Maytag MER8772W User's Manual

Add to my manuals
1 Pages

advertisement

Maytag MER8772W User's Manual | Manualzz

30" (76.2 cm) Freestanding Electric Range

PRODUCT MODEL NUMBERS

MER8770W

MER8772W

MER8875W

Electrical: To properly install your range, you must determine the type of electrical connection you will be using and follow the instructions provided for it here.

● Range must be connected to the proper electrical voltage and frequency as specified on the model/serial number rating plate. The model/serial number rating plate is located behind the control panel or on the oven frame behind the storage drawer or warming drawer panel. Refer to the figures in the “Product Dimensions” section of the “Location

Requirements” section.

● This range is manufactured with the neutral terminal connected to the cabinet. Use a 3-wire, UL listed, 40- or 50-amp power supply cord

(pigtail) (see following Range Rating chart). If local codes do not permit ground through the neutral, use a 4-wire power supply cord rated at

250 volts, 40 or 50 amps and investigated for use with ranges.

Range Rating*

120/240 Volts

8.8 - 16.5 KW

16.6 - 22.5 KW

120/208 Volts

7.8 - 12.5 KW

12.6 - 18.5 KW

Specified Rating of

Power Supply Cord Kit and Circuit Protection

Amps

40 or 50**

50

*The NEC calculated load is less than the total connected load listed on the model/serial rating plate.

**If connecting to a 50-amp circuit, use a 50-amp rated cord with kit. For 50-amp rated cord kits, use kits that specify use with a nominal 1 ³⁄₈" (34.9 mm) diameter connection opening.

● A circuit breaker is recommended.

CABINET OPENING DIMENSIONS

Cabinet opening dimensions shown are for 25"

(64.0 cm) countertop depth, 24" (61.0 cm) base cabinet depth and 36" (91.4 cm) countertop height.

IMPORTANT: If installing a range hood or microwave hood combination above the range, follow the range hood or microwave hood combination installation instructions for dimensional clearances above the cooktop surface.

* NOTE: 24" (61.0 cm) minimum when bottom of wood or metal cabinet is covered by not less than 1⁄4" (0.64 cm) flame retardant millboard covered with not less than No. 28

MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024"

(0.6 mm) aluminum or 0.020" (0.5 mm) copper.

30" (76.2 cm) minimum clearance between the top of the cooking platform and the bottom of an uncovered wood or metal cabinet.

PRODUCT DIMENSIONS

F

A

E

D

B

A

C

F

G

H

D

G

F

J

I

E

K

L

C*

B*

A. 28

¹⁄₂" (72.4 cm) to 29" (73.7 cm) depth with handle to backguard standoff (depending on model)

B. 46

⁵⁄₈" (118.4 cm) to 47¼" (120.0 cm) overall height (depending on model)

C. 35

⁵⁄₈" (90.5 cm) cooktop height (minimum)

D. 29

⁷⁄₈" (75.9 cm) width

E. 26

³⁄₄" (67.9 cm) depth to backguard standoffs

F. Model/serial rating plate (located on the left side frame behind storage or warming drawer panel)

*Range can be raised approximately 1" (2.5 cm) by adjusting the leveling legs.

Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.

A. 13" (33.0 cm) upper cabinet depth

B. 30" (76.2 cm) min. opening width

C. For minimum clearance to the top of the cooktop, see NOTE*

D. 30

¹⁄₈

" (76.5 cm) min. opening width

E. Junction box in shaded area

F. 3

⁵⁄₁₆

" (8.4 cm)

G. 7" (14.6 cm)

H. 9

¹⁄₂

" (24.1 cm)

I. 7" (14.6 cm)

J. 22" (55.9 cm)

K. 3" (7.6 cm)

L. Cabinet door or hinge should not extend into the cutout.

Dimensions are for planning purposes only. For complete details, see Installation

Instructions packed with product. Specifications subject to change without notice.

Ref. W10258095A

7/27/09

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement