Smart 132973880.qxd
23/06/2008
12.22
User
manual
Washing
Machine
ZWF 14581 W
Pagina
1
Smart 132973880.qxd
23/06/2008
12.22
Pagina
2
Thank you for selecting our appliance
We wish you lots of enjoyment with your new appliance and we hope that you will consider our
brand again when purchasing household appliances.
Please read this user manual carefully and keep it throughout the product life cycle as a reference
document. The user manual should be passed on to any future owner of the appliance.
The following symbols are used in this manual:
Important information concerning your personal safety and information on how to avoid
damaging the appliance.
General information and tips
Environmental information
Content
Safety information - - - - - - - - - - - - - - - - - - -3
Care and cleaning - - - - - - - - - - - - - - - - - -20
Description of the appliance - - - - - - - - - - - -5
Something not working - - - - - - - - - - - - - - 23
Detergent dispenser drawer - - - - - - - - - - - -5
Technical data- - - - - - - - - - - - - - - - - - - - - 26
Control panel and functions - - - - - - - - - - - -6
Consumption values - - - - - - - - - - - - - - 26-27
Programme table - - - - - - - - - - - - - - - - - - -7
Installation instruction - - - - - - - - - - - - - - - 28
Programme information - - - - - - - - - - - - - -10
Environmental concerns - - - - - - - - - - - - - 32
Washing Hints - - - - - - - - - - - - - - - - - - - - -12
Guarantee conditions - - - - - - - - - - - - - - - 33
Before the first use - - - - - - - - - - - - - - - - -14
European guarantee - - - - - - - - - - - - - - - - 34
Operating Sequence - - - - - - - - - - - - - - - -15
2
Smart 132973880.qxd
23/06/2008
12.22
Pagina
3
Safety information
In the interest of your safety and to ensure
the correct use, before installing and first
using the appliance, read this user manual
carefully, including its hints and warnings.
To avoid unnecessary mistakes and
accidents, it is important to ensure that all
people using the appliance are thoroughly
familiar with its operation and safety
features. Save these instructions and make
sure that they remain with the appliance if it
is moved or sold, so that everyone using it
through its life will be properly informed on
appliance use and safety.
●
●
Installation
●
●
General safety
●
●
●
●
●
●
●
It is dangerous to alter the specifications or
attempt to modify this product in any way.
During high temperature wash programmes
the door glass may get hot. Do not touch it!
Make sure that small pets do not climb into
the drum. To avoid this, please check into
the drum before using.
Any objects such as coins, safety pins, nails,
screws, stones or any other hard, sharp
material can cause extensive damage and
must not be placed into the machine.
Only use the advised quantities of fabric
softener and detergent. Damage to the fabric
can ensue if you over-fill. Refer to the
manufacturer’s recommendations of
quantities.
Wash small items such as socks, laces,
washable belts etc in a washing bag or
pillow case as it is possible for such items to
slip down between the tub and the inner
drum.
Do not use your washing machine to wash
articles with whalebones, material without
hems or torn material.
Always unplug the appliance and turn off the
water supply after use.
Under no circumstances should you attempt
to repair the machine yourself. Repairs
carried out by inexperienced persons may
cause injury or serious malfunctioning.
Contact your local Service Centre. Always
insist on genuine spare parts.
●
●
●
●
●
●
●
This appliance is heavy. Care should be
taken when moving it.
When unpacking the appliance, check that it
is not damaged. If in doubt, do not use it and
contact the Service Centre.
All packing and transit bolts must be
removed before use. Serious damage can
occur to the product and to property if this is
not adhered to. See relevant section in the
user manual.
After having installed the appliance, check
that it is not standing on the inlet and drain
hose and the worktop is not pressing the
electrical supply cable.
If the machine is situated on a carpeted floor,
please adjust the feet in order to allow air to
circulate freely under the appliance.
Always be sure, that there is no water
leakage from hoses and their connections
after the installation.
If the appliance is installed in a location
subject to frost, please read the «dangers of
freezing» chapter.
Any plumbing work required to install this
appliance should be carried out by a
qualified plumber or competent person.
Any electrical work required to install this
appliance should be carried out by a
qualified electrician or competent person.
Use
3
Smart 132973880.qxd
●
●
●
●
●
●
●
23/06/2008
12.22
Pagina
This appliance is designed for domestic use.
It must not be used for purposes other than
those for which it was designed.
Only wash fabrics which are designed to be
machine washed. Follow the instructions on
each garment label.
Do not overload the appliance. See the
relevant section in the user manual.
Before washing, ensure that all pockets are
empty and buttons and zips are fastened.
Avoid washing frayed or torn articles and
treat stains such as paint, ink, rust, and
grass before washing. Underwired bras must
NOT be machine washed.
Garments which have been in contact with
volatile petroleum products should not be
machine washed. If volatile cleaning fluids
are used, care should be taken to ensure
that the fluid is removed from the garment
before placing in the machine.
Never pull the power supply cable to remove
the plug from the socket; always take hold of
the plug itself.
Never use the washing machine if the power
supply cable, the control panel, the working
surface or the base are damaged so that the
inside of the washing machine is accessible.
Child safety
●
●
●
●
4
This washing machine is not intended for
use by young children or infirm persons
without supervision.
Young children should be supervised to
ensure that they do not play with the
appliance.
The packaging components (e.g. plastic film,
polystyrene) can be dangerous to children danger of suffocation! Keep them out of
children’s reach
Keep all detergents in a safe place out of
children’s reach.
●
4
Make sure that children or pets do not climb
into the drum. To avoid children or pets
becoming trapped inside the drum, the
machine incorporates special feature.
To activate this device,
rotate the button
(without pressing it)
inside the door
clockwise until the
groove is horizontal. If
necessary use a coin.
To disable this device
and restore the
possibility of closing the
door, rotate the button
anti-clockwise until the
groove is vertical.
Smart 132973880.qxd
23/06/2008
12.22
Pagina
5
Description of the appliance
Your new washing machine is fitted with an automatic device which detects the laundry amount in
some programmes for cotton and synthetic items and chooses the best cycles parameters for
washing in an economical way. Cycle time duration, energy and water consumptions are
proportional to the amount of each load.
It is ideal when washing different small quantities of laundry.
1
Detergent dispenser drawer
2
Control panel
3
Door opening handle
4
Drain pump
5
1
2
Delay Start
Sport 40°
Sport Shoes 40°
Off
Jetsystem+
Cotton
Cotton Eco
Synthetic
Cottons
Normal
Wool
Handwash
Silk
1400 7kg
+Prewash
95º
1400
60º
900
40º
700
Normal
Heavy
Normal
30º
Lock
Light
+Superquick
Duvet
Mini 30'
Special
Rinse
Temp.
Spin
Soil Level
Easy Iron
Extra Rinse
Start/Pause
+Prewash
Drain
Spin
+Superquick
Synthetics
Delicate
ZWF14581W
Adjustable feet
3
4
5
Detergent dispenser drawer
Prewash
Wash
Fabric Softener
5
Smart 132973880.qxd
23/06/2008
12.22
Pagina
6
Control panel and functions
Delay Start
Sport 40°
Sport Shoes 40°
Jetsystem+
Cotton
Cotton Eco
Off
95º
Synthetic
Cottons
Normal
Wool
Handwash
Silk
900
40º
700
Lock
Light
+Superquick
Mini 30'
Special
Rinse
Heavy
Normal
30º
+Prewash
Duvet
Temp.
Normal
Spin
Soil Level
Easy Iron
Start/Pause
Extra Rinse
+Prewash
Drain
Spin
+Superquick
Synthetics
Delicate
ZWF14581W
1
2
●
1
1400
60º
Programme selector dial and
On/Off switch
●
2 Temperature button
3
4
5
6
7
8
9
The programme selector dial allows you to select a
programme and/or to switch the machine on/off. It can be
turned either clockwise or anticlockwise. The light
Start/Pause starts to flash.
