Oki lan 6020E User's Manual

Add to my manuals
226 Pages

advertisement

Oki lan 6020E User's Manual | Manualzz
OkiLAN 6020e® Pocket Print Server
User’s Guide
High Performance 10/100 Base-T Ethernet
Network Print Server
Copyright and Trademark Information
Every effort has been made to ensure that the information
in this document is complete, accurate, and up-to-date.
Oki Data assumes no responsibility for the results of
errors beyond its control. Oki Data also cannot guarantee
that changes in products made by other manufacturers
and referred to in this handbook will not affect the
applicability of the information in it. This handbook is
subject to change without notification.
© 2000 by Oki Data. All rights reserved.
Oki Data, OKIPAGE, OkiVIEW, OkiLAN Reg. T.M.,
M.D.,., and OKICOLOR T.M., OKI Electric Industry Co.,
Ltd.; Windows, MS-DOS Reg. T.M., Microsoft Corp.; HP
LaserJet, PCL, Reg. T.M. Hewlett Packard Company;
Centronics Reg. T.M., Centronics Data Computer Corp.;
Energy Star, Reg. T.M., U.S. EPA; Ethernet Reg. T.M.
Digital Equipment Corp.; Adobe Reg. T.M., PostScript
T.M., Adobe Systems Inc.; Macintosh EtherTalk,
LocalTalk, TrueType Reg. T.M. , Apple Computer Inc.;
Novell, NetWare, Unix, YES NetWare Tested and
Approved logo, Reg. T.M. Novell Corp.; ProPrinter, OS/2
Reg. T.M. TokenRing, T.M., International Business
Machines Corp.
ii
OKI OkiLAN 6020e User’s Guide
Organization and Contents
Organization
This manual has been divided into eight sections. Section
I contains and installation instructions for the OkiLAN
6020e print server.
Section II contains information about management
features, an extremely valuable set of OkiLAN 6020e
management tools for network administrators.
The Network Operating System (NOS) and protocol
sections are found in Sections III through VI.
Section VII contains information and instruction on
Windows printing options. With the exception of the
Advanced Management Features section, each section in
this manual has been designed to be independent of one
another.
Contents
Section I: Hardware Installation .............................. I-1
Section II: Advanced Management Features ........ II-1
Chapter 1: SNMP ......................................................... II-3
Chapter 2: HP JetAdmin Support ................................. II-6
Chapter 3: HP Web JetAdmin Support ......................... II-8
Chapter 4: OkiLAN 6020e Web Configuration .......... II-10
Chapter 5: Additional Management Features .............. II-18
Section III: Novell NetWare .................................... III-1
Chapter 1: Introduction ................................................ III-4
Chapter 2: OkiNet for NetWare ................................... III-6
Chapter 3: OkiNet for NDS ...................................... III-24
Chapter 4: Using the OkiLAN 6020e in NDPS
(NetWare 4.x and 5.1) ............................................... III-33
OKI OkiLAN 6020e User’s Guide
iii
Organization and Contents
Section IV: TCP/IP .................................................. IV-1
Chapter 1: Introduction ................................................ IV-5
Chapter 2: Configuring the OkiLAN 6020e ................ IV-7
Chapter 3: TCP/IP Configuration and Printing .......... IV-14
Chapter 4: OkiNet for TCP/IP ................................... IV-23
Chapter 5: Web Configuration ................................... IV-42
Chapter 6: Telnet Configuration ................................. IV-43
Appendix A: Troubleshooting ................................... IV-49
Appendix B: Application Considerations .................. IV-56
Appendix C: Internet Printing Protocol (IPP) ........... IV-81
Section V: LAN Manager/LAN Server ................... V-1
Chapter 1: Introduction ................................................. V-3
Chapter 2: Installation ................................................... V-5
Chapter 3: Printing in the OS/2 Environment ............. V-11
Chapter 4: Additional Utility Features ........................ V-13
Chapter 5: Using Help ................................................ V-16
Appendix A: Troubleshooting .................................... V-17
Section VI: EtherTalk ............................................. VI-1
Chapter 1: Introduction ............................................... VI-3
Chapter 2: The OkiLAN 6020e Utility ....................... VI-4
Appendix A: Troubleshooting .................................... VI-8
Appendix B: Selecting Your Printer ......................... VI-13
Appendix C: Capturing With a Spooler .................... VI-14
Section VII: Windows Printing............................. VII-1
Chapter 1: OkiLAN 6020e Set Up
for Windows NT 4.0/2000 ........................................ VII-3
Chapter 2: OkiLAN 6020e Set Up
for Windows 95/98 ................................................. VII-10
Section VIII: OkiView 32 ...................................... VIII-1
Chapter 1: Introduction ............................................. VIII-3
Chapter 2: OkiView 32 Printer Panel ....................... VIII-4
Section IX: Regulatory Information ..................... IX-1
Index
iv
OKI OkiLAN 6020e User’s Guide
Network Operating Systems
Network Operating Systems
Overview
OkiLAN 6020e simultaneously supports several network
protocols in various combinations. Below is a list of
supported network protocols accompanied with NOS/OS
requirements.
TCP/IP and Windows NT
TCP/IP, FTP and Remote LPD protocols. Simple Network
Management Protocol (SNMP) and Windows NT are
supported in this environment. HTTP and a built-in Web
server are standard for the 6020e.
Novell NetWare
Novell NetWare versions 3.x, 4.1, 5.x and higher.
EtherTalk
Macintosh® System 6.x or later and LaserWriter® Driver
version 8.x.
LAN Manager/LAN Server
OS/2 version 1.3 with LAN Manager version 2.x and OS/
2 version 1.3 or higher with LAN Server version 2.x and
higher.
OKI OkiLAN 6020e User’s Guide
v
Technical Support
Service Information
Note: This information is valid for the United States and
Canada only.
Oki Data On Line
Visit the OKI DATA Web Site at http://www.okidata.com for
the latest information on:
• Software drivers
• Product guides
• Customer support
• Corporate information
• Dealers
• Documentation
Your Dealer
Consult the store where you purchased your OkiLAN
6020e, or call 1-800-OKI-DATA (1-800-654-3282) for
the location of the nearest authorized Oki Data service
dealer. Have your ZIP code ready.
• Proof of purchase is required for warranty work. Be
sure to retain your purchase documents.
• Prices and minimum charges may vary.
The Oki Data Customer Support Center
For customer support, call 1-800-OKI-DATA (800-6543282). The Oki Data Information System Automated
Attendant is available 24 hours a day, 7 days a week. The
system can provide immediate assistance with:
• Basic operating procedures
• Sales and service referrals
• Parts and consumable referrals
• Product information
vi
OKI OkiLAN 6020e User’s Guide
Technical Support
Oki Data Customer Support Representatives
Agents are available 24 hours a day, 7 days a week at
1-800-OKI-DATA (1-800-654-3282). Please be sure that
you are calling from a telephone close to your printer, so
you can describe your problem accurately. Our customer
service representatives are trained on all current Oki Data
products They can answer your questions regarding:
• Installation
• Determination of printer issues that require service
• Consumer relations
• Interface information
• Availability and installation of printer drivers and
support for the latest network operating systems.
(Customer service representatives are not trained to
provide assistance with the use of commercial software
packages. Please consult your software user’s manual
for times and availability of their support).
Oki Data Service Centers
Oki Data has over 2,000 local Authorized Service
Providers in North and South America.
For the most comprehensive, up-to-date listing of Oki
Data authorized Service Centers:
- Consult our web site at www.okidata.com
- In the U.S. and Canada, call 1-800-654-3282 (1-800OKI-DATA) English and French only.
- In Latin America, contact the Latin America Service
Coordinator at Oki Data’s Corporate
Headquarters at 856-235-2600 (Spanish only).
United States
Oki Data Americas, Inc.
Tel: 1-800-OKI-DATA (800-654-3282)
Fax: 1-856-222-5247
Canada
Oki Data Americas, Inc.
Tel: 1-800-OKI-DATA (800-654-3282)
Fax: 905-238-4427
OKI OkiLAN 6020e User’s Guide
vii
Technical Support
Brazil
Oki Data do Brasil, Ltda.
Tel: 0800-11-5577
Fax: 55-11-5012-0267
Mexico
Oki Data de Mexico, S.A. de C.V.
Tel: 525-263-8780
Fax: 525-250-3501
viii
OKI OkiLAN 6020e User’s Guide
Technical Support
When you call Technical Support, the following
information will help us answer your questions more
quickly and accurately. Please be able to identify the
following:
• OkiLAN model number
• Serial number
• Configuration sheet settings
• Type of network cable connected to the OkiLAN 6020e
• Printer(s) make and model numbers
• Computer and network adapter card make and model
numbers
• Network Operating System and version number
Please write these numbers down in the space provided
below for future reference.
Model #:
S/N:
___________________
___ ___ ___ ___ ___ ___ ___
Ethernet ADDR:
00:40:68: ___ : ___ : ___
OKI OkiLAN 6020e User’s Guide
ix
Technical Support
x
OKI OkiLAN 6020e User’s Guide
Hardware Installation
Section I:
Hardware
Installation
Section I - Hardware Installation
I-2
OKI OkiLAN 6020e User’s Guide
In This Section
Powering On the OkiLAN 6020e ................ I-7
Printing a Configuration Sheet ..................... I-8
OKI OkiLAN 6020e User’s Guide
I-3
Hardware Installation
Section I - Hardware Installation
Section I - Hardware Installation
I-4
OKI OkiLAN 6020e User’s Guide
The OkiLAN 6020e Pocket Print Server enables
Ethernet network users to connect to a printer with a
bidirectional parallel port. The OkiLAN 6020e can be
made to work with any Centronics or IEEE-1284 parallel interface printer that includes a resident emulation
such as PCL versions 4 through 6, Adobe PostScriptâ,
IBM ProPrinterâ or Epsonâ emulations.
The OkiLAN 6020e supports 10/100-megabit networks
and most popular network operating systems and printers, except for the OKIPAGE 8z and other GDI-based
printers.
The OkiLAN 6020e kit includes the following:
·
·
·
·
·
OkiLAN 6020e hardware
Power adapter with line cord
Installation User’s Guide
Utilities CD
Product registration card
Installing the OkiLAN 6020e
1. Turn off printer power.
2. Attach the OkiLAN 6020e to the centronics connector on your printer.
Parallel
connector
OKI OkiLAN 6020e User’s Guide
I-5
Hardware Installation
Section I - Hardware Installation
Section I - Hardware Installation
3. Secure the OkiLAN 6020e with the wire clips on the
printer’s connector.
4. Plug the power adapter wire into the power jack on
the OkiLAN 6020e. Then plug the power adapter
into a 120 VAC wall outlet.
Please note that some countries may require a
different adapter for local voltages, such as 240
VAC.
I-6
OKI OkiLAN 6020e User’s Guide
5. Attach the 10/100Base-T UTP cable to the receptacle on the back of the OkiLAN 6020e.
Attach the other end of the cable to the Network.
Powering On the OkiLAN 6020e
Turn printer power on. The red and green indicators on
the OkiLAN 6020e will blink during self-test. When
self-test completes successfully, the red indicator will go
off and the green indicator will stay on.
Green indicator
Red indicator
OKI OkiLAN 6020e User’s Guide
I-7
Hardware Installation
Section I - Hardware Installation
Section I - Hardware Installation
Note: If the red and green indicators do not display as
indicated above, see Hardware Troubleshooting at the
end of this section.
Printing a Configuration Sheet
To print configuration information, press the Test button
on the front of the OkiLAN 6020e. You can also print
configuration information using the utility program
provided on the CD.
Note: By default, the configuration sheet prints in
ASCII text. If you want the configuration sheet to print
in PostScript or PCL, select this option (if the emulation
is supported in the printer) when you run the network
configuration utility program. The selected language
must match the printer’s configured language to print
correctly.
The content of the configuration sheet will vary depending on your printer and system setup.
I-8
OKI OkiLAN 6020e User’s Guide
Installing the OkiLAN 6020e
Software Utilities
Introduction
Your OkiLAN 6020e Pocket Print Server comes with
two types of software utilities: OkiView 32 and OkiNet
Utilities.
OkiView 32
OkiView 32 is a general purpose utility for configuring
and montioring printers on NetWare and Windows NT/
2000 servers. It includes a GUI for the Win32
(Windows) environment. For more information on using
OkiView 32, see section VIII.
OkiNet Utilities
The OkiNet utilities are specialty utilities used in different operating systems such as Unix, Mac and Win32.
A custom port monitor utility is also provided for the
Win32 environment which supports peer-to-peer
printing, also known as serverless printing. TCP/IP, DLC
and IPX-direct protocols are supported in this serverless
network environment. See Section VII, Windows Printing, for details.
OKI OkiLAN 6020e User’s Guide
I-9
Hardware Installation
Section I - Hardware Installation
Section I - Hardware Installation
Installing the OkiLAN Utilities
Software in Windows
1. Insert the OkiLAN CD into your CD-ROM drive.
2. The Setup screen appears automatically (if it doesn’t,
click Start®Run, then enter D:\setup, if “D” is your
CD-ROM drive).
3. Select the utility group for the network environment
you have, then click Next.
4. Select the specific utility you want to install and the
proper location for installation, then click Install.
Windows Utility Groups:
NetWare Management Utilities
OkiNet Utility for NetWare
OkiNet Utility for NDS (Workstation and Server)
OkiNet Utility for NDS (Workstation)
OkiNet Connect Windows Printing
OkiNet Connect for TCP/IP (Windows 95/98)
OkiNet Connect for TCP/IP (Windows NT)
OkiNet Connect for IPX/SPX (Windows 95/98)
OkiNet Connect for IPX/SPX Windows NT)
OkiNet Connect DLC (Windows 95/98)
OkiNet Connect DLC (Windows NT)
TCP/IP Management Utilities
OkiNet Utilities for TCP/IP
OkiNet Alert for TCP/IP
Okidata MIB
BootP Server
I - 10
OKI OkiLAN 6020e User’s Guide
Apple® MacIntosh® Utility Groups:
OkiNet for the Apple® MacIntosh®
Utility
Note: The OkiLAN Utilities CD is designed for more
than one type of OkiLAN print server and includes
features that do not apply to the OkiLAN 6020e. Specifically, Apple EtherTalk is supported by other OKI print
servers but not by the OkiLAN 6020e.
Installing OkiView 32
Note: Novell’s Client for Windows 95/98, NT or 2000 is
required for OkiView 32. Microsoft Client is required
only for configuring Novell using a Microsoft network.
Insert the OkiView 32 CD into your CD-ROM drive and
run Setup.exe.
OKI OkiLAN 6020e User’s Guide
I - 11
Hardware Installation
Section I - Hardware Installation
Section I - Hardware Installation
Hardware Troubleshooting
Status Indicator
The LED status indicators display the general operating
state of the OkiLAN 6020e. During normal operation,
the red LED is off and the green LED is on, indicating
that the OkiLAN 6020e is functioning properly and the
presence of the network is detected.
The following list describes LED displays that indicate
problems, as well as possible solutions:
LED Display
Green indicatior flashing very rapidly
Problem
The OkiLAN 6020e has not detected the presence of a
network cable.
Solution
a) Unplug the OkiLAN 6020e power adapter from the
wall outlet. Remove the network cable. Plug the
network cable back in until you hear a positive click.
Check the other end of the cable in the same manner.
Plug the OkiLAN 6020e back in. If it does not detect
a cable, continue below.
b) Verify the cable is a 10/100 Base-T cable and it has
an RJ-45 end. The network cable must have a cat-3
or higher rating. Silver Satin or flat ribbon cable is
not adequate.
c) Connect to a network that a currently working PC or
print server is using. If the OkiLAN 6020e is still
unable to detect the network cable, contact Technical
Support for assistance.
I - 12
OKI OkiLAN 6020e User’s Guide
LED Display
Green indicator is flashing slowly (1 timer/sec);
the OkiLAN 6020e is trying to print a job.
Problem
The printer is malfunctioning or does not have sufficient
paper or toner.
Solution
Verify that the printer is not showing any errors and has
sufficient paper and toner.
LED Display
Red indicator is stays red for more than 30 seconds
Problem
The printer server has failed the Power On Self Test.
Solution
The OkiLAN 6020e will try to print a configuration
sheet on the printer with more information.
Failing the self test can be caused by any of the following:
a) The printer is malfunctioning. Unplug the OkiLAN
6020e from the printer and unplug the power adapter.
Reconnect the OkiLAN 6020e and the power
adapter. If the OkiLAN 6020e still fails the self test,
continue below.
b) The OkiLAN 6020e power supply has failed or there
is a hardware problem. Contact Okidata Customer
Support for replacement information.
OKI OkiLAN 6020e User’s Guide
I - 13
Hardware Installation
Section I - Hardware Installation
Section I - Hardware Installation
LED Display
The red and green indicators are alternately flashing for
longer than two minutes.
Problem
The OkiLAN 6020e is in firmware download mode.
This means it is waiting for new firmware to be sent
before it will continue functioning normally.
Solution
If the OkiLAN 6020e was purposely put into firmware
download mode, finish the download with the proper
update utility. Contact our web site at
http://www.okidata.com to download the utility.
I - 14
OKI OkiLAN 6020e User’s Guide
Advanced
Management
Features
Advanced Management
Section II:
Section 2 - Advanced Management Features
In This Section
Chapter 1 SNMP ......................................................II-3
Overview ....................................................... II-3
Private MIB ................................................... II-3
Traps .............................................................. II-4
Security .......................................................... II-5
Chapter 2 HP JetAdmin Support ............................II-6
Overview ....................................................... II-6
Configuring the OkiLAN 6020e
Using JetAdmin ........................................... II-6
Chapter 3 HP Web JetAdmin Support ...................II-8
Overview ....................................................... II-8
Configuring the OkiLAN 6020e Using
Web JetAdmin ............................................. II-8
Installing a Windows NT Printer for the
OkiLAN 6020e ............................................ II-8
Obtaining Diagnostic Information from
the OkiLAN 6020e ...................................... II-9
Chapter 4 OkiLAN 6020e Web Configuration .....II-10
Overview ..................................................... II-10
Connecting to the OkiLAN 6020e ............... II-10
Configuration ............................................... II-12
Status ............................................................ II-15
Print Job Log ............................................... II-15
Support ......................................................... II-15
Reset ............................................................ II-16
OkiLAN 6020e Server Discovery ............... II-16
Troubleshooting ........................................... II-17
Chapter 5 Additional Management Features ......II-18
OkiNet Alert ................................................. II-18
Enhanced Printer Status ............................... II-18
OkiNet for NDS ........................................... II-19
OkiNet for TCP/IP (Creating Custom
Views) ........................................................ II-19
NetWare Load Balancing ............................. II-19
Windows Printing ........................................ II-19
Printer Security for TCP/IP Printing ............ II-19
II - 2
OKI OkiLAN 6020e User’s Guide
Section 2 - Chapter 1 - SNMP
Overview
Simple Network Management Protocol (SNMP)
provides network administrators with the ability to
communicate management functions between an SNMP
manager and an SNMP agent. An SNMP manager is a
user program the network administrator can use to
manage SNMP agents. The manager can retrieve Get
information from the agent or alter Set information on
the agent. An agent can also send an unsolicited
message Trap to a manager when it encounters an
unusual condition.
The OkiLAN 6020e is a fully functional SNMP agent
and supports any standard SNMP management
platform, including:
• HP OpenView
• Novell NMS
• Sun SunNet Manager
• IBM NetView
Private MIB
OkiLAN 6020e SNMP support has been enhanced with
a private MIB. It is accessible via SNMP over TCP/IP
and IPX. This private MIB contains over 150
configuration and status variables for the network
protocols, printer ports, network interfaceprinter
settings, and the overall OkiLAN 6020e status. Printer
status traps such as on-line, off-line, detached printer
and printer error are also provided.
The setting of certain variables causes an immediate
firmware reset. These variables are listed in the private
MIB under cmdReset.
OKI OkiLAN 6020e User’s Guide
II - 3
Advanced Management
Chapter 1
Simple Network Management
Protocol (SNMP)
Section 2 - Chapter 1 - SNMP
Note: If you attempt a reset while a job is printing, the job
may not print successfully.
Certain variables are critical, that is, they change a
fundamental operating parameter of the OkiLAN
6020e. These variables are saved by the OkiLAN
6020e but are not actually used until it is power cycled
or is reset. When any one of these variables is changed
the variable genConfigDirty is automatically set to yes
by the print server. This signifies a reset is required for
all configuration changes to be made active. We
recommend checking the genConfigDirty variable after
using a MIB browser to make any configuration
changes to the OkiLAN 6020e. If genConfigDirty is set
to yes, then the cmdReset variable should also be set to
yes. This will cause the OkiLAN 6020e to reset, make
all configuration changes active on the OkiLAN 6020e
and set both the cmdReset and genConfigDirty
variables to no. These critical variables are listed in the
private MIB under genConfigDirty.
Traps
Traps are unsolicited information from the SNMP
agent. The OkiLAN 6020e uses a ColdStart trap to
inform the manager it has been powered on or reset. An
authentication failure trap is sent when the OkiLAN
6020e receives an SNMP trap GET or SET request with
an incorrect community name.
The OkiLAN 6020e sends printer traps when there is a
change in the status of the printer. If the Printer goes
off-line, runs out of paper or is detached, the
administrator will be notified via the OkiLAN 6020e
traps over both UDP and IPX. Additionally, the
OkiLAN 6020e can send traps on toner low, paper jam,
and printer cover open, depending on the printer’s
capabilities. The traps may be configured for specific
destination addresses and can be configured for a
particular printer port and/or printer trap.
II - 4
OKI OkiLAN 6020e User’s Guide
In order to receive OkiNet Alert traps, the OkiLAN
6020e must have bi-directional status enabled (it is
disabled by default). Extended Status can be enabled
through the OkiLAN 6020e Configuration utility
(telnet) from the Configure Port option. You can also
enable OkiNet Alert through OkiNet for TCP/IP or IPX
from the Output Port file tab.
Security
SNMP implements a simple security system known as
community names. Each SNMP message has a
community name associated with the command in the
message. SNMP allows for a Set community name, Get
community name and a Trap community name. When
the SNMP Agent receives a command, it checks the
community name of the message with the community
name of the device. If the community names do not
match, the Agent discards the message and sends an
authentication failure trap.
Both the OkiNet for TCP/IP and the IPX, and the
OkiLAN 6020e Configuration utility (telnet) allow you
to specify the community names and a trap destination
IP address.
OKI OkiLAN 6020e User’s Guide
II - 5
Advanced Management
Section 2 - Chapter 1 - SNMP
Section 2 - Chapter 2 - HP JetAdmin Support
Chapter 2
HP JetAdmin Support
Overview
This section contains instructions and information on
how to configure and obtain diagnostic information
from your OkiLAN 6020e using the Hewlett-Packard
JetAdmin software.
Software Requirements
• JetAdmin 2.4, 2.5, or 3.02
• Windows 95/98 or Windows NT/2000
Note: For more information on installing and using
HP JetAdmin, refer to the HP JetAdmin
documentation.
Configuring the OkiLAN 6020e Using
JetAdmin
NetWare Configuration
1. From the main JetAdmin screen, select the OkiLAN
6020e port you wish to configure.
2. Select Modify from the Device menu.
3. On the Configuration screen, select the General tab
and enter the print server name and description.
4. Select the NetWare tab and click on the Operating
Mode icon from the left column. Set the print server
operating mode from the given options on the right.
5. If you are running a NetWare 4.x network, click the
NetWare Directory Services icon from the left
column. Select NDS Tree Name from the pull-down
menu and enter the Print Server Context.
6. Click the Queues icon from the left column to bring
up the Queues screen and then click the Change
button.
II - 6
OKI OkiLAN 6020e User’s Guide
Section 2 - Chapter 2 - HP JetAdmin Support
WARNING: Do not use both OkiNet and JetAdmin to
change NetWare configuration settings as unexpected
results may occur.
TCP/IP Configuration
1. From the main JetAdmin screen, select the OkiLAN
6020e port you wish to configure.
2. Select Modify from the Device menu.
3. On the Configuration screen, select the General tab
and enter the print server name and description.
4. Select the TCP/IP tab and set the print server IP
configuration.
AppleTalk Configuration
1. From the main JetAdmin screen, select the OkiLAN
6020e port you wish to configure.
2. Select Modify from the Device menu.
3. Under the Optional tab, select Mac.
4. Enter the Apple Talk name and click OK.
Obtaining Diagnostic Information Using JetAdmin
1. From the main JetAdmin screen, select the OkiLAN
6020e port on which you wish to view diagnostic
information.
2. Select Properties from the Device menu.
3. From the Properties screen, select the appropriate
tab to view the desired diagnostic information.
Note: For JetAdmin to function correctly with the
OkiLAN 6020e, the SNMP Get community
name in JetAdmin must be set to public.
OKI OkiLAN 6020e User’s Guide
II - 7
Advanced Management
7. Select the desired queues from the list of Available
Queues to be added into service. Click the Service
button to move the selection to the Serviced Queues
column. When all queues have been added, click
OK.
8. Click OK again to return to the main screen.
Section 2 - Chapter 3 - HP Web JetAdmin Support
Chapter 3
HP Web JetAdmin Support
Overview
This section contains instructions and information on
how to configure, install, and obtain diagnostic
information from your OkiLAN 6020e using the
Hewlett-Packard Web JetAdmin software.
Software Requirements
• Web JetAdmin 1.x, 2.x, 3.x, or 4.x
Note: For more information on installing and using
HP Web JetAdmin, refer to the HP Web
JetAdmin documentation.
Configuring the OkiLAN 6020e Using
Web JetAdmin
1. From the main Web JetAdmin page, select the
OkiLAN 6020e port you wish to configure.
2. On the Properties page, click the Config button.
3. Make any necessary changes to the options listed
and click the corresponding Apply button.
Installing a Windows NT Printer for
the OkiLAN 6020e
1. From the main Web JetAdmin page, select the
OkiLAN 6020e port you wish to install.
2. On the Properties page, click the Install Printer
button.
3. In the Specify the device address… field, enter the
print server IP address, followed by a comma and
then the output port number. For example, to install a
printer for output port 2 of an OkiLAN 6020e with
an IP address of 10.10.10.2, enter “10.10.10.2,2”.
II - 8
OKI OkiLAN 6020e User’s Guide
4. On the Install Printer Page 1 page, select an NT
domain from the pull-down menu. Enter the user
name and password of a domain user with sufficient
rights to create a printer and click the Continue
button.
5. On the Install Printer Page 2 page, select the
Windows NT machine from the pull-down menu on
which you want to create the shared printer and click
the Continue button.
6. On the Install Printer Page 3 page, select a printer
driver from the pull-down menu and click the
Continue button.
7. On the Install Printer Page 4 page, enter a name for
the printer in the Select Printer Name field and click
the Install Printer button.
8. Users in the domain can now print to the new printer.
Obtaining Diagnostic Information
from the OkiLAN 6020e
1. From the main Web JetAdmin page, select the
OkiLAN 6020e port on which you wish to view
diagnostic information.
2. Click the Diagnose button.
3. From the Properties page, select the appropriate
diagnostic category name to view information.
OKI OkiLAN 6020e User’s Guide
II - 9
Advanced Management
Section 2 - Chapter 3 - HP Web JetAdmin Support
Section 2 - Chapter 4 - OkiLAN 6020e Web Configuration
Chapter 4
OkiLAN 6020e Web
Configuration
Overview
This section contains instructions and information on
how to configure and manage your OkiLAN 6020e
using a standard Web browser.
Software Requirements
TCP/IP Protocol
Netscape Navigator 2.0 or greater and Microsoft
Explorer 3.0 or greater (Other browsers may work).
Note: If you experience difficulties connecting to the
server, refer to Appendix A, Troubleshooting.
Connecting to the OkiLAN 6020e
1. Enter http://<HTTP Address> in the browser
address prompt.
The HTTP address can be the IP address, the System
Name if the print server has been configured to use
WINS, or the DNS name if registered with a DNS
server.
Note: It is not currently possible to discover all
OkiLAN 6020e products from a Web browser.
If you need to create a list of all available
OkiLAN 6020e products and their addresses,
refer to the OkiLAN 6020e Product Discovery
section for instruction.
II - 10
OKI OkiLAN 6020e User’s Guide
Note: As a layer of security, the TCP port number
that the device uses to communicate with
browsers, called the HTTP port, can be
modified from a default of 80. If the port is
modified, the HTTP address put in the browser
must include the port number, for example,
http://vpn.company.com:99/ would be entered
for port 99. Refer to the Web Admin
Configuration section for details.
2. A successful connection will display the print server
home page.
Note: By default, only Status and Support
information can be viewed. To configure the
print server, see the Configuration section.
The print server pages are normally displayed in a
frame with two panes. The left pane shows all the top
level menus along with links to the pages under each
menu. The right pane displays the currently selected
page. If your browser does not support frames, or you
select the No Frames link at the bottom of the left pane,
a single page will be displayed. In this case, the menu
items normally shown in the left pane can be accessed
by using the menu links that appear at the bottom of the
page.
OKI OkiLAN 6020e User’s Guide
II - 11
Advanced Management
Section 2 - Chapter 4 - OkiLAN 6020e Web Configuration
Section 2 - Chapter 5 - Additional Management Features
Configuration
1. Select the Login as Admin link under the
Configuration menu.
2. On the Enter Network Password screen, enter the
User name and Password.
The default administrator User name is admin. The
default administrator Password is OkiLAN—note
that the password is case sensitive. We suggest that
the print server administrator change the default
administrator User name and Password. New User
name and Password entries can contain up to 24
characters.
3. Select the appropriate link under the Configuration
menu and modify the desired values on the page that
appears.
Note: All values (except as noted on the following
pages*) are configured exactly the same as in
the OkiNet utility. Please refer to the OkiLAN
6020e User’s Guide Section IV - TCP/IP,
Chapter 4 - OkiNet for TCP/IP for instructions
on configuration.
