two pressure taps are provided on the insert's valve to
check gas pressures. The taps are located to the right of
the on/off/pilot knob (see Figure 14). The bottom tap is the
inlet (supply) pressure side. To check inlet pressure (with
the insert burning), insert a small phillips screwdriver into
the tap and turn a half turn counter-clockwise. Cover the
tap with the line from a manometer and check the pressure.
Close the tap gently but securely after completing the check.
The manifold (outlet) tap is above the inlet tap. To check
manifold pressure (with the insert burning at the high burn
setting) insert a small phillips screwdriver into the tap and
turn a half turn counter-clockwise. Cover the tap with the
line from the manometer and check the pressure. Again,
close the tap gently but securely after completing the check.
Check the taps for gas leaks with a gas leak test solution
(retighten if necessary).
If the pressure is not sufficient, make sure the gas supply line
is large enough, the supply regulator is properly adjusted,
and the total gas load for the residence does not exceed the
amount supplied.
The appliance and its individual shut off valve must be
disconnected from the gas supply piping system during any
pressure testing of that system at test pressures in excess of
1/2 psig.
12
Fuel
Type
The appliance must be isolated from the gas supply piping
system by closing its individual manual shut-off valve during
any pressure testing of the gas supply piping system at test
pressures equal to or less than 1/2 psig. Check with your gas
supplier or plumber.
Also check the orifice size on the label on the igniter bracket.
It must be the correct size for the fuel and altitude.
Do not run propane tank dry. Running the tank dry may
cause a hazardous condition due to pressure drop in
empty tank.
Solid fuel is NOT to be used with this unit.
Air Shutter Adjustment
The Ravenna gas insert has an air shutter control lever
located behind the lower door on the insert's face and to
the left of the gas valve (see Figures 15a & 15b). The lever
is linked to the primary air shutter on the main burner. The
air shutter regulates the amount of primary air the burner
receives and therefore how clean the insert burns. The air
shutter should only be adjusted by a qualified gas technician. The insert should burn for about 15 minutes with the
logs installed before adjusting the air shutter. More air will
result in shorter flames and less color, less air will result
in bigger flames and more color. To adjust the air shutter,
insert a regular screwdriver into the slide adjustment and
slide it side to side (see Figures 15a & 15b). Caution: The
air shutter should never be set so as to make the tips of
the flames sooty or create sooting on the viewing glass,
logs, or heat exchanger. If soot begins to form after burning, the air shutter should be opened gradually until the
sooting condition stops. Gas quality and gas pressure
may vary, which can affect the burning characteristics
of the insert.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
FOR YOUR SAFETY READ BEFORE OPERATING
WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS
EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, INJURY, OR LOSS OF LIFE.
CAUTION: HOT WHILE IN OPERATION. DO NOT TOUCH. KEEP
CHILDREN, FURNITURE, GASOLINE, AND OTHER LIQUIDS WITH
FLAMMABLE VAPORS AWAY. NEVER OPERATE UNIT WITH GLASS
OFF OR ATTEMPT TO REMOVE THE GLASS WHILE HOT.
Figure 15a
A. This appliance is equipped with a piezo ignition device
to light the pilot. When lighting the pilot, follow these
instructions exactly.
B. BEFORE LIGHTING, smell around the appliance area for
gas. Be sure to smell next to the floor, because some gas
is heavier than air and will settle on the floor.
See Detail Shutter
Adjustment
Moving shutter
bracket to the right
will open shutter,
to the left will close
shutter.
Figure 15b
WHAT TO DO IF YOU SMELL GAS:
Shutter Adjustment Detail
SHUTTER ADJUSTMENT DETAIL
Operating Instructions
Pre-Lighting Checklist
Be sure to check these items before the initial lighting of
the insert:
cThe insert gas label corresponds to the gas supply available - that is "natural gas" for natural gas or "LP gas" for
LP gas.
cGas pressure has been checked carefully - see Page 12.
cAll gas fittings have been checked for leaks.
cAll clearances to combustibles have been met-see Page 8.
cAll combustible materials have been removed from the
area in front of the insert.
cAll vented areas of the insert face are unobstructed.
cHouse is ventilated to clear initial paint curing odors - see
Page 15.
cAll packaging materials have been removed from the
firebox.
cWhile insert is cool, fingerprints or other marks have been
cleaned from any gold or nickel surfaces with denatured
alcohol and a soft cloth. Marks left on these surfaces
may become etched into the finish if not removed prior
to burning the unit.
cBrick panels and log set have been installed.
cThe glass door is in place and is properly sealed.
Lighting Instructions
The following is a copy of the operating and lighting instructions found with each insert:
DO NOT try to light the appliance.
DO NOT touch any electric switch, DO NOT use any phone in the building. Immediately call
your gas supplier from a neighbor's phone. Follow the gas
supplier's instructions. If you cannot reach your gas supplier,
call the fire department.
C. Use only your hand to push in or turn the gas control
knob. Never use any tool. If the knob will not push in or
turn by hand, don't try to repair it, call a qualified service
technician. Force or attempted repair may result in a fire
or explosion.
D. DO NOT use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
OPERATING INSTRUCTIONS
CAUTION: Your Lennox™ gas INSERT MUST ALWAYS BE
OPERATED WITH GLASS IN PLACE.
STOP!! Read the safety information above before proceeding.
1. Open the lower door. Make sure gas supply shut-off cocks
are open and ON/OFF rocker switch is "OFF." If equipped
with a thermostat, set it to the lowest setting.
2. Turn off all electrical power to the appliance.
3. Push in gas cock dial slightly and turn clockwise to
"OFF."
NOTE: Dial cannot be turned from "PILOT" to "OFF" unless
dial is pushed in slightly. Do not force.
4. Wait five minutes to clear out any gas. Then smell for gas,
including near the floor. If you smell gas, STOP! Follow
"B" above. If you don't smell gas continue.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
13
5. Locate the pilot by looking over the top of the left front
log. A blue flame will be seen when the pilot is lit.
6. Turn the gas control knob counter-clockwise to
the "PILOT" position.
7. Push the knob all the way in and hold in that position.
Immediately light the pilot by pressing the igniter button
several times until pilot is lit. Continue to hold the knob
in for about 30 seconds after the pilot is lit. Realease
knob and it will pop back out. Pilot should remain lit. If it
goes out, repeat steps 4-8 holding knob in an additional
15 seconds after pilot is lit. If knob does not pop out
when released, stop and immediately call your service
technician or gas supplier. If the pilot will not stay lit after
several tries, turn the gas control knob to "OFF" and call
your service technician or your gas supplier.
8. After pilot is lit, turn gas control knob counter-clockwise to "ON." Knob can only be turned to "ON" if the
knob has popped out.
9. To turn burner on, turn "ON/OFF" rocker switch to "ON"
or set the thermostat to the desired temperature above
room temperature.
10. Adjust the flame height (and heat output) by turning the
flame height knob clockwise for full flame and
counter-clockwise for reduced flame.
11. Turn on the electric power to the appliance and set the
blower to the desired air flow after it turns on when the
appliance reaches operating temperature.
WARNINGS
• Improper installation, adjustment, alteration,
service or maintenance can cause injury or
property damage. For assistance or additional
information, consult a qualified installer, service
agency or your gas supplier.
• Operation of this appliance when not connected
to a properly installed and maintained venting
system can result in carbon monoxide (CO)
poisoning and possible death.
