Philips BDL4220QL User's Manual

BDL4220QL
www.philips.com/welcome
User Manual (English)
BDL4220QL
Safety Instructions
TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR ELECTRIC
SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN
OR MOISTURE.
Warnings and Precautions
The Socket-outlet should be installed near the apparatus and be easily
accessible.
KNOW THESE SAFETY SYMBOLS
Read and follow these instructions
when connecting and using your Public
Information Display:
• Unplug the display if you are not going to use it for an extensive
period of time.
• Unplug the display if you need to clean it with a slightly damp cloth.
The screen many be wiped with a dry cloth when the power is off.
However, never use alcohol, solvents or ammonia-based liquids.
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
• Consult a service technician if the display does not operate normally
when you have followed the instructions in this manual.
• The casing cover should be opened only by qualified service
personnel.
This symbol indicates high voltage is present inside.
It is dangerous to make any kind of contact with any
inside part of this product.
• Keep the display out of direct sunlight and away from stoves or any
other heat sources.
• Remove any object that could fall into the vents or prevent proper
cooling of the display’s electronics.
This symbol alerts you that important literature
concerning operation and maintenance has been
included with this product.
• Do not block the ventilation holes on the cabinet.
• Keep the display dry. To avoid electric shock, do not expose it to
rain or excessive moisture.
CAUTION:FCC/CSA regulations state that any unauthorized
changes or modifications to this equipment may void
the user’s authority to operate it.
• If turning off the display by detaching the power cable, wait for 6
seconds before re-attaching the power cable for normal operation.
• To avoid the risk of shock or permanent damage to the set do not
expose the display to rain or excessive moisture.
CAUTION:To prevent electric shock, match the wide blade of plug
to the wide slot, and fully insert the plug.
• When positioning the display, make sure the power plug and outlet
are easily accessible.
• IMPORTANT: Always activate a screen saver program during your
application. If a still image in high contrast remains on the screen for
an extended period of time, it may leave an ‘after-image’ or ‘ghost
image’ on the front of the screen. This is a well-known phenomenon
that is caused by the shortcomings inherent in LCD technology. In
most cases the afterimage will disappear gradually over a period
of time after the power has been switched off. Be aware that the
after-image symptom cannot be repaired and is not covered under
warranty.
ii
BDL4220QL
Important Safety Instructions
CAUTION:These servicing instructions are for use by qualified
service personnel only. To reduce the risk of electric
shock,do not perform any servicing other than that
contained in the operating instructions unless you are
qualitified to do so.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
CAUTION:Excessive sound pressure from earphones and
headphones can cause hearing loss. Adjustment of the
equalizer to maximum increases the earphone and
headphone output voltage and the sound pressure level.
Therefore, to protect your hearing, adjust the equalizer
to an appropriate level.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
For UL/CUL application: For use only with UL Listed Wall Mount
Bracket with minimum weight/load: 35.7 kg.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
9. Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the
other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
For CB application: Unit without base weight: 11.9 kg. The equipment
and its associated mounting means still remain secure during the test.
(Used wall mounting kit: 400 x 400 mm distance by using M6 screws of
20 mm long plus the thickness of the mounting bracket.)
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for
long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
WARNING:TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPARATUS TO
RAIN OR MOISTURE.
WARNING:Apparatus shall not be exposed to dripping or splashing
and no objects filled with liquids, such as vases, shall be
placed on the apparatus.
WARNING:The batteries (batteries installed) shall not be exposed
to excessive heat such as sunshine, fire or the like.
WARNING:The mains plug or appliance coupler is used as the
disconnect device,the disconnect device shall remain
readily operable.
WARNING:To prevent the spread of fire, keep candles or other
open flames away from this product at all times.
WARNING:To prevent injury, this apparatus must be securely
attached to the floor/wall in accordance with the
installation instructions.
iii
BDL4220QL
Regulatory Information
Federal Communications Commission (FCC)
Notice (U.S. Only)
CE Declaration of Conformity
• EN61000-3-3:2008 (Limitation of Voltage Fluctuation and Flicker)
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses and can radiate radio frequency energy and,
if not installed and used in accordance with the
instructions manual, may cause harmful interference to
radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference
in which case the user will be required to correct the
interference at his own expense.
• EN 50581:2012 (Technical documentation for the assessment of
electrical and electronic products with respect to the restriction of
hazardous substances)
Changes or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.
We declare under our responsibility that the product is in conformity
with the following standards:
• EN60065:2002+A1:2006+A11:2008+A2:2010+A12:2011 (Safety
requirement of Audio, video and similar electronic apparatus)
• EN55022:2010 (Radio Disturbance requirement of Information
Technology Equipment)
• EN55024:2010 (Immunity requirement of Information Technology
Equipment)
• EN61000-3-2:2006 +A1:2009+A2:2009 (Limits for Harmonic
Current Emission)
following provisions of directives applicable:
Use only an RF shielded cable that was supplied with the display when
connecting this display to a computer device.
• 2006/95/EC (Low Voltage Directive)
• 2004/108/EC (EMC Directive)
To prevent damage which may result in fire or shock hazard, do not
expose this appliance to rain or excessive moisture.
• 2009/125/EC (ErP Directive, EC No. 1275/2008, 642/2009
Implementing Directive for Standby and Off mode power
consumption)
THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS
OF THE CANADIAN INTERFERENCE- CAUSING EQUIPMENT
REGULATIONS.
• 93/68/EEC (Amendment of EMC and Low Voltage Directive) and is
produced by a manufacturing organization on ISO9000 level.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
• 2011/65/EU (RoHS 2 Directive)
iv
BDL4220QL
Polish Center for Testing and Certification
Notice
Information for U.K. only
WARNING – THIS APPLIANCE MUST BE EARTHED.
The equipment should draw power from a socket with an attached
protection circuit (a three-prong socket). All equipment that works
together (computer, display, printer, and so on) should have the same
power supply source.
Important:
(B)
The phasing conductor of the room’s electrical installation should have
a reserve short-circuit protection device in the form of a fuse with a
nominal value no larger than 16 amperes (A).
(A)
To completely switch off the equipment, the power supply cable must
be removed from the power supply socket, which should be located
near the equipment and easily accessible.
A protection mark “B” confirms that the equipment is in compliance
with the protection usage requirements of standards PN-93/T-42107
and PN-89/E-06251.
This apparatus is supplied with an approved moulded 13A plug. To
change a fuse in this type of plug proceed as follows:
1. Remove fuse cover and fuse.
2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved
type.
3. Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it should be cut
off and an appropriate 3-pin plug fitted in its place.
If the mains plug contains a fuse, this should have a value of 5A. If a plug
without a fuse is used, the fuse at the distribution board should not be
greater than 5A.
NOTE:The severed plug must be destroyed to avoid a possible shock
hazard should it be inserted into a 13A socket elsewhere.
How to connect a plug
Electric, Magnetic and Electronmagnetic
Fields (“EMF”)
1. We manufacture and sell many products targeted at consumers,
which, like any electronic apparatus, in general have the ability to
emit and receive electromagnetic signals.
