Loewe 52 Operating instructions

Operating instructions
TV
3 3 2 4 7 0 2 3
233–33247.023
– Individual 52 Compose Full-HD+ 100
– Individual 46 Compose Full-HD+ 100
– Individual 40 Compose Full-HD+ 100
Contents
Remote control – TV functions................................................................. 3
Control unit front side of the device........................................................ 4
Connections rear side of the device – Compose 40................................. 5
Connections rear side of the device – Compose 46 / Compose 52.......... 6
Welcome.................................................................................................... 7
Scope of delivery.............................................................................................7
About this operating manual...........................................................................7
TV set equipment.............................................................................................7
Trademarks......................................................................................................7
Acknowledgements.........................................................................................7
Operating convenience with wizards................................................................8
The wizards in overview...................................................................................8
Info display and TV index.................................................................................8
For your safety.......................................................................................... 9
Environmental protection....................................................................... 10
Initial installation.................................................................................... 11
Installing the TV set.......................................................................................11
Preparing the remote control unit..................................................................11
Connecting the TV set....................................................................................11
Turning the set on/off....................................................................................12
First installation wizard..................................................................................12
Positioning/aligning DVB-T antenna...............................................................14
Operating convenience........................................................................... 15
General information on menu operation.........................................................15
The info display.............................................................................................15
The index in the TV set...................................................................................16
The Assist+ menu..........................................................................................16
TV menu – Overview diagram........................................................................17
Radio menu – Overview diagram...................................................................17
Daily operation....................................................................................... 18
Select station.................................................................................................18
Select video source........................................................................................19
Adjusting the sound......................................................................................20
Adjusting the picture.....................................................................................21
Operation without remote control..................................................................21
Button functions............................................................................................22
Managing stations.................................................................................. 24
TV stations....................................................................................................24
Put together / change favourites lists.............................................................27
Picture in Picture..................................................................................... 28
Picture in Picture (PIP)...................................................................................28
Configure Picture in Picture (PIP) mode..........................................................29
Electronic Programme Guide.................................................................. 30
Electronic Programme Guide – EPG................................................................30
Configuring EPG............................................................................................31
- Teletext.................................................................................................... 32
Teletext.........................................................................................................32
Teletext menu................................................................................................33
Digital teletext (MHEG-5)...............................................................................33
Radio....................................................................................................... 34
Radio mode .................................................................................................34
EPG – Electronic Programme Guide (radio).....................................................34
DVB.......................................................................................................... 35
Conditional Access module (CA module)........................................................35
Software update............................................................................................36
Other settings......................................................................................... 38
Parental lock.................................................................................................38
Timer functions..............................................................................................38
On-screen displays.........................................................................................39
Time and date...............................................................................................39
Operating additional equipment............................................................ 40
Connection wizard.........................................................................................40
Devices to the connections AV1/AV2/AVS.......................................................42
Devices to the HDMI (DVI) connections..........................................................44
Devices to the PC IN connection....................................................................45
Devices to the Component IN connection.......................................................46
Sound components wizard.............................................................................47
TV speakers...................................................................................................47
Speaker system Loewe Individual Sound on the Dolby Digital Decoder
of the TV set..................................................................................................48
Connecting other speaker systems or active speakers to the Dolby Digital
Decoder........................................................................................................49
Adjusting the speaker system.........................................................................49
Connecting audio amplifiers..........................................................................52
Assignment of the digital audio input............................................................53
Audio connection in HDMI (DVI) devices........................................................53
RS-232C interface.........................................................................................53
The direct way to record................................................................................54
Timer recording with external devices.............................................................55
PhotoViewer..................................................................................................56
MusicBox......................................................................................................58
Operating Loewe equipment..........................................................................62
Rotating the TV set........................................................................................64
Troubleshooting...................................................................................... 65
Technical data......................................................................................... 67
General data.................................................................................................67
Electrical data...............................................................................................67
Connections (max. equipment).......................................................................67
Accessories.............................................................................................. 68
Accessories....................................................................................................68
Setup possibilities..........................................................................................69
Glossary................................................................................................... 70
Index....................................................................................................... 73
Service..................................................................................................... 74
Please fold out this page.
Remote control – TV functions
(page 20).............................................................. Sound off/on
(page 62)..................... LED display for current operating mode
Switch on/off
– to standby mode...................................................(page 12)
(page 11; 62)....................................... Switch over to TV mode
Switch over to radio mode (1...............................(page 12; 34)
(page 62)................................. Switch over to operate recorder
(page 55).................................................Timer overview on/off
(page 22).......................................................Set picture format
Switch over to operate DVD player...........................(page 62)
Set sound mode......................................................(page 20)
(page 16)....................................................Assist+ menu on/off
(page 30)........................... Electronic Programme Guide on/off
Select station directly;
MENU: Enter numbers or letters...............................(page 18)
AV selection..............................................................(page 19)
PIP on/off (picture in picture)....................................(page 28)
(3 Index on/off (3............................................................(page 16)
MENU: Info texts on/off............................................(page 15)
(page 20)..................................... V+/V– Volume louder/quieter
Status display on/off (3 ..............................................(page 23)
MENU: Hide menu...................................................(page 15)
P+/P– Select station up/down...................................(page 18)
(page 32).......................................................... Teletext on/off
(page 15)............................................................... Menu on/off
(page 29)................................... PIP: Position of the PIP picture;
(page 15)........................................................ MENU: Select/set
Station list on............................................................(page 18)
MENU: Confirm/call..................................................(page 15)
Green button: (3 (page 22)........................................................Teletext functions
Red button: (3 (page 22)............................................................Call DR archive
Yellow button: (3 Previous station..............................(page 22)
Blue button: (3 Programme info on/off.....................(page 22)
Digital Recorder: Jump back/Rewind/Replay (2
(page 12).................................................... /in the wizard: Back
Digital Recorder: Jump forward/Fast forward (2
Digital Recorder: Play/Set bookmark (2
Direct recording
Radio only for DVB reception, provided the station broadcasts this.
Otherwise switch-over to an audio input.
(2
Description of the functions, see operating manual Digital Recorder.
Digital Recorder: Stop (live picture) (2
Digital Recorder:
Freeze picture/Pause (start offset TV viewing) (2
(1 If MHEG-5 is selected for the location of TV set UK or IRL during the
first installation, the button has a different funktion.
(3
-
Control unit front side of the device
Button M:
Call the menu
in the menu: up/down 
The mains switch is located
on the bottom of the TV
On/Off button:
Switch on from the standby mode
Switch off to the standby mode
Button – :
Station down
in the menu: to the left 
Button R:
Radio on/off (back to TV mode)
Switch on the radio from the standby mode
in the menu: down 
(1
DR+
Display:
= Standby
= Operation
= Operation without on-screen display
(Radio, EPG data capture or timer recording)
Button +:
Station up
in the menu: to the right
Display DR+:
DR+ = Digital Recorder inactive
(no recording, no playback)
DR+ = Digital Recorder active (offset TV viewing
or archive playback)
DR+ = Digital Recorder active
(archive recording)
Radio only for DVB reception, provided the station broadcasts this.
Otherwise switch over to an audio input.
(1 - Connections rear side of the device – Compose 40
Factory settings:
AV1: DVD player
AV2: DVD recorder
You can change this during the
initial installation (page 12) or in
the connection wizard (page 40).
Before you connect other devices
or make any changes, please start
the connection wizard (page 40)
and the sound components wizard
(page 47), and then follow the
instructions that are displayed on
the TV set.
Common Interface 1
(CI-Slot 1)
Common Interface 2
(CI-Slot 2)
USB connection 1
(USB stick/card reader)
Headphones connection
S-VHS connection (AVS)
(e.g. for camcorder)
Video in (AVS)
Audio in right (AVS)
Audio in left (AVS)
ANT2
Antenna/cable
analogue/digital
(Tuner 2)
ANT SAT
Satellite antenna
(Sat tuner 1)
ANT OUT
Connect antenna
output with ANT-TV
(tuner 1)
ANT SAT2
Satellite antenna
(Sat tuner 2)
AUDIO OUT L/R - audio output left right (analogue)
mains switch
AUDIO IN1 L/R - audio input left/right (analogue)
AUDIO IN1 C - centre audio input (analogue)
SD/HD-COMPONENT IN Cb/Pb–Cr/Pr–Y - component video inputs
AUDIO DIGITAL IN - digital audio input
AUDIO LINK - surround audio outputs (analogue)
CONTROL - rotating stand control
RS-232C - serial interface
220-240V~ 50/60Hz - mains connection
AV1
Euro-AV
socket 1
ANT-TV
Antenna/cable
analogue/digital
(Tuner 1)
AV2 (RGB)
Euro-AV
socket 2
Speakers Left (+/-) - Speakers Left (+/-)
Speakers Right (+/-) - Speakers Right (+/-)
SERVICE - service socket
AUDIO IN2 - audio input (analogue)
HDMI2 - HDMI (DVI) input 2
HDMI1 - HDMI (DVI) input 1
PC IN - VGA/XGA input
USB - USB connection 2 (USB stick/card reader)
AUDIO DIGITAL OUT - digital audio output
-
Connections rear side of the device – Compose 46 / Compose 52
Factory settings:
AV1: DVD player
AV2: DVD recorder
You can change this during the
initial installation (page 12) or in
the connection wizard (page 40).
Before you connect other devices
or make any changes, please start
the connection wizard (page 40)
and the sound components wizard
(page 47), and then follow the
instructions that are displayed on
the TV set.
USB connection 1
(USB stick/card reader)
Audio in left (AVS)
Audio in right (AVS)
Video in (AVS)
S-VHS connection (AVS)
(e.g. for camcorder)
Headphones connection
Common Interface 1
(CI-Slot 1)
Common Interface 2
(CI-Slot 2)
ANT2
Antenna/cable
analogue/digital
(Tuner 2)
ANT SAT
Satellite antenna
(Sat tuner 1)
AUDIO OUT L/R - audio output left right (analogue)
mains switch
AUDIO IN1 L/R - audio input left/right (analogue)
AUDIO IN1 C - centre audio input (analogue)
SD/HD-COMPONENT IN Cb/Pb–Cr/Pr–Y - component video inputs
AUDIO DIGITAL IN - digital audio input
AUDIO LINK - surround audio outputs (analogue)
CONTROL - rotating stand control
RS-232C - serial interface
220-240V~ 50/60Hz
mains connection
ANT OUT
Connect antenna
output with ANT-TV
(tuner 1)
ANT SAT2
Satellite antenna
(Sat tuner 2)
- AV1
Euro-AV
socket 1
ANT-TV
Antenna/cable
analogue/digital
(Tuner 1)
AV2 (RGB)
Euro-AV
socket 2
Speakers Left (+/-) - Speakers Left (+/-)
Speakers Right (+/-) - Speakers Right (+/-)
SERVICE - service socket
AUDIO IN2 - audio input (analogue)
HDMI2 - HDMI (DVI) input 2
HDMI1 - HDMI (DVI) input 1
PC IN - VGA/XGA input
USB - USB connection 2 (USB stick/card reader)
AUDIO DIGITAL OUT - digital audio output
Welcome
Thank you!
About this operating manual
At Loewe, we combine the highest standards of technology, design and
user friendliness. This applies equally for TV, video and accessories.
For many questions concerning the technology you will find an answer
in the index of your TV set. If your question concerns TV set operation,
you can access a function directly from the index of the TV set. Owing to
this possibility, this operating manual only explains the most important
operating steps.
The index/glossary from page 70 onwards gives explanations of certain
terms used in the TV set and the operating manual.
Paragraphs which begin with the symbol ➠ indicate important instructions, tips or conditions for the following settings.
Terms which you will find in the menus or printed on the remote control
or TV set are written in bold type.
The necessary control elements are shown in the descriptions to the left
of the text containing the instructions for action.
Depending on the connected accessory equipment the menus in the TV
set can differ from those described here.
All the station names, programme contents, the illustrated photos, titles,
albums and album covers in this operating manual are examples.
Your new TV set is equipped for the TV standard "HDTV"
(High Definition Television). With its high definition
screen, the 100 Hz image refresh frequency and the
future-oriented digital interfaces HDMI (High Definition
Multimedia Interface) it offers possibilities for watching
HDTV broadcasts in an excellent picture quality.
HDTV is a worldwide, digital standard in the 16:9 format
which revolutionises normal TV viewing. It is broadcast
with an up to five times greater resolution than conventional signals and therefore creates an unexpectedly 3D
image.
The TV set is equipped for digital reception. You can use the already
frequently broadcast "everywhere television" (DVB-T) as well as digital
cable (DVB-C) and digital satellite reception (DVB-S).
The Loewe Digital+ HD 100 platform even allows dual reception of DVB-T,
DVB-C and DVB-S (if MHEG-5 is selected for location of TV set UK or IRL,
DVB-C and DVB-S reception is not possible, see also on page 13).
The TV set is equipped with a Dolby Digital Decoder. You can connect
a speaker system (e.g. Loewe Individual Sound) or active speakers and
enjoy movie theater sound.
You can connect a card reader or a USB stick with digital photos and/or
MP3 music files to the USB connection of your TV set and view your photos or play music via the integrated PhotoViewer/MusicBox software.
All the functions can be operated with the Loewe remote control.
We have designed the TV set in such a manner that you can easily
operate it with the help of wizards and menus. Information about the
menu settings is displayed automatically. You will quickly comprehend
the context.
®
®
®
T
C
S
Scope of delivery
•
•
•
•
•
•
•
LCD TV set
Mains cable
Antenna cable
Wall mount WM54 (incl. installation instructions)
Remote control Assist with two batteries
Operating instructions of the Digital Recorder
This operating manual
No speakers are included in the scope of delivery for the "Individual
Compose" TV set. You can custom configure the speaker equipment
with your TV set and adapt it to your requirements. Ask your dealer in
this regard.
TV set equipment
See the rating plate on the rear of the set for the precise product designation. The precise features are listed in the Integrated features item in
the index of the TV set (see page 16).
Trademarks
Manufactured under licence from Dolby Laboratories. "Dolby", "Pro Logic"
and the double-D symbol are trademarks of Dolby Laboratories.
Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674;
5,974,380; 5,978,762; 6,487,535 & other U.S. and worldwide patents
issued & pending. DTS and DTS Digital Surround are registered trademarks
and the DTS logos and Symbol are trademarks of DTS, Inc. © 1996-2007
DTS, Inc. All Rights Reserved.
VIRTUAL SPEAKER
The screen font "LoeweL2700" is based on the "Tavmjong Bah Arev
(tavmjong.free.fr)" font, which in turn is based on "Bitstream Vera".
Bitstream Vera is a trademark of Bitstream Inc.
This set contains a software which is based partly on the work of the
Independent JPEG Group.
Acknowledgements
Loewe Opta GmbH
Industriestraße 11
D-96317 Kronach
www.loewe.de
Printed in Germany
Date of issue 08/08-6.0 TB/FP
© Loewe Opta GmbH, Kronach
ID: 6.8.0 / 5.19.0
All rights including translation, technical modifications and errors reserved.
7-
Welcome
Operating convenience with wizards
This TV set offers user prompting with wizards that take you through the
settings step-by-step.
You can return to the previous step or exit the wizard at any time.
The wizards in overview
Initial installation
The initial installation wizard helps you with the initial installation and
connection of any existing equipment (see page 12).
Setting up the antenna
You enter in the antenna wizard which antenna signals are available to
you. The antenna wizard is called in initial installation (see page 12). You
can also call the antenna wizard in the TV menu under Connections →
Antenna DVB → Antenna DVB-S or Antenna DVB-T.
Search wizard
If you want to search for new stations after the initial installation, or if you
have set up your antenna for the first time, then you can handle this task
with the help of the search wizard (see page 24). You will find the search
wizard in the TV menu under Settings → Stations → Search wizard.
Connecting external devices
The connection wizard ensures that all devices are correctly registered
and connected. It is started automatically at the end of the initial installation wizard but can also be called separately (see page 40). You will
find the connection wizard in the TV menu under Connections → New
devices/modifications.
Connecting sound components
The sound component wizard ensures that the components which reproduce the TV sound are correctly registered, connected and set. It is
started automatically at the end of the initial installation wizard but can
also be called separately (see page 47). You will find the sound components
wizard in the TV menu under Connections → Sound components.
Assist+
You can select the most important operating modes directly with the
Assist+ menu (ASSIST button). Selectable modes are: TV, Radio digital,
Teletext, DR archive, PhotoViewer, MusicBox, CA module and Index (see
page 16).
- Programming and managing recordings
The recording wizard helps you to programme a video recording with a
video recorder, DVD recorder, or the integrated Digital Recorder (see page
54).
Station list
The station list is a list of all stored stations. You can also use the station
list for switching stations conveniently (see page 18).
Software update wizard
The latest software for your TV set can be loaded via DVB stations or via
USB stick (see page 36).
Info display and TV index
An information display for each menu item
The info display automatically shows content-based info texts in the
upper part of the screen for each menu item. It forms a convenient
operating system with the index (see page 15).
An index in the TV set
The index gives you an overview of the functional scope of your TV set. You
can also start wizards and menu settings directly from here (see page 16).
You can select your language for operating the TV set.
Index
Language
Integrated features
Repeat initial installation
*
Access code
ASSIST+
Automatic dimmer
Automatic station programming
OK Activate
a - z
Select letter
OK
END
Previous/next letter
P+
P–
Page ↓↑
For your safety
For your own safety and to prevent unnecessary damage to your device,
read and comply with the following safety instructions:
Proper use and environmental conditions
This TV set is designed exclusively for reception and reproduction of
video and audio signals and is designed for living rooms or office facilities,
and should not be operated in rooms with high humidity, such as a
bathroom, or sauna, or where there is a high concentration of dust (e.g.
workshops). The manufacturer‘s warranty is only valid for use in the specified
permissible environment.
If the set is used outdoors ensure that it is protected against moisture
(rain, splashing water, or dew). High humidity and dust concentrations
cause leak currents in the device, which can cause a shock hazard if the
device is touched, or a fire.
If you have brought the set into a
warm environment from the cold,
then wait for about 1 hour before
switching it on to avoid formation
of condensation.
Power supply
The wrong voltage can damage the set. This equipment must only be
connected to a mains power supply which has the same voltage and
frequency as that specified on the rating plate; use the mains cable
provided. The mains plug of the TV set must be easily accessible so that
the device can be disconnected from the mains at any time. When you
unplug the mains plug, do not pull on the cable rather pull on the plug
housing. The cable in the mains plug could be damaged and cause a
short circuit the next time it is plugged in.
Lay out the mains cable in such a manner that it cannot be damaged.
The mains cable must not be kinked or laid over sharp edges, stepped
on or exposed to chemicals; The latter also applies for the entire equipment. A mains cable with damaged insulation can cause electrical shock
and is a fire hazard.
Air circulation and high temperatures
The vent slots on the rear panel of the set must always be kept free.
Please do not place newspapers or cloths on/over the TV.
Do not place any objects filled
with liquid or burning candles on
the device. Protect the set against
dripping and splashing water.
Ensure that there is at least 10
cm free space on the sides and
above the set for air circulation,
if the set is placed in a cabinet
or on a shelf.
Never place the TV set in a position
where it is exposed to vibrations.
This can lead to material overload.
Like any electronic device, your
TV set requires air for cooling.
Obstruction of the air circulation can cause fires.
Transporting
The set is suitable for different
installation solutions. See the
instructions for assembly for the different installation solutions.
Only transport the device in vertical position. Grasp the device on the
upper and lower edges of the housing. Never set the TV down on the
protruding control unit on the bottom of the TV set. This could damage
the control unit.
If the set has to be put down during packing/unpacking, place the TV
set with the entire front surface lying flat on a soft underlay such as a
blanket or the felt from the packing material.
The LCD screen is made of glass or plastic and can break if not handled
properly.
If the LCD screen is damaged and liquid crystal escapes, wear rubber
gloves when moving the device. In the case of skin contact immediately
wash thoroughly with water.
10 cm
10 cm
10 cm
Stand the TV set with the table or floor stand only on a level, sturdy,
horizontal base. Particularly ensure that the set does not protrude to the
front when placed in or on pieces of furniture.
Set up the device where it is not exposed to direct sunlight and where it
is not exposed to additional warming through heating elements.
Prevent metal items, needles, paper clips, liquids, wax, or similar items,
from getting into the interior of the device through the vent slots in the
rear panel. Such objects can cause short circuits in the set, which could
possibly cause a fire.
If something should get into the interior of the set then immediately
unplug the mains plug of the device and contact customer service for
more information.
-
For your safety
Environmental protection
Repairs and accessories
Energy consumption
Your TV set is equipped with an eco-standby power supply. In the standby
mode, the power consumption drops to low power (see Technical data on
page 67). If you want to save even more energy then switch the device
off with the mains switch. However note that in this case, EPG (Electronic
Programme Guide) data will be lost, and it may be that programmed
timer recordings cannot be executed via the TV device.
If you activate the automatic dimming (see page 21), your TV picture will
adapt to the ambient brightness. This reduces the power consumption
of the TV set.
Never remove the back of the TV set yourself. Only have your TV device
repaired or serviced by authorised television technicians.
Only use original accessories such as Loewe stands if possible (see Accessories on pages 68 and 69).
Supervision
Do not allow children to use the TV set without supervision or to play in
the immediate vicinity of the TV set. The set could tip over, be pushed
off or pulled down from the stand surface and injure someone.
Do not allow the switched-on TV set to run unattended.
Volume
Loud music can lead to ear damage. Avoid extreme volume especially
over long periods and when using headphones.
Cleaning
Clean the TV set, the screen, and the remote control unit with a soft,
moist, and clean cloth,only, without any aggressive or scouring cleaning
agents.
Packaging and box
You have made a decision to purchase a high-quality technical product
with a long service life. For disposal of the packaging, in accordance with
national legislation we have paid a fee to a commissioned recycler to pick
up the packaging from the dealer. Nevertheless we recommend keeping
the original box and packaging material on hand so that the device can
be transported with optimal protection if necessary.
The set
Pull out the mains plug and all connected antenna cables from the TV
set in a thunderstorm. Overvoltage caused by lightning can damage the
set via the antenna system, as well as via the mains. The mains plug and
all connected antenna cables should also be pulled out during long periods of absence.
The EU directive 2002/96/EC regulates the proper way
to recycle, handle and utilise used electronic devices.
Old electronic devices consequently must be disposed of
separately. Please do not dispose of this device in normal
household trash!
You may return your used set free of charge at designated
recycling centres or at your specialist dealer whenever you purchase a
new, comparable set. Additional details about return (also for non EU
countries) are available from your local municipal authorities.
Note on the LCD screen
Batteries
Thunder storms
The TV set you have purchased with LCD screen satisfies the most rigorous quality requirements and has been inspected relative to pixel errors.
In spite of the utmost care in manufacturing the display, for technical
reasons the possibility that some pixels will have defects cannot be 100%
excluded. Please understand that these types of effects, as long as they
are within the standard of specified limits, cannot be considered as a
device defect in terms of the guarantee.
- 10
The batteries supplied as initial equipment do not contain
any pollutants such as cadmium, lead, or mercury.
Used batteries should no longer be disposed of in the domestic waste according to the Battery Ordinance. Dispose
of your batteries at no charge in the collection containers
which are set up for this purpose in retail stores.
Initial installation
Installing the TV set
Connecting the TV set
First prepare the chosen installation solution for your TV set. See the
installation instructions of the wallmount supplied. See Accessories (page
69) for other installation possibilities.
Connecting to the mains
Preparing the remote control unit
Remove the cover for the connections.
Inserting or replacing batteries
Press the embossed arrow and push down the
battery compartment cover.
Insert two alkaline manganese LR 03 (AAA) batteries;
ensure that the + and – poles are correctly positioned!
Slide the cover up from below.
3
R0
A
L
AA
LR
A
03
AA
➠N
ote the position of the mains connection in
Individual Compose 40 / 46 / 52.
Connect the TV set to a 220-240V outlet:
First plug the small plug of the mains cable into the
mains connection on the rear of the TV, then plug the
large plug into a mains power outlet.
Connecting the antenna
Analogue / DVB-C / DVB-T antenna:
Plug the antenna plug of antenna system, cable system,
or room antenna into the ANT2 socket.
The connecting cable between ANT-TV – ANT OUT is
plugged at the factory.
Satellite antenna:
Connect an antenna plug, e.g. from the antenna changeover switch or from the twin-LNC of the satellite system
to the sockets ANT-SAT resp. ANT-SAT2.
When connecting only one SAT antenna cable, connect
it to ANT-SAT.
Individual Compose: 40 / 46/52
ANT2
Adjusting the remote control for operating the TV set
Press the TV button.
See page 62 to learn about operating other Loewe
devices.
ANT
SAT
ANT
SAT2
220-240V~
50/60Hz
TV
R
Connections on the back of the set (see also page 5 and 6).
Replace the cover over the connections.
Connecting speakers
How to configure and connect TV speakers, speaker
systems or active speakers is described from page 47.
Receiving coded stations
When using a CA module and a Smart-Card to receive
coded stations, please observe the handling of the CA
module (see page 35).
11 -
Initial installation
Turning the set on/off
First installation wizard
Switching the TV set to standby mode
First installation after switching on for the first time
This wizard starts automatically after the set is switched on for the first
time, however it can also be called later manually in the TV index, see
Repeat initial installation on page 16.
Activate the mains switch on the bottom left of the set.
The display in the control panel on the front of the set
will be illuminated red, the set is now in standby mode.
Switching the TV on/off on the control unit
Press the on/off button in the middle for about 2 seconds
to switch the TV set on/off.
Display
Meaning of the display colour:
Red: Standby mode
Green: TV set is switched on
Orange:Radio mode, TV set receives EPG data or timer
recording active
First installation wizard
Which language do you want to use for operation?
Initial installation
Language
Sprache
D
Language GB
Langue
F
Lingua
I
Idioma
E
Taal
NL
Jazyk
CZ
Γλώσσα
GR
Język
PL
Nyelv
H
OK
Switching the set on with the remote control
Press the on/off button
or
numeric buttons (0–99)
or
TV button
or
OK button – station list is called
or
ASSIST button – Assist+ menu is called.
Switching the set off with the remote control
Press the on/off button.
➠B
efore switching off the set with the mains switch, we
recommend you to switch it to standby mode.
Switch on in Radio mode
Press R on the TV control unit.
or:
Press the RADIO button on the remote control
(radio mode, see page 34).
- 12
OK
Kieli
Jezik
Jazyk
Lisan
Språk
Sprog
Idioma
Язык
Språk
FIN
SLO
SK
TR
S
DK
P
RUS
N
Proceed
The first step with the wizard starts when selecting the
language for the user prompts. From this point on follow
the instructions on your TV set.
Brief explanation of button functions:
Press the ring (up, down, left, right) to move the cursor
and to select settings.
By pressing the OK button a setting is confirmed and you
will go to the next step.
With the yellow button you can select or remove the individual items (see the example below).
When an element is selected, it is marked by a checkmark .
Use this button to go back one step.
Exit the wizard with the END button (if available).
Initial installation
Connect antenna cable(s)
Antenna cable(s) for:
Antenna/cable (analogue)
DVB-T
DVB-C
DVB-S (cable 1)
DVB-S (cable 2)
OK Proceed
to antenna socket(s):
ANT TV

ANT TV

ANT TV
ANT SAT

ANT SAT2
Connect/disconnect
Back
An example of multiple selection using the yellow button.
continued on the next page
Ž
Initial installation
Explanations of the setting possibilities:
Location Select the country for country-specific pre-settings.
of TV set If UK or IRL is selected for the location of TV set, it is possible to activate MHEG-5 (UK Freeview) for the TV set.
A dialogue appears, where you can confirm to set the
operating software to the selected location.
If Yes is selected and confirmed with OK, the TV set turns
off and on again automatically. First installation starts
again after activating the operation software.
If MHEG-5 was activated, DVB-C and DVB-S can not be
used anymore. Only terrestrial/cable and DVB-T stations
are available.
Antenna Antenna/cable (analogue): analogue stations via
cable/antenna
selection DVB-T:
digital terrestrial stations
DVB-C:
digital stations via cable
DVB-S (cable 1):
digital stations via satellite
DVB-S (cable 2):
digital stations via satellite
Encrypted You can state whether coded stations are to be searched
stations for in the search/update. Select yes then coded stations
are also searched for. However, these stations can only
be received in connection with a CA module and the
appropriate Smart Card. Handling of the CA module is
described on page 35.
DVB-T: If you are using an active antenna, then select yes (5V)
Antenna for the antenna power supply.
DVB-C: The conventional settings will be derived from the selection
Settings of set location. Only change this if you know other symbol
rates and modulation types or if you have to specify the
network ID for your cable network (information available
from your cable network provider). If you want to run the
station search independently of the channel grid, select
frequency search for the search method.
DVB-S: Select which satellite(s) you receive from a list. For more
Satellite than one satellite, select the type of your changeover
system switch or communal satellite system additionally.
Ask your dealer in this regard.
High band Specify here whether the high band of the selected satellite
is to be searched in addition to the low band.
LNC
frequencies
Low Band /
High Band
Normally, you do not need to change the values for high
and low band, unless the LNC (LNB) of your satellite
system uses a different oscillator frequency (important
for the frequency display).
After you have made these settings, you should receive
the picture and sound of the selected satellites (only with
Astra1 and HOTBIRD).
Search If you want to run the station search independently of
method the channel grid, select frequency search for the search
method.
Symbol rates The symbol rates are specified by the satellite provider
and normally do not need to be changed.
Favoured Select the signal source that provides the stations to be on
signal source top of your station list (starting with station slot 1).
Start search Start the automatic station search with OK.
First TV stations, then radio stations are searched for.
The stations found in the automatic search are divided
into the appropriate station blocks depending on the
previously selected antenna cables (signal sources). Subsequently the stations can only be re-sorted within these
blocks. At the beginning of the station list you will find the
block with the stations of the preferred signal source.
Any mixed sorting of stations from different signal sources
is only possible with the favourites list.
➠ F or TV sets with MHEG-5 software the stations are
tied to “Logical Channel Numbers” – “LCN” and
sorted from 1-799. Digital stations without “LCN” are
stored from 800 onwards. Analogue stations are stored
from 1001.
Connecting Then the connection and sound component wizard
additional starts which helps you to log in, set and connect video
devices recorders, decoders, a loudspeaker system or a HiFi/AV
amplifier to your TV set. DVD players and DVD recorders
are already registered at the factory.
You can start the connection wizard and the sound
components wizard manually later and add new devices.
Further information is available from page 40 (Connection
wizard) and page 47 (Sound components wizard).
continued on next page
Ž
13 -
Initial installation
Digital Link If you have registered and connected a recorder in the
Plus connection wizard, the Digital Link Plus transmission
begins at the end of the sound components wizard. If
a Digital Link Plus capable recorder is connected, the
station list of the analogue stations is transmitted to the
external recorder.
You can also call Digital Link Plus under TV menu → Connections → Digital Link Plus.
Positioning/aligning DVB-T antenna
If you are receiving one or more DVB-T stations with picture and sound
interference then you should change the installation location and alignment of the antenna. Ask your dealer to tell you which channels are used
to broadcast the DVB-T stations in your region.
➠ In normal TV mode, without other displays. A DVB-T station is received and selected.
Call TV menu.
Explanations of the DVB-T antenna:
Room With good reception conditions a room antenna can be
antenna used for DVB-T (socket ANT2).
Active Under less favourable reception conditions, it is advisable
antenna to use an active antenna which has to be set accordingly
in the initial installation or in the TV menu → Connections
→ Antenna DVB → Antenna DVB-T (see DVB-T antenna
on page 13).
Directional If the location is outside of the normal transmission
antenna range then a directional antenna can be used to improve
reception quality.
34Select Settings,
6go to the menu line below.
34Select Stations,
6go to the menu line below.
34Select Manual adjustment,
OK call manual adjustment.
Signal source
Select the area in which you want the broadcaster to search here. You can
use the
button to automatically select station by station.
Manual adjustment
SIgnal source
Channel
Frequency
Bandwidth
Name
C/N
Level
BER
DVB-T
E05
177.50 MHz
7 MHz
12 Test
81
80
0 E-7
DVB-C
DVB-S
A
END
Overwrite station
Search
INFO
The signal source is already on DVB-T due to the station
preselection.
Position and align the antenna in such a manner that
maximum values for C/N and Level are obtained.
Blue button: Start search.
Search for DVB-T stations one after another and compare
values for C/N and Level.
Then position/align the antenna to the weakest station
so that maximum values for C/N and Level are obtained.
Thereafter perform an automatic search for all DVB-T
stations, see page 24.
Explanation of the setting possibilities:
Bandwidth Depending on the selected channel and country the
associated bandwidth of 7 or 8 MHz will be set automatically.
- 14
Operating convenience
General information on menu operation
The info display
Menus for the individual operating modes (TV, Radio, PIP, EPG, Teletext,
PhotoViewer, MusicBox and DR archive) are called with the MENU button.
Other menus can be opened with other buttons on the remote control.
The menus are displayed at the bottom of the screen. At the top you get
additional information about the selected menu item (see info display on
the right).
The info display shows a content-based info text for each menu item at
the top edge of the screen to aid you in making the settings. In conjunction with the index it makes a convenient control system.
➠ In normal TV mode, without other displays.
Call TV menu.
Picture
Here you can adjust among other things: Contrast, colour, brightness, picture
adjustment, sharpness, picture format.
➠ A menu is displayed.
The factory setting is that the info display is shown automatically for each menu item. In this case you can temporarily hide the info texts with the INFO button.
The automatic info display can be hidden via a menu
setting. Then it can be displayed temporarily by pressing
the INFO button.
Settings
Here, you can search for stations automatically or manually as well as set the
menu language, timer functions, parental lock, on-screen displays, etc.
TV menu
Picture
Picture adjustment
INFO
...
Sound
Recording
Connections
END
Settings
Example: Selecting and executing functions
34Select Picture,
6go to the menu line below.
34Select Brightness,
6go to the menu line below.
34Set Brightness.

Return to the Brightness menu line to make other picture settings.
34Select more ... ,
OK call more ... functions.
34Select Auto format,
6go to the menu line below.
34Select on / off.
Conclude the settings.
Inputs with the numeric buttons
Letters have to be entered for specific functions. Like using
a mobile phone keypad (1 to 9), press a numeric button
until the desired character appears.
The available letters are printed on the individual numeric
buttons.
Connections
TV menu
Settings
Stations
INFO
...
Picture
Sound
Recording
END
Connections
An INFO icon at the bottom right above the menu bar
also tells you that an info text is available.
If a several page info text is available, Page↓↑ is displayed
in the info window and you can scroll through the individual info pages with P+ and P–.
Permanently display or hide the automatic info display
Once you have become familiar with how to operate the TV set, you can
switch off the automatic info display.
➠ In normal TV mode, without other displays.
Call TV menu.
34Select Settings,
6go to the menu line below.
34Select Miscellaneous,
6go to the menu line below.
34Select On-screen displays,
6go to the menu line below.
34Select Automatic info,
6go to the menu line below: yes / no.
15 -
Operating convenience
The index in the TV set
The Assist+ menu
You can start all wizards and many operating functions directly from
this point. The complete function scope of the TV set can thus be easily
understood.
Alphabetic sorting is preceded by the items Language, Integrated features
and Repeat initial installation.
The most important additional functions of the TV set can be called
directly with the Assist+ menu.
Open Assist+
Call Assist+ menu.
56Select additional function,
OK calls the function.
Call index
➠ In normal TV mode, without other displays.
Call Index.
You will see an info text for the highlighted keyword in
the info display. If MHEG-5 is active, call the status display
with INFO and press INFO again for index.
Assist+
TV
Radio digital
Teletext
DR archive
You can select your language for operating the TV set.
PhotoViewer
OK
Your personal photo selection
MusicBox
CA module
Index
Index
Language
Integrated features
Repeat initial installation
*
Access code
ASSIST+
Automatic dimmer
Automatic station programming
OK Activate
a - z
Select letter
END
OK
Description of the individual functions:
END
Previous/next letter
P+
P–
Page ↓↑
If an OK symbol appears in the marked line, this function
can be called directly with OK.
TV:
See page 18 onwards.
Radio digital:
See page 34.
Teletext:
See page 32 onwards.
DR archive: See Digital Recorder operating instructions.
Selecting a keyword
Enter initial letters with the numeric buttons like with a
mobile phone keypad (see page 15).
or go with:
34to the preceding / next letters,
65from line to line,
P+/P– scroll backwards or forwards in whole pages.
- 16
Example: You want to have the TV set switch off automatically at
a specific time:
Select the keyword Switch off → Automatic, with OK you
will go to the setting.
PhotoViewer: See page 56 onwards.
MusicBox:
See page 58 onwards.
CA module: Menu item only appears if a CA module
is plugged (see page 35) and a digital
station is selected.
Index:
See left-hand column.
Operating convenience
TV menu – Overview diagram
TV menu
Picture adjustment
Contrast
Colour intensity
Colour temperature
Brightness
Sharpness
Digital Noise Control (DNC)
more...
Image+
Picture format
Move picture up/down (3
Auto format
Film quality improvement (DMM)
Automatic dimmer
Recording (7
Sound
Picture
Sound mode
Dolby PLII mode (9
Sound adjustment
Headphone volume
Loudness
more...
Recording wizard
Timer list
Pre-record time
Post record time
(1
New devices/modifications
Sound components (1
Antenna DVB (1
Digital Link Plus
Miscellaneous
Auto volume
Maximum volume
Switch on volume
Volume adjustment for
current station
Balance
Search wizard (1
Manual adjustment
Change stations
Select/change favourites
Search wizard (1
Manual adjustment
Change stations
Select/change favourites
Parental lock
Timer functions
Switch off times (4
Alarm times (4
Wake up with
Wake up signal volume
Language
Menu
Subtitles (DVB)
Audio (DVB)
On-screen displays
Time and date
Software update (1
CA module: xxx (5 (8
DVB settings
Rotate TV (6
Radio menu
Sound mode
Dolby PLII mode (9
Headphone volume
Loudness
more...
Stations
Miscellaneous
Radio menu – Overview diagram
Stations
(1
Manual adjustment of
AV standard
Assign digital audio input
Allow switching voltage
RGB insertion at AV2
Remote TV switch on via Digital
Link HD
Loudspeaker sound (2
Headphone sound (2
Auto volume
AV output signal
Maximum volume
Switch on volume
Volume adjustment for
current station
Balance
Sound
Settings
Connections
Timer functions
Switch off times (4
Alarm times (4
Wake up with
Wake up signal volume
A wizard is started here.
Menu items only appear for analogue stations.
(3
Menu item only appears with certain picture formats (see page 22).
(4
List of individual menu items.
(5
Menu item only appears if a CA module is plugged in (see page 35).
(6
Menu item only appears when, for example, a stand with motor drive (see Accessories, Installation possibilities, page 69) is used.
(7
Menu item only appears in sets with DR+ or with logged in external recorder.
(8
Menu item does not appear for analogue stations.
(9
Menu item only appears with certain sound mode settings.
(1
(2
17 -
Daily operation
Select station
With the station list
➠ In normal TV operation, without further displays, no
favourites selected:
With the keys P+ and P– on the remote control
P+/P– Station up/down.
The station display with sound identification is displayed
briefly.
➠ If favourites are selected, the station is switched over
in the favourites list with P+/P– (see page 19).
➠ T he symbols for the sound identification are described
on page 23.
➠ If there are additional languages or DVB subtitles for
DVB stations, then language and subtitle selection is
shown below the station display.
See also page 23: Additional selection possibilities for
DVB stations.
OK Call Station list.
Sorting
numerically
short short long
COMP. IN
HDMI1/DVI
HDMI2/DVI
VGA
AVS
DVD
VCR
0 VIDEO
1 Das Erste
2 ZDF
3 WDR Köln
OK
P+
P–
Page ↑↓
0
-
9
Switch to ...
Select station
Favourites
78 Jump to the next station block.
2-digit and 3-digit stations
Press first (and second) numeric button briefly.
Keep the last numeric button pressed for one second, the
station changes immediately.
or:
Press all the numeric buttons briefly, the station changes
after 2 seconds (changes immediately in case of up to 99
or 999 stored stations).
OK The marked station is called.
➠ If favourites are selected, the station in the favourites list
is switched to with the numeric buttons (see page 19).
Maximum two-digit station numbers are possible.
➠ If you select an unoccupied station slot, the next available station is switched to.
56You can switch back and forth quickly between
two stations using this buttons.












Scan stations
Change stations
Sort alphabetically
1-digit stations
Keep the numeric button pressed for one second, the
station changes immediately.
or:
Press the numeric button briefly, the station changes after
2 seconds (changes immediately in case up to 9 stations
are stored).
Call last viewed station (for TV sets with MHEG-5 software)
- 18
OK
Bayerisches FS
hr-fernsehen
Phoenix
BR-alpha
3sat
EinsExtra
EinsFestival
EinsPlus
ZDFinfokanal
ZDFdokukanal
ZDFtheaterkan
arte
END
INFO
P+/P– Scroll in the pages of the station list.
5634 Mark stations.
or:
Enter the number of the station with the numeric buttons.
The marked station is shown as a small picture.
Blue button: Changes the sorting between numerically
and alphabetically.
Sorting
alphabetically
.
Station list
4-digit stations
Press all four numeric buttons, the station changes immediately.
all short



4
5
6
7
8
9
10
11
12
13
14
15
21:00 - 21:45 Urlaubsparadies - Toskana
With the numeric keys of the remote control
long
Station list
3sat
9Live


arte
ARD
AVS


Bayrisches FS
BR-alpha
BR


CNN INT
P+
P–
Page ↑↓
COMP IN
Das Erste
DSF
DVD
DVD-REC


EinsExtra
EinsFestival
EinsPlus
Eurosport




21:00 - 21:45 Urlaubsparadies - Toskana
OK Switch to ...
Scan stations
a - z Select letter
Change stations
Favourites
Sort numerically
OK
END
INFO
Enter initial letters with the numeric buttons like with a
mobile phone keypad (see page 15).
The first station for the specified letters is marked.
5634Mark stations.
OK The marked station is called.
Daily operation
With the favourites lists
Select video source
You can save and call your favourite stations in 6 favourites lists (e.g. for
multiple users). Each favourites list can contain up to 99 stations. After
initial installation, 10 stations from the station list are already stored in
the first list. Change the favourites list to suit your requirements (see Put
together / change favourites lists on page 27).
➠ Please ensure that the appropriate devices have also been registered
with the connection wizard (see page 40).
➠ In normal TV mode, without other displays:
With the AV selection
Call AV selection.
OK calls the station list.
AV selection
COMP. IN
HDMI2/DVI
HDMI1/DVI
PC IN
AVS
DVD-REC
DVD
VIDEO
OK Switch to ...
Red button: Calls the favourites list.
Favourites
Favourite list1
1 Das Erste
2 ZDF
3 WDR Köln
4 Bayrisches FS
5 hr-fernsehen
6 Phoenix
7 BR-alpha
8 3sat
9 EinsPlus
10 EinsExtra
11 MTV
12 VIVA
0
-
9
P+
P–
Select station
Page ↑↓
OK












OK
Switch to ...
Station list
OK
END
56Select desired device or connection,
OK switch over.
Scan stations
Change favourites
END
INFO
Select station directly with numeric buttons. Or:
A signal from the selected video source should now be
visible.
With the station list
56Mark stations.
➠ In normal TV mode, without other displays:
P+/P– Scroll in the pages of the favourites list.
OKCall the station list.
If the favourites list is displayed, switch to the
station list first.
34Select other favourites list.
➠O
ther favourites lists can only be selected if these
contain stations.
OK The marked station is called.
Red button: Back to the station list.
Green button: Scan all stations of the currently selected
favourites list.
Yellow button:Change the Favourites lists, see page 27.
In numerical sorting the connections or devices are always
at the beginning of the list.
In alphabetic sorting, the connections or devices are
sorted in alphabetically.
Station list
COMP. IN
HDMI1/DVI
HDMI2/DVI
VGA
AVS
DVD
VCR
0 VIDEO
Explanation of the favourites lists:
The selection made with the red button (favourites list) is retained until
you switch back to the station list with the red button.
If favourites are selected, the name of the favourites list appears in the
status display after the station name after changing stations.
Explanation of the icons following station names:
 Digital DVB-T station (terrestrial via antenna)
 Digital DVB-C station (via cable)
 Digital DVB-S station (via satellite)
 Coded station
1 Das Erste
2 ZDF
3 WDR Köln
OK
P+
P–
Page ↑↓
0
-
9




Switch to ...
Select station
Favourites
OK
4
5
6
7
8
9
10
11
12
13
14
15
Bayerisches FS
hr-fernsehen
Phoenix
BR-alpha
3sat
EinsExtra
EinsFestival
EinsPlus
ZDFinfokanal
ZDFdokukanal
ZDFtheaterkan
arte
Scan stations
Change stations
Sort alphabetically












