advertisement
Operating and Installation
Instructions
Freezer with Ice Maker
F 1411 SF
To prevent accidents and appliance damage read these instructions before installation or use.
en - US, CA
M.-Nr. 09 743 950
Contents
IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Contents
IMPORTANT SAFETY INSTRUCTIONS
When using the appliance, follow basic safety precautions, including the following:
Read all instructions before installation and use to prevent accidents and machine damage.
This appliance is intended for residential use only. Use only as described in this Operating manual.
Only use the appliance for its intended purpose.
This appliance complies with current safety requirements. Improper use of the appliance can lead to personal injury and material damage.
Keep these operating instructions in a safe place and pass them on to any future user.
Electrical Safety
~
Before installation, make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply. This data must correspond to prevent injury and machine damage. Consult a qualified electrician if in doubt.
~
Before installation or service, disconnect the power supply to the work area by unplugging the unit,
"tripping" the circuit breaker or removing the fuse.
~
Do not use an extension cord to connect this appliance to electricity.
Extension cords do not guarantee the required safety of the appliance
(e.g., danger of overheating).
~
Be certain your appliance is properly installed and grounded by a qualified technician. To guarantee the electrical safety of this appliance continuity must exist between the appliance and an effective grounding system. It is imperative that this basic safety requirement be met. If there is any doubt, have the electrical system of the house checked by a qualified electrician.
~
Only connect power to the appliance when all installation and plumbing work is complete.
4
IMPORTANT SAFETY INSTRUCTIONS
Installation
This appliance is top-heavy and must be secured to prevent the possibility of tipping forward.
Keep the door closed until the appliance is completely installed and secured per installation instructions.
~
This appliance must be installed and connected in compliance with the installation instructions.
~
Installation and repair work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and may void the warranty.
~
Installation must comply with local plumbing regulations and state laws.
~
Do not operate any appliance with a damaged cord or plug, or if the appliance has been damaged in any manner. Contact Miele’s Technical Service Department.
~
This appliance must not be used in a non-stationary location (e.g. on a ship).
~
Do not install the freezer in a room with too low an ambient temperature, e.g., a garage, as this may lead to the appliance switching off for longer periods so that it cannot maintain the required temperature.
~
In appliances with an automatic ice maker, avoid contact with the moving parts of the ejector mechanism, or with the heating element located on the bottom of the ice maker. Do not place fingers or hands on the automatic ice making mechanism while the freezer is plugged in.
~
The ice cube maker is not suitable for connection to a hot water supply.
~
Do not use water that is microbiologically or chemically unsafe or of unknown quality without adequate disinfection or other treatment before or after the filter is used; the filter alone is not an adequate safeguard.
Use
~
This appliance is not designed for commercial use. It is intended for use in domestic households and in similar working and residential environments such as:
– shops, offices and similar work environments
– by customers in hotels, motels, Bed
& Breakfasts or similar residential environments.
~
This appliance is not intended for outdoor use.
~
The appliance is only intended for residential use to store frozen foods, freeze fresh foods and prepare ice.
All other uses are prohibited and may be dangerous.
5
IMPORTANT SAFETY INSTRUCTIONS
~
Persons who lack physical, sensory or mental abilities, or experience with the machine should not use it without supervision or instruction by a responsible person.
~
To reduce the risk of injury, do not allow children to play in, on or near the appliance, especially in the door hinge area.
~
After your freezer is in operation, do not touch the cold surfaces in the freezer compartment, particularly when hands are damp or wet. Skin may adhere to these extremely cold surfaces.
~
Do not refreeze frozen foods which have thawed completely.
~
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
~
Do not deactivate the water filter display.
~
Do not use sharp-edged objects to remove frost and ice, or separate frozen foods and remove ice trays.
They will damage the evaporator, causing irreversible damage to the appliance.
~
Do not use defrosting sprays or de-icers, as they might contain substances which could damage the plastic parts or which could cause a build-up of gases and pose a danger to health.
~
Do not use any oils or grease on the door seal, as these will cause the seal to deteriorate and become porous with time.
~
Do not block the ventilation gaps in the plinth or the top of the appliance housing unit, as this can impair the efficiency of the appliance, increase the electricity consumption and cause damage to the appliance.
~
Never use a steam cleaner to clean the appliance. Pressurized steam could damage electrical components and cause a short circuit.
6
IMPORTANT SAFETY INSTRUCTIONS
Disposal of your old appliance
~
Before disposing of an old appliance, first make the door latch or lock unusable.
~
Take off the door.
~
Leave the shelves in place so that children may not easily climb inside.
~
Consult with your municipal policy on recycling.
~
Be careful not to damage any part of the pipework while awaiting disposal by:
-
-
puncturing the refrigerant channels in the evaporator.
bending any pipework.
scratching the surface coating.
Splashes of refrigerant can damage the eyes.
~
Your old freezer may have a cooling system that used CFCs
(chlorofluorocarbons). CFCs are believed to harm stratospheric ozone.
If you intentionally release this CFC refrigerant, you can be subject to fines and imprisonment under provisions of environmental legislation. Make sure the
CFC refrigerant is removed and disposed of by a qualified technician.
SAVE THESE
INSTRUCTIONS
7
Guide to the freezer a Door shelves (height adjustable) b Shelves (height adjustable) c Ice cube maker d Ice cube container e Control panel f Main switch to turn the appliance
On/Off g Freezer baskets h Water filter
8
Guide to the freezer
Control panel
a Access button "p" b Temperature display
X colder; Y warmer
Allows you to set the desired temperature in the freezer c On/Off sensor button for the
SuperCool function d On/Off sensor button for the ice cube maker e Sensor button for the temperature and door alarm* f Water filter change indicator*
* Only visible when the relevant function is activated
9
Before use
Before using for the first time
The stainless steel surface of the appliance is protected with a plastic film, which protects it during shipping.
Do not remove this protective film until the appliance has been completely installed.
After removing the protective film clean the exterior surface with the supplied stainless steel agent. This will aid in preventing resoiling.
^ Clean the inside of the appliance and the accessories with a mild solution of warm water and liquid dish soap.
Dry with a soft cloth.
Turning the appliance On/Off
^ Open the appliance door.
^ Turn the appliance On/Off with the main switch.
The main switch is located on the right-side underneath the control panel.
Once on, the appliance begins cooling.
When the door is open, the interior lights come on.
If the appliance was transported to the installation site horizontally, leave the appliance standing upright for approx. 8 hours before connecting it to the electrical supply.
This is very important to ensure correct functioning.
The access button will light in the control panel.
The preset temperatures (factory default settings) are reached after a few hours. Do not put any food in the appliance until the preset temperatures are reached.
,
Turning off the appliance with the main switch does not safely isolate it from the power supply.
10
Settings
Using the settings
This appliance is operated with the use of touch keys activated by a finger.
– An available button will appear white.
– A selected button will appear yellow.
Additional settings
In the settings mode you can select and change functions.
In settings mode, certain settings can be changed. The function possibilities are described in the respective chapters of this manual.
Overview of the selectable function settings:
^ Touch the access button "p" so it turns yellow.
On the control panel you will see additional sensor buttons to operate the appliance.
These buttons allow you to:
– adjust the temperature,
– select the SuperCool function, or
– turn the ice maker On/Off.
For additional information, see the corresponding sections in this manual.
Function
To enter and exit the
Settings mode
Temperature unit
°C - °F
(see "Setting the temperature")
RemoteVision
Module settings
(optional accessory)
Button sound on/off
(see "Settings")
No function
Display text
c
†
;
=
^
^ To leave the settings menu, touch the access button " p" so it turns white.
