Peavey CAB 80 User's Manual

Add to my manuals
16 Pages

advertisement

Peavey CAB 80 User's Manual | Manualzz

S P E C I F I C A T I O N S

MediaMatrix

®

CAB

8i and

CAB

8o

Description

The CAB ª 8i and CAB ª 8o, respectively, are eight-input and eightoutput MediaMatrix ¨ gateways onto and off of an Ethernet network for real-time

MediaMatrix ¨ audio distribution and control. They employ Cobranet proprietary protocol to ensure seamless, error-free transmission of high-quality real-time audio without drop-outs or lossy compression across a 100baseT Ethernet network.

The CAB ª 8i uploads eight channels of either microphone-level or line-level analog audio signals onto an Ethernet network. Each input channel has software controlled, continuously variable analog input gain from -9 dB to +60 dB in 1 dB steps. Each has 48-volt phantom power and a 20 dB mic/line pad. Both functions are software switchable.

The CAB 8o downloads eight channels of line-level analog audio signals from an

Ethernet network. Maximum output levels are individually jumper-selectable between

+24 dBu, +18 dBu, +12 dBu, and +6 dBu.

In addition to eight input or output audio paths, both products incorporate eight voltage-control input ports, eight software controlled TTL outputs port, eight software controlled relays with both normally open and normally closed contacts, an RS-485 port with multi-drop connections, and two word-clock linking BNC connectors.

Features

¥ Eight channels of either microphone or line-level audio transmitted onto an Ethernet network using CobraNet ª protocol sampled at 48 kHz (CAB 8i).

¥ Eight channels of line-level audio transmitted from an Ethernet network using CobraNet protocol sampled at

48 kHz (CAB 8o).

¥ A/D converters are 24-bit, 64 times oversampling, using delta-sigma modulation (CAB 8i).

¥ D/A converters are 24-bit, 128 times oversampling, using delta-sigma modulation (CAB 8o).

¥ 48-volt phantom power for microphone inputs, individually software switchable on each input channel (CAB 8i).

¥ 24- or 20-bit transmission quantization at a 48 kHz sampling rate.

¥ Eight channels of analog control voltage input ports which allow external switches, potentiometers, or voltage sources to control MediaMatrix software parameters via an Ethernet link.

¥ Eight channels of TTL control outputs ports which are software controllable via an Ethernet link.

¥ Eight relays, with both normally open and normally closed contacts, which allow software control of external devices via an Ethernet link.

¥ A non-Ethernet RS-485 control port with two mulit-drop connections.

¥ Two word clock linking connectors that enable auto-switch-over to a second unit, should one unit fail.

¥ One rack-unit (1-3/4"), fan-cooled chassis.

Applications

¥ Stadiums

¥ Cruise ships

¥ Multi-purpose facilities

¥ Auditoriums

¥ Large-scale paging systems

¥ Schools

¥ Courts of law

¥ University campus buildings

¥ Theme parks

¥ Performing arts centers

¥ Distance learning

¥ Hotel meeting rooms

¥ Houses of worship

¥ Conference centers

¥ Teleconferencing

¥ Live sound microphone snakes

¥ Civic centers

¥ Music clubs

¥ Theaters

¥ Arenas

¥ Any facility requiring distribution of multiple microphone or line-level signals

AUDIO SPECIFICATIONS

Audio Channels:

CAB 8i: Eight input channels, line-level or microphone level with switchable

48-volt phantom power.

CAB 8o: Eight output channels, linelevel with individual channel jumpers for a maximum output of +6, +12, +18, or

+24 dBu (factory default is +12 dBu for unity I/O gain).

Note: See Digital specifications, Audio

Channels per CAB 8i/8o for number of channels limitations.

Frequency Response:

20 Hz Ð 20 kHz, +0/-0.5 dB, with a

+4 dBu input signal, unity gain in and out.*

Total Harmonic Distortion:

0.01% @ 1 kHz, 0.02% @ 20 kHz, with a +4 dBu input signal, unity gain in and out*

Note: Measurements made using a 10

Hz to 30 kHz input filter on Audio

Precision System One for testing.

Dynamic Range:

Mic Level:

Ð123 dBu equivalent input noise with a

150 Ohm, Ð48 dBu input signal, no input pad, analog input gain at 60 dB, digital gain at 0 dB, analog output set for

+12 dBu maximum (factory pre-set jumper for unity gain through-put)

Note: This is equivalent to 78 dBA,

75 dB unweighted.

Line level:

95 dBA, 93 dB unweighted, with a

+12 dBu input signal, unity gain in and out*

Input CMRR (CAB 8i):

Better Than 65 dB at Any Gain

Setting:

73 dB with +12 dBu input and unity gain in and out*, 69 dB with a +4 dBu input signal and unity gain in and out*, 68 dB with a Ð56 dBu input signal, no input pad, analog input gain at 60 dB, digital gain at 0 dB, analog output set for

+12 dBu maximum (factory pre-set jumper for unity gain through-put).

Maximum Input Level (CAB 8i):

+29 dBu, with a 20 dB pad in and the analog input gain at 0 dB, +38 dBu with a 20 dB pad in and the analog input gain at Ð9 dB.

Note: The analog input gain control is not buffered with an electronically balanced amplifier and maintains a balanced input circuit with

1-dB-per-step precision and specified

CMRR.

Maximum Output Level (CAB 8o):

+24 dBu @ 600 ohms

CAB 8i Gain:

Software controlled analog gain from

Ð9d B to +60 dB, adjustable in 1 dB increments, with a software selectable analog Mic/Line input switch. (Line level selection inserts a 20 dB input pad.)

CAB 8o Gain:

Software controlled analog output gain from Ð95.5 dB to +31.5 dB, adjustable in 0.5 dB increments with internal analog output jumpers for maximum output levels of +6, +12, +18, or +24 dBu

Note: It is not recommended to use this as a microphone level output as noise will be a problem at extremely low output levels.

Input Impedance (CAB 8i):

22.2 k ohms for Line input selection and

2.2 k ohms for Mic input selection

Output Impedance (CAB 8o):

100 Ohms, designed to drive a minimum load of 600 Ohms

Analog LED Metering:

Eight peak-reading headroom meters, calibrated in dBu, monitor the analog level present at the input to the A/D converters for the CAB 8i, and at the output of the D/A converters for the CAB

8o, with the top-most red LED indicating

A/D or D/A clipping.

Note: The top-most red LED should never illuminate during normal operation.

Note 1: Audio specifications are measured from the input into the CAB 8i and the output out of the CAB 8o where relevant.

Note 2: All specifications are typical.

*Indicates no input pad, analog input gain at 0 dB, digital gain at 0 dB, analog output set for +12 dBu maximum (factory pre-set jumper for unity gain through-put).

DIGITAL SPECIFICATIONS

A/D and D/A quantization:

24-bit resolution

Audio Transmission Quantization via CobraNet

ª

:

Software switchable, 24 or 20-bit resolution

Digital Processing:

24-bit DSPÕs, 56-bit accumulators

Audio Sampling Rate and Clock

Speeds:

48 kHz audio sampling, 80 MHz DSPÕs,

12.288 MHz master clock

Audio Channels Per CAB 8i/8o:

¥ Eight with 20-bit transmission quantization selected

¥ Seven with 24-bit transmission quantization selected

CONTROL SPECIFICATIONS

CobraNet ª I/O:

100BaseT Ethernet via a standard eight-conductor RJ-45 jack

RS-485:

One port with two 3-cond. half duplex, multi-drop connections

Control Ports:

Control voltage in:

0 VDC to +10 VDC, externalpotentiometer or external-voltage-source controlled (internal 10 VDC supply provided)

Software controlled TTL (Transistorto-Transistor Logic) out:

0 VDC or +5 VDC, with a maximum current of 28 mA distributed to 8 outputs

Eight Software Controlled Relays

With Both NO and NC Contact:

Maximum contact voltage:

120 VAC or DC

Maximum contact current:

2 A

Word-Clock Ports:

Two BNC I/O ports

Note: Can be used for redundancy back-up that automaticaly switches from one CAB 8 to another if the first should fail.

GENERAL SPECIFICATIONS

Dimensions:

CAB 8i CAB 8o:

1.730" H x 19" W x 11.698" D

(4.39 cm H x 48.26 cm W x 29.71 cm D)

Net Weight:

CAB 8i: 8.5 lbs. (3.86 kg)

CAB 8o: 8.4 lbs. (3.81 kg)

AC Power:

Universal Power Supply:

1.4 A maximum, 100 to 240 VAC, 47 to 63 Hz

Power Consumption and Heat

Generation:

CAB 8i: 25 W, 85 BTU/Hr

CAB 8o: 20 W, 68 BTU/Hr

Maximum In-Rush Current:

CAB 8i and CAB 8o: less than 1.4 Amps

Finish:

Grey powder-coat painted steel

Accessories:

One detachable AC cord, four rubber adhesive feet

Product Agency Compliance

Listings:

UL, CUL, CE and FCC part 15, A

2

Frequency Response

T.H.D. versus Frequency

3

Functional Block Diagram

1.080"

27.438mm

11.698"

297.129mm

Mechanical Diagram

19.0"

482.6mm

16.840"

427.736mm

1.730"

43.942mm

4

1.730"

43.942mm

ARCHITECTSÕ AND ENGINEERSÕ

SPECIFICATIONS

Audio specifications are measured with the input fed into the CAB 8i, digitally transmitted through an Ethernet hub, and the output fed out of the CAB 8o where relevant.

CAB 8i:

The Peavey CAB 8i shall provide eight channels of either microphone or line-level audio transmitted onto an Ethernet network. It shall provide full-bandwidth, high-quality audio transmission via

100BaseT (fast) Ethernet without lossy compression techniques, drop-outs or signal degradation by employing CobraNet audio transmission protocol to make

Ethernet signal distribution deterministic.

It shall employ 24-bit A/D converters with

20- or 24-bit selectable transmission quantization utilizing a 48 kHz sampling rate.

