17” CDT Color Monitor
107B7
Service
Service
Service
Horizontal Frequency
30-86 kHz
TABLE OF CONTENTS
Description
Page
Description
Page
Table Of Contents...................................................1
7-1.Noraster,CRT relative circuit problems...........……........28
Revision List.......................................................2
7-2. Abnormal displays................………………………..…...30
I mp o r t a n t S a f et y N o t ic e . .. .. .. . .. .. .. . .. .. ... .. . . ... .. .. 3
7-3 No blanking................................................31
1. Specifications..........................................4
7-4 Hor./OSC/DEF/HV circuit fault................................31
2. Precaution and notices................................7
7-5. Abnormal horizontal deflection...................................32
2-1Safety precautions....…...............…..............7
7-6. Abnormal vertical scanning............…........................33
2-2 Product safety notice ..........................................7
7-7. Side-pin cushion distortion.........………………........33
2-3 Service Notices....................…………......7
7-8. Poor focus...................................…….............33
2-4 High voltage warning............................................8
7-9. Power supply trouble shooting chart.................35
3. Operating Instructions................…………….............9
8. Mechanical of cabinet front dis-assembly...………......35
4. Adjustment .........................……………………….......10
9. Spare parts list........ .................. ............. ...36
4 -1. Adjustment conditions and precautions ...……........10
10. Different parts list..........................................47
4-2. Main adjustments.........…………………...................10
11 Block diagram............................................48
4-3 Adjustment methods........................................13
12 IC block diagrams.............................................49
4-4 DDC Instructions………………………….……….…….17
13 PCB layout............................................55
5.Circuit description ..……..……………………............22
13-1 Main PCB layout..........................................55
5-1.Micro controller and deflection circuit .………….......22
13-2. CRPC board layout.........................................56
5-2.Transistor & diode circuit...............................24
14. Schematic diagram.........................................57
6.Mechanical Instructions......................…………….......25
15. General Product Specification…………………………61
7.Trouble shooting chart..........................……….......28
SAFETY NOTICE
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS AND BE AWARE OF THE
NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
GB 3138 106 10530
1
17” CDT Color Monitor
107B7
Revision List
Version
Date
A00
May-28-2006
Revision History
Initial Release
2
17” CDT Color Monitor
107B7
Important Safety Notice
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS
AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC
EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFORMER FOR THIS UNIT WHEN SERVICING
REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINGS
Proper service and repair is important to the safe, reliable operation of all PHILIPS Company Equipment. The service
procedures recommended by PHILIPS and described in this service manual are effective methods of performing
service operations. Some of these service operations require the use of tools specially designed for the purpose. The
special tools should be used when and as recommended.
It is important to note that this manual contains various CAUTIONS and NOTICES which should be carefully read in
order to minimize the risk of personal injury to service personnel. The possibility exists that improper service methods
may damage the equipment. It is also important to understand that these CAUTIONS and NOTICES ARE NOT
EXHAUSTIVE. PHILIPS could not possibly know, evaluate and advise the service trade of all conceivable ways in
which service might be done or of the possible hazardous consequences of each way. Consequently, PHILIPS has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not
recommended by PHILIPS must first satisfy himself thoroughly that neither his safety nor the safe operation of the
equipment will be jeopardized by the service method selected.
Hereafter throughout this manual, PHILIPS Company will be referred to as PHILIPS.
WARNING
Use of substitute replacement parts, which do not have the same, specified safety characteristics may create shock,
fire, or other hazards.
Under no circumstances should the original design be modified or altered without written permission from PHILIPS.
PHILIPS assumes no liability, express or implied, arising out of any unauthorized modification of design. Servicer
assumes all liability.
FOR PRODUCTS CONTAINING LASER:
DANGER - Invisible laser radiation when open. AVOID DIRECT EXPOSURE TO BEAM.
AUTION - Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
CAUTION - The use of optical instruments with this product will increase eye hazard.
TO ENSURE THE CONTINUED RELIABILITY OF THIS PRODUCT, USE ONLY
ORIGINAL MANUFACTURER'S REPLACEMENT PARTS, WHICH ARE LISTED WITH
THEIR PART NUMBERS IN THE PARTS LIST SECTION OF THIS SERVICE MANUAL.
3
17” CDT Color Monitor
107B7
1. Monitor Specifications
1.
CRT : 43.2CM(17") 90 Deflection, 29mm Neck, 0.25mm phosphor dot pitch, Pure Flat high brightness high
contrast CRT, Non-Glare Screen
2.
Viewable image Size: 40.6CM (16") diagonal
3.
Display Color: Unlimited Colors
4.
External Controls:
Power On/Off, OSD key, OSD Function: Contrast, Brightness, H-Center, H-Size, V-Center, V-Size, Zoom,
Pincushion, Trapezoid, Pin-Balance, Parallelogram, Rotation, 6500 Color Temperature, 6500 Color
Temperature, User Color, 9300 Color Temperature, Degauss, Moire Reduce, Recall, Exit, Language.
5.
Input Video Signal
6.
7.
Timing
Resolution
H. Frequency
V. Frequency
1.
640 x 480
31.469 kHz
59.941 Hz
2.
640 x 480
43.269 kHz
85.008 Hz
3.
720 x 400
31.468 kHz
70.084 Hz
Timing
Resolution
H. Frequency
V. Frequency
4.
800 x 600
46.875 kHz
75.000 Hz
5.
800 x 600
53.674 kHz
85.061 Hz
6.
1024 x 768
60.023 kHz
75.029 Hz
Timing
Resolution
H. Frequency
V. Frequency
7.
1024 x 768
68.677 kHz
84.997 Hz
8.
1280 x 1024
79.976 kHz
75.024 Hz
Scanning Frequencies
Horizontal:
Vertical:
30KHz ~ 86KHz
50 Hz ~ 160 Hz
Factory Preset Timings: 8
User Timings:6
8. Main dimensions/weight
Monitor (with stand)
Width:
Height:
Depth:
Weight:
397 mm
428 mm
423.5 mm
13.5 kg
Packed Monitor (for
China, India)
460 mm
450 mm
526 mm
15.8 kg
9.POWER CONSUMPTION
Power on -
< 75w.
DPMS off state -
< 2w at 240Vac.
Power off (by switch) -
< 1w at 120Vac, <2w at 240Vac.
4
Packed Monitor(for
other regions)
446 mm
420 mm
475 mm
15.4 kg
17” CDT Color Monitor
107B7
10. Video Bandwidth: 180 MHz
11. Power Source:
Switching Mode Power Supply
AC 90 ~264V, 50±3/60±3Hz Universal Type
12. Operating Temperature: 0°C to 40°C Ambient
13. Humidity: 5% to 90% Relative, Non-Condensing
14. External Connection:
15 Pin D-type Connector
AC Power Cord
15. Regulations/Safety:
International Regulatory Specification
SAFETY / EMC / ERGONOMICS /
STANDARDS
COUNTRY
DOMAIN
INTERNATIONAL
Sa
IEC60950-1: 2001. Group -and national
differences of all countries listed in CB
Bulletin No. 107A
Sa
European Low Voltage Directives
73/23/EEC and 93/68/EEC
CB Report and CB certificate
Declaration of Conformity
European Electromagnetic Compatibility
Directive 89/336/EEC amended by the
directive 93/68/EEC. EN 55022:1998
Class B
EUROPE
E
Sa
GERMANY
DOCUMENTS
O
EN 55024: 1998
Declaration of Conformity and Full
EMC/CE test report
EN 61000-3-2: 2000
IEC 61000-3-3: 1994/EN61000-3-3:
1995
CISPR 22:1997 Class B International
EMC standard
EN60950-1: 2001
ISO 9241-3-7-8 (CRT) & 13406-2 (LCD),
prEN 50279:1998
O
GS-Mark / EK1-ITB 2000
X
Decree
Sa
EN60950-1: 2001
TUV certificate
TUV-ERG certificate
TUV-GS certificate
ROV 08.01.87 (CRT)
PTB
SEMKO certificate
O
TCO 99 (TCO03) (to TCO models)
O
MPR 1990: 8 / MPR 1990:10 (to MPR
models)
Meet requirement
RUSSIA
Sa
GOST R 50377-1992
GOST certificate
SOUTH AFRICA
Sa
SABS IEC 60950 and IEC 60950-1
SWEDEN
5
TCO99 (TCO03) report + certificate
Certificate of Conformity
17” CDT Color Monitor
USA
CANADA
MEXICO
KOREA
SINGAPORE
CHINA
TAIWAN
AUSTRALIA/
NEW-ZEALAND
ISRAEL
Saudi Arabia
Japan
Argentina
107B7
E
EN55022 or Cisper 22
Certificate of Conformity
Sa
UL 60950-1: 2003
UL certificate
E
FCC Part 15 Class B
FCC ID grant or DOC
O
Energy Star
X
21CFR 1002.10 to 13 (CRT)
Sa
CSA C22.2 No 60950
E
ICES-003 issue 3
E
RED (CRT)
Sa
NOM-019-SCFI-1994
Sa
Korean Safety Control law IEC 60950
E
Regulations laws: EMI 1996-78, 80. EMS
1996-79,81
MIC certificate
Sa
IEC60950
PSB certificate
Sa
GB4943-2001
E
GB9254-1998; 17625.1-2003
O
CSC/G1205-2004
Sa
CNS-14336
E
CNS-13438 (CISPR22) Class B
O
Criteria 18 (Monitor) (LCD)
E
AS/NZS3548: 1995
Declaration of Conformity
S
IS 1121, IEC60950/IEC60950-1
Certificate of Conformity
E
EN or Cisper 22
Certificate of Conformity
S
IEC standard
SASO
E
IEC standard
SASO
EPA registration
DHHS report
CSA certificate
Statement on label
DNHW
NOM certificate
eK certificate
CCC certificate
CECP certificate
(IEC 60950-1)
Sa
EN60950-1:001 (AC adapter only)
E
VCCI class B (CISPR 22)
Sa
EN60950-1: 2001
BSMI certificate
Green Mark / certificate
PSE
VCCI Certificate
IRAM
Sa = Safety
E = Electromagnetic Compatibility
O = Other which including recycling, energy saving, ergonomics
X = X-ray
For detailed regulatory items please refer to the international regulatory specification provided by Philips.
6
17” CDT Color Monitor
107B7
2. Precautions and notices
2-1.Safety precautions
1.
Observe all caution and safety related notes located inside the display cabinet.
2.
Operation of the display with the cover removed, may cause a serious shock hazard from the display power
supply. Work on the display should not be attempted by anyone who is not thoroughly familiar with
precautions necessary when working on high voltage equipment.
3.
Do not install, remove or handle the picture tube in any manner unless shatter-proof goggles are worn.
People who are not so equipped should be kept away while handling picture tube. Keep picture tube away
from the body while handling.
4. The picture tube is constructed to limit X-RAY radiation to 0.5 mR/HR. For continued protection, use the
designated replacement tube only, and adjust the voltages so that the designated maximum rating at the
anode will not be exceeded.
5. Symbol“
“ means safety relative parts. The use of substitute replacement parts which do not have the
same characteristics as specified in the parts list may create shock, fire or explode etc.
6. Symbol“ ” means X-ray relative parts. Before replacing any of these components please read the parts
list in this manual carefully to avoid creating higher anode voltage or x-ray. Especially for sealed controls,
such as VR902 and FBT screen VR etc, which were sealed by the manufacturer once their optimum
position has been set, please don’t dismantle them as your likes, otherwise you will break or damage the
component. If you need replace the parts with sealed control, please adjust the relative VR to make sure the
B+ voltage about 53.5.0V and well seal it with A+B glue or equivalent, which you can not move away with
one screw driver
7.
Before returning a serviced display to the customer, a thorough safety test must be performed to verify that
the display is safe to operate without danger or shock. Always perform an AC leakage current check on the
exposed metallic parts of the cabinet, such as screw heads.
Test method for current leakage is described as follow.
(a) Plug the AC line cord directly into rated AC outlet (do not use a line isolation transformer during this
check).
(b) Use an AC voltmeter having 5000 ohms per volt or with more sensitivity in the following manner:
Connect a 1500 ohms 10 Watt resistor, paralleled by a 0.15UF, AC type capacitor between a known
good earth ground (water pipe, conduit, etc.) and the exposed metallic parts simultaneously. Measure
the AC voltage across the combination of 1500 ohms resistor and 0.15UF capacitor.
(c) Reverse the AC plug at the AC outlet and repeat AC voltage measurements for each exposed metallic
part.
(d) Voltage measured must not exceed 0.5 volts RMS. This corresponds to 0.35 milliamp AC. Any value
exceeding this limit constitutes a potential shock hazard and must be corrected immediately.
7
17” CDT Color Monitor
107B7
2-2 Product safety notice
Many electrical and mechanical parts in this chassis have special safety visual inspections and the protection
afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage,
wattage, etc. Before replacing any of these components read the parts list in this manual carefully. The use of
substitute replacement parts which do not have the same safety characteristics as specified in the parts list may
create shock, fire, X-RAY radiation or other hazards.
2-3 Service notes
1.
When replacing parts or circuit boards, clamp the lead wires around terminals before soldering.
2.
When replacing a high wattage resistor (more than 1/2W of metal oxide film resistor) in circuit board, keep
the resistor about 10mm (1/2 in) away from circuit board.
3.
Keep wires away from high voltage or high temperature components.
4.
Keep wires in their original position so as to reduce interference.
2-4 High voltage warning
Operation of monitor outside of cabinet or with back removed may cause a serious shock hazard. Work on this
model should only be performed by those who are thoroughly familiar with precautions necessary when working
on high voltage equipment.
Exercise care when servicing this chassis with power applied. Many B plus and high voltage terminals are
exposed which, if carelessly contacted, can cause serious shock or result in damage to the chassis. Maintain
interconnecting ground lead connections between chassis and picture tube dag when operating chassis.
Certain HV failures can increase X-ray radiation. Monitor should not be operated with HV levels exceeding the
specified rating for the chassis type. The maximum operating HV specified for the chassis used in this monitor is
23.0KV ± 1KV
with a line voltage of 120/240 VAC. Higher voltage may also increase possibility of failure in HV supply.
It is important to maintain specified values of all components in the horizontal and high voltage circuits and
anywhere else in the monitor that could cause a rise in high voltage or operating supply voltages. No changes
should be made to the original design of the monitor. Components shown in the shaded areas on the schematic
should be replaced with exact factory replacement parts. The use of unauthorized substitute parts may create a
shock, fire or other hazard.
To determine the presence of high voltage, use accurate, high impedance, HV meter connected between second
anode lead and CRT dag grounding device. When servicing the High Voltage System, remove static charge from
it by connecting a 10K ohm resistor in series with an insulated wire (such as a test probe) between picture tube
dag and 2nd anode lead.(AC line cord disconnected from AC power outlet.)
The picture tube used in this monitor employs integral implosion protection. Replace with tube of the same type
number for continue safety. Do not lift picture tube by the neck. Handle the picture tube only after discharging the
high voltage completely.
8
17” CDT Color Monitor
107B7
3. Operating instructions
This procedure gives you instructions for installing and using the Color display.
1.
Position the display on the desired operation and plug the power cord into a convenient AC outlet. Threewire power cord must be shielded and is provided as a safety precaution as it connects the chassis and
cabinet to the electrical conduit ground. If the AC outlet in your location does not have provisions for the
grounded type plug, the installer should attach the proper adapter to ensure a safe ground potential.
2. Connect the 15-pin color display shielded signal cable to your signal system device and lock both screws on
the connector to ensure firm grounding. The connector information is as follow:
1
5
6
10
11
15
15 - Pin Color Display Signal Cable
Pin No.
1.
2.
3.
4.
5.
6.
7.
8.
3.
Description
Red video
Green video
Blue video
GND
Self test
Red GND
Green GND
Blue GND
Pin No.
9.
10.
11.
12.
13.
14.
15.
Description
+5V (Supply from PC for DDC circuit)
Sync GND
GND
DDC serial data
H-sync
V-sync
DDC serial clock
Apply power to the display by turning the power switch to the "ON" position and allow about thirty seconds
for display tube warm-up. The Power-On indicator lights when the display is on.
4.
With proper signals feed to the display, a pattern or data should appear on the screen, adjust the brightness
and contrast to the most pleasing display.
5.
This monitor has power saving function following the VESA DPMS. Be sure to connect the signal cable to
the PC.
6.
If your color display requires service, it must be returned with the power cord.
9
17” CDT Color Monitor
107B7
4. Adjustment
4-1 Adjustment conditions and precautions
1.
Approximately 30 minutes should be allowed for warm up before proceeding.
2.
Adjustments should be undertaken only on those necessary elements since most of them have been carefully
preset at the factory.
4-2 Main adjustments
10
17” CDT Color Monitor
107B7
Basic and simple instruction on the control keys
On the front controls of your monitor, once you press the MENU button, the On Screen Display
(OSD) Main Controls window will pop up and you can now start making adjustments to your
monitor's various features. Use the
to make your adjustments within.
The OSD Tree
Below is an overall view of the structure of the On-Screen Display. You can use this as reference
when you want to later on work your way around the different adjustments.
Your monitor may not include all the items in the OSD tree shown below.
11
17” CDT Color Monitor
107B7
12
17” CDT Color Monitor
107B7
4-3 Adjustment method
1. B + & HV voltage adjustment:
A.Chroma-2135 Signal generator or PC equivalent set mode 6, UVGA 1280X1024 pattern 101 .
B.Connect a DC Volt meter between TP902 and ground, then adjust VR902 to be 140±1 VDC for CPT and LG
CRT.
