MoistAir HD14070 User's Manual

QUARKSP6647 HD14070:SP6647
CAUTION:
.qxd
12/10/2009
3:39 PM
Page 1
READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLATION.
SAVE THIS OWNER’S MANUAL FOR FUTURE REFERENCE.
Model No.
HD14070
TM
HD14070
Evaporative Console
Humidifier Owner’s Manual
Part No. SP6647
12/09
Printed in U.S.A.
QUARKSP6647 HD14070:SP6647
.qxd
12/10/2009
3:39 PM
Page 2
GENERAL SAFETY INSTRUCTIONS
4. Keep the humidifier clean.
5. Do not put foreign objects inside the
humidifier.
6. Do not allow to be used as a toy. Close
attention is necessary when used by or
near children.
7. Never use your humidifier while any
part is missing or damaged in any
manner.
8. To reduce the risk of electrical hazard
or damage to humidifier, do not tilt, jolt
or tip humidifier while unit is running.
9. To reduce the risk of damage to
humidifier, unplug when not in use.
10. To reduce the risk of accidental
electrical shock, do not touch the cord
or controls with wet hands.
11. To reduce the risk of fire, do not use
near an open flame such as a candle or
other flame source.
12. Note the warning label shown below.
Safety Signal Words
DANGER: means if the safety information is
not followed someone will be seriously
injured or killed.
WARNING: means if the safety information
is not followed someone could be seriously
injured or killed.
CAUTION: means if the safety information
is not followed someone may be injured.
1. To reduce the risk of fire or shock
hazard, plug humidifier directly into a
120V, A.C. electrical outlet. Do not use
extension cords.
2. Keep the electric cord out of traffic areas.
To reduce the risk of fire hazard, never
put the electric cord under rugs, near
heat registers, radiators, stoves or
heaters.
3. Always unplug the humidifier before
moving it, removing the fan assembly
section, before cleaning, or whenever
the humidifier is not in service.
WARNING: To reduce risk of fire, electric
shock, or injury always unplug before
servicing or cleaning.
2
QUARKSP6647 HD14070:SP6647
.qxd
12/10/2009
3:39 PM
Page 3
Know Your Humidifier
Description
HD14070
* Output/24 hrs
Capacity of Bottle
* Sq. Ft. Coverage
Fan Speeds
Auto Fan Speed
Replacement Filter
Refill Indicator
Auto Shut Off
Auto Humidistat
Controls
Control Lock
Casters
ETL Listed
Volts
Hertz
Amps
Watts
14 Gallons/53 Litres
2-3/8 Gallons/9 Litres
2900
3
Yes
Set of 4 (HDC12)
Yes
Yes
Yes
Electronic (Push Button)
Yes
Yes (4)
Yes
120 A.C.
60
2.88
165
* Based on an area with average insulation and an 8’ ceiling height
ANSI/AHAM HU-1-1997. SEC. 8.1, results may vary.
3
QUARKSP6647 HD14070:SP6647
.qxd
12/10/2009
3:39 PM
Page 4
How Your Humidifier Works
Your new MoistAIR humidifier is designed to
satisfy home humidity requirements through the
principle of evaporation of water into the air.
After water is added to the bottle, the filters begin
to soak up the water and become totally saturated
in approxi-mately 30 minutes. Air is drawn in from
the rear of the humidifier and through the filters by
means of circulation fans. As air passes through
the filters, moisture is absorbed into the air and
then released in the form of vapor. No water
droplets will enter the home. All evaporation into
the air takes place in the humidifier, which means
that the residue left by evaporating water is not
passed into the home, but remains in the filter.
CAUTION: To reduce the risk of injury, fire or
damage to humidifier, use only cleaners
specifically recommended for humidifiers.
Never use flammable, combustible or
poisonous materials to clean your humidifier.
To reduce the risk of scalds and damage to
humidifier, never put hot water in humidifier.
CAUTION: Use only EPA Registered
Bacteriostat. Under no circumstances should
you use water treatment products designed
for Roto belt or Ultrasonic humidifiers.
Assembly
Your new MoistAIR humidifier is completely
assembled for you to use. Remove the bag pack
containing two plastic caster pads from top of
humidifier and retain for future use if required. See
the following Step 1 for instructions.
