Extron DMS 2000 & 3200 spec sheet

DMS 2000 and DMS 3200
The Extron DMS Series Modular DVI Matrix Switchers represent a new level of matrix switching for
DVI. They combine the simplicity and reliability of a fixed I/O matrix switcher with the convenience
and flexibility of a modular matrix switcher. DMS Series matrix switchers accept any combination
of available DMS DVI or DMS Fiber matrix boards. Input and output boards are available in 4input, 4-output, and 4x4 I/O versions, providing various I/O size combinations with sizes from 4x4
to 36x36, depending on the DMS Matrix Switcher Frame selected. The DMS Series is ideal for a
wide range of applications that require routing of high-resolution DVI digital video signals without
copy protection.
Video — DMS DVI
Routing
1600 Series
2000 Series
3200 Series
3600 Series
Gain
Resolution range
Signal type
Digital video
NOTE
From 4 x 4 to 16 x 16 matrix, expandable by increments of 4 inputs and
4 outputs
From 4 x 4 to 20 x 20 matrix, expandable by increments of 4 inputs and
4 outputs
From 4 x 4 to 32 x 32 matrix, expandable by increments of 4 inputs and
4 outputs
From 4 x 4 to 36 x 36 matrix, expandable by increments of 4 inputs and
4 outputs
Unity
Up to 1080p (HDTV) or 1920x1200 (the highest resolution of the single
link DVI standard) @ 48, 50, or 60 Hz
Single-link DVI digital video signals are supported.
RGB digital video (DVI and HDMI standards) or Y, Cr, Cb digital
component video (HDMI), actively buffered (supports all single link DVI
and HDMI [if using an optional adapter] standards from 640x480 @ 60
Hz to 1600x1200 @ 60 Hz computer video)
The DMS DVI Series boards are not HDCP compliant.
Digital audio
Consumer Electronics
Control (CEC)
EDID and DDC
HDCP
HPD
Maximum data rate
Maximum pixel clock
Standards
Switching speed
Embedded audio from HDMI sources can be passed, as long as it is not
HDCP encrypted content
Not supported
Supports Extended Display Identification Data (EDID) and Display Data
Channel (DDC) data using DVI and HDMI standards. EDID and DDC
signals are actively buffered.
Not supported
Supports hot plug detection (HPD) of display as a pass-through signal.
4.95 Gbps (1.65 Gbps per color)
165 MHz
DVI 1.0
200 ns, max.
Video input — DMS 44 DVI and DMS 4i DVI input boards
Number/signal type
Connectors
Equalization
Input cable length
NOTE
4 digital RGB single link DVI-D per input board
4 female DVI-I (digital only) per input board
Automatic
100' (30 m) at 1920x1200 @ 48, 50, or 60 Hz; or 1080p; 8 bit color
The transmission distance varies depending on the signal resolution and on the type of
cable, graphics card, and display used in the system.
Video output — DMS 44 DVI and DMS 4o DVI output boards
Number/signal type
Connectors
Re-clocking
Output cable length
Peripheral device power
4 digital RGB single link DVI-D per output board
4 female DVI-I (digital only) per output board
Automatic
50' (15.24 m) at 1920x1200 @ 48, 50, or 60 Hz; or 1080p
250 mA per output
Optical specifications — fiber optic boards
NOTE
The I/O boards are class 1 laser products. They meet the safety regulations of IEC-60825,
FDA 21 CFR 1040.10, and FDA 21 CFR 1040.11.
Number/type
Connectors
Operating distance
NOTE
4 multimode fiber optic inputs and outputs (4 Tx and 4 Rx) per I/O board
4 or 8 LC connectors per I/O board
300 m (985')
Operating distance is approximate. These are typical distances. The maximum distance may
be greater than these typical numbers depending on factors such as fiber type, fiber
bandwidth, connector splicing, losses, modal or chromatic dispersion, environmental
factors, and kinks.
Nominal peak wavelength
Transmission power
Maximum receiver sensitivity
Optical loss budget
Maximum channel data rate
850 nm for multimode (MM)
-5 dBm, typical
-12 dBm, typical
8 dB, maximum
6.25 Gbps
Video — fiber optic (DMS 44, DMS 4i, and DMI 4o fiber boards)
Routing
1600 Series
2000 Series
3200 Series
3600 Series
4 x 4 to
outputs
4 x 4 to
outputs
4 x 4 to
outputs
4 x 4 to
outputs
16 x 16 matrix, expandable by increments of 4 inputs and 4
20 x 20 matrix, expandable by increments of 4 inputs and 4
32 x 32 matrix, expandable by increments of 4 inputs and 4
36 x 36 matrix, expandable by increments of 4 inputs and 4
Video input — DMS 44 fiber and DMS 4i fiber input boards
NOTE
The fiber optic input boards require connection to a DFX 100 Tx transmitter.
Number/signal type
Connectors
Input cable length
NOTE
4 fiber optic, multimode (OM3 or OM4 fiber recommended)
4 LC connectors
300 m (985')
The transmission distance varies depending on the signal resolution and on the type of
cable, graphics card, and display used in the system.
Video output — DMS 44 fiber and DMS 4o fiber output boards
NOTE
The fiber optic output boards require connection to a DFX 100 Rx receiver.
Number/signal type
Connectors
Output cable length
4 fiber optic, multimode (OM3 or OM 4 recommended)
4 LC connectors per board
300 m (985')
Control/remote — switcher host ports
Serial host control port
Baud rate and protocol
1 bidirectional RS-232 or RS-422, rear panel 9-pin female D connector
9600 (default), 19200, 38400, 115200 baud, adjustable; 8 data bits, 1
stop bit, no parity
Serial control pin configurations
9-pin female D connector
RS-232
RS-422
USB control ports
USB standards
Ethernet control port
Ethernet data rate (for
network communication)
Ethernet protocol
Ethernet default settings
Web server
Program control
2 = Tx, 3 = Rx, 5 = GND
2 = Tx-, 3 = Rx-, 5 = GND, 7 = Rx+, 8 = Tx+
1 front panel female mini USB B
USB 2.0, low speed
1 RJ-45 female
10/100Base-T, half/full duplex with autodetect
ARP, ICMP (ping), IP, TCP, DHCP, HTTP, SMTP, Telnet
Link speed and duplex level = autodetected
IP address = 192.168.254.254
Subnet mask = 255.255.0.0
Default gateway = 0.0.0.0
DHCP = off
Up to 200 simultaneous sessions
7.0 MB nonvolatile user memory
Extron control/configuration program for Windows®
Extron Simple Instruction Set (SIS ™)
Microsoft® Internet Explorer® ver. 6 or higher, Telnet
General
Power supply
DMS 1600
DMS 2000
DMS 3200
DMS 3600
Power consumption
DMS 1600
DMS 2000
DMS 3200
DMS 3600
Internal: 1 or 2* (positive-negative)
Input: 100-240 VAC, 50-60 Hz
*A redundant power supply is optional.
Internal: 1
Input: 100-240 VAC, 50-60 Hz
Internal: 1
Input: 100-240 VAC, 50-60 Hz
Internal, 2*(positive-negative)
Input: 100-240 VAC, 50-60 Hz
*A redundant power supply is standard.
Primary power supply: 97 watts
Primary and redundant supplies: 107 watts
Measured fully loaded with (4) 4x4 I/O boards
116 watts
Measured fully loaded with (5) 4x4 I/O boards
174 watts
Measured fully loaded with (8) 4x4 I/O boards
212 watts
Measured fully loaded with (9) 4x4 I/O boards
I/O boards
Temperature/humidity
Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Fan, right to left (as viewed from front panel)
Cooling
Thermal dissipation, full load
DMS 1600
Primary power supply: 332 BTU/hr
Primary and redundant supplies: 366 BTU/hr
Measured fully loaded with (4) 4x4 I/O boards
DMS 2000
398 BTU/hr
Measured fully loaded with (5) 4x4 I/O boards
DMS 3200
596 BTU/hr
Measured fully loaded with (8) 4x4 I/O boards
DMS 3600
724 BTU/hr
Measured fully loaded with (9) 4x4 I/O boards
Rack mount
Yes
Enclosure type
Metal
Enclosure dimensions
DMS 1600
7.0" H x 17.0" W x 12" D (4U high, full rack wide)
(13.3 cm H x 43.2 cm W x 30.5 cm D)
(Depth excludes connectors and buttons. Width excludes rack ears.)
DMS 2000
5.2" H x 17.0" W x 12.2" D (3U high, full rack wide)
(13.3 cm H x 43.2 cm W x 31.0 cm D)
(Depth excludes connectors and buttons. Width excludes rack ears.)
DMS 3200
8.7" H x 17.0" W x 12.2" D (5U high, full rack wide)
(22.1 cm H x 43.2 cm W x 31.0 cm D)
(Depth excludes connectors and buttons. Width excludes rack ears.)
DMS 3600
14.0" H x 17.0" W x 12.25" D (8U high, full rack wide)
(35.6 cm H x 43.1 cm W x 31.1 cm D)
(Depth excludes connectors and handles. Width excludes rack ears.)
Product weight with boards
installed
DMS 1600
With primary power
supply only
With both primary and
redundant power supplies
DMS 2000
DMS 3200
DMS 3600
Shipping weight with boards
installed
DMS 1600
DMS 2000
DMS 3200
DMS 3600
DIM weight with boards
installed
USA/Canada
DMS 2000
DMS 3200
International
DMS 2000
DMS 3200
DMS 3600
Vibration
Regulatory compliance
Safety
EMI/EMC
Environmental
Warranty
26.9 lbs (12.2 kg)
27.9 lbs (12.6 kg)
16.4 lbs (7.5 kg)
27.1 lbs (12.3 kg)
38.5 lbs (17.5 kg)
32
21
33
48
lbs
lbs
lbs
lbs
(15
(10
(15
(22
kg)
kg)
kg)
kg)
23 lbs (11 kg)
39 lbs (18 kg)
28 lbs (13 kg)
47 lbs (22 kg)
52 lbs (24 kg)
ISTA 1A in carton (International Safe Transit Association)
CE, c-UL, UL
CE, C-tick, FCC Class A, ICES
Complies with the appropriate requirements of RoHS, WEEE
3 years parts and labor