C.Set the contrast and brightness max,and then adjust G2=600V for CPT CRT and G2=560V for LG CRT.
2. Factory preset Timings Adjustment:
A. Press MENU Key to show OSD menu ,and press the down Key to select the "ZOOM" function,
B. Then press the menu Key to enter second menu, press the down key to select zoom”
” about 10S.
Do not release it, until the OSD menu changed to the Factory preset window.
C. The Factory preset window contains the following functional controls. Select one of the control. Then press
the Left/Right ,Up/Down Key to adjust its value for the optimum picture.
SR
Save SRGB color
VO
V Offset
55
Save 5500C color
VG
V Gain
OS
User OSD size
HM
H size Max
LH
Brightness
HR
H Size Range
SB
SBQ
HS
HSUB Size Range
BI
Set Burn/in Off & On
HG
H Gain
SW
Set H/Freq Max 85~72K
HBRIOSD VC
DC
DCOffset ADJ
HBRIOSD HC
AB
ABL
User adjustment
13
17” CDT Color Monitor
107B7
OV
User OSD VC
Save and Exit
OH
User OSD HC
Degauss
EA
EHT Auto Adjustment
B-Bias
HE
HEHT Gain
G-Bias
VE
VEHT Gain
R-Bias
EO
EHT Offset
G-Gain
EU
EHT Current
B-Gain
BP
B Plus
R-Gain
BB
Bottom Balance
Brightness
TB
Top Balance
Contrast
HB
HS Wave Balance
V-Moire Reduce
HS
HSWAVE
H-Moire Reduce
TM
User Timr:00273hours
PIN-Balance
65
Save 6500C color
Parallelogram
93
Save 9300C color
Trapezoid
VF
V-Focus
Pincushion
VB
VLIN Balance
Rotation
VI
V Linearity
V- Center
HL
H Linearity
V-size
BC
Bottom Corner
H-Center
TC
TOP Corner
H -size
D. To switches the input signal to the other Timing Mode. Please follow step A ~ C to get the optimum
picture.(H/V-size:312*234mm)
E. Select the "
" RETURN function and press the MENU Key, then the Factor Preset window will be
returned to the original OSD window.(user's operating condition)
F. The setting data of the CONTRAST, BRIGHTNESS, ROTATION, COLOR TEMPERATURE are common
mode saved in the memory. Don't needed adjust it individual at every timing Mode and save in the memory.
3. White Balance, Luminance adjustment:
14
17” CDT Color Monitor
107B7
A. Press MENU Key to show OSD menu ,and press the down Key to select the "zoom" function, then press
the menu Key to enter second menu, press the down key to select “
“above 10S,then enter into factory
setting area for modulation.
B. Brightness & contrast ratio MAX.
C. Raster Max modulation: Raster Pattern, adjust R or B bias and G2, make x=270±10, y=290±10, Y=2.0±0.2
cd/m2
D. Raster cut off modulation: Raster Pattern, adjust brightness to make Cut off: 0.08±0.02 cd/m2,and then put
9300K & 6500K into it.
E.Small white screen appears, Raster cut off, set SB as 4
(1)Choose 4 for LH ,set R or G or B gain, make x=283±15, y=297±15,Y=350±15 cd/m2,then save it into
9300K color temperature, set R or G or B gain, make x=313±15, y=329±15, Y=300±15,then save it into 6500K
color temperature, set R or G or B gain, make x=332±15, y=347±15, Y=280±15,then save it into 5500K color
temperature, then exit the factory setting area.
(2)Choose 3 for LH,set R or G or B gain, make x=283±15, y=297±15,Y=270±15,then save it into 9300K color
temperature; set R or G or B gain, make x=313±15, y=329±15,Y=250±15,then save it into 6500K color
temperature, set R or G or B gain, make x=332±15, y=347±15, Y=230±15,then save it into 5500K color
temperature, then exit the factory setting area.
(3)Choose 2 for LH,set R or G or B gain, make x=283±15, y=297±15,Y=210±15,then save it into 9300K color
temperature; set R or G or B gain, make x=313±15, y=329±15,Y=200±15,then save it into 6500K color
temperature, set R or G or B gain, make x=332±15, y=347±15, Y=190±15,then save it into 5500K color
temperature, then exit the factory setting area.
(4)Choose 1 for LH,set R or G or B gain, make x=283±15, y=297±15,Y=140±15,then save it into 9300K color
temperature; set R or G or B gain, make x=313±15, y=329±15,Y=130±15,then save it into 6500K color
temperature, set R or G or B gain, make x=332±15, y=347±15, Y=120±15,then save it into 5500K color
temperature, then exit the factory setting area.
F. White screen appears, brightness cut off, set “SB” as 4,adjust AB value, make 9300K color temperature
Y=98±1 cd/m2,then save it into 9300K color temperature; set “SB” as 3,adjust AB value, make 9300K color
temperature Y=96±1 cd/m2,then save it into 9300K color temperature; set “SB” as 2, adjust AB value, make
2
9300K color temperature Y=94±1 cd/m ,then save it into 9300K color temperature; set “SB” as 1, adjust AB
value, make 9300K color temperature Y=92±1 cd/m2,then save it into 9300K color temperature.
G. White screen appears, brightness cut off, set R or G or B gain, make x=313±10, y=329±10,Y=80±5 cd/m2 .
then save it into sRGB color temperature, exit the factory setting area.
H. After modulation, it’s necessary to check if the white balance accords with the normal specification. If not,
needs reset. then exit factory setting area.
4. Focus Adjustment:
A. Set mode7 1024×768@85Hz with character full page.
B. Under the RECALL state.
15
17” CDT Color Monitor
107B7
C. Then adjust focus VR1 to a fine vertical line.
D. Adjust focus VR2 to a fine horizontal line.
E. Repeat step C & D,after that ,set the Focus VR,G2 VR with the white lacquer.
5. Purity Adjustment
A. Be sure that the display is not being exposed to any external magnetic fields.
B. Ensure that the spacing between the Purity, Convergence, Magnet, (PCM), assembly and the CRT stem is
29mm. (See below diagram)
C. Produce a complete, red pattern on the display. Adjust the purity magnet rings on the PCM assembly to
obtain a complete field of the color red. This is done by moving the two tabs in such a manner that they
advance in an opposite direction but at the same time to obtain the same angle between the two tabs,
which should be approximately 180'.
D. Check the complete blue and complete green patterns to observe their respective color purity. Make minor
adjustments if needed.
Relative placement of typical components
Purity Magnets
6-pole Convergence Magnets
4-pole Convergence Magnets
Deflection Yoke
6. Convergence adjustment
A. Produce a magenta crosshatch on the display.
B. Adjust the focus for the best overall focus on the display.
Also adjust the brightness to the desired condition.
C. Vertical red and blue lines are converged by varying the angle between the two tabs of the 4 pole magnets
on the PCM assembly. (See above diagrams)
D. Horizontal red and blue lines are converged by varying the two tabs together, keeping the angle between
them constant.
E. Produce a white crosshatch pattern on the display.
F. Vertical green and magenta lines are converged by varying the angle between the two tabs of the 6-pole
magnets.
G. Horizontal green and magenta lines are converged by varying the two tabs together, keeping the angle
between them constant.
16
17” CDT Color Monitor
107B7
4-4 DDC Instructions
128 bytes EDID Data (Hex):
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
0
00
FF
FF
FF
FF
FF
FF
00
41
0C
1D
00
01
00
00
00
16
01
0F
01
03
68
20
18
78
2B
9E
A8
A1
54
46
99
24
32
0E
48
4C
A5
EF
00
31
59
45
59
61
59
71
4F
81
80
48
81
59
A9
40
A9
45
EA
24
00
60
41
00
28
30
30
60
64
13
00
36
E6
10
00
00
1E
00
00
00
FF
00
41
55
30
80
35
30
31
30
30
30
30
30
31
0A
00
00
00
FD
00
32
96
A0
1E
56
12
00
0A
20
20
20
20
20
20
00
00
00
FC
112
00
50
48
31
30
37
42
37
0A
20
20
20
20
20
00
2E
Take 105G7 DDC writer for example
1.General
DDC Data Re-programming
In case the main EEPROM with Software DDC which store all factory settings were replaced because a defect,
repaired monitor’ the serial numbers have to be re-programmed.
It is advised to re- soldered the main EEPROM with Software DDC from the old board onto the new board if circuit
board have been replaced, in this case the DDC data does not need to be re-programmed.
Additional information:
Additional information about DDC (Display Data Channel) may be obtained from Video Electronics Standards
Association (VESA). Extended Display Identification Data (EDID) information may be also obtained from VESA.
2.System and equipment requirements
1. An i486 (or above) personal computer or compatible.
2. Microsoft operation system Windows 95/98,etc.
3. Newphl.exe program
4. (105G7)S554BPHL.ddc EDID program.
5. Software DDC Alignment kits shown as fig 1.
The kit contents:
a. DDC board x1
b. Printer cablex1
c. D-Sub cable x1
d. 12V DC input
Note: The Newphl.exe is a MS-DOS -based program, which cannot be run in windows.
17
17” CDT Color Monitor
107B7
D-SUB connector
Printer connector
DC 12V input
Fig 1
Step 1: Put the “Newphl.exe” and “(105G7) S554BPHL.ddc” to a special folder, such as 105G7. And rename the
“(105G7) S554BPHL.ddc” as “W.ddc”
Step 2: Access to MS-DOS program, Input the command as shown fig 2
Fig 2
Note: g: is the disk position for 105G7
18
17” CDT Color Monitor
107B7
Step 3: Press Enter into the next screen as shown Fig 3.
a. Input 14 byte digital Serial No. such as “11111111111111” as shown Fig 3.
b. Enter and press “F3” key to input Serial No. again as shown Fig 4. Enter
The Serial No. length is”14” as shown Fig 4.
c. If you correctly input, there will appear” The Barcode length: 14 is OK” as shown Fig 5.
d. And if you incorrectly input, there will appear “The Barcode length: 9 is NG” as shown Fig 6.
You have to input again.
Fig 3
Fig 4
19
17” CDT Color Monitor
107B7
Fig 5
Fig 6
Step 4: Enter, go into the next screen as shown Fig 7.
Fig 7
20
17” CDT Color Monitor
107B7
Step 5: Enter into Fig 8.
Fig 8
Step 6: Enter into Fig 9.
Fig 9
21
17” CDT Color Monitor
107B7
5. Circuit description
5-1 Micro controller and deflection circuit
Micro Controller
The micro controller(IC101) core is a 80C51 type. The micro clock frequency of 12 Mhz is derived from the
Xtal oscillator, which is running at 48MHz. The DDC interface is suitable to handle DDC2 by a modified hardware
I2C-bus interface .Standard high current ports,3 ADC pouts with voltage inputs and 4 static standard 8 bit DAC
outputs (low interference) and one PWM output for digital control application are implemented. The central
processing unit (CPU) manipulates operands in two memory spaces. These are the 1024byte internal data
memory(consisting of 256 bytes standard RAM and 768 bytes AUX-RAM) and 48K-byte internal program memory .
The program memory of the SAA4849 consists of 48K bytes ROM.
The SAA4849P provides sync. Processing with full auto sync. Capability, a flexible SMPS block and an
extensive set of geometry control facilities. Further the IC generates the drive waveforms for DC coupled vertical
boosters to the TDA4863A.
H/V sync signals processor
The functions of the sync processor include polarity detection, H-SYNC & V-SYNC signals counting,
Programmable SYNC signals output, free running signal generator. Pin52/Pin53 are for the H-SYNC and V-SYNC
input. and the polarity are setting in the positive. When no signal input, the Pin49 will output a 75Hz V-SYNC free
run signal. The Pin18/20will output a 60KHz H-SYNC free run signal. for the monitor testing use.
Reset Circuit(pin23)
There are three ways possible to invoke a reset and initialize the SAA4849 micro controller part:
Via power-on reset circuit
Via watchdog timer overflow(only micro controller reset)
Via deflection reset after start up(only micro controller reset)
The reset pin(pin23) is connected to a Schmitt trigger for nose reduction. A reset is accomplished by holding the
Reset pin HIGH.
RST Pin23
+
5V
C145
22U
R153
2.7K
22
C102
0.1UF
17” CDT Color Monitor
107B7
x-ray protection
The x-ray protection(pin22) input XRAY provides a voltage detector with a precise voltage input for X-ray
protection .If the input voltage at XRAY exceeds the upper threshold for 150us to 300us,the system is forced to
shut down by switching off vertical-and B-drive signals. There are two different ways to handle the system in case
of XRAY occurrence:
1. If the x-ray latch enable bit UCXRAY[2] was set to “0” during startup the system will shut down without any
interference of the uC.The deflection controller is set to ldle mode. Restart of the system only possible due to
seitching power off/power on.
2. If register bit UCXRAY[2] was set to “1”,micro controller interaction is allowed .If the micro controller doesn’t
interrupt the system, the system will shut down to ldle mode. For any interaction of the micro controller the XRAY
occurrence has to be acknowledged by the micro controller by clearing the bit SY-STATUS[2].The micro controller
take over the control of the handling via software. The actual x-ray pin status can be read through bit SY-STATUS[1].
Quartz Oscillator(pin45,pin46)
The quartz oscillator circuit is available on pins XTAL1(input) and XTAL2(output) and works together with an
external 48MHz 3rd overtone quartz. As a result the quartz oscillator is always running on 48MHz.Other quartz
crystal frequencies than 48 MHz cannot be used.External capacitors on XTAL1 and XTAL2 are not allowed.
B+ Control Function Block
The B+control block of the SAA4849 has the same behaviour as the TDA4856 with adapted threshol
voltages.The circuit allows the user to choose the trigger edge of the HDRV signal and the polarity of the output
stage via I2C-Bus.
The B+ control function block of the SAA4849 consists of an Operational Transconductance Amplifier(OTA), a
voltage comparator,a flip-flop and a discharge circuit. This configuration allows easy application for different B+
control concepts.
HPLL
The horizontal part contains a PLL,which works over the full frequency range from 25kHz to 140 kHz.This range
can be reduced by a ower and an upper frequency limit(Write Once Registers HPMAX and HPMIN).Via I2C bus the
number of 48MHz clock cycles is sent through the register. The slewing speed during mode change is also
programmable in a write once register (HSLEW)
After the clocks for the HPLL are switched on, the HPLL starts with a fixed freerunning frequency of 60 kHz.The
H-drive pulses are not active and the start up procedure is inhibited.The default setting of register bit HCONTROL [0]
2
will cause the HPLL to slew ,not switch.to the freerunning frequency defined in the I C register HPFREE( the default
value is also 60 kHz).Independent on H-syncs which are possibly present.the HPLL will slew to that freerunning
frequency. To achieve an always defined starting point for the startup procedure,this procedure cannot be interrupted.
23
17” CDT Color Monitor
107B7
5-2 Transistor & Diode and IC Circuit
Location
Description
Function
IC101
SAA4849PS
CPU
IC601
TDA4863A
Vertical Output IC
IC801
NT6812KG-20019
Video PreAmplifier/OSD IC
IC802
LM2476
Video Output IC
IC901
STR-G5643D
PWM Combi power MOS IC
IC902
L7805CV
DC to DC IC
C907
150UF/450V
Filter capacitance
Q911
IRF634B
B+ Transistor
Q403
2SC5909
Horizontal Output Transistor
Q406
IRF630M/S.T
Horizontal Size Transistor
Q410
2SC2120-Y
Horizontal linearity Transistor
D901~D904
1N5408 PEC
Crtical Safety Component
Q426/Q420/Q427 IRF630M/S.T
CS adjust Transistor
D919
F R D 3A/400V 31DF4/I.R
Rectifier DIODE
D922
RG-4S
Rectifier DIODE
D923
RG-4S
Rectifier DIODE
D925
RG-4S
Rectifier DIODE
D408
DMV1500MFD
Rectifier DIODE
C961
3300PF 250VAC/400VAC
Crtical Safety Component
C962/C963/
C964
3300PF 250VAC/400VAC
Crtical Safety Component
24
17” CDT Color Monitor
107B7
6. Mechanical Instructions
0. General
To be able to perform measurements and repairs on the "circuit boards", these unit should be placed
in the service position first.
1. Remove the rear cover
Remove 3 screws as shown in Fig. 1 and Fig. 2
Fig. 2
Fig. 1
2. Video board
Cut the tip on the front frame as show in Fig. 3
Disconnect the adhesive tape and ground pins
between metal shield of Video board and main
board as shown in Fig. 4 to Fig. 7
Cut the tie between the CRT neck and the video
board as shown in Fig. 8
Fig. 3
Fig. 4
Fig. 5
25
Fig. 6
17” CDT Color Monitor
107B7
Fig. 7
Fig. 8
3. Main panel
Disconnect the rotation coil from Main
board as shown in Fig. 9
Disconnect the degaussing coil and ground-screw
from Main board as shown in Fig. 10.
Disconnect the BY coil from Main board
as shown in Fig. 11.
Disconnect the key board connector P102 from
Main board as shown in Fig. 12
Disconnect the ground pins from Main board
as shown in Fig. 13
Fig. 9
Disconnect the Hi-Pot cap between the CRT and
Main board as show in Fig. 14.
Fig. 10
Fig. 11
26
Fig. 12
17” CDT Color Monitor
107B7
Fig. 13
Fig. 14
4. Remove Main board
Fig. 15
5. Remove Front frame
Remove four screws as show in Fig. 16
Fig. 17
Fig. 16
27
17” CDT Color Monitor
107B7
7.Trouble Shooting Chart
7-1 No Raster
1.CRT Relative Circuit Problems
CHECK MAIN PCB POWER SUPPLY
56V, 14V, 80V, 7V(80V FROM FBT)
CHECK POWER SAVING CIRCUIT,
NG
H-SYNC, V-SYNC SIGNAL
Q907, Q908, Q909, Q910
OK
OK
CHECK THE HIGE VOLTAGE
REFER ITEM S.M.P.S.