2. One of our leading Business Principles is to take all necessary health
and safety measures for our products, to comply with all applicable
legal requirements and to stay well within the EMF standards
applicable at the time of producing the products.
The wires in the mains lead are coloured in accordance with the
following code:
BLUE – “NEUTRAL” (“N”)
BROWN – “LIVE” (“L”)
3. We are committed to develop, produce and market products that
cause no adverse health effects.
GREEN & YELLOW – “EARTH” (“E”)
4. We confirm that if its products are handled properly for their
intended use, they are safe to use according to scientific evidence
available today.
1. The GREEN & YELLOW wire must be connected to the terminal in
the plug which is marked with the letter “E” or by the Earth symbol
or coloured GREEN or GREEN & YELLOW.
5. We play an active role in the development of international EMF and
safety standards, enabling us to anticipate further developments in
standardization for early integration in its products.
2. The BLUE wire must be connected to the terminal which is marked
with the letter “N” or coloured BLACK.
3. The BROWN wire must be connected to the terminal which
marked with the letter “L” or coloured RED.
Before replacing the plug cover, make certain that the cord grip is
clamped over the sheath of the lead – not simply over the three wires.
v
BDL4220QL
China RoHS
中国电子信息产品污染控制标识要求
仅适用于非热带气候条件下安全使用 :
本产品有毒有害物质或元素的名称及含量标识表:
汉
有毒有害物质或元素
零部件名称
铅
汞
镉
六价铬 多溴联苯 多溴二苯醚
(Pb) (Hg) (Cd) (Cr 6+)
(PBBs)
(PBDEs)
塑料外框
O
O
O
O
O
O
后壳
O
O
O
O
O
O
CCFL
X
X
O
O
O
O
LCD
面板 LED
X
O
O
O
O
O
电源基板
X
O
O
O
O
O
主基板
X
O
O
O
O
O
按键基板
X
O
O
O
O
O
底座
O
O
O
O
O
O
电源线
X
O
O
O
O
O
其他线材
X
O
O
O
O
O
遥控器
X
O
O
O
O
O
*:电路板组件包括印刷电路板及其构成的零部件,如电阻、电容、
集成电路、连接器等。
○:表示该有害物质在该部件所有均质材料中的含量均在SJ/
T11363-2006《电子信息产品中有毒有害物质的限量要求》规定的
限量要求以下。
蒙古文
文 仅适用于非热带气候条件下安全使用。
藏
文
维
文
壮
文
Dan hab yungh youq gij dienheiq diuzgen mbouj dwg
diegndat haenx ancienz sawjyungh.
≤2000m 仅适用于海拔 2000m 以下地区安全使用 :
汉
文 仅适用于海拔 2000m 以下地区安全使用。
蒙古文
藏
文
维
文
壮
文 Hai dou gaxgonq, wngdang sien duenh denvasen bae.
×:表示该有害物质至少在该部件的某一均质材料中的含量超出
SJ/T11363-2006《电子信息产品中有毒有害物质的限量要求》规定
的限量要求;
汉
“注意
文 如果电池更换不当会有爆炸危险
只能用同样类型或等效类型的电池来更换”
备注:以上“×”的部件,部分含有有害物质超过是由于目前行业
技术水平所限,暂时无法实现替代或减量化。
蒙古文
10
藏
文
维
文
壮
“Louzsim
Danghnaeuz denyouz vuenh ndaej mbouj habdangq aiq miz
文 gij yungyiemj fatseng bauqcaq
Cijndaej yungh gij denyouz doengzyiengh loihhingz roxnaeuz
daengjyauq loihl haenx vuenh”
《废弃电子产品回收处理管理条例》提示性说明
汉
文
为了更好地关爱及保护地球,当用户不再需要此产品或产品寿命
终止时,请遵守国家废弃电器电子产品回收处理相关法律规定,
将其交给当地具有国家认可的回收处理资质的厂商进行回收处
理。
蒙古文
环保使用期限
在产品本体上标示的该标志表示环境保护使用期限为 10 年。
电子信息产品的环境保护使用期限是指电子信息产品中所含的有
毒有害物质或元素不会向外部泄漏或出现突然变异,并且电子信
息产品的用户在使用该电子信息产品时也不会对环境造成严重污
染或对人体、财产带来严重损害的期限。
在环境保护期限中,请按照使用说明书使用本产品。
本环境保护使用不覆盖易损件:电池。
vi
“接入本设备的有线网络天线必须与保护接地隔离 , 不
然可能会引起着火等危险 !”
藏
文
维
文
壮
“Gij mizsienq vangjloz denhsen ciephaeuj bonj sezbi daeuj
文 haenx itdingh aeu caeuq gij ciepdieg baujhoh doxliz, mboujne
aiq miz gij yungyiemj dawzfeiz daengj!”
BDL4220QL
North Europe (Nordic Countries)
Information
End-of-Life Disposal
Your new Public Information Display contains materials that can be
recycled and reused. Specialized companies can recycle your product to
increase the amount of reusable materials and to minimize the amount
to be disposed of.
Placering/Ventilation
VARNING:
Please find out about the local regulations on how to dispose of your
old display from your local Philips dealer.
FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG
ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING
PÅPLATS.
(For customers in Canada and U.S.A.)
This product may contain lead and/or mercury. Dispose of in accordance
to local-state and federal regulations. For additional information on
recycling contact www.eia.org (Consumer Education Initiative)
Placering/Ventilation
ADVARSEL:
Waste Electrical and Electronie EquipmentWEEE
SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG
STIKKONTAKT ER NEMT TILGÆNGELIGE.
Attention users in European Union private households
Paikka/Ilmankierto
This marking on the product or on its packaging
illustrates that, under European Directive 2002/96/
EC governing used electrical and electronic appliances,
this product may not be disposed of with normal
household waste. You are responsible for disposal of
this equipment through a designated waste electrical
and electronic equipment collection. To determine
the locations for dropping off such waste electrical
and electronic, contact your local government office,
the waste disposal organization that serves your
household or the store at which you purchased the
product.
VAROITUS:
SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN
TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA.
Plassering/Ventilasjon
ADVARSEL:
NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT
KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ.
End of Life Directives-Recycling
Your new Public Information Display contains several
materials that can be recycled for new users.
Like all LCD produces, this set contains a lamp with
Mercury. Please dispose of according to all Local, State,
and Federal laws.