END
INFO
634 Select connection/device.
5
OK Switch over.
19 -
Daily operation
Adjusting the sound
Explanations of the sound settings:
Switching sound off/on
Sound off;
Sound on: Press button again or set volume V+.
Setting the volume
V+/V– Volume louder / quieter.
The volume bar will be shown briefly if no other menu
is displayed.
Setting the sound mode
Call Sound mode.
Sound mode
optimal
...
(5)
4
3
2
1
34Select the number of speakers you want to hear.
Additional sound settings for volume adjustment and for Sound mode:
➠ As long as you can still see the volume bar or the
selection of speakers for sound mode:
5Call additional sound settings.
END
Volume
24
Sound mode
DPLII mode
Sound adjustment
34Select sound setting,
6 go to the menu line below.
34Make changes.
Sound settings via the TV menu
➠ In normal TV mode, without other displays.
Call TV menu.
34Select Sound,
6go to the menu line below.
34Select desired sound setting,
6 go to the menu line below.
34Make changes.
- 20
Sound mode Select the number of speakers you want to hear. The
selection depends on the connected sound components
(from page 47) and on the transmitted audio signal.
➠ If the number of speakers appears in brackets, the
sound of missing speakers is transmitted by the existing
speakers (virtual).
optimal The momentarily reproduced audio signal is output with
the ideal number of speakers.
1 Play centre sound or mono (left/right).
2 Play front sound (L/R stereo).
3 Play front and centre sound.
4 Play front and surround sound.
5 Play front, surround and centre sound.
Amplifier Play via an external HiFi amplifier. Selection is only possible
if an amplifier has been selected in the sound components
wizard (see page 52).
Sound Speech, Classical, Pop, Custom music, and Custom film
adjustment sound.
Headphone vol. Adjust the headphones volume.
Loudness Proper boost of bass and treble tones at low volume.
Dolby PLII Here you can make Dolby Pro Logic II sound settings for
mode movie, music, matrix and personal settings. Menu item
only appears with certain sound mode settings.
more ... Call with OK.
Loudspeaker/ Selection possibility Mono/Stereo or Sound 1 or Sound
Headphone 2 for two-sound broadcasts separately for speakers and
sound headphones. Only available for analogue stations.
Headphone volume
Auto Volume Reduces volume differences, e.g. for advertisements that
are too loud.
AV output Sound selection for two-sound broadcasts.
signal
Maximum Determining the maximum volume that can be set.
volume
Switch on Specify the volume that is set when switching on the TV
volume set with the mains switch.
If the volume when switching off the TV set into standby
mode is higher than specified here, it is automatically
reduced to the fixed switch-on volume when switching
back on.
Volume The volume can differ according to the individual stations.
adjustment for If the sound is too loud or too quiet in relation to other
current station stations, adjust the volume. When the menu is open, you
can select the stations one after another with P+/P– and
adjust every single station conveniently.
Balance Set stereo balance so that the volume impression is identical
on the left and right.
Picture
Here you can adjust among other things: Contrast, colour, brightness, picture
adjustment, sharpness, picture format.
Daily operation
Adjusting the picture
Picture adjustment
Here, you can switch between the preset standard values for contrast, colour
intensity, colour temperature, brightness, focus and digital noise reduction
and your own personal values. Each of the signal input groups „TV analogue“,
„TV digital“, „HD analogue“, „HD digital“, „PC“ and „PhotoViewer“ has its own
values. Refer to printed operating manual.
INFO
END
TV menu
Connections
Picture
Sound
Recording
Settings
Picture adjustment
...
TV menu
Picture (personal values, TV digital)
Picture adjustment
Standard values (TV digital)
Call TV menu.
INFO
OK
END
Personal values (TV digital)
34Select desired values for picture,
OK call selected values for picture.
34Select Picture,
6go to the menu line below.
Explanations for picture adjustment:
Custom adjustments of contrast, colour intensity, colour temperature,
TV menu
brightness, sharpness and digital noise supression are saved in the perPicture (standard values, TV digital)
Picture adjustment
Colour temperature
Contrast
Colour intensity
sonal values. There are separate personal values for every signal source
Standard values (TV digital)
...
(TV analogue, TV digital, HD analogue, HD digital, PC, PhotoViewer).
34Select the desired picture function,
By selecting Standard values the picture parameters are reset to factory
6 go to the menu line below.
values for the respective currently active signal source.
For an explanation of the signal source, see glossary: Signal input
34Make changes.
groups.
Explanations of the picture settings:
In the index of the TV set, all the picture and sound adjustments can be
reset to the factory values for all signal sources in one step under Reset
Picture Switches the picture parameters between standard and
picture/sound or Factory settings picture/sound.
adjustment personal values.
Contrast Adjust contrast.
Operation without remote control
Colour intensity Adjust the colour.
Colour Set warmer or cooler tints for the picture.
Changing the station on the TV set
temperature
Brightness Adjust the brightness of the picture.
+ / – Station up/down.
Sharpness Adjust the contour sharpness of the picture.
DNC Removes or reduces the signal noise in the picture.
INFO
more ...
Image+
Picture format
Move picture
up/down
Auto format
END
Call with OK.
Picture improvement on/off and demo mode for Image+.
Set picture format (see page 22).
Move picture vertically (see page 22).
Automatic detection and setting of the picture format
for Cinemascope or widescreen movies.
DMM Reduce jolting.
Automatic The TV picture adapts to the ambient brightness. The
dimmer power consumption of the TV set is also reduced.
Standard values / personal values for picture adjustment
Switching radio on or off or switching to radio
R Radio on or switching between TV and radio.
Calling the TV menu on the set
M call Direct control on TV set menu,
AV selection
Direct control on TV set
Volume
19
Brightness
Contrast
Picture format
Station
– / + select function.
Call TV menu.
➠ Service is for customer service personnel only.
34Select Picture,
6go to the menu line below.
M or R Go to the menu line below,
– / + make changes.
34Select Picture adjustment,
6 go to the menu line below.
M Move up one menu line,
– / + select other function.
21 -
Daily operation
Button functions
Selecting the picture format
Press the picture format button until the desired picture
format is set or press
Every operating mode of the TV set (TV, Radio, Teletext, EPG, PIP, PhotoViewer, MusicBox and DR archive) has its own menu and own functions for
the coloured buttons. The function of the coloured buttons is shown at the
bottom of the menus and wizards. Below, some of the function are listed
which you need in TV mode for the daily handling of your TV set.
34to select the desired picture format.
The Panorama picture format can be switched between
proportionally correct and format filling reproduction.
Dark margins are visible on the right and left of the picture
in proportionally correct reproduction.
Switching over: Keep the M button on the set pressed,
at the same time press the Picture format button on the
remote control briefly.
Resetting: Press the same button combination again.
Functions of the coloured buttons in TV mode
➠ T he coloured buttons do not work as described below
for TV sets with MHEG-5 software, but they operate as
described on page 33 (Digital Teletext).
Red button: Digital Recorder: DR archive on/off.
For TV sets with MHEG-5 software you can open the DR
archive via the menu Assist+ (see page 16).
Green button: Open the Teletext functions menu.
INFO
Teletext functions
Teletext subtitles
on, with normal size
...
END
Personal text pages
➠ T he setting options depend on the transmitted picture
content.
34Select Teletext subtitles or Personal text pages.
6 Go to the menu line below in Teletext subtitles.
34Select the size of the Teletext subtitles,
OK show Teletext subtitles.
(display only if subtitles are available).
END: Teletext subtitles off or select off in menu.
OK in Personal text pages calls the teletext pages or the
teletext page directly if only one page is noted (for
defining pages, see page 33).
Yellow button: Go to the last viewed station.
Use this button to quickly switch back and forth between
two stations. For MHEG-5 see page 18 or on this page at
the right lower column.
Blue button: Show programme info.
For MHEG-5, no programme info is available.
1 ARD
14:30 - 15.15
Explanations of the picture formats:
Urlaubsparadies Toskana
16:9 Proportionally correct display of 16:9 programmes.
4:3 Proportionally correct display of 4:3 programmes.
Panorama Proportionally correct or format filling reproduction
(delivery status) of 4:3 broadcasts on the 16:9 screen.
Station logos and subtitles remain visible.
See above for switching Panorama mode.
Cinema Proportionally correct, format filling display of 4:3 broadcasts on 16:9 screens. Station logo and subtitles usually
not visible.
Zoom Proportionally correct display. Maximum picture magnification.
PALplus Is a 4:3-compatible 16:9 picture broadcast supplied by
the station which is detected automatically. If a high-resolution picture signal is displayed on the TV
set or fed in via the interfaces PC IN, HDMI1/DVI, HDMI2/
DVI or COMP. IN, the picture formats 16:9 TV, 4:3 TV as
well as 16:9 PC and 4:3 PC can be set.
Move picture vertically
➠ In normal TV mode, without other displays:
56Move picture up/down.
Programme info
Detailed info
14:43
OK
END
Detailed info (teletext)
Programme preview
Permanent display of time
Press twice in rapid succession: Time is displayed permanently.
 14:42
K or END: Hide time.
- 22
To show subtitles or news tickers which have been cut
off, the picture can be moved up or down in the picture
formats Panorama, Cinema and Zoom (not with high
resolution signal) with the arrow buttons 56.
➠ F or TV sets with MHEG-5 software you can switch
back and forth quickly between two stations using
these buttons (see also on page 18).
Daily operation
Status display
➠ In normal TV mode, without other displays.
END: Show / hide status display.
For MHEG-5, INFO button.
1 Das Erste
14:30 - 15:15
Toskana
Language-/sound selection
 14:42
Alarm time 20:00
  Digital (5)
Sleep timer 23:00
You will see the number and name of the station, the title
of the current broadcast (if available) and the sound identification in the top two lines.
The bar (if available) indicates the progress of the current
programme.
A selection (see right hand column), the time and, if activated, the alarm time and switch-off time appear at the
bottom depending on the DVB station.
Explanations of the symbols for sound identification:
Mono
2-sound
Stereo
 Digital
dts
MPEG
 PLII
Transmitted audio signal:
Mono audio transmission analogue
Two-sound transmission (Sound1/Sound2) analogue
Stereo sound transmission analogue or digital (PCM)
Dolby Digital sound transmission (DD)
dts sound transmission
MPEG sound transmission
Dolby Pro Logic II sound transmission









Transmitted audio channels:
DD / dts 1.0 / mono
DD / dts / MPEG 2.0
DD / dts 3.0
DD / dts 4.0
DD / dts 5.0
DD / dts 2.1
DD / dts 3.1
DD / dts 4.1
DD / dts 5.1
1
2
3
4
5
Selected listening mode:
Play centre sound or mono (left/right).
Play front sound (L/R stereo).
Play front and centre sound.
Play front and surround sound.
Play front, surround and centre sound.
➠ If the number of speakers appears in brackets, the
sound of missing speakers is transmitted by the existing speakers (virtual). The Dolby Virtual speaker (VS
mode) developed by Dolby is activated for the virtual
sound reproduction.
Additional selection possibilities for DVB stations
In the status display additional selection possibilities can be offered for
specific programmes depending on the DVB programme provider.
➠ T he coloured buttons do not work as described below
for TV sets with MHEG-5 software, but they operate
as described on page 33 (Digital teletext).
➠ If during the status display you press one of the coloured
buttons or the TEXT button then the associated selection
menu will be displayed.
➠ T he selection line is also displayed automatically when
a new broadcast with different options to the previous
broadcast begins or when you switch stations.
The following options are possible:
Red button: Channel selection for multi-channel providers
Green button:Language/audio selection
Yellow button:Time selection
Blue button: Protection of minors
TEXT: DVB subtitles
The selection menus are only available as long as the
status display is shown. However you can call them again
by pressing the END button.
Other setting options for DVB stations
You can make general presettings for DVB stations under TV menu →
Settings → Miscellaneous → DVB settings.
Subtitle Here you can preset whether a subtitle is always to be
mode displayed as soon as it is offered by the station. A special
subtitle for impaired hearing can also be selected.
Subtitles are not offered by all stations. Many stations only
broadcast subtitles by teletext.
Audio Here you can preset whether you always want to hear a
mode special sound for impaired sight as soon as it is offered
by the station.
DVB character Select the DVB character set so that the title of the broadset cast of your favourite received station or the texts of your
CA module are displayed correctly.
23 -
Managing stations
TV stations
Explanations of some search settings:
Various options for managing stations are available via the TV menu. For
example the description for TV stations. For radio stations the same applies,
except that the radio menu is called in radio mode (see also page 34).
➠ Station management is not possible if a programmed timer recording
is still pending.
Search/update stations – Search wizard
In the search/update with the search wizard, new stations are searched
for which are not yet stored.
➠Y
ou have to repeat the initial installation (see page 12)
and automatically search for new ones if you want to
delete all the existing stations and automatically search
for new ones. Do also use the first installation if you
want to change to receiving MHEG-5 stations (attend
restrictions for DVB software update, see page 36).
Call TV menu.
34Select Settings,
6go to the menu line below.
34Select Stations,
6go to the menu line below.
In the upper info text the current search settings will now
be displayed:
Search wizard
Your TV carries out the update of the station range (search for new stations;
delete stations no longer broadcast) with the following settings:
Location of TV set
United Kingdom
Signal source
DVB-T
END
OK
Start search/update
If you want to change these search settings:
34Select Change search settings,
OKwizard prompts search settings.
If you agree with these settings:
34Select Start search/update,
OKstart search.
Red button: Abort current search/update.
- 24
Signal source Select antenna, cable, or satellite here, depending on
where you want to search for new stations.
At this point you can also call a configuration of the
DVB-T and DVB-S antennae via the green button (see
page 13).
Antenna/cable: With selection of set location the conventional TV
TV/colour standard/colour standard is the default. This should only
standard be changed if stations with other standards are to be
searched.
Encrypted You can state whether coded stations are to be searched
stations for in the search/update. Select yes then coded stations
are also searched for. However, these stations can only
be received in connection with a CA module and the appropriate Smart Card. Ask your dealer which Smart Card
you need to receive certain stations. Handling of the CA
module is described on page 35.
DVB-T If you want to run the station search independently of
Search method the channel grid, select frequency search for the search
method.
34Select Search wizard,
6go to the menu line below.
TV menu
Settings
Stations
Search wizard
Change search settings
Set location Select the country for country-specific defaults and
station sorting.
DVB-C With the selection of set location the conventional setSettings tings will be preset. Only change this if you know other
symbol rates and modulation types or if you have to
specify the network ID for your cable network (information available from your cable network provider).
If you want to run the station search independently of
the channel grid, select frequency search for the search
method.
DVB-S If you want to run the station search independently of
Settings the channel grid, select frequency search for the search
method.
The symbol rate is specified by the satellite provider and
normally does not need to be adjusted.
Managing stations
Search for/update stations – handling of new and no longer found stations
The number of new stations found is displayed after the automatic
search/update has been completed.
Search wizard
All stations marked with a  are saved.
Note: The newly found stations which you have already deleted
are not marked.
OK
P+
P–
You can enter or edit the station data in the following
lines:
OK
Mark/unmark station
Mark/unmark all
5634 Select station,
Yellow button: Mark / unmark station
Blue button: Mark / unmark all
OK saves the selected stations.
Afterwards, a list of the stations which are saved but
which are temporarily not broadcasting or no longer exist
is displayed, if available.
The number of the memory location used is displayed in
front of the station. Please select the stations you really
want to delete.
Search wizard
The following stored stations were no longer found because they are not
currently broadcasting a programme or no longer exist. Please mark those
you want to delete completely. Those not marked are retained.
OK
P+
P–
34Select Stations,
6go to the menu line below.
source
34SSignal
elect
Manual adjustment,
Select the area in which you want the broadcaster to search here. You can
OKcall
inputbutton
box.to automatically select station by station.
use the
Proceed
Page ↑↓
Search for/update station
Stations no longer found
112 S36
 
127 Test-R
 
134 TVOTEXT
 
142 ARD-Online... 
Call TV menu.
34Select Settings,
6go to the menu line below.
OK List of new stations found
Search for/update station
Newly found stations
WDR-Köln

EinsFestival
 
MDR S-ANHALT
 
Test-R
 
ARD-Online-Kanal 
ARD-TEST-2
 
ARD-TEST-1

MDR THÜRINGEN  
Search/update station – manual search
Manual adjustment
Signal source
Channel
Frequency
Name
TV stand.
Col. standard
Antenna/cable (analogue)
S21
303.25 MHz
KIKA
B/G
Autom.
Store
Search
DVB-T
DVB-C
D
END
INFO
Or:
Blue button:Starts Search and searches for next station.
Red button: Stores station.
➠O
nly stations for the selected signal source can be
saved which do not yet exist in the station list.
➠ S tations which already exist in the station list for the
selected signal source are displayed with their station
numbers and names on a grey background. These
stations can only be overwritten with the red button.
Explanations of some search settings:
Various settings are possible depending on the selected signal source.
Some settings have already been explained in the initial installation (see
page 12 onwards).
OK
Proceed
Page ↑↓
Mark/unmark station
Mark/unmark all
5634 Select station,
Yellow button: Mark / unmark station
Blue button: Mark / unmark all
OK deletes the selected station.
Signal source Selection of range in which you want to search for the
station.
Channel Direct input of channel.
Frequency Direct input of station frequency.
TV stand. Input of station TV standard.
(B/G, I, L, D/K, M, N) Ask your dealer in this regard.
Col. standard Input of the station colour standard.
(PAL, SECAM, NTSC-V, PAL60, Autom.)
Ask your dealer in this regard.
END: Exit the search wizard.
25 -
Managing stations
Rename station
Change, delete, move, rename, restore stations
➠ Change stations can also be called via the station list
(page 18).
Call TV menu.
34Select Settings,
6go to the menu line below.
Blue button: Starts Rename station.
Under the 1st letter of the name you will see a line indicating the current input position.

Input position one character to the right (also for
blanks).

Input position one character to the left (deletes the
character).
34Select Stations,
6go to the menu line below.
34Select Change stations,
OKcall list of stations.
Change stations
Here you can move stations, delete stations, restore stations you have
deleted and enter and change names of analogue stations.
Change stations
1 ARD
13 WDR 3
2 ZDF
14 BR
3 SAT.1
15 HR
4 D Vierte
16 MDR 3
5 RTL
17 KIKA
6 VOX
18 PHOENIX
7 S-RTL
19 BR-ALPHA
8 N-TV
20 3SAT
9 DSF
21 KABEL 1
10 EinsPlus
100 Das Erste

11 9Live
101 ZDF

12 RTL2
102 WDR Köln

P+
0 - 9
Restore stations
Select station
P– Page ↑↓
Move
Rename
Delete
➠N
ot possible for MHEG-5 stations.
➠D
VB stations for which the station name is also broadcast
cannot be renamed. In this case, the Rename function
is hidden.
Enter the letters one after another with the numeric
buttons on the remote control. Like using a mobile phone
keypad, press a numeric button until the desired character
appears. The available letters are printed respectively on
the buttons. Different special characters can be selected
with button 1.
Green button: Switch upper/lower case letters.
END
INFO
In this menu you can delete, move, rename or restore
stations.
3456or numeric buttons:
Select the appropriate station.
Scroll with P+/P– if necessary.
OK to save new name.
Restore stations
Stations which have been deleted from the station list can be restored.
Green button: Starts Restore stations.
Delete station
Change stations
Restore stations
3sat
KIKA
ZDF
ZDFinfokanal

ZDFdokukanal 
ZDFinfokanal

Eurosport

NONAME

RTL
Phoenix
BRalpha
NDR FS HH
ed button: Starts Delete station.
R
56mark several stations if needed,
OK to execute the delete.
Move station / Change order
➠N
ot possible for MHEG-5 stations.
➠ S tations can only be resorted within their signal source
block.
Yellow button: Starts Move station.
56mark several stations if needed,
OK to end marking.
56Selection insert position from which the marked
stations are to be inserted,
OK to execute the move.
- 26
OK
P+
P–
Page ↑↓
Restore
Cancel restore
OK
Das Erste
Das Vierte
RTL Television
9Live
WDR Köln
VOX
ProSieben
Super RTL
n-tv
DSF
RTL2
KABEL1






END
INFO
5634Select station,
OKstation is restored.
The restored station is sorted in according to its signal
source at the end of the respective signal block.
Managing stations
Put together / change favourites lists
Add station to favourites list
Each favourites list can contain up to 99 stations. You can put together
the favourites lists to suit your requirements (e.g. topic lists). Other persons
using this TV set can create their own favourites lists.
The favourites lists also have the advantage that the stations of different
signal sources can be stored in the order you wish.
➠C
hange favourites can also be called via the favourites
list (page 19).
Call TV menu.
34Select Settings,
6go to the menu line below.
34Select Stations,
6go to the menu line below.
34Mark Select/change favourites,
OKcalls list of all stations and last active favourites list.
Select/change favourites
All stations
1
2
3
4
5
6
7
8
9
10
11
12
Das Erste
ZDF
WDR Köln
Bayrisches FS
hr-fernsehen
Phoenix
BR-alpha
3sat
EinsExtra
EinsFestival
SAT.1
RTL












1
2
3
4
5
6
7
8
9
10
11
12
Das Erste
ZDF
WDR Köln
Bayrisches FS
hr-fernsehen
Phoenix
BR-alpha
3sat
EinsExtra
EinsFestival
SAT.1
RTL












Page ↑↓
-
9
Select station
Clear favourite list
Next favourite list
Change sorting
56M
ark station or select station with the numeric
buttons (for alphabetical station sorting enter the
initial letter) which is to be transferred as a favourite
to the favourites list.
OK transfers the station to the favourites list.
The new station is inserted at the end of the favourites
list. Proceed in the same manner with additional
stations.
Delete station from favourites list
56Mark station to be deleted.
OK Removes the marked station from the favourites list.
or:
Red button: Starts Clear favourite list.
END
0
P+
P–
P+/P– Scroll in the pages of the station list if necessary.
➠ F avourites list (right column) must be selected.
If not, change the list with 4.
Stations of Favourite list1
OK
➠A
ll stations (left column) must be selected. If not, change the list with 3.
OK confirms clear favourites list.
INFO
Green button: Select the next favourites list.
Rename favourites list
Move / change order of stations in the favourites list
➠ F avourites list (right column) must be selected.
If not, change the list with 4.
➠ F avourites list (right column) must be selected. If not, change the list with 4.
56Mark station to be moved.
Blue button: Starts Rename favourites list.
Yellow button: Starts Move station.
Numeric buttons: Enter new name (same procedure as
for rename station, see page 26).
OK to save new name.
56Select insertion position at which the marked
station is to be inserted.
T he insertion position can also be selected with
the numeric buttons.
OK to execute the move.
27 -
Picture in Picture
Picture in Picture (PIP)
Swap contents of PIP and main picture
The concurrent display of two different images is referred to as Picture
in Picture.
➠ T he frame is green,
if not, press the green button.
➠ The coloured buttons do not work as described below for TV sets with
MHEG-5 software, but they operate as described on page 33 (Digital
Teletext).
➠ A concurrent representation of two HDTV signals is not possible.
➠ A concurrent representation of two coded stations is not possible.
➠ Picture change and station selection is restricted during recording.
Yellow button: Swaps contents of TV picture and PIP picture.
Select the PIP picture
➠ T he frame is green,
if not, press the green button.
Select the station as usual.
Your TV set distinguishes between two PIP displays:
Split screen In this case the screen is divided in the middle and the additonal PIP image is shown on the right side of the screen.
Both images are compressed horizontally and each gets
half of the screen.
Small PIP In this case a small PIP image is inserted in the TV picture.
The PIP operation distinguishes between two functionalities:
Standard PIP Stations freely selectable and changeable for PIP and TV
picture (coloured buttons have PIP-specific meaning, see
below).
iPIP The TV picture is moved to the PIP picture when you press
the PIP button. The station of the TV picture is now freely
selectable. When you press the PIP button again, the PIP picture returns to the TV picture and the PIP window closes.
2 ZDF
17.00 - 18.30 Flora & Fauna
Select the station for the main picture
➠ T he frame is white,
if not, press the green button.
Select the station as usual.
Start and end Picture in Picture mode
Show/hide PIP.
In the Standard PIP function a green frame indicates that the
station selection acts on the PIP picture. A white frame means
that the operation refers to the main picture. If the frame is
blue, the station scan is active in the PIP picture. If the iPIP
function is activated, this is indicated by an orange frame.
➠ For TV sets with MHEG-5 Software, you switch from
the green bar/frame to the white by using the PIP key.
The next time you press the PIP key, PIP is switched off.
Standard PIP operation:
PIP as freeze picture
➠ T he frame is green,
if not, press the green button.
Red button: Freeze picture in PIP on / off.
- 28
1 ARD
17.30 - 20.00 Toskana
Scan station in the PIP
➠ T he frame is green,
if not, press the green button.
Blue button: Start Scan stations.
The frame turns blue,
the stations now change automatically.
Blue button: Stop Scan stations.
The frame is green again.

