Polaris 2010 Breeze User's Manual

Pantone 426 C
Owner's Manual
for Maintenance and Safety
Pantone 426 C
Improper vehicle use can result in SEVERE INJURY or DEATH.
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
Do not start vehicle until all occupants are seated.
Remain seated, holding handles, while the vehicle is in motion.
Operate from driver’s side only.
Always wear your seatbelt to prevent ejection from vehicle.
The roof is not designed or intended to provide rollover
protection. Vehicle rollover could cause severe injury or death.
Always operate with caution.
Never operate after or while using Alcohol or Drugs.
Never operate on slopes steeper than 15 degrees
15°.
Drive slowly straight up and down slopes.
Keep entire body in the vehicle at all times.
Reduce speed and use extra caution when carrying passengers.
Avoid sharp turns or turns during heavy acceleration.
Operate slowly in reverse and avoid sharp turns or sudden braking.
Make sure passengers read and follow all safety labels.
This vehicle is restricted to a maximum of 4 occupants.
When towing the vehicle, the Master ON-OFF Switch MUST be
in the OFF position or severe motor damage will occur.
Place the Master ON-OFF Switch in the OFF position if storing
the vehicle for more than 5 days. Failure to do so may lead to
complete battery discharge and battery damage.
Batteries require regular maintenance. Failure to maintain
batteries in accordance with the owner’s manual can result in
battery damage, vehicle malfunction, fire, and/or severe
injury or death.
For your nearest Polaris dealer,
call 1-800-POLARIS
or visit www.polarisindustries.com
Polaris Sales Inc.,
2100 Hwy. 55, Medina, MN 55340
Phone 1-888-704-5290
Part No. 9922699 Rev 01
Printed in USA
WELCOME
Thank you for purchasing a Polaris vehicle, and welcome to our worldwide family of Polaris owners. We proudly produce an exciting line of
utility and recreational products.
• Snowmobiles
• All-terrain vehicles (ATVs)
• RANGER® utility vehicles
• Neighborhood vehicles (NVs)
• Victory Motorcycles®
We believe Polaris sets a standard of excellence for all utility and recreational vehicles manufactured in the world today. Many years of experience have gone into the engineering, design, and development of your
Polaris vehicle, making it the finest machine we’ve ever produced.
For safe and enjoyable operation of your vehicle, be sure to follow the
instructions and recommendations in this owner’s manual. Your manual
contains instructions for minor maintenance, but information about
major repairs is outlined in the Polaris Service Manual and should be
performed only by a factory certified Master Service Dealer® (MSD)
technician.
Your Polaris dealer knows your vehicle best and is interested in your
total satisfaction. Be sure to return to your dealership for all of your service needs during, and after, the warranty period.
We also take great pride in our complete line of apparel, parts and accessories, available through our online store at www.purepolaris.com.!
1
POLARIS, THE WAY OUT are registered trademarks of Polaris Industries Inc.
Copyright 2009 Polaris Sales Inc. All information contained within this publication is
based on the latest product information at the time of publication. Due to constant
improvements in the design and quality of production components, some minor discrepancies may result between the actual vehicle and the information presented in this publication. Depictions and/or procedures in this publication are intended for reference use
only. No liability can be accepted for omissions or inaccuracies. Any reprinting or reuse
of the depictions and/or procedures contained within, whether whole or in part, is
expressly prohibited.
Printed in U.S.A.
2009 BREEZE Neighborhood Vehicle Owner’s Manual
P/N 9922699
2
TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Features and Controls . . . . . . . . . . . . . . . . . . . 24
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Polaris Products. . . . . . . . . . . . . . . . . . . . . . . . 75
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . 76
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Maintenance Log . . . . . . . . . . . . . . . . . . . . . . . 82
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
3
INTRODUCTION
The following signal words and symbols appear throughout this manual
and on your vehicle. Your safety is involved when these words and symbols are used. Become familiar with their meanings before reading the
manual.
The safety alert symbol indicates a potential personal injury hazard.
WARNING
A WARNING indicates a hazardous situation which, if not avoided, may result in
death or serious injury.
CAUTION
A CAUTION indicates a hazardous situation which, if not avoided, may result in
minor or moderate injury.
NOTICE
A NOTICE indicates a situation that may result in property damage.
The Prohibition Safety Sign indicates an action NOT to take in order
to avoid a hazard.
The Mandatory Action Sign indicates an action that NEEDS to be
taken to avoid a hazard.
4
INTRODUCTION
WARNING
Failure to heed the warnings and safety precautions contained in this manual
can result in severe injury or death. Your Polaris vehicle is not a toy and can be
hazardous to operate. This vehicle handles differently than cars, trucks or other
off-road vehicles. A collision or rollover can occur quickly, even during routine
maneuvers like turning, or driving on hills or over obstacles, if you fail to take
proper precautions.
• Read this owner’s manual. Understand all safety warnings, precautions and
operating procedures before operating the vehicle. Keep this manual with the
vehicle.
• This vehicle is an ADULT VEHICLE ONLY. NEVER operate this vehicle if you
are under age 16 and NEVER operate this vehicle without a valid driver’s
license. Never operate with a passenger under the age of 5.
5
INTRODUCTION
Vehicle Identification Numbers
Record your vehicle's identification numbers and key number in the
spaces provided. Remove the spare key and store it in a safe place. An
ignition key can be duplicated only by ordering a Polaris key blank
(using your key number) and mating it with one of your existing keys.
The ignition switch must be replaced if all keys are lost.
XXXX
Key
Number
VIN Label 7176293
Stamped VIN
Motor Serial Number
Vehicle Model Number: ___________________________________________________
Frame VIN: ____________________________________________________________
Vehicle Serial Number: ___________________________________________________
Key Number: ___________________________________________________________
6
SAFETY
Equipment Modifications
Your Polaris vehicle is designed to provide safe operation when used as
directed. Do not modify this vehicle in a way that will alter the weight
distribution of the vehicle. This type of modification may negatively
impact vehicle stability.
Failure of critical machine components may result from operation with
any modifications, especially those that increase speed or power. This
vehicle may become less stable at speeds higher than those for which it
is designed. Loss of control may occur at higher speeds.
Do not install on a Polaris vehicle any equipment that may increase the
speed or power of the vehicle, or make any other modifications to the
vehicle for these purposes. Any modifications to the original equipment
of the vehicle create a substantial safety hazard and increase the risk of
bodily injury.
The warranty on your Polaris vehicle is terminated if any equipment has
been added to the vehicle, or if any modifications have been made to the
vehicle, that increase its speed or power or alter the weight distribution
of the vehicle.
Use only Polaris-approved accessories, and familiarize yourself with
their function and effect on the vehicle before operating.
7
SAFETY
Operator Safety
WARNING
Failure to operate this vehicle properly can result in a collision, loss of control,
accident or overturn, which may result in serious injury or death. Heed all safety
warnings outlined in this section of the owner’s manual. See the OPERATION
section of the owner’s manual for proper operating procedures.
Operating Without Instruction
Operating this vehicle without proper instruction
increases the risk of an accident. The operator
must understand how to operate the vehicle
properly in different situations and on different
types of terrain. Complete the New Operator
Driving Procedures outlined on pages 40-41.
All operators must read and understand the
owner's manual and all warning and instruction
labels before operating the vehicle. Never allow a
guest to operate this vehicle until the guest has
completed the New Operator Driving Procedures
outlined on pages 40-41.
Age Restrictions
This vehicle is an ADULT VEHICLE ONLY.
NEVER operate this vehicle if you are under
age 16 and NEVER operate this vehicle
without a valid driver’s license. Never operate
with a passenger under the age of 5.
8
SAFETY
Operator Safety
Ventilation When Charging Batteries
Failure to provide adequate ventilation while charging batteries can result in an
explosion. Volatile hydrogen gas is emitted during charging and may
accumulate in pockets at the ceiling. Always ensure a minimum of 5 air changes
per hour in the charging area.
Failure to Inspect Before Operating
Failure to inspect and verify that the
vehicle is in safe operating condition
before operating increases the risk of an
accident.
Always inspect the vehicle before each
use to make sure it's in safe operating
condition.
Always follow the inspection and
maintenance procedures and schedules
described in the owner's manual.
Using Alcohol or Drugs
Riding in this vehicle after consuming
alcohol or drugs could adversely affect
operator judgment, reaction time,
balance and perception.
Never consume alcohol or drugs before
or while operating or riding in this vehicle.
9
SAFETY
Operator Safety
Seat Belts
Riding in this vehicle without wearing a seat belt increases the risk of serious
injury in the event of an accident or sudden stop. Riders must wear seat belts at
all times. Seat belts reduce the severity of injury in the event of a sudden stop or
accident. Always make sure the seat belts are secured for both the operator and
passenger before riding.
Poor Visibility
Operating the vehicle in darkness or inclement weather could result in a collision
or accident, especially if operating on a road or street. This vehicle is not
equipped with highway-approved lights. Use caution and drive at reduced
speeds in conditions of reduced visibility such as fog, rain and darkness. Clean
headlights frequently and replace burned out headlamps promptly.
Accessories
Non-approved accessories may seriously affect vehicle stability. Using accessories not approved by Polaris for use on this vehicle could cause loss of control or
an accident. Never operate with accessories not approved by Polaris for use on
this vehicle.
10
SAFETY
Operator Safety
Carrying a Passenger
Never carry a passenger until you have operated this vehicle for at least two
hours and have completed the New Operator Driving Procedures outlined on
pages 40-41. Passengers must always be seated in a passenger seat with seat
belt secured. Never drive the vehicle until all occupants are properly seated.