OF CRT ABOUT 21.0~ 22.8KV
NG
CHECK IC101 PIN18 OUTPUT
OK
CHECK THE VOLTAGE OF CRT
HEATER ABOUT 6.3V
CHECK CRT'S HEATER RELATIVE
NG
OK
CIRCUIT Q907, Q908
CHECK SCREEN VOLTAGE ABOUT
400V TO 600V
LESS THAN 300V
CHECK FBT
OK
BRIGHTNESS SET TO MAX. THEN
CHECK CRT G1 VOLTAGE
CHECK BRIGHTNESS CIRCUIT
NG
Q705 RELATIVE CIRCUIT
OK
CHECK VOLTAGE OF THE CRT
CATHODE ABOUT 56V TO 65V
REFER ITEM 6-2
NG
"ABNORMAL DISPLAY"
28
17” CDT Color Monitor
107B7
2.Abnormal Video Level On Screen
CHECK THE VOLTAGE OF IC801
PIN 10, 18 ABOUT 5V
NG
CHECK 5V RELATIVE CIRCUIT
OK
CHECK THE SIGNAL INPUT OF R.G.B.
ABOUT 0.7Vpp
CHECK SIGNAL CABLE OR
INTERFACE CARD.
OK
CHECK IC801 PIN 23 CLAMP PULSE
NG
CHECK THE IC801 PIN 23
OK
CHECK THE VIDEO OUTPUT OF IC801
RELATIVE CIRCUIT
PIN 19, 20, 21 ABOUT 4Vpp,
CONTRAST SET MAX.
NG
CHECK IC801 PIN19/PIN20/PIN21
OK
RELATIVE CIRCUIT
R.G.B. APPROACH STANDARD
3. Abnormal DDC (Plug & Play)
CHECK IC101 PIN 5 VOLTAGE ABOUT 5V
NG
CHECK IC902 GOOD OR FAIL
OK
CHECK SIGNAL CABLE
OR H802 PIN 2, 4 DATA OUTPUT
29
17” CDT Color Monitor
107B7
7-2. Abnormal Display
No Signal On Screen
CHECK VIDEO IC801 VCC ABOUT 5V
NG
CHECK THE 5V PIN
OF P802 CONNECTOR
OK
CHECK THE OUTPUT VOLTAGE
OF IC801 PIN 19, 20, 21 ABOUT 3Vpp
NG
CHECK THE RELATIVE CIRCUIT
OK
OF IC801 PIN 10/PIN 18 Vcc CIRCUIT
CHECK THE VOLTAGE OF
VIDEO AMP ABOUT 80V
CHECK THE 80V RELATIVE CIRCUIT
NG
ON MAIN PCB
OK
CHECK THE VOLTAGE OF CRT
CATHODE ABOUT 40Vpp
NG
CHECK THE IC802
RELATIVE CIRCUIT
OK
CHECK THE VOLTAGE OF FBT SCREEN
ABOUT 400V TO 700V
LESS THAN 400V
CHECK FBT RELATIVE CIRCUIT
EXCEED 700V
CHECK FBT & CRT RELATIVE
CIRCUIT OR REFER ITEM 6-1
30
17” CDT Color Monitor
107B7
7-3. No Blanking
CHECK THE RELATIVE
CIRCUIT OF BLANKING
CHECK THE RELATIVE CIRCUIT
NG
OK
OF FBT
CHECK R821 ON VIDEO PCB,
CHECK G1 RELATIVE CIRCUIT
FBT PIN 5 ON MAIN PCB
7-4.
Hor./Osc/Def/Hv Circuit Fault
No Raster (Disconnect With Signal Cable)
CHECK IC101 PIN 16 ABOUT 5 VDC
NG
CHECK IC101 PIN 5 RELATIVE CIRCUIT
OK
CHECK IC101 PIN20 WAVE FORM
ABOUT 3Vpp
CHECK IC101 PIN20
NG
RELATIVE CIRCUIT
OK
CHECK THE COLLECTOR VOLTAGE
OF Q402 ABOUT 14Vpp
CHECK Q402, T401
NG
OK
RELATIVE CIRCUIT
CHECK THE COLLECTOR VOLTAGE
OF Q403 ABOUT 1200Vpp AT FH: 31KHz
CHECK T401, T402, Q402, Q403,
NG
D408, C418, C419, H-DY, B+
31
17” CDT Color Monitor
107B7
7-5. Abnormal Horizontal Deflection
1.Abnormal Horizontal Width Of Video
READJUST H-WIDTH FUNCTION
CHECK THE RELATIVE CIRCUIT
NG
OFQ406
OK
CHECK FBT B+ VOLTAGE
ABOUT 62V AT FH=31KHz
NG
CHECK THE RELATIVE
CIRCUIT OF SMPS.
OK
CHECK THE HV OF
CRT ABOUT 25KV
2.Abnormal Horizontal Linearity
CHECK L401, Q426, Q420, Q427
AND IC101 PIN9, 10,11
32
17” CDT Color Monitor
107B7
7-6 Abnormal Vertical Scanning
1. Abnormal Vertical Size
READJUST V-SIZE FUNCTION VALUE
CHECK THE IC601 PIN1 ABOUT 11.8V
PIN 4 ABOUT -12V
CHECK D601, C605
NG
RELATIVE CIRCUIT
OK
CHECK VERT. OSC CIRCUIT
NG
CHECK THE VOLTAGE OF IC101
RELATIVE CIRCUIT
OK
READJUST V-SIZE FUNCTION VALUE
NG
CHECK IC101 PIN33, 34
RELATIVE CIRCUIT
2. Vertical Center
READJUST V-CENTER
NG
CHECK IC101 AND IC601
RELATIVE CKT
7-7. Side-Pin Cushion Distortion
READJUST SIDEPIN
NG
CHECK IC101, Q406
RELATIVE CKT.
7-8. Poor Focus
READJUST FOCUS CONTROL
CHECK FOCUS CONTROL UNIT,
NG
FOCUS LEAD WIRE, CRT SOCKET & CRT
33
17” CDT Color Monitor
107B7
7-9. Power Supply Trouble Shooting Chart
BEFORE CHECK SW.REG. PLEASE REFER TO THE POWER SUPPLY BLOCK DIAGRAM
POWER SUPPLY OUTPUT: (A) VARIABLE OUTPUT : 60V – 154.5V
(DEPENDING EPENDING UPON H.SYNC FREQUENCY)
(B) CONSTANT OUTPUT : 6.3V, 14V,80V
BEAD SET
ABNORMAL VARIABLE OUTPUT
MAKE SURE
NG
THAT
THE
VARIABLE OUTPUT IS NOT
CHECK AC LINE
VOLT 120V OR 220V
SHORTED
CHECK F901, SW901
OK
NO
CHECK
IC101
CHECK LINE RECTIFIED &
YES
SMOOTHED VOLT
CHECK THE 56V OUTPUT
NG
CHECK BRIDGE
RECTIFIED CIRCUIT
OK
NG
CHECK START C.K.T
CHECK D925
R939, R940, D912, ZD903
OK
CHECK Q911
NG
OK
CHECK T901 O/P
OK
IC101 PIN30 (ABOUT5V)
NG
CHECK 56V, 14.5V
6.5V CIRCUIT OUTPUT
OK
OK
CHECK IC901
NG
IC901 FAILURE
OK
CHECK SENSE RESISTENCE
34
PIN39,
40,41, B+ DRIVER
Q911 FAILURE
17” CDT Color Monitor
107B7
8. Mechanical of cabinet front dis-assembly
35
17” CDT Color Monitor
107B7
9. Spare parts List
107B70/00
PCB
Part No. for TPV
CMB784B1T9EP1P
CKB784B1TP1P
CRB784B1T9P1P
Description
CHASSIS FOR P784B3-1 PHILIPS POH
KEPC FOR B784B3-1 PHILIPS
CRT BOARD P784B3-1 PHILIPS ROHS
Philips P/N (12NC)
9965 000 35708
9965 000 35711
9965 000 35739
Part No. for TPV
750C5X301AV
Description
CPT 17" RF 0.13 ES CRT
Philips P/N (12NC)
9965 000 35707
Description
Philips P/N (12NC)
9965 000 35698
9965 000 35395
9965 000 35699
9965 000 35700
9965 000 35701
9965 000 35702
9965 000 35400
9965 000 35401
9965 000 35705
9965 000 35706
9965 000 35402
9965 000 35403
9965 000 35404
9965 000 35406
9965 000 35410
9965 000 35411
9965 000 35412
9965 000 35711
9965 000 35708
9965 000 35709
9965 000 35712
9965 000 35710
9965 000 35418
9965 000 35432
9965 000 35459
9965 000 35724
9965 000 28173
9965 000 35725
9965 000 35733
Panel
Accessory and Mechanical
Part No. for TPV
033C6411VET
033C64121
034C6376BVCT
034C6377VCT
034C6378VCB
034C6379VCB
040C58162435A
040C5818131A
044C60027165A
044C60028347A
044C67F71
044C67F72
045C7628RN
045C887RN
095C2070516
095C2070532
750A1697504JAG
CKB784B1TP1P
CMB784B1T9EP1P
Q40C70B8132B
Q41C6881312A
Q44C67F78132B
Q70CD7988131B
089C71F5TYHG3
040C5816242B
071C1002S
071C1008
071C1009
087C5016
KEY PAD
LENS
FRONT PANEL
BACK COVER
SWIVEL
BASE
MANUAL P/N LABEL
CARTON LABEL
PAPER PLATE
PAPER BOARD
EPS CUSHZON
EPS CUSHZON
PE BAG FOR MANUAL
MONITOR PE BAG
WIRE HARNESS
WIRE HARNESS
DEGAUSSING COIL
KEPC FOR B784B3-1 PHILIPS
CHASSIS FOR P784B3-1 PHILIPS POH
RATING LABEL
QSG
CARTON
CD MANUAL
SIGNAL CABLE D-SUB HONGLIN
CHASSIS LABEL
CORE 8*16*12
FERRITE CORE 12*25*15
FERRIRE CORE 28.5*17.5*9.5
AC SOCKET
36
17” CDT Color Monitor
005C711
084C3310
040C45762412B
087C3504ZW
107B7
TRANSISTOR HOUSING
FUSE CLIP
LABEL
CRT SOCKET(QQ FOCUS)
9965 000 35735
9965 000 35535
9965 000 35538
9965 000 35877
Main Board
Location
H803
CN903
P901
IC902
IC101
IC102
Q909
Q907
PR901
R607
R927
R907
R724
R446
R911
R929
R407
R963
R912
R916
R456
C901
C427
C425
C419
C418
C482
C426
C422
C919
C924
C925
C961
C963
C962
C964
C401
C931
C605
Part No. for TPV
CMB784B1T9EP1P
033C32787D
033C38033
033C80093X
040C5816242B
056C1335ST
056C1125575X
056C11332PH
057C20151A
057C20151A
061C52274J
061C20810964
061C20833364
061C20868164
061C152M10064
061C152M10064
061C152M10164
061C152M20864
061C152M22064
061C152M22864
061C152M82964
061C153M13259
061C153M27159
063C107K104U
063C210J1242CC
063C210J2443CU
063C210J3027CC
063C210J4727FC
063C210J6842CU
063C210J7542CC
064C100J22559
065C2M1033B692
065C2M1033FB69
065C2M1033FB69
065C305M3322B2
065C305M3322B2
065C305M3322B2
065C305M3322B2
067C2151024
067C2152219J
067C3051023
Description
CHASSIS FOR P784B3-1 PHILIPS POH
WAFER*PLUG
WAFER EH-E
2 PIN
CHASSIS LABEL
L7805CV
SAA4849PS
M24C16-WBN6/P
2SB772-P
2SB772-P
PTCR
MOFR 1 OHM -5% 1W
MOFR 33K OHM -5% 1W
MOFR 680 OHM -5% 1W
MOFR 10 OHM -5% 2W
MOFR 10 OHM -5% 2W
MOFR 100OHM -5% 2W
0.20 OHM 2W
22 OHM -5% 2W
MOFR 0.22 OHM -5% 2W
MOFR 8.2 OHM -5% 2W
1.3KOHM 3W
MOFR 270 OHM -5% 3W
100NF, 275VAC,X2, K
0.12UF 250V
0.24UF 400V
3000PF 1600V
4700PF 1.6KV
0.68UF 250V
0.75UF 250V
2.2UF -5% 100V
0.01UF 2KV 20% Z5U
10000PF -20%~ 18% 2KV
10000PF -20%~ 18% 2KV
3.3NF,400VAC, Y2, M
3.3NF,400VAC, Y2, M
3.3NF,400VAC, Y2, M
3.3NF,400VAC, Y2, M
1000UF -20% 25V
220UF -20% 100V JAMICON
1000 UF -20% 16V
37
Philips P/N (12NC)
9965 000 35708
9965 000 35713
9965 000 35714
9965 000 35715
9965 000 35459
9965 000 35460
9965 000 35461
9965 000 35462
9965 000 35464
9965 000 35464
9965 000 35465
9965 000 35466
9965 000 35468
9965 000 35469
9965 000 35471
9965 000 35471
9965 000 35472
9965 000 35473
9965 000 35474
9965 000 35475
9965 000 35476
9965 000 35477
9965 000 35716
9965 000 35717
9965 000 35718
9965 000 35719
9965 000 35720
9965 000 35721
9965 000 35484
9965 000 35722
9965 000 35485
9965 000 35487
9965 000 35488
9965 000 35488
9965 000 35489
9965 000 35489
9965 000 35489
9965 000 35489
9965 000 35490
9965 000 35491
9965 000 35492
17” CDT Color Monitor
C939
C936
C937
C603
C402
C907
CF962
CF963
FB404
FB902
L901
L401
L902
L405
L906
VR902
RY901
T402
T403
T401
T901
D910
D925
D923
D922
SS1
H802
IC901
NR901
CN901
Q426
Q427
Q420
IC601
Q406
Q403
D408
D919
X101
Q911
E750A
067C3051023
067C3051024
067C3051024
067C3091023
067C30947010
067C40D15115P
071C552A
071C552A
071C5529
071C55503
071C1002S
071C1008
071C1009
073A1747G6906
073C147527TB
073C174502HC
073C253103HP
073C253103HP
075A334201
077C26054
079A793504CDG
079C167124H
079C167125T
080AS7742N4G
093C6026W52T
093C30408AT
093C30408AT
093C30408AT
095C205T3005A
095C801314632
056C379504
061C588TL
087C5016
095C80022G
057C60021
057C60021
057C60021
005C711
056C5841A
057C60021
057C706504
093C220512
093C6073A
093C2248H
057C60027
750C5X30784MPH
AMB784B1TP1P
CRB784B1T9P1P
084C3310
107B7
1000 UF -20% 16V
1000UF -20% 25V
1000UF -20% 25V
1000UF -20% 16V
47UF 160V -20%
150UF -20% 450V
FERRITE BEAD 3*5*1.5
FERRITE BEAD 3*5*1.5
FERRITE BEAD
FERRITE BEAD
CORE 8*16*12
FERRITE CORE 12*25*15
FERRIRE CORE 28.5*17.5*9.5
LINE CHOKE
LINEARITY COIL
LINE FILTER
CHOKE COIL
CHOKE COIL
CFVR 200 OHM -20%
RELAY
BAILI FBT
DRIVER TRANSFORMER
DRIVE TRANSFORMER
TRANSFORMER YUVA
FR107
RG-4S
RG-4S
RG-4S
WIRE
WIRE HARNESS
STR-G5643D
NTCR 15OHM -15%2.5A THINKING
AC SOCKET
WIRE&CORE
IRF630M/S.T
IRF630M/S.T
IRF630M/S.T
TRANSISTOR HOUSING
TDA4863A/PHILIPS
IRF630M/S.T
2SC5909
DMV1500MFD
F R D 3A/400V 31DF4/I.R
48MHZ
IRF634B
17" CPT CRT MPRII ASS'Y
MAIN BOARD B784B3-1 PHILIPS
CRT BOARD P784B3-1 PHILIPS ROHS
FUSE CLIP
38
9965 000 35492
9965 000 35493
9965 000 35493
9965 000 35496
9965 000 35723
9965 000 35497
9965 000 35499
9965 000 35499
9965 000 35500
9965 000 35501
9965 000 35724
9965 000 28173
9965 000 35725
9965 000 35502
9965 000 35726
9965 000 35728
9965 000 35727
9965 000 35727
9965 000 35506
9965 000 35507
9965 000 35729
9965 000 35509
9965 000 35730
9965 000 35731
9965 000 35512
9965 000 35513
9965 000 35513
9965 000 35513
9965 000 35514
9965 000 35515
9965 000 35516
9965 000 35732
9965 000 35733
9965 000 35734
9965 000 35518
9965 000 35518
9965 000 35518
9965 000 35735
9965 000 35520
9965 000 35518
9965 000 35736
9965 000 35522
9965 000 35523
9965 000 35527
9965 000 35524
9965 000 35737
9965 000 35738
9965 000 35739
9965 000 35535
17” CDT Color Monitor
F901
R426
R428
C423
C480
C488
C489
R429
R969
R725
R939
R940
R702
R420
NR601
R421
R422
R425
R909
R980
R970
R958
R418
R915
R447
R161
R416
R705
R716
R405
R463
R918
R960
R417
R444
R448
R487
R903
R962
R906
R951
R603
R601
R721
R486
R461
R460
R412
084C7H400SL
750C5X301AV
061C153M36059
061C153M75859
063C210J3342CU
065C1K4705T605
065C2K1215A692
065C2K1815T
061A212Y10052T
061A212Y20352T
061A212Y27452T
061A212Y39452T
061A212Y47452T
061A212Y62152T
061A214Y24452T
061C58450UT
061C17210052T
061C17210052T
