Ethernet Extension Experts
™
Enable-IT 820P Pro Series
Extended Ethernet
Quickstart Guide
All Rights Reserved ©1997 - 2012 ENABLE-IT™ - Proprietary and Confidential
INSTALLING THE 820P PRO EXTENDED ETHERNET KIT
The Enable-IT 820P Pro Extended Ethernet Kit has a distance restriction of 800ft or
244m over Category 2 up to Category 6 wiring from device extension to device
extension. Therefore quick, simple site surveys and installation planning are highly
recommended.
This chapter describes the recommended installation process for the Enable-IT 820P
Pro Extended Ethernet Kit. It covers the following topics:
•
•
•
Site Plan – Installation Design Considerations
Unpacking the Enable-IT 820P Pro Extended Ethernet Kit
Performing the On-Site Installation
Site Plan - Installation Design Considerations
•
•
•
•
•
•
Total distance of 1,100ft wiring from 350 PoE Injector to LAN device on the
remote end.
4 Pair Telco wiring for the Enable-IT 820P Pro Extended Ethernet Unit.
Wire pair used must be straight through, no taps/connection points.
Twisted Pair cabling delivers the best performance over distance.
Cisco PoE single line injector support built in.
Transparent to single line 802.3af PoE or 802.3at PoE Plus devices.
Option 1 – Single line PoE LAN Extension up to 800ft / 244m
We highly recommend a quick test to ensure the working order of your 820P Pro
unit. To do this, please power on the 350 PoE Injector. Attach a patch cord from
your LAN source to the PoE/Data IN port on the injector. Then run another patch
cord from the PoE/Data OUT port to the LAN & PoE IN port on the 820P Pro unit.
Next, use one of the Ethernet patch cords provided and attach one end to the
Interlink Out port on the 820P Pro unit and the other end connected to your
remote PoE device. The 820P Pro unit and your PoE LAN device should now be
powered up and running.
Network Configuration
In some instances, your Ethernet switch, desktop computer, laptop, WiFi Access Point,
or any LAN device not mentioned may need to be configured for 10Mbps auto-sensing
as the 820 Pro is a 10Mbps Ethernet switch. It may be the case that your Ethernet
switch is not passing data through the 820 Pro to your remote LAN device, therefore
setting the LAN configuration on your device to 10Mbps will allow it to recognize the 820
Pro switch settings.
Page 2 of 5
Option 2 – Single line PoE LAN Extension up to 1,600ft using an additional 820P
Pro device daisy-chained with the original.
To do this, please power on the 350 PoE Injector with the supplied power cord.
Attach a patch cord from your originating LAN source to the PoE/Data IN port on
the injector. Then run another patch cord from the PoE/Data OUT port to the LAN
& PoE IN port on the 820 Pro unit. Now you may daisy chain the 2nd 820P Pro unit
by connecting a patch cord from the Interlink Out port on your 1st 820P to the
LAN & PoE IN port on the 2nd 820P Pro unit. Next, attach a PoE LAN device to the
Interlink Out port on the 2nd 820P Pro unit. The 820P Pro units as well as your
remote PoE device should now be powered up and running.
LED indicators will provide visual operational status of the 820P Pro units.
820 LAN & PoE IN – Slow yellow LED flashing indicates LAN connectivity.
Flickering yellow LED indicates LAN traffic.
820 Interlink Out – Solid green LED indicates PoE power.
DIP Switch Settings: DIP switches 1 – 4:
Down (ON) - Enable PoE pass-through
UP (OFF) – Disable PoE pass-through
Default DIP Settings: DIP switches 1 – 4:
Down (ON) PoE Enabled for Data / PoE use
For installation at your desired location, keep in mind the following:
The backbone cable between the CO and your end device – RJ-45 Interlink ports uses
all 4-pairs of wiring for data and PoE (1, 2, 3 & 6 for data and 4, 5, 7 & 8 for PoE).
DO NOT INSERT ANY BLANK RJ-45 HEADS
INTO ANY PORTS BEFORE CRIMPING –
OTHERWISE YOU WILL RENDER THE PORT
USELESS – BENT PINS
Attach RJ-45 Male heads to your existing
wiring and follow the diagram below. For data
only use pins 1,2,3 & 6. For Data and PoE use
all pins. PoE uses pins 4,5,7 & 8
Page 3 of 5
Unpacking the Enable-IT 820P Pro Extended Ethernet Kit
Carefully remove the Enable-IT 820P Pro Extended Ethernet Unit and all packing
materials from the box. Verify that the items listed below are present. Make sure that the
equipment supplied matches what you ordered. If any items are missing or damaged,
please contact your Enable-IT or your distributor for assistance.
•
•
•
•
(1) Enable-IT 820P Pro Extended Ethernet Unit
(1) Enable-IT 350 PoE Injector 20W – 48v & power cord
(1) LAN Ethernet Patch Cord for end device attachment
(1) Enable-IT Quickstart Guide
Technical Support
Enable-IT OEM Technical Support is available directly to customers and distributors. All
support requests are processed through the online support portal. This allows us to provide
assigned support ticket numbers in order to bring closure to any technical issues.
Online Technical Services
The Enable-IT Support Portal is available 24/7. No password or user account is necessary.
Please use this support website as your first source for help as it contains an on line
knowledge base of articles, documentation, FAQ's and other problem-solving resources. This
web-based support resource provides the quickest solution to the most common technical
support issues.
http://support.enableit.com
Returning Products for Warranty Repair
Enable-IT, Inc. warrants to the original purchaser of the Product ("you" or the "End User")
that, for the four (4) year period commencing on the date the Product was purchased (the
"Warranty Period"), the Product will be substantially free from defects in materials and
workmanship under normal use and conditions. Electrical damage is not an item that is
covered under this warranty or extended warranties.
If authorized by Enable-IT to return a Product which does not conform to the warranty set
forth above, the End User must: (1) obtain a return materials authorization (RMA) number
from Enable-IT by contacting the Customer Service Dept. at 888-309-0910 between the
hours of 8:00 a.m. and 5:00 p.m. PST and otherwise fully comply with Enable-IT’s then
current RMA policy; (2) return the Product to Enable-IT, Inc. in its original packaging freight
pre-paid; and (3) provide to Enable-IT the original receipt or bill of sale establishing the date
on which the Product was purchased.
Please ship Authorized RMAs to:
Enable-IT Processing Facility
16600 Harbor Blvd, Ste I (India)
Fountain Valley, CA 92708
Returning Products for Refund
45-Day refund applies to single kit Ethernet
Extenders only and is subject to a 15%
Restocking Fee.
Shipments without valid /
authorized RMA number or sent to our corporate
Las Vegas Address can be refused and or billed
for additional shipping.
Page 4 of 5
CONTACT US
European Sales:
+44 1 908 560200
+44 1 908 565533 fax
http://www.enable-it.eu
sales@enable-it.eu
North American Sales:
+1 888 309-0910
+1 866 389-8605 fax
http://www.enableit.com
sales@enableit.com
Middle East Sales:
+971-50-435-8310
http://www.enableit.com
sales@enableit.com
Other International:
+1 702 924-0402
+1 702 800-2711 fax
Page 5 of 5
Asia Pacific Sales:
+61 02 8898-9622
+61 2 9939-0005 fax
http://www.enable-it.com.au
sales@enable-it.com.au