The last settings entered are stored.
If the access button is not pressed the display will go out after approx.
30 secs.
The other sensor buttons now disappear from the control panel.
11
Settings
Turning the button sound
On/Off
If you prefer the buttons to be silent when touched the button sound can be turned off.
^ While holding down the X button, press the access button " p" once.
Keep holding the
X button down until the following appears in the display
(approx. 5 seconds).
^ Touch the access button "p" so it turns yellow.
^ Note the position of the X button, but do not touch.
^ Touch the access button "p" again so it turns white.
Only the access button " p" is visible.
^ Place one finger on the position of the X button and hold (the X button will not be visible).
^ Tap the X button until = appears in the display.
^ Touch the access button "p" to confirm.
^ By touching the X button, you can choose between:
= 0 : Button sound is off
= 1 : Button sound is on
= – : Return to menu.
^ Touch the access button "p" to confirm the setting.
^ Tap the X button until you see ; in the display.
^ Touch the access button "p".
You have now left the Custom settings mode.
When you are in the Custom settings mode the door alarm is turned off automatically. Once the door is closed it is reactivated.
12
Turning off for longer periods of time
If the appliance is not going to be used for an extended time (for example, during a vacation) some precautions need to be taken:
^ Shut off the water supply line,
(several hours before switching off the appliance)
^ Take all food out of the appliance
^ Turn the appliance off
^ Unplug the appliance
^ Empty the ice cube container
^ Clean the interior
^ Remove and discard the water filter
(secure the filter cap)
^ Leave the door open to prevent odors
Settings
13
Temperature and door alarm
The appliance is equipped with an alarm system, to ensure that the temperature does not rise unnoticed because of energy loss or an open door.
The alarm system is always operational, it does not need to be switched on.
Turning the temperature alarm Off
As soon as the alarm condition is corrected, the alarm signal turns off and the affected zone stops flashing in the display. The "alarm" indicator goes out.
Temperature alarm
If the temperature becomes too warm, an alarm sounds and the "alarm" indicator turns red and flashes and the temperature flashes in the control panel.
The temperature display shows the highest temperature reached during the alarm.
The alarm will sound and the display will flash if:
– too much warm air flows into the appliance, for example when food is being loaded, re-arranged, or taken out.
– large amounts of food are being frozen at once.
– the power fails.
As soon as the alarm condition is corrected the alarm with turn off and the sensor button for alarm will go out.
^ To turn the alarm off early, press the "alarm" sensor button.
The alarm signal turns off. The "alarm" indicator remains on until the alarm condition is corrected.
If the temperature in the freezer zone reaches 0°F (-18°C) or higher, check that food has not defrosted.
Door alarm
If the appliance door is left open, an alarm signal will sound and the "alarm" indicator will turn red after five minutes.
Once the door is closed the alarm will turn off and the "alarm" indicator will go out.
Turning the door alarm Off
To turn the alarm off early:
^ The "alarm" indicator and signal will turn off.
The alarm will turn off and the "alarm" indicator will go out.
14
Setting the temperature
Setting the temperature
^ Touch the access button "p" so it turns yellow.
^ Use the X and Y buttons next to the temperature display to set the temperature warmer or colder.
Tap the
X and Y sensor buttons to raise/lower the temperature 1°, or hold it down to move through the temperature range more quickly.
The temperature display on the control panel always shows the
desired temperature.
Temperature range
The temperature can be set within the following range:
7°F to -11°F (-14°C to -24°C).
To freeze fresh food and store frozen food for an extended period of time, a temperature of 0°F (-18°C) is suggested.
The room temperature and the installation location can affect the time it takes for the appliance to drop to the coldest temperature. If the room temperature is too high, it may not be possible for the appliance to reach the lowest temperature.
15
Setting the temperature
Temperature unit
(Fahrenheit/Celsius)
The temperature can be displayed in degrees Fahrenheit (°F) or Celsius (°C).
^ While holding down the X button, press the access button " p" once.
Keep holding the X button down until the following appears in the display
(approx. 5 seconds).
^ Touch the access button "p" so it turns yellow.
^ Note the position of the X button, but do not touch.
^ Touch the access button "p" again so it turns white.
Only the access button " p" is visible.
^ Place one finger on the position of the X button and hold (the X button will not be visible).
^ Tap the X button until † appears in the display.
^ Touch the access button "p" to confirm.
^ By touching the X button you can select either Fahrenheit or Celsius for the temperature display.
† 0: Fahrenheit
† 1: Celsius
† –: return to menu.
^ Touch the access button "p" to confirm the setting.
^ Tap the X button until a ; appears in the display.
^ Touch the access button "p".
You have left the Custom settings mode.
When you are in the Custom settings mode the door alarm is turned off automatically. Once the door is closed it is reactivated.
16
Using the freezer efficiently
Freezing food
Fresh food should be frozen as quickly as possible. This helps maintain the nutritional value, vitamin content, appearance and taste of the food.
Never refreeze partially or fully defrosted food. Consume defrosted food as soon as possible, it will lose its nutritional value and spoil if left for too long. Do not refreeze defrosted food unless it has been cooked.
Before placing food in the freezer
^ When you are planning to freeze large amounts of food (more than
4 ½ lbs [2 kg]), switch on the
SuperCool function ahead of time
(see "SuperCool").
This will provide the food already in the freezer with a protective boost of cold air.
Placing food in the freezer
Food to be frozen can be placed anywhere in the freezer.
The freezer baskets can hold a maximum of 35 lbs (16 kg) of frozen food.
^ Spread the food to be frozen across the bottom of the freezer basket or across the shelves, so that it will freeze through to the core as quickly as possible.
^ When placing items in the freezer, make sure the packaging and containers are dry, to keep them from sticking together when frozen.
When freezing, try not to let frozen food come into contact with unfrozen food, this could cause the frozen food to defrost.
17
Using the freezer efficiently
Defrosting
Frozen food can be defrosted in different ways:
– in a microwave oven,
– at room temperature,
– in the refrigerator (the cold given off by the frozen food helps to keep the other food cold),
– in a steam oven.
Poultry It is especially important to observe proper hygiene when defrosting poultry. Never save the liquid from defrosted poultry. Drain it away and promptly wash the container, the sink and your hands. Danger of salmonella poisoning.
Fruit should be defrosted at room temperature in its packaging, or in a covered bowl.
Most vegetables can be cooked while still frozen. Simply place directly into boiling water or hot oil.
Cooling drinks quickly
To cool drinks quickly, switch on the
SuperCool function. See "SuperCool" for more information.
Do not leave bottles in the freezer for more than 1 hour, closed containers could burst.
18
Using the freezer efficiently
Freezing tips
– The following are examples of foods
suitable for freezing:
Fresh meat, poultry, game, fish, vegetables, herbs, fresh fruit, pastry/dough, leftovers, and a range of pre-cooked meals.
– The following examples of foods not
suitable for freezing:
Lettuce, radishes, sour cream, mayonnaise, eggs in their shells, onions, whole raw apples and pears.
– To retain color, taste and vitamin C, vegetables should be trimmed, washed, and blanched.
To blanch: bring a large saucepan of water to a boil, then submerge the vegetables in rapidly boiling water for 2-3 minutes, depending on type.
Remove, and plunge into ice-cold water to cool quickly. Drain and pack for freezing.
– Lean meat freezes better than fatty meat, and can be stored for considerably longer.
