Lumiscope 1131 User's Manual

A U T O M A T I C
U P P E R
A R M
Blood Pressure Monitor
Model 1131
Features:
• Dual Person Memory Zones
• 50 Memories for each zone
• Average for Last 3 Memories
• Date and Time Stamp
• One Touch Operation
Table of Contents:
Introduction .................................. 2
Name/Function of Each Parts ........ 2
Quick Read Measuring Technology .. 3
Preliminary Remarks ...................... 3
About Blood Pressure ..................... 3
Blood Pressure Standard ................ 4
Blood Pressure Fluctuation ............. 4
Display Explanation ........................ 5
Installing Battery ............................ 6
Applying the Cuff ............................ 7
Measurement Procedures ............ 8,9
Recalling Values from Memory ...... 10
Clearing Values from Memory ....... 11
Time Adjustment .......................... 12
Helpful Tips .................................. 13
Troubleshooting ............................ 14
Cautionary Notes .......................... 15
Specifications .............................. 16
Introduction
Blood pressure measurements determined with Lumiscope Model 1131 are equivalent to those
obtained by a trained observer using cuff/stethoscope auscultation method, within the limits
prescribed by the American National Standard, Electronic or Automated Sphygmomanometers.
This monitor is to be used by adult consumers in a home environment.
Lumiscope Model 1131 is protected against manufacturing defects by an established
International Warranty Program. For warranty information see page 16 or contact the Lumiscope
Repair Department at 1-800-672-8293.
Attention: Consult the accompanying documents before use.
• Please read this manual carefully before use, for specific information on your own blood
pressure, contact your physician. Please be sure to keep this manual.
Name/Function of Each Part:
User-Switching Key
LCD Display
Date/Time Set Key
Memory Recall button
Arm Cuff
Battery Compartment
ON/OFF/START button
Air Tube and Connector
4 x ‘AA’ size, 1.5V
Batteries
2
Quick Read Measuring Technology
This monitor uses trend-setting Quick Read Technology to detect your blood pressure. With one
touch of a button, the device will automatically start to inflate and determine your blood pressure
by analysis of your pressure oscillations. When the measurement is completed, the device
will exhaust cuff pressure and display your systolic, diastolic, and pulse. Measurement time is
significantly shortened, and user comfort is greatly enhanced.
About Blood Pressure
What is Blood Pressure?
Blood pressure is the pressure exerted on the artery tube while blood flows through the arteries.
The pressure measured when the heart contracts and sends blood out of the heart is systolic
(highest). The pressure measured when the heart dilates with blood flowing back into the heart
is called diastolic (lowest) blood pressure.
Why Measure Your Blood Pressure?
Among the various health problems today, problems associated with high blood pressure are by
far the most common. High blood pressure's dangerously strong correlation with cardiovascular
diseases has made measuring blood pressure a necessity for identifying those at risk.
3
Blood Pressure Standard
The World Health Organization (WHO) has developed a blood pressure standard, according to
which areas of low- and high-risk blood pressure are identified. This standard, however, is a
general guideline and blood pressures vary between different people, age groups, etc.
It is important that you consult with your physician regularly. Your physician will tell you your
normal blood pressure range as well as the point at which you will be considered at risk.
Blood Pressure Fluctuation
Blood pressure fluctuates all the time!
You should not be overtly worried if you encountered two or three measurements at high levels.
Blood pressure changes over the month and even throughout the day. It is also influenced by
season and temperature.
4
Display Explanation
Display:
Date/Time indicator
Systolic Pressure
Memory Zones
Diastolic Pressure
Pulse Rate
Memory Number
Icons:
Memory Zone 1: Appears when the monitor is operated in memory zone 1
Memory Zone 2: Appears when the monitor is operated in memory zone 2
Weak Battery Mark: Appears when batteries should be replaced
Pulse Mark: Shows the pulse rate per minute
Memory Mark: Shows the number of stored measurements
Error Mark: Occurs when a mistake was made during measurement
5
Installing Battery
1. Press down and lift the battery cover in the direction of the arrow to open the battery
compartment.
2. Install or replace 4 “AA” sized batteries in the battery compartment according to the
indications inside the compartment.
3. Replace the battery cover by clicking in the bottom hooks first, then push in the top end of the
battery door.
You need to replace the batteries when:
1. low battery icon appears on display.
2. the ON/OFF/START button is pushed and nothing appears on display.
Caution:
Batteries are hazardous waste.
Do not dispose together with the household garbage.
Using the AC adapter
1.Connect the AC adapter with the AC adapter jack in the
back of the unit.