Press this button repeatedly to change the washing
temperature, if you want your laundry to be washed at a
temperature different from the one proposed by the washing
machine. The relevant light will light up.
Press the Spin button repeatedly to change the spin speed,
if you want your laundry to be spun at a speed different from
the one proposed by the washing machine. The relevant
light will light up.
● By means of this button, you can select the soil level option:
Heavy, Normal, Light (see the relevant chapter «Operating
sequence»).
● The relevant light will light up.
●
3 Spin reduction button
4 Soil level button
5 Easy iron button
●
6 Extra Rinse button
●
●
7
6
Display
Selecting this button the laundry is gently washed and spun
to avoid any creasing. In this way ironing is easier.
By means of this button, the machine performs some
additional rinses.
The display shows the following information: duration of the
selected programme, washing programme phase icons,
delayed start, weight calculation phase, incorrect option
selection, alarm codes, child safety option, heating phase
and end of programme.
Smart 132973880.qxd
23/06/2008
12.22
●
8 Start/Pause button
●
9 Delay Start buttons
●
Pagina
7
The Start/Pause button allows you to start the selected
programme; the corresponding green pilot light stops
flashing.
This button also interrupts a programme which is running, the
corresponding green pilot light starts to flash.
By means of this buttons, the wash programme can be
delayed from 30 mins - 60 mins - 90 mins, 2 hours and then
by 1 hour up to a maximum of 20 hours .
Programme table - Proportional programmes
Programme/
Temperature
Cotton
95 Proportional
Cotton Eco
60- 40
Proportional
Synthetic
60 Proportional
Type of laundry
White and coloured
cotton (Normally soiled):
e.g. sheets, tablecloths,
household linen, towels.
White and fast
coloured cotton
(normally or lightly soiled
items): sheets, household
linen, underwear
Synthetic or mixed
fabrics, underwear,
coloured garments, nonshrink shirts, blouses.
Options
Description of
programme
Main wash from 95°C
Spin red.
to
Cold
Heavy, Light,
3 rinses
Easy iron, Extra rinse Long spin
Spin red.
Easy iron
Extra rinse
Main wash from
60°C to 40°C
2 rinses
Long spin
Main wash from 60°C
Spin red.
to
Cold
Heavy, Light,
3 rinses
Easy iron, Extra rinse Short spin
Cycle time duration, energy and water consumptions are proportional to the amount of load.
Important!
When selecting these programmes the «Normal» pilot light illuminates.
7
Smart 132973880.qxd
23/06/2008
12.22
Pagina
8
Programme table
Programme/
Temperature
Type of laundry
Options
Description of
programme
Cottons
Normal
95 -
White and coloured
cotton cotton (normally
soiled items): sheets,
tablecloths, household
linen, towels.
Spin red.
Heavy, Easy iron,
Extra rinse
Main wash from 95°C
to
Cold
3 rinses
Long spin
Cottons
+ Prewash
95 -
White and coloured
cotton (heavy soiled
cotton items): sheets,
household linen,
underwear
Spin red.
Heavy, Easy iron
Extra rinse
Prewash at 30°C
Main wash from
95°C to
Cold
3 rinses
Long spin
Cottons
+ SuperQuick
95 -
White cotton (slightly
soiled items): e.g.
sheets, tablecloths,
household linen, towels.
Synthetics
Normal
60 -
Synthetic or mixed
fabrics, underwear,
coloured garments, nonshrink shirts, blouses.
Spin red.
Easy iron,
Extra rinse
Main wash from 60°C
to
Cold
3 rinses
Short spin
Synthetics
+ Prewash
60 -
Synthetic or mixed
fabrics, underwear,
coloured garments, nonshrink shirts, blouses.
Spin red.
Easy Iron
Extra rinse
Prewash at 30°C
Main wash from
60° to
Cold
3 rinses
Short spin
Synthetics
+ SuperQuick
60 -
Synthetic or mixed
fabrics lightly soiled
Spin red.
Easy iron,
Extra rinse
Main wash from
60° to
Cold
2 rinses
Short spin
Delicates
40-
Delicate fabrics, for
example curtains.
Max load for Cottons ..............................7.0 kg
Max load for Synthetics ..........................3.5 kg
Max load for Delicates ............................3.5 kg
8
Main wash from 95°C
to
Cold
Spin red.
Easy iron, Extra rinse 2 rinses
Long spin
Extra Rinse
Main wash from
40°C to
Cold
3 rinses
Short spin
Smart 132973880.qxd
23/06/2008
12.22
Pagina
9
Programme table - Special programmes
Programme/
Temperature
Type of laundry
Options
Description of
programme
Mini 30’
30
Short cycle for lightly
soiled fabrics
Main Wash at 30°C
2 rinses
Short spin
Duvet
30
Short cycle for blankets
Main Wash at 30°C
3 rinses
Short spin
Silk
30
Silk items to be gently
washed and spun.
Main wash at 30°C
2 rinses
Short spin
Handwash
40 -
Special programme for
hand washing fabrics
Spin red.,
,
Wool
40 -
Programme for wool
«Pure new wool, nonshrink, machine
washable» label.
Spin red.,
,
Sport Shoes 40°
40
Sport 40°
40
Short cycle for 1 pair of
sport shoes.
Spin Red./
Programme for heavily
soiled synthetics items
Spin Red./
Max load for Wool/Handwash/Duvet ........ 2 kg
Max load for Mini 30’/Sport 40° ............ 2.5 kg
Max load for Silk ........................................1 kg
Extra rinse
,
Extra rinse
Main wash from
40° to
Cold
3 rinses
Short spin
Main wash from
40° to
Cold
3 rinses
Short spin
Main Wash at 40°C
3 rinses
Short spin
Prewash at 30°C
Main wash at 40°C
3 rinses
Short spin
Max load for Sport Shoes 40° ................1 pair
9
Smart 132973880.qxd
23/06/2008
12.22
Pagina
10
Programme table
Programme/
Temperature
Spin
Drain
Rinse
Type of laundry
Separate spin for
cottons.
Options
Spin red.
Description of
programme
Drain and long spin
For emptying out the last
rinse water in
Draining of water
programmes with the
Rinse Hold
or Night
Cycle
option.
Separate rinse cycle
3 rinses
Spin red.
for hand washed
Easy iron, Extra rinse Long spin
items of all fabric.
Programme information
Wool and
Handwash
Washing programme for machine washable wool as well as for hand
washable woollens and delicate fabrics with the «hand washing»
care symbol
.
Easy Iron
Selecting this button the laundry is gently washed and spun to avoid
any creasing. In this way ironing is easier. Furthermore the machine
will perform additional rinses.
On cotton programmes the spin speed will automatically be reduced
to 900 rpm.
Rinse
With this programme it is possible to rinse and spin cotton garments
which have been washed by hand.
The machine performs 3 rinses, followed by a final spin at maximum
speed.
The spin speed can be reduced by depressing Spin button.
Drain
For emptying out the water of the last rinse in cotton programmes
with the Rinse Hold
and Night Cycle
option.
Turn first the programme selector dial to «Off», then select
programme Drain and depress the Start/Pause button.
10
Smart 132973880.qxd
23/06/2008
12.22
Pagina
11
Programme information
Spin
Separate spin for hand washed garments and after programmes
with Rinse Hold
and Night Cycle
option. Before selecting
this programme the selector dial must be turned to Off. You can
choose the speed by means of the relevant button to adapt it to the
fabrics to be spun.
Mini 30’
This special short programme is a complete washing cycle for lightly
soiled mixed fabrics /synthetic items or laundry which needs
freshening up. The short spin is performed at 700 rpm. The cycle
duration is about 30 minutes.