As an ENERGY STAR Partner, we have determined
that this product meets the ENERGY STAR guidelines
for energy efficiency.
vii
BDL4220QL
Table Of Contents
1. Unpacking and Installation...................................... 1
1.1.Unpacking......................................................................1
1.2. Package Contents......................................................1
1.3. Installation Notes.......................................................1
1.4. Mounting on a Wall..................................................2
5.2.Settings.........................................................................13
5.2.1. Picture menu.............................................13
5.2.2. Sound menu..............................................14
5.2.3. General settings menu.........................15
5.3. Network Settings....................................................15
2. Parts and Functions.................................................. 3
2.1. Control Panel...............................................................3
2.2. Input/Output Terminals..........................................4
2.3. Remote Control.........................................................5
2.3.1. General functions......................................5
2.3.2. Inserting batteries in the remote
control.............................................................6
2.3.3. Handling the remote control..............6
2.3.4. Operating range of the remote
control.............................................................6
6. Input mode...............................................................16
3.Connection................................................................ 7
3.1. Connecting External Equipments.....................7
3.2. Connecting Multiple Displays.............................8
3.2.1. RS232C control connection
(optional)........................................................8
3.2.2. IR connection (optional).......................8
3.3. IR Pass-through Connection (optional)........8
3.4. Wire-connecting to Network (optional).......9
8.
7. Pixel Defect Policy..................................................17
7.1. Pixels and Sub-pixels.............................................17
7.2. Types of Pixel Defects + Dot Definition.. 17
7.3. Bright Dot Defects................................................17
7.4. Dark Dot Defects..................................................18
7.5. Proximity of Pixel Defects.................................18
7.6. Pixel Defect Tolerances.......................................18
7.7.MURA...........................................................................18
Cleaning and Troubleshooting..............................19
8.1.Cleaning.......................................................................19
8.2.Troubleshooting.......................................................20
9. Technical Specifications.........................................21
4.Operation.................................................................10
4.1. Watch the Connected Video Source..........10
4.2. Change Picture Format.......................................10
4.3. Select your Preferred Picture Settings........10
4.4. Select your Preferred Sound Settings.........10
4.5. Play Multimedia Files.............................................10
4.5.1. Play files from computer....................10
4.5.2. Play multimedia files from USB
device............................................................11
4.6. Play options................................................................11
4.6.1. Playing music files...................................11
4.6.2. Playing movie files..................................12
4.6.3. Playing photo files..................................12
5. Change your settings.............................................13
5.1. Quick Picture and Sound...................................13
viii
BDL4220QL
1.
Unpacking and Installation
1.1.
Unpacking
• This product is packed in a carton, together with the standard accessories.
• Any other optional accessories will be packed separately.
• Due to the size and weight of this display it is recommended for two people to move it.
• After opening the carton, ensure that the contents are complete and in good condition.
1.2.
Package Contents
Please verify that you received the following items with your package content:
• LCD display
• CD ROM
• Remote control with AAA batteries
• Power cord (1.8 m)
CD ROM
• VGA cable (1.8 m)
LCD Display
• RS232 cable (1.8 m)
LCD-Display / Pantalla LCD / Écran LCD / Display LCD /
Wyświetlacz LCD / ЖК-монитор / LCD Ekran / 监视器 / 監視器
BDL4220QL
• Quick start guide
Remote Control
and AAA Batteries
Kurzanleitung / Guía rápida / Guide de démarrage rapide / Guida rapida /
Instrukcja szybkiego uruchomienia / Краткое руководство по запуску /
Hızlı başlangiç kılavuzu / 快速入门指南 / 快速入門指南
Installation / Installation / Instalación / Installation / Installazione / Instalacja /
Установка / Kurulum / 安装 / 安裝
Connect / Verbindungsfähigkeit / Conectividad / Connectivité / Connettività /
Połączenia / Подключение / Bağlantı / 连接性 / 連接性
* The supplied power cord varies depending on destination.
Register your product and get support at
www.philips.com/welcome
Quick Start Guide
For EU
For China
RS232 Cable
For North America
VGA Cable
For UK
NOTES:
• For all other regions, apply a power cord that conforms to the AC voltage of the power socket and has been approved by and complies with the
safety regulations of the particular country.
• Keep the package box and packing material for shipping the display.
1.3.
Installation Notes
• Due to the high power consumption, always use the plug exclusively designed for this product. If an extended line is required, please consult your
service agent.
• The product should be installed on a flat surface to avoid tipping. The distance between the back of the product and the wall should be maintained
for proper ventilation. Avoid installing the product in the kitchen, bathroom or any other places with high humidity so as not to shorten the service life
of the electronic components.
• The product can normally operate only under 2000 m in altitude. In installations at altitudes above 2000 m, some abnormalities may be experienced.
1
BDL4220QL
1.4.
Mounting on a Wall
To mount this display to a wall, you will have to obtain a standard wall-mounting kit. We recommend using a mounting interface that complies with
UL1678 standard in North America.
400
Protective Sheet
400
Table
1. Lay a protective sheet on a table, which was wrapped around the display when it was packaged, beneath the screen surface so as not to scratch the
screen face.
2. Ensure you have all accessories for mounting this display.
3. Follow the instructions that come with the base mounting kit. Failure to follow correct mounting procedures could result in damage to the equipment
or injury to the user or installer. Product warranty does not cover damage caused by improper installation.
4. For the wall-mounting kit, use M6 mounting screws (20 mm long plus the thickness of the mounting bracket) and tighten them securely.
Caution:
To prevent the display from falling:
• To lessen the probability of injury and damage resulting from fall of the display in case of earthquake or other natural disaster, be sure to consult the
bracket manufacturer for installation location.
Ventilation Requirements for enclosure locating
To allow heat to disperse, leave space between surrounding objects as shown in the diagram below.
100 mm
100 mm
100 mm
100 mm
NOTE:When installing the display on a wall, please consult a professional technician for proper installation. We accept no liability for installations not
performed by a professional technician.
2
BDL4220QL
2.
Parts and Functions
2.1.
Control Panel
1
2
INPUT
3
MENU
4
5
6
8
7
1
[
] button
8
Press to switch the display on or off.
2
[
• Receives command signals from the remote control.
-- Lights green when this display is turned on
] button
-- Lights red when this display is in standby mode
Press to select input source.
3
[
-- Lights off when the main power of this display is turned off
] button
Press to access the OSD menu.
4
[ ] button
Press to move the highlight bar up to adjust the selected item while
OSD menu is on.
5
[ ] button
Press to move the highlight bar down to adjust the selected item
while OSD menu is on.
6
[ ] button
Press to increase the adjustment while OSD menu is on, or to
increase the audio output level while OSD menu is off.
7
Remote control sensor and power status indicator
[ ] button
Press to decrease the adjustment while OSD menu is on, or to
decrease the audio output level while OSD menu is off.
3
BDL4220QL
2.2.
Input/Output Terminals
IN
IN
14
13
OUT
2
15
OUT
16
12
11
R
10
9
R
L
1
L
8
Y
3
1
4
11 SPDIF
MAIN POWER SWITCH
12 IR
DVI IN
• To remotely control your A/V device via this display, refer to
page 8 for IR Pass Through connection.
RJ-45
14 RS232C
16 USB
VGA IN (D-Sub)
COMPONENT IN (RCA)
Component YPbPr video source input.
AUDIO IN (RCA)
Audio input from external AV device.
9
AUDIO OUT (RCA)
Audio signal output to connect your external AV device.