• Carbon monoxide poisoning – early signs of
carbon monoxide poisoning resemble the flu
with headaches, dizziness, or nausea. If you
have these signs, get fresh air at once! Have the
heater inspected by a qualified service technician. Some people are more affected by carbon
monoxide than others. These include pregnant
women, people with heart or lung disease or
anemia, those under the influence of alcohol,
and those at high altitudes.
Robertshaw Millivolt Gas Valve
TO TURN OFF GAS TO APPLIANCE
TH
1. Turn off the "ON/OFF" rocker switch and/or thermostat (if
installed) to its lowest setting.
2. Turn off electric power to the appliance if service is to
be performed.
3. Push in gas control knob slightly and turn clockwise
to "OFF." Do not force.
TP
TP/TH
Piezo Igniter
Allumeur
SHUTDOWN PROCEDURE
Gas Pilot Hood
Veilleuse à gaz
Igniter (electrode)
Thermopile
Allumeur
Thermocouple
To turn off the burner, turn the rocker switch to "OFF" or
adjust the thermostat (if installed) to a setting below room
temperature. The pilot will remain lit for future burner ignition. For complete shutdown, see "TO TURN OFF GAS TO
APPLIANCE" above.
Figure 16
14
ON/OFF Switch
Interrupteur
OFF
This appliance needs fresh air for safe operation and
must be installed so there are provisions for adequate
combustion and ventilation air.
Flame Height Control
Knob (HI/LO)
ON
Gas Control Knob
(Pilot / On / Off)
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
PILOT ASSEMBLY
Flame Color & Behavior
Quiet Operation
Your Ravenna™ gas insert is designed for maximum heating efficiency. Therefore, upon lighting of the main burner
the flames will be semi-transparent or “bluish.” After 10-20
minutes of operation the logs will heat up and the flames
will become a yellow/orange color.
As the Ravenna™ gas insert is burning, a number of normal
operational sounds may be heard. The flow of gas through the
gas valve and orifice may make a rushing or whistling noise.
If this noise is objectionable, it can be reduced by turning
down the flame. Turning down the flame can reduce total
heat output by more than 30%. When the blower turns on,
the sound of rushing air may be heard. The blower sounds
may be reduced by adjusting the speed control located on
the blower assembly. Also, a slight clicking sound may be
heard as the gas valve or blower switch turn on and off.
Adjusting the insert to cause the flames to turn orange
sooner may result in poor combustion, sooting, and a
hazardous situation. See Figure 17 showing proper flame
appearance.
When testing for proper operation - If an optional thermostat is installed adjust it to its highest temperature setting. Visually determine that main burner gas is burning properly: i.e., no floating, lifting or flashback. Adjust the primary air
shutter(s) as required. Check for proper main burner operation at both high and low flame.
Blower Operation
Your Ravenna gas insert comes equipped with a 150 CFM
blower with a variable speed control and an automatic
temperature activated On/Off snap switch.
Operation:
Burner Flame Appearance
Soot at
Flame Tip
Dark Orange
Flame
No Blue Flame
Center
Soot above
Flame Tip
Ports on Pan
Burner Assembly
IMPROPERLY
BURNING FLAME
No Soot at
Flame Tip
Semi-Transparent
Yellow Flame
Blue Flame
Center
PROPERLY
BURNING FLAME
Figure 17
Paint Curing
This insert has been painted with StoveBright high temperature metallic stove paint. It leaves the factory dry to
the touch, but finishes curing as the insert is used. Fire
the insert four successive times for ten minutes each time
with a five minute cool down between each firing. Ventilate
the house during these first firings as the paint gives off an
unpleasant odor. It is recommended that persons sensitive
to an imbalance in the indoor air quality avoid the insert
during the curing process.
1.Plug the blower power cord into a grounded (three-prong)
outlet. This appliance is equipped with a three-prong
(grounding) plug for your protection against shock hazard
and should be plugged directly into a properly grounded
three-prong receptacle. Do not cut or remove the grounding prong from this plug.
2.After the insert warms up, the fan will turn on if the speed
control (located at the right below the firebox) is left in
the "ON" position. The fan will not operate until the insert
is warm.
3.Once the fan turns on, turn the knob to the desired speed.
No further adjustment is necessary.
4.If you do not wish to have the fan on, turn the knob until
it clicks into the "OFF" position.
Optional Wall Thermostat
If an optional wall thermostat is to be installed, install the
thermostat per the manufacturers instructions (provided with
the thermostat). Failure to follow manufacturers instructions
could result in a malfunction. Pay special attention to the
thermostat location requirements. If the location requirements are not adhered to the appliance, erratic operation
or failure may occur. Do not mount the thermostat where it may be affected by:
• Radiant heat from this appliance, fireplaces, sun or other
heat sources.
• Drafts or dead spots behind doors or in corners.
• Hot or cold air from ducts.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
15
Operating Options
The rocker switch on your Ravenna™ gas insert is used to
turn the burner on and off while the pilot is on. The rocker
switch can be installed in the hole in the right side of the
top surround panel or in the hole in the panel to the left
of the igniter button. The hole in the panel is covered by a
label which must be carefully cut out before installing the
rocker switch. The switch must be disconnected from the
coil of wire to which it is attached, the plastic nut unscrewed
from the back side of the switch, and then the switch can
be inserted into the hole at either location. If the switch is
to be located in the surround, route the wire behind the
igniter bracket and through the hole in the lower right side
of the insert. Attach the three plastic adhesive wire restraints
(found in the bag in the firebox) to the side surround panel.
Feed the wire through these restraints and up to the switch.
Care should be taken to ensure the wire does not come in
contact with the hot surfaces of the firebox. Reconnect the
wires to the switch.
A wall-mounted switch, a millivolt wall thermostat, or a
remote control, can be used to supplement the rocker
switch. The gas valve is powered by millivolts generated by
the pilot assembly. This millivolt system is very sensitive to
electrical resistance, therefore, make sure all connections
are tight, clean, and free from corrosion. Do not splice any
millivolt wires. Consult the table on this Page to determine
the proper gage of wire for the thermostat or wall switch
connections. This table refers to the total length of the wire
(out to the switch and back). The thermostat must be a
millivolt type. A 24-volt furnace thermostat will not work.
Never hook up household current - 120 Volts - to the millivolt system. It is not recommended to hook up any more
than two switches to the insert (for example a rocker switch
and a wall thermostat). Additional switches may affect the
system resistance and increase the chance of the burner not
igniting. Follow the instructions included with the thermostat
or remote control for wiring.
Millivolt Control
Schematic
Piezo Igniter
Sparker
The thermostat, remote control, and rocker switch will turn
the burner on and off independently. Be sure to set the rocker
switch to the “OFF” position when using the thermostat or
remote control and set the thermostat or remote control to
the lowest temperature when you wish to use the rocker
switch only, otherwise one may override the other. If a remote thermostat is to be used with the insert, do not place
the receiver under the firebox.
Thermostat Wire
Wire Size
Maximum Length
12 Gage
100 Feet
14 Gage
64 Feet
16 Gage
40 Feet
18 Gage
25 Feet
20 Gage
16 Feet
Millivolt Control System
This fireplace operates on a millivolt control system. As
such, no additional power supply is needed for the fireplace
to heat. The pilot assembly contains a thermocouple, that
when heated by the pilot flame, generates electricity (millivolts- mV=1/1000 of a volt) which opens a valve allowing
gas to flow to the pilot assembly. The pilot assembly also
contains a thermopile, that when heated by the pilot flame,
generates electricity that flows to terminal #1 (labeled
THTP) on the gas valve. When the electricity is conducted
from terminal #1 through the on/off switch, thermostat, or
receiver of the remote control to terminal #3 (labeled TH)
on the gas valve, the main burner will ignite. Pilot Hood
Thermocouple
Thermopile
Wiring Terminals
Pilot Assembly
TH
TP
Pilot Gas Line
Gas Inlet
TH/TP
White
Brown
Figure 18
16
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
ON/OFF Rocker Switch,
Thermostat, or Remote
Thermostat
Maintenance & Servicing
Millivolt and System Checks
Maintenance Checklist
The following should only be performed by a qualified
service technician.