061C17210152T
061C17210152T
061C17210252T
061C17210252T
061C17210252T
061C17210352T
061C17210452T
061C17212252T
061C17212452T
061C17212452T
061C17215152T
061C17216452T
061C17218252T
061C17220552T
061C17222152T
061C17222352T
061C17230352T
061C17233252T
061C17233252T
061C17233252T
061C17243052T
061C17247052T
061C17247052T
061C17247152T
061C17247152T
061C17247152T
061C17247252T
061C17247252T
061C17247252T
061C17247252T
061C17247352T
107B7
FUSE 4A 250V LF-618 004
CPT 17" RF 0.13 ES CRT
36 OHM 3W
MOFR 0.75 OHM -5% 3W
0.33UF 250V
47P/1KV
120PF 2KV
180PF 2KV
10 OHM 1/2W
20K OHM -5% 1/2W
MGFR 270K OHM -5% 1/2W
390KOHM 1/2W
MGFR 470KOHM -5% 1/2W
620 OHM 1/2W
MGFR 240K OHM -5% 1/4W
NTCR 45OHM -15%3100K UPPERMOST
CFR 10OHM -5% 1/4W
CFR 10OHM -5% 1/4W
CFR 100OHM -5% 1/4W
CFR 100OHM -5% 1/4W
CFR 1KOHM -5% 1/4W
CFR 1KOHM -5% 1/4W
CFR 1KOHM -5% 1/4W
CFR 10KOHM -5% 1/4W
CFR100K OHM -5% 1/4W
CFR 1.2K OHM -5% 1/4W
CFR 120K OHM -5% 1/4W
CFR 120K OHM -5% 1/4W
CFR 150 OHM -5% 1/4W
CFR 160KOHM -5% 1/4W
CFR 1.8K OHM -5% 1/4W
CFR 2MOHM -5% 1/4W
CFR 220OHM -5% 1/4W
CFR 22KOHM -5% 1/4W
CFR 30KOHM -5% 1/4W
CFR 3.3KOHM -5% 1/4W
CFR 3.3KOHM -5% 1/4W
CFR 3.3KOHM -5% 1/4W
CFR 43 OHM -5% 1/4W
CFR 47 OHM -5% 1/4W
CFR 47 OHM -5% 1/4W
CFR 470OHM -5% 1/4W
CFR 470OHM -5% 1/4W
CFR 470OHM -5% 1/4W
CFR 4.7K OHM -5% 1/4W
CFR 4.7K OHM -5% 1/4W
CFR 4.7K OHM -5% 1/4W
CFR 4.7K OHM -5% 1/4W
CFR 47K OHM -5% 1/4W
39
9965 000 35536
9965 000 35707
9965 000 35881
9965 000 35470
9965 000 35882
9965 000 35883
9965 000 35884
9965 000 35885
9965 000 35744
9965 000 35745
9965 000 35747
9965 000 35748
9965 000 35749
9965 000 35750
9965 000 35751
9965 000 35752
9965 000 35753
9965 000 35753
9965 000 35754
9965 000 35754
9965 000 35755
9965 000 35755
9965 000 35755
9965 000 35756
9965 000 35757
9965 000 35758
9965 000 35759
9965 000 35759
9965 000 35544
9965 000 35760
9965 000 35761
9965 000 35762
9965 000 35746
9965 000 35763
9965 000 35764
9965 000 35765
9965 000 35765
9965 000 35765
9965 000 35766
9965 000 35767
9965 000 35767
9965 000 35768
9965 000 35768
9965 000 35768
9965 000 35769
9965 000 35769
9965 000 35769
9965 000 35769
9965 000 35770
17” CDT Color Monitor
R133
R965
R707
R715
R150
R449
R147
R930
R403
R749
R941
R137
R138
R110
R111
R103
R120
R118
R117
R105
R104
R149
R152
R172
R167
R165
R159
R132
R143
R145
R148
R122
R102
R101
R124
R139
R415
R126
R130
R144
R902
R921
R933
R952
R953
R959
R982
R983
R140
061C17247452T
061C17247952T
061C17256252T
061C17256352T
061C17256352T
061C17262252T
061C17262352T
061C17268152T
061C17268352T
061C17268352T
061C17275152T
061C17275352T
061C17275352T
061C60210052T
061C60210052T
061C60210152T
061C60210152T
061C60210152T
061C60210152T
061C60210152T
061C60210152T
061C60210152T
061C60210152T
061C60210152T
061C60210152T
061C60210152T
061C60210152T
061C60210152T
061C60210152T
061C60210152T
061C60210152T
061C60210152T
061C60210152T
061C60210152T
061C60210252T
061C60210252T
061C60210252T
061C60210352T
061C60210352T
061C60210352T
061C60210352T
061C60210352T
061C60210352T
061C60210352T
061C60210352T
061C60210352T
061C60210352T
061C60210352T
061C60212152T
107B7
CFR 470K OHM -5% 1/4W
CFR 4.7 OHM -5% 1/4W
CFR 5.6K OHM -5% 1/4W
CFR 56K OHM -5% 1/4W
CFR 56K OHM -5% 1/4W
CFR 6.2K OHM -5% 1/4W
CFR 62K OHM -5% 1/4W
CFR 680 OHM -5% 1/4W
CFR 68K OHM -5% 1/4W
CFR 68K OHM -5% 1/4W
750OHM 1/4W
CFR 75K OHM -5% 1/4W
CFR 75K OHM -5% 1/4W
CFR 10 OHM -5% 1/6W
CFR 10 OHM -5% 1/6W
CFR 100 OHM -5% 1/6W
CFR 100 OHM -5% 1/6W
CFR 100 OHM -5% 1/6W
CFR 100 OHM -5% 1/6W
CFR 100 OHM -5% 1/6W
CFR 100 OHM -5% 1/6W
CFR 100 OHM -5% 1/6W
CFR 100 OHM -5% 1/6W
CFR 100 OHM -5% 1/6W
CFR 100 OHM -5% 1/6W
CFR 100 OHM -5% 1/6W
CFR 100 OHM -5% 1/6W
CFR 100 OHM -5% 1/6W
CFR 100 OHM -5% 1/6W
CFR 100 OHM -5% 1/6W
CFR 100 OHM -5% 1/6W
CFR 100 OHM -5% 1/6W
CFR 100 OHM -5% 1/6W
CFR 100 OHM -5% 1/6W
CFR 1K OHM -5% 1/6W
CFR 1K OHM -5% 1/6W
CFR 1K OHM -5% 1/6W
CFR 10K OHM -5% 1/6W
CFR 10K OHM -5% 1/6W
CFR 10K OHM -5% 1/6W
CFR 10K OHM -5% 1/6W
CFR 10K OHM -5% 1/6W
CFR 10K OHM -5% 1/6W
CFR 10K OHM -5% 1/6W
CFR 10K OHM -5% 1/6W
CFR 10K OHM -5% 1/6W
CFR 10K OHM -5% 1/6W
CFR 10K OHM -5% 1/6W
CFR 120 OHM -5% 1/6W
40
9965 000 35771
9965 000 35772
9965 000 35773
9965 000 35774
9965 000 35774
9965 000 35775
9965 000 35776
9965 000 35777
9965 000 35778
9965 000 35778
9965 000 35779
9965 000 35780
9965 000 35780
9965 000 35781
9965 000 35781
9965 000 35549
9965 000 35549
9965 000 35549
9965 000 35549
9965 000 35549
9965 000 35549
9965 000 35549
9965 000 35549
9965 000 35549
9965 000 35549
9965 000 35549
9965 000 35549
9965 000 35549
9965 000 35549
9965 000 35549
9965 000 35549
9965 000 35549
9965 000 35549
9965 000 35549
9965 000 35550
9965 000 35550
9965 000 35550
9965 000 35551
9965 000 35551
9965 000 35551
9965 000 35551
9965 000 35551
9965 000 35551
9965 000 35551
9965 000 35551
9965 000 35551
9965 000 35551
9965 000 35551
9965 000 35782
17” CDT Color Monitor
R610
R106
R751
R602
R114
R113
R484
R445
R443
R158
R720
R157
R156
R131
R109
R108
J066
R984
R153
R713
R116
R134
R119
R112
R115
R125
R433
R154
R151
R129
R135
R107
R123
R957
R905
R748
R142
R961
R146
R910
R413
R472
R471
R419
R478
R477
R476
R410
R981
061C60213152T
061C60215352T
061C60218252T
061C60218252T
061C60218252T
061C60218252T
061C60220352T
061C60220352T
061C60220352T
061C60220352T
061C60222252T
061C60222252T
061C60222252T
061C60222252T
061C60222252T
061C60222252T
061C60224252T
061C60227252T
061C60227252T
061C60233252T
061C60239252T
061C60239252T
061C60247052T
061C60247052T
061C60247152T
061C60247152T
061C60247152T
061C60247152T
061C60247152T
061C60247152T
061C60247152T
061C60247252T
061C60247252T
061C60247352T
061C60262252T
061C60268252T
061C60282252T
061C60282252T
061C60282252T
061C60291352T
061C172S10052T
061C172S10452T
061C172S10452T
061C172S10452T
061C172S22452T
061C172S22452T
061C172S22452T
061C175L10052T
061C175L10152T
107B7
CFR 130 OHM -5% 1/6W
CFR 15K OHM -5% 1/6W
CFR 1.8K OHM -5% 1/6W
CFR 1.8K OHM -5% 1/6W
CFR 1.8K OHM -5% 1/6W
CFR 1.8K OHM -5% 1/6W
CFR 20K OHM -5% 1/6W
CFR 20K OHM -5% 1/6W
CFR 20K OHM -5% 1/6W
CFR 20K OHM -5% 1/6W
CFR 2.2K OHM -5% 1/6W
CFR 2.2K OHM -5% 1/6W
CFR 2.2K OHM -5% 1/6W
CFR 2.2K OHM -5% 1/6W
CFR 2.2K OHM -5% 1/6W
CFR 2.2K OHM -5% 1/6W
CFR 2.4K OHM -5% 1/6W
CFR 2.7K OHM -5% 1/6W
CFR 2.7K OHM -5% 1/6W
CFR 3.3K OHM -5% 1/6W
CFR 3.9K OHM -5% 1/6W
CFR 3.9K OHM -5% 1/6W
CFR 47 OHM -5% 1/6W
CFR 47 OHM -5% 1/6W
CFR 470 OHM -5% 1/6W
CFR 470 OHM -5% 1/6W
CFR 470 OHM -5% 1/6W
CFR 470 OHM -5% 1/6W
CFR 470 OHM -5% 1/6W
CFR 470 OHM -5% 1/6W
CFR 470 OHM -5% 1/6W
CFR 4.7K OHM -5% 1/6W
CFR 4.7K OHM -5% 1/6W
CFR 47K OHM -5% 1/6W
CFR 6.2K OHM -5% 1/6W
CFR 6.8K OHM -5% 1/6W
CFR 8.2K OHM -5% 1/6W
CFR 8.2K OHM -5% 1/6W
CFR 8.2K OHM -5% 1/6W
CFR 91K OHM -5% 1/6W
RES CF 5% 1/4W 100HM AX
CFR 100 KOHM -5% 1/4WS
CFR 100 KOHM -5% 1/4WS
CFR 100 KOHM -5% 1/4WS
220K 1/4W
220K 1/4W
220K 1/4W
CFR 10 OHM -5% 1/2W
CFR 100 OHM -5% 1/2W
41
9965 000 35783
9965 000 35784
9965 000 35785
9965 000 35785
9965 000 35785
9965 000 35785
9965 000 35786
9965 000 35786
9965 000 35786
9965 000 35786
9965 000 35787
9965 000 35787
9965 000 35787
9965 000 35787
9965 000 35787
9965 000 35787
9965 000 35742
9965 000 35788
9965 000 35788
9965 000 35553
9965 000 35789
9965 000 35789
9965 000 35790
9965 000 35790
9965 000 35791
9965 000 35791
9965 000 35791
9965 000 35791
9965 000 35791
9965 000 35791
9965 000 35791
9965 000 35554
9965 000 35554
9965 000 35792
9965 000 35793
9965 000 35794
9965 000 35795
9965 000 35795
9965 000 35795
9965 000 35796
9965 000 35797
9965 000 35798
9965 000 35798
9965 000 35798
9965 000 35799
9965 000 35799
9965 000 35799
9965 000 35800
9965 000 35559
17” CDT Color Monitor
R723
R901
R606
R605
R741
R750
R740
R908
R604
R608
C920
FB403
FB907
FB402
FB901
ZD903
ZD109
ZD902
ZD703
ZD105
ZD108
D901
D902
D903
D904
D601
D407
D406
D464
D463
D474
D706
D104
D939
D708
D916
D450
D912
D101
D405
D740
D404
D929
D911
D403
Q401
Q901
Q412
Q913
061C175L10252T
061C175L10552T
061C175L12152T
061C175L15952T
061C175L43452T
061C175L51952T
061C175L56352T
061C175L75952T
061C175S18252T
061C175S27152T
064C45G4711AT
071C559T
071C559T
071C559T
071C5519T
093C395852T
093C397352T
093C397352T
093C3950252T
093C3952152T
093C3953052T
093C529T52T
093C529T52T
093C529T52T
093C529T52T
093C5247T52T
093C6021P52T
093C6021P52T
093C6026T52T
093C6026W52T
093C6026W52T
093C6044T52T
093C641152T
093C641152T
093C641152T
093C641152T
093C641152T
093C6431P52T
093C10021W52T
093C10021W52T
093C1040252T
093C1040252T
093C1040252T
093C106050652T
093C2020552T
057C417503T
057C417503T
057C419PPT
057C419503T
107B7
CFR 1K OHM -5% 1/2W
CFR 1M OHM -5% 1/2W
CFR 120 OHM -5% 1/2W
CFR 1.5 OHM -5% 1/2W
CFR 430K OHM -5% 1/2W
MOFR 5.1 OHM -5% 1/2W
CFR 56K OHM -5% 1/2W
CFR 7.5 OHM -5% 1/2W
CFR 1.8K OHM -5% 1/2W
270 OPHM 1/2W
470PF -20% 100V
CORE RF BEAD RH 3.5X6X0.76TP
CORE RF BEAD RH 3.5X6X0.76TP
CORE RF BEAD RH 3.5X6X0.76TP
FERRITE BEAD 9X3.5X0.8
HZ24-2-E
HZ6B1-E
HZ6B1-E
HZ18-1-E
TZX18B
TZX5V6D
2A 600V 2A05
2A 600V 2A05
2A 600V 2A05
2A 600V 2A05
1N4004
PS156R
PS156R
RECTIFIER DIODE FR107
FR107
FR107
RECTIFIER DIODE FR157S
1N4148
1N4148
1N4148
1N4148
1N4148
BAV20
1N5817
1N5817
UF4004
UF4004
UF4004
DIODE
ER202
2N3904
2N3904
2PC945
2SC945P
42
9965 000 35801
9965 000 35802
9965 000 35803
9965 000 35804
9965 000 35805
9965 000 35806
9965 000 35807
9965 000 35808
9965 000 35809
9965 000 35810
9965 000 35811
9965 000 35562
9965 000 35562
9965 000 35562
9965 000 35812
9965 000 35813
9965 000 35815
9965 000 35815
9965 000 35816
9965 000 35817
9965 000 35814
9965 000 35818
9965 000 35818
9965 000 35818
9965 000 35818
9965 000 35819
9965 000 35566
9965 000 35566
9965 000 35820
9965 000 35512
9965 000 35512
9965 000 35821
4822 130 30621
4822 130 30621
4822 130 30621
4822 130 30621
4822 130 30621
9965 000 35822
9965 000 35823
9965 000 35823
9965 000 35824
9965 000 35824
9965 000 35824
9965 000 35825
9965 000 35826
9965 000 35827
9965 000 35827
9965 000 35828
9965 000 35829
17” CDT Color Monitor
Q910
Q908
Q906
Q903
Q423
Q411
Q905
Q912
Q743
Q410
Q902
Q742
Q705
Q402
C415
C116
C433
C710
C414
C601
C117
C413
C921
C608
C417
C720
C916
C922
C412
C107
C110
C121
C122
C131
C105
C106
C130
C128
C109
C124
C705
C127
C114
C123
C956
C908
C410
C120
C103
057C419503T
057C419503T
057C419503T
057C419503T
057C419503T
057C419503T
057C420502T
057C420502T
057C446500T
057C446501T
057C446501T
057C49312T
057C4983T
057C530503T
064C44J4721AT
064C45G2221AT
064C176J1041T
064C176J1231T
064C176J4740T
064C178J1020T
064C178J1031T
064C178J1040T
064C178J1041T
064C178J1041T
064C178J2240T
065C1K4715T692
065C1K4715T692
065C2K1015T692
065C2K2215T692
065C44210113T
065C44210113T
065C44210113T
065C44210113T
065C44233013T
065C4441025T
065C4441025T
065C4441025T
065C4441025T
065C4442225T
065C4442225T
065C4443325T
065C44447213T
065C4448215T
065C4501037T
065C4501043T
065C4501043T
065C4501043T
065C4501043T
065C4501043T
107B7
2SC945P
2SC945P
2SC945P
2SC945P
2SC945P