10 AUDIO
15
RS232C IN (2.5 mm)
PORT
Connect your UBS storage device.
VGA video input.
8
OUT /
RS232C network output/input for the loop-through function.
control center.
7
IR IN (3.5 mm)
• This display’s remote control sensor will stop working if the jack
[IR IN] is connected.
LAN control function for the use of remote control signal from
6
13
NOTES:
HDMI IN
DVI-D video input.
5
OUT /
IR signal output/input for the loop-through function.
HDMI video/audio input.
4
OUT
Digital audio signal output to connect your external AV device.
Main power on/off switch.
3
Pr
7
AC IN
AC power input.
2
6
5
Pb
IN (3.5mm)
Audio input from your PC.
4
BDL4220QL
2.3.
Remote Control
7
2.3.1. General functions
8
1
9
2
10 3
14
11 4
5
12 15
8
14 16
15 9
16 10
11
12
10
13
2
POWER button
Switch this display on or off.
PLAY buttons
Control playback of media files.
3
4
5
6
BACK button
Return to the previous menu page or exit from the previous
function.
VOLUME button
Adjust volume.
MUTE button
Press to turn the mute function on/off.
Select tasks or options.
COLOR buttons
buttons
Enter text for network setting.
7
ADJUST button
Access currently available options, picture and sound menus.
13 NUMERIC
6
1
button
Confirm an entry or selection.
SOURCE button
Select input source. Press [ ] or [ ] button to select from USB,
Network, HDMI, DVI, YPbPr, AV, or VGA. Press [
] button
to confirm and exit.
HOME button
Access the OSD menu.
LIST
No function.
NAVIGATION buttons
Navigate through menus and select items.
5
FORMAT button
Change picture format.
INFO button
Display information about current activity.
OPTIONS
Access currently available options, picture and sound menus.
BDL4220QL
2.3.2. Inserting batteries in the remote control
The remote control is powered by two 1.5V AAA batteries.
To install or replace batteries:
1. Press and then slide the cover to open it.
2. Align the batteries according to the (+) and (–) indications inside the
battery compartment.
3. Replace the cover.
Caution:
The incorrect use of batteries can result in leaks or bursting. Be sure to follow these instructions:
• Place “AAA” batteries matching the (+) and (–) signs on each battery to the (+) and (–) signs of the battery compartment.
• Do not mix battery types.
• Do not combine new batteries with used ones. It causes shorter life or leakage of batteries.
• Remove the dead batteries immediately to prevent them from liquid leaking in the battery compartment. Don’t touch exposed battery acid, as it can
damage your skin.
NOTE:If you do not intend to use the remote control for a long period, remove the batteries.
2.3.3. Handling the remote control
• Do not subject to strong shock.
• Do not allow water or other liquid to splash the remote control. If the remote control gets wet, wipe it dry immediately.
• Avoid exposure to heat and steam.
• Other than to install the batteries, do not open the remote control.
2.3.4. Operating range of the remote control
Point the front of the remote control toward this display’s remote control sensor when
pressing a button.
Use the remote control within a distance of less than 10m/33ft from this display’s sensor,
and a horizontal and vertical angle of less than 30 degrees.
NOTE:The remote control may not function properly when the remote control sensor
on this display is under direct sunlight or strong illumination, or when there is an
obstacle in the path of signal transmission.
30
6
30
BDL4220QL
3.
Connection
NOTE:The peripherals and cables shown are for example purposes only.
Connecting External Equipments
USB
PC
OUT
COMPONENT OUT (YPbPr)
AUDIO OUT
AUDIO
IN SPDIF OUT
AUDIO OUT
AUDIO IN
DVD / VCR / VCD
HDMI OUT
R
L
R
L
AC IN
Y
HDMI IN
7
DVI IN
RJ-45
VGA IN
Pb
Pr
COMPONENT IN
DVI OUT
VGA OUT
IN
STEREO AMPLIFIER
IN
RS232C
AUDIO OUT
AUDIO IN
USB
USB
IR
3.1.
BDL4220QL
3.2.
Connecting Multiple Displays
3.2.1. RS232C control connection (optional)
DISPLAY 2
DISPLAY 1
[RS-232C]
PC
[RS232C IN]
[RS232C OUT]
[RS232C IN]
[RS232C OUT]
3.2.2. IR connection (optional)
DISPLAY 1
External
IR Receiver
[IR IN]
DISPLAY 2
[IR OUT]
[IR IN]
NOTE:This display’s remote control sensor will stop working if the [IR IN] is connected.
3.3.
IR Pass-through Connection (optional)
DISPLAY
[IR OUT]
DVD / VCR / VCD
[IR IN]
(DVD / VCR / VCD)
Remote Control
(BDL4220QL)
8
[IR OUT]
BDL4220QL
3.4.
Wire-connecting to Network (optional)
If you connect this display to a home network, you can play photos, music and videos from your computer. See Play multimedia files (Page 10) for more
detail.
INTERNET
[RJ-45]
ROUTER
[RJ-45]
PC
To setup the network:
1. Switch on the router and switch on its DHCP setting.
2. Connect the router to this display with an Ethernet cable.
3. Press
button on the remote control, then select {Setup}.
4. Select {Connect to network}, then press
button.
5. Follow the on-screen instructions to install the network.
6. Wait for this display to find the network connection.
7. If you are prompted, agree to the “End User Licence Agreement”.
NOTE:Connecting with a shielded CAT-5 Ethernet cable to comply with the EMC directive.
9
BDL4220QL
4.
Operation
• {News}: Ideal settings for spoken audio, such as the news.
NOTE:The control button described in this section is mainly on the
remote control unless specified otherwise.
4.5.
4.1.
• Your computer connected through your home network.
You can play videos, photos, and music on your display from:
Watch the Connected Video Source
• A USB device connected to this display.
See page 7 for external equipments connection.
1. Press
2. Press
4.2.
button.
or
button to select a device, then press
Play Multimedia Files
4.5.1. Play files from computer
button.
To play files from computer, you will need:
• A wired home network, connected with a Universal Plug and Play
(uPnP) router.
Change Picture Format
You can change the picture format to suit the video source. Each video
source has its available picture formats.
• Optional: A LAN cable that connects your display to your home
network.
The available picture formats depend on the video source:
• A media server running on your computer.
1. Press
• Appropriate settings on your computer firewall to allow you to run
the media server.
button.
2. Press or button to select a picture format, then press
button.
• {Auto zoom}: Enlarge the picture to fill the screen.
Recommended for minimal screen distortion but not for HD or
PC.
Set up the network
• {Movie expand 16:9}: Scale 4:3 format to 16:9. Not
recommended for HD or PC.
2. Switch on your computer and the router.
1. Connect your display and the computer to the same home network.
See page 9 for connecting your display to a network.
NOTE:If the apparatus does not return to DLNA mode due to
external electrical disturbances (e.g. electrostatic discharge), user
intervention is required.
• {Wide screen}: Shows widescreen format content unstretched.
Not recommended for HD or PC.