It shall have a frequency response from

20 Hz to 20 kHz, +0/-0.5 dB or better. Its total harmonic distortion shall be no more than 0.01% at 1 kHz and 0.02% at 20 kHz with a +4 dBu input signal. It shall have a dynamic range of 95 dBA and 93 dB unweighted for line-level signals, and an equivalent input noise level of Ð124 dB for microphone level signals. Input-commonmode-rejection ratio (CMRR) shall be greater than 65 dB at any gain setting.

Maximum input level without clipping shall be +38 dBu while maintaining specified

CMRR. CAB 8i input gain shall be from

Ð9 dB to +60 dB in 1-dB steps. The CAB

8i input impedance shall be 2.2 k ohms at microphone level (20 dB pad out), and

22.2 k ohms at line level (20 dB pad in).

Control features shall include eight relays with both normally open and normally closed contacts, and eight channels of

TTL control outputs, both of which are software controllable via an Ethernet link.

Also included are eight channels of analog voltage-control ports that allow external switches, potentiometers or voltage sources to control MediaMatrix software parameters via an Ethernet link.

Front-panel indicators shall display the following status conditions: signal transmission, signal reception, transmission error, reception error, fault indication, link indication, conductor status, RS-485 control indication, and power presence. It shall have eight peakreading headroom meters to monitor the analog level present at the input to the

A/D converters, with the top-most red LED indicating A/D clipping.

Rear panel features shall include a detactable AC power cord, an AC power switch, and an AC power receptacle with a built-in auto-resetting circuit breaker.

External or internal fuses shall not be acceptable. It shall have two word-clock connectors to enable auto-switch-over should a unit fail. It shall employ detachable, euro-style, bare-wire capturing, screw-terminal connectors for ease of hook-up and trouble-shooting.

These connectors shall be used for all line-level, microphone-level, controlvoltage, TTL, relay, and RS-485 connections. The unit shall use a standard eight-conductor RJ-45 I/O jack for Ethernet connection.

Ð95.5 dB to +31.5 dB in 0.5 dB steps. The output impedance of the CAB 8o shall be

100 ohms and designed to drive a load of

600 ohms or greater.

Control features shall include eight relays with both normally open and normally closed contacts, and eight channels of

TTL control outputs, both of which are software controllable via an Ethernet link.

Also included are eight channels of analog voltage-control ports that allow external switches potentiometers or voltage sources to control MediaMatrix software parameters via an Ethernet link.

Its dimensions shall be 19 inches (48.26 cm) wide, 12 7/8 inches (32.70 cm), and 1 3/4 inches (4.44 cm) high without feet. Its net weight shall be 8.5 pounds (3.86 kg.), and its 1 rack-unit (1 3/4"), fan-cooled, steel chassis, shall be finished in grey powder coat.

It shall consume no more than 25 Watts of power and draw no more than 1.4 Amps of current. It shall be supplied with a detachable AC cable and four rubber feet.

It shall be UL, CUL, CE listed and comply with FCC part 15, A. The unit shall be

Peavey Electronics Corporation model

CAB 8i.

CAB 8o:

The Peavey CAB 8o shall provide eight channels of line-level audio transmitted from an Ethernet network. It shall provide full-bandwidth, high-quality audio transmission via 100BaseT (fast) Ethernet without lossy compression techniques, drop-outs or signal degradation by employing CobraNet audio transmission protocol to make Ethernet deterministic. It shall employ 24-bit A/D converters with

20- or 24-bit selectable transmission quantization utilizing a 48 kHz sampling rate.

Front-panel indicators shall display the following status conditions: signal transmission, signal reception, transmission error, reception error, fault indication, link indication, conductor status, RS-485 control indication, and power presence. It shall have eight peakreading headroom meters to monitor the analog level present at the output of the

D/A converters, with the top-most red LED indicating D/A clipping.

Rear panel features shall include a detachable AC power cord, an AC power switch, and an AC power receptacle with a built-in auto-resetting circuit breaker.

External or internal fuses shall not be acceptable. It shall have two word-clock connectors to enable auto-switch-over should a unit fail. It shall employ detachable, euro-style, bare-wire capturing, screw-terminal connectors for ease of hook-up and trouble-shooting.

These connectors shall be used for all line-level, control-voltage, TTL, relay, and

RS-485 connections. The unit shall use a standard eight-conductor RJ-45 I/O jack for Ethernet connection.

Its dimensions shall be 19 inches (48.26 cm) wide, 12 7/8 inches (32.70 cm), and 1 3/4 inches (4.44 cm) high without feet. Its net weight shall be 8.4 pounds (3.81 kg.), and its 1 rack-unit (1 3/4"), fan-cooled, steel chassis, shall be finished in grey powder coat.

It shall have a frequency response from

20 Hz to 20 kHz, +0/-0.5 dB or better. Its total harmonic distortion shall be no more than 0.01% at 1 kHz and 0.02% at 20 kHz with a +4 dBu output signal. It shall have a dynamic range of 95 dBA and 93 dB unweighted. Maximum output level shall be +24 dBu with a load of 600 ohms or greater. CAB 8o gain shall be from

It shall consume no more than 20 Watts of power and draw no more than 1.4 Amps of current. It shall be supplied with a detachable AC cable and four rubber feet.

It shall be UL, CUL, CE listed and comply with FCC part 15, A. The unit shall be

Peavey Electronics Corp. model CAB 8o.

5

6

ESPA„OL

Descripci—n

Los CAB 8i y CAB 8o respectivamente son puertos MediaMatrix de ocho canales a o de un network Ethernet para distribuci—n y control de audio en tiempo real. Emplean protocolo propietario

CobraNet para asegurar transmisi—n de audio de alta calidad, en tiempo real, limpia y sin errores, sin ca’das (dop-outs) o compresi—n, a travŽs de un network de

Ethernet 100 base T.

El CAB 8i levanta (uploads) ocho canales de audio, ya sean de nivel de l’nea o de micr—fono, an‡logos a un network de Ethernet. Cada canal de entrada cuenta con software para controlar continuamente ganancias an‡logas de -9 dB a +60 dB en pasos de

1 dB. Cada uno cuenta con phantom power de 48 voltios y un pad de reducci—n de 20 dB para micr—fono o l’nea. Las dos funciones son controladas por software.

El CAB 8o baja (downloads) ocho canales de audio a nivel de l’nea de un network Ethernet. Los niveles de salida m‡ximos son individualmente controlados entre +24 dBu, +18 dBu, +12 dBu, y

+6 dBu.

Adem‡s de ocho rutas de entrada o salida, estos dos productos incorporan ocho puertos de entrada controlados por voltaje, ocho puertos de salida TTL controlados por software, ocho relays controlados con software con contactos normalmente abiertos o normalmente cerrados, un puerto RS-485 con conectores multi-drop, y dos relojes wordclock encadenando conectores BCN.

Caracter’sticas

¥ Ocho canales de audio con nivel de micr—fono o l’nea transmitidos a un network Ethernet usando protocolo

CobraNet sampleando a 48 kHz

(CAB 8i).

¥ Ocho canales de audio a nivel de l’nea transmitidos de un network Ethernet usando protocolo CobraNet sampleando a 48 kHz (CAB 8o).

¥ Convertidores A/D de 24 bits, oversampleo de 64x, usando modulaci—n delta-sigma (CAB 8i).

¥ Convertidores D/A de 24 bits, oversampleo de 128 x, usando modulaci—n delta-sigma (CAB 8o)

¥ Phantom power de 48 voltios para entradas de micr—fono, individualmente seleccionables por medio de software para cada canal de entrada (CAB 8i).

¥ Cuantificaci—n (quantization) de 24- o

20- bits con sampleo de 48 kHz.

¥ Ocho canales con puertos de entrada an‡logos de voltaje que permiten controles externos, potenci—metros, o fuentes de voltaje para controlar los par‡metros del software del

MediaMatrix v’a un network Ethernet.

¥ Ocho canales de puerto de salida de control TTL que pueden ser controlados por medio de software v’a conexi—n

Ethernet.

¥ Ocho relays, seleccionables a contactos normales abiertos o normales cerrados, que permiten ser controlados por software de control accesible por medio de unidades externas v’a un network

Ethernet.

¥ Un puerto de control no-Ethernet RS-

485 con dos conexiones multi-drop.

¥ Dos conectores de word-clock que permiten el cambio autom‡ticos a una segunda unidad si la primera fallara.

¥ Chasis de una unidad de rack (1-3/4") con ventilador.

Aplicaciones

¥ Estadios

¥ Barcos de crucero

¥ Locales multi-prop—sito

¥ Auditorios

¥ Sistemas de voceo a gran escala

¥ Escuelas

¥ Cortes

¥ Edificios de universidades

¥ Parques recreativos

¥ Centros de artes escŽnicas

¥ Aprendizaje a distancia

¥ Salones de conferencias de hoteles

¥ Centros religiosos

¥ Centros de conferencias

¥ Teleconferencing

¥ Snakes para micr—fonos de sonorizaci—n

¥ Centros c’vicos

¥ Centros nocturnos

¥ Teatros

¥ Arenas

¥ Cualquier local que requiera distribuci—n de mœltiples micr—fonos o se–ales de nivel de l’nea.

Especificaciones de Audio

Canales de Audio:

CAB 8i: Ocho canales de entrada, nivel de l’nea o micr—fono con opci—n de phantom power de 48 voltios.

CAB 8o: Ocho canales de salida, nivel de l’nea con jumpers individuales para salida m‡xima de +6, +12, +18 o

+24 dBu (el preset de fabrica es

+12 dBu para ganancia I/0).

Nota: Vea especificaciones digitales,

Canales de Audio, para limitaciones en el numero de canales.

Repuesta de Frecuencias:

20 Hz - 20 kHz, +0/-0.5 dB con se–al de entrada de +4 dBu, ganancia de unidad in y out*.

Distorsi—n Arm—nica Total (Total

Harmonic Distortion)

0.01% @ 1 Khz, 0.02% @ 20 kHz con se–al de entrada de +4 dBu, ganancia de unidad in y out*.