Caution: Label all wires prior to disconnection when
servicing controls. Wiring errors can cause improper
and dangerous operation. Verify proper operation after
servicing.
Check
Test
To
Test
Connect
Meter
Leads to
Terminals
Thermostat
Connects
Meter
Reading
Should Be
A
Complete
System
2&3
Closed
100 MV
or More
B
Thermopile
Output
1&2
Open
Greater
Than
325 MV
C
System
Resistance
2&3
Closed
2.5 Ohms
1.Annual inspection should be made and the following
checks performed:
Proper Pilot Flame Appearance
oWhen unit is cool, remove glass and inspect burner for
dirt, soot, and lint accumulations, and remove if necessary. If excessive soot accumulation is present on burner,
have a qualified service technician adjust the burner for
proper combustion.
o
Clean inside of glass with gas fireplace glass cleaner.
NEVER attempt to remove or clean the glass when the
unit is hot.
o
Check the hot air outlet vents for lint or other accumulations. Never block or restrict vent openings, obstruct flow
of ventilation air, or use vents other than those approved
for use with the Ravenna gas insert.
o
Check that the chimney and its outlet are open and free
of soot, blockage, or debris.
Figure 19
o
Check gaskets once a year. Gaskets must be tight. Replace
if necessary.
Glass Door Cleaning and Maintenance
o
Inspect the pilot system for proper flame. NEVER ADJUST
THE PILOT until after the gas pressure has been checked
and the supply lines have been completely bled (this may
take an hour or more when bleeding through the pilot).
All pilots are checked and burned at the factory prior to
shipment. The pilot adjustment screw is located below the
ON/OFF/PILOT control knob. Remove the pilot adjusting
cover with a flat-bladed screwdriver to access the pilot
adjusting screw. Adjust the pilot screw to properly size the
flames. The flames should directly contact the thermopile
and extend across the main burner ports. Be careful not
to back the screw out of its threads. Replace the cover
and check for gas leaks using a gas leak test solution.
o
Check that the area around the insert is kept clear and is
free of combustible materials, gasoline, and other flammable vapors and liquids.
o
Check the millivolt system as per the table on this page.
2.The viewing glass should be cleaned periodically (see
Glass Maintenance).
Cleaning: When cool, the glass may be cleaned with a clean,
soft cloth and Windex. For cleaning white condensation from
the interior glass, use KEL KEM gas fireplace glass cleaner
available from your insert dealer. Use of caustic or abrasive
cleaners may damage the glass. DO NOT operate the insert
with broken glass. DO NOT clean door or glass when hot. DO
NOT abuse the glass door by striking or slamming it shut.
DO NOT use substitute materials if replacing the glass. DO
NOT spray commercial glass cleaner with ammonia on the
door and glass gasket as it may dissolve the gasket glue.
Glass Replacement: The glass in the insert door cannot be
replaced separately. Should the glass be damaged, the entire
glass, gasket, and metal frame assembly must be replaced
as a unit. This replacement glass assembly is available from
your Lennox Hearth Products dealer. The glass is neo-ceramic
and alternative types must not be used.
WARNING: Do not operate appliance with the glass panel
removed, cracked, or broken. Do not remove glass door
while the insert is hot. Replacement of the glass door
should be done by a qualified service technician.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
17
Glass Door Removal
Fuel Conversion
Caution: Do not slam or strike glass door or damage
may occur.
Converting your Ravenna™ gas insert between natural gas
and LP can be accomplished by installing a conversion kit
(valve regulator and burner orifice). Only a qualified service
technician should perform the conversion.
Do not remove the glass door while the insert is hot. To remove the glass door, pull forward and up on the top latches.
Lift the glass door up and off the lower spring latch. Be
careful not to damage or scratch the glass while handling.
To reinstall the glass, reverse the removal steps. Do not
operate the insert with the glass removed.
C onversion K it : Please see instructions provided with
conversion kit.
Blower Removal
Unplug the power supply cord from the electrical outlet prior
to removing the blower. The fan can be accessed through
the back wall of the firebox.
(A) Spring Handle Latches
(B) Door Mounting Plates
Caution: Label all wires prior to disconnection when
servicing controls. Wiring errors can cause improper and
dangerous operation. Verify proper operation after servicing (see the fan wiring diagram below for reference).
Remove the insert face, glass door, log set, and brick panels.
All of these items are fragile so handle them with care. Next,
remove the nine allen head screws around the outside of
the panel fastened to the back wall of the firebox. Rotate
the top of this panel toward the front, remove the two wires
connected to the fan, and then lift the panel with the fan attached out of the firebox. To reinstall the fan, repeat these
steps in the reverse order.
Figure 20
Glass Door Cleaning And Repair
Cleaning: Do not remove or clean the glass door when hot.
A gas door glass cleaner (available from your Lennox Hearth
Products dealer) or windex should be used with a soft cloth
to clean the glass. Do not use an abrasive cleaner. Repair: If the glass is broken in the glass door, the entire
door (metal frame, gasket, and glass) should be replaced
as a unit. This replacement unit is available from your Lennox Hearth Products dealer. Do not use substitute parts or
materials.
Electrical Requirements:
This gas insert operates without an outside power source,
however the blower requires a 120 Volt electical service
outlet. Ths appliance, when installed, must be electrically
grounded in accordance with local codes, or in the absence
of local codes, the National Electrical Code ANSI/NFPA 70
- latest edition. (See Operating Options for thermostat and
ON/OFF switch information).
Caution: Do not operate this insert with broken glass.
Blower Wiring
Schematic
Power Source
Ground (Green)
Fan Snap Switch
Fan Speed Control
Black (Hot)
White (Neutral)
White
Black
Blower
18
Figure 21
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Troubleshooting
NOTE: When troubleshooting the gas control system, be sure the external gas shut off valve, located at the gas supply inlet is in the “ON” position.
IMPORTANT: Call your gas supplier or plumber for additional help with any gas control problem. Valve system
troubleshooting should only be accomplished by a qualified service technician.
SYMPTOM
Thin black coating (soot)
forms on the viewing
glass, logs, or firebox
PROBABLE CAUSE
Improper log or ember
placement
Improper air shutter
setting
Not enough combustion air
Humming or whistling
coming from insert.
A change in flame appearance or burner operation.
Spark igniter will not light
pilot after repeated tries.
CORRECTIVE ACTION
See Brick Panel and Log Set Installation on Pages 10 & 11. If there is soot in one
specific location, the rockwool below this location needs to be adjusted. This can be done
by pulling embers forward slightly. If the flames have soot tails, the shutter will need to
be opened.
If sooting continues open air shutter (see Air Shutter Adjustment on Page 12 & 13)
Check for debris obstructing air flow in valve compartment under insert or in front of
lower venting.
Normal operating noise
See Quiet Operation on Page 15. The noise may be reduced by slightly turning down the
flame. Turning the flame down will reduce the heat output of the insert.
Obstructed orifice
opening
If noise is excessive or is “whistling” have your gas supplier check the regulator and
orifices and replace if necessary.