Duvet
Washing programme for a single synthetic duvet, blanket,
bedspread etc. The washing temperature is 30°C. The spin is
performed at 700 rpm.
Silk
Delicate washing programme suitable for silk and mixed synthetics
items. Washing temperature is 30°C.
The maximum spin speed is automatically reduced to 700 rpm.
Sport shoes 40°
With this programme it is possible to wash one pair of sport shoes
(or 2 pairs if they are small). The shoes would be gently washed and
spun. Washing temperature 40°C.
Note! Do not wash your sport shoes together with laundry.
Sport 40°
This programme is suitable for washing heavily soiled sport items of
synthetic fabrics. The machine will add automatically a prewash
phase before the main wash to eliminate mud stains.
Note ! We recommend that you do not put the detergent into the
compartent
of the detergent drawer.
The spin speed is reduced to 900 rpm.
Off = Cancelling
To reset a programme and to switch off the machine turn the
selector dial to Off. Now a new programme can be selected.
11
Smart 132973880.qxd
23/06/2008
12.22
Pagina
12
Washing hints
Sorting the laundry
Maximum loads
Follow the wash code symbols on each
garment label and the manufacturer’s washing
instructions. Sort the laundry as follows: whites,
coloureds, synthetics, delicates, woollens.
Recommended loads are indicated in the
programme charts.
General rules:
Cotton, linen: drum full but not too tightly
packed;
Synthetics: drum no more than half full;
Delicate fabrics and woollens: drum no more
than one third full.
Washing a maximum load makes the most
efficient use of water and energy.
For heavily soiled laundry, reduce the load
size.
Temperatures
90° or 95°
for normally soiled white cottons
and linen (e.g. tea cloths, towels,
tablecloths, sheets...)
50°/60°
for normally soiled, colour fast
garments (e.g. shirts, night
dresses, pyjamas....) in linen,
cotton or synthetic fibres and for
lightly soiled white cotton (e.g.
underwear).
30°-40°(Cold)
for delicate items (e.g. net
curtains), mixed laundry including
synthetic fibres and woollens
bearing the label «pure new wool,
machine washable, non-shrink».
Before loading the laundry
Never wash whites and coloureds together.
Whites may lose their «whiteness» in the
wash.
New coloured items may run in the first wash;
they should therefore be washed separately
the first time.
Make sure that no metal objects are left in
the laundry (e.g. hair clips, safety pins,
pins). Button up pillowcases, close zip
fasteners, hooks and poppers. Tie any belts
or long tapes.
Remove persistent stains before washing.
Rub particularly soiled areas with a special
detergent or detergent paste.
Treat curtains with special care. Remove hooks
or tie them up in a bag or net.
12
Laundry weights
The following weights are indicative:
bathrobe
napkin
quilt cover
sheet
pillow case
tablecloth
towelling towel
tea cloth
night dress
ladies’ briefs
man’s work shirt
man’s shirt
man’s pyjamas
blouse
men’s underpants
1200 g
100 g
700 g
500 g
200 g
250 g
200 g
100 g
200 g
100 g
600 g
200 g
500 g
100 g
100 g
Removing stains
Stubborn stains may not be removed by just
water and detergent. It is therefore advisable to
treat them prior to washing.
Blood: treat fresh stains with cold water. For
dried stains, soak overnight in water with a
special detergent then rub in the soap and
water.
Smart 132973880.qxd
23/06/2008
12.22
Pagina
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth and
dab the stain; treat several times.
Dried grease stains: moisten with turpentine,
lay the garment on a soft surface and dab the
stain with the fingertips and a cotton cloth.
Rust: oxalic acid dissolved in hot water or a
rust removing product used cold. Be careful
with rust stains which are not recent since the
cellulose structure will have already been
damaged and the fabric tends to hole.
Mould stains: treat with bleach, rinse well
(whites and fast coloureds only).
Grass: soap lightly and treat with bleach
(whites and fast coloureds only).
Ball point pen and glue: moisten with
acetone (*), lay the garment on a soft cloth and
dab the stain.
Lipstick: moisten with acetone as above, then
treat stains with methylated spirits. Remove
any residual marks from white fabrics with
bleach.
Red wine: soak in water and detergent, rinse
and treat with acetic or citric acid, then rinse.
Treat any residual marks with bleach.
Ink: depending on the type of ink, moisten the
fabric first with acetone (*), then with acetic
acid; treat any residual marks on white fabrics
with bleach and then rinse thoroughly.
Tar stains: first treat with stain remover,
methylated spirits or benzine, then rub with
detergent paste.
13
etc.), the colour, washing temperature and
degree of soiling.
All commonly available washing machine
detergents may be used in this appliance:
● powder detergents for all types of fabric,
● powder detergents for delicate fabrics (60°C
max) and woollens,
● liquid detergents, preferably for low
temperature wash programmes (60°C max)
for all types of fabric, or special for woollens
only.
The detergent and any additives must be
placed in the appropriate compartments of the
dispenser drawer before starting the wash
programme.
If using concentrated powder or liquid
detergents, a programme without prewash
must be selected.
The washing machine incorporates a
recirculation system which allows an optimal
use of the concentrated detergent.
Pour liquid detergent into the dispenser drawer
compartment marked
just before starting
the programme.
Any fabric softener or starching additives must
be poured into the compartment marked
before starting the wash programme.
Follow the product manufacturer’s
recommendations on quantities to use and do
not exceed the «MAX» mark in the
detergent dispenser drawer.
(*) do not use acetone on artificial silk.
Detergents and additives
Good washing results also depend on the
choice of detergent and use of the correct
quantities to avoid waste and protect the
environment. Although biodegradable,
detergents contain substances which, in large
quantities, can upset the delicate balance of
nature.
The choice of detergent will depend on the
type of fabric (delicates, woollens, cottons,
13
Smart 132973880.qxd
23/06/2008
12.22
Pagina
14
Quantity of detergent to be used
The type and quantity of detergent will depend
on the type of fabric, load size, degree of
soiling and hardness of the water used.
Water hardness is classified in so-called
«degrees» of hardness. Information on
hardness of the water in your area can be
obtained from the relevant water supply
company, or from your local authority.
Follow the product manufacturers’ instructions
on quantities to use.
Degrees of water hardness
Follow the product manufacturers’ instructions
on quantities to use.
Before the first use
WARNING!
Ensure that the electrical and water
connections comply with the installation
instructions.
IMPORTANT!
Remove the polystyrene block and any
material from the drum.
IMPORTANT!
We recommend you to run run a cotton cycle
at 95°C, without any laundry in the machine, to
remove any manufacturing residue from the
drum and tub. Pour 1/2 a measure of detergent
into the dispenser drawer and start the
machine.
14
Degrees
Level
Characteristic
German
°dH
French
°T.H.
1
soft
0-7
0-15
2
medium
8-14
16-25
3
hard
15-21
26-37
4
very hard
> 21
> 37
Use less detergent if:
● you are washing a small load,
● the laundry is lightly soiled,
● large amounts of foam form during washing.
Smart 132973880.qxd
23/06/2008
12.22
Pagina
15
Operating sequence
1. Load the laundry
Open the door by
carefully pulling the
door handle outwards.
Place the laundry in the
drum, one item at a
time, shaking them out
as much as possible. Close the door.
2. Measure out the detergent and the fabric
softener
The Start/Pause light starts to flash, the display
shows the duration of the selected programme.
At the end of the programme the selector
dial must be turned to position «Off», to
switch the machine off.
IMPORTANT!
If you turn the programme selector dial to
another programme when the machine is
working, the red Start/Pause pilot light will
flash 3 times and the message Err is displayed
on the display to indicate a wrong selection.
The machine will not perform the new selected
programme.
4. Select the temperature
95º
60º
40º
30º
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent required,
pour it into the main wash compartment
and, if you wish to carry out a programme with
the prewash phase, pour it into the
compartment marked
.