4. Select the Submit Changes button at the bottom of
the page to send the new values to the print server.
WARNING: Changes will not be saved if the Submit
Changes button is not selected before continuing to
another page.
II - 12
OKI OkiLAN 6020e User’s Guide
5. A Request Results page will appear indicating one of
the following:
• Configuration Successfully Set: The values have
been successfully saved to the print server. Go to
another page to continue configuration or exit the
browser.
• Invalid Input: Some or all input fields contain
invalid information. None of the values have been
saved to the print server. The Request Results
page will list all fields that contain errors along
with a description of the problem. Selecting the
Back button on your browser will generally
redisplay the page you just submitted and allow
the values to be edited. Selecting the Reload link
on the Request Results page will produce a new
entry page from the server so you can start over.
• Configuration Successfully Set. Reset
Required: The values have been successfully
saved, but the print server must be reset for the
desired values to take effect. Reset the server
immediately or wait until all configuration is
complete before resetting. If you do not reset
immediately, a link will appear at the top of all
subsequent configuration pages reminding you to
reset the server.
OKI OkiLAN 6020e User’s Guide
II - 13
Advanced Management
Section 2 - Chapter 4 - OkiLAN 6020e Web Configuration
Section 2 - Chapter 5 - Additional Management Features
* The following values are currently only
configurable through the Web browser
interface:
Web Admin Configuration
Under the Configuration menu, select the Admin(Web)
link.
• Admin Name - The name used to access full
configuration privileges. The default Admin
Name is admin.
• Admin Password - This field is used to specify
the Admin Password used to access full
configuration privileges. This field will
accommodate up to 24 characters. The default
Admin Password is OkiLAN-note that the
password is case sensitive.
Note: The Admin Password is also used as the Telnet
password.
• Confirm Admin Password - This field is used to
confirm the Admin Password entry by entering a
second time.
• HTTP Port - This field is used to specify the TCP
port that the HTTP protocol will listen on. The
default HTTP port is 80, but can be changed to
provide added security.
• FAQ URL - By default points to the FAQ page on
the OKI Web Server. Maximum URL length is 63
characters.
• Updates URL - By default points to the firmware
update site on the OKI FTP Server. Maximum
URL length is 63 characters.
• Custom Link Title - This field is useful for
setting up a link to an internal help desk. If
configured, it will appear under the Support
menu. Will accommodate up to 24 characters.
• Custom Link URL - This field is useful for
setting up a link to an internal help desk. Can
contain any URL up to 63 characters.
II - 14
OKI OkiLAN 6020e User’s Guide
Section 2 - Chapter 4 - OkiLAN 6020e Web Configuration
The home page for the print server shows general status
information including the status of all printers currently
attached. For more detailed status information, select
the View Cnfg Sheet link under the Status menu. This
will show information similar to what is printed on the
print servers configuration sheet.
Print Job Log
The Print Job Log page provides information on print
jobs, system up time and total jobs printed.
Support
There are up to four links listed under the Support
menu.
Contact
This page provides the necessary addresses and phone
numbers for contacting Oki Data Customer Support.
FAQ
By default this link will connect you to the FAQ page
on the OKI Web Server. This link can be configured to
point to other locations by selecting the Admin(Web)
link under the Configuration menu.
Updates
By default this link will connect you to the firmware
update location on the OKI FTP Server. This link can
be configured to point to other locations by selecting
the Admin(Web) link under the Configuration menu.
Custom Link
This link will only appear if it has been configured by
selecting the Admin(Web) link under the
Configuration menu. This link can be used to access
internal help desk sites.
OKI OkiLAN 6020e User’s Guide
II - 15
Advanced Management
Status
Section 2 - Chapter 5 - Additional Management Features
Reset
Reset
Reset the print server by selecting the Reset link under
the Reset menu. A message will appear asking you to
confirm the reset.
Restore
Select Restore Defaults under the Reset menu to
restore selected protocols to factory defaults. Select the
individual protocols to be restored and then select the
Restore Selected Protocols button. All protocols can
be restored simultaneously by selecting the Restore All
Protocols button.
OkiLAN 6020e Server Discovery
An HTML file containing links to all OkiLAN 6020e
print servers on the network can be created using the
OkiNet utility for TCP/IP. Complete the following steps
to create the HTML file:
1. Install and run the OkiNet for TCP/IP utility. The
utility will discover and display all OkiLAN 6020e
printservers on the local network.
2. Create a custom view, if desired, to control which
devices are displayed. See Creating Customized
Views in the OkiLAN 6020e Users Guide, Section
IV.
3. Select Save View to HTML under the File menu.
4. Enter a name and save the file.
5. From the Web browser, select Open under the File
menu and enter the path and name of the file saved
in step 4.
6. You can now create a bookmark or add the file to
your list of favorites.
Note: This file does not update automatically. The
OkiNet utility must be run again to obtain
current information.
II - 16
OKI OkiLAN 6020e User’s Guide
Section 2 - Chapter 4 - OkiLAN 6020e Web Configuration
Troubleshooting
• The print server only supports two simultaneous
HTTP connections. If your browser fails to connect
to the print server, the browser may be trying to open
more than two connections. Please refer to your
browser’s Help files for information on changing the
connection settings. Both Netscape Navigator and
Microsoft Explorer for the Macintosh and Power PC
will sometimes display a failure to connect message
after being configured for only two connections.
Should this occur, select OK to bypass the error
message. The menu page will still be displayed and
configuration can be completed.
• Quickly refreshing a page within some browsers can
cause the browser to leave active connections open
with the server called a hung connection. This will
use up one of the HTTP connections, can cause
problems connecting to the server and will slow
down Web response time. If TCP timeout checking
is enabled under TCP/IP configuration, the hung
connection will timeout after the timeout period has
expired.
Login
• If you forget the administrator password, restoring
the TCP/IP protocol to factory defaults from any
other configuration utility restores the Web admin
name and password to default values.
Configuration
• Web browsers will generally cache previously
viewed Web pages on the local machine. To view the
most current print server information, it is a good
idea to select the Reload or Refresh button on your
browser instead of using the Back button.
OKI OkiLAN 6020e User’s Guide
II - 17
Advanced Management
Server Connection
Section 2 - Chapter 5 - Additional Management Features
Chapter 5
Additional Management
Features
OkiNet Alert
OKI OkiNet Alert enterprise management utility allows
administrators to proactively manage printers by being
immediately alerted to printing problems before they
are encountered by users. This remote management
utility can be configured to monitor all SNMP traps
from a list of printers chosen by the administrator,
without requiring HP OpenView. It runs in the
background on any Windows-based PC and alerts the
user with a sound or a screen flash when an error has
occurred, and OkiNet Alert can be configured to
respond only to the specific error conditions that are of
concern to you. You can also launch batch files on
given error conditions. OKI OkiNet Alert can be used
in IPX and IP environments. Additionally, multiple
traps can be sent to multiple destinations on the
network.
Enhanced Printer Status
The OkiLAN 6020e communicates with the printer to
monitor the current condition on the printer. This
information can be observed in real time via the utilities
or can be interpreted by the OkiLAN 6020e to generate
traps to your SNMP management utility of choice: HP
OpenView or the OKI OkiNet Alert utility.
For bi-directional capable printer the OkiLAN 6020e
can retrieve the printer information, such as front panel
message, and display it through the OkiNet utilities.
II - 18
OKI OkiLAN 6020e User’s Guide
Section 2 - Chapter 5 - Additional Management Features
OkiNet for NDS allows administrators to create and
manage OKI print server objects in the NDS tree.
OkiNet for NDS integrates into Novell’s NetWare
Administrator, NetWareAdmin. For more information,
see OkiNet for NDS under NetWare in this manual.
OkiNet for TCP/IP
(Creating Custom Views)
OkiNet for TCP/IP allows discovery on a pure
TCP/IP Windows environment. To assign a TCP/IP
address assignment, simply select Discover
Unconfigured Device and double-click. To create
multiple views and customize the viewing environment,
specify devices and define Filters, Sorts, Columns,
Search Information and Refresh rates. For more
information about OkiNet for TCP/IP, see Creating
Custom Views under the TCP/IP section of this manual.
NetWare Load Balancing
Using this feature, administrators can distribute the
print load among several print servers. Simply assign
the queue to the desired print ports on the selected print
servers.
Windows Printing
From a Windows operating system, using TCP/IP or
DLC protocols, the OkiNet Connect utility routes the
print job to the appropriate printer without passing
through a file server or print queue. This cuts down on
network printing traffic. For more information, see the
Windows Printing section of this manual.
Printer Security for TCP/IP Printing
The OkiLAN 6020e print server has a Printer Security
for TCP/IP Printing feature which allows the printers
to only be accessed from a specified list of IP
addresses. This feature is accessed via TELNET option
#9, TCP Connection Configuration.
OKI OkiLAN 6020e User’s Guide
II - 19
Advanced Management
OkiNet for NDS
Section 2 - Chapter 5 - Additional Management Features
II - 20
OKI OkiLAN 6020e User’s Guide
Section III:
NetWare
NetWare
Section 3 - NetWare
In This Section
Chapter 1 Introduction ...........................................III-4
Overview ...................................................... III-4
Before You Start ........................................... III-4
Selecting PServer or RPrinter/NPrinter
Mode ........................................................... III-5
Chapter 2 OkiNet for NetWare ...............................III-6
Overview ...................................................... III-6
Running OkiNet for NetWare ....................... III-7
Configuring the OkiLAN 6020e Using OkiNet
for NetWare ................................................ III-7
NetWare Configuration Options ................... III-8
NetWare Queues Configuration Options ...... III-9
NetWare Port Configuration Options ......... III-10
TCP/IP Configuration Options ................... III-10
EtherTalk Configuration Options ............... III-11
Output Port Configuration Options ............ III-11
SNMP Configuration Options .................... III-13
SNMP Traps Configuration ........................ III-15
Saving the Configuration ............................ III-16
Enabling/Disabling Protocols ..................... III-17
Displaying OkiLAN 6020e Diagnostic
Information ............................................... III-17
Printing a Configuration Sheet ................... III-17
Resetting the OkiLAN 6020e ..................... III-17
Restoring Factory Default Settings ............. III-18
Creating Customized Views ....................... III-19
Modifying View Settings ............................ III-20
Permanently Defining SNMP Access
Information ............................................... III-22
III - 2
OKI OkiLAN 6020e User’s Guide
Section 3 - NetWare
Chapter 3 OkiNet for NDS ....................................III-24
Chapter 4 Using the OkiLAN 6020e
in NDPS (NetWare 4.x and 5.1) ............................III-33
Introduction ................................................ III-33
Adding the Oki Printer Driver Using NDPS
Broker ....................................................... III-33
Setting Up the OkiLAN 6020e Through
NWAdmin32 ............................................ III-35
Setting Up the OkiLAN 6020e for
Public Access Printers
At the File Server Console ....................... III-37
OKI OkiLAN 6020e User’s Guide
III - 3
NetWare
Overview .................................................... III-24
Installing OkiNet for NDS for Novell
NetWare 4.1 .............................................. III-25
Installing OkiNet for NDS for Novell
NetWare 4.x, NetWare 5.x,
and Windows 3.x ...................................... III-26
Installing OkiNet for NDS for Novell
NetWare 4.x, NetWare 5.x, Windows 95/98
and Windows NT/2000 ............................ III-27
Creating a New OkiLAN 6020e Object ..... III-28
Printing with an OkiLAN 6020e Print
Server ....................................................... III-29
Configuring the OkiLAN 6020e Using
OkiNet for NDS ....................................... III-31
Adding or Removing the OKI Print
Server Class .............................................. III-31
Section 3 - Chapter 1 - Introduction
Chapter 1: Introduction
Overview
This section contains instructions and information on
how to configure your OkiLAN 6020e in the NetWare
environment.
There are three environments in which to configure the
OkiLAN 6020e:
• Bindery (NetWare 3.x)
• NetWare Directory Services (NDS)-for NetWare
versions 4.1 and later
• NDPS for NetWare 4.x and 5.x.
Before You Start
• You should be familiar with network administration
as well as the physical setup and operation of your
network.
• Write down the serial number and the Ethernet or
Token-Ring address of your OkiLAN 6020e. You
will find these numbers on the OkiLAN 6020e
enclosure.
• Install the OkiLAN 6020e hardware and connect the
cabling-see Section I. Instructions for hardware
installation are found in Section I of this manual.
• Install the OkiNet Utility for NetWare--see Section I.
III - 4
OKI OkiLAN 6020e User’s Guide
Section 3 - Chapter 1 - Introduction
Selecting PServer or
RPrinter/NPrinter Mode
Your OkiLAN 6020e supports both PServer and
NPrinter mode. There are several factors to consider
when choosing which mode to use.
In PServer mode, the OkiLAN 6020e operates as the
print server. It services specified queues on the
network. In RPrinter mode, the NetWare Print Server
NLM or EXE is in control.
PServer Mode
RPrinter/NPrinter Mode
User
Connection
Requires one NetWare
user connection per
OkiLAN 6020e.
Requires no user
connection.
Performance
High performance.
Good performance.
Installation
Easier to set up.
Requires fewer steps.
More steps to set up, but
works well with existing
utilities.
Print Server
Separate print server
node, print server
functions, and NetWare
print server software
not required.
Requires NetWare print
server software. Integrates
with NetWare print utilities.
Status
Reporting
Printer status is
reported via messages
sent to client nodes. Job
status is available via
job notification. Printer
status available via
OkiNet utilities.
Printer status is reported via
PCONSOLE, PSC, and
print server screen. Job
status is reported via the
print server screen, PSC,
job notification.
Security
Without supervisor
intervention, other
printers cannot access
data sent to the queues.
Data can be password
protected from the file
server to the printer.
Data can be password
protected from the file
server to the printer.
OKI OkiLAN 6020e User’s Guide
III - 5
NetWare
Feature
Section 3 - Chapter 2 - OkiNet for NetWare
Chapter 2
OkiNet for NetWare
Overview
This chapter contains information about how to
configure the OkiLAN 6020e in Bindery and NDS
environments using the OkiNet for NetWare utility.
Note: OkiNet for NetWare contains minimal NDS
configuration support. For more extensive
configuration options, use the OkiNet for NDS
utility described in Chapter 3.
OkiNet for NetWare allows you to:
• Configure the OkiLAN 6020e for all Supported
Protocols
• Display OkiLAN 6020e Diagnostic Information
• Print a Configuration Sheet
• Reset the OkiLAN 6020e
• Restore Factory Default Settings
• Create Customized Views
• Modify View Settings
• Permanently Define SNMP Access Information
III - 6
OKI OkiLAN 6020e User’s Guide
Section 3 - Chapter 2 - OkiNet for NetWare
Running OkiNet for NetWare
To run the utility, double-click on the OkiNet icon. The
main OkiNet for NetWare screen will display.
Configuring the OkiLAN 6020e Using
OkiNet for NetWare
The following steps outline how to configure an
OkiLAN 6020e.
1. Select the OkiLAN 6020e you wish to configure.
2. Select Configuration from the Print Server menu or
select the Configuration icon on the toolbar.
3. Set the appropriate configuration by choosing the
applicable file folder tabs.
The following settings are configurable based on the
capabilities of the OkiLAN 6020e:
• NetWare
• Output Port
• NetWare Queues
• SNMP
• NetWare Port
• VINES *
• TCP/IP
• EtherTalk
• Protocols
• SNMP Traps
* May apply to other OkiLAN print server models.
OKI OkiLAN 6020e User’s Guide
III - 7
NetWare
By default, the All Print Servers view is selected and all
print servers attached to the network from which the
OkiNet utility is running are listed.
Section 3 - Chapter 2 - OkiNet for NetWare
NetWare Configuration Options
To configure options specific to the NetWare protocol,
select the NetWare file tab. The following screen will
display:
PServer or RPrinter Mode
Several factors should be considered when choosing
between PServer or RPrinter mode. For more detailed
information regarding these modes, see page III-5.
Bindery Settings
• Default File Server - The default file server can be
selected from any file server listed in the Default
File Server scroll menu. The default file server must
be active at power up for the OkiLAN 6020e to
recognize other servers.
• Print Server Name - Enter the print server name of
your choice.
III - 8
OKI OkiLAN 6020e User’s Guide
Section 3 - Chapter 2 - OkiNet for NetWare
NDS settings need to first be created and setup using
the NWAdmin or PConsole utility. Create an NDS print
server object. Then, create one NDS printer object per
output port. For example, Printer 1 goes to Port 1,
Printer 2 goes to port 2. Attach NDS print queues to the
NDS printer objects. Once you have created NDS
objects and queues, use the OkiNet for NetWare utility
to configure the following fields:
• Preferred File Server - This is the file server on
which the print server object was created.
• Preferred Tree - This is the NDS tree on which the
NDS print server object was created.
• Print Server Name - The fully qualified (canonical)
name of the NDS print server object that was
created. The Print Server Name is case sensitive.
Example:
cn=marketinglj.ou=marketing.o=companyname
where cn is the Common Name of the leaf object, ou is
the Organizational Unit name, and o is the
Organizational name.
Note: After any change to the servicing of queues for
the OkiLAN 6020e from NWAdmin or
PConsole, the OkiLAN 6020e must be reset via
OkiNet for NetWare.
NetWare Queues Configuration
Options
The NetWare Queues option allows you to add bindery
print queues to be serviced by first selecting each
desired queue and then selecting the →button.
To have a queue print to an output port other than the
currently selected port, select the Output Port button
and then select the desired port.
OKI OkiLAN 6020e User’s Guide
III - 9
NetWare
NDS Settings
Section 3 - Chapter 2 - OkiNet for NetWare
NetWare Queue Load Balancing
Print jobs can be distributed to multiple printers on
selected queues by selecting the same queue multiple
times and selecting a different output port for each
queue entry.
NetWare Port Configuration Options
To modify the NetWare port settings to fit your
NetWare printing environment, select the NetWare
Port file tab.
TCP/IP Configuration Options
To modify configuration settings specific to the TCP/IP
protocol such as IP address, subnet mask and default
gateway. For specific information on TCP/IP
configuration options, see Section IV,
TCP/IP, or select the HELP button on the bottom right
of the screen.
III - 10
OKI OkiLAN 6020e User’s Guide
Section 3 - Chapter 2 - OkiNet for NetWare
EtherTalk Configuration Options
To modify configuration settings specific to the
EtherTalk protocol such as the name and zone. For
specific information on other EtherTalk options, see
Section VII, EtherTalk, or select the HELP button on
the bottom right of the screen.
Output Port Configuration Options
NetWare
To configure the OkiLAN 6020e output port, select the
Output Port file tab. The following screen will
display:
Port Number
Select the port you wish to configure.
Name Field
Enter a descriptive name to identify the port.
Language Switching
Each output port can be configured to perform the
following language switching options: OFF, PCL,
PostScript or Automatic. Unless OFF is selected, a
language switching character string will be inserted
before each print job. The Printer Type selection is
used to determine the actual characters required to
switch the language of the printer.
• OFF - Print data stream will be sent directly to the
output port without alteration.
• PCL - Inserts the appropriate character string in
front of each print job to switch the printer to the
PCL print language.
OKI OkiLAN 6020e User’s Guide
III - 11
Section 3 - Chapter 2 - OkiNet for NetWare
• PostScript - Inserts the appropriate character string
in front of each print job to switch the printer to the
PostScript printer language.
• Automatic - Enables the auto language sensing
function. This function examines the print job data
stream and determines the required print language
and inserts the appropriate character string in front
of each print job to switch the printer to the
appropriate printer language.
Note: If you are not switching languages or the
printer can switch languages automatically, this
option should be set to OFF.
Printer Type
The Printer Type selection is used to determine the
actual character string required for your printer. If your
printer type is not listed, select Other and enter the
character string for switching the printer to PCL or
PostScript mode.
To enter nonprintable characters, enclose the ASCII
value of the character in angle brackets. For example,
to enter the ESC character type: <27>.
PCL Switch Sequence
Enter the character string to switch the printer to the
PCL print language.
PostScript Switch Sequence
Enter the character string to switch the printer to the
PostScript print language.
Configuration Page Language
Select the appropriate printer language for printing
configuration pages on your printer.
Note: Do not set the Configuration Page Language to
OFF for all ports of your OkiLAN 6020e. If a
configuration sheet cannot be printed,
troubleshooting abilities are limited.
III - 12
OKI OkiLAN 6020e User’s Guide
Section 3 - Chapter 2 - OkiNet for NetWare
Bidirectional Printer Status Support
Enable this option for enhanced status from
bi-directional printers that support PJL.
Output Type
Select the desired level of support for 1284
communications. The following settings are available:
- Compatibility (no bidi)
- 1284 (Std Nibble Mode) (default)
- 1284 (ECP or Fast Nibble Mode)
SNMP options specify which information is necessary
for an SNMP manager to access the OkiLAN 6020e.
The system variables are for user convenience and are
optional.
SNMP community names are used as passwords to
GET and SET information on the OkiLAN 6020e. The
values should be changed for enhanced security.
To configure SNMP specific information, select the
SNMP file tab. The following screen will display:
Note: SNMP options need to be configured only if
you are managing OkiLAN 6020e products or
getting system information using SNMP.
OKI OkiLAN 6020e User’s Guide
III - 13
NetWare
SNMP Configuration Options
Section 3 - Chapter 2 - OkiNet for NetWare
Fill in the following information:
System Name
Enter the name of your choice. This name will identify
the OkiLAN 6020e in your SNMP-based management
program.
System Contact
Enter any information useful to a user if problems with
the OkiLAN 6020e arise.
System Location
Enter a description of the OkiLAN 6020e location.
Get Community Name
This field is used to set the community name required
to Get information from the print server. The default
community name is public.
Note: To use the JetAdmin utility with the OkiLAN
6020e, the Get and Set Community Names
must be set to public.
Set Community Name
This field sets the community name required to Set
information on the OkiLAN 6020e. The default
community name is public.
Note: The OkiLAN 6020e cannot be configured
without the correct Set community name. To
secure the configuration of the OkiLAN 6020e,
change the community name from the default
setting.
III - 14
OKI OkiLAN 6020e User’s Guide
Section 3 - Chapter 2 - OkiNet for NetWare
Trap Community Name
Enter the community name which will be used when
traps are sent from the OkiLAN 6020e. This setting
allows trap utilities to only accept traps from devices
with appropriate community names.
The Trap community name field is used by the OKI
OkiNet Alert and other monitoring utilities for grouping
or filtering OkiLAN 6020e devices. OkiNet Alert
assists in managing network printers by immediately
alerting you of printer problems.
The SNMP Trap option allows configuration of traps.
Traps are unsolicited information concerning the
OkiLAN 6020e. Traps can be sent to an SNMP
manager or be broadcast to all hosts on the local
segment.
To configure SNMP traps, select the SNMP Traps file
tab. The following screen will display:
Fill in the following information:
Protocol
Select the protocol for which you wish to configure
trap information.
OKI OkiLAN 6020e User’s Guide
III - 15
NetWare
SNMP Traps Configuration
Section 3 - Chapter 2 - OkiNet for NetWare
Trap Destination
• NetWare Protocol - Enter the network number and
hardware address, respectively, to which traps will
be sent. To broadcast traps to all addresses on all
networks, enter FFFFFFFF (8 characters) in the first
field and FFFFFFFFFFFF (12 characters) in the
second field. To broadcast traps to all addresses on a
specific network, enter the network number in the
first field and then FFFFFFFFFFFF (12 characters)
in the second field.
• TCP/IP Protocol - Enter the IP address to which
traps will be sent. The IP address must follow the
format XXX.XXX.XXX.XXX, where each XXX is
a number from 0 to 255. To broadcast traps to all
hosts on the local subnet, enter 255.255.255.255.
Ports to Trap
Select the output ports on which you wish traps to be
active.
Printer Traps
Select the printer traps to be activated. The following
printer conditions may cause a printer trap to occur if
the OKI printer model supports the features:
• On-line
• Off-line
• No Printer Attached
• Paper Out
• Toner Low
• Paper Jam
• Door Open
• Printer Error
Note: Toner Low, Paper Jam and Door Open require
the printer to be set in PCL or Auto mode.
Saving the Configuration
Once all settings have been defined, select OK. The
settings will be saved and you will be returned to the
main OkiNet for NetWare screen.
III - 16
OKI OkiLAN 6020e User’s Guide
Section 3 - Chapter 2 - OkiNet for NetWare
Enabling/Disabling Protocols
To enable or disable protocols on the OkiLAN 6020e,
select the Protocols file tab. Select each protocol you
wish to enable. If you disable a protocol, the OkiLAN
6020e will no longer communicate using that protocol.
To reduce unnecessary network traffic, disable unused
protocols.
To view OkiLAN 6020e diagnostic information, select
Diagnostics from the Print Server pull-down menu on
the main NetWare Print Manager screen. Diagnostic
information is available for the following topics:
• Printer
• Print Server
• Protocols
• Network
• Statistics
• Technical Support
• System
Printing a Configuration Sheet
The configuration sheet provides current network, print
server and printer information. To print a configuration
sheet, select the OkiLAN 6020e from the list of
available print servers. Select Print Configuration
Sheet from the Print Server menu bar.
Resetting the OkiLAN 6020e
To reset the OkiLAN 6020e, select the OkiLAN 6020e
from the list of available print servers. From the Print
Server menu bar, select Reset.
OKI OkiLAN 6020e User’s Guide
III - 17
NetWare
Displaying OkiLAN 6020e Diagnostic
Information
Section 3 - Chapter 2 - OkiNet for NetWare
CAUTION: Make sure there are no print jobs active
when you reset the OkiLAN 6020e. All protocols will
be restarted. If you attempt a reset while a job is
printing, the job may not print successfully.
Restoring Factory Default Settings
To restore the OkiLAN 6020e to factory default
settings, select the OkiLAN 6020e from the list of
available print servers. From the Print Server menu bar,
select the Reset option. Choose one or more of the
following options:
Output Ports
Restores settings related to output ports such as port
name and output type.
TCP/IP
Restores settings specific to the TCP/IP protocol
configuration such as the IP address and subnet mask.
NetWare
Restores settings specific to the NetWare protocol
configuration such as the mode and default file server.
EtherTalk
Restores settings specific to the EtherTalk protocol
configuration such as the name and zone.
Once you have chosen the desired options, select
Restore. To completely restore the print server to
factory default settings, select all items in the list.
III - 18
OKI OkiLAN 6020e User’s Guide
Section 3 - Chapter 2 - OkiNet for NetWare
CAUTION: Make sure there are no active print jobs
when you select Restore Factory Defaults. If you reset
the OkiLAN 6020e while a job is printing, the job may
not print successfully.
OkiNet for NetWare allows users to create multiple
customized views for the list of OkiLAN 6020e
products. By creating different views, the user can
narrow the information displayed to that which is of
highest priority. These views can be saved and selected
as needed.
OkiNet has two predefined views. The All Print Servers
view displays all the print servers available on your
local network. The Unconfigured Print Servers View
displays only the print servers on the local network that
have not been configured.
Creating a New Customized View
To create a new view, select the New option from the
View menu. Enter a name for the new customized view.
Define Filters, Sorts, Column, Search information and
Refresh rates (see the Modifying View Settings sections
for more detail). Select OK to save this view.
Selecting an Existing View
To select an existing view, choose Select from the View
menu. Highlight the view you wish to open and select
OK. The OkiLAN 6020e list in the utility will be
displayed as described by the view selected.
Searching for a Specific OkiLAN 6020e
To search for a specific OkiLAN 6020e, select Search
from the tools menu. Choose the Search List option to
search for OkiLAN 6020e products already listed. For
OkiLAN 6020e products which cannot be found in the
list, select the Search Network by Address option. For
more information about this option, select HELP.
OKI OkiLAN 6020e User’s Guide
III - 19
NetWare
Creating Customized Views
Section 3 - Chapter 2 - OkiNet for NetWare
Modifying View Settings
Before modifying the settings, select the name of the
view you wish to edit from the Name field.
Display Filter
The filter option displays only those print servers
matching specific criteria. The print server list can be
filtered by any of the following:
Filter By
Enter for the Filter Value
<No Filter>
No value
DateCode
Four digits followed by a letter (e.g. 9502B)
H/W Address
12 hexadecimal digits for the hardware
address
Name
NetWare print server name
Product #
Select from the list of product number(s)
Product Type
Select from the list of product types
Status
Select from the list of status conditions
Default File Server
The default NetWare file server
Mode
running
The NetWare mode the print server is
Network #
The IPX network number
Search Filter
The Search option defines the criteria for locating
OkiLAN 6020e products on the network.
• Search Local Network - This method searches the
bindery to locate all OkiLAN 6020e products on the
network. All OkiLAN 6020e print servers that
respond are placed in the list. If you have a large
number of OkiLAN 6020e print servers on your
network and do not wish to view all of them, do not
select this option.
III - 20
OKI OkiLAN 6020e User’s Guide
Section 3 - Chapter 2 - OkiNet for NetWare
• Specify Devices/Networks - This method adds
specific print servers (or groups of print servers) to
the list. This can be useful when only a subset of the
list of OkiLAN 6020e products is desired.
To select all desired print servers, select Add.
Sort
The Sort option displays the OkiLAN 6020e list in a
specific order. The list can also be sorted by clicking on
the column by which you wish to sort. A sort order can
only be defined on columns displayed on the main
OkiNet for NetWare screen.
Column information for each print server can be
modified. To define the location of a new column,
select the location in the Columns Displayed field
where you wish the new column to be inserted, then
select Add. If no location is selected, the new column
will be added to the end of the list and the column will
be displayed to the right of the last column on the
screen. For example, if you currently have three
columns displayed and you wish to add a fourth
column to the far left of the screen, follow these steps:
1. Select the first column in the Columns Displayed
field.
2. Select the column to be added from the Columns
Available field.
3. Select Add.
Columns may also be removed by selecting Remove
from the Columns Available field.