– To prevent chops, steaks, cutlets or rolled meats from freezing together in solid blocks when packed, separate with a sheet of plastic freezer wrap.
– Do not season fresh foods or blanched vegetables before freezing. Cooked food can be lightly seasoned before freezing, but care should be taken as the taste of some spices alters when frozen.
– Do not place hot foods or drinks in the freezer. This causes already frozen food to thaw, and increases the energy consumption considerably. Allow hot foods and drinks to cool down before placing them in the freezer.
Packing tips
^ Unsuitable packing material
- wrapping paper
- greaseproof paper
- cellophane
- garbage bags
- plastic shopping bags
Suitable packing material
- plastic freezer bags/wrap
- aluminum foil
- freezer containers
^ To help prevent freezer burn, expel as much air as possible from bags, etc., before sealing them.
^ Close the packaging tightly with
- plastic clips
- twist ties
- rubber bands
^ Mark the package to indicate the contents and the date of freezing.
19
SuperCool
When the SuperCool function is activated, the appliance is cooled as cold as possible (to a factory-preset temperature).
SuperCool
The SuperCool function is ideal for freezing large quantities of unfrozen food. Ideally the function should be switched on 4 - 6 hours before the food is placed in the freezer.
If the max. freezing capacity is used,
24 hours are recommended.
This helps food to freeze quickly and retain its nutrients, vitamins, flavor and appearance.
Switching on SuperCool
Switching off SuperCool
The SuperCool function automatically switches off after approx. 52 hours. The sensor button turns white, and the appliance continues running at normal power.
To save energy, you can switch off the
SuperCool function once the food is sufficiently chilled.
^ Touch the SuperCool sensor so that it turns white.
The temperature display returns to the original temperature setting.
The appliance now continues running at normal power.
^ Touch the SuperCool sensor so that it turns yellow.
The temperature now begins to fall, with maximum cooling performance.
The new temperature setting appears in the display -22°F (-30°C).
20
Ice cube maker
For the automatic ice cube maker to operate, it must be connected to the household water supply. See
"Plumbing".
Once the ice cube container is full, the ice cube maker switches off automatically.
Turning on the ice cube maker
^ Make sure that the ice cube container is under the ice cube maker, as far as possible.
Do not use the ice cube container for rapid cooling of food or drinks.
The ice cube maker may become blocked and be damaged.
Ice cubes will not be produced unless the container is completely closed.
^ Touch the sensor button for the ice cube maker so that it turns yellow.
As soon as the freezer has cooled to a freezing temperature, the ice cube container fills with water. Cold air is blown directly over the container.
As soon as the ice cubes are frozen, they fall into the ice cube container.
The ice cube maker can produce approx. 120 ice cubes within 24 hours.
Note: Ice production will vary due to your water supply temperature, pressure and hardness.
The production volume of the ice depends on the temperature in the freezer. The lower the temperature the more ice cubes produced.
After the appliance is turned on for the very first time, it can take up to 10 hours for the first ice cubes to drop out of the ice cube maker and collect in the container.
Do not use the first three containers of ice cubes from the ice cube maker.
Discard the ice produced in the first
24 hours after switching on the ice cube maker.
This applies for the very first use, and whenever the appliance has been out of service for an extended period of time.
The amount of ice cubes produced depends on the temperature in the freezer section. The lower the temperature, the more ice cubes will be produced in a given period of time.
Turning off the ice cube maker
The water supply line must be shut off several hours before the appliance or ice cube maker is switched off.
^ Touch the sensor button for the ice cube maker so that it turns white.
21
Automatic defrost
The freezer defrosts automatically.
The moisture generated in the appliance collects in the evaporator. It is automatically defrosted and dissipated by the condenser periodically.
This automatic defrosting system enables the freezer to remain permanently ice-free, while ensuring that the food stored in the freezer stays frozen.
22
Adjusting the interior fittings
Moving the shelves
The shelves can be adjusted according to the height of the food.
^ Using both hands, grasp the shelf from underneath and lift slightly so that the rear of the shelf is slightly above the mountings.
^ Pull the shelf forward.
^ Move the shelf to the desired height, then insert the (rear) hooks into place.
^ Make sure the shelf is level.
Replacing a door shelf
^ Start at the top of the slide-rails and slide the shelf down into the desired position.
Freezer baskets
For easier loading, unloading, and cleaning, the freezer baskets can be shifted or completely removed.
^ Pull the basket forward until resistance is felt.
On the hinged-side of the door is a safety lock, which must be turned to a horizontal position before the drawer can be removed.
Top shelf
^ Lift the shelf up and out.
^ When replacing the shelf, make sure that the latches on the corners at the back are correctly engaged.
Adjusting the door shelves
For easier loading, unloading, and cleaning, the door shelves can be shifted or completely removed.
^ Using both hands, grasp the door shelf by the frame and tip it slightly forward.
^ Slide the tipped shelf up or down along the slide-rails, and click it into place with the lower hooks.
^ Make sure the shelf is level.
Removing a door shelf
^ Slide it upward all the way to the top of the slide-rails, until it can be removed.
^ Using a suitable object, e.g., coin, turn the safety lock to a horizontal position a.
^ On both sides of the basket, pull the latches b upward and lift the basket out of the freezer.
Replacing the freezer basket
^ Fully extend the telescopic tracks.
^ Lay the basket onto the tracks so that it connects in the front and back.
^ Turn the safety lock back to the vertical position.
^ Slide the freezer basket in.
23
Adjusting the interior fittings
Ice cube container
The ice cube container is set on telescopic tracks, and can be removed for loading, unloading and cleaning.
^ Slide the container forward until resistance is felt.
^ On both sides of the container, pull the latches (see arrow) upward and lift the container out of the freezer.
Push the tracks back into the freezer to avoid injury.
Replacing the ice cube container
^ Completely extend the telescopic tracks.
^ Lay the container onto the tracks so that it connects in the front and back.
^ Slide the ice cube container completely in.
24
Cleaning and care
To reduce the risk of electrical shock, disconnect the appliance from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before maintenance.
Never use cleaning agents containing abrasive substances such as sand, soda, acids, chlorides or chemical solvents.
Non-abrasive cleaning agents are also unsuitable, as they can cause matte areas to appear.
Stainless steel surfaces can be cleaned using a non-abrasive stainless steel cleaner (available from Miele).
Only use a mild solution of warm water and liquid dish soap to clean this appliance.
Do not use a steam cleaner to clean this appliance. Pressurized steam could penetrate electrical components and cause a short circuit.
Do not allow water to get into the electronic unit or lights.
The data plate located inside the appliance must not be removed. It contains information which is required in the event of a service call.
To better maintain your appliance avoid the following:
– cleaners containing soda, ammonia, thinners, or chlorides
– cleaners containing descaling agents or lime removers,
– abrasive cleaners,
– dishwasher soap (powder),
– caustic (oven) cleaners,
– scouring pads, steel wool, hard brushes,
– metal scrapers,
– eraser sponges,
– steam cleaning products.
Glass cleaners may be used to clean the exterior. However do not allow them to sit or "puddle", this can cause damage to the surface.
Remove the cleaner promptly.
25
Cleaning and care
Before cleaning Appliance door
^ Stainless steel surfaces can be cleaned using a non-abrasive stainless steel cleaner.
^ To help prevent resoiling, a conditioner for stainless steel can also be used. Apply sparingly with even pressure.
^ Use the main switch to turn the appliance off completely.
The main switch is located on the right side underneath the control panel.
^ Unplug the power cord.