A change in gas pressure
Have your gas supplier check for correct gas pressure (7" W.C. / po. C.E. [1.74 kPa] natural gas; 11" W.C. / po. C.E. [2.74 kPa] LP gas). NOTE: NEVER BLOCK OR OBSTRUCT AIR
INTAKE OR OUTLET VENTS.
Improper ember placement
See Brick Panel and Log Set Installation on Pages 10 & 11.
No gas supplied to unit
or air in line
Check gas supply. To purge, hold in gas cock on valve for 1-2 minutes and try again.
Defective igniter (no
spark at electrode)
Check for spark at electrode and pilot, if no spark and electrode wire is properly connected, replace igniter and igniter wire.
Defective or misaligned
electrode at pilot (spark
at electrode)
Using a match, light pilot. If pilot lights, turn off pilot and trigger the igniter again. If pilot
lights, an intermittent gas/air supply may be the problem, if longer purge will not light
- check gap between electrode and pilot - should be 1/8 inch (3 mm) to have a strong
spark. If OK, replace pilot.
Pilot will not stay lit after
Low gas inlet pressure
carefully following lighting
instructions.
Defective thermopile
Check inlet pressure and adjust pilot if necessary.
Be sure wire connections from thermopile are tight at gas valve terminals.
Either rocker switch or thermostat wires may be grounded. Remove wires from valve
terminals. If pilot stays lit, trace switch wiring for a ground. May be grounded to insert or
gas supply.
Defective automatic
valve operator
Main burner will not burn.
Check open circuit millivolt output of thermopile. Reading should be greater than 325mV.
Also check thermopile wire for kinks that can cause loss of mV. Replace faulty thermopile
if wire is okay and reading is less than 325mV.
Turn valve knob to “ON” and thermostat (if installed) to 90º. Millivolt meter should read
greater than 100 mV. If reading is OK and burner does not turn on, replace gas valve
(qualified service technician only).
Pilot has gone out
See Lighting Instructions.
Rocker switch, thermostat, or wires defective
Disconnect rocker switch and thermostat wires at terminals 1 and 3 on valve. Jumper
across from 1 to 3 with pilot lit. If burner comes on either rocker switch, thermostat, or
wiring is not functioning.
Thermopile may not be
generating sufficient
millivolts
Check thermopile with millivolt meter (see Maintenance and Servicing), recheck symptom #2.
19
Replacement Parts
Accessories
Ravenna™ 33/40 (RDV33/40)
Part Number
H3132
H3045
H6010
H5922
H5938
H5939
H5941
H5924
H5963
H5926
H5971
H5925
H5929
H5927
H5972
H5433
H5434
H6013
H5875
H5655
H5744
H6007
H5745
H4635
70005
H0251
H5975
H5977
H5730
H5858
H2739
H5863
H5864
H3130
H5989
H5839
H5913
H5914
H5980
H5893
H5908
H5910
75169
75170
75010
20
Description
Cassette Assembly NG 33,000 BTU (if LP, also requires H5433 Conversion Kit)
Cassette Assembly NG 40,000 BTU (if LP, also requires H5433 Conversion Kit)
Burner Assembly Pilot Assembly Convertible, NG or LP Gas Control Valve NG (if LP, also requires H5941 LP Regulator)
Regulator, NG Regulator, LP Orifice Main Burner #36 NG 33,000 BTU Orifice Main Burner 1/8" NG 40,000 BTU Orifice High Altitude Main Burner #37 NG 33,000 BTU Orifice High Altitude Main Burner #30 NG 40,000 BTU Orifice Main Burner #51 LP 33,000 BTU Orifice Main Burner #49 LP 40,000 BTU Orifice High Altitude Main Burner #52 LP 33,000 BTU Orifice High Altitude Main Burner #53 LP 40,000 BTU
Conversion Kit, NG to LP Conversion Kit, LP to NG Blower W/Mounting Bracket Blower Snap Switch Blower Speed Control (rheostat)
On/Off Switch On/Off Switch Wires Only Piezo Igniter Wall Thermostat, Digital AC Remote Control Thermostat
DC Remote Control, Deluxe, Thermostat
Power Cord Blower Wire Speed Control Wire (for rheostat)
Log Set Brick Panel Set Bag of Embers (volcanic stone)
Bag of Rockwool Firebox Door w/Glass Hardware Package Log Set Support Hinge, Right, Double Door W/Screen all Faces Hinge, Left, Double Door W/Screen all Faces Knob Extension Kit, Robertshaw, Bay Face Accent Trim, Gold, Traditional Face
Glass, Pillar Center Glass Pillar Side Knob, Gold, Set of 2 Knobs, Brushed Nickel, set of 2 Knobs, Black Nickel, set of 2
Brick Panel Kits
Cat. No.
Description
75357
Standard Brick
75359
Architectural Stone
75358
Red Brick
Surround Panel Kits
75362
29 x 41 BLACK Trim (One-piece)
75068
29 x 41 BLACK Trim
75069
29 x 48 BLACK Trim
75070
33 x 41 BLACK Trim
75071
33 x 48 BLACK Trim
75156
30 x 44 Top (Box 1 of 2)
75157
30 x 44 Sides (Box 2 of 2)
H5143
Trim/Black 29 x 41
Cast Black Surround Panels
Surround Trim Kits
H5145
Trim/Black 29 x 48
H5144
Trim/Black 33 x 41
H5146
Trim/Black 33 x 48
75036
Trim/Gold 29 x 41
75038
Trim/Gold 29 x 48
75040
Trim/Gold 33 x 41
75042
Trim/Gold 33 x 48
75037
Trim/Nickel 29 x 41
75039
Trim/Nickel 29 x 48
75041
Trim/Nickel 33 x 41
75043
Trim/Nickel 33 x 48
Gas Conversion Kits
H5433
Conversion Kit 33/40 NG to LP
H5434
Conversion Kit 33/40 LP to NG
Misc.
70005
Remote Control, Thermostat AC
H0251
Remote Control, RCL-STAT, Deluxe Thermostat DC
H4635
Wall Thermostat, Digital
75273
Round Black On/Off Switch Cover Plate
Finish Panels/front Supports
Cat. No.
Description
75252
"ZC Lower Finish Panel/Bay Face Support
*Requires Trim Pieces below"
75253
"ZC Lower Finish Panel/Reg Face Support
*Requires Trim Pieces below"
75251
Front Support Ext. Trim Black
75062
Front Support Ext. Trim Gold
75063
Front Support Ext. Trim Nickel
Traditional Face Kits
Cat. No.
Description
75167
Black Face/gold Trim
75168
Gold Face
75006
Black Nickel Face
75045
Brushed Nickel Face
Face Kits
Arched Face Kits
Screen Face Kit
75374
Black Face
75375
Gold Face
75376
Brushed Nickel Face
75377
Black Nickel Face
75028
Screen Face/double Door/black
Foundry Face Kit
75034
BLACK FACE/Black Nickel Hand-Hammered Straps
Insets
Piller Cast Face Kits
75306
ASPEN Black
75308
ASPEN Gold
75307
ASPEN Brushed Nickel
75309
ASPEN Black Nickel
75330
NAPA Black
75332
NAPA Gold
75331
NAPA Brushed Nickel
75333
NAPA Black Nickel
75378
PACIFIC Black
75379
PACIFIC Gold
75380
PACIFIC Brushed Nickel
75381
PACIFIC Black Nickel
75298
TUSCAN Black
75300
TUSCAN Gold
75299
TUSCAN Brushed Nickel
75301
TUSCAN Black Nickel
75093
Glass Door (Box 1 Of 3)
75092
Back, Pillars, Top (Box 2 Of 3)
75094
Grille/bars Traditional (Box 3 Of 3)
75091
Grille/filigree Ornate (Box 3 Of 3)
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Or
21
SAFETY / LISTING LABEL
MODEL
MODÈLE
Ravenna™
Ravenna™40
SERIAL
NO.