Carrying Multiple Passengers
Carrying more than one passenger can affect the operator’s ability to steer and
operate the controls, which increases the risk of loss of control, accident or
overturn.
Never allow more than two passengers to occupy the rear seat.
Operating on Public Roads
Operating this vehicle on public streets, roads or highways could result in a
collision with another vehicle.
Never operate this vehicle on any public street, road or highway, including dirt
and gravel roads, unless permitted by local regulations. In many areas it's
unlawful to operate vehicles of this type on public streets, roads and highways.
Operating at Excessive Speeds
Operating this vehicle at excessive speeds increases the operator's risk of
losing control.
Never exceed the maximum recommended speed for this vehicle. Always
operate at a speed that's appropriate for the terrain, the visibility and operating
conditions, your skills and your passenger’s skills.
11
SAFETY
Operator Safety
Turning Improperly
Turning improperly could cause loss of traction, loss of control, accident or
overturn. Always follow proper procedures for turning as described in the
owner's manual.
Avoid sharp turns. Never turn at a fast speed. Never make abrupt steering
maneuvers. Practice turning at slow speeds before attempting to turn at faster
speeds.
Physical Control of the Vehicle
Removing hands from the steering wheel or hand holds or removing feet from
the floor while riding increases the risk of loss of control and accident or
overturn. The operator should always keep both hands on the steering wheel
during operation. Passenger should always be seated in the passenger seat
with both feet on the floor and with both hands securely grasping the hand
holds.
Always keep head, hands and feet inside the vehicle at all times.
Jumps and Stunts
Exhibition driving increases the risk of an accident or overturn. DO NOT do
power slides, “donuts”, jumps or other driving stunts. Avoid exhibition driving.
Descending Hills Improperly
Improperly descending a hill could cause loss of control or overturn. Always
follow proper procedures for traveling down hills as described in the owner's
manual.
• Use the brake pedal to control speed when descending a hill. Never travel
down a hill at high speed.
• Always descend a hill with the direction selector on FORWARD. Never
descend a hill in neutral.
• Always check the terrain carefully before descending a hill.
• Avoid traveling down a hill at an angle, which would cause the vehicle to lean
sharply to one side. Travel straight downhill.
12
SAFETY
Operator Safety
Improper Hill Climbing
Improper hill climbing could cause loss of control or overturn. Use extreme
caution when operating on hills. Always follow proper procedures for hill
climbing as described in the owner's manual. See page 45.
Crossing Slopes
Crossing a slope is not recommended. Improper procedure could cause loss of
control or overturn. Avoid crossing a slope unless absolutely necessary.
If crossing a slope is unavoidable, always follow proper procedures as
described in the owner's manual. See page 48.
Stalling While Climbing a Hill
Stalling or rolling backwards while climbing a hill could cause an overturn.
Maintain a steady speed when climbing a hill.
If you lose all forward speed:
Apply the brakes gradually until the vehicle is fully stopped. Place the Forward/
Reverse Switch in reverse and slowly allow the vehicle to roll straight downhill
while applying light brake pressure to control speed.
Operating in Unfamiliar Terrain
Failure to use extra caution when operating on unfamiliar terrain could result in
an accident or overturn.
Unfamiliar terrain may contain hidden rocks, bumps, or holes that could cause
loss of control or overturn.
Travel slowly and use extra caution when operating on unfamiliar terrain. Always
be alert to changing terrain conditions.
13
SAFETY
Operator Safety
Operating on Slippery Terrain
Operating on excessively rough, slippery or loose terrain could cause loss of
traction, loss of control, accident or overturn.
Do not operate on excessively rough, slippery or loose terrain. Always use extra
caution on rough, slippery or loose terrain.
Operating Improperly in Reverse
Improperly operating in reverse could result in a collision with an obstacle or
person. Always follow proper operating procedures as outlined in this manual.
See page 47.
Before backing, always check for obstacles or people behind the vehicle. When
it's safe to proceed, back slowly.
Improper Tire Maintenance
Operating this vehicle with improper tires or with improper or uneven tire
pressure could cause loss of control, accident or overturn.
Always use the size and type of tires specified for your vehicle. Always maintain
proper tire pressure as described in the owner's manual and on safety labels.
14
SAFETY
Operator Safety
Operating Over Obstacles
Improperly operating over obstacles could cause loss of control or overturn.
Never operate over obstacles.
Skidding or Sliding
Skidding or sliding can cause loss of control or overturn. Always follow proper
procedures for operating on slippery surfaces as described in the owner's
manual.
When operating on slippery surfaces such as ice or loose gravel, reduce speed
and use extra caution to reduce the chance of skidding or sliding.
Do not operate on excessively slippery surfaces.
Operating a Damaged Vehicle
Operating a damaged vehicle can result in an accident with serious injury or
death. After any overturn or accident, have a qualified service dealer inspect the
entire vehicle for possible damage, including (but not limited to) brakes and
steering systems.
Unauthorized Use of the Vehicle
Leaving the keys in the ignition can lead to unauthorized use of the vehicle,
which could result in an accident or overturn. Always remove the ignition key
when the vehicle is not in use.
15
SAFETY
Operator Safety
Precautions During Maintenance
Always follow all safety instructions in the maintenance portion of this owner’s
manual, as well as the following:
• Make sure the vehicle is properly immobilized before beginning any maintenance.
• Always block the chassis securely before working under the vehicle.
• Always disable the vehicle’s electrical system before performing maintenance
on the vehicle. Remove the key. Turn the Master On-Off switch located in the
battery component to the OFF position.
• Insulate any tools used within the battery area to prevent sparks or battery
explosion caused by shorting the battery terminals or wiring. Remove the batteries, or cover the exposed terminals with an insulating material.
FOR MORE INFORMATION ABOUT SAFETY
call Polaris at 1-800-342-3764.
16
SAFETY
Safety Labels and Locations
Warning labels have been placed on the vehicle for your protection.
Read and follow the instructions of the labels on the vehicle carefully. If
any of the labels depicted in this manual differ from the labels on your
vehicle, always read and follow the instructions of the labels on the
vehicle.
If an informational or graphic label becomes illegible or comes off, contact your Polaris dealer to purchase a replacement. Replacement safety
labels are provided by Polaris at no charge. The part number is printed
on the label.
Warning General
Age Warning
Discretionary Warning
17
SAFETY
Safety Labels and Locations
General Warning
WARNING
READ OWNER’S MANUAL.
FOLLOW ALL INSTRUCTIONS AND WARNINGS.
• This vehicle does not comply with Federal Regulations for on highway use.
Check local laws for usage restrictions.
TO OPERATE:
1. Turn Key to ON position
2. Place Forward/Reverse Switch in desired position.
3. Park Brake will release and vehicle will move when accelerator pedal is
pressed.
4. To stop, release accelerator and gradually depress brake pedal.
5. Come to a complete stop before reversing direction.
6. Beeper will sound when vehicle is in Reverse.
7. Set parking brake, place the Vehicle Control Switch to Neutral, and turn Key
Switch to OFF before leaving the vehicle.
8. Remove key if vehicle is unattended.
MOTOR BRAKING:
• Electric Motor Braking provides braking when the accelerator pedal is
released.
• For parked vehicles, beeping alarm indicates vehicle roll away.
TOWING:
• When towing the vehicle, the Master ON-OFF Switch, located in the battery
compartment, MUST be in the OFF position or severe motor damage will occur.
7176198
18
SAFETY
Safety Labels and Locations
Age Warning
WARNING
Operating this vehicle if you are under
the age of 16 increases your chance of
severe injury or death.
NEVER operate this vehicle if you are
under age 16 and NEVER operate this
vehicle without a valid driver’s license.
7175566
Age Warning
19
SAFETY
Safety Labels and Locations
Discretionary Warning
WARNING
IMPROPER VEHICLE OPERATION CAN RESULT IN SEVERE INJURY OR
DEATH.
• Do not start vehicle until all occupants
are seated.
• Remain seated, holding handles while
the vehicle is in motion.
• Operate from Driver’s side only.
• Always wear your seatbelt to prevent
ejection from vehicle.
• The roof is not designed or intended to
provide rollover protection. Vehicle rollover could cause severe injury or
death. Always operate with caution.
• Never operate after or while using
Alcohol or Drugs.
• Never operate on slopes steeper than
15 degrees (15°).
Discretionary Warning
• Drive slowly straight up and down
slopes.
• Keep entire body in the vehicle at all times.
• Reduce speed and use extra caution when carrying passengers.
• Avoid sharp turns or turns during heavy acceleration.
• Operate slowly in reverse and avoid sharp turns or sudden braking.
• Make sure passengers read and follow all safety labels.
• This vehicle is restricted to a maximum of 4 occupants.
• When towing the vehicle, the Master ON-OFF Switch MUST be in the OFF
position or severe motor damage will occur.
• Place the Master ON-OFF Switch in the OFF position if storing the vehicle for
more than 5 days. Failure to do so may lead to complete battery discharge and
battery damage.
• Batteries require regular maintenance. Failure to maintain batteries in accordance with the owner’s manual can result in battery damage, vehicle malfunction, fire, and/or severe injury or death.
7176197
20
SAFETY
Safety Labels and Locations
CAUTION, MASTER SWITCH
CAUTION
• When towing the vehicle, the Master ONOFF Switch MUST be in the OFF position
or severe motor damage will occur.
• Place the Master ON-OFF Switch in the
OFF position before disconnecting
batteries or servicing the vehicle.