If required, pour fabric softener into the
compartment marked
(the amount used
must not exceed the «MAX» mark in the
drawer). Close the drawer gently.
3. Select the required programme
Sport 40°
Sport Shoes 40°
Off
Jetsystem+
Cotton
Cotton Eco
Synthetic
Cottons
Normal
Wool
Handwash
Silk
+Prewash
+Superquick
Duvet
Mini 30'
Special
Rinse
Normal
+Prewash
Drain
Spin
+Superquick
Synthetics
Delicate
The selector dial is
divided into following
the sections:
● Cottons,
● Synthetics,
● Special
Temp.
Press this button repeatedly to increase or
decrease the temperature, if you want your
laundry to be washed at a temperature
different from the one proposed by the washing
machine.Maximum temperatures are 95°C for
Cottons, 60°C for Synthetics, 40°C for
Delicate, Wool, Handwash, Sport Shoes 40°
and Sport 40°, 30°C for Silk, Duvet and Mini
30’, while
corresponds to cold wash.
Turn the programme selector dial to the
required programme.
15
Smart 132973880.qxd
23/06/2008
12.22
Pagina
16
Operating sequence
5. Select the spin speed or Night Cycle or
Rinse Hold option
1400
900
700
Spin
Press the Spin button repeatedly to change the
spin speed, if you want your laundry to be spun
at a speed different from the one proposed by
the appliance.
The relevant light will light up.
Maximum speeds are:
● Cottons: 1400 rpm;
● Synthetics, Wool, Wandwash, Sport Shoes
40° and Sport 40°: 900 rpm
● Delicate, Mini 30’, Duvet and Silk: 700 rpm;
Night Cycle
: by selecting this option, the
machine will not drain the water of the last
rinse, so as not to crease the laundry. As all
spinning phases are suppressed, this washing
cycle is very quiet and it can be selected at
night or in times with a more economical power
rate.
On Cotton, Synthetics, Delicates, Silk, Sport
Shoes 40° and Sport 40° programmes the
rinses will be performed with more water.
When the programme has finished, the
Start/Pause light goes off, the display shows a
flashing zero «0.00», the «Lock» light is alight
and the door is blocked to indicate that the
water must be emptied out.
Rinse Hold
: by selecting this option the
water of the last rinse is not emptied out to
prevent the fabrics from creasing.
When the programme has finished, the
Start/Pause light goes off, a flashing zero
16
«0.00» appears on the display, the «Lock»
light is alight and the door is locked to indicate
that the water must be emptied out.
To empty out the water:
1. turn the programme selector dial to «Off»
2. select the Drain or Spin programme
3. reduce the spin speed if needed, by means
of the relevant button
4. depress Start/Pause button
5. at the end of programme, the display shows
a flashing zero «0.00» and the «Lock» light
goes off (and it will be possible to open the
door).
6. Select the Soil Level option
Heavy
Normal
Light
Soil Level
Press the «Soil Level»
button repeatedly, to
increase or decrease
the cycle time duration
for cotton and synthetic.
The relevant light will
light up.
IMPORTANT!
Not all the soil levels are compatible and
can be selected with any programme.
Heavy
Select this option for heavily soiled laundry.
The washing intensity will be increased and the
washing time will be prolonged by about 10
minutes.
Normal:
Select this option for normally soiled laundry .
Depending on the selected programme, the
corresponding «Normal » light will
illuminate by default.
Light:
Select this option for slightly soiled items that
have been used or worn for a short time.
Smart 132973880.qxd
23/06/2008
12.22
Pagina
17
Operating sequence
The washing intensity will be decreased and the
washing time will be reduced by few minutes.
the Start/Pause button will flash 3 times.
7 Select the Easy Iron option
The display shows the following information:
Duration of the selected programme
After selecting a programme, the duration is
displayed in hours and minutes (for example
2.05). The duration is calculated automatically
on the basis of the maximum recommended
load for each type of fabric.
By selecting this button
the laundry is gently
washed and spun to
Easy Iron
avoid any creasing. In
this way ironing is
easier. Furthermore the
machine will perform
some additional rinses. This function can be
used for cotton and synthetic.
The Easy iron cannot be selected with the
Night Cycle option.
If you press this button, simultaneously for
about 6 seconds, in combination with Extra
Rinse" button, the child safety lock will be
enabled (see Display paragraph).
8 Select the Extra Rinse option
This button can be
selected with all
Extra Rinse
programmes except
Wool, Hand wash, Mini
30’, Duvet and Silk
programmes. The
machine performs some
additional rinses.
This option is recommended for people who
are allergic to detergents, and in areas where
the water is very soft.
If you press this button, simultaneously for
about 6 seconds, in combination with "Easy
Iron" button the child safety lock will be
enabled (see Display paragraph).
IMPORTANT!
If an option is chosen that is not allowed with
the selected programme, the red pilot light of
9. Display
2.05
After the programme
has started, the time
remaining is updated
every minute.
ATTENTION!
When selecting the «proportional»
programmes, the diplay shows the washing
duration of the maximum recommended load.
After Start/Pause has been pressed, an arrows
animation appears on the display indicating
that the appliance is calculating the laundry
amount and the real duration. During this time,
the washing duration shown decreases.
Lock
Start/Pause
When the calculating phase has finished, the
arrows animation disappears from the display
and the washing time is adjusted to the real
load.
17
Smart 132973880.qxd
23/06/2008
12.22
Pagina
18
Operating sequence
Washing programme phase icons
By selecting the wash programme, the washing
programme phase icons corresponding to the
various phases making up the programme are
shown in the bottom of the display.
2.05
2.05
After the machine has started, only the running
icon stays on. When the programme has
finished, a flashing zero «0.00» is displayed.
Delayed start
The selected delay (20 hours max) set by
means of the relevant button appears on the
display for about 3 seconds, then the duration
of the previously selected programme is
displayed.
minute.
The delay time value
decreases by one unit
every hour and then,
when 1 hours remain,
the time decreases every
Alarm codes
In the event of
operating problems,
some alarm codes can
be displayed, for
example E20 (see
paragraph “Something not working”).
E20
Heating phase
During the washing
cycle the display shows
a temperature icon
illuminated to indicate
that the appliance has
started the heating phase of the water in the tub.
2.05
Child safety lock enabled
This device permits you to leave the appliance
unsupervised without having the worry that
children might be injured by or cause damage
to the appliance.
Easy Iron
Extra Rinse
Incorrect option selection
If an option which is not
compatible with the set
wash programme is
selected, the message
Err is displayed for about 2 seconds and the
integrated red Start/Pause light start flashing.
18
This function remains activated also when the
washing machine is not working.
There are two different ways to set this option:
● before pressing the Start/Pause: it will be
impossible to start the machine.
● after pressing the Start/Pause: it will be
impossible to change any other programme
or option.
To enable or disable this option press
simultaneously for about 6 seconds “Easy Iron”
and “Extra Rinse” buttons until the icon
appears or disappears from the display.
Smart 132973880.qxd
23/06/2008
12.22
Pagina
19
Operating sequence
10. Select the Start/Pause
To start the selected programme, press the
Start/Pause button; the corresponding green
pilot light stops flashing.
The «Lock» light
illuminates to indicate
that the appliance starts
operating and the door
is locked.
Lock
Start/Pause
The “Lock” light indicates if the door can be
opened:
● light on: the door cannot be opened.
The appliance is running.
● light off: the door can be opened.
The washing programme is finished.
To interrupt a programme which is running,
depress the Start/Pause button: the
corresponding green pilot light starts to flash.
To restart the programme from the point at
which it was interrupted, press the Start/Pause
button again.
If you have chosen a delayed start, the
machine will begin the countdown.
IMPORTANT!