^ Remove any food from the appliance and store it in a cool place.
^ Take out any removable parts, e.g., shelves.
Aluminum frames
The shelf frames and the door baskets are made of aluminum.
^ Clean the frames with a mild solution of warm water and liquid dish soap.
Aluminum is susceptible to scratches and nicks, treat with care.
Cleaning the interior and accessories
Use a mild solution of warm water and liquid dish soap. Wash all accessories and drawers by hand. Do not wash in a dishwasher.
^ Clean the appliance as needed.
^ After washing, wipe down the interior and accessories with a clean wet cloth, then dry with a soft cloth.
Leave the appliance door open for a short time, so the moisture can evaporate.
The aluminum frames may become discolored or otherwise altered if soiling is not cleaned away promptly.
Do not use stainless steel cleaners; lime removers; scouring pads, such as pot scrubbers; or used sponges that still contain abrasive cleanser residue to clean the frames.
26
Cleaning and care
Ventilation slits
^ Check the ventilation slits in the base panel regularly. Remove any dirt/dust with a vacuum cleaner or brush. Clean as needed.
Door seals
Do not use any oils or grease on the door seals. This may cause the seals to deteriorate and become porous over time.
^ Clean the door seals with warm water and dry with a soft cloth.
After cleaning
^ Return all shelves and accessories.
^ Shut the appliance door, plug in the appliance and turn it on with the main switch.
^ Turn on the SuperCool function. The freezer section will cool down quickly.
^ Once the temperature is cold enough, place the freezer baskets containing the frozen food into the freezer.
^ Turn off the SuperCool function on a temperature of 0 °F (-18 °C) is reached.
27
Cleaning and care
Changing the light bulb
The lighting automatically switches off after the door has been open for approx. 5 minutes. This is not a fault.
After the bulb has cooled for a short time it will turn on again.
If the light does not come on when the door is opened briefly, the light bulb should be changed.
^ Use the main switch to turn the appliance off.
To reduce the risk of electric shock, disconnect the appliance from the power supply by unplugging or tripping the circuit breaker.
Upper lighting
^ Remove the defective light bulb.
^ Place the new bulb in the socket.
Halogen bulb type:
20 W/12 V/socket GY 6.35.
^ Slip the rear of the light cover back into position, then pull it forward and into place.
^ Grasp the front of the light cover with both hands, and slide it back.
^ Carefully pull the cover forward and out.
Never touch a halogen bulb with bare fingers.
When inserting a glass halogen bulb always hold with a soft cloth.
28
Side lighting
^ Turn the light cover counterclockwise and pull out.
Never touch a halogen bulb with bare fingers.
When inserting a glass halogen bulb always hold with a soft cloth.
Cleaning and care
^ Pull the defective light bulb from the socket.
^ Place the new bulb in the socket.
Halogen bulb type:
5 W/12 V/socket G 4.
^ Put the light cover back on and turn clockwise into place.
^ Restore power to the appliance.
29
Water filter
The appliance is supplied with an active charcoal filter which improves the taste and smell of ice cubes by removing chlorine and other substances from the incoming tap water.
Additional water filters are available from Miele.
It is important to change the water filter regularly.
To avoid serious illness or death, do not use water that is microbiologically or chemically unsafe or of unknown quality without adequate disinfection or other treatment before or after use of a filter.
Note:
– After installing a new water filter and switching on the ice maker, discard the first 24 hours' worth of ice production.
– If the ice maker has not been used for a prolonged time discard any ice cubes in the freezer, empty the container and discard the ice production of the next 24 hours.
– If the appliance or ice maker have not been routinely used for several weeks or months, or if the ice cubes have an unpleasant odor, change the water filter.
Water filter change indicator
The change indicator will appear approx. every 6 months depending on the quantity of ice produced.
– When the filter indicator lights red, this is an indication that a filter change will soon be necessary.
New water filters (Bypass and Active charcoal filters) are available from
Miele.
^ When the filter indicator flashes red in the display the filter must be changed.
30
Water filter
Exchanging the water filter
Note: Air trapped in the system may cause water and the filter cartridge to eject forcefully. Use caution when removing.
^ Push in and rotate the filter cap on the base panel of your appliance counterclockwise 180°, 1.
^ Pull the used filter cartridge out of the appliance, 2.
^ Remove the cap from the used filter,
3.
^ Take a new filter cartridge out of the packaging and remove the protective cap.
^ Push the cap onto the new filter cartridge, 4.
^ Push the filter cartridge with cap, in a horizontal position, all the way into the opening in the base panel, 5.
^ Rotate the filter cartridge clockwise
180° until the cap is in a horizontal position, 6.
31
Water filter
^ After the filter change the filter indicator in the display still flashes.
The change must be be confirmed in the electronic.
Using an external water filter
If your household water supply already has an external water filter installed, leave the standard water filter (bypass cartridge) installed in the appliance.
Confirming the filter change
^ Press and hold the filter change sensor button.
^ At the same time place a finger on the access button. Press and hold both sensor buttons for approx. 5 seconds until a beep is heard.
The water filter change has been confirmed and the filter change indicator had been reset.
The filter change indicator goes out.
^ Close the door.
After installing a new water filter discard the first 24 hours of ice production.
32
Water filter
Trademark/Model Designation
9000 077095
Miele 07134220
Manufacturer: Cuno, Incorporated
State of California
Department of Public Health
Water Treatment Device
Certificate Number
06 1775
Date Issued: March 10, 2006
Date Revised: April 3, 2008
Replacement Elements
9000 077104
07134220
The water treatment device(s) listed on this certificate have met the testing requirements pursuant to Section
116830 of the Health and Safety Code for the following health related contaminants:
Microbiological Contaminants and Turbidity
Cysts
Turbidity
Organic Contaminants
None
Inorganic/Radiological Contaminants
None
Rated Service Capacity: 740 gals Rated Service Flow: 0.75 gpm
Conditions of Certification:
Do not use where water is microbiologically unsafe or with water of unknown quality, except that systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.
33
Water filter
34
Performance Data Sheet For Filter Model 07134220
Using Replacement Cartridge 07134220
This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in
NSF/ANSI 42 and 53.
System tested and certified by NSF International in Model 07134220 against NSF/ANSI Standard 53 for the reduction of Cysts and
Turbidity and against Standard 42 for the reduction of Chlorine Taste and Odor; Nominal Particulate Class I.
Note that while the testing was performed under standard laboratory conditions, actual performance may vary.
To a capacity of 739.68 gallons (2800 liters).
Average Permissible Min. NSF
Concentration % Test
Turbidity 10.7 11 + 1 NTU 0.31 97.09 0.5 NTU 0.49 95.42 516456-05
Particulate
Class I Particle size:
> 0.5 to < 1 um 5700000
Chlorine taste and odor 1.9
At least 10,000 particles/ml
2.0 mg/L ± 10%
* Based on the use of Cryptosporium parvum oocysts
Application Guidelines/Water Supply Parameters
Water pressure 30- 120 psi (207 - 827 kPa)
Water temperature* 33°F - 100°F (0.6°C - 38°C)
Service flow 0.75 gpm (2.83 lpm)
30583
0.05
99.52
97.3
CAUTION: To avoid property damage due to water leakage, you MUST read and follow these operating instructions before installation and use of this product.
WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the
system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.
NSF is a registered trademark of NSF International.
CUNO is a trademark of 3M Company used under license.
© 2007 3M Company. All rights reserved.
> 85%
> 50%
69000
0.06
98.9
96.84
511079-03
511081-03
IMPORTANT: Must be installed and operated in accordance with application guidelines.
Failure to do so may void warranty.
Change filter at least every 6 months.
Flush new cartridge for 3 minutes.
For estimated costs of replacement elements please visit your local appliance dealer or parts distributor.
Lead free certificate
This product F 1411 SF (KIMSDF18US) is tested and certified by WQA against
ORD0902 for California "lead free" compliance.
Miele & Cie. KG
Carl-Miele-Straße 29
D-33332 Gütersloh
35
Frequently asked questions
With the aid of the following guide minor problems can be corrected without a service call.
Repairs should only be carried out by a qualified and trained person in strict accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage and may void the warranty.
Problems with temperature
Issue
The freezer does not get cold.
Possible fault
The machine is not turned on.
Solution
Check whether the appliance is turned on at the main switch. The temperature display must be lit up.
Check that the plug is correctly inserted in the power outlet.
The machine is not plugged in.
Check that the fuse has not tripped.
Reset the circuit breaker.
If the breaker trips again the appliance or the outlet may be defective. Contact Miele or a qualified electrician.
The temperature is set incorrectly.
Check the display.
The temperature in the freezer is too low.
Select a warmer temperature.
The SuperCool function is still on.
See "Selecting the correct temperature".
SuperCool automatically shuts off after 52 hours.
The freezer is too warm.
The door is not closed.
Check that the door has been closed properly.
A large amount of food is being frozen at the same time.
This makes the compressor run longer, causing the temperature to fall automatically.
The room temperature is lower than the ambient temperature for which the appliance is designed.
Raise the temperature of the room.
Operating the appliance in a room that is too cold will cause the cooling system to switch off for too long, causing the freezer section to become too warm.
36
Frequently asked questions
General problems
Issue Possible fault Solution
Water is flowing out of the appliance.
Close the shut-off valve immediately.
Check whether the water pipe in the appliance is defective.
Contact Miele Technical
Service.
Contact a plumber.
The door to the freezer section will not open.
Check whether the water pressure is too low.
Check whether the correct water valve has been installed.
This is not a fault.
The suction caused by opening and closing the door too many times in succession prevents it from opening.
Self-tapping valves and
3/16" (4.76 mm) saddle valves reduce the water pressure and can block the pipe.
Wait a few minutes, then try again. It should now open without force.
The compressor kicks on very frequently and for too long.
The ventilation slits are covered or dusty.
Clean with a vacuum or brush.
The door has been opened too frequently, or a large amount of unfrozen food has been put in at once for freezing.
Once the freezer gets down to the set temperature the compressor will turn off.
The door is not closed.
Check that the door has been closed properly.
The freezer runs continuously.
To save energy the compressor runs at a lower speed, but for longer when less cooling is required.
The temperature reading in the freezer shows -18°C, although a higher temperature is set.
This is not abnormal. When the ice maker is in use and the temperature of the room is above freezing the temperature automatically stays at -18°C to ensure proper functioning.
37
Frequently asked questions
Alarm / Indicator warnings
Issue Possible fault
The alarm is going off.
The appliance door(s) have been open for longer than 5 minutes.
The alarm is ringing and the "alarm" indicator is flashing.
The door is not closed.
A large amount of food is being frozen at the same time.
There has been a power failure.
The filter display is red.
This is a warning that the water filter needs to be changed soon.
The filter display is flashing red.
The water filter needs to be changed.
Solution
Close the door.
Once the alarm condition has been corrected, the alarm will turn off and the
"alarm" indicator will stop flashing.
Order replacement filters from Miele.
See "Exchanging the water filter".
38
Frequently asked questions
Problems with the ice maker
Issue
The ice cube maker will not switch on.
Possible fault
The appliance is not plugged in.
Solution
Check that the appliance is connected to the power supply.
The ice cube maker is not producing any ice cubes.
When the appliance is turned on for the very first time, it can take up to 10 hours for the first ice cubes to drop out of the ice cube maker and collect in the container.
The appliance is not turned on.
Check that the appliance is switched on.
The water supply line was not primed (purged of air) before the appliance was used for the first time.
Contact Miele.
Check if:
– the ice cube maker is switched on.
– the water supply line is open.
– there are ice cubes stuck together and blocking the exit.
– the ice cube container is in the right position.
– the freezer compartment temperature is too high.
– the water pressure is too low. The water pressure must be between 25 and
120 psi (1.72-8.25 bar).
See "Ice Cube Maker" and/or "Plumbing" for more information.
Check whether the correct water valve has been installed.
Self-tapping valves and
3
/
16
" (4.76 mm) saddle valves reduce the water pressure and can block the pipe.
39
Frequently asked questions
Problems with the ice maker
Issue
The ice cubes are small.
Possible fault
Other domestic appliances that use water are in operation.
Check whether the water filter needs changing.
Check the water pressure.
The water pressure must be between 25 and 120 psi
(1.72-8.25 bar).
Check whether the correct water valve has been installed.
Solution
Avoid using such items as a dishwasher, washing machine or shower at the same time.
See "Water filter" for more information.
Consult a plumber.
Self-tapping valves and
(4.76 mm) saddle valves
3
/
16
" reduce the water pressure and can block the pipe.
Use the ice maker more frequently.
The ice cubes have an unpleasant odor/flavor.
When ice is stored for an extended period it may absorb odors, which affects the taste.
Check if the ice cube container is dirty.
Unsealed packages in the freezer will transfer odor/flavor particles to the ice cubes.
Clean the container.
Check that food has been packed in airtight containers.
40
Frequently asked questions
Problems with the ice maker
Issue Possible fault
The ice maker is not producing enough ice or the ice cubes are misshapen.
Check the water pressure. The water pressure must be between 25 and 120 psi
(1.72-8.25 bar).
Ice is forming in the supply hose to the ice maker.
Check that the freezer temperature is too high.
Change the water filter.
Check the water pressure. The water pressure must be between 25 and 120 psi
(1.72-8.25 bar).
Check whether the freezer compartment temperature is too high.
Solution
Contact a plumber.
See "Selecting the correct temperature".
See "Water filter".
Contact a plumber.
See "Selecting the correct temperature".
41
After sales service
In the event of a fault which you cannot easily fix yourself, please contact the
Miele Technical Service Department at the address on the back of this booklet.
When contacting the Technical Service department, please quote the model and serial number of your appliance given on the data plate inside the appliance.
MieleCare
(USA only)
MieleCare, our Extended Service
Contract program; gives you the assurance of knowing that your appliance investment is covered by 5 years of worry-free ownership.
MieleCare is the only Extended Service
Contract in the industry that guarantees repairs by a Miele Authorized Service
Provider using genuine Miele parts.
Only genuine Miele parts installed by factory-trained professionals can guarantee the safety, reliability and longevity of your Miele appliance.
Please note that unless expressly approved in writing by the Miele Service department, Extended Service
Contracts offered by other providers for
Miele products will not be recognized by Miele. Our goal is to prevent unauthorized (and untrained) service personnel from working on your Miele products, possibly doing further damage to them, you and/or your home.
To learn more about MieleCare
Extended Service Contracts, please contact your appliance dealer or visit us online at: http://mieleusa.com/mielecare
42
Installation Instructions
Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information.
To prevent accidents and machine damage read these instructions before installation or use.
Caring for the environment
Disposal of packing materials
The cardboard box and packing materials are biodegradable and recyclable. Please recycle.
Ensure that any plastic wrappings, bags, etc., are disposed of safely and kept out of the reach of babies and young children. Danger of suffocation!