• Place the Master ON-OFF Switch in the
OFF position if storing the vehicle for
greater than 5 days. Failure to due so may
lead to complete battery discharge and
battery damage.
• Exposure to water may damage
electronic components.
7176200
Caution, Master Switch
21
SAFETY
Safety Labels and Locations
Passenger Safety Warning
WARNING
• DO NOT get on or off vehicle while it is in
motion.
• Remain seated, holding handles while the
vehicle is in motion.
• Always wear your seatbelt to prevent
ejection from vehicle.
• The roof is not designed or intended to
provide rollover protection. Vehicle rollover
could cause severe injury or death. Always
operate with caution.
• Keep entire body in the vehicle at all times.
• Operator should reduce speed and use
extra caution when carrying passengers.
• Read and follow all safety labels.
7176199
22
SAFETY
Safety Labels and Locations
Warning Battery
WARNING
• Battery Explosion could result in severe injury or death.
• Wear eye protection when working near batteries.
• Do not store items in the battery compartment.
• Explosive gases are released when charging batteries. Keep well ventilated.
• No smoking. Keep sparks and flames away.
• Electrical shorts can result in burns. Do not make connection between positive
and negative battery terminals.
• Sulfuric acid in batteries will burn eyes, skin and clothing. Do not tip batteries.
Keep vent caps tight and level. In event of injury, flush with water and seek
medical attention immediately.
• Always ensure batteries are properly fastened.
CONTACT YOUR AUTHORIZED POLARIS DEALER FOR ANY BATTERY
RELATED QUESTIONS.
7176202
Battery Connection
Battery Connection Decal
7176201
23
FEATURES AND CONTROLS
Component Locations
FRONT VIEW
Canopy
Steering
Wheel
Turn
Signal
Lever/
Hazard
Lights
Grab Handles
Adjustable
Headlights
Adjustable
Front
Shocks
24
Turn
Signal
Lights
FEATURES AND CONTROLS
Component Locations
REAR VIEW
Hand
Hold
Passenger Seat
T-Bar
Passenger Seat
Grab Handle
Passenger Seat
Footrest
Tail Light/Brake Light/Running Light
25
FEATURES AND CONTROLS
Component Locations
SIDE VIEW
B Pillar
A Pillar
Seat Belts
Drink Rail
26
Bag Retainer
Charging Receptacle Battery Compartment
Under Seat
FEATURES AND CONTROLS
12V
Accessory
Power Outlet
Key
Switch
Forward/
Reverse
Switch
Headlight
Switch
Battery
Discharge
Indicator
12V Accessory Power Outlet
A 12V power outlet is provided for charging cell phones and GPS
devices. Connected devices should not a exceed 2A or 24W rating.
Key Switch
Use the key switch to turn the electrical power on or off.
OFF: All electrical power is off, depends on ON/OFF switch
ON: Electrical power is on.
See page 40 for New Operator Driving Procedures.
27
FEATURES AND CONTROLS
Forward/Reverse Switch
When the Forward/Reverse switch is in
the center position, the vehicle is in
neutral and will not operate. Select forward or reverse to operate the vehicle.
Push the top of the switch to select forward operation. Push the bottom of the
switch to select reverse operation.
Forward
Neutral
Reverse
Tip: A warning alert will sound when
reverse is selected, regardless of key
position.
Headlight Switch
Use the headlight switch to turn headlights OFF, LOW BEAM, or HIGH
BEAM.
Top Position: HIGH BEAM
Center Position: LOW BEAM
Bottom Position: OFF
28
High Beam
Low Beam
Off
FEATURES AND CONTROLS
Battery Discharge Indicator
(BDI)
The battery discharge indicator shows
the amount of energy removed from
the batteries. 70% discharge is indicated by the second to the left LED bar
flashing. Full charge is indicated when
the rightmost led BAR IS LIT. Avoid
discharging the batteries more that
80%.
Battery Discharge Indicator
NOTICE: When the last bar is blinking, the gauge reflects 80% discharge.
29
FEATURES AND CONTROLS
Master On/Off Switch
The master switch is located under the seat
on the passenger side of the battery box.
ON
The switch must be in the ON position (forward) for the vehicle to operate. The switch
must be moved to the OFF position for:
OFF
• Towing the vehicle (or severe motor
damage will occur)
• Performing battery maintenance or
replacement (to disconnect all power
Master On/Off Switch
from the batteries to the vehicle)
• Storing the vehicle (to prevent battery
discharge) for more than 5 days.
NOTICE: Failure to turn off the Master On/Off switch when storing the
vehicle for a prolonged period can cause battery damage.
NOTICE: Failure to turn off the Master On/Off switch before performing
maintenance on the electrical system can cause damage to the
vehicle’s electrical components.
Multifunction Light
The green LED light, located on the motor
controller will illuminate, flashing initially
then remain on while the key is turned to the
On position AND the Master On/Off switch,
located under the seat, is in the On position.
The multifunction light is also your source
for trouble-shooting information in the
event that any electrical issues arise with the
vehicle. In normal operation the LED will
remain steady green. If a problem is
detected the light will flash, in different
sequences to indicate the type of issue to
investigate. Please refer to the Multifunction
Light Trouble-shooting Guide on page 31.
30
Multifunction Light
FEATURES AND CONTROLS
Multifunction Light
Multifunction Light Troubleshooting Guide
Flash
Sequence
OFF
1 Flash
Solution
If the light does not illuminate, verify that the master on/off
switch is in the ON position. Check battery cable connections.
The system controller has an internal error. See your Polaris
dealer for service.
2 Flashes
Move the master on/off switch to OFF. Inspect electrical connections to the direction selector switch. Return the master on/
off switch to ON. If the light continues to flash, see your Polaris
dealer for service.
3 Flashes
Move the master on/off switch to OFF. Inspect electrical connections to the motor. Return the master on/off switch to ON. If
the light continues to flash, see your Polaris dealer for service.
4 Flashes
The line contactor requires service. See your Polaris dealer for
service.
6 Flashes
Move the master on/off switch to OFF. Inspect electrical connections to the accelerator pedal. Return the master on/off
switch to ON. If the light continues to flash, see your Polaris
dealer for service.
7 Flashes
Battery voltage is low. Move the master on/off switch to OFF.
Check battery cable connections. Return the master on/off
switch to ON. If the light continues to flash, move the master
on/off switch to OFF and use a battery tester to check each battery.
31
FEATURES AND CONTROLS
Batteries
This vehicle is equipped with six 8-volt batteries that supply the power
needed to operate the vehicle. Refer to the battery maintenance section
beginning on page 71 for battery safety warnings and safe handling and
maintenance procedures.
• Always make sure that all electrical accessories are grounded directly
to the battery (-) post. Never use the chassis or body as a ground connection.
• Always observe all battery safety warnings and safe handling procedures.
• Always keep battery terminals and connections clean and free of corrosion at all times.
• Always maintain a full charge on the batteries. For best battery life,
batteries should not be discharged more than 80% of their rated
capacity.
• New batteries should be given a full charge before use.
• New deep cycle batteries need to be cycled several times before
reaching full capacity (50-125 cycles, depending on type). Capacity
will be limited during this time.
• Vent caps should be correctly installed and tight during vehicle operation and battery charging.
• Recharge batteries at the end of every day the vehicle is operated.
Allow time for the charger to complete its charge cycle.
• The batteries in this vehicle do not have a “memory effect”. Frequent
charging will extend their life.
32
FEATURES AND CONTROLS
Brakes
Park Brake
Brake Pedal
Accelerator
Pedal
Park Brake
The park brake pedal is located in the upper left corner of the brake
pedal. To engage the park brake, depress the brake pedal firmly and tip
the park brake portion of the pedal forward with your foot until it
latches. To release the park brake, depress the accelerator.
Brake Pedal
Depress the brake pedal with moderate pressure to slow or stop the vehicle. If any of the following occurs when the brakes are applied, see your
Polaris dealer for service promptly:
• Vehicle swerves
• Vehicle stops abruptly
• Vehicle fails to stop
• Vehicle makes grinding noise
33
FEATURES AND CONTROLS
Accelerator Pedal
Depress the accelerator pedal to release the park brake and increase
vehicle speed. The key must be ON and the direction selector switch
must be in either FORWARD or REVERSE. Release the pedal to
decrease speed.
Holding the accelerator pedal down continuously will accelerate the
vehicle to the maximum designed speed. Use the brakes to control speed
when traveling down a slope.
NOTICE: Operating at excessive speeds may result in damage to drivetrain
components. Never exceed the maximum recommended speed for
this vehicle.
Turn Signals/Hazard Light
Your vehicle is equipped with turn signals and hazard lights. To apply
hazard lights pull the hazard light plate forward. To cancel the hazard
lights push the turn signal arm up or down.
Hazard Light Plate
34
FEATURES AND CONTROLS
Seats
Driver’s Seatback
Adjustment
There is not an adjustment for the
front seat base or rear seats.You can
adjust the driver’s side seatback. To
adjust pull on the knob on the
driver’s side B-pillar. Rotate the seatback into the desired position and
ensure the knob completely returns
to its starting position. Test the seatback to ensure that it is secure before
operating.
Front Seat Adjustment
35
FEATURES AND CONTROLS
Seats
Open Seat to Access Batteries
To Flip the Seat Up for Service
1. Make sure the driver’s side seatback is in rearmost position
2. Rotate the driver and passenger buckles underneath the seatbacks
3. Grasping the driver or passenger side armrest, rotate the seat forward until it rests against the steering wheel.
To Completely Remove the Seat
Follow Step 1 through 3 from above. Seek the assistance of a friend or
service technician. Lift the seat by both hand rails while it is in the vertical position until the front mounting brackets come loose. Be careful not
to damage the seat during removal.