2SC945P
2SA733P
2SA733P
2SC1213C
2SC2120-Y
2SC2120-Y
BF420
HBF423
2SD1207T
4700PF 100V PEI
.0022UF -2% 100V
0.1UF 5% 100V
12NF 100V MPE
.47UF -5% 50/63V
1000PF -5% 63V
CL21X 0.01UF 100V -5%
CL21X0.1UF 63V -5%
C121X 0.1UF 100V -5%
C121X 0.1UF 100V -5%
0.22UF 63V. -5%
470PF -10% 1KV Y5P
470PF -10% 1KV Y5P
100PF/2KV
220PF 2000V
100PF -5% NPO 50V
100PF -5% NPO 50V
100PF -5% NPO 50V
100PF -5% NPO 50V
33PF -5% NPO 50V
1000 PF 10% 50V Y5P
1000 PF 10% 50V Y5P
1000 PF 10% 50V Y5P
1000 PF 10% 50V Y5P
2200PF 10% Y5P 50V
2200PF 10% Y5P 50V
3300PF 10% 50V Y5P
4700PF -10% Z5P 50V
820PF 10% Y5P 50V
10000PF/50V Y5V 80% -20%
0.1UF 50V Y5V
0.1UF 50V Y5V
0.1UF 50V Y5V
0.1UF 50V Y5V
0.1UF 50V Y5V
43
9965 000 35829
9965 000 35829
9965 000 35829
9965 000 35829
9965 000 35829
9965 000 35829
9965 000 35830
9965 000 35830
9965 000 35831
9965 000 35832
9965 000 35832
9965 000 35833
9965 000 35834
9965 000 35835
9965 000 35836
9965 000 35837
9965 000 35838
9965 000 35839
9965 000 35840
9965 000 35841
9965 000 35842
9965 000 35568
9965 000 35843
9965 000 35843
9965 000 35844
9965 000 35845
9965 000 35845
9965 000 35571
9965 000 35846
9965 000 35573
9965 000 35573
9965 000 35573
9965 000 35573
9965 000 35847
9965 000 35848
9965 000 35848
9965 000 35848
9965 000 35848
9965 000 35849
9965 000 35849
9965 000 35850
9965 000 35851
9965 000 35852
9965 000 35853
9965 000 35854
9965 000 35854
9965 000 35854
9965 000 35854
9965 000 35854
17” CDT Color Monitor
C102
C101
C112
C111
C431
C429
C411
C432
C430
C740
C910
C912
C713
C100
C609
C115
C940
C742
C119
C434
C113
C104
C118
C145
C483
ZD106
ZD103
ZD104
ZD101
ZD102
ZD901
ZD701
ZD711
ZD702
Key Board
Location
SW102
SW106
SW104
SW105
SW103
LED1
R191
R194
R192
R193
107B7
065C4501043T
065C4501043T
065C4501047T
065C4501047T
065C4501047T
065C4501047T
065C4501047T
065C517K1022T6
065C517K1525T6
065C517M1033T6
067C3052207T
067C3052297T
067C30522912T
067C3054703T
067C3054707T
067C3054787T
067C3054797T
067C3091003T
067C3091003T
067C3091007T
067C3091013T
067C3091013T
067C3091097T
067C3092204T
067C3094793T
093C397352T
093C3955452T
093C3955452T
093C3955452T
093C3955452T
093C3955652T
093C3955652T
093C3955652T
093C3955952T
0.1UF 50V Y5V
0.1UF 50V Y5V
0.1UF 80-20% 50V Y5V
0.1UF 80-20% 50V Y5V
0.1UF 80-20% 50V Y5V
0.1UF 80-20% 50V Y5V
0.1UF 80-20% 50V Y5V
1000PF 10% Z5P 500V
1.5NF/500V Y5P -10%
10NF 500V
22UF -20% 50V
2.2UF -20% 50V
2.2UF -20% 250V
47UF -20% 16V
47UF -20% 50V
0.47UF -20% 50V
4.7UF -20% 50V
10UF -20% 16V
10UF -20% 16V
10UF -20% 50V
100UF -20% 16V
100UF -20% 16V
1.0UF -20% 50V
22UF -20% 25V
4.7UF -20% 16V
HZ6B1-E
BZX79-B6V2
BZX79-B6V2
BZX79-B6V2
BZX79-B6V2
BZX79-B5V1
BZX79-B5V1
BZX79-B5V1
BZX79-C3VO
9965 000 35854
9965 000 35854
9965 000 35578
9965 000 35578
9965 000 35578
9965 000 35578
9965 000 35578
9965 000 35855
9965 000 35856
9965 000 35857
9965 000 35858
9965 000 35859
9965 000 35860
9965 000 35584
9965 000 35861
9965 000 35862
9965 000 35863
9965 000 35864
9965 000 35864
9965 000 35865
9965 000 35866
9965 000 35866
9965 000 35867
9965 000 35868
9965 000 35869
9965 000 35815
9965 000 35870
9965 000 35870
9965 000 35870
9965 000 35870
9965 000 35871
9965 000 35871
9965 000 35871
9965 000 35872
Part No for TPV
CKB784B1TP1P
077C6001GCJ
077C6001GCJ
077C6001GCJ
077C6001GCJ
077C6001GCJ
081C232P
061C60224252T
061C60224252T
061C60256252T
061C60256252T
Description
KEPC FOR B784B3-1 PHILIPS
TACT SWITCH TSPB-2-NP
TACT SWITCH TSPB-2-NP
TACT SWITCH TSPB-2-NP
TACT SWITCH TSPB-2-NP
TACT SWITCH TSPB-2-NP
LED
CFR 2.4K OHM -5% 1/6W
CFR 2.4K OHM -5% 1/6W
CFR 5.6KOHM -5% 1/6W
CFR 5.6KOHM -5% 1/6W
Philips 12NC
9965 000 35711
9965 000 35740
9965 000 35740
9965 000 35740
9965 000 35740
9965 000 35740
9965 000 35741
9965 000 35742
9965 000 35742
9965 000 35555
9965 000 35555
44
17” CDT Color Monitor
107B7
CRT Board
Location
G2
P801
P802
IC801
C852
C806
C844
C848
C811
C805
FB809
IC802
R815
R840
R829
R828
R844
R837
R819
R806
R810
R802
R805
R812
R813
R816
R814
R825
R845
R820
R832
R835
R836
R821
R818
R822
R811
R824
R826
R834
L809
Part No for TPV
CRB784B1T9P1P
009C2038
033C32786D
033C327814D
040C45762412B
056C366522
065C2M1033B692
065C2M1033FB69
065C44222013T
067C3051099T
067C3054709
067C3054709
071C5521
087C3504ZW
056C551525
ARB784B1TP1P
061C17220152T
061C17233052T
061C17233052T
061C17233052T
061C17233452T
061C17233452T
061C17233452T
061C21019252T
061C21033352T
061C60210152T
061C60210152T
061C60210252T
061C60210252T
061C60210252T
061C60210352T
061C60210352T
061C60210352T
061C60215152T
061C60215152T
061C60215152T
061C60233052T
061C60233052T
061C60233052T
061C60247252T
061C60256252T
061C60275052T
061C60275052T
061C60275052T
061C172S10152T
Description
CRT BOARD P784B3-1 PHILIPS ROHS
BRASS PIN
WAFER
WAFER& PLUG
LABEL
NT6812KG-20028
0.01UF 2KV 20% Z5U
10000PF -20%~ 18% 2KV
22PF -5% NPO 50V
1UF -20% 100V
47UF -20% 100V
47UF -20% 100V
FERRITE BEAD 10*6.0*0.8
CRT SOCKET(QQ FOCUS)
LM2476
CRT BOARD B784B3-1 PHILIPS
CFR 200OHM -5% 1/4W
CFR 33OHM -5% 1/4W
CFR 33OHM -5% 1/4W
CFR 33OHM -5% 1/4W
CFR 330K OHM -5% 1/4W
CFR 330K OHM -5% 1/4W
CFR 330K OHM -5% 1/4W
MFR 1.9KOHM - 1% 1/6W
MFR 33K OHM - 1% 1/6W
CFR 100 OHM -5% 1/6W
CFR 100 OHM -5% 1/6W
CFR 1K OHM -5% 1/6W
CFR 1K OHM -5% 1/6W
CFR 1K OHM -5% 1/6W
CFR 10K OHM -5% 1/6W
CFR 10K OHM -5% 1/6W
CFR 10K OHM -5% 1/6W
CFR 150 OHM -5% 1/6W
CFR 150 OHM -5% 1/6W
CFR 150 OHM -5% 1/6W
CFR 33 OHM -5% 1/6W
CFR 33 OHM -5% 1/6W
CFR 33 OHM -5% 1/6W
CFR 4.7K OHM -5% 1/6W
CFR 5.6KOHM -5% 1/6W
CFR 75 OHM -5% 1/6W
CFR 75 OHM -5% 1/6W
CFR 75 OHM -5% 1/6W
RES CF 5% 1/4W 1000HM A
45
Philips 12NC
9965 000 35739
9965 000 35873
9965 000 35874
9965 000 35875
9965 000 35538
9965 000 35876
9965 000 35487
9965 000 35488
9965 000 35574
9965 000 35540
9965 000 35541
9965 000 35541
9965 000 35542
9965 000 35877
9965 000 35543
9965 000 35878
9965 000 35879
9965 000 35545
9965 000 35545
9965 000 35545
9965 000 35546
9965 000 35546
9965 000 35546
9965 000 35547
9965 000 35548
9965 000 35549
9965 000 35549
9965 000 35550
9965 000 35550
9965 000 35550
9965 000 35551
9965 000 35551
9965 000 35551
9965 000 35880
9965 000 35880
9965 000 35880
9965 000 35552
9965 000 35552
9965 000 35552
9965 000 35554
9965 000 35555
9965 000 35556
9965 000 35556
9965 000 35556
9965 000 35557
17” CDT Color Monitor
L808
L807
R830
R817
R809
R804
FB804
R846
C842
C826
J816
FB805
FB806
J808
L804
L805
R841
R842
R843
D809
D803
D812
D813
D814
D811
D805
D810
D808
D807
D806
D804
D802
C815
C823
C824
C830
C841
C835
C836
C839
C802
C803
C809
C812
C843
C818
C817
C816
C833
061C172S10152T
061C172S10152T
061C172S47052T
061C172S47052T
061C172S47052T
061C175L10152T
061C175L56452T
061C175L82852T
065C44222013T
067C3054713T
071C559T
071C5523
071C5523
071C5523
071C5523
071C5523
073C5468810T
073C5468810T
073C5468810T
093C6021P52T
093C641152T
093C641152T
093C641152T
093C641152T
093C641152T
093C641152T
093C6450152T
093C6450152T
093C6450152T
093C6450152T
093C6450152T
093C6450152T
064C178J1040T
064C178J1040T
064C178J1040T
064C700J3330AT
065C1K2215T605
065C2K1015T692
065C2K1015T692
065C44210013T
065C44210113T
065C44210113T
065C44210113T
065C44210113T
065C44222013T
065C4441015T
065C4441015T
065C4441015T
065C4441525T
107B7
RES CF 5% 1/4W 1000HM A
RES CF 5% 1/4W 1000HM A
RES CF 5% 1/4W 47OHM AX
RES CF 5% 1/4W 47OHM AX
RES CF 5% 1/4W 47OHM AX
CFR 100 OHM -5% 1/2W
CFR 560K OHM -5% 1/2W
0.82 OHM -5% 1/2W
22PF -5% NPO 50V
470UF -20% 16V
CORE RF BEAD RH 3.5X6X0.76TP
FERRITE BEAD 7.5*3.5*0.8
FERRITE BEAD 7.5*3.5*0.8
FERRITE BEAD 7.5*3.5*0.8
FERRITE BEAD 7.5*3.5*0.8
FERRITE BEAD 7.5*3.5*0.8
0.68UH -10%
0.68UH -10%
0.68UH -10%
PS156R
1N4148
1N4148
1N4148
1N4148
1N4148
1N4148
BAV21
BAV21
BAV21
BAV21
BAV21
BAV21
CL21X0.1UF 63V -5%
CL21X0.1UF 63V -5%
CL21X0.1UF 63V -5%
0.033UF 63V -5%
220PF/1KV Y5P -10%
100PF/2KV
100PF/2KV
10PF -5% NPO 50V
100PF -5% NPO 50V
100PF -5% NPO 50V
100PF -5% NPO 50V
100PF -5% NPO 50V
22PF -5% NPO 50V
100 PF 10% 50V Y5P
100 PF 10% 50V Y5P
100 PF 10% 50V Y5P
1500PF 10% Y5P 50V
46
9965 000 35557
9965 000 35557
9965 000 35558
9965 000 35558
9965 000 35558
9965 000 35559
9965 000 35561
9965 000 35560
9965 000 35574
9965 000 35585
9965 000 35562
9965 000 35563
9965 000 35563
9965 000 35563
9965 000 35563
9965 000 35563
9965 000 35564
9965 000 35564
9965 000 35564
9965 000 35566
4822 130 30621
4822 130 30621
4822 130 30621
4822 130 30621
4822 130 30621
4822 130 30621
4822 130 30842
4822 130 30842
4822 130 30842
4822 130 30842
4822 130 30842
4822 130 30842
9965 000 35568
9965 000 35568
9965 000 35568
9965 000 35569
9965 000 35570
9965 000 35571
9965 000 35571
9965 000 35572
9965 000 35573
9965 000 35573
9965 000 35573
9965 000 35573
9965 000 35574
9965 000 35575
9965 000 35575
9965 000 35575
9965 000 35576
17” CDT Color Monitor
C837
C814
C804
C832
C831
C829
C827
C813
C834
C846
C847
C849
C801
C820
C821
C822
C810
C819
C807
C808
ZD804
065C44447113T
065C4501047T
065C4501047T
065C251K1042T
065C251K1042T
065C251K1042T
065C251K1042T
065C251K1042T
065C517K1025T6
065C517K1025T6
065C517K1025T6
065C517K1025T6
065C517K5612T6
067C701099T
067C701099T
067C701099T
067C3052203T
067C3054703T
067C3054703T
067C3054793T
093C3951952T
107B7
470PF -10% Z5P 50V
0.1UF 80-20% 50V Y5V
0.1UF 80-20% 50V Y5V
0.1UF 250V
0.1UF 250V
0.1UF 250V
0.1UF 250V
0.1UF 250V
1000PF 500V -10% Y5P
1000PF 500V -10% Y5P
1000PF 500V -10% Y5P
1000PF 500V -10% Y5P
560PF 500V Z5P -10%
1UF -20% 100V
1UF -20% 100V
1UF -20% 100V
22UF -20% 16V
47UF -20% 16V
47UF -20% 16V
4U7 16V
TZX8V2B
9965 000 35577
9965 000 35578
9965 000 35578
9965 000 35579
9965 000 35579
9965 000 35579
9965 000 35579
9965 000 35579
9965 000 35580
9965 000 35580
9965 000 35580
9965 000 35580
9965 000 35581
9965 000 35582
9965 000 35582
9965 000 35582
9965 000 35583
9965 000 35584
9965 000 35584
9965 000 35586
9965 000 35588
10. Different parts list
Diversity of 107B75/27 compared with 107B70/00
Location
Part No. for TPV
Description
034C6376BVBT
FRONT PANEL
034C6377VBT
BACK COVER
034C6378VBB
SWIVEL
034C6379VBB
BASE
040C58162410A
H/V LABEL
089C402A15NIS
POWER CORD
Q40C58162462A
CRT WARNING LABEL
Q40C70B8137A
RATING LABEL
089C71B5TYHG3
SIGNAL CABLE
47
Philips P/N (12NC)
9965 000 36568
9965 000 36569
9965 000 36570
9965 000 36571
9965 000 36572
9965 000 36575
9965 000 36573
9965 000 36574
9965 000 35436
17” CDT Color Monitor
107B7
11. Block diagram
SIGNAL
CABLE
R
G
B
H
FUNCTION
CONTROL
IC801
NT6812
PRE AMP
IC802
R
G
LM2476 O/P
B
EHT
CRT
24.5KV
FOCUS G2 HV G1
V
IC101
SAA4849
Q403,T402(FBT)
Q402,T401
HOR.O/P
HOR. DRIVER
Q907,Q908
X-RAY PROTECTION
Q909,Q910
POWER SAVING
Q406
IC601
TDA4863A
VERT.O/P
PINCUSHION &
H-SIZE CONTROL
BLANKING CIRCUIT
12.5V
DEGAUSSING
C.K.T
VIN
RECTIFIED
& MOOTHED
OUTPUTS
RECTIFIE
&SMOOTH
T901
POWER
6.3V
TRANSFORME
Q909
Q910
12V
Q907
Q908
6.3V
48V
R162
START C.K.T
R939,R940
D912
Q913
RY901
FROM
IC101
RECTIFIED
&SMOOTH
R155
LED
L906
VCC
POWER
SWITCH
IC901
CONTROL
PWM O/P
D
IC101
F.B
R930
Q911
POWER
MOSFET
R929
LINE
FILTER
FROM
H.O.T
