MyPBX U510 Installation Guide
MyPBX U510 Installation Guide
Version: V1.1
Yeastar Technology Co., Ltd
Date: 9th, Aug, 2013
http://www.yeastar.com
1/17
MyPBX U510 Installation Guide
Contents
1. PREPARATION BEFORE INSTALLATION ............................................. 4
2. HARDWARE SPECIFICATIONS ........................................................ 5
2.1 OVERVIEW ........................................................................................................................................................ 5
2.2 LED INDICATORS AND PORTS ................................................................................................................................. 5
2.3 SPECIFICATIONS AND OPERATING ENVIRONMENT ........................................................................................................ 7
3. MYPBX U510 INSTALLATION ......................................................... 8
3.1 PLACEMENT INSTRUCTIONS ................................................................................................................................... 8
3.2 INSTALLATION INSTRUCTIONS ................................................................................................................................. 8
3.2.1 Connection of Ethernet Ports ................................................................................................................... 8
3.2.2 Connection of E1/T1/FXO/GSM/UMTS/BRI ports ..................................................................................... 9
3.2.3 Connection of FXS ports......................................................................................................................... 12
3.2.4 Power Connection ................................................................................................................................. 12
3.2.5 Overall Flow Chart................................................................................................................................. 12
4. MYPBX U510 BASIC CONFIGURATIONS .......................................... 13
4.1 FACTORY DEFAULTS ........................................................................................................................................... 13
4.2 LOGGING IN THE WEB CONFIGURATION PANEL ......................................................................................................... 13
4.3 NETWORK SETTINGS .......................................................................................................................................... 15
4.4 EXTENSIONS SETUP AND MANAGEMENT ................................................................................................................. 15
4.5 CONFIGURING TERMINALS .................................................................................................................................. 15
4.6 MAKING/RECEIVING CALLS ................................................................................................................................. 16
4.7 RESET TO FACTORY DEFAULTS ............................................................................................................................... 16
5. CONCLUSION ........................................................................ 17
http://www.yeastar.com
2/17
MyPBX U510 Installation Guide
About MyPBX U510
MyPBX U510 is a standalone embedded hybrid PBX with one embedded E1/T1/J1 port. It is specially designed
for businesses and offices up to 300 users which are characterized by flexible compatibility with PSTN/ISDN
BRI lines, GSM/UMTS network and IP lines with powerful functionality. It enables the company to benefit
from the latest VoIP technology and traditional reliability at the same time.
MyPBX U510’s scalability is impressive too. With the deployment of MyPBX U510, the company will no more
worry about the high expansion costs and the waste of their previous investment. The modular technology
enables the company to freely choose the combination of FXO, FXS, BRI, GSM, and UMTS modules as
required, and just add on the type of modules that are needed for future expansion. For example, if 2 more
PSTN lines are required, they needn’t bother to buy a new PBX. Just add another O2 module (2 FXO ports) is
OK. Also, the new user account is free of charge. The company is not going to pay any license fees for new
employees.
Moreover, MyPBX U510 has perfect interoperability with mainstream IP Phone brands such as Yealink, Snom,
Grandstream, Aastra, Polycom and Cisco. Auto provisioning of Yealink, Snom, Cisco, Aastra and Polycom IP
phones would greatly save time on configurations when there is bulk extensions to register.
Besides, customers from different countries will all feel comfortable while using MyPBX U510. Because they
are able to select their local language for Web GUI and Voice Prompt. Furthermore, it is renowned for its
user-friendly web configuration panel which is easy accessible and self-evident making configuration a
trouble-free job.
This Guide explains how to install MyPBX U510, how to configure MyPBX U510 via web interface, how to add
extensions, and make/receive calls via trunks.
http://www.yeastar.com
3/17
MyPBX U510 Installation Guide
1. Preparation before Installation
Please make sure the following devices are available before installation:
Contents of the box
Upon receiving MyPBX U510 gift box, please open the package and check if all the items are supplied as
MyPBX U510 Packing List (See Sheet 1). If there is any problem, please contact your provider.
Item
Unit
QTY
Description
MyPBX U510
PC
1
MyPBX U510 main box
Power cord
PC
1
For the input of 220V AC power
Warranty card
PC
1
With Series Number printed for Repair & Return
CD
PC
1
including all the MyPBX User Manuals and relative
documents
phone line
PC
2
Network Cable
PC
1
Serial Line
PC
1
SATA data line
PC
2
SATA power cord
PC
1
Mounting ear
PC
2
Screws
PC
12
8 screws (φ3.0*6mm) for mounting ears; 4 screws
(φ3.0*8mm) for hard disk brackets
Sheet 1 MyPBX U510 Packing List
http://www.yeastar.com
4/17
MyPBX U510 Installation Guide
2. Hardware Specifications
2.1 Overview
Figure 2-1 MyPBX U510
2.2 LED Indicators and Ports
Figure 2-2 MyPBX U510 Front Panel
Figure 2-3 MyPBX U510 Back Panel
http://www.yeastar.com
5/17
MyPBX U510 Installation Guide
LED
Power
Indication
Power status
Status
On
Off
RUN
MyPBX status
Blinking
Not Blinking/Off
1-16
FXO port status
Red light
GSM/
UMTS
Red light
port
status
BRI port status
Orange light
FXS port status
Green light
Ports
RJ11 ports
Antenna ports
E1/T1 port
Console port
Description
The power is switched on
The power is switched off
MyPBX is running properly
MyPBX goes wrong
The red light is blinking: no PSTN line connected
the lights are blinking red and green alternately: there
is incoming call
The lights are blinking red and green alternately and
rapidly: the call is connected and the trunk is in use.
The red light is blinking: no SIM card inserted
The lights are blinking red and green alternately: there
is incoming call
The lights are blinking red and green alternately and
rapidly: the call is connected and the trunk is in use.
Orange light: indicates the BRI port
The orange light is blinking: no BRI line connected
The orange light is on: the BRI line is connected or in
use
The lights are blinking green and red alternately: the
FXS port is ringing
The lights are blinking green and red alternately and
rapidly: the call is connected and the FXS port is in use
Description
FXO port (red light): For the connection of PSTN lines or FXS ports of traditional PBX.
MyPBX users could make or receive calls via FXO port.
FXS port (green light): For the connection of analog phones.
BRI port (orange light): For the connection of ISDN BRI lines. MyPBX users could make or
receive calls via BRI port.
Note: The sequence number of the ports corresponds to that of the Indicator lights in the
front panel. (I.e. the LED lights in the front indicate the connection status of the
corresponding ports at the front panel.)
For the connection of GSM/UMTS Antenna.
For the connection to E1 line or the E1 port of traditional PBX.
For debugging
USB port
Ethernet ports
MyPBX U510 provides two 10/100/1000M adaptive RJ45 Ethernet ports, marked as LAN
and WAN.
-LAN port: LAN port is for the connection to Local Area Network (LAN).
-WAN port: WAN port is the network port for the connection to internet. It supports ‘DHCP
server’, ‘PPPoE/dynamic DNS’, and “static IP” for IP address assignment.
Reset Button
Press the reset button to restore the factory defaults
Please make sure that you’d like to reset because once reset, the previous configurations
would be erased automatically.
Power port
For the connection of a power adapter to input 100~240V, 50~60HZ AC power
http://www.yeastar.com
6/17
MyPBX U510 Installation Guide
2.3 Specifications and Operating Environment
Description
Size
L 438 * W 280 * H 44 (mm)
Power Supply
220V, 50~60Hz
Operating Temperature
0°C~50°C (32°F~122°F)
Storage Temperature
-10°C~65°C (14°F~149°F)
Operating Humidity
5%~90% (Non-condensing)
Storage Humidity
0%~95% (Non-condensing)
Weight
3.4kg
http://www.yeastar.com
7/17
MyPBX U510 Installation Guide
3. MyPBX U510 Installation
To avoid unexpected accident, personal injury or device damage, please read the following instructions
before installing MyPBX U510.
3.1 Placement Instructions



Ambient Temperature: to avoid overheating, please do not run MyPBX U510 in the place where the
ambient temperature is above 122℉ (50℃ ).
Ventilation: please make sure that the device has good ventilation around.
Anti-jamming—there may be some sources of interference that might affect the normal running of
MyPBX U510. It’s highly recommended that the device
 Should be placed away from high-power radio, radar transmitters and high frequency, and
high-current devices.


Is using independent power junction box and effective anti-grid interference measures have been
taken.
Mechanical load--Please make sure that the device is placed steadily to avoid any accident that might
cause damage. If placed on the desktop, please ensure it is horizontally placed.
3.2 Installation Instructions
After placing MyPBX U510 in a suitable place, please connect the power adapter and all other cables to
complete the installation.
3.2.1 Connection of Ethernet Ports
MyPBX U510 provides two 10/100/1000M adaptive RJ45 Ethernet ports, that is, LAN port and WAN port.

WAN Port Connection
Connect one end of a network cable to the WAN port of MyPBX U510, and the other end to the Ethernet
port of a hub, switch or ADSL modem.
 LAN Port Connection
Connect one end of a network cable to the LAN port of MyPBX U510, and the other end to any port of
company’s LAN switch/router.
If the LAN port is connected to PC directly (not via a switch), please use cross-over cable.
http://www.yeastar.com
8/17
MyPBX U510 Installation Guide
3.2.2 Connection of E1/T1/FXO/GSM/UMTS/BRI ports
MyPBX U510 supports various outside lines (e.g. E1/T1, FXO, GSM/UMTS, or BRI). Below are the connection
instructions of each kind of outside line taking the device installed with 1 E1/T1, 2 FXO ports, 2 GSM ports,
and 2 BRI ports as an example.
1. Connection of E1/T1 port
The E1/T1 port could be connected to the E1 line or the E1 port of traditional PBX.
Note: the E1/T1 port of MyPBX U510 is RJ45 port, and the pins are defined as below table:
Item
Description
1
2
RX- Receive DataRX+ Receive Data+
3
Not used
4
TX- Transmit Data-
5
TX+ Transmit Data+
6
Not used
7
Not used
8
Not used
Note: Please follow the below steps to make RJ45 cable to connect it to the E1 port.
Step 1: Connect MyPBX U510 E1 port to the E1 line according to the line sequence of E1 port.
From the above table, we can see that the No.1 and No.2 pins of MyPBX U510 E1 port is for receiving
data (No.1 for receiving data -, No.2 for receiving data +), while No.4 and No.5 is for transmitting data
(No.4 is for transmitting data -, No.5 is for transmitting data +).
When connected to the E1 line, RX- of E1 port should be connected to TX- of E1 line; RX+ of E1 port
should be connected to TX+ of E1 line; TX- of E1 port should be connected to RX- of E1 line; TX+ of E1
port should be connected to RX+ of E1 line.
For example, the line sequence o f the E1 line (RJ45 port) provided by the telecom company is: No.4 for
TX-, No.5 for TX+, No.7 for RX- and No.8 for RX+ which apparently can’t correspond to that of MyPBX
U510 E1 port. So you need jumper, which could be depicted as below:
Figure 3-1 E1 Cable Cord Sequence
http://www.yeastar.com
9/17
MyPBX U510 Installation Guide
Step 2: Connect the self-made RJ45 cable to E1 port.
Figure 3-2 Connection of E1/T1 port
2. Connection of FXO ports
The FXO port could be connected to the PSTN line or the FXS port of a traditional PBX with a phone line.
For instance, if No.2 and No.4 connectors are FXO ports, the connection could be depicted as below:
Figure 3-3 Connection of FXO ports and status LED
3. Connection of GSM/UMTS ports
If No.3 and No.7 connectors are GSM/UMTS Ports, the steps of connection are as below:
Step 1: Open the Upper case of MyPBX U510
Step 2: Insert the SIM card as below:
Figure 3-4 Inserting the SIM Card
http://www.yeastar.com
10/17
MyPBX U510 Installation Guide
Step 3: Connect the antenna
Once completed, the No.3 and No.7 LED lights would turn red as below figure:
Figure 3-5 Connection of GSM/UMTS ports and Status LED
4. Connection of BRI ports
The BRI port could be connected to the BRI line and the BRI port of a traditional PBX with a BRI RJ45-RJ11
cable.
For instance, if No.14 and No.16 connectors are BRI ports, the connection could be depicted as below:
Figure 3-6 Connection of BRI ports and Status LED
http://www.yeastar.com
11/17
MyPBX U510 Installation Guide
3.2.3 Connection of FXS ports
The FXS port could be connected to an analog phone with a phone line.
For instance, if No.6 and No.8 connectors are FXS ports, the connection could be depicted as below:
Figure 3-7 Connection of FXS ports and Status LED
3.2.4 Power Connection
Once users have made sure that device installation, cable connection and power type is correct, please
switch on the power. Then MyPBX U510 will start booting. In the meantime, users would see that the
‘POWER’ and ‘RUN’ indicator lights would turn on.
Please switch off the power before plugging or unplugging the cables.
3.2.5 Overall Flow Chart
Figure 3-8 Overall Flow Chart
http://www.yeastar.com
12/17
MyPBX U510 Installation Guide
4. MyPBX U510 Basic Configurations
4.1 Factory Defaults
MyPBX U510 provides web-based configuration interface for administrator and account user. The user can
manage the device by log in the web interface.
The factory default IP address:
LAN: 192.168.5.150;
Access path: http://[IP address]
User Name: admin;
Password: password
Default SIP UDP port: 5060
There are 6 extensions set up by default. The user could use these extensions directly, edit or delete them.
Their extension numbers are “300”-“305” (6 numbers in a row) whose passwords are “pincode + respective
extension number”.
4.2 Logging in the Web Configuration Panel
Firstly, please check if the IP address that assigned to the network port (LAN or WAN) is in the same segment
with the PC and which can be connected when commit ‘Ping +MyPBX IP address’ command. Start the
browser on PC. In the address bar, enter the IP address, click ‘enter’ button and then you can see MyPBX
Web Configuration Panel login page (See Figure 4-1).
Figure 4-1 MyPBX Web Configuration Panel Login Page
Enter the Admin User Name and Password to log in.
http://www.yeastar.com
13/17
MyPBX U510 Installation Guide
Figure 4-2 MyPBX Admin Configuration Interface
Via the configuration interface, the admin can make all the system configurations, including network settings
(LAN, WAN, Firewall, VPN, DDNS, VLAN, etc.); system parameters configuration (system prompts, time zone,
password, etc.); internal settings (Web access port, user extension range, business hours, conference room,
paging and intercom, music on Hold, etc.); inbound routes; outbound routes; user account management (add
or delete an extension account, IP restriction, features setup, etc.); extended function management (call
queue, conference room, IVR, etc.); call logs (search, download); firmware update and reset, etc.
Please note that after saving the changes, remember to click the “Apply changes” button to make the
changes take effect.
http://www.yeastar.com
14/17
MyPBX U510 Installation Guide
4.3 Network Settings
After logging in the admin configuration interface, generally the first step is to configure the IP address. If
both the WAN and LAN ports are connected to the network, their IP addresses need to be configured. If not,
just configuring the IP address of the LAN port which is connected to the local area network of the company
is OK.
 WAN Settings
Click “Network Preference”->”WAN Settings” on the left menu bar.
1. If the network that the WAN port is connected to is using DHCP server as connection method, please
select the “DHCP” (dynamic IP) option.
2. If the network connection method is “Static IP address”, please select this option and enter the WAN
parameters (IP address, subnet mask, default gateway, DNS, etc.)
3. If MyPBX is connected to ADSL adapter directly, please select “PPPoE” option and enter the ADSL
user name and password.
 LAN Settings
Click “Network Preference”->”LAN Settings” on the left menu bar of the web configuration interface.
LAN port is used for the interoperability of IP terminals and MyPBX. If the LAN port is connected to the
company’s LAN, please configure the correct IP address and corresponding subnet mask.
Please note that after changing the IP address of LAN port, MyPBX should be rebooted to make the new
changes take effect.
4.4 Extensions Setup and management
MyPBX has already set up 6 extensions which are extensions “300-305” by default. The password is “pincode
+ extension number”. It’s up to the user to decide whether to directly use these default extensions or after
changing the password. Of course, they could be deleted.
The admin could add, edit or delete the extensions via the Web Configuration Panel.
In the “FXS/VOIP Extensions” page, there are “Add Extension”, “Add Bulk Extensions”, “Delete the Selected
Extension” and “Edit Extension”(configure the features such as call forwarding and voicemail) subpages, etc.
4.5 Configuring Terminals
MyPBX could be connected with SIP-based audio and video IP terminal devices (e.g. IP Phone, voice gateway,
and soft terminal, etc.). The steps of configuring terminals are as below:
Step 1: Make sure the IP terminal and MyPBX are interconnected
Step 2: Enter the IP address of MyPBX when configuring “SIP server”, “Proxy server”, or “Registration server”
of the IP terminals, and the default SIP UDP port is 5060.
Step 3: Enter the account registration information with the “extension number/password” of the default or
newly setup extensions of MyPBX.
For more information on terminal configuration, please refer to
http://www.yeastar.com/Solutions/SIP_Phones.asp
Step 4: Reboot the IP terminal after configuration, and click “Status”-> “Line Status”-> “Extension Status”on
the menu bar of MyPBX web configuration interface to check if it has registered successfully to MyPBX.
http://www.yeastar.com
15/17
MyPBX U510 Installation Guide
4.6 Making/Receiving calls
Note: The MyPBX default settings are sufficient to make phone calls. It is not necessary to make any changes
unless the user wants to create new extensions or trunks. Refer to Administrator’s Guide for more.
1. Internal calls between extensions
If two IP terminals have registered to MyPBX successfully, the user could make calls between extensions
just by dialing the other’s extension number.
2. Outbound calls
Firstly, please connect a PSTN line to the first FXO port. Then the default extensions are able to make
outbound calls via this trunk by simply dialing “9+phone number+#”. The “#” is Key as Send.
Note: The dial pattern of the default outbound route is “9.”. But if the user has changed it, please dial the
new prefix instead of the digit “9” when making outbound calls.
3. Inbound calls
When the user calls the trunk number of the PSTN line, MyPBX would route the call to IVR (the
“welcome” prompt) by default. Then the user can dial the extension number following the prompt.
4.7 Reset to Factory Defaults
If you forget the new IP address or the password of admin, or in other cases that you would like to restore
the factory defaults, please reset the device following the instructions below:
Please press the “RESET” button located in the back panel with a paper clip or a pencil tip, then you can see
all of the LED indicators in the front panel would keep them color first and turn orange seconds later. When
the indicator light becomes orange, the button could be released and system begins to reset. During the
process, please do not power off until the LED indicators become normal which means the reset process is
completed.
Note: After resetting, all the configurations made by the admin would be erased.
http://www.yeastar.com
16/17
MyPBX U510 Installation Guide
5. Conclusion
This Installation Guide only explains the installation and basic settings of MyPBX U510 for making and
receiving calls. For more functionality and advanced settings of MyPBX U510, please refer to the relative
documents as below:
“MyPBX U510 Datasheet”
“MyPBX U510 Administrator’s Guide”
“MyPBX U510 Extension User’s Guide”
[The End]
http://www.yeastar.com
17/17
U5 series
Administrator's Guide
Version 14.18.0.22
Yeastar Technology Co., Ltd.