Remove the packaging material from inside your
humidifier and follow the instructions of this
operator’s manual for proper usage. The
packaging material is located under the fan
assembly. Remove the packaging material and
discard.
4
QUARKSP6647 HD14070:SP6647
.qxd
12/10/2009
3:39 PM
Page 5
Location Instructions
Moist air (humidity) produced will disperse into the
whole house, but area closest to the unit will have
the highest humidity. If the unit is positioned close
to a window, condensation may form on the
window pane. If this is not appropriate the unit
should be repositioned in another location.
WARNING: For your own safety, do not use
humidifier if any parts are damaged or
missing.
Step 1:
Place humidifier on a flat level surface in an area
of your house where humidity is needed most, or
in an area which would likely result in moist air
being circulated throughout the house, such as
near a cold air return.
Placing the unit level is very important if the
humidifier is located on carpeting.
NOTE: The humidifier contains water bottles. The
weight of the bottles in the front of the cabinet
may cause the front casters to sink deeper into
the carpet. If this happens, the water level will be
higher towards the front of the humidifier, and
lower towards the back. The water level float
(located at the rear of the cabinet) may not sense
the water so the flashing “F” will be displayed and
the unit will not energize. If this happens, the unit
will need to be leveled in order for the humidifier to
be energized. To level the humidifier when located
on carpet, place the included caster pads under
the front two casters of the humidifier only.
NOTE: Due to release of cool, moist air from
humidifier, it is best to direct air away from home
thermostat and hot air registers. It is best to
position humidifier next to an inside wall. Hot air
registers and cold air from outside walls can affect
the efficiencies of the controls. Unit should not be
placed where warm air from a hot air register
blows directly on unit.
Step 2:
The humidifier should be positioned
with the back (cord exit side), at least
5 centimeters away from the wall.
Air needs to enter through the louvers in the rear
panel in order for the humidifier to operate at peak
efficiency.
Operating Tips for Best Performance
4. Perform regular cleaning as instructed in
“Cleaning and Maintenance” section of this
manual.
5. Replace the evaporative wicking filters at least
once per humidification season or more
depending on water conditions in your area.
1. Position the humidifier at least 2 inches (5 cm)
from any wall and away from any heat
registers.
2. Do not restrict airflow from entering or exiting
the humidifier.
3. Use only EPA registered bacteriostat to retard
bacteria growth that may cause odors and may
be harmful to your health.
5
QUARKSP6647 HD14070:SP6647
.qxd
12/10/2009
3:39 PM
Page 6
Electrical Hook-Up
If the plug does not fit fully in the outlet, reverse
plug. If it still does not fit, contact a qualified
electrician to install the proper outlet. Do not
change the plug in any way.
Locate nearest 120V A.C. wall socket in the
location desired, preferably on inside wall. With
the humidifier in the desired location, route the
electrical cord safely so no one will trip or upset
the humidifier. Plug in the electrical cord.
WARNING: To reduce the risk of fire
or shock hazard, humidifier should
be plugged into a 120V A.C. outlet.
Do not use extension cords.
To reduce the risk of electrical shock, this
humidifier has a polarized plug (one blade is wider
than the other). This plug will fit in a polarized
outlet only one way.
Water Fill
WARNING: To reduce the risk of shock,
always unplug humidifier before cleaning or
servicing.
WARNING: To reduce the risk of fire or shock
hazard, do not pour or spill water into control
or motor area.
If controls get wet, let them dry completely
and have unit checked by authorized service
personnel before plugging in.
This humidifier is designed for use with the two
water bottles that are located under the pivoting
lid.
Open the pivoting lid of the humidifier. Remove the
water bottles by lifting them straight up and out of
the cabinet.
Notice the water bottles are designed as right and
left hand units. Position them in the correct
location so the humidifier can function properly.
The water bottles should rest in the front of the
cabinet. Each “Side-Fill Cap” must be facing the
rear of the unit.
6
QUARKSP6647 HD14070:SP6647
.qxd
12/10/2009
Water Fill (continued)
Each water bottle is designed with a “Side-Fill
Cap” that is easily removable. Remove the “SideFill Cap” on the side of the water bottle by twisting
counterclockwise.