Nota: Estas medidas son tomadas usando un filtro de entrada de 10 Hz a

30 kHz con prueba tipo Audio Presicion

One.

Rango Din‡mico:

Nivel de micr—fono:

Ruido de entrada equivalente a

-123 dBu con 150 Ohm, se–al de entrada a -48 dBu, sin pad, ganancia de entrada a 60 dB, ganancia digital a 0 dB, salida an‡loga a +12 dBu m‡xima (jumper preset de f‡brica para ganancia unitaria).

Nota: Esto es equivalente a 78 dBA,

75 dB unweighted.

Nivel de l’nea:

95 dBA, 93 dB unweighted, con se–al de entrada de +12 dBu, ganancia de unidad in y out*.

Entrada CMRR (CAB 8i)

Mejor que 65 dB en cualquier selecci—n:

75 dB con +12 dBu de entrada y ganancia de unidad in y out*, 69 dB con se–al de entrada de +4 dBu y ganancia de unidad in y out*, 68 dB con se–al de entrada de +56 dBu, sin pad, ganancia de entrada an‡loga a 60 dB, ganancia digital a 0, salida an‡loga a +12 dBu m‡xima (jumper preset de f‡brica para ganancia de unidad thourough-put).

Nivel M‡ximo de Entrada (CAB 8i):

+29 dBu, con pad de 20 dB y la ganancia de entrada an‡loga a 0 dB,

+38 dBu con pad de 20 dB y la ganancia de entrada an‡loga a -9 dB.

Nota: El control de la ganancia an‡loga no se ve afectado con un amplificador electr—nicamente balanceado, y mantiene un circuito de entrada balanceado con precisi—n de 1-dB-porpaso y CMRR especificado.

7

Nivel M‡ximo de Salida (CAB 8o):

+24 dBu @ 600 ohmios.

Ganancia del CAB 8i:

Ganancia an‡loga controlada por software de -9 dB a +60 dB, ajustable en incrementos de 1 dB con switch para seleccionar entrada de l’nea o micr—fono por medio de software. (La selecci—n de entrada de nivel inserta un pad de

20 dB).

Ganancia del CAB 8o:

Ganancia an‡loga controlada por software de -95.5 dB a +31.5 dB, ajustable en incrementos de 0.5 dB con jumpers internos an‡logos para m‡ximos niveles de salida de +6,

+12, +18, o +24 dBu.

Nota: No es recomendable usar esto como nivel de salida de micr—fono, ya que el ruido se convertir‡ en un problema en niveles extremadamente bajos de salida.

Impedancia de Entrada (CAB 8i):

22.2 K ohmios por entrada de l’nea y

2.2 k ohmios por entrada de micr—fono.

Impedancia de Salida (CAB 8o):

100 ohmios, dise–ado para manejar un m’nimo de 600 ohmios.

Medidores An‡logos LED:

Ocho medidores tipo peak, calibrados en dBu, monitorean el nivel de se–al an‡loga presente en la entrada de los convertidores A/D del CAB 8i, y en la salida de los convertidores D/A del CAB

8o, donde el LED rojo superior indica saturaci—n o distorsi—n A/D o D/A.

Nota: El LED rojo superior nunca debe encenderse bajo condiciones de uso normal.

Nota 1: Las especificaciones de audio son medidas de la entrada al CAB 8i y la salida del CAB 8o donde relevante.

Nota 2: Todas las especificaciones son t’picas.

*Indica sin pad de entrada, ganancia de entrada an‡loga a 0 dB, ganancia digital a

0 dB, Salida an‡loga a +12 dBu m‡ximo

(Jumper de fabrica para ganancia unitaria though-put).

Especificaciones Digitales

Cuantificaci—n A/D y D/A

(quantization):

Resoluci—n de 24-bits

Cuantificaci—n de Transmisi—n de

Audio v’a CobraNet:

Controlada por software, resoluci—n de

24 o 20-bits.

Procesos Digitales (Digital

Processing):

DSP de 24-bit, acumuladores de 56-bit

Velocidades de Sampleo de Audio y de Reloj:

Sampleo de audio a 48 kHz, DSP a

80 MHz y reloj maestro a 12.288 MHz.

Canales de Audio por CAB 8i/8o:

Ocho con cuantificaci—n seleccionada a

20-bit.

Siete con cuantificaci—n seleccionada a

24-bit.

Especificaciones de Control

CobraNet I/O:

100 Base T Ethernet v’a conexi—n eight-conductor est‡ndar RJ-45.

RS-485:

Un puerto con dos Conectores 3-cond.

medio duplex, multi-drop.

Puertos de Control:

Control de Entrada de Voltaje:

0 VDC a +10 VDC, con potenci—metros externos o fuentes de control de voltaje externas (una fuente interna de 10 VCD es proporcionada).

Salidas TTL (Transistor-to-Transistor

Logic) Controladas por Software:

0 VDC — +5 VDC, con corriente m‡xima de 28 mA distribuida a ocho salidas.

Ocho Relays Controlados por

Software Con contacto NO y NC:

Voltaje M‡ximo de Contacto:

120 VAC o DC

Corriente M‡xima de Contacto:

2 A

Puertos Word-clock:

Dos puertos I/O BCN

Nota: Pueden ser usados como seguro ya que si hay dos CAB 8 conectados en serie, el segundo funcionar‡ en cuanto el primero tenga un problema.

ESPECIFICACIONES

GENERALES:

Dimensiones:

CAB 8i CAB 8o:

1.730" Alto x 19" Ancho x 11.6980

Profundo.

(4.39 cm x 48.26 cm x 29.71 cm)

Peso Neto:

CAB 8i: 8.5 lbs (3.86 kg.)

CAB 8o: 8.4 lbs (3.81 kg.)

Poder CA:

Fuente de poder Universal:

1.4 A m‡ximo, 100 a 200 VAC, 47 a

63 Hz.

8

Consumo de energ’a y generaci—n de calor:

CAB 8i: 25 W, 85 BTU/Hr

CAB 8o: 20 W, 68 BTU/Hr

M‡xima Corriente In-Rush:

CAB 8i y CAB 8o: menos de 1.4 Amps.

Terminado:

Acero pintado gris

Accesorios:

Un cable removible de poder (AC), cuatro adhesivos pies de hule.

Cumple los requisitos de las siguientes agencias:

UL, CUL, CE FCC parte 15, A

ESPECIFICACIONES PARA

ARQUITECTOS E INGENIEROS

Las especificaciones de audio, cuando relevantes, son medidas con la entrada alimentando al CAB 8i, transmitido digitalmente por un centro (hub) Ethernet, y la salida del CAB 8o.

CAB 8i:

El CAB 8i de Peavey debe transmitir ocho canales de nivel micr—fono o l’nea a un network Ethernet. Debe proporcionar un rango completo, y transmisi—n de audio de alta calidad v’a Ethernet 100Base T (fast), sin tŽcnicas nefastas de compresi—n, drop-outs o degradaci—n de se–al. Para esto se emplea el protocolo de transmisi—n de audio CobraNet, haciendo la distribuci—n de se–al por Ethernet determinante. Debe emplear convertidores A/D de 24-bit, con cuantificaci—n de transmisi—n seleccionable a 24 o 20-bit usando velocidad de sampleo de 48 kHz.

Debe tener una respuesta de frecuencias de 20 Hz a 20 kHz, +0/-0.5 dB o mejor.

Su total distorsi—n arm—nica (THD) no debe sobrepasar 0.01% a 1 kHz, y 0.02% a 20 kHz con una se–al de entrada de 4 dBu.. Debe tener un rango din‡mico de

95 dBA y 93 dB unweighted para entradas de nivel de l’nea, y un ruido de entrada equivalente a -124 dB para se–ales de nivel de micr—fono. El inputcommon-mode-rejection ratio (CMRR) debe ser mayor que 65 dB en cualquier selecci—n. El nivel m‡ximo de entrada antes de saturaci—n debe ser +38 dBu manteniendo el CMRR especificado. La ganancia de entrada del CAB 8i debe ser de -9 dB a +60 dB en pasos de 1 dB. La impedancia de entrada del CAB 8i debe ser 2.2 k ohmios en nivel de micr—fono

(sin pad de 20 dB), y 22.2 k ohmios en nivel de l’nea (con pad de 20 dB).

Las caracter’sticas de los controles deben incluir ocho relays con contactos tanto normales abiertos como normales cerrados, y ocho canales de control de salida TTL, los dos controlables por software v’a conexi—n Ethernet. TambiŽn se incluyen ocho canales de control de voltaje que permiten la existencia de switches externos, potenciometros o fuentes de voltaje para controlar los par‡metros del software del MediaMatrix v’a una conexi—n Ethernet.

Los indicadores del panel frontal deben indicar las condiciones siguientes: transmisi—n de se–al, recepci—n de se–al, error de transmisi—n, error de recepci—n, indicador de falla, indicador de conexi—n

(link), estado de conductor, indicador de control RS-485 y presencia de poder.

Debe tener ocho medidores de nivel tipo peak para monitorear el nivel an‡logo presente en la entrada de los convertidores A/D, donde el LED rojo superior indica clipping.

El panel trasero debe incluir un cable de corriente (AC) que se puede quitar, un switch de encendido, un control de poder con un circuito de seguridad (breaker) autom‡tico integrado. Los fusibles internos o externos no deben ser aceptados. Debe incluir dos conectores para word-clock para permitir que entre en acci—n una segunda unidad en caso que la primera falle. Debe emplear conectores modulares, tipo euro-style para facilitar las conexiones y reparaciones. Estos conectores deben ser usados para todas las conexiones de nivel de l’nea, nivel de micr—fono, control de voltaje, TTL, relays y

RS-485. La unidad debe usar una conexi—n Ethernet est‡ndar de ocho conductores RJ-45 I/O.

Sus dimensiones deben ser 19 pulgadas

(48.26 cm) de ancho, 12 7/8 pulgadas

(32.70 cm), y 1 3/4 pulgadas (4.44 cm) de alto sin pies. Su peso neto debe ser 8.5

libras (3.86 kg.), y el chasis de una unidad de rack (1 3/4"), enfriado por ventilador, debe estar terminado con pintura gris.