AC INPUT
90V-264V
H-SYNC
C.K.T
29 31 13
S
B+ PWM
H-SYNC
CONTROL
48
IC101
OUTPUT
RECTIFIE
&SMOOTHED
(50V-165V
VARIABLE
B+
17” CDT Color Monitor
107B7
12.IC Block diagram
IC101
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
IC101 SAA4849
25
26
27
28
SwiChoice
NC
ISCL
DSDA
ISDA
DSCL
Mute G1
Vs
ROTA
Hs
H-LIN
EEP W/R
Unlock
Pro
CLAMP
VsOUT
CS1
REM
CS2
NC
CS3
XTAL2
standby
XTAL1
OFF
MODE
VSSE
VDDA
VDDD
Vssa
V5V
BOP
VSSD
Bin
BDRV
Bsens
HBGND
AGND
HDRV
Vref
HFB
Iref
XRAY
EWdrv
RST
VOUT2
Vfocus
VUOT1
Deguss
EHT
ABLadj
DouColor
KEY2
Uvolt
KEY1
SinColor
49
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
17” CDT Color Monitor
107B7
SAA4849
50
17” CDT Color Monitor
IC102
1
107B7
8
2
7
3
6
4
5
M24C08
2
VF
3
N
-I/P
GND
6
+I/P
+O/P
IC601
2
6
TDA4863AJ
3
FLYBACK
GENERATOR
5
1
POWER
AMPLITIER
7
5
+
THERMAL
PROTECTION
4
7
VCC
1
IC102 M24C08
4
51
17” CDT Color Monitor
107B7
IC801
NT6812
1
2
3
4
5
6
7
8
9
10
11
12
VBLK
HBLK
CAP_A
CLAMP
VDD_1
ABL
GND_A
R_OUT
R_IN
G_OUT
G_IN
B_OUT
B_IN
VDD_2
GND-PLL
GND_2
VCO
DA1
5V_PLL
DA2
SDA
DA3
SCL
CAP_D
52
24
23
22
21
20
19
18
17
16
15
14
13
17” CDT Color Monitor
107B7
IC802
LM2476
14
VCC
2
4
1
3
6
7
8
VBB
IND1
OUTD1
OUTD2
15
19
IND2
IND3
OUTD3
17
INC1
INC2 OUTC1
INC3 OUTC2
12
N/C
16
N/C
18
N/C
GNDS
10
5
GND
OUTC3
53
9
11
13
107B7
VCC
4
17” CDT Color Monitor
3
GND
D
S
OCP/FB
1
2
5
IC901
IC901
STR-G5643D
54
17” CDT Color Monitor
107B7
13. PCB Layout
13.1 Main Board
55
17” CDT Color Monitor
107B7
13.2 Video Board
56
17” CDT Color Monitor
107B7
14. Schematic diagram
HS
ZD103
6.2V
DSCL
ZD102
DSDA 6.2V
Sense
R156
3K3
R157
3K3
J061
NC
IC102
56C1133-13
1
8
A0
VCC 4.943V
R912
8.2 2W
2
Hfb
3
D914
Jumper
VO
4
HO
R167
100
A1
A2
C100
47UF
6
ISCL 4.412V
R105
100
R117
100
R152
5
A4 ISDA 4.286V
24LC08B
R103
100
R143
100
100
J085
NC
GND
R148
100
R149
100
H802
ZD106
NC
C103
0.1UF
C104
100UF/16V
R705
150 1/4W
47
R112
47
R106
C705
0.1UF
R107
4K7
15K
C145
R126
R116
3.9K
R104
100
R130
10K
R153
2.7K
R101
10K
100
R102
100
R125
470
XTAL2
12
4.909V standby
45
XTAL1 1.353V
13
4.910V OFF
MODE
5
4
R420
20
0.535V HDRV
21
0.793V HFB
26
0.23V ABLadj
27
4.801V KEY2
C106
1000 4.802V
28
KEY1
C105
1000
C120
0.1UF
38
AGND 2.519V
37
Vref 2.527V
36
34
VOUT2 0.925V
33
VUOT1 0.927V
32
EHT 2.57V
31
30
Uvolt 5.557V
470K 1/4W
C126
Jumper
C118
1UF 50V
ABLadj
10K
R416
180K 1/4W
C433
0.1UF 100V
D929
8.2K
C116
2N2
120K 1/4W
R970
VR902
200
C125
47UF NC
R150
56K
C115
0.47U
R134
D103
NC
R151
C114
2200
C109
2200
C124
2200
470
R135
C123
29
Led 0.276V 10000P
R115
470
470
R154 470
D104
1N4148
R137 75K
C108
2200 NC
C127
4700PF
R146
8K2
HFB
UF4004
+
R161
R138
75K
R147
62K
1/4W
5V
57
R418
11K 1/4W
+
R969
20K 1/2W
R144
R142
ZD105
24V
Page2:CPU Section
C434
4.7UF
40V
R133
3.9K
35
EWdrv 3.159V
NC
R131
2.2K
41 0.846V
C117
40 4700PF/100V
Bin 1.392V
2.173V
39
Bsens
Iref
25
0.4043V Deguss
240K 1/4W
VDDA
Xray
30K 1/4W
44
BOP
HBGND
12V
R417
16
4.94V V5V
VSSD
SW104
2.4K 1/6W
J066
X101
48MHz
93A 22 48-H
15
3.94V VDDD
17
5K6
SW105
46 1.355V
43 3.283V
+ C119
10UF 16V
42
Vssa 0.057V
VSSE
R193
R165
100
R961
8.2K 1/6W
VOUT2
DEG
R159
49
VsOUT 0.144V
100
R140
48
REM/P.S
120 1/6W
47
NC
EWDRV
VDF
SW103
R114
1.8K
5V
Xray
+
Pro
R113
1.8K
VOUT1
HFB
EEP W/R
EHT
HDRV
Hs
H-LIN
55 4.936V R110
C122 10
100
R111
54
4.94V
C121 10
100
53
0.042V
R132
100
52
0.35V
R172
100
51
4.93V R145
100
50
4.134V
50V
BDRV
Led
12V
Vs
ROTA
0.252V 23
RST
C102
0.1UF
24
3.043V Vfocus
+
R124
1K
22UF
3 5V
HFB
DSCL
CableSense
22
0.974V XRAY
R129
470
ABL
5K6
56
11
0.284V CS3
19
4.7K
2 Key1
6.3V
ISDA
18
0.705V BDRV
R123
1 Key2
5 gnd
DSDA
7
0.202V Unlock
14
R119
P102
ISCL
10
4.747V CS2
R108
SW106
NC
SwiChoice
9
4.747V CS1
80V
+
1
8
0.284V CLAMP
2K2
G1
C113
100UF 16V
R139
1K
2
C107 4.388V
100
3
+
C110 4.253V
100
4
0.046V
R122
5
100 2.282V
R118
6
4.42V
100
2K2
G1
R192
2K4
2K4
IC101
SAA4849PS
+
R109
80V
R191
R194
JUMP
7
WP 4.93V
ABL
CONN
3
J081
R120 100
6.3V
4
2
1
CS3
ROTA
H-LIN
CS2
20K
C101
0.1UF
12V
HFB
LED1
SW102
J062
JUMP
+
ISDA
Keyboard:715C1614-*
Key2
R158
ZD901
ISCL 5.1V
R911
100 2W
Led
2pin
5V
GND
5V
R121
Jumper
ZD108
TZX5V6D
H803
CON
gnd Key1
C130
1000PF
ZD101
6.2V
GND
H104
C131
33PF
ZD104
6.2V
VS
Unlock
1N5817
CS1
OFF
5V
D101
5V
Standby
CPU
CMPCB:715C1515-*-S4
1K 1/4W
50V
17” CDT Color Monitor
107B7
R405
1.8K 1/4W
T401
79C167-125-LS
1
6
5
3
4
Q402
57C530-503-T
2SD1207T
HDRV
C940
4.7U 16V
Q401
PH2369
+
Q403
57C706-505
2SC5929
C410
0.1UF
R428
0.75 3W
R410
10 1/2W
C417
0.22UF 100V
D406
R425
100 1/4W
R429
10 1/2W
5.1V
ZD401 NC
56V
R433
EWDRV
ZD402 NC
C418
4700P/1.6KV
470
8
4
C480
FR157S
D404
UF4004
6
+
80V
EHT
R740
56K 1/2W
C401
1000UF/25V
1K 1/2W
C713
2.2uF/250V
C402
47UF/160V
D410
1N4148
14
JUMPER
R721
4.7K
R463
2M 1/4W
C422
2.2uF/100V
ZD701
5.1V
93C 39-516-52T
4
2
C407
NC
12.8V
R443
1K
R460
D463
4K7 1/4W
FR107
Q411
2PC945
57C 419-PP-T
R484
R486
D474
4K7 1/4W
FR107
Q423
2PC945
57C 419-PP-T
C411
0.1UF
3
4
R471
100K 1/4W
R413
10 1/4W
1
5
C488
56PF/2KV
C489
Jupmer
C720
1000PF/500V
C425
Q420
IRF630M
57C600-21
R419
100K 1/4W
0.27uF/250V
ZD702
TZX3VC
R478
220K 1/4W
4K7 1/4W
FR107
R422
10 1/4W
C431
0.1
R472
100K 1/4W
Q427
IRF630M
57C600-21
0.68uF/250V
Page3:Output Section
Power
58
ZD711
5.1V
R720
4.7K
1/4W
ZD703
93C39-502-52T
18V
R477
220K 1/4W
40V
Q412
2PC945
57C 419-PP-T
D464
R715
36K 1/6W
R713
3K3
R707
5K6 1/4W
HFB
R445
R461
R716
160K 1/6W
Q705
57C 498-3-T
BF423
0.27uF/400V
C427
R448
10k 1/4W
1K
C429
0.1
+
C712
10UF NC
T403
79C167-124-H
6
0.1uF/250V
R476
220K 1/4W
C423
R487
10K 1/4W
1k
Q426
R421
IRF630M
10 1/4W 57C600-21
R456
560 3W
R407
22 2W
C426
R444
10K 1/4W
Q743
2SC1213
57C446-500-T
C430
470P 500V
C715
NC
R415
1K
Unlock
5
R446
Jumper
3
Q410
2SC2120Y
R725
180K 1/2W
L401
73C147-539-H
G1
R449
6K2 1/4W
R447
1.2K
CS3
C710
0.012UF 100V
R702
620 1/2W
H-LIN
CS2
D706
5
10
C450
6.3V
CS1
VDF
R723
R724
10 2W
9
47P 2KV
73C253-69-T 150uH
Q406
IRF630M
57C600-21
E.H.T
F1
F2
G2
7
FB403
71C55-9-T
C419
4700PF/630V
L405
R412
47K 1/4W
T402
79A774-504-EG
EHT
F1
F2
2
G2
13
3
12
11
1
FB402
71C55-9-T
93C60-21P52T
D408
PS156R DMV1500M
93C220-512
D407
PS156R
R403
68K 1/4W
H-DY
4
R607
1 1W
NR601
45
D405
1N5817
C415
4700 100V
C413
D450
0.1U 63V 1N4148
3
ABL
R984
2K7
V-DY
2
ABLadj
R605
1.5 1/2W
C603
1000uF/16V
C414
0.47UF 63V
1
80V
+
33 3W
D403
UF4004
C742
10UF 16V
P402
-12.5V
R426
68K 1/4W
C432
1000PF/1KV
4
R604
1.8K
12.8V
R748
6.8K
R749
R606
120
1W
C608
0.1UF/100V
-11.92V
12V
B+
+
-I/P
FB404
470 1/4W J038
Jumper
R751
2.4K
5
+O/P
0.616V
6
C741
NC
71C55-29
C601
1000PF 63V
R602
1.8K
GND
R610
130
R603
VOUT2
2
7
+I/P
0.63V
470 1/4W
R741
430K 1/2W
+
R601
VOUT1
C740
0.01uF/500V
Q742
57C 493-12A-T
BF420
R608
270
1/2W
VF
IC601
56C584-1A
TDA4863A
3
C605
1000UF/16V
N
+
1
VCC 12.07V
4.7 1/2W
+
12.8V
226.3V
D740
UF4004
+
D601
1N4004 C609
93C52-47T-52T 47UF/50V
R750
-12.5V
Output
!
!
NR901
NTCR
61C 58-8T-L t
C956
0.1UF
R983
10K
4
2
!
VCC
100 1/2W 1N4148
Q913
2PC945
R982
10K
J079
C921 JUMPER
0.1UF/100V
R917
68K 1/4W
3
GND
32.2V
!
SW901 NC
off 77A411A-2-CJ
1
-
2
3
C963
3300PF/250V
C962
3300PF/250V
D
S
FB901
71C55-19-T
D911
UF4004
+
FB907
93C3040-8AT
RG4S
2
+
12
!
R930
5
1.093V
C920
470PF/50V
680 1/4W
R929
0.20 2W
C961
3300PF/250V
R958
1K 1/4W
D923
9
93C3020-8AT
RG4ZS
6.61V
+
Q910
2PC945
R918
R941
1N4148
SYNC+
12.8V
R959
10K
510 1/4W
10K
R905
6K2
SYNC-
+
C937
1000UF/16V
OFF
R908
7.5 1/2W
R907
680 1W
R909
R902
FROM
FBT
BDRV
Q901
PH2369
+
R933
10K
C939
1000uF/16V
R980
1K 1/4W
220 1/4W
Q912
2SA733P
Q909
2SB772P
57C2015-1A
1
Q902
2SC2120Y
C912
2.2UF/50V
R903
43 1/4W
!
Q903
2PC945
C908
0.1UF
Q905
2SA733P
R906
47 1/4W
IC902
L7805CV
I
O
I
O
!
6.3V
C483
4.7UF/16V
R965
4.7 1/4W
10K
G
L902
73A 174-502-HB
+
R952
G
3
R910
91K
Q907
57C2015-1A
2SB772P
D913
Jumper
C901 !
NC
2
R957
47K
C936
1000uF/25V
71C55-503
R901
1M 1/2W
R951
470 1/4W
D926
Jumper
4
1
13V
71C55-9-T
12V
JUMPER
Q906
2PC945
D922
11
C910
22UF/50V
R919
R963
0.22 2W
R960
22K 1/4W
R401
100K 1/2W
C482
0.68UF 250V
4
1
OCP/FB
R962
47 1/4W
10
FB902
2
Q911
STP8NS25-E
57C600-512
7
B+
D925
93C1040-2-52T
UF4004
R915
100K 1/4W
C918
150PF/2KV
3
93C60-26W-52T
FR107
C931
0.uF 250V
100 1/4W
L901
73A 174-7-S3G
!
D910
D912
BAV20
+
8
R916
1.3K 3W
L906
73C253-109-SP
48V
31DF4
R927
33K 1W
on
D916
3
2
C900
1uF/275V
C919
0.01UF/2KV
1
IC901
56C379-504
STR-G5643D
!
ZD903
20V
D919
5
C922
100/2KV
!
!
T901
80AS774-2-N1G
R939
390K 1W
!
+
1
CN902
!
!
RY901
77C260-5-4
t
4
3
6
5
1
2
D939
R981
C907
220uF/400V
R940
430K 2W
D901~D904
93C52-9T-52T
2A05
4
!
PR901
61C52-27-4W
9 OHM PTCR
+
C916
470P/1KV
C917
150PF/2KV
!
C964
3300PF/250V
13V
5V
DEG
291V
50V
107B7
ROT
17” CDT Color Monitor
F901
4A/250V
84A7H-400-SL
Q908
2PC945
!
R953
R921
10K
Stand by
10K
CN901
N
G
1
0
0
36KHZ~40KHZ
0
1
0
40KHZ~44KHZ
0
0
1
44KHZ~50KHZ
5V
33KHZ~36KHZ
1
1
0
50KHZ~62KHZ
0
1
1
>62KHZ
1
1
1
Page1:Power Section
LED1为单色发光二极管,POWERSAVING时为绿闪;LED2为双色发光二极管;
59
Based on the Bom of Sep-19-05
3
2
1
L
注:电压测试条件:输入:220V/50HZ,H-FREQ:68KHZ,V-FREQ:85HZ;万用表直流档
CS TABLE:
Frequency
CS1
CS2
CS3
<33KHZ
0
0
0
CN903
17” CDT Color Monitor
107B7
Video
CRPCB:715C1451-*
3.3K
1
2
3
R/I FB80153A40-8
R836
R834
75
GND
3
G/I FB802 53A40-8
4
GND
33
D803
4148
R818
33
R824
75
5
B/IFB803 53A40-8
6
GND
C807
47UF/16V
+
4148
C815
D805
4148
C824
D812
4148
33
R807
0.1UF
C823
0.1UF
5
JUMP
0.1UF
6
R806
JUMP
7
R827
JUMP
D811
4148
C830
0.033uF
R811
5.6K
J816
71C55-9-T
8
C833
1500
12
11
10
9
8
7
6
5
4
3
2
1
CON14
12
100
C802
100P
13
11
100
R805
C803
100P
9
R810
33K 10
R802
14
3
4
CONN
P802
2
R825
10K
D813
R821
R826
75
C837
470P
C812
100P
D814
4148
R833
5V
+
ISCL
C828
47UF,16V
JUMPER
VBLK
HBLK
CAP_A
CLAMP
VDD_1
ABL
GND_A
R_OUT
R_IN
G_OUT
G_IN
B_OUT
B_IN
VDD_2
GND-PLL
GND_2
VCO
DA1
5V_PLL
DA2
SDA
DA3
SCL
CAP_D
R831
+
C839
10PF
23
R832
21
C808 +
4.7UF/16V
100
R835
20
C842
10PF
HZ9A3-E
100
100
18
2
1
16
15
C844
10PF
5
R816
6
1K
R813
C816
100P
1K
C817
100P R812
13
C810
22UF/16V
0.1UF/150V
C832 4
C843
10PF 3
17
14
+
IC802
56C551-525
LM2476
VCC
+
ZD804
7
8
1K
C818
100P
10
FB805
JUMP
C826
470UF,16V
1UF/100V
C831
0.1UF 250 14
C848
+
47UF/16V
C819
R820
19
VBB
OUTD1
IND1 OUTD2
IND2
GND
GND
INC1 OUTC1
INC2 OUTC2
INC3 OUTC3
GND
GND
C804
0.1UF
FB806
R815
150 1/4W
150 1/4W
R842
0.68UH
19
L808
C822
1UF/100V
71C55-23
C811
47UF/100V
L804
71C55-23
18
47
R841
R814
CLP
+
10K
HT
C805
47UF/100V
JUMPER
G1
80V
G
11
B
C829
0.1UF/250V
C846
1000P/500V
16
9
L809
11
D806
BAV21
C821
100 1/4W 1UF/100V
R844
330K 1/4W
R828
33 1/2W
D808
BAV21
J811
13
71C55-503
12
C814
0.1UF/50V
R830
47
C813
C847
0.1UF/250V 1000P/500V
C834
1000P/500V
Page4:Video Section
C836
100P/2KV
C841
220PF/1KV
1000P/500V
C849
C806
103 2KV
J809
C827 71C55-503
0.1UF/250V
L807
FB804
560K 1/2W
D810
BAV21
C820
1UF/100V
D802 BAV21
R837
330K 1/4W
R829
33 1/4W
R846
0.82 1/2W
C801
560PF 500V
R804
100 1/2W
FB809
71C55-21
C835
100P/2KV
G2
FOCUS
L805
71C55-9-T
C825
NC
71C55-503
D809
PS156R
D801
ABL
R
6
0.68UH
100 1/4W
VF
8
33 1/2W
D807
BAV21
J810
R817
R809
47
J808
+
R840
R843
0.68UH
17
CPT 17` LowPower CRT
750A5X305AV
CRT
100 1/4W
+
HF
GND
GND
IND3 OUTD3
15
!
