Metra Electronics NISSAN MURANO 99-7426 Installation instructions

INSTALLATION INSTRUCTIONS FOR PART 99-7426

APPLICATIONS

Nissan Murano 2009-10

(Without Bose Audio)

(Climate Controls must be above OE radio)

99-7426

KIT FEATURES

• DIN Mount Radio Provision with Pocket

• ISO Mount Radio Provision with Pocket

• Double DIN Radio Provision

• Stacked ISO Mount Units Provision

• Painted Charcoal To Match OEM Finish

KIT COMPONENTS

A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets

E) Double DIN Trim Plate • F) Pocket

A

B C

D

E

Harness & Antenna Connections (sold separately)

• 70-7552 - Nissan Harness 07-up

• 40-NI12 - Nissan Antenna Adapter 07-up

F

TOOLS REQUIRED:

Small Flat Blade Screwdriver or Panel Removal Tool

• Phillips Screwdriver

1-800-221-0932 www.metraonline.com

© COPYRIGHT 2010 METRA ELECTRONICS CORPORATION

99-7426

TABLE OF CONTENTS

• Dash Disassembly

- Nissan Murano 2009-10 ............................................1, 2

• Kit Assembly:

- DIN Mount Radio Provision with Pocket ........................3

- ISO Mount Radio Provision with Pocket ........................4

- Double DIN Radio Provision ..........................................5

- Stacked ISO Mount Units Provision................................5

•Final Assembly ..............................................................6

*Note:

Refer also to the instructions included with the aftermarket radio.

99-7426 DASH DISASSEMBLY

NISSAN MURANO 2009-10

1 Disconnect the negative battery terminal to prevent an accidental short circuit.

A

2 Unclip trim panel at bottom center of dash. (Figure A)

3 Remove (1) Phillips screw from bottom of each side trim panel. Unclip and remove the side trim panels.

(Figure B)

4 Remove (3) Phillips screws securing the climate control then unclip, unplug and remove it from the sub dash. (Figure C)

Continued on next page.

B

C

1

99-7426 DASH DISASSEMBLY

NISSAN MURANO 2009-10

D

5 Remove (2) Phillips screws from the panel below the radio (containing the passenger air bag light) then unclip, unplug and remove the panel.

(Figure D)

6 Remove (6) Phillips screws securing the radio to the sub dash. Unplug and remove radio. (Figure E)

Continue to kit assembly.

E

2

99-7426 KIT ASSEMBLY

DIN MOUNT RADIO PROVISION WITH POCKET

* Note: Refer also to the instructions included with the aftermarket radio.

A

1 Slide the DIN cage into the radio housing and secure by bending the metal locking tabs down. (Figure A)

2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B)

3 Snap the pocket into the radio housing.

(Figure C)

Continue to final assembly.

B

C

3

99-7426 KIT ASSEMBLY

ISO MOUNT RADIO PROVISION WITH POCKET

* Note: Refer also to the instructions included with the aftermarket radio.

A

1 Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure A)

2 Slide the radio into the radio housing until it snaps into place. (Figure B)

3 Snap the Trim plate onto the front of the Radio Housing. (Figure B)

4 Snap the pocket into the radio housing. (Figure C) B

Continue to final assembly.

C

4

99-7426 KIT ASSEMBLY

DOUBLE DIN RADIO PROVISION

STACKED ISO MOUNT UNITS PROVISION

* Note: Refer also to the instructions included with the aftermarket radio.

A

1 Cut and remove the center bar from the radio housing. (Figure A)

2 Snap the Double DIN brackets to the inside edge of the radio housing.

(Figure B)

3 Slide the Double DIN or ISO mount unit(s) into the bracket/radio housing assembly and secure the unit(s) to the assembly using the screws supplied with the unit(s). (Figure C)

4 Snap the Double DIN trim plate onto the front of the radio/housing.

(Figure C)

B

Continue to final assembly.

C

5

A

B

99-7426 FINAL ASSEMBLY

FINAL ASSEMBLY

(A) Strip wire ends back 1/2"

B) Twist ends together

C) Solder

D) Tape

C

D

1

2

Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.)

Re-connect the negative battery terminal and test the unit for proper operation.

Reassemble radio and dash assemblies in reverse order of disassembly. 3

FINAL WIRING CONNECTIONS

Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit.

METRA / EIA WIRING CODE

12V Ignition / Acc. . . . . . . . . . Red

12V Batt / Memory. . . . . . . . . Yellow

Ground. . . . . . . . . . . . . . . . . . Black*

Power Antenna. . . . . . . . . . . . Blue

Right Front (+) . . . . . . . . . . . . Gray

Right Front (-). . . . . . . . . . . . . Gray/ Black

Left Front (+) . . . . . . . . . . . . . White

Left Front (-). . . . . . . . . . . . . . White / Black

Right Rear (+) . . . . . . . . . . . . Violet Amp Turn-On . . . . . . . . . . . . . Blue / White

Amp Ground. . . . . . . . . . . . . . Black / White

Illumination . . . . . . . . . . . . . . Orange

Dimmer . . . . . . . . . . . . . . . . . Orange / White

Right Rear (-) . . . . . . . . . . . . . Violet / Black

Left Rear (+) . . . . . . . . . . . . . Green

Left Rear (-) . . . . . . . . . . . . . . Green / Black

*NOTE: When a Black wire is not present, ground radio to vehicle chassis.

All colors may not be present on all leads due to manufacturer’s specifications.

1-800-221-0932 www.metraonline.com

REV. 04/27/10 © COPYRIGHT 2010 METRA ELECTRONICS CORPORATION INST99-7426

6