2.Plug the AC adapter into a standard wall socket.
Caution:
6
1. Please unload the batteries when operating
with the AC mode for a longer period of time.
Leaving the batteries in the compartment for
a long time may cause leakage, which may
lead to damage of the unit.
2. No batteries are needed when operating with the AC adapter.
Applying the arm cuff
1. Plug in the cuff connecting tube into the unit.
2. Unwrap the arm cuff, leaving the “Index” end of the cuff through the D-ring of the cuff.
y
3. Put your left arm through the cuff loop. The "OK" range indication should be positioned closer
to yourself with the rubber tube pointing in the direction of your arm. Position the artery mark
( ) over the main arteries (on the inside of your arm) in the upper arm.
y y
4. Turn your left palm upward
and place the edge of the arm
cuff
at
approximately
2
to
cm above the inner side of the elbow joint.
Tighten the cuff by pulling the "Index" end
of the cuff.
5. If the Index line falls within the OK range,
indicated at the edge of the cuff, this cuff
suitable for your use. If the Index line falls out
the OK range, you may need a special cuff
measurement. Please visit www.lumiscope.net
contact our service department at
800-672-8293 for more information regarding
3
is
of
for
or
1-
7
Measurement Procedure
1. Press the User-Switching key to select Memory Zone 1 or Memory Zone 2.
or
After a memory zone is selected, press the
measurement in the chosen memory zone.
button to reset the monitor so it can start
2. Press the
button. All digits will light up, checking the display functions. The checking
procedure will be completed after about 2 seconds.
3. After all symbols appear,
the
display will show a blinking “0”. The monitor is now ready to measure and will automatically
inflate the cuff slowly to start measurement.
8
Measurement Procedure
4. When the measurement is completed, the cuff will automatically deflate. Systolic, diastolic
and pulse will be shown simultaneously on the LCD screen. The measurement is then
automatically stored into the pre-designated memory zone.
Note:
1. This monitor automatically switches off approximately 1 minute after last measurement.
2. To interrupt the measurement, simply press any key. The cuff will deflate immediately after
any key is pressed.
3. Do not talk or move your arm or hand muscles during measurements.
9
Recalling Values from Memory
1. The Monitor has two Memory Zones (1 and 2). Each zone
can store up to 50 measurements.
2. To read memory values from a selected Memory Zone,
use the “User-Switching Key” to select a Memory Zone
(1 or 2) from which you want to recall values from. Then,
press the “M” key, and the values will be shown on the
LCD display with an assigned memory sequence number.
3. The monitor will display an average of the previous
measurements first. Every new press of the “M” key
calls for one set of prior values stored. Latest memory
will be recalled first. The calculated average will be
applied to a maximum of the last 3 memories.
10
Clearing Values from Memory
1. Press the User-Switching key to select the memory zone 1 or memory zone 2.
2. Continue to press and hold the “M” key for approximately 5 seconds, and the data in the predesignated memory zone will be erased automatically.
Press “M” Key for
5 seconds to clear all
memories
Note : The data in both memory zones (zone 1 and zone 2) will be erased if any of the batteries
are removed, or if the AC adapter is disconnected from the unit or unplugged from the
outlet. (It is suggested that users record their data on the Blood Pressure Log before
removing or replacing batteries.)
11
Time Adjustment
1. To adjust the date/ time in the monitor, press the
number showing the month.
key . The display will show a blinking
2. Change the month by pressing the “ ” Key. Each press will increase the number by one
in a cycling manner. Press the Key. again to confirm the entry, and the screen will show a
blinking number representing the date.
3. Change the date, the hour, and the minute as described in Step 2 above, using the “
to change and the
Set Key to confirm the entries.
4. A “0” will reappear as the Blood Pressure Monitor is ready for measurement again.
Press the
Set-key
blinking month
increasing month
confirm the entry
12
” Key
Helpful Tips
Here are a few helpful tips to help you obtain more accurate readings:
• Do not measure your blood pressure immediately after consuming a large meal. Wait at least
one hour after eating to take a measurement.
• Do not smoke or drink alcohol before measuring your blood pressure.
• You should not be physically tired or exhausted while taking a measurement.
• It is important that you relax during measurement. Take 15-minute rest before a reading.
• Do not take measurements if you are under stress or under tension.
• Take your blood pressure at normal body temperature. If you are feeling cold or hot, wait a
while before taking a measurement.
• If the monitor is stored at very low temperature (near freezing), have it placed at a warm
location for at least one hour before using it.
• Wait about 5 minutes in between consecutive measurements.
13
Troubleshooting
If any abnormality should arise during use, please check the following points.