Place the opening of the water bottle under a
water faucet (the bottle should fit under a four-inch
clearance faucet). Fill with recommended mixture
of cold water and Bacteriostat (if necessary) only.
Solid debris could make the valve leak.
Install the “Side-Fill Cap” by twisting clockwise.
Hand tighten only.
Check for possible leaks by performing the
following:
1. Grasp bottle handle and hold the bottle upright
over a sink.
2. Press up on the valve cap plunger for about
one second to let out a little water.
3. Release the plunger.
4. Listen for air bubbles Look for leaks around the
“Side-Fill Cap”.
5. If you hear air bubbles or see leaks, retighten
the “Side-Fill Cap” and repeat Steps 1-4.
Wipe off excess water from the bottle.
Position the water bottle back into the unit by
grasping the water bottle handle and lower it into
the cabinet until the bottle sits on pads at bottom
of cabinet. The “Side-Fill Cap” must be facing the
rear of the cabinet. When positioned properly, the
plunger will open and water will flow into the
cabinet. The water level will automatically remain
at approximately 1/2” until the bottles are empty.
Allow the filter to saturate for 30 minutes before
operation.
7
3:39 PM
Page 7
QUARKSP6647 HD14070:SP6647
.qxd
12/10/2009
3:39 PM
Page 8
Operating the Controls
Where you set your desired humidity levels
depends on your personal comfort level, outside
temperature and inside temperature. A starting set
point of 30% - 40% ROOM humidity is
recommended but there may be conditions that
require a different setting.
IMPORTANT: Water damage may result if
condensation starts to form on windows or
walls. Humidity SET point should be lowered
until condensation no longer forms. We
recommend room humidity levels do not
exceed 50%.
When Outdoor
Temperature is:
-10° F
2° F
10° F
20° F *
Speed Button
This humidifier is equipped with a
3-speed fan control. Initially depressing the speed
button will display the current speed setting. Each
push of the speed button advances the mode
through the settings of (HIGH) F3, (MEDIUM) F2,
and (Ultra Quiet) F1.
The selected setting is displayed on the digital
readout. The higher the setting, the faster water is
evaporated and released into the air. F1 (Ultra
Quiet) is the quietest setting and is provided for
conditions that do not require a rapid evaporation
rate.
Recommended Indoor
Relative Humidity is:
-24° C
-18° C
-12° C
-6° C *
20%
25%
30%
35%
* and above
To Operate the Controls
Digital Display
Press the power/speed button once to turn the unit
on*
. Initially there is a slight delay while the
electronics calibrate. Two bars (- -) appear during
this time. Once calibration is complete a ROOM
humidity reading between 20% - 95% will be
displayed. A flashing 20 display indicates that the
room humidity is less than 20%.
NOTE: The default settings at initial startup are
(Ultra Quiet) F1 fan speed and 65% SET humidity.
After desired settings are selected by the user,
they remain as long as the unit remains plugged in
and there is no power interruption. If the unit is
unplugged the original default settings are
employed.
Humidity Control
This button allows you to adjust the humidity to suit
your needs. This humidifier will automatically cycle
on and off as required to maintain the selected
setting. The readout displays both actual (ROOM)
and desired (SET) humidity percentage (%) settings
when humidity control button is pressed. The
ROOM readout has a range of 20% to 95%. If the
room humidity level is equal to or less than 20% the
display will show a flashing 20.
* Humidifier fan should operate at initial start up. If it
does not, refer to, “Fan not operating (digital display is
illuminated)” in the “Trouble Shooting” section on page
14.
8
QUARKSP6647 HD14070:SP6647
.qxd
12/10/2009
3:39 PM
Page 9
Operating the Controls (continued)
The SET readout has a range of 25% to 65% and
is adjusted in increments of 5%. Initially
depressing the humidity button will display the
current humidity setting. Each additional press of
the button increases the setting by 5%. A SET
point of 65% operates the humidifier continuously
regardless of the ROOM reading. The humidistat
that senses the readings is located on the power
cord. Insure that this humidistat is free from
obstruction.
Using Your Humidifier
To do this, simply slide the float retainer located at
the back of the humidifier cabinet to the top
position of the slot it is located in. This will hold the
float in an upward position and the fan will run until
you turn the power off.