OKI OkiLAN 6020e User’s Guide
III - 21
NetWare
Columns
Section 3 - Chapter 2 - OkiNet for NetWare
Refresh
The refresh rate defines how often the OkiNet for
NetWare utility updates the main print server list. To
define a refresh rate, select the Automatic Refresh box
and then enter the refresh rate in the field provided.
Decide how frequently to refresh the screen based on
factors such as network traffic and desire for most
recent information. For example, if traffic is not an
issue on your network and the most current information
is desired, set the refresh rate to 1 so the screen is
updated every minute. If network traffic is an issue,
you may wish to set the refresh rate to 10. This would
update the screen every ten minutes and minimize
network traffic.
Permanently Defining SNMP Access
Information
Access to OkiLAN 6020e configuration and diagnostic
information is determined by using community names.
The Special Options window is used to permanently
define access information so it does not need to be
entered each time the OkiLAN 6020e is accessed. To
Get and/or Set information on the OkiLAN 6020e
through OkiNet for NetWare, community names used
by the utility must match the community names
assigned to the OkiLAN 6020e.
To configure the OkiNet for NetWare utility to use the
correct community names, select Special Options from
the File menu.
Serial/Network Numbers
This field displays the serial number of each OkiLAN
6020e or the network number for a network of OkiLAN
6020e products for which the OkiNet utility has defined
access. To add a new serial number or network number
to this list, select the Add button.
Get Community Name
Enter the Get Community Name necessary to access
the OkiLAN 6020e or group of OkiLAN 6020e
products selected.
III - 22
OKI OkiLAN 6020e User’s Guide
Section 3 - Chapter 2 - OkiNet for NetWare
Set Community Name
Enter the Set Community Name necessary to access the
OkiLAN 6020e or group of OkiLAN 6020e products
selected.
Add
Select the Add button to define access to a new
OkiLAN 6020e or a group of OkiLAN 6020e products.
Enter a serial number or a network number followed by
a dash (-). Use an asterisk (*) as a wildcard to match
multiple devices. As examples, to add a single OkiLAN
6020e, enter 1500001, or to add a whole network, enter
D4-.
Delete
NetWare
The Delete button deletes an OkiLAN 6020e access
entry in the Serial/Network Number list.
OKI OkiLAN 6020e User’s Guide
III - 23
Section 3 - Chapter 3 - OkiNet for NDS
Chapter 3
OkiNet for NDS
Overview
OkiNet for NDS is a Dynamic Link Library (DLL)
which allows users to create and manage OKI print
server objects in the NDS tree. OkiNet for NDS
integrates into Novell’s NetWare Administrator, a
Windows-based utility that allows users to view and
manage their NetWare 4.x NDS tree. Once OkiNet for
NDS is integrated into NetWare Administrator, users
can manage OKI devices with the same utility used to
manage other network objects such as printers and
queues.
The OkiLAN 6020e supports NetWare NDS using
Novell Embedded Systems Technology, also known as
NEST.
OkiNet for NDS can be installed to support Novell
NetWare version 4.1 or 4.11 and for operating systems
running Windows 3.x, Windows 95/98, and Windows
NT/2000. If you have multiple versions of Windows
operating systems to service, you can install OkiNet for
NDS for each.
OkiNet for NDS supports four different versions of
NWAdmin.
• OkiNet for NDS installation for NetWare version 4.1
(one version of NWAdmin) requires a single
installation which will work for all platforms
including Windows 3.x. Windows 95/98, and
Windows NT/2000.
• The OkiNet for NDS installation for NetWare
version 4.11 requires a separate installation for each
of the three platforms: Windows 3.x, Windows 95/
98, and Windows NT/2000 (three separate versions
of NWAdmin).
III - 24
OKI OkiLAN 6020e User’s Guide
Section 3 - Chapter 3 - OkiNet for NDS
Refer to the following table to determine which method
to use to install OkiNet for NDS:
Client Operating System
NetWare
Version
Windows 3.x
Windows 95/98
Windows NT/2000
NetWare 4.1
See Installing OkiNet for NDS for Novell
NetWare 4.1
NetWare 4.11
and NetWare 5
See Installing
OkiNet for NDS
for Novell NetWare
4.11 and Windows
3.x
See Installing OkiNet
for NDS for Novell
NetWare 4.11 and
Windows 95/98 and
Windows NT/2000
A single installation is required to service
Windows 3.x and Windows 95/98 operating
systems with OkiNet for NDS for Novell NetWare
4.1. OkiNet for NDS must be installed in the same
location you have installed NetWare
Administrator. This may be located on the file
server or on an independent workstation. In most
cases NetWare Administrator can be found in the
SYS:\PUBLIC directory. To install OkiNet for
NDS for Novell NetWare 4.1 and Windows 3.x
and/or Windows 95/98:
1. Login to the directory tree as a user with
Admin rights at the root of the directory tree.
2. Run the installation program provided. Select
the option to install OkiNet for NDS. Follow
the instructions on the screen.
Tip for Advanced Administrators
When installing OkiNet for NDS, the install
utility copies the OkiNet for NDS files to the
destination directory, adds the OKI print
server class to the NDS schema and modifies
the user’s NWADMIN.INI file.
OKI OkiLAN 6020e User’s Guide
III - 25
NetWare
Installing OkiNet for NDS for
Novell NetWare 4.1
Section 3 - Chapter 3 - OkiNet for NDS
Installing OkiNet for NDS for Novell
NetWare 4.x, NetWare 5.x, and
Windows 3.x
OkiNet for NDS must be installed in the same location
you have installed NetWare Administrator. This may be
located on the file server or on an independent
workstation. In most cases NetWare Administrator can
be found in the SYS:\PUBLIC directory. To install
OkiNet for NDS for Novell NetWare version 4.11 and
Windows 3.x:
1. Login to the directory tree as a user with Admin
rights at the root of the directory tree.
2. Install OkiNet for NDS.-see Section I.
Tip for Advanced Administrators
When installing OkiNet for NDS, the install utility
copies the OkiNet for NDS files to the destination
directory, adds the OKI print server class to the
NDS schema and modifies the user’s
NWADMIN3X.INI file.
III - 26
OKI OkiLAN 6020e User’s Guide
Section 3 - Chapter 3 - OkiNet for NDS
OkiNet for NDS must be installed in the same location
you have installed NetWare Administrator. This may be
located on the file server or on an independent
workstation. In most cases NetWare Administrator can
be found in the SYS:\PUBLIC\Win95 or
SYS:\PUBLIC\WinNT directory. To install OkiNet for
NDS for Novell NetWare version 4.11 and Windows
95/98 and Windows NT/2000:
1. Login to the directory tree as a user with Admin
rights at the root of the directory tree.
2. Install--see Section I.
Tip for Advanced Administrators
When installing OkiNet for NDS, the install utility
copies the OkiNet for NDS files to the destination
directory, adds the OKI print server class to the
NDS schema and modifies the user’s registry.
OKI OkiLAN 6020e User’s Guide
III - 27
NetWare
Installing OkiNet for NDS for Novell
NetWare 4.x, NetWare 5.x,
Windows 95/98 and Windows NT/2000
Section 3 - Chapter 3 - OkiNet for NDS
Creating a New OkiLAN 6020e Object
To create a new OkiLAN 6020e object from Novell’s
NetWare Administrator, perform the following steps:
1. Select the container (also known as organizational
unit) in which you want the object created. For
example, to create an object that is within the sales
organizational unit, select SALES.
2. From the Object menu, select Create. If the Create
option is grayed, you do not have sufficient rights or
you have selected a leaf object.
3. From the Class of New Object list box, select OKI
Print Server. If the OKI Print Server is not listed,
check the following:
• The OkiNet for NDS utility has been installed.
• The OKI Printing Device has not been removed
from the schema. See Adding or Removing the
OKI Print Server section for more information.
4. Click OK.
5. Define filter and sort criteria for displaying a list of
Extended Systems devices from which to choose.
6. Click OK. The following screen will display:
III - 28
OKI OkiLAN 6020e User’s Guide
Section 3 - Chapter 3 - OkiNet for NDS
Note: If the Device list box is still empty, select Find
Device. This will allow you to locate the
specific device you are trying to define. You
will be prompted for the Ethernet address and
network number of the device. A mismatch in
the OKI device frame format may cause the
device not to show up in the Device list box.
Printing with an OkiLAN 6020e Print
Server
To configure the NetWare environment for printing to
an OkiLAN 6020e print server, follow these steps:
1. Install the OkiLAN 6020e hardware and connect the
cabling. Instructions for hardware installation are
found in Section I of this manual.
2. Create an OKI Print Server object. If you are
unfamiliar with how to do this, see the previous
section.
3. Open the OKI Print Server object’s Details dialog.
This may be done by double-clicking on the OKI
print server icon in the NDS tree or by selecting
Details from the File menu.
4. If your OkiLAN 6020e supports both PServer and
NPrinter mode, there are several factors to consider
when choosing which mode to use. See page III-5
for more information. From the Identification page,
select either PServer or NPrinter mode. If you select
NPrinter mode, skip to Step 11.
5. From the Assignments page, choose the Port #
associated with the printer to which the queue will
print.
OKI OkiLAN 6020e User’s Guide
III - 29
NetWare
7. From the list of OKI devices, select a device to
assign to the object.
8. Enter a name for the new OKI Print Server object.
9. Select Create.
The new OKI Print Server object should now appear in
the directory tree.
Section 3 - Chapter 3 - OkiNet for NDS
6. Select Assign.
7. Select or create a NetWare Printer object from the
Printer/Queue Assignments dialog.
8. Select or create a NetWare Print Queue object from
the Printer/Queue Assignments dialog.
9. Select OK to save your printer and queue selections.
Note: To load balance print queue jobs, repeat steps 5
through 9 for another port. Create a new printer
object for the OkiLAN 6020e port and then
select the same print queue object. This will
allow multiple printers to service a single print
queue.
10. From the Assignments page, select OK to save
changes. If you have selected PServer mode, you
have completed all necessary steps. Continue to
Configuring the OkiLAN 6020e Using OkiNet for
NDS.
11. Select or create a NetWare Print Server object
from the Assignments page.
12. Select a port to configure from the Assignments
page, then select Assign.
13. Select or create a NetWare Printer object from the
Printer/Queue Assignments dialog.
14. Select or create a NetWare Print Queue object
from the Printer/Queue Assignments dialog.
15. Select OK to save your printer and queue
selections.
16. From the Assignments page, select OK to save
changes.
17. From the file server, restart the PSERVER.nlm.
III - 30
OKI OkiLAN 6020e User’s Guide
Section 3 - Chapter 3 - OkiNet for NDS
Configuring the OkiLAN 6020e Using
OkiNet for NDS
Adding or Removing the OKI Print
Server Class
The OKI print server class is added to Novell’s
NetWare Administrator by the installation utility. This
class must exist in order to create an OKI Print Server
object for use in printing to the device.
Removing the OKI Print Server Class
1. Run Novell’s NetWare Administrator.
2. Verify all OKI print server objects have been
removed from the directory tree.
3. From the Tools menu, choose Remove OKI
Printing Device Class. The OKI print server class
will no longer show up in the Create New Object
dialog. If the Remove OKI Printing Device Class
option is grayed, the class has already been removed.
If the option does not exist, OkiNet for NDS is not
installed.
OKI OkiLAN 6020e User’s Guide
III - 31
NetWare
The following steps outline how to configure an
OkiLAN 6020e.
1. From the NWAdmin screen, select (double-click) the
OkiLAN 6020e you wish to configure.
2. Set the appropriate configuration by choosing the
applicable detail pages.
The following settings are configurable:
• Identification
• Network Protocols
• Assignments
• Port Configuration
• Network Configuration
• Status
For specific information about these detail pages, select
the HELP button.
Section 3 - Chapter 3 - OkiNet for NDS
The install utility on the installation diskette can also be
used to remove the OKI print server class. This utility
removes the class from Novell’s NetWare
Administrator and removes all the associated files that
were copied during the installation process.
Note: Be sure to remove all OKI Print Server objects
from the directory tree before uninstalling
OkiNet for NDS.
Adding the OKI Print Server Class
The OKI print server class is initially added to Novell’s
NetWare Administrator when the Install utility is run
from the diskette. If the OKI print server class has been
removed through Novell’s NetWare Administrator’s
Tools menu, you will need to add the class again.
From the Tools menu in Novell’s NetWare
Administrator, choose Define OKI Printing Device
Class. If this option is grayed, the class has already
been added. If the option does not exist, you will need
to run the install utility from the diskette to install
OkiNet for NDS.
The OKI print server class will now appear in the
Create New Object dialog.
III - 32
OKI OkiLAN 6020e User’s Guide
Section 3 - Chapter 4 - Using the OkiLAN 6020e in NDPS
Chapter 4
Using the OkiLAN 6020e in NDPS
(NetWare 4.x and 5.1)
Introduction
Adding the OKI Printer Driver Using the NDPS
Broker
Printer drivers cannot be installed to the Resource Management
Service from multiple floppy disks. If a printer driver is shipped on
more than one disk, copy the files to a directory on a hard drive or
network drive and install the driver from there. Any problems in
adding the driver should be addressed to the OKI Customer Service
Center.
1.
In NetWare Administrator, double-click the Broker object.
2.
Click the Resource Management Service (RMS) tab.
3.
Make sure the Resource Management Service is enabled.
4.
Click Add Resources to display the Manage Resources
dialog box.
5.
Select the icon for the type of printer driver that you want
to add under the Resource Types window.
A complete list of currently loaded printer drivers of that
type appears in the Current Resources window.
6.
To add a driver to the list, click Add to display the Add
Resources dialog box.
OKI OkiLAN 6020e User’s Guide
III - 33
NetWare
Novell Distributed Print Services (NDPS) is Novell’s new
printing architecture for use with NetWare versions 4.x and 5.1. To
use the OkiLAN 6020e in NDPS, you must add the OKI printer
driver(s) to the NDPS Broker.
Requirements:
• IP Address on the file server
• IP address on the print server (NetWare-only print servers will
not work)
• The client must also run the most current version of the
NetWare client to get the NDPS objects.
Note: The client printing to the printer does not need an IP address.
Section 3 - Chapter 4 - Using the OkiLAN 6020e in NDPS
7.
Click Browse to display the Select Printer Driver dialog
box. Locate the appropriate printer driver .INF file.
8.
Select the .INF file and click OK. The .INF file and path
is selected in the Resource location box. The printer
drivers are in the Resources To Be Added box.
Click OK on the Add Resources Window.
Click OK on the Manage Resources window.
Note: When the Manage Resources window re-appears,
the printer driver(s) have been added to the NDPS Broker.
Click Cancel on the NDPS Broker window to EXIT the
NDPS Broker.
9.
10.
11.
12.
III - 34
OKI OkiLAN 6020e User’s Guide
Section 3 - Chapter 4 - Using the OkiLAN 6020e in NDPS
Setting Up the OkiLAN 6020e Through
NWAdmin32
Setting Up the OkiLAN 6020e for Public Access Printers
1.
Create NDPS Manager.
2.
Double click NDPS Manager.
3.
Go to Printer Agent List
4.
Click New. Enter a name for the Agent.
5.
Select NDPS Manager Name.
6.
Select Novell Printer Gateway as the Gateway type and
click OK.
7.
Select NONE as your Printer Type, select Novell Port
Handler as the Port Handler Type and click OK.
8.
Select Remote (LPR on IP) and click Next.
9.
From the OkiLAN 6020e Configuration Sheet, get the
print server’s IP address and use it for the Host Address
Box of the Novell Gateway Utility. Then, enter the print
server’s IP address. Also from the Configuration sheet, get
the output port of the print server. Then, enter the output
port as the Printer Name. Click Finish.
10.
If the “Loading Printer Agent” screen stays on for more
than 60 seconds, click “Stop Waiting.”
11.
Ignore the error message, “The Printer Agent Just Created
Needs Attention.”
12.
Choose the printer drivers and click Continue.
13.
The Status should show Idle.
OKI OkiLAN 6020e User’s Guide
III - 35
NetWare
There are two types of printers available with NDPS. One is Public
Access, which anyone on the tree can get to. The other is Private
Access, which requires rights to the object. For Public Access
printers, the NDPS Printer can be created at the file server console
or through Novell’s NetWare Administrator (NWAdmin32). The
File Server Console approach offers less flexibility in
configuration. Both approaches are described in this and the
following subsection.
Section 3 - Chapter 4 - Using the OkiLAN 6020e in NDPS
Private Access Printers: these can only be created
through NWAdmin32
1.
Create NDPS Manager in NWAdmin32.
2.
Go to the Context in which the Private Printer is to reside.
3.
Select Create. The New Object screen appears.
4.
Click NDPS Printer, then click OK. Click the Define
Additional Properties box, and click Create.
5.
Give the Agent a name, assign it to a NDPS Manager (use
the gray browse button marked “…”), then choose Novell
Printer Gateway.
6.
Select NONE as your Printer Type, select Novell Port
Handler as the Port Handler Type and click OK.
7.
Select Remote (LPR on IP) and click Next.
8.
From the OkiLAN 6020e Configuration Sheet, get the
print server’s IP address and use it for the Host Address
Box of the Novell Gateway Utility. Then, enter the print
server’s IP address. Also from the Configuration sheet, get
the output port of the print server. Then, enter the output
port as the Printer Name. Click Finish.
9.
If the “Loading Printer Agent” screen stays on for more
than a minute, click “Stop Waiting.”
10.
Ignore the error message, “The Printer Agent Just Created
Needs Attention.”
11.
Choose the printer drivers and click Continue.
III - 36
OKI OkiLAN 6020e User’s Guide
Section 3 - Chapter 4 - Using the OkiLAN 6020e in NDPS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Create NDPS Manager in NWAdmin32.
Load the NDPS Manager on the file server.
Select Insert New Printer Agent.
Give the Agent a Name.
Go to Configuration Utilities.
Select Novell Printer Gateway.
Select Appropriate Printer.
Select Novell Port Handler.
Select Remote Printer: LPR/TCPIP.
From the OkiLAN 6020e Configuration Sheet, get the
print server’s IP address. Click <Enter> at IP Host, then
enter IP address of print server.
The LPR Printer Name is the output port of the print
server.
Click Accept and Exit, then use Escape key to save.
OKI OkiLAN 6020e User’s Guide
III - 37
NetWare
Setting Up the OkiLAN 6020e for Public Access
Printers At the File Server Console
Section 3 - Chapter 4 - Using the OkiLAN 6020e in NDPS
III - 38
OKI OkiLAN 6020e User’s Guide
Section IV:
TCP/IP
TCP/IP
Section 4 - TCP/IP
In This Section
Chapter 1Introduction ........................................... IV-5
Overview ................................................................................... IV-5
Software Requirements ............................................................. IV-5
Network Preparation .................................................................. IV-6
Before You Start ........................................................................ IV-6
Overview of TCP/IP Configuration ........................................... IV-6
Chapter 2 Configuring the OkiLAN 6020e ........... IV-7
Choosing an IP Address ............................................................. IV-7
Configuring the OkiLAN 6020e ............................................... IV-8
Assigning the IP Address ........................................................... IV-8
Other Utilities .......................................................................... IV-12
Verifying Access to the OkiLAN 6020e .................................. IV-13
Chapter 3 TCP/IP Configuration and Printing ... IV-14
Overview ................................................................................. IV-14
Configuring for TCP/IP Network Printing .............................. IV-15
Remote Print Queue Name ...................................................... IV-15
Configuring a BSD-Style Print Queue .................................... IV-17
Remote LPD Printing .............................................................. IV-18
FTP Printing ............................................................................ IV-19
Timeout Checking ................................................................... IV-21
Raw Port Printing .................................................................... IV-22
Chapter 4 OkiNet for TCP/IP ............................... IV-23
Overview ................................................................................. IV-23
System Requirements .............................................................. IV-23
Running OkiNet for TCP/IP .................................................... IV-24
Configuring the OkiLAN 6020e Using OkiNet for TCP/IP .... IV-24
Configuring TCP/IP Options ................................................... IV-25
EtherTalk Configuration Options ............................................ IV-28
Output Port Configuration Options ......................................... IV-28
SNMP Configuration Options ................................................. IV-30
Enabling/Disabling Protocols .................................................. IV-32
SNMP Trap Configuration ...................................................... IV-32
IV - 2
OKI OkiLAN 6020e User’s Guide
Section 4 - TCP/IP
Saving the Configuration ........................................................ IV-34
Displaying OkiLAN 6020e Diagnostic Information ............... IV-34
Printing a Configuration Sheet ................................................ IV-34
Resetting the OkiLAN 6020e .................................................. IV-34
Restoring Factory Default Settings ......................................... IV-35
Creating Customized Views .................................................... IV-36
Modifying View Settings ......................................................... IV-37
Permanently Defining SNMP Access Information .................. IV-39
Configuring the Discovery UDP Port Number ....................... IV-41
Starting a Telnet Session .......................................................... IV-41
Starting the BOOTP Server ..................................................... IV-41
Chapter 5 Web Configuration ............................ IV-42
Chapter 6 Telnet Configuration .......................... IV-43
Overview ................................................................................. IV-43
Running a Telnet Session ........................................................ IV-43
Appendix A Troubleshooting ............................. IV-49
Main Status Indicator .............................................................. IV-49
Restoring the OkiLAN 6020e to Factory Defaults .................. IV-49
Unable to Assign IP Address ................................................... IV-50
Hardware Error Messages ....................................................... IV-53
Printing a Configuration Page ................................................. IV-54
Unable to Print ......................................................................... IV-54
Overview ................................................................................. IV-56
Assigning the OkiLAN 6020e IP Address
with BOOTP ..................................................................... IV-57
Configuring the OkiLAN 6020e IP
Address with RARP ......................................................... IV-60
Configuring HP-UX v8.07 for Printing
with the OkiLAN 6020e ................................................... IV-63
Configuring HP-UX v9.xx for Printing
with the OkiLAN 6020e ................................................... IV-66
Configuring HP-UX v10.xx for Printing
with the OkiLAN 6020e ................................................... IV-69
OKI OkiLAN 6020e User’s Guide
IV - 3
TCP/IP
Appendix B Application Considerations ........... IV-56
Section 4 - TCP/IP
Configuring SCO UNIX for Printing
with the OkiLAN 6020e ................................................... IV-73
IBM’s AIX ver. 3.x for Printing
with the OkiLAN 6020e ................................................... IV-75
Configuring Solaris 2.x for Printing
with the OkiLAN 6020e ................................................... IV-77
Configuring Sun-OS v4.1.x or Ultrix v4.2 for Printing
with the OkiLAN 6020e ................................................... IV-79
Appendix C Internet Printing Protocol (IPP) ..... IV-81
IV - 4
OKI OkiLAN 6020e User’s Guide
Section 4 - Chapter 1 - Introduction
Chapter 1
Introduction
Overview
This section contains instructions and information on
how to configure your OkiLAN 6020e. You will also be
instructed on how to set up your host computers to print
to the OkiLAN 6020e using the TCP/IP protocol.
OkiLAN 6020e supports TCP/IP methods for printing:
• Remote Line Printer Daemon (LPD)
• File Transfer Protocol (FTP)
• Printing directly through a TCP port (Raw Port
Printing)
Additionally, if the DHCP protocol is enabled as a
default, the print server may be accessed through an
ordinary Internet Web browser, such as Netscape
Navigator, or by using TELNET. See Chapters 5 and 6
in this section.
The OkiLAN 6020e may be configured for TCP/IP
using the OkiNet for TCP/IP utility, or from a computer
supporting the OkiNet for NetWare utility, Banyan
VINES OkiNet for VINES utility (may apply to other
OkiLAN print server models), OR telnet and one of the
following:
• Manual arp table entry and ping
• Static route entry using route add command
• DHCP
• RARP
• BOOTP
OKI OkiLAN 6020e User’s Guide
IV - 5
TCP/IP
Software Requirements
Section 4 - Chapter 1 - Introduction
Network Preparation
• You should be familiar with network administration
as well as the physical setup and operation of your
network.
• Advise users of possible disruption during
installation.
• Make sure the serial number and Ethernet address of
your OkiLAN 6020e are available.
• Assign an IP address and a hostname (alias) to the
OkiLAN 6020e.
Use the network name service or the “/etc/hosts” file
to add the OkiLAN 6020e to the network.
Before You Start
Before running OkiNet for TCP/IP, you must do the
following:
• Install the OkiLAN 6020e hardware and connect the
cabling. Instructions for hardware installation are
found in Section I of this manual.
• Write down the serial number and Ethernet address
of your OkiLAN 6020e. (These numbers are located
on the OkiLAN 6020e unit.)
• Install OkiNet for TCP/IP-see Section I.
Overview of TCP/IP Configuration
•
•
•
•
IV - 6
Assign an IP address for the OkiLAN 6020e
Configure the OkiLAN 6020e network information
Configure hosts for printing to the OkiLAN 6020e
Test print (optional)
OKI OkiLAN 6020e User’s Guide
Section 4 - Chapter 2 - Configuring the OkiLAN 6020e
Chapter 2
Configuring the OkiLAN 6020e
Choosing an IP Address
Every TCP/IP network device is required to have a
unique IP address. The IP address can be permanently
stored using one of the following:
• OKI OkiNet management utilities for TCP/IP, Novell
NetWare or Banyan VINES (may apply to other
OkiLAN print server models)
• OkiLAN 6020e Configuration utility via telnet.
Using factory default settings, the OkiLAN 6020e first
attempts to determine its IP address (flashing rapid
green) using DHCP, RARP, BOOTP or Gleaning. If the
OkiLAN 6020e has not resolved its IP address after 2
minutes, it defaults to 198.102.102.254. (This IP
address should be used only temporarily for
configuration purposes.)
To choose an IP address:
1. Select an IP address and hostname for the OkiLAN
6020e.
Example: 192.168.42.50 OkiLAN 6020e_name
2. Add the name and IP address to the “/etc/hosts” file
of each host that will access the OkiLAN 6020e. Or,
if your network uses a name service, add the host
name and IP address to the name server.
Most TCP/IP networks use the Network Information
Service (NIS), Domain Name Service (DNS) or the “/
etc/hosts” database. See your network documentation
for instructions.
OKI OkiLAN 6020e User’s Guide
IV - 7
TCP/IP
Note: The OkiNet utilities are the easiest way to
assign an IP address.
Section 4 - Chapter 2 - Configuring the OkiLAN 6020e
Configuring the OkiLAN 6020e
There are four utilities available to configure the
OkiLAN 6020e for TCP/IP printing. You may use
whichever utility is best suited for your needs.
• OkiNet for TCP/IP - Windows TCP/IP print
manager utility. See Chapter 3 of this section for
more information.
• OkiLAN 6020e Configuration Utility - This utility is
accessed via telnet. See Chapter 6 of this section for
more information.
In order to configure the OkiLAN 6020e via telnet,
you must first assign an IP address to the OkiLAN
6020e and verify communication by pinging the
device.
• OkiNet for NetWare - This windows utility must be
run from a Novell NetWare client. See Section III of
this manual for specific information.
• OkiNet for VINES (VPMAN) Utility - This
Windows utility must be run from a Banyan VINES
client (may apply to other OkiLAN print server
models).
Assigning the IP Address
There are eight different methods for assigning an IP
address to the OkiLAN 6020e: Gleaning, Static Route
Entry, DHCP, RARP, BOOTP and using the OkiNet or
OkiNet for VINES utilities. Gleaning, Static Route
Entry and RARP require the OkiLAN 6020e and the
host to be on the same subnet. DHCP and BOOTP also
have this restriction unless the network routers are
configured to pass these requests. The OkiNet and
OkiNet for VINES utilities (may apply to other
OkiLAN print server models) do not have this
restriction.
IV - 8
OKI OkiLAN 6020e User’s Guide
Section 4 - Chapter 2 - Configuring the OkiLAN 6020e
If an IP address has not been permanently assigned
when the OkiLAN 6020e is powered on or reset, it will
look for a ping packet on the network. If the OkiLAN
6020e receives a ping packet within two minutes, it will
accept the IP address in the ping packet as its own
address.
To use Gleaning, you must have Windows 95/98,
Windows NT/2000, or super-user privileges on a UNIX
system.
1. Add an entry in the ARP table that assigns an IP
address to the hardware address of the OkiLAN
6020e. To do this, use the arp command.
arp -s <ip_address><hardware_address> temp
UNIX Example:
arp -s 192.168.42.24 00:02:16:00:00:01 temp
Windows 95/98, Windows NT/2000 Example:
arp -s 192.168.42.24 00-02-16-00-00-01
2. Start a continuous ping to the OkiLAN 6020e.
ping <ip_address>
Example: ping 192.168.42.24
On some systems, this may require an additional
parameter. Some implementations of ping only send
out one ping packet which could get lost in transit.
Check your system documentation for more
information.
3. Connect power to the OkiLAN 6020e.
The OkiLAN 6020e will glean its IP address from
the ping packet. This IP address will remain in effect
until the OkiLAN 6020e is powered off or reset.
Therefore, a permanent IP address should be
assigned by running the OkiNet for TCP/IP utility or
via telnet.
Note: Gleaning does not work with Windows NT
Workstation 3.5.
OKI OkiLAN 6020e User’s Guide
IV - 9
TCP/IP
Gleaning
Section 4 - Chapter 2 - Configuring the OkiLAN 6020e
DHCP
The Dynamic Host Configuration Protocol (DHCP)
provides a framework for passing configuration
information to hosts on a TCP/IP network in a client/
server fashion. DHCP is based on the Bootstrap
Protocol (BOOTP), adding the capability of automatic
allocation of reusable network addresses and additional
configuration options. DHCP uses the same packet
structure as BOOTP so current BOOTP relay agents
will also interact with DHCP messages.
DHCP offers dynamic IP address allocation. When a
client receives an IP address, it also receives a lease (an
amount of time the host may use the address). The
lease times vary from 1 hour to 100 years, or may be
infinite. When the lease expires, the host must stop
using the address. DHCP may also be used like
BOOTP, with a certain IP address always assigned to a
certain device. Depending on the server, both methods
may be used at the same time.