No debe consumir m‡s de 25 Watts de poder y tomar m‡s de 1.4 Amps de corriente. Debe incluir un cable removible de poder (AC) y cuatro pies de pl‡stico.

Debe estar en las listas de UL, CUL, CE y llenar los requisitos de la FCC parte 15, A.

La unidad debe ser Peavey Electronics

Corporation modelo CAB 8i.

CAB 8o

El CAB 8o de Peavey debe recibir ocho canales de nivel de l’nea transmitidos por un network Ethernet. Debe proporcionar un rango completo, y transmisi—n de audio de alta calidad v’a Ethernet 100Base T

(fast), sin tŽcnicas nefastas de compresi—n, drop-outs o degradaci—n de se–al. Para esto se emplea el protocolo de transmisi—n de audio CobraNet, haciendo la distribuci—n de se–al por

Ethernet determinante. Debe emplear convertidores A/D de 24-bit, con cuantificaci—n de transmisi—n seleccionable a 24 o 20-bit usando velocidad de sampleo de 48 kHz.

Debe tener una respuesta de frecuencias de 20 Hz a 20 kHz, +0/-0.5 dB o mejor.

Su total distorsi—n arm—nica (THD) no debe sobrepasar 0.01% a 1 kHz, y 0.02% a 20 kHz con una se–al de entrada de

4 dBu.. Debe tener un rango din‡mico de

95 dBA y 93 dB unweighted. El nivel m‡ximo de salida debe ser +24 dBu con carga de 600 ohmios o mayor. La ganancia del CAB 8o debe restar entre

-95.5 dB a +31.5 dB en pasos de 0.5 dB.

La impedancia de salida del CAB 8o debe ser de 100 ohmios y dise–ada para manejar una carga de 600 ohmios o mayor.

Las caracter’sticas de los controles deben incluir ocho relays con contactos tanto normales abiertos como normales cerrados, y ocho canales de control de salida TTL, los dos controlables por software v’a conexi—n Ethernet. TambiŽn se incluyen ocho canales de control de voltaje que permiten la existencia de switches externos, potenciometros o fuentes de voltaje para controlar los par‡metros del software del MediaMatrix v’a una conexi—n Ethernet.

Los indicadores del panel frontal deben indicar las condiciones siguientes: transmisi—n de se–al, recepci—n de se–al, error de transmisi—n, error de recepci—n, indicador de falla, indicador de conexi—n

(link), estado de conductor, indicador de control RS-485 y presencia de poder.

Debe tener ocho medidores de nivel tipo peak para monitorear el nivel an‡logo presente en la entrada de los convertidores D/A, donde el LED rojo superior indica saturaci—n.

El panel trasero debe incluir un cable de corriente (AC) que se puede quitar, un switch de encendido, un control de poder con un circuito de seguridad (breaker) autom‡tico integrado. Los fusibles internos o externos no deben ser aceptados. Debe incluir dos conectores para word-clock para permitir que entre en acci—n una segunda unidad en caso que la primera falle. Debe emplear conectores modulares, tipo euro-style para facilitar las conexiones y reparaciones. Estos conectores deben ser usados para todas las conexiones de nivel de l’nea, control de voltaje, TTL, relays y RS-485. La unidad debe usar una conexi—n Ethernet est‡ndar de ocho conductores RJ-45 I/O.

Sus dimensiones deben ser 19 pulgadas

(48.26 cm) de ancho, 12 7/8 pulgadas

(32.70 cm), y 1 3/4 pulgadas (4.44 cm) de alto sin pies. Su peso neto debe ser 8.4

libras (3.81 kg.), y el chasis de una unidad de rack (1 3/4"), enfriado por ventilador, debe estar terminado con pintura gris.

No debe consumir m‡s de 20 Watts de poder y tomar m‡s de 1.4 Amps de corriente. Debe incluir un cable removible de poder (AC) y cuatro pies de pl‡stico.

Debe estar en las listas de UL, CUL, CE y llenar los requisitos de la FCC parte 15, A.

La unidad debe ser Peavey Electronics

Corporation modelo CAB 8o.

9

FRAN‚AIS

Description

Les modules CAB 8i CAB 8o sont des passerelles MediaMatrix ˆ huit entrŽes et huit sorties, respectivement, permettant de communiquer avec un rŽseau Ethernet pour la distribution et le contr™le audio en temps rŽel dÕun poste MediaMatrix. Ils emploient le protocole exclusif CobraNet pour assurer la transmission sans coupures ni erreurs de signaux audio de haute qualitŽ sans pertes de compression ni Žvanouissement de la transmission, au travers dÕun rŽseau Ethernet 100baseT.

Le CAB 8i permet de tŽlŽcharger huit canaux de signaux audio analogiques de niveau microphone ou ligne sur un rŽseau

Ethernet. Chaque canal dÕentrŽe offre un rŽglage de gain analogique continu de -9 dB ˆ +60 dB, par incrŽments de 1 dB, contr™lŽ par logiciel. Chaque canal est dotŽ dÕune alimentation duplex de 48 volts et dÕun attŽnuateur de niveau ligne/micro de 20 dB. Les deux fonctions peuvent •tre commutŽes par logiciel.

Le CAB 8o permet de tŽlŽcharger huit canaux de signaux analogiques de niveau ligne ˆ partir dÕun rŽseau Ethernet. Les niveaux maximum de sortie peuvent •tre rŽglŽs individuellement ˆ +24 dBu, +18 dBu, +12 dBu, et +6 dBu par positionnement des cavaliers.

Outre les huit entrŽes ou sorties de signaux audio, les deux produits offrent huit ports dÕentrŽe de contr™le de tension, huit ports de sortie TTL contr™lŽs par logiciel, huit relais contr™lŽs par logiciel avec contacts normalement ouverts et normalement fermŽs, un port RS-485 avec connexions multipoints et deux connecteurs BNC pour liaison word-clock.

Fonctions

¥ Huit canaux audio de niveau ligne ou microphone transmis ˆ un rŽseau

Ethernet au moyen du protocole

CobraNet ŽchantillonnŽ ˆ 48 kHz

(CAB 8i).

¥ Huit canaux dÕaudio de niveau ligne transmis ˆ partir dÕun rŽseau Ethernet au moyen du protocole CobraNet

ŽchantillonnŽ ˆ 48 kHz (CAB 8o).

¥ Convertisseurs A/N 24 bits, surŽchantillonnage 64 fois, utilisant la modulation delta-sigma (CAB 8i).

¥ Convertisseurs N/A 24 bits, surŽchantillonnage 128 fois, utilisant la modulation delta-sigma (CAB 8o).

¥ Alimentation duplex 48 volts pour entrŽes microphone, commutŽ par logiciel sur chaque canal dÕentrŽe

(CAB 8i).

¥ Quantification de transmission 24 ou 20 bits ˆ une vitesse dÕŽchantillonnage de

48 kHz.

¥ Huit ports dÕentrŽe de tension de commande analogique permettant lÕusage de commutateurs, potentiom•tres ou sources de tension pour contr™ler les param•tres de logiciel

MediaMatrix via une liaison Ethernet.

¥ Huit sorties de commande TTL pouvant

•tre contr™lŽes par logiciel via une liaison Ethernet.

¥ Huit relais avec contacts normalement ouverts et normalement fermŽs permettant la commande par logiciel de dispositifs externes via une liaison

Ethernet.

¥ Un port de commande RS-485 non

Ethernet avec deux connexions multipoints.

¥ Deux connecteurs de liaison word-clock permettant la commutation automatique

ˆ un second module en cas de dŽfaillance du premier.

¥ Ch‰ssis ˆ simple espace de rack de

44,5 mm (1 3/4 po), refroidi par ventilateur.

la puissance de sortie maximum de chaque canal ˆ +6, +12, +18 ou +24 dBu

(le rŽglage par dŽfaut est +12 dBu pour un gain unitaire dÕE/S).

Remarque: Voir Nombre de canaux audio par CAB 8i/8o, ˆ la rubrique

CaractŽristiques numŽriques pour les limites de nombre des canaux.

RŽponse en frŽquence:

20 Hz ˆ 20 kHz, +0/-0,5 dB, avec un signal dÕentrŽe de +4 dBu, gain unitaire dÕentrŽe et sortie.*

Distorsion harmonique total:

0,01 % ˆ 1kHz, 0,02 % ˆ 20 kHz, avec un signal dÕentrŽe de +4 dBu, gain unitaire dÕentrŽe et sortie.*

Remarque: Mesures prises avec un filtre dÕentrŽe de 10 Hz ˆ 30 kHz sur le syst•me de prŽcision audio un aux fins de test.

Applications

¥ Stades

¥ Navires de croisi•re

¥ Locaux publics

¥ Auditoriums

¥ Syst•mes de tŽlŽappel ˆ grande Žchelle

¥ ƒcoles

¥ Tribunaux

¥ B‰timents universitaires

¥ Parcs ˆ th•me

¥ Centres des arts du spectacle

¥ Enseignement ˆ distance

¥ Salles de rŽunions dÕh™tels

¥ Maisons de culte

¥ Centres de confŽrences

¥ TŽlŽconfŽrence

¥ Multic‰bles de sonorisation

¥ Centres municipaux

¥ Clubs de musique

¥ ThŽ‰tres

¥ Ar•nes

¥ Toute installation exigeant la distribution de multiples signaux de niveau ligne ou microphone

Dynamique de modulation:

Niveau micr :

Bruit dÕentrŽe Žquivalent -123 dBu, avec un signal dÕentrŽe de 150 ohms, -48 dBu, pas dÕattŽnuateur dÕentrŽe, un gain dÕentrŽe analogique rŽglŽ ˆ 60 dB, un gain numŽrique de 0 dB, la sortie analogique rŽglŽe ˆ +12 dB (position de cavalier par dŽfaut pour un gain unitaire dÕE/S). Remarque: ceci Žquivaut ˆ

78 dBA, 75 dB, non pondŽrŽ.