If an incorrect option is selected, the red pilot
light of the Start/ Pause button flashes for 3
times and the message Err is displayed for
about 2 seconds.
11. Select the Delay Start
Delay Start
90’
Before you start the programme, if you wish to
delay the start, press repeatedly the «Delay
Start» buttons
and
, to select the
desired delay.
The selected delay time value (up to 20 hours)
will appear on the display for about 3 seconds,
then the duration of the programme will appear
again.
You must select this option after you have set
the programme and before you press the
Start/Pause button.
The wash programme can be delayed from 30
mins - 60 mins - 90 mins, 2 hours and then by
1 hour up to a maximum of 20 hours by means
of this button.
Selecting the delayed start:
● Select the programme and the required
options.
● Select the delay start.
● Depress “Start/Pause” button: the machine
starts its hourly countdown.
The programme will start after the selected
delay has expired.
Cancelling the delayed start:
You can cancel the delay time at any moment,
before you press the Start/Pause button.
If you have already pressed the Start/Pause
button, and you wish to cancel the delay time,
proceed as follows:
• set the washing machine to PAUSE by
pressing the Start/Pause button;
• press the Delay Start buttons once until the
symbol 0’ is displayed.
• press the Start/Pause button again to start
the programme.
19
Smart 132973880.qxd
23/06/2008
12.22
Pagina
IMPORTANT!
The door will be locked throughout the delay
time. If you need to open the door, you must
first set the washing machine to PAUSE by
pressing the Start/Pause button, wait until the
«Lock» pilot light goes off. After you have
closed the door, press the Start/Pause button
again.
Note!
The Delay Start cannot be selected with
Drain programme.
Altering an option or a running programme
It is possible to change any option before the
programme carries it out.
Before you make any change, you must pause
the washing machine by pressing the
Start/Pause button.
Changing a running programme is possible
only by resetting it. Turn the programme
selector dial to Off and then to the new
programme position. Start the new programme
by depressing the Start/Pause button again.
The washing water in the tub will not empty
out.
Interrupting a programme
Depress the Start/Pause button to interrupt a
programme which is running, the
corresponding light starts to flash. Depress the
button again to restart the programme.
Cancelling a programme
Turn the selector dial to Off to cancel a
programme which is running. Now you can
select a new programme.
20
20
Opening the door after the programme has
started
First set the machine to pause by pressing the
Start/Pause button.
If the «Lock» light goes off, the door can be
opened.
If the «Lock» light does not switch off, this
means that the machine is already heating,
that the water level is above the bottom edge
of the door or that the drum is turning.
In this case the door can not be opened.
If you cannot open the door but you need to
open it you have to switch the machine off by
turning the selector dial to «Off». After about 3
minutes the door can be opened (pay attention
to the water level and temperature!).
At the end of the programme
The machine stops automatically. The
Start/Pause light goes off, the «Lock» light
goes off and on the display will appear a
flashing «0.00». The door can be opened.
If the
«Rinse hold» or
«Night Cycle»
option has been selected, the «Lock» light
remains alight and the door is locked to
indicate that the water must be emptied out
before opening the door.
The display will show a flashing «0.00».
To empty out the water please read the steps
on the Rinse Hold option paragraph.
Turn the programme selector dial to «Off» to
switch the machine off.
Remove the laundry from the drum and
carefully check that the drum is empty.
If you do not intend to carry out another wash,
close the water tap. Leave the door open to
prevent the formation of mildew and
unpleasant smells.
Smart 132973880.qxd
23/06/2008
12.22
Pagina
21
Care and cleaning
IMPORTANT!
You must DISCONNECT the appliance from
the electricity supply, before you can carry out
any cleaning or maintenance work.
Remove the drawer by pressing the catch
downwards and by pulling it out. Flush it out
under a tap, to remove any traces of
accumulated powder.
Descaling
The water we use normally contains lime. It is
a good idea to periodically use a water
softening powder in the machine. Do this
separately from any laundry washing, and
according to the softening powder
manufacturer's instructions. This will help to
prevent the formation of lime deposits.
Cleaning the drawer recess
Maintenance Wash
With the use of low temperature washes it is
possible to get a build up of residues inside the
drum.
We recommend that a maintenance wash be
performed on a regular basis.
To run a maintenance wash:
● The drum should be empty of laundry.
● Select the hottest cotton wash programme.
● Use a normal measure of detergent, must be
a powder with biological properties.
External cleaning
Clean the exterior cabinet of the appliance with
soap and water only, and then dry thoroughly.
Cleaning the dispenser drawer
The washing powder and additive dispenser
drawer should be cleaned regularly.
Having removed the
drawer, use a small
brush to clean the
recess, ensuring that all
washing powder
residue is removed from
the upper and lower
part of the recess.
Replace the drawer and run the rinse
programme without any clothes in the drum.
Cleaning the pump
The pump should be inspected if
● the machine does not empty and/or spin
● the machine makes an unusual noise during
draining due to objects such as safety pins,
coins etc. blocking the pump.
Proceed as follows:
● Disconnect the appliance.
● If necessary wait until the water has cooled
down.
● Open the pump door.
●
To aid cleaning, the top part of the additive
compartment should be removed.
Place a container close
to the pump to collect
any spillage.
● Pull out the emergency
emptying hose, place it
in the container and
remove its cap.
When no more water comes out, unscrew the
pump cover and remove it. Always keep a
rag nearby to dry up spillage of water when
removing the cover.
●
21
Smart 132973880.qxd
●
●
23/06/2008
12.22
Pagina
Remove any objects from the pump impeller
by rotating it.
Refit the cap on the emergency emptying
hose and place the latter back in its seat.
Screw the pump cover
fully in.
● Close the pump door.
●
IMPORTANT!
When the appliance is in use and depending
on the programme selected there can be hot
water in the pump.
Never remove the pump cover during a wash
cycle, always wait until the appliance has
finished the cycle, and is empty. When
replacing the cover, ensure it is securely
retightened so as to stop leaks and young
children being able to remove it.
Cleaning the water inlet filter.
If your water is very hard or contains traces of
lime deposit, the water inlet filter may become
clogged.
It is therefore a good idea to clean it from time
to time.
Turn off the water tap.
Unscrew the water inlet
hose. Clean the filter
using a hard bristle
brush. Tighten up the
inlet hose.
22
22
The dangers of freezing
If the machine is exposed to temperatures
below 0°C, certain precautions should be
taken.
● Turn off the water tap.
● Unscrew the inlet hose.
● Place the end of the emergency emptying
hose and that of the inlet hose in a bowl
placed on the floor and let water drain out.
● Screw the water inlet hose back on and
reposition the emergency emptying hose
after having put the cap on again.
● When you intend to start the machine up
again, make sure that the room temperature
is above 0°C.
Emergency emptying out
If the water is not discharged, proceed as
follows to empty out the machine:
● pull out the plug from the power socket;
● close the water tap;
● if necessary, wait until the water has cooled
down;
● open the pump door;
● place a bowl on the floor and place the end
of the emergency emptying hose into the
bowl. Remove its cap. The water should
drain by gravity into the bowl. When the bowl
is full, put the cap back on the hose. Empty
the bowl. Repeat the procedure until water
stops flowing out;
● clean the pump if necessary as previously
described;
● replace the emergency emptying hose in its
seat after having plugged it;
● Replace the pump cover and close the door.
Smart 132973880.qxd
23/06/2008
12.22
Pagina
23
Something not working
IMPORTANT!
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily
without calling out an engineer. Before contacting your local Service Centre, please carry out the
checks listed below.
During machine operation it is possible that the red Start/Pause pilot light flashes,one of the
following alarm codes appears on the display and 3 acoustic signals sound every 20 seconds to
indicate that the machine is not working.
● E10: problem with the water supply
● E20: problem with water draining
● E40: door open.