MyPBX U5XX Administrator's Guide
Table of Contents
1. Introduction ......................................................................................... 5
1.1 Features ......................................................................................... 6
1.2 Hardware Specifications .................................................................... 7
1.2.1 Exterior Appearance ...............................................................................7
2. System Setup ...................................................................................... 8
2.1 Connection Drawing ......................................................................... 8
2.2 Connecting Ethernet Line .................................................................. 9
2.3 Supplying Power ............................................................................ 10
3 Administrator Login ............................................................................. 11
4 Status ................................................................................................ 13
4.1 Line status .................................................................................... 13
4.1.1 Extension Status .................................................................................. 13
4.1.2 Trunk Status ........................................................................................ 14
4.2 System Status ............................................................................... 16
4.2.1 System Info ......................................................................................... 16
4.2.2 Network Status .................................................................................... 16
5 System .............................................................................................. 17
5.1 Network Preferences ...................................................................... 17
5.1.1 LAN Settings ........................................................................................ 17
5.1.2 WAN Settings ....................................................................................... 18
5.1.3 DHCP Server ........................................................................................ 19
5.1.4 VLAN Settings ...................................................................................... 20
5.1.5 VPN Settings ........................................................................................ 22
5.1.6 DDNS Settings ..................................................................................... 23
5.1.7 Static Route ......................................................................................... 23
5.2 Firewall Settings ............................................................................ 25
5.2.1 Firewall Rules ....................................................................................... 25
5.2.2 IP blacklist ........................................................................................... 27
5.3 System Preference ......................................................................... 28
5.3.1 Password Settings ................................................................................ 28
5.3.2 Date and Time ..................................................................................... 30
5.3.3 Firmware Update .................................................................................. 30
5.3.4 Backup and Restore .............................................................................. 31
5.3.5 Reset and Reboot ................................................................................. 31
5.3.6 Hot Standby ........................................................................................ 32
5.3.7 AMI Settings ........................................................................................ 34
5.3.8 Alert Settings ....................................................................................... 34
5.3.9 Database Grant .................................................................................... 37
5.3.10 Security Center .................................................................................. 38
5.4 Storage Management ..................................................................... 39
5.4.1 Disk Management ................................................................................. 39
5.4.2 External Storage .................................................................................. 40
www.yeastar.comPage2
MyPBX U5XX Administrator's Guide
6 PBX ................................................................................................... 42
6.1 Extensions .................................................................................... 42
6.1.1 FXS/VoIP Extensions ............................................................................. 42
FXS Extensions ............................................................................................. 43
VoIP Extensions ............................................................................................ 47
6.1.2 Phone Provisioning ............................................................................... 52
6.2 Trunks .......................................................................................... 61
6.2.1 Physical Trunk ...................................................................................... 61
6.2.2 VoIP Trunk ........................................................................................... 72
6.3 Outbound Call Control .................................................................... 79
6.3.1 Outbound Routes.................................................................................. 79
6.3.2 Speed Dial Settings .............................................................................. 82
6.4 Inbound Call Control ...................................................................... 83
6.4.1 IVR ..................................................................................................... 83
6.4.2 Ring Groups ......................................................................................... 85
6.4.3 Queues ............................................................................................... 87
6.4.4 Conferences ......................................................................................... 91
6.4.5 Inbound Routes .................................................................................... 92
6.5 Audio Settings ............................................................................... 98
6.5.1 Custom Prompts ................................................................................... 98
6.5.2 Music on Hold Prompts .......................................................................... 99
6.5.3 System Prompts Settings .................................................................... 100
6.6 Basic Settings.............................................................................. 101
6.6.1 General Preferences ............................................................................ 101
6.6.2 Business Hours .................................................................................. 103
6.6.3 Feature Codes .................................................................................... 105
6.6.4 Voicemail Settings .............................................................................. 108
6.7 Advanced Settings ....................................................................... 111
6.7.1 SIP Settings....................................................................................... 111
6.7.2 IAX Settings ...................................................................................... 117
6.7.3 Blacklist ............................................................................................ 118
6.7.4 Callback Settings ................................................................................ 119
6.7.5 DNIS Settings .................................................................................... 121
6.7.6 DISA ................................................................................................. 121
6.7.5 PIN User Settings ............................................................................... 122
6.7.8 Paging Groups.................................................................................... 124
6.7.9 SMS Settings ..................................................................................... 125
6.7.10 Certificates ...................................................................................... 127
7 Reports ............................................................................................ 129
7.1 Call Logs ..................................................................................... 129
7.2 System Logs ............................................................................... 130
8 Addons ............................................................................................. 131
8.1 MyPBX Client ............................................................................... 131
8.2 Billing System ............................................................................. 131
www.yeastar.comPage3
MyPBX U5XX Administrator's Guide
8.3 Hotel Module ............................................................................... 132
9 Logout ............................................................................................. 133
10. Use MyPBX..................................................................................... 134
10.1 Make outbound call .................................................................... 134
10.1.1 Sample Routing via E1 Trunk .............................................................. 135
10.1.2 Sample Routing via VoIP Trunk ........................................................... 136
10.2 Incoming call ............................................................................. 138
10.2.1 Sample Routing to an IVR .................................................................. 139
APPENDIX A FAQ .................................................................................. 140
APPENDIX B MyPBX Security Configuration Guide ..................................... 141
1. Security Configuration for Web GUI .................................................. 142
1.1 Change the default access port for HTTP on Options page .......................... 142
1.2 Change the default password for the web GUI .......................................... 143
2. Disable SSH on LAN Settings Page ................................................... 143
2.1 Disable SSH.......................................................................................... 143
2.2 Change the default password for SSH ...................................................... 144
3. Security Configuration for Extensions ............................................... 145
3.1 Change the default SIP Port .................................................................... 145
3.2 Disable guest calls................................................................................. 146
3.3 Security Configuration for remote extensions ............................................ 147
3.4Set a robust password and enable IP restriction for extensions .................... 147
4. Setup Proper Firewall Rules ............................................................. 148
5. Alert Settings ................................................................................ 156
APPENDIX C How to Configure external storage ....................................... 159
APPENDIX D How to Configure NAT setting .............................................. 161
APPENDIX E How to Use Auto Provision ................................................... 163
APPENDIX F HowDo I Configure Distinctive Ring Tones ............................. 167
APPENDIX G How to Use Email to SMS .................................................... 169
APPENDIX H How to Use DID ................................................................. 171
APPENDIX I How to Use BLF Key to Choose the PSTN line ......................... 175
APPENDIX J How to Enable Auto Recording .............................................. 176
J.1 Login .......................................................................................... 176
J.2 Recording Settings ....................................................................... 176
J.3 Recording Logs............................................................................. 177
J.4 Share setting ............................................................................... 178
J.5 Password Setting .......................................................................... 180
www.yeastar.comPage4
MyPBX U5XX Administrator's Guide
1. Introduction
MyPBX—IP-PBX for Medium Businesses/Home Office
New products MyPBX U5 series is a standalone embedded hybrid PBX for
medium businesses and remote branch offices of larger organizations (1-300
users per site). MyPBX U5 series also offer a hybrid solution (a combination of
VoIP applications using E1/T1/J1 equipment) alternative for enterprises who are
not yet ready to migrate to a complete VoIP solution.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radiofrequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
FCC Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user‟s authority to operate this equipment.
FCC Warning
This equipment has been tested and found to comply with the regulations for a
Class B digital device, pursuant to Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received including interference
that may cause undesired operation.
www.yeastar.comPage5
MyPBX U5XX Administrator's Guide
1.1 Features
● Auto-provision
● Follow me
● Optional Hard disk
● Interactive Voice Response (IVR)
● BLF Support
● Intercom / Zone Intercom
● Blacklist
● Music On Hold
● Call transfer
● Hot standby
● Call Detail Records(CDR)
● Paging / Zone Paging
● Call Forward
● PIN Users
● Call Parking
● Queue
● Call Recording
● QOS
● Call Pickup
● Ring Group
● Call Routing
● Route by Caller ID
● Call Transfer
●Spy functions
● Call Waiting
● Skype Integration (Skype Connect)
● Caller ID
● Three-way Calling
●Call Back
●Mobility Extension
●Conference
●External Storage
●Speed Dial
●DDNS
● Define Office Time
●OpenVPN
● Direct Inward System Access(DISA)
● T.38
● DIDs
● Voicemail
● Distinctive Ringtone
● VLAN
● Do Not Disturb(DND)
● WAN
● Dial by Name
●PPPoE
● Firewalls
● Static Route
More info,
MyPBX U500: http://www.yeastar.com/products/MyPBX-U500.asp
MyPBX U510:http://www.yeastar.com/products/MyPBX-U510.asp
MyPBX U520: http://www.yeastar.com/Products/MyPBX-U520.asp
www.yeastar.comPage6
MyPBX U5XX Administrator's Guide
1.2 Hardware Specifications
1.2.1 Exterior Appearance
Front Panel
①
②
③
④ ⑤ ⑥ ⑦ ⑧⑨ ⑩
Figure1-1 MyPBXU5XX Front Panel
No.
Indication
①
16 Green LEDs
②
16 RJ11 ports
③
④
E1/T1 interface
None E1/T1 available in MyPBX U500
1*E1/T1 available in MyPBX U510
2*E1/T1 available in MyPBX U520
⑤
Console port (RJ45)
⑥
WAN port
⑦
LAN port
⑧
USB port
⑨
Reset Button
⑩
Power and Run indicator
www.yeastar.comPage7
MyPBX U5XX Administrator's Guide
2. System Setup
2.1 Connection Drawing
Figure 2-1 U5XX Connection Drawing
www.yeastar.comPage8
MyPBX U5XX Administrator's Guide
2.2 Connecting Ethernet Line
MyPBX provides two 1000M Ethernet ports with RJ45 interface and LED
indicator. Plug Ethernet line into MyPBX‟s Ethernet port, and then connect the
other end of the Ethernet line with a hub, switch, router, LAN or WAN. Once
connected, check the status of the LED indicator. A yellow LED indicates the port
is in the connection process, and a green LED indicates the port is properly
connected.
www.yeastar.comPage9
MyPBX U5XX Administrator's Guide
2.3 Supplying Power
Please follow the steps below to connect the MyPBX unit to a power outlet:
1. Connect the small end of the power cable to the power input port on the
MyPBX back panel, and plug the other end of the cable into a 100V~240V
AC power outlet.
2. Check the Power LED on the front panel. A solid green LED indicates that
power is being supplied correctly.
www.yeastar.comPage10
MyPBX U5XX Administrator's Guide
3 Administrator Login
From your web browser, input the IP address of the MyPBX server.
If this is the first time you are configuring MyPBX, please use the default settings
as below (your PC should be in the same local network with MyPBX):
IP Address: http://192.168.5.150
Note: MyPBX supports multiple administrators in hierarchical mode
( Administrator, General Manager, CDR Manager)
·
Administrator
have all the authority .
Username: admin , Password:password
·
General Manager
have basic authority; without the advanced authority to create VoIP trunks,
reset, update, backup and restore MyPBX.
Username: user, Password:password
You should enable this account before you use it.
·
CDR Manager
only have the authority to check the call recordings.
Username: cdr, Password:password
In this example, the IP address is 192.168.5.149
Figure 3-1 Login Page
www.yeastar.comPage11
MyPBX U5XX Administrator's Guide
This is the welcome page of MyPBX U5XX after successful login.
Figure 3-2 Welcome Page
www.yeastar.comPage12
MyPBX U5XX Administrator's Guide
4 Status
Click
to start to check the status of MyPBX U5XX, where we can check
the status of extension, trunk, and network and system information.
4.1 Line status
In this page, we can check the status of extension and trunks
4.1.1 Extension Status
Figure 4-1 Extension Status Page
MyPBX Status Description:
Extensions:
1)
: Extension is unavailable
2)
:Extension is idle
3)
:Extension is ringing
4)
:Extension is busy
5)
: Extension is on hold
www.yeastar.comPage13
MyPBX U5XX Administrator's Guide
4.1.2 Trunk Status
Figure 4-2 Trunk Status Page
Trunks:
Note:
E1/T1/J1 trunk in MyPBX U5XX
number of
E1/T1/J1
MyPBX U500
MyPBX U510
MyPBX U520
0
1
2
VOIP Trunk:
Status
Rejected: Trunk registration failed.
Registered: Successful registration, trunk is ready for use.
Request Send: Registering.
Waiting: Waiting for authentication.
Service Provider:
Status
OK: Successful registration, trunk is ready for use.
Unreachable: The trunk is unreachable.
Failed: Trunk registration failed.
FXO Trunk:
Status
Idle: The port is idle.
Busy: The port is in use.
Disconnected: The port hasn‟t connected to the PSTN line.
More detail message, please refer to the LED indication of front panel.
www.yeastar.comPage14
MyPBX U5XX Administrator's Guide
GSM Trunk:
Status
Idle: The port is idle.
Busy: The port is in use.
Signal
: No signal.
: Poor.
: Average.
: Good.
: Excellent.
BRI Trunk:
Status
Ok: The ports connect correctly.
Disconnected: The port hasn‟t connected to the BRI line or the signaling
mismatch.
E1 Trunk:
Connect
Alarm
Comment
The port doesn‟t have E1 line connected.
E1 line has been connected to the port; PRI is in
corresponding or can‟t communicate.
Succeed.
www.yeastar.comPage15
MyPBX U5XX Administrator's Guide
4.2 System Status
In this page, we can check the status of MyPBX system, including the
hardware ,firmware version and the network status of LAN and WAN ports .
4.2.1 System Info
In this page, we can check the hardware/firmware version, or the disk usage of
MyPBX.
Figure 4-3 System Information
4.2.2 Network Status
In this page, the IP address of LAN and WAN port will appear, if OpenVPN is
configured well, the information will be displayed here too.
Figure 4-4 Network Status
www.yeastar.comPage16
MyPBX U5XX Administrator's Guide
5 System
Click
to access.
In this page, we can configure the network settings, firewall settings, storage
management and some other preferences like firmware update and hot
standby.
5.1 Network Preferences
5.1.1 LAN Settings
Figure 5-1 LAN Settings
·
DHCP
If this option is set, MyPBX will use DHCP to get an available IP address from
your local network. Not recommended or you cannot access MyPBX without
the right IP address
·
Enable SSH
This is the advance way to access the device, you can use the putty software
to access the device.In the SSH access, you can do more advanced settings
and debug. Disabled by default.
·
Port: the default is 8022; you change it to another one.
www.yeastar.comPage17
MyPBX U5XX Administrator's Guide
·
Hostname
Set the host name for MyPBX.
·
IP Address
Set the IP Address for MyPBX.
Recommend to configure a static IP address for MyPBX
·
Subnet Mask
Set the subnet mask for MyPBX.
·
Gateway
Set the gateway for MyPBX.
·
Primary DNS
Set the primary DNS for MyPBX.
·
Secondary DNS
Set the secondary DNS for MyPBX.
·
IP Address2
Set the second IP Address for MyPBX.
·
Subnet Mask2
Set the second subnet mask for MyPBX.
5.1.2 WAN Settings
Figure 5-2 WAN Settings
It supports three connection types: DHCP (obtain an IP automatically), PPPoE,
Static IP Address.
Notes:
www.yeastar.comPage18
MyPBX U5XX Administrator's Guide
1. WAN port is disabled by default
2. WAN port cannot be used as a router to route the internet packages from
WAN port to LAN port.
·
DHCP
.If your ISP says that you are connecting through DHCP or a dynamic IP address
from your ISP, perform these steps:
Step1: Select DHCP as the WAN Connection Type.
Step2: Click Save button to save the settings.
Step3: Reboot the device.
Step4: Check the WAN‟s Status (Status  Network status).
·
Static IP Address
If your ISP says that you are connecting through a static or fixed IP address
from your ISP, perform these steps:
Step1: Select Static IP Address as the WAN Connection Type.
Step2: Enter the IP Address.
Step3: Enter the Subnet Mask.
Step4: Enter the Gateway Address.
Step5: Enter the Primary DNS and Secondary DNS.
Step6: Click the Save button to save the settings.
Step7: Reboot the device.
Step8: Check the WAN‟s Status (Status  Network status).
·
PPPoE
If your DSL provider says that you are connecting through PPPoE or if you
normally enter a user name and password to access the Internet, perform these
steps:
Step1: Select PPPoE as the WAN Connection Type.
Step2: Enter the User Name.
Step3: Enter the Password.
Step4: Click the Save button to save the settings.
Step5: Reboot the device.
Step6: Check the WAN‟s Status (Status  Network status)
5.1.3 DHCP Server
Dynamic Host Configuration Protocol (DHCP) is a network protocol that enables
a server to automatically assign an IP address to a computer from a defined
range of numbers (i.e., a scope) configured for a given network. You can also
www.yeastar.comPage19
MyPBX U5XX Administrator's Guide
set a local network NTP server for MyPBX here.
Note1: When using „Phone Provisioning‟ for Grandstream IP phone, Enter the IP
address of the server directly, e.g.:192.168.5.150; for other phones using the
default configuration.
Note2: MyPBX U5XX can work as a DHCP server, but cannot be regarded as a
router.
Figure 5-3 DHCP Server Settings
5.1.4 VLAN Settings
A VLAN (Virtual LAN) is a logical local area network (or LAN) that extends
beyond a single traditional LAN to a group of LAN segments, given specific
configurations.
Note: MyPBX U5XX is not the VLAN server, a 3-layer switch is still needed,
please configure the VLAN information there first, then input the details in
MyPBX, so that the packages via MyPBX will be added the VLAN label before
sending to that switch.
Figure 5-4 VLAN Settings
www.yeastar.comPage20
MyPBX U5XX Administrator's Guide
1) VLAN Over Lan
·
NO.1
Click the NO.1 you can edit the first VLAN over Lan.
·
VLAN Number
.The VLAN Number is a unique value you assign to each VLAN on a single device.
·
VLAN IP Address
Set the IP Address for MyPBX VLAN over Lan.
·
VLAN Subnet Mask
Set the Subnet Mask for MyPBX VLAN over Lan.
·
Default Gateway
Set the Default Gateway for MyPBX VLAN over Lan
·
NO.2
Click the NO.2 you can edit the first VLAN over Lan.
·
VLAN Number
.The VLAN Number is a unique value you assign to each VLAN on a single device.
·
VLAN IP Address
Set the IP Address for MyPBX VLAN over Lan.
·
VLAN Subnet Mask
Set the Subnet Mask for MyPBX VLAN over Lan.
·
Default Gateway
Set the Default Gateway for MyPBX VLAN over Lan.
2) VLAN Over Wan
·
NO.1
Click the NO.1 you can edit the first VLAN over Wan.
·
VLAN Number
.The VLAN Number is a unique value you assign to each VLAN on a single device.
·
VLAN IP Address
Set the IP Address for MyPBX VLAN over Wan.
·
VLAN Subnet Mask
www.yeastar.comPage21
MyPBX U5XX Administrator's Guide
Set the Subnet Mask for MyPBX VLAN over Wan.
·
Default Gateway
Set the Default Gateway for MyPBX VLAN over Wan.
·
NO.2
Click the NO.2 you can edit the first VLAN over Wan.
·
VLAN Number
.The VLAN Number is a unique value you assign to each VLAN on a single device.
·
VLAN IP Address
Set the IP Address for MyPBX VLAN over Wan.
·
VLAN Subnet Mask
Set the Subnet Mask for MyPBX VLAN over Wan.
·
Default Gateway
Set the Default Gateway for MyPBX VLAN over Wan.
5.1.5 VPN Settings
A virtual private network (VPN) is a method of computer networking--typically
using the public internet--that allows users to privately share information
between remote locations, or between a remote location and a business' home
network. A VPN can provide secure information transport by authenticating
users, and encrypting data to prevent unauthorized persons from reading the
information transmitted. The VPN can be used to send any kind of network
traffic securely. MyPBX supports OpenVPN.
Figure 5-5 OpenVPN Settings
·
Enable VPN
·
Import VPN Config
Import configuration file of OpenVPN.
Note: Don't configure 'user' and 'group' in the 'config' file.
You can get the configuration package from the OpenVPN provider.
www.yeastar.comPage22
MyPBX U5XX Administrator's Guide
5.1.6 DDNS Settings
DDNS(Dynamic DNS) is a method / protocol / network service that provides the
capability for a networked device, such as a router or computer system using
the Internet Protocol Suite, to notify a Domain Name System (DNS) name
server to change, in real time, the active DNS configuration of its configured
hostnames, addresses or other information.
Figure 5-6 DDNS Settings
·
Enable DDNS
·
DDNS Server
Select the DDNS server you sign up for service.
·
User Name
User name the DDNS server provides to you.
·
Password
User account‟s password .
·
Host Name
Note: DDNS allows you to access your network using domain names instead of
IP address. The service manages changing IP address and updates your domain
information dynamically. You must sign up for service through dyndns.org,
freedns.afraid.org, www.no-ip.com, www.zoneedit.com
5.1.7 Static Route
MyPBX will have more than one internet connection in some situations but it has
only one default gateway. You will need to set some Static Route for MyPBX to
force it to go out through different gateway when access to different internet.
The default gateway priority of MyPBX from high to low is OpenVPNWAN
portLAN port.
www.yeastar.comPage23
MyPBX U5XX Administrator's Guide
Figure 5-7 Static Route Settings Page
1) Route table
The current route rules of MyPBX
·
Destination
The destination network to be accessed to by MyPBX
·
Subnet Mask
Specify the destination network portion.
·
Gateway
Define which gateway MyPBX will go through when access to the destination
network.
·
Metric
The cost of a route is calculated by using what are called routing metric. Routing
metrics are assigned to routes by routing protocols to provide measurable
statistic which can be used to judge how useful (how low cost) a route is.
·
Interface
Define which internet port to go through.
2) Static Route Rules
You can add new static route rules here.
www.yeastar.comPage24
MyPBX U5XX Administrator's Guide
5.2 Firewall Settings
Firewalls are used to prevent unauthorized Internet users from accessing
private networks connected to the Internet, especially intranets. All messages
entering or leaving the intranet pass through the firewall, which examines each
message and blocks those that do not meet the specified security criteria.
5.2.1 Firewall Rules
Figure 5-8 Firewall Settings
1) General Settings
·
Enable Firewall
Enable the firewall to protect the device.
·
Disable Ping
Enable this item, net ping from remote hosts will be dropped.
·
Drop All
When you enable “Drop All” feature, system will drop all packets or connection
from other hosts if there are no other rules defined. To avoid locking the devices,
at least one “TCP” accept common rule must be created for port used for SSH
access, port used for HTTP access and port sued for CGI access.
2) Common Rules
There is no default rule, you can create them as required.
www.yeastar.comPage25
MyPBX U5XX Administrator's Guide
Figure 5-9 Add Common Rules
·
Name
A name for this rule, e.g. “HTTP”.
·
Description
Simple description for this rule. E.g.: Accept the specific host to access the web
interface for configuration.
·
Protocol
The protocols for this rule.
·
Port
Initial port should be on the left and end port should be on the right.
The end port must be equal to or greater than start port.
·
IP
The IP address for this rule. The format of IP address is: IP/mask
E.g. 192.168.5.100/255.255.255.255 for IP 192.168.5.100
E.g.216.207.245.47/255.255.255.255 for IP 216.207.245.47
E.g.192.168.5.0/255.255.255.0 for IP from 192.168.5.0 to 192.168.5.255 .
·
MAC Address
The format of MAC Address is XX:XX:XX:XX:XX:XX, X means 0~9 or A~F in hex,
the A~F are not case sensitive.
Note: The MAC address will be changed when it‟s remotely device, so it will
not be working to filter using MAC for remote devices.
·
Action
Accept: Accept the access from remote hosts.
Drop: Drop the access from remote hosts.
Ignore: Ignore the access.
www.yeastar.comPage26
MyPBX U5XX Administrator's Guide
3) Auto Defence
By default, there is no rule.
Figure 5-10 Add Auto Defense Rule
Port
The port you want to auto defense, for example, 8022.
Protocol:
Select the protocol. You can select UDP or TCP.
Rate:
The maximum packets or connections can be handled per unit time.
For example, if you configure it as below:
Port: 8022
Protocol: TCP
Rate: 10/min
Then, it means maximum 10 TCP connections can be handled in 1 minute. The
11th connection will be dropped.
5.2.2 IP blacklist
You can set some packets accept speed rules here. When a IP address which
hasn‟t been accepted in common rules sends packets faster than the allowed
speed, it will be set as black IP address and blocked automatically.
Figure 5-11 IP Blacklist Settings Page
1) Blacklist rules
www.yeastar.comPage27
MyPBX U5XX Administrator's Guide
You can add the rules for IP blacklist rate as you wish.
Figure 5-12 Add Blacklist Rule
·
Port
Auto defense port
·
Protocol
Auto defense protocol. TCP or UDP.
·
IP Packets
Allowed IP packets number in the specific time interval.
·
Time interval
The time interval to receive IP packets. For example, IP packets 90, time
interval 60 means 90 IP packets are allowed in 60 seconds.
2) IP blacklist
The blocked IP address will display here, you can delete it as you wish.
5.3 System Preference
In this page, we can set other system preference, like the password for admin
account, system date and time, firmware update, hot standby, backup and
restore, reset and reboot.
5.3.1 Password Settings
MyPBX has 3 accounts: admin, user, and cdr. User and cdr account is disabled
by default.