Refill Display Function
For maximum run time both bottles should be
filled. When both bottles are empty the display
alternates the room humidity reading and “F”
(FILL), informing additional water is required.
NOTE: Be sure to position float retainer to the
normal operating mode (lowest position in slot) for
normal humidifier operation.
Below is a diagram of the slot the float retainer is
located in, at the back of the cabinet.
Manual Dry Out
At the end of the humidification season or if you do
not plan to run the humidifier for one week or
more, a manual dry out mechanism is provided to
completely dry out the humidifier cabinet.
9
QUARKSP6647 HD14070:SP6647
.qxd
12/10/2009
3:39 PM
Page 10
Using Your Humidifier (continued)
Check Filter Indicator
The ability of any humidifier to efficiently supply
humidity output relies heavily on the condition of the
filter. As the filter loads with impurities it gradually
loses its wicking capability. When this happens,
moisture output is reduced and the humidifier has to
work longer to satisfy the selected setting. This
humidifier has a check filter reminder timed to
appear after 720 hours of motor operation. When the
display shows an alternating “CF” and “room
humidity” setting at 5 second intervals it is a
reminder to check the filter condition.
NOTE: Some areas have high water mineral content
causing the need for more frequent filter changes.
Refer to “Replacement and Care of Filter” on page
11. If a build-up of deposits or severe discoloration is
evident replace the filter to restore maximum
efficiency.
Humidistat
The humidistat located on the power cord senses
the percentage of humidity in the air. It causes the
humidifier to cycle on and off to maintain the
selected humidity SET point. The fan will turn on if
the “ROOM” reading falls 3% below the SET point
and will continue to run the humidifier until a
reading of 1% above the SET point is achieved.
The fan will turn off until the ROOM reading falls
3% below the SET point again.
NOTE: Be sure humidistat, which is located on
the power cord, is free from obstructions and is
away from any hot air source.
10
QUARKSP6647 HD14070:SP6647
.qxd
12/10/2009
3:39 PM
Page 11
Replacement and Care of Filters
WARNING: To reduce the risk of shock or
injury from moving parts, always unplug
humidifier before removing or replacing any
parts.
CAUTION: To help retard bacteria growth and
keep maximum efficiency, the filter should be
replaced at least once per season, or more
often under hard water conditions. Use
MoistAIR HDC12 recommended replacement
filter.
The filters may be rinsed periodically in clear water
only. Take care not to damage paper. To replace
evaporative wicking filters in your humidifier, follow
these instructions.
1. Unplug humidifier before removing the filters.
We recommend moving the humidifier to an
area where floor coverings are not susceptible
to water damage, i.e. kitchen or bath areas.
2. Open the pivoting lid and remove water bottles
and set aside. Grasp the fan assembly front
center and rear center. Lift off and set aside on
a clean flat surface. The filter housings are
now accessible.
3. Lift filter housing out of cabinet and place
where you may work on them comfortably.
With a soft, absorbent cloth remove any
remaining water or loose mineral deposits not
trapped in the filter from the humidifier cabinet.
4. To open filter housing for easy access to filters:
a. Deflect the two spring tabs on top of filter
housing. Lift top cover off of the filter
housing and set aside.
c. Install new filters in the filter housing track
with the glue beads of the wicking pad to
the inside of the filter housing.
b. Remove the two filters and dispose of
properly. Clean internal parts of humidifier
per the “Cleaning and Maintenance” section
(page 12) of your operator’s manual.
d. Return the top cover of the filter housing by
installing cover over the fixed tabs on the
rear of the lower filter housing and pivoting
the cover down over the top of the filters.
Snap the cover over the two spring tabs.
11
QUARKSP6647 HD14070:SP6647
.qxd
12/10/2009
3:39 PM
Page 12
Replacement and Care of Filters (con’t)
e. Replace the filter housing in the cabinet.
NOTE: There is a front and back orientation. To
position the filter housings correctly:
• Be sure that the spring tabs of filter
housings are towards front of cabinet.
• Align the lower portion of the filter assembly
over the six ribs located at the bottom rear
of the humidifier cabinet.
f. Position fan assembly onto the cabinet.