Niveau ligne:

95 dBA, 93 dB non pondŽrŽ, avec un signal dÕentrŽe de +12 dBu, gain unitaire dÕentrŽe et sortie.*

RRMC dÕentrŽe (CAB 8i):

SupŽrieur ˆ 65 dB, quel que soit le rŽglage de gain:

73 dB avec entrŽes +12 dB et gain unitaire dÕentrŽe et sortie*, 69 dB avec un signal dÕentrŽe de +4 dBu et gain unitaire dÕentrŽe et sortie*, 68 dB avec un signal dÕentrŽe de -56 dBu, pas dÕattŽnuateur dÕentrŽe, un gain dÕentrŽe analogique rŽglŽ ˆ 60 dB et un gain de sortie analogique rŽglŽ pour +12 dBu maximum (position de cavalier par dŽfaut pour un gain unitaire dÕE/S).

CARACTƒRISTIQUES AUDIO

Canaux audio :

CAB 8i: Huit canaux dÕentrŽe niveau ligne ou microphone avec alimentation duplex 48 volts commutable.

CAB 8o: Huit canaux de sortie niveau ligne avec cavaliers permettant de rŽgler

Niveau dÕentrŽe maximum (CAB 8i):

+29 dBu, avec attŽnuation 20 dB et gain dÕentrŽe analogique rŽglŽ ˆ 0 dB, +38 dBu avec attŽnuation 20 dB et gain dÕentrŽe analogique ˆ -9 dB.

Remarque: La commande de gain dÕentrŽe analogique nÕest pas sŽparŽe par un amplificateur tampon ŽquilibrŽ

10

Žlectroniquement et maintient un circuit dÕentrŽe symŽtrique avec prŽcision dÕincrŽments de 1 dB et RRMC spŽcifiŽ.

CARACTƒRISTIQUES

NUMƒRIQUES

Niveau de sortie maximum (CAB 8o):

+24 dBu ˆ 600 ohms

Quantification A/N et N/A:

RŽsolution 24 bits

Gain CAB 8i:

Gain analogique contr™lŽ par logiciel de

-9 ˆ +60 dB, rŽglable par incrŽments de

1 dB, avec commutateur dÕentrŽe analogique micro/ligne contr™lŽ par logiciel (lorsque le niveau ligne est sŽlectionnŽ, une attŽnuation de 20 dB est appliquŽe).

Quantification de transmission audio via CobraNet :

RŽsolution 24 ou 20 bits, sŽlectionnŽe par logiciel

Traitement numŽrique:

Processeur numŽrique 24 bits, accumulateurs de 56 bits

Gain CAB 8o:

Gain de sortie analogique contr™lŽ par logiciel de -95,5 ˆ +31,5 dB, rŽglable par incrŽments de 0,5 dB au moyen des cavaliers de sortie analogique internes pour des niveaux de sortie maximum de

+6, +12, +18 ou +24 dBu.

Remarque: LÕutilisation comme sortie de niveau microphone nÕest pas recommandŽe car le bruit est un probl•me ˆ des niveaux de sortie extr•mement bas.

ImpŽdance dÕentrŽe (CAB 8i):

22,2 Kohms pour le niveau dÕentrŽe ligne et 2,2 Kohms pour le niveau dÕentrŽe microphone.

Vitesse dÕŽchantillonnage audio et dÕhorloge:

ƒchantillonage audio 48 kHz, processeur numŽrique 80 mHz, horloge centrale

12,288 mHz

Nombre de canaux audio par CAB

8i/8o:

¥ Huit lorsque la quantification de transmission 20 bits est sŽlectionnŽe

¥ Sept lorsque la quantification de transmission 24 bits est sŽlectionnŽe

CaractŽristiques de commande

E/S CobraNet:

Ethernet 100BaseT via jack RJ-45 ˆ 8 conducteurs standard

ImpŽdance de sortie (CAB 8o):

100 ohms, con•ue pour piloter une charge minimum de 600 ohms.

RS-485:

Un port avec deux connexions multipoints semi-duplex 3 cond.

Vu-m•tres analogiques ˆ DEL:

Huit vu-m•tres avec indication de marge de sŽcuritŽ/Žcr•tage, graduŽs en dBu permettent de surveiller le niveau de signal analogique prŽsent ˆ lÕentrŽe des convertisseurs A/N du module CAB 8i, et

ˆ la sortie des convertisseurs N/A du module CAB 8o, la DEL rouge supŽrieure indiquant lÕŽcr•tage A/N ou

N/A.

Remarque: La DEL rouge supŽrieure ne doit jamais sÕallumer pendant le fonctionnement normal.

Ports de commande:

EntrŽe de tension de commande :

0 ˆ 10 V c.c., commandŽe par potentiom•tre ou sources de tension externe (tension 10 V c.c. interne fournie)

Sortie TTL (logique transistor/transistor) contr™lŽe par logiciel:

0 ou +5 V c.c. avec une intensitŽ maximum de 28 mA rŽpartie sur 8 sorties

Remarque 1: Lorsque nŽcessaire, les caractŽristiques audio ont ŽtŽ mesurŽes ˆ lÕentrŽe du module CAB 8i et ˆ la sortie du module CAB 8o.

Remarque 2: Toutes les caractŽristiques sont typiques.

*Indique lÕabsence dÕattŽnuateur dÕentrŽe, un gain dÕentrŽe analogique de 0 dB, un gain numŽrique de 0 dB, une sortie analogique rŽglŽe ˆ +12 dB (position de cavalier par dŽfaut pour un gain unitaire dÕE/S).

Huit relais contr™lŽs par logiciel avec contacts N/O et N/F:

Tension maximum de contact:

120 V c.a. ou c.c.

IntensitŽ maximum de contact:

2 A

Ports word-clock :

Deux ports BNC dÕE/S

Remarque: Ces ports peuvent •tre utilisŽs pour la sŽcuritŽ redondante afin de passer dÕun CAB 8 ˆ un autre en cas de dŽfaillance du premier.

CARACTƒRISTIQUES

GƒNƒRALES

Dimensions:

CAB 8i CAB 8o:

H 4,39 x L 48,26 x P 29,71 cm

(1,730 x 19 x 11,698 po)

Poids net:

CAB 8i: 3,86 kg (8,5 lb)

CAB 8o: 3,81 kg (8,4 lb)

Alimentation c.a.:

Alimentation universelle:

1,4 A maximum, 100 ˆ 240 V c.a., 47

ˆ 63 Hz

Consommation de courant et dŽgagement de chaleur:

CAB 8i: 25 W, 85 BTU/Hr

CAB 8o: 20 W, 68 BTU/Hr

IntensitŽ maximum de courant dÕappel:

CAB 8i et CAB 8o: moins de 1,4 A

Finition:

Acier ˆ rev•tement ˆ poudrage gris

Accessoires:

Cordon c.a. amovible, quatre pieds adhŽsifs en caoutchouc

ConformitŽ aux rŽglementations

Homologations

UL, ULC, CE FCC part 15, A

SPƒCIFICATIONS

DÕARCHITECTURE ET

INGƒNIERIE

Les spŽcifications audio sont mesurŽes avec le signal dÕentrŽe entrant dans le

CAB 8i, transmis numŽriquement via rŽseau Ethernet et le signal de sortie sortant du CAB 8o, le cas ŽchŽant.

CAB 8i:

Le Peavey CAB 8i devra offrir huit canaux audio de niveau ligne ou microphone transmis sur un rŽseau Ethernet. Il devra assurer une transmission audio pleine bande de haute qualitŽ via Ethernet

100BaseT (rapide) sans techniques de perte de compression, Žvanouissement de transmission ou dŽgradation du signal par utilisation dÕun protocole de transmission audio CobraNet, rendant la distribution du signal Ethernet dŽterministe.

11

Il devra utiliser des convertisseurs A/N 24 bits avec quantification de transmission sŽlectionnable 20 ou 24 bits avec un taux dÕŽchantillonnage de 48 kHz.

Sa rŽponse en frŽquence devra •tre de 20

Hz ˆ 20 kHz, +0/-0,5 dB ou mieux. Sa distorsion harmonique totale devra •tre de

0,01% maximum ˆ 1 kHz et 0,02% avec un signal dÕentrŽe de +4 dBu. Il devra prŽsenter une modulation dynamique de

95 dBa et 93 dB non pondŽrŽe pour les signaux de niveau ligne et un niveau de bruit Žquivalent de -124 dB pour les signaux de niveau microphone. Le rapport de rŽjection en mode commun (RRMC) devra •tre supŽrieur ˆ 65 dB, quel que soit le rŽglage de gain. Le niveau maximum dÕentrŽe sans Žcr•tage devra

•tre de +38 dBu tout en maintenant le

RRMC spŽcifiŽ. Le gain dÕentrŽe du CAB

8i devra •tre compris entre -9 dB et

+60 dB par incrŽments de 1 dB.

LÕimpŽdance dÕentrŽe du CAB 8i devra

•tre de 2,2 Kohms au niveau microphone

(sans attŽnuation 20 dB), et 22,2 Kohms au niveau ligne (avec attŽnuation 20 dB).

Les fonctions de commande devront inclure huit relais ˆ contacts normalement ouverts et normalement fermŽs, et huit canaux de sortie de commande TTL, ces deux fonctions pouvant •tre contr™lŽes par logiciel via une liaison Ethernet. Il devra Žgalement inclure huit ports dÕentrŽe de tension de commande analogique permettant lÕusage de commutateurs, potentiom•tres ou sources de tension pour contr™ler les param•tres de logiciel MediaMatrix via une liaison

Ethernet.

Les tŽmoins du panneau avant devront indiquer les Žtats suivants : transmission de signal, rŽception de signal, erreur de transmission, erreur de rŽception, indication de dŽfaut, indication de liaison,

Žtat des conducteurs, indication de commande RS-485 et prŽsence dÕalimentation. Il devra comporter huit vum•tres indicateurs de marge de sŽcuritŽ permettant de surveiller le niveau de signal analogique prŽsent ˆ lÕentrŽe des convertisseurs A/N, la DEL rouge supŽrieure indiquant un Žcr•tage A/N.