Admin account:
The default password for account “admin” is “password”. To change the
password, select “admin” in “User”, enter the old password and new password,
click “Save”.The system will then prompt you to re-login using your new
password.
www.yeastar.comPage28
MyPBX U5XX Administrator's Guide
After you enter the new password, MyPBX will prompt the password strength. It
is recommended that you use numbers, upper-case letters, and lower-case
letters to increase the security.
When you log in MyPBX using “admin” account, you can enable “user” and “cdr”
account; also, you can change their passwords.
Figure 5-13 Modify admin‟s Password
User account:
User account is disabled by default and its default password is “password”.
When enabling “user” account for the first time, MyPBX will ask you to
change “user” password. If you don‟t change it, you can‟t enable “user” account.
To change the password, select “user” in “User”, enter the old password and
new password, click “Save”.The system will then prompt you to re-login using
your new password.
After you enter the new password, MyPBX will prompt the password strength. It
is recommended that you use numbers, upper-case letters, and lower-case
letters to increase the security.
Figure 5-14 Modify user‟s Password
After enabling “user” account, you can log in MyPBX using “user”. “user” account
can change its own password.
CDR account:
“cdr” account is disabled by default and its default password is “password”. You
can enable it after you log in MyPBX using “admin” account.
To change the password, select “cdr” in “User”, enter the old password and new
password, click “Save”.The system will then prompt you to re-login using your
new password.
After you enter the new password, MyPBX will prompt the password strength. It
is recommended that you use numbers, upper-case letters, and lower-case
www.yeastar.comPage29
MyPBX U5XX Administrator's Guide
letters to increase the security.
Figure 5-15 Modify cdr‟s Password
After enabling “cdr” account, you can log in MyPBX using “cdr”. “cdr” account
can change its own password.
5.3.2 Date and Time
Set the date and time for MyPBX.
Figure 5-16 Configuring Date&Time
·
Time Zone
You can choose your time zone here.
·
Daylight Saving Time
Set the mode to Automatic or disabled
·
Automatically Synchronize With an Internet Time Server
Input the NTP server so that MyPBX will update the time automatically
·
Set Date & Time Manually
You can set the time to your local right time manually here
5.3.3 Firmware Update
www.yeastar.comPage30
MyPBX U5XX Administrator's Guide
Upgrading of the firmware is possible through the Administrator web interface
using a TFTP Server or an HTTP URL.
Enter your TFTP Server IP address and firmware file name, then click start to
update the firmware
Notes:
1. If enabled “Reset configuration to Factory Defaults”, System will restore to
factory default settings.
2. When update the firmware, please don‟t turn off the power. Or the system will
get damaged.
3. More information for the steps to update the firmware, please refer to this link:
http://www.yeastar.com/download/MyPBX-U5XX/MyPBX_U5XX_FirmwareUpgr
ade_en.pdf
Figure 5-17 Firmware Update Page
5.3.4 Backup and Restore
We can backup up the configurations before reset MyPBXU5XX to factory
defaults, and then restore it using this package.
Notes:
1. Only configurations, custom prompts will be backed up, the voicemail and
recording files are not included.
2. When you have updated the firmware version, it‟s not recommended to
restore using old package.
Figure 5-18 Backup and Restore Page
5.3.5 Reset and Reboot
www.yeastar.comPage31
MyPBX U5XX Administrator's Guide
We can reset or reboot MyPBX U5XX via web directly in this page.
Figure 5-19 Reset and Reboot Options
·
Reboot System
Warning: Rebooting the system will terminate all active calls!
·
Reset to Factory Defaults
Warning: A factory reset will erase all configuration data on the system.
Please do not turn off the system until the RUN light begins blinking. Any power
interruption during this time could cause damage to the system.
5.3.6 Hot Standby
Redundancy is achieved by using duplicate hardware and software installations
and synchronizing data and operating state. Redundancy assures smooth
operation even if a system goes down. Essentially a duplicate backup system
takes over with virtually no loss of service. This technique assures absolute
reliability no matter what failure occurs. In mission critical installations,
redundancy is a way to address possibility of any failure.
Note 1: Before enabling the Hot Standby feature, please make sure that the
two servers in the failover pair are the same model, own the same modules
installed in the same slots, the same hardware configurations and firmware
version.
Note 2: Please configure the primary server first and configure the secondary
server only after the running status of primary server becomes “active”.
Note 3: The virtual IP address inputted in this page will be the one used for
registering in each IP phone.
Note 4: Before configuring the Email list in this page, please configure
the “voicemail settings” in “PBXBasic settings”, and make sure the SMTP test
successfully.
Note 5: Before configure the SMS list; please make sure the SIM and
GSM/UMTS modules are installed well
www.yeastar.comPage32
MyPBX U5XX Administrator's Guide
Figure 5-20 Hot Standby Configuration
Mode: Primary means the main unit; Secondary means the standby unit;
Secondary/Primary Hostname: If this unit mode is primary, then you need
to input the hostname of standby unit; vice versa, if this unit is selected as
secondary, then the hostname of primary unit is required. In brief, you need to
input each other‟s host name on this field.
IP: You need to input each other‟s IP address on this field.
Access code: To make an identification number to verify each other. The
number must be the same to both units.
Virtual IP address: To fill in a virtual IP address includes mask, which is
always points to the currently activated unit. Customer can register IP phones
through this virtual IP address. Please make sure the virtual IP address netmask
is the same on both units but different from their former IP address.
Network Connection Detection: Generally it requires the IP address of the
router or gateway that connects both units. MyPBX will connect another unit
through this IP address.
Down Notification: The way of informing customer that the system down.
Keep Alive: Every 2 seconds, a package will be sent from one unit to another,
which can test whether they are working properly.
Dead Time: The default setting is 120 seconds. If there‟s no response within
120s after one receiving a package from the other, then the normal working unit
will figure the other unit is dead and send an email or SMS to report the failure.
Disk Synchronization: It works for synchronizing the data on hard disk only,
www.yeastar.comPage33
MyPBX U5XX Administrator's Guide
such as the call recording files and CDR files saved in disk. The configurations in
MyPBX will not be influenced by this feature. 3 options are available: timing
synchronization, real-time synchronization and no.
5.3.7 AMI Settings
The Asterisk Manager Interface (AMI) is a system monitoring and management
interface provided by Asterisk. It allows live monitoring of events that occur in
the system, as well enabling you to request that Asterisk perform some action.
The actions that are available are wide-ranging and include things such as
returning status information and originating new calls. Many interesting
applications have been developed on top of Asterisk that take advantage of the
AMI as their primary interface to Asterisk.
There are two main types of messages on the Asterisk Manager Interface:
manager events and manager actions.
The 3rd party software can work with MyPBX using AMI interface. It is disabled
by default. If necessary, you can enable it.
Figure 5-21 AMI Settings
Username & password: after enabling AMI, you can use this username and
password to log in MyPBX AMI
IP Restriction: you can set which IP can log in MyPBX AMI interface
5.3.8 Alert Settings
If the device is attacked, the system will notify users the alert via call or E-mail.
The attack modes include IP attack and Web Login.
More details for the system security configuration, please refer toAPPENDIX
BMyPBX Security Configuration Guide.
www.yeastar.comPage34
MyPBX U5XX Administrator's Guide
Figure 5-22 Alert Settings
1.IPATTACK
When the system is attacked by IP address, the firewall will add the IP to auto
IP Blacklist and notify the user if it match the protection rule.
1) Phone Notification Settings
·
PHONE Notification
Whether enable phone notification.
·
Number
The numbers could be set for alert notification, users can setup multiple
extension and outbound phone numbers. Please separate them by “;”.
Example: “500;9911”, if the extension has configured Follow Me Settings, the
call would go to the forwarded number directly.
·
Attempts
The attempts to dial a phone number when there is no answer.
·
Interval
The interval between each attempt to dial the phone number. Must be greater
than 3 seconds, the default value is 10 seconds.
·
Prompt
Users will hear the prompt while receiving the phone notification.
2) E-mail Notification Settings
Note: Please ensure that all voicemail settings are properly configured on the
System Settings -> Voicemail Settings page before using this feature.
·
E-mail Notification
Whether enable E-mail Notification
·Recipient’s Name
The recipients for the alert notification, and multiple email addresses are
allowed, please separate them by “;”.
Example: jerry@yeastar.com;jason@yeastar.com, 456@sina.com .
www.yeastar.comPage35
MyPBX U5XX Administrator's Guide
·
Subject
The subject of the alert email.
·
Email Content
Text content support for predefined
corresponding instructions are as follows:
$(HOSTNAME)
$(LOCALIP)
$(SOURCEIP)
$(DATETIME)
$(USERNAME)
$(DESTMAC)
$(DESTPORT)
$(PROTOCOL)
$(INTERFACE)
variables.
Variable
names
and
Host name
Local IP address
Attack source IP address
Occurred
User name (WEBLOGIN effective)
Attacks destination MAC (IPATTACK effective)
Attacks destination Port number (IPATTACK effective)
Protocol type (IPATTACK effective)
Network interface name (IPATTACK effective)
Figure 5-23 IP Attack Configuration
2.WEBLOGIN
Web Login Alert Notification: Enter the password incorrectly five times to login
MyPBX Web interface will be considered as an attack, the system will limit the IP
www.yeastar.comPage36
MyPBX U5XX Administrator's Guide
login within 10 minutes and notify the user.
Figure 5-24 Web Login Alert Setting
5.3.9 Database Grant
U5XX are using MySQL database from 14.18.0.22. The 3rd party software can
access MySQL via internet. Before that, you need to grant the authority to the
database user.
After entering “Database Grant” page, clicking “Add”, you can add a database
user, set user password and grant authority.
Figure 5-25 Database Grant
Username/password: The 3rd party can use this username and password to
access the MySQL.
Database: there are 2 options, CDR and Record. If you choose CDR, then this
user has authority to check CDR database; if you choose Record, then the user
www.yeastar.comPage37
MyPBX U5XX Administrator's Guide
has authority to check which call has been recorded automatically.
5.3.10 Security Center
You can check MyPBX security configuration in “Security Center” page. And also,
you can enter the relevant security settings page rapidly.
Firewall:
Figure 5-26 Security Center-Firewall
In the “Firewall” tab, you can check firewall configuration and alert settings. By
clicking the relevant button, you can enter the configuration page directly.
Service:
Figure 5-27 Security Center-Service
In “Service” tab, you can check AMI/SSH/TFTP status. For AMI/SSH, you can
enter the according page by clicking the button in “Setting” column. For TFTP,
you can directly disable or enable it.
Port:
Figure 5-28 Security Center-Port
In “Port” tab, you can check SIP port and HTTP port. You can also enter the
relevant page by clicking the button in “Setting” column.
www.yeastar.comPage38
MyPBX U5XX Administrator's Guide
5.4 Storage Management
5.4.1 Disk Management
You can check the information of the hard disk, manage the disk and do some
related configuration.
·
Device Information
It‟s the information of the hard disk.
·
Disk Management
You can format disk or clean up the disk here.
Note: Please check if you need to back up these files before formatting or
clearing up the hard disk. Don‟t power off the device during the period.
·
Other Settings
You can:
a. Save Voicemails in the Disk
b. Save One Touch Recording Files in the Disk
c. Save CDR in the Disk
If you want to enable auto recording, please refer to Appendix J
Figure 5-29 USB Device Management
www.yeastar.comPage39
MyPBX U5XX Administrator's Guide
5.4.2 External Storage
The External Storage feature is used to extend storage space. Once configured,
the files (voicemail, call recording files) created before the configured days will
be moved to the Net-Disk.
Note: The shared folder must be based on Windows operation system.
Before external storage can be properly configured, an SMB share folder
accessible from MyPBX must be set up on a Windows based machine. Once
that has been set up, please follow the steps below.
Figure 5-30 External Storage Settings
Step
Step
Step
Step
1:
2:
3:
4:
Choose a window-based computer that is always in service
Create a folder
Create a text file named "status.txt" in the folder
Share this folder
Then we need input the Net-Disk information in step2 page.
www.yeastar.comPage40
MyPBX U5XX Administrator's Guide
Figure 5-31 Enter the Net-disk information
Net-Disk Host/IP:Change this to the IP address of the computer where
backup files will be stored.
Net-DiskShare Name: Change this to the name of the shared folder where
backups will be stored.
Net-DiskShare Username: The user name used to log into the network
share. Leave this blank if it is not required
Net-DiskShare Password: The password used to log into the network
share.Leave this blank if it is not required
If configuringis correctly, open your Windows share folder to see if the
MyPBX backup files and folders has been created.If the contents of the
backup folder look similar to step3 page, then you have successfully
configured external storage on the MyPBX unit.
Figure 5-32 Configuring External Storage Successfully
www.yeastar.comPage41
MyPBX U5XX Administrator's Guide
6 PBX
Click
to access
In this page, we can configure the settings of extension, trunk, inbound call
control, outbound call control, audio settings and the others. When configured
well, we can make calls as scheduled
6.1 Extensions
In this page, we can configure the extensions‟ details and provision the
supported models automatically.
6.1.1 FXS/VoIP Extensions
There are three types of extensions supported in MyPBX U5XX: SIP, IAX and
analog extension.
Figure 6-1 Extension List
www.yeastar.comPage42
MyPBX U5XX Administrator's Guide
FXS Extensions
Figure 6-2 FXS Extension List
There are two analog extensions in MyPBX U5XX if S2 module is installed, to
modify the extension number, please delete it first, then recreate it again
1) General
Figure 6-3 Edit FXS Extension
·
Extension
The numbered extension, i.e. 1234, that will be associated with this particular
User / Phone.
·
Port
The extension correspond port.
www.yeastar.comPage43
MyPBX U5XX Administrator's Guide
·
Name
A character-based name for this user, i.e. „Bob Jones‟ .
·
Caller ID
The Caller ID (CID) string will be used when this user calls another internal user.
2) Voicemail
·
Enable Voicemail
Check this box if the user should have a voicemail account.
·
Voicemail Access PIN #
Voicemail Password for this extension, i.e. „1234‟.
3) Mail Setting
·
Enable Send Voicemail
Once enabled, the voicemail will be sent to the email address belowas an
attachment.
·
Send Voicemail to Email Address
This option defines whether or not voicemails/Fax is sent to the Email address
asan attachment.
Note: Please ensure that all voicemail settings are properly configured on the
System Settings -> Voicemail Settings page before using this feature.
4) Flash
·
Hook Flash Detection
Sets the amount of time, in milliseconds, that must pass since the last
hook-flash event received by MyPBX before it will recognize a second event. If a
second event occurs in less time than defined byHook Flash Detection, then
MyPBX will ignore the event. The default value of Flash is 1000ms, and it can be
configured in 1ms increments.
5) Group
·
Pickup Group
If this extension belongs to a pickup group, any calls that ring this extension can
be picked up by other extensions in the same pickup group by dialing the Call
Pickup feature code (default *4).
Note: *4 is the default setting, it can be changed under Feature Codes ->
General -> Call Pickup.
6) Call Duration Settings
www.yeastar.comPage44
MyPBX U5XX Administrator's Guide
Setup the max cull duration for every call of this extension, but it‟s only valid for
outbound calls. Enter „0‟ or leave this blank empty, the value would be equal to
the max call duration configured in the Option Settings page.
Note: This setting will not be valid for internal calls.
Other Settings
Figure 6-4 FXS Extension Other Settings
7) Other options
·
Call Waiting
Check this option if the extension should have Call Waiting capability.If this
option is checked, the „When busy‟ follow me options will not be available.
·
DND
Don‟t Disturb.
·
User Web Interface
Check this option to allow the user to login to the MyPBX User Web interface,
which can be used to access voicemail and extension recordings. Users may
www.yeastar.comPage45
MyPBX U5XX Administrator's Guide
login the MyPBX User Web interface by using their extension number and
voicemail PIN # as the login and password respectively.
·
Ring Out
Check this option if you want to custom the ring time. Tone will stop over the
time defined
8) Follow me (Call Forwarding)
This function sets inbound call forwarding on an extension. An administrator can
configure FollowMe for this extension
9) Volume Settings
Rxgain: The Volume sent to FXS extension.
Txgain: The Volume sent out by the FXS extension
10) Mobility Extension
MyPBX allows you to use your mobile phone as extension. If you set your mobile
phone as mobility extension and then you call MyPBX with this mobility phone,
you will hear a dial tone. MyPBX will recognize your call as a call from an
extension. You can dial the number of other extensions (Your caller ID will be
the number of your extension) or dial out via outbound routes just like dialing
from your extension.
Note: If callback is enabled in the inbound route, the mobility extension
function of this inbound route will be disabled
11) Spy Settings
MyPBX allows extension to monitor/barge in other conversation. Once this
feature is enabled, the extension has the ability to monitor/barge in other calls
using the feature codes for each spy mode, refer to 'Feature Codes' page for
more information.
·
spy modes
There are 4 spy modes available for choice:
General spy: you have the permission to use the following 3 modes.
Normal spy: you can only hear the call, but can't talk
Whisper spy: you can hear the call, and can talk with the monitored extension
Barge spy: you can hear the call and talk with them both
Note: for example,if 500 want to monitor extension 501, we need to enable the
'allow being spied ' for 501, and choose the spy mode for extension 500.
Then pick up 500 and dial “feature codes + 501” to start monitoring when 501
is in a call
If 500 choose „normal spy‟, it should dial‟*90501‟ to start monitoring;
www.yeastar.comPage46
MyPBX U5XX Administrator's Guide
If 500 choose „whisper spy‟, it should dial „*91501‟ to start monitoring;
If 500 choose „barge spy‟, it should dial „*92501‟ to start monitor;
If 500 choose „general spy‟, it can dial „*90501‟,‟*91501‟ or „*92501‟ to start
monitor.
VoIP Extensions
A VOIP extension is a SIP/IAX Account that allows an IP Phone or an IP SoftPhone client to register onMyPBX
Figure 6-5 VOIP Extension List
We can click „Add extension‟ to start.
Figure 6-6 Add/Edit VOIP Extension
www.yeastar.comPage47
MyPBX U5XX Administrator's Guide
1) General
·
Type
Extension type: SIP,IAX or SIP/IAX.
SIP – The extension sends and receives calls using the VoIP protocol SIP.
IAX -The extension sends and receives calls using the VoIP protocol IAX.
·
Extension
The numbered extension, e.g. 1234, that will be associated with this particular
User / Phone.
·
Password
The password for this extension, e.g.“12t3f6”
·
Name
A character-based name for this user, e.g.“Bob Jones”
·
Caller ID
The Caller ID will be used when this user calls another internal extension.
2) Voicemail
·
Enable Voicemail
Check this box if the user should have a voicemail account.
·
Voicemail Access PIN #
The voicemail Password for this extension, i.e. „1234‟.
3) Mail Setting
This option defines whether or not voicemails or faxes are sent to an Email
Address as attachment.
·
Enable Send Voicemail
Once enabled, the voicemail will be sent to email as an attachment.
·
Email Address
Email address used to receive the voicemail or Fax.
Note: Please ensure that the section 'SMTP Settings For Voicemail'(in the
'Voicemail Settings') have been properly configured before using this feature.
4) Group
·
Pickup Group
If this extension belongs to a pickup group, any calls that ring this extension can
be picked up by other extensions in the same pickup group by dialing the Call
Pickup feature code (default is *4).
www.yeastar.comPage48
MyPBX U5XX Administrator's Guide
Note: *4 is the default setting, it can be changed under Feature Codes ->
General -> Call Pickup.
5) Call Duration Settings
Setup the max cull duration for every call of this extension, but it‟s only valid for
outbound calls. Enter “0” or leave this blank empty, the value would be equal to
the max call duration configured in the Option Settings page.
Note: This setting will not be valid for internal calls.
6) VoIP Settings
·
NAT
This setting should be used when the system is using a public IP address to
communicate with devices hidden behind a NAT device (such as a broadband
router). If you have one-way audio problems, you usually have problems with
your NAT configuration or your firewall's support of SIP and/or RTP ports.
·
Qualify
Send check alive packets to IP phones
·
Enable SRTP
Enable extension for SRTP (RTP Encryption).
·
Transport
This will be the transport method used by the extension. The options are UDP
(default) or TCP or TLS.
·
DTMF Mode – RFC2833, Info, Inband, Auto.
·
Remote Register
Allow to register remote extensions.
If you enable “Remote Register”, the extension password must include
uppercase letters, lowercase letters, and digits.
This option is used to enhance the system security, it‟s disabled by default.
More details for the system security configuration, please refer to APPENDIX B
MyPBX Security Configuration Guide
Other Options
www.yeastar.comPage49
MyPBX U5XX Administrator's Guide
Figure 6-7 VOIP Extension Other Settings
7) Other Options
.Call Waiting
Check this option if the extension should have Call Waiting capability.If this
option is checked, the „When busy‟ follow me options will not be available. The
call waiting function of IP phone has higher priority than MyPBX‟s call waiting
function.
.DND
Don‟t Disturb. When DND is enabled for an extension, the extension will be not
available.
.User Web Interface
Check this option to allow the user to login to the MyPBX User Web interface,
which can be used to check voicemail and extension recordings. Users may login
MyPBX User Web interface by using their extension number and voicemail PIN #
as the login and password respectively.
www.yeastar.comPage50
MyPBX U5XX Administrator's Guide
.Ring Out
Check this option if you want to customize the ring time. Ring tone will stop over
the time defined.
8) Follow me (Call Forwarding)
Call forwarding for an extension can be configured here. The administrator can
configure FollowMe option for this extension. If you want to transfer the call to
an outbound number, please follow the dial pattern of outbound route filled in
the outbound number.
For example: transferring to your mobile phone number 123456789, the dial
pattern of outbound route is „9.‟, you should fill in 9123456789 here.
9) IP Restriction
·
Enable IP Restriction
Check this option to enhance the VoIP security for MyPBX.If this option is
enabled, only the permitted IP/Subnet mask will be able to register this
extension number. In this way, the VoIP security will be enhanced.
More details for the system security configuration, please refer to APPENDIX B
MyPBX Security Configuration Guide.
·
Permitted ‘IP address/Subnet mask’
The input format should be „IP address‟+‟/‟+‟Subnet mask‟.
e.g."192.168.5.100/255.255.255.255" means only the device whose IP
address is 192.168.5.100 is allowed to register this extension number.
e.g."192.168.5.0/255.255.255.0" means only the device whose IP address is
192.168.5.XXX is allowed to register this extension number.
10) Mobility Extension
MyPBX allows you to use your mobile phone as extension. If you set your mobile
phone as mobility extension and then you call MyPBX with this mobility phone,
you will hear a dial tone. MyPBX will recognize your call as a call from an
extension. You can dial the number of other extensions (Your caller ID will be
the number of your extension) or dial out via outbound routes just like dialing
from your extension.
Note: If callback is enabled in the inbound route, the mobility extension
function of this inbound route will be disabled.
11) Spy Settings
MyPBX allows extension to monitor/barge in other conversation. Once this
feature is enabled, the extension has the ability to monitor/barge in other calls
using the feature codes for each spy mode, refer to 'Feature Codes' page for
more information.
www.yeastar.comPage51
MyPBX U5XX Administrator's Guide
·
spy modes
There are 4 spy modes available for choice:
General spy: you have the permission to use the following 3 modes.
Normal spy: you can only hear the call, but can't talk
Whisper spy: you can hear the call, and can talk with the monitored extension
Barge spy: you can hear the call and talk with them both
Note: for example,if 500 want to monitor extension 501, we need to enable the
'allow being spied ' for 501, and choose the spy mode for extension 500.
Then pick up 500 and dial “feature codes + 501” to start monitoring when 501
is in a call
If 500 choose „normal spy‟, it should dial‟*90501‟ to start monitoring;
If 500 choose „whisper spy‟, it should dial „*91501‟ to start monitoring;
If 500 choose „barge spy‟, it should dial „*92501‟ to start monitor;
If 500 choose „general spy‟, it can dial „*90501‟,‟*91501‟ or „*92501‟ to start
monitor.
6.1.2 Phone Provisioning
The Auto Provision sub menu provides users a method to Auto Provision IP
Phone after the Express Setup process.
Note: Auto Provision functions fully test with these models:
Yealink (T12, T18, T20, T22, T26, T28, T32, T38, VP530, VP-2009)
Snom (300, 320, 360, 370)
Snom (300, 320, 360, 370)
Polycom (IP 6000, IP 7000, IP 32X, IP33X, IP430, IP450, IP550, IP560,
VVX1500)
Cisco (IP7940, IP7960)
Aastra(9480i, 9480i-CT, 6730i, 6731i, 6753i, 6755i, 6757i, 6757i CT, 6737i)
GrandStream(GXP1450, GXP2100, GXP2110, GXP2120)
Escene(ES220, ES320, ES330, ES410, ES620)
Fanvil(C56, C58, C60, C62)
News:
When provisioning Yealink, Grandstream, Fanvil, Snom IP phone,
MyPBX is not needed to be set as the only DHCP server any more.
www.yeastar.comPage52
MyPBX U5XX Administrator's Guide
Figure 6-8 Phone Provisioning Page
6.1.2.1 General Settings for Yealink
In this page, you can configure it before provisioning Yealink IP phones,
including the items like general preferences, codecs, remote phone book and
firmware upgrade.
Note: if firmware download server is enabled, IP phone will update the firmware
automatically according the version and server you have configured during the
provision process.
Figure 6-9 General Settings for Yealink
6.1.2.2 Aastra General Settings
In this page, you can configure it before provisioning Aastra IP phones,
including the items like general preferences, program keys configuration, soft
keys configuration.
www.yeastar.comPage53
MyPBX U5XX Administrator's Guide
Figure 6-10 General Setting for Aastra
6.1.2.3 Phone book
You can add your contacts here and when you use phone provisioning, IP phone
will download the phone book.
Figure 6-11 Phone Book
1) Add Contact
·
Type
There are three types: None, VIP and Deny list (Blacklist).
·
Group
There are 5 groups: None, Friends, Family, Work, Colleagues list.
·
Nick Name
You can set a nick name for this number.
·
Favorite
Only works with snom phone.
·
Organization
Input the organization of this contact. Only works with snom phone.
www.yeastar.comPage54
MyPBX U5XX Administrator's Guide
·
Title
Input the title of this contact. Only works with snom phone.
·
Email
Input the email of this contact. Only works with snom phone.
·
Birthday
Input the birthday of this contact. Only works with snom phone.
·
First Name
Input the first name of this contact. Only works with snom phone.
·
Family Name
Input the family of this contact. Only works with snom phone.
·
Office Number
Input the office number here
·
Mobile Number
Input the mobile number here
·
Home Number
Input the home number here
·
Sub Number
Add sub number of this contact. Only works with snom phone.
·
Note
Take some note of this contact. Only works with snom phone.
www.yeastar.comPage55
MyPBX U5XX Administrator's Guide
Figure 6-12 Add a Contact
2) Upload Phonebook
You can upload a phonebook before auto provision, which will be provisioned to
the IP phone when using auto provision feature to configure your IP phones. The
format of phonebook should be *.xml.
Note: All the existing phonebooks of the IP phone will be replaced automatically
if the phonebooks are configured in this way.
6.1.2.4 Configure phone
Let's take provisioning Yealink as an example.
Create New Phone have two modes,
Create New phone in webpage and Upload the IP Phone‟s configure file.
Add new phone via webpage
Click “Add Phone” and fill in the corresponding information in the pop-up
window.
www.yeastar.comPage56
MyPBX U5XX Administrator's Guide
Figure 6-13 Configure Yealink T28
1) General
·
Enabled
Choose yes or no to enable or disable this extension
·
New Config
If your IP phone‟s firmware version is above x.70.x.x, you should select “Yes”.
Or else, it should be “No”.
·MAC address
Input the MAC address of IP phone
·
Name
Put the name of this Phone here.
·
Manufacturer
You can choose the Manufacturer of IP phone
·
Phone Type
Choose the model of your phone. Only for snom phone
www.yeastar.comPage57
MyPBX U5XX Administrator's Guide
·
Call Waiting
This call feature allows your phone to accept other incoming calls to an
extension already in an active call.
·
Key as Send
Configure the key as send, you choose # ,* or disable it
·
Auto redial
Enable the auto redial for IP Phone
·
Auto answer
Configure if auto answer is allowed for IP phone
·
Phone book
Enable the feature of phone book of IP phone
·
Line
You can set each line of IP phone for the account you want, active or not.
Extension: Selected the extension number for IP Phone.
Label: It is shown on the LCD for users to identify the account.
Line Active: You can choose on/off to enable/disable the account respectively.
2) Codecs
In this page, we can set the codecs for IP phone.
Figure 6-14 Select the Codec
www.yeastar.comPage58
MyPBX U5XX Administrator's Guide
3) Memory key settings
In this page, we can configure the DSS keys of IP phone one by one.
Figure 6-15 Configure Memory Key
4) Line keys settings
We can configure the line key settings for this IP phone
Figure 6-16 Configure Line Key
www.yeastar.comPage59
MyPBX U5XX Administrator's Guide
6.1.2.4 Not configured phone
In this section, MyPBX will scan all the supported IP phones and display here, we
can click the 'MAC address' of IP phone and input the corresponding information
in the pop-up window, like figure 6-13.
Figure 6-17 Not Configured Phone List
6.1.2.5 Upload a file
Click “Upload a file” and choose the configure file of IP phone in the popup
window.
Note: the file format must be
Yealink: .cfg file
Snom: .htm file
Grandstream: .xml file
Please edit the configuration files in advance before uploading.
Figure 6-18 Upload Configuration File
www.yeastar.comPage60
MyPBX U5XX Administrator's Guide
6.2 Trunks
6.2.1 Physical Trunk
Multi
physical
trunks
are
supported
in
MyPBXU5XX,
like
E1,
BRI,PSTN,GSM/UMTS. There will be 2 E1 ports fixed inside,for other trunks,
please make sure you have installed the modules inside, BRI trunk requires B2
module, PSTN trunk requires the O2, while GSM/UMTS trunk needs to install the
GSM/UMTS modules inside.
Note:
E1/T1/J1 trunk in MyPBX U5XX
number of
E1/T1/J1
MyPBX U500
MyPBX U510
MyPBX U520
0
1
2
Figure 6-19 Physical Trunk List
E1/T1 trunk
In this page we can configure the details of E1 trunk, before configuring
anything, please make sure the cable is fine, and you have got enough
information from the ISDN provider.
www.yeastar.comPage61
MyPBX U5XX Administrator's Guide
Figure 6-20 E1 Trunk
On the Physical Trunk page, click „Edit‟ on the selected trunk and modify its
properties in the popup window:
Figure 6-21 Edit E1 Trunk
·Trunk name
Set the trunk name
·
Signaling
PRI-NET, PRI-CPE,MFC/R2,SS7
·
Mode Type
E1 / T1 / J1
·
Switch Type
www.yeastar.comPage62
MyPBX U5XX Administrator's Guide
national: National ISDN type2 (common in the US)
ni1: National ISDN type 1
dms100: Nortel DMS100
4ess: AT&T 4ESS
5ess: Lucent 5ESS
euroisdn: EuroISDN
qsig: Minimalistic protocol to build a "network" with two or more PBX of different
vendors!
·
PRI Dial Plan
Sets an option required for some (rare) switches that require a dial plan
parameter to be passed. This option is ignored by most PRI switches. It may be
necessary on a few pieces of hardware. This option can almost always be left
unchanged from the default.
·
Reset interval
Set the time in seconds between restart of unused channels. Some PBXs don't
like channel restarts. so set the interval to a very long interval e.g. 100000000
or 'never' to disable *entirely*. If you are in Israel, the following is important:
As Bezeq in Israel doesn't like the B-Channel resets happening on the lines, it is
best to set the reset interval to 'never' when installing a box in Israel. Our past
experience also shows that this parameter may also cause issues on local
switches in the UK and China.
·
PRI Local Dial Plan
Sets an option required for some (rare) switches that require a dial plan
parameter to be passed. This option is ignored by most BRI switches. It may be
necessary on a few pieces of hardware. This option can almost always be left
unchanged from the default.
·
Over Lap Dial
Define whether MyPBX can dial this switch using overlap digits. If you need
Direct Dial-in (DDI; in German "Durchwahl") you should change this to yes, then
MyPBX will wait after the last digit it receives.
·
PRI Indication
Tells how Device should indicate Busy() and Congestion() to the switch/user.
Accepted values are:
inband: Device plays indication tones without answering; not available on all
PRI/BRI subscription lines .
outofband: Device disconnects with busy/congestion information code so the
switch will play the indication tones to the caller. Busy() will now do same as
setting PRI_CAUSE=17 and Hangup().
www.yeastar.comPage63
MyPBX U5XX Administrator's Guide
·
Facility Enable
To enable transmission of facility-based ISDN supplementary services (such as
caller name from CPE over facility).
·
NSF
Used with AT&T PRIs.If outbound calls are being rejected due to "Mandatory
information element missing" and the missing IE is 0x20, then you need this
setting.
·
CRC
CRC Verification.
·
Codec
Default ,A-Law,U-Law.
·
Echo Cancellation
Obviously this disables or enables echo cancellation, it is recommended to not
turn this off.
1) CallerID Prefix
·
International Prefix
When there are international calls coming in via this BRI trunk, the International
Prefix you have set here will be added before the CID. So you can know this is
an international call before you answer it.
·
National Prefix
When there are national calls coming in via this BRI trunk, the National Prefix
you have set here will be added before the CID. So you can know this is a
national call before you answer it.
·
Local Prefix
When there are Local calls coming in via this BRI trunk, the Local Prefix you have
set here will be added before the CID. So you can know this is a local call before
you answer it.
·
Private Prefix
When there are Private calls coming in via this BRI trunk, the Private Prefix you
have set here will be added before the CID. So you can know this is a Private call
before you answer it.
·
Unknown Prefix
www.yeastar.comPage64
MyPBX U5XX Administrator's Guide
When there are calls with unknown number coming via this BRI trunk, the
Unknown Prefix you set here will be shown as the caller ID.
2) DOD Setting
DOD (Direct Outward Dialing) means the caller ID displayed when dialing out,
before configure this, please make sure the provider supports this feature
·
Global DOD
Global direct outward dialing number.
·
DOD
Direct Outward Dialing Number.
·
Associated Extension
The extension make call out via BRI Trunk will display the associated DOD.
BRI Trunk
Basic Rate Interface (BRI, 2B+D, 2B1D) is an Integrated Services Digital
Network (ISDN) configuration intended primarily for use in subscriber lines
similar to those that have long been used for plain old telephone service. The
BRI configuration provides 2 bearer channels (B channels) at 64 kbit/s each and
1 data channel (D channel) at 16 kbit/s. The B channels are used for voice or
user data, and the D channel is used for any combination of data,
control/signalling, and X.25 packet networking
Figure 6-22 BRI Trunk
Click edit to configure the details of BRI trunks
www.yeastar.comPage65
MyPBX U5XX Administrator's Guide
Figure 6-23 Edit BRI Trunk
·
Trunk Name
A unique label used to identify this trunk when listed in outbound rules,
incoming rules, etc. E.g.“BriTrunk1”
·
Signaling
Signaling method
BRI-CPE: ISDN BRI in TE mode and Point to Point.
BRI-CPE-PTMP: ISDN BRI in TE mode and Point to multi Point.
BRI-NET: ISDN BRI in NET mode and Point to Point.
BRI-NET-PTMP: ISDN BRI in NET mode and Point to multi Point.
·
Switch Type
National: National ISDN type2 (common in the US)
ni1: National ISDN type 1
dms100: Nortel DMS100
4ess: AT&T 4ESS
5ess: Lucent 5ESS
euroisdn: EuroISDN
qsig: D-channel signaling protocol at Q reference point for PBX networking .
www.yeastar.comPage66
MyPBX U5XX Administrator's Guide
·
PRI Dial Plan
Sets an option required for some (rare) switches that require a dial plan
parameter to be passed. This option is ignored by most BRI switches. It may be
necessary on a few pieces of hardware. This option can almost always be left
unchanged from the default.
·
Reset interval
Sets the time in seconds between restart of unused channels. Some PBXs don't
like channel restarts. so set the interval to a very long interval e.g. 100000000
or 'never' to disable *entirely*. If you are in Israel, the following is important:
As Bezeq in Israel doesn't like the B-Channel resets happening on the lines, it is
best to set the reset interval to 'never' when installing a box in Israel. Our past
experience also shows that this parameter may also cause issues on local
switches in the UK and China.
·
PRI Local Dial Plan
Sets an option required for some (rare) switches that require a dial plan
parameter to be passed. This option is ignored by most BRI switches. It may be
necessary on a few pieces of hardware. This option can almost always be left
unchanged from the default.
·
Over Lap Dial
Whether MyPBX can dial this switch using overlap digits. If you need Direct
Dial-in (DDI; in German "Durchwahl") you should change this to yes, then
MyPBX will wait after the last digit it receives.
·
PRI Indication
Tells how Device should indicate Busy() and Congestion() to the switch/user.
Accepted values are:
inband: Device plays indication tones without answering; not available on all
PRI/BRI subscription lines .
outofband: Device disconnects with busy/congestion information code so the
switch will play the indication tones to the caller. Busy() will now do same as
setting PRI_CAUSE=17 and Hangup().
·
Enable Facility
To enable transmission of facility-based ISDN supplementary services (such as
caller name from CPE over facility).
·
NSF
Used with AT&T PRIs.If outbound calls are being rejected due to "Mandatory
information element missing" and the missing IE is 0x20, then you need this
setting.
www.yeastar.comPage67
MyPBX U5XX Administrator's Guide
·
Echo Cancellation
Obviously this disables or enables echo cancellation, it is recommended to not
turn this off.
·
Hide CallerID
If you want others to see your CID, please disable this option.
·
Codec
You can choose alaw or ulaw codes.
1) CallerID Prefix
·
International Prefix
When there are international calls coming in via this BRI trunk, the International
Prefix you have set here will be added before the CID. So you can know this is
an international call before you answer it.
·
National Prefix
When there are national calls coming in via this BRI trunk, the National Prefix
you have set here will be added before the CID. So you can know this is a
national call before you answer it.
·
Local Prefix
When there are Local calls coming in via this BRI trunk, the Local Prefix you have
set here will be added before the CID. So you can know this is a local call before
you answer it.
·
Private Prefix
When there are Private calls coming in via this BRI trunk, the Private Prefix you
have set here will be added before the CID. So you can know this is a Private call
before you answer it.
·
Unknown Prefix
When there are calls with unknown number coming via this BRI trunk, the
Unknown Prefix you set here will be shown as the caller ID.
2)DOD Setting
·
Global DOD
Global direct outward dialing number.
·
DOD
Direct Outward Dialing Number.
·
Associated Extension
The extension make call out via BRI Trunk will display the associated DOD.
www.yeastar.comPage68
MyPBX U5XX Administrator's Guide
PSTN trunk
The public switched telephone network (PSTN) is the network of the world's
public circuit-switched telephone networks
Figure 6-24 PSTN Trunk
Click edit to configure more details
Figure 6-25 Edit PSTN Trunk
·
Trunk Name
A unique label used to identify this trunk when listed in outbound rules,
incoming rules, etc. E.g.“pstn5”
·
Volume Setting
Used to modify the volume level of this trunk. Normally, this setting does not
need to be changed.
www.yeastar.comPage69
MyPBX U5XX Administrator's Guide
1)Busy Detection
·
Busy Detection
Busy Detection is used to detect far end hang-up or for detecting a busy signal.
Select “Yes” to turn this feature on.
·
Busy Count
If Busy Detection is enabled, it is also possible to specify how many busy tones
to wait for before disconnecting the call. The default is 4, but better results can
be achieved if set to 6 or even 8. Remember, the higher the number, the more
time will be required to release a channel. A higher setting lowers the
probability that you will encounter random hang-ups.
·
Busy Interval
The busy detection interval
·
Busy Pattern
If Busy Detection is enabled, it is also possible to specify the cadence of your
busy signal. In many Countries, it is 500msec on, 500msec off. Without Busy
Pattern specified, MyPBX will accept any regular sound-silence pattern that
repeats <Busy Count> times as a busy signal. If you specify Busy Pattern, then
MyPBX will further check the length of the tone and silence, which will further
reduce the chance of a false positive disconnect.
·
Frequency Detection
Used for Frequency Detection (Enable detecting the busy signal frequency or
not).
·
Busy Frequency
If the Frequency Detection is enabled, you must specify the local frequency.
·
Polarity Detection
Configure if the call needs to be hung up when a polarity signal arrived
2)Advanced Options
·
Caller ID Start
This option allows you to define the start of a Caller ID signal:
Ring:Start when a ring is received (Caller ID Signaling: Bell_USA, DTMF).
Polarity: Start when a polarity reversal is started (Caller ID Signaling:
V23_UK,V23_JP,DTMF).
Before Ring:Start before a ring is received (Caller ID Signaling: DTMF).
·
Caller ID Signaling
This option defines the type of Caller ID signaling to use. It can be set to one of
the following:
Bell: bell202 as used in the United States
www.yeastar.comPage70
MyPBX U5XX Administrator's Guide
v23_UK: suitable in the UK
v23_Japan: suitable in Japan
v23-Japan pure: suitable in Japan
DTMF: suitable in Denmark, Sweden, and Holland
.Caller ID Detection
For fxo trunks, this option forces MyPBX to clarify Caller ID incoming calls
GSM/UMTS Trunk
GSM/UMTS trunks are supported in MyPBXU5XX if you have got the GSM/UMTS
module and SIM cards installed. One GSM/UMTS trunks support only one SIM
card for one concurrent call.
Figure 6-26 GSM/UMTS Trunk
Click edit to configure more details.
Figure 6-27 Edit GSM/UMTS Trunk
Trunk Name
A unique label used to identify this trunk when listed in outbound rules,
incoming rules, etc. E.g.“GSM9”
·
Volume Setting
Used to modify the volume level of this trunk. Normally, this setting does not
need to be changed.
·
Pin Code
Please enter your SIM card pin code here if your card has a pin code
www.yeastar.comPage71
MyPBX U5XX Administrator's Guide
6.2.2 VoIP Trunk
There are two types of VOIP trunk in MyPBX: SIP and IAX, in this page, we can
also configure the „service provider‟ trunk, which doesn‟t need the use name
and password for authorization, when you have bought a trunk from provide
with IP address only, please choose „service provider‟ trunk .
Figure 6-28 VOIP Trunk
6.2.2.1 VoIP Trunk
In this page, we can configure VoIP trunk (SIP/ IAX) you have got from provider
with the authorization name and password.
Figure 6-29 VOIP Trunk
1)
Add VoIP Trunk
Input correct SIP information (provide by VoIP provider). Inaccurate
information will prevent the trunk from registering.
www.yeastar.comPage72
MyPBX U5XX Administrator's Guide
Figure 6-30 Add a SIP Trunk
·
Type
SIP – Identifies whether the trunk sends and receives calls using the VoIP
protocol SIP
·
Provider Name
A unique label to help you identify this trunk when listed in outbound rules,
incoming rules etc. E.g.“yeastar”
·
Hostname/IP
Service provider‟s hostname or IP address.5060 is the standardport number
used by SIPprotocol. Don‟t change this part if it is not required.
.Domain
VoIP provider‟s server domain name.
www.yeastar.comPage73
MyPBX U5XX Administrator's Guide
·
Username
Username of SIP account. Used for SIP trunk registration.
.Authorization name
Used for SIP authentication. Leave this blank if not required.
·
Password
Password of SIP account.
.From User
All outgoing calls from this SIP Trunk will use the From User (In this case the
account name for SIP Registration) in From Header of the SIP Invite package.
Keep this field blank if not needed
.Online number
Define the online number that expected by „Skype Connect‟ and some other SIP
service providers. Leave this field blank if not needed.
·
Maximum Channels
Control the maximum number of outbound channels (simultaneous calls) that
can be used on this trunk. Inbound calls are not counted against the maximum.
Set as 0 to specify no maximum.
·
Caller ID
Specify the caller ID to use when making outbound calls over this trunk. The
caller ID set in the „extension‟ screen will override the caller ID set in the „VOIP
trunk‟ screen. Please note that not all the service providers support this feature.
Contact your service provider for more information.
·
Outbound Proxy Server
A proxy that receives requests from a client, even though it may not be the
server resolved by the Request-URI.
·
Realm
Realm is a string to be displayed to users so they know which username and
password to use.
·
Codecs
Define the codec for this sip trunk and its priority
Note: To change the codec type and priority of this trunk, please create it first,
it will appear when you edit it again.
·
Transport
www.yeastar.comPage74
MyPBX U5XX Administrator's Guide
This will be the transport method used by the SIP Trunk. This method is given by
the SIP trunk provider. The options are UDP (default) or TCP or TLS.
·
Enable SRTP
Define if SRTP is enabled for this trunk
·
Qualify
Send check alive packets to the sip provider.
·
DTMF mode
Set default mode for sending DTMF of this trunk.Default setting: rfc2833
·
DOD
DOD (Direct Outward Dialing) means the caller ID displayed when dialing out,
before configure this, please make sure the provider supports this feature
·
Associated Extension
The extension make call out via SIP Trunk will display the associated DOD
2) Add IAX trunk
Input correct IAX information (provided by VOIP provider). Inaccurate
information will prevent the trunk from registering.
Figure 6-31 Add an IAX Trunk
www.yeastar.comPage75
MyPBX U5XX Administrator's Guide
·
Type
IAX – Identifies whether the trunk sends and receives calls by using the VoIP
protocol IAX.
·
Provider Name
A unique label to help you identify this trunk when listed in outbound rules,
incoming rules etc. E.g.“yeastar2”
·
Hostname/IP
Service provider‟s hostname or IP address. 4569 is the standardport number
used by IAX protocol. Don‟t change this part if it is not required.
·
Username
Username of IAX account; Used for IAX trunk registration.
·
Password
Password of IAX account
.Online number
Define the online number that expected by „Skype Connect‟and some other SIP
service providers. Leave this field blank if it's no required.
·
Maximum Channels
Control the maximum number of outbound channels (simultaneous calls) that
can be used on this trunk . Inbound calls are not counted against the maximum.
Set as 0 to specify no maximum.
·
Caller ID
Specify the caller ID to use when making outbound calls over this trunk. The
caller ID set in the „extension‟ screen will override the caller ID setting in the
„VOIP trunk‟ screen. Please note that not all the service providers support this
feature. Contact your service provider for more information.
·
DOD
DOD (Direct Outward Dialing) means the caller ID displayed when dialing out,
before configure this, please make sure the provider supports this feature
·
Associated Extension
The extension make call out via IAX Trunk will display the associated DOD
6.2.2.2 Service Provider
This is service provider trunk (peer to peer mode), which authorized using IP
www.yeastar.comPage76
MyPBX U5XX Administrator's Guide
address only. If you have got a trunk with IP address only, please choose this
type
Figure 6-32 Service Provider Trunk
·
Type
SIP or IAX
SIP – Identifies whether the trunk sends and receives calls by using the VoIP
protocol SIP.
IAX - Identifies whether the trunk sends and receives calls by using the VoIP
protocol IAX.
·
Provider Name
A unique label would help to you identify this trunk. E.g.“Provider2”
·
Hostname/IP
Service provider‟s hostname or IP address.
Note: 5060 is the standard port number used by SIP protocol, 4569 is the
standard port number used by IAX protocol. Don‟t change this part if it is not
required.
·
Maximum Channels
Control the maximum number of outbound channels (simultaneous calls) that
can be used on this trunk. Inbound calls are not counted against the maximum.
Leave blank to specify no maximum.
www.yeastar.comPage77
MyPBX U5XX Administrator's Guide
·
Codecs
Define the codec for this sip trunk and its priority
Note: codec can only display when edit it after creating the trunk.
·
Transport
This will be the transport method used by the SIP Trunk. This method is given by
the SIP trunk provider. The options are UDP (default) or TCP or TLS.
·
Qualify
Send check alive packets to the sip provider.
·
DTMF mode
Set default mode for sending DTMF of this trunk. Default setting: rfc2833
·
DOD
DOD (Direct Outward Dialing) means the caller ID displayed when dialing out,
before configure this, please make sure the provider supports this feature
·
Associated Extension
The extension make call out via this Trunk will display the associated DOD.
www.yeastar.comPage78
MyPBX U5XX Administrator's Guide
6.3 Outbound Call Control
6.3.1 Outbound Routes
In this page, we can configure the outbound rules to control the outgoing calls.
Notes:
1. The max number of outbound route is 64.
2. If the dial patterns are the same in several routes, MyPBX will choose the
available routes from top to the last one.
3. When you have created a new extension, please edit the outbound route so
that he can dial out too
Figure 6-33 Outbound Route Page
We can create outbound route or use the default route “pstnout” (dial
9+numbers to dial out)
www.yeastar.comPage79
MyPBX U5XX Administrator's Guide
Figure 6-34 Add/Edit Outbound Route
·
Route Name
Name of this Outbound Route. E.g. “Local” or “Long Distance”.
·
Dial Pattern
Outbound calls that match this dial pattern will use this outbound route. There
are a number of dial pattern characters that have special meanings:
X : Any Digit from 0-9
Z : Any Digit from 1-9
N : Any Digit from 2-9
[12345-9] : Any digit in the brackets (in this example, 1,2,3,4,5,6,7,8,9)
The “.” Character will match any remaining digits. For example, “9011.” will
match any phone number that starts with “9011”, excluding “9011” itself.
The “!” will match none remaining digits, and causes the matching process to
www.yeastar.comPage80
MyPBX U5XX Administrator's Guide
complete as soon as it can be determined that no other matches are possible.
Example 1: NXXXXXX will match any 7 digits phone number.
Example 2: 1NXXNXXXXX will match a phone number starting with a 1,
followed by a 3-digit area code, and then 6 digit number.
·
Strip digits from front
Allows the user to specify the number of digits that will be stripped from the
front of the phone number before the call is placed. For example, if users must
press 0 before dialing a phone number, one digit should be stripped from the
dial string before the call is placed.
·
Prepend these digits before dialing
These digits will be prepended to the phone number before the call is placed. For
example, if a trunk requires 10 digit dialing, but users are more comfortable
with 7 digit dialing, this field could be used to prepend a 3 digit area code to all
7 digit phone numbers before calls are placed.
·
Password
The route password can be used to protect this route from being accessed
without a password.
·
T.38 Support:
Enable T38 fax in this outbound route (Only for SIP Trunk).
·
Rrmemory Hunt
Round robin with memory, remembers which trunk was used last time, and then
use the next available trunk to call out.
·
Office Hours
When a specific office hour is selected, this outbound route can only be used
during this office hour, and can‟t be used in non-office hours.
·
Member Extensions
Defines the extensions that will be permitted to use this outbound route.
·
Member Trunks
Defines the trunks that can be used for this outbound route.
www.yeastar.comPage81
MyPBX U5XX Administrator's Guide
6.3.2 Speed Dial Settings
Figure 6-35 Speed Dial Page
1) Options
·
The prefix of speed dial
The prefix should be dialed before the speed dial number. Default is *99
Figure 6-36 Speed Dial Settings
2) Add new speed dial.
·
Source Number
The speed dial number.
·
Destination Number
The number you want to call.
E.g. The source number is ”123”. The destination number is 5503305.The prefix
number is *99.You can use an extension with any type to dial *99123, then it
will call to number 5503305.
Note: Don‟t forget to add the outbound dial prefix if you would like to dial the
speed dial number through trunk.
www.yeastar.comPage82
MyPBX U5XX Administrator's Guide
6.4 Inbound Call Control
In this page, we can configure the details of IVR, ring group, queue and inbound
routes.
6.4.1 IVR
When there‟s an inbound call aims at Auto Attendant, MyPBX will play an IVR
recording and route the caller to the requested destination (for example,
„Welcome to XX company, for sales press 1, for technical support press 2, for
operator press 0, etc‟). The system will transfer the call to corresponding
extension according to DTMF digits inputted by the user
Figure 6-37 IVR Page
There is a default IVR here, we can edit it directly or add IVR by yourself
www.yeastar.comPage83
MyPBX U5XX Administrator's Guide
Figure 6-38 IVR Settings
·
Number
MyPBX treats IVR as an extension; you can dial this extension number to reach
the IVR from internal extension.
·
Name
A name for the IVR
·
Prompt
The prompt recording that will be played when this IVR is reached.
·
Repeat Count
The number of times that the selected IVR prompt will be played.
·
Key Timeout
Wait for the user to enter a new extension for a specified number of seconds.
www.yeastar.comPage84
MyPBX U5XX Administrator's Guide
·
Enable Direct Dial
Allow the caller to dial other extensions number directly.
·
Key Press Events
A list of actions that can be performed depending on the digit dialed by the user.
·
Key
The Key pressed when the callers hear the IVR prompt.
·
Action
When the callers press the corresponding key, the action MyPBX executes.
No Action: Do nothing
Connect to Extension: Connect the call to an extension.
Connect to Voicemail: Connect the call to the voicemail of an extension
Connect to RingGroup: Connect the call to a ringgroup.
Connect to IVR: Connect the call to an IVR.
Connect to Conference Room: Connect the call to a conference room.
Connect to DISA: Connect the call to a DISA.
Connect to Queue: Connect the call to a queue.
Connect to Faxes: Connect the call to Faxes of extensions.
Dial by Name: The callers can dial the name of an extension to connect to the
corresponding extension.
Hung up: Hang up the call.
·
Destination
Where will MyPBX route the call when the action occurs.
·
Time Out
Defines the timeout action. A timeout occurs after the IVR prompt has finished
playing for the number of times specified by the 'Repeat Count' field.
·
Invalid
Defines the invalid action. The invalid action is triggered if the user enters
aDTMF digit that is not defined for this IVR.
6.4.2 Ring Groups
Ring groups can be configured to balance the call traffic for multiple users and
give callers a higher level of availability for incoming calls. Multiple ring methods
and voicemail are supported.
Note: follow me feature in extension page will not take effect when it‟s ringing
as an agent.
www.yeastar.comPage85
MyPBX U5XX Administrator's Guide
Figure 6-39 Ringgroup Page
There is a default ringgroup, you can edit it or create a new one
Figure 6-40 Add/Edit Ringgroup
·
Ring Group Name
This option defines a name for this group, i.e. „Sales‟. „Ring Group Name‟ is a
label to help you identify this group in the group list.
·
Ring Group Number
This option defines the numbered extension that can be dialed to reach this
group.
·
Strategy
This option sets the Ringing Strategy for this Group. The options are as follows:
1. RingAll Simultaneously: Ring all available Extensions simultaneously.
2. Ring Sequentially: Ring each extension in the group one at a time.
·
Seconds to ring each member
1. If the strategy is „RingAll Simultaneously‟, it means set the number of
www.yeastar.comPage86
MyPBX U5XX Administrator's Guide
seconds to ring this group before routing the call according to the „Destination if
No Answer‟ settings.
2. If the strategy is „Ring Sequentially‟, it means set the number of seconds to
ring a single extension before moving onto the next one.
·Ring Group Members
An extension can be made a member of this ring group by moving it into the
„Selected‟ box.
·
Destination If No Answer
When all members on this group fail to answer the call, system will handle the
call according to the selected destination.
6.4.3 Queues
Call Queues give users (i.e. call centers) an efficient means to have their calls
answered in the order they were received to deliver top tier customer service.
Figure 6-41 Queue Page
Call queues allow calls to be sequenced to one or more agents.
Notes:
1. Dial 'Queue number + '*'' to log in or 'Queue number + '**'' to log out the
queue. For example, if the queue number is '680', then agent can dial '680*'
to log in or '680**' to log out.
2. Follow me feature in extension page will not take effect when it‟s ringing as
an agent of queue
www.yeastar.comPage87
MyPBX U5XX Administrator's Guide
Figure 6-42 Add/Edit Queue
·
Queue Name
A name for the Queue.
www.yeastar.comPage88
MyPBX U5XX Administrator's Guide
·
Queue Number
Use this number to dial into the queue, or transfer callers to this number to put
them into the queue.
·
Queue Password
You can require agents to enter a password before they can login to this queue.
·
Queue Agent Timeout
The number of seconds an agent's phone can ring before we consider it a
timeout.
·
Queue Max Wait Time
The maximum number of seconds a caller can wait in a queue before being
pulled out. (0 for unlimited).
·
Queue Ring Strategy
This option sets the Ringing Strategy for this Queue. The options are
RingAll: Ring all available Agents simultaneously until one answers.
LeastRecent: Ring the Agent which was least recently called.
FewestCalls: Ring the Agent with the fewest completed calls.
Random: Ring a Random Agent.
RRmemory: Round Robin with Memory, Remembers where it left off in the last
ring pass.
1) Agents
This selection shows all users. Selecting a user here makes them an agent of the
current queue.
2) Caller Position Announcements
·
Announce Position
Announce position of caller in the queue
·
Announce Hold Time
Enabling this option causes MyPBX to announce the hold time to the caller
periodically based on the frequency timer. Either yes or no; hold time will not be
announced if <1 minute.
·
Frequency
How often to announce queue position and estimated hold time.
Note: '0 seconds' means disable the announcement.
3) Periodic Announcements
·
Prompt
Select a prompt file to play periodically.
www.yeastar.comPage89
MyPBX U5XX Administrator's Guide
·
Frequency
How often to announce a prompt to the caller.
4) Events
If a caller presses the key while waiting in the queue, this setting selects which
action should process the key press.
5) Failover-Destination
Defines the failover action. A failover occurs after the user reach the Queue max
wait time.
6) Others
·
Music On Hold
Select the 'Music on Hold' Class for this Queue.
·
Leave When Empty
This option controls whether callers already on hold are forced out of a queue
that has no agents. There are two options.
Yes: Callers are forced out of a queue when no agents are logged in.
No: Callers will remain in a queue with no agents.
·
Join Empty
This option controls whether callers can join a call queue that has no agents.
There are two options,
Yes: Callers can join a call queue with no agents or only unavailable agents
No: Callers cannot join a queue with no agents
The default option is No.
·
Agent Announcement
Announcement played to the Agent prior to bridging in the caller.
·
Join Announcement
Announcement played to callers once prior to joining the queue.
·
Retry
The number of seconds we wait before trying all the phones again.
·
Wrap-up time
How many seconds after the completion of a call an Agent will have before the
Queue can ring them with a new call. The default is 30.
www.yeastar.comPage90
MyPBX U5XX Administrator's Guide
6.4.4 Conferences
Figure 6-43 Conference Room List
Conference Calls increase employee efficiency and productivity, and provide a
more cost-effective way to hold meetings. Conference agents can dial * to
access to the settings options and the admin can kick the last user out and can
lock the conference room.
·
Extension
This is the number dialed to reach this Conference Room.
·
Admin
Admin can kick a user out and can lock the conference room.
·
Pin #
Set a PIN # that must be entered in order to access this conference room (i.e.
1234).
Figure 6-44 Add/Edit Conference Room
www.yeastar.comPage91
MyPBX U5XX Administrator's Guide
6.4.5 Inbound Routes
Inbound routing processes incoming call traffic to destination extensions during
office hours or outside office hours
Figure 6-45 Inbound Route List
There is a default inbound route for all the trunks and set IVR as the destination,
you can edit it or create a new one for your demands. When an incoming call
arrives, the system will first check „fax detection‟, then „Holidays‟, at last
„Business Days‟.
www.yeastar.comPage92
MyPBX U5XX Administrator's Guide
figure 6-46 Add/Edit Inbound Route
1) General
·
Route Name
A name for this inbound route. E.g.“pstnin”.
·
DID Number
Define the expected DID Number if this trunk passes DID on incoming calls.
Leave this field blank to match calls with any or no DID info. You can also use
pattern matching to match a range of numbers.The following patterns may be
used:
X: Any Digit from 0-9
Z: Any Digit from 1-9
www.yeastar.comPage93
MyPBX U5XX Administrator's Guide
N: Any Digit from 2-9
[12345-9]: Any digit in the brackets (in this example, 1,2,3,4,5,6,7,8,9)
The „.‟Character will match any remaining digits. For example, 9011. will match
any phone number that starts with 9011, excluding 9011 itself.
The „!‟ will match none remaining digits, and causes the matching process to
complete as soon as it can be determined that no other matches are possible.
Example 1: NXXXXXXwill match any 7 digits phone number.
Example 2: 1NXXNXXXXXwill match a phone number starting with a 1,
followed by a 3-digit area code, and then 6 digit number.
For more information, please refer to AppendixH How to Use DID.
·
Extension
Define the extension for DID number. This field is only valid when you use BRI,
SIP, SPS or SPX trunk for this inbound router. You can only input number and
„-„in this field, and the format can be xxx or xxx-xxx. The count of the number
must be only one or equal the count of the DID number.
·
Caller ID Number
Define the Caller ID Number to be matched on incoming calls. Leave this field
blank to match any or no DID info.
You can also use a pattern match (e.g. 2[345]X) to match a range of numbers.
The following patterns may be used:
X: Any Digit from 0-9
Z: Any Digit from 1-9
N: Any Digit from 2-9
[12345-9]: Any digit in the brackets (in this example, 1,2,3,4,5,6,7,8,9)
The „.‟Character will match any remaining digits. For example, 9011. will match
any phone number that starts with 9011, excluding 9011 itself.
The „!‟ will match none remaining digits, and causes the matching process to
complete as soon as it can be determined that no other matches are possible.
Example 1: NXXXXXX will match any 7 digits phone number.
Example 2: 1NXXNXXXXXwill match a phone number starting with a 1,
followed by a 3-digit area code, and then 6 digit number.
·
Distinctive Ringtone
MyPBX support mapping to custom ring tone files. For example, if you configure
the distinctive ringing for custom ring tone to „Family‟, the ring tone will be
played if the phone receives the incoming call.
·
Enable Callback
You can enable the callback function of this inbound route. If you want to
www.yeastar.comPage94
MyPBX U5XX Administrator's Guide
configure the callback function, please refer to chapter 6.7.4
How do I configure distinctive ring tones? Please refer to APPENDIXF.
Currently distinctive ringtone can be compatible with Yealink and Snom phone.
2) Member Trunks
This area allows you to select which trunks will be member trunks for this route.
To make a trunk a member of this route, please move it to the 'Selected' box.
3) Business Days
Define where the calls will be routed during Business Days.
·
Office Hours
Select one defined business days office hours.
·
Office Hours Destination
Configure where to route the incoming calls during office hours.
·
End Calls
Route the incoming calls to end calls, System will auto hang-up the call.
·
Extension
Route the incoming calls to a specific extension.
·
Voicemail
Route the incoming calls to extension‟s voicemail.
·
IVR
Route the incoming calls to a specific IVR.
·
Ring Group
Route the incoming calls to a specific Ring Group.
·
Conference Room
Route the incoming calls to a specific Conference Room.
·
DISA
Route the incoming calls to a specific DISA.
·
Queues
Route the incoming calls to a specific Queue.
·
Faxes
Route the incoming faxes to a specific extension‟s mail address.
www.yeastar.comPage95
MyPBX U5XX Administrator's Guide
Note: This function only supports T.38 faxes.
·
Outbound Routes
Route the incoming calls to a specific outbound route.
This function is mainly used for the connection of two branches.
For example: Company A locates headquarters in the USA with a branch B in
China. A and B both have MyPBX phone systems.
Now if staff of A would like to make a call to a telephone or mobile phone in
China from the extension of A but via the FXS line of B, that can be done by this
configuration.
·
Non-office Hours Destination
Configure where to route the incoming calls during non-office hours.
4) During Holidays
Define where the calls will be routed during Holidays.
·
Holiday
Select which defined Holiday to use.When a time is defined in both Business
Days and Holidays, it will be treated as Holidays.
·
Destination
Configure where to route the incoming calls during holidays.
5) Fax Detection
Configure if detecting faxes in this inbound route.
Note: Please choose IVR as the destination above before configure fax
detection (recommended)
·
Destination
Configure where the faxes will be routed when faxes are detected.
·
No detect
Do not detect faxes.
·
Custom Email
Customize an E-mail address to receive the faxes. You should first configure the
„Voicemail Settings->SMTP Settings for Voicemail‟ correctly before you use this
option.
·
Faxes
Send faxes to an extension. If choosing a FXS extension here, the fax will be
sent to the FXS port selected, you should connect a fax machine to this FXS port.
www.yeastar.comPage96
MyPBX U5XX Administrator's Guide
If Choosing a VoIP extension, the fax will be sent to the extension‟s voicemail as
an attachment.
Note: If you receive faxes with custom Email address, the „SMTP settings‟ of
„Voicemail Settings‟ should be configured successfully in advance. If you receive
faxes with E-mail address configured in VOIP extension voicemail, you should
first make sure the tested email to your email address works fine.
www.yeastar.comPage97
MyPBX U5XX Administrator's Guide
6.5 Audio Settings
It‟s allowed to customize the prompts in MyPBX, including the Audio In and
change the system prompts to your local country.
6.5.1 Custom Prompts
We can record or upload the prompts in this page; you can also play it directly
to confirm if it‟s a valid one, you can also download it and save it as an backup
Figure 6-47 Custom Prompts List
1. Record new Prompt
Figure 6-48 Record a New Prompt
The administrator can use this screen to record custom prompts by doing the
following:
1) Click “Record New Custom Prompt”
2) Input the desired file name on the popup window and choose an extension to
call for recording (such as 500).
3) Click “Record”. The selected extension will ring and you can pick up the phone
to start recording.
2. Upload Prompt
www.yeastar.comPage98
MyPBX U5XX Administrator's Guide
Figure 6-49 Upload a Prompt
The administrator can also upload prompts by doing the following:
1)Click “Upload Prompt”.
2) Click “Browse” to choose the desired prompt.
3) Click “Upload” to upload the selected prompt.
Note: The file size must not be larger than 1.8 MB, and the file must be WAV
format:
GSM 6.10 8 kHz, Mono, 1 Kb/s;
Alaw/Ulaw 8 kHz, Mono, 1 Kb/s;
PCM 8 kHz, Mono, 16 Kb/s.
6.5.2 Music on Hold Prompts
In this page, we can upload the music on hold prompts.
Figure 6-50 Music on Hold List
The administrator can upload on hold music as follows:
1) Click “Upload Music on Prompt”.
2) Click “Browse” to choose the desired audio file.
3) Click “Upload” to upload the selected file.
www.yeastar.comPage99
MyPBX U5XX Administrator's Guide
Figure 6-51 Upload Music on Hold
Note: The file size must not be larger than 1.8 MB, and the file must be WAV
format:
GSM 6.10 8 kHz, Mono, 1 Kb/s;
Alaw/Ulaw 8 kHz, Mono, 1 Kb/s;
PCM 8 kHz, Mono, 16 Kb/s.
6.5.3 System Prompts Settings
MyPBX have prompts of many languages. You can download the appropriate
language you need. MyPBX can support American English, Australian English,
Chinese, Dutch, French, Canadian French, German, Greek, Hungarian, Italian,
Polish, Portuguese, Brazilian Portuguese, Russian, Spanish, Mexican Spanish,
Turkish, Thai, and Korean currently.