HOMOLOGUÉ FOYER RADIANT PRÉFABRIQUÉ AU GAZ - INSERTION DE FOYER AU GAZ - NE PAS
UTILISER AVEC DU COMBUSTIBLE SOLIDE
RDV
MANUFACTURED BY / FABRIQUÉ PAR:
LENNOX HEARTH PRODUCTS
PO BOX 987
AUBURN, WA, USA 98071
Report No. / Número de Rapport
050-S-15c-5
FACTORY EQUIPPED FOR NATURAL GAS. IF CONTROL PANEL CONTRADICTS THIS LABEL, UNIT FUEL TYPE HAS BEEN CONVERTED.
CET APPAREIL EST MUNI D’ÉQUIPEMENT POUR L’USAGE DU GAZ NATUREL. SI L’ÉTIQUETTE DU PANNEAU DES COMMANDES CONTREDIT
CETTE ÉTIQUETTE, C’EST QUE LE TYPE DE CARBURANT DE CET APPAREIL A ÉTÉ CONVERTI.
LISTED VENTED GAS FIREPLACE HEATER - FIREPLACE INSERT - NOT FOR USE WITH SOLID FUEL
TESTED TO ANSI Z21.88-2005/CSA 2.33-2005 “VENTED GAS FIREPLACE HEATERS”, UL307b, CSA P.4.1-02, AND CGA 2.17-M91.
THIS APPLIANCE MUST BE INSTALLED IN ACCORDANCE WITH LOCAL CODES, IF ANY. IF NOT, FOLLOW THE CURRENT ANSI
Z223.1/NFPA 54-LATEST EDITION (USA) OR CAN/CGA B149.1-LATEST EDITION (CANADA). THIS APPLIANCE MUST BE INSTALLED
IN ACCORDANCE WITH THE MANUFACTURER’S INSTALLATION INSTRUCTION. FOR INSTALLATION IN SOLID FUEL BURNING
FIREPLACES ONLY - MASONRY OR FACTORY BUILT. THIS VENTED GAS FIREPLACE HEATER IS NOT FOR USE WITH AIR FILTERS.
THIS APPLIANCE IS ONLY FOR USE WITH THE TYPE OF GAS INDICATED ON THE RATING PLATE AND MAY BE INSTALLED IN AN
AFTERMARKET, PERMANENTLY LOCATED, MANUFACTURED (MOBILE) HOME WHERE NOT PROHIBITED BY LOCAL CODES. SEE
OWNER’S MANUAL FOR DETAILS. THIS APPLIANCE IS NOT CONVERTIBLE FOR USE WITH OTHER GASES UNLESS A CERTIFIED
KIT IS USED.
DANGER: RISK OF ELECTRICAL SHOCK. DISCONNECT POWER BEFORE SERVICING UNIT.
IF ELECTRICALLY CONNECTED, CONNECTIONS AND GROUNDING MUST BE IN ACCORDANCE WITH LOCAL CODES, IF ANY.
IF NOT, FOLLOW THE CURRENT NATIONAL ELECTRICAL CODE ANSI/NFPA 70-LATEST EDITION (USA) OR CSA C22-1-LATEST
EDITION (CANADA).
RATINGS
Ravenna 40 (RDV40)
Ravenna 33 (RDV33)
NATURAL GAS
LP GAS
NATURAL GAS
LP GAS
40,000/28,000
37,500/26,000
33,000/24,000
33,000/24,000
MANIFOLD PRESSURE (IN. WC)
3.5
10.0
3.5
10.0
MIN. INLET PRESSURE (IN. WC)
5.0
10.5
5.0
10.5
ORIFICE (DMS) 0-2,000 FT (0-610 M)*
1/8”
#49
#36
#51
MAX/MIN INPUT BTUH 0-2,000 FT (0-610 M)*
*UNIT FACTORY EQUIPPED FOR 0-2000 FT/0-610 M, IN CANADA 0-4500 FT/0-1370 M
ELECTRICAL RATING: 120 VAC, 60 HZ, LESS THAN 2 AMPS
CHIMNEY - USE WITH B-VENT CHIMNEY OR SINGLE WALL GAS VENT FLEX CHIMNEY LINER LISTED TO UL 1777 OR ULC S635.
THIS APPLIANCE MUST BE PROPERLY CONNECTED TO A VENTING SYSTEM IN ACCORDANCE WITH THE MANUFACTURER’S
INSTALLATION INSTRUCTIONS.
FOR ALTITUDES ABOVE 2,000 FT/610M (IN CANADA 4500 FT/1370M) DE-RATE THE APPLIANCE BY FOUR (4)% FOR EVERY
1,000 FT (405 M).
WARNING: IF UNIT IS CONVERTED TO AN RDV40 FROM AN RDV33 ENSURE THAT THE
CLEARANCES TO COMBUSTIBLES ARE CORRECT FOR RDV40.
MINIMUM CLEARANCES TO COMBUSTIBLES
MINIMUM CLEARANCES
RDV40
RDV33
E = Top Facing to Bottom of Insert
35.5”(902mm) 31.5”(800mm)
MANTEL
F = Center of Glass to Side Facing or Side Wall 25.5”(648mm) 25.5” (648mm)
TRIM
*J = 10.5” (267mm) Mantel to Bottom of Insert 43”(1092mm) 39”(991mm)
F
* See owner’s manual for additional mantel clearances and options
J
MINIMUM FIREPLACE SIZES REQUIRED
E
A=29.75” (756mm) Front Opening
CL
G
14”(356mm)
10”(254mm)
0”(0mm)
B=19.50” (495mm) Height
RDV40
C=19.00” (483mm) Rear Width
H
0”(0mm)
2”(21mm) 4”(102mm)
H
D=16.00” (406mm) Fireplace Depth
G
HEARTH PROTECTION
G 13”(330mm) 10”(254mm)
0”(0mm)
G = Minimum Hearth Protection RDV33
H
0”(0mm)
2”(21mm) 4”(102mm)
G = from Front of Insert
H = Vertical Distance from Insert
Note: Hearth protection to be min. 3/8” (10mm) thick
H = Bottom to Combustible Material
non-combustible or equivalent, with a k factor of .84.
CAUTION: HOT WHILE IN OPERATION. DO NOT TOUCH. SEVERE BURNS MAY RESULT. KEEP
CHILDREN, CLOTHING, FURNITURE, GASOLINE AND OTHER LIQUIDS HAVING FLAMMABLE VAPORS
AWAY. KEEP BURNER AND CONTROL COMPARTMENT CLEAN. SEE INSTALLATION AND OPERATING
INSTRUCTIONS ACCOMPANYING APPLIANCE. FOR USE WITH GLASS DOORS CERTIFIED WITH THIS
APPLIANCE ONLY. DO NOT OPERATE THE APPLIANCE WITH GLASS REMOVED, CRACKED OR BROKEN.
REPLACEMENT OF THE PANEL(S) SHOULD BE DONE BY A LICENSED OR QUALIFIED PERSON.
WARNING: IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN
CAUSE INJURY OR PROPERTY DAMAGE. REFER TO THE OWNER’S INFORMATION MANUAL PROVIDED
WITH THIS APPLIANCE. FOR ASSISTANCE OR ADDITIONAL INFORMATION CONSULT A QUALIFIED
INSTALLER, SERVICE AGENCY OR GAS SUPPLIER.