• {Unscaled}: Provide maximum detail for PC. Only available
when PC mode is selected in the {Picture} menu.
Set up media sharing
1. Install a media server on your computer to share media files. These
are some media servers:
• {4:3}: Display the classic 4:3 format.
4.3.
• For PC: Windows Media Player 11 (or higher) or TVersity
Select your Preferred Picture Settings
• For Mac: Twonky
1. While this display is playing video source, press
button.
2. Press
or
button to select
, then press
button.
2. Switch on media sharing on your computer using the media server.
For more information on how to set up the media server, refer to
the website of the media server.

3. Press or button to select an option, then press
Play files
button:
1. Press
• {Personal}: Apply your personalised picture settings.
button.
2. Select [Browse network], then press
• {Vivid}: Rich and dynamic settings, ideal for daytime viewing.
button.
3. Select a file from the content browser, then press
start playing.
• {Natural}: Natural picture settings.
• {Standard}: Default settings that suit most environments and
types of video.
button to
4. Press the Play buttons on the remote control to control playing.
• {Movie}: Ideal settings for movies.
Tips:
• {Photo}: Ideal settings for photos.
• Select the top bar to filter your files by type.
• {Energy saving}: Settings that conserve the most energy.
• Select [Sort] to arrange the files by album name, artist, or other
fields.
4.4.
Select your Preferred Sound Settings
• To clear the list of offline media servers, press
button, then select [Clear offline servers] and press
1. While this display is playing video source, press
button.
2. Press
or
button to select
, then press
button.

3. Press or button to select an option, then press
button:
• {Personal}: Apply your personalised sound settings.
• {Original}: Settings that suit most environments and types of
audio.
• {Movie}: Ideal settings for movies.
• {Music}: Ideal settings for listening to music.
• {Game}: Ideal settings for games.
10
button.
BDL4220QL
4.5.2. Play multimedia files from USB device
• Do not overload the USB port. If you connect a USB storage
device that consumes more than 500mA power, make sure that it is
connected to its own external power supply.
This display can play music, movie, or photo files from your USB device.
1. Connect your USB device to the USB port on this display.
4.6.
Play options
IN
4.6.1. Playing music files
in the top bar.
OUT
1. Select Music
AUDIO
IN SPDIF OUT
2. Select one music track, then press
AUDIO OUT
IR
IN
RS232C
USB
USB
button.
05:05
AUDIO IN
1. Funky music
2. Press
button, select USB, then press
button.
3. The connected USB device is detected automatically for all its
playable files, which will be automatically sorted into 3 types:
,
, and
.
Info
Play All
Sort
USB device
Help
Options
• To play all the tracks in a folder, select one music file, then select
{Play All}.
• To skip to the next or previous track, press
button.
or
• To pause the track, press
button. Press
button again to
resume playback.
or
button.
• To skip backward or forward 10 seconds, press
• To search backward or forward, press G or J button,
press repeatedly to toggle between different speeds.
• To stop the music, press H button.
Music options
While you play music, press
button to select an option:
Help
• {Repeat}: Select {Repeat} to play a track or an album repeatedly, or
select {Play once} to play a track once.
4. Press the
BACK button to go up to the top layer in the screen.
Press
button to select the file type. Press
button to enter
its play list.
5. Select the file you want. Press
button, then press
• {Media Server}: When you play content from a media server, you
can select another media server.
button to start playing.
• {Shuffle On} / {Shuffle Off}: Enable or disable random play of tracks.
6. Follow the on-screen instruction to control the play option.
NOTE: To view information about a song (for example, title, artist or
duration), select the song, then press
button. To hide
the information, press
button again.
7. Press the PLAY buttons (H F G I J) to control playing.
Supported file system:
• FAT32
Supported file format:
• Music: MP3, WMA, M4A, AAC, AC3
• Movie: AVI, MP4, MOV, MPG/MPEG
• Photo: JPEG, BMP, GIF
Caution:
• The manufacturer is not responsible if the USB device is not
supported, nor is it responsible for damage to or loss of data in the
device.
11
BDL4220QL
4.6.2. Playing movie files
4.6.3. Playing photo files
1. Select Movie
1. Select Photo
in the top bar.
2. Select a video, then press
Info
2. Select a photo thumbnail, then press
button.
The Movie
11:22:33
88.88MB
2013-05-05
The Movie
11:22:33
88.88MB
2013-05-05
The Movie
11:22:33
88.88MB
2013-05-05
The Movie
11:22:33
88.88MB
2013-05-05
Play All
USB device
• To skip to the next or previous video, press
button.
button.
The Movie
11:22:33
88.88MB
2013-05-05
Help
Info
Options
• To play all the videos in a folder, select one video file, then select
{Play All}.
Play All
Sort
USB device
Help
Options
Start a slideshow
If there are multiple photos in a folder, select a photo, then select {Play
All}.
or
button, and
• To skip to the previous or next photo, press
then press
button.
or
• To pause the video, press
button. Press
button again to
resume playback.
or
button.
• To skip backward or forward 10 seconds, press
• To stop the slideshow, press H button.
Slideshow options
• To search backward or forward, press G or J button,
press repeatedly to toggle between different speeds.
While you play a slideshow, press
button to select an option:
• To stop the video, press H button.
button, then press
• {Shuffle Off} / {Shuffle On}: Enable or disable random display of
pictures in the slideshow.
Movie options
While playing video, press
button to select an option:
in the top bar.
button, then press
• {Repeat}: Select {Repeat} to watch a slideshow repeatedly or {Play
once} to watch once.
• {Subtitles}: Select the available subtitle settings.
• {Slideshow Time}: Select the displaying time for each photo in the
slideshow.
• {Subtitle Language}: Select the language for subtitles if available.
• {Character Set}: Select the correct character set for the subtitles.
• {Slideshow Transitions}: Select the transition from one photo to the
next.
• {Audio Language}: Select an audio language.
• {Media Server}: When you play content from a media server, you
can select another media server.
• {Repeat}: Select {Repeat} to play the video file repeatedly or {Play
once} to play the video file once.
• {Media server}: When you play content from a media server, you
can select another media server.
• {Shuffle On} / {Shuffle Off}: Enable or disable random play of video
files.
• {DivX(R) VOD}: Display the DivX registration and deregistration
codes for this display.
NOTE: To view information about a video (for example, played position,
duration, title, or date), select the video, then press
button. To hide the information, press
button again.
12
BDL4220QL
5.
Change your settings
Using this display’s control buttons:
Using the remote control:
INPUT
MENU
1. Press
2. Press
1. Press
button to display the OSD menu.
, or
button to select {Setup}. Press
button to enter.
][
button to confirm menu selection and enter its
4. Press
button to exit the OSD menu.
Quick Picture and Sound
You can select picture and sound settings with the help of the settings
assistant, which demonstrates the effect of your chosen setting
immediately.
1. Press
button.
3. Select {Quick picture and sound}. Press
4. Select {Continue}, then press
button.
button
5. Follow the on-screen instructions to choose your preferred settings.
5.2.