Disposal of an old appliance
Old appliances contain materials that can be recycled. Please contact your local recycling center about the possibility of recycling these materials.
Before discarding an old appliance, disconnect it from the electrical supply and cut off the power cord to prevent it from becoming a hazard.
44
Installation
Have the appliance installed by a qualified technician, according to the enclosed installation instructions.
Installation site
The appliance should be installed in a dry, well ventilated room.
WARNING
This appliance is top-heavy and must be secured to prevent it from tipping forward.
Keep the door closed until the appliance is completely installed and secured as per the installation instructions.
Empty weight of your machine:
F 1411 SF . . . . . . . . . . 359 lbs (163 kg)
Do not install the appliance:
- outdoors,
- in an environment with dripping water,
- in rooms which are at risk of frost.
The installation location should not be exposed to direct sunlight, nor near a heat source, such as an oven, radiator, etc.
The ambient temperature should not drop below 55°F (13°C) or rise above
110°F (43°C), otherwise malfunctions may occur.
If installation next to a heat source is unavoidable observe the following minimum distances from the heat source:
– 1
1
/
4
" (3 cm) from an electric cooktop or electric oven.
– 12" (30 cm) from a gas or oil cooktop, range or oven.
The following should also be taken into consideration:
– The electrical outlet must be easily accessible in case of an emergency,not concealed behind the appliance.
– The plug and cord must not touch the rear of the appliance as they could be damaged by vibrations from the appliance.
– Do not plug in other devices behind this appliance.
45
Installation
Important! When there is high humidity a build-up of condensation on the outer surfaces of the appliance can occur.This can cause the surfaces to corrode.To prevent this, it is advisable to install the appliance in a dry and/or an air-conditioned room with sufficient ventilation.Please ensure that doors close and seal properly after installation and that the appliance is installed in accordance with these installation instructions and and with the required ventilation openings.
– If the room is too cold, it will cause the cooling system in the appliance to remain off for too long.This can cause the temperature in the appliance to rise, resulting in damage.
46
Installation
Base
A fully loaded appliance is very heavy.
The load-bearing capacity of your floor must meet the following requirements.
The approx. weight of a fully loaded machine is:
F 1411 SF . . . . . . . . . . 626 lbs (284 kg)
To ensure that the appliance is installed securely and functions properly, the base must be flat, level and made of a hard, rigid material.
If in doubt, contact Miele.
Furniture/fixtures
The new appliance will be mounted securely to adjacent and overhead furniture/fixtures.
For this reason it is essential that all attachable furniture/fixtures are connected securely to the base or the wall by suitable means.
Ventilation
The air intake and outlet must not be blocked or covered in any way. They also need to be dusted/cleaned on a regular basis.
Installation niche
To ensure safe, trouble-free installation and the best possible cosmetic result, check to be sure that the installation space complies with the installation dimensions. See "Niche dimensions".
The side walls of the installation cavity must be plumb.
The minimum thickness of the side walls and the top wall must be
5
/
8
"
(16 mm).
The minimum thickness of the toe-kick panel must be ½" (13 mm). A thickness of
3
/
4
" (19 mm) is recommended.
47
Installation
Stainless steel panels
Stainless steel door panels and toe-kick covers are available from Miele.
Installation options
There are many different installation options. You are limited only by the design of the kitchen.
Side-by-side
This appliance can be installed
"side-by-side" with another fridge/freezer using a "Merging Kit".
The "Merging Kit" is available from
Miele.
The door hinge cannot be exchanged.
Contact Miele or your dealer for specific information about which combinations will work with your appliance.
Single column
The appliance can be installed at any preferred location in the kitchen.
However, be sure the door will open and close properly in the chosen location.
For instructions on how to attach the appliances and install the heating mat, please refer to the instructions included with the "Merging Kit", available from Miele.
Installation without a partition using the "Merging Kit"
If the appliances are installed directly next to each other (without a partition), they need to be attached together using the "Merging Kit".
48
Installation with partition using the
"Merging Kit"
The minimum thickness of the partition is 5 /
8
" (16 mm).
Installation
Side panels
If one side of the appliance is visible, a side panel must be used.
The side panel must be firmly secured to the wall, the floor and the overhead furniture/fixtures before the appliance is placed in the cavity.
The dimensions of the side panel are taken from the opposite wall of the installation space. During installation, ensure that the cavity is square and the measurements are correct.
If there is a partition with a thickness from
5
/
8
" (16 mm) to 6
5
/
16
" (160 mm) between the adjacent appliances, then each appliance should be individually installed within its own niche using the mounting accessories included.
The "Merging Kit" will also be needed.
The "Merging Kit" is available from
Miele.
Installation with partition without using the "Merging Kit"
If there is a partition with a thickness of more than 6 5 /
16
" (160 mm) between the adjacent appliances, then each appliance should be individually installed within its own niche using the mounting accessories included (the
"Merging Kit" is not necessary).
49
Dimensions
Niche dimensions
50
F 1411 SF
A
18 ½" (469.8 mm)
B
18" (457 mm)
Power supply and water connection
Dimensions
1. Power supply
2. Water connection
F 1411 SF
A
9" (229 mm)
Install a pressure limiting device and water hammer arrester for inlet water pressures exceeding 80 psi.(Refer to Uniform Plumbing Code, Sections 608.2
and 609.10) Never install or operate where inlet water pressure may exceed
120 psi.
51
Dimensions
Door dimensions (open 115°)
Miele recommends using the full door opening angle of 115° for this freezer.
F 1411 SF
A
20
11
/
16
"
(525 mm)
B
9
3
/
16
"
(234 mm)
52
Installing the appliance
Before you begin
Read these instructions completely and carefully.
Have the appliance installed by a qualified technician, according to the enclosed installation instructions.
– Open-ended wrench ½" (SW 13 mm)
– Box-end wrench
– 5 /
16
" (8 mm) hex nut driver
– Adhesive tape
– Multi-grip pliers
– Level
– Metal tape measure
– Square
To reduce the risk of injury or damage to the product, two people should be used for installation.
These installation instructions are intended for use by qualified installers.
In addition to these instructions, the appliance must be installed in accordance with all local codes. In the absence of a local code, the following should be used:
– In the USA, the National Electric
Code, ANSI/NFPA 70 - latest edition/State and Municipal codes and/or local codes.
– In Canada, the Canadian Electric code C22.1 - latest edition/Provincial and Municipal codes and/or local codes.
Other
– Stepladder
– Dolly, hand truck
– Wooden beam
(cross section min. 3" x 4"
[75 mm x 100 mm] as an alternative tilt protection, length depends on the width of the installation cavity)
– Wood screws in different sizes
– Edge protector(s)
Optional accessories
– "Merging Kit" for side-by-side installation
– RemoteVision module for wireless monitoring
Tools needed for installation
– Cutter with adjustable blade
– Cordless screwdriver T 20
– Torx screwdriver T 20
– Hammer drill for drilling holes in wall or floor
– Wood drills in different sizes
– Hammer
53
Installing the appliance
Aligning the housing unit
The housing unit must be carefully aligned using a spirit level before installing the appliance. The unit corners must be at right angles, as otherwise the furniture door will not align correctly with the 4 corners of the appliance.
– The side panels of the housing must be even.
– The housing unit panels must be at least 16 mm thick.
– The plinth facing must be at least
13 mm thick (or preferably 19 mm).
Check the installation niche
To ensure a safe, trouble-free installation and the best possible cosmetic result, check to be sure that the installation space complies with the installation requirements.