Symptom
Check Point
Correction
No display when the
ON/OFF/START
key is pressed
Have the batteries run
down?
Replace them with four
new batteries or use AC
Adapter.
Have the batteries’
polarities been positioned
incorrectly?
EE mark shown
on display or the
blood pressure
value is displayed
excessively low
(high)
Is the cuff placed
correctly?
Re-insert the batteries in
the correct positions.
Wrap the cuff properly
so that it is positioned
correctly.
Did you talk or move
during measurement?
Measure again quietly.
Did you vigorously
shake the cuff during
measurement?
Note: If the unit still does not work, return it to your dealer or contact our repair department.
Under no circumstance should you disassemble and attempt to repair the unit by yourself.
14
Cautionary Notes:
1. The unit contains high-precision assemblies. Therefore, avoid extreme temperatures, humidity,
and direct sunlight. Avoid dropping or strongly shocking the main unit, and protect it from
dust.
2. Clean the blood pressure monitor body and the cuff carefully with a slightly damp, soft cloth.
Do not press. Do not wash the cuff or use chemical cleaner on it. Never use thinner, alcohol or
petrol (gasoline) as cleaner.
3. Leaky batteries can damage the unit. Remove the batteries when the unit is not used for a
long time.
4. The unit should not be operated by children so to avoid hazardous situations.
5. If the unit is stored near freezing, allow it to acclimate at room temperature before use.
6. Your Lumiscope Model 1131 is not field serviceable. You should not use any tool to open the
device nor should you attempt to adjust anything inside the device. If you have any problems,
please contact the store or the doctor from whom you purchased Lumiscope Model 1131 or
contact the Lumiscope Repair Department at 1-800-672-8293.
7. For users diagnosed with common arrhythmia (atrial or ventricular premature beats or atrial
fibrillation), diabetes, poor circulation of blood, kidney problems, or for users who have
suffered from stroke, the device might not be suitable for use.
8. Do not use on unconscious patients.
15
Specifications:
Measurement Method
Measurement Range
Pressure Sensor
Accuracy
Inflation
Deflation
Memory capacity
Auto-shut-off
Operation Environment
: Oscillometric
: Pressure: 20~280mmHg; Pulse: 40~180 beats/ minute
: Semi conductor
: Pressure: ± 3mmHg; Pulse: ± 5% of reading
: Pump Driven
: Automatic Pressure Release Valve
: 50 memories for each memory zone
: 1 minute after last button operation
: Temperature: 5 °C ~ 45 °C (41 °F~113 °F);
Humidity: 40 ~ 85%
Storage Environment
: Temperature: -10 °C ~ 60 °C (14 °F~140 °F ); Humidity: 10 ~
95%
Power Source
: 6V DC four LR06 (AA) Batteries
Dimensions
: 137 (L) X 140 (W) X 63 (H) mm
Weight
: 450g (G.W.) (No Batteries)
Arm circumference
: Adult: 24 ~36 cm (9.4”~14.2”) (standard)
: Large adult: 34 ~46 cm (13.4”~18.1”) (standard)
K.B.
: Short time operation 2 minutes.
*Specifications are subject to change without notice.
16
Two-Year Limited Warranty:
Lumiscope guarantees this product free from defects in material and workmanship for a period
of two years from the date of purchase, except as noted below:
This Lumiscope product warranty does not cover damage caused by misuse or abuse; the
attachment of any unauthorized accessory; alteration to the product; or any other conditions
whatsoever that are beyond the control of Lumiscope. Lumiscope shall not be responsible for
any type of incidental, consequential, or special damage. All implied warranties, including, but
not limited to those implied warranties of fitness and merchantability, are limited in the total
duration of two years from the original date of purchase.
To obtain warranty service on your Lumiscope Blood Pressure Monitor, please contact the
Lumiscope Repair Department at 1-800-672-8293 or visit www.lumiscope.net. There is a $15
fee for return shipping and handling. Please make checks payable to The Lumiscope Co., Inc.
Upon receipt, Lumiscope will repair or replace, as appropriate, the blood pressure monitor and
return it to you. Warranty is solely through the Lumiscope Repair Department. Service of this
product by anyone other than the Lumiscope Repair Department voids warranty.
In the event that Lumiscope does not abide by the terms of this warranty the consumer may
seek breach of contract remedies in the New York State Federal courts of law. This warranty
gives you specific legal rights and you may also have other rights which vary from state to state.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation may not apply to you.
Distributed By:
The Lumiscope Co., Inc.
www.lumiscope.net
Repair Department: 1-800-672-8293
Made and Printed in China
17