Seat Cleaning
A solution of 10% household liquid dish soap with warm water applied
with a soft damp cloth will remove most dirt and stains.
36
FEATURES AND CONTROLS
Seat Belts
Falling from a moving vehicle could result in serious injury or death. Always fasten
your seat belt securely before operating or riding in this vehicle.
Always make sure the seat belts are secured for both the operator and
passengers before riding.
To wear the seat belt properly, follow this procedure:
1. Place the belt across your lap as low on your hips as possible. Make
sure that the belt is not twisted.
2. Push the latch plate into the buckle until it clicks.
3. Release the strap, it will self-tighten.
To release the seat belt, press the square red button in the buckle's center.
Seat Belt Inspection
Inspect all seat belts for proper operation before each use of the vehicle.
1. Push the latch plate into the buckle until it clicks. The latch plate
must slide smoothly into the buckle. A click indicates that it's
securely latched.
2. Push the red release latch in the middle of the buckle to make sure it
releases freely.
3. Check the belt webbing for wear, cuts or damage. If any irregularities are found, have the seat belt system checked and/or replaced by
an authorized Polaris dealer.
4. To clean dirt or debris from the seat belts, sponge the straps with
mild soap and water. Do not use bleach, dye or household detergents.
37
FEATURES AND CONTROLS
Passenger Seat/Bag Retainer
To access the passenger seat, lift the passenger seat release handle and
push down the seat until it is securely resting on the passenger seat
bumpers. Pull the passenger T-bar handle forward until it latches.
To access the bag retainer, lift on the passenger seat release handle and
push the passenger T-bar handle down. Lift up the seat until it is
securely fastened in place.
Passenger Release Handle
38
OPERATION
Brake System Break-in
Apply only moderate braking force for the first 50 stops. Aggressive or
overly forceful braking when the brake system is new could damage
brake shoes and drums.
Pre-Ride Inspection
Failure to inspect and verify that the vehicle is in safe operating condition before operating increases the risk of an accident. Always inspect
the vehicle before each use to make sure it's in safe operating condition.
Item
Remarks
Page
Batteries
Ensure batteries are fully charged
43
Brake system
Ensure proper operation
33
63
Steering
Ensure free operation
63
Tires
Inspect condition and pressure
65
Wheels/fasteners
Inspect, ensure fastener tightness
66
Frame nuts, bolts, fasteners
Inspect, ensure tightness
-
Accelerator
Ensure proper operation
34
Indicator lights/switches
Ensure proper operation
27-31
Headlamp
Check operation, apply Polaris dielectric grease when lamp is replaced
69
Seat Latches
Push down on both seat backs to
ensure the latches are secure
38
Seat Belts
Check length of belt for damage,
check latches for proper operation
37
39
OPERATION
New Operator Driving Procedures
1. Read and understand the owner's manual and all warning and
instruction labels before operating this vehicle.
2. Disconnect the battery charger (if connected). See page 72.
3. Perform the pre-ride inspection. See page 39.
4. Do not carry a passenger until you have at least two hours of driving
experience with this vehicle.
5. Sit in the driver's seat and fasten the seat belt.
6. Make sure the direction selector switch is in the proper position for
your intended direction of travel.
7. Make sure the front wheels are turned in the intended direction of
travel.
8. Apply the brakes.
9. Turn the key to the ON position.
10. Select an open area that allows room to familiarize yourself with
vehicle operation and handling. Check for obstacles and people in
your driving area.
11. Keeping both hands on the steering wheel, release the brakes and
depress the accelerator with your right foot to begin driving.
12. Drive slowly at first. On level surfaces, practice starting, stopping,
turning, maneuvering, using the accelerator and brakes and driving
in reverse. Learn how the vehicle handles when making both left
and right turns at a slow speed.
13. Increase speed only after mastering all maneuvers at a slow speed.
14. After you become skilled at making turns and begin to operate at
faster speeds, follow these precautions:
• Avoid abrupt starts and stops.
• Avoid sharp turns and abrupt steering maneuvers.
• Never turn at a fast speed.
• Operate at speeds appropriate for your skills, the conditions and
the terrain.
40
OPERATION
New Operator Driving Procedures
Stopping
1. Release the accelerator pedal completely.
2. Depress the brake pedal and brake to a complete stop.
Parking
1. Stop the vehicle on a level surface.
2. Engage the park brake.
Tip: A roll-away alert will sound if the vehicle begins to roll away after being
parked. Return to the vehicle immediately and make sure the park brake is
engaged.
3. If the vehicle will be parked for more than a few minutes, turn the
key off. Remove the key and move the direction selector switch to
the neutral position.
4. Any time the vehicle will be parked for more than a few hours,
move the Master On/Off switch to the OFF position and follow the
recommended storage procedures. See page 55.
41
OPERATION
Driving with Passengers
1. Complete the New Operator Driving Procedures outlined on pages
40-41.
2. Perform the pre-ride inspection. See page 39.
3. Make sure all occupants are properly seated and have their seatbelts
secured.
4. Slow down. Always travel at a speed appropriate for your skills,
your passenger's skills, and operating conditions. Avoid unexpected
or aggressive maneuvers that could cause discomfort or injury to
your passengers.
5. Vehicle handling may change with passengers on board. Allow
more time and distance for braking.
6. Always follow all operating guidelines as outlined on safety labels
and in this manual.
42
OPERATION
Battery Use
• New batteries should be given a full charge before use.
• New deep cycle batteries need to be cycled several times before
reaching full capacity (50-125 cycles, depending on type). Capacity
will be limited during this time. Always make sure that all electrical
accessories are grounded directly to the battery (-) post. Never use the
chassis or body as a ground connection.
• Always observe all battery safety warnings and safe handling procedures.
• Always keep battery terminals and connections free of corrosion.
• Always maintain a full charge on the batteries. For best battery life,
batteries should not be discharged 80% of their rated capacity. Proper
battery sizing will help avoid excessive discharge.
• Batteries should be kept clean and free of dirt and corrosion at all
times.
• Vent caps should be correctly installed and tight during vehicle operation and battery charging.
43
OPERATION
Driving on Slippery Surfaces
WARNING
Skidding or sliding can cause loss of
control or overturn (if tires regain
traction unexpectedly). When
operating on slippery surfaces such
as ice or loose gravel, reduce speed
and use extra caution to reduce the
chance of skidding or sliding out of
control. Do not operate on
excessively slippery surfaces.
When driving on slippery surfaces
such as wet trails, loose gravel, or
ice, be alert for the possibility of
skidding and sliding.
Follow these precautions when
encountering slippery conditions:
1. Slow down before entering
slippery areas.
2. Maintain a high level of alertness, reading the trail and avoiding
quick, sharp turns, which can cause skids.
3. Correct a skid by turning the steering wheel in the direction of the
skid. Never apply the brakes during a skid.
44
OPERATION
Driving Uphill
Whenever traveling
uphill, follow these
precautions:
1. Always check the
terrain carefully
before ascending a
hill.
2. Avoid steep hills
(15° maximum).
3. Drive straight
15° maximum
uphill.
4. Never climb hills
with excessively
slippery or loose surfaces.
5. Proceed at a steady rate of speed and accelerator position. Never
apply full throttle suddenly.
6. Avoid unnecessary changes in speed or direction.
7. Never go over the crest of a hill at high speed. An obstacle, a sharp
drop, or another vehicle or person could be on the other side of the
hill.
8. If the vehicle stalls while climbing a hill, apply the brakes. Place the
Direction Selector switch in reverse and slowly allow the vehicle to
roll straight downhill while applying light brake pressure to control
speed.
45
OPERATION
Driving Downhill
Whenever descending a
hill, follow these precautions:
1. Avoid steep hills (15°
maximum).
2. Always descend a hill
with the direction
selector switch in forward. Never descend a
hill with the switch on
neutral.
15° maximum
WARNING! Coasting down a hill could result in excessive speed, which could
result in loss of control. Never travel down a hill at high speed.
3. Use the brake pedal to control speed when descending a hill.
4. Always check the terrain carefully before descending a hill.
Avoid traveling down a hill at an angle, which would cause the vehicle
to lean sharply to one side. Travel straight downhill.
46
OPERATION
Driving in Reverse
Follow these precautions
when operating in reverse:
1. Always check for obstacles or people behind
the vehicle.
2. Apply the pedal lightly.
Never press quickly on
the accelerator pedal.
3. Back slowly.
4. Apply the brakes lightly
for stopping.
5. Avoid making sharp
turns.
47
OPERATION
Driving on a Sidehill (Sidehilling)
Driving on a sidehill is not
recommended. Improper procedure could cause loss of
control or overturn. Avoid
crossing the side of any hill
unless absolutely necessary.
If crossing a hill is unavoidable, follow these precautions:
1. Drive slowly and use
extreme caution.
2. If the vehicle begins to
overturn, or if it feels as if
it may overturn, immediately turn downhill.
3. Avoid obstacles and changes in terrain that may lower or raise one
side of the vehicle or cause the vehicle to slide.
4. If the vehicle begins to slide downhill, immediately turn downhill to
stop the slide, or stop the vehicle and maneuver slowly and carefully until the vehicle can be driven straight downhill.