Picture in Picture
Configure Picture in Picture (PIP) mode
Change position of the PIP small picture
➠ Other than the status line, which may possibly be
displayed, no other display is shown on the screen:
In the PIP menu you can set the PIP type (Split Screen or Small PIP), the
PIP function (Standard PIP or iPIP) and the position of the small picture.
Start PIP menu
➠ P IP mode started,
if not, press PIP button.
➠ T he frame is green,
if not, press the green button.
Call PIP menu.
5634Move the PIP into a corner of the screen.
The position of the small picture can also be selected
under Position in the PIP menu.
TV menu
Settings
PIP
Type
Split screen
Switch to iPIP / Standard PIP function
INFO
...
END
➠ PIP menu open.
Functions
Switch to Small PIP / Split screen
➠ PIP menu open.
TV menu
Settings
PIP
Functions
iPIP
INFO
END
Standard PIP
34Select Functions,
6go to the menu line below.
TV menu
Settings
PIP
Type
Small PIP
INFO
Split screen
34Select Type,
6go to the menu line below.
34Select Small PIP or Split screen.
34Select iPIP or Standard PIP.
In iPIP the frame around the PIP picture is orange.
END
iPIP operation:
When the iPIP function is set, the currently displayed
picture becomes the PIP picture on pressing the PIP
button. You can select other stations for the TV picture
and still keep an eye on the PIP picture. You can temporarily “ban” commercials or programme sections to the
PIP picture in this way.
The PIP picture becomes the TV picture again (PIP off).
29 -
Electronic Programme Guide
Electronic Programme Guide – EPG
Adjusting the programme list
➠ T he selection is at the top of the specifications,
if not, press the blue button.
EPG stands for Electronic Programme Guide and provides you with
on-screen programme details. With the system, as with a printed programme guide, you can learn about the current programme. In addition
programmes can be sorted according to certain topics, memorised, and
also recordings can be programmed.
65Select Date, Time, Stations or Topics.
34Select defaults within the respective line.
EPG (Electronic Programme Guide)
Starting and ending EPG
Date
Time
Stations
Topics
Switch EPG on / off.
➠A
wizard will guide you through the necessary presettings
the first time you start the EPG. If you have analogue
reception, you enter the data capture for analogue
stations after that (see page 31).
➠ For TV sets with MHEG-5 software, EPG is only possible
for DVB-T stations.
EPG (Electronic Programme Guide)
Date
Time
Stations
Topics
TEXT
P+
P–
Detail
Page ↑↓
OK
0
-
9
View
Select time
Charmed - Zauberhafte Hexen 
Change to programme list
Mon 31.07./16:05
Mon 31.07.
now
until 17:00
17:00
18:00
19:00
all
all
arte
15:57-16:59 Charmed - Zauberhafte Hexen OK
Das Erste
16:00-16:10 Tagesschau
ZDF
16:00-16:10 heute - in Europa
WDR Köln
16:00-16:15 WDR aktuell
Bayerisches... 16:00-16:05 Rundschau
hr-fernsehen 16:00-16:30 Schlemmerreise Spanien
MDR FERNS... 16:00-16:15 Hier ab vier
NDR FS HH
16:00-16:30 Tipps und Trends - Der Verbraucher...
SWR Fernse... 16:00-16:05 Baden-Württemberg aktuell
Charmed - Zauberhafte Hexen 
2 ZDF
2 ZDF
Record
Select date, ... , topics
END
MENU
The display of the programme guide is divided into two
branches. The programme list (bottom) is influenced by
certain specifications (top).
Blue button: Switches between the upper default lines
Date, ..., Topics and the lower programme list.
Switching and memorizing with the programme list
➠ In the programme list first all currently running
programmes are listed.
➠Y
ou are in the lower programme list,
if not, press the blue button.
65Select station.
OK View / Memorise.
- 30
View The programme is in progress. The TV set switches to the
marked programme.
Memorise The programme has not started yet and is memorised. A 
appears in front of the programme. The TV set switches over
automatically to the beginning of the programme or, if set
in the EPG menu (page 31) on from standby mode.
Mon 31.07./16.05
Mon 31.07.
Tue 01.08. Wed 02.08. Thu 03.08. Fri
now
all
all
arte
15:57-16:59 Charmed - Zauberhafte Hexen
Das Erste
16:00-16:10 Tagesschau
ZDF
16:00-16:10 heute - in Europa
WDR Köln
16:00-16:15 WDR aktuell
Bayerisches... 16:00-16:05 Rundschau
hr-fernsehen 16:00-16:30 Schlemmerreise Spanien
MDR FERNS... 16:00-16:15 Hier ab vier
NDR FS HH
16:00-16:30 Tipps und Trends - Der Verbraucher...
SWR Fernse... 16:00-16:05 Baden-Württemberg aktuell
END
MENU
Example If you are searching for the next news, select today’s date,
17:00 for example for the time, all for station and News
for topics. Then you get a list of all news programmes
from 17.00 h onwards in the programme list below it.
The type of list of programmes in the programme list
depends on the setting of the sorting in the EPG menu
(page 31).
Time entry If the line Time is selected, then you can enter the time
after which the programmes will be displayed, via the
numeric buttons of the remote control. The broadcasts
are sorted according to the order of the station list within
the selected time window.
Stations If a favourites list has been selected, only the programmes
of stations from the favourites list are displayed in the
programme list. A single station can be selected with
“...”. The Select single station window is opened. After
selection, only programmes of the selected single station
are displayed.
Hint Before pressing the blue button to leave the upper selection lines, select one of the preceding lines. If you then
switch back to the programme list, you can change this
menu line with 34, without having to leave the programme list. If you have marked Time, then you can enter
the time, after which the programmes will be displayed,
with the numeric buttons of the remote control.
Paging through the programme list
P+/P– Page backwards / forwards.
In the entries for Date and Time, you will see changes in
time as well as in date when paging. Scrolling in the
programme list is also possible when the selection is at
the top of the specifications.
Electronic Programme Guide
Calling additional information about the programmes
➠ Brief information about many programmes is displayed
below the programme list of the broadcasts.
You can call detailed information with the TEXT button if
this function is offered by the TEXT icon in the lower left.
Programming a recording for a recorder
➠ T he selection is in the lower programme list,
if not, press the blue button.
65Mark the desired programme.
Red button: Starts recording wizard.
Change or confirm timer data if necessary (see page 54,
"The direct way to record").
Then a red dot will be displayed in front of this programme
as an identification.
Red button: Deletes the already programmed recording
of the red marked programme from the timer.
If the timer data have been transferred to an external
recorder, then the timer must also be deleted there.
Configuring EPG
Start the EPG menu
➠ E PG mode is started,
if not, press the EPG button.
Call the EPG menu.
Select provider
EPG menu
Station selection
INFO
OK
Data capture
Switch on TV when marked
END
Station In the station selection you can determine for which
selection station in the programme guide information is to be displayed. Only stations with  are shown in the EPG.
With the coloured buttons you can select or remove
stations or only select the stations from the favourites
lists.
Because of the large number of receivable DVB-S stations
you should restrict the station selection. This reduces the
data entry time and increases the clarity in the EPG.
Marking the stations according to reception ranges:
 Analogue stations via antenna/cable, for which the current provider supplies data.
 Digital terrestrial stations DVB-T.
 Digital cable stations DVB-C.
 Digital satellite stations DVB-S.
Data capture on (for DVB + analogue): data capture for DVB and analogue stations
on (only for DVB): data capture only for DVB stations.
off: no data capture.
After changes in the EPG menu or after switching off at
the mains switch the EPG data must be collected first.
To do this, switch on the set and select the station from
the analogue stations which you want defined as a provider and let the TV set run for about 1 hour with the
selected station. Or:
Switch the TV set into standby mode. The display on the
TV set glows orange after 2 minutes and the EPG data
entry begins.
The data capture normally takes place at night between
2 and 5 o’clock if the TV set is in the standby mode.
Sorting
Settings in the EPG menu:
Select provider (only for analogue stations), Station selection, Data capture, Switch on TV when marked, Sorting.
Explanations of setting possibilities in the EPG menu:
Select In analogue TV reception there may be different providprovider ers who transmit the EPG data for certain station packages.
You can have the list of providers created automatically
with the yellow button in the provider selection. You can
select the desired provider at the end of the provider
search. You can create the list of providers manually with
the blue button.
Switch on TV When yes is set, the switched off TV switches on autowhen marked matically from the standby mode at the beginning of a
set program. A screen message appears when switching
on. If this is not confirmed within 5 minutes with the
OK button, the TV switches back off automatically for
safety reasons.
Sorting The programmes can be sorted either according to their
start times (chronologically) or according to stations (corresponding to station list).
31 -
Teletext
Teletext
Additional page selection possibilities
Your TV set supports the two operating systems TOP Text and FLOF.
Up to 2,000 pages are stored so that you have quick access.
1st possibility:
Call overview page 100.
Starting and ending Teletext
2nd possibility:
Directly enter the page number.
Switch Teletext on / off.
100
100
ARDtext
Do
07. 09. 06
14 : 14 : 42
100
ARD Text
Politik: Die neuen Gesetzesentwürfe
Wird auch der Nahverkehr teurer? . .
Australien: Keine Zugeständnisse . .
Tote bei Zugunglück in Schweden .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
204
213
204
13:00
14:00
312
ARD-Mittagsmagazin . . . . . . . . . . . . . . . . .
Tagesschau
–
+
110/112
170
200/600
300/400
Inhalt
07. 09. 06
14 : 14 : 42
ARD Text
65Mark desired page number.
Kultur. . . . . . . . . .
500
Gesellschaft . . . . .
530
Lotto/Toto. . . . . . .
666
Wirtschaft. . . . . . .
700
tagesschau
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
120
121
122
532
Tennis: Auftaktmatch wurde abgebrochen . . . . . . .
Formel 1: Neues Reglement für Motoren. . . . . . . . .
Fussball: Heimsieg für den Meister . . . . . . . . . . . .
204
213
204
13:00
14:00
312
ARD-Mittagsmagazin . . . . . . . . . . . . . . . . .
Tagesschau
100 100
ARDtext
Do 07. 09. 06
14 : 14 : 42
Tagesschau . . . .
110/112
Kultur. . . . . . . . . .
500
Wetter. . . . . . . . . .
170
Gesellschaft . . . . .
530
Sport. . . . . . . . . . . 200/600
Lotto/Toto. . . . . . .
666
TV Guide . . . . . . . 300/400
Wirtschaft. . . . . . .
700
Inhalt
tagesschau
–
+
ARD Text
OK
Politik:Page
Die selection
neuen Gesetzesentwürfe
Wird auch der Nahverkehr teurer? . .
Australien: Keine Zugeständnisse . .
Tote bei Zugunglück in Schweden .
OK Call the page.
Page selection with the coloured buttons
Back to the previously viewed page.
On to next page.
To next topic.
To next range of topics.
.View
. . .
. . . .
. . . .
. . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
120
121
122
532
Tennis: Auftaktmatch wurde abgebrochen . . . . . . .
204
213
204
13:00
312
Formel 1: Neues Reglement für Motoren. . . . . . . . .
4th possibility:
Fussball: Heimsieg für den Meister . . . . . . . . . . . .
ARD-Mittagsmagazin . . . . . . . . . . . . . . . . .
➠ T he 14:00
page Tagesschau
consists of several sub-pages (indicated by
Tagesschau . . . .
Kultur. . . . . . . . . .
500
the selection
option 110/112
on 170
the last
line).
Wetter. . . . . . . . . .
Gesellschaft . . . . .
530
Sport. . . . . . . . . . .
TV Guide . . . . . . .
–
The coloured bars (for TOP) or the coloured text (for FLOF)
in the second to last line indicate which coloured buttons
you can use to page through topic areas and topics.
+
200/600
300/400
Inhalt
Lotto/Toto. . . . . . .
666
Wirtschaft. . . . . . .
700
tagesschau
1 2 3 4 5
34Page through sub-pages.
Call TOP table
Teletext page displays
0 AV:
Stop self changing pages.
➠ The table
can only
be called
with
the
100 100
ARDtext
Do for
07. stations
09. 06
14 : 14
: 42TOP
operating system.
9:
Enlarge page (press several times).
OK Call TOP table.
ARD Text
PIP button: Show / hide TV picture.
100 100
ARDtext
Do 07.09.06
14:14:42
ARD Text
Politik: Die neuen Gesetzesentwürfe. . . . . . . . . .
Wird auch der Nahverkehr teurer?. . . . . . . . . . . .
Australien: Keine Zugeständnisse . . . . . . . . . . .
Tote bei Zugunglück in Schweden . . . . . . . . . . .
120
121
122
532
Tennis: Auftaktmatch wurde abgebrochen . . . 204
Formel 1: Neues Reglement für Motoren. . . . . . . 213
Fussball: Heimsieg für den Meister . . . . . . . . . . . 204
13:00 ARD-Mittagsmagazin . . . . . . . . . . . . . . . . 312
14:00 Tagesschau
Tagesschau . . . 110/112
Wetter. . . . . . . . . . . 170
Sport. . . . . . . . . 200/600
TV Guide. . . . . . 300/400
Inhalt
–
+
Page selection
- 32
Do
Politik: Die neuen Gesetzesentwürfe
Wird auch der Nahverkehr teurer? . .
Australien: Keine Zugeständnisse . .
Tote bei Zugunglück in Schweden .
Page selection
Red button:
Green button:
Yellow button:
Blue button:
ARDtext
➠ The page includes 3-digit page numbers.
120
121
122
532
Tennis: Auftaktmatch wurde abgebrochen . . . . . . .
Formel 1: Neues Reglement für Motoren. . . . . . . . .
Fussball: Heimsieg für den Meister . . . . . . . . . . . .
Tagesschau . . . .
Wetter. . . . . . . . . .
Sport. . . . . . . . . . .
TV Guide . . . . . . .
100
3rd possibility:
Kultur . . . . . . . . . . 500
Gesellschaft . . . . . 530
Lotto/Toto. . . . . . . 666
Wirtschaft. . . . . . . 700
tagesschau
Politik: Die neuen Gesetzesentwürfe
Wird auch der Nahverkehr teurer? . .
Australien: Keine Zugeständnisse . .
Tote
bei Zugunglück in Schweden .
TOP
table
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
120
121
122
532
ARD
Text Auftaktmatch wurde
Wetter
Tennis:
abgebrochen . . . . . . . 204
tagesschau
Formel 1: Neues ReglementVorhersage
für Motoren. . . . . . . . . 213
Fussball: Heimsieg für
OK
den Staedte
Meister . . . . . . . . . . . . 204
Wetter
Sport
1
Ballungsr.
13:00 ARD-Mittagsmagazin . . . . . . . . . . . . . . . . . 312
Fußball
Reise
14:00 Tagesschau
TV Guide
Tagesschau
. . . .
110/112
Kultur. . . . . . . . . .
500
ARD
heute
Wetter.
. . . . . . . . .
170
Gesellschaft . . . . .
530
ARD
morgen
Sport. . . . . . . . . . . 200/600
Lotto/Toto. . . . . . .
666
Kultur
TV Guide . . . . . . . 300/400
Wirtschaft. . . . . . .
700
weitere ... +
Inhalt
tagesschau
–
OK
View
Seitenauswahl
65Mark topic area,
34select topic column,
65select topic,
OK call the page.
Teletext
Programming timer recordings via Teletext
➠ T eletext is started,
if not, press the TEXT button.
Explanations of the Teletext menu functions:
Recording
wizard
Call the programme pages of the current station.
Settings
Green button: Go to the appropriate page.
Change the appropriate recording data in the following
menu Timer data if necessary (see also page 54, "The
direct way to record").
OK Confirm.
Sub-title Input of the teletext subtitle pages for every station if this
pages deviates from the factory setting (page 150).
Personal Define up to six teletext pages which can be opened later
text pages from a list in the menu Teletext functions → Personal text
pages (in TV mode press green button, see page 22).
Character set
Teletext menu
In the Teletext menu you can, among other things, activate news, reveal
pages and configure the teletext with the Settings menu function.
Starting the Teletext menu
Do
07. 09. 06
14 : 14 : 42
➠ Only for TV sets with MHEG-5 software.
➠ At the moment only available in United Kingdom and Ireland.
➠ Digital teletext is not available when DVB subtitles are being displayed.
ARD Text
Politik: Die neuen Gesetzesentwürfe
Wird auch der Nahverkehr teurer? . .
Australien: Keine Zugeständnisse . .
Tote bei Zugunglück in Schweden .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
120
121
122
532
Tennis: Auftaktmatch wurde abgebrochen . . . . . . .
Formel 1: Neues Reglement für Motoren. . . . . . . . .
Fussball: Heimsieg für den Meister . . . . . . . . . . . .
204
213
204
13:00
14:00
312
ARD-Mittagsmagazin . . . . . . . . . . . . . . . . .
Tagesschau
Tagesschau . . . .
Wetter. . . . . . . . . .
Sport. menu
. . .. . . . . . .
Teletext
TV Guide . . . . . . .
OK
Newsflash
–
+
Improved graphic representation of the Teletext.
(Not offered by all stations.)
In the UK or Ireland, the teletext for DVB-T stations is transmitted as per
the MHEG-5 standard. It contains text, graphics, functions and links.
Call the Teletext menu.
ARDtext
HiText
Teletext character set can be switched to other languages
(Russian, Greek, Polish and Turkish).
Digital teletext (MHEG-5)
➠ T eletext is started,
if not, press the TEXT button.
100
Other Teletext menu functions:
Preview Input of the first teletext programme preview page if this
pages deviates from the factory setting (page 301).
65Select the desired programme,
OK to programme the recording.
100
A wizard for recording via teletext helps to programme
an external recorder or the integrated Digital Recorder,
see also the left column.
110/112
Kultur. . . . . . . . . .
500
170
Gesellschaft . . . . .
530
INFO
200/600
Lotto/Toto. . . . . . .
666
300/400
Wirtschaft. . . . . . .
700
Reveal
Recording wizard
Settings
Inhalt
tagesschau
END
Seitenauswahl
Explanations of the Teletext menu functions:
Newsflash The current page is hidden when you activate Newsflash.
A symbol at the top left indicates that the function is active. If the contents of the message are updated and it is
a small newsflash, this is displayed in the TV picture. If it
is a full screen page, the symbol is displayed in blue and
the page can be called with the OK button.
Reveal Shows concealed information, e.g. for quiz questions or
VPS times in the programme preview pages.
The operation of these menus depends on the particular
provider. Normally after a station is changed, the provider
broadcasting the digital teletext makes an introductory
offer for this service on the screen via menu selection.
Follow these notes.
If no message appears telling you how to switch to digital
teletext after switching to another station, press the TEXT
key. If a selection for DVB subtitles is available, this item
must be hidden before.
Depending on the provider’s respective offer, you can use
the 5634buttons and the OK button, the coloured
buttons, the END/TEXT button and sometimes even the
numeric buttons.
If you want to close the digital teletext, just select a different station using the P+/P– buttons or follow the menu
prompts on the screen.
33 -
Radio
Radio mode
Switching the screen on/off
Red button: Switch off the screen.
You can only receive radio stations via DVB.
If you do not have DVB radio reception then you can play audio from an
external device via the TV set using the audio/AV inputs.
➠ For TV sets with MHEG-5 software, the buttons may be configured
differently by the provider.
Switch on the screen with the remote control:
Red button, OK button or RADIO button.
Radio mode on
Switch on the screen on the TV set:
Press R on the TV set operating ring.
The LED display on the set changes from green to orange.
RADIO button on the remote control.
Or: R on the operating ring on the TV set.
Radio
15:07
digital
1 DLF
15:05 - 16:00
Stereo
Corso
2
Informationen und Musik
Volume
OK
INFO
Call radio menu
30
Station list
Detail off
Radio menu
In the Radio menu, you can set the sound, search for and store radio
stations (automatically or manually), change stations and set switch
off/alarm functions.
The settings are made as described in TV mode.
Screen off/on
Previous station
TV
MENU
You see and information window about the currently set
station.
➠R
adio mode switched on,
if not, press the RADIO button.
Call the Radio menu.
Radio menu
Sound
Sound mode
Minimise Radio dialogue to an info line / maximise.
Radio
digital
1 DLF
INFO
...
Stations
END
Timer functions
15:07
Stereo 2
INFO
Switch off radio mode
TV button on the remote control.
Station switching
P+/P– or the numeric buttons of the remote control.
Or: R on the operating ring on the TV set.
Or:
+ / – on the TV set operating ring.
Or:
OKCall station list / favourites.
➠ T he selection of the stations / favourites is the same
as the procedure in TV mode (see pages 18 and 19).
Setting the volume
V+/V– Volume louder / quieter.
Other sound settings are the same as for the volume setting
in TV mode (see page 20).
Setting the sound mode
Call Sound mode.
Other settings as for TV mode (see page 20).
- 34
EPG – Electronic Programme Guide (radio)
For the DVB radio stations you can also use an electronic programme
guide, if the station that is currently active supplies data.
Starting and ending EPG
➠R
adio mode switched on,
if not, press the RADIO button.
Switch EPG on / off.
➠ T he EPG functions in radio mode are the same as in
TV mode. Read from page 30 onwards for further
information.
DVB
Conditional Access module (CA module)
In order to receive coded digital stations, a Conditional Access module
(CA module) and a Smart Card must be inserted in the CI slot of your TV
set (see page 5 and 6).
The CA module and the Smart Card are not part of the TV set's scope
of delivery. They are usually available from your dealer. Loewe does not provide any guarantee for the functioning of the CA module.
Inserting the Smart Card into the CA module
Push the Smart Card into the CA module as far as it goes so that the side
with the gold coloured contact chip is facing the side of the CA module
marked with the provider's logo. Note the direction of the arrow printed
on the Smart Card.
Searching for encrypted stations
➠ T he search wizard must only be started if the setting
option no has been selected during first installation in
the search for encrypted stations or no CA-module was
inserted.
Call TV menu.
34Select Settings,
6go to the menu line below.
34Select Stations,
6go to the menu line below.
34Select Search wizard,
6go to the menu line below.
34Select Change search settings,
OKwizard guides you through the search settings.
See page 24 for a description of the search settings.
Calling CA module information
➠ This menu is only available for digital stations.
Call TV menu.
Inserting the CA module in the CI slot
➠ Switch off the TV set's mains switch.
Ejector
button
Remove the cover from the rear of the set.
Cover
34Select Settings,
6go to the menu line below.
34Select Miscellaneous,
6go to the menu line below.
34
Select CA module: xxx
(xxx corresponds to the CA module provider),
OKcall information.
The content of this menu depends on the provider of the
CA module.
Removing the CA module
➠ Switch off the TV set's mains switch.
Remove the cover from the rear of the set.
Carefully insert the CA module in CI slot 1 or CI slot 2
with the contact side forward.
If you are standing in front of the TV set (display) then
the logo on the CA module must be pointing to the rear.
Do not use force. Make sure the module is not twisted
in the process. If the CA module is correctly installed, the
ejector button protrudes a little further.
Replace the cover.
Press in the ejector button on the appropriate module
drawer, the module is released.
Remove the module from the set.
Replace the cover.
35 -
DVB
Software update
TV base software and DVB software
Your TV set provides the option to update the TV basic and DVB software. The current software versions can be installed on your set with a
USB stick.
Contact your dealer for a software update by USB stick.
The software can also be updated by different DVB reception paths (DVBT, DVB-C, DVB-S).
However, the prerequisite for this is that the software is provided by the
appropriate DVB reception path.
This may differ depending on the TV set and the DVB program provided.
Ask your local dealer for information whether a software update via DVB
reception path is possible.
Automatic information by new software version
In the Change update settings menu (see right column) you can determine
via which DVB reception path (if possible) you want to receive updates.
Your TV set determines automatically overnight whether a new software
version is available via the selected DVB reception path. The TV set must
be left in the standby mode for this (do not switch off with the mains
switch).
If a new software version is available, the TV set informs you of this in an
on-screen message the next time it is switched on (see page 37 – Loading
new software).
Manual search for new software
If it is not displayed automatically that a new software is available when
you switch on the set, you can also search for one manually. The search
depends on the selected update source(s).
Call TV menu.
34Select Settings,
6go to the menu line below.
34Select Miscellaneous,
6go to the menu line below.
34Select Software update.
OK Open the software update wizard.
The current update settings are displayed in the info
text.
Software update wizard
The software update can be made via a USB stick or DVB antenna. If you do
not make any changes, your TV makes it with the following settings:
Update source
USB and satellite: ASTRA1 19,2°E (DVB-S)
(ASTRA1 19,2°E)
Frequency
12603 MHz
Symbol rate
22000
Band
horiz/high
TV menu
Settings
Miscellaneous
Software update
Start update
END
OK
Change update settings
If you want to change the update settings:
34Select Change update settings,
OK the wizard polls the update settings.
➠ The selection options depend on the antenna cables
connected at the initial installation (see page 12).
USB only
New software is searched for via USB.
USB and DVB-T
New software is searched for first via USB then via DVB-T
(digital terrestrial transmission).
USB and DVB-C
New software is searched for first via USB then via DVB-C
(digital cable transmission).
USB and satellite
New software is searched for first via USB then via DVB-S
(digital satellite transmission). The name of the currently
selected satellite is displayed.
Setting parameters of the different DVB update sources:
Channel Select the channel on which the new software is provided.
Frequency Enter the frequency of the station to be transmitted
directly.
Bandwidth Is preset automatically depending on the selected channel.
Symbol rate Enter the symbol rate of the station to be transmitted
directly.
QAM Set the suitable type of modulation.
modulation
Band Set the transmission range for satellite reception.
- 36
continued on the next page
Ž
DVB
If you have adapted the update settings:
OKproceed.
A bar informs you about the progress of the charging
process. Do not switch your set off during this time! 34Select Start update,
OKstart update procedure.
This process can take up to 20 minutes depending on the
selected update source. You will be informed at the end.
Software update wizard
Current TV base software:
Current DVB software:
At the end of charging:
Switch the TV set off and back on with the mains switch.
This is unnecessary when loading the software with the
Load new software after switch´off to standby update
option.
V4.3.0
V4.3.0
You can now search for new software. Please select the software type and
start the search with the OK button.
If a new software has not been updated by a DVB station,
you will be reminded of this several times when switching
on the set.
Software update
Software type
TV base software
DVB software
OK
OK
END
Proceed
Select software type:
TV base software or DVB software,
OKstart search.
➠ If a new TV software and a new DVB software are
available in the automatic search for new software via
DVB stations (see page 36), you can choose which
software is to be updated.
If a new software version is available after the search, the
following screen message appears.
Loading new software
Software update wizard
A new software is available.
TV base software:
current V4.3.0
new V4.4.0
Please specify whether and, if so, when you want to load the new software.
Software update
Update options
Load new software now
Load new software after switch off to standby
Keep current software
OK Proceed
OK
END
Select update option:
Load new software now
Load new software after switch off to standby
(update after switching off)
Keep current software (no update desired).
OKProceed or exit wizard.
OKStart Software update.
37 -
Other settings
Parental lock
Timer functions
You can select and set various security options to prevent unauthorised
use of the TV set and to protect your children from unsuitable programmes.
This menu offers you convenient alarm services. Programmed alarms are
also active when the TV set has been switched off to standby.
If the TV set switches on from the standby mode by alarm, a screen
message appears. If this is not confirmed within 5 minutes with the OK
button, the TV switches back off automatically for safety reasons.
The TV set can also be switched off automatically at certain times. A screen
warning appears one minute before automatic switch off. The automatic
switch off can be interrupted by pressing any button.
Defining the access code (PIN)
Call TV menu.
34Select Settings,
6go to the menu line below.
34Select Parental lock,
6go to the menu line below.
Define a four digit access code (PIN) the first time
you open it. The numbers appear in plain text. Note
the access code (PIN) well.
Call Timer functions
Call TV menu.
34Select Settings,
6go to the menu line below.
34Select Timer functions,
6go to the menu line below.
OK Confirm the access code (PIN).
The Parental lock menu is opened.
The four-digit access code (PIN) must be entered when
the parental lock is opened in future. It appears encrypted
(****) when entering for security reasons.
Code number
The code number cancels all entered PINs. It can be used for example if
you have forgotten your PIN. You will find a note about the code number
on page 69. Remove this from the manual and keep it in a safe place.
Explanations of setting possibilities in the Parental lock menu:
Lock
immediately
The TV set is locked immediately on exiting the menu.
Programmes of any kind can then only be watched after
entering the PIN.
The lock remains active until switching off in the menu.
Lock daily
The TV set is locked daily at the fixed time. Programmes
of any kind can then only be watched after entering
the PIN.
Age-related
lock
Some DVB stations also broadcast an age classification. If
the age set here is below the broadcast age limit, the programme can only be watched after entering the PIN.
Change
access code
You can change your PIN at any time. Enter the new PIN
in place of the old one.
Delete You can delete your entered PIN at any time.
access code
- 38
34Select the desired setting.
Explanations of setting possibilities in the Timer functions menu:
Switch off
today only
The set switches to the standby mode automatically at
the specified time.
If a time is specified which has already passed on the same
day, the set switches off at this time the next day.
Switch off
daily
The set regularly switches to the standby mode automatically every day at the specified time.
One-time
reminder
The set alerts you once today at the specified time.
If a time was specified which has already passed on the
same day, the alarm is saved for the next day.
Wake up
Mon-Fri
The set regularly alerts you from Monday to Friday at
the set time.
Wake up Sat
The set alerts you regularly every Saturday at the specified time.
Wake up
Sun
The set alerts you regularly every Sunday at the specified time.
Wake up
with
Specify whether the TV set switches on in the event of an
alarm from the standby mode in TV or radio mode with
the respectively last active station.
Wake up
signal
volume
Set the desired volume of the alarm tone. The alarm
tone is emitted as a continuous tone as a guide during
the setting.
Other settings
On-screen displays
Time and date
You can select different settings in this menu which affect the on-screen
displays.
If you receive a station with teletext after switching on the TV, the time
and date are recorded automatically. The date may have to be entered
manually for some stations.
Enter the time and date manually if you receive station without teletext.
Call On-screen displays
Call TV menu.
34Select Settings,
6go to the menu line below.
34Select Miscellaneous,
6go to the menu line below.
34Select On-screen displays,
6go to the menu line below.
34Select the desired setting.
Explanations of setting possibilities in the On-screen displays menu:
On-screen Here you set the duration of the display, e.g. for the voldisplay time ume or the station display when changing stations.
The duration can be set between 2 and 9 seconds.
On-screen You can select between an upper and a lower display posidisplay position tion so that other displays (subtitles) are not concealed.
Volume Here you set whether or not the change in the volume
should also be displayed visually on the screen.
Automatic Select yes here if you want to be able to see the addiInfo tional help permanently in the upper part of the screen
while navigating the menu. Also see page 15 for further
information.
Call time and date
Call TV menu.
34Select Settings,
6go to the menu line below.
34Select Miscellaneous,
6go to the menu line below.
34Select Time and date,
6go to the menu line below.
34Select the desired setting.
Explanations of setting possibilities in the Time and date menu:
Time Enter the time (00:00 to 23:59) with the numeric buttons
of the remote control.
Deviation from The current time at the Greenwich Meridian 0 is to be
Universal Time understood as world time. The time shift in relation to
this time must be given in hours (–11 to +13) (with the
buttons34or the numeric buttons on the remote control). Summer time is ignored.
Date Enter the date (day.month.year) with the numeric buttons
on the remote control.
Beginning of Enter the date on which the time is switched over to
daylight-saving summer time if it deviates from the automatically caltime culated date.
End of Enter the date on which the summer time ends if it devidaylight-saving ates from the automatically calculated date.
time
39 -
Operating additional equipment
Connection wizard
Select the equipment you want to connect or remove
equipment you no longer use in the AV equipment
selection.
The connection wizard serves to connect accessory equipment optimally
to the TV set, make changes to the wiring of the devices or remove momentarily logged in equipment. The exact process of the wizard depends
on the choice of equipment.
➠N
ew equipment should not be connected until it has been logged in
in the Connection wizard first.
➠ DVD player on AV1 and DVD recorder on AV2 are preset at the factory.
Call TV menu.
34Select Connections,
6go to the menu line below.
4Select New devices/modifications,
3
OK calls the wizard.
Connection wizard
Connect the satellite dishes or cable/terrestrial antennas of your AV
equipment (recorder, decoder, ...) to the TV set according to the enclosed
operating manual. The connection wizard assists you when you connect your
equipment to the TV set via the AV sockets AV1, AV2 and AVS or via the
SD/HD-COMPONENT IN or HDMI1/2(DVI)* socket.
56Select equipment/connection.
Yellow button: Connect/disconnect equipment.
A Camcorder / camera is connected to the TV set additionally in the following example.
AV equipment
selection
Connection wizard
Specify all new AV devices to be connected and all connection changes to the
existing devices here.
New devices/modifications
AV equipment selection
DVD
DVD player
DVD •
DVD recorder
VCR
Video recorder
SAT
Satellite receiver
STB
SetTopBox/dBox
Decoder
Decoder
Camera
Camcorder/camera
AV
Other device(s) to AV1/2/S
COMP.IN
Device to COMP.IN
HDMI/DVI Device to HDMI1/DVI
HDMI/DVI Device to HDMI2/DVI
OK
Proceed