If the OkiLAN 6020e does not find a DHCP server
after two minutes, it will timeout and assume a default
address of 198.102.102.254. This follows current
BOOTP and RARP behavior.
If the OkiLAN 6020e receives multiple responses, it
will choose the first one.
When the OkiLAN 6020e receives an address, it sends
an ARP message once every second for five seconds on
the offered address to determine if another device is
using it. If the OkiLAN 6020e finds another device is
using the address, it will refuse the address and start
looking for a new address.
IV - 10
OKI OkiLAN 6020e User’s Guide
Section 4 - Chapter 2 - Configuring the OkiLAN 6020e
Static Route Entry
When the OkiLAN 6020e is powered on or reset and
no permanent IP address has been assigned, it will
attempt to obtain an IP address through Gleaning,
RARP, BOOTP or DHCP. If the OkiLAN 6020e has not
determined its IP address after two minutes, the IP
address will default to 198.102.102.254. This IP
address should only be used temporarily to configure a
new, permanent IP address. To change to a permanent
IP address, the route add command is used to place the
OkiLAN 6020e product’s default IP address into the
workstation’s network routing table. To use the route
command, you must have Windows 95/98, Windows
NT/2000 or super-user privileges under UNIX. The
syntax for this command is:
route add 198.102.102.254 “IP address of the
workstation” 0
The Static Route method only works if the host from
which you are telneting is on the same subnet as the
OkiLAN 6020e. Once the route add command has been
issued, telnet will allow you to change and/or make the
IP address permanent. After changing the IP address to
its permanent address, the routing table entry should be
deleted using route delete.
For more information, consult your system
documentation for the route command.
RARP or BOOTP
If an IP address has not been permanently assigned, the
OkiLAN 6020e will use Reverse Address Resolution
Protocol (RARP) or Bootstrap Protocol (BOOTP). The
OkiLAN 6020e will broadcast requests for its IP
address to both RARP and BOOTP servers. A RARP or
BOOTP server will respond by searching a
configuration file that maps the Ethernet hardware
addresses of devices on the network to their respective
IP addresses. If a match is found, the server’s response
will include the IP address of the device.
OKI OkiLAN 6020e User’s Guide
IV - 11
TCP/IP
Note: The zero (0) placed at the end of the route add
command shown above is optional.
Section 4 - Chapter 2 - Configuring the OkiLAN 6020e
Most UNIX operating systems support either the RARP
or BOOTP protocol. To find out which protocol your
operating system supports, request the manual page for
the protocol’s daemon (e.g. man bootpd or man rarpd),
or see your network manuals. Both protocols require
that you add the product’s network hardware address
and IP address to a configuration file. See your network
documentation for instructions or refer to Appendix B,
Application Considerations.
Note: An IP address received from a RARP or
BOOTP server is not permanently programmed
into the OkiLAN 6020e. Therefore, if you
choose this method of assigning the IP address,
the RARP or BOOTP server must be available
every time the OkiLAN 6020e is powered on
or reset. The IP address can be stored
permanently using telnet, OkiNet for TCP/IP,
OkiNet for NetWare or the OkiNet for VINES
utility (may apply to other OkiLAN print server
models).
A Winsock compliant BOOTP server is located on the
OkiNet for TCP/IP diskette. This has been provided for
users who do not have UNIX machines.
Other Utilities
The IP address can also be set from Novell NetWare
using the OkiNet for NetWare utility or through the
Banyan VINES OkiNet for VINES utility (may apply
to other OkiLAN print server models).
Note: The OkiNet for NetWare and OkiNet for
VINES utilities can only be used if Novell
NetWare or Banyan VINES are installed on
your network respectively (may apply to other
OkiLAN print server models).
IV - 12
OKI OkiLAN 6020e User’s Guide
Section 4 - Chapter 2 - Configuring the OkiLAN 6020e
Verifying Access to the OkiLAN 6020e
TCP/IP
Use the ping utility to verify access to the OkiLAN
6020e.
ping <IP address of OkiLAN 6020e>
If the OkiLAN 6020e does not respond, your network
or the device is not configured correctly.
• Verify the IP address, default gateway and subnet
mask are set to the proper values on the OkiLAN
6020e by printing a configuration sheet. This can be
done using either the print configuration sheet
button, through the OkiNet or OkiNet for VINES
utilities (may apply to other OkiLAN print server
models) or via telnet.
• If the settings appear to be correct, try repeating the
installation steps. If problems persist, call Oki Data
Customer Support at 1-800-OKI-DATA (1-800-6543282).
OKI OkiLAN 6020e User’s Guide
IV - 13
Section 4 - Chapter 3 - TCP/IP Configuration and Printing
Chapter 3
TCP/IP Configuration and
Printing
Overview
The OkiLAN 6020e supports printing from computers
using TCP/IP and any of the following printing
protocols:
• Line Printer Redirect/Line Printer Daemon (lpr/lpd)
• File Transfer Protocol (FTP)
• Printing directly through a TCP port (Raw Port
Printing)
This chapter presents basic instructions on how to
configure your computer to print using Remote LPD
and FTP. Specific instructions for several popular
computer systems have been documented in Appendix
B, Application Considerations. If your specific system
is not addressed in this appendix, follow the
instructions outlined below. You should also refer to
your operating system or computer manual for
information about configuring remote network printing.
If you are still unable to configure your computer
system to print to the OkiLAN 6020e, contact Oki Data
Customer Support at 1-800-OKI-DATA
(1-800-654-3282).
IV - 14
OKI OkiLAN 6020e User’s Guide
Section 4 - Chapter 3 - TCP/IP Configuration and Printing
Configuring for TCP/IP Network
Printing
Most computers that support TCP/IP network printing
use the Remote Line Printer Daemon (LPD) protocol.
This protocol was originally part of the Berkeley
Software Distribution (BSD) version of the UNIX
operating system. Remote LPD was quickly adopted as
a de facto standard. As a result, Remote LPD is now
supported by most versions of the UNIX operating
system and by many TCP/IP packages available for
other operating systems. Configuration of Remote LPD
printing varies among vendors who supply TCP/IP.
You may also use the File Transfer Protocol (FTP) for
printing. Typically FTP is used to transfer files between
computers on a TCP/IP network. The OkiLAN 6020e
simply prints the files it receives from FTP.
The Remote Print Queue Name determines which
printer port will service the print job. The Remote Print
Queue Name may also be used to specify ASCII print
jobs. Both Remote LPD and FTP have provisions for
specifying a Remote Print Queue Name.
The OkiLAN 6020e looks at the last character of the
Remote Print Queue Name to determine which printer
port will service the print job. All Remote Print Queue
Names should end with the number 1, 2, 3 or 4. If a
number is not specified, the OkiLAN 6020e will use
printer port 1.
The OkiLAN 6020e is designed to handle many
different types of printers and print data. Typically you
will select the printer type for your printer in telnet
under the Configure Port option. However, if you are
connecting to an ASCII printer, you may wish to use
the OkiLAN 6020e to format the print data for your
printer.
OKI OkiLAN 6020e User’s Guide
IV - 15
TCP/IP
Remote Print Queue Name
Section 4 - Chapter 3 - TCP/IP Configuration and Printing
The OkiLAN 6020e will parse the remote queue name
and search for certain characters at the end which tell
how to convert an ASCII print job. The print server
uses FF, LF and NF as ASCII conversion specifiers and
uses the last number as an output port. The FF, LF and
NF specifiers must be the last letters in the queue name.
Example: LaserWriterFF, SalesColorLaserNF,
ChemDeptLF2
FF
Use the FF suffix at the end of the Remote Print
Queue Name, before the port number.
Example: queueFF2
If the last character in the print job is not a form
feed, the OkiLAN 6020e appends a form feed.
This form feed prompts the printer to print any
partial page at the end of the job.
LF
Use the LF suffix at the end of the Remote Print
Queue Name, before the port number.
Example: queueLF2
In addition to the form feed described above,
the OkiLAN 6020e inserts a carriage-return
character into the print job immediately before
each line-feed character. This feature is useful
for printing UNIX text files.
NF
Use the NF suffix at the end of the Remote Print
Queue Name, before the port number.
Example: queueNF2
The OkiLAN 6020e inserts a carriage-return
character into the print job immediately before
each line-feed character. This feature is useful
for printing UNIX text files.
This option differs from LF in that form feed is
not added to the end of jobs.
IV - 16
OKI OkiLAN 6020e User’s Guide
Section 4 - Chapter 3 - TCP/IP Configuration and Printing
Configuring a BSD-Style Print Queue
For remote BSD-Style LPD printing, add the OkiLAN
6020e as a remote printer in the “/etc/printcap”
database to each host printing to the OkiLAN 6020e.
You can add PRINTCAP options as needed. If you are
unfamiliar with PRINTCAP, consult your local
documentation.
The entry should be similar to the following:
local_print_queue_name|[printer_model_and_
manufacturer]:\:lp=:mx#0:rm=OkiLAN
6020e_name:\:rp=remote_print_queue_name:\
:sd=path_to_spool_directory:lf=just
log_file_name
local_print_queue_name
The local_print_queue_name defines the name of the
printcap entry. It is used by the lpr/lpd utilities to
specify which printcap entry is being referenced.
Additional printcap entries can be added as needed for
different queue types. Each entry must have a unique
local_print_queue_name and a different spool directory
to work properly. When you are ready to print, use the
local_print_queue_name that matches the data type of
the file to be printed.
This is the name (alias) of the OkiLAN 6020e. This
must be the same name as entered in the /etc/hosts file
or your NIS or DNS system. An IP address may also be
used here.
remote_print_queue_name
The remote_print_queue_name entry determines the
OkiLAN 6020e port where the print job will be printed
and optionally specifies ASCII printing.
path_to_spool_directory
This is the path to a directory where the print jobs will
be spooled for this queue. You must create a unique
spool directory for each printcap entry.
OKI OkiLAN 6020e User’s Guide
IV - 17
TCP/IP
OkiLAN 6020e_name
Section 4 - Chapter 3 - TCP/IP Configuration and Printing
log_file_name
This is the path to a file where error information from
the lpd will be logged.
Example: If you are printing to an ASCII printer that
requires a carriage return/line feed, you may need two
separate printcap entries: one entry for print jobs which
terminate lines with a carriage return/line feed, and
another entry for print jobs which terminate lines with a
line feed only. Your printcap entries might look like the
following:
ascii_files|form.feed.Queue_on_Port_2:\
:lp=:mx#0:rm=pserver1:rp=MYQUEUEFF2:\
:sd=/usr/spool/myqueueff2:\
:lf=/usr/spool/myqueueff2/queue.log
asciilf_files|line.feed.Queue_on_Port_2:\
:lp=:mx#0:rm=pserver1:rp=MYQUEUELF2:\
:sd=/usr/spool/myqueuelf2:\
:lf=/usr/spool/myqueuelf2/queue.log
Note: Each printcap entry must have a different spool
directory to work properly.
Remote LPD Printing
The way print jobs are queued to a Remote LPD system
varies among the vendors that support TCP/IP. UNIX
systems that are BSD-based typically use the lpr
program to submit print jobs. Other UNIX systems may
use the lp program to submit print jobs. PC-based TCP/
IP packages often provide a command line lpr program
and a utility to redirect the output of an LPT port to a
Remote LPD system.
Consult your system administrator or software vendor
for assistance troubleshooting LPD.
IV - 18
OKI OkiLAN 6020e User’s Guide
Section 4 - Chapter 3 - TCP/IP Configuration and Printing
Note: The Remote LPD implementation of the
OkiLAN 6020e does not support any UNIX
LPD input or output filters or the direct
printing of banner pages. It is possible to
configure some UNIX systems so that banner
pages and input and output filters will be
generated at the UNIX host and then sent to the
OkiLAN 6020e. (Refer to Appendix B,
Application Considerations.)
FTP is a command line program used to transfer files
between computers. FTP provides commands for
opening a connection to another computer, specifying
the data type of any transfers, and sending and
receiving files. The OkiLAN 6020e supports a subset
of the FTP command set. This subset allows the FTP
user to open a connection to the OkiLAN 6020e,
specify a file transfer data type and send print files to a
Remote Print Queue Name on the OkiLAN 6020e.
The OkiLAN 6020e recognizes the following FTP
commands:
PUT
Print a single file
The PUT command sends the file to
the OkiLAN 6020e. The first
parameter of the PUT command is the
name of the local file to PUT. The
second parameter of the PUT
command is the name of the file for the
remote PC. In order to print the file,
this second parameter must be a
Remote Print Queue Name. If you do
not specify the second parameter, FTP
sets the remote file name to the local
file name. This may produce
undesirable printing results.
SEND
Treated the same as PUT.
MPUT
Print multiple files.
OKI OkiLAN 6020e User’s Guide
IV - 19
TCP/IP
FTP Printing
Section 4 - Chapter 3 - TCP/IP Configuration and Printing
TYPE
ASCII
BINARY
IMAGE
STRU
MODE
OPEN
CLOSE
QUIT
BYE
Changes the representation type used
for data transfer. Image (or binary) and
ASCII are the only types supported.
Equivalent to “TYPE ASCII.”
Equivalent to “TYPE BINARY.”
Equivalent to “TYPE IMAGE.”
Specifies file structure. File is the only
structure supported.
Specifies transfer mode. Stream is the
only transfer mode supported.
Opens connection to remote host.
Terminates FTP session.
Terminates FTP session and exits FTP.
Equivalent to QUIT.
With the exception of the OkiLAN 6020e 100 series,
OkiLAN 6020e print servers will allow one FTP
connection. If more FTP connections are attempted, the
OkiLAN 6020e will reject the connection until one of
the other FTP connections is closed. When an FTP
connection is rejected, the FTP program will typically
display a message like the following:
$ ftp<CR>
ftp> open OkiLAN 6020e_name<CR>
connection refused
ftp>
Note: Specifying binary mode is important for all
jobs. Most FTP implementations default to
ASCII mode. This may cause unexpected or
undesired printing results.
IV - 20
OKI OkiLAN 6020e User’s Guide
Section 4 - Chapter 3 - TCP/IP Configuration and Printing
Example: The following example prints a PostScript
file called chart.ps to the OkiLAN 6020e printer Port 1
using FTP.
$ ftp OkiLAN 6020e_name<Enter>
Connected to OkiLAN 6020e_name.
220 ESI-2810 Version 3.0 ready.
Name (OkiLAN 6020e_name:anyone):<Enter>
230 User logged in.
ftp> binary<Enter>
200 Type set to I.
ftp> put chart.ps MPX1<Enter>
local: chart.ps remote: MPX1
200 PORT command successful.
150 Opening BINARY mode data connection for
MPX1.
226 Transfer complete.
4549 bytes sent in 0 seconds (4.4 Kbytes/s)
ftp> bye<Enter>
221 Goodbye.<Enter>
$
If timeout checking is enabled on the OkiLAN 6020e,
the OkiLAN 6020e will close any connection that stays
idle for more than five minutes. For example, if you
open an FTP connection to the OkiLAN 6020e and
walk away from your computer for more than five
minutes, the FTP connection will be closed. You can
reestablish a connection to the OkiLAN 6020e with the
OPEN command.
OKI OkiLAN 6020e User’s Guide
IV - 21
TCP/IP
Timeout Checking
Section 4 - Chapter 3 - TCP/IP Configuration and Printing
Raw Port Printing
Host computer software can use a raw TCP/IP port
connection to send data to the OkiLAN 6020e. A TCP/
IP port has been assigned to the output port of the
OkiLAN 6020e as follows:
TCP/IP Port: 9100
Output Port: 1
Consult your system documentation for information on
how to submit print jobs to a raw port.
IV - 22
OKI OkiLAN 6020e User’s Guide
Section 4 - Chapter 4 - OkiNet for TCP/IP
Chapter 4
OkiNet for TCP/IP
Overview
This section contains information about OkiNet for
TCP/IP. OkiNet for TCP/IP provides SNMP-based
support for the entire OkiLAN 6020e family of print
servers.
OkiNet for TCP/IP allows you to:
• Easily assign an IP address
• Configure an OkiLAN 6020e for all Supported
Protocols
• Display OkiLAN 6020e Diagnostic Information
• Print a Configuration Sheet
• Reset the OkiLAN 6020e
• Restore Factory Default Settings
• Creating Customized Views
• Modify View Settings
• Permanently Define SNMP Access Information
OkiNet for TCP/IP is a Windows-based program which
is compatible with Windows 3.x, Windows NT/2000 and
Windows95/98.
OkiNet for TCP/IP requires that the TCP/IP protocol is
running using a Winsock (Windows Sockets) TCP/IP
stack, version 1.1 or greater. A Winsock TCP/IP
protocol stack is available from many vendors
including the following:
• Microsoft
• FTP Software
• Trumpet
• NetManage
• Distinct
For more information on the Winsock TCP/IP stack and
setting up a host name, see the README file.
OKI OkiLAN 6020e User’s Guide
IV - 23
TCP/IP
System Requirements
Section 4 - Chapter 4 - OkiNet for TCP/IP
Running OkiNet for TCP/IP
To run the utility, double-click on the OkiNet icon. The
main OkiNet for TCP/IP screen will display.
By default, the All Print Servers view is selected and all
print servers attached to the subnet of the network from
which the OkiNet utility is running are listed.
Configuring the OkiLAN 6020e Using
OkiNet for TCP/IP
The following steps outline how to configure an
OkiLAN 6020e. To change settings of a previously
configured OkiLAN 6020e, follow the same procedure
but skip Step 3, as no prompt will appear.
1. Select the OkiLAN 6020e you wish to configure.
2. Select Configuration from the Print Server menu or
select the Configuration icon on the toolbar.
3. When prompted, enter the IP Address of the
OkiLAN 6020e.
4. Set the appropriate configuration by choosing the
applicable file folder tabs.
The following settings are configurable:
• TCP/IP
• EtherTalk
• NetWare
• Output Port
• NetWare Port
• SNMP
• NetWare Queues • Protocols
• VINES*
• SNMP Traps
* May apply to other OkiLAN print server models.
IV - 24
OKI OkiLAN 6020e User’s Guide
Section 4 - Chapter 4 - OkiNet for TCP/IP
Configuring TCP/IP Options
To configure options specific to the TCP/IP protocol,
select the TCP/IP tab. The following screen will
display:
Fill in the following information:
• Set Permanent - Select this option to make the IP
address permanent. If the OkiLAN 6020e has been
configured to remember its IP address, it does not
need to determine its address each time it is powered
on.
Enter the IP address for the OkiLAN 6020e. The IP
address must follow the format
XXX.XXX.XXX.XXX, where each XXX is a
number from 0 to 255.
CAUTION: If you select an invalid IP address, you
may not be able to access the OkiLAN 6020e.
• Use Network Protocol - Select this option to use
RARP, BOOTP or DHCP to determine the IP address
at power up. Specify which protocol(s) to use.
OKI OkiLAN 6020e User’s Guide
IV - 25
TCP/IP
IP Address Resolution
Section 4 - Chapter 4 - OkiNet for TCP/IP
Subnet Mask
If your network environment includes subnets, you will
want to set the subnet mask. The subnet mask must
follow the format XXX.XXX.XXX.XXX, where each
XXX is a number from 0 to 255.
The default subnet mask is 0.0.0.0. The OkiLAN 6020e
interprets a subnet mask of 0.0.0.0 or 255.255.255.255
as no subnet mask specified.
CAUTION: If you select an invalid subnet mask, you
may not be able to access the OkiLAN 6020e.
Default Gateway
If your local network is attached to other networks, you
can specify the address of your default gateway. This
gateway will be selected whenever messages need to be
sent to another network.
The gateway address must follow the format
XXX.XXX.XXX.XXX, where each XXX is a number
from 0 to 255.
CAUTION: If you select an invalid default gateway or
the default gateway becomes unavailable, the OkiLAN
6020e may not be able to communicate with non-local
networks.
WINS Server
If you are using WINS name resolution, set the address
of the WINS Server where the System Name of the
OkiLAN 6020e will be registered.
Use DHCP to Locate WINS Server
If you are using DHCP for IP address resolution, select
this option to obtain the address of the WINS Server
from the DHCP Server.
IV - 26
OKI OkiLAN 6020e User’s Guide
Section 4 - Chapter 4 - OkiNet for TCP/IP
Telnet/HTTP Password:
Allows you to modify the current password required
for Telnet or HTTP access The default password is the
serial number of the OkiLAN 6020e.
NetWare and NetWare Port
Configuration Options
For specific information on NetWare or NetWare Port
options, see Section III, Novell NetWare, or select the
HELP button on the bottom right of the screen.
NetWare Queues Configuration
Options
The NetWare Queues option allows you to add bindery
print queues to be serviced by first selecting each
desired queue and then selecting the -> button.
To have a queue print to a specific output port, select
the Output Port button and then select the desired
port.
NetWare Queue Load Balancing
TCP/IP
Print jobs can be distributed to multiple printers on
selected queues by selecting the same queue multiple
times and selecting a different output port for each
queue entry.
OKI OkiLAN 6020e User’s Guide
IV - 27
Section 4 - Chapter 4 - OkiNet for TCP/IP
EtherTalk Configuration Options
To modify the configuration settings specific to the
EtherTalk protocol such as the name and zone. For
specific information on EtherTalk options, see Section
VI, EtherTalk, or select the HELP button on the
bottom right of the screen.
Output Port Configuration Options
To configure the OkiLAN 6020e output port, select the
Output Port file tab. The following screen will
display:
Port Number
Select the port number you wish to configure.
Name Field
Enter a descriptive name to identify the port.
Language Switching
Each output port can be configured to perform the
following language switching options: OFF, PCL,
PostScript or Automatic. Unless OFF is selected, a
language switching character string will be inserted
before each print job. The Printer Type selection is used
to determine the actual characters required to switch
your printer’s language.
IV - 28
OKI OkiLAN 6020e User’s Guide
Section 4 - Chapter 4 - OkiNet for TCP/IP
• OFF - Print data stream will be sent directly to the
output port without alteration.
• PCL - Inserts the appropriate character string in
front of each print job to switch the printer to the
PCL print language.
• PostScript - Inserts the appropriate character string
in front of each print job to switch the printer to the
PostScript printer language.
• Automatic - Enables the auto language sensing
function. This function examines the print job data
stream and determines the required print language
and inserts the appropriate character string in front
of each print job to switch the printer to the
appropriate printer language.
Note: If you are not switching languages or the
printer can switch automatically, this option
should be set to OFF.
Printer Type
PCL Switch Sequence
Enter the character string to switch the printer to the
PCL print language.
PostScript Switch Sequence
Enter the character string to switch the printer to the
PostScripti print language.
Configuration Page Language
Select the appropriate printer language for printing
configuration pages on your printer.
OKI OkiLAN 6020e User’s Guide
IV - 29
TCP/IP
The Printer Type selection is used to determine the
actual character string required for your printer. If your
printer type is not listed, select Other and enter the
character string for switching the printer to PCL or
PostScript mode.
To enter nonprintable characters, enclose the ASCII
value of the character in angle brackets. For example,
to enter the ESC character type: <27>.
Section 4 - Chapter 4 - OkiNet for TCP/IP
Output Type
Select the appropriate baud rate.
Bidirectional Printer Status Support
Enable this option for enhanced status from the
bidirectional printer.
SNMP Configuration Options
SNMP options specify which information is necessary
for an SNMP manger to access the OkiLAN 6020e. The
system variables are for user convenience and are
optional.
To configure SNMP specific information, select the
SNMP tab. The following screen will display:
Note: SNMP options need to be configured only if
you are managing an OkiLAN 6020e or getting
system information using SNMP.
Fill in the following information:
System Name
Enter the name of your choice. This name will identify
the OkiLAN 6020e in your SNMP-based management
program.
IV - 30
OKI OkiLAN 6020e User’s Guide
Section 4 - Chapter 4 - OkiNet for TCP/IP
System Contact
Enter any information useful to a user if problems with
the OkiLAN 6020e arise.
System Location
Enter a description of the OkiLAN 6020e location.
Get Community Name
This field is used to set the community name required
to Get information from the print server. The default
community name is public.
Note: For JetAdmin to function correctly with the
OkiLAN 6020e, the SNMP Get and Set
community name must be set to public.
Set Community Name
This field sets the community name required to Set
information on the OkiLAN 6020e. The default
community name is public.
Note: The OkiLAN 6020e cannot be configured
without the correct Set community name. To
secure the configuration of the OkiLAN 6020e,
change the community name from the default
setting.
Enter the community name which will be used when
traps are sent from the OkiLAN 6020e. This setting
allows trap utilities to only accept traps from devices
with appropriate community names.
The trap community name field is used by the OkiNet
Alert and other network monitoring utilities for
grouping or filtering OkiLAN 6020e devices. OkiNet
Alert assists in managing network printers by
immediately alerting you of printer problems.
OKI OkiLAN 6020e User’s Guide
IV - 31
TCP/IP
Trap Community Name
Section 4 - Chapter 4 - OkiNet for TCP/IP
Enabling/Disabling Protocols
To enable or disable protocols on the OkiLAN 6020e,
select the Protocols tab. Select each protocol you wish
to enable. If you disable a protocol, the OkiLAN 6020e
will no longer communicate using that protocol.
SNMP Trap Configuration
The SNMP Trap option allows configuration of traps.
Traps are unsolicited information concerning the
OkiLAN 6020e. Traps can be sent to an SNMP
manager or be broadcast to all hosts on the local
segment.
To configure SNMP traps, select the SNMP Traps tab.
Note: SNMP options need to be configured only if
you are managing an OkiLAN 6020e or getting
system information using SNMP.
Protocol
Select the protocol for which you wish to configure
trap information.
IV - 32
OKI OkiLAN 6020e User’s Guide
Section 4 - Chapter 4 - OkiNet for TCP/IP
Trap Destination
• TCP/IP Protocol - Enter the IP address to which
traps will be sent. The IP address must follow the
format XXX.XXX.XXX.XXX, where each XXX is
a number from 0 to 255. To broadcast traps to all
hosts on the local subnet, enter 255.255.255.255.
• NetWare Protocol - Enter the network number and
hardware address, respectively, to which traps will
be sent. To broadcast traps to all addresses on all
networks, enter FFFFFFFF (8 characters) in the first
field and FFFFFFFFFFFF (12 characters) in the
second field. To broadcast traps to all addresses on a
specific network, enter the network number in the
first field and then FFFFFFFFFFFF (12 characters)
in the second field.
Ports to Trap
Select the output ports on which you wish traps to be
active.
Select the printer traps to be activated. The following
printer error conditions may cause a printer trap to
occur:
• On-line
• Off-line
• No Printer Attached
• Paper Out
• Paper Jam
• Door Open
• Toner Low
• Printer Error
The toner low, door open and paper jam traps require
that your printer be set to automatic emulation
switching (the default) or PCL emulation.
OKI OkiLAN 6020e User’s Guide
IV - 33
TCP/IP
Printer Traps
Section 4 - Chapter 4 - OkiNet for TCP/IP
Saving the Configuration
Once all settings have been defined, select OK. The
settings will be saved and you will be returned to the
main OkiNet for TCP/IP screen.
Displaying OkiLAN 6020e Diagnostic
Information
To view OkiLAN 6020e diagnostic information, double
click on Diagnostics from the Print Server pull-down
menu on the main OkiNet TCP/IP screen. Diagnostic
information is available on the following topics:
• Printer
• Print Server
• Protocols
• Network
• Statistics
• Technical Support
• System
Printing a Configuration Sheet
The configuration sheet provides current network, print
server and printer information. To print a configuration
sheet, select the OkiLAN 6020e from the list of
available print servers. Select Print Configuration
Sheet from the Print Server menu bar.
Resetting the OkiLAN 6020e
To reset the OkiLAN 6020e, select the OkiLAN 6020e
from the list of available print servers. From the Print
Server menu bar, select Reset.
CAUTION: Make sure there are no print jobs active
when you reset the OkiLAN 6020e. All protocols will
be restarted. If you attempt a reset while a job is
printing, the job may not print successfully.
IV - 34
OKI OkiLAN 6020e User’s Guide
Section 4 - Chapter 4 - OkiNet for TCP/IP
Restoring Factory Default Settings
To restore the OkiLAN 6020e to factory default
settings, select the OkiLAN 6020e from the list of
available print servers. From the Print Server menu bar,
select Reset.
From the Reset Print Server screen, choose one or
more of the following options:
Output Ports
Restores settings related to output ports such as port
name and output type.
TCP/IP
Restores settings specific to the TCP/IP protocol
configuration such as the IP address and subnet mask.
NetWare
Restores settings specific to the NetWare protocol
configuration such as the mode and default file server.
Banyan VINES
Restores settings specific to the VINES protocol
configuration such as user name and print service
names (may apply to other OkiLAN print server
models).
Restores settings specific to the EtherTalk protocol
configuration such as the name and zone.
Once you have chosen the desired options, select
Restore. To completely restore the print server to
factory default settings, select all items in the list.
CAUTION: Make sure there are no active print jobs
when you select Restore Factory Defaults. If you reset
the OkiLAN 6020e while a job is printing, the job may
not print successfully.
OKI OkiLAN 6020e User’s Guide
IV - 35
TCP/IP
EtherTalk
Section 4 - Chapter 4 - OkiNet for TCP/IP
Creating Customized Views
OkiNet for TCP/IP allows users to create multiple
customized views for the list of OkiLAN 6020e
products. By creating different views, the user can
narrow the information displayed to that which is of
highest priority. These views can be saved and selected
as needed.
OkiNet has two predefined views. The All Print Servers
view displays all the print servers available on your
local network. The Unconfigured Print Servers view
displays only the print servers on the local network that
have not been configured.
Creating a New Customized View
To create a new view, select New from the View menu.
Enter a name for the new customized view. Define
Filters, Sorts, Column, Search information and
Refresh rates. Select OK to save this view.
Selecting an Existing View
To select an existing view, choose Select from the View
menu. Highlight the view you wish to open and select
OK. The OkiLAN 6020e list will be displayed as
described by the view selected.