Make sure the fan venturi (lowest cylinder
section below the fan) is placed inside the
filter housing.
g. Replace water bottles.
h. Close the pivoting lid.
i. The unit is ready for use or to be stored
away for next season.
Cleaning and Maintenance
NOTE: If it is necessary to use approved
bacteriostat, follow directions correctly.
The bottles of the whole house humidifier will hold
2-3/8 gallons/9 litres of water each.
Step 1:
To make cleaning easier, the humidifier cabinet
should be empty and completely dried out. To
accomplish this, use the following method:
a. On the back side of the humidifier cabinet, find
the float retainer. In normal operating mode,
the retainer will be positioned in the bottom of
the slot in the cabinet. Push the retainer up to
the top slot position in the cabinet until it locks
in place. (See “Manual Dryout” section on page
9.)
b. Allow the humidifier to run until there is no
water left in the cabinet.
c. Unplug humidifier.
WARNING: To reduce the risk of injury, fire or
damage to humidifier, use only cleaners
specifically recommended for humidifiers. Never
use flammable, combustible or poisonous
materials to clean your humidifier. To reduce the
risk of scalds and damage to humidifier, never put
hot water in humidifier.
CAUTION: Local water purity varies from area to
area and under certain conditions water impurities
and airborne bacteria may promote the growth of
micro-organisms in the reservoir of the humidifier.
To retard bacteria growth that may cause odors
and be harmful to your health, use only MoistAIR
replacement filters. We also recommend using
EPA approved bacteriostat and humidifier cleaner.
12
QUARKSP6647 HD14070:SP6647
.qxd
12/10/2009
3:39 PM
Page 13
Cleaning and Maintenance (cont’d.)
Bi-Weekly Maintenance
Removing Scale
WARNING: To reduce the risk of shock, always
unplug humidifier before cleaning or servicing. If
humidifier is not unplugged, fan could start after
housing is removed.
1. Fill the reservoir with water and add one 8
oz. (236 ml) cup of undiluted white vinegar.
Let solution stay for 20 minutes.
2. Clean all interior surfaces with soft brush.
Dampen soft cloth with undiluted white
vinegar and wipe out reservoir to remove
scale.
3. Rinse thoroughly with clean warm water to
remove scale and cleaning solution before
disinfecting the reservoir.
Step 2:
To Remove Parts
a. Open the pivoting lid and remove water bottles
nd set aside. Grasp the fan assembly front
center and rear center. Lift off and set aside on
a clean flat surface. The filter housings are
now accessible.
b. Before removing the internal parts of the
humidifier cabinet, we recommend moving the
humidifier to an area where floor covers are
not susceptible to water damage, i.e.; kitchen
or bath area. Lift the filter housing assemblies
out of the cabinet and set to the side.
c. Remove the water level float from the
humidifier cabinet by pinching the float retainer
to release it from the cabinet. The cabinet
should be empty before cleaning. The cabinet
consists of the lower areas of the humidifier
where the filters are during normal operation
time.
d. Empty cabinet of any remaining water.
e. Proceed to “Bi-Weekly Maintenance” or “End of
Season Maintenance”.
f. Remove old filters and dispose of properly as
described on pages 11-12.
Disinfecting Humidifier Cabinet and
Water Bottles
1. Fill humidifier cabinet with
1 teaspoon (5 ml) chlorine bleach in 1
gallon (3.8 litres) of water.
Let solution stay for 20 minutes, carefully
swishing every few minutes. Wet all
surfaces normally exposed to water.
2. Empty humidifier cabinet after 20 minutes.
Rinse with water until bleach smell is gone.
Allow unit to dry out completely.
3. Water bottles should be cleaned in the
same manner.
End of Season Maintenance
1. Follow “Bi-Weekly Maintenance” instructions at
end of humidification season.
2. Remove and throw away filters.
3. Let humidifier dry completely before
storing. Do not store with water inside cabinet
or water bottles.
4. Store in cool, dry location.
5. Install a new filters in clean humidifier before
next season begins.
6. “Bi-Weekly Maintenance” procedure is also
recommended if you do not plan to run the
humidifier for one week or more.
Step 3:
Install new filters (purchase the correct evaporative
wicking filter pads HDC12 for your humidifier) into
the location where the old filters were positioned.