Settings
button to display the OSD menu.
2. Select {Setup}. Press
button to select {Quick picture and sound},
3. Press , , , or
{Settings}, {Connect to network}, or {Network settings}. Press
button to enter.
Quick picture and
sound
] [ ] or [ ] button to select menu item or adjust its
3. Press
submenu.
5.1.
Source
Setup
button to display the OSD menu.
2. Press[
value.
Settings
5.2.1. Picture menu
Connect to network
Network settings
Picture
Picture style
Sound
Restore style
General settings
Backlight contrast
Colour
Sharpness
button to select its menu item or to adjust its
4. Press , , , or
value. Press
button to confirm.
5. Press
6. Press
Noise reduction
MPEG artifact reducti...
button to go back to the previous menu layer.
Digital Crystal Clear
button to exit the OSD menu.
Advanced
Game or computer
Foramat and edges
Picture style
Select a predefined picture setting.
Restore style
Restore the last-selected predefined picture setting.
13
BDL4220QL
5.2.2. Sound menu
Backlight contrast
Adjust the brightness of this display’s backlight.
Colour
Picture
Sound style
Adjust the colour saturation of the picture.
Sound
Restore style
Sharpness
General settings
Bass
Treble
Adjust the sharpness of the picture.
Surround mode
Noise reduction
Audio out
Select the amount of noise reduction for the picture.
Advanced
MPEG artifact reduction
Smoothen transitions and haziness in the digital picture.
Digital Crystal Clear
Fine-tune each pixel to match surrounding pixels and produce a brilliant,
high-definition image.
• {Advanced sharpness}: Enable superior sharpness, especially on
lines and contours in the picture.
Sound style
Access predefined sound settings.
• {Dynamic contrast}: Dynamically enhance the details in the
dark, medium and light areas of the picture.
Restore style
• {Dynamic backlight}: Select a backlight level to optimise dynamic
power consumption and picture contrast.
Restore the last-selected predefined sound setting.
• {Colour enhancement}: Dynamically enhance the vividness and
details of colours.
Adjust the bass level of the speaker and headphones.
Bass
Treble
Advanced
Adjust the treble level of the speaker and headphones.
Access advanced settings such as gamma, tint settings and video contrast
settings.
Surround mode
• {Gamma}: Adjust the non-linear setting for picture luminance
and contrast.
Select a surround sound mode to enhance your audio experience.
• {Tint}: Change the colour balance.
Adjust audio output volume.
Audio out
• {Custom tint}: Customise colour balance setting. Only available
if {Tint}  {Custom} is selected.
• {Video contrast}: Adjust video contrast.
Advanced
Access advanced settings to enhance your audio experience.
• {Auto volume leveling}: Enable the reduction of sudden volume
changes.
• {Brightness}: Adjust screen brightness.
Game or computer
• {Speaker settings}: Turn on or off the internal speakers.
When viewing content from a connected game console, select {Game}
to apply game settings. When a computer is connected through HDMI,
select {Computer}.
• {Clear sound}: Enhance sound quality.
• {Audio out format}: Select the type of audio output through
the digital audio output connector.
Make sure that {Format and edges}  {Picture format}  {Unscaled}
is selected so as to view maximum detail.
• {Audio out leveling]: Set the output level for stereo audio.
Select {Less} for a certain amount of loss in intensity or signal
strength. Select {More} for no loss in intensity or signal strength.
Format and edges
• {Audio out delay}: Automatically sync the image on this display
to the audio from a connected home theatre.
Access advanced settings to control the displaying format of the picture.
• {Picture format}: Change the picture format.
• {Audio out offset}: Adjust the setting for audio output delay.
Available if {Audio out delay} is switched on.
• {Screen edges}: Change the picture size.
• {Picture shift}: If available, move the position of the picture.
14
BDL4220QL
5.2.3. General settings menu
Picture
Menu language
Sound
Monitor id
General settings
Eco mode
• {Lock but volume}: Disable all the button function except the
button.
• {Lock but power}: Disable all the button function except the
button.
NOTE: To disable the lock function from [Local KB lock] or [RC
lock] item, press buttons
1998
on the remote
control.
Auto search
Clock
USB scheduling
Factory settings
Sleep timer
Reset all your customized settings to the factory defaults.
Auto switch off
5.3.
Local KB lock
RC lock
Factory settings
Network Settings
View network settings
Network settings
Static IP Configuration
Menu language
Digital Media Renderer ..
Select language used for OSD menus.
Monitor id
Set the ID number for controlling this display via the RS232C
connection. Each display must have a unique ID number when multiple
sets of this display are connected.
Eco mode
Set this display to reduce the power consumption automatically.
Auto search
Choose to let this display detect and display available signal sources
automatically.
View network settings
View connected network status.
Clock
Network settings
Adjust clock settings.
Select how this display should assign addresses to the network
resources.
USB scheduling
This function allows you to program up to 3 different scheduled time
intervals for this display to activate, and auto play USB media file of your
setting.
Static IP Configuration
Assign {IP address}, {Netmask}, {Gateway}, {DNS1}, and {DNS2} for
this display.
After changing the {Clock} option in the {General settings} menu, you need
to set this {USB scheduling} again.
Digital Media Renderer - DMR
Receive multimedia files from Smart Phones or Tablets connected to
your network.
Sleep timer
Switch off this display after a specified time.
Auto switch off
Set the time for this display to be switched off after a period of no
activity. Press any key on the remote control to disable this function.
Local KB lock
Choose to enable or disable the keyboard (control buttons) function of
this display.
• {Unlock}: Enable the keyboard function.
• {Lock all}: Lock all keyboard function.
• {Lock but volume}: Disable all the keyboard function except the
and
button.
• {Lock but power}: Disable all the keyboard function except the
button.
RC lock
Choose to enable or disable the button function of the remote control.
• {Unlock}: Enable the button function.
• {Lock all}: Lock all button function.
15
BDL4220QL
6.