^ Check the base (see "Installation").
^ Check the dimensions of the cavity.
^ Check that the cavity is square.
^ Check the location of the power outlet.
^ Check the location of the water connection (see "Plumbing").
^ Check that all furniture parts in the vicinity of the appliance are securely connected to the wall.
^ Check that the adjacent furniture/fixtures do not collide with the open door.
Before installation
,
Caution - the appliance is very heavy. Use caution when unpacking and opening the door, danger of tipping.
^ To protect the base from damage during installation, attach a hard board, linoleum, etc., to the floor in front of the intended installation location.
^ Take the supplied accessories out of the protective packaging.
54
There are transportation safety devices inside the appliance to protect the shelves and storage compartments until installation is complete. Do not remove them, or parts may be damaged.
^ Check the appliance for damage in transit.
Do not install the appliance if it is visibly damaged. If in doubt, contact your dealer.
Installing the appliance
RemoteVision module installation
(optional accessory)
Always disconnect the appliance from the power supply when performing installation, maintenance or service work.
Install the RemoteVision module before placing the appliance in its installation niche.
Once connected the RemoteVision module will increase the energy consumption of the appliance.
The slot for the RemoteVision module is located in the lower area of the back of your appliance.
^ Loosen the bracket that holds the appliance to the pallet.
,
Caution! The appliance is no longer secured and may be unstable.
^ From the rear of the appliance carefully lift it from the pallet.
Once the appliance is on the ground it can be wheeled around.
^ Unscrew the screws a on the cover b and pull off the sticker c.
^ Remove the cover b.
55
Installing the appliance
^ Push the module into the slot until it locks into place.
^ Connect the appliance to the power supply and turn it on. After several seconds the indicator light e will come on.
The indicator light will display different colors one after the other; any control light at the end indicates that the module was correctly installed.
If the indicator light does not come on, installation of the module was unsuccessful. In that case, repeat the process. If that does not correct the problem, contact Miele.
^ Pull the antenna d straight out.
^ Guide the cover b over the antenna d and screw on the cover.
^ Angle the antenna d so that it faces to the right or left.
If necessary, disconnect the power supply and continue installing the appliance.
Preparing the installation niche
,
Keep the appliance door closed until it is securely fastened in the niche. Tipping hazard.
Because of the size and weight of the appliance, it is essential to ensure that the appliance cannot tip over once it has been mounted in the niche.
56
Installing the appliance
Mounting Accessories
The mounting accessories needed for installing the appliance into the niche are included in the packaging. Several plastic bags are included which are marked alphabetically.
The bag needed for each step will be marked with its respective letter.
Anti-tip brackets
The anti-tip brackets a keep the appliance safely secured in the installation niche b and prevent it from tipping.
Two anti-tip brackets are recommended for each appliance.For
side-by-side installations 4 brackets are recommended.
^ Position the anti-tip brackets a on the left and right in the installation niche so that there is no more than
3/8" (10 mm) of space between the brackets and the side walls.
^ Mark the drill holes in the anti-tip brackets on the back wall and on the ceiling of the installation niche.
^ Set the brackets aside - they will be needed again later.
Screws are supplied with the appliance for various applications/materials.
,
Risk of tipping
The installation niche must be securely attached to the wall behind it. This is the only way the appliance, which is later secured in the niche, can be prevented from tipping!
If the anti-tip brackets cannot be attached securely with the screws supplied, an alternative anti-tip device can be used.
Ensure that there are no electrical wires or plumbing in the area which the screws could penetrate - risk of injury and damage.
57
Installing the appliance
^ Now attach the installation niche to the wall.
The built-in cabinet must be secured to the wall behind it with several screws.
In a cabinet
with a back wall
In a cabinet without a back wall
^ screw the back wall of the cabinet in several places directly to the wall behind it.
For this, use suitable plugs/screws depending on the type of wall.
^ screw the cabinet to the wall behind it in several places using suitable mounting brackets.
For this, use suitable plugs/screws depending on the type of wall.
58
Installing the appliance
Securing an alternative anti-tip device
If the anti-tip brackets cannot be attached securely, an alternative anti-tip device can be used.
Ensure that there is no "give" between the appliance and the anti-tip device.
If possible, always screw the wooden beam to existing studs.
– Cut a wooden beam
(cross section min. 3" x 4"
[75 mm x 100 mm] to the required length).
– The length is equal to the width of the installation niche.
– If the installation niche is deeper than the appliance, select a beam with a larger cross section, or attach two beams.
– The beam must cover the appliance by at least 2" (50.8 mm).
^ Mark the installation height (lower edge of the beam) on the rear wall of the niche.
^ Select screws according to the thickness of the wooden beam.
Example: 3 ½" screw for 2x4 beam.
Determine the number of screws based on the niche width, to ensure that the beam will be attached securely.
^ Locate wall studs near the rear wall of the cavity and mark drill holes in the beam.
^ Pre-drill the wooden beam.
^ Attach the wooden beam to the rear wall of the niche.
Now prepare the water connection from the appliance to the main supply line
(see "Plumbing").
59
Installing the appliance
Sliding the appliance into the installation niche
If a side-by-side installation is desired, connect the two appliances together. See the Installation Manual included with the "Merging Kit".
^ Plug the appliance into the power outlet a.
The plug of the appliance should be easily accessible after installation.
If the plug is not accessible after the appliance has been installed, disconnection from the power supply should be completed via the circuit breaker.
^ Unscrew the plinth.
In the case of side-by-side installations, a separate outlet must be used for each appliance.
^ To prevent the power cord from becoming caught:
Tie a piece of string to the middle of the power cord and feed it forward under the appliance. When sliding the appliance in, pull the cable forward b.
^ Carefully slide the appliance into the space.
If resistance is felt when attempting to slide the appliance into the installation niche - for example, because the floor is uneven,
^ Turn the rear adjustable wheels slightly outward (see "Aligning the appliance"), then push the appliance in.
Be careful not to damage the water pipe or power cord attached to the floor.
^ Remove the edge protectors.
^ To protect the corners of the installation space, attach edge protectors where needed (not included).
60
Aligning the appliance
^ Align the appliance with the surrounding cabinets.
Installing the appliance
Important!
The height-adjustable feet can only be unscrewed as far as the 2 3/16"
(62 mm) mark on the base (max.
niche height of 85 3/16" (2164 mm).
The height-adjustable feet at the front and rear can all be adjusted from the front.
– Front feet:
Adjust with a rachet 5/16" (8 mm) c
– Rear feet:
Adjust with a (cordless) screwdriver and/or a rachet 5/16" (8 mm) for fine adjustment d
Important!
When unscrewing the height-adjustable feet, proceed gradually, alternating between left and right.
^ Unscrew the height-adjustable feet until the mark on the base has reached the indicated guide dimension 1 1/4" (32 mm). The guide dimension of 1 1/4" (32 mm) is related to a niche height of 84"
(2134 mm).
^ Align the appliance again using a level.
^ If using a wooden beam as an alternative anti-tip device, rotate the appliance all the way toward the wooden beam.
61
Installing the appliance
Attaching the appliance to the installation niche
^ Open the appliance doors.
^ Fasten the appliance on the left and right hand sides with the 3 (supplied) wood screws.
If there is a fairly large gap above the appliance, cut a wooden beam to fit exactly and place it in the gap.
Now connect the water supply to the appliance (see "Plumbing").