Once the problem has been eliminated, press the Start/Pause button to restart the programme. If
after all checks, the problem persists, contact your local Service Centre.
Malfunction
Possible Cause / Solution
The washing machine does not start:
The door has not been closed. E40
• Close the door firmly.
The plug is not correctly inserted in the power socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical installation.
The main fuse has blown.
• Replace the fuse.
The selector dial is not correctly positioned and the
Start/Pause button has not been depressed.
• Please turn the selector dial and press the
Start/Pause button again.
The delay start has been selected.
• If the laundry is to be washed immediately, cancel
the delay start
The machine does not fill:
The water tap is closed. E10
• Open the water tap.
The inlet hose is squashed or kinked. E10
• Check the inlet hose connection.
The filter in the inlet hose is blocked. E10
• Clean the water inlet hose filter.
The door is not properly closed. E40
• Close the door firmly.
23
Smart 132973880.qxd
23/06/2008
12.22
Malfunction
The machine fills then empties
immediately:
The machine does not empty and/or
does not spin:
Pagina
24
Possible Cause / Solution
The end of the drain hose is too low.
• Refer to relevant paragraph in «water drainage»
section.
The drain hose is squashed or kinked. E20)
• Check the drain hose connection.
The drain pump is clogged. E20
• Clean the drain pump.
The option
or
has been selected.
• Select the Drain or Spin programmes
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
Too much detergent or unsuitable detergent (creates
too much foam) has been used.
• Reduce the detergent quantity or use another one.
There is water on the floor:
Check whether there are any leaks from one of the
inlet hose fittings. It is not always easy to see this as
the water runs down the hose; check to see if it is
damp.
• Check the water inlet hose connection.
The inlet hose or the drain is damaged.
• Replace it with a new one.
The cap on the emergency emptying hose has not
been refitted after cleaning the pump.
• Refit the cap on the emergency emptying hose
and place the latter back in its seat.
Unsatisfactory washing results:
24
Too little detergent or unsuitable detergent has been
used.
• Increase the detergent quantity or use another one.
Stubborn stains have not been treated prior to
washing.
• Use commercial products to treat the stubborn
stains.
The correct temperature was not selected.
• Check if you have selected the correct
temperature.
Excessive laundry load.
• Reduce the amount of laundry.
Smart 132973880.qxd
23/06/2008
12.22
Pagina
Malfunction
25
Possible Cause / Solution
...
...
No.
..
Ser.
Mod.
Prod ...
. No. ... ...
...
...
If you are unable to identify or solve the
problem, contact our service centre.
Before telephoning, make a note of the model,
serial number and purchase date of your
machine: the Service Centre will require this
information.
...
The programme is still running.
• Wait until the end of washing cycle.
The door lock has not been released.
The door will not open:
• Wait until the «Lock» light has gone out.
There is water in the drum.
• Select drain or spin programme to empty out the
water.
The transit bolts and packing have not been
removed.
• Check the correct installation of the appliance.
The support feet have not been adjusted.
• Check the correct levelling of the appliance.
The machine vibrates or is noisy:
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
There may not be enough laundry in the drum.
• Load more laundry.
The electronic unbalance detection device has cut in
because the laundry is not evenly distributed in the
drum. The laundry is redistributed by reverse rotation
of the drum. This may happen several times before
the unbalance disappears and normal spinning can
Spinning starts late or the machine
does not spin:
resume. If, after 10 minutes, the laundry is still not
evenly distributed in the drum, the machine will not
spin. In this case, redistribute the load manually and
select the spin programme.
● Redistribute the laundry.
The machine is fitted with a type of motor which
makes an unusual noise compared with other
motors. This new motor ensures a softer
The machine makes an unusual noise traditional
start and more even distribution of the laundry in the
drum when spinning, as well as increased stability of
the machine.
Machines based on modern technology operate very
No water is visible in the drum
economically using very little water without affecting
performance.
Mod. ... ... ...
Prod. No. ... ... ...
Ser. No. ... ... ...
25
Smart 132973880.qxd
23/06/2008
12.22
Pagina
26
Technical data
Dimensions
Width
60 cm
Height
85 cm
Depth (including the porthole)
63 cm
Electrical connection Voltage Overall power - Fuse
Information on the electrical connection is given on the rating
plate on the inner edge of the appliance door
Water supply pressure
Minimum
0,05 MPa
Maximum
0,8 MPa
Maximum Load
Cotton
Synthetics
Delicates
Woollens and handwash
Spin Speed
Maximum
7.0
3.5
3.5
2.0
0
kg
kg
kg
kg
1400 rpm
Consumption values
Programmes
Cotton 95°C - Proportional
Cotton 60° Eco(*) - Proportional
Synthetic 60°C - Proportional
Programme
duration
(in minutes)
Please refer
to the display
on the
control panel.
Energy
consumption
(in kWh)
Water
consumption
(in litres)
2.1
62
1.19
52
2.3
0.9
46
Information
The consumption data for the proportional programmes given on this chart is to be considered purely
indicative and refers to the highest load size for each wash programme.
26
Smart 132973880.qxd
23/06/2008
12.23
Pagina
27
Consumption values
Water
consumption
(in litres)
Cottons Normal 95°-
2.1
62
Cottons Prewash 95°C -
2.3
74
0.6
41
0.9
54
Synthetics Prewash 60°C -
1.05
64
Synthetics Superquick 60°C-
0.4
42
Delicates 40°C
0.55
63
Mini 30’
0.25
47
Duvet 30°C
0.35
75
Silk 30°C
0.25
50
Handwash 40°C -
0.4
58
Wool 40°C -
0.4
58
Sport Shoes 40°C
0.5
57
Sport 40°C
0.65
70
Cottons Superquick 95 Synthetics Normal 60°C -
Rinse
0.1
46
Drain
-
-
Spin
-
-
Information
The consumption data shown on this chart is to
be considered purely indicative, as it may vary
depending on the quantity and type of laundry,
on the inlet water temperature and on the
ambient temperature. It refers to the highest
temperature for each wash programme.
Programme
duration
For the duration of the programmes, please refer to the display on
the control panel.
Energy
consumption
(in kWh)
Programme
(*) The “Cotton 60° Eco” is the reference
programme for the data entered in the
energy label, in compliance with EEC 92/75
standards.
27
Smart 132973880.qxd
23/06/2008
12.23
Pagina
28
Installation instruction
Unpacking
All transit bolts and packing must be removed
before using the appliance.
You are advised to keep all transit devices so
that they can be refitted if the machine ever
has to be transported again.
1. After removing all the packaging, carefully
lay machine on it’s back to remove the
polystyrene base from the bottom.
2. Remove the power supply cable and the
draining hose from the hose holders on the
rear of the appliance.
A
C
B
C
B
3. With a suitable spanner unscrew and
remove the central rear bolt A.
4. Unscrew and remove the two large rear
bolts B and the six smaller bolts C.
E
C
D
C
28
5. Remove the bracket D, refit the six smaller
bolts C and slide out the relevant plastic
spacer E.
6. Open the porthole, take out the inlet hose
from the drum and remove the polystyrene
block fitted on the door seal.
7. Fill the smaller upper hole and the two large
ones with the corresponding plastic plug
caps supplied in the bag containing the
instruction booklet.
Positioning
Install the machine on a flat hard floor. Make
sure that air circulation around the machine is
not impeded by carpets, rugs etc. Check that
the machine does not touch the wall or other
kitchen units. Level the washing machine by
raising or lowering the feet. The feet may be
tight to adjust as they incorporate a self locking
nut, but the machine MUST be level and
stable.
If necessary, check the setting with a spirit
level.
Any necessary adjustment can be made with a
spanner.
Accurate levelling prevents vibration, noise and
displacement of the machine during
operation.Never place cardboard, wood or
similar materials under the machine to
compensate for any unevenness in the floor.