Install the filter housings with the new filters into
the correct location. Reinstall the water level float.
NOTE: Float retainer should be positioned in
normal operating mode. Assure that it is positioned
in the bottom of the slot in the back of the cabinet
(See page 9 for diagram of slot).
Position the fan assembly on top of the cabinet
and return the humidifier to the desired location for
use.
Refill humidifier bottles with fresh cool water and
return them to the cabinet. Plug the unit into a 120
volt A.C. power outlet and set the controls per the
“Operating Humidifier Controls” section (page 8) of
this manual.
13
QUARKSP6647 HD14070:SP6647
.qxd
12/10/2009
3:39 PM
Page 14
Troubleshooting
Probable Cause
Remedy
• No Power.
• Power button has not been depressed.
• Check 120 volt power source.
• Press power button once to turn on.
Fan not operating (digital
display is illuminated).
• ROOM humidity level is not 3% or more
below SET humidity level.
• Reservoir is empty.
• Raise SET humidity level if desired.
• Increase fan speed.
• Fill humidifier with water.
Fan running continuously,
unit will not shut off.
• Free float from obstruction.
• Float is obstructed.
• A SET humidity percentage
• SET humidity level is 65%.
of 65% operates fan
• ROOM humidity level has not reached 1%
continuously. Adjust SET
or more above SET humidity level.
level between 25% - 60%.
• Continue to run until desired humidity
level is achieved. This may take up to 48
hours initially.
Poor evaporation of water.
• Check filter message “CF” is flashing.
• Mineral buildup on filter.
Neither bottle emptying.
• Bottle cap plunger missing post in bottom • Check orientation of bottles.
Reposition so that bottle cap plunger
of cabinet.
(stem) is depressed by post in bottom of
• Dirty filters.
cabinet.
• Change to fresh new filters
(HDC12).
Bottles continues to empty.
• Air is entering water bottle.
• Check “Side-Fill Caps” and valve
assembly caps to ensure tightness.
• Check for leak in water bottle.
• Ensure gaskets for “Side-Fill Caps” are in
place.
Left bottle not emptying.
• Right bottle contains water.
The humidifier is designed so that right
bottle empties first.
Refill display “F” is on before
bottles are empty.
• Unit is not set up on a level surface.
(Float will not sense water at the front of
the cabinet.)
• Position unit level. (Some carpet padding
may allow unit to sit lower in the front than
rear with the additional weight of water
bottles in the front of the cabinet. Install
caster pads under front casters (see page
5).
Display blinks or fan moves slightly when
humidifier is plugged in.
• Normal.
• No action required.
Trouble
Digital display not illuminated.
• Change to a fresh new filter.
NOTE: Local water purity varies from area
to area.
Alternating “F” and room humidity displayed. • Reservoir is empty.
• Fill humidifier with water.
Alternating “CF” and room humidity
displayed.
• Replace filter.
• Filter may be dirty.
CAUTION: Use only EPA Registered Bacteriostat.
Use of other water treatment products may damage the filter elements. Under no circumstances should you use water treatment products
designed for Roto belt or Ultrasonic humidifiers.
14
QUARKSP6647 HD14070:SP6647
.qxd
12/10/2009
3:39 PM
Page 15
Repair Parts
Parts List for MoistAIR® Humidifier
Model No. HD14070
MD
15
QUARKSP6647 HD14070:SP6647
.qxd
12/10/2009
3:39 PM
Page 16
Repair Parts
Parts List for MoistAIR® Humidifier
Model No. HD14070
MD
Always order by part number - Not by key number
Key
No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
—
Part No.
Description
828741-2
Lid, Stationary
828855-2
Lid, Pivoting
831680-1
Control Assembly
824690
“Side-Fill Cap”
828192
Bottle, Left (Includes Key Nos. 4 & 7)
828726
Bottle, Right (Includes Key Nos. 4 & 7)
509229-1
Cap, Valve Assembly
828199-10
Cabinet
823726
Rail, Kick
STD601107 * Screw, Pan Hd. Ty “AB” #10 x 3/4
828515
Caster, Twin Wheel
830560-1
Support, Filter Lower
† Filter, Evaporative
HDC12
828534
Support, Motor
828115-1
Motor
822406-1
Fan
828197
Support, Upper Filter
824101
Retainer, Float
828200-3
Float, Water Level
828920
Pad, Caster (Two)
SP6647
Operator’s Manual (not illustrated)
87
NOTE: Any attempt to repair the control assembly or motor may create a
hazard unless repair is done by a qualified service technician.