Input mode
PC Resolution:
Standard
Resolution
Active Resolution
H Pixels
Refresh Rate
Pixel Rate
480
60 Hz
25.175 MHz
480
72 Hz
31.5 MHz
480
75 Hz
31.5 MHz
400
70 Hz
33.75 MHz
600
60 Hz
40 MHz
600
75 Hz
49.5 MHz
768
60 Hz
65 MHz
768
75 Hz
78.75 MHz
V Lines
Aspect Ratio
Stand for Mode
4:3
Video Graphic Array
16:9
Wide Video Graphic Array
4:3
Super VGA
4:3
Extended Graphic Array
VGA
640
WVGA
720
SVGA
800
XGA
1024
WXGA
1280
768
60 Hz
79.5 MHz
5:3
Wide XGA
WXGA
1280
800
60 Hz
79.5 MHz
16:10
Wide XGA
SXGA
1280
1024
60 Hz
108 MHz
5:4
Super XGA
WXGA
1360
768
60 Hz
85.5 MHz
16:9
Wide XGA
UXGA
1600
1200
60 Hz
162 MHz
4:3
Ultra XGA
HD1080
1920
1080
60 Hz
148.5 MHz
16:9
HD1080
Refresh Rate
Pixel Rate
Aspect Ratio
Stand for Mode
29.97 Hz
13.5 MHz
59.94 Hz
27 MHz
4:3
Modified NTSC Standard
25 Hz
13.5 MHz
50 Hz
27 MHz
4:3
Modified PAL Standard
Refresh Rate
Pixel Rate
Aspect Ratio
Stand for Mode
74.25 MHz
16:9
Normally DVB Mode
74.25 MHz
16:9
Normally ATSC Mode
148.5 MHz
16:9
Normally ATSC Mode
SDTV Resolution:
Standard
Resolution
480i
480p
576i
576p
Active Resolution
H Pixels
V Lines
720
480
720
480
HDTV Resolution:
Active Resolution
Standard
Resolution
H Pixels
V Lines
720p
1280
720
1080i
1920
1080
1080p
1920
1080
50 Hz
60 Hz
25 Hz
30 Hz
50 Hz
60 Hz
• The PC text quality is optimum in HD 1080 mode (1920 × 1080, 60 Hz).
• Your PC display screen might appear different depending on the manufacturer (and your particular version of Windows).
• Check your PC instruction book for information about connecting your PC to a display.
• If a vertical and horizontal frequency-select mode exists, select 60 Hz (vertical) and 31.5 KHz (horizontal). In some cases, abnormal signals (such as
stripes) might appear on the screen when the PC power is turned off (or if the PC is disconnected). If so, press the [
] button to enter the
video mode. Also, make sure that the PC is connected.
• When horizontal synchronous signals seem irregular in RGB mode, check PC power saving mode or cable connections.
• This display settings table complies to the IBM/VESA standards, and based on the analog input.
• The DVI support mode is regarded as same to the PC support mode.
• The best timing for the vertical frequency to each mode is 60 Hz.
16
BDL4220QL
7.
Pixel Defect Policy
We strive to deliver the highest quality products and use some of the industry’s most advanced manufacturing processes whilst practicing stringent quality
control. However, pixel or sub-pixel defects on the PDP / TFT panels used in Plasma- & LCD- displays are sometimes unavoidable. No manufacturer can
guarantee that all panels will be free from pixel defects, but Philips guarantees that any Plasma- & LCD- displays with an unacceptable number of defects
will be repaired during the warranty period in line with your local guarantee conditions.
This notice explains the different types of pixel defects and defines the acceptable defect level for the LCD screen. In order to qualify for repair under
warranty, the number of pixel defects must exceed a certain level as shown in the reference table. If the LCD screen is within specification a warranty
exchange / claim back will be refused. Additionally, because some types or combinations of pixel defects are more noticeable than others, Philips sets even
higher quality standards for those.
7.1.
Pixels and Sub-pixels
A pixel, or picture element, is composed of three sub-pixels in the primary colors of red, green and
blue. Many pixels together form an image. When all sub-pixels of a pixel are lit, the three colored
sub-pixels together appear as a single white pixel. When all are dark, the three colored sub-pixels
together appear as a single black pixel. Other combinations of lit and dark sub-pixels appear as
single pixels of other colors.
subpixel
pixel
7.2.
Types of Pixel Defects + Dot Definition
Pixel and sub-pixel defects appear on the screen in different ways. There are three categories of pixel defects and several types of sub-pixel defects within
each category.
Dot definition = What is a defective “Dot”? :
One or more defective, adjacent sub-pixel are defined as one “dot”. The no. of defective sub-pixels are not relevant to define a defective dot. This means
that a defective dot can consist of one, two or three defective sub-pixels which can be dark or lit.
R G B
One dot = One Pixel; consists of three sub-pixels of Red, Green, and Blue.
7.3.
Bright Dot Defects
Bright dot defects appear as pixels or sub-pixels that are always lit or “on”. These are the examples of bright dot defects:
One lit red, green or blue sub pixel
Two adjacent lit sub pixels:
Red + Blue = Purple
Red + Green = Yellow
Green + Blue = Cyan (Light Blue)
17
Three adjacent lit sub pixels (one white pixel)
BDL4220QL
7.4.
Dark Dot Defects
Black dot defects appear as pixels or sub-pixels that are always dark or “off ”. These are the examples of black dot defects:
One dark dot
7.5.
Two adjacent dark dots = 1 pair of dark dots
Two dark dots, specifications defines the
minimum distance between dark dots
Proximity of Pixel Defects
Because pixel and sub-pixels defects of the same type that are nearby one another may be more noticeable, Philips also specifies tolerances for the
proximity of pixel defects. In the table below you can find specifications about:
• Allowed amount of adjacent dark dots = (adjacent dark dots =1 pair of dark dots)
• Minimum distance between dark dots
• Total no. of all defective dots
7.6.
Pixel Defect Tolerances
In order to qualify for repair due to pixel defects during the warranty period, a PDP / TFT panel in a Philips Plasma / LCD- display must have pixel or subpixel defects exceeding the tolerances listed in the following table.
BRIGHT DOT EFFECT
ACCEPTABLE LEVEL
1 lit sub pixel
2
BLACK DOT EFFECT
ACCEPTABLE LEVEL
1 dark sub pixel
10
TOTAL DOT DEFECTS OF ALL TYPES
12
NOTE:* 1 or 2 adjacent sub pixel defects = 1 dot defect
7.7.
MURA
Dark spots or patches may occasionally appear on some liquid crystal display (LCD) panels. This is known within the industry as Mura, which is a Japanese
term for “unevenness.” It is used to describe an irregular pattern or area in which uneven screen uniformity appears under certain conditions. Mura is a
result of the deterioration of the liquid crystal alignment layer and is most commonly caused by long-term operation under high ambient temperatures. It
is an industry- wide phenomenon and Mura is not repairable. It is also not covered by our warranty terms.
Mura has been around since the introduction of LCD technology and with screens getting bigger and in operation 24/7, many displays are running in low
light conditions. This all adds to the possibility of Mura affecting displays.
HOW TO SPOT MURA
There are many symptoms of Mura and also multiple causes. Several of these are listed below:
• Impurities or foreign particles in the crystal matrix
• Uneven distribution of LCD matrix during manufacturing
• Non-uniform luminance distribution of the backlight
• Panel assembly induced stress
• Flaws within the LCD cells
• Thermal induced stress – high temperature operation over long periods of time
HOW TO AVOID MURA
Although we can not guarantee the complete eradication of Mura every time, in general the appearance of Mura can be minimized by these methods:
• Lower the backlight brightness
• Use a screen saver
• Reduce the ambient temperature around the unit
18
BDL4220QL
8.
Cleaning and Troubleshooting
8.1.
Cleaning
Caution When Using the Display
• Do not bring your hands, face or objects close to the ventilation holes of the display. The top of the display is usually very hot due to the high
temperature of exhaust air being released through the ventilation holes. Burns or personal injuries may occur if any body parts are brought too
close. Placing any object near the top of the display could also result in heat related damage to the object as well as the display itself.