Notes:
1. Auto-detection is highly recommended. But if you prefer to download via
HTTP or TFTP server, please contact the local dealer for the prompts
2. When update successfully, just click “apply the changes” on web then it will
take effect, there is no need to reboot.
Figure 6-52 System Prompts Settings Page
www.yeastar.comPage100
MyPBX U5XX Administrator's Guide
6.6 Basic Settings
There are some basic settings we need to configure MyPBXU5XX,like the general
preferences, business hours, feature codes, voicemail settings.
6.6.1 General Preferences
In this page, there are some general settings of MyPBX.
Figure 6-53 General Settings
1) General
·
Ring Timeout
Number of seconds to ring a device before handling the call as per the
extension‟s Follow Me settings. Default value is 30s.
.MAX call duration
The absolute maximum amount of time permitted for a call. A setting of 0
disables the timeout. Default value is 6000s.
.Maximum concurrent calls
Maximum concurrent calls limits. Default value 0 means no limit
·
Music on hold
Used to set hold music for the system.
www.yeastar.comPage101
MyPBX U5XX Administrator's Guide
·
Tone Region
Please select your country or nearest neighboring country to enable the default
dial tone, busy tone, and ring tone for your region.
Note: please reboot the system to take effect.
·
HTTP bind port/Web Access Port
Port to use for HTTP sessions; Default: 80
Note: please reboot the system to take effect.
·
FXO Mode
FXO port‟s operation mode.
·
Virtual Ring Back Tone
It‟s only for GSM/UMTS /UMTS trunk. Once enabled, when the caller call out
with GSM/UMTS trunks, the caller will only hear the virtual ring back tone
generated by the system before callee answers the call.
·
Distinctive Caller ID
When incoming calls arerouted from ring group/queue/IVR, the caller ID
displays with the name of ring group/queue/IVR, for example
5503302(ringgroup_default).
Note: To display IVR's name, please press the key instead of the extension
number directly.
·
Attended Transfer CallerID
When transferring an incoming call using the attended transfer feature code or
the transfer key of IP phone, the Caller ID of transferee or transferer displayed
on the screen of the callee. The default display is the Caller ID of the initiator.
For example, if extension 500 makes a call to extension 501. After 501 picks up
the call, 501 makes an attended transfer to extension 502. If
selecting “Transferer”, 502 will display the Caller ID as 500; if
selecting “Transferee”, 502 will display the Caller ID as 501.
·
Follow Me Prompt
When set “Follow me” to “Transfer to number” on the extension page (e.g. when
500 is busy, transfer to 501), while 500 is busy, the call will be transferred to
501. If “Enable Follow Me Prompt” choosing yes, there will be prompt before
transferring the call. Otherwise, the call will be transferred directly without any
prompt. Default: Yes.
·
Music on Hold for Follow Me Prompt
Configure whether to play a prompt “please hold while I try to locate the person
you are calling” when transfer a call by follow me settings.
www.yeastar.comPage102
MyPBX U5XX Administrator's Guide
·
Invalid Phone Number Prompt
Configure the prompt when the dialed phone number is invalid.
·
Busy Line Prompt
Configure the prompt when the dialed phone number is busy.
·
Dial Failure Prompt
Configure the prompt when dial failed due to conjunction no-available channel.
2) Extension Preferences
·
User Extensions
The default value is 500 to 616
·
Ring Group Extensions
The default value is 620 to 629
·
Paging Group Extensions
The default value is 630 to 639
·
Conference Extensions
The default value is 640 to 659
·
IVR Extensions
The default value is 660 to 679
·
Queue Extensions
The default value is 680 to 689
6.6.2 Business Hours
Business hours including “holiday configuration” is used to control the incoming
calls, we can configure it in this page.
www.yeastar.comPage103
MyPBX U5XX Administrator's Guide
Figure 6-54 Business Hours Settings
1) General
·
Enable Business Hours
·
disable Business Hours
2) Others
·
Enable Office Closed Timing
By dialing *81 (*81 is default) on an extension will force the office time closed
for the device whatever the general setting is.
·
Enable Office Timing
By dialing *82 (*82 is default) on an extension will force the office time to take
effect for the device whatever the general setting is.
·
Disable Office closed timing
By dialing *081 (*081 is default) on an extension will disable the Office Closed
Timing.
3) Add office hours
You can setup the business hours here.
4) Add Holiday
You can setup the holidays here.
If a time period is configured as both Holidays and office hours, it will be treated
as Holidays.
www.yeastar.comPage104
MyPBX U5XX Administrator's Guide
6.6.3 Feature Codes
There are many feature codes available in MyPBX, which allow users to dial from
extension side to realize the exact feature.
Figure 6-55 Feature Code Settings Page
1) General
·
One Touch Record
A user may initiate or stop call recording by dialing *1during a call. (*1 is default
setting).
·
Extension for Checking Voicemail
Users can check their Voicemail by dialing *2 on their phone (*2 is default
setting).
·
Voicemail for Extension
Users can leave a voicemail to other extensions by dialing # on their phone or
the incoming call could be forwarded to an extension‟s voicemail directly. (# is
default setting).
For example, extension 500 want to leave a message for extension 501, users
can use 500 dial“#501” to enter the voicemail of 501.
·
Voicemail main menu
Users can go to the main menu by dialing *02 (*02 is default setting).
·
Attended Transfer
Users may transfer an incoming call by dialing *3 on their phone (*3 is default
www.yeastar.comPage105
MyPBX U5XX Administrator's Guide
setting).
·
Attended Transfer Timeout
The time out of transferring a call
·
Blind Transfer
Users may blind transfer an incoming call by dialing*03 on their phone (*03 is
default setting).
·
Call Pickup
Users may pick up an incoming call by dialing *4 on their phone (*4 is default
setting)
·
Extension Pickup
Users may pick up a specific extension‟s incoming call by dialing *04+extension
number on their phone (*04 is default setting)
·
Intercom
Define the feature code that is used to dial an extension in intercom mode. For
instance, setting this value to *5 would allow you to initiate an intercom call with
extension 501 by dialing *5501.
·
Normal Spy
In this mode, you can only listen to the extension being spied, for example you
can dial *90501 to monitor extension 501
·
Whisper Spy
In this mode you can listen/whisper to the extension being spied, for example,
dialing *91501 to listen to extension 501, you can also talk with 501 too.
·
Barge Spy
In this mode, you can barge in both extensions involved in the call, for example
dialing *92501 to barge in and talk with extensions on both sides.
2) Call Park Preferences
·
Call Parking
User may park an incoming call on his own telephone by pressing “*6” (*6 is
default setting)
·
Extension range used to park calls
User may park an incoming call on a designated extension at first and then pick
up the call again on any other extension.
·
Number of seconds a call can be parked before it is recalled.
Define the time (in seconds) that a call can be parked before it is recalled to the
www.yeastar.comPage106
MyPBX U5XX Administrator's Guide
station that parked it.
3) Call Forwarding Preferences
·
Reset to Defaults
Users may reset all call forwarding defaults by calling *70 on their phone (*70
is default setting).
Note: When reset to defaults. The call forwarding settings will be configured as
follows:
Always forward: Disabled
Busy forward to Voicemail: Enabled
No answer forward to Voicemail: Enabled
Do not disturb: Disabled
·
Enable Forward All Calls
Users may enable always forward by calling *71 on their phone (*71 is default
setting)
·
Disable Forward All Calls
Users may disable always forward by calling *071 on their phone (*071 is
default setting)
·
Enable Forward When Busy
Users may enable busy forward by dialing *72 on their phone (*72 is default
setting)
·
Disable Forward When Busy
Users may disable busy forward by calling *072 on their phone (*072 is default
setting)
·
Enable Forward No Answer
Users may enable no answer forward by calling *73 on their phone (*73 is
default setting)
·
Disable Forward No Answer
Users may disable no answer forward by calling *073 on their phone (*072 is
default setting)
·
Forward to number
Users may activate call forwarding by dialing this feature code, followed by the
extension or phone number to forward all calls to this number.
Note: Users may activate Forward to number by dialing *74 + phone number.
e.g.: by dialing *74501, all calls will be forwarded to extension 501.
www.yeastar.comPage107
MyPBX U5XX Administrator's Guide
·
Forward to Voicemail
Users may forward the call to Voicemail by calling *074 on their phone (*074 is
default setting)
·
Enable Do Not Disturb
Users may enable do not disturb by calling *75 on their phone (*75 is default
setting)
·
Disable Do Not Disturb
Users may disable do not disturb by calling *075 on their phone (*075 is default
setting)
6.6.4 Voicemail Settings
In this page, we can configure some settings for voicemail feature, including
general voicemail settings and SMTP settings, which is used for “voicemail to
email”
Figure 6-56 General Voicemail Settings
1) General Voicemail Settings
a) Message Options
·
Max Messages per Folder
Set the maximum number of messages that can be stored in a single voicemail
box.
·
Max Message Time
Set the maximum length of a single voicemail message.
www.yeastar.comPage108
MyPBX U5XX Administrator's Guide
·
Min Message Time
Set the minimum length of a single voicemail message. Messages below this
threshold will be automatically deleted.
·
Ask Caller to Dial 5
If this option is set, the caller will be prompted to press 5 before leaving a
message.
·
Operator Breakout from Voicemail
If this option is set, the caller can jump out of the voicemail and go to the
destination (IVR) you set by dialing “0”.
b) Greeting Settings
·
Busy Prompt
Greeting played when the extension called is busy.
Skip greeting: Do not play a greeting.
Play busy greeting: play the extension busy greeting.
·
Unavailable Prompt
Greeting played when the extension called is Unavailable.
Skip greeting: Do not play a greeting.
Play Unavailable greeting: play the extension Unavailable greeting.
·
Leave a Message Prompt
Greeting played to ask the caller to dial 5 to leave a message.
Skip greeting: Do not play a greeting.
Play busy greeting: play the extension busy greeting.
Play Unavailable greeting: play the extension Unavailable greeting.
c) Playback Options
·
Announce Message Caller ID
If this option is enabled, the Caller ID of the party that left the message will be
played back before the voicemail message begins playing.
·
Announce Message Duration
If this option is set, the duration of the message in minutes will be played back
before the voicemail message begins playing.
.Announce Message Arrival Time
If this option is set, the arrival time of the message will be played back before
the voicemail message begins playing.
.Allow Users to Review Messages
www.yeastar.comPage109
MyPBX U5XX Administrator's Guide
Allow callers to review their recorded message before sending it to voicemail.
2) SMTP Settings for Voicemail
Note: If you want to send voicemail messages as email attachments, please
configure this section.
Figure 6-57 SMTP Server Settings
·
E-mail Address
The E-mail Address that MyPBX will use to send voicemail.
·
Password
The password for the email address used above
·
SMTP Server
The IP address or hostname of an SMTP server that the MyPBXwill connect to in
order to send voicemail messages via email, i.e. mail.yourcompany.com.
·
Port
SMTP Port: the default value is 25.
·
Use SSL/TLS to send secure message to server
If the server of sending email needs to authenticate the sender, you need to
select the check box.
Note: Must be selected for Gmail or exchange server.
After filling out the above information, you can click on the “Test Account
Settings” button to check whether the setup is OK.
1) If the test is successful, you can use the email safely.
2) If test failed, please check if the above information is correct or network is
proper.
www.yeastar.comPage110
MyPBX U5XX Administrator's Guide
6.7 Advanced Settings
6.7.1 SIP Settings
Figure 6-58 SIP Settings-General
1) General
·
UDP Port
Port use for sip registrations, Default is 5060.
·
TCP Port
Port use for sip registrations, Default is 5060.
·
TLS Port
Port use for sip registrations, Default is 5061.
·
TLS Verify Server
When using MyPBX as a TLS client, whether or not to verify server‟s certificate.
It is “No” by default.
·
TLS Verify Client
When using MyPBX as a TLS server, whether or not to verify client‟s certificate.
It is “No” by default.
·
TLS Ignore Common Name
Set this parameter as “No”, then common name must be the same with IP or
domain name.
·
TLS Client Method
www.yeastar.comPage111
MyPBX U5XX Administrator's Guide
When using MyPBX as TLS client, specify the protocol for outbound TLS
connections. You can select it as tlsv1, sslv2 or sslv3.
·
RTP Port Start
Beginning of RTP port range
·
RTP Port End
End of RTP port range
·
DTMF Mode
Set default mode for sending DTMF.Default setting: rfc2833
·
Max Registration/Subscription Time
Maximum duration (in seconds) of a SIP registration. Default is 3600 seconds.
·
Min Registration/Subscription Time
Minimum duration (in seconds) of a SIP registration. Default is 60 seconds.
·
Default Incoming/Outgoing Registration Time
Default Incoming/Outgoing Registration Time: Default duration (in seconds) of
incoming/outgoing registration.
·
Register Attempts
The number of SIP REGISTER messages to send to a SIP Registrar before giving
up. Default is 0 (no limit).
·
Register Timeout
Number of seconds to wait for a response from a SIP Registrar before timed out.
Default is 20 seconds.
·
Calling Channel Codec Priority
Once enabled, when dialing out via SIP/SPS trunks, the codec of calling channel
will be selected in preference. If not, MyPBX will follow the priority in your
SIP/SPS trunks.
·
Video Support
Support for SIP video or no. Default is yes.
·
Max Bit Rate
Configure the max bit rate for video stream. The default: 384kb/s
·
DNS SRV Look Up
Please enable this option when your SIP trunk contains more than one IP
address.
www.yeastar.comPage112
MyPBX U5XX Administrator's Guide
·
User Agent
To change the user agent parameter of asterisk, the default is “MyPBX”, you
could change it if needed.
Figure 6-59 SIP Settings-NAT
2) NAT
Note: Configuration of this section is only required when using remote
extensions.
·
Enable STUN
STUN (Simple Traversal of UDP through NATs) is a protocol for assisting devices
behind a NAT firewall or router with their packet routing.
·
STUN Address
The STUN server allows clients to find out their public address, the type of NAT
they are behind and the internet side port associated by the NAT with a
particular local port. This information is used to set up UDP communication
between the client and the VOIP provider and so establish a call.
·
External IP Address
The IP address that will be associated with outbound SIP messages if the system
is in a NAT environment.
·
External Host
Alternatively you can specify an external host, and the system will perform DNS
queries periodically.
This setting is only required when your public IP address is not static. It is
recommended that a static public IP address be used with this system. Please
contact your ISP for more information.
·
External Refresh Interval
www.yeastar.comPage113
MyPBX U5XX Administrator's Guide
If an external host has been supplied, you may specify how often the system will
perform a DNS query on this host. This value is specified in seconds.
·
Local Network Identification
Used to identify the local network using a network number/subnet mask pair
when the system is behind a NAT or firewall.
Some examples of this are as follows:
“192.168.0.0/255.255.0.0”: All RFC 1918 addresses are local networks;
“10.0.0.0/255.0.0.0”: Also RFC1918;
“172.16.0.0/12”:Another RFC1918 with CIDR notation;
“169.254.0.0/255.255.0.0”: Zero conf local network.
Please refer to RFC1918 for more information.
·
NAT Mode
Global NAT configuration for the system; the options for this setting are as
follows:
Yes = Use NAT. Ignore address information in the SIP/SDP headers and reply to
the sender's IP address/port.
No = Use NAT mode only according to RFC3581.
Never = Never attempt NAT mode or RFC3581 support.
Route = Use NAT but do not include rport in headers.
·
Allow RTP Reinvite
By default, the system will route media steams from SIP endpoints through
itself. Enabling this option causes the system to attempt to negotiate the
endpoints to route packets to each other directly, bypassing the system. It is not
always possible for the system to negotiate endpoint-to-endpoint media
routing.
Figure 6-60 SIP Settings-Codecs
3) Codecs
A codec is a compression or decompression algorithm that used in the
www.yeastar.comPage114
MyPBX U5XX Administrator's Guide
transmission of voice packets over a network or the Internet.
u-law: A PSTN standard codec, used in North America, which provides very
good voice quality and consumes 64kbit/s in each direction (receiving and
transmitting) of a VoIP call.
a-law: A PSTN standard codec, used outside of North America, which provides
very good voice quality and consumes 64kbit/s in each direction (receiving and
transmitting) of a VoIP call.
GSM/UMTS: A wireless standard codec, used worldwide, that provides
adequate voice quality and consumes 13.3kbit/s in each direction (receiving
and transmitting) of a VoIP call. GSM/UMTS is supported by many VoIP phones.
SPEEX:Speex is an Open Source/Free Software patent-free audio compression
format designed for speech. The Speex Project aims to lower the barrier of entry
for voice applications by providing a free alternative to expensive proprietary
speech codecs. Moreover, Speex is well-adapted to Internet applications and
provides useful features that are not present in most other codecs.
G.722:G.722 is a wideband speech coding algorithms which supports the bit
rate of 64, 56 and 48kbps wideband. It‟s a broadband voice encoding of G
series.
G.726: A PSTN codec, used worldwide, that provides good voice quality and
consumes 32kbit/s in each direction (receiving and transmitting) of a VoIP call.
G.726 is supported by some VoIP phones.
ADPCM, G.729A, H261, H263, H263p, H264, MPEG4.
Note: If you would like to use G.729, please enter your license.
Figure 6-61 SIP Settings-QoS
4) QoS
QoS (Quality of Service) is a major issue in VoIP implementations. The issue
is how to guarantee that packet traffic for a voice or other media connection
will not be delayed or dropped due interference from other lower priority
traffic. When the network capacity is insufficient, QoS could provide priority
www.yeastar.comPage115
MyPBX U5XX Administrator's Guide
to users by setting the value.
Figure 6-62 SIP Settings-Advanced Settings
5) Advanced Settings
·
From Field
Where to get the caller ID in sip packet.
·
To Field
Where to get the DID in sip packet.
·
180 Ringing
It is set when the telecom provider needs. Usually it is not needed.
·
Remote Party ID
Whether send Remote-Party-ID on SIP header. Default no.
·
Allow Guest
Whether allow anonymous registration extension. Default: no.
This option is used to avoid some anonymous calls by hackers. For more details
about the system security configuration, please refer to APPENDIX BMyPBX
Security Configuration Guide.
·
Pedantic
Enable pedantic parameter. Default: no.
·
Alwaysauthreject
If enabled, when MyPBX rejects “Register” or “Invite” packets, MyPBX always
respond the packets using “SIP404 NOT FOUND”.
·
Session -timers
Enable session-timer mode, default: yes
·
Session-expires
www.yeastar.comPage116
MyPBX U5XX Administrator's Guide
The max refresh interval
·
Session-minse
The min refresh interval, which mustn't be less than 90s
·
Session-refresher
Choose session-refresher, the default is Uas
6.7.2 IAX Settings
Figure 6-63 IAX Settings
1) General
·
Bind Port
Port use for IAX2 registrations, Default is 4569.
·
Bandwidth
Low/medium/high with this option you can control which codec to be used.
·
Min Registration Time
Minimum duration (in seconds) of a IAX2 registration. Default is 60 seconds.
·
Max Registration Time
Maximum duration (in seconds) of a IAX2 registration. Default is 1200 seconds.
2) Codecs
A codec is a compression or decompression algorithm that used in the
transmission of voice packets over a network or the Internet.
u-law: A PSTN standard codec, used in North America, that provides very good
voice quality and consumes 64kbit/s in each direction (receiving and
transmitting) of a VoIP call.
a-law: A PSTN standard codec, used outside of North America, that provides
www.yeastar.comPage117
MyPBX U5XX Administrator's Guide
very good voice quality and consumes 64kbit/s in each direction (receiving and
transmitting) of a VoIP call.
GSM: A wireless standard codec, used worldwide, that provides adequate voice
quality and consumes 13.3kbit/s in each direction (receiving and transmitting)
of a VoIP call. GSM/UMTS is supported by many VoIP phones.
SPEEX:Speex is an Open Source/Free Software patent-free audio compression
format designed for speech. The Speex Project aims to lower the barrier of entry
for voice applications by providing a free alternative to expensive proprietary
speech codecs. Moreover, Speex is well-adapted to Internet applications and
provides useful features that are not present in most other codecs.
G.726: A PSTN codec, used worldwide, that provides good voice quality and
consumes 32kbit/s in each direction (receiving and transmitting) of a VoIP call.
G.726 is supported by some VoIP phones.
ADPCM, G.729A, H261, H263, H263p, H264.
Note: If you would like to use G.729, please enter your license.
6.7.3 Blacklist
Blacklist is used to block an incoming/outgoing call. If the number of
incoming/outgoing call is registered in the number blacklist, the caller will hear
the following prompt: “The number you have dialed is not in service. Please
check the number and try again”.The system will then disconnect the call.
Figure 6-64 Blacklist List
We can add a number with the type: inbound, outbound or both
Figure 6-65 Add a Number as Blacklist
Note: Add an extension in blacklist, such as 300:
www.yeastar.comPage118
MyPBX U5XX Administrator's Guide
1) If the type is “inbound”, then this extension can‟t dial other extension and
external numbers, but it can dial IVR or ringgroup.
2) If the type is “outbound”, then this extension can‟t be called.
6.7.4 Callback Settings
MyPBX allows caller A to dial an inbound route number, and after hearing the
ring, A can hang up the call or wait for MyPBX to cut off the call, then MyPBX will
call A with this number. When A picks up the call, A can dial the number he
wants to call; MyPBX will call the number with its outbound route.
Notes:
1. If you‟d like to use callback feature, please make sure it‟s enabled on the
inbound route setting panel.
2. No callback rules needed to be set if the trunk supports call back with the
caller ID directly.
Figure 6-66 Callback Settings Page
·
Allow All Numbers
If you want to apply Callback function to all incoming numbers, please tick Allow
All numbers.
Follow the step to use this function.
Step 1: Enable Callback.
Inbound Routes – Choose “Yes” on” Enable Callback” to enable this function.
www.yeastar.comPage119
MyPBX U5XX Administrator's Guide
Figure 6-67 Enable Callback in Inbound Route
Step 2: Create Callback number
Figure 6-68 Add a New Callback Number
Step 3: Create Callback Rules
You will need to create callback rules when the system should strip or add digits.