* Standard Hardware Item - May be purchased locally
† Stock item - Purchase locally or call numbers below
To order parts call:
USA:1-800-547-3888
Canada: 1-888-744-4687
16
QUARKSP6647 HD14070:SP6647
.qxd
12/10/2009
3:39 PM
Page 17
Warranty
Moist AIR® PRODUCTS
HUMIDIFIER WARRANTY POLICY
EFFECTIVE APRIL 1, 2008
SALES RECEIPT REQUIRED AS PROOF OF PURCHASE
FOR ALL WARRANTY CLAIMS.
This product is warranted against defects in workmanship and materials for one year
from the date of sale except for motors, which are warranted for two years. This warranty
does not apply to filters or wicks which are customer replaceable parts.
This warranty applies only to the original purchaser of the product when it is purchased
from a reputable retailer/dealer.
This warranty does not apply to damage from accident, misuse, alterations,
unauthorized repairs, unauthorized use, mishandling, unreasonable use, abuse,
including failure to perform reasonable maintenance, normal wear and tear, nor where
the connected voltage is more than 5% above the nameplate voltage, nor to the
equipment or products being improperly installed or wired or maintained in violation of
this Owner’s Manual.
Alterations include the substitution of name brand components including, but not limited
to wicks and bacteria treatment.
THIS PRODUCT IS NOT INTENDED FOR COMMERCIAL USE. THIS IS THE SOLE
AND EXCLUSIVE WARRANTY GIVEN BY MANUFACTURER WITH RESPECT TO
THE PRODUCTS AND, TO THE MAXIMUM EXTENT PERMITTED BY LAW, IS IN LIEU
OF AND EXCLUDES ALL OTHER WARRANTIES AND CONDITIONS, EXPRESS OR
IMPLIED, ARISING BY OPERATION OF LAW OR OTHERWISE. INCLUDING
WITHOUT LIMITATION, MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
PURPOSE.
No employee, agent, dealer or other person is authorized to give any warranties or
conditions on behalf of the manufacturer. The customer shall be responsible for all costs
incurred in the removal or reinstallation and shipping of the product for repairs.
Within the limitations of this warranty, purchaser with inoperative units should contact
customer service @ 800-547-3888 for paperwork and instructions on the return of the
unit for repair. A copy of the sales receipt is required before authorization to return a
unit for repair is approved. The manufacturer will repair or replace the product, at its
discretion, at no charge to the customer with return freight paid by the manufacturer. It
is agreed that such repair or replacement is the exclusive remedy available from the
manufacturer and that TO THE MAXIMUM EXTENT PERMITTED BY LAW, THE
MANUFACTURER IS NOT RESPONSIBLE FOR DAMAGES OF ANY KIND,
INCLUDING INCIDENTAL AND CONSEQUENTIAL DAMAGE OR LOSS OF PROFITS
OR REVENUES.
This warranty will be null & void if purchaser attempts to repair or replace any parts
which are mechanical or electrical.
The warranty gives the customer specific legal rights, and the customer may also have
other rights which vary from province to province, or state to state.
17
QUARKSP6647 HD14070:SP6647
.qxd
12/10/2009
3:39 PM
Page 18
FOR TECHNICAL HELP, CALL
(800) 547-3888 FROM USA OR (888) 744-4687 FROM CANADA
(Please have complete model number)
®
MD
Essick Air Products
For more information about MoistAIR® humidifiers, visit our website at
www.moistair.com
MD
c 2009
Part No. SP6647
Form No. SP6647-1
Printed in U.S.A
12/09
Download PDF
Similar pages
Topcom Ultrasonic Humidifier 1801
Steba LB 6 CUBE
Johnson Controls 4000 User's Manual
Philips HU4706
Essick Air EP9 500 User's Manual
Argoclima STEAMMY
FIELD CONTROLS SC100 User's Manual