• Be sure to disconnect all cables before moving the display. Moving the display with its cables attached may damage the cables and thus cause fire
or electric shock.
• Disconnect the power plug from the wall outlet as a safety precaution before carrying out any type of cleaning or maintenance procedure.
Front Panel Cleaning Instructions
• The front of the display has been specially treated. Wipe the surface gently using only a cleaning cloth or a soft, lint-free cloth.
• If the surface becomes dirty, soak a soft, lint-free cloth in a mild detergent solution. Wring the cloth to remove excess liquid. Wipe the surface of
the display to remove dirt. Then use a dry cloth of the same type to dry.
• Do not scratch or hit the surface of the panel with fingers or hard objects of any kind.
• Do not use volatile substances such as insert sprays, solvents and thinners.
Cabinet Cleaning Instructions
• If the cabinet becomes dirty, wipe the cabinet with a soft, dry cloth.
• If the cabinet is extremely dirty, soak a lint-free cloth in a mild detergent solution. Wring the cloth to remove as much moisture as possible. Wipe
the cabinet. Use another dry cloth to wipe over until the surface is dry.
• Do not allow any water or detergent to come into contact with the surface of the display. If water or moisture gets inside the unit, operating
problems, electrical and shock hazards may result.
• Do not scratch or hit the cabinet with fingers or hard objects of any kind.
• Do not use volatile substances such as insert sprays, solvents and thinners on the cabinet.
• Do not place anything made from rubber or PVC near the cabinet for any extended periods of time.
19
BDL4220QL
8.2.
Troubleshooting
Symptom
Possible Cause
Remedy
No picture is displayed
1. The power cord is disconnected.
1. Plug in the power cord.
2. The main power switch on the back of the
display is not switched on.
2. Make sure the power switch is switched on.
3. The selected input has no connection.
3. Connect a signal connection to the display.
4. The display is in standby mode.
Interference displayed on the display or audible
noise is heard
Caused by surrounding electrical appliances or
fluorescent lights.
Move the display to another location to see is the
interference is reduced.
Color is abnormal
The signal cable is not connected properly.
Make sure that the signal cable is attached firmly
to the back of the display.
Picture is distorted with abnormal patterns
1. The signal cable is not connected properly.
1. Make sure that the signal cable is attached
firmly.
2. The input signal is beyond the capabilities of
the display.
2. Check the video signal source to see if it
is beyond the range of the display. Please
verify its specifications with this display’s
specification section.
Display image doesn’t fill up the full size of the
screen
The zoom mode is not correctly set.
Use the Zoom mode or Custom zoom function
in the Screen menu to fine tune display geometry
and time frequency parameter.
Can hear sound, but no picture
Improperly connected source signal cable.
Make sure that both video inputs and sound
inputs are correctly connected.
Can see picture but no sound is heard
1. Improperly connected source signal cable.
1. Make sure that both video inputs and sound
inputs are correctly connected.
2. Volume is turned all the way down.
3. [MUTE] is turned on.
2. Press [
4. No external speaker connected.
3. Switch MUTE off by using the
button.
] or [
] button to hear sound.
[
]
4. Connect external speakers and adjust the
volume to a suitable level.
Some picture elements do not light up
Some pixels of the display may not turn on.
This display is manufactured using an extremely
high level of precision technology: however,
sometimes some pixels of the display may not
display. This is not a malfunction.
After-Images can still be seen on the display
after the display is powered off. (Examples
of still pictures include logos, video games,
computer images, and images displayed in 4:3
normal mode)
A still picture is displayed for an over extended
period of time
Do not allow a still image to be displayed for
an extended period of time as this can cause a
permanent after-image to remain on the display.
20
BDL4220QL
9.
Technical Specifications
Display:
Item
Specifications
Screen Size (Active Area)
42” LCD (106.7 cm)
Aspect Ratio
16:9
Number of Pixels
1920 (H) × 1080 (V)
Pixel Pitch
0.4845 (H) × 0.4845 (V) [mm]
Displayable Colors
16.7 Million colors
Brightness
350 cd/m²
Contrast Ratio (Typical)
3000:1
Viewing Angle
178 degrees
In/Out Terminals:
Item
Specifications
Speaker Output
Internal Speakers
7W (L) + 7W (R) [RMS]/16Ω, 1 Way 1 Speaker System
Audio Output
RCA Jack × 2
0.5V [rms] (Normal) / 2 Channel (L+R)
Audio Input
3.5 mm Stereo × 1
0.5V [rms] (Normal) / 2 Channel (L+R)
82 dB/W/M/160 Hz ~ 13 KHz
RCA Jack × 2
RS232C Input/Output
2.5 mm × 2
TXD + RXD (1:1)
LAN
RJ-45 Jack × 1 (8 pin)
10/100 LAN Port
HDMI Input
HDMI Jack × 1
(Type A) (19 pin)
Digital RGB: TMDS (Video + Audio)
MAX:
Video: 720p, 1080p, 1920 × 1080/60 Hz (WUXGA)
Audio: 48 KHz / 2 Channel (L+R)
Supports LPCM only
DVI-D Input
DVI-D jack
Digital RGB: TMDS (Video)
VGA Input
D-Sub Jack × 1 (15 pin)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ), SOG: 1V [p-p] (75Ω)
Component Input
RCA Jack × 3
SPDIF Output
SPDIF Port
Serial digital audio output when input is HDMI
IR Input/Output
3.5 mm × 2
IR pass through or IR daisy chain
USB Input
USB × 1 (Type B)
USB 2.0, External PC connection
MAX: 720p, 1080p, 1920 × 1080/60 Hz (WUXGA)
Y: 1V [p-p] (75Ω), Pb: 0.7V [p-p] (75Ω), Pr: 0.7V [p-p] (75Ω)
MAX: 480i, 576i, 480p, 576p, 720p, 1080i, 1080p
General:
Item
Specifications
Power Input
100-240V
Power Consumption (Max.)
95 W
Power Consumption (Typical)
80 W
Power Consumption (EPA6.0)
55 W
Power Consumption (Standby & Off)
< 0.5W (OSD: APM mode off)
Dimensions [W × H × D]
980.4 × 572.9 × 38.5 mm
Weight
11.9 Kg
Gross Weight
15.3 Kg
50-60Hz, 2.5A
Environmental Condition:
Item
Temperature
Humidity
Altitude
Specifications
Operational
5 ~ 40°C
Storage
-20 ~ 60°C
Operational
20 ~ 80% RH (No condensation)
Storage
10 ~ 90% RH (No condensation)
Operational
0 ~ 2,000 m
Storage
0 ~ 5,000 m
21
© 2013 Koninklijke Philips Electronics N.V. All rights reserved.
Philips and the Philips Shield Emblem are registered trademarks of
Koninklijke Philips Electronics N.V. and are used under license from
Koninklijke Philips Electronics N.V.
Specifications are subject to change without notice.