Register your product and get support at
Short user manual
Important safety
•The Electrical network is classified as hazardous.
The only way to power down the charger is to
unplug the power supply from the electrical outlet.
Ensure that the electrical outlet is always easily
•Refer to safety information before using the
•This product complies with European R&TTE
directive 1999/5/EC
•Use only the power supply listed in the user
•Use only the batteries listed in the user
•Do not allow the product to come into contact
with liquids.
•Risk of explosion if battery is replaced by an
incorrect type.
•Dispose of used batteries according to the
•When the handset rings or when the handsfree is
activated, keep the handset away from your ear to
avoid hearing damage.
In call
Adjust the volume.
End calls.
Mute/unmute the microphone.
Enter a pause.
Recall (network dependent).
In menu
Confirm / Enter the option menu. / Select
Up / down
Exit menu.
Access the main menu.
Display icons
Call log
Make and receive calls.
Make intercom call.
Lock/unlock the keypad.
In text input
Delete text
Enter a space.
Find handset
Display icons
It displays the connection between the handset
and the base. The more bars are shown, the
better the signal strength is.
It remains steadily on when browsing incoming
calls in the call log.
It indicates an outgoing call in the redial list.
It flashes when there is a new missed call or
when browsing new missed calls. It remains
steadily on when browsing the missed calls in
call log that are already read.
It flashes when receiving incoming call. It remains
steadily on during a call.
The ringer is off.
Voice messages indicator: flashes for new
messages, is steady for reviewed messages.
* This is network dependent.
It displays when you scroll up/down a list or
increase and decrease the volume.
There are more digits on the right. Press
Multi-handset version
Get started
Insert batteries
Charge your phone
Configure your phone
1When using your phone for the first time, you see a
welcome message (country dependent).
2Set the country and language if prompted.
3Set the date and time.
• If the time is in 12-hour format, press / to
select [AM] or [PM] (country dependent).
Charge 8 hours
> 70%
10% - 40%
40% - 70%
< 10%
Flashing: low battery
Scrolling: charging in progress
Add record
2Select [PHONEBOOK] > [ADD NEW].
3Follow on-screen instructions.
Call from the phonebook
1Press .
2Select a record and press .
Direct access memory
You have 2 direct access memories (Keys 1 and 2).
To dial the saved phone number automatically, press
and hold on the keys in standby mode.
Depending on your country, keys 1 and 2 are preset
to [1_VOICEMAIL] (voice mail number) and
[2_INFO SVC] (information service number)
of your network operator respectively (network
Call log
Call from the call log
1Press .
2Select a record and press
Save record
1Press >
2Follow on-screen instructions.
Delete record
1Press >
2Follow on-screen instructions.
Redial list
Call from the redial list
2Select a record and press .
Save record
2Follow on-screen instructions.
Delete record
2Follow on-screen instructions.
Register additional handsets
You can register additional handsets to the base
1Press and hold on the base station for 5 seconds.
3Select [SERVICES] > [REGISTER], then press
to confirm.
4Enter the system PIN/passcode (0000).
to confirm the PIN/passcode.
»» Registration is complete in less than 2 minutes.
Restore default settings
You can reset your phone settings to the original
factory settings.
2Select [SERVICES] > [RESET], then press
to confirm.
3Follow on-screen instructions.
• You may recall the original PIN/passcode by
following this procedure.
Technical data
• Philips:2 x AAA NiMH 1.2 V Rechargeable
550 mAh batteries
Use only the supplied batteries.
Base and charger:
100-240 V~
100-240 V~
50/60 Hz 0.15 A
50/60 Hz 0.2 A
Output: 6 V 400 mA
6 V 500 mA
Phonebook with 50 entries
Call log with 20 entries
Talk time: 16 hours
Standby time: 250 hours
• You can install a DSL (digital subscriber line) filter to
prevent noise and caller ID problems caused by the
DSL interference.
• You can find the Declaration of Conformity on
Frequently asked questions
No signal bar is displayed on the screen.
• The handset is out of range. Move it closer to the
base station.
• If the handset displays [UNREGISTERED],
register your handset. (See the section on “Register
additional handsets”).
If I fail to pair (register) the additional handsets to
the base station, what do I do?
Your base memory is full. Access
[SERVICES] > [UNREGISTER] to unregister
the unused handsets and try again.
I have chosen a wrong language which I cannot
read, what do I do?
to go back to the standby screen.
to access the main menu screen.
3The following options will appear on the screen:
4Select it to access the language options.
5Select your own language.
My handset is in searching status, what do I do?
• Make sure that the base station has power supply.
• Register the handset to the base station.
• Move the handset closer to the base station.
I cannot change the settings of my voice mail, what
do I do?
The voice mail service is managed by your service
provider but not the phone itself. Contact your
service provider to change the settings.
No display
• Make sure the batteries are charged.
• Make sure there are power and phone connections.
The handset on the charger does not charge.
• Make sure the batteries are inserted correctly.
• Make sure the handset is placed properly on the
charger. The battery icon animates when charging.
• Make sure the docking tone setting is turned on.
When the handset is placed correctly on the
charger, you can hear a docking tone.
• The charging contacts are dirty. Disconnect the power
supply first and clean the contacts with a damp cloth.
• Batteries are defective. Purchase new ones with
the same specifications.
Bad audio (crackles, echo, etc.)
• The handset is nearly out of range. Move it closer
to the base station.
• The phone receives interference from the nearby
electrical appliances. Move the base station away
from them.
• The phone is at a location with thick walls. Move
the base away from them.
The handset does not ring.
Make sure the handset ringtone is turned on.
The caller ID does not display.
• The service is not activated. Check with your
service provider.
• The caller’s information is withheld or unavailable.
For information, refer to the extended user
documentation online.
When this crossed-out wheeled bin symbol is
attached to a product it means that the product
is covered by the European Directive 2002/96/EC.
2014 © WOOX Innovations Limited.
All rights reserved.
Philips and the Philips’ Shield Emblem are
registered trademarks of Koninklijke Philips N.V.
and are used by WOOX Innovations Limited
under license from Koninklijke Philips N.V.