Le panneau arri•re devra comporter un connecteur pour cordon dÕalimentation c.a.

amovible, un commutateur de mise sous tension, et une prise de courant c.a. dotŽe dÕun disjoncteur ˆ rŽarmement automatique. Les fusibles internes ou externes ne seront pas acceptables. Il devra comporter deux connecteurs wordclock permettant la commutation automatique en cas de dŽfaillance dÕun module. Il devra utiliser des connecteurs ˆ vis pour fils dŽnudŽs amovibles de type europŽen pour faciliter les branchements et le dŽpannage. Ces connecteurs devront

•tre utilisŽs pour tous les branchements de signal niveau ligne, niveau microphone, tension de commande, TTL, relais et connexion RS-485. LÕappareil devra utiliser un jack dÕE/S RJ-45 huit conducteurs standard pour le raccordement ˆ un rŽseau Ethernet.

Les dimensions devront •tre de 48,26 cm

(19 po) de largeur, 32,70 cm (12 7/8) de profondeur et 4,44 cm (1 3/4 po) de hauteur, sans les pieds. Le poids net devra •tre de 3,86 kg (8,5 lb) et son ch‰ssis en acier ˆ simple espace de rack

(4,44 cm) refroidi par ventilateur devra

•tre rev•tu dÕune peinture ˆ poudrage grise.

Il ne devra pas consommer plus de 25 watts ni tirer plus de 1,4 A. Il devra •tre accompagnŽ dÕun cordon dÕalimentation c.a. amovible et de quatre pieds en caoutchouc. Il devra •tre homologuŽ UL,

ULC et CE, et •tre conforme ˆ la section

15 A des rŽglementations de la FCC.

LÕunitŽ sera le mod•le CAB 8i de Peavey

Electronics Corporation.

CAB 8o :

Le Peavey CAB 8o devra offrir huit canaux de signal audio de niveau ligne transmis ˆ partir dÕun rŽseau Ethernet. Il devra assurer une transmission audio pleine bande de haute qualitŽ via Ethernet

100BaseT (rapide) sans techniques de pertes de compression, Žvanouissement de transmission ou dŽgradation du signal par utilisation dÕun protocole de transmission audio CobraNet, rendant le rŽseau Ethernet dŽterministe. Il devra utiliser des convertisseurs A/N 24 bits avec quantification de transmission sŽlectionnable 20 ou 24 bits utilisant un taux dÕŽchantillonnage de 48 kHz.

Sa rŽponse en frŽquence devra •tre de 20

Hz ˆ 20 kHz, +0/-0,5 dB ou mieux. Sa distorsion harmonique totale devra •tre de

0,01 % maximum ˆ 1 kHz et de 0,02 % ˆ

20 kHz avec un signal de sortie de

+4 dBu. Il devra prŽsenter une modulation dynamique de 95 dBA et 93 dB non pondŽrŽe. Le niveau maximum de sortie devra •tre de +24 dBu avec une charge de 600 ohms ou plus. Le gain du CAB 8o devra •tre de Ñ95,5 dB ˆ +31,5 dB en incrŽments de 0,5 dB. LÕimpŽdance de sortie du CAB 8o devra •tre de 100 ohms et con•ue pour piloter une charge de 600 ohms ou plus.

Les fonctions de commande devront inclure huit relais ˆ contacts normalement ouverts et normalement fermŽs, et huit canaux de sortie de commande TTL, ces deux fonctions pouvant •tre contr™lŽes par logiciel via une liaison Ethernet. Il devra Žgalement inclure huit ports dÕentrŽe de tension de commande analogique permettant lÕusage de commutateurs, potentiom•tres ou sources de tension pour contr™ler les param•tres de logiciel MediaMatrix via une liaison

Ethernet.

Les tŽmoins du panneau avant devront indiquer les Žtats suivants : transmission de signal, rŽception de signal, erreur de transmission, erreur de rŽception, indication de dŽfaut, indication de liaison,

Žtat des conducteurs, indication de commande RS-485 et prŽsence dÕalimentation. Il devra comporter huit vum•tres indicateurs de marge de sŽcuritŽ permettant de surveiller le niveau de signal analogique prŽsent ˆ la sortie des convertisseurs N/A, la DEL rouge supŽrieure indiquant un Žcr•tage N/A.

Le panneau arri•re devra comporter un connecteur pour cordon dÕalimentation c.a.

amovible, un commutateur de mise sous tension, et une prise de courant c.a. dotŽe dÕun disjoncteur ˆ rŽarmement automatique. Les fusibles internes ou externes ne seront pas acceptables. Il devra comporter deux connecteurs wordclock permettant la commutation automatique en cas de dŽfaillance dÕun module. Il devra utiliser des connecteurs ˆ vis pour fils dŽnudŽs amovibles de type europŽen pour faciliter les branchements et le dŽpannage. Ces connecteurs devront

•tre utilisŽs pour tous les branchements de signal niveau ligne, tension de commande, TTL, relais et connexion RS-

485. LÕappareil devra utiliser un jack dÕE/S

RJ-45 ˆ huit conducteurs standard pour le raccordement ˆ un rŽseau Ethernet.

Les dimensions devront •tre de 48,26 cm

(19 po) de largeur, 32,70 cm (12 7/8) de profondeur et 4,44 cm (1 3/4 po) de hauteur, sans les pieds. Le poids net devra •tre de 3,81 kg (8,4 lb) et son ch‰ssis en acier ˆ simple espace de rack

(4,44 cm) refroidi par ventilateur devra

•tre rev•tu dÕune peinture ˆ poudrage grise.

Il ne devra pas consommer plus de 20 watts ni tirer plus de 1,4 A. Il devra •tre accompagnŽ dÕun cordon dÕalimentation c.a. amovible et quatre pieds en caoutchouc. Il devra •tre homologuŽ UL,

ULC et CE, et •tre conforme ˆ la section

15 A des rŽglementations de la FCC.

LÕunitŽ sera le mod•le CAB 8o de Peavey

Electronics Corporation.

12

Beschreibung

CAB 8i und CAB 8o sind MediaMatrix-

Gateways mit jeweils acht Ein- und

AusgŠngen zu bzw. von einem Ethernet-

Netzwerk fŸr die Verteilung und Steuerung von MediaMatrix-Audiosignalen in

Echtzeit. Das proprietŠre CobraNet-

Protokoll sichert die nahtlose und fehlerfreie EchtzeitŸbertragung von

Audiosignalen hoher QualitŠt Ÿber ein

100baseT-Ethernet ohne AusfŠlle und

Kompressionsverluste.

Das CAB 8i lŠdt analoge Mikrofon- oder

Line-Level-Audiosignalen in acht KanŠlen in das Ethernet-Netzwerk. Jeder der

EingangskanŠle bietet eine Ÿber Software gesteuerte, kontinuierlich regelbare analoge VerstŠrkung (Gain) von -9 dB bis

+60 dB in Einzelschritten von je 1 dB. Alle

KanŠle sind 48-V-phantomgespeist und haben ein 20-dB-Mic/Line-

DŠmpfungsglied. Beide Funktionen sind

Ÿber Software schaltbar.

Das CAB 8o lŠdt acht KanŠle mit analogen Line-Level-Audiosignalen aus einem Ethernet-Netzwerk. Die maximalen

Ausgangspegel sind separat Ÿber Jumper wŠhlbar: +24 dBu, +18 dBu, +12 dBu oder

+6 dBu.

Neben den acht Eingangs- bzw.

Ausgangs-Audiowegen verfŸgen beide

Produkte Ÿber acht Spannungsregelungs-

Eingangsports, acht softwaregesteuerte

TTL-Ausgangsports, acht softwaregesteuerte Relais mit Arbeits- und

Ruhekontakten, einen RS-485-Port mit

MehrpunktanschlŸssen und zwei BNC-

Steckverbindungen fŸr Word-Clock-

Linking.

Merkmale

¥ Acht KanŠle Ÿbertragen unter

Verwendung des CobraNet-Protokolls entweder Mikrofon- oder Line-Level-

Audiosignale mit einer Abtastfrequenz von 48 kHz (CAB 8i) auf ein Ethernet-

Netzwerk.

¥ †bertragung von Line-Level-

Audiosignalen aus einem Ethernet-

Netzwerk Ÿber acht KanŠle unter

Verwendung des CobraNetª-Protokolls mit einer Abtastfrequenz von 48 kHz

(CAB 8o).

¥ 24-Bit-A/D-Wandler mit 64-fachem

Oversampling und Delta-Sigma-

Modulation (CAB 8i).

¥ 24-Bit-D/A-Wandler mit 128-fachem

Oversampling und Delta-Sigma-

Modulation (CAB 8o).

¥ 48-V-Phantomspeisung fŸr

MikrofoneingŠnge, in jedem

Eingangskanal separat Ÿber Software schaltbar (CAB 8i).

FRAN‚AIS

¥ 24- oder 20-Bit-†bertragungsquantisierung mit einer Abtastfrequenz von

48 kHz.

¥ Acht KanŠle mit analogen

SteuerspannungseingŠngen fŸr die

Steuerung der MediaMatrix-Software durch externe Schalter, Potentiometer oder Spannungsquellen Ÿber ein

Ethernet-Link.

¥ Acht KanŠle mit TTL-SteuerausgŠngen, die Ÿber ein Ethernet-Link mit Software gesteuert werden kšnnen.

¥ Acht Relais mit sowohl Arbeits- als auch

Ruhekontakten fŸr die

Softwaresteuerung externer

Einrichtungen Ÿber ein Ethernet-Link.

¥ Ein Nicht-Ethernet-RS-485-

Steuerungsport mit zwei

MehrpunktanschlŸssen.

¥ Zwei Word-Clock-Linking-AnschlŸsse zur Umschaltung auf ein redundantes

ZweitgerŠt beim Ausfall des ersten.

¥ Chassis mit LŸfterkŸhlung, eine HE

(44 mm).

E/A-VerstŠrkungsfaktor eins).