62
Installing the appliance
Attaching the toe-kick cover
The maximum height of the toe-kick cover is 4" (101 mm) from the top of the floor. Do not cover the ventilation slits in the plinth. Risk of damage to the appliance.
^ If required, cut the toe-kick cover to the required length and height.
^ Remove the foil from the adhesive strips.
^ Attach the toe-kick cover to the plinth.
^ Attach the plinth to the appliance.
^ Put the included cover plates in place.
63
Installing the appliance
Mounting the air separator
The air separator keeps the supply and exhaust air separate. This prevents warm exhaust air from flowing into the machine, optimizing the energy performance of the unit.
^ Position the air separator in the center of the appliance door.
^ If necessary, shorten the three parts of the air separator.
^ Insert the foam pieces back into the sides.
^ From below, screw the air separator firmly onto the door with the 2 screws.
64
Plumbing
All plumbing work should be carried out by a suitably qualified and competent person, in accordance with all applicable local and national regulations.
Disconnect the appliance from the electrical power supply before connecting it to the water supply.
Turn off the water supply before connecting the water lines to the ice cube maker.
The water quality must conform to country requirements for drinking water.
– The appliance is only suitable for connection to the cold water supply.
– The water pressure must be between
25 and 120 psi (1.72-8.25 bar).
– A separate shut-off valve must be installed, so that the water supply can be interrupted as needed.
– The maximum outer diameter of the water pipe (without fittings):
3 /
8
" (10 mm).
The shut-off valve for the water connection must not be located behind the appliance. It is recommended to place the shut-off valve directly next to the appliance
(base unit) or in another easily accessible location.
Do not use pipe extenders.
In the event that the piping has to be replaced only Original Miele Spare parts are suitable for use. Contact
Miele.
65
Plumbing
Preparing the water connection
For appliances with a hose guide
The connection to the household water supply must be installed before the appliance is installed.
^ Turn off the main water valve to prevent damage caused by leaking water.
^ Attach the connecting pipe to the shut-off valve, according to the instructions supplied by the manufacturer of the ice cube maker installation kit.
^ Install the connecting pipe. Always observe the indicated clearance dimensions to prevent damage to the connecting pipe when pushing in the appliance.
^ position the device in front of the niche and push the stainless steel tube through the hose guide at the back of the unit.
At this point the niche should be ready for the appliance to be pushed back into it (see "Installing the appliance").
^ You can now continue with the installation.
^ Secure the connecting pipe to the floor with adhesive tape.
^ You may now proceed to install the appliance. See "Installing the appliance".
66
Plumbing
Connecting the water supply
When connecting the water pipe to the solenoid valve of the appliance, follow the instructions supplied by the manufacturer of the ice cube maker installation kit.
When bending the water pipe, be sure not to kink it, otherwise there is a risk of leaks and water damage.
Use bending aids.
^ Push the union nut and seal onto the water pipe.
^ Push the end of the water pipe into the appliance connection and screw on the union nut, 3. First tighten by hand.
^ Then use an open-ended wrench to tighten the union nut. Do not over tighten.
^ Open the shut-off valve and the main water connection. Check for leaks at the connection for the shut-off valve and to the appliance.
^ Turn the appliance on.
After a maximum of 10 hours the first ice cubes will drop out of the ice cube maker and collect in the ice cube container.
^ Remove the cap from the appliance connection, 1.
^ Bend the water pipe to suit the location of the connection on the appliance, 2.
67
Electrical connection
,
Avoid the risk of electrical shock
- Plug into a grounded 3-prong outlet.
- Do not move the ground plug.
- Do not use an adapter.
- Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock.
Improper connection of the equipment grounding conductor may result in electric shock. If you are in any doubt as to whether the appliance has been properly grounded, have the appliance checked by a qualified electrician or service technician.
Installation, repairs and other work by unqualified persons could be dangerous.
Before installing the appliance, verify that the voltage, load and circuit rating information found on the data plate match the household electrical supply.
If there are any questions regarding the electrical connection of this appliance to the power supply, please consult a licensed electrician or call the Miele
Technical Service.
U1-800-999-1360
V1-800-565-6435
The appliance is supplied with a
UL-listed, 3-wire power cord and
NEMA 5-15 P plug ready for connection to a 120 V, 60 Hz supply.
The fuse rating is 15 amps.
The appliance requires a 3-wire receptacle.
The receptacle must be installed by a licensed electrician only.
In the case of side-by-side installations, a separate outlet must be used for each appliance. Ideally, the power outlet should be next to the appliance and easily accessible. Do not connect the appliance to the power supply by an extension cord. Extension cords do not guarantee the required safety of the appliance (danger of overheating).
If any changes are needed to the household wiring or power supply, this work must be performed by a qualified electrician.
68
RemoteVision (optional accessory)
Miele's RemoteVision Wi-Fi technology creates a 'virtual link' between your appliance and our monitoring center. If a fault occurs, Miele's client service center will be notified and contact you, or another trusted individual identified on your call roster, in order to gain access to your appliance to fix the problem.
For information on set-up and installation of the RemoteVision module see the "Installation" section of this manual.
Be sure your wireless system meets the following requirements
– A wireless router that supports an
IEEE 802.11b protocol
– Windows XP
® system, Mac ® or newer operating
OS X 10.3 or higher
– Cable or DSL modem
– Microsoft
®
Internet Explorer 6 or higher, Safari 2.0 or higher, Firefox
1.5 or higher
* Please note that each wireless router manufacturer supplies their own device drivers and setup programs. Due to the differences in manufacturers, exact router setup instructions are not included in this manual. Wording and instructions may vary.
69
RemoteVision (optional accessory)
Accessing the RemoteVision control panel
^ Touch the access button "p" so it turns yellow.
^ Note the position of the X button, but do not touch.
^ Touch the access button "p" again so it turns white.
Only the access button " p" is visible.
^ Place one finger on the position of the X button and hold (the X button will not be visible).
^ While holding down the X button, press the access button " p" once.
Keep holding the X button down until the following appears in the display
(approx. 5 seconds).
Access to the Custom settings mode is now active for approximately 10 seconds.
^ Tap the X button until ; appears in the display.
^ Touch the access button "p" to confirm.
See the table on the following page for a description of each setting in the display.
^ Use the Y or X buttons to select the
RemoteVision options.
The module has been connected to the network when display.
If
; # appears in the
; # does not appear, refer to the
"Network options" section of the
XKM 2000 Installation Instruction manual.
^ Press and hold the access button "p" for 2 seconds to confirm the change.
^ To return to the main menu, tap the X button until a solid
; - appears in the display.
^ Press the access button "p" to confirm.
^ Tap the X button until a ; appears in the display.
^ Touch the access button "p".
You have left the Custom settings mode.
When you are in the Custom settings mode the door alarm is turned off automatically. Once the door is closed it is reactivated.
70
RemoteVision (optional accessory)
MasterCool control panel options for RemoteVision
Status indicators Description of function
Flashing ; ~
Flashing ; ‡
Flashing ; |
Module booting phase
Not connected to network
Connection to network established, no IP address assigned
Solid ; #
Flashing ; <
Flashing ; =
Connected to network
In Ad-Hoc Mode, not connected
In Ad-Hoc Mode, connected
Selectable options
; -
; 2
; 3
; 4
Description of function
Back
Reboot the module
Reset to factory settings
Enter Ad-Hoc Mode
Note: If you cannot select any option (other than
; - "Back", the module has not been installed correctly.
71
Alteration rights reserved / 3
613
M.-Nr. 09 743 950 / 00
INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST
CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project