IV - 36
OKI OkiLAN 6020e User’s Guide
Section 4 - Chapter 4 - OkiNet for TCP/IP
Modifying View Settings
Before modifying the settings, select the name of the
view you wish to edit from the Name field.
Sort
The Sort option displays the OkiLAN 6020e list in a
specific order. The list can also be sorted by clicking on
the column by which you wish to sort the list. A sort
order can be defined on columns displayed on the main
OkiNet for TCP/IP screen.
Display Filter
The filter option displays only those print servers
matching specific criteria. The print server list can be
filtered by any of the following:
Enter for the Filter Value
<No Filter>
No value
DateCode
Four digits followed by a letter (e.g. 9502B)
Default Gateway
XXX.XXX.XXX.XXX; use “*” for
groups / subnets
H/W Address
12 hexadecimal digits for the Ethernet address
IP Address
XXX.XXX.XXX.XXX; use “*” for
groups / subnets
Name
SNMP System Name (sys name) for the print
server
Product #
Select from the list of product number(s)
Product Type
Select from the list of product types
Status
Select from the list of status conditions
Subnet Mask
XXX.XXX.XXX.XXX; use “*” for
groups / subnets
OKI OkiLAN 6020e User’s Guide
TCP/IP
Filter By
IV - 37
Section 4 - Chapter 4 - OkiNet for TCP/IP
Search Filter
The Search option defines the criteria for identifying
OkiLAN 6020e products on the network.
• Search Local Network - This method broadcasts a
discovery request to locate all OkiLAN 6020e print
servers on the local network. All OkiLAN 6020e
print servers that respond are placed in the list. If
you have a large number of OkiLAN 6020e print
servers on your local network and wish to minimize
network traffic, do not select this option.
• Specify Devices/Networks - This method adds
specific print servers (or groups of print servers) to
the list. If you have OkiLAN 6020e print servers that
are not on the local network (i.e. across routers), the
address of each OkiLAN 6020e must be entered in
order to locate and insert it into the list.
Example: 192.168.42.24
When specifying a subnet, enter a * for the last (fourth)
part of the IP address. OkiNet for TCP/IP will search
every address on the subnet.
Example: 192.168.42.*
Select Add to enter these addresses.
Columns
Column information for each print server can be
modified.
To define the location of a new column, select the
location in the Columns Displayed field where you
wish the new column to be inserted, then select Add. If
no location is selected, the new column will be added to
the end of the list and the column will be displayed to
the right of the last column on the screen.
IV - 38
OKI OkiLAN 6020e User’s Guide
Section 4 - Chapter 4 - OkiNet for TCP/IP
For example, if you currently have three columns
displayed and you wish to add a fourth column to the
far left of the screen, follow these steps:
1. Select the first column in the Columns Displayed
field.
2. Select the column to be added from the Columns
Available field.
3. Select Add.
Columns may also be removed by selecting Remove
from the Columns Available field.
Refresh
Permanently Defining SNMP Access
Information
Access to OkiLAN 6020e configuration and diagnostic
information is determined by using community names.
The Special Options window is used to permanently
define access information so that it does not need to be
entered each time the OkiLAN 6020e is accessed. To
Get and/or Set information on the OkiLAN 6020e
through OkiNet for TCP/IP, community names must
match the community names assigned to the OkiLAN
6020e.
OKI OkiLAN 6020e User’s Guide
IV - 39
TCP/IP
The refresh rate defines how often the OkiNet for TCP/
IP utility updates the main print server list. To define a
refresh rate, select Automatic Refresh and enter the
refresh rate in the field provided. Decide how
frequently to refresh the screen based on factors such
as network traffic and desire for most recent
information.
For example, if traffic on your network is not an issue
and the most current information is desired, set the
refresh rate to 1 so that the screen is updated every
minute.
If network traffic is an issue, you may wish to set the
refresh rate to 10. This would update the screen every
ten minutes and minimize network traffic.
Section 4 - Chapter 4 - OkiNet for TCP/IP
To configure OkiNet for TCP/IP to use the correct
community names, select Special Options from the
File menu.
IP Address
This field displays the address of each OkiLAN 6020e
for which OkiNet for TCP/IP has defined access. To
add a new IP address to this list, select the Add button.
Get Community Name
Enter the Get Community Name necessary to access
the OkiLAN 6020e or group of OkiLAN 6020e
products selected.
Set Community Name
Enter the Set Community Name necessary to access the
OkiLAN 6020e or group of OkiLAN 6020e print
servers selected.
Add
Select the Add button to define access to a new
OkiLAN 6020e or a group of OkiLAN 6020e print
servers. The IP address must follow the format
XXX.XXX.XXX.XXX, where each XXX is a number
from 0 to 255. Use * to specify groups/subnets.
For example: To add a single OkiLAN 6020e, enter
198.168.42.24. To add a group of OkiLAN 6020e print
servers, enter 198.168.42.*.
Delete
The Delete button deletes an OkiLAN 6020e access
entry in the IP address.
IV - 40
OKI OkiLAN 6020e User’s Guide
Section 4 - Chapter 4 - OkiNet for TCP/IP
Configuring the Discovery UDP Port
Number
In order to discover OkiLAN 6020e print servers on the
network, OkiNet for TCP/IP communicates with the
OkiLAN 6020e print servers on a UDP port number.
Normally, using this port number should not interfere
with other devices on the network. If there are
problems using the given port number, select a new
number.
Note: Windows NT will not permit the use of Port 9
for discovery. Select one of the other available
ports.
Starting a Telnet Session
A simple telnet interface has been provided to
communicate with devices supporting telnet. A telnet
session can be started by selecting the OkiLAN 6020e
from the print server list and choosing the Telnet
Session option from the Tools menu. For more
information about how to configure an OkiLAN 6020e
using telnet, see Chapter 6.
OKI has provided a stand-alone BOOTP server to help
assign IP addresses to the OkiLAN 6020e.
To access the stand-alone BOOTP server, select
BOOTP Server from the Tools menu or run the
program bootpsrv.exe from Windows. The BOOTP
server displays all BOOTP activity on the local
network. It responds to BOOTP requests for which the
hardware address has been entered into the BOOTP
file. For more information, view the on-line help for the
BOOTP server.
OKI OkiLAN 6020e User’s Guide
IV - 41
TCP/IP
Starting the BOOTP Server
Section 4 - Chapter 5 - Web Configuration
Chapter 5
Web Configuration
If the DHCP protocol is enabled as a default, the print
server may be accessed through an ordinary Internet
Web browser, such as Netscape Navigator or Microsoft
Internet Explorer. See Section II, Chapter 4, OkiLAN
6020e Web Configuration, for more information.
IV - 42
OKI OkiLAN 6020e User’s Guide
Section 4 - Chapter 6 - Telnet Configuration
Chapter 6
Telnet Configuration
Overview
The OkiLAN 6020e Configuration utility (telnet)
provides system, network and printer status information
and allows you to change the configuration of your
OkiLAN 6020e.
Note: The configuration of your OkiLAN 6020e is
password protected. Only authorized users can
alter the configuration.
1. To run the configuration utility, type the following:
telnet <OkiLAN 6020e_name>
2. Replace OkiLAN 6020e_name with the IP address or
the host name assigned to the OkiLAN 6020e you
want to configure.
A screen will appear displaying an introductory
message. When prompted for a password, enter
OkiLAN. The password will not be echoed.
3. When you are finished typing your password, press
Enter. For password verification, you will then be
asked to enter your password again.
Each time you use the utility, you will be asked to
enter your password. If you fail to enter the
password correctly in three attempts, your
connection with the OkiLAN 6020e will be closed.
4. Once your password is entered and accepted, a list of
options will display. An explanation of each option
follows.
OKI OkiLAN 6020e User’s Guide
IV - 43
TCP/IP
Running a Telnet Session
Section 4 - Chapter 6 - Telnet Configuration
*****************************************
OkiLAN 6020e Configuration Utility
1. Show Network/Printer Information
2. Change Password
3. Specify Print Server IP Address
4. Specify Subnet Mask For Your Network
5. Identify Default Gateway IP Address
6. Configure Port
7. TCP Connection Configuration
8. Download New Firmware
9. Restore to Factory Defaults
To select an option above, type its number and press
Enter.
To quit, press Enter.
*****************************************
Showing Network/Printer Information (Option 1)
This option displays current network and printer
information.
Changing the Password (Option 2)
This option allows you to change the password required
for access to this utility. We recommend that you
change your password periodically, especially if
security may have been compromised. Type a password
(5-24 characters long). The characters you type will not
appear on the screen. When you are done typing, press
Enter. You will be asked to enter your password again.
This allows you to verify your password was typed
correctly.
You must save your changes when you exit the utility
for the new password to take effect.
IV - 44
OKI OkiLAN 6020e User’s Guide
Section 4 - Chapter 6 - Telnet Configuration
Specify Print Server IP Address (Option 3)
This option allows you to select the method the
OkiLAN 6020e uses to obtain its IP address or to set a
permanent IP address. If the OkiLAN 6020e has been
configured to use a permanent IP address, a DHCP,
RARP or BOOTP server does not need to be available
when the OkiLAN 6020e is powered on.
If you change the IP address, the change will remain
undetected until the OkiLAN 6020e is reset or is
powered off and on.
Remember, when choosing a permanent IP address:
• The IP address must follow the format
XXX.XXX.XXX.XXX, where each XXX is a
number between 0 and 255.
• If you select an invalid IP address you may not be
able to access the OkiLAN 6020e.
• You can also use OkiNet for TCP/IP, OkiNet for
NetWare or the Banyan VINES OkiNet for VINES
utilities (may apply to other OkiLAN print server
models) to set a permanent IP address.
Note: If you select an invalid IP address you may not
be able to access the OkiLAN 6020e. Use this
option with care!
If your network environment includes subnets, you will
want to set the subnet mask.
The subnet mask must follow the format
XXX.XXX.XXX.XXX, where each XXX is a number
between 0 and 255.
The default subnet mask is 0.0.0.0. The OkiLAN 6020e
interprets a subnet mask of 0.0.0.0 or 255.255.255.255
as no subnet mask specified.
If you change the subnet mask, the change will remain
undetected until the OkiLAN 6020e is reset or is power
cycled.
OKI OkiLAN 6020e User’s Guide
IV - 45
TCP/IP
Specify the Subnet Mask for Your Network
(Option 4)
Section 4 - Chapter 6 - Telnet Configuration
Note: If you select an invalid subnet mask you may
not be able to access the OkiLAN 6020e. Use
this option with care!
Identify Default Gateway IP Address (Option 5)
If your local network is attached to other networks, you
must specify the address of your default gateway.
Whenever packets need to be sent to another network,
the default gateway is used.
The gateway address must follow the format
XXX.XXX.XXX.XXX, where each XXX is a number
between 0 and 255.
When the default gateway is changed, it will remain
undetected until the OkiLAN 6020e is reset or is power
cycled.
Note: If you select an invalid default gateway or the
default gateway goes down, the OkiLAN
6020e may not be able to communicate with
non-local networks.
Configure Port (Option 6)
After the Configure menu appears, you can access the
following configuration option screens.
Specify Configuration Page Language
This option enables you to select how the OkiLAN
6020e configuration pages should be printed: Text
(default), PCL, PostScript, or OFF.
Configure Language Switching
This option asks you to select the language of your
printer. For a description of language switching
options, see pages IV-28 and IV-29.
IV - 46
OKI OkiLAN 6020e User’s Guide
Section 4 - Chapter 6 - Telnet Configuration
Configure Printer Type
This option enables you to indicate the printer type to
which the OkiLAN 6020e is connected. Printer choices
are:
1. Oki Data printer.
2. Custom printer.
• Language Switching Sequence - If you select
Custom Printer from the Configure Printer Type
screen, you must indicate the switching sequence to
be used for both PCL and PostScript. This is only
necessary if language switching is set to something
other than OFF.
TCP Connection Configuration (Option 7)
TCP Connection Timeout
This is used to sever network TCP/IP Connections that
are idle for more than a specified period of time
(between 1 and 3600 seconds). You can also disable
timeout checking. Under most conditions you will want
to leave this function enabled.
Raw Port Number
Set the port number where the raw port connections
will be accepted.
This option is provided for future product
modifications and enhancements. It requires an update
file from OKI.
CAUTION: Do NOT use this option without having
the upgrade files on hand. The OkiLAN 6020e will be
locked in download mode. This is indicated by a
flashing orange-green Status LED.
The latest firmware and utilities are available through:
• World Wide Web: http://www.okidata.com
Firmware update instructions are available with the
download file.
OKI OkiLAN 6020e User’s Guide
IV - 47
TCP/IP
Download New Firmware (Option 8)
Section 4 - Chapter 6 - Telnet Configuration
Restore to Factory Default Configuration (Option 9)
This option automatically restores the OkiLAN 6020e
to its original factory defaults. Be aware that when you
restore the OkiLAN 6020e to the original factory
default settings, only the TCP/IP protocol and output
port information is restored and your TCP/IP password
and IP address are erased.
CAUTION: Make sure that no print jobs are active
when you select Restore to Factory Defaults.
Performing this operation will restore parameters for
the TCP/IP protocol to factory defaults. If you reset
the OkiLAN 6020e while a job is printing, the job may
not print successfully.
IV - 48
OKI OkiLAN 6020e User’s Guide
Section 4 - Appendix A - Troubleshooting
Appendix A
Troubleshooting
Main Status Indicator
Upon power-up, the main status indicator flashes
orange. It changes to green when the OkiLAN 6020e
passes self-test. The indicator stays orange if the
OkiLAN 6020e fails self-test. If the indicator turns
solid orange due to an error, a configuration sheet will
be printed automatically. Check the error message
reported on the configuration sheet.
In most cases, the best way to restore the OkiLAN
6020e to factory defaults is via telnet. However, if you
are unable to connect to the device because of a
configuration error, use the following method which
does not require a network connection.
To restore the OkiLAN 6020e to factory defaults,
complete the following steps:
1. Power down the OkiLAN 6020e.
2. While holding in the Print Configuration Sheet
Test button, power up the OkiLAN 6020e. Hold the
button until the status indicator turns solid green.
3. Power cycle the OkiLAN 6020e. It will have
restored itself to defaults.
OKI OkiLAN 6020e User’s Guide
IV - 49
TCP/IP
Restoring the OkiLAN 6020e to
Factory Defaults
Section 4 - Appendix A - Troubleshooting
Unable to Assign IP Address
Gleaning
If you ping the device and are not getting a response,
the glean is not working. Check the following possible
problems:
• Verify the ARP table contains the correct
hardware and IP address by running the ‘arp -a’
command.
• If you are getting a response, but the OkiLAN
6020e LED is still blinking green, power down
the print server and try the ping again. There
might be a different device answering to the ping.
• Verify the OkiLAN 6020e is on the same subnet
as the computer running the ping.
• The glean will not work if the OkiLAN 6020e has
already defaulted to an IP address two minutes
after power up. The LED will turn solid green and
the device will print a configuration page. Power
cycle the device and try the glean again.
RARP or BOOTP
If you are using a BOOTP or RARP server and the
OkiLAN 6020e is not getting an IP address, check the
following:
• Verify the BOOTP/RARP configuration files are
correctly set up (“/etc/ethers” and “/etc/hosts” for
RARP and “/etc/bootptab” for BOOTP). Verify
the files have the correct hardware address of the
OkiLAN 6020e. If using RARP, check that the
hostnames are the same between the “/etc/ethers”
and “/etc/hosts” files.
IV - 50
OKI OkiLAN 6020e User’s Guide
Section 4 - Appendix A - Troubleshooting
If you are running UNIX, try the following methods
with the BOOTP server (check the documentation for
your particular UNIX flavor).
• Verify the BOOTP server has reread the “/etc/
bootptab” file when the new entry was added. If
the BOOTP server was running when you added
the new entries, the server might not have reread
the new bootptab file. Try sending the SIGHUP
signal to the running BOOTP server. For example,
kill -HUP <process id of bootpd> tells it to reread
“/etc/bootptab”. Most BOOTP servers support this
option. Check your local BOOTP documentation.
If this does not work, restart the BOOTP server
(kill and restart the process).
• Some BOOTP servers will write their internal
bootptab tables to a file when they receive a
SIGUSR1 signal. You can check this file to verify
the hardware and IP address are correct. You can
use the kill command to send signals. For
example, kill -USR1 <process id of bootpd>.
Check your documentation for more information.
• Check the system’s syslog file. Some BOOTP
servers will write error messages into the syslog
file.
Example:
Sep 6 14:38:43 bootpd[17565]: hardware
address not found: 004068175042
This message appears when the BOOTP server
received a request from a device not in its internal
bootptab tables.
OKI OkiLAN 6020e User’s Guide
IV - 51
TCP/IP
UNIX BOOTP
Section 4 - Appendix A - Troubleshooting
Static Route Entry
If the OkiLAN 6020e has printed a configuration page
showing the default address, but it cannot be reached
through telnet, check the following:
• Display the host’s routing tables with the ‘netstat r’ command. Verify the route has been set
correctly.
• If the route is set correctly, try pinging the device.
• Verify the OkiLAN 6020e is on the same subnet
as the host from which you are telneting. As a
drastic measure, try creating an isolated subnet
with your host and the OkiLAN 6020e. If you are
using 10BASE2, run the cable directly from the
host to the OkiLAN 6020e. If using 10/100BASE-T
cabling, connect the host to the OkiLAN 6020e
through a hub not connected to any other host.
• If the static route has been set up and can telnet to
the OkiLAN 6020e, but your changes do not seem
to be saved, check the host’s routing tables. You
might have telneted to a different OkiLAN 6020e
than the one you intended. While in telnet, select
the second menu option, Show Network/Printer
Information. The hardware address and serial
number are displayed. Verify they are the same as
the unit you are configuring.
• Turn off the OkiLAN 6020e you want to
configure. Run telnet again. If you reach a
different device, there is an IP address conflict.
• If you are able to ping to the OkiLAN 6020e, but
are unable to telnet, the IP address is probably
being shared with another device that does not
support telnet.
IV - 52
OKI OkiLAN 6020e User’s Guide
Section 4 - Appendix A - Troubleshooting
OkiNet for TCP/IP - Winsock Errors
• If you see an error before OkiNet for TCP/IP appears
on the screen, try setting a host name in the host’s file
in the Windows directory (check the documentation
for your Windows TCP/IP stack).
• If you have difficulty seeing a particular OkiLAN
6020e, try moving the device onto the same subnet
as the computer running the utility.
• If OkiNet for TCP/IP gives you the Winsock error:
Could not bind to socket, use the Special Options
dialog under the File menu to change the Discovery
UDP Port to a different port number.
Hardware Error Messages
ST: Cable not connected
System CRC Failed
The OkiLAN 6020e has failed.
• Power cycle the OkiLAN 6020e once. If the error
continues, call Oki Data Customer Support at
1-800-OKI-DATA (1-800-654-3282).
OKI OkiLAN 6020e User’s Guide
IV - 53
TCP/IP
Self-test has determined that the network cable is not
connected.
• Check the cable connection to the OkiLAN
6020e.
• Move the OkiLAN 6020e to another known
working node.
If you find the cable is connected and you are still
receiving this message or any other “ST:” error
message, power cycle the OkiLAN 6020e. If the error
continues, call Oki Data Customer Support at
1-800-OKI-DATA (1-800-654-3282).
Section 4 - Appendix A - Troubleshooting
Printing a Configuration Page
If the status indicator turns solid orange due to an error
and no configuration page is printed, your printer may
be configured for PostScript operation. If so, you must
re-configure your printer for standard ASCII mode so
that the configuration page can be printed.
If you do not know the configuration of the OkiLAN
6020e or you think the configuration has been changed,
use the following method for printing a configuration
page:
• With the network cable detached, attach the
OkiLAN 6020e to a printer and power cycle the
print server. When the OkiLAN 6020e powers up,
it will detect the detached network cable and print
a configuration sheet. If no configuration sheet is
printed and the indicator has turned green, check
the printer and verify it is ready to print. If you
are using boot protocols (RARP or BOOTP) to
assign the IP address, the IP address will be listed
as Using network protocol (0.0.0.0) on the
configuration page.
Unable to Print
LPR/LP
• If the indicator blinks green, the OkiLAN 6020e
is receiving data. If nothing is actually printing,
check the printer settings. For example, if you are
using a PostScript printer, verify the OkiLAN
6020e is also set to PostScript.
• Try pinging the OkiLAN 6020e by its IP address
(not the hostname). This will verify the unit is
functioning on the network.
• If the ping succeeds, try ftping a test file to the
print server. If the ping fails, you might have a
configuration problem with the OkiLAN 6020e
(the IP address or gateway address might be
incorrect, etc.).
IV - 54
OKI OkiLAN 6020e User’s Guide
Section 4 - Appendix A - Troubleshooting
• If the ftp succeeds, there is a problem with the lpr/
lp setup. Verify the hostname or IP address is
correctly set for the queue. Try doing an lpstat
(System V) or lpq (BSD) to query the status of the
OkiLAN 6020e.
FTP
TCP/IP
• If the indicator blinks green, the printer is
receiving data. If nothing is actually printing,
check the printer settings. For example, if you are
using a PostScript printer, verify the OkiLAN
6020e is set to PostScript also.
• Try pinging the device by its IP address (not the
hostname). This will verify the OkiLAN 6020e is
functioning on the network.
• If you cannot connect over ftp but the ping
succeeds, try telneting to the OkiLAN 6020e and
print a configuration page to verify settings. If
that fails, you might have a TCP/IP configuration
problem with the OkiLAN 6020e.
OKI OkiLAN 6020e User’s Guide
IV - 55
Section 4 - Appendix B - Application Considerations
Appendix B
Application Considerations
Overview
This appendix provides application notes for the
following:
• Assigning the OkiLAN 6020e IP Address with
BOOTP
• Assigning the OkiLAN 6020e IP Address with
RARP
• Using the Windows NT v3.5 LPR Print Monitor
• Configuring HP-UX v8.07 for Printing
• Configuring HP-UX v9.xx for Printing
• Configuring HP-UX v10.xx for Printing
• Configuring SCO UNIX for Printing
• Configuring IBM’s AIX ver. 3.x for Printing
• Configuring the OkiLAN 6020e for Solaris
Printing
• Configuring Sun-OS v4.1.x or Ultrix v4.2 for
Printing
IV - 56
OKI OkiLAN 6020e User’s Guide
Section 4 - Appendix B - Application Considerations
Assigning the OkiLAN 6020e IP
Address with BOOTP
BOOTP is an acronym for BOOTStrap Protocol.
Every TCP/IP network device is required to have a
unique 32-bit IP address assigned to it. TCP/IP network
devices will have both an IP address and a 48 bit
Ethernet/Token-Ring (network hardware) address.
Ethernet addresses usually cannot be configured and
are hard coded by the manufacturer of the device.
BOOTP is a protocol used by devices that know their
network hardware address, but do not know their IP
address. When powering up on a network, a device that
uses BOOTP will broadcast its network hardware
address in a BOOT request packet. A BOOTP server
(which may be a UNIX workstation) will respond with
an IP address. The device will then know its IP address
and use this address to perform subsequent TCP/IP
transactions.
Address Formats
Network hardware addresses are 48-bits and are
expressed in 6 bytes (hexadecimal format) usually
separated by colons. Each hexadecimal byte has a
range from 00 to FF.
OKI OkiLAN 6020e User’s Guide
IV - 57
TCP/IP
Note: Once the OkiLAN 6020e has been assigned an
IP address, the OkiLAN 6020e configuration
utility (which is run by accessing the OkiLAN
6020e using telnet) or OkiNet for TCP/IP will
allow you to change and/or make the IP
address permanent. This means that a BOOTP
server needs to be available only during
installation of the OkiLAN 6020e.
Section 4 - Appendix B - Application Considerations
A name can be arbitrarily assigned to any device on a
network. The following examples use the name
OKIPRINTER. Remember that this name is arbitrary; a
customer can assign any name they wish.
/etc/bootptab: The “/etc/bootptab” file has entries
where each entry maps a network
hardware address to an IP address.
Example:
OKIPRINTER:\
ht=ether:\
ha=0040681750A4:\
ip=192.168.42.55
The ht signifies hardware type. For the OkiLAN 6020e,
it will always be ether for an Ethernet device and token
for a Token-Ring device. The ha signifies the network
hardware address. For BOOTP, the network hardware
address must be represented without the colons
between each byte. The ip part of the entry is where the
IP address is specified. There are several other
parameters that can be specified in a bootptab entry.
However, the three parameters shown here are the only
ones required for OkiLAN 6020e installation.
The following sequence of events occurs during the
power up of the OkiLAN 6020e using BOOTP.
1. An OkiLAN 6020e powers up but does not know its
IP address. (It does know its network hardware
address.)
2. The OkiLAN 6020e sends out a BOOTP request
packet with its network hardware address. For this
example, the network hardware address is
00:40:68:17:50:A4.
3. The bootpd daemon running on a BOOTP server
(which in this example is a UNIX workstation) sees
the BOOTP request along with the network
hardware address. It looks up the network hardware
address in the “/etc/bootptab” file. The bootpd
daemon finds the associated IP address of the device
in the bootptab file.
IV - 58
OKI OkiLAN 6020e User’s Guide
Section 4 - Appendix B - Application Considerations
4. The bootpd daemon transmits a response to the
OkiLAN 6020e with the IP address 192.168.42.55.
The OkiLAN 6020e will use this IP address for all
subsequent transmissions.
For these steps to work properly, at least one BOOTP
daemon (bootpd) must be running on the BOOTP
server. To test whether a BOOTP daemon is running on
the BOOTP server, use the ps command with the show
all process option within fifteen minutes of an
attempted BOOTP request. Unfortunately, the ps
options differ from one UNIX workstation to another.
Perform a man ps at the UNIX prompt to consult a
manual page on the ps command for a particular
workstation. If bootpd is not running on a workstation,
type man bootpd at the UNIX prompt to consult a
manual page on the BOOTP daemon and how to start
it.
Often TCP/IP networks are divided into subnets.
BOOTP does not work across subnets. When installing
an OkiLAN 6020e, make sure the following criteria are
met for BOOTP to work properly.
• Both the BOOTP server and the OkiLAN 6020e
are physically attached to the same subnet.
• The IP address assigned to the OkiLAN 6020e
and the IP address of the BOOTP server belong to
the same subnet.
OR
• Your router(s) are configured to forward BOOTP
packets between the OkiLAN 6020e’s subnet and
the subnet of the host running the BOOTP server.
OKI OkiLAN 6020e User’s Guide
IV - 59
TCP/IP
Limitations
Section 4 - Appendix B - Application Considerations
Configuring the OkiLAN 6020e IP
Address with RARP
RARP is an acronym for Reverse Address Resolution
Protocol. Every TCP/IP network device must have a
unique 32-bit IP address. TCP/IP network devices will
have both an IP address and a 48-bit Ethernet (network
hardware) address. Ethernet addresses usually cannot
be configured and are hard coded by the manufacturer
of the device. RARP is a protocol used by devices that
know their network hardware address, but do not know
their IP address. When powering up on a network, a
device that uses RARP will broadcast its network
hardware address in a RARP request message. A RARP
server (which may be a UNIX workstation) will
respond with an IP address. The device will then know
its IP address and use this address to perform
subsequent TCP/IP transactions.
Note: Once the OkiLAN 6020e has been assigned an
IP address, the OkiLAN 6020e configuration
utility (which is accessed by telneting to the
OkiLAN 6020e) or OkiNet for TCP/IP will
allow you to change and/or make the IP
address permanent. This means that a RARP
server needs to be available only during
installation of the OkiLAN 6020e.
Address Formats
Network hardware addresses are 48-bits and are
expressed in 6 bytes in hexadecimal format usually
separated by colons. Each hexadecimal byte has a
range from 00 to FF.
Example: 00:02:16:17:50:A4
IP addresses are 32-bits and are expressed in 4 bytes in
decimal format usually separated by periods. Each
decimal byte has a range from 0 to 255.
Example: 192:168:42:55
IV - 60
OKI OkiLAN 6020e User’s Guide
Section 4 - Appendix B - Application Considerations
The purpose of RARP is to look up a 32-bit IP address
given a 48-bit network hardware address. The RARP
server (which is usually a UNIX workstation running a
rarpd daemon) performs this function using two
configuration files and one or more daemons. The
configuration files are “/etc/hosts” and “/etc/ethers” and
the daemon is called rarpd. A name can be assigned to
any device on a network and is arbitrary. For the
following examples the name used for the OkiLAN
6020e is OKIPRINTER. Remember that this name is
arbitrary; a customer can assign any name.
/etc/hosts: The “/etc/hosts” file is where each entry
maps a host name to an IP address. An
example entry is shown below.
192.168.42.55 OKIPRINTER
/etc/ethers: The “/etc/ethers” file is where each entry
maps a host name to a network hardware
address. An example entry is shown below.
00:02:16:17:50:A4 OKIPRINTER
The following sequence of events occurs during the
power up of the OkiLAN 6020e using RARP:
1. The OkiLAN 6020e powers up but does not know its
IP address. However, it does know its network
hardware address.
2. It sends out a RARP request message with its
network hardware address. For this example, the
OkiLAN 6020e address is 00:02:16:17:50:A4.
3. The rarpd daemon running on a RARP server (in this
example the RARP server is a UNIX workstation)
sees the RARP request along with the network
hardware address in the “/etc/ethers” file. The rarpd
daemon finds the host name, OKIPRINTER, listed
as the name associated with the network hardware
address.
OKI OkiLAN 6020e User’s Guide
IV - 61
TCP/IP
Configuration Files
Section 4 - Appendix B - Application Considerations
4. The rarpd then consults the “/etc/hosts” file and
looks up the name OKIPRINTER. It finds an IP
address (in this case 192.168.42.55) associated with
the name OKIPRINTER.
5. The rarpd daemon transmits a response to the
OkiLAN 6020e with the IP address 192.168.42.55.
The OkiLAN 6020e will then use this IP address for
all subsequent transmissions.
For all these steps to work properly, at least one RARP
daemon (rarpd) must be running on the RARP server.