Part No./ No. pièce #36200 Rev. A, 05/2007
22
DO NOT REMOVE OR COVER THIS LABEL
TESTÉ SELON LA NORME ANSI Z21.88-2005/CSA 2.33-2005 «FOYER RADIANT AU GAZ», UL307B, CSA P.4.1-02, ET CGA 2.17-M91.
CET APPAREIL DOIT ÊTRE INSTALLÉ CONFORMÉMENT AUX EXIGENCES DES CODES RÉGIONAUX ET DU CODE D’INSTALLATION
ANSI NFPA 54-DERNIÈRE ÉDITION (ETATS-UNIS), OU CAN/CGA-B149.1-DERNIÈRE ÉDITION (CANADA). CET APPAREIL DOIT ÊTRE
INSTALLÉ SELON LES DIRECTIVES D’INSTALLATION DU FABRICANT. POUR INSTALLATION DANS DES FOYERS À COMBUSTIBLE
SOLIDE SEULEMENT - DE MAÇONNERIE OU PRÉFABRIQUÉ EN USINE. CE FOYER RADIANT AU GAZ À ÉVACUATION N’EST PAS
CONÇU POUR ÊTRE UTILISÉ AVEC DES FILTRES À AIR.
CET APPAREIL DOIT ÊTRE UTILISÉ AVEC LE TYPE DE GAZ INDIQUÉ SUR LA PLAQUE SIGNALÉTIQUE ET PEUT ÊTRE INSTALLÉ
DANS UNE MAISON PRÉUSINÉE OU DANS UNE MAISON MOBILE FIXE, LÀ OÙ LES CODES RÉGIONAUX LE PERMETTENT. VOIR LE
MANUEL D’ENTRETIEN POUR PLUS DE DÉTAILS. CET APPAREIL NE PEUT PAS ÊTRE CONVERTI POUR L’USAGE AVEC D’AUTRES
TYPES DE GAZ À MOINS D’UTILISER UNE TROUSSE DE CONVERSION HOMOLOGUÉE.
DANGER: RISQUE DE CHOC ÉLECTRIQUE. DÉBRANCHEZ L’APPAREIL AVANT D’EN FAIRE L’ENTRETIEN.
SI L’APPAREIL REQUIERT UN BRANCHEMENT ÉLETRIQUE, LES RACCORDEMENTS ET LA MISE À LA TERRE DOIVENT ÉTRE
CONFORMES AUX EXIGENCES DES CODES RÉGIONAUX ET DU CODE D’INSTALLATION ANSI/NFPA 70 OU CSA C22-1.
Ravenna 40 (RDV40)
SPÉCIFICATIONS
Ravenna 33 (RDV33)
GAZ NATUREL
GAZ PROPANE
GAZ NATUREL
GAZ PROPANE
40000/28000
37500/26000
33000/24000
33000/24000
PRESSION À LA SORTIE (IN. WC/C.E.)
3,5
10,0
3,5
10,0
PRESSION MINIMUM D’ENTRÉE DU GAZ (IN. WC/C.E.)
5,0
10,5
5,0
10,5
1/8”
#49
#36
#51
ENTRÉE MAX/MIN BTU/HR 0-4500 pi (0-1370 M)*
ORIFICE (DMS) 0-4500 pi (0-1370 M)*
*L’APPAREIL PRÉUSINÉ EST MUNI D’ÉQUIPEMENT POUR 0-2000 PIEDS (0-610 M). AU CANADA 0-4500 PIEDS (0-1370M).
SPÉCIFICATIONS ÉLECTRIQUE 120 VCA, 60 HZ, MOINS DE 2 AMPÈRES
CHEMINÉE - ÉVACUATION :INSTALLER AVEC DE L’ÉVENT À GAZ DE TYPE B-VENT OU UN CONDUIT FLEXIBLE À SIMPLE
PAROI HOMOLOGUÉ COMME TUBAGE.
CET APPAREIL DOIT ÊTRE RELIÉ À UN SYSTÈME D’ÉVACUATION TEL QUE SPÉCIFIÉ DANS LE MANUEL D’INSTALLATION DU
FABRICANT.
EN ALTITUDE, AU-DELÀ DE 2000 PI/610 M, (AU CANADA 0-4500 PI/0-1370M) LA CAPACITÉ ÉNERGÉTIQUE DE L’APPAREIL
DIMINUE DE QUATRE (4)% POUR CHAQUE 1000 PI (405 M).
SI LE MODÈLE RDV33 EST CONVERTI COMME MODÈLE RDV40, ASSUREZ VOUS QUE LES
DÉGAGEMENT AUX COMBUSTIBLES SONT RESPECTER SELON LE MODÈLE RDV40.
DÉGAGEMENTS AUX COMBUSTIBLES - RDV40
RDV33
E = Dessus du foyer à partir de la base
35.5”(902mm) 31.5”(800mm)
F = Mur latéral à partir du centre du foyer
25.5”(648mm) 25.5” (648mm)
*J = 10.5” (267mm) manteau de foyer à partir
43”(1092mm) 39”(991mm)
de la base
* Voir le manuel d’entretien pour les informatinos supplémentaires reliées
aux distances à respecter pour le manteau de foyer
DIMENSIONS MINIMUMS
DE FOYER REQUISES
A = 29.75” (756mm) Ouverture avant
B = 19.50” (495mm) Hauteur
C = 19.00” (483mm) Largeur arrière
D = 16.00” (406mm) Profondeur du foyer
RDV40
G = Extension d’âtre min. devant
G = le foyer
H = Distance verticale de la base de
H = l’appareil aux combustibles
RDV33
PROTECTION DU FOYER
MANTEAU
DE FOYER
DÉGAGEMENTS MINIMUMS
PIÈCE DE
FINITION
G
14”
(356mm)
10”
(254mm)
0”
(0mm)
H
0”
(0mm)
2”
(21mm)
4”
(102mm)
G
13”
(330mm)
10”
(254mm)
0”
(0mm)
H
0”
(0mm)
2”
(21mm)
4”
(102mm)
F
J
E
CL
H
G
Note: Extension d’âtre fabriqué avec
3/8” (10mm) minimum de matériaux
non-combustible ou équivalent
possédant un facteur k de 0.84.
DANGER: CET APPAREIL DÉGAGE DES TEMPÉRATURES ÉLEVÉES ET DEVRAIT ÊTRE INSTALLÉ À L’ÉCART DES
ENDROITS TRÈS PASSANTS ET LOIN DES MEUBLES ET RIDEAUX. SURVEILLEZ LES ENFANTS QUI SE TROUVENT DANS
LA PIÈCE. GARDEZ LA ZONE AUTOUR DU FOYER EXEMPTE DE MATÉRIAUX COMBUSTIBLES, D’ESSENCE ET AUTRES
VAPEURS ET LIQUIDES INFLAMMABLES. MAINTENEZ LE BRÛLEUR ET LE BOÎTIER DES COMMANDES PROPRE EN TOUT
TEMPS. VOIR LES MANUELS D’INSTALLATION ET D’ENTRETIEN QUI ACCOMPAGNENT L’APPAREIL. SEUL LE PANNEAU
VITRÉ FOURNI PAR LE MANUFACTURIER PEUT ÊTRE UTILISÉ AVEC CET APPAREIL. EN AUCUN CAS, L’APPAREIL NE
PEUT ÊTRE UTILISÉ SANS LA VITRE OU AVEC LA VITRE BRISÉE. LE REMPLACEMENT DE LA VITRE DOIT ÊTRE EFFECTUÉ
PAR UN TECHNICIEN DE SERVICE QUALIFIÉ.