Figure 6-69 Create Callback Rule
·
Trunk Name
Choose the trunk with callback rules
·
Strip digits from front
Define how many digits will be stripped from the call in number before the
callback is placed. For example, when you call from number 123456789 into
MyPBX, the caller ID is 0123456789, but you can only call 123456789
successfully from MyPBX trunk. You should configure number 0123456789 as
the call back number and strip 1 digit before the callback is placed
·
Prepend before dialing
Define digits added before a callback number before the callback is placed. For
www.yeastar.comPage120
MyPBX U5XX Administrator's Guide
example, the call in number (Caller ID) is 123456789, MyPBX need to send
9123456789 to its trunk when call to this number. You should configure
123456789 as the call back number and add 9 before the callback is placed. You
can add “w” for analog trunks for some delay too.
6.7.5 DNIS Settings
DNIS (Dialed Number Identification Service) is a telephone service that
identifies for the receiver of a call the number that the caller dialed
Figure 6-70 Add a New DNIS
Note: If DID is not configured here, all the calls via this trunk will show the DNIS
instead of the original caller ID
6.7.6 DISA
DISA (Direct Inward System Access) allows someone calling in from outside the
telephone switch (PBX) to obtain an “internal” system dial tone and make calls
as if they were using one of the extensions attached to the telephone switch. To
use DISA, a user calls a DISA number, which invokes the DISA application. The
DISA application in turn requires the user to enter a PIN number, followed by the
pound sign (#). If the PIN number is correct, the user will hear dial tone on
which a call may be placed. Obviously, this type of access has serious security
implications, and great care must be taken not to compromise your security.
www.yeastar.comPage121
MyPBX U5XX Administrator's Guide
Figure 6-71 Add a New DISA
1) General
·
DISA Name
Give this DISA application a name to help you identify it.
·
PIN #
The password for this DISA
·
Response Timeout
The maximum amount of time the system will wait before hanging up the call if
the user has dialed an incomplete or invalid number. Default is 10 seconds.
·
Digit Timeout
The maximum amount of time permitted between each digit when the user is
dialing an extension number. Default is 5 seconds.
2) Member Outbound Routes
Used to set the outbound routes that can be accessed from this DISA
6.7.5 PIN User Settings
PIN User is used to manage lists of PINs that can be used to access restricted
features such as Outbound Routes.
www.yeastar.comPage122
MyPBX U5XX Administrator's Guide
Figure 6-72 PIN User Settings Page
1) Options
·
Access Code
.Dial this code to access PIN.
·
Prompt for Entry
Prompt caller enter the PIN Number.
·
Prompt for Entry Failure
Prompt the caller when an invalid PIN is entered.
Figure 6-73 Add a New PIN User
2) PIN User
MyPBX can store a number of PIN Users. PIN Users may be used to keep track
www.yeastar.comPage123
MyPBX U5XX Administrator's Guide
of calls in relation to particular activities or clients. They can also be used to
keep track of calls by particular users or sets of users.
• PIN entered are checked against those stored by the system. If an invalid PIN
is entered, the PIN is requested again.
• The system administrator can configure certain numbers or types of numbers
to require entry of a PIN before you can continue making a call to such a
number.
• The system administrator can also configure you to have to enter a PIN before
making any external call.
·
Name
A character-based name for this PIN list, i.e. “YeastarPIN”
·
PIN List
Enter a list of one or more PINs, One PIN per line.
·
Outbound Route
PIN User can use those outbound route to make call out.
6.7.8 Paging Groups
Paging is used to make an announcement over the speakerphone to a phone or
group of phones. Targeted phones will not ring, but instead answer immediately
into speakerphone mode. Please note that this section is for configuring paging
groups. If you would like to configure Intercom settings, please open the Other
Settings -> Feature Codes screen.
This feature is supported by the following SIP phones:
Yealink's T28, T26, T22, T20, T10T, T9CM. Other SIP devices may also work
with this feature but are not officially supported.
Note:A paging group can have a maximum of 20 members.
Figure 6-74 Paging Group List
In this mode, if you dial its number, MyPBX will help to pick up those chosen
members and you can talk directly without any rings.
www.yeastar.comPage124
MyPBX U5XX Administrator's Guide
Figure 6-75 Add/Edit Internal Paging Group
·
Paging Group Number
Define the numbered extension that may be dialed to reach this group.
·
Duplex
Paging is typically one way for announcements only. Checking this will make
paging duplex, allowing all users in the group to talk and be heard by all.
6.7.9 SMS Settings
When GSM/UMTS modules are installed, SMS feature is supported.
1) Enable SMS to Email
Figure 6-76 Enable SMS to Email
If you enable this, as soon as the GSM/UMTS trunks receive small messages,
MyPBX will send the text of this message to the email addresses listed on the
Email List.
You can add email addresses to the Email List
www.yeastar.comPage125
MyPBX U5XX Administrator's Guide
Figure 6-77 SMS to Email Settings
2) Enable Email to SMS
If you enable this, you can use MyPBX to send out message by sending an email
to the specified address.
Figure 6-78 Email to SMS Settings
·
Enable Country Code
If you want to add country code before the dialed numbers, please tick this.
·
Country Code
The country code will be added before the numbers which you want to send
SMS.
·
Receive mails every
The interval time of receiving mails from POP3 server
·
Access Code
This PIN code is used to verify the subject of the emails received. If the form of
email passes the verification, it will be send out by SIM card. If not, this email
will be deleted immediately.
3) Email Settings
www.yeastar.comPage126
MyPBX U5XX Administrator's Guide
Figure 6-79 SMTP/POP Server Settings
Note:
1. If you want to use “SMS to Email”, please configure POP3 setting.
2. If you configure the POP3 setting, MyPBX will download emails from the mail
server regularly. Once downloaded, the emails will be deleted from the mail
server.
·
Email Address
This email address will be used to:
1. Send email to the addresses listed on “SMS to Email” setting.
2. Receive email and send the text of the email to the target mobile number by
SMS.
Note: If you use Gmail, just put your user name here. E.g. email address:
test@gmail.com, you just put “test” here.
·
Password
Input the password of this email here.
·
SMTP Server (SMTP)
·
SMTP Server Port
·
Receive Server (POP3)
·
Receive Server Port
If you want to know more about Email to SMS, please refer toAPPENDIX G
6.7.10 Certificates
MyPBX can support TLS extension. Before you register TLS extension on IP
phone, you should upload certificates first.
www.yeastar.comPage127
MyPBX U5XX Administrator's Guide
Figure 6-80 Upload Certificate
Trusted Certificate
This certificate is a CA certificate. When selecting “TLS Verify Client” as “Yes”,
you should upload a CA. The relevant IP phone should also have the according
server certificate.
PBX Certificate
This certificate is server certificate. No matter selecting “TLS Verify Client”
as “Yes” or “NO”, you should upload this certificate to MyPBX. If IP phone
enables “TLS Verify server”, you should also upload the according CA certificate
on IP phone.
、
www.yeastar.comPage128
MyPBX U5XX Administrator's Guide
7 Reports
Click
to access
We can check the call detailed logs for counting and system log for debugging
7.1 Call Logs
The call Log captures all call details, including call time, caller number, callee
number, call type, call duration,etc. An administrator can search and filter call
data by filter the call logs by call date, caller/callee, trunk, duration, billing
duration, status, communication type and Pin User.
Figure 7-1 Call Log List
www.yeastar.comPage129
MyPBX U5XX Administrator's Guide
7.2 System Logs
Figure 7-2 System Logs
You can download and delete the system logs of MyPBX.
Options
·
Enable Hardware Log
Save the information of hardware; (up to 4 log files)
·
Enable Normal Log
Save the prompt information; (up to 16 log files)
·
Enable Web Log
Save the history of web operations (up to 2 log files)
·
Enable Debug Log
Save debug information (up to 2 log files)
Packets Capture Tool
This feature always used to capture packets for technician. Integrate packet
capture tool “Wireshark” in MyPBX.
Users also could specify the destination IP address and port to get the packets.
·
IP
Specify the destination IP address to get the packets.
·
Port
Specify the destination Port to get the packets.
·
NIC
Choose the NIC (LAN or WAN) which you want to capture the packets.
www.yeastar.comPage130
MyPBX U5XX Administrator's Guide
8 Addons
Click
to enter “Addons” page.
MyPBX supports many addons to enhance the function of MyPBX.
In this page, you can install the according addons, including MyPBX Client, Bill
System and Hotel Module.
Before you install an addon, you should have a license. You can buy the license
from Yeastar.
Figure 8-1 Addon Page
8.1 MyPBX Client
MyPBX Client is an application coordinated with MyPBX that connects your PC
and IP phones. With MyPBX Client, you can perform various operations including
check extension status, manage contacts, voicemails, and CDR of extension,
realize click-to-call and call popup, send instant messages between extensions,
initiate a conference call, and create a call task, etc.
For more details about MyPBX client, please refer to the link below:
http://www.yeastar.com/Solutions/MyPBX_Client_Solution.asp
8.2 Billing System
Billing System caters for the growing need of billing solutions that can efficiently
monitor the calls and maintain record of each call received/transferred by
IP-PBX. Billing System can charge and recharge extensions and conduct
analysis on the basis of statistics. Both prepaid and postpaid are supported.
Flexible rate settings and detailed records make it extremely easy for enterprise
to monitor charges, spot misuse, and enhance efficiency. With Billing System,
www.yeastar.comPage131
MyPBX U5XX Administrator's Guide
call accounting are just clicks away.
Note: If Billing System is enabled, DISA and Callback functions would be
disabled.
For more details about Bill System, please refer to the link below:
http://www.yeastar.com/Solutions/Billing_System_Solution.asp
8.3 Hotel Module
MyPBX Hotel Module is designed for inns and hotels. The features include Room
Status, Booking, Check In, Check Out, Wakeup Call, Do Not Disturb, Mini Bar,
and Billing Report.
For more details about “Hotel Module”, please refer to the link below:
http://www.yeastar.com/Solutions/Hotel_Module_Solution.asp
www.yeastar.comPage132
MyPBX U5XX Administrator's Guide
9 Logout
Click
to log out safely.
www.yeastar.comPage133
MyPBX U5XX Administrator's Guide
10. Use MyPBX
Figure 10-1 U5XX Connection Drawing
10.1 Make outbound call
To make an outbound call, we need to add trunk first. There are 3 types of VoIP
Trunk.
·
DigitalTrunk: E1/T/J1 ports of MyPBX, connected to the ISDN provider
you need to get the detailed signaling type from the provider before configure
the E1 trunk.
·
VoIP Trunk: Connected to remote VOIP service server.
you should get an IP address with user name/ password from the provider.
·
Service Provider: Connected to service provider server.
you will get only IP address for authorization.
·
Analog Trunk: FXO ports of MyPBX, connected to a local PSTN.
·
GSM/UMTS Trunk: GSM ports of MyPBX, connected to GSM Network.
·
BRI Trunk: BRI ports of MyPBX, connected to ISDN provider
What are FXO and FXS?
FXS (Foreign Exchange Station) is an interface which drives an analog
www.yeastar.comPage134
MyPBX U5XX Administrator's Guide
telephone or FAX machine. FXS interfaces deliver power, provide ringing, and
use FXO signaling. FXS interfaces are what allow you to hook telephones and
other analog devices to your PBX
FXO (Foreign Exchange Office) is an interface that connects to a phone line to
supply your PBX with access to a public telephone network. FXO interfaces use
FXS signaling. FXO interfaces allow you to connect your PBX to real analog
phone lines.
10.1.1 Sample Routing via E1 Trunk
Let‟s route all inside extensions through an E1 trunk by dialing 9. In
Outbound Routes, add a new outbound route as below.
Figure10-2 Create Outbound Route for E1 Trunk
www.yeastar.comPage135
MyPBX U5XX Administrator's Guide
As we can see from the outbound route of „pstnout‟, all phone numbers
starting with 9 will have their first digit stripped off (digit 9) and will be
sentto the E1.
After we have configured the above, we can dial 9 + local number to dial out
via a E1 trunk.
Note: Setting number prefix to wild card X. and setting Strip to 0 digits from
the front will allow all calls to go through this outbound route directly.
10.1.2 Sample Routing via VoIP Trunk
Let‟s configure all inside extensions to dial „0‟ through the VoIP Trunk.
1. Add VoIP service provider
Before we do add this, please make sure you have a VoIP Trunk account.
TrunksVoIP Trunk SIP Trunk
Enter your account information on this page, and click Save.
www.yeastar.comPage136
MyPBX U5XX Administrator's Guide
Figure10-3 Create an VOIP Trunk
2. Add Outbound Routes
As we can see from the Outbound Route of „VOIP_OUT‟, all phone numbers
starting with 0will have their first digit stripped off (digit 0) and will be sent
to the SIP Trunk.
www.yeastar.comPage137
MyPBX U5XX Administrator's Guide
Figure10-4 Create an Outbound route for VOIP trunk
Now that we have added two outbound dialing rules, any call starting with 9
will be routed to the PSTN, and any number starting with 0 will be routed to
the SIP Trunk.
10.2 Incoming call
www.yeastar.comPage138
MyPBX U5XX Administrator's Guide
10.2.1 Sample Routing to an IVR
Let‟s configure an incoming call to route to the IVR. In the IVR itself, let‟s
configure digit 0to route the call to extension 300, and digit 1 to route the
call to extension 301.
1. Add IVR
To add a new IVR, go to IVR Create New IVR
Figure10-5 Create IVR
2. Add Inbound Routes
As we can see from the Inbound Route of„VOIP_IN‟, all incoming calls will be
www.yeastar.comPage139
MyPBX U5XX Administrator's Guide
sent to the IVR.
Figure10-6 Create Inbound Route for VOIP Trunk
APPENDIX A FAQ
www.yeastar.comPage140
MyPBX U5XX Administrator's Guide
Q1. How to Register SIP devices?
A1:
1)Register SIP softphone
Download the x-lite softphone from counterpath website
www.counterpath.com
After install the x-lite, right click the panel and select the SIP Account setting
and then configure it.
Display Name: 500
User Name: 500
Password: 500
Authorization Name: 500
Domain: 192.168.5.150
2) Register IP Phone (for example, Yealink‟s T28 IP Phone)
a) Connect the T28‟s Internet port to the switch. And it can get the IP from
your route.
b) Press the „OK‟ key on T28 to get the IP of T28.
c) Put the IP on web browser then you can enter the T28 configure page
through this IP.
d) Put the SIP extensions info on the T28 IP phones.
Display Name: 501
User Name: 501
Register Name: 501
Password: 501
SIP Server: 192.168.5.150
Use the same method register another T28 to other extension.
Q2. How do I reset MyPBX back to the factory default settings?
A2: To perform a reset, please follow steps below:
Step 1:Hold downthe „Reset‟ button on the back of the unit for 5 seconds
and watch the LEDs on the front of the MyPBX. When the status LED turns
red, let go of the reset button.
Step2:When the RUN status LED starts blinking,MyPBX will be set back to
factory defaults.
Step 3: To access the configuration page, navigate to192.168.5.150using a
web browser. Make sure that you are on the 192.168.5.0 subnet before
doing this.
Step4: Login to the device with the username „admin‟ and the password
„password‟, in order to begin reconfiguring the device.
APPENDIX
B
MyPBX
Security
www.yeastar.comPage141
MyPBX U5XX Administrator's Guide
Configuration Guide
VoIP attacks, although it is not an everyday occurrence, it does exist. While
using VoIP, system security is undoubtedly one of the issues we care about most.
But with the appropriate configuration, and some basic safety habits, we can
improve the security of the telephone system. Moreover, the powerful built-in
firewall function in MyPBX is adequate to enable the system to run safely and
stably.
This guide will introduce the highest defense level in MyPBX,and we strongly
recommend that you configure firewall and other security options according to
this guide, to prevent the attack fraud and the system failure or calls loss.
1. Security Configuration for Web GUI
1.1 Change the default access port for HTTP on
Options page
PBXBasic Settings General PreferencesHTTP Bind Port
www.yeastar.comPage142
MyPBX U5XX Administrator's Guide
Figure B-1
1.2 Change the default password for the web GUI
SystemSystem PreferencesChange Password
Figure B-2
2. Disable SSH on LAN Settings Page
2.1 Disable SSH
Select LAN SettingsEnable SSH. If external debugging isn‟t required, please
select “No”.
Figure B-3
www.yeastar.comPage143
MyPBX U5XX Administrator's Guide
2.2 Change the default password for SSH
We can use the Linux command passwd to change root password of MyPBX.
1. Login via putty.exe
Figure B-4
2. The default username is root and the default password is ys123456.
Figure B-5
3. Use command passwd to change the root‟s password
www.yeastar.comPage144
MyPBX U5XX Administrator's Guide
Figure B-6
3. Security Configuration for Extensions
3.1 Change the default SIP Port
PBXBasic settingsSIP SettingsGeneralUDP Port
www.yeastar.comPage145
MyPBX U5XX Administrator's Guide
Figure B-7
3.2 Disable guest calls
PBXBasic settingsSIP SettingsAdvanced SettingsAllow Guest
Figure B-8
www.yeastar.comPage146
MyPBX U5XX Administrator's Guide
3.3 Security Configuration for remote extensions
If remote registration isn‟t required, please disable it.
PBXExtensionsFXS/VoIP Extensions VoIP ExtensionsGeneralVoIP
Settings
Figure B-9
3.4Set a robust password and enable IP restriction
for extensions
1) Set a new extension password at a higher security level, e.g. AjK5Up1G.
PBXExtensionsFXS/VoIP Extensions VoIP ExtensionsGeneralPassword
Figure B-10
2) Enable IP restriction and enter the permitted “IP address/Subnet mask”, e.g.
192.168.5.136.
www.yeastar.comPage147
MyPBX U5XX Administrator's Guide
Figure B-11
4. Setup Proper Firewall Rules
Note: Please backup the configurations on backup and restore page before you
go ahead.In the case that you lock the device, you can reset to factory default
and restore the previous configurations.
Step1. Enable firewall on firewall page of MyPBX.
SystemFirewall Settings Firewall RulesGeneral Settings
www.yeastar.comPage148
MyPBX U5XX Administrator's Guide
Figure B-12
Step2.Add a common rule to accept local network access.
Create a common rule to allow the all the IP addresses of the local phones to
access MyPBX server. For example, if the IP addresses of the local network are
192.168.5.1-254, the configurations could be as below:
Name: LocalNetwork
Protocol: BOTH
Port: 1:65535
IP: 192.168.5.0/255.255.255.0
Action: Accept
Figure B-13
Step3.Create
common rules to accept remote extensions or remote
administrators, if you use a SIP trunk, please accept the provider‟s host as well.
Note: If there are no remote extensions, the rule is not required.
Set up the firewall rule to allow the public IP address of remote extensions to
access MyPBX server. e.g.110.111.132.6, the configurations could be as below:
www.yeastar.comPage149
MyPBX U5XX Administrator's Guide
Name: Remote Extension
Protocol: BOTH
Port: 1:65535
IP: 110.111.132.6/255.255.255.255
Action: Accept
Figure B-14
Step4. Configure auto blacklist rules
Auto blacklist rules: the Server would add the IP address to the blacklist
automatically if the number of the packets it sends exceeds the rule you
configured.
Add two auto blacklist rules for port: 5060.
Rule No.1:
Port: 5060
Protocol: UDP
IP Packets: 120
Time Interval: 60 seconds
Figure B-15
Rule No.2:
Port: 5060
www.yeastar.comPage150
MyPBX U5XX Administrator's Guide
Protocol: UDP
IP Packets: 40
Time Interval: 2 seconds
Figure B-16
Add an auto blacklist rule for Port:8022
Rule No.3
Port: 8022
Protocol: TCP
IP Packets: 5
Time Interval: 60 seconds
Figure B-17
Step 5. Add a Firewall Rule for VoIP trunk registration
Note: If there is no VoIP trunk, this rule is not required. And if the RTP IP
address of VoIP trunk and Registration IP address of the VoIP trunk are different,
we need to create a rule to accept the RTP IP address too.
Add a rule to accept the IP address of the VoIP trunk to access MyPBX server. For
example: If the IP address of the VoIP trunk is 110.5.14.6, Protocol is UDP and
Port is 5060, the configuration could be as below:
Name: VoIPTrunk
Protocol: UDP
Port: 5060: 5060
IP: 110.5.14.6/255.255.255.255
www.yeastar.comPage151
MyPBX U5XX Administrator's Guide
Action: Accept
Figure B-18
Step 6. Add a firewall rule to accept remote access of HTTP port. For example,
if the remote access IP is 110.5.14.6, and the port is 80, the configuration could
be as below.
Name: RemoteHTTP
Protocol: TCP
Port: 80:80
IP: 110.5.14.6/255.255.255.255
Action: Accept
Figure B-19
www.yeastar.comPage152
MyPBX U5XX Administrator's Guide
Step 7. Add a firewall rule to accept remote access of SSH port. For example:
if the remote access IP is 110.5.14.6 and the port is 8022.
Note: If the remote access of SSH port is not needed, this rule is not required.
Name: RemoteSSH
Protocol: TCP
Port: 8022:8022
IP: 110.5.14.6/255.255.255.255
Action: Accept
Figure B-20
Step 8.
Add other firewall rules by yourself. For example, if you are using
features related to email, you should add the firewall rules for the SMTP server
and POP3 server.
Step 9.
Enable Drop all (If this feature is enabled, all the packets and
connection that do not match the rules would be dropped.)
Note: Before enable this feature, please add a rule to accept the local network
access, or the server might not be accessed.
www.yeastar.comPage153
MyPBX U5XX Administrator's Guide
Figure B-21
Step 10. The Configuration of firewall settings is completed. See the figures
below.
Figure B-22
www.yeastar.comPage154
MyPBX U5XX Administrator's Guide
Figure B-23
Step 11.
Define the authorized data transmitting rate and drop all other
unauthorized hosts.
Note:If we setup IP blacklist rules here, those unauthorized hosts will still be
able to send SIP packets into MyPBX if the packets transmitting rate is under the
rate defined. But as soon as the transmitting beyond the define rate, the IP will
be added into blacklist automatically.
This is useful for remote extension who is using dynamic IP address.
Remove all the IP blacklist rules if you don‟t allowed any other unauthorized
hosts access MyPBX.See as below figure.