On most UNIX systems, this can be tested by using the
ps command with the show all processes option.
Unfortunately, the ps options differ from one UNIX
workstation to another. Perform a man ps at the UNIX
prompt to consult a manual page on the ps command
for a particular workstation. If rarpd is not running on a
workstation, type man rarpd at the UNIX prompt to
consult a manual page on the RARP daemon and how
to start it.
Limitations
Often TCP/IP networks are divided into subnets. RARP
does not work across subnets. When installing an
OkiLAN 6020e, make sure the following two criteria
are met for RARP to work properly.
1. Both the RARP server and the OkiLAN 6020e are
physically attached to the same subnet.
2. The IP address assigned to the OkiLAN 6020e and
the IP address of the RARP server belong to the
same subnet.
IV - 62
OKI OkiLAN 6020e User’s Guide
Section 4 - Appendix B - Application Considerations
Configuring HP-UX v8.07 for Printing
with the OkiLAN 6020e
This application note describes the configuration of the
printing system on the HP-UX ver. 8.07 of the UNIX
operating system. For clarity and brevity, the following
specific names will be used to represent general
devices or concepts.
• lj4 - The local queue name on the HP-UX system
to which print jobs that are destined for a printer
attached to the OkiLAN 6020e will be directed.
• OKIPRINTER - The host name of the remote
system which is the OkiLAN 6020e. For example,
to telnet to the OkiLAN 6020e and invoke the
OkiLAN 6020e Configuration utility, you would
type telnet OKIPRINTER. A host name is not
required for the OkiLAN 6020e, the IP Address
may be used.
• yourqueuename - This is the name of the queue
on the OkiLAN 6020e and must end with 1, 2, 3
or 4, depending on the port selected to service the
print jobs.
If FF, LF or NF are the last two letters of the
queue name, the job will be converted
accordingly. See pages IV-15 and IV-16 for more
information on remote queue names.
Before you proceed, the following prerequisites must
be met. Most of the time, steps 2 through 5 are already
configured since the HP-UX system is on a TCP/IP
network. Do not perform steps 2 through 5 unless the
installation procedure fails!
1. The name OKIPRINTER and the IP address
assigned to the OkiLAN 6020e are in the
“/etc/hosts” file on the HP-UX system.
OKI OkiLAN 6020e User’s Guide
IV - 63
TCP/IP
Prerequisites
Section 4 - Appendix B - Application Considerations
2. Make sure the rlp process is not running by typing at
the UNIX prompt:
ps -e | grep rlp
If rlp is not running, you will not see any output after
executing this command.
If rlp is running (that is, if you see output after
executing this command), kill the process with the
command:
kill -15 process_number
3. Make sure the following entry is in the
“etc/inetd.conf” file:
printer stream tcp nowait root /usr/lib/
rlpdaemon rlpdaemon -I
If the rlp daemon is not running when a print request
is made, this entry in “/etc/inetd.conf” tells inetd to
auto-start the rlp daemon to service the pending print
request. This is helpful if the daemon was terminated
for some reason. For more information on inetd or “/
etc/inetd.conf”, type man inetd or man inetd.conf.
4. Make sure the following entry is in the
“/etc/services” file
printer 515/tcp spooler
5. Start inetd by typing the following at the UNIX
prompt:
/etc/inetd -c
Procedure
HP-UX uses an interactive utility called SAM (System
Administration Manager) to configure printing. To
configure printing using SAM, do the following:
1. Login to the HP-UX system as root.
2. Invoke the SAM utility by typing sam at the UNIX
prompt. (We suggest you do this at the system
console. SAM uses a screen oriented interface that
works best at the console.)
IV - 64
OKI OkiLAN 6020e User’s Guide
3. Select the following options, in order, from the SAM
menu:
Peripheral Devices ->
Printers and Plotters ->
Actions -> Add a Remote Printer
(Do NOT select Add a Network Printer)
A form appears asking you to define a remote
printer.
4. Enter information into the following fields as
described.
a) Printer name - lj4
This is the name of the printer as referenced by
the local HP machine. Print jobs sent to this
printer are passed to the OkiLAN 6020e.
b) Remote system name - OKIPRINTER
This is the name of the OkiLAN 6020e on the
network. The name must also be in the
“/etc/hosts” file.
c) Remote printer name - yourqueuename
This is the name of the queue on the OkiLAN
6020e and must end with 1, 2, 3, or 4, depending
on the port selected to service the print jobs.
d) Remote cancel model - rcmodel
Used for remote printer job removal.
e) Remote status model - rsmodel
Used for remote printer queue status.
f) Make this the system default printer? (y or n) - n
g) Printer class - (optional)
h) Restrict cancel - (optional)
i) Remote printer on a BSD system? (y or n) - y
Tells the HP-UX system that it is communicating
with a Berkeley style remote printer (such as
LPD).
5. Select Perform Task from the SAM menu.
OKI OkiLAN 6020e User’s Guide
IV - 65
TCP/IP
Section 4 - Appendix B - Application Considerations
Section 4 - Appendix B - Application Considerations
6. Enable the printer you just created using SAM.
Peripheral Devices ->
Printers and Plotters ->
Enable a Printer ...
7. Printer name: — lj4
8. Start the LP request scheduler by typing:
/usr/lib/lpsched
9. Run a test print job to the OkiLAN 6020e with the
following command:
lp -d lj4 filename
Configuring HP-UX v9.xx for Printing
with the OkiLAN 6020e
This application note describes the configuration of the
printing system on the HP-UX ver. 9.xx of the UNIX
operating system. For clarity and brevity, the following
specific names will be used to represent general
devices or concepts.
• lj4 - The local queue name on the HP-UX system
to which print jobs will be directed. The print jobs
are destined for a printer attached to the OkiLAN
6020e.
• OKIPRINTER - The host name of the remote
system which is the OkiLAN 6020e. For example,
to telnet to the OkiLAN 6020e and invoke the
OkiLAN 6020e Configuration utility, you would
type telnet OKIPRINTER. A host name is not
required for the OkiLAN 6020e, the IP Address
may be used.
• yourqueuename - This is the name of the queue
on the OkiLAN 6020e and must end with 1, 2, 3
or 4, depending on the port selected to service the
print jobs.
If FF, LF or NF are the last two letters of the
queue name, the job will be converted
accordingly. See pages IV-15 and IV-16 for more
information on Remote Queue Names.
IV - 66
OKI OkiLAN 6020e User’s Guide
Section 4 - Appendix B - Application Considerations
Before you proceed, the following prerequisites must
be met. Most of the time steps 2 through 5 are already
configured since the HP-UX system is on a TCP/IP
network. Do not perform steps 2 through 5 unless
the installation procedure fails!
1. The name OKIPRINTER and the IP address
assigned to the OkiLAN 6020e are in the
“/etc/hosts” file on the HP-UX system.
2. Make sure the rlp process is not running by typing at
the UNIX prompt:
ps -e | grep rlp
If rlp is not running, you will not see any output after
executing this command.
If rlp is running (that is, if you see output after
executing this command), kill the process with the
command:
kill -15 process_number.
3. Make sure the following entry is in the
“/etc/inetd.conf” file:
printer stream tcp nowait root “/usr/lib/
rlpdaemon” rlpdaemon -i
If the rlp daemon is not running when a print request
is made, this entry in “/etc/inetd.conf” will tell inetd
to auto-start the rlp daemon and service the pending
print request. This is helpful if the daemon died or
was terminated for some reason. For more
information on inetd or “/etc/inetd.conf”, type man
inetd or man inetd.conf.
4. Make sure the following entry is in the
“/etc/services” file:
printer 515/tcp spooler
5. Start inetd by typing the following at the UNIX
prompt:
/etc/inetd -c
OKI OkiLAN 6020e User’s Guide
IV - 67
TCP/IP
Prerequisites
Section 4 - Appendix B - Application Considerations
Procedure
HP-UX uses an interactive utility called SAM (System
Administration Manager) to configure printing.
1. Login to the HP-UX system as root.
2. Invoke the SAM utility by typing sam at the UNIX
prompt. (We suggest you do this at the system
console. SAM uses a screen oriented interface that
works best at the console.)
3. Select the following options from the SAM menu:
Printers and Plotters ->
Printers/Plotters ->
Actions -> Add a Remote Printer
(Do NOT add a Network Printer)
A form appears asking you to define a remote
printer.
4. Enter information into the following fields as
described.
a) Printer name - lj4
The name of the printer as referenced by the local
HP machine. Print jobs sent to this printer are
passed to the OkiLAN 6020e.
b) Remote system name - OKIPRINTER
The name of the OkiLAN 6020e on the network.
The name must also be in the /etc/hosts file.
c) Remote printer name - yourqueuename
This is the name of the queue on the OkiLAN
6020e and must end with 1, 2, 3 or 4, depending
on the port selected to service the print jobs.
d) Remote cancel model - rcmodel
Used for remote printer job removal.
e) Remote status model - rsmodel
Used for remote printer queue status.
f) Printer class - (optional)
g) Make this the system default printer. Leave the
box unchecked.
IV - 68
OKI OkiLAN 6020e User’s Guide
Section 4 - Appendix B - Application Considerations
5.
6.
7.
8.
h) Allow anyone to cancel requests. Check if
desired.
i) Remote printer is on a BSD system. Check this
box.
Tells the HP-UX system that it is communicating
with a Berkeley style remote printer (such as
LPD).
Select the OK button. A status window will outline
the tasks performed to install the queue. When you
see the message task completed, select OK.
Pull down the Lists menu and select Exit.
Select the Exit SAM button.
Test printing to the OkiLAN 6020e with the
following command:
lp -d lj4 filename
This application note describes the configuration of the
printing system on the HP-UX ver. 10.xx of the UNIX
operating system. For clarity and brevity, the following
specific names will be used to represent general
devices or concepts.
• lj4 - The local queue name on the HP-UX system
to which print jobs will be directed. The print jobs
are destined for a printer attached to the OkiLAN
6020e.
• OKIPRINTER - The host name of the remote
system which is the OkiLAN 6020e. For example,
to telnet to the OkiLAN 6020e and invoke the
OkiLAN 6020e Configuration utility, you would
type telnet OKIPRINTER. A host name is not
required for the OkiLAN 6020e, the IP Address
may be used.
OKI OkiLAN 6020e User’s Guide
IV - 69
TCP/IP
Configuring HP-UX v10.xx for
Printing with the OkiLAN 6020e
Section 4 - Appendix B - Application Considerations
• yourqueuename - This is the name of the queue
on the OkiLAN 6020e and must end with 1, 2, 3
or 4, depending on the port selected to service the
print jobs.
If FF, LF or NF are the last two letters of the
queue name, the job will be converted
accordingly. See the section on Remote Queue
Names.
Prerequisites
Before you proceed, the following prerequisites must
be met. Most of the time steps 2 through 5 are already
configured since the HP-UX system is on a TCP/IP
network. Do not perform steps 2 through 5 unless
the installation procedure fails!
1. The name OKIPRINTER and the IP address
assigned to the OkiLAN 6020e are in the
“/etc/hosts” file on the HP-UX system.
2. Make sure the rlp process is not running by typing at
the UNIX prompt:
ps -e | grep rlp
If rlp is not running, you will not see any output after
executing this command.
If rlp is running (that is, if you see output after
executing this command), kill the process with the
command:
kill -15 process_number.
3. Make sure the following entry is in the
“/etc/inetd.conf” file:
printer stream tcp nowait root “/usr/lib/
rlpdaemon” rlpdaemon -i
If the rlp daemon is not running when a print request
is made, this entry in “/etc/inetd.conf” will tell inetd
to auto-start the rlp daemon and service the pending
print request. This is helpful if the daemon died or
was terminated for some reason. For more
information on inetd or “/etc/inetd.conf”, type man
inetd or man inetd.conf.
IV - 70
OKI OkiLAN 6020e User’s Guide
Section 4 - Appendix B - Application Considerations
4. Make sure the following entry is in the
“/etc/services” file:
printer 515/tcp spooler
5. Start inetd by typing the following at the UNIX
prompt:
/etc/inetd -c
HP-UX uses an interactive utility called SAM (System
Administration Manager) to configure printing.
1. Login to the HP-UX system as root.
2. Invoke the SAM utility by typing sam at the UNIX
prompt. (We suggest you do this at the system
console. SAM uses a screen oriented interface that
works best at the console.)
3. Select the following options from the SAM menu:
Printers and Plotters ->
LP Spooler ->
Printers/Plotters ->
Actions -> Add a Remote Printer
(Do NOT add a Network Printer)
A form appears asking you to define a remote
printer.
4. Enter information into the following fields as
described.
a) Printer name - lj4
The name of the printer as referenced by the local
HP machine. Print jobs sent to this printer are
passed to the OkiLAN 6020e.
b) Remote system name - OKIPRINTER
The name of the OkiLAN 6020e on the network.
The name must also be in the
/etc/hosts file.
OKI OkiLAN 6020e User’s Guide
IV - 71
TCP/IP
Procedure
Section 4 - Appendix B - Application Considerations
5.
6.
7.
8.
IV - 72
c) Remote printer name - yourqueuename
This is the name of the queue on the OkiLAN
6020e and must end with 1, 2, 3 or 4, depending
on the port selected to service the print jobs.
d) Remote cancel model - rcmodel
Used for remote printer job removal.
e) Remote status model - rsmodel
Used for remote printer queue status.
f) Printer class - (optional)
g) Make this the system default printer. Leave box
unchecked.
h) Allow anyone to cancel requests. Check if
desired.
i) Remote printer is on a BSD system. Check this
box.
Tells the HP-UX system that it is communicating
with a Berkeley style remote printer (such as
LPD).
Select the OK button. A status window will outline
the tasks performed to install the queue. When you
see the message task completed, select OK.
Pull down the Lists menu and select Exit.
Select the Exit SAM button.
Test printing to the OkiLAN 6020e with the
following command:
lp -d lj4 filename
OKI OkiLAN 6020e User’s Guide
Section 4 - Appendix B - Application Considerations
Configuring SCO UNIX for Printing
with the OkiLAN 6020e
This application note describes the configuration of the
printing system on the Santa Cruz Operation’s (SCO)
version of the UNIX operating system. For clarity and
brevity, the following specific names will be used to
represent general devices or concepts.
• lj4 - The local queue name of the SCO system to
which print jobs that are destined for a printer
attached to the OkiLAN 6020e will be directed.
• OKIPRINTER - The host name of the remote
system which is the OkiLAN 6020e. For example,
to telnet to the OkiLAN 6020e and invoke the
OkiLAN 6020e Configuration utility, you would
type telnet OKIPRINTER. A host name is not
required for the OkiLAN 6020e, the IP address
may be used.
• yourqueuename - This is the name of the queue
on the OkiLAN 6020e and must end with 1, 2, 3
or 4 depending on the port selected to service the
print jobs.
If FF, LF or NF are the last two letters of the
queue name, the job will be converted
accordingly. See pages IV-15 and IV-16 for more
information on remote queue names.
Before you proceed, verify that the following
prerequisites are met:
1. SCO TCP/IP version 1.2 or later must be installed.
2. The name of the OkiLAN 6020e (OKIPRINTER)
and the IP address you wish to assign are in the
“/etc/hosts” file of the SCO machine.
3. The IP address of the OkiLAN 6020e has been
assigned and you are able to telnet to OKIPRINTER
successfully.
OKI OkiLAN 6020e User’s Guide
IV - 73
TCP/IP
Prerequisites
Section 4 - Appendix B - Application Considerations
Procedure
1. Login to the SCO machine as root.
2. Install Remote Line Printing or verify that it is
running by typing mkdev rlp at the UNIX prompt. It
will respond by asking if you want to install or
remove remote line printing. Choose Install even if
remote line printing may already be installed.
3. If remote line printing is already installed, mkdev
rlp will respond with the message Remote line
printing working directory already exists. Do you
wish to continue installing the remote line printing
system? Answer no to this prompt and skip to Step 6.
If remote line printing was not installed, mkdev rlp
will respond with messages detailing files and
directories that it is creating.
4. The command mkdev rlp will ask if you wish to
change the printer description file “/etc/printcap”.
Choose no for this prompt. It will respond saying
Run ‘/etc/rlpconf’ to change the remote printer
description file. Do NOT run “/etc/rlpconf”. We will
be performing the functions of “/etc/rlpconf”
manually.
5. The next prompt is Do you want to start remote
daemon now? Answer yes to this prompt. This
should bring you back to the UNIX prompt.
6. Using a text editor (such as vi), add the following
entry to the “/etc/printcap” file”
lj4:\
:lp=:rm=OKIPRINTER:rp=pcl2:\
:sd=/usr/spool/lpd/lj4:\
:lf=/usr/spool/lpd/lj4/lj4.log:
7. At the UNIX prompt, type:
mkdir /usr/spool/lpd/lj4.
8. Type:
touch/usr/spool/lpd/lj4/lj4.log
9. Try printing to the OkiLAN 6020e by issuing the
following command:
lp -d lj4 filename
IV - 74
OKI OkiLAN 6020e User’s Guide
Section 4 - Appendix B - Application Considerations
IBM’s AIX ver. 3.x for Printing with the
OkiLAN 6020e
This application note describes the configuration of the
printing system on IBM’s AIX version 3.x of the UNIX
operating system. The following specific names will be
used to represent general devices or concepts.
• lj4 - The local queue name on the AIX system to
which print jobs that are destined for a printer
attached to the OkiLAN 6020e will be directed.
• OKIPRINTER - The host name of the remote
system which is the OkiLAN 6020e. For example,
to telnet to the OkiLAN 6020e and invoke the
OkiLAN 6020e Configuration utility, you would
type telnet OKIPRINTER. A host name is not
required for the OkiLAN 6020e, the IP Address
may be used.
• yourqueuename - This is the name of the queue
on the OkiLAN 6020e and must end with 1 or 2,
depending on the port selected to service the print
jobs.
If FF, LF or NF are the last two letters of the
queue name, the job will be converted
accordingly. See pages IV-15 and IV-16 for more
information on remote queue names.
Before you proceed, the name OKIPRINTER and the
IP address assigned to the OkiLAN 6020e should be in
the “/etc/hosts” file on the AIX system.
Procedure
To configure the AIX machine so that users can spool
print jobs to the pcl2 print queue on the OkiLAN 6020e
named OKIPRINTER, do the following:
1. Login to the AIX machine as root.
2. Invoke the SMIT utility by typing:
AIX> smit <enter>
OKI OkiLAN 6020e User’s Guide
IV - 75
TCP/IP
Prerequisites
Section 4 - Appendix B - Application Considerations
3. To add a remote queue, select the following options
from the SMIT menu:
Spooler (Print Jobs and Printers)
Manage Remote Printer Subsystem
Client Services
Remote Printer Queues
Add a Remote Queue
A form appears asking you to define a remote print
queue.
4. Enter information into the following fields as
described. All other fields should use the default
value.
a) NAME of queue to add - lj4
This is the name of the local print queue.
b) DESIGNATION HOST for remote jobs OKIPRINTER
This is the name of the OkiLAN 6020e. This host
name must also be contained in the “/etc/hosts”
file.
c) Name of QUEUE on remote printer yourqueuename
d) NAME of device to add - “any arbitrary name”
This is a device name required by AIX, but this
name has no effect on the print service for the
OkiLAN 6020e. Enter any name of seven
characters or less. The name does not need to be
an existing device, nor does it need to be unique.
5. Start the lpd subsystem with SMIT:
Spooler (Print Jobs and Printers)
Manage Remote Printer Subsystem
Server Services
lpd Remote Printer Subsystem
Start Using the lpd Subsystem
Start BOTH Now and at System Restart
IV - 76
OKI OkiLAN 6020e User’s Guide
Section 4 - Appendix B - Application Considerations
6. Start the qdaemon by typing:
AIX> startsrc -s qdaemon
7. Try printing to the printer attached to the OkiLAN
6020e by issuing the following command:
AIX> lpr -Plj4 filename
This application note describes the configuration of the
printing system on the Solaris ver. 2.x UNIX operating
system. For clarity and brevity, the following specific
names will be used to represent general devices or
concepts.
• lj4 - The local queue name on the Solaris system
to which print jobs that are destined for a printer
attached to the OkiLAN 6020e will be directed.
• OKIPRINTER - The host name of the remote
system which is the OkiLAN 6020e. For example,
to telnet to the OkiLAN 6020e and invoke the
OkiLAN 6020e Configuration utility, you would
type telnet OKIPRINTER. A host name is not
required for the OkiLAN 6020e, the IP Address
may be used.
• yourqueuename - This is the name of the queue
on the OkiLAN 6020e and must end with 1, 2, 3
or 4, depending on the port selected to service the
print jobs.
If FF, LF or NF are the last two letters of the
queue name, the job will be converted
accordingly. See pages IV-15 and IV-16 for more
information on remote queue names.
OKI OkiLAN 6020e User’s Guide
IV - 77
TCP/IP
Configuring Solaris 2.x for Printing
with the OkiLAN 6020e
Section 4 - Appendix B - Application Considerations
Prerequisites
Before you proceed, the following prerequisites must
be met:
1. The name OKIPRINTER and the IP address
assigned to the OkiLAN 6020e are in the
“/etc/hosts” file on the Solaris system.
2. Make sure the LPD daemon is running on the Solaris
system.
Procedure
To configure the Solaris machine so users can spool
print jobs to the pcl print queue on the OkiLAN 6020e
named OKIPRINTER, do the following:
1. Login to the Solaris machine as root.
2. Type: lpsystem -t bsd OKIPRINTER.
3. Type: lpadmin -p lj4 -s
OKIPRINTER!yourqueuename - I any.
4. Type: accept lj4.
5. Type: enable lj4.
6. Try printing by issuing the following command:
lp -d lj4 filename
IV - 78
OKI OkiLAN 6020e User’s Guide
Section 4 - Appendix B - Application Considerations
This application note describes the configuration of the
printing system on the Sun-OS ver 4.1.x and Ultrix ver.
4.2 of the UNIX operating system. For clarity and
brevity, the following specific names will be used to
represent general devices or concepts.
• lj4 - The local queue name on the Sun-OS or
Ultrix system to which print jobs that are destined
for a printer attached to the OkiLAN 6020e will
be directed.
• OKIPRINTER - The host name of the remote
system which is the OkiLAN 6020e. For example,
to telnet to the OkiLAN 6020e and invoke the
OkiLAN 6020e Configuration utility, you would
type telnet OKIPRINTER. A host name is not
required for the OkiLAN 6020e, the IP Address
may be used.
• yourqueuename - This is the name of the queue
on the OkiLAN 6020e and must end with 1, 2, 3
or 4, depending on the port selected to service the
print jobs.
If FF, LF or NF are the last two letters of the
queue name, the job will be converted
accordingly. See pages IV-15 and IV-16 for more
information on remote queue names.
Prerequisites
Before you proceed, the following prerequisites must
be met:
1. The name OKIPRINTER and the IP address
assigned to the OkiLAN 6020e are in the
“/etc/hosts” file on the Sun-OS or Ultrix system.
2. Make sure the LPD daemon is running on the SunOS or Ultrix system by issuing the following
command at the UNIX prompt:
ps aux | grep lpd
OKI OkiLAN 6020e User’s Guide
IV - 79
TCP/IP
Configuring Sun-OS v4.1.x or Ultrix
v4.2 for Printing with the OkiLAN
6020e
Section 4 - Appendix B - Application Considerations
If the LPD daemon is running, you should see output
similar to:
root 135 0.0 0.0 52 0 ? IW May 24 0:01
/usr/lib/lpd
If the LPD daemon is not running, start the daemon
by logging into the Sun-OS or Ultrix machine as root
and issuing the following command at the UNIX
prompt:
/usr/lib/lpd
Verify that the daemon is running by using the ps
command described previously.
To start the LPD daemon automatically when the
system boots, make sure that lines similar to the
following exist in the “/etc/rc” file:
if [ -f /usr/lib/lpd ] ; then
rm -f /dev/printer/var/spool/lpd.lock
/usr/lib/lpd; echo -n ‘ printer’
fi
Procedure
To configure the Sun-OS or Ultrix machine so that
users can spool print jobs to the pcl print queue on the
OkiLAN 6020e named OKIPRINTER, do the
following:
1. Login to the Sun-OS or Ultrix machine as root.
2. Using a text editor (such as vi), add this entry to the
“/etc/printcap” file:
lj4:\
:lp=:rm=OKIPRINTER:rp=yourqueuename:\
:sd=/usr/spool/lj4:\
:lf=/usr/spool/lj4/lj4.log
3. At the UNIX prompt, type: mkdir /usr/spool/lj4.
4. Type: touch /usr/spool/lj4/lj4.log.
5. Try printing by issuing the following command:
lpr -Plj4 filename
IV - 80
OKI OkiLAN 6020e User’s Guide
Section 4 - Appendix C - Internet Printing Protocol (IPP)
Appendix C
Internet Printing Protocol (IPP)
Internet Printing Protocol (IPP) is an application level
protocol that can be used for distributed printing over
the Internet. Using the new IPP protocol from any
standard IPP client, you can print to any printer that is
connected both to your OkiLAN 6020e and to the
Internet.
With the OkiLAN 6020e, there is no configuration
required. Enter the print server IPP URL as
http://xxx.xxx.xxx.xxx:631/ipp/portn, where
xxx.xxx.xxx.xxx is the IP address of the print server
and portn is the output port number.
Example: http://198.60.248.120:631/ipp/port2.
TCP/IP
Since IPP is a new industry standard, users are advised
to check with the vendors of their operating systems for
IPP client and IPP server software. Examples are
Novell, Microsoft and EASYSOFTWARE for a generic
version of a UNIX® CUPS® driver that supports the
IPP protocol.
OKI OkiLAN 6020e User’s Guide
IV - 81
Section 4 - Appendix C - Internet Printing Protocol (IPP)
IV - 82
OKI OkiLAN 6020e User’s Guide
Section V:
LAN Manager/ Server
LAN Manager/LAN
Server
Section 5 - LAN Manager/LAN Server
In This Section
Chapter 1 Introduction ........................................... V-3
Overview ....................................................... V-3
System Requirements .................................... V-3
Chapter 2 Installation ............................................. V-5
Overview ....................................................... V-5
Network Preparation ...................................... V-5
Installing the Utilities Software ..................... V-6
Running INSTALL ........................................ V-7
Running OkiNet for OS/2 .............................. V-7
Creating an OS/2 Printer ................................ V-9
Printing a Configuration Sheet .................... V-10
Chapter 3 Printing in the OS/2 Environment ..... V-11
Overview ..................................................... V-11
OS/2 1.3 ....................................................... V-11
OS/2 2.X and OS/2 Warp ............................. V-11
DOS and WIN-OS/2 .................................... V-12
Chapter 4 Additional Utility Features ................. V-13
Overview ..................................................... V-13
Deleting a Local Port ................................... V-13
Configuring a Print Server ........................... V-13
Configuring Parallel Port P1 ........................ V-14
Restoring Factory Defaults .......................... V-15
Printing a Configuration Sheet .................... V-15
Chapter 5 Using HELP ......................................... V-16
Overview ..................................................... V-16
General Help ................................................ V-16
Context-Sensitive Help ................................ V-16
Appendix A Troubleshooting .............................. V-17
No Configuration Sheet ............................... V-17
Unable to Print ............................................. V-17
V-2
OKI OkiLAN 6020e User’s Guide
Section 5 - Chapter 1 - Introduction
Chapter 1
Introduction
Overview
This section contains information about the OkiNet for
OS/2 utility. This utility allows you to install and
configure the OkiLAN 6020e for your specific
environment. The utility provides configuration
information and allows you to print a configuration
sheet.
System Requirements
Please note the following system requirements:
Supported Environments
The OkiLAN 6020e is supported in the following
operating environments:
• OS/2 version 1.3 with LAN Manager version 2.X
• OS/2 version 1.3 through 2.X with LAN Server
version 2.X and 3.X
• OS/2 Warp 3.0 with LAN Server version 4.X
CSD Levels
IBM provides maintenance upgrades to OS/2 in the
form of Corrective Service Diskettes (CSDs). We
strongly recommend that you use the most recent CSDs
available, because the CSDs include fixes to the OS/2
print subsystem. Contact IBM at 800-342-6672 for
information about recent CSDs.
A printer connected to the network can be accessed
from DOS and other network nodes properly
configured as LAN Manager/LAN Server client nodes.
You should be familiar with the OS/2 Print
Management utilities. See your OS/2 manuals for more
information.
OKI OkiLAN 6020e User’s Guide
V-3
LAN Manager/ Server
Client Nodes
Section 5 - Chapter 1 - Introduction
DLC/802.2 Protocol Stack
The DLC/802.2 protocol stack must be loaded and
running on the file server from which the OKI Network
Printer Redirector will run. With LAN Manager, this
means you must enable the remote boot facility. With
LAN Server, you must select the 802.2 protocol when
you run the installation utility. See your LAN Manager/
LAN Server documentation for more information.
Routers
The 802.2 Type I network protocol used by the OKI
Network Printer Redirector cannot be routed by routers
which operate on specific protocols at the network
layer. See your router documentation for more
information.
V-4
OKI OkiLAN 6020e User’s Guide
Section 5 - Chapter 2 - Installation
Chapter 2
Installation
Overview
To install the OkiLAN 6020e:
1. Install the OkiNet for OS/2 utilities software.
2. Run the OkiNet for OS/2 utility to add a local printer
port.
3. Associate a print queue with the new local printer
port.
Once the installation is complete, you can verify
communication by printing a configuration sheet.
• You must have network administrator privileges to
install the OkiLAN 6020e.
• You must have physical access to an OS/2 file server
to host the OKI software utilities.
• Write down the serial number and the Ethernet
address of your OkiLAN 6020e.
• OS/2 and LAN Manager/LAN Server must be
configured with the following protocol:
DLC/802.2 protocol stack
• LAN Manager users must enable the remote boot
facility.
• LAN Server 2.X users must run the LAN Server
installation utility and select the 802.2 protocol.