AVERTISSEMENT: UNE INSTALLATION INADÉQUATE DE MÊME QU’UN AJUSTEMENT, UNE MODIFICATION, UNE
RÉPARATION OU UN ENTRETIEN INCORRECTS PEUVENT CAUSER DES BLESSURES OU DOMMAGES À LA PROPRIÉTÉ.
RÉFÉREZ-VOUS AU MANUEL D’ENTRETIEN LIVRÉ AVEC CET APPAREIL. POUR DE L’ASSISTANCE, CONSULTEZ UN
INSTALLATEUR QUALIFIÉ, UNE ENTREPRISE DE SERVICE OU UN FOURNISSEUR DE GAZ.
2007
2008
2009
DATE OF MANUFACTURE / DATE DE FABRICATION
2010
JAN
FEB MAR
JANV FEVR MARS
APR
AVR
MAY
MAI
JUN
JUIN
JUL
JUIL
AUG SEP OCT
AOÛT SEPT OCT
N’ENLEVEZ PAS OU NE COUVREZ PAS CETTE ÉTIQUETTE
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
NOV
NOV
DEC
DEC
IGN
Lighting Label
FOR YOUR SAFETY READ BEFORE OPERATING
POUR VOTRE SÉCURITÉ, LIRE AVANT L’ALLUMAGE
WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING
AVERTISSEMENT: SI VOUS NE RESPECTEZ PAS RIGOUREUSEMENT LES INSTRUCTIONS CI-DESSOUS, VOUS POURRIEZ ENCOURIR UN RISQUE D’INCENDIE ET/OU
A.
B.
This appliance is equipped with a piezo ignition device to light the pilot. When lighting the pilot, follow these instructions exactly.
BEFORE LIGHTING, smell around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air
and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS:
• DO NOT try to light the appliance.
• DO NOT touch any electric switch; do not use any phone in the building.
• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn the gas control knob. Never use any tool. If the knob will not push in or turn by hand, don't try
to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion.
D. DO NOT use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance
and to replace any part of the control system and any gas control which has been under water.
A. Cet appareil utilise un système d’allumage par étincelle (allumeur Piézo-électrique) pour allumer la veilleuse. Assurez-vous de suivre
rigoureusement les instructions d’allumage de la veilleuse.
B. AVANT D’ALLUMER L’APPAREIL, assurez-vous qu’il n’y a pas d’odeur de gaz près de l’appareil ni près du sol car certains gaz plus
lourds que l’air auraient tendance à s’y accumuler en cas de fuite.
QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:
• N’ALLUMEZ aucun appareil.
• Ne touchez aucune prise électrique; N’utilisez aucun téléphone dans votre édifice.
• Sortez de la maison. À partir d’un autre endroit, appelez immédiatement votre fournisseur de gaz et suivez les directives.
• S’il est impossible de joindre le distributeur du gaz, appelez les pompiers.
C. N’utilisez aucun outil pour tourner ou pousser le dispositif de contrôle du gaz. Si vous ne pouvez le faire manuellement, n’essayez
pas de réparer l’appareil. Appelez un technicien de service qualifié. Si vous tentez de forcer ou réparer le dispositif de contrôle du gaz
vous pourriez encourir un risque d’incendie et/ou d’explosion.
D. N’utilisez pas cet appareil si une de ses composantes a été émergée dans l’eau. Appelez immédiatement un technicien de service
qualifié et reconnu afin qu’il inspecte et remplace au besoin toutes pièces du système qui auraient été en contact avec l’eau.
OPERATING INSTRUCTIONS
ALLUMAGE
PROPERTY DAMAGE, INJURY OR LOSS OF LIFE.
CAUTION: HOT WHILE IN OPERATION. DO NOT TOUCH. KEEP CHILDREN, FURNITURE, GASOLINE AND OTHER LIQUIDS WITH
FLAMMABLE VAPORS AWAY. NEVER OPERATE UNIT WITH GLASS DOOR OFF OR ATTEMPT TO OPEN THE DOOR WHILE HOT.
D’EXPLOSION QUI POURRAIENT CAUSER DES DOMMANGES MATÉRIELS ET CORPORELS POUVANT ENTRAÎNER LA MORT.
DANGER: CET APPAREIL DÉGAGE DES TEMPÉRATURES ÉLEVÉES ET DEVRAIT ÊTRE INSTALLÉ À L’ÉCART DES ENDROITS TRÈS PASSANTS ET LOIN DES MEUBLES
ET RIDEAUX. GARDEZ LA ZONE AUTOUR DU FOYER EXEMPTE DE MATÉRIAUX COMBUSTIBLES, D’ESSENCE ET AUTRES VAPEURS ET LIQUIDES INFLAMMABLES.
DANGER: VOTRE APPAREIL AU GAZ LENNOX DOIT ÊTRE OPÉRÉ AVEC DES PORTES DE VERRE.
CAUTION: YOUR COUNTRY GAS APPLIANCE MUST ALWAYS BE OPERATED WITH GLASS DOOR IN PLACE.
ATTENTION! Lisez les consignes de sécurité ci-dessous avant d’opérer votre appareil.
STOP! Read the safety information above before proceeding.
1. Ouvrir la porte du bas. Assurez-vous que l’alimentation en gaz est à la position Fermée “OFF”. Si l’appareil est
Robertshaw Millivolt Gas Valve
1. Open the lower door. Make sure gas supply shut-off cocks are open and ON/OFF
équippé d’un thermostat, placez-le à la température la plus basse.
Rocker Switch is “OFF”. If equipped with a thermostat, set it to the lowest setting.
RobertShaw Vanne Gaz Millivolt
2. Couper le courant électrique qui alimente l’appareil.
2. Turn off all electrical power to the appliance.
TH
3. Enfoncez légèrement le bouton de contrôle du gaz et tournez-le dans le sens des aiguilles d’une montre
à la position “OFF”.
3. Push in Gas Control Knob slightly and turn clockwise
to “OFF”.
NOTE: Le bouton de contrôle du gaz ne peut être tourné de la position “PILOT” à “OFF” sans qu’une légère pression ne soit appliquée.
NOTE: Knob cannot be turned from “PILOT” to “OFF” unless Knob is pushed in
TP
slightly. Do not force.
4. Attendez au moins 5 minutes pour que le gaz qui se trouve dans la chambre de combustion puissse s’échapper. Si vous sentez une
TP/TH
4. Wait five (5) minutes to clear out any gas. If you smell gas, STOP! Follow “B” above.
odeur de gaz ARRÊTEZ! Référez-vous à la section B ci-dessus. Si vous ne sentez pas d’odeur de gaz, allez à la prochaine étape.
If you don’t smell gas continue.
5. Vous localiserez la veilleuse à l'arrière et au centre du brûleur derrière la bûche centrale. Une flamme bleue est visible lorsque le veilleuse
5. Locate the pilot by looking over the top of the front left log. Blue flame will be
est allumée.
Gas Control Knob
Flame Height Control Knob
seen when the pilot is lit.
(Pilot / On / Off)
6. Tournez le bouton de contrôle de gaz dans le sens inverse des aiguilles d’une montre
(HI / LO)
pour le placer sur “PILOT”.
ON
OFF
6. Turn the gas control knob counterclockwise
to the “PILOT” position.