Note: If „drop all‟ is not enabled, please don‟t remove the IP blacklist rules in
case the system security hole.
www.yeastar.comPage155
MyPBX U5XX Administrator's Guide
Figure B-24
Figure B-25
5. Alert Settings
After enabling alert settings‟, if the device is attacked, the system will alert the
users via call or e-mail. The attack modes include IP attack and Web Login.
www.yeastar.comPage156
MyPBX U5XX Administrator's Guide
5.1 IPATTACK
When the system is attacked by some IP addresses, the firewall will add the IP
to auto IP Blacklist and notify the user if it match the protection rule.
Example: Configure to notify extension 500, outbound number 5503301 and
E-mail alert@yeastar.com.
configuration could be as below.
Phone Notification Settings:
Phone Notification: Yes
Number: 500;5503301
Attempts: 1
Interval: 60s
Prompt: default
Note: If there is an outbound number to notify, the number should fit the dial
pattern of the outbound route.
E-mail Notification Settings:
E-mail Notification: Yes
To: alert@yeastar.com
Subject: IPAttack
Figure B-26
5.2 WEBLOGIN
www.yeastar.comPage157
MyPBX U5XX Administrator's Guide
Enter the password incorrectly five times when logging inMyPBX Web interface
will be deemed as attack, the system will limit the IP login within 10 minutes and
notify the user.
Example: Configure to notify extension 500, outbound number 5503301 and
E-mail alert@yeastar.com.
configuration could be as below.
Phone Notification Settings:
Phone Notification: Yes
Number: 500;5503301
Attempts: 1
Interval: 60s
Prompt: default
Note: If there is an outbound number to notify, the number should fit the dial
pattern of the outbound route.
E-mail Notification Settings:
E-mail Notification: Yes
To: alert@yeastar.com
Subject: WebLogin
Figure B-27
www.yeastar.comPage158
MyPBX U5XX Administrator's Guide
APPENDIX C How to Configure
external storage
Before External storage can be properly configured, an SMB share folder
accessible from MyPBX must be set up on a Windows based machine. Once
that has been set up, please follow the steps below.
Step 1 Add a new folder, rename it, and set this new folder‟s share
Properties according to Figure C-1.
FigureC-1 Set up share Properties
Step 2Enter the new folder and create a new text file, then rename this file
to status.txt. This step is very important, DO NOT forget to create the
status.txt file.
Step 3ConfigureExternal storagesettings on MyPBX to Figure C-2.
www.yeastar.comPage159
MyPBX U5XX Administrator's Guide
FigureC-2 External storageSetting
Net-Disk Host/IP:Change this to the IP address of the computer where
backup files will be stored.
Net-DiskShare Name: Change this to the name of the shared folder where
backups will be stored.
Net-DiskShare Username: The user name used to log into the network
share. Leave this blank if it is not required
Net-DiskShare Password: The password used to log into the network
share.Leave this blank if it is not required
If configuringis correctly, open your Windows share folder to see if the
MyPBX backup files and folders has been created.If the contents of the
backup folder look similar to Figure B-3, then you have successfully
configured External storage on the MyPBX unit.
FigureC-3 External storagesetting succeed
www.yeastar.comPage160
MyPBX U5XX Administrator's Guide
APPENDIX D How to Configure
NAT setting
When MyPBX is behind a NAT(firewall),you need to configure NAT
setting on MyPBX if you want to use a remote extension.
Please follow section 1 or 2 below depending on your network configuration.
1. If MyPBXis connected to a local network, you must set up port forwarding
on your router. Specifically, you must map port 5060 (default SIP port) and
port 10001-10200(default RTP port range) as UDP ports.
Next,log in MyPBX WebGUI, go to „PBX‟->‟Advanced Settings‟ ->‟SIP
Settings‟ ->„NAT‟
External IP Address: your router‟s public IP address
External Host: your router‟s domain
ExternalRefresh Interval: 20 seconds
Local Network Identification:192.168.5.0/255.255.255.0 (change this
according to your network configuration)
NAT mode: Yes
Allow RTP Reinvite: Yes
FigureD-1
Assuming that your router‟s host address is yeastar.3322.org, your local
network is from 192.168.5.1-192.168.5.254, and the subnet Mask is
255.255.255.0, the MyPBX network settings should configured like Figure
C-2
www.yeastar.comPage161
MyPBX U5XX Administrator's Guide
FigureD-2 MyPBX Network setting
2. If MyPBX has a public IP, (i.e. is connected directly to your internet service
provider), the network settings should be configured according to Figure
C-3:
FigureD-3
Now, MyPBX has been configured as a public IP, so there is no need to
configure NAT again, just leave all settings in „NAT‟ blank.
www.yeastar.comPage162
MyPBX U5XX Administrator's Guide
APPENDIX E How to Use Auto
Provision
Step1. Disable DHCP Server on your local network.
E.g. Disable DHCP Server on Linksys Router.
FigureE-1
Step2. Enable DHCP Server on MyPBX.
Login MyPBX web interface, „System‟„Network
Server‟„Enable DHCP Server‟.
Preference‟
->„DHCP
www.yeastar.comPage163
MyPBX U5XX Administrator's Guide
FigureE-2
Step3. Configure phones on MyPBX auto-provision page.
1. Login MyPBX web interface, „PBX‟ ->„Extensions‟ ->„Phone Provisioning‟
->„Add Phone‟.
FigureE-3
2. Fill in the phone detail message on the pop-up windows.
Input IP Phone‟s MAC address, configure Name, Callwaiting, Line,
Extension,Label, Line active for the phone.And also you can configure other
features on the phone, like codecs, memory keys etc.
www.yeastar.comPage164
MyPBX U5XX Administrator's Guide
FigureE-4
Step4. Turn on the power and connect the network cable to IP Phone.
Remark: The factory default setting of DHCP for IP Phone is enabled, so you
can skip this step to step 5.
If the DHCP is disabled, please follow the stepsbelowto enable it. (e.g.Yealink‟s
IP Phone).
1. Login IP phone‟s web page.
2. Enable DHCP.
www.yeastar.comPage165
MyPBX U5XX Administrator's Guide
FigureE-5
Step5. Finish.
www.yeastar.comPage166
MyPBX U5XX Administrator's Guide
APPENDIX F HowDo I Configure
Distinctive Ring Tones
Step1: On your IP phone, navigate to the Phone settings web configuration
page and find the Distinctive Ring Tone section.
For each custom ring tone, enter the Internal Ringer Text (can be digits or text)
to trigger the ring tone. For example, you may enter “Family”.
e.g.: Yealink‟s IP phone.
FigureF-1
Step2.Configure the „Distinctive Ringtone‟ on MyPBX.
Login MyPBX web interface, „PBX‟ ->„Inbound Call Control‟ ->„Inbound
Routes‟Edit Inbound Route, fill in the Internal Ringer Text on „Distinctive
Ringtone‟.
www.yeastar.comPage167
MyPBX U5XX Administrator's Guide
Figure F-2
Step3. Finish.
www.yeastar.comPage168
MyPBX U5XX Administrator's Guide
APPENDIX G How to Use Email to
SMS
How to use Email to SMS
You need to send an email to the specified email address (you set in Email
Settings. In this case, it is lears@yeastar.com).The content of this email will be
sent to the number you want as message. The subject (title) of the email will
determine the number. Here are some examples of the formats to the subject of
the email.
Example:
1. Send message with no PIN code and default GSM port.
Format: phonenumber
if the subject is "12345678", the text of this email(“Welcome to Yeastar!”) will
be sent to number "12345678" through the first available GSM trunk(No pin
code should be set by administrator).
FigureG-1
2. Send message with no PIN code and specified GSM port.
Format: port:portnumber-phonenumber
if the subject is "port:9-12345678", the text of this email (“Welcome to
Yeastar!”) will be sent to the number "12345678" through GSM trunk 9 (No pin
code should be set by administrator).
www.yeastar.comPage169
MyPBX U5XX Administrator's Guide
FigureG-2
3. Send message with PIN code and default GSM port.
Format: 500:pincodenumber-phonenumber
if the subject is "500:987-12345678", the text of this email(“Welcome to
Yeastar!”) will be sent to number "12345678" through the first available GSM
trunk("987" is the pin code set by administrator).
FigureG-3
4. Send message with PIN code and specified GSM port.
Format: 500:pincodenumber-port:portnumber-phonenumber
if the subject is "500:987-port:9-12345678", the text of this email(“Welcome to
Yeastar!”) will be sent to number "12345678" through GSM trunk 9("987" is
the pin code set by administrator).
FigureG-4
www.yeastar.comPage170
MyPBX U5XX Administrator's Guide
APPENDIX H How to Use DID
Direct inward dialing (DID), also called direct dial-in (DDI) in Europe and
Oceania, is a feature offered by telephone companies for use with their
customers' private branch exchange (PBX) systems. In DID service the
telephone company provides one or more trunk lines to the customer for
connection to the customer's PBX and allocates a range of telephone numbers to
this line (or group of lines) and forwards all calls to such numbers via the trunk.
MyPBX support DID, you can configure DID in inbound route. Related settings:
DID Number, Extension, Destination.
Figure H-1
·
DID Number
Define the expected DID Number if this trunk passes DID on incoming calls.
Leave this field blank to match calls with any or no DID info. Only service
provider, E1 trunks, BRI trunks or SIP trunks need to be configured with this
setting.
You can also use pattern matching to match a range of numbers.The following
patterns may be used:
X: Any Digit from 0-9
Z: Any Digit from 1-9
N: Any Digit from 2-9
www.yeastar.comPage171
MyPBX U5XX Administrator's Guide
[12345-9]: Any digit in the brackets (in this example, 1,2,3,4,5,6,7,8,9)
The „.‟Character will match any remaining digits. For example, 9011. will match
any phone number that starts with 9011, excluding 9011 itself.
The „!‟ will match none remaining digits, and causes the matching process to
complete as soon as it can be determined that no other matches are possible.
·
Extension
Define the extension for DID number, this field only valid when use E1 trunk for
this inbound router.You can only input number and '-' in this field, and the
format can be xxx or xxx-xxx.The count of the number must be only one or
equal the count of the DID number.
·
Destination
If you don‟t set the extension, you can set the destination of the call here.
Example 1:
Step1: You set the DID number (5503XXX in this example).
Step2: You choose the destination(IVR in this example).
The configuration of this example means when the incoming call with DID
number 5503XXX (7 digits number start with 5503) will go to the destination
IVR.
If you choose the destination, please leave the Extension form blank.
www.yeastar.comPage172
MyPBX U5XX Administrator's Guide
Figure H-2
Example 2:
Step1: You set the DID number (6001-6099 in this example).
Step2: You set the Extension (6001-6099 in this example).
The configuration of this example means when the incoming call with DID
number 6001 to 6099 will go to the destination 6001 to 6099(number 6001 to
extension 6001, number 6002 to extension 6002).
The destination you set below will be disabled if you set the Extension.
www.yeastar.comPage173
MyPBX U5XX Administrator's Guide
Figure H-3
www.yeastar.comPage174
MyPBX U5XX Administrator's Guide
APPENDIX I How to Use BLF Key
to Choose the PSTN line
MyPBX allows you to choose the specific PSTN line to make outbound call by
pressing the BLF key on the IP Phone.
Follow the steps to do the configuration with your Yealink phone
1. We want to choose pstn1 or pstn2 to call out.
FigureI-1
2. Configure the IP Phone:
FigureI-2
Test
When you press DSS Key 1/2, the phone will connect to pstn1/pstn2 line. If
pstn1/pstn2 is not busy, you will hear the dial tone. You can dial the number you
want and use this line to call out then.
www.yeastar.comPage175
MyPBX U5XX Administrator's Guide
APPENDIX J How to Enable Auto
Recording
MyPBX U5XX allows you to record the calls automatically. Here is the guide for
you to use it.
J.1 Login
From your web browser, input the IP address of the MyPBX server.
Login the system with the monitor account:
User Name: monitor
Password: password
FigureJ-1
J.2 Recording Settings
1) General Preferences
www.yeastar.comPage176
MyPBX U5XX Administrator's Guide
Enable this function here. You can tick:
a. Record Inbound calls
b. Record Outbound calls
c. Record Internal calls
d. Record Callback calls.
2) Apply To
·
Trunks Recording
When ticked, all calls through the selected trunks will be recorded.
·
Extensions Recording
When ticked, all calls made by the selected extensions will be recorded.
FigureJ-2
J.3 Recording Logs
·
Start Search
You are able to search the record by Start Date to End Date, Extension, Trunk,
Duration and Communication Type.
·
The Record List
You can choose the record to download or delete.
www.yeastar.comPage177
MyPBX U5XX Administrator's Guide
You can check the ID, Time, Callee, Caller, Trunk,
Duration(second),Communication Type of each record
You can play, download or delete the recording files.
FigureJ-3
J.4 Share setting
Use this setting to share the recording file on the network.
·
User Name
The user name to check the file
·
Password
The password to the user name
·
Share Name
The name of the folder showed on the network.
FigureJ-4
www.yeastar.comPage178
MyPBX U5XX Administrator's Guide
For WIN 7/Vista user, please modify the registry before checking the shared
file :
Step1: Start->Run->regedit
Step2: Modify the value of
“HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Lsa\
LmCompatibilityLevel“
to “1”.
If”LmCompatibilityLevel” doesn‟t exit, create a Dword value
“LmCompatibilityLevel“ = 1
You can check the recording file on the network by Explorer/Resource Manager
Run: \\ IP of MyPBX
In the picture below, the IP is 192.168.5.101
FigureJ-5
www.yeastar.comPage179
MyPBX U5XX Administrator's Guide
FigureJ-6
If you change the password of the share folder, the network users may not be
able to check the shared files then.
Please
step1:
step2:
step3:
ask the network user to try:
Start-> Run ->cmd
net use * /del (the is a space behind *)
Visit the device again with new password
J.5 Password Setting
You can change the password of the account “monitor” here.
FigureJ-7
<Finish>
www.yeastar.comPage180
MyPBX U5XX Extension User’s Guide
MyPBX U500/MyPBX U510/MyPBX U520
Extension User’s Guide
Version: V1.1
Yeastar Technology Co., Ltd.
Date: 9th Aug 2013
Yeastar Technology Co., Ltd.(www.yeastar.com)
1/9
MyPBX U5XX Extension User’s Guide
Contents
INTRODUCTION ...................................................................................... 3
1. MYPBX USER WEB INTERFACE .............................................................. 3
1.1 LOGIN .............................................................................................................................................................. 3
1.2 CALL SETTINGS ................................................................................................................................................... 4
1.2.1 Follow Me Settings .................................................................................................................................. 4
1.2.2 Call Waiting ............................................................................................................................................ 5
1.2.3 Do not Disturb (DND) .............................................................................................................................. 5
1.2.4 Ring Out.................................................................................................................................................. 5
1.2.5 Mobility Extension Number ..................................................................................................................... 5
1.3 VOICEMAIL ........................................................................................................................................................ 6
1.3.1 Voicemail Settings ................................................................................................................................... 6
1.3.2 Voicemail Management .......................................................................................................................... 6
1.4 CALL RECORDINGS .............................................................................................................................................. 8
2. CONCLUSION....................................................................................... 9
Yeastar Technology Co., Ltd.(www.yeastar.com)
2/9
MyPBX U5XX Extension User’s Guide
INTRODUCTION
Thanks for using MyPBX U500/MyPBX U510/MyPBX U520 User Web Interface. This Guide would explain how
to configure the “Follow me” settings (in different cases such as, “No Answer”, or “When Busy”; whether
transfer the incoming call to voicemail or other phone number); how to configure Voicemail settings (such as
enable/disable voicemail service, set a voicemail password and enable/disable “send the voicemail to an
email address as an attachment” service); how to manage the extension’s voicemail and call recordings.
1. MYPBX USER WEB INTERFACE
1.1 Login
The default user name and password to log in the User Web Interface:
User Name: Extension number
Password: Voicemail Access PIN#
Note: If it’s unable to log in with default user name and password, please ask the administrator to check
if you have the authority to log in, or have the right user name and password.
Figure 1-1
Yeastar Technology Co., Ltd.(www.yeastar.com)
3/9
MyPBX U5XX Extension User’s Guide
1.2 Call Settings
In the Call Settings page, you could configure features like “Follow me”, “Call waiting”, “DND”, and “Ring
Out”.
Figure 1-2
1.2.1 Follow Me Settings
1. Always
Always Follow Me is a service of MyPBX that allows the automatic unconditional transfer of incoming calls to
varying other destinations.
Enable Always checkbox selection activates the unconditional call forwarding service on the current
extension. The Transfer To displays the destinations where the incoming call from a particular caller should
be unconditionally forwarded to.
a. Transfer To choose voicemail, the incoming call will be unconditionally forwarded to voicemail.
b. Transfer To choose Number, the incoming call will be unconditionally forwarded to other extension, PSTN
or mobile phone number.
Note: When Always Follow Me configuration is save, the Ring Group and Call Queue services will be disabled.
2. No Answer
No Answer Follow Me is a service of MyPBX that allows the automatic transfer of incoming calls to varying
other destinations when the called extension is unable to pick up the call. No answer timeout is configured as
the Ring Out.
Enable No Answer checkbox selection activates no answer call forwarding service on the current extension.
The Transfer To displayed the destinations where the incoming call from a particular caller should be
forwarded to if the called extension is unable to answer the call.
Yeastar Technology Co., Ltd.(www.yeastar.com)
4/9
MyPBX U5XX Extension User’s Guide
a. Transfer To choose voicemail, the incoming call will be forwarded to voicemail when there is no answer.
b. Transfer To choose Number, the incoming call will be forwarded to extension, PSTN or mobile phone
number when there is no answer.
Note: When No Answer Follow Me configuration is saved, the Ring Group and Call Queue services will be
disabled.
3. When Busy
When Busy Follow Me is a service of MyPBX that allows the automatic transfer of incoming calls to varying
other destinations when the called extension is busy with another call.
Enable Busy checkbox selection activates the busy call forwarding service on the current extension.
The Transfer To displayed the destinations where the incoming call from a particular caller should be
forwarded to when the called extension is busy.
a. Transfer To choose voicemail, the incoming call will be forwarded to voicemail when the callee is busy .
b. Transfer To choose Number, the incoming call will be forwarded to other extension, PSTN or mobile phone
number when the callee is busy.
Note: When When Busy Follow Me configuration is saved, the Ring Group and Call Queue services will be
disabled.
1.2.2 Call Waiting
Call Waiting is used to receive an incoming call when already on a call. A ringing tone will be heard by the
caller and a special beeping will be heard on the phone by the MyPBX user when the call arrives. To switch
between the current call and the new incoming call use the appropriate calling code.
Enable Call Waiting checkbox selection activates this service and makes it available for the phone's handset.
Note: If the Call Waiting service is enabled, the Busy Call Forwarding service would be disabled automatically.
1.2.3 Do not Disturb (DND)
Do Not Disturb service is used to turn off the phone bell. If it’s enabled, incoming callers will be routed to the
voicemail box (if enabled); otherwise they will be disconnected automatically.
1.2.4 Ring Out
Ring Out is used to define the ringing time of the extension. If the ringing time exceed the configured time,
the extension would stop ringing.
1.2.5 Mobility Extension Number
Mobility Extension Number is used to enable the cell phone to work as a mobile extension. If a cell phone
number is set as the mobility extension number, once it calls MyPBX, the cell phone would have all authority
of extensions. In this way, the user is able to check the voicemail, call the other extension, PSTN or mobile
numbers via cell phone.
Yeastar Technology Co., Ltd.(www.yeastar.com)
5/9
MyPBX U5XX Extension User’s Guide
1.3 Voicemail
Voicemail is used for the caller to leave a message to the called extension when it is unavailable or busy. The
voicemail would be stored in the extension’s voicemail box. When the caller accesses the voicemail service,
he will hear a voice prompt that remind him to leave a message (This voice prompt could only be configured
by the administrator). The max duration of each voicemail is 15 minutes (The default value is 5 minutes) .
1.3.1 Voicemail Settings
In the Voicemail Settings page, the extension user is able to set the password for voicemail access (which is
the login password of User Web Interface as well); Enable or disable to the voicemail service; enable or
disable “send the voicemail to an email address as an attachment” service.
Set a new voicemail password: Enter the new password, retype it and click “save”.
Email Address: Enter the email address where the voicemail or fax would be sent to as an attachment.
Enable Voicemail: Check the box to enable the voicemail service or uncheck to disable.
Enable Send Voicemail: Check the box to enable “send the voicemail to an email address as an attachment”
service or uncheck to disable.
Figure 1-3
1.3.2 Voicemail Management
In the Voicemail Management page, the extension user could play, delete or download the voicemail, or
move the voicemail from one folder to the other folder (e.g. New, Old, Family, Work, Friends).
Play the voicemail: Select the voicemail the play and click “Play”. In the “Play” page, the user could control
the speed and volume.
Delete the voicemail: Select the voicemail to delete and click “Delete”, then the selected email would be
deleted.
Download the voicemail: Select the voicemail to download and click “download”.
Move the voicemail to another folder: Select the voicemail to move, select the folder to move to (e.g. New,
Old, Family, Work, Friends), and then click “move to”.
Yeastar Technology Co., Ltd.(www.yeastar.com)
6/9
MyPBX U5XX Extension User’s Guide
Figure 1-4
Yeastar Technology Co., Ltd.(www.yeastar.com)
7/9
MyPBX U5XX Extension User’s Guide
1.4 Call Recordings
In the Call Recording page, the user could play, delete and download the recording files.
Play the recording: Select the recording the play and click “Play”. In the “Play” page, the user could control
the speed and volume.
Delete the recording: Select the recording to delete and click “Delete”, then the selected email would be
deleted.
Download the recording: Select the recording to download and click “download”.
Figure 1-5
Yeastar Technology Co., Ltd.(www.yeastar.com)
8/9
MyPBX U5XX Extension User’s Guide
2. CONCLUSION
This User’s Guide only explains the configuration of call settings and voicemail settings; management of
voicemails and recordings for extension users. For more functionality and advanced settings of MyPBX
U500/MyPBX U510/MyPBX U520, please refer to the relative documents as below:
“MyPBX U500 Datasheet”
“MyPBX U500 Quick Installation Guide”
“MyPBX U500 Administrator’s Guide”
“MyPBX U510 Datasheet”
“MyPBX U510 Quick Installation Guide”
“MyPBX U510 Administrator’s Guide”
“MyPBX U520 Datasheet”
“MyPBX U520 Quick Installation Guide”
“MyPBX U520 Administrator’s Guide”
[The End]
Yeastar Technology Co., Ltd.(www.yeastar.com)
9/9