• LAN Server 3.0 users must run the LAPS utility and
select the 802.2 protocol.
• OS/2 Warp Users must run the MPTS utility and
select the 80w.w protocol. See your network
administrator or the LAN Manager/LAN Server
manuals for instructions.
OKI OkiLAN 6020e User’s Guide
V-5
LAN Manager/ Server
Network Preparation
Section 5 - Chapter 2 - Installation
• The initial installation requires the file server to be
brought down and then back up again. This may be a
consideration when you are planning your install.
Depending on your current configuration, the following
software may also be needed:
• Printer driver installation diskettes. These diskettes
are provided with the OS/2 operating system or are
available from the printer manufacturer.
• LAN Manager or LAN Server installation diskettes.
Note: It is strongly recommended that you make
backup copies of the OS2.INI and
OS2SYS.INI files before you install the
OkiLAN 6020e. Follow the directions in your
OS/2 documentation to back up these files.
Installing the Utilities Software
Two software utilities are provided with the OkiLAN
6020e: INSTALL and OkiNet for OS/2.
Install
The INSTALL utility copies both software utilities to
your OS/2 server and registers the OKI application with
the OS2.INI file. You will need to run INSTALL one
time only.
OkiNet for OS/2
The OkiNet for OS/2 utility completes the initial
installation of the OkiLAN 6020e. In addition, you can
run the utility as needed to modify the configuration of
the OkiLAN 6020e or to view port information.
Note: The directory where OKI DLL files install,
c:\OS2\DLL, must be the first entry in the
LIBPATH command located in the
CONFIG.SYS file. When you reboot the
system, the OS/2 spooler will load the OKI
Network Printer Redirector.
V-6
OKI OkiLAN 6020e User’s Guide
Section 5 - Chapter 2 - Installation
Running INSTALL
1. Login to the server with administrator privileges.
If you are reinstalling the utility, disable the spooler
before running install. If this is the first time you
have installed the utility, disabling the spooler is
optional.
2. From the OS/2 command line, change to the OS/2
directory.
3. Check the README file for current installation
notes.
4. Type INSTALL and press Enter.
5. Verify the install directories are correct.
6. Select INSTALL to proceed. When the utilities are
installed, you will see a message indicating that the
installation was successful.
If the install was not successful read through the
comments in the Install Progress window for errors
and recommended action.
7. Select Exit.
Completing the Installation
After the OKI software has been installed, you must do
the following:
1. Verify the OS/2 spooler is enabled.
2. Verify /OS2/DLL is first in the LIBPATH statement
in the CONFIG.SYS file.
3. Shut down and restart the OS/2 file server.
4. Run the OkiNet for OS/2 utility to add local ports.
Before you can print via the OkiLAN 6020e, you must
first add a local printer port to your OS/2 server.
1. Select the Network Printing Tools folder on the
OS/2 desktop or in the Desktop Manager.
2. Select the OkiNet for OS/2 utility icon.
OKI OkiLAN 6020e User’s Guide
V-7
LAN Manager/ Server
Running OkiNet for OS/2
Section 5 - Chapter 2 - Installation
3. Select OK. The ESI Print Server Status Screen will
display. From the Configure menu, select Add Local
Port.
4. Select a print server and port.
Print servers are identified by serial number. (You
will find the serial number for your OkiLAN 6020e
on the enclosure.) The port is indicated by P1, P2,
P3, or P4. Use the arrow buttons to scroll through
the available print servers on the network.
5. Enter a local port name. Highlight the entry field
labeled Local Port Name, and enter a name that will
help you identify the local printer port.
The name must begin with “\PIPE\”, which is
provided by default. It can be up to eight characters
long (excluding “\PIPE\”) and must follow OS/2 file
naming conventions.
6. Select Add. Selecting Cancel exits without adding a
local printer port.
7. Repeat these steps for all print server ports you are
configuring.
8. Exit OkiNet for OS/2.
V-8
OKI OkiLAN 6020e User’s Guide
Section 5 - Chapter 2 - Installation
Creating an OS/2 Printer
To print to the local port created by OkiNet for OS/2,
you must create an OS/2 printer.
OS/2 1.3
1. Open the Print Manager from the desktop.
2. Select SETUP from the menu.
3. Select Printers. This will display a list of printers
currently configured on this server.
4. Select Add. A dialog box will display, defining the
configuration for a new printer.
5. Configure the printer as you would configure a
directly-attached printer. Set the device field to the
local port name you created in OkiNet for
OS/2.
Use the Print Manager to attach queues to the
printer you just created. Refer to your OS/2
documentation for more information on these
operations.
OS/2 2.X and OS/2 Warp
OKI OkiLAN 6020e User’s Guide
V-9
LAN Manager/ Server
1. Drag a printer object from the templates folder to the
desktop on the server. This action will display a
configuration window.
2. Enter the name of the printer, the default printer
driver and the output port. For the Output Port, select
the icon for the local port name you created in
OkiNet for OS/2.
For more information on these operations, refer
to your OS/2 documentation.
Section 5 - Chapter 2 - Installation
Printing a Configuration Sheet
You can verify communication by printing a
configuration sheet using OkiNet for OS/2.
1. Select Configure from the main Print Server
window.
2. Select Configure Print Server.
3. Select the OkiLAN 6020e you would like to test.
4. From the options, select Print Configuration Sheet.
5. Click the Configure button.
Note: In order for the configuration sheet to print
correctly, the OkiLAN 6020e must determine if
the connected printer is a text, PCL, or
PostScript printer. The default is text. If the
connected printer is a PostScript-only printer,
you will have to reconfigure the OkiLAN
6020e to print the configuration sheet in
PostScript. The configuration sheet will print to
all connected printers.
A configuration sheet will print automatically if the
OkiLAN 6020e fails due to a network protocol error.
V - 10
OKI OkiLAN 6020e User’s Guide
Section 5 - Chapter 3 - Printing in the OS2 Environment
Chapter 3
Printing in the OS/2
Environment
Overview
OS/2 provides several methods for selecting a printer
from within an application. The best method to use
depends on the specific application. The following
methods are provided as simple examples for different
environments within OS/2.
Note: The following examples will work on any OS/2
machine on the network, provided that the
proper network privileges and protocols have
been observed.
OS/2 1.3
To specify a queue as the default for your system, do
the following:
1. Select Print Manager.
2. Select SETUP.
3. Select Application Defaults.
4. Change the default print queue to the print queue
associated with the OkiLAN 6020e.
OS/2 Presentation Manager applications which use the
default printer will now print to the OkiLAN 6020e
printer.
To specify the printer attached to the OkiLAN 6020e as
the OS/2 default printer, do the following:
1. From the desktop, right-click on any printer icon.
2. Select the right arrow next to Set Default. A list of
print queues defined for your system will display.
OKI OkiLAN 6020e User’s Guide
V - 11
LAN Manager/ Server
OS/2 2.X and OS/2 Warp
Section 5 - Chapter 3 - Printing in the OS2 Environment
3. Select the print queue associated with the OkiLAN
6020e.
OS/2 applications that use the default printer will
now print to the printer attached to the OkiLAN
6020e.
The OS/2 print screen function uses the OS/2 default
printer. This function is invoked when you press the
Print Screen key while on the desktop, in an OS/2
window, or when you are running an OS/2
application.
4. Press Print Screen on your keyboard. A copy of
your screen will appear on the appropriate printer.
DOS and WIN-OS/2
DOS and WIN-OS/2 do not observe the OS/2
Presentation Manager default printer setting. Both DOS
and WIN-OS/2 applications typically use LPT1 as the
default printer. To use the newly defined print queue as
a DOS or WIN-OS/2 printer, you must assign a DOS or
WIN-OS/2 device name to the desired queue.
Example:
If the OkiLAN 6020e is installed on a server
named SERVER 1 and assigned the queue name
MPXLPT, the following command issued from an
OS/2 command prompt would reassign LPT1:
C>NET USE LPT1 \\Server1\MPXLPT
If OS/2 does not recognize the network name,
enter the following command from an OS/2
prompt on the server where the software utilities
were installed:
C>NET SHARE MPXLPT /PRINT
Any applications using LPT1 will now print to the
OkiLAN 6020e.
V - 12
OKI OkiLAN 6020e User’s Guide
Section 5 - Chapter 4 - Additional Utility Features
Chapter 4
Additional Utility Features
Overview
You can run the OkiNet for OS/2 utility at any time to
access the following optional features:
• Deleting a Local Port
• Configuring a Print Server
Deleting a Local Port
The delete command allows you to delete a local port
that has been previously added.
1. Verify the local port is not attached to an OS/2
printer queue. The local port cannot be deleted if it is
attached to an OS/2 printer queue.
2. Login to the server with administrator privileges and
run OkiNet for OS/2.
3. Click OK.
4. From the Configure menu, select Delete Local Port.
5. From the Delete Local Port screen, use the scroll
arrows to select and highlight the local port you wish
to delete.
6. Select Delete. The Cancel button exits the screen
without deleting the port.
To add additional local ports, follow the Running
OkiNet for OS/2 instructions on page VI-8.
OkiNet for OS/2 allows you to change the default
configuration of the OkiLAN 6020e. These
configuration settings are retained when the OkiLAN
6020e is powered off.
1. Login to the server with administrator privileges and
run OkiNet for OS/2.
2. Click OK.
OKI OkiLAN 6020e User’s Guide
V - 13
LAN Manager/ Server
Configuring a Print Server
Section 5 - Chapter 4 - Additional Utility Features
3. From the Configure menu, select Configure Print
Server. The following screen will display:
The OkiLAN 6020e will reset by selecting OK to save
any of the options, except the Print Configuration
Sheet option.
Configuring Parallel Port P1
Ports P1 must be configured based on the printer you
intend to use.
1. From the Configure Print Server window, choose a
print server from the list at left.
2. Select Parallel Port-P1 from the list at right and
then click the Configure button.
3. Click OK when you have selected the appropriate
settings. The configuration settings will be stored in
the OkiLAN 6020e and will be retained even when
the OkiLAN 6020e is powered off.
CAUTION: If you change the configuration while a
job is printing, the job may not print successfully.
Configuration option for parallel Port P1 and P2:
• Configuration page print language - The factory
default is TEXT. If your OkiLAN 6020e is attached
to a PostScript or PCL printer, enable the appropriate
selection. The OkiLAN 6020e configuration sheet
will be printed in the language you select. This
setting only affects the configuration sheet, not other
print jobs.
V - 14
OKI OkiLAN 6020e User’s Guide
Section 5 - Chapter 4 - Additional Utility Features
Restoring Factory Defaults
The Restore Defaults option restores the factory default
settings for the LAN Manager/LAN Server protocol
and output ports. To restore factory defaults, select an
OkiLAN 6020e from the list on the left. Then select
Restore Factory Defaults from the list on the right.
Click the Configure button.
CAUTION: If you restore the factory default settings
while a job is printing, the job may not print
successfully.
Printing a Configuration Sheet
To print a configuration sheet, select an OkiLAN 6020e
from the print server list on the left. Then select Print
Configuration Sheet from the list on the right. Click
the Configure button. A configuration sheet will print
to each printer.
Note: In order for the configuration sheet to print
correctly, the OkiLAN 6020e must determine if
the connected printer is a text, PCL, or
PostScript printer. The default is TEXT. If the
connected printer is a PostScript-only printer,
you must configure the OkiLAN 6020e to print
the configuration sheet in PostScript.
OKI OkiLAN 6020e User’s Guide
V - 15
LAN Manager/ Server
The configuration sheet will print automatically if the
OkiLAN 6020e fails due to a network protocol error.
Section 5 - Chapter 5 - Using HELP
Chapter 5
Using Help
Overview
The OkiNet for OS/2 utility provides both general and
context-specific help.
General Help
To access help information about installation and
configuration, select Help from the main menu, then
select General Help.
To access help information about a specific topic, select
Help from the main menu, then select Help Index.
See your OS/2 manual form information on using online help.
Context-Sensitive Help
Context-sensitive help is available from many areas of
OkiNet for OS/2.
Several of the configuration windows have help buttons
which, when selected, provide information about that
specific window.
V - 16
OKI OkiLAN 6020e User’s Guide
Section 5 - Appendix A - Troubleshooting
Appendix A
Troubleshooting
No Configuration Sheet
If the LED turns solid orange due to a network protocol
error and no configuration sheet is printed, your printer
may be configured for PostScript operation. If so, you
must re-configure your printer for standard ASCII text
mode so that the configuration sheet can be printed. See
you printer manuals for more information.
Unable to Print
OKI OkiLAN 6020e User’s Guide
V - 17
LAN Manager/ Server
If the OkiLAN 6020e passes self-test, but you are
unable to send data to the printer via the OkiLAN
6020e, you may want to check the following:
• Printer configuration
• Printer hardware
• Computer network adapter cards
• Cabling and/or connectors application software
configuration
• Cable adapters
• OkiLAN 6020e port configuration
EtherTalk
Section VI:
EtherTalk Support for
Apple® MacIntosh®
Section 6 - EtherTalk
In This Section
Chapter 1 Introduction .......................................... VI-3
Overview ...................................................... VI-3
System Requirements ................................... VI-3
Before You Start ...........................................VI-3
Chapter 2 The OkiLAN 6020e Utility .................... VI-4
Overview ...................................................... VI-4
Running the OkiLAN 6020e Utility ............. VI-4
Finding the OkiLAN 6020e ..........................VI-4
Renaming the OkiLAN 6020e Printer .......... VI-5
Selecting a Zone ...........................................VI-5
Print Configuration ....................................... VI-6
Status .............................................................VI-6
Advanced Configuration Options ................. VI-6
Appendix A Troubleshooting ............................... VI-8
Before You Call ............................................VI-8
OkiLAN 6020e Does Not Appear in the
Macintosh Chooser .................................... VI-8
Unable to Print from a Macintosh ................ VI-9
Unable to Print a Document ......................... VI-9
Network Error Messages ............................ VI-10
OkiLAN 6020e Utility ................................VI-10
OkiLAN 6020e Utility Errors ..................... VI-11
Appendix B Selecting Your Printer .................... VI-13
Appendix C Capturing With a Spooler .............. VI-14
Overview .................................................... VI-14
Capturing Without Bypass ..........................VI-14
Capturing With Bypass ...............................VI-15
VI - 2
OKI OkiLAN 6020e User’s Guide
EtherTalk
Section 6 - Chapter 1 - Introduction
Chapter 1
Introduction
Overview
This section describes the steps necessary to configure
the EtherTalk protocol. The following topics are
covered in this section:
• Setting the Printer Name
• Selecting a Zone
• Selecting the Printer from the Macintosh Chooser
• Print Configuration and Status Information
• Advanced Configuration
System Requirements
Please note the following system requirements:
• PostScript Level 2 must be available on your printer
• The network must be a Phase 2 EtherTalk network
• Your printer must have a bidirectional parallel port
(IEEE-1284 standard)
Ethertalk is only available on the parallel port..
Before You Start
1. Install the OkiLAN 6020e hardware and connect the
cabling. Instructions for hardware installation are
found in Section I of this manual.
2. Write down the serial number and Ethernet address
of the OkiLAN 6020e.
3. Copy the files from the CD-ROM to a utilities folder
on the Macintosh hard drive.
4. Consult your network administrator before using the
OkiLAN 6020e utility. Changing the OkiLAN 6020e
Name or Zone may require users to reselect the
OkiLAN 6020e in the Chooser. Print servers and
spoolers may also need to be reconfigured after the
OkiLAN 6020e product’s configuration has been
changed.
OKI OkiLAN 6020e User’s Guide
VI - 3
Section 6 - Chapter 2 - The OkiLAN 6020e Utility
Chapter 2
The OkiLAN 6020e Utility
Overview
The OkiLAN 6020e utility allows the user to:
• Change the OkiLAN 6020e product’s AppleTalk
Name
• Move the OkiLAN 6020e from the Default Zone to a
Preferred Zone
• Print Configuration Page and view Status
Information
• Use Advanced Configuration Options
Running the OkiLAN 6020e Utility
1. Turn on your printer and check that it is on-line.
Verify the parallel cables are directly connected
between the OkiLAN 6020e and the printer.
2. Turn on the OkiLAN 6020e. The status LED should
turn solid green.
3. Copy the files from the diskette labeled OKI
EtherTalk Utilities to a utilities folder on the
Macintosh hard drive.
4. Run the OkiLAN 6020e utility by double-clicking
the OkiLAN 6020e utility icon.
Finding the OkiLAN 6020e
The Zone Selection window (shown on the previous
page) will contain a list of zones available on the
network. If no router is found, an asterisk “*” will
display. To locate OkiLAN 6020e devices on the
network:
1. Select a zone to search for OkiLAN 6020e printers.
Shift-click to select multiple zones or click Select
All to select all available zones.
2. Select Search to search the network for OkiLAN
6020e printers in the selected zones or select Quit to
exit the utility.
VI - 4
OKI OkiLAN 6020e User’s Guide
Renaming the OkiLAN 6020e Printer
The OkiLAN 6020e Printer Selection window contains
a list of all OkiLAN 6020e printers found in the
selected zones. OkiLAN 6020e printers are listed
alphabetically by name. Each port of a multiport
OkiLAN 6020e will appear separately in the list.
Unless otherwise stated, changing a configuration
option will affect only the selected port.
1. Choose the OkiLAN 6020e printer you wish to
rename.
2. Select Name from the Configure pull-down menu.
3. Enter a name for the OkiLAN 6020e. If you choose
a name that is already being used, the OkiLAN
6020e will append a number to the end of the name.
Names can be a maximum of 32 characters long.
4. Click Rename. You will then be returned to the
Printer Selection window.
Note: The options listed on the following pages can
all be accessed from the Printer Selection
window.
Selecting a Zone
1. Choose the OkiLAN 6020e printer you wish to
rezone.
2. Select Zone from the Configure pull-down menu.
3. Choose the zone in which you want the printer to
appear.
Note: If no Phase 2 router was found, this option will
be unavailable.
4. Click OK.
OKI OkiLAN 6020e User’s Guide
VI - 5
EtherTalk
Section 6 - Chapter 2 - The OkiLAN 6020e Utility
Section 6 - Chapter 2 - The OkiLAN 6020e Utility
Print Configuration
The Print Configuration option is accessed by selecting
Print Config from the File pull-down menu. Choose
this option to print an OkiLAN 6020e configuration
sheet. A configuration sheet will print to all output
ports.
Status
The Status option is accessed by selecting Status from
the File pull-down menu. This option displays the
status and EtherTalk configuration of the selected
OkiLAN 6020e printer.
Advanced Configuration Options
The following configuration options are advanced
features of the OkiLAN 6020e utility. Most users will
not need to access these features. Read the folloiwng
descriptions carefully before utilizing these options.
Set Type
The Set Type option is accessed by selecting Type from
the Configure pull-down menu. This option allows you
to configure the AppleTalk Type. For some print
spoolers to work properly, the AppleTalk Type must be
changed. Refer to Appendix C of this section for more
information.
The default AppleTalk Type is LaserWriter. For most
printer drivers, this setting should not be changed. This
includes the LaserWriter Drivers, HP LaserJet Drivers
and other drivers.
Each EtherTalk printer port supports two AppleTalk
Types:
• Type1 (mandatory) - The Type 1 default is
LaserWriter. This option should not be changed
unless the user wishes to use a print spooler without
bypass or the user does not want the printer to
respond to any of the LaserWriter drivers.
• Type 2 (optional) - Select this option when
configuring for a spooler.
VI - 6
OKI OkiLAN 6020e User’s Guide
Enable Port
This option allows you to enable or disable a port. If a
port is disabled, it will appear in the OkiLAN 6020e
utility but will not appear in the Chooser. A disabled
port cannot be configured. The only valid options for a
disabled port are Status, Enable Port, Print Config, and
Restore Defaults. A port should be disabled when no
printer is attached.
Note: It is possible to disable all ports but this is not
recommended. The EtherTalk protocol will still
be active on the network. To disable the
EtherTalk protocol, use a utility from one of the
other protocols.
Reset Board
This option will reset the print server.
Restore Defaults
This option will automatically return the EtherTalk
interface to its factory defaults. All ports will be
restored to factory defaults.
The following OkiLAN 6020e variables will restore to
default:
Name: OKI <serial number> Port <port number>
(for single port products, the port number will not
be shown)
Type 1 = LaserWriter
Type 2 = (None)
Zone = Default - (The default zone for the network
segment will be used)
Port Enabled = Yes
OKI OkiLAN 6020e User’s Guide
VI - 7
EtherTalk
Section 6 - Chapter 2 - The OkiLAN 6020e Utility
Section 6 - Appendix A - Troubleshooting
Appendix A
Troubleshooting
Before You Call
This appendix allows you to troubleshoot problems you
may have installing or using the EtherTalk protocol.
After trying these suggestions, if you are still having
difficulty, call Oki Data Customer Support at 1-800OKI-DATA (1-800-654-3282).
If you have trouble sending data to the printer through
your OkiLAN 6020e, check the following:
• Verify that the OkiLAN 6020e printer appears in the
Chooser
• Printer configuration
• Printer hardware
• OkiLAN 6020e configuration
• OkiLAN 6020e hardware
• Cabling and/or connectors
• Macintosh System version
• LaserWriter driver version
• Application software configuration
OkiLAN 6020e Does Not Appear in the
Macintosh Chooser
If the OkiLAN 6020e does not appear in the Chooser as
a LaserWriter device, check the following:
• Print a configuration sheet. Verify that the EtherTalk
protocol and port are enabled.
• Verify that the AppleTalk type is LaserWriter.
• Verify that the OkiLAN 6020e has passed self-test.
The status indicator should be solid green.
• Check the connections between the OkiLAN 6020e
and the Macintosh. When the OkiLAN 6020e does
not appear in the Chooser, it is often caused by a
cabling problem.
• Verify EtherTalk Phase 2 is selected in the Control
Panel.
VI - 8
OKI OkiLAN 6020e User’s Guide
Unable to Print from a Macintosh
If you are unable to print from a Macintosh via the
OkiLAN 6020e, try the following:
• Verify the OkiLAN 6020e appears in the Chooser as
a LaserWriter device. If the OkiLAN 6020e does
appear in the Chooser, make certain it is selected.
• Make sure you are using System and Finder version
6.02 or later and LaserWriter driver version 8.0 or
later.
• Verify the printer supports PostScript Level 2 via the
printer test/ configuration sheet.
• If the status message Printer Error: Bi-Di
communication on printer’s parallel port is not
enabled appears, verify your printer’s parallel port is
a bidirectional port and is enabled.
• Print an OkiLAN 6020e configuration sheet to verify
language switch settings. Verify the setting is NOT
PCL.
• Verify the printer’s language setting is NOT PCL.
Unable to Print a Document
If a document will not print, first check your printer.
Look for paper jams, an empty paper tray, low toner
error or other error conditions. Try to print the
document again. If it still does not print, exit the
application and try a Desktop Print from the File menu.
If the directory prints correctly, re-enter the application
and try to print a different document. If the second
document prints successfully, your problem may be
document-specific. Check for problems in the
document. If your printer has error handling capability,
activate the error handler and try to print the first
document again to obtain an error report.
OKI OkiLAN 6020e User’s Guide
VI - 9
EtherTalk
Section 6 - Appendix A - Troubleshooting
Section 6 - Appendix A - Troubleshooting
If the directory does not print, send the directory again,
and watch the OkiLAN 6020e activity indicator. If the
status indicator flashes to indicate activity, data is
reaching the OkiLAN 6020e. Send the document again
and watch the printer for activity. If you see activity but
no output, data is reaching the printer, but the printer is
aborting the job. A PostScript printer will flush its
memory buffer whenever it encounters an error
condition, thereby aborting the entire job.
Try the following:
• Power the printer and the OkiLAN 6020e off and on.
Allow the OkiLAN 6020e and the printer to warm
up before you send a print job.
• Verify the printer is on-line and ready.
• Verify the OkiLAN 6020e is configured correctly.
• If you suspect any of the cables are bad, swap them
with cables you know are working.
Network Error Messages
Network range exceeded during router power up—
There are too many nodes on the network segment. The
OkiLAN 6020e cannot find a free node number.
Remove some of the other nodes on the network or
expand the network range for this segment of the
network.
OkiLAN 6020e Utility
OkiLAN 6020e does not show up in utility—If the
OkiLAN 6020e does not appear in the utility, try the
following:
• Print a configuration sheet for name and zone
information. Run the Chooser and select the correct
zone.
• Verify the OkiLAN 6020e is powered on and
appears in the Chooser. If not, refer to general
EtherTalk troubleshooting.
• Verify the Macintosh you are using is running Phase
2 EtherTalk.
VI - 10
OKI OkiLAN 6020e User’s Guide
• Compare the zone in which the OkiLAN 6020e
appears in the Chooser to the zones searched. Search
the same zone where the OkiLAN 6020e appears in
the Chooser.
OkiLAN 6020e Utility Errors
Message: AppleTalk network is inaccessible.
Recommended Action: Examine network connections
and verify AppleTalk is active in the Chooser.
Message: Device limit exceeded. First 100 devices will
be shown.
Recommended Action: There are a maximum of 100
devices. Reduce the number of zones you are searching
and try again.
Message: Device returned invalid local zone list.
Recommended Action: Verify proper router operation.
Message: Incompatible version of OkiLAN 6020e
utility.
Recommended Action: Call 1-800-OKI-DATA
(1-800-654-3282).
Message: NBP Lookup Error.
Recommended Action: Try again.
Message: “Name” @ “Zone” is busy.
Recommended Action: Unable to change the
configuration at this time. Try again.
Message: “Name” @ “Zone” is not responding. Verify
the OkiLAN 6020e is powered on. To reconnect with the
device, return the zone selection window and search
again.
Recommended Action: The device did not respond. If
a reset has just taken place, the OkiLAN 6020e may not
be registered on the network yet. Verify the OkiLAN
6020e is powered on. Search the network again to find
the device.
OKI OkiLAN 6020e User’s Guide
VI - 11
EtherTalk
Section 6 - Appendix A - Troubleshooting
Section 6 - Appendix A - Troubleshooting
Message: No OkiLAN 6020e device(s) found. Verify the
OkiLAN 6020e is powered on.
Recommended Action: Confirm the device is powered
on and the LED is green. Verify correct zone to search
by printing a configuration sheet.
Message: Option is not available with this product.
Recommended Action: This configuration option is
not available with this product.
Message: Only the first 1024 zones found will be
displayed.
Recommended Action: Reduce the number of zones
on your network.
Message: Router zone requested failed.
Recommended Action: The OkiLAN 6020e utility is
unable to communicate with the router and to locate the
zones. Confirm proper router operation.
Message: The change could not be verified.
Recommended Action: The change will take place
when the OkiLAN 6020e is idle. If it is power cycled or
reset before it becomes idle, changes will be lost.
Return to the zone selection window and search the
network again to display the new information.
Message: There is not enough memory to perform the
requested action.
Recommended Action: Closing windows or quitting
application programs on the Macintosh can make more
memory available.
Message: This option is not valid while the port is
disabled. Enable the port before using this option.
Recommended Action: Cannot reconfigure the device
while the port is disabled.
Message: Unexpected AppleTalk error.
Recommended Action: Check the network connection.
Try again.
VI - 12
OKI OkiLAN 6020e User’s Guide
EtherTalk
Section 6 - Appendix B - Selecting Your Printer
Appendix B
Selecting Your Printer
To Select Your Printer
1. Click on the Apple in the menu bar and select
Chooser.
2. Click on the Print Driver icon. If a caution box
appears, click OK.
If the Print Driver icon doesn’t appear in the left side of
the box, the Printer Resource files are not installed, or
you may have installed the Printer Resource files in a
different System Folder.
If AppleTalk is inactive, a caution dialog box will
appear on your screen. Click OK. The Active button
will be selected.
Zones
If your AppleTalk network is linked to other networks,
zones will appear in the Chooser. Zones are a grouping
of different networks. They can be grouped by physical
location. For example, Zone 1 may contain all the
printers on the network Group 1, but may also be
grouped by logical zones. Printers can be connected to
the same physical cable but can service other zones.
The highlighted zone is the zone where your computer
resides on your network. The printer selection box lists
the names of the devices that reside in your computer’s
zone.
1. Click on the zone in the AppleTalk Zones box where
your printer is located. (You may also need to scroll
through the zones to locate the one you want.) If you
do not know the zone in which your printer is
located, contact your network administrator.
OKI OkiLAN 6020e User’s Guide
VI - 13
Section 6 - Appendix C - Capturing with a Spooler
2. Click on the printer name you want to use.
Note: If your printer is the only name listed in the
box, it still must be selected. Your printer will
remain selected until you choose a different
printer with your Chooser.
3. Click on the Close box to exit the Chooser.
4. Print a directory from your Macintosh by selecting
Print Directory, Print Window or Print Desktop
from the File pull-down menu. If your printer prints
a directory, you have connected your printer to your
network correctly.
Appendix C
Capturing With a Spooler
Overview
To use the OkiLAN 6020e with the AppleShare Print
Server, follow these steps to capture the OkiLAN
6020e.
Capturing without Bypass
Capturing
1. Use the OkiLAN 6020e utility and do the following:
a) Change Type 1 to LaserShared
b) Change Type 2 to LaserWriter
2. Capture with print spooler.
3. Use the OkiLAN 6020e utility to remove Type 2.
The two device types should be:
• Type 1 : LaserShared
• Type 2 : (none)
VI - 14
OKI OkiLAN 6020e User’s Guide
EtherTalk
Section 6 - Appendix C - Capturing with a Spooler
Releasing
1. Use the OkiLAN 6020e utility to:
a) Change Type 1 to LaserWriter
b) Change Type 2 to LaserShared
2. Release the OkiLAN 6020e from the print spooler
application.
3. Use the OkiLAN 6020e utility to remove Type 2.
The two device types should be:
• Type 1 : LaserWriter
• Type 2 : (none)
Capturing with Bypass
Capture or release without using the OkiLAN 6020e
utility.