Bouton de contrôle
- LO / HI +
7. Cet appareil de chauffage est equipé d’un système d’allumage par étincelle (allumeur Piézo-électirque), devant être utilisé pour
(Veilleuse / Ouverte / Fermée) (Commande De Taille De Flamme)
7. Push the knob all the way in and hold in that position. Immediately light the pilot by
l’allumage de la veilleuse. Poussez complètement le bouton de contrôle du gaz et le maintenir dans cette position. Appuyez
pressing the ignitor button several times until pilot is lit. Continue to hold the knob
immédiatement sur le bouton (allumeur Piézo-électrique) situé à gauche du robinet de contrôle du gaz.L’étincelle produite par
in for about 30 seconds after the pilot is lit. Release knob and it will pop back out.
ON/OFF Switch
l’allumeur Piézo-électrique doit allumer la veilleuse. Continuez à maintenir le bouton de contrôle dans cette position pendant environ 30
Piezo Igniter
Interrupteur
Allumeur
Pilot should remain lit. If it goes out, repeat steps 4-8 holding knob in an additional 15 seconds after
secondes après l’allumage de la veilleuse. Relâchez le bouton de contrôle du gaz qui reviendra à la position initiale. La veilleuse doit
pilot is lit.
rester allumée. Répétez les étapes 4 à 8 pendant 15 secondes supplémentaires si la veilleuse s’éteind.
• If knob does not pop out when released, stop and immediately call your service technician or gas
• Si le bouton de contrôle du gaz ne revient pas à la position initiale une fois relâché, appeler immédiatement un technicien qualifié ou
supplier.
votre distributeur de gaz.
• If the pilot will not stay lit after several tries, turn the gas control knob to “OFF” and call your service
• Si la veileuse ne reste pas allumée après plusieurs essais, tournez le bouton de contrôle du gaz à la position “OFF” et appelez
technician or your gas supplier.
immédiatement un technicien qualifié ou votre distributeur de gaz.
Gas Pilot Hood
8. After pilot is lit, turn gas control counterclockwise
to “ON”. Knob can only be turned “ON” if the
Veilleuse à gaz
8. Lorsque la veilleuse est allumée, tournez le bouton de contrôle du gaz dans le sens invers des aiguilles d’une montre
pour le
Igniter (electrode)
knob has popped out.
placer à la position “ON”. Le bouton de contrôle peut-être tourné à la position “ON” seulement si il n’est plus enfoncé.
Thermopile
Allumeur
9. To turn burner on, turn “ON/OFF” rocker switch to “ON” or set the thermostat to the desired temperature
9.
Pour
allumer
le
brûleur,
mettre
l’interrupteur
à
la
position
“ON”
ou
ajustez
le
thermostat
à
la
température
souhaitée.
above room temperature.
Thermocouple
10. Ajustez la flamme et la température souhaitée en tournant le bouton de réglage de la flamme dans les sens des aiguille d’une montre
10. Adjust the flame height (and heat output) by turning the flame height knob clockwise
for reduced
pour l’abaisser et dans le sens contraire
pour l’augmenter.
flame and counterclockwise
for full flame.
11. Allumez l’alimentation électrique de l’appareil.
11. Turn on all electrical power to the appliance.
12.
Ajustez
le
ventilateur
au
volume
désiré
lorsque
l’appareil
aura
atteint la température de fonctionnement.
12. Set the blower to the desired air flow after it turns on when the appliance reaches operating temperature.
PILOT ASSEMBLY
POUR COUPER L’ALIMENTATION EN GAZ DE L’APPAREIL
TO TURN OFF GAS TO APPLIANCE
1. Turn off the “ON/OFF” rocker switch and/or thermostat (if installed).
2. Turn off electric power to the appliance if service is to be performed.
3. Turn gas control knob clockwise
to "OFF". Do not force.
This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate
combustion and ventilation air. See Installation and Operation Manual accompanying appliance.
WARNING: Improper installation, adjustment, alteration, service or maintenance can
cause injury or property damage. For assistance or additional information, consult a
qualified installer, service agency or your gas supplier.
Operation of this appliance when not connected to a properly installed and maintained venting system can result
in carbon monoxide (CO) poisoning and possible death.
SHUTDOWN PROCEDURE
1. To turn off the burner, switch the rocker switch to “OFF” or adjust the thermostat to a setting below room temperature
(if installed). The pilot will remain lit for future burner ignition.
#36200 Rev. A, 04/07
For complete shutdown: See “TO TURN OFF GAS TO APPLIANCE” above.
1. Fermez l’interrupteur et/ou le thermostat «MARCHE/ARRÊT».
2. Coupez l’alimentation électrique de l’appareil si vous prévoyez en faire le service.
3. Tournez le bouton de commande du gaz dans le sens des aiguilles d’une montre
à “OFF”. Ne le forcez pas.
Cet appareil a besoin d’air frais pour opérer sécritairement et doit être installé pour qu’il y ait un apport en air suffisant. Référezvous aux manuels d’entretien et d’installation fournis avec l’appareil.
AVERTISSEMENT: Une installation inadéquate, un mauvais ajustement, une altération ou toutes autres modifications
inappropriés pourraient entraîner des blessures physiques et/ou des dommanges matériels. Référez-vous au guide
d’utilisation fourni avec ce foyer. Pour assistance ou information supplémentaires contactez un installateur qualifié,
un agent de service ou un fournisseur de gaz.
Si vous opérez cet appareil sans qu’il ne soit correctement raccordé à un conduit d’évacuation, vous pourriez risquer d’être
empoisonné au monoxyde de carbone (CO) ce qui pourrait entraîner des conséquences grave ou la mort.
PROCÉDURE D’ARRÊT
1. Pour arrêter le brûleur, mettre l’interrupteur à la position “OFF” ou ajustez le thermostat à une température en dessous de la
température ambiante. La veilleuse restera allumée pour permettre un alummage ultérieur.
IGN
Pour un arrêt complet: Consultez la procédure ci-dessus «POUR COUPER L’ALIMENTATION EN GAZ DE L’APPAREIL».
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
23
Warranty
Normally, all parts should be ordered through your Lennox distributor or
dealer. Parts will be shipped at prevailing prices at time of order.
Your gas appliance is covered by a limited warranty (provided with
appliance). Please read the warranty to be familiar with its coverage.
Retain this manual. File it with your other documents for future reference.
Product reference information
We recommend that you record the following important information
about your appliance. Please contact your Lennox Hearth Products dealer
for any questions or concerns. For the number of your nearest Lennox
Hearth Products dealer, please call 1-800-9-LENNOX.
Replacement parts
See Page 20 for a complete replacement parts list. Use only parts supplied from the manufacturer.
When ordering repair parts, always give the following information:
1. The model number of the appliance.
2. The serial number of the appliance.
3. The part number.
4. The description of the part.
5. The quantity required.
6. The installation date of the appliance.
If you encounter any problems or have any questions concerning the
installation or application of this system, please contact your dealer.
LENNOX HEARTH PRODUCTS
1110 West Taft Avenue
Orange, CA 92865
Visit us at www.Lennox.com
Your Appliance's Model Number________________________________________
Your Fireplace Insert’s Serial Number_ ___________________________________
The Date On Which Your Fireplace Insert Was Installed_______________________
The Type of Gas Your Fireplace Insert Uses________________________________
Your Dealer's Name__________________________________________________
Fuel Type (Check one) c Natural Gas c Propane Gas (LP)
�
Lennox™ reserves the right to make changes at any time, without notice, in design,
materials, specifications, prices and also to discontinue colors, styles and products.
Consult your local distributor for fireplace code information.
Printed in U.S.A. © Lennox Hearth Products 2007
24
P/N 775,218M REV. B 12/2007
1110 West Taft Avenue • Orange, CA 92865