Hinweis: Begrenzungen der

Kanalanzahl siehe ãAudiokanŠle CAB

8i/8oÒ unter ãTechnische Daten Ð DigitalÒ

Frequenzgang:

20 Hz bis 20 kHz, +0/-0,5 dB bei

+4 dBu-Eingangssignal, Eingangs-

/Ausgangs-VerstŠrkungsfaktor Eins.*

Gesamtklirrfaktor:

0,01 % bei 1 kHz, 0,02 % bei 20 kHz, gilt fŸr +4 dBu-Eingangssignal, Eingangs-

/Ausgangs-VerstŠrkungsfaktor Eins.*

Hinweis: Messungen wurden mit einem

10 Hz bis 30 kHz-Eingangsfilter in einem

Audio Precision System One durchgefŸhrt.

Einsatzbereiche

¥ Sportstadien

¥ Kreuzfahrschiffe

¥ Mehrzweckhallen und -gebŠude

¥ KonzertsŠle

¥ gro§e Rufanlagen (Paging-Systeme)

¥ Schulen

¥ GerichtsgebŠude

¥ UniversitŠtsgebŠude

¥ Ausstellungen und VergnŸgungsparks

¥ BŸhnenhŠuser

¥ Fernunterricht

¥ HotelkonferenzrŠume

¥ Kirchen und religišse

BegegnungsstŠtten

¥ Tagungszentren

¥ Telekonferenzen

¥ verteilte Vielfachmikrofon-

Livesoundanlagen

¥ Stadthallen

¥ Musikclubs

¥ Theater

¥ Arenen

¥ alle Einrichtungen, die verteilte

Mikrofon- oder Line-Level-Signale benštigen

Dynamikbereich:

Mikrofon-Level:

-123 dBu Eingangsrauschersatz bei einem Eingangssignal mit 150 W und -

48 dBu ohne EingangsdŠmpfung, analoge EingangsverstŠrkung bei 60 dB, digitale VerstŠrkung bei 0 dB,

Analogausgang eingestellt auf maximal

+12 dBu (Jumper werkseingestellt auf

Durchgangs-VerstŠrkungsfaktor Eins)

Hinweis: Entspricht 78 dBA bzw. 75 dB ungewichtet.

Line-Level:

95 dBA bzw. 93 dB ungewichtet, gilt fŸr

+12 dBu-Eingangssignal, Eingangs-

/Ausgangs-VerstŠrkungsfaktor Eins.*

Eingangs-GleichtaktunterdrŸckung

(CAB 8i):

Besser als 65 dB bei beliebiger

VerstŠrkungseinstellung (Gain):

73 dB bei +12-dBu-Eingangssignal und

Eingangs-/Ausgangs-VerstŠrkungsfaktor

Eins*; 69 dB bei +4-dBu-Eingangssignal und Eingangs-/Ausgangs-

VerstŠrkungsfaktor Eins*; 68 dB bei -56dBu-Eingangssignal, ohne

EingangsdŠmpfung, analoge

EingangsverstŠrkung 60 dB, digitale

VerstŠrkung 0 dB, analoger Ausgang eingestellt auf maximal +12 dBu (Jumper werkseingestellt auf Durchgangs-

VerstŠrkungsfaktor Eins)

TECHNISCHE DATEN Ð AUDIO

AudiokanŠle:

CAB 8i: Acht EingangskanŠle fŸr Lineoder Mikrofon-Level mit schaltbarer 48-

V-Phantomspeisung

CAB 8o: Acht Line-Level-

AusgangskanŠle mit einzeln Ÿber

Jumper einstellbaren maximalen

Ausgangspegeln von +6, +12, +18 oder

+24 dBu (Werkseinstellung +12 dBu fŸr

13

Maximaler Eingangspegel (CAB 8i):

+29 dB bei 20-dB-EingangsdŠmpfung und analoger EingangsverstŠrkung von

0 dB; +38 dBu bei 20-dB-

EingangsdŠmpfung und analoger

EingangsverstŠrkung von -9 dB.

Hinweis: Analoge

EingangsverstŠrkungsregelung nicht gepuffert mit elektronisch symmetriertem

VerstŠrker, symmetrische

Eingangsschaltung mit Regelung in

1-dB-Schritten, spezifizierte

GleichtaktunterdrŸckung.

Maximaler Ausgangspegel

(CAB 8o):

+24 dBu an 600 W

VerstŠrkung (Gain) CAB 8i:

Softwaregeregelte analoge VerstŠrkung von -9 dB bis +60 dB, regelbar in 1-dB-

Schritten, Ÿber Software wŠhlbarer analoger Mic/Line-Eingangsschalter. (Bei

Wahl von Line-Level wird 20-dB-

EingangsdŠmpfungsglied zwischengeschaltet.)

VerstŠrkung (Gain) CAB 8o:

Softwaregeregelte analoge

AusgangsverstŠrkung von -95,5 dB bis

+31,5 dB, regelbar in 0,5-dB-Schritten, interne Analogausgangs-Jumper fŸr maximalen Ausgangspegel von +6, +12,

+18 oder +24 dBu.

Hinweis: Von der Verwendung als

Mikrofon-Level-Ausgang wird wegen des

Rauschens im extremen unteren

Ausgangspegelbereich abgeraten.

Eingangsimpedanz (CAB 8i):

Je nach Einstellung 22,2 kW fŸr Line-

Eingang und 2,2 kW fŸr

Mikrofoneingang.

Ausgangsimpedanz (CAB 8o):

100 W, minimale Nennbelastbarkeit

600 W

Analoge LED-Anzeige:

Acht Spitzenwertanzeigen (Anzeige der

Aussteuerungsreserve), kalibriert in dBu,

Ÿberwachen den Analogsignalpegel an den EingŠngen zu den A/D-Wandlern fŸr den CAB 8i sowie an den AusgŠngen der D/A-Wandler fŸr den CAB 8o.

Oberste rote LED zeigt ggf. eine A/Dbzw. D/A-†bersteuerung an.

Hinweis: Im Normalbetrieb sollte die oberste LED nie aufleuchten.

Hinweis 1: Die Audiome§werte beziehen sich je nach Zusammenhang auf den Eingang des CAB 8i und den

Ausgang des CAB 8o.

Hinweis 2: Alle Angaben sind typische

Daten.

*bedeutet keine EingangsdŠmpfung,

AnalogeingangsverstŠrkung 0 dB, digitale VerstŠrkung 0 dB,

Analogausgang eingestellt auf maximal

+12 dBu (Jumper werkseingestellt auf

Durchgangs-VerstŠrkungsfaktor Eins)

TECHNISCHE DATEN Ð DIGITAL

A/D- und D/A-Quantisierung:

24-Bit-Auflšsung

Audiosignal-†bertragungsquantisierung Ÿber CobraNet:

Ÿber Software schaltbar, 24- oder 20-Bit-

Auflšsung

Digitale Verarbeitung:

24-Bit-Signalprozessoren, 56-Bit-

Akkumulatoren

Nettogewicht:

CAB 8i: 3,86 kg

CAB 8o: 3,81 kg

Netzanschlu§:

Schaltnetzteil: maximal 1,4 A, 100 - 240 V~, 47 - 63 Hz

Leistung und WŠrmeabgabe:

CAB 8i: 25 W, 85 BTU/h

CAB 8o: 20 W, 68 BTU/h

Maximale Sto§stromstŠrke:

CAB 8i und CAB 8o: weniger als 1,4 A.

Audio-Abtast- und Taktrate:

Audio-Abtastrate 48 kHz, digitale

Signalprozessoren 80 MHz, Master-

Taktgeber12,288 MHz

AudiokanŠle CAB 8i/8o:

¥ acht bei Wahl der 20-Bit-†bertra gungsquantisierung

¥ sieben bei Wahl der 24-Bit-†bertra gungsquantisierung

Au§enflŠchen:

Stahl lackiert mit grauer

Pulverbeschichtung

Zubehšr:

abnehmbares Netzkabel, vier selbstklebende Gummif٤e

NormenerfŸllung:

UL, CUL, CE FCC Part 15, A

Technische Daten Ð Steuerung:

CobraNet-E/A:

100BaseT-Ethernet Ÿber achtpolige RJ-

45-Standardbuchse

RS-485:

Ein Port mit zwei dreipoligen Halbduplex-

MehrpunktanschlŸssen

TECHNISCHE DATEN F†R

SYSTEMINGENIEURE

Die Audiome§werte werden ggf. auf folgende Weise ermittelt: Eingangssignale werden CAB 8i zugefŸhrt und digital durch einen Ethernet-Hub Ÿbertragen;

Ausgangssignale werden vom CAB 8o abgegeben.

Steuerungsports:

Eingangssteuerspannung:

0 V= bis +10 V=, Regelung Ÿber externen Potentiometer oder externe

Spannungsquelle (Versorgungsspannung von 10 V= liegt intern an)

Softwaregesteuerter TTL- (Transistor-

Transistor-Logik-)Ausgang:

0 V= oder +5V=, Verteilung von maximal

28 mA auf 8 AusgŠnge

Acht softwaregesteuerte Relais mit sowohl Arbeits- als auch

Ruhekontakten:

Maximale Kontaktspannung:

120 V~ oder =

Maximaler Kontaktstrom:

2 A

Word-Clock-Ports:

zwei BNC-E/A-Ports

Hinweis: Verwendbar fŸr Umschaltung von einem CAB 8 auf ein zweites GerŠt

(Redundanz) im Stšrungsfalle.

TECHNISCHE DATENÐALLGEMEIN

Abmessungen:

CAB 8i und CAB 8o:

H: 44 mm, B: 483 mm, T: 297 mm

CAB 8i:

Das Peavey CAB 8i bietet acht KanŠle fŸr

Mikrofon- oder Line-Level-Audiosignale, die in ein Ethernet-Netzwerk eingespeist werden. Durch den Einsatz des CobraNet-

Audiosignal-†bertragungsprotokolls, das eine deterministische Signalverteilung ermšglicht, erfolgt die †bertragung der

Audiosignale Ÿber ein 100BaseT-(Fast-

)Ethernet Ÿber die volle Bandbreite mit hoher QualitŠt und ohne verlustreiche

Kompressionsverfahren, SignalausfŠlle oder sonstige QualitŠtsverluste.