END
Connect/disconnect
OK Proceed.
The connection diagram is displayed again. Connect the
equipment to the corresponding connections of the TV
set as shown in the connection diagram.
OK
END
Proceed
➠ T he connection wizard can be exited at any time with
the END button.
OK Proceed.
Connection wizard
Please connect your equipment as shown in the diagram.
The connection diagram shows the currently logged in
equipment.
Connection
diagram
Connection wizard
Now the TV set assumes that you have connected the following equipment:
AVS
➠ T he accessory equipment should be connected to the
TV set with the power off (disconnected from the
mains). See also the instructions in the operating
manual of the equipment to be connected.
DVD
DVD
AV1
AV2
COMP. IN
HDMI1
Camera
DVD
DVD
AVS
AV1
AV2
COMP. IN
HDMI1
HDMI2
HDMI2
OK
END
Proceed
OK Proceed.
OK
Proceed
OK Proceed.
- 40
END
continued on the next page
Ž
Operating additional equipment
Signal type
New devices/modifications
Signal type at socket AV1 (DVD)
Automatic CVBS/YC
CVBS
YC
OK Proceed
Digital Link
Plus
OK
END
56Select the signal types of the individual devices one
after another where necessary.
Normally you should leave the setting on Automatic
CVBS/YC (e.g. for DVD player/recorder) or Autom.VHS/SVHS (e.g. VCR), otherwise select the suitable
signal type.
OK Proceed.
Immediate
playback
New devices/modifications
Immediate playback
OK
no
OK Proceed
yes
END
34Select yes or no.
If playback is started on a device connected to AV1
or AV2, the TV switches immediately to the appropriate AV input when yes is set.
When playing devices with Digital Link Plus, the
appropriate AV input is always switched to regardless
of the setting.
OK Proceed.
Assign digital
audio input
New devices/modifications
Assign digital audio input
no
to AV1 (DVD)
to AV2 (DVD-REC)
to AVS (CAM)
to HDMI1/DVI
to HDMI2/DVI
to COMP. IN
to PC IN
OK Proceed
Connection wizard
Transfer of the station list to the Digital Link Plus recorder(s).
Transfer (per recorder):
OK
100%
Proceed
END
If you have registered a recorder into the connection
wizard, the Digital Link Plus transmission starts.
If a Digital Link Plus capable recorder is connected, the
station list of the analogue stations is transmitted to the
external recorder.
You can also call Digital Link Plus under TV menu → Connections → Digital Link Plus.
END: Exit connection wizard.
OK
END
56You have to feed the digital audio signal to the TV
set for the digital audio reproduction from an external device.
The digital audio input (AUDIO DIGITAL IN) of the TV
set must be assigned to the appropriate connection
of the external device.
If no is selected, the analogue sound is used.
OK Proceed.
41 -
Operating additional equipment
Devices to the connections AV1/AV2/AVS
Connecting a DVD player to the TV set
➠D
VD player is registered with the connection wizard.
Accessory equipment such as DVD players, video and DVD recorders
etc. can be connected to the TV set at the Euro-AV sockets AV1 and AV2
(see pages 5 and 6).
The AV input AVS (see pages 5 and 6) offers the possibility of connecting
a digital camera or a camcorder for example.
Switch off all equipment before connecting.
Connect the Euro-AV output of the DVD player to the
AV1 socket of the TV set.
Use a fully equipped Euro-AV cable (available from your
dealer) for this.
➠A
ll devices at the AV inputs must be registered in in the connection
wizard (see page 40 onwards).
The connection designations vary according to the logged in device. The
AV selection then contains, for example, DVD in place of AV1 or CAM in
place of AVS.
The Euro-AV sockets can process different signal types. Which signal type
your accessory device provides can be found in the operating manual of
the appropriate device.
TV set
Connection
example of a
DVD player
AV1
Owing to the large number of AV devices available on the market, we can
only mention a few examples for the connection of accessory equipment
to the AV sockets here.
The following description of the connected equipment to the connections AV1/2/S refers to the device types logged into the connection wizard
from page 40 onwards.
If the sound of a device connected to an AV socket is to be transmitted digitally, a cinch cable must be plugged between the coaxial digital
output of the accessory equipment and the AUDIO DIGITAL IN socket of
the TV set. In addition the digital audio input must be assigned to the
corresponding AV socket in the connection wizard (see page 41).
The assignment of the digital audio input may also take place outside
the connection wizard. With TV menu → Connections → Miscellaneous
→ Assign digital audio input, the digital audio input can be assigned to
the appropriate AV socket, see page 53.
DVD player
Playback from AV device
If the device supports Digital Link Plus on AV1/2 or if Immediate playback →
yes was selected in the connection wizard, the TV set switches automatically to the appropriate AV input after switching on the AV device
The AV input can also be called manually, however.
Call AV selection.
AV selection
COMP. IN
HDMI2/DVI
HDMI1/DVI
PC IN
AVS
DVD-REC
DVD
VIDEO
OK Switch to ...
OK
56Select DVD,
OK switch over.
Start playback on the connected device.
- 42
END
Operating additional equipment
Connecting a DVD recorder to the TV set
Connecting Camcorder/camera
➠ DVD
recorder is registered with the connection wizard.
➠C
amcorder/camera is registered with the connection
wizard.
Switch off all equipment before connecting.
Switch off all equipment before connecting.
Connect the Euro-AV output of the DVD recorder to the
AV2 socket of the TV set.
Use a fully equipped Euro-AV cable (available from your
dealer) for this.
Connect the AV output of the camcorder to the audio
input sockets L/R (white/red) and the S-VHS connection
of the AVS sockets of the TV set.
Use the AV cable enclosed with the camcorder for this.
Some camcorders only supply an FBAS signal instead of
an S-VHS signal at the AV output. In this case use the AVS
video input (yellow).
If you want to receive and record analogue stations with
the receiver (tuner) built into the recorder, the recorder
must be looped into the aerial cable. Connect the DVD
recorder as shown in the connection example below.
Connection
example of a
DVD recorder
TV set
Audio in
L/R (AVS)
Connection
example of a
camcorder
ANT2
AV2
S-VHS connection(AVS)
Camcorder
TV set
Playback from AV device
S-VIDEO OUT
DVD recorder
Call AV selection.
TV
R
➠ If you want to record DVB stations with an external
recorder, the internal receiver of the TV set must be
used (see “Timer recording with external devices” on
page 55).
Playback from AV device
OK
END
56Select CAM,
OK switch over.
Call AV selection.
AV selection
COMP. IN
HDMI2/DVI
HDMI1/DVI
PC IN
AVS
DVD-REC
DVD
VIDEO
OK Switch to ...
AV selection
COMP. IN
HDMI2/DVI
HDMI1/DVI
PC IN
CAM
DVD-REC
DVD
VIDEO
OK Switch to ...
Start playback on the connected device.
OK
END
56Select DVD-REC,
OK switch over.
Start playback on the connected device.
43 -
Operating additional equipment
Devices to the HDMI (DVI) connections
Playback from the device
The HDMI connections (High Definition Multimedia
Interface) allow the transmission of digital video and
audio signals from a player, e.g. DVD player, DVD recorder, Blu-ray player, game console or Set-Top-Box via
a single cable.
The digital video and audio data are transmitted without data compression digitally and therefore lose none of their quality.
Your TV set shows 24p films (see glossary on page 70) which are output
by a player connected via HDMI, e.g. Loewe BluTech Vision, automatically
in the original 24p format.
Film quality improvement (DMM) must be set to on (see page 21).
Digital video signals from a DVI player can be also be reproduced by the
HDMI connection using a DVI/HDMI adapter cable. The sound must be
piped in additionally.
HDMI and DVI both use the same copy protection method HDCP.
Connecting the device
➠ It is not necessary to register HDMI devices with the
connection wizard.
Switch off all equipment before connecting.
Connect the device with an HDMI cable (type A, 19-wire)
to the HDMI1/DVI or HDMI2/DVI socket of the TV set.
TV set
Connection
example of a
Blu-ray player
AV selection
COMP. IN
HDMI2/DVI
HDMI1/DVI
PC IN
AVS
DVD-REC
DVD
VIDEO
OK Switch to ...
OK
END
56Select HDMI1/DVI or HDMI2/DVI socket,
OK switch over.
Start playback on the connected HDMI device. The best
possible format for the picture is detected and set automatically.
Digital Link HD in CEC-capable devices
With Digital Link HD accessory equipment with CEC support (e.g. Loewe
BluTech Vision) is controlled by the TV set. A concealed installation of the
accessory equipment is also possible.
Operation of equipment with Digital Link HD
As long as a HDMI programme slot is selected, all remote control commands which can be processed by the device connected to the respective
socket are passed on to it. The device can therefore be installed concealed
and still be controlled.
➠V
olume setting, sound off/on, listen mode and selection of picture
format always act on the operation of the TV set.
HDMI2
Blu-ray player
If a DVI/HDMI adapter cable is used, the corresponding
sound can be piped through the AUDIO IN1 (analogue)
or AUDIO DIGITAL IN (digital) socket on the TV set (see
also page 53).
- 44
Call AV selection.
On/off button:
short: Switch off TV set to the standby mode.
long: Switch off TV set and connected Digital Link HDcapable equipment to the standby mode (system
standby).
TV button:
short: Switch back to the last viewed TV station.
long: Switch Digital Link HD on/off temporarily.
Remote TV switch on via Digital Link HD
In the TV menu under Connections → Miscellaneous → Remote TV switch
on via Digital Link HD, you can select whether the TV set is to switch on
automatically from standby mode when a disc is played or a screen menu
displayed on connected Digital Link HD-capable HDMI equipment.
Operating additional equipment
Devices to the PC IN connection
Playback from the device
You can connect a PC to the PC IN socket for example
and thus use the TV screen as a monitor.
➠W
hen connecting a PC or accessory equipment to the PC IN socket
of the TV set, set one of the following screen resolutions on the PC /
accessory equipment first.
800 x 600
60 Hz
1280 x 1024 60 Hz
720 x 576i
720 x 576p
1280 x 720p
(SVGA)
(SXGA)
(SDTV)
(SDTV)
(HDTV)
1024 x 768 60 Hz
1360 x 768 60 Hz
720 x 480i
720 x 480p
1920 x 1080i
(XGA)
(WXGA)
(SDTV)
(SDTV)
(HDTV)
Connecting the device
➠ T here is no need to register the device with the connection wizard.
Call AV selection.
AV selection
COMP. IN
HDMI2/DVI
HDMI1/DVI
PC IN
AVS
DVD-REC
DVD
VIDEO
OK Switch to ...
OK
56Select PC IN socket,
OK switch over.
Adapt geometry (only possible with certain signals)
This can be used to position the picture correctly and move the position
of the picture (horizontally and vertically) so that it fills out the whole
screen.
Switch off all equipment before connecting.
Call TV menu.
Connect the device to the TV set’s PC IN socket with a VGA
cable.
34Select Geometry,
6go to the menu line below.
Connect the analogue audio signal of the PC to the AUDIO
IN2 jack on the TV set with a stereo cable.
34Select the desired setting,
6 go to the menu line below.
TV set
Connection
example of a
PC
END
34Make settings.
Set colour standard (only possible with certain signals)
PC IN
PC
AUDIO IN2
Call TV menu.
34Select Picture,
6go to the menu line below.
IN
OUT
MIC
DIG-OUT
34Select and set Colour standard:
RGB or
Ycc / Ypp
The colours will not be shown correctly if the wrong
standard is set.
Alternatively, connect the digital audio output of the PC or
accessory equipment to the AUDIO DIGITAL IN socket of
the TV set with a cinch cable.
The digital audio input can be assigned to the PC IN socket
by TV menu → Connections → Miscellaneous → Assign
digital audio input, see page 53.
45 -
Operating additional equipment
Devices to the Component IN connection
Playback from the device
DVD players/recorders or a Set-Top-Box with Component
Video connections can also be connected to the Cb/Pb
Cr/Pr Y sockets (SD/HD-COMPONENT) of the TV set instead
of to the EURO-AV sockets.
The connecting cable with three cinch plugs each transfers the picture
information with a better quality than a EURO-AV cable. You need another
cable for the sound transmission.
Connecting the device
➠D
evice to COMP. IN is registered with the connection
wizard.
Switch off all equipment before connecting.
Connect the Component Video outputs of the external
device by a triple cinch cable to the Cb/Pb Cr/Pr Y sockets
of the TV set.
Connect the analogue audio outputs of the external
device to the AUDIO IN1 L/R sockets of the TV set by a
dual cinch cable.
TV set
Connection
example of a
Set-Top-Box
AV selection
COMP. IN
HDMI2/DVI
HDMI1/DVI
PC IN
AVS
DVD-REC
DVD
VIDEO
OK Switch to ...
OK
Adapt geometry (only possible with certain signals)
This can be used to position the picture correctly and move the position
of the picture (horizontally and vertically) so that it fills out the whole
screen.
Call TV menu.
34Select Geometry,
6go to the menu line below.
34Make settings.
Cb/Pb Cr/Pr Y
Set-Top-Box with
COMPONENT OUT
Alternatively, connect the digital audio output of the external device to the AUDIO DIGITAL IN socket of the TV set
with a cinch cable.
The digital audio input can be assigned to the COMP. IN
socket by TV menu → Connections → Miscellaneous → Assign
digital audio input, see page 53.
END
56Select COMP. IN socket,
OK switch over.
34Select the desired setting,
6 go to the menu line below.
AUDIO IN1 L/R
- 46
Call AV selection.
Operating additional equipment
Sound components wizard
TV speakers
The sound components wizard helps you to configure the components
used to play the TV sound.
Depending on what you want to use, active speakers, speaker systems,
Loewe Individual Sound Projector and analogue and digital HiFi/AV amplifiers can be configured.
The sound components wizard is preset to playback via TV speakers at
the factory.
If a Loewe Preceiver Auro has been connected to the TV set via link
cable, you can only select between TV speakers and Auro in the sound
components wizard.
No TV speakers are included in the scope of delivery for the "Individual
Compose" TV set. Two speakers (min 4 ohm / min. 20 W sinus) can be
connected via the speaker connections (screw terminals) of the TV set.
The Loewe "Stereospeaker I Compose" available as an accessory are ideal
for this. These can be fixed directly to the TV set or separately to the
wall. When fixing the speakers directly to the TV set, the side speaker
connections (exclusively for "Stereospeaker I Compose") behind the trim
are used. In the case of separate wall assembly, the speakers are connected to the screw terminals. See installation instructions "Stereospeaker
I Compose".
Integrated Dolby Digital Decoder
Your TV set is equipped with an integrated Dolby Digital Decoder. This
system has been introduced to the DVD video range and digital TV stations can also broadcast in digital multi-channel sound.
For playback of 5 audio channels the surround sound is reinforced by the
deepest frequencies from the subwoofer channel (SUB), (5.1 reproduction
= 5 audio channels and 1 subwoofer). All 5 audio channels are reproduced
with the full frequency range from 20-20,000 hertz and generate the
original theatre effect.
The Dolby Digital Decoder also decodes dts, MPEG and the analogue
Dolby Pro Logic and Dolby Pro Logic II signals, regardless of whether
the audio signal is transmitted by an external device or received by the
TV set.
DVDs or CDs with PCM coded audio format are also decoded by the
Dolby Digital Decoder. The CD/DVD player must be connected via a
coaxial, digital connection to the digital input AUDIO DIGITAL IN for this
(see page 53).
The audio signals decoded by the Dolby Digital Decoder are output via
the AUDIO LINK interface. You can connect a speaker system such as the Loewe "Individual Sound" (see page 48) or active speakers (see page
49) to the AUDIO LINK interface and configure these with the sound
components wizard.
Speakers must never be connected simultaneously to the side connections
and to the screw terminals.
Settings for speaker systems and active speakers which are connected via
the AUDIO LINK interface to the Dolby Digital Decoder of the TV set:
•
•
•
•
•
Connecting speakers to the screw terminals
To connect the speakers, switch the TV set off at the mains switch and
pull out the mains plug.
You have connected and laid out the connecting cables to the speakers.
Remove the rubber band fixed as a transport protection (see figure).
Turn the 4 screw terminals anti-clockwise about 2 or 3 turns. This frees
the connection openings for the connecting cables of the speakers.
Do not loosen the screw terminals more than necessary. They could
fall down and get lost.
Make sure no bare cable ends can get inside the device when connecting. Avoid short-circuits between the individual screw terminals
and between the screw terminal and the support plate.
Push the connecting cables (max. 1.5mm2) of the speakers under the
respective same coloured screw terminal (red to red, black to black).
See also the printed connection designations of the speakers right
(Right) and left (Left) and the characters "+" equal red and "–" equal
black (see figure).
Make sure that the sheaths of the connecting cables are not clamped
accidentally as well.
Tighten the screw terminals clockwise.
Register speaker (system) or active speaker.
Setting of the lower limit frequency of the speakers.
Setting of the distances between listener and speakers.
Level settings for the speakers.
Setting of the phase position for the subwoofer channel.
All data and selection possibilities which refer to the TV speakers in the
course of the sound components wizard are only relevant when TV speakers
are connected.
Remove transport protection
Attach connection cable
47 -
Operating additional equipment
Speaker system Loewe Individual Sound on
the Dolby Digital Decoder of the TV set
Setup
The arrangement of speakers and TV set can look like the illustration
below:
The front and surround speakers should be installed symmetrically to the
TV set and to your sitting position.
You can place the subwoofer anywhere on the floor. We recommend
placing it in front asymmetrically next to the TV set.
If a centre speaker is used, it should be placed centrally below the TV
set.
For the settings in the sound components wizard enter the distances of
the centre speaker, and the front and surround speakers to your sitting
position. This guarantees a natural spatial image of the sound.
Connecting
Switch off all devices before connecting.
Subwoofer without AUDIO LINK interface (cable represented by grey,
dotted line):
Plug the adapter cable to the AUDIO LINK interface of the TV set. Connect
the cinch connections of the adapter cable to the 6-pin cinch connections
of the subwoofer. Use the 6-pole cinch cable provided with the subwoofer
for this.
The cubic plug cable connects the master connection on the subwoofer
to the cubic plug of the adapter cable.
The adapter and cubic plug cable are available from your dealer (see
Accessories, page 68).
Subwoofer with AUDIO LINK interface:
The subwoofer is connected to the TV set via the AUDIO LINK interface.
Use the AUDIO LINK cable provided with the subwoofer.
➠ If you have connected speakers directly to the TV set, you can use
these as front or centre speakers depending on the setting in the
sound components wizard.
Individual Sound (subwoofer)
➠ If you have not connected any speakers directly to the TV set, the two
front speakers and the centre speaker (Centerspeaker I Compose) are
connected to the subwoofer of the Individual sound system.
ON
Power OUT
R
Surr.
OFF
L
R
Front
C
Bass Intensity
L
Min.
Line IN
AUDIO-LINK
Front
left
Front
right
0
Right Subw. Left
Surr.
Max.
Phase
180
Front
Right Center Left
230V~50/60Hz
Centre
Speaker
L
SL
C
R
cubic plug
cable
SR
Subwoofer
Surround
left
SUB
SR
Master
AUDIO LINK cable
(subwoofer with AUDIO LINK)
adapter cable
(subwoofer without
AUDIO LINK)
SR
R
R
C
C
SUB
SUB
L
L
SL
SL
6-pole cinch
cable
Surround
right
TV set
Setup example for Loewe Individual Sound
- 48
Connecting Loewe Individual Sound (Subwoofer) to the TV set
Operating additional equipment
Connecting other speaker systems or active
speakers to the Dolby Digital Decoder
If you want to use another similar speaker system or active speakers,
you can connect these to the AUDIO LINK interface of the TV set with
an adapter cable.
A comparable speaker system is connected in a similar way to that described above for "subwoofer without AUDIO LINK interface".
The adapter cable is available from your dealer (see Accessories, page 68).
Connecting active speakers
Switch off all devices before connecting.
Plug the adapter cable into the AUDIO LINK interface of the TV set. Connect the cinch connections of the adapter cable to the connections of
the corresponding active speakers.
The cinch connections of the adapter cable are labelled:
R for Front right
L for Front left
C for Centre
SR for Surround right
SL for Surround left
SUB for Subwoofer
The connections on the adapter cable are preamplifier outputs. Therefore,
only active speakers may be connected directly to the adapter cable.
Front
left
Front
right
Centre
Adjusting the speaker system
Calling the sound components wizard
➠ In normal TV mode, without other displays.
Call TV menu.
34Select Connections,
6go to the menu line below.
34Select Sound components,
OK calls the sound components wizard.
Sound components wizard
Please specify here via which sound components you want to listen to your
TV sound. If you select a "Speaker system", this must be connected to the
AUDIO LINK socket on the back of the TV set (with an additional adapter if
necessary).
If your TV has no built-in speakers, the sections relating to "TV speakers“ may
not be selected.
Sound components
Sound playback via ...
TV speakers
Speakers system
HiFi/AV amplifier
Sound projector
HiFi/AV amplifier or TV speaker (switchable)
Sound projector or TV speaker (switchable)
OK Proceed

OK
END
Sound playback via ... speakers system
Enter here that you want to hear the TV sound over a speaker system.
If you connect active speakers, please use the setting Speakers system.
Mark Speakers system,
OK to continue.
Subwoofer
Sound components wizard
Please specify whether you want to change the illustrated setting of your
speakers system or whether all existing settings are to be reset to the values
of the delivery state.
Components
Distances
Level
L
C
SUB
R
SR
C
SUB
R
SR
SL
L
SL
TV
Surround
left
TV
Surround
right
Sound components
Speakers system
Configuration/modification
Adapter cable
OK
TV set
Connection of active speakers to the TV set
TV
4,0m
OK
TV
4,0m
TV
0dB
TV
0dB
Reset to factory settings
END
Proceed
If nothing has been set yet, the factory settings or otherwise the last set values are displayed.
continued on the next page
Ž
49 -
Operating additional equipment
If you want to set up or change a speaker system:
➠ S elect the start value of the frequency response of the
speakers for the right setting (e.g. 50Hz for the
specification "Frequency response 50-20.000Hz"). See
the technical data of the speakers for the value.
34Select Configuration/modification,
OKcall selection.
Sound components wizard
Please specify here whether you want to completely reconfigure a speakers
system or whether you want to limit the configuration to changing the
speaker connections, the speaker distances from the listening position or
the individual speaker levels in relation to each other.
➠Y
ou can replace the external front speakers by the TV
speakers if necessary. In this case, select TV speakers.
Then transmit the sound of the front speakers.
OKcontinue to connect and set the surround speakers.
34Select yes for external speakers.
Sound components
Configuration/modification of speaker system
Complete
Connections only
Distances only
Levels only
OK
OK
END
Proceed
Select Complete,
OK continue to connect and set the front speakers.
Sound components wizard
Please specify here whether you want to connect
external front speakers. In this case, their lower
limit frequency must be entered in Hz (see
instruction manual and technical data of the
speakers).
TV speakers
40Hz
➠ S elect the start value of the frequency response of the
speakers for the right setting.
OK continue to connect and set the centre speaker.
34Select whether the TV speakers or an External
speaker is to reproduce the centre sound or no if
no centre speaker is connected.
➠ If no centre speaker is connected, the front speakers
also transmit the centre sound parts additionally.
TV speakers
Proceed
END
34Select External speakers,
go to the menu line below and
34set the lower limit frequency of the front speakers
in 10 Hz steps.
Sound components wizard
Please specify here whether you want to connect
external front speakers. In this case, their lower
limit frequency must be entered in Hz (see
instruction manual and technical data of the
speakers).
Go to the menu line below and
34set the lower limit frequency of the surround
speakers in 10 Hz steps.
40Hz
Sound components
Connect front speakers
External speakers
40 Hz
OK
➠ If no surround speakers are connected, these can be
simulated using the front and centre speakers.
70Hz
70Hz

for External speakers or TV speakers go to the
menu line below and
34set the lower limit frequency of the centre speaker
in 10 Hz steps.
➠ S elect the start value of the frequency response of the
speakers for the right setting.
OK continue to connect the Subwoofer.
34yes is the selection for subwoofer.
➠ If no subwoofer is connected, the front speakers
additionally transmit the sound parts intended for the
subwoofer as far as possible.
Sound components
Connect front speakers
External speakers
70 Hz
OK
Proceed
END
Ž
continued on the next page
- 50
Operating additional equipment
OKcontinue to set the
Distance to left front speaker.
OK continue to Subwoofer phase.
➠M
easure the distances from your listening position to
the front, surround, and centre speakers respectively.
The Dolby Digital Decoder calculates the delay times
for the speaker signals from these so that they reach
the listener simultaneously.
Sound components wizard
Please enter the distance of the left front
speaker from your listening position here.
4,2m
2,7m
1,0m
Sound components wizard
Here you can reverse the phase of your subwoofer. Test both values in music
reproduction and then select the one with which you get a better bass
reproduction.
4,0m
Sound components
Subwoofer phase
0°
OK Proceed
0,9m
180°
END
Switch to a station with music with P+/P– or start playback
with music on a DVD player.
Sound components
Distance to left front speaker
4,2 m
OK Proceed
END
34Test both values (0º and 180º) and select the one
with which you get a clearer bass reproduction
from your listening position.
OK to confirm the setting and exit the wizard.
34Set the distance between the left front speaker
and your listening position in 10 cm steps.
OK continue respectively to the other speakers and
34adjust the distance.
This ends the sound components wizard for connecting
and setting up a speakers system.
➠ After setting the distance for the centre speaker ...
OK continue to Adjust speaker level.
Sound components wizard
You hear a sound from every speaker one after
another. But you can also select the speakers
manually with the menu control buttons up/down.
Set the volume for the respectively active speaker
shown in blue so that you get approximately the
same volume impression from all the speakers.
Sound components
Adjust speaker level
0 dB
OK Proceed
0dB
0dB
0dB
0dB
END
Preceding/next loudspeaker
34Adjust the volume for each speaker.
Select speakers manually.
➠ F or balanced audio reproduction all speakers should be
set at the same volume level. A noise signal will be
reproduced automatically on each speaker in succession.
Adjust every speaker to equal perceived volume from
your listening position.
51 -
Operating additional equipment
Connecting audio amplifiers
Connecting digital audio amplifiers
The sound components wizard permits configuration of different audio
amplifiers (stereo amplifiers, surround amplifiers, analogue or digital) with
different digital audio formats (Dolby Digital, dts, MPEG, and stereo/PCM).
See the operating manual of the audio amplifier for more information.
Call TV menu.
Continuation of the left column above ...
For digital audio transmission: Select yes.
Connect the digital audio output of the TV set AUDIO
DIGITAL OUT with the digital audio input of the amplifier
via a cinch cable:
34Select Connections,
6 go to the menu line below.
34Select Sound components.
TV set
AUDIO DIGITAL OUT
OK calls the sound components wizard
Mark the HiFi/AV amplifier.
PREOUT
FL
Sound components
Sound playback via ...
TV speakers
Speakers system
HiFi/AV amplifier
Sound projector
HiFi/AV amplifier or TV speaker (switchable)
Sound projector or TV speaker (switchable)
OK Proceed
FR
AUX1 IN AUX OUT AUX 2
L
L
SR
R
DIGITAL
IN
SL

SUB
DIGITAL
OUT
R
Digital amplifier
OK
END
OK Proceed.
34Select whether the sound is to be transmitted
digitally or analogue to the the amplifier.
Continue, depending on the amplifier, see right column.
Explanations of the setting possibilities:
HiFi/AV Select setting if an amplifier is connected and your TV set
amplifier does not have any TV speakers connected.
HiFi/AV
amplifier or TV
speakers
(switchable)
C
Sound formats, amplifier type and other settings, see
explanations of the setting possibilities (left hand
column).
Connecting analogue audio amplifiers
Continuation of the left column above ...
For digital audio transmission: Select no.
Connect the analogue audio output of the TV device
AUDIO OUT L/R via a stereo cinch cable to the analogue
audio input of the amplifier:
Select setting if an amplifier is connected and your TV set
has TV speakers connected. In the sound mode selection
the sound reproduction can then be switched back and
forth between the amplifier and the TV speakers.
AUDIO OUT L/R
TV set
Sound formats Specify sound formats which can be decoded with the digital
amplifier (see operating manual of the used amplifier).
PREOUT
Type of Select either stereo or surround amplifier.
amplifier
TV loudsp. as For every connected surround amplifier, select whether
centre speaker the TV loudspeakers are to be used as centre speaker.
If so, establish a connection between the centre output
of the amplifier and the centre input of the TV set AUDIO
IN1 C with a cinch cable.
Attention: Do not use the centre speaker connection of the
amplifier, use the centre pre-amp output instead!
- 52
FL
C
FR
AUX1 IN AUX OUT AUX 2
L
L
SR
R
DIGITAL
IN
SL
SUB
DIGITAL
OUT
R
Analogue amplifier
For selecting the amplifier type and making other settings,
see explanations of the setting possibilities (left hand
column).
Operating additional equipment
Assignment of the digital audio input
TV set
In order to be able to hear the digital sound of an external device connected to an AV input, an AV input can be assigned to the digital audio
input socket AUDIO DIGITAL IN. When switching to this AV input, the
digital audio signal applied to the AUDIO DIGITAL IN input is passed on to
the integrated Dolby Digital Decoder and the digital audio output socket
AUDIO DIGITAL OUT. You will then hear the digital sound of the assigned
AV input instead of the analogue sound if available.
Connecting devices to the digital audio input
For the digital audio playback from an external device, e.g. the DVD player,
you have to feed the digital audio signal to the TV set.
The external digital audio signal can be played back via the integrated
Dolby Digital Decoder in the TV set, via an externally connected digital
audio amplifier, Loewe Individual Sound Projector or Loewe Auro.
➠ If an external audio amplifier or Loewe Individual Sound
Projector is used, this must be registered in the sound
components wizard (see page 52).
Call TV menu.
34Select Miscellaneous,
6 go to the menu line below.
34Select Assign digital audio input,
6 go to the menu line below.
34Select AV input.
no
INFO
to AV2
to AVS
DVD player
The DVD player is already registered at AV1 in the connection
wizard at the factory.
If new devices are connected and registered in the
connection wizard, the digital audio input AUDIO DIGITAL
IN is assigned in the connection wizard (see page 41).
Audio connection in HDMI (DVI) devices
External devices with DVI connection
If an external device with DVI interface is connected via a HDMI/DVI
adapter to the HDMI1/DVI or HDMI2/DVI socket of the TV set, you can
connect the digital sound of the external device to the digital audio input
socket AUDIO DIGITAL IN.
The assignment of the digital audio input to the corresponding HDMI
socket of the TV set takes place as described in the column on the left.
If you want to use the analogue sound of the external device, connect
it to the AUDIO IN1 socket.
34Select Connections,
6 go to the menu line below.
TV menu
Connections
Miscellaneous
Assign digital audio input
to AV1
AUDIO DIGITAL IN
AV1
to HDMI1/DVI
END
to HDMI1/DVI
To connect a DVD player to the digital audio input of the
TV set for example, connect the digital output socket of
the DVD player (DIGITAL OUT) via a cinch cable to the
AUDIO DIGITAL IN socket on the TV set.
External devices with HDMI connection
If external devices with HDMI interface are connected to the HDMI1/DVI
or HDMI2/DVI socket of the TV set, no assignment of the audio input is
necessary because the digital transmission of picture and sound takes
place via one connection in HDMI.
RS-232C interface
You can connect either the Loewe Individual Sound Projector or a home
network system of different manufacturers (e.g. AMX, Crestron) to your
TV set via the RS-232C interface.
Please consult your dealer for configuration of the RS-232C interface and
further information about the different home networking systems.
53 -
Operating additional equipment
The direct way to record
You can programme timer recordings via the integrated Digital Recorder
or connected recorders on the TV set. The recording wizard is integrated
at several places for programming a recording. Further information
about recording with the Digital Recorder can be found in a separate
operating manual.
Programming a timer recording with the EPG
➠Y
ou are in EPG mode; if not, press the EPG button.
EPG (Electronic Programme Guide)
Date
Time
Stations
Topics
Mon 31.07.
now
until 17:00
17:00
18:00
19:00
all
all
arte
15:57-16:59 Charmed - Zauberhafte Hexen OK
Das Erste
16:00-16:10 Tagesschau
ZDF
16:00-16:10 heute - in Europa
WDR Köln
16:00-16:15 WDR aktuell
Bayerisches... 16:00-16:05 Rundschau
hr-fernsehen 16:00-16:30 Schlemmerreise Spanien
MDR FERNS... 16:00-16:15 Hier ab vier
NDR FS HH
16:00-16:30 Tipps und Trends - Der Verbraucher...
SWR Fernse... 16:00-16:05 Baden-Württemberg aktuell
Charmed - Zauberhafte Hexen 
2 ZDF
TEXT
P+
P–
Detail
Page ↑↓
Mon 31.07./16:05
OK
0
-
9
View
Select time
Record
Select date, ... , topics
END
MENU
65Mark the desired broadcast.
Enter timer data
Timer data are displayed after selecting the programme
you want to record. You can change these before
confirming.
Timer data
12.00 Brisant
Recorder
Station
Date
Recording time
VPS
Recording type
Switch recorder to
OK confirm
DVD-REC
01 Das Erste
14.09.2006
17.15 until 17.45
no
once only
AUX!
OK
DR
END
INFO
OKconfirms Timer data,
or change if necessary:
34Select Recorder.
Select Date.
Enter the recording date with the numeric buttons.
Select Recording time.
Enter the recording time with the numeric buttons.
Select VPS.

34Set yes/no.
Select Recording type.
34Set once only, Mon-Fri, daily, weekly.
Red button: Call Timer data.
Change or confirm Timer data as necessary.
OK Confirm the Timer data.
Programming a timer recording via teletext
➠Y
ou are in teletext mode; if not, press the TEXT button.
301
302
ARDtext
Do
Do
14.00
14.10
19.20
–
09: 36 : 42
14. 09. 06
Das Erste
Tagesschau
In aller Freundschaft UT . . . . . . . . . . .
Zweite Begegnung (D, 2005)
Tagesschau
Sturm der Liebe (221) . . . . . . . . . . . . .
Tagesschau UT
Eisbär, Affe & Co. . . . . . . . . . . . . . . .
Tagesschau um fünf UT
Brisant . . . . . . . . . . . . . . . . . . . . . . .
Tagesschau
Verbotene Liebe . . . . . . . . . . . . . . . .
Marienhof . . . . . . . . . . . . . . . . . . . . .
Das Geheimnis meines . . . . . . . . . . . .
Vaters (19)
Das Quiz mit Jörg Pilawa . . . . . . . . . .
bis 19.50 Uhr
15.00
15.10
16.00
16.10
17.00
17.15
17.47
17.55
18.20
18.50
300 <<
14. 09. 06
+
317
318
319
320
321
322
384
OK
Record
Call the programme pages of the current station.
Change preset page numbers, see page 33.
Green button: Go to the appropriate page.
65Select desired broadcast,
OK calls Timer data.
Change or confirm Timer data as necessary.
- 54
Recorder Selection of the connected/integrated recorder.
Date Day of recording.
Recording time Time of recording.
VPS Use VPS data, yes/no.
(Some stations do not broadcast a VPS signal).
Recording type once, Mon–Fri, daily or weekly.
In timer recordings via EPG, Serial can also be selected.
Abend > 303
ARD morgen
Jetzt im TV
Select programme
316
Setting possibilities in the Timer data menu:
➠ If you use an external recorder without Digital Link Plus, you have to
select the recording source in the recorder (e.g. AUX). This is also the
case when DVB programmes are to be recorded. The TV's receiver
is used.
➠ If you use an external recorder with Digital Link Plus or a comparable
system (e.g. P50), this is controlled automatically.
Operating additional equipment
Timer recording with external devices
Programming the timer with the timer overview
A timer recording can also be programmed manually.
➠ It is not possible to record HDTV broadcasts with external devices. Use
the internal Digital Recorder for this.
Call Timer list.
You see a list of all previously programmed timers:
Timer list
Mon 14.09.
Wed 16.09.
Thu 22.09.
17:15-17:45
14:00-15:50
20:15-22:25
Das Erste
ZDF
3sat
Recorder with Digital Link Plus
If you use an externally connected recorder with Digital Link Plus or a similar
system, the TV set and connected recorder exchange data (e.g. compare
station lists TV set/recorder or timer data of analogue stations).
Please consult the operating manual of your recorder to find out if your
recorder is Digital Link Plus compatible. In addition use only Euro AV
cables for the connection between TV set and recorder.
Mon 31.07./11:28
Brisant
Biathlon-Weltcup
wissen spezial
---New recording
Change
Delete
END
INFO
Green button: Change timer recording.
Yellow button: Delete timer recording.
Red button:
New timer recording.
Programming the timer manually
➠ The timer list is open.
Red button: Call the recording wizard.
Recording wizard
Via EPG
INFO
OK
Via teletext
END
Manual
34Select Manual,
OK call Station selection.
34 Select station.
OK calls the Timer data.
For timer data input, see page 54.
After confirming the timer data, the new recording is
transferred to the timer overview.
Explanation of the setting possibilities of the recording wizard:
Via EPG Timer programming via EPG (see Programming a timer
recording with the EPG, page 54).
Via Teletext Timer programming via Teletext (see Programming a timer
recording via Teletext, page 54).
Manual Programming timer manually (see above).
Analogue stations
The timer data are transmitted automatically from the TV set to
the recorder after programming is complete. (For DVD recorders
in addition the recording quality SQ or EQ is also transmitted.)
The recording then is controlled by the recorder and the recorder
tuner is used for reception of the programme.
The recording data are not saved in the timer overview of the TV
set. Consequently if you want to change or delete the timer data
then you must do so on the recorder.
Digital stations
If you want to record digital stations with an externally connected
recorder, then the DVB tuner is used and the TV device takes over
control of the recorder. Then the station on the TV set is locked
during the timer recording. It is not possible to switch over to
another DVB station.
Recorder without Digital Link Plus
If the programmed timer cannot be transmitted to the external recorder
(no Digital Link Plus) but supports Digital Link (Loewe-own system), the
TV receiver is always used.
Digital Link must be switched on on the recorder. Read the operating
instructions of your Loewe recorder.
In addition use only Euro AV cables for the connection between TV set
and recorder.
Analogue and digital stations
You can control the recording from the TV set. The recorder must be
set manually to the AV input, to which the TV device is connected.
Then the station on the TV set is locked during the timer recording.
It is not possible to switch over to another station.
Copy protection
Copy-protected programmes will not be output on the EURO AV sockets
for legal reasons.
55 -
Operating additional equipment
PhotoViewer
You can view photos in the standard JPEG format stored on a USB stick or a
memory card in a card reader. You can also collect photos in a slide show.
Viewing photos
➠ The photo overview is displayed.
Folder_1
Connecting
OK
➠C
ertain USB memory media may not be supported by this set under
some circumstances.
Plug a card reader (via a USB cable) or a USB stick into the USB port on
the TV set (see pages 5 and 6).
Use a USB extension cable (available from your dealer) for the USB stick
if the USB socket is difficult to access (e.g. wall mounting) or the USB
stick is too big to be plugged in.
To mount the cover, break out the cable opening in the cover flap.
Starting the PhotoViewer
USB 1:\picture_024.jpg
OK
View picture
Mark picture
38 pictures
P+
P–
Slide show
scroll ↓↑ (1/3)
END
MENU
INFO
5634Mark a photo, page with P+/P– if necessary.
OK Display as full picture.
➠N
o photos can be displayed which are available in progressive JPEG
format.
A memory card or the USB stick should contain data in standard JPEG
format with the file extension ".jpg".
Call the Assist+ menu.
56Mark PhotoViewer,
OK continue.
If only one memory medium is available, the PhotoViewer
is started. You see the first page of the photo overview
(see right column).
If several media are available, select with
34memory medium and then with
OK start PhotoViewer.
Ending the PhotoViewer
Remove used memory medium.
Or:
Press END button (when photo list is displayed).
Or:
Press TV or RADIO button.
Or:
Press the ASSIST button and call another function in the
Assist+ menu.
- 56
or P+ Next photo.
or P– Previous photo.
END: Show/hide photo information.
Yellow button: Zoom photo.
Enlargement factors x2, x4, and x8 are possible.
Press the button several times.
The 4th press returns you to the original size.
Select photo section in zoom mode with 5634.
Exit the zoom mode to the photo overview with OK or
the STOP button.
34Rotate picture by 90 degrees to the left/right.
➠ P hotos displayed in a slide show can only be rotated
in the Pause mode for viewing.
OK or STOP button: Back to the photo overview.
Operating additional equipment
Open folder
➠ Folders will only be displayed if they were created on
the memory card / USB stick.
Calling the PhotoViewer menu
In the PhotoViewer menu you can make picture settings and select the
memory medium.
➠ The photo overview is displayed.
5634Mark a folder in the photo overview.
OK Open folder.
The photos in this folder are displayed.
Call PhotoViewer menu.
Ordner_1
OK
OK
USB 1:\Folder _1\
OK
Open folder
29 pictures
P+
P–
Slide show
scroll ↓↑ (1/2)
END
MENU
OK
View picture
Unmark picture
29 pictures
P+
P–
Slide show (marked pictures)
MENU
scroll ↓↑ (1/2)
END
INFO
Blue button: Mark photo for slide show.
Starting a slide show
➠N
o photos marked: All photos of the folder that was
just opened will be displayed.
➠ Photos marked: Only marked photos will be displayed.
PLAY button: Start / continue slide show.
OK calls the photo overview.
PAUSE button: Pause / continue the slide show.
Yellow button: Zoom picture (only in pause mode).
34Rotate picture to left/right in 90º increments (only in
pause mode).
or P+ Next photo.
or P– Previous photo.
STOP button: End slide show.
...
Picture change
END
Picture crossovers
Explanations of the setting possibilities:
Go to... Within the folder select a photo directly or go to the
beginning or end of the folder.
5463Navigate to a photo.
OK
INFO
Picture display
INFO
Marking photos for slide show
Mark the photos that you want to display in a slide show.
USB 1:\Folder_1\picture_017.jpg
PhotoViewer menu
Go to ...
Picture 001
Picture display With Optimum size the photo is reduced or enlarged in
size so that the screen is optimally filled.
With Original resolution each pixel of the photo represents
one pixel on the screen. If the photo resolution is higher
than that of the screen, then portions of the photo will
be cropped.
Picture change Set the display time per photo in a slide show to between
3 and 60 seconds.
The loading time of the photo depends on the photo size,
the number of saved files and the transmission speed of
the memory medium. Therefore a photo change may
take longer than specified.
Picture There is a choice of four different photo transitions for
crossovers changing slides. You can also have the photo transitions
run in sequence.
Photo info Display additional information about the picture: Recording
time and date, resolution and picture size.
Picture settings Set picture adjustment, contrast, colour intensity, colour
temperature, brightness, sharpness, DNC.
Sound Select whether or not the previously heard sound is to
be heard during the PhotoViewer operation.
Select memory Select memory medium from which the photos are to be
medium reproduced. This menu item is only displayed if at least
two memory media are available.
57 -
Operating additional equipment
MusicBox
You can play music files in MP3 format which are saved on a USB stick
or a memory card in a card reader. You can also collect the music titles
in play lists.
Connection
➠C
ertain USB memory media may not be supported by this device.
➠Y
our memory medium should not exceed a total capacity of 8 GB. Larger
memory media may not be supported. The read-in time of the memory
medium depends on the stored data volume.
➠ T he file names must have the extension ".mp3". Alternative specifications
such as MP3 Surround or similar are not supported.
Plug a card reader (with a USB cable) or a USB stick into the USB port on
the TV set (see page 5 and 6).
Starting the MusicBox
Call Assist+ menu.
56Mark MusicBox,
OK continue.
If there is only one memory medium the MusicBox is
started with the MusicBox list (see right column).
If several media are available select memory medium with
34and then with
OK start MusicBox.
Ending the MusicBox
Remove used memory medium.
Or:
Press END button (while status window is displayed)
Or:
Press TV or RADIO button.
Or:
Press the ASSIST button and call another function in the
Assist+ menu.
➠ If the MusicBox is ended during playback, the MusicBox
remembers the appropriate place in the title. If the TV
set is not switched off or the memory medium removed
in the meantime, the playback continues at this point
the next time the MusicBox is called. The MusicBox
then starts immediately on the MusicBox status window
(see right column).
- 58
Select/play music
After starting the MusicBox, the content of the memory medium, the
MusicBox list, is displayed.
MusicBox
Files
Backup
MP3
Photo
Video
OK
USB 1:\
Open folder
Play lists
Browse/sort
OK
END
INFO
MENU
56Mark folder, scroll with P+/P- if necessary,
OKopen selected folder.
You see the music files (titles) and/or sub-folders
in the opened folder.
One folder level back:
Select
... and press OK.
MusicBox
Files
..
Title_01.mp3
Title_02.mp3
Title_03.mp3
Title_04.mp3
Title_05.mp3
Title_06.mp3
Title_07.mp3
Title_08.mp3
Title_09.mp3
Title_10.mp3
Title_11.mp3
OK
P+
P-
OK
USB 1:\MP3
play back
Page 
Play lists
Browse/sort
END
INFO
MENU
56Mark title, scroll with P+/P- if necessary,
OKplay marked title.
Then the MusicBox status window opens with
information about the played title.
➠ If the file contains additional information (ID3 tags), the
title, singer, album title etc. are displayed.
MusicBox

„Chasing Cars“
Artist:
Album:
Playtime:
Volume
OK
INFO
Stereo
2
Snow Patrol
Eyes Open
1:23 / 4:28
30
MusicBox list
Detail off
Screen off/on
END
MENU
Operating additional equipment
Functions of the control buttons
Sort according to artists
MusicBox
STOP button: Once: resume stop, twice: stop.
Savatage
Sido
Sinatra Frank
Starship
Steel Pulse
System Of A Down
Texas Lightning
Thin Lizzy
PLAY button:
After resume stop: Continue playing at place where
playback was interrupted.
After stop: Start playing the first title according to the set
sorting.
For playback: Start the current title from the beginning.
For pause: Continue playback.
OK
TEXT
P+
P-

Short: previous title, long: rewind.
Settings in the MusicBox status window
Red button: Switch off TV screen.
Press red button, INFO or OK to switch back on.

INFO
You can browse or sort the contents of your memory medium with the
coloured buttons according to certain criteria (file names, titles, artists,
albums).
➠ The MusicBox list is displayed.
INFO
Sorting according to albums
Blue button: Show All Albums.
All available albums are sorted alphabetically by ID3 tags
and displayed with the appropriate artist.
56Mark album and select with OK.
56Select title in album and play with
OK in MusicBox status window.
Blue button: Call Browse/sort.
The MusicBox overview is sorted according to Files at the
MusicBox
Files
beginning.
The sorting is based on the file names
of the
Browse/sort
music files
.. regardless of their ID3 tags.
Track_01.mp3
Track_02.mp3
56Select
file/folder and play/open with OK.
Track_03.mp3
Track_04.mp3
Track_05.mp3
Track_06.mp3
Track_07.mp3
Track_08.mp3
Track_09.mp3
Track_10.mp3
USB 1:\MP3
play back
Page 
END
MENU
Yellow button: Show All Titles.
All available titles are sorted alphabetically by ID3 tags and
displayed with the appropriate artist.
56Select title and play with
OK in MusicBox status window.
MusicBox – Browse/sort
OK
All Titles
All Albums
Sorting according to titles
OK Show MusicBox list.
P+
P-
Files
Select letter
TEXT: Call Titles by ...
The titles of the selected artist are displayed sorted alphabetically.
56Select title and play with
OK in MusicBox status window.
Reduce info window to one line / maximise again.
Stereo 2
a - z
OK Call Albums by ...
The albums of the selected artist are displayed sorted
alphabetically.
56Mark album and select with OK.
56Select title in album and play with
OK in MusicBox status window.
Short: next title, long: wind.
„Chasing Cars“
Albums by ...
Titles by ...
Page 
OK
56M
ark artist, scroll with P+/P- if necessary or enter the
initial letter with numeric buttons like a mobile phone
keypad (see page 15).
PAUSE button: Pause / continue playback.
MusicBox
Artists
Browse/sort Show Artists.
Green button:
Rage
All music
are sorted alphabetically according to
Richie titles
Lionel
Stones
artists Rolling
(ID3 tags).
Run DMC
➠ Title is played.
Sorting according to files
Red button: Show file overview.
OK
Artists
All Titles
All Albums
END
MENU
INFO
Exit sorting
Exit search/sorting. The new sorting is retained in the
MusicBox list.
59 -
Operating additional equipment
MusicBox – Play lists
Create new play list / add title
You can save and call your music titles in play lists. Change and create
play lists as you like.
The play lists are created on the memory medium in the common M3U
format for simple exchange with the PC.
Call / play play list
➠ The play list overview is displayed.
➠ List selection (left column) must be selected.
If not, change the column with 3.
Blue button: Call Create play list.
A new empty play list is created. The file selection is
visible on the left.
➠ The MusicBox list is displayed.
Build/change play lists
Files
Abba
ACDC
Elton John
Eros Ramazzotti
Rolling Stones
Title_1.mp3
Title_2.mp3
Title_3.mp3
Title_4.mp3
Title_5.mp3
Title_6.mp3
Title_7.mp3
Red button: Call Play lists.
Play lists
Alternative
Instrumental
Jazz & Funk
Metal
Oldies
R’n’B / HipHop
Reggae / Ska
Rock
Playlist 1
Playlist 10
Playlist 11
Playlist 12
Playlist 13
OK
OK
P+
P-
Page 
1
2
3
4
5
6
7
8
9
10
11
12
13
Start play list
MusicBox list
Bolero
All Night Long
Burn
All The Small Things
Summer In The City
In The Mood
Rocket Man
Fight For Your Right
Paint It Black
Me And Bobby Mc...
Can’t Buy Me Love
No Woman No Cry
Bad Moon Rising
Maurice Ravel
Lionel Richie
Deep Purple
Blink 182
Joe Cocker
Glenn Miller
Elton John
Beastie Boys
Rolling Stones
Janis Joplin
The Beatles
Bob Marley
CCR
OK
P+
P-
Change play list
Delete play list
Create play list
END
INFO
In the play list overview you see the created play lists on
the left hand side of the dialogue. On the right next to it
you see the music files in the marked play list.
56S elect play list, scroll with P+/P- if necessary.
OK The play list is played in the MusicBox status
window starting with the first title. The name of
the play list is displayed after the title.
OK
P+
P-
Page 
0
-
9
Start play list
Select title
MusicBox list
Bolero
All Night Long
Burn
All The Small Things
Summer In The City
In The Mood
Rocket Man
Fight For Your Right
Paint It Black
Me And Bobby Mc...
Can’t Buy Me Love
No Woman No Cry
Bad Moon Rising
Maurice Ravel
Lionel Richie
Deep Purple
Blink 182
Joe Cocker
Glenn Miller
Elton John
Beastie Boys
Rolling Stones
Janis Joplin
The Beatles
Bob Marley
CCR
Change play list
Delete play list
Create play list
- 60
END
INFO
56Mark title/folder, scroll with P+/P- if necessary,
OKAdopt marked title to play list or open marked
folder.
Yellow button: Adopt marked folder to play list.
Change play lists
You can adapt the play lists as required. It is possible to move the titles in
the play lists or remove them from the list. The play list can be renamed
or deleted completely.
4Go to the page of the play list (right column).
Build/change play lists
Files
Abba
ACDC
Elton John
Eros Ramazzotti
Rolling Stones
Title_1.mp3
Title_2.mp3
Title_3.mp3
Title_4.mp3
Title_5.mp3
Title_6.mp3
Title_7.mp3
OK
END
INFO
OK
56Select title, scroll with P+/P- if necessary,
OK the play list is played in the MusicBox status
window from the marked title.
Next play list
Browse/sort
Green button: Call Change play list.
Play lists
1
2
3
4
5
6
7
8
9
10
11
12
13
OK
➠ The play list overview is displayed.
OK The play list is displayed again.
4 Change from list selection to title selection.
Alternative
Instrumental
Jazz & Funk
Metal
Oldies
R’n’B / HipHop
Reggae / Ska
Rock
Playlist 1
Playlist 10
Playlist 11
Playlist 12
Playlist 13
Open folder
Adopt to play list
Page 
Playlist14
P+
P-
Remove from play list
Page 
Clear play list
Playliste10
1 Lay it Down
OK
2 Fallin’
3 Do that to Me One More...
4 Hero
5 Insatiable
6 There You’ll Be
7 Let’s Wait a While
8 What If
9 Stillness of Heart
10 Free-One
11 Stop Crying Your Heart
12 Separate Lives
Next play list
Move title
Rename play list
Green button: Select play list to be changed.
END
INFO
Operating additional equipment
Rename play lists
➠ P lay list (right column) must be selected. If not, change
column with4.
Blue button: Starts Rename play list.
Numeric buttons: Enter new name (same procedure as for
rename station, see page 26).
OK Save new name.
Move titles in the play lists / change order
➠ Play
list (right column) must be selected.
56Mark title to be moved.
Yellow button: Starts Move title.
56Select insertion position at which the marked title
is to be inserted.
OK Move title.
Remove titles from play lists / clear play list
➠ Play
list (right column) must be selected.
56Mark title to be deleted.
OK Remove marked title from play list.
Or:
Red button: Starts Clear play list.
OK Confirm clearing play list.
MusicBox – Menu
In the MusicBox menu you make sound settings, can select the memory
medium and set the repeat mode.
➠ MusicBox must be activated.
Call MusicBox menu.
MusicBox menu
Select memory medium
USB1
INFO
...
Sound
Explanations of the setting options:
Select Select memory medium from which the audio files are to
memory be used. This menu item is only displayed if at least two
medium memory media are available.
Sound The settings correspond to the sound settings in TV mode
(see page 20).
Repeat Titles can be repeated in two ways:
Title :
Only the played title is repeated.
Folder or Play list :
Only the titles from the currently selected folder or, if play
list is activated, the current list are repeated.
Repeating is endless until the function is switched off in
the MusicBox menu.
The appropriate symbols for the repetition are displayed
in the top right of the info window.
MusicBox

17 „Chasing Cars“ (Playlist1)
Delete play list from memory medium
➠ T he play list overview is displayed.
56Mark play list to be deleted.
END
Repeat
Artist:
Album:
Playtime:
Stereo
2
Snow Patrol
Eyes Open
1:23 / 4:28
Lautstärke 30
OK
INFO
MusicBox list
Detail off
Screen off/on
END
MENU
Yellow button: Starts Delete play list.
OK Confirm delete play list.
Exit play list overview
➠ The play list overview is displayed.
Red button: Call MusicBox list.
Or:
END: Call MusicBox status window.
61 -
Operating additional equipment
Operating Loewe equipment
Using the remote control for the TV mode of the TV set
Press the TV button, the display above it will light for
approx. 5 seconds.
Using the remote control for a recorder
Press the REC button, the display above it will light for
approx. 5 seconds.
1
2
3
4
5
6
17
18
19
20
Using the remote control for a DVD player
21
Press the DVD button, the display above it will light for
approx. 5 seconds.
Using the remote control for the radio mode of the TV set
Press the RADIO button, the display above it will light for
approx. 5 seconds.
As long as a button is pressed, the display of the selected operating
mode lights up (TV – REC – DVD – RADIO). This allows you to check
which operating mode the remote control is set to every time you press
a button.
7
8
9
22
23
24
25
26
Setting the remote control to other Loewe devices
The specified button combination must be kept pressed (for approx. 5 s)
until one of the LEDs flashes twice.
10
27
11
28
12
29
30
31
Device
Loewe TV +
Loewe Centros 1102 / 1172 +
Loewe Centros 2102 HD / ViewVision
+
Loewe ViewVision DR+ / DVB-T
+
Loewe ViewVision 8106 H
+
Loewe Auro 2216 PS / 8116 DT
+
Loewe Xemix 6222 PS
+
Button combination


14
15
16

The devices marked by  are preset in the remote control supplied with
the TV set.
- 62
13
32
33
Operating additional equipment
Functions for the Loewe DVD player (Auro 2216 PS, 8116 DT)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
Sound off/on
LED indicator for current operating mode
Switch over to operate TV set
Switch over to operate Recorder
Sleep timer
Set TV picture format; RADIO: Mono/Stereo
DISC: Repeat; RADIO: display RDS name/frequency of station
DISC: User interface of loaded DVD
Show/hide menu; MENU: close window
V–/V+ Volume down/up
DISC: Title/Chapter overview; RADIO: station table
MENU: confirm menu selection
Green button: Title/Chapter selection
Red button: DISC: camera position
DISC: short: beginning of chapter/title previous chapter;
long: search back;
RADIO: short: fine tuning back long: search back
no function
Pause; single frame; slow motion
Switch on/off - on stand by
short: TV Radio Digital; long: Auro FM/AM-Radio
Switch over to operate Auro
Select sound format
DISC: select chapter/title; RADIO: select stored station;
MENU: enter digits
MENU: enter numbers or letters
DISC: Repeat A-B; RADIO: FM/AM-mode
Select external audio source
DISC: menu bar
MENU: context help
DISC: Status display; RADIO: station table
MENU: hide menu
P+/P– DISC: next/previous chapter; RADIO: station forward/back
56 DISC: chapter up/down; MENU: select up/down;
34 DISC: search back/forward; MENU: select left/rigt
Yellow button: Zoom
Blue button: Set marker
Playback
DISC: short: next chapter/title; long: search forward
RADIO: short: fine tuning forward; long: search forward
Stop
Functions for the Loewe DVD recorder (Centros 1202, 2102 HD, ViewVision DR+)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
TV Sound off/on
LED indicator for current operating mode
Switch over to operate TV set
Switch over to operate Recorder
Timer recording menu; timer recording list menu
STOP: Title List; PLAY: Edit thumbnail;
CARD: Photo-, Music-, Film-Mode
ViewVision DR+: Timeshift Mode
STOP: Call AV selection (AV1-AV4,DV,TV)
ViewVision DR+: PLAY: skip 15 Sec.
User interface of loaded DVD
MENU: original / playlist
Show/hide menu
V–/V+ TV Volume down/up
Status display (TV, DVD)
MENU: confirm the menu selection
Green button: ShowView menu
Red button: new chapter marker
PLAY: press short: Start of current chapter/previous chapter;
press long: search back; PAUSE: press short: slow motion back
Record
Pause /single frame
Switch on/off - on stand by
TV Radio Digital
Switch over to operate DVD-Player
TV Sound menu
STOP: Select station directly
MENU: enter numbers or letters
MENU: enter numbers or letters
ViewVision DR+: STOPP: Call AV selection
Card Reader operation
ViewVision DR+: „Home“ menu
PIP (picture in picture)
Info; PLAY: menu bar
MENU: hide menu
P+/P– PLAY: Next chapter; STOP: Select station up/down
MENU: select/set
Yellow button: Zoom
Blue button: DISC: short: Set marker; long: Marker search
Playback
PLAY: Press short: next chapter; Press long: search forward
PAUSE: Press short: slow motion forward
Stop
63 -
Operating additional equipment
Rotating the TV set
Your TV set has a connection for a rotating stand control. If the set is
mounted on a motorised Loewe stand, you can use the remote control
to adjust it to your seating location accordingly.
Call TV menu.
➠ A motor unit is connected.
➠ In normal TV mode, without other displays.
34Select Settings,
6go to the menu line below.
34Rotate the TV set.
Do not place any objects in the rotation range of the TV set that could
obstruct the rotation or that could be knocked over by the rotation
movement.
Setting the range of rotation
You can specify the rotation range of the TV device (maximum +/- 40
degrees) by setting the maximum right and left stop position.
34Select Settings,
6go to the menu line below.
34Select Miscellaneous,
6go to the menu line below.
INFO
END
Activating the switch-off position
END
4Basic adjustment (right)
Turn your TV set as far to the right as the installation
position of your set allows. This will be the maximum
right rotation position in future.
OK confirms basic adjustment to right.
END
3
Basic adjustment (left)
Turn your TV set as far to the left as the installation
position of your set allows. This will be the
maximum left rotation position in future.
OK ends the basic adjustment.
- 64
34Select Set switch-off position,
OK calls Set switch-off position.
Close the menu.
34Select Basic adjustment,
OK calls the basic adjustment.
Close the menu.
34Select Rotate TV,
6go to the menu line below.
34Set desired switch-off position.
The TV set rotates in the process.
OK Save the set position as the switch-off position.
34Select Rotate TV,
6go to the menu line below.
Rotate TV
Basic adjustment (left)
-30
OK End of basic adjustment
34Select Miscellaneous,
6go to the menu line below.
TV menu
Settings
Miscellaneous
Rotate TV
Set switch-off position
0
OK Adopt
Call TV menu.
Rotate TV
Basic adjustment (right)
21
OK Proceed
Specifying the switch off position
This is where you specify the position that the TV will take when it is
switched off. In order for the TV set to return to the determined switch-off
position when switching it off, this must be activated (see below).
Call TV menu.
34Select Settings,
6go to the menu line below.
34Select Miscellaneous,
6go to the menu line below.
34Select Rotate TV,
6go to the menu line below.
34Select Activate switch-off position,
6go to the menu line below.
34Select yes.
Close the menu.
If the TV set is switched off with the on/off key on the remote control or
with the switch integrated in the display then it will turn to the defined
switch-off position. When it is switched back on, it returns to the position
last set.
Troubleshooting
Problem
Possible cause
Remedy
All menus are displayed in the wrong language. The menu language was set incorrectly.
Set the menu language:
Press the INFO button in TV mode (Index).
Mark the first key word and call it with OK.
Then select the language and confirm it with
OK.
In the TV menu, Connections cannot be called
(displayed in grey).
A timer recording is in progress.
Wait until the timer recording ends or delete
the timer recording (page 55).
The control functions of the Loewe Recorder
and the Timer are not working or are not
working properly
a)The Digital Link function is not activated or
not possible in the recorder.
b)EURO-AV cable is not connected.
c)Recorder is not logged in.
a)Activate Digital Link in the recorder (see
operating instructions of the recorder).
b)Connect EURO-AV cable (page 43).
c)Register recorder (page 40).
General problems when connecting external
devices via an AV input.
a) The device is not logged in to the connection a) In the connection wizard (TV menu →
wizard or is connected differently from shown
Connections → New devices/modifications)
in the connection diagram.
compare the connection diagram with the
actual installation and connect as shown if
necessary (page 40).
b)The AV standard is set incorrectly.
b)Set the correct standard (page 17).
c)The signal type is set incorrectly.
c)Set the correct signal type (page 41).
If AV standard or AV signal is set to "Automatic"
then this can cause errors to be detected with
signals that do not comply with standards.
In this case standard and signal must be set
according to the information in the operating
manual of the external device.
The connection of a decoder does not function a)The signal is not decoded because the
or does not function properly.
correct decoder stations have not been
selected in the connection wizard.
b)In decoder mode the sound is missing
because the wrong decoder sound has been
assigned in the connection wizard.
a)Follow the instructions in the connection
wizard (TV menu → Connections → New
devices/modifications) and select the
appropriate decoder station (page 40).
b)Follow the instructions in the connection
wizard and select the right audio source
(Decoder, TV oder Autom.) (page 40), see
also the decoder manual.
65 -
Troubleshooting
Problem
Possible cause
Remedy
Digital Link Plus does not work.
a)EURO-AV cable is not fully wired (pin 10 not
wired).
b)Some recorders can only adopt stations
during the initial installation of the TV set.
a)Replace the EURO-AV cable.
With Teletext various character sets are
displayed incorrectly.
The wrong character set has been set in the
Teletext menu.
Set the right character set: Select Teletext
menu → Settings → Character set → Standard
or the appropriate character set.
No sound via the external digital audio
amplifier.
a)The external digital audio amplifier does not
support the selected sound format (Dolby
Digital, dts, MPEG).
a)Set PCM stereo on the DVD player in the
sound selection. For DVB stations on the TV
set switch to stereo in the status display (END)
– language/sound selection (green button).
b)Connect AUDIO DIGITAL OUT from the TV set
to a digital input of the external digital audio
amplifier and select the appropriate input to
this.
b)TV set and external digital audio amplifier are
not connected with each other.
b)Restore the recorder to the as-delivered
state (see recorder's operating manual).
The picture of a connected external recorder
is visible but the timer cannot be called.
The device is not registered in the connection
wizard or is connected differently from shown
in the connection diagram.
In the connection wizard (TV menu → Connections
→ New devices/modifications) compare the connection diagram with the actual installation and
connect as illustrated (page 40).
The picture of a connected external recorder
is visible but the error message no recorder
available is still output.
The device is not registered in the connection
wizard or is connected differently from shown
in the connection diagram.
In the connection wizard (TV menu → Connections
→ New devices/ modifications) compare the
connection diagram with the actual installation
and connect as illustrated (page 40).
Photos on the USB stick are not displayed
correctly in the PhotoViewer or a "?" appears.
The photo is not available in a displayable
format.
Convert photo file into a standard JPG format
on the PC.
- 66
Technical data
General data
Type
Article number
Device dimensions without base (W x H x D) in cm
Weight (approximate) in kg
Display
Picture diagonal in cm/picture format
Resolution in pixels
Dynamic contrast ratio
Static contrast ratio
Viewing angle horizontal and vertical
Power consumption (EN 62087)
in operation (watt)
in standby (watt)
Ambient temperature (Celsius)
Relative humidity (non-condensing)
Air pressure
Individual 40 Compose Full-HD+ 100
67437xxx
101.4 x 61.7 x 10.3
31.5
FHD-LCD technology
101 / 16:9
1920 x 1080
10,000:1
2,000:1
178°
Individual 46 Compose Full-HD+ 100
67439xxx
114.1 x 69.2 x 11.4
35.7
FHD-LCD technology
117 / 16:9
1920 x 1080
10,000:1
2,000:1
178°
Individual 52 Compose Full-HD+ 100
67440xxx
130.8 x 78.5 x 12.8
52.0
FHD-LCD technology
132 / 16:9
1920 x 1080
10,000:1
2,000:1
178°
145
1,2
165
1,8
180
1,8
5° – 35°
20 – 80%
800 – 1114 hPa (0 – 2000 m above sea level)
Electrical data
Chassis designation:............................................................................................ L 2710
Power supply:.........................................................................220 V – 240 V/50–60 Hz
Tuner:................................................................................... VHF/UHF/cable/hyperband
Range:.......................................................................................... 45 MHz to 860 MHz
Station storage locations incl. AV and radio:.......................................................... 4000
TV standards:................................................................................... B/G, I, L, D/K, M, N
Colour standard:........................................ SECAM, PAL, NTSC, NTSC-V, PAL-V (60 Hz)
Sound standard......................................................Mono/Stereo/2-Ton/Nicam B/G, I, L
......................................................Dolby Digital, Dolby Virtual Speaker, DTS
Audio nominal power (sine):........................................................................ 2 x 20 watt
Teletext:........................................................................................... TOP/FLOF Level 2.5
Page memory......................................................................................................... 2000
Digital teletext (only in UK / IRL with active MHEG-5 software)........................MHEG-5
Connections (max. equipment)
Mains socket: ..................................................................................... Supply voltage
EURO-AV 1 Video IN:.....................................................................Y/C (S-VHS/Hi 8)
..................................................................CVBS (VHS/8 mm)
Video OUT:..............................................................CVBS (VHS/8 mm)
.................................................................Y/C (S-VHS/Hi 8)
Audio IN:.........................................................................................L/R
Audio OUT:......................................................................................L/R
EURO-AV 2 Video IN:.....................................................................Y/C (S-VHS/Hi 8)
..................................................................CVBS (VHS/8 mm)
........................................................................................RGB
Video OUT:..............................................................CVBS (VHS/8 mm)
.......................................... Y/C, (only with SVHS Link Plus)
Audio IN:.........................................................................................L/R
Audio OUT:......................................................................................L/R
Jack 3.5 mm:
Mini-DIN (AVS)
Cinch (yellow)
Cinch (white/red)
2x IEC socket 2x F socket 2 x screw terminals 2 x screw terminals Jack 3.5 mm
Cinch
2 x Cinch 2 x Cinch Cinch
Cinch
Cinch
Cinch Cinch SUB-D
SUB-D
SUB-D
Mini-DIN Mini-DIN 2 x USB
2 x HDMI 2 x CI-Slot ..........................................................Headphones 32- 2000 ohm
Video IN:..............................................................Y/C (S-VHS/Hi 8)
.............................................................CVBS (VHS/8 mm)
Video IN:...........................................................CVBS (VHS/8 mm)
Audio IN:.............................................................L (white) / R (red)
75 Ohm/5 V/80 mA:................................. Antenna/cable/DVB-T/C
75 Ohm 13/18 V/350 mA:...............................ANT-SAT DVB-S/S2
Speaker Right:......................................................+ (red) / - (black)
Speaker Left:.........................................................+ (red) / - (black)
AUDIO IN2:...............................................................................L/R
AUDIO IN max. 2Vrms:.......................................................Centre
AUDIO IN1:.........................................................L (white) / R (red)
AUDIO OUT (level depends on configuration):....L (white) / R (red)
COMPONENT IN:........................................................Cb/Pb signal
COMPONENT IN:..........................................................Cr/Pr signal
COMPONENT IN:............................................................... Y signal
AUDIO DIGITAL IN (SPDIF):.........................................Digital audio
AUDIO DIGITAL OUT (SPDIF):.....................................Digital audio
AUDIO LINK:............................................................... Multi-sound
PC IN:..............................................................PC/STB video signal
RS-232C:.................................................................serial interface
SERVICE:................................................................... Service/L-Link
CONTROL:.................................................. Rotating stand control
USB 2.0:................................................... Standard JPEG/MP3 files
Digital Video/Audio IN
Type A 19pole Standard 1.3:.....................Digital video and audio
Common Interface.......................................... Slot for CA module
67 -
Accessories
Accessories
Trim:
With your Individual Compose device it is possible to replace the laterally
attached trim (panels) to match the ambiance of your home. There are
different surface structures or colours that can be selected for your device.
Please contact your dealer in this regard.
Wood trim is a natural product. In this case UV light (strong sunlight) can
cause slight discoloration.
Stereospeaker I Compose (2 pieces):
Add two stereo speakers to your Individual Compose which can be fixed
directly to the TV set (not possible in Individual 52 Compose) or mounted
separately on the wall.
Cube i Rack:
The Cube i Rack is designed as a supplemental rack that can accommodate two peripheral devices such as DVD player and/or DVD recorder, as
well as the subwoofer of the Loewe Individual Sound speaker system. If
a subwoofer is not used then the Cube i Rack can accommodate up to
four peripheral devices.
Adapter and cables:
AUDIO LINK adapter AUDIO LINK AUDIO LINK AUDIO LINK Cubic plug cable Centerspeaker I Compose:
An external centre speaker is recommended for perfect spatial sound. It
can be installed on a table stand or mounted on the wall. A visually attractive solution is the Center Floor Stand I Compose in which the loudspeaker
is already integrated in the installation solution. The Centerspeaker I
Compose can be combined with the Loewe Individual Sound System.
Loewe Individual Sound:
Your TV set can be perfectly supplemented with the Individual Sound
speaker system. Numerous speaker combination possibilities with standing
speakers, satellite speakers and a subwoofer can be implemented. Here
as well it is possible to choose the colours of housing and trim.
Loewe Individual Sound Projector:
With the Loewe Individual Sound Projector you can easily enjoy digital
Surround Sound without expensive installation and connection of several
speakers. The Sound Projector is easy to set and operate.
Loewe DVD recorder:
The DVD recorders from Loewe are characterised by form and colour,
which match Loewe TV sets, adapted user guidance and technology.
Combined these devices form a system that offers many advantages.
Loewe Blu-ray Player:
With the Loewe Blu-ray Player “BluTech Vision“ you are ideally equipped
for the successor format to DVD. With the Loewe system integration
you control BluTech Vision and your Loewe TV set simultaneously with
the Assist remote control.
Subject to availability.
- 68
1.5 m
1.5 m
6 m
10 m
1.5 m
Loewe order no. 89954.001
Loewe order no. 89952.001
Loewe order no. 89952.002
Loewe order no. 89952.003
Loewe order no. 90418.930
Accessories
Setup possibilities
Individual 52 Compose Full-HD+ 100
Wall Mount
Screen Wall Mount 2 (1
•
•
•
•
•
Table Stand I 52 Compose
Table Stand I 40-46
Compose
Individual 46 Compose Full-HD+ 100
•
•
•
•
•
•
•
Floor Stand 5 MU SP
Center Floor Stand
I Compose
Screen Floor Stand I 52 MU
Screen Floor Stand MU
Wall Mount (delivery status)
Table Stand I 52 Compose
Floor Stand 5 MU SP (2
Center Floor Stand I Compose
Screen Floor Stand I 52 MU
Wall Mount (delivery status)
Screen Wall Mount 2 (1
Table Stand I 40-46 Compose
Floor Stand 5 MU SP (2
Center Floor Stand I Compose
Screen Floor Stand MU
Screen Lift Plus (1
Individual 40 Compose Full-HD+ 100
•
•
•
•
•
•
•
Wall Mount (delivery status)
Screen Wall Mount 2 (1
Table Stand I 40-46 Compose
Floor Stand 5 MU SP (2
Center Floor Stand I Compose
Screen Floor Stand MU
Screen Lift Plus (1
Only in conjunction with appropriate adapters that are sold separately.

(1
Th
ec
o
co de
de nu
an mb
d er
Ple thu 300
as s th 1
sa e k e p can
fe ee a ce
pla p i ren ls
ce n a tal an
.
loc acc
k. es
s
Screen Lift Plus (1
69 -
Glossary
0-9
24p movie display: Modern movie makers produce movies with 24 (full)
pictures per second (24p), conventional TV sets (and most DVDs) show
50 (half) pictures per second. To play the movie, the original number
of pictures is doubled and the film sped up. This is optimal for sports
broadcasts but for quieter movies it distorts the picture quality.
A
Active antenna: An antenna with its own power supply or amplification
that can improve reception in areas with poor reception.
AV socket: Socket for audio and video signals.
AV sources: Audio/video source.
AVS: Audio/video sockets on the TV set (cinch and Mini-DIN).
B
Band: Designation for a frequency range.
C
CA module: The Conditional Access module contains the coding system
and compares the transmitted code with the one on the Smart Card. If
they match, the appropriate stations or programmes are decoded.
Cinch cable: Cable for transmitting audio or video.
CI slot: See Common Interface.
Common Interface: The Common Interface (CI slot) is a standardised
interface. By inserting suitable decoding modules (CA modules) and a
Smart Card coded digital programmes can be used.
Component IN: Connection by which the video signal is transmitted via
three separate cinch connections. It is made up of the brightness signal
"Y" and the colour difference signals "Pb" and "Pr". YPbPr is the original
analogue version of the digital YCbCr with which, among other things,
video data stored on the DVD and transmitted by satellite, cable or antenna
in DVB are colour coded.
Conditional Access module: See CA module.
D
Decoder: Analogue, coded TV signals are passed through a decoder and
made visible again.
Digital Link: System for controlling recorders (for video and DVD recorders
from Loewe) via the Euro AV sockets of the Loewe TV set with concealed
setup. Controlling the recorder for timer recordings.
Digital Link HD: System for controlling devices via the HDMI connection
of the Loewe TV set in the case of concealed installation.
Digital Link Plus: System for controlling recorders according to protocol
50. For analogue stations the station and timer data are transmitted via
the EURO-AV socket to the recorder. The timer recording is executed
exclusively by the recorder. There is a different designation with different
manufacturers.
- 70
Dolby Digital: Digital multi-channel audio. The digital standard for high
quality home movie systems. The individual channels are broadcast separately in this standard. The three front channels right, left and centre, the
two surround channels right and left and the external subwoofer channels
are called a 5.1 signal. Another term for Dolby Digital is AC3.
Dolby Pro Logic: Analogue multi-channel audio. Converts a Dolby-coded
stereo signal into a surround sound. This usually contains four channels
(front left, centre, front right, surround channel). A special subwoofer
channel is not generated in this method.
Dolby Pro Logic II: Analog multi-channel audio. Dolby Pro Logic II is a further development of Dolby Pro Logic. This method generates a 6-channel
spatial sound from a stereo or Pro-Logic signal (front left, centre, front
right, surround left, surround right, subwoofer).
Dolby Surround: Analogue multi-channel audio system that brings four audio channels down to two audio tracks with the aid of a matrix coding.
Dolby Virtual Speaker: The Dolby Virtual Speaker technology simulates
the surround playback of a real 5.1-channel playback with only two
speakers.
DTS: Digital Theater Systems; Digital multi-channel audio.
DVB-C/-S/-T: Digital Video Broadcasting stands for digital television.
Technical DVB is the standardised process for transmitting digital content
(television, radio, multi-channel audio, room sound, EPG, Teletext, and
other supplemental services) through digital technology. C stands for
transmission via cable, S for distribution via satellite and T for terrestrial
or antenna distribution.
DVD: Abbreviation of Digital Video Disk and later Digital Versatile Disk.
DVD preceiver: Combi-device of DVD player and radio without integrated
amplifier.
DVI: Digital Visual Interface, is an interface for transmitting digital video
and graphic data (without audio).
Dynamic contrast ratio: Here the light intensity of the display is adapted
in case of a high black portion in the picture. The so-called backlights
are dimmed automatically and the contrast ratio increases temporarily,
i.e. dynamically.
E
Electronic Programme Guide: See EPG.
EPG: Electronic Programme Guide is the electronic variant of a printed
television programme guide. Using the EPG you can watch the TV
programme of the TV stations which transfer the appropriate data. The
overview of the programmes contains the title, beginning and end and
the duration of the programme. In addition also a brief description of
respective content of the programme is displayed.
Euro AV socket: Interface for connecting video devices to a TV set. This
socket is also referred to as Scart socket.
Glossary
F
FLOF: Full Level One Facilities. Teletext system in which designations and
numbers of the jump destinations are transmitted separately for every
page on the bottom line. This guides the reader to related topics for
example. An information about which pages exist and which pages have
sub-pages is not available in FLOF.
H
HDCP: High-bandwidth Digital Content Protection. Coding system
provided for the interfaces DVI and HDMI for protected transmission of
audio and video data.
HDMI: High Definition Multimedia Interface is a newly developed interface
for full digital transmission of audio and video data.
HDTV: High Definition Television is an umbrella term that covers a number
of high resolution television standards.
HD-Ready: A quality seal that is awarded to products which are capable
of displaying high-definition television (HDTV).
High band and Low band: Transmission ranges for satellites.
I
ID3 tags: Additional information for MP3 and WMA audio files. Information about the singer, title, album and album cover can be saved here
among other things. These data are edited on the PC by an ID3 tag
editor.
J
JPEG/JPG: Joint Photographic Experts Group is a committee that has
developed a standard method of compression for digital images. This
JPEG method (JPG for short) named after the committee is a widely used
graphic format for photos.
L
LCD: Liquid Crystal Display.
LCN: Logical Channel Numbers. In stations with LCN, the channel location
number belonging to the station is also transmitted by the provider. The
stations are sorted according to these channel location numbers.
L-Link: Intelligent system connection between Loewe devices for the
automatic exchange of information. Makes the operation of TV and
Loewe system components even more convenient.
LNB/LNC: The crucial electronic component of a satellite antenna is
referred to as an LNB (Low Noise Block Converter). It is mounted in the
focal point of a parabolic antenna. The designation LNC (Low Noise
Converter) indicates that conversion to lower intermediate frequency
takes place. The supplemental block in the LNB refers to the fact that a
whole frequency range (a block) is converted in each case.
M
MHEG-5: Digital teletext standard of the Multimedia and Hypermedia
Expert Group. At the moment only available in United Kingdom and
Ireland.
Modulator: Transmitter in the video or DVD recorder so that the devices
can receive signals via the tuner of the TV device.
Mono: Single-channel audio.
MPEG: Digital compression process for video.
MP3: Data format for compressed audio files.
N
Network ID: NID refers to the so-called programme ID number also known
as network ID – a number between 0 and 8191. This specification is
necessary in specific cable networks of some countries. Then only DVB
signals of this station network are searched for.
NICAM: Audio standard. Is used in Denmark, England, France, Sweden,
and Spain.
NTSC: American picture standard.
P
Page Catching: For Teletext, refers to going to and calling a page
number.
PAL: European picture standard.
PCM: Pulse Code Modulation for digital audio.
Picture in Picture: See PIP.
PIP: Picture in Picture; a function which displays two pictures on the
screen.
Pixel: Refers to the smallest unit of a digital grid graphic and its representation on a screen with grid control.
Pixel error: A pixel error is a defective pixel, usually on an LCD. Pixel errors
may be caused by production faults. They are expressed for example by
a constantly lit pixel or a constantly black pixel. Single defective pixels
however are excluded from a guarantee.
Progressive JPEG: Progressive JPEGs are built up gradually. The picture
quality improves continuously during loading.
ProScan/Progressive Scan: Progressive Scan (abbr. PS) or full picture
method is a technique in the picture build-up of monitors, TV sets,
beamers, and other display devices in which the output device is not
sent line interlaced half pictures – unlike in the interlace technique – but
real full pictures.
R
RGB: Colour signals red, green and blue.
71 -
Glossary
S
Satellite tuner: Receiver for satellite programmes.
SDTV: Standard Definition TeleVision.
SECAM: French picture standard.
Set-Top-Box: Set-Top-Box (STB for short) refers to a device in entertainment electronics which is connected to another device, usually a TV set,
and offers the user additional functional options.
Signal input groups: Depending on the applied signal, the signal sources
are divided into different groups. All signal input groups with their corresponding signal types are the possible inputs are listed below.
TV analogue:
Signal type: FBAS, YC, RGB-SD (480i/576i), Component-SD (480i/576i)
Input:
Tuner analogue, AV1, AV2, AVS, COMP. In
TV digital:
Signal type: DVB-SD, HDMI-SD (480i/576i)
Input:
Tuner digital, HDMI1/DVI, HDMI2/DVI
HD analogue:
Signal type: RGB-HD (video mode: e.g.1920x1080, 1280x720),
Component-HD (video modes: e.g. 1920x1080, 1280x720)
Input:
COMP. IN, PC IN
HD digital:
Signal type: DVB-HD, HDMI-HD
Input:
Tuner digital, HDMI1/DVI, HDMI2/DVI
PC:
Signal type: RGB
(PC modes: e.g. 800x600, 1024x768, 1280x1024, 1360x768)
Input:
PC IN
PhotoViewer:
Input:
USB
Signal strength: strength of the received antenna signal.
Signal quality: quality of the incoming antenna signal.
Smart Card: The Smart Card is an electronic chip card issued by the respective programme provider or by the certification-free Pay TV operators. It
contains the code which is decoded by the CA module.
Static contrast ratio: Describes the difference between the brightest and
darkest picture display.
Stereo: Dual-channel audio.
Switching voltage: Video devices specify this voltage to switch the TV
device to playback.
Symbol rate: describes the transmission speed for data transmission.
- 72
T
Terrestrial: In data transmission a wireless transmission that does not use
satellites as intermediate station is referred to as terrestrial.
TFT: Thin-Film-Transistor. One widely distributed application is control of
liquid crystal flat screens, for which a signal transistor is used for each
pixel. This design of display is also referred to as active matrix, however
it is frequently also referred to as TFT display.
TOP: Table of Pages. Teletext system in which the individual pages are
divided into topics. The blocks stand for a higher hierarchy level (e.g.
News, Sport, Programmes) and the groups for the level below (e.g. Home/
Abroad, Football/Tennis). Abbreviations can be assigned to the pages
which are displayed in colour on the bottom line and can be selected
with the four coloured buttons on the remote control. Information is also
transmitted which pages exist and which have sub-pages.
Tuner: Another term for receiver.
U
USB: Universal Serial Bus. Serial bus system for connecting external devices
(USB card reader, USB stick).
V
VGA: PC interface for connecting a monitor.
Virtual Dolby Surround: A technology certified by Dolby. It creates a virtual
sound from two speakers. Prerequisite is Dolby Surround or Dolby ProLogic
as a source. The used virtualizer processes all multi-channel signals and
gives the impression of additional speakers.
VPS: The Video Programming System (VPS) is a signal that some (not all)
television transmitters transmit in the vertical blanking interval of the
television signal. The signal is used by video and DVD recorders when recording programmes to react to delays in start time, programme changes
and excesses of the planned program time.
Y
Ycc/Ypp: Colour standards for Set-Top-Boxes.
YCbCr: Digital colour model, see COMPONENT IN.
YPbPr: Analogue colour model, see COMPONENT IN.
Index
0-9
24p format 44
A
Access code 38
Active speakers 49
Adjusting the picture 21
Adjusting the sound 20
Alarm 38
Assist+ 8, 16
Audio amplifiers 52
Auro Loewe Preceiver 47
Auto format 21
Automatic dimmer 21
AV audio signal 20
AV selection 19
Display 12
DVB character set 23
DVB software 36
DVD button 62
DVI 44
Muting 20
E
Encrypted stations 13, 24, 35
EPG 30
O
On-screen displays 39
Overview diagram 17
F
Factory settings picture/sound 21
Favorites 19
File folder 57
First installation wizard 12
FLOF 32
P
Page selection 32
Parental lock 38
PC IN 45
Personal text pages 22, 33
PhotoViewer 56
Picture 21
Picture adjustment 21
Picture format 21, 22
16:9 22
4:3 22
Cinema 22
PALplus 22
Panorama 22
Zoom 22
Picture in Picture 28
PIN 38
PIP 28
Programme info 22
B
Balance 20
Batteries 11
Brightness 21
Button functions 22
H
HDMI 44
Headphone volume 20
Help 15
HiFi/AV amplifier 52
C
CA module 35
Card reader 56
Change favourites lists 27
Add station 27
Delete station 27
Move station 27
Rename list 27
Change station 26
Delete station 26
Move station 26
Rename station 26
Restore station 26
CI slot 35
Code number 38
Coloured buttons 22, 23, 32
Component IN 46
Connecting the antenna 11
Connections 5, 6
Connection wizard 40
Contrast 21
Control unit 4
Copy protection 55
I
Index in the TV set 16
Individual Sound 48
Info Display 15
iPIP 28
D
Data capture 31
Digital audio input 53
Digital Link 55
Digital Link HD 44
Digital Link Plus 54, 55
Digital teletext 33
L
Language 12, 16, 17, 65
Language/audio selection 23
Last station 22
LNC/LNB 13
Loudness 20
M
Mains switch 12
Manual station search 25
Manual timer 55
Maximum volume 20
Memorise 30
Menu operation 15
Mobile phone keypad 15
Move picture vertically 22
MusicBox 58
All albums 59
All titles 59
Artists 59
Browse/sort 59
Files 59
Playlist 60
Repeat 61
Select/play music 58
N
New devices/modifications 40
Numeric buttons 15, 16, 18
R
RADIO button 12, 62
Radio menu 17, 34
Radio mode 12, 34
REC button 62
Recording 54
Recording wizard 54
Remote control 3, 11, 62
Repeat initial installation 12
Reset picture/sound 21
Rotating the TV set 64
RS-232C interface 53
S
Safety 9, 10
Satellite system 13
Scope of delivery 7
Search wizard 24
Select station 18
Service 74
Settings 17
Signal type 41
Slide show 57
Small PIP 28, 29
Smart Card 35
Software update 36
Sound 20
Sound components wizard 47
Sound mode 20
Sound off 20
Split screen 28, 29
Standard PIP 28
Standby mode 12
Station list 18
Station search/update 24
Status display 23
Storage medium 57
Subtitles 23
Switching off 12
Switching on 12
Switching voltage 17
Switch on volume 20
T
Teletext 32
Teletext functions 22
Teletext subtitles 22
Time 22
Time and date 39
Timer data 54
Date 54
Recorder 54
Recording time 54
Recording type 54
VPS 54
Timer functions 38
Timer list 55
Timer recordings 54
TOP 32
TOP table 32
TV base software 36
TV button 11, 62
TV menu 17
TV set equipment 7
TV speakers 11, 47
U
USB stick 36, 56, 58
V
Video source 19
Videotext subtitles 33
Volume 20
Volume adjustment 20
VPS times 33
73 - Service
Loewe Austria GmbH
Parkring 12
1010 Wien, Österreich
Tel +43 - 1 22 88 633 - 0
Fax +43 - 1 22 88 633 - 90
Email [email protected]
Loewe Opta GmbH,
Customer Care Center
Industriestraße 11
96317 Kronach, Deutschland
Tel +49 1801–22256393
Fax +49 9261–99500
Email [email protected]
ISSAGOGIKI EMBORIKI ELLADOS
S.A.
321 Mesogion Av.
152 31 Chalandri-Athens, Hellas
Tel +30 - 210 672 12 00
Fax +30 - 210 674 02 04
Email [email protected]
International Dynamics
Australasia Pty Ltd.
129 Palmer Street
Richmond 3121, Victoria, Australia
Tel +61 - 3 - 94 29 08 22
Fax +61 - 3 - 94 29 08 33
Email mail@international
dynamics.com.au
Kjaerulff 1 A/S
C.F. Tietgens Boulevard 19
5220 Odense SØ, Denmark
Tel +45 - 66 13 54 80
Fax +45 - 66 13 54 10
Email [email protected]
Basys Magyarorszagi KFT
Tó park u.9.
2045 Törökbálint, Magyar
Tel +36 - 2341 56 37 (121)
Fax +36 - 23 41 51 82
Email [email protected]
Gaplasa S.A.
Conde de Torroja, 25
28022 Madrid, España
Tel +34 - 917 48 29 60
Fax +34 - 913 29 16 75
Email [email protected]
Plug&Play
Bednjanska 8, 10000 Zagreb
Hrvatska (Kroatia)
Tel +385 1 4929 683
Fax +385 1 4929 682
Email [email protected]
TEDRA TRADING OY
Kuusemetsa 3
Saue 76506, Estonia
Tel +372 - 50 14 817
Fax +372 - 67 09 611
Email [email protected]
Loewe Italiana SRL
Largo del Perlar, 12
37135 Verona (VR), Italia
Tel +39 - 045 82 51 611
Fax +39 - 045 82 51 622
Email Stefano.Borgognoni@
loewe.it
Loewe Opta Benelux NV/SA
Uilenbaan 84
2160 Antwerpen, België
Tel +32 - 3 - 2 70 99 30
Fax +32 - 3 - 2 71 01 08
Email [email protected]
Darlington Service
Kn. Klementina Street, bl. 193
1618 Sofia, Bulgaria
Tel +359 - 2 955 63 99
Fax +359 - 2 955 63 99
Email [email protected]
A Cappella
Ausros Vartu 5, Pasazo skg.
01129 Vilnius, Lithuania
Tel +370 - 52 12 22 96
Fax +370 - 52 62 66 81
Email [email protected]
Avitech Co. SRL
1/II Pipera Tunari St.
007190 Voluntari, Ilfov, Romania
Tel +40 - 21 200 64 64
Fax +40 - 21 200 64 65
Email [email protected]
DONEO CO. LTD
34/36 Danny Cremona Street
Hamrun, HMR02, Malta
Tel +356 - 21 - 22 53 81
Fax +356 - 21 - 23 07 35
Email [email protected]
Service Center Loewe
ul. Verkhnaya Maslovka, d. 29
125083 Moscow, Россия
Tel +7 - 495 612 50 43
Fax +7 - 495 612 47 10
Email [email protected]
SOMARA S.A.
377, Rue Mustapha El Maani
20000 Casablanca, Morocco
Tel +212 - 22 22 03 08
Fax +212 - 22 26 00 06
Email [email protected]
Kjaerulff 1 AB
Ridbanegatan 4, Box 9076
200 39 Malmø, Sverige
Tel +46 - 4 06 79 74 00
Fax +46 - 4 06 79 74 01
Email [email protected]
CableCom AS
Ostre Kullerod 5
3241 Sandefjord, Norge
Tel +47 - 33 48 33 48
Fax +47 - 33 44 60 44
Email [email protected]
BaSys Czech & Slovak s.r.o.
Stará Vajnorská 17/A
831 04 Bratislava, Slovakia
Tel + 421 2 49 10 66 18
Fax + 421 2 49 10 66 33
Email [email protected]
ENKAY ELEKTRONIK SAN. Ve Tic.
Ltd. Sti.
Alemdag Cad: Site Yolu No.: 10
81230 Ümraniye/ Istanbul, Türkiye
Tel +90 - 216 634 44 44
Fax +90 - 216 634 39 88
Email [email protected]
Telion AG
Rütistrasse 26
8952 Schlieren, Schweiz
Tel +41 - 44 732 15 11
Fax +41 - 44 732 15 02
Email [email protected]
Loewe Opta France S.A.
13 rue du Dépôt,
Parc del l‘Europe, BP 10010
67014 Strasbourg Cédex, France
Tel +33 - 3- 88 79 72 50
Fax +33 - 3- 88 79 72 59
Email [email protected]
PL Trading (pz 2004) Ltd.
27, Aliat Hanoar St.
Givataiim 53401, Israel
Tel +972 - 3 - 57 27 155
Fax +972 - 3 - 57 27 150
Email [email protected]
International Dynamics (NZ) Pty
Ltd
PO Box 109 317, Newmarket
Auckland, New Zealand
Tel +64 9 379 0179
Fax +64 9 379 0279
Email enquiries@international
dynamics.co.nz
HADJIKYRIAKOS & SONS LTD.
121 Prodromos Str., P.O Box 21587
1511 Nicosia, Cyprus
Tel +357 - 22 87 21 11
Fax +357 - 22 66 33 91
Email [email protected]
Kjaerulff 1 OY
Uudenmaantie 100
20760 Piispanristi, Finland
Tel +358 - 20 751 3800
Fax +358 - 20 751 3801
Email [email protected]
Origo Ltd
Unit 23 Magna Drive
Magna Business Park, City West
Dublin 24, Republic of Ireland
Tel +353-1-4666700
Fax +353-1-4666706
Email [email protected]
Mayro Magnetics Portugal, Lda.
Rua Professor Henrique de Barros
Edifício Sagres, 2º. C
2685-338 Prior Velho, Portugal
Tel +351 - 21 942 78 30
Fax +351 - 21 942 78 30
Email [email protected]
K+B PROGRES A.S.
U Expertu 91
25069 Klicany u Prahy, Česko
Tel +420 2 72 12 21 11 (222)
Fax +420 2 72 12 22 39
Email [email protected]
Loewe UK Limited
Century Court, Riverside Way
Riverside Business Park, Irvine,
Ayrshire
KA11 5DD, UK
Tel +44 - 1294 315 000
Fax +44 - 1294 315 001
Email [email protected]
SAS
Hamad Al Haqueel Street,
Rawdah, Jeddah
Kingdom of Saudi Arabia
Tel +966 (2) 665 4616 ext: 666
Fax +966 (2) 660 7864
Email [email protected]
DSV TRADING SA
Plac Kaszubski 8
81-350 Gdynia, Polska
Tel +48 - 58 - 6 61 28 00
Fax +48 - 58 - 6 61 44 70
Email [email protected]
Dubai Audio Center
P.O. Box 32836, Sheik Zayed Road
Dubai, UAE
Tel +971 - 4 343 14 41
Fax +971 - 4 343 77 48
Email [email protected]
THE SOUNDLAB (PTY) LTD
P.O. Box 31952, Kyalami 1684
Republic of South Africa
Tel +27 - 1 14 66 47 00
Fax +27 - 1 14 66 42 85
Email [email protected]
© by Loewe Opta 290508
74