R819
330K 1/4W
D804
BAV21
71C55-23
ISDA
X
R822
4K7
22
GND
12V
C838
NC
24
5
1
7
R845
P801
R806
1.9K
IC801
NT6812KG-20019
56A366-521
9
C809
100P
Attention:Based on the Bom of Sep-19-05
60
17” CDT Color Monitor
107B7
15. General Product Specification
Table of Contents
1.
1.1
1.2
2.
2.1
2.2
2.2.1
2.2.2
2.3
2.4
2.5
2.5.1
2.5.2
2.6
2.6.1
2.6.2
2.6.3
2.6.4
2.7
2.7.1
2.7.2
2.7.3
2.7.4
2.7.5
2.7.6
3.
3.1
3.2
3.3
4.0
4.1
4.2
4.3
5.0
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
5.10
5.11
5.12
5.13
5.14
5.15
5.16
6.0
6.1
6.2
6.3
Scope
General product feature
Product range
Electrical Performance
Standard testing conditions
Video signals
Video input signals
Video driver signals
DDC signals
Plug and Play
Preset modes timing chart
Preset video timings
Preload video timings
Power supply
Features
Power consumption
Power saving conditions
Power recovery from power saving
User controls / Indicators / Connectors
Front controls
OSD menu
LED indicator
Monitor status information
Power connector
Video input connector / Video cable
Front Of Screen Performance
CRT characteristics
Display image / Geometric distortions
Optical performance
Accessories
Cables
User’s manual
CD-ROM
Mechanical
Cosmetic
Mechanical data files
Location of Philips logo
Location of icons
Color for resin / Paint
Resins
If paint is used
Plastic mold tooling
Plastics flammability
Texture / Glossing of housing
Tilt / Swivel base range
Movement of unit with base
Label
Product dimension / Weight
Transportation
Pallet / Container loading
Reliability/Environment/Transportation
MTBF prediction
Demonstration MTBF
Temperature
61
17” CDT Color Monitor
6.4
6.5
6.6
6.7
7.0
7.1
7.2
7.3
7.4
7.5
7.6
107B7
Humidity
Altitude
Air pressure
Earth magnetic field
Regulatory compliance
World regulatory
EMC requirements
MPR II / TCO
RoHS
WEEE
Ongoing regulatory
1. Scope
This specification describes features and performance of 107B7 CRT monitor.
•
Product Name -
PH107B7
•
Manufacturer ID -
PHL
•
Product ID -
001D
1.1 General Product Features
•
17” Flat screen color monitor
•
0.25mm phosphor dot pitch
•
Viewable Image Size 325mm x 244mm
•
Universal power supply
•
DPM compliant
•
8 preset modes, 6 user modes, GTF supported
•
Horizontal frequency up to 86 kHz
•
Vertical refresh rate up to 160 Hz
•
Maximum display resolution up to 1600x1200
•
VESA DDC 2B compliant
•
Plug and Play
•
Picture High Brightness selection
•
Multi-language OSD user control
•
Tilt and swivel adjustable base
•
TCO03
62
17” CDT Color Monitor
107B7
1.2 Product Range
CTV
Destination
107B70/00
107B70/27
107B75/27
Europe
NAFTA
NAFTA
Mains
Cord
European
US
US
Magnetic
Field
North
North
North
Cabinet
Color
Grey
Grey
Black
Ergonomics
TCO'03
TCO'03
TCO'03
OSD
Language
9
9
9
2. Electrical Performance
All performance specifications are defined under “STANDARD TESTING CONDITIONS”, unless otherwise
specified.
2.1 Standard Testing Conditions
•
Monitor facing to the east
•
Warm up time -
≥ 30 min
•
Ambient temperature -
25 ± 3 °C
•
Prime mode -
•
Color temperature -
9300 °K
•
Video signal level -
700mVpp
•
Brightness setting -
50% (set to near cutoff)
1024x768@85Hz
2.2 Video Signals
2.2.1 Video Input Signals
•
Maximum pixel rate -
•
Sync input -
TTL level, separate H/V sync only, “+” or “-“ polarity,
terminated with ≥ 2.2kΩ impedance.
•
Horizontal frequency -
30 ~ 86 kHz.
•
Horizontal sync width -
0.6 us minimum, 4 us maximum.
•
Vertical frequency -
50 ~ 160 Hz.
•
Vertical sync width -
2 lines minimum, 10 lines maximum.
•
Analog RGB level -
•
Preset video modes -
180 MHz.
0 ~ 700mV linear, positive polarity, terminated with 75Ω ± 5%
impedance.
8 preset modes. All visual performance has to fulfill the FOS
performance specifications. The user can recall the factory setting
in OSD menu.
63
17” CDT Color Monitor
107B7
•
Preload video modes -
•
User modes -
•
Detectable mode frequency separation -
15 preload modes. Parameters preloaded in EEPROM, little size
and centering deviations are allowed, but geometry distortions
should be strictly managed for users easy adjustment. The user can
recall the factory setting in OSD menu.
6 user modes. User can store adjustment result of 6 new modes,
first in first out control when over 6 new modes are encountered.
± 1kHz min. for H-sync, ± 1Hz min. for V-sync.
2.2.2 Video Driver Signals
•
Rise time -
< 8.5ns / 30Vpp (real measurement, white to black)
•
Fall time -
< 8.5ns / 30Vpp (real measurement, black to white)
•
Overshoot / undershoot -
< 15%
•
Black level shift -
< 5% (30 min ~ 3 hour)
2.3 DDC Signals
•
Support VESA DDC/2B according to VESA DDC standard Ver.1.0 Rev. 3.
•
DDC1 is not allowed.
The DDC components are connected to both monitor Vcc and DDC +5V (from PC via video cable), that the PC can
read the DDC data also when the monitor is powered off. To prevent current feedback into PC, blocking diodes are
required at monitor side.
•
•
DDC serial Data DDC serial Clock -
2
D-sub connector pin 12, I C-BUS.
D-sub connector pin 15, I2C-BUS.
2.4 Plug And Play
Win Logo certification required.
•
Win logo test logs to be provided by suppliers during DVT stage.
2.5 Preset & Preload Modes Timing Chart
2.5.1 Preset video timings
64
17” CDT Color Monitor
107B7
Timing
Resolution
Pixel clock
H. Frequency
H. Total
H. Active display
H. Back porch
H. Sync. Width
V. Frequency
V. Total display
V. Active display
V. Back porch
V. Sync. Width
H/V sync
polarity
1.
640 x 480
25.175 MHz
31.469 kHz
31.778 us
25.422 us
1.907 us
3.813 us
59.941 Hz
16.683 ms
15.253 ms
1.049 ms
0.064 ms
-/-
2.
640 x 480
36.000 MHz
43.269 kHz
23.111 us
17.778 us
2.222 us
1.556 us
85.008 Hz
11.763 ms
11.093 ms
0.578 ms
0.069 ms
-/-
3.
720 x 400
28.321 MHz
31.468 kHz
31.778 us
25.422 us
1.907 us
3.813 us
70.084 Hz
14.268 ms
12.711 ms
1.112 ms
0.064 ms
-/+
Timing
Resolution
Pixel clock
H. Frequency
H. Total
H. Active display
H. Back porch
H. Sync. Width
V. Frequency
V. Total display
V. Active display
V. Back porch
V. Sync. Width
H/V sync
polarity
4.
800 x 600
49.500 MHz
46.875 kHz
21.333 us
16.162 us
3.232 us
1.616 us
75.000 Hz
13.333 ms
12.800 ms
0.448 ms
0.064 ms
+/+
5.
800 x 600
56.250 MHz
53.674 kHz
18.631 us
14.222 us
2.702 us
1.138 us
85.061 Hz
11.756 ms
11.179 ms
0.503 ms
0.056 ms
+/+
6.
1024 x 768
78.750 MHz
60.023 kHz
16.660 us
13.003 us
2.235 us
1.219 us
75.029 Hz
13.328 ms
12.795 ms
0.466 ms
0.050 ms
+/+
Timing
Resolution
Pixel clock
H. Frequency
H. Total
H. Active display
H. Back porch
H. Sync. Width
V. Frequency
V. Total display
V. Active display
V. Back porch
V. Sync. Width
H/V sync
polarity
7.
1024 x 768
94.500 MHz
68.677 kHz
14.561 us
10.836 us
2.201 us
1.016 us
84.997 Hz
11.765 ms
11.183 ms
0.524 ms
0.044 ms
+/+
8.
1280 x 1024
135.000 MHz
79.976 kHz
12.504 us
9.487 us
1.837 us
1.067 us
75.024 Hz
13.329 ms
12.804 ms
0.475 ms
0.038 ms
+/+
2.5.2 Preload video timings
65
17” CDT Color Monitor
107B7
Timing
Resolution
Pixel clock
H. Frequency
H. Total
H. Active display
H. Back porch
H. Sync. Width
V. Frequency
V. Total display
V. Active display
V. Back porch
V. Sync. Width
H/V sync
polarity
1.
640 x 350
25.175 MHz
31.469 kHz
31.778 us
25.422 us
1.907 us
3.813 us
70.087 Hz
14.268 ms
11.122 ms
1.907 ms
0.064 ms
+/-
2.
640 x 480
31.500 MHz
37.500 kHz
26.667 us
20.317 us
3.810 us
2.032 us
75.000 Hz
13.333 ms
12.800 ms
0.427 ms
0.080 ms
-/-
3.
640 x 480
40.500 MHz
50.628 kHz
19.752 us
15.802 us
1.975 us
1.580 us
100.10 Hz
9.995 ms
9.481 ms
0.435 ms
0.059 ms
-/-
Timing
Resolution
Pixel clock
H. Frequency
H. Total
H. Active display
H. Back porch
H. Sync. Width
V. Frequency
V. Total display
V. Active display
V. Back porch
V. Sync. Width
H/V sync
polarity
4.
800 x 600
40.000 MHz
37.879 kHz
26.400 us
20.000 us
2.200 us
3.200 us
60.317 Hz
16.579 ms
15.840 ms
0.607 ms
0.106 ms
+/+
5.
800 x 600
50.000 MHz
48.077 kHz
20.800 us
16.000 us
1.280 us
2.400 us
72.188 Hz
13.853ms
12.480 ms
0.478 ms
0.125 ms
+/+
6.
800 x 600
67.500 MHz
63.923 kHz
15.644 us
11.852 us
2.370 us
0.948 us
100.00 Hz
9.997ms
9.387 ms
0.548 ms
0.047 ms
+/+
Timing
Resolution
Pixel clock
H. Frequency
H. Total
H. Active display
H. Back porch
H. Sync. Width
V. Frequency
V. Total display
V. Active display
V. Back porch
V. Sync. Width
H/V sync
polarity
7.
832 x 624
57.280 MHz
49.722 kHz
20.110 us
14.520 us
3.910 us
1.117 us
74.546 Hz
13.410 ms
12.550 ms
0.784 ms
0.060 ms
+/+
8.
1024 x 768
65.000 MHz
48.363 kHz
20.677 us
15.754 us
2.462 us
2.092 us
60.004 Hz
16.666 ms
15.880 ms
0.600 ms
0.124 ms
-/-
9.
1024 x 768
75.000 MHz
56.476 kHz
17.707 us
13.653 us
1.920 us
1.813 us
70.069 Hz
14.272 ms
13.599 ms
0.513 ms
0.106 ms
-/-
66
17” CDT Color Monitor
107B7
Timing
Resolution
Pixel clock
H. Frequency
H. Total
H. Active display
H. Back porch
H. Sync. Width
V. Frequency
V. Total display
V. Active display
V. Back porch
V. Sync. Width
H/V sync
polarity
10.
1152 x 864
108.000 MHz
67.500 kHz
14.815 us
10.667 us
2.370 us
1.185 us
74.979 Hz
13.333 ms
12.678 ms
0.568 ms
0.044 ms
-/-
11.
1280 x 960
108.000 MHz
60.000 kHz
16.667 us
11.852 us
2.889 us
1.037 us
60.000 Hz
16.667 ms
16.000 ms
0.600 ms
0.050 ms
+/+
12.
1280 x 960
148.500 MHz
85.938 kHz
11.636 us
8.620 us
1.508 us
1.077 us
85.000 Hz
11.764 ms
11.171 ms
0.547 ms
0.035 ms
+/+
Timing
Resolution
Pixel clock
H. Frequency
H. Total
H. Active display
H. Back porch
H. Sync. Width
V. Frequency
V. Total display
V. Active display
V. Back porch
V. Sync. Width
H/V sync
polarity
13.
1280 x1024
108.000 MHz
63.981 kHz
15.630 us
11.852 us
2.296 us
1.037 us
60.020 Hz
16.661 ms
16.005 ms
0.594 ms
0.047 ms
+/+
14.
1600 x 1200
162.000 MHz
75.000 kHz
13.333 us
9.877 us
1.877 us
1.185 us
60.000 Hz
16.667 ms
16.000 ms
0.613 ms
0.040 ms
+/+
15.
1600 x 1200
175.500 MHz
81.250 kHz
12.308 us
9.117 us
1.732 us
1.094 us
65.000 Hz
15.385 ms
14.769 ms
0.566 ms
0.037 ms
+/+
2.6 Power Supply
2.6.1 Features
•
AC line voltage range -
90Vac ~ 264Vac.
•
AC line frequency range -
50/60 Hz ± 3 Hz.
•
Input voltage transient -
300Vac for 10 seconds (China), 280Vac for 10 seconds (RoW).
•
Inrush current -
< 50 A at 240Vac cold start.
•
Earth leakage current -
< 1.0mA at 240Vac.
•
Power factor correction -
According to EN61000-3-2
2.6.2 Power consumption
It is equipped with two-stage power saving management. A delay of 5 seconds before entering the power saving
state is required to avoid misunderstanding of display resolution and timing mode changes.
67
17” CDT Color Monitor
107B7
•
Power on -
•
Active off -
< 2w at 120Vac / 240Vac.
•
Switch off -
< 2w at 120Vac / 240Vac.
< 75w. (Test requirements refer to EN61000-3-2)
2.6.3 Power saving conditions
The monitor enters DPM off mode when no H&V sync or one of H-sync / V-sync input is absent. No message
appears before entering DPM mode.
2.6.4 Power recovery from power saving
Both H-sync and V-sync are detected.
2.7 User Controls / Indicators / Connectors
2.7.1 Front controls
•
OSD menu is accessed by the keypad.
Key (R to L)
Power
Function
Tact DC switch
Menu
OSD Menu
“+”
Brightness/Adjust increase/Menu selection
“-”
Contrast/Adjust decrease/Menu selection
High Brightness
HB 4 levels hot key selection
•
Access main menu by pressing “MENU” key.
•
Select function via “+/-” & “MENU” keys, increase/decrease via “+/-” keys.
•
Brightness control -
Direct access only by hotkey.
•
Contrast control -
Direct access only by hotkey.
68
17” CDT Color Monitor
•
High Brightness -
107B7
By hotkey only, 4 levels.
1. Text
2. Internet
3. Game
4. Multimedia
2.7.2 OSD menu
•
Languages (per region) 9 languages (English, French, German, Italian, Spanish,
Portuguese, Korean, Turkish, Russian).
•
OSD tree -
OSD tree / English
1st level
LANGUAGE (per region)
ZOOM
ADJUST HORIZONTAL
ADJUST VERTICAL
ADJUST SHAPE
As shown below.
2nd level
8 LANGUAGES
9 LANGUAGES
POSITION
SIZE
POSITION
SIZE
ADJUST SIDE CURVE
ADJUST SIDE ANGLES
ADJUST COLOR
RESET TO FACTORY
SETTING
EXTRA CONTROLS
ROTATE IMAGE
9300K FOR GENERAL USE
6500K FOR IMAGE MANAGEMENT
5500K FOR PHOTO RETOUCH
sRGB
USER PRESET
RED
GREEN
BLUE
NO
YES
ADJUST MOIRE
3rd level
PINCUSHION
BALANCED
TRAPEZOID
PARALLELOGRAM
ROTATE
HORIZONTAL
VERTICAL
DEGAUSS
CLOSE MAIN CONTROLS
•
OSD lock -
Lock all OSD by holding down “MENU” key for 15 seconds.
2.7.3 LED indicator
•
Normal on -
•
Active off -
•
Switch off -
Green.
Green Blinking (1sec on / 1sec off).
Blank.
69
17” CDT Color Monitor
107B7
2.7.4 Monitor status information
•
Self-test feature -
“CHECK SIGNAL CABLE” message appears when video cable
is disconnected.
•
Out of scan range -
“FREQUENCY IS OUT OF RANGE” appears when input H-sync
or V-sync out of range.
•
Resolution & H/V input -
Shown in OSD menu “EXTRA CONTROLS”.
2.7.5 Power connector
•
AC socket 3-pin IEC-320-C13, at rear side.
2.7.6 Video input connector/Video cable
•
1.5m non-detachable fly-in video cable with D-Sub 15 pin male blue connector, pin assignment of D-Sub:
Function
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Red video
Green video
Blue video
GND
Self test
Red GND
Green GND
Blue GND
+5V (Supply from PC for DDC circuit)
Sync GND
GND
DDC serial data
H-sync
V-sync
DDC serial clock
•
H-sync line impedance must be within 50 ~ 70Ω (TDR measurement).
•
V-sync line impedance should be within 40 ~ 70Ω (TDR measurement).
•
RGB signal lines must be 75Ω ± 5% coaxial.
•
R, G, B coaxial shield must connect to D-Sub metal shell.
3. Front Of Screen Performance
3.1 CRT characteristics
70
17” CDT Color Monitor
107B7
Vendor
LPD
CRT Type Number
Screen & Mask
Screen Diagonal Size
Phosphor Area
VIS (front bezel opening)
Neck size
Deflection Angle
Yoke impedance
Phosphor Dot Pitch
Phosphor Type
Light Transmission rate
Surface Treatment
Surface Resistance
CRT net Weight
CPT
Flat screen & Shadow mask
444mm
325mm x 244mm
Flat screen & Shadow mask
444mmm
325mm x 244mm
29.1mm
90º
LH: xxx uH
LV: xxx mH
RH: xxx Ω
RV: xxx Ω
0.25mm
P22, medium short persistence
29.1mm
90º
LH: xxx uH
LV: xxx mH
RH: xxx Ω
RV: xxx Ω
0.25mm
P22, medium short persistence
Anti glare/Anti static
Anti glare/Anti static
3.2 Display image / Geometric distortions
•
Nominal display size 306mm x 230mm ± 4mm for all preset modes.
306mm x 230mm ± 12mm for preload modes.
•
Size control range -
Nominal total size: -15mm to full scan.
•
Raster centering -
< 4mm for prime mode.
•
Image centering -
< 5mm for all preset modes.
< 12mm for preload modes.
•
Position control range -
H: ± 10mm minimum, V: ± 8mm minimum.
•
Line straightness -
•
Image tilt -
< 1.0mm (each side).
•
Dynamic EHT size regulation -
< 1.0mm (each side).
•
Static EHT size regulation -
< 1.5mm (each side).
•
Image size stability -
< 1.0% (110Vac ~ 240Vac) as a function of supply voltage.
< 1.0% (5 ~ 40ºC) as a function of temperature.
•
Linearity [(max–min)/mean] -
Pattern: 12 x 9 blocks.
Prime modes: 1024x768@85, 1280x1024@75.
Border overall distortion < 2.0mm for all preset modes, the
waviness of any vertical or horizontal should be less than 1.0mm
over a 50mm distance.
Overall H&V < 10% (prime modes).
Adjacent H&V < 6% (prime modes).
Overall H&V < 14% (other modes).
Adjacent H&V < 7% (other modes).
•
Convergence -
Zone A < 0.25mm, Zone B < 0.35mm.
Zone B < 0.4mm (for modes < 50kHz).
71
17” CDT Color Monitor
•
107B7
Jitter 0.1mm. (No annoying level by visual)
<
3.3 Optical performance
•
Focus -
“me” pattern characters must be clearly identified at prime mode,
brightness 50%, set contrast for 25Fl at full white.
•
Full white luminance -
29 ± 4 fl (brightness: 50%, contrast: maximum).
•
5x5cm block luminance -
40 ± 5 fl (brightness: 50%, contrast: maximum).
•
Raster light output (w/o video signal, brightness at 50%, contrast at 0%) < 0.3 fl (raster has to disappear when brightness set to 0%).
•
Raster light output (w/o video signal, brightness at 100%, contrast at 0%) > 0.3 fl.
•
High Brightness (5x5cm white block, brightness at 50%, contrast at maximum)(check at 9300K only)
Text: 40 ± 5 fl
Internet: 60 ± 8 fl
Game: 80 ± 8 fl
Multimedia: 100 ± 10 fl
•
Brightness uniformity -
•
Preset 9300K colour -
x = 0.283 ± 0.015
y = 0.297 ± 0.015
•
Preset 6500K colour -
x = 0.313 ± 0.015
y = 0.329 ± 0.015
•
Preset 5500K colour -
x = 0.332 ± 0.015
y = 0.347 ± 0.015
•
Preset sRGB colour -
x = 0.313 ± 0.015, (brightness set at 23 ± 3 fl)
y = 0.329 ± 0.015.
•
White colour uniformity -
<0.015 (contrast at maximum for center to corner).
•
Colour tracking -
<0.020 (set contrast from 10fl to maximum).
> 75% (9 block measurements for center to corner).
72
17” CDT Color Monitor
107B7
•
Moire -
The clouding effect must not rise to disturbing levels in anywhere
of the screen with luminance setting from 15 to contrast 100%.
•
Video blanking -
During mode change or unstable input signal, the video will be
blanking for 1s to 2s, no switching behaviour is visible.
•
Local doming -
•
Proximity -
Not allowed.
No on-screen interference can be seen, when two monitors are
placed side by side (distance: 30cm) and operate in different
modes.
4. Accessories
4.1 Cables
•
Power cord (option) -
Length: 1.5 M +/- 50 mm
4.2 User’s manual
•
8 languages Quick Setup Guide.
4.3 CD-ROM
•
User’s manual, driver,……………..
5. Mechanical
5.1 Cosmetic
Philips ID
5.2 Mechanical data files
ProE files required
5.3 Location of logo
Per Philips make-up sheet
5.4 Location of icons
Per Philips make-up sheet
73
17” CDT Color Monitor
107B7
5.5 Color for resin/paint
Per Philips make-up sheet
5.6 Resins
•
RoHS requirements.
•
WEEE requirements.
5.7 If paint is used
•
RoHS requirements.
•
WEEE requirements.
5.8 Plastic mold tooling
•
Tooling to be designed to minimize cosmetic defects induced by molding process (sink, blush, weld lines, gate
marks, ejector marks, etc.).
•
Painting to cover up cosmetic defects due to molding is strongly discouraged.
5.9 Plastics flammability
•
All Plastics expect Base / Pedestal to be Flame Retardant UL 94-V0 or Better (if monitor weighs less than 18kg;
UL94-V0 is OK).
•
Base / Pedestal to be Flame Retardant UL 94-HB.
•
All major plastic parts (bezel, back cover) need to be molded from same resin. Base / Pedestal otherwise
specified.
5.10 Texture/Glossing of housing
•
The texture area and texture no. should follow Philips make-up sheet.
•
The exterior surfaces shall have a uniform texture.
•
Philips must approve the mold texturing.
•
Detail document for texture refer to UAN-D249.
•
< = 20 gloss units
5.11 Tilt/Swivel Base ranges
•
Tilt Range -
Up = 14° ± 1°, Down = 3.5° ± 1°
•
Swivel Range -
± 90°
•
Base should not break plastic when attempting to rotate it past the stops.
74
17” CDT Color Monitor
107B7
5.12 Movement of unit with base
•
Base must have non-marring, non-staining feet.
•
Unit must tilt up and down with no “Stick / Slip”.
•
Base must provide sufficient friction to hold unit in desired position after adjusting tilt.
5.13 Label
•
Regulatory label / Carton label should follow Philips requirement.
•
Detail documents refer to Philips Engineering Reference Book.
5.14 Product Dimensions / Weight
•
Unit dimension (with stand) -
397mm (W) x 428mm (H) x 423.5mm (D)
•
Packed unit dimension (carton) -
460mm (W) x 450mm (H) x 526mm (D) for China, India
446mm (W) x 420mm (H) x 475mm (D) for other regions
•
Net weight -
13.5 kg
•
Gross weight -
15.8 kg (for China, India)
15.4 kg (for other regions)
5.15 Transportation
Transportation standards refer to UAN-D1534/00 and TYE-M0002
5.15.1 Transportation packages
Packaging and wrapping shall be sufficient to protect the product against damage or loss
during shipment from the supplier to the destination specified in the purchase order. All
packaging materials are subject to test and evaluation per TYE-M0002. The cushion
shall be constructed using EPS material.
material
Carton paper (Double wall AB flute corrugate board, colour brown)
Bursting Compression -
19.3 kgf/cm2 min
670 kgf min
5.15.2 Transportation test procedures
The overall test sequence is: vibration test, drop test and when applicable cold drop test. The sequential tests
have to be carried out using the same packaging.
Vibration, drop test should be performed at ambient temperature (20°C to 23oC) and relative
humidity (40% to 65%).
--- DBC test required and refer to TYE-M0002.
•
Transportation test specification for all regions except China/India, refer to UAN-D1534/01
75
17” CDT Color Monitor
107B7
Sequential tests:
•
1.
Vibration test
2.
Drop test
3.
Single package resonance test (optional)
4.
Compression test
5.
Stacking test (optional)
Transportation test specification for China/India, refer to UAN-D1534/02
Sequential tests:
1.
Vibration test
2.
Bump test
3.
Drop test
4.
Multiple drop tests (after vibration)
5.
Cold drop test when applicable (after vibration)
6.
Compression test
7.
Stacking test (optional)
5.16 Pallet / Container loading
•
Air shipment -
•
Sea container 20'(pallet/slip sheet) -
300 sets with pallet
310 sets without pallet
•
Sea container 40'(pallet/slip sheet) -
630 sets with pallet
635 sets without pallet
•
Sea container 40' High Cube (pallet/slip sheet) - 756 sets with slip sheet
•
Truck shipment for China -
tbc
400 sets
Table 5.16.1. Air shipment container loading
TBC
Table 5.16.2. Sea shipment container loading for China & India
Quantity
Layers
Sets/Layer (PA)
Sets/Layer (PB)
Container size
40’
20’
40’ High Cube
PWHC 45'
W/
W/
W/
W/ Pallet
W/ Pallet
W/ Pallet
W/ Pallet
W/ SLIP
SLIP
SLIP
SLIP
Yes No SHEET Yes No SHEET Yes No SHEET Yes No SHEET
4
4
5
4
4
4
2
NA
2
76
17” CDT Color Monitor
Sets/Block (PA)
Sets/Block (PB)
Blocks/Container
(PA)
Blocks/Container
(PB)
Total sets
107B7
16
8
16
NA
20
10
24
12
24
2
400
NA
192
2
500
Table 5.16.3. Sea shipment container loading for other regions
Quantity
Layers
Sets/Layer (PA)
Sets/Layer (PB)
Sets/Block (PA)
Sets/Block (PB)
Blocks/Container
(PA)
Blocks/Container
(PB)
Total sets
Container size
40’
20’
40’ High Cube
PWHC 45'
W/
W/
W/
W/ Pallet
W/ Pallet
W/ Pallet
W/ Pallet
W/ SLIP
SLIP
SLIP
SLIP
Yes No SHEET Yes No SHEET Yes No SHEET Yes No SHEET
5
5
5
5
5
6
6
6
6
6
6
6
NA
NA
NA
NA
NA
30
30
30
30
30
36
NA
NA
NA
NA
NA
21
21
10
10
21
21
NA
630
NA
630
NA
300
NA
300
NA
630
756
Table 5.16.4. Truck loading for China
TBC
6.0 Reliability / Environment / Transportation
6.1 MTBF Prediction
> 100k hours (excluding CRT)
6.2 Demonstration MTBF > 75k hours (excluding CRT)
6.3 Temperature
•
•
•
Operating (guaranteed performance according to spec requirements): 0 to 40 degree
Storage -20 to 60 ºC
Shipping -40 to 65 ºC
6.4 Humidity
•
•
Operating (non-condensing) Storage (non-condensing) -
5 to 90%
5 to 95%
77
17” CDT Color Monitor
•
107B7
Shipping (non-condensing) -
5 to 95%
6.5 Altitude
•
•
•
Operating Storage Shipping -
0 to 10,000 ft
0 to 35,000 ft
0 to 35,000 ft
6.6 Air pressure
•
•
•
Operating Storage Shipping -
700 to 1100 mbar
300 to 1100 mbar
300 to 1100 mbar
6.7 Earth magnetic field
North Hemispheric
South Hemispheric
Equatorial
H=0, V=450, Z=0mG
H=0, V= -500, Z=0mG
H=0, V=0, Z=0mG
7. REGULATORY COMPLIANCE
7.1 Worldwide regulatory -
International Regulatory Specification
Country
Domain
INTERNATIONAL
Sa
IEC60950-1: 2001. Group -and national
differences of all countries listed in CB
Bulletin No. 107A
Sa
European Low Voltage Directives
73/23/EEC and 93/68/EEC
Documents
CB Report and CB certificate
Declaration of Conformity
European Electromagnetic Compatibility
Directive 89/336/EEC amended by the
directive 93/68/EEC. EN 55022:1998
Class B
EUROPE
E
GERMANY
Safety / Emc / Ergonomics / Standards
Sa
EN 55024: 1998
Declaration of Conformity and
Full EMC/CE test report
EN 61000-3-2: 2000
IEC 61000-3-3: 1994/EN61000-3-3:
1995
CISPR 22:1997 Class B International
EMC standard
EN60950-1: 2001
78
TUV certificate
17” CDT Color Monitor
SWEDEN
RUSSIA
SOUTH AFRICA
USA
CANADA
MEXICO
KOREA
SINGAPORE
CHINA
TAIWAN
AUSTRALIA/
NEW-ZEALAND
ISRAEL
Saudi Arabia
Japan
Argentina
107B7
O
ISO 9241-3-7-8 (CRT) & 13406-2 (LCD),
prEN 50279:1998
O
GS-Mark / EK1-ITB 2000
X
Decree
Sa
EN60950-1: 2001
O
TCO 99 (TCO03) (to TCO models)
O
MPR 1990: 8 / MPR 1990:10 (to MPR
models)
Meet requirement
Sa
GOST R 50377-1992
GOST certificate
Sa
SABS IEC 60950 and IEC 60950-1
Certificate of Conformity
E
EN55022 or Cisper 22
Certificate of Conformity
Sa
UL 60950-1: 2003
UL certificate
E
FCC Part 15 Class B
FCC ID grant or DOC
O
Energy Star
X
21CFR 1002.10 to 13 (CRT)
Sa
CSA C22.2 No 60950
E
ICES-003 issue 3
E
RED (CRT)
Sa
NOM-019-SCFI-1994
Sa
Korean Safety Control law IEC 60950
E
Regulations laws: EMI 1996-78, 80. EMS
1996-79,81
MIC certificate
Sa
IEC60950
PSB certificate
Sa
GB4943-2001
E
GB9254-1998; 17625.1-2003
O
CSC/G1205-2004
Sa
CNS-14336
E
CNS-13438 (CISPR22) Class B
O
Criteria 18 (Monitor) (LCD)
E
AS/NZS3548: 1995
Declaration of Conformity
S
IS 1121, IEC60950/IEC60950-1
Certificate of Conformity
E
EN or Cisper 22
Certificate of Conformity
S
IEC standard
SASO
E
IEC standard
SASO
Sa
EN60950-1:001 (AC adapter only)
E
VCCI class B (CISPR 22)
Sa
EN60950-1: 2001
TUV-ERG certificate
TUV-GS certificate
ROV 08.01.87 (CRT)
PTB
SEMKO certificate
TCO99 (TCO03) report +
certificate
EPA registration
DHHS report
CSA certificate
Statement on label
DNHW
NOM certificate
eK certificate
CCC certificate
CECP certificate
(IEC 60950-1)
BSMI certificate
Green Mark / certificate
PSE
VCCI Certificate
IRAM
Sa = Safety
79
17” CDT Color Monitor
107B7
E = Electromagnetic Compatibility
O = Other which including recycling, energy saving, ergonomics
X = X-ray
For detailed regulatory items please refer to the international regulatory specification provided by
Philips.
7.2 EMC requirements
Supplier DVT EMI test result must be submitted prior to DVT samples delivery, and PVT EMI test result must
be submitted again prior to PVT samples delivery. Which also has to meet Philips' immunity testing specification.
7.3 MPR II / TCO
Front Bezel Color Back Cover Color
CTV
107B70
107B75
Grey
Black
Grey
Black
MPRII
TCO-99
TCO-03
X
X
X
X
Y
Y
7.4 RoHS
Restriction on the use of certain hazardous substances.
Lead, Cadmium, Mercury, Hexavalent Chromium, Polybrominated Bipheny1 (PBB) and
Polybrominated Bipheny1 Ether (PBDE) (flame retardant).
7.5 WEEE
Producer’s responsibility for retailer takes back schemes and recycling.
--System implemented.
--Collection and recycle targets.
7.6 Ongoing regulatory
There's a possibility that other regulatory certificates will be required during the life of the product. It is the
responsibility of the supplier to provide related documentation.
80