23/06/2008
12.23
Pagina
Water inlet
An inlet hose is supplied and can been found
inside the machine drum.
Do not use the hose from your previous
machine to connect to the water supply.
1. Open the porthole and extract the inlet
hose.
2. Connect the hose with the angled
connection to the machine.
Do not place the inlet hose downwards.
Angle the hose to the left or right depending
on the position of your water tap.
The appliance must be connected to a cold
water supply.
A minimum water pressure of 0.05 MPa (0.5
bar) is required for safe operation of the
appliance.
If you cannot make the cold water connection
direct from the rising mains, you may be able
to operate the appliance from your cold water
storage system.
There should be a minimum vertical distance
of 5.02m (16.5 ft) between the appliance’s
inlet and the bottom of the water storage tank.
Water drainage
This appliance is designed to be permanently
plumbed into your home's drainage system
using one of the following methods.
1. Into a drainage standpipe.
“U” piece
supplied
45°
35°
3. Set the hose
correctly by loosening
the ring nut.
After positioning the
inlet hose, be sure to
tighten the ring nut
again to prevent leaks.
4. Connect the hose to a tap with a 3/4” thread.
Always use the hose supplied with the
appliance. The inlet hose must not be
lengthened. If it is too short and you do not
wish to move the tap, you will have to
purchase a new, longer hose specially
designed for this type of use.
29
NOTE
Installation should
comply with local
water authority and
building regulations’
requirements.
Special
Sport 40°
Sport Shoes 40°
Off
Cottons
95°
60° Eco
Silk
60°
Mini 30'
1000 6kg
40° Eco
Cold
Hand
Wash
30°
3h
40°
9h
900
700
Wash
Prewash
Door
Intensive
End
Super
Quick
Spin
Options
Extra Rinse
Start/Pause
Easy Iron 40°
Spin
Drain
6h
1000
40°
Synthetics
50°
Wool
Rinse
30°
40°
Delicates
ZWF10070W
38 mm (1.5”)
standpipe
diameter
30 cm (12")
Smart 132973880.qxd
Firstly form a hook in the end of the drain
hose using the «U» piece supplied. Place the
drain hose into your standpipe, which should
have an internal diameter of approximately
38mm thus ensuring there is an air break
between the drain hose and standpipe.
When discharging into a standpipe ensure that
the top of the standpipe is no more than 90
cm (35.4'') and no less than 60 cm (23.6'')
above floor level.
29
Smart 132973880.qxd
Sport 40°
Sport Shoes 40°
Off
Cottons
95°
60° Eco
Silk
60°
Mini 30'
40° Eco
Cold
Hand
Wash
30°
40°
3h
6h
9h
900
700
Wash
Prewash
Door
Intensive
End
Super
Quick
Spin
Options
Extra Rinse
Start/Pause
Easy Iron 40°
Spin
Rinse
30°
40°
Delicates
ZWF10070W
Min. 60 cm (23.6”)
Drain
Pagina
1000
40°
Synthetics
50°
Wool
12.23
Max. 90 cm (35.4”)
Special
1000 6kg
23/06/2008
The drain hose may be extended to a
maximum of 4 metres. An additional drain hose
and joining piece is available from your local
Service Force Centre. The joining piece must
have an internal diameter of 18mm.
If your drain hose
looks like this (see
below) you do not
require the «U» piece.
Just push the hose
firmly into the
standpipe.
2. Onto a sink outlet spigot.
If the outlet spigot has not been used before,
remove any blanking plug that may be in place.
Loop
Push the drain hose onto the spigot and secure
with a clip if required, ensure a loop is formed
in the drain hose (see diagram) to prevent
waste from the sink entering the washing
machine.
Important!
Before connecting the machine to new
pipework or to pipework that has not been
used for some time, run off a reasonable
amount of water to flush out any debris that
may have collected in the pipes.
30
30
Levelling
Level the washing machine by raising or
lowering the feet. The feet may be tight to
adjust as they incorporate a self locking nut,
but the machine MUST be level and stable.
Any necessary
adjustment can be
made with a spanner.
Accurate levelling
prevents vibration,
noise and
displacement of the
machine during operation.
Some vibration is inevitable, especially if
mounted on a wooden floor.
Sprung wooden floors are particularly
susceptible to vibration. For advice, consult a
builder. If possible, always place the machine
on a solid floor.
Special conditions
If the floor is carpeted or covered with crumbly
or soft material, insert a rigid support base
under the feet to prevent noise, vibration or
displacement. The base should protrude a few
centimetres beyond the edges of the machine.
WARNING!
The machine should NOT be placed on deep
pile carpeting.
NOTE
Please ensure that when the appliance is
installed it is easily accessible for the engineer
in the event of a breakdown.
In the interest of the environment
Washing machines and dishwashers should be
connected to the FOUL drainage system, the
water will then be taken to a sewage works for
treatment before being discharged safely into a
river. It is essential that these appliances are
not connected to the surface water drainage
system as this water is discharged directly into
a river or stream and may cause pollution.
Smart 132973880.qxd
23/06/2008
12.23
Pagina
If you require any further advice please
contact your local water authority.
SHOWER
31
The wires in the mains lead are coloured in
accordance with the following code:
Green and Yellow ..............................- Earth
Blue ....................................................- Neutral
Brown..................................................- Live
The wire coloured green
GREEN & YELLOW
and yellow must be
connected to the
terminal marked with
the letter «E» or by the
or
BROWN earth symbol
coloured green and
BLUE
CORD CLAMP
yellow.
The wire coloured blue must be connected to
the terminal marked «N» or coloured black.
The wire coloured brown must be connected to
the terminal marked «L» or coloured red.
Upon completion there must be no cut, or stray
strands of wire present and the cord clamp
must be secure over the outer sheath.
TOILET
BIDET
13 A
E
SINK
BATH
N
WASHING
MACHINE
DISHWASHER
RAINWATER
'RUN-OFF'
FOUL DRAIN
SURFACE WATER
DRAINS & SEWERS
UNTREATED
DISCHARGE
FOUL SEWERS
SEWAGE
TREATMENT
WORKS
TREATED
DISCHARGE
RIVER
RIVER
Electrical connection
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
WARNING!
This appliance must be earthed.
The manufacturer declines any liability
should this safety measure not be
observed.
Before switching on, make sure the electricity
supply voltage is the same as that indicated
on the appliance’s rating plate.
IMPORTANT!
Information on the electrical connection is
given on the rating plate on the inner edge
of the appliance door.
The appliance is supplied with a 13amp plug
fitted. In the event of having to change the
fuse in the plug supplied, a 13amp ASTA
approved (BS1363/A) fuse must be used.
Should the plug need to be replaced for any
reason, proceed as described below.
L
WARNING!
A cut off plug inserted into a 13 amp socket
is a serious safety (shock) hazard.
Ensure that the cut off plug is disposed of
safely. Should the appliance power supply
cable need to be replaced, this must be
carried out by our Service Force Centre.
The power supply cable must be easily
accessible after installing the appliance.
Permanent connection
In the case of permanent connection it is
necessary that you install a double pole switch
between the appliance and the electricity
supply (mains), with a minimum gap of 3mm
between the switch contacts and of a type
suitable for the required load in compliance
with the current electrical regulations.
The switch must not break the yellow and
green earth cable at any point.
31
Smart 132973880.qxd
23/06/2008
12.23
Pagina
32
Environmental concerns
Packaging materials
The materials marked with the symbol
are
recyclable.
>PE<=polyethylene
>PS<=polystyrene
>PP<=polypropylene
This means that they can be recycled by
disposing of them properly in appropriate
collection containers.
Old machine
Use authorised disposal sites for your old
appliance. Help to keep your country tidy!
The symbol
on the product or on its
packaging indicates that this product may not
be treated as household waste. Instead it
should be taken to the appropriate collection
point for the recycling of electrical and
electronic equipment. By ensuring this product
is disposed of correctly, you will help prevent
potential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste
handling of this product. For more detailed
information about recycling of this product,
please contact your local council, your
household waste disposal service or the shop
where you purchased the product.
32
Ecological hints
To save water, energy and to help protect the
environment, we recommend that you follow
these tips:
● Normally soiled laundry may be washed
without prewashing in order to save
detergent, water and time (the environment
is protected too!).
● The machine works more economically if it is
fully loaded.
● With adequate pre-treatment, stains and
limited soiling can be removed; the laundry
can then be washed at a lower temperature.
● Measure out detergent according to the
water hardness, the degree of soiling and
the quantity of laundry being washed.
Smart 132973880.qxd
23/06/2008
12.23
Pagina
33
Guarantee conditions
Standard guarantee conditions
We, Zanussi-Electrolux, undertake that if
within12 months of the date of the purchase
this Zanussi-Electrolux appliance or any part
thereof is proved to be defective by reason
only of faulty workmanship or materials, we
will, at our option repair or replace the same
FREE OF CHARGE for labour, materials or
carriage on condition that:
● The appliance has been correctly installed
and used only on the electricity supply stated
on the rating plate.
● The appliance has been used for normal
domestic purposes only, and in accordance
with the manufacturer's instructions.
● The appliance has not been serviced,
maintained, repaired, taken apart or
tampered with by any person not authorised
by us.
● Electrolux Service Force Centre must
undertake all service work under this
guarantee.
● Any appliance or defective part replaced
shall become the Company's property.
● This guarantee is in addition to your
statutoryand other legal rights.
Exclusions
● Damage or calls resulting from
transportation, improper use or neglect, the
replacement of any light bulbs or removable
parts of glass or plastic.
● Costs incurred for calls to put right an
appliance which is improperly installed or
calls to appliances outside the United
Kingdom.
● Appliances found to be in use within a
commercial environment, plus those which
are subject to rental agreements.
● Products of Electrolux manufacturer that are
not marketed by Electrolux.
Service and Spare Parts.
In the event of your appliance requiring
service, or if you wish to purchase spare parts,
please contact your local Service Force Centre
by telephoning:
0870 5 929 929
Your telephone call will be automatically routed
to the Service Force Centre covering your
postcode area. For the address of your local
Service Force Centre and further information
about Service Force, please visit the website at
www.serviceforce.co.uk
Before calling out an engineer, please ensure
you have read the details under the heading
«Something not working». When you contact
the Service Force Centre you will need to give
the following details:
1
2
3
4
Your name, address and postcode.
Your telephone number.
Clear concise details of the fault.
The model and Serial number of the
appliance (found on the rating plate).
5 The purchase date.
Please note a valid purchase receipt or
guarantee documentation is required for in
guarantee service calls.
Customer Care
For general enquiries concerning your ZanussiElectrolux appliance, or for further information
on Electrolux products please contact our
Customer Care Department by letter or
telephone at the address below or visit our
website at www.zanussi-electrolux.co.uk
Customer Care Department Electrolux Major
Appliances Addington Way Luton Bedfordshire,
LU4 9QQ Tel: 08705 727 727 (*)
(*) Calls may be recorded for training purposes
33
Smart 132973880.qxd
23/06/2008
12.23
Pagina
For Customer Service in The Republic of
Ireland please contact us at the address below:
Electrolux Group (Irl) Ltd
Long Mile Road, Dublin 12, Republic of Ireland
Tel: + 353 (0)1 4090751
Email: service.eid@electrolux.ie
European guarantee
This appliance is guaranteed by Electrolux, in
each of the countries listed in the following
page, for the period specified in the appliance
guarantee or otherwise by law. If you move
from one of these countries to another of these
countries the appliance guarantee will move
with you subject to the following qualifications:
●
●
●
●
●
The appliance guarantee starts from the
date you first purchased the appliance
which will be evidenced by production of a
valid purchase document issued by seller
of the appliance.
The appliance guarantee is for the same
period and to the same extent for labour
and parts as exists in your country of
residence for this particular model or range
of appliances.
The appliance guarantee is personal to the
original purchaser of the appliance and
cannot be transferred to another user.
The appliance is installed and used in
accordance with instructions issued by
Electrolux and is only used within the
home, i.e. is not used for commercial
purposes.
The appliance is installed in accordance
with all relevant regulations in force within
your new country of residence.
The provisions of this European Guarantee do
not affect any of the rights granted to you by
law.
34
34
Smart 132973880.qxd
23/06/2008
12.23
Pagina
35
www.electrolux.com
à
Albania
+35 5 4 261 450
Rr. Pjeter Bogdani Nr. 7 Tirane
Belgique/België/Belgien
+32 2 363 04 44
Bergensesteenweg 719, 1502 Lembeek
Česká republika
+420 2 61 12 61 12
Budějovická 3, Praha 4, 140 21
Danmark
+45 70 11 74 00
Sjællandsgade 2, 7000 Fredericia
Deutschland
+49 180 32 26 622
Muggenhofer Str. 135, 90429 Nürnberg
Eesti
+37 2 66 50 030
Mustamäe tee 24, 10621 Tallinn
España
+34 902 11 63 88
Carretera M-300, Km. 29,900 Alcalá de Henares Madrid
France
www.electrolux.fr
Great Britain
+44 8705 929 929
Addington Way, Luton, Bedfordshire LU4 9QQ
Hellas
+30 23 10 56 19 70
4, Limnou Str., 54627 Thessaloniki
Hrvatska
+38 51 63 23 338
Slavonska avenija 3, 10000 Zagreb
Ireland
+353 1 40 90 753
Longmile Road Dublin 12
Italia
+39 (0) 434 558500
C.so Lino Zanussi, 26 - 33080 Porcia (PN)
Latvija
+37 17 84 59 34
Kr. Barona iela 130/2, LV-1012, Riga
Lituania
+370 5 27 80 609
Verkiu,2 9, 09108 Vilnius, Lithuania
Luxembourg
+35 2 42 43 13 01
Rue de Bitbourg, 7, L-1273 Hamm
Magyarország
+36 1 252 1773
H-1142 Budapest XIV, Erzsébet királyné útja 87
Nederland
+31 17 24 68 300
Vennootsweg 1, 2404 CG - Alphen aan den Rijn
Norge
+47 81 5 30 222
Risløkkvn. 2 , 0508 Oslo
Österreich
+43 18 66 400
Herziggasse 9, 1230 Wien
Polska
+48 22 43 47 300
ul. Kolejowa 5/7, Warsaw
Portugal
+35 12 14 40 39 39
Quinta da Fonte - Edificio Gonçalves Zarco - Q35 -2774-518 Paço de Arcos
Romania
+40 21 451 20 30
Str. Garii Progresului 2, S4, 040671 RO
Schweiz-Suisse-Svizzera
+41 62 88 99 111
Industriestrasse 10, CH-5506 Mägenwil
Slovenija
+38 61 24 25 731
Tr aška 132, 1000 Ljubljana
Slovensko
+421 2 43 33 43 22
Electrolux Slovakia s.r.o., Electrolux Domáce spotrebiče SK, Seberíniho 1, 821 03 Bratislava
Suomi
www.electrolux.fi
Sverige
+46 (0)771 76 76 76
Electrolux Service, S:t Göransgatan 143, S-105 45 Stockholm
Türkiye
+90 21 22 93 10 25
Tarlabași caddesi no : 35 Taksim Istanbul
Россия
+7 095 937 7837
129090 Москва, Олимпийский проспект, 16, БЦ “Олимпик”
35
Smart 132973880.qxd
23/06/2008
12.23
Pagina
36
www.electrolux.com
www.zanussi-electrolux.co.uk
132973880
Subject to change without notice