48
OPERATION
Parking on an Incline
A rolling vehicle can result in serious injury. Avoid parking on an
incline. If parking on an incline is unavoidable, follow these precautions:
1. Set the Parking Brake.
2. Turn the Forward/Reverse switch to Neutral.
3. Block the rear wheels on the downhill side, or park the vehicle in a
sidehill position instead
49
OPERATION
Hauling Cargo
WARNING
Overloading the vehicle or carrying or towing cargo improperly can alter vehicle
handling and may cause loss of control or brake instability. Always follow these
precautions when hauling cargo:
Never exceed the stated load capacity for this vehicle.
REDUCE SPEED AND ALLOW GREATER DISTANCES FOR BRAKING
WHEN HAULING CARGO.
NEVER EXCEED THE MAXIMUM WEIGHT CAPACITY of the vehicle. When
determining the weight you are adding to the vehicle, include the weight of the
operator, passenger, accessories, loads in the rack or box. The combined
weight of these items must not exceed the maximum weight capacity.
Always load the cargo area with the load as far forward and as low as possible.
When operating over rough or hilly terrain, reduce speed and cargo to maintain
stable driving conditions.
Always operate the vehicle with extreme care when hauling loads. Slow down.
SECURE ALL LOADS BEFORE OPERATING. Unsecured loads can create
unstable operating conditions, which could result in loss of control of the vehicle.
OPERATE ONLY WITH STABLE AND SAFELY ARRANGED LOADS. When
handling off-centered loads that cannot be centered, securely fasten the load
and operate with extra caution. Always attach the tow load to the hitch point
designated for your vehicle.
HEAVY LOADS CAN CAUSE BRAKING AND CONTROL PROBLEMS. Use
extreme caution when applying brakes with a loaded vehicle. Avoid terrain or
situations that may require backing downhill.
USE EXTREME CAUTION when operating with loads that extend over the rack
sides. Stability and maneuverability may be adversely affected, causing the
vehicle to overturn.
DO NOT TRAVEL FASTER THAN THE RECOMMENDED SPEEDS. Vehicle
should never exceed 10 mph (16 kph) while towing a load on a level grass
surface. Vehicle speed should never exceed 5 mph (8 kph) when towing loads in
rough terrain, while cornering, or while ascending or descending a hill.
50
OPERATION
Towing the Vehicle
Follow these procedures when towing the vehicle:
1. Place the direction selector switch in the NEUTRAL position.
2. Move the master ON/OFF switch to the OFF position.
3. Turn the key off.
4. Always follow these precautions when towing this vehicle:
• Do not operate faster than 12 mph (19 km/h).
• Do not tow on public streets.
• Do not allow passengers in the towed vehicle.
• Avoid abrupt starts and stops.
• Avoid sharp turns and abrupt steering maneuvers.
• Avoid towing on a hill.
51
OPERATION
Transporting the Vehicle on a Trailer
When transporting the vehicle for a long distance or on public streets,
always use a trailer with an approved load rating of 1200 lbs. (544 kg)
per vehicle being transported. Follow these procedures when trailering
the vehicle:
1. Place the direction selector switch in the NEUTRAL position.
2. Engage the park brake.
3. Remove the key to prevent loss during transporting.
4. If the trailer is not enclosed, remove the windshield (if equipped).
5. Always tie the frame of the Polaris vehicle to the trailer securely
with suitable straps or rope.
6. Always follow these precautions when trailering the vehicle:
• Do not allow passengers on the trailer or in the trailered vehicle.
• Reduce speed and drive with caution.
7. Remove all personal equipment and/or golf bags before towing
vehicle on a trailer.
52
CLEANING
Washing the Vehicle
Keeping your Polaris vehicle clean will not only improve its appearance
but it can also extend the life of various components.
NOTICE: High water pressure may damage components. Polaris recommends
washing the vehicle by hand or with a garden hose, using mild soap.
Certain products, including insect repellents and chemicals, will
damage plastic surfaces. Do not allow these types of products to
contact the vehicle.
The best and safest way to clean your Polaris vehicle is with a garden
hose and a pail of mild soap and water.
1. Use a professional-type washing cloth, cleaning the upper body first
and the lower parts last.
2. Rinse with clean water frequently.
3. Dry surfaces with a chamois to prevent water spots.
Washing Tips
•
•
•
•
Avoid the use of harsh cleaners, which can scratch the finish.
Do not use a power washer to clean the vehicle.
Do not use medium to heavy duty compounds on the finish.
Always use clean cloths and pads for cleaning and polishing. Old or
reused cloths and pads may contain dirt particles that will scratch the
finish.
• Clean the windshield with a non-abrasive glass cleaning solution and
a soft cloth.
• Clean seats with a vinyl cleaner and conditioner.
53
CLEANING
Washing the Vehicle
If a high pressure water system is used for cleaning (not recommended),
exercise extreme caution. The water may damage components and could
remove paint and labels. Avoid directing the water stream at the following items:
• Electrical components, wiring, switches and controls, such as turn
signals and dash controls.
• Wheel bearings
• Brakes
• Cab and body panels
• Labels and decals
If warning and safety labels are damaged, contact your Polaris dealer for
free replacement.
Grease all zerk fittings immediately after washing.
Polishing the Vehicle
Polaris recommends the use of common household aerosol furniture
polish for polishing the finish on your Polaris vehicle. Follow the
instructions on the container.
Polishing Tips
• Avoid the use of automotive products, some of which can scratch the
finish of your vehicle.
• Always use clean cloths and pads for cleaning and polishing. Old or
reused cloths and pads may contain dirt particles that will scratch the
finish.
54
STORAGE
Storing the Vehicle
Any time the vehicle will be parked for more than a few hours, follow
the recommended storage procedures:
1. Make any necessary repairs and clean the vehicle. See page 53.
2. Clean the batteries. See page 72.
3. Store the vehicle out of the sun in a cool, dry place.
4. Be sure the storage area is well ventilated.
5. Move the Master On/Off switch to the OFF position.
6. Do not engage the park brake.
7. Verify that tire pressure is at specification.
8. Block the wheels to prevent rolling.
9. Fully charge the batteries. Leave the charger connected to maintain
a full charge during the storage period, or check battery voltage
each month during storage and recharge as needed to maintain a full
charge. See page 72. If the charger remains connected, check it
monthly to verify proper operation.
Tip: Do not use plastic or coated materials. They do not allow enough ventilation
to prevent condensation, and may promote corrosion and oxidation.
WARNING! Do not cover the vehicle while the charger is connected.
Dangerous levels of Hydrogen gas could accumulate.
55
STORAGE
Removal from Storage
1.
2.
3.
4.
5.
6.
56
Inspect all battery connections.
Verify that batteries are fully charged.
Verify that tire pressure is at specification.
Perform the pre-ride inspection. See page 39.
Inspect and verify the tightness of the bolts, nuts and other fasteners.
Lubricate at the intervals outlined in the Periodic Maintenance
Chart beginning on page 57.
MAINTENANCE
Periodic Maintenance Chart
Careful periodic maintenance will help keep your vehicle in the safest,
most reliable condition. Inspection, adjustment and lubrication of
important components are explained in the periodic maintenance chart.
Inspect, clean, lubricate, adjust and replace parts as necessary. When
inspection reveals the need for replacement parts, use genuine Polaris
parts available from your Polaris dealer.
Record maintenance and service in the Maintenance Log beginning on
page 82.
Service and adjustments are important for proper vehicle operation. If
you're not familiar with safe service and adjustment procedures, have a
qualified dealer perform these operations.
Maintenance intervals in the following chart are based upon average
riding conditions and an average vehicle speed of approximately ten
(10) miles per hour. Vehicles subjected to severe use must be inspected
and serviced more frequently.
Severe Use Definition
• Frequent exposure to mud, water or sand
• Prolonged low speed, heavy load operation
• Cold weather operation
57
MAINTENANCE
Periodic Maintenance Chart
Maintenance Chart Key
X Perform these operations more often for vehicles subjected to
severe use.
n Have an authorized Polaris dealer perform these services.
WARNING! Improperly performing the procedures marked with a n could result
in component failure and lead to serious injury or death. Have an authorized
Polaris dealer perform these services.
Perform all services at whichever maintenance interval is reached first.
Item
Maintenance Interval
(whichever comes first)
Hours Calendar
Remarks
Miles
(Km)
n Steering
-
Pre-Ride
-
Tires
-
Pre-Ride
-
Batteries
-
Pre-Ride
-
Brake system
-
Pre-Ride
-
Wheels/fasteners
-
Pre-Ride
-
Frame fasteners
-
Pre-Ride
-
Headlamp/tail
lamp
-
Daily
-
X Brake shoe wear
10 H
Monthly
100 (160)
Inspect periodically
25 H
Monthly
250 (400)
Check terminals; clean; test
n
Batteries
58
Check operation; apply
dielectric grease if replacing
MAINTENANCE
Periodic Maintenance Chart
Item
Maintenance Interval
Remarks
(whichever comes first)
Hours Calendar
Miles
(Km)
n Brake and Acceler- 30 H
3M
300 (500)
Inspect; adjust; lubricate;
at intervals or after submersion in water
X General
lubrication
50 H
3M
500 (800)
Lubricate all fittings, pivots,
cables, etc.
1st 10
h
30 h
after
3M
300 (500)
Inspect; adjust
n Steering Kingpins
30 H
3M
300 (500)
Inspect; lubricate;
at intervals or after submersion in water
X Wiring
100 H
12 M
1000 (1600) Inspect for wear, routing,
security; apply dielectric
grease to connectors
subjected to water, mud, etc.
n Front wheel
100 H
12 M
1000 (1600) Inspect; replace as needed
n Toe adjustment
-
Inspect periodically; adjust
when parts are replaced
X Headlight aim
-
Adjust as needed
ator Pedals
n Brake Cables
bearings
X Perform these procedures more often for vehicles subjected to severe use.
n Have an authorized Polaris dealer perform these services.
59
MAINTENANCE
Lubrication Recommendations
Check and lubricate all components at the intervals outlined in the Periodic Maintenance Chart beginning on page 59, or more often under
severe use, such as wet or dusty conditions. Items not listed in the chart
should be lubricated at the general lubrication interval.
Item
Lube
Method
Steering Kingpins
Polaris Premium all Season Locate fittings and grease.
Grease or grease
conforming to NLGI No. 2
Brake and Accelerator
pedals
Polaris Premium all Season Locate fittings and grease.
Grease or grease
conforming to NLGI No. 2
Lubricate
Kingpin
60
MAINTENANCE
Transaxle
Transaxle Specification Chart
Use of other fluids may result in improper operation of components.
Transaxle
Lubricant
Capacity
Fill Plug
Torque
Transaxle
Lubricant Gearcase Polaris PN
2873602
12 oz.
(355 ml)
20-30 ft. lbs.
(27-41 Nm)
61
MAINTENANCE
Speed Control System/Accelerator Pedal
WARNING
Failure to check or maintain proper operation of the accelerator pedal
system can result in an accident and lead to serious injury or death if the
accelerator pedal sticks during operation.
Never start or operate this vehicle if it has a sticking or improperly operating accelerator pedal.
Immediately contact your dealer for service if accelerator pedal problems arise.
Always check the pedal for free movement and return before and during
operation.
•
62
The vehicle will not operate if the accelerator pedal is
depressed when the key is switched on. The vehicle will operate normally after the accelerator pedal is returned to rest.
MAINTENANCE
Brakes
The rear brakes are mechanical drum type brakes activated by the brake
pedal. See page 33.
Always check brake pedal travel before each use of the vehicle. When
applied, the brake pedal should feel firm.
If you discover any irregularities in brake system operation, including
excessive pedal travel, contact your dealer for proper diagnosis and
repairs.
WARNING! Operating the vehicle with a spongy brake pedal can result in loss
of braking, which could cause an accident resulting in severe injury or death.
Never operate the vehicle with a spongy-feeling brake pedal.
Steering Wheel Inspection
Check the steering wheel for smooth operation at the intervals outlined
in the Periodic Maintenance Chart beginning on page 57.
1. Position the vehicle on level ground.
2. Lightly turn the steering wheel left and right.
3. If there is excessive freeplay or strange noises, or the steering feels
rough or "catchy," have the steering system inspected by an authorized Polaris dealer.
63
MAINTENANCE
Suspension Settings
The front suspension shocks are preload adjustable, with three settings
on each axle.
Lowest (Softest)
Setting
Highest (Stiffest)
Setting
Adjustment
Cam
The suspensions are set on the middle setting at the factory. This setting
is appropriate for nearly all riding conditions.
• Always apply the same adjustment setting to both wheels.
64
MAINTENANCE
Tires
WARNING
Operating your vehicle with worn tires will increase the possibility of skidding,
loss of control and an accident, which could result in serious injury or death.
Always replace tires when the tread depth measures 1/8" (3 mm) or less.
Improper tire inflation or the use of non-standard size or type of tires may
adversely affect vehicle handling, which could result in vehicle damage or
personal injury. Always maintain proper tire pressure. When replacing tires,
always use original equipment size and type.
Tire Tread Depth
Always replace tires
when tread depth is worn
to 1/8" (3 mm) or less.
1/8" (3 mm)
Tire Rotation
Tire rotation is recommend in intervals of 1,00
0r 1,500 miles for this
vehicle. Tires should be rotated in Rearward-Cross pattern as recommended by the Tire and Rim Association. This will help with uneven
tire wear due to the weight distribution.
FRONT
BACK
65
MAINTENANCE
Axle and Wheel Nut Torque Specifications
Inspect the following items occasionally for tightness, and if they've
been loosened for maintenance service. Do not lubricate the stud or the
lug nut.
Front
40 ft. lbs.
(54 Nm)
Rear
95-115 lbs.
(129-156 Nm)
Fastener
Nut Torque
Wheel Lug Nut
90 ft. lbs. (122 Nm)
Front Hub Nut
40 ft. lbs. (54 Nm)
Rear Hub Nut
95-115 ft. lbs. (129-156 Nm)
66
MAINTENANCE
Tires
WARNING! Improperly installed wheels can adversely affect tire wear and
vehicle handling, which can result in serious injury or death. Always ensure that
all nuts are torqued to specification. Do not service axle nuts that have a cotter
pin installed. See your Polaris dealer.
Wheel Removal
1. Position the vehicle
on a flat level surface.
2. Place the gear selector switch in neutral.
3. Apply the parking
brake.
4. Loosen the wheel
nuts slightly.
5. Elevate one side of
the vehicle by placing a suitable stand under the frame. Do not ever
elevate both rear wheels at the same time! Parking brake only locks
rear wheels, and vehicle can roll.
6. Remove the wheel nuts. Remove the wheel.
67
MAINTENANCE
Tires
Wheel Installation
1. Place the transmission in NEUTRAL. Rear
2. Place the wheel in
the correct position
on the wheel hub. Be
sure the valve stem
is toward the outside and rotation
arrows on the tire
point toward forward rotation.
3. Attach the wheel
Front
nuts and finger
tighten.
4. Carefully lower the vehicle to the ground.
5. Torque the wheel nuts to specification. See page 66.
68
MAINTENANCE
Lights
WARNING! Poor lighting while driving can result in severe injury or death.
Headlight and tail light lenses become dirty during normal operation. Wash the
headlights frequently to maintain lighting quality.
Headlight Lamp Replacement
Do not service the headlamps until they've cooled sufficiently.
1. Unplug the headlamp
from the wiring harness. Wiring
Be sure to pull on the
Harness
connector, not on the wiring.
2. Turn the lamp counterclockwise to remove it.
3. Install the new lamp.
Make sure the tab on the
lamp locates properly in
Lamp
the housing.
4. Reinstall the harness
assembly into the headlight assembly.
69
MAINTENANCE
Lights
Brake Lights
When the brake pedal is depressed, the brake light comes on. Check the
brake light before each ride.
1. Turn the ignition switch to the ON position.
2. Apply the brakes.If the light doesn't come on, check the wiring, the
brake switch or the tail light assembly.
70
MAINTENANCE
Batteries
WARNING
Battery posts, terminals and related components contain lead and lead
compounds, chemicals known to cause cancer and reproductive harm. Always
wash your hands after touching or handling the batteries.
WARNING
Charging a damaged battery can result in serious injury. Never attempt to
charge a frozen or bulging battery. Discard the battery appropriately and install a
new battery.
WARNING
Improperly connecting or disconnecting battery cables can result in an explosion
and cause serious injury or death.
WARNING
Battery electrolyte is poisonous. It contains sulfuric acid. Serious burns can
result from contact with skin, eyes or clothing.
Antidote:
External: Flush with water.
Internal: Drink large quantities of water or milk. Follow with milk of magnesia,
beaten egg, or vegetable oil. Call physician immediately.
Eyes: Flush with water for 15 minutes and get prompt medical attention.
Batteries produce explosive gases. Keep sparks, flame, cigarettes, etc. away.
Ventilate when charging or using in an enclosed space. Always shield eyes
when working near batteries. KEEP OUT OF REACH OF CHILDREN.
71
MAINTENANCE
Batteries
Battery Cleaning
If cleaning is necessary, remove the corrosion with a stiff wire brush.
Wash with a solution of one tablespoon baking soda and one cup water.
Rinse well with tap water and dry off with clean shop towels. Coat the
terminals with dielectric grease or petroleum jelly. Be careful not to
allow cleaning solution or tap water into the batteries.
Battery Charging
When not in use, park the vehicle indoors and connect the battery
charger. The vehicle’s charging receptacle is located on the body below
the driver’s seat base.
WARNING! Failure to provide adequate ventilation while charging batteries can
result in an explosion. Hydrogen gas is emitted during charging and will rise and
accumulate at the ceiling. Always ensure a minimum of five (5) air changes per
hour in the charging area. Never charge the batteries in an area subject to a
flame or spark, including areas containing gas or propane water heaters and
furnaces. Do not smoke in the charging area.
1. Position the vehicle indoors
on a level surface. Make
sure the charging area is
well ventilated.
2. Open any door enclosures
or zippers.
3. Inspect charger cords and
receptacles for cracks,
loose connections and
frayed wiring. Replace any
Charging Receptacle
damaged components
promptly.
4. Always connect the charger
to the vehicle first, then plug the charger into a wall receptacle.
Make sure each charger uses a dedicated circuit to prevent overloading.
Tip: After the batteries have fully recharged, the battery charger will automatically cycle in and out of the trickle charge mode to maintain the charge.
5. When disconnecting the charger, always disconnect the charger
from the wall receptacle first, then disconnect the charger from the
vehicle.
NOTE: Refer to the manual supplied with the battery charger for further details.
72
MAINTENANCE
Batteries
Battery Fluid
A poorly maintained battery will deteriorate rapidly. Check the battery
fluid level often.
Add only distilled water. Tap water contains minerals that are harmful to
a battery.
Batteries should
always be watered
after charging unless
plates are exposed
before charging. If
exposed, plates should
be covered by approximately 1/8” of water.
Check level after
charge. The level
should be kept 1/4”
below the bottom of
the fill well in the cell
cover.
Battery Cell Cover
73
SPECIFICATIONS
BREEZE NV
Gross Vehicle Weight
Rear Seat Capacity
Maximum Weight Capacity
Rear Gearcase Oil Capacity
Overall Length/Width/Height
Wheelbase
Ground Clearance
Motor
Front Suspension
Rear Suspension
Driving System Type
Shift Type
Drive Ration Final
Tire Size Front/Rear
Tire Pressure-Front
Tire Pressure-Rear
Brakes
Headlights
Tailights
Brake lights
Auxiliary DC Outlet
74
1130 lbs. (514 kg)
300 lbs. (136 kg)
700 lbs. (317.5 kg) (riders/cargo/accessories)
12 oz. (355 ml)
113 in. (287 cm) Platform Down - 102 in. (259
cm) Platform Up / 44.5 in (113 cm) / 76 in.(193
cm) /76 in.(193 cm)
63.3 in. (161 cm)
4.6 in. (11.7 cm)
Electric
Strut Type, Independent
Semi-Independent, Solid Axle
Direct Drive Electric
F-N-R
12.44:1
205/50/R10 / 205/50/R10
27 p.s.i.
30 p.s.i.
Rear Drum / Regen
2 Hi/Low Beam 35 watts at 12 volts
LED .6 watts at 12 volts
LED 1.8 watts at 12 volts
12 volts
POLARIS PRODUCTS
Part Number
2873602
2870465
2871312
2871322
2871423
2871515
2871551
2871329
2871956
Description
Gearcase / Transmission Lubricants
Premium AGL Synthetic Gearcase Lubricant (qt.)
Pump for Gallon Jug
Grease / Specialized Lubricants
Grease Gun Kit, Premium All Season (3 oz.)
Premium All Season Grease (3 oz. cartridge)
Premium All Season Grease (14 oz. cartridge)
Premium U-Joint Lube (3 oz.)
Premium U-Joint Lube (14 oz.)
Dielectric Grease (NyogelTM)
Additives / Miscellaneous
LoctiteTM 565 Thread Sealant
75
TROUBLESHOOTING
Vehicle Doesn’t Operate
Possible Cause
Low battery voltage
Loose battery connections
Loose contactor connections
Loose electronic control box connections
Accelerator pedal depressed when turning
the key switch on
76
Solution
Recharge the battery overnight
Check all connections and tighten
Check all connections and tighten
Inspect, clean, reinstall connectors
Return accelerator pedal to rest position
WARRANTY
LIMITED WARRANTY
Polaris Sales Inc., 2100 Highway 55, Medina, MN 55340, gives a TWO YEAR LIMITED WARRANTY on all components of your Polaris vehicle against defects in material or workmanship. This warranty covers the parts and labor charges for repair or
replacement of defective parts which are covered by this warranty. This warranty begins
on the date of purchase. This warranty is transferable to another consumer during the
warranty period through a Polaris dealer. The warranty coverage ends two years from
the date of purchase.
REGISTRATION
At the time of sale, the Warranty Registration Form must be completed by your dealer
and submitted to Polaris within ten days. Upon receipt of this registration, Polaris will
record the registration for warranty. No verification of registration will be sent to the
purchaser as the copy of the Warranty Registration Form will be the warranty entitlement. If you have not signed the original registration and received the customer copy,
please contact your dealer immediately. NO WARRANTY COVERAGE WILL BE
ALLOWED UNLESS YOUR VEHICLE IS REGISTERED WITH POLARIS.
Initial dealer preparation and set-up of your vehicle is very important in ensuring trouble-free operation. Purchasing a machine in the crate or without proper dealer set-up will
void your warranty coverage.
WARRANTY COVERAGE AND EXCLUSIONS:
are not compatible with the vehicle. The exclusive remedy for breach of this warranty
shall be, at Polaris' exclusive option, repair or replacement of any defective materials, or
components or products. THE REMEDIES SET FORTH IN THIS WARRANTY ARE
THE ONLY REMEDIES AVAILABLE TO ANY PERSON FOR BREACH OF THIS
WARRANTY. POLARIS SHALL HAVE NO LIABILITY TO ANY PERSON FOR
INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY DESCRIPTION, WHETHER ARISING OUT OF EXPRESS OR IMPLIED WARRANTY OR
ANY OTHER CONTRACT, NEGLIGENCE, OR OTHER TORT OR OTHERWISE.
Some states do not permit the exclusion or limitation of incidental or consequential
damages or implied warranties, so the above limitations or exclusions may not apply to
you if inconsistent with controlling state law.
77
WARRANTY
LIMITATIONS OF WARRANTIES AND REMEDIES
The Polaris limited warranty excludes any failures that are not caused by a defect in
material or workmanship. This warranty does not cover accidental damage, normal wear
and tear, abuse or improper handling. This warranty also does not cover any vehicle that
has been altered structurally, modified, neglected, improperly maintained, used for racing, or used for purposes other than for which it was manufactured, or for any damages
which occur during trailer transit or as a result of unauthorized service or the use of
unauthorized parts. In addition, this warranty does not cover physical damage to paint or
finish, stress cracks, tearing or puncturing of upholstery material, corrosion, or defects in
parts, components or the vehicle due to fire, explosions or any other cause beyond
Polaris' control.
The Polaris limited warranty excludes any battery failures that are not caused by a defect
in material or workmanship. Warranty claims for battery replacements require specific
testing as outlined by the Polaris Warranty Department and the battery manufacturer
U.S. Battery prior to replacement. If the Polaris Warranty Department in conjunction
with U.S. Battery determines that the failure of the battery is caused by a defect in material or workmanship, Polaris will assist with the processing of the warranty claim
through U.S. Battery for a replacement battery. This warranty does not cover the time
required to test and/or diagnose issues with the battery. Consequential damage caused by
defective batteries are excluded from this warranty. Use of any charger not recommended by Polaris and/or modifications to the vehicle will void any stated or implied
warranty on the battery. Battery warranty limitations include abuse or neglect such as
improper fluid levels, loose wiring, or rusted or corroded hardware; Lack of proper
maintenance; Damage caused by improper installation of the battery; Neglect, breakage,
freezing, fire, explosion, wreckage, the addition of any chemical, operation of the battery in an overcharged condition, or the operation of the battery in an uncharged condition (below half-charge – 1.200 specific gravity); and a battery charged by systems other
than those supplied or recommended by Polaris.
This warranty does not cover the use of unauthorized lubricants, chemicals, or fuels that
are not compatible with the vehicle. The exclusive remedy for breach of this warranty
shall be, at Polaris' exclusive option, repair or replacement of any defective materials, or
components or products. THE REMEDIES SET FORTH IN THIS WARRANTY ARE
THE ONLY REMEDIES AVAILABLE TO ANY PERSON FOR BREACH OF THIS
WARRANTY. POLARIS SHALL HAVE NO LIABILITY TO ANY PERSON FOR
INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY DESCRIPTION, WHETHER ARISING OUT OF EXPRESS OR IMPLIED WARRANTY OR
ANY OTHER CONTRACT, NEGLIGENCE, OR OTHER TORT OR OTHERWISE.
Some states do not permit the exclusion or limitation of incidental or consequential
damages or implied warranties, so the above limitations or exclusions may not apply to
you if inconsistent with controlling state law.
78
WARRANTY
LIMITATIONS OF WARRANTIES AND REMEDIES
U.S. Battery’s liability shall be to replace the defective battery. Replacement shall mean
furnishing a new battery or used battery with sufficient life to complete the warranty
term, which is incidental or reasonably equivalent to the warranted product at no cost to
the purchaser during the replacement period.
ALL IMPLIED WARRANTIES (INCLUDING BUT NOT LIMITED TO THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO THE ABOVE TWO
YEAR WARRANTY PERIOD. POLARIS FURTHER DISCLAIMS ALL EXPRESS
WARRANTIES NOT STATED IN THIS WARRANTY. Some states do not allow
limitations on how long an implied warranty lasts, so the above limitation may not apply
to you if inconsistent with controlling state law.
HOW TO OBTAIN WARRANTY SERVICE
If your vehicle requires warranty service, you must take it to a Polaris Servicing Dealer.
When requesting warranty service you must present your copy of the Warranty Registration form to the dealer. (THE COST OF TRANSPORTATION TO AND FROM THE
DEALER IS YOUR RESPONSIBILITY). Polaris suggests that you use your original
selling dealer; however, you may use any Polaris Servicing Dealer to perform warranty
service.
Please work with your dealer to resolve any warranty issues. Should your dealer require
any additional assistance they will contact the appropriate person at Polaris.
This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
If any of the above terms are void because of state or federal law, all other warranty
terms will remain in effect.
Lubricants
1. Mixing oil brands or using non-recommended oil may cause engine damage. We recommend the use of Polaris gearcase oil.
2. Damage resulting from the use of non-recommended lubricants may not be covered
by warranty.
79
WARRANTY
Exported Vehicles
EXCEPT WHERE SPECIFICALLY REQUIRED BY LAW, THERE IS NO
WARRANTY OR SERVICE BULLETIN COVERAGE ON THIS VEHICLE IF IT IS
SOLD OUTSIDE THE COUNTRY OF THE SELLING DEALER'S AUTHORIZED
LOCATION.
This policy does not apply to vehicles that have received authorization for export from
Polaris Industries. Dealers may not give authorization for export. You should consult an
authorized dealer to determine this vehicle's warranty or service bulletin coverage if you
have any questions.
This policy does not apply to vehicles registered to government officials or military
personnel on assignment outside the country of the selling dealer's authorized location.
This policy does not apply to Safety Recalls.
How to Get Service
In the Country where your vehicle was purchased:
Warranty or Service Bulletin repairs must be done by an authorized Polaris dealer. If
you move or are traveling within the country where your vehicle was purchased,
Warranty or Service Bulletin repairs may be requested from any authorized Polaris
dealer who sells the same line as your vehicle.
Outside the Country where your vehicle was purchased:
If you are traveling temporarily outside the country where your vehicle was purchased,
you should take your vehicle to an authorized Polaris dealer. You must show the dealer
photo identification from the country of the selling dealer's authorized location as proof
of residence. Upon residence verification, the servicing dealer will be authorized to
perform the warranty repair.
80
WARRANTY
If You Move:
If you move to another country, be sure to contact Polaris Customer Assistance and the
customs department of the destination country before you move. Vehicles importation
rules vary considerably from country to country. You may be required to present documentation of your move to Polaris Industries in order to continue your warranty coverage. You may also be required to obtain documentation from Polaris Industries in order
to register your vehicle in your new country.
If Purchased From A Private Party:
If you purchase a Polaris product from a private citizen outside of the country in which
the vehicle was originally purchased, all warranty coverage will be denied.
Notice
If your vehicle is registered outside of the country where it was purchased, and you have
not followed the procedure set out above, your vehicle will no longer be eligible for warranty or service bulletin coverage of any kind. (Vehicles registered to Government officials or military personnel on assignment outside of the country where the vehicle was
purchased will continue to be covered by the basic warranty.)
For questions call Polaris Customer Assistance:
United States: 1-888-704-5290
Canada: 1-204-925-710
81
MAINTENANCE LOG
Use the following chart to record periodic maintenance.
DATE
82
MILES (KM)
OR HOURS
TECHNICIAN
SERVICE PERFORMED / COMMENTS
83
INDEX
A
Accelerator Pedal. . . . . . . . . . . . . . . 34
Adjustment
Seat . . . . . . . . . . . . . . . . . . . . . 35
Axle Nut Torque . . . . . . . . . . . . . . . 66
B
Batteries . . . . . . . . . . . . . . . . . 32, 71-73
Charging . . . . . . . . . . . . . . . . . 72
Cleaning. . . . . . . . . . . . . . . . . . 72
Fluid. . . . . . . . . . . . . . . . . . . . . 73
Safety Warnings. . . . . . . . . . . . 71
Battery Discharge Indicator (BDI) . 29
Before Riding. . . . . . . . . . . . . . . . . . 39
Belts, Seat . . . . . . . . . . . . . . . . . . . . 37
Brake Lights. . . . . . . . . . . . . . . . . . . 70
Brake Pedal . . . . . . . . . . . . . . . . . . . 33
Brake System Break-in . . . . . . . . . . 39
Brake, Park . . . . . . . . . . . . . . . . . . . 33
Brakes . . . . . . . . . . . . . . . . . . . . . . . 63
C
Cargo . . . . . . . . . . . . . . . . . . . . . . . . 50
Charging Batteries . . . . . . . . . . . . . . 72
Chart, Periodic Maintenance . . . . 57-59
Component Locations . . . . . . . . . 24-26
D
Driving Downhill. . . . . . . . . . . . . . . 46
Driving in Reverse. . . . . . . . . . . . . . 47
Driving on a Sidehill . . . . . . . . . . . . 46
Driving on Slippery Surfaces. . . . . . 43
Driving Procedures . . . . . . . . . . . 40-41
Driving Uphill . . . . . . . . . . . . . . . . . 45
Driving with a Passenger . . . . . . . . . 42
E
Equipment Modifications . . . . . . . . . 7
F
Fluid, Battery . . . . . . . . . . . . . . . . . . 73
Freeplay, Steering Wheel. . . . . . . . . 63
84
H
Hauling a Load. . . . . . . . . . . . . . . . .
Hauling Cargo . . . . . . . . . . . . . . . . .
Hazard Light . . . . . . . . . . . . . . . . . .
Headlight Lamp Replacement . . . . .
50
50
34
69
I
Inspection, Axle Nuts. . . . . . . . . . . .
Inspection, Pre-Ride. . . . . . . . . . . . .
Inspection, Steering Wheel . . . . . . .
Inspection, Wheel Nuts . . . . . . . . . .
Installation, Wheels . . . . . . . . . . . . .
66
39
63
66
68
K
Key Switch. . . . . . . . . . . . . . . . . . . . 27
Key, Periodic Maintenance Chart . . 58
L
Lamp Replacement, Headlight. . . . . 69
Lights . . . . . . . . . . . . . . . . . . . . . . 69-70
Lights, Brake . . . . . . . . . . . . . . . . . . 70
Lubricant Part Numbers . . . . . . . . . . 75
Lubrication Recommendations . . . . 60
M
Maintenance Log . . . . . . . . . . . . . . . 82
Maintenance, Periodic . . . . . . . . . 57-59
Multi Function Indicator Light . 27, 31
Multifunction Light . . . . . . . . . . . . . 30
N
New Operator Driving Procedures 40-41
O
Outlet, Power . . . . . . . . . . . . . . . . . . 27
INDEX
P
S
Park Brake. . . . . . . . . . . . . . . . . . . . . 33
Parking on an Incline . . . . . . . . . . . . 49
Passenger Seat/Bag Retainer . . . . . . 38
Periodic Maintenance Chart . . . . 57-59
Polaris Products . . . . . . . . . . . . . . . . 75
Polishing the Vehicle . . . . . . . . . . . . 54
Power Outlet . . . . . . . . . . . . . . . . . . . 27
Pre-Ride Inspection. . . . . . . . . . . . . . 39
R
Removal, Seat . . . . . . . . . . . . . . . . . .
Removal, Wheels . . . . . . . . . . . . . . .
Removing the Vehicle from Storage
Replacement, Headlight Lamp . . . . .
Reverse . . . . . . . . . . . . . . . . . . . . . . .
36
67
56
69
47
S
Safety Labels. . . . . . . . . . . . . . . . 17-23
Safety Symbols . . . . . . . . . . . . . . . . . . 4
Safety Warnings . . . . . . . . . . . . . . 8-16
Accessories . . . . . . . . . . . . . . . . 10
Age Restrictions . . . . . . . . . . . . . 8
Carrying a Passenger . . . . . . . . 11
Crossing Slopes. . . . . . . . . . . . . 13
Descending Hills Improperly . . 12
Excessive Speeds . . . . . . . . . . . 11
Failure to Inspect . . . . . . . . . . . . 9
Headlights . . . . . . . . . . . . . . . . . 10
Improper Hill Climbing . . . . . . 13
Improper Tire Maintenance . . . 14
Instruction . . . . . . . . . . . . . . . . . . 8
Jumps and Stunts . . . . . . . . . . . 12
Multiple Passengers . . . . . . . . . 11
Obstacles . . . . . . . . . . . . . . . . . . 15
Operating a Damaged Vehicle . 15
Physical Control . . . . . . . . . . . . 12
Poor Visibility. . . . . . . . . . . . . . 10
Precautions During Maintenance 16
Public Roads . . . . . . . . . . . . . . . 11
Safety Warnings . . . . . . . . . . . . . . . . . .
Reverse . . . . . . . . . . . . . . . . . . . 14
Seat Belts. . . . . . . . . . . . . . . . . . 10
Skidding or Sliding . . . . . . . . . . 15
Slippery Terrain . . . . . . . . . . . . 14
Stalling on a Hill . . . . . . . . . . . . 13
Turning Improperly. . . . . . . . . . 12
Unauthorized Use of the Vehicle 15
Unfamiliar Terrain . . . . . . . . . . 13
Using Alcohol or Drugs . . . . . . . 9
Ventilation When Charging . . . . 9
Seat Adjustment . . . . . . . . . . . . . . . . 35
Seat Belts. . . . . . . . . . . . . . . . . . . . . . 37
Seat Cleaning . . . . . . . . . . . . . . . . . . 36
Seat Removal . . . . . . . . . . . . . . . . . . 36
Severe Use Definition . . . . . . . . . . . . 57
Signal Words. . . . . . . . . . . . . . . . . . . . 4
Steering Wheel Inspection . . . . . . . . 63
Storage, Removal . . . . . . . . . . . . . . . 56
Storing the Vehicle . . . . . . . . . . . . . . 55
Suspension Settings. . . . . . . . . . . . . . 64
Switches
Key Switches. . . . . . . . . . . . . . . 27
T
Throttle System . . . . . . . . . . . . . . . . . 62
Tire Tread Depth . . . . . . . . . . . . . . . . 65
Tires. . . . . . . . . . . . . . . . . . . . . . . 65, 67
Torque, Axle Nuts. . . . . . . . . . . . . . . 66
Torque, Wheel Nut . . . . . . . . . . . . . . 66
Trailer Transport . . . . . . . . . . . . . . . . 52
Transaxle . . . . . . . . . . . . . . . . . . . . . . 61
Transporting the Vehicle. . . . . . . . . . 52
Tread Depth, Tire . . . . . . . . . . . . . . . 65
Turn Signals . . . . . . . . . . . . . . . . . . . 34
V
Vehicle Identification Numbers . . . . . 6
W
Warning Symbols . . . . . . . . . . . . . . . . 4
Washing the Vehicle . . . . . . . . . . 53-54
Wheel Installation . . . . . . . . . . . . . . . 68
Wheel Nut Torque. . . . . . . . . . . . . . . 66
Wheel Removal. . . . . . . . . . . . . . . . . 67
85