OKI OkiLAN 6020e User’s Guide
VI - 15
Section 6 - Appendix C - Capturing with a Spooler
VI - 16
OKI OkiLAN 6020e User’s Guide
Windows Printing
Windows Printing
Section VII:
Section 7 - Windows Printing
In This Section
Chapter 1 OkiLAN 6020e Set Up for
Windows NT 4.0/2000 ........................................... VII-3
Overview .................................................... VII-3
OkiLAN 6020e Connect for IP ................... VII-3
OkiLAN 6020e Connect for DLC .............. VII-6
Using the Windows NT 4.0 LPR Print
Monitor ..................................................... VII-7
Chapter 2 OkiLAN 6020e Set Up for
Windows 95/98 ................................................... VII-10
Overview .................................................. VII-10
OkiLAN 6020e Connect for TCP/IP ........ VII-10
OkiLAN 6020e Connect for DLC ............ VII-12
Output Port Configuration Options .......... VII-14
Enabling/Disabling ................................... VII-14
VII - 2
OKI OkiLAN 6020e User’s Guide
Section 7 - Chapter 1 - OkiLAN 6020e Setup for Windows NT
Chapter 1
OkiLAN 6020e Set Up for
Windows NT 4.0/2000
This section contains instruction and information on
how to set up your OkiLAN 6020e for a Windows NT
4.0/2000 environment. Print options for Windows NT
4.0/2000 include:
• OkiLAN 6020e Connect for IP
• OkiLAN 6020e Connect for DLC
• LPR
OkiLAN 6020e Connect for IP
OkiLAN 6020e Connect for TCP/IP is a full featured
utility that allows simple, direct, TCP/IP printing from
your computer to a printer attached to an OKI TCP/IP
enabled print server. OkiLAN 6020e Connect has
advantages over other TCP/IP printing options. It
allows you to print to print servers that are using
Dynamic IP addresses (DHCP). It will also notify you
immediately in the event of a printer error (e.g. Paper
out). Print jobs printed through OkiLAN 6020e
Connect are sent directly to the OkiLAN 6020e print
server and not routed through a network server,
resulting in a reduction of network traffic.
System Requirements
To use OkiLAN 6020e Connect for TCP/IP for your
Windows NT 4.0/2000 operating system, your
computer must be configured to run TCP/IP. The
OkiLAN 6020e print server must also be configured to
run TCP/IP.
OKI OkiLAN 6020e User’s Guide
VII - 3
Windows Printing
Overview
Section 7 - Chapter 1 - OkiLAN 6020e Setup for Windows NT
Installation
To install OkiLAN 6020e Connect for TCP/IP, follow
the instructions below:
1. Install the OkiLAN 6020e Connect for TCP/IP files see Section I.
2. When installation is complete, click on Start,
Settings and then Printers.
3. Select the Windows printer from which you would
like to print with the OkiLAN 6020e Connect, then
select Properties from the menu.
4. Add an OkiLAN 6020e Connect port. This may be
done by selecting Add Port under the Ports tab.
VII - 4
OKI OkiLAN 6020e User’s Guide
Section 7 - Chapter 1 - OkiLAN 6020e Setup for Windows NT
You will enter into the Add OkiLAN 6020e Connect
Port screen where there will be a list of all OkiLAN
6020e print servers available on the local subnet.
6. If the port you wish to add is listed in the Ports
available on local subnet: window, select the port
name and click Add.
If the port you wish to use is not listed, click the
Locate non-local device button and enter the Static
IP Address used for the print server. Click the Add
button.
Note: The OkiLAN 6020e Connect DHCP discovery
feature will relocate a print server on the local
subnet by its port name, even if the IP address
changes. This feature is enabled on the local
subnet only. A non-local print server will not be
re-discovered if the IP address changes.
7. Click OK.
You will now be able to use OkiLAN 6020e Connect
for TCP/IP. Whenever you print to the printer
configured with OkiLAN 6020e Connect, your print
job will go directly to the OkiLAN 6020e print server
port.
OKI OkiLAN 6020e User’s Guide
VII - 5
Windows Printing
5. From the list of Available Printer Ports, select OKI
OkiLAN 6020e Connect IP Monitor as the type of
port to add and click New Port.
Section 7 - Chapter 1 - OkiLAN 6020e Setup for Windows NT
Notify When Printed
This feature will provide an alert when your job is
active on the printer. This may be useful if the printer is
especially busy.
Description
An optional field where you may list the location or
other useful information about the printer port.
OkiLAN 6020e Connect for DLC
OkiLAN 6020e Connect for Data-Link Control (DLC)
provides a direct printing solution for users in
Microsoft Windows NT serverless environments with
the DLC/LLC protocol. Print jobs printed through
OkiLAN 6020e Connect are sent directly to the
OkiLAN 6020e print server and not routed through the
network server, resulting in a reduction of network
traffic. OkiLAN 6020e Connect for DLC can be used to
configure the print server, obtain status from the print
server and printer, and send jobs to the printer.
Note: To obtain a version of OkiLAN 6020e Connect
for DLC that supports Windows NT, visit our
FTP site (ftp://ftp.extendsys.com/pub/
printserver/utilities/) or contact Technical
Support.
Configure Port
If you have printing problems while using the OkiLAN
6020e Connect printing port, you may check the status
of the port by selecting Configure Port under the Ports
tab in the Properties screen.
Notify On Printer Error
This feature will check the printer status prior to
printing the job. If a printer error is detected (e.g.
printer off-line or out of paper) the error description
will be given.
VII - 6
OKI OkiLAN 6020e User’s Guide
Section 7 - Chapter 1 - OkiLAN 6020e Setup for Windows NT
Notify When Printed
This feature will provide an alert when your job is
active on the printer. This may be useful if the printer is
especially busy.
An optional field where you may list the location or
other useful information about the printer port.
Using the Windows NT 4.0 LPR Print
Monitor
A Microsoft LPR print monitor is shipped with
Windows NT 4.0. This print monitor is not included in
the default Windows NT installation; therefore, it will
need to be installed. In order to set up an LPR printer in
Windows NT 4.0, the system must have an IP address,
the print server must have an IP address, and Microsoft
TCP/IP printing must be installed.
System Requirements
• Administrator privileges
• Windows NT installation disks or CD
Install TCP/IP on NT Server
If Microsoft TCP/IP has not been installed on the
Windows NT print server, follow the steps below:
1. Open the Windows NT Control Panel.
2. Double-click the Network icon.
3. Select the Protocols tab.
4. Select TCP/IP Protocol and click the Properties
button.
5. Assign the server an IP address (for LANs without
Internet access, it is suggested to use 10.10.10.1).
Click OK.
OKI OkiLAN 6020e User’s Guide
VII - 7
Windows Printing
Description
Section 7 - Chapter 1 - OkiLAN 6020e Setup for Windows NT
Install LPR Print Monitor
1.
2.
3.
4.
5.
Open the Windows NT Control Panel.
Select the Services tab.
Select Add, then Microsoft TCP/IP printing.
Click the Close button.
Restart the system.
Assign Print Server IP Address
1. Using OkiNet for IP, assign the print server an IP
address; for example, 10.10.10.2.
Note: For more information on using OkiLAN 6020e
TCP/IP, see OkiNet for TCP/IP.
Add LPR Printer
1. Open the Control Panel, Printers and then select
Add Printer.
2. Select My Computer and click Next.
3. Click the Add Port button.
4. On the Printer Ports screen, select LPR Port from
the list of Available Printer Ports and click the New
Port button.
VII - 8
OKI OkiLAN 6020e User’s Guide
Section 7 - Chapter 1 - OkiLAN 6020e Setup for Windows NT
6. In the Name of printer or print queue on that server:
field, enter the print server output port being used.
For example, for port 1 enter P1, for port 2 enter P2,
etc. Click OK.
7. Click OK.
8. Verify the port just added is selected and then click
Next.
9. Select a printer driver and click Next.
10. Enter a name for the printer and click Next.
11. To share the printers with others on the network,
select Shared and enter a share name for the
printer.
OKI OkiLAN 6020e User’s Guide
VII - 9
Windows Printing
5. In the Name or address of server providing lpd:
field, enter the IP address you assigned to the printer.
Section 7 - Chapter 2 - OkiLAN 6020e Setup for Windows 95/98
Chapter 2
OkiLAN 6020e Set Up for
Windows 95/98
Overview
This section contains instruction and information on
how to set up your OkiLAN 6020e for a Windows 95/
98 environment. Print options for Windows 95/98
include:
• OkiLAN 6020e Connect for TCP/IP
• OkiLAN 6020e Connect for DLC
• OkiLAN 6020e Connect for IPX/SPX
OkiLAN 6020e Connect for TCP/IP
OkiLAN 6020e Connect for TCP/IP is a full featured
utility that allows simple, direct, TCP/IP printing from
your computer to a printer attached to an OKI TCP/IP
enabled print server. With OkiLAN 6020e Connect,
you can even print to print servers using Dynamic IP
addresses (DHCP). Print jobs printed through OkiLAN
6020e Connect are sent directly to the OkiLAN 6020e
print server and not routed through the network server,
resulting in a reduction of network traffic.
System Requirements
To use OkiLAN 6020e Connect for TCP/IP, your
operating system must be Windows 95/98 and your
computer must be configured to run TCP/IP. The
OkiLAN 6020e print server must also be configured to
run TCP/IP.
Installation
To install OkiLAN 6020e Connect for TCP/IP:
1. Install the OkiLAN 6020e Connect for TCP/IP-see
Section I.
2. When installation is complete, click on Start,
Settings and then Printers.
VII - 10
OKI OkiLAN 6020e User’s Guide
3. Select the Windows printer from which you would
like to print with OkiLAN 6020e Connect, then
select Properties from the File menu.
4. Add an OkiLAN 6020e Connect port. This may be
done by selecting Add Port under the Details tab.
5. In the Add Port window, select the radio button
labeled Other and then select OKI OkiLAN 6020e
Connect IP Monitor as the type of port to add.
6. Click OK.
You will enter into the Add OkiLAN 6020e Connect
Port screen where there will be a list of all OkiLAN
6020e print servers available on the local subnet.
7. If the port you wish to add is listed in the Ports
available on local subnet window, select the port
name and click the Add button.
If the port you wish to use is not listed, click the
Locate non-local device button and enter the Static
IP Address used for the print server. Click the Add
button.
Note: The OkiLAN 6020e Connect discovery feature
will relocate a print server by the port name,
even if the IP address changes. This feature is
enabled on the local subnet only. Non-local
print servers will not be re-discovered if the IP
address changes.
OKI OkiLAN 6020e User’s Guide
VII - 11
Windows Printing
Section 7 - Chapter 2 - OkiLAN 6020e Setup for Windows 95/98
Section 7 - Chapter 2 - OkiLAN 6020e Setup for Windows 95/98
8. Click OK.
You will now be able to use OkiLAN 6020e Connect
for TCP/IP. Whenever you print to the printer
configured with OkiLAN 6020e Connect, your print
job will go directly to the OkiLAN 6020e print server
port.
Port Settings
If you have printing problems while using the OkiLAN
6020e Connect printing port, you may check the status
of the port by selecting Port Settings under the Details
tab in the Properties screen.
OkiLAN 6020e Connect for DLC
OkiLAN 6020e Connect for Data-Link Control (DLC)
provides a direct printing solution for users in
Microsoft Windows 95/98 serverless environments
with the DLC/LLC protocol. Print jobs printed through
OkiLAN 6020e Connect are sent directly to the
OkiLAN 6020e print server and not routed through the
network server, resulting in a reduction of network
traffic. OkiLAN 6020e Connect for DLC can be used to
configure the print server, obtain status from the print
server and printer, and send jobs to the printer.
System Requirements
To use OkiLAN 6020e Connect for DLC, your
operating system must be Windows 95/98 and the
Microsoft 32-bit DLC protocol must be installed.
Installation
To install OkiLAN 6020e Connect for DLC, follow the
instructions below:
1. Install OkiNet for DLC — see Section I.
2. When the installation is complete, click on Start,
Settings and then Printers.
3. Select the printer driver from which you would like
to print with OkiLAN 6020e Connect, then select
Properties from the File menu.
VII - 12
OKI OkiLAN 6020e User’s Guide
Section 7 - Chapter 2 - OkiLAN 6020e Setup for Windows 95/98
Windows Printing
4. Add an OkiLAN 6020e Connect port. This may be
done by selecting Add Port under the Details tab.
5. In the Add Port window, select the radio button
labeled Other and select OKI OkiLAN 6020e
Connect DLC Monitor as the type of port to add.
6. Click OK.
You will enter into the Add OkiLAN 6020e Connect
Port screen where there will be a list of all OkiLAN
6020e print servers available on the local subnet.
7. Select the OkiLAN 6020e print server port name and
click the Add button.
8. Click OK.
You will now be able to use OkiLAN 6020e Connect
for DLC. Whenever you print to the printer configured
with OkiLAN 6020e Connect, your print job will go
directly to the OkiLAN 6020e print server port.
Port Settings
If you have printing problems while using the OkiLAN
6020e Connect printing port, you may check the status
of the port. Select the Details tab on the Properties
screen and then click the Port Settings button.
For more configuration options, click the Configure
button.
OKI OkiLAN 6020e User’s Guide
VII - 13
Section 7 - Chapter 2 - OkiLAN 6020e Setup for Windows 95/98
Output Port Configuration Options
To configure the OkiLAN 6020e output port, select the
Output Port tab.
Port Number
Select the port number you wish to configure.
Configuration Page Language
Select the appropriate printer language for printing and
configuration pages on your printer.
Enabling/Disabling
To enable or disable protocols on the OkiLAN 6020e,
select the Protocols tab. Select each protocol you wish
to enable. If you disable a protocol, the OkiLAN 6020e
will no longer communicate using that protocol.
VII - 14
OKI OkiLAN 6020e User’s Guide
OkiView 32
OkiView 32
Section VIII:
Section 8 - OkiView 32
In This Section
Chapter 1 Introduction ............................................ VIII-3
OkiView 32 Installation Requirements ......VIII-3
Chapter 2 OkiView 32 Printer Panel .................... VIII-4
OkiView 32 Printer Properties Menu .......... VIII-4
Changing the Printer’s Name and Location VIII-6
OkiView 32 Discovery Preferences ............VIII-6
VIII - 2
OKI OkiLAN 6020e User’s Guide
Section 8 - OkiView 32
Chapter 1
Introduction
OkiView 32 Installation Requirements
Note: Novell’s Client for Windows 95/98, NT or 2000 is required for
OkiView 32. Microsoft Client is required only for configuring Novell
using a Microsoft network.
Insert the OkiView 32 CD into your CD-ROM drive and run
Setup.exe.
OKI OkiLAN 6020e User’s Guide
VIII - 3
OkiView 32
The OkiView 32 Utility provides a simple, quick way of viewing the
status of all brands of network printers on Microsoft/Novell
networks, as well as configuring and maintaining Oki network
printers on those networks. The main screen contains the OkiView
Printer List of network printers, and provides the starting point to
select and manage print devices from Windows 95, 98, NT and 2000
workstations on the network.
This section gives a summary of OkiView 32’s features. For more
details, see the OkiView on-line Help.
Please note that not all OkiView 32 features may be supported by
the particular OKI printer or OkiLAN print server model which you
are using. For example, the OkiLAN 6020e does not support the
NetBEUI protocol.
Section 8 - OkiView 32
Chapter 2
OkiView 32 Printer Panel
The Printer Panel is the OkiView 32 main display. The display is
divided into two smaller panels: the Printer Filters Panel and the
Printer Information Panel. The Printer Information Panel, on the
right hand side of the main display, shows a list of all the printers
currently available for status and configuration. Printer name and
status information is detailed to the right of the printer icon.
OkiView 32 Printer Properties Menu
The Printer Properties menu allows you to get detailed status
information and to configure printers. To enter the Printer
Properties menu:
1 Select a printer on the Printer Information Panel.
2 From the Printer menu, click Printer Properties, or click the
Printer Properties icon, or double-click on the selected printer.
Note: Modification of printer options (print quality, page setup,
paper source, etc.) is not available for Internet FAX and non-Oki
printers.
VIII - 4
OKI OkiLAN 6020e User’s Guide
Section 8 - OkiView 32
Network Property Page
The Network Property Page is reached from the Printer Properties
menu. This screen allows you to configure the network protocol,
network frames, and SNMP traps events and destination addresses.
Information includes:
• Protocols
- TCP/IP
- NetWare
- AppleTalk
- NetBEUI
- Lan Manager
- Banyan VINES
• Frame Types
• SNMP Traps
Novell Configuration
Note: This screen is only available when Novell’s Client for
Windows 95/98, NT or 2000 is installed.
The Novell Configuration screen is reached from the Printer
Properties menu. This screen allows you to configure Novell
NetWare without accessing standard DOS-based NetWare utilities
such as Pconsole.
The Novell Configuration screen is separated into two panels:
Novell List Panel
This panel displays the following information:
• QueueServer/PServer in bindery mode
• QueueServer/PServer in NDS mode
• Remote Printer/NPrinter mode
Novell Information Panel
This panel allows you to change the settings displayed in the
Novell List Panel.
OKI OkiLAN 6020e User’s Guide
VIII - 5
OkiView 32
Status
The Status screen is reached from the Printer Properties menu. This
screen displays descriptive information about the printer, as well as
its online/offline status and the status text displayed on the
printer’s front panel.
Section 8 - OkiView 32
Changing the Printer’s Name and Location
1
2
3
4
Select a printer on the Printer Information Panel.
From the Printer menu, click Printer Properties.
Change the text in the name and/or location fields.
Click OK.
OkiView 32 Discovery Preferences
This screen allows the user to customize these settings:
• Network Protocolssets which protocol (TCP/IP or NetWare)
is used to discover a network printer.
• TCP/IP Subnetsallows you to search one or more subnets to
discover a network printer.
• IPX/SPX Segmentsallows you to search one or more NetWare
segments to discover a network printer.
• Printer Refresh Polling Intervalsets the rate at which OkiView
32 polls the network for new print jobs.
VIII - 6
OKI OkiLAN 6020e User’s Guide
Section IX:
Regulatory Information
Regulatory
Information
Section 9 - Regulatory Information
Federal Communications
Commission Radio Frequency
Interference Statement
This equipment generates and uses radio frequency
energy. If not installed and used according to the
manufacturer’s instructions, this equipment may
cause interference with radio/TV reception.
The Federal Communications Commission has
established technical standards regarding radio
frequency energy emitted by computing devices.
This equipment complies with Part 15 of the FCC
Rules, subject to the following conditions: This
device may not cause harmful interference; and it
must accept any interference received, including
interference that may cause undesired operation.
There is no guaranteed that interference will not
occur in a particular installation. If you suspect that
this equipment is interfering with radio/TV reception
try the following:
• While observing the interference, turn the suspect
equipment off and back on. If the inteference
stops when you turn the equipment off , and
starts again when you turn the equipment on, the
equipment is probably the source of your
problem.
• Connect the equipment and the receiver to
different electrical outlets.
• Increase the distance between the equipment and
the receiver.
• Reorient or relocate the receiving antenna.
• Consult your dealer or an experienced radio/TV
technician for additional advice.
OKI is not responsible for radio/TV interference
caused b using unauthorized cables or by making
unauthorized changes to this equipment.
IX - 2
OKI OkiLAN 6020e User’s Guide
A
Advanced Configuration
Options
OkiLAN 6020e utility
(EtherTalk), VII-6
Advanced Management
Features
network alert, II-18
OkiNet for TCP/IP, II-19
printer security for TCP/IP
Printing, II-19
security, II-5
Advanced management
Features
OkiNet for NDS, II-19
Assigning an IP Address
BOOTP, IV-11 to IV-12,
IV-57 to IV-59
DHCP, IV-10
gleaning, IV-9
RARP, IV-11 to IV-12,
IV-60 to IV-62
static route entry, IV-11
B
Bindery Settings
in NetWare, III-8
BOOTP
assigning an IP address,
IV-11 to IV-12, IV-57 to
IV-59
troubleshooting, IV-50,
IV-51
BOOTP Server
starting in OkiNet for
TCP/IP, IV-41
BSD-Style Print Queue
configuring in TCP/IP,
IV-17 to IV-18
C
Choosing a TCP/IP IP address,
IV-7
CLC/802.2 Protocol Stack,
VI-4
Client Nodes, VI-3
Configuration Sheet
printing
EtherTalk, VII-6
NetWare, III-17
TCP/IP, IV-34
troubleshooting
in TCP/IP, IV-54
Configuration Sheet Printing,
LAN Manager/LAN Serv, VI10
Configuring for TCP/IP
Network Printing, IV-15
Creating an OS/2 Printer
LAN Manager/LAN Server,
VI-9
Custom Views
creating
in OkiNet for NetWare,
III-19
in OkiNet for TCP/IP,
IV-36
in TCP/IP, II-19
D
Default Gateway IP Address
identifying in telnet, IV-46
DHCP
assigning an IP address,
IV-10
Index
Index
Index
Diagnostic Information
displaying in NetWare,
III-17
DLC/802.2 Protocol Stack,
VI-4
E
Enabling/Disabling Protocols
OkiNet for NetWare, III-17
OkiNet for TCP/IP, IV-32
Error Messages
EtherTalk, VII-11 to VII-12
TCP/IP hardware, IV-53
EtherTalk
OkiLAN 6020e utility
advanced configuration
options, VII-6
enable port option, VII-7
error messages, VII-11 to
VII-12
finding the OkiLAN
6020e, VII-4
printing a configuration
sheet, VII-6
renaming the OkiLAN
6020e printer, VII-5
reset board option, VII-7
restore defaults, VII-7
running, VII-4
selecting a zone, VII-5
set type option, VII-6
status option, VII-6
selecting your printer,
VII-13 to VII-14
G
GET Community Name
(TCP/IP), IV-31
Gleaning, Assigning an IP
Address, IV-9
H
HP-UX v10.xx Application
prerequisites, IV-67
procedure, IV-68
HP-UX v8.07 Application
prerequisites, IV-63 to IV-64
procedure, IV-64 to IV-66
HP-UX v9.xx Application
Prerequisites, IV-67
procedure, IV-68 to IV-69
I
F
FCC Statement, 2
Federal Communications
Commission Statement, 2
Index - 2
FTP Printing
ASCII, IV-20
BINARY, IV-20
BYE, IV-20
CLOSE, IV-20
IMAGE, IV-20
MODE, IV-20
MPUT, IV-19
OPEN, IV-20
PUT, IV-19
QUIT, IV-20
SEND, IV-19
STRU, IV-20
TYPE, IV-20
FTP Troubleshooting, IV-49 to
IV-55
IBM AIX ver. 3.x Application
prerequisites, IV-75
procedure, IV-75 to IV-77
OKI OkiLAN 6020e User’s Guide
INSTALL, LAN Manager/LAN
Server
installation, VI-7
running the utility, VI-7
IP Address
assigning
BOOTP, IV-11 to IV-12
DHCP, IV-10
gleaning, IV-9
RARP, IV-11 to IV-12
static route entry, IV-11
choosing, IV-7
J
JetAdmin Support, II-6 to II-7
AppleTalk configuration,
II-7
NetWare configuration, II-6
to II-7
obtaining diagnostic
information, II-7
TCP/IP configuration, II-7
L
LAN Manager/LAN Server
INSTALL, VI-7
Language Switching
NetWare, III-11 to III-12
N
NDPS, III-33
NDS Settings in NetWare, III-9
NPrinter Mode in NetWare,
III-5
O
OkiLAN 6020e Diagnostic
Information
displaying in OkiNet for
TCP/IP, IV-34
OkiLAN 6020e Utility
(EtherTalk)
advanced configuration
options, VII-6
enable port option, VII-7
error messages, VII-11 to
VII-12
finding the OkiLAN 6020e,
VII-4
renaming the OkiLAN
6020e printer, VII-5
reset board option, VII-7
restore defaults, VII-7
running, VII-4
selecting a zone, VII-5
set type option, VII-6
status option, VII-6
OkiNet Connect
for DLC, VIII-12 to VIII-13
for TCP/IP, VIII-3 to
VIII-6, VIII-10 to VIII-12
OkiNet for NDS, III-24 to III-32
adding or removing the
print serv, III-31
configuring the OkiLAN
6020e, III-31
creating a new OkiLAN
6020e object, III-28
installing, III-27
printing with an OkiLAN
6020e print server, III-29
to III-30
OkiNet for NetWare
configuration options, III-7
customized views, creating,
III-19
enabling/disabling protocols, III-17
NetWare queues configuration options, III-9
output port configuration
options, III-11 to III-13
OKI OkiLAN 6020e User’s Guide
Index - 3
Index
Index
Index
port configuration options,
III-10
resetting the OkiLAN
6020e, III-17
restoring factory default
settings, III-18
running the utility, III-7
searching for a specific
OkiLAN 6020e, III-19
SNMP access information,
III-22 to III-23
view settings, modifying,
III-20 to III-22
OkiNet for OS/2
configuring a print server,
VI-13 to VI-14
deleting a local port, VI-13
running the utility, VI-7 to
VI-8
OkiNet for TCP/IP
running the utility, IV-24
starting a BOOTP server,
IV-41
troubleshooting, IV-49 to
IV-55
OkiNet Utilities
introduction, I-9
OkiView 32, I-9, I-11, 3
OS/2 Printer, Creating, VI-9
Output Port Configuration
Options
in NetWare, III-11 to III-13
in TCP/IP, IV-28 to IV-30
P
Port Configuration
in NetWare, III-10
Print Queue, Configuring
BSD-Style, IV-17 to IV-18
Print Server Class, Adding or
Removing in OkiNet f, III-31
to III-32
Index - 4
Printer Traps in TCP/IP, IV-33
Printing
in the OS/2 environment,
VI-11 to VI-12
OkiLAN 6020e
connect for DLC, VIII-12
connect for TCP/IP,
VIII-3, VIII-10, VIII-10
to VIII-12
PServer Mode in NetWare, III-5
Q
Queues, NetWare configuration options, III-9
R
RARP
assigning an IP address,
IV-11 to IV-12, IV-60 to
IV-62
troubleshooting, IV-49 to
IV-55
Raw Port Printing, IV-22
Regulatory Information, 2
Remote LPD Printing, IV-18 to
IV-19
Remote Print Queue Name,
FF/LF/NF, IV-16
Resetting the OkiLAN 6020e
in NetWare, III-17
Restoring Factory Default
Settings
in NetWare, III-18
in TCP/IP, IV-35
Routers, VI-4
RPrinter Mode in NetWare,
III-5, III-8
OKI OkiLAN 6020e User’s Guide
S
SCO UNIX Application
prerequisites, IV-73
procedure, IV-74
Security in SNMP, II-5
Selecting a Zone in EtherTalk,
VII-5
Selecting Your Printer in
EtherTalk, VII-13 to VII-14
Set Community Name in
TCP/IP, IV-31
SNMP
configuration options,
OkiNet for TCP/IP, IV-30
to IV-31
private MIB, II-3 to II-4
traps, II-4 to II-5
Solaris 2.x Application
prerequisites, IV-78
procedure, IV-78
Static Route Entry
assigning an IP address,
IV-11
troubleshooting, IV-52
Sun-OS v4.1.x Application
prerequisites, IV-79 to IV-80
procedure, IV-80
T
TCP/IP
configuration overview,
IV-5
network printing, configuring for, IV-15
OkiLAN 6020e connect for
TCP/IP, VIII-4 to VIII-6
Telnet Session
configuring port information, IV-46 to IV-47
identifying default gateway
IP address, IV-46
running, IV-43
specifying print server IP
address, IV-45
specifying the subnet mask
for your network, IV-45
starting, IV-41
Timeout Checking, IV-21
Trap Community Name in
TCP/IP, IV-31
Trap Destination in TCP/IP,
IV-33
Traps, SNMP, II-4 to II-5
configuration, III-15 to
III-16
Troubleshooting
EtherTalk
Macintosh chooser, VII-8
network error messages,
VII-10
OkiLAN 6020e utility,
VII-10 to VII-11
unable to print, VII-9 to
VII-10
LAN Manager/LAN Server
no configuration sheet,
VI-17
unable to print, VI-17
TCP/IP
BOOTP, IV-50
FTP, IV-55
gleaning, IV-50
hardware error messages,
IV-53
OkiNet for TCP/IP utility,
IV-53
RARP, IV-50
OKI OkiLAN 6020e User’s Guide
Index - 5
Index
Index
Index
Verifying Access to the
OkiLAN 6020e, IV-13
View Settings, Modifying
in NetWare, III-20
in OkiNet for TCP/IP, IV-37
Web JetAdmin Support, II-8 to
II-9
configuring the OkiLAN
6020e, II-8
installing a Windows NT
printer, II-8 to II-9
obtaining diagnostic
information, II-9
Windows 95
DLC requirements, VIII-12
OkiNet connect for DLC,
VIII-12 to VIII-13
OkiNet connect for TCP/IP,
VIII-10 to VIII-12
TCP/IP requirements,
VIII-10
Windows NT 4.0
connect for DLC, VIII-6 to
VIII-7
OkiLAN 6020e setup, VIII-3
to VIII-9
requirements, VIII-3
Winsock Troubleshooting,
IV-53
W
Z
Web Configuration, II-10 to
II-17
Admin configuration, II-12
to II-14
connecting to the OkiLAN
6020e, II-10 to II-11
OkiLAN 6020e server
discovery, II-16
reset, II-16
status information, II-15
support menu, II-15
Web Configuration
for TCP/IP, IV-42
Zone, Selecting in EtherTalk,
VII-5
restoring to factory
defaults, IV-49
static route entry, IV-52
unable to assign IP
address, IV-50 to IV-53
unable to print, IV-54 to
IV-55
UNIX BOOTP, IV-51
Winsock errors, IV-53
U
Ultrix v4.2 Application
prerequisites, IV-79 to IV-80
procedure, IV-80
UNIX BOOTP Troubleshooting, IV-51
V
Index - 6
OKI OkiLAN 6020e User’s Guide

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement