Miele Washer/Dryer 1119 User's Manual

Technical Information
Date: June 7, 2004
To: Technical Service
Subject: Washer/Dryer Stand
W1113, 1119, 1203, 1213, 1215
T1302, 1303, 1322C, 1323C, 1329C, 1403, 1405
Washer
Stand
Washer
Stand
Note: The washer/dryer stand is designed for use with washers and dryers only. Use for any other
purpose may result in damage to the machine or personal injury.
DO NOT USE OR PLACE A STACKED WASHER AND DRYER ON THIS STAND!
Carry out the following steps prior to installing the stands.
Drawer Removal
Pull the drawer out all the way. Lift upward to release and remove see Fig. 2.
Rear Panel Removal
Remove the rear panel screws (Torx T20) and remove the rear panel, see Fig. 3
Leveling
The stands must be leveled prior to installing the washer and dryer. Place the stands into their locations see
Fig4. Adjust the feet until the stands are level. Tighten the counter nuts.
Note: The studs for the washer are larger (17mm) than the studs for the dryer (13mm)
Washer Stand Installation
• Drain the unit, before laying it on its side.
• Remove the shipping struts
• Lay the washer on its right side. Be sure to lay the unit on a flat, soft underlay (i.e. carpet)
• Remove the washers feet
• Using the threaded studs and nuts provided (M10), screw 2 nuts midway onto each threaded stud.
• Screw the threaded studs (M 10) into the washer and tighten them see Fig. 5.
• Install a washer (10.2 x 32 x 2) on each threaded stud.
• Fit the stand onto the studs.
• Install a washer (10.5) on each threaded stud.
• Screw a nut (M 10) on each threaded stud and tighten.
• Stand the washer upright
• Install the washer stand rear panel using the 4 Torx screws provided see Fig. 3.
• Place the washer into its final position.
• Insert the 2 rubber bushings into the side holes of the washer stand. Install a washer and nut on each
and tighten the nut see Fig.6.
Dryer Stand Installation
• Drain the unit, before laying it on its side.
• Lay the dryer on its right side. Be sure to lay the unit on a flat, soft underlay (i.e. carpet)
• Remove the dryers feet
• Using the threaded studs and nuts provided (M8), screw 2 nuts midway onto each threaded stud.
• Screw the threaded studs (M 8) into the dryer and tighten them see Fig. 7.
• Install a washer (8.5 x 30 x 2) on each threaded stud.
• Fit the stand onto the studs.
• Install a washer (8.4) on each threaded stud.
• Screw a nut (M 8) on each threaded stud and tighten.
• Stand the dryer upright
• Install the dryer stand rear panel using the 4 Torx screws provided see Fig. 3.
• Place the dryer into its final position being sure to line up the studs of the rubber bushings with the holes
on the dryer stand.
• Once the stands are together and in their final positions install a washer and nut onto each stud and
tighten the nut see Fig.6.
• Install the caps into the open holes on the sides of the washer and dryer stand see Fig. 8.
Leveling
Once the washer and dryer (with stands) are in their locations. Adjust the feet until the stands are level. Tighten
the counter nuts.
Installing the Drawers
• Pull out the stand drawer rails as far as possible.
• Place the drawer on the rails and close the drawer, see Fig. 2.
• The drawer locks into position automatically when it is closed.
• Open the drawer as far as possible then close it to check that it functions correctly