Das GerŠt verfŸgt Ÿber 24-Bit-A/D-

Wandler mit einer auf 20 oder 24 Bit einstellbaren †bertragungs-Quantisierung unter Anwendung einer Abtastrate von

48 kHz.

Der Frequenzgang des GerŠts betrŠgt

20 Hz bis 20 kHz mit +0/-0,5 dB oder besser. Der Gesamtklirrfaktor betrŠgt bei einem +4-dBu-Eingangssignal hšchstens

0,01 % bei 1 kHz und 0,02 % bei 20 kHz.

Das GerŠt hat fŸr Line-Level-Signale einen Dynamikbereich von 95 dBA bzw.

93 dB ungewichtet und einen

Eingangsrauschersatzpegel von -124 dB fŸr Mikrofonsignale. Die

GleichtaktunterdrŸckung (CMRR) liegt bei

14

allen VerstŠrkungseinstellungen oberhalb von 65 dB. Der maximale Eingangspegel ohne †bersteuerung liegt bei +38 dBu unter Einhaltung der angegebenen

GleichtaktunterdrŸckung. Die

EingangsverstŠrkung des CAB 8i liegt zwischen -9 dB und +60 dB und ist in 1dB-Teilschritten regelbar. Die

Eingangsimpedanz des CAB 8i betrŠgt 2,2 kW fŸr Mikrofonsignale (20-dB-

AusgangsdŠmpfung) und 22,2 kW fŸr

Line-Signale (20-dB-EingangsdŠmpfung).

Die Steuerfunktionen umfassen acht

Relais mit sowohl Ruhe- als auch

Arbeitskontakten sowie acht TTL-

SteuerausgangskanŠle. Beide sind Ÿber ein Ethernet-Link durch Software ansteuerbar. Ferner sind acht analoge

Steuerspannungs-EingangskanŠle mit

Ports zum Ansteuern von Parametern der

MediaMatrix-Software durch externe

Schalter, Potentiometer oder

Spannungsquellen Ÿber ein Ethernet-Link vorgesehen.

Die Anzeigeinstrumente an der

Frontblende zeigen folgende

SystemzustŠnde an: SignalŸbertragung,

Signalempfang, †bertragungsfehler,

Empfangsfehler, Stšrungsanzeige, Link-

Anzeige, Leiterzustand, Zustand der

Steuerung Ÿber RS-485 sowie das

Anliegen der Betriebsspannung. Ferner sind auf der Frontblende acht

Spitzenwertanzeigen (Anzeige der

Aussteuerungsreserve) angebracht, die die Analogsignalpegel an den EingŠngen zu den A/D-Wandlern Ÿberwachen. Die oberste rote LED zeigt ggf. eine A/D- bzw.

D/A-†bersteuerung an.

Das GerŠt ist ohne StandfŸ§e 483 mm breit, 327 mm tief und 44 mm hoch. Es wiegt netto 3,86 kg und entspricht einer

Rack-Hšheneinheit (44 mm). Sein lŸftergekŸhltes StahlgehŠuse ist mit graufarbener Pulverbeschichtung versehen.

Das GerŠt verbraucht maximal 25 W und nimmt maximal 1,4 A Strom auf. Im

Lieferumfang inbegriffen sind ein abnehmbares Netzkabel und vier

GummifŸ§e. Das GerŠt erfŸllt die normativen Vorschriften von UL, CUL und

CE sowie Teil 15 A der FCC-Vorschriften.

Die Typenbezeichnung lautet Peavey

Electronics Corporation Modell CAB 8i.

CAB 8o:

Das CABª 8o bietet acht KanŠle fŸr Line-

Level-Audiosignale, die aus einem

Ethernet-Netzwerk aufgenommen werden.

Durch den Einsatz des CobraNet-

Audiosignal-†bertragungsprotokolls, das eine deterministische SignalŸbermittlung

Ÿber Ethernet ermšglicht, erfolgt die

†bertragung der Audiosignale Ÿber ein

100BaseT-(Fast-)Ethernet Ÿber die volle

Bandbreite mit hoher QualitŠt und ohne verlustreiche Kompressionsverfahren,

SignalausfŠlle oder sonstige

QualitŠtsverluste. Das GerŠt verfŸgt Ÿber

24-Bit-A/D-Wandler mit einer auf 20 oder

24 Bit einstellbaren †bertragungs-

Quantisierung unter Anwendung einer

Abtastrate von 48 kHz.

An der RŸckwand des GerŠts befinden sich ein abnehmbares Netzkabel, ein

Hauptschalter zum Einschalten der

Stromversorgung sowie eine Netzstrom-

Steckdose mit eingebautem selbstrŸcksetzendem Unterbrecher. Externe oder interne Sicherungen sind nicht zulŠssig. Ferner sind zwei Word-Clock-

AnschlŸsse vorgesehen, die im

Stšrungsfall eine automatische

Umschaltung auf ein RedundanzgerŠt ermšglichen. Zur Erleichterung der

Anschlu§installation und der

Stšrungssuche sind abnehmbare Euro-

Schraubklemmen fŸr abisolierte Kabel vorhanden. An diesen Klemmen werden alle Line- und Mikrofon-LevelanschlŸsse sowie alle Steuerspannungs-, TTL-,

Relais- und RS-485-AnschlŸsse vorgenommen. FŸr die Einbindung in das

Ethernet-Netzwerk verfŸgt das GerŠt Ÿber eine achtpolige RJ-45-E/A-

Standardbuchse.

Der Frequenzgang des GerŠts betrŠgt 20

Hz bis 20 kHz mit +0/-0,5 dB oder besser.

Der Gesamtklirrfaktor betrŠgt bei einem

+4-dBu-Ausgangssignal hšchstens 0,01 % bei 1 kHz und 0,02 % bei 20 kHz. Der

Dynamikbereich umfa§t 95 dBA bzw. 93 dB ungewichtet. Der maximale

Ausgangspegel betrŠgt +24 dBu bei einer

Last von 600 W oder mehr. Die

VerstŠrkung des CAB 8o liegt zwischen -

95,5 dB und +31,5 dB und ist in 0,5-dB-

Teilschritten regelbar. Die

Ausgangsimpedanz des CAB 8o betrŠgt

100 W und ist fŸr eine Last von 600 W oder mehr ausgelegt.

Die Steuerfunktionen umfassen acht

Relais mit sowohl Ruhe- als auch

Arbeitskontakten sowie acht TTL-

SteuerausgangskanŠle. Beide sind Ÿber ein Ethernet-Link durch Software ansteuerbar. Ferner sind acht analoge

Steuerspannungs-EingangskanŠle vorgesehen, Ÿber deren Ports Parameter der MediaMatrix-Software durch externe

Schalter, Potentiometer oder

Spannungsquellen mittels eines Ethernet-

Links angesteuert werden kšnnen.

Die Anzeigeinstrumente an der

Frontblende zeigen folgende

SystemzustŠnde an: SignalŸbertragung,

Signalempfang, †bertragungsfehler,

Empfangsfehler, Stšrungsanzeige, Link-

Anzeige, Leiterzustand, Zustand der

Steuerung Ÿber RS-485 sowie anliegende

Betriebsspannung. Ferner sind auf der

Frontblende acht Spitzenwertanzeigen

(Anzeige der Aussteuerungsreserve) angebracht, die die Analogsignalpegel an den AusgŠngen der D/A-Wandler

Ÿberwachen. Die oberste rote LED zeigt ggf. eine D/A-†bersteuerung an.

An der RŸckwand des GerŠts befinden sich ein abnehmbares Netzkabel, ein

Hauptschalter zum Einschalten der

Stromversorgung sowie eine Netzstrom-

Steckdose mit eingebautem selbstrŸcksetzendem Unterbrecher. Externe oder interne Sicherungen sind nicht zulŠssig. Ferner sind zwei Word-Clock-

AnschlŸsse vorgesehen, die im

Stšrungsfall eine automatische

Umschaltung auf ein RedundanzgerŠt ermšglichen. Zur Erleichterung der

Anschlu§installation und der

Stšrungssuche sind abnehmbare Euro-

Schraubklemmen fŸr abisolierte Leiter vorhanden. An diesen Klemmen werden alle Line-Level-, Steuerspannungs-, TTL-,

Relais- und RS-485-AnschlŸsse vorgenommen. FŸr die Einbindung in das

Ethernet-Netzwerk verfŸgt das GerŠt Ÿber eine achtpolige RJ-45-E/A-

Standardbuchse.

Das GerŠt ist ohne StandfŸ§e 483 mm breit, 327 mm tief und 44 mm hoch. Es wiegt netto 3,81 kg und entspricht einer

Rack-Hšheneinheit (44 mm). Sein lŸftergekŸhltes StahlgehŠuse ist mit graufarbener Pulverbeschichtung versehen.

Das GerŠt verbraucht maximal 20 W und nimmt maximal 1,4 A Strom auf. Im

Lieferumfang inbegriffen sind ein abnehmbares Netzkabel und vier

GummifŸ§e. Das GerŠt erfŸllt die normativen Vorschriften von UL, CUL und

CE sowie Teil 15 A der FCC-Vorschriften.

Die Typenbezeichnung lautet Peavey

Electronics Corporation Modell CAB 8o.

15

©1999

3 + 2 YEAR LIMITED WARRANTY

NOTE: For details, refer to the warranty statement. Copies of this statement may be obtained by contacting

Peavey Electronics Corporation

P.O. Box 2898, Meridian, Mississippi 39301-2898.

ARCHITECTURAL ACOUSTICS ¨

Features and specifications subject to change without notice.

Peavey Electronics Corporation • 711 A Street • Meridian • MS • 39301

(601) 483-5376 • FAX (601) 486-1678 • aa.peavey.com

80304547

Printed in